Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SO DO BO CO
Clamp standard DIN 32676 ISO 2852 ASME BPE ISO 2852
Piping standard DIN 11850 DIN EN ISO 1127 BS 4825-1 ISO 2037
DN 15 – DN 65 – DN 15 – DN 65 – DN 25 – DN 65 –
1.5” – 2.5” 3” – 4”
Allowable pressure [bar] DN 50 DN 100 DN 50 DN 100 DN 50 DN 150
16 10 16 10 16 10 161) 10
Table 10.8.6-1: Clamp fitting standards
1): 16 bar can be exceeded for LESER Type 481, when heavy duty clamps for the connection of the two fittings are used.
Please mind the size of the inner diameter when combining a welding end and a clamp for type 488.
The inner diameter of the clamp has to be bigger than the inner diameter of the welding end of the
clamp.
inner diameter
of welding end
pipe diameter
of the clamp
Nominal size
d1 d2 d3 d4 l3 l4
(DN)
13
10 10 34 27.5 18 2.85
14
19
15 16 34 27.5 18 2.85
20
23
20 20 34 27.5 18 2.85
24
29
25 26 50.5 43.5 21.5 2.85
30
35
32 32 50.5 43.5 21.5 2.85
36
41
40 38 50.5 43.5 21.5 2.85
42
53
50 50 64 56.5 21.5 2.85
54
65 66 70 91 83.5 28 2.85
80 81 85 106 97 28 2.85
100 100 104 119 110 28 2.85
125 125 129 155 146 28 5.6
150 150 154 183 174 28 5.6
200 200 204 233.5 225 28 5.6
Table 10.8.6-2: Clamp dimensions acc. to DIN 32676 - SO
Notes:
See DIN 32676 table 2 and table 3 for tolerances
Notes:
See ISO 2852 table 1 for tolerances
Figure 10.8.6-4: Sectional drawing of a clamp fitting acc. to ASME BPE -BO
Notes:
See ASME BPE Table DT-5.1 for tolerances
Nominal size C5 C1 C7 C2 L1 F3
12 12 16 34 27.5 2,85 16
12.7 12.7 16.7 34 27.5 2,85 16
17.2 17.2 21.2 34 27.5 2,85 18
21.3 21.3 25.3 34 27.5 2,85 20
25 25 29 50.5 43.5 2,85 20
33.7 33.7 38.1 50.5 43.5 2,85 20
38 38 42.4 50.5 43.5 2,85 20
40 40 44.8 64 56.5 2,85 20
51 51 55.8 64 56.5 2,85 25
63.5 63.5 68.9 77.5 70.5 2,85 30
70 70 75.8 91 83.5 2,85 30
76.1 76.1 81.9 91 83.5 2,85 30
Table 10.8.6-5: Clamp dimensions acc. to ISO 2852 - CO
Notes:
See ISO 2852 table 2 for tolerances
Gasket materials
Fluoro-elastomer
Buna-N (U) EPDM (E) Silicone (X) PTFE (G)
(FPM)
Hardness, Shore A 70 70 70 70 -
Tensile strength
129.3 113.8 83.6 92.4 -
[bar]
Elongation [%] 340 317 272 260 -
temperature range -53.9 -51.1 -28.9 -40 -40
[°C] - - - - -
+93.3 +140 +176.7 232.2 +93.3
Table 10.8.6-6: Gasket materials acc. Alfa Laval
Definition „Tri-Clamps“
Tri-Clover Tri-Clamp® and Tri-Weld® Fittings are part of Alfa Laval’s product line. They are
manufactured in compliance with the actual ASME BPE.
LESER offers CO Clamps which are compatible to Tri-Clamps®. See tables 10.8.6-1 and 10.8.6-7 for
differences in dimensions.
Tri-Clamp dimensions
OD ID WT A ferrule face
[inch] [inch] [mm] [inch] / [gauge] [mm] / [gauge] [inch] [mm]
½ 0.37 9.4 0.065 / 16 1.7 / 16 0.984 25.0
¾ 0.62 15.7 0.065 / 16 1.7 / 16 0.984 25.0
1 0.87 22.1 0.065 / 16 1.7 / 16 1.984 50.4
1½ 1.37 34.8 0.065 / 16 1.7 / 16 1.984 50.4
2 1.87 47.5 0.065 / 16 1.7 / 16 2.516 63.9
2½ 2.37 60.2 0.065 / 16 1.7 / 16 3.047 77.4
3 2.87 72.9 0.065 / 16 1.7 / 16 3.579 90.9
4 3.87 98.3 0.083 / 14 2.1 / 14 4.682 118.9
Table 10.8.6-7: Tri-Clamp dimensions