Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
chassis FL9.2
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
A91H2UH/A91H5UF/A91H9UF
091109
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
1-1 A91H2SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous
voltage. Such openings include, but are not TEST ALL EXPOSED
limited to, (1) spacing between the Liquid METAL SURFACES
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter ANY MEASUREMENTS NOT WITHIN THE
to the AC plug prongs tied together and touch LIMITS SPECIFIED HEREIN INDICATE A
the other ohmmeter lead in turn to each tuner POTENTIAL SHOCK HAZARD THAT MUST
antenna input exposed terminal screw and, if BE ELIMINATED BEFORE RETURNING THE
applicable, to the coaxial connector. If the INSTRUMENT TO THE CUSTOMER OR
measured resistance is less than 1.0 megohm BEFORE CONNECTING THE ANTENNA OR
or greater than 5.2 megohm, an abnormality ACCESSORIES.
exists that must be corrected before the
2. Read and comply with all caution and safety-
instrument is returned to the customer. Repeat
related notes on or inside the receiver cabinet, on
this test with the instrument AC switch in the off
the receiver chassis, or on the Liquid Crystal
position.
Panel.
2-1 LTVN_ISP
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2 LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area
Clearance d' d
AC Line Voltage Region
Distance (d), (d’)
U.S.A. or ≥ 3.2 mm
110 to 130 V
Canada (0.126 inches)
Fig. 1
Fig. 2
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 µF CAP. & 1.5 kΩ Exposed accessible
110 to 130 V i ≤ 0.5 mA rms
Canada RES. Connected in parallel parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4 LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)
Pin 1
10
3-1 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA
Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3-2 TVN_SN
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The “ I ” mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7
or
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3 TVN_SN
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
<Incorrect>
CBA
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4 TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
[42PFL3704D/F7(Serial No. : DS1A**********)]
1. Disassembly Flowchart Removal
This flowchart indicates the disassembly steps for the Step/ Remove/*Unhook/
cabinet parts, and the CBA in order to gain access to Loc. Part Fig. Unlock/Release/
No. Note
item(s) to be serviced. When reassembling, follow the No. Unplug/Unclamp/
steps in reverse order. Bend, route and dress the Desolder
cables as they were. Jack
[3] D2 (S-7) ---
Holder(D)
[1] Stand
Assembly 6(S-8), 4(S-9),
Digital Main D2
[4] *CN201, *CN202, ---
CBA Unit D5
[14] Junction *CN3901, Shield Box
[2] Rear Cabinet [13] Speaker(s)
CBA
Jack
[5] D2 (S-10) ---
[15] Function [16] IR Sensor
Holder(A)
CBA CBA
6(S-11), *CN203,
Jack Power D2
[6] *CN801, *CN802, ---
CBA D5
[3] Jack Holder [7] Inverter *CN901, *CN1501
(D) Power CBA
Inverter D2 8(S-12), *CN1601,
[7] ---
Power CBA D5 *CN1803, *CN1804
[4] Digital Main [8] Wall Mount
CBA Unit Bracket Wall Mount
[8] D3 4(S-13) ---
Bracket
[5] Jack Holder
(A) [9] PCB Holder D3 4(S-14) ---
AC Inlet
[6] Jack Power [10] D3 2(S-15) ---
CBA Holder
Stand 2(S-16), 2(S-17),
[11] D3 ---
[9] PCB Holder Bracket 4(S-18), 2(S-19)
LCD
[10] AC Inlet [12] Module D4 6(S-20) ---
Holder Assembly
4-1 A91H2DC
(3) Fig. No. showing procedure of part location * = Unhook, Unlock, Release, Unplug, or Desolder
(4) Identification of parts to be removed, unhooked, e.g. 2(S-2) = two Screws (S-2),
unlocked, released, unplugged, unclamped, or 2(L-2) = two Locking Tabs (L-2)
desoldered. (5) Refer to the following "Reference Notes in the
P = Spring, L = Locking Tab, S = Screw, Table."
H = Hex Screw, CN = Connector
(S-2)
(S-5)
(S-2)
(S-6)
(S-2)
(S-3)
(S-2)
(S-1)
Fig. D1
4-2 A91H2DC
[6] Jack Power CBA
(S-11) (S-10)
(S-11)
[4] Digital Main
CBA Unit [3] Jack Holder(D)
(S-9)
(S-7)
(S-12)
[7] Inverter
Power CBA
Shield Box
(S-8)
(S-12)
Fig. D2
4-3 A91H2DC
[9] PCB Holder
(S-16)
(S-18)
(S-17)
(S-14)
(S-19)
(S-16)
(S-17)
(S-19) (S-18)
(S-15)
4-4 A91H2DC
[17] Front Cabinet
[13] Speaker
Speaker Box [F]
(S-21)
(S-22)
[14] Junction
CBA (S-20)
[13] Speaker
(S-20)
Fig. D4
4-5 A91H2DC
TV Cable Wiring Diagram
To LCD Module
Assembly
CN1801 CN901
CN601
CN1501
CN801
CN802
WH301A
Junction
IR Sensor CBA CBA To LCD Module
Assembly
Fig. D5
4-6 A91H2DC
CABINET DISASSEMBLY INSTRUCTIONS
[42PFL3704D/F7(Serial No. : YA1A**********)]
1. Disassembly Flowchart Removal
This flowchart indicates the disassembly steps for the Step/ Remove/*Unhook/
cabinet parts, and the CBA in order to gain access to Loc. Part Fig. Unlock/Release/
No. Note
item(s) to be serviced. When reassembling, follow the No. Unplug/Unclamp/
steps in reverse order. Bend, route and dress the Desolder
cables as they were. Stand Sub
[3] D1 --------------- ---
[1] Stand Base Cover
Assembly
Rear 11(S-4), 2(S-5), (S-6),
[4] D1 ---
[3] Stand Sub
Cabinet (S-7)
[2] Stand Hinge
Cover
Jack
[5] D2 (S-8) ---
Holder(D)
[16] Junction
[4] Rear Cabinet [15] Speaker(s)
CBA 6(S-9), 4(S-10),
Digital Main D2
[6] *CN201, *CN202, ---
[17] Function [18] IR Sensor CBA Unit D5
*CN3901, Shield Box
CBA CBA
Jack
[7] D2 (S-11) ---
Holder(A)
[5] Jack Holder [9] Inverter
(D) Power CBA 6(S-12), *CN203,
Jack Power D2
[8] *CN801, *CN802, ---
[6] Digital Main [10] Wall Mount CBA D5
*CN901, *CN1501
CBA Unit Bracket
Inverter D2 8(S-13), *CN1601,
[9] ---
[7] Jack Holder Power CBA D5 *CN1803
(A)
Wall Mount
[10] D3 4(S-14) ---
[8] Jack Power Bracket
CBA
[11] PCB Holder D3 4(S-15) ---
[11] PCB Holder AC Inlet
[12] D3 2(S-16) ---
Holder
[12] AC Inlet Stand 2(S-17), 2(S-18),
Holder [13] D3 ---
Bracket 4(S-19)
[13] Stand LCD
Bracket [14] Module D4 6(S-20) ---
Assembly
[14] LCD Module
Assembly 4(S-21), 8(S-22),
[15] Speaker(s) D4 ---
Speaker Box(es)[F]
[19] Front
Cabinet Junction
[16] D4 Desolder ---
CBA
2. Disassembly Method [17]
Function
D4 *WH301A ---
CBA
Removal
IR Sensor
Step/ [18] D4 (S-23) ---
Remove/*Unhook/ CBA
Loc. Part Fig. Unlock/Release/
No. Note Front
No. Unplug/Unclamp/ [19] D4 --------------- ---
Desolder Cabinet
Stand Base ↓ ↓ ↓ ↓ ↓
[1] D1 4(S-1) --- (1) (2) (3) (4) (5)
Assembly
Stand
[2] D1 4(S-2), 2(S-3) ---
Hinge
4-7 A91H5DC
Note: desoldered.
(1) Order of steps in procedure. When reassembling, P = Spring, L = Locking Tab, S = Screw,
follow the steps in reverse order. These numbers H = Hex Screw, CN = Connector
are also used as the Identification (location) No. of * = Unhook, Unlock, Release, Unplug, or Desolder
parts in figures. e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(2) Parts to be removed or installed.
(5) Refer to the following "Reference Notes in the
(3) Fig. No. showing procedure of part location
Table."
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
(S-4)
(S-6)
(S-4)
(S-7)
(S-4)
(S-2)
(S-4)
(S-3)
(S-1)
Fig. D1
4-8 A91H5DC
[8] Jack Power CBA
(S-12) (S-11)
(S-12)
[6] Digital Main
CBA Unit [5] Jack Holder(D)
(S-10)
(S-8)
(S-13)
[9] Inverter
Power CBA
Shield Box
(S-9)
(S-13)
Fig. D2
4-9 A91H5DC
[11] PCB Holder
(S-17)
(S-18)
(S-19)
(S-15)
(S-17)
(S-19) (S-18)
(S-16)
4-10 A91H5DC
[19] Front Cabinet
[15] Speaker
Speaker Box [F]
(S-21)
(S-22)
[16] Junction
CBA (S-20)
[15] Speaker
(S-21)
(S-23)
[18] IR Sensor
Speaker Box [F] [14] LCD Module
CBA
Assembly
(S-20)
Fig. D4
4-11 A91H5DC
TV Cable Wiring Diagram
To LCD Module
Assembly
CN1801 CN901
CN601
CN1501
CN801
CN802
WH301A
Junction
IR Sensor CBA CBA To LCD Module
Assembly
Fig. D5
4-12 A91H5DC
CABINET DISASSEMBLY INSTRUCTIONS
[42PFL3704D/F7(Serial No. : YA2A**********)]
1. Disassembly Flowchart Removal
This flowchart indicates the disassembly steps for the Step/ Remove/*Unhook/
cabinet parts, and the CBA in order to gain access to Loc. Part Fig. Unlock/Release/
No. Note
item(s) to be serviced. When reassembling, follow the No. Unplug/Unclamp/
steps in reverse order. Bend, route and dress the Desolder
cables as they were. Stand Sub
[3] D1 --------------- ---
[1] Stand Base Cover
Assembly
Rear 11(S-4), 2(S-5), (S-6),
[4] D1 ---
[3] Stand Sub
Cabinet (S-7)
[2] Stand Hinge
Cover
Jack
[5] D2 (S-8) ---
Holder(D)
[16] Junction
[4] Rear Cabinet [15] Speaker(s)
CBA 6(S-9), 4(S-10),
Digital Main D2
[6] *CN201, *CN202, ---
[17] Function [18] IR Sensor CBA Unit D5
*CN3901, Shield Box
CBA CBA
Jack
[7] D2 (S-11) ---
Holder(A)
[5] Jack Holder [9] Inverter
(D) Power CBA 6(S-12), *CN203,
Jack Power D2
[8] *CN801, *CN802, ---
[6] Digital Main [10] Wall Mount CBA D5
*CN901, *CN1501
CBA Unit Bracket
Inverter D2 8(S-13), *CN1601,
[9] ---
[7] Jack Holder Power CBA D5 *CN1803, *CN1804
(A)
Wall Mount
[10] D3 4(S-14) ---
[8] Jack Power Bracket
CBA
[11] PCB Holder D3 4(S-15) ---
[11] PCB Holder AC Inlet
[12] D3 2(S-16) ---
Holder
[12] AC Inlet Stand 2(S-17), 2(S-18),
Holder [13] D3 ---
Bracket 4(S-19)
[13] Stand LCD
Bracket [14] Module D4 6(S-20) ---
Assembly
[14] LCD Module
Assembly 4(S-21), 8(S-22),
[15] Speaker(s) D4 ---
Speaker Box(es)[F]
[19] Front
Cabinet Junction
[16] D4 Desolder ---
CBA
2. Disassembly Method [17]
Function
D4 *WH301A ---
CBA
Removal
IR Sensor
Step/ [18] D4 (S-23) ---
Remove/*Unhook/ CBA
Loc. Part Fig. Unlock/Release/
No. Note Front
No. Unplug/Unclamp/ [19] D4 --------------- ---
Desolder Cabinet
Stand Base ↓ ↓ ↓ ↓ ↓
[1] D1 4(S-1) --- (1) (2) (3) (4) (5)
Assembly
Stand
[2] D1 4(S-2), 2(S-3) ---
Hinge
4-13 A91H9DC
Note: desoldered.
(1) Order of steps in procedure. When reassembling, P = Spring, L = Locking Tab, S = Screw,
follow the steps in reverse order. These numbers H = Hex Screw, CN = Connector
are also used as the Identification (location) No. of * = Unhook, Unlock, Release, Unplug, or Desolder
parts in figures. e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(2) Parts to be removed or installed.
(5) Refer to the following "Reference Notes in the
(3) Fig. No. showing procedure of part location
Table."
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
(S-4)
(S-6)
(S-4)
(S-7)
(S-4)
(S-2)
(S-4)
(S-3)
(S-1)
Fig. D1
4-14 A91H9DC
[8] Jack Power CBA
(S-12) (S-11)
(S-12)
[6] Digital Main
CBA Unit [5] Jack Holder(D)
(S-10)
(S-8)
(S-13)
[9] Inverter
Power CBA
Shield Box
(S-9)
(S-13)
Fig. D2
4-15 A91H9DC
[11] PCB Holder
(S-17)
(S-18)
(S-19)
(S-15)
(S-17)
(S-19) (S-18)
(S-16)
4-16 A91H9DC
[19] Front Cabinet
[15] Speaker
Speaker Box [F]
(S-21)
(S-22)
[16] Junction
CBA (S-20)
[15] Speaker
(S-21)
(S-23)
[18] IR Sensor
Speaker Box [F] [14] LCD Module
CBA
Assembly
(S-20)
Fig. D4
4-17 A91H9DC
TV Cable Wiring Diagram
To LCD Module
Assembly
CN1801 CN901
CN601
CN1501
CN801
CN802
WH301A
Junction
IR Sensor CBA CBA To LCD Module
Assembly
Fig. D5
4-18 A91H9DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for How to set up the service mode:
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Use the service remote control unit.
mechanical parts. It is important to perform 2. Turn the power on.
these adjustments only after all repairs and 3. Press the service button on the service remote
replacements have been completed. control unit. The following screen appears.
Also, do not attempt these adjustments unless
the proper equipment is available. "*" differs depending on the models.
Code : ***********-***
Test Equipment Required Pic code : **-***-**-*****-***
MIPS : Push 0key
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
2. Remote control unit
3. Color Analyzer
Tuner : ****-*****-****
How to make the Service remote Safety : safety_Non
control unit:
1. Prepare the MAGNAVOX remote control unit.
(Part No. NF800UD or NF802UD)
2. Cut “A” portion of the attached remote control unit
as shown in Fig. 1.
service button
(There is a button under the plastic housing.)
A Fig. 1
5-1 FL9.1PEA
1. Purity Check Mode 2. VCOM Adjustment
This mode cycles through full-screen displays of red, Test Point Adj. Point
green, blue, and white to check for non-active pixels.
[CHANNEL UP/DOWN ]
1. Enter the Service mode. Screen
buttons
2. Each time pressing [7] button on the service
remote control unit, the display changes as M. EQ. Spec.
follows. Color analyzer See below
Purity Check Mode Figure
White mode
To avoid interference from ambinent
[7] button light, this adjustment should be
performed in a dark room.
Perpendicularity
[7] button
Black mode
L = 3 cm
Color Analyzer
[7] button
Red mode 1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical
receptor to the center on the LCD-Panel surface
after zero point calibration as shown above.
Note: The optical receptor must be set
[7] button perpendicularly to the LCD Panel surface.
Green mode 3. Enter the Service mode.
4. Press [3] button on the service remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
service remote control unit so that the color
analyzer value becomes minimum.
[7] button
Blue mode
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
5-2 LC7NEA
The white balance adjustment should be 5. [CUTOFF]
performed when replacing the LCD Panel Press [1] button to select “COR” for Red Cutoff
adjustment. Press [3] button to select “COB” for
or Digital CBA.
Blue Cutoff adjustment.
[DRIVE]
3. White Balance Adjustment Press [4] button to select “DR” for Red Drive
Purpose: To mix red, green and blue beams correctly adjustment. Press [6] button to select “DB” for Blue
for pure white. Drive adjustment.
Symptom of Misadjustment: White becomes bluish 6. In each color mode, press [CHANNEL UP/DOWN]
or reddish. buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color
Test Point Adj. Point Mode Input temperature becomes 12000°K (x= 0.272 / y=
White Raster 0.278 ±0.005).
[VOLUME
[VIDEO1] (APL 70%)
Screen DOWN]
C/D or
button
(APL 40%)
M. EQ. Spec.
Pattern Generator, x= 0.272 ± 0.005
Color analyzer y= 0.278 ± 0.005
Figure
L = 3 cm
Low Hight
Light Light
100IRE 100IRE
40%=40IRE 70%=70IRE
5-3 LC7NEA
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
1. Turn the power on.
2. To enter the service mode, press the service
button on the service remote control unit.
- To cancel the service mode, press [POWER]
button on the service remote control unit.
3. Press [INFO] button on the service remote control
unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the
screen. "INITIALIZED" color will change to green
from red when initializing is complete.
6-1 A91F3INT
FIRMWARE RENEWAL MODE
Equipment Required The appearance shown in *1 is described as follows.
a. USB memory Appearance State
b. Remote Control Unit Downloading the firmware from
Downloading...
the USB memory.
Writing the downloaded firmware
Writing...
Firmware Update Procedure in flash memory.
Note: There are two states (the User Upgrade and Checking... Checking the new firmware.
the Factory Upgrade) in firmware update.
User Upgrade Upgrade the firmware only. 5. When the firmware update is completed, the
The setting values are not following will appear on the screen.
initialized.
Software Upgrade
Factory upgrade Upgrade the firmware and
initialize the setting values.
Rear Cabinet
*1 Downloading...
0%
7-1 A91H2FW
TROUBLESHOOTING
[ Power Supply Section ]
( Inverter Power CBA )
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F1601) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Check the presence that the primary component Check the presence that the rectifying diode or circuit
is leaking or shorted and service it if defective. is shorted in each rectifying circuit of secondary side,
and service it if defective.
Does the photocoupler circuit on the No Check D1213, D1720, IC1202, IC1704 and their
secondary side operate normally? periphery circuit, and service it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (D1101, D1714, D1715, Q1101)
8-1 A91H2TR
FLOW CHART NO.5
AL+5V is not output.
Is approximately +5V voltage supplied to the No Check C1103, D1101, D1102 and their periphery
cathode of D1101? circuit, and service it if defective.
Yes
Is approximately +5V voltage supplied to the collector No Check C1103, D1101, D1102 and their periphery
of Q1101? circuit, and service it if defective.
Yes
Is approximately +4V voltage supplied to the base No Check D1109 and their periphery circuit, and
of Q1101? service it if defective.
Yes
Replace Q1101.
Does the photocoupler circuit on the No Check D616, D637, IC601 and their periphery
secondary side operate normally? circuit, and service it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (D613, D615, D617, D618, D620, D621, D622, D623, D624, IC602, Q603, Q604, Q605)
Is approximately +40V voltage supplied to the No Check C617, D618, D619 and their periphery
cathode of D618? circuit, and service it if defective.
Yes
8-2 A91H2TR
FLOW CHART NO.10
P-ON+8.2V is not output.
No
Is approximately +16.5V voltage supplied to the Check C622, C624, D617, D624 and their periphery
collector of Q603? circuit, and service it if defective.
Yes
No
Is approximately +9V voltage supplied to the Check D627, D628 and their periphery circuit, and
base of Q603? service it if defective.
Yes
Replace Q603.
No
Is approximately +6V voltage supplied to the Check C619, D620 and their periphery circuit,
collector of Q604? and service it if defective.
Yes
No
Is approximately +6V voltage supplied to the Check D638 and their periphery circuit, and service
base of Q604? it if defective.
Yes
Replace Q604.
Replace Q605.
8-3 A91H2TR
[ Video Signal Section ]
FLOW CHART NO.1
The key operation is not functioning.
No
Are the contact point and installation state of the key Re-install the switches (SW351~SW355, SW357)
switches (SW351~SW355, SW357) normal? correctly or replace the poor switch.
Yes
No
When pressing each switches (SW351~SW355, Check the switches (SW351~SW355, SW357) and
SW357) do the voltage of Pin(3) of CN202 increase? their periphery, and service it if defective.
Yes
Replace Digital Main CBA Unit.
No
Is 3.3V voltage supplied to Pin(2) terminal of the Check AL+3.3V line and service it if defective.
remote control receiver (RS301)?
Yes
No
Is the "L" pulse sent out Pin(1) terminal of remote Replace the remote control receiver(RS301)
control receiver (RS301) when the infrared remote or the remote control unit.
control is activated?
Yes
No
Is the "L" pulse supplied to Pin(1) of CN202? Check the line between Pin(1) terminal of remote
Yes control receiver(RS301) and Pin(1) of CN202,
and service it if defective.
Replace Digital Main CBA Unit.
8-4 A91H2TR
FLOW CHART NO.3
Picture does not appear normally. (EXT. input)
No
Are the video signals inputted to each pin of IC401? Check the line between video input terminal and
each pin of IC401.
IC401 3PIN VIDEO-IN 1 IC401 3PIN → JK703 VIDEO-IN 1
IC401 1PIN Y-IN 1 IC401 1PIN → JK702 Y-IN 1
IC401 9PIN C-IN 1 IC401 9PIN → JK702 C-IN 1
IC401 7PIN VIDEO-IN 2 IC401 7PIN → JK707 VIDEO-IN 2
IC401 5PIN Y-IN 2 IC401 5PIN → JK706 Y-IN 2
IC401 11PIN C-IN 2 IC401 11PIN → JK706 C-IN 2
IC401 43PIN COMPONENT-Y-IN IC401 43PIN → JK717 COMPONENT-Y-IN
IC401 47PIN COMPONENT-Pb-IN IC401 47PIN → JK718 COMPONENT-Pb-IN
IC401 52PIN COMPONENT-Pr-IN IC401 52PIN → JK719 COMPONENT-Pr-IN
Yes
No
Are the video signals outputted to each pin of IC401? Is 5V voltage supplied to the Pin(2, 29, 33, 39, 44) of IC401?
Is 8.2V voltage supplied to the Pin(12) of IC401?
IC401 38PIN CVBS/Y/S-Y-IN
Yes No
IC401 36PIN Pb-IN
Replace IC401. Check P-ON+5V, P-ON+8.2V line
IC401 34PIN Pr/S-C-IN
and service it if defective.
Yes
Replace Digital Main CBA Unit or LCD Module
Assembly.
No
Are the DIF signal inputted to Pin(3, 4) of CN201? Check the line between Pin(3, 4) of CN201 and
Yes Pin(12, 13) of TU101, and service it if defective.
8-5 A91H2TR
[ Audio Signal Section ]
FLOW CHART NO.1
Picture does not appear normally. (EXT. input)
No
Are the audio(L/R) signals inputted to each pin of Check the line between audio input terminal and
IC401? each pin of IC401.
IC401 14,15PIN AUDIO(L/R)-IN 1 IC401 14,15PIN → JK704, JK705 AUDIO(L/R)-IN 1
IC401 16,17PIN AUDIO(L/R)-IN 2 IC401 16,17PIN → JK708, JK709 AUDIO(L/R)-IN 2
IC401 20,21PIN COMPONENT AUDIO(L/R)-IN IC401 20,21PIN → JK712, JK713 COMPONENT AUDIO(L/R)-IN
IC401 24,25PIN HDMI AUDIO(L/R)-IN IC401 24,25PIN → JK720, JK721 HDMI AUDIO(L/R)-IN
Yes
No
Are the audio(L/R) signals outputted to Pin(27, 28) of Is 5V voltage supplied to the Pin(2, 29, 33, 39, 44) of IC401?
IC401? Is 8.2V voltage supplied to the Pin(12) of IC401?
Yes Yes
Yes No
(Output to audio (Output to speakers)
output terminal) Replace IC401. Check P-ON+5V, P-ON+8.2V line
and service it if defective.
Are the audio(L/R) signals outputted to Pin(8, 10) of No Replace Digital Main CBA Unit or LCD Module
CN202? Assembly.
Yes
Are the audio(L/R) signals inputted to Pin(1, 44) No Check the line between Pin(8, 10) of CN202 and
of IC801? Pin(1, 44) of IC801, and service it if defective.
Yes
Are the audio(L/R) signals outputted to CN801 and No Check IC801 and their periphery circuit, and
CN802? service it if defective.
Yes
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Are the audio(L/R) signals outputted to Pin(4, 6) of No Replace Digital Main CBA Unit or LCD Module
CN202? Assembly.
Yes
No
Are the audio(L/R) signals inputted to Pin(3, 5) Check the line between Pin(4, 6) of CN202 and
of IC803? Pin(3, 5) of IC803, and service it if defective.
Yes
No
Are the audio(L/R) signals outputted to Pin(1, 7) Replace IC803
of IC803?
Yes
Check the line between Pin(1, 7) of IC803 and audio
output terminal(JK722, JK723) and service it if defective.
8-6 A91H2TR
FLOW CHART NO.2
Picture does not appear normally. (Tuner input)
No
Are the DIF signal inputted to Pin(3, 4) of CN201? Check the line between Pin(3, 4) of CN201 and
Yes Yes Pin(12, 13) of TU101, and service it if defective.
(Output to audio (Output to speakers)
output terminal)
Are the audio(L/R) signals outputted to Pin(8, 10) of No Replace Digital Main CBA Unit or LCD Module
CN202? Assembly.
Yes
Are the audio(L/R) signals inputted to Pin(1, 44) No Check the line between Pin(8, 10) of CN202 and
of IC801? Pin(1, 44) of IC801, and service it if defective.
Yes
Are the audio(L/R) signals outputted to CN801 and No Check IC801 and their periphery circuit, and
CN802? service it if defective.
Yes
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Are the audio(L/R) signals outputted to Pin(4, 6) of No Replace Digital Main CBA Unit or LCD Module
CN202? Assembly.
Yes
No
Are the audio(L/R) signals inputted to Pin(3, 5) Check the line between Pin(4, 6) of CN202 and
of IC803? Pin(3, 5) of IC803, and service it if defective.
Yes
No
Are the audio(L/R) signals outputted to Pin(1, 7) Replace IC803
of IC803?
Yes
Check the line between Pin(1, 7) of IC803 and audio
output terminal(JK722, JK723) and service it if defective.
8-7 A91H2TR
IC3301 RS301
JUNCTION
(MAIN MICRO CONTROLLER) REMOTE
CBA
SENSOR AL+3.3V
CN203 CN302 WH302A WH302B D302
2 REMOTE 7 2 REMOTE 2 POWER
5 P-ON-H1 4 5 P-ON-H1 5
6 KEY-IN1 3 6 KEY-IN1 6
CN3702 CN202
KEY-IN1 AC5 3 KEY-IN1 3
REMOTE R22 1 REMOTE 1
WH301A WH301B
KEY SWITCH 3 KEY-IN1 3
TO AUDIO
BLOCK AUDIO-MUTE TO
DIAGRAM AB9 AUDIO-MUTE PROTECT1 POWER SUPPLY 2
System Control Block Diagram
BLOCK DIAGRAM
CN3701 CN201
PROTECT1 AD5 10 PROTECT1 10 CN901 CN1801
P-ON-H2
P-ON-H2 AB13 6 P-ON-H2 6 4 P-ON-H2 8
P-ON-H1 TO
P-ON-H1 R23 8 P-ON-H1 8 3 P-ON-H1 9 POWER
PROTECT3
PROTECT3 AE5 7 PROTECT3 7 9 PROTECT3 3 SUPPLY 1
BACKLIGHT-SW BLOCK
9-1
BACKLIGHT-SW AB16 23 BACKLIGHT-SW 23 8 BACKLIGHT-SW 4 DIAGRAM
BACKLIGHT-ADJ
BACKLIGHT-ADJ AB23 25 BACKLIGHT-ADJ 25 7 BACKLIGHT-ADJ 5
IC3101 (MEMORY)
X3102
25MHz N1 CLKIN
OSC N2 CLKOUT
A91H2BLS
VIDEO SIGNAL AUDIO SIGNAL
IC401
JACK POWER CBA (INPUT SELECTOR) DIGITAL MAIN CBA UNIT
3
7
1
5
JK703
VIDEO-IN1 CN202 CN3702
9 CVBS/Y/S-Y-IN TO DIGITAL
38 18 CVBS/Y/S-Y-IN 18 SIGNAL
11 VIDEO Pb-IN
36 20 Pb-IN 20 PROCESS
SELECTOR Pr/S-C-IN BLOCK
34 22 Pr/S-C-IN 22 DIAGRAM
41
Video Block Diagram
C Y 43
JK702 WF3 WF2 WF1
S-VIDEO 45
-IN1 47
50
52
JK707
VIDEO-IN2
C Y
JK706
9-2
S-VIDEO
-IN2
51 S-VIDEO-SW1
49 S-VIDEO-SW2
WITH TWO COMPONENT INPUT
JK714
COMPONENT
-Y-IN1
JK715
COMPONENT
-Pb-IN1
JK716
COMPONENT
-Pr-IN1
JK717
COMPONENT
-Y-IN2
JK718
COMPONENT
-Pb-IN2
JK719
COMPONENT
-Pr-IN2
TU101
(TUNER UNIT)
CN201 CN3701
DIF-OUT1 TO DIGITAL
DIF-OUT1 12 3 DIF-OUT1 3 SIGNAL
DIF-OUT2
DIF-OUT2 13 4 DIF-OUT2 4 PROCESS
IF-AGC BLOCK
IF-AGC 14 1 IF-AGC 1 DIAGRAM
A91H2BLV
AUDIO SIGNAL
JK705 14
AUDIO(R)-IN1
16
18 WF4
20
JK708 TO
AUDIO(L)-IN2 24 CN202 CN3702 DIGITAL
AUDIO(L)
28 24 AUDIO(L) 24 SIGNAL
AUDIO(R) PROCESS
JK709 AUDIO 26 AUDIO(R) 26
SELECTOR BLOCK
AUDIO(R)-IN2 DIAGRAM
15
Audio Block Diagram
JK710 17
COMPONENT 19
AUDIO(L)-IN1 27
21
JK711 25
COMPONENT
AUDIO(R)-IN1
WITH TWO COMPONENT INPUT
JK712
COMPONENT
AUDIO(L)-IN2
JK713 TO
COMPONENT SYSTEM
AUDIO(R)-IN2 AUDIO-MUTE CONTROL
BLOCK
DIAGRAM
JK720
HDMI
AUDIO(L)-IN
9-3
JK721
HDMI IC3503 IC3501
AUDIO(R)-IN IC803 (AUDIO D/A CONVERTER) (AUDIO DSP)
(OP AMP) LRCLK
CN202 CN3702 8 35 2
(L-CH) BCLK
JK722 7 5 4 AUDIO(L)-OUT 4 15 7 36 40
AUDIO(L)-OUT (R-CH) D/A ADATA1
6 AUDIO(R)-OUT 6 14 CONVERTER 6 33 DSP 4
ACLK
8 AMP(L)-OUT 8 5 37 39
JK723 1 3 ADATA0 TO
AUDIO(R)-OUT Q703 10 AMP(R)-OUT 10 34 3
IC3502 DIGITAL
MUTE SIGNAL
(AUDIO D/A CONVERTER)
Q704 Q802,Q804 PROCESS
BLOCK
MUTE DRIVE 8 DIAGRAM
JK701 (L-CH)
15 7
DIGITAL Q702 CN202 CN3702 (R-CH) D/A
14 CONVERTER 6
AUDIO-OUT
(COAXIAL) BUFFER 13 SPDIF 13 5
11 AUDIO-MUTE 11
IC801 (AUDIO POWER AMP)
SPDIF
9,10
DRIVE1 PWM1 1
13,14
CL801 CN801
SP801 SP(L)+ 2
SPEAKER
L-CH SP(L)- 1
35,36
DRIVE2 PWM2 44
31,32
MUTE CONTROL
CL802 CN802
SP802 SP(R)+ 2 20
SPEAKER Q801
SP(R)- 1
R-CH
A91H2BLA
VIDEO SIGNAL AUDIO SIGNAL LCD MODULE
ASSEMBLY
V2
AA3
U3 A/D
CVBS/Y/S-Y-IN SW
U1 CONVERTER
Pb-IN
V1
Pr/S-C-IN
U2
V3 CN3901
TO VIDEO
BLOCK DIAGRAM AD23 23 LVDS-D0E(+)
DIF-OUT1 AD24 24 LVDS-D0E(-)
AE2 DEMODULATOR
DIF-OUT2 AE23 21 LVDS-D1E(+)
AF2 /MPEG DECODER
AF23 22 LVDS-D1E(-)
IF-AGC
AF7 IF-AGC AF22 19 LVDS-D2E(+)
AE22 20 LVDS-D2E(-)
IC3801 (HDMI SW) AD21 13 LVDS-D3E(+)
DATA0(+) AD22 14 LVDS-D3E(-)
7 22 AUDIO(L) AF24 16 LVDS-CE(+)
DATA0(-) M1
9 21 AUDIO(R) AE24 17 LVDS-CE(-)
DATA1(+) M2 LVDS
4 24 BCLK AF18 39 LVDS-D0O(+)
DATA1(-) AD9 TX
6 23 TO AUDIO LRCLK AE18 40 LVDS-D0O(-)
DATA2(+) AD12
1 26 BLOCK DIAGRAM
JK3803 DATA2(-) ACLK AUDIO I/F AD17 37 LVDS-D1O(+)
HDMI-IN1 3 25 AD10
CLOCK(+) SPDIF AD18 38 LVDS-D1O(-)
10 20 AD11
CLOCK(-) ADATA0 AE17 35 LVDS-D2O(+)
12 19 AC10
HDMI-DATA ADATA1 AF17 36 LVDS-D2O(-)
AD14
Digital Signal Process Block Diagram
16 43
9-4
HDMI-CLOCK AF16 29 LVDS-D3O(+)
15 44 AE16 30 LVDS-D3O(-)
AE19 32 LVDS-CO(+)
DATA0(+) AUDIO AF19 33 LVDS-CO(-)
7 14 DECODER
DATA0(-)
9 13 56 D1
DATA1(+) DIGITAL
4 16 57 D2
DATA1(-) SIGNAL
6 15 58 C1 PROCESS
DATA2(+)
JK3801 1 18 HDMI 59 C2 HDMI
DATA2(-)
HDMI-IN2 3 17 SW 60 B1 I/F
CLOCK(+)
10 12 61 B2
CLOCK(-)
12 11 62 A1
HDMI-DATA
16 39 63 A2
HDMI-CLOCK
15 40 VIDEO
DECODER
IC3201
(DDR2 SDRAM)
DATA0(+)
7 68
DATA0(-) A13-15,A18, B1,B9,C2,C8,
9 67 D1,D3,D7,D9,
DATA1(+) A21-23,B13-15,
4 70 B17,B19-23 F1,F9,G2,G8, DATA(0-15)
DATA1(-) H1,H3,H7,H9
6 69
DATA2(+) C15,C17-19, M2,M3,M7,M8,
JK3802 1 72 C23,C24,D14, N2,N3,N7,N8, ADDESS(0-12)
DATA2(-) D15,D17-19,
HDMI-IN3 3 71 P2,P3,P7,P8,R2
CLOCK(+) D22,D23
10 66
CLOCK(-)
12 65
HDMI-DATA
16 29
HDMI-CLOCK
15 30
A91H2BLD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F1601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.
AC601
AC CORD AC F1601 L1601 INVERTER POWER CBA D1205-D1208 T1201
INLET CN1601 8A/250V Q1101
1 ACL LINE BRIDGE 4 10 +3.3V REG. AL+3.3V
2 HOT-GND FILTER RECTIFIER
9
L1602 D1601
Q1203 6 7
LINE BRIDGE
SWITCHING 1
FILTER RECTIFIER
L1604
IC1202
IC1401 2 11 (FEED BACK)
(SWITCHING CONTROL)
Q1602 Q1204 4 1
7 14 SWITCHING 5 8 SWITCHING
3 2
CONTROL
L1603
SWITCHING
Power Supply 1 Block Diagram
CONTROL 2 11
Q1601 Q1202
8 11 SWITCHING 5 8
RL1201
VCC
12 16 1 Q1201
CN1501
9-5
TO POWER
SUPPLY 2 +354V 1
BLOCK HOT+22V 4 T1701
DIAGRAM LCD MODULE
CN601 IC1702 8 9
(HIGH-VOLTAGE ASSEMBLY
CN1804
RESONANT CONTROL)
7 10 1-5 PANEL+24V
Q1701
9 SWITCHING 11
CN1803
5 12 1-5 PANEL+24V
8 11 PROTECT3
4 13 13 BACKLIGHT-ADJ
Q1702 14 BACKLIGHT-SW
12 SWITCHING 3 14
2 15
HIGH- 5
VOLTAGE
1 16
HOT RESONANT
CONTROL IC1704
4 (FEED BACK)
13 4 1 BACKLIGHT-SW
BACKLIGHT-ADJ
[42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
A91H2BLP1
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F1601) is blown , check to see that all components in the power supply replace only with same type 4 A, 125V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 4A/125V ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Otherwise it may cause some components in the power supply circuit to fail.
AC601
AC CORD AC F1601 L1601 INVERTER POWER CBA D1205-D1208 T1201
INLET CN1601 8A/250V Q1101
1 ACL LINE BRIDGE 4 10 +3.3V REG. AL+3.3V
2 HOT-GND FILTER RECTIFIER
9
L1602 D1601
Q1203 6 7
LINE BRIDGE
SWITCHING 1
FILTER RECTIFIER
L1604
IC1202
IC1401 2 11 (FEED BACK)
(SWITCHING CONTROL)
Q1602 Q1204 4 1
7 14 SWITCHING 5 8 SWITCHING
3 2
CONTROL
L1603
SWITCHING
CONTROL 2 11
Q1601 Q1202
8 11 SWITCHING 5 8
RL1201
VCC
12 16 1 Q1201
CN1501
9-6
TO POWER
SUPPLY 2 +354V 1
BLOCK HOT+22V 4 T1701
DIAGRAM LCD MODULE
CN601 IC1702 8 9
(HIGH-VOLTAGE ASSEMBLY
CN1804
RESONANT CONTROL)
7 10 1-5 PANEL+24V
Q1701
9 SWITCHING 11
CN1803
5 12 1-5 PANEL+24V
8 14 PROTECT3
4 13 11,13 BACKLIGHT-ADJ
Q1702 12 BACKLIGHT-SW
12 SWITCHING 3 14
2 15
HIGH- 5
VOLTAGE
1 16
HOT RESONANT
CONTROL IC1704
4 (FEED BACK)
13 4 1 BACKLIGHT-SW
BACKLIGHT-ADJ
3 3 2 PROTECT3 TO SYSTEM CONTROL
P-ON-H1 BLOCK DIAGRAM
Q1401 IC1705
Q1703 (ISOLATOR) P-ON-H2
14 4 1
Q1707
Q1402 Q1704 3 2 Q1708
IC1705
(ISOLATOR)
4 1
Q1705
Q1403 3 2 COLD
Q1404
Power Supply 1 Block Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
A91H5BLP1
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
T601
2 9 AL+13V
Q603 P-ON+11V
SW+8.2V P-ON+8.2V
TUNER+31V
10
P-ON+5V
P-ON+3.3V
3
TO
POWER CN601 16
SUPPLY 1 1 +345V
BLOCK
DIAGRAM 2 HOT-GND
CN1501 3 HOT+22V
11
DIGITAL MAIN CBA UNIT
4 CN201 CN3701
Power Supply 2 Block Diagram
9-7
7
13
Q605
SW+3.3V
Q601 8 12
SWITCHING
TO SYSTEM
PROTECT1 CONTROL
IC601 (FEED BACK) BLOCK
DIAGRAM
4 1
Q602
SWITCHING
3 2
CONTROL
HOT COLD
JACK POWER CBA
A91H2BLP2
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10-6 µF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire FL9.2 chasis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the FL9.2 chasis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chasis at the
moment of making this service manual.
Depend on the mass production date of each
model, the acutual layout of each Board may differ
slightly from this version.
10-1 FL9_2PSC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
1 2 3
(Unit: Volt) 5.0 5.0 Power on mode
10-2 FL9_2PSC
Jack Power 1/3 Schematic Diagram
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-3 A91H2SCJP1
Jack Power 2/3 Schematic Diagram
10-4 A91H2SCJP2
Jack Power 3/3 Schematic Diagram
10-5 A91H2SCJP3
Inverter Power 1/3 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
CAUTION ! NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F1601) is blown , check to see that all components in the power supply replace only with same type 8A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 8A 250V ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
10-6 A91H2SCIP1
Inverter Power 2/3 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-7 A91H2SCIP2
Inverter Power 3/3 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-8 A91H2SCIP3
Inverter Power 1/3 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F1601) is blown , check to see that all components in the power supply replace only with same type 8A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 8A 250V ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
10-9 A91H5SCIP1
Inverter Power 2/3 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-10 A91H5SCIP2
Inverter Power 3/3 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-11 A91H5SCIP3
IR Sensor, Function & Junction Schematic Diagram
10-12 A91H2SCIR
Digital Main 1/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-13 A91H2SCD1
Digital Main 2/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-14 A91H2SCD2
Digital Main 3/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-15 A91H2SCD3
Digital Main 4/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-16 A91H2SCD4
Digital Main 5/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-17 A91H2SCD5
Digital Main 1/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-18 A91H5SCD1
Digital Main 2/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-19 A91H5SCD2
Digital Main 3/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-20 A91H5SCD3
Digital Main 4/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-21 A91H5SCD4
Digital Main 5/5 Schematic Diagram [42PFL3704D/F7 (Serial No. : YA1A**********)]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-22 A91H5SCD5
Jack Power CBA Top View
10-23 BA94H0F01012-A
Jack Power CBA Bottom View
WF4
PIN 24 OF
CN202
WF3
PIN 22 OF
CN202
WF2
PIN 20 OF
CN202
WF1
PIN 18 OF
CN202
10-24 BA94H0F01012-A
Inverter Power CBA Top View [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
Because a hot chassis ground is present in the power supply
CAUTION ! circuit, an isolation transformer must be used when repairing.
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly,
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F1601) is blown , check to see that all components in the power supply when troubleshooting this type of power supply circuit,
replace only with same type 8A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 8A 250V a variable isolation transformer is required.
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-25 BA94H0F01033-A
Inverter Power CBA Bottom View [42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
Because a hot chassis ground is present in the power supply
CAUTION ! circuit, an isolation transformer must be used when repairing.
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly,
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F1601) is blown , check to see that all components in the power supply when troubleshooting this type of power supply circuit,
replace only with same type 8A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 8A 250V a variable isolation transformer is required.
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-26 BA94H0F01033-A
Inverter Power CBA Top View [42PFL3704D/F7 (Serial No. : YA1A**********)]
Because a hot chassis ground is present in the power supply
CAUTION ! circuit, an isolation transformer must be used when repairing.
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly,
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F1601) is blown , check to see that all components in the power supply when troubleshooting this type of power supply circuit,
replace only with same type 8A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 8A 250V a variable isolation transformer is required.
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-27 BA91H5F01031-A
Inverter Power CBA Bottom View [42PFL3704D/F7 (Serial No. : YA1A**********)]
Because a hot chassis ground is present in the power supply
CAUTION ! circuit, an isolation transformer must be used when repairing.
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly,
CAUTION ! : For continued protection against risk of fire,
If Main Fuse (F1601) is blown , check to see that all components in the power supply when troubleshooting this type of power supply circuit,
replace only with same type 8A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 8A 250V a variable isolation transformer is required.
ATTENTION : Utiliser un fusible de rechange de même type de 8A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-28 BA91H5F01031-A
Function CBA Top View IR Sensor CBA Top View
BA94H0F01012-C
BA94H0F01012-B BA94H0F01012-D
10-29
WAVEFORMS
(S-VIDEO IN)
(COMPONENT IN)
(COMPONENT IN)
11-1 A91H2WF
WIRING DIAGRAM
[42PFL3704D/F7 (Serial No. : DS1A**********, YA2A**********)]
CN202 CL202 CN3702
CONNECTOR-3
1 REMOTE 1
S-VIDEO
2 LED1 2
FUNCTION CBA
-IN1
3 KEY-IN1 3
HDMI-
S-VIDEO 4 AUDIO(L)-OUT 4
-IN2
5 GND 5
VIDEO 6 AUDIO(R)-OUT 6
CONNECTOR-2
-IN1
WH301A
7 GND 7
AUDIO(L) 8 AMP(L)-OUT 8
-IN1
9 GND 9
1
2
3
4
HDMI-
AUDIO(R) 10 AMP(R)-OUT 10
-IN1 11 AUDIO-MUTE 11
CL301
12 GND 12
AL+3.3V
KEY-IN1
KEY-IN2
CONNECTOR-1
VIDEO
-IN2 13 SPDIF 13
GND
14 GND 14
AUDIO(L) 15 AL+3.3V 15
-IN2
HDMI-
WH301B
1
2
3
4
16 AL+3.3V 16
IR SENSOR CBA
AUDIO(R) 17 GND 17
-IN2
18 CVBS/Y/S-Y-IN 18
19 GND 19 CN3902
TO USB JACK
AUDIO(L)
-OUT 20 Pb-IN 20 1 USB+5V
WH302B
21 GND 21 2 USB(-)
AUDIO(R) 3 USB(+)
-OUT 22 Pr/S-C-IN 22
23 GND 23 4 GND
1
2
3
4
5
6
7
8
DIGITAL 24 AUDIO(L) 24
-AUDIO-OUT
25 GND 25
CL302
COMPONENT
DVD-LED
REMOTE
P-ON-H1
26 AUDIO(R) 26
AL+3.3V
KEY-IN1
KEY-IN2
-AUDIO(L)-IN2
LED1
27 SDA 27
GND
CN3901 CL3901
COMPONENT 28 SCL 28 1 LCD+12V
-AUDIO(R)-IN2
29 GND 29 2 LCD+12V
WH302A
1
2
3
4
5
6
7
8
JUNCTION CBA
COMPONENT 3 LCD+12V
-Y-IN2 CN201 CL201 CN3701
4 LCD+22V
1 IF-AGC 1
COMPONENT 5 GND
2 GND 2
-Pb-IN2 6 GND
3 DIF-OUT1 3
JACK POWER CBA
7 GND
COMPONENT 4 DIF-OUT2 4
CN302
-Pr-IN2 8 GND
10 NU
-AUDIO(L)-IN 7 PROTECT3 7
11 NU
8 P-ON-H1 8
HDMI 12 NU
DVD-LED
9 PROTECT2 9
REMOTE
P-ON-H1
-AUDIO(R)-IN
AL+3.3V
KEY-IN1
KEY-IN2
13 LVDS-D3E(+)
10 PROTECT1 10
LED1
GND
14 LVDS-D3E(-)
11 RESET 11
15 GND
12 GND 12
16 LVDS-CE(+)
CN203
1
2
3
4
5
6
7
8
13 GND 13
17 LVDS-CE(-)
14 P-ON+5V 14
18 GND
15 P-ON+3V 15
19 LVDS-D2E(+)
16 P-ON+3V 16
TUNER UNIT
20 LVDS-D2E(-)
17 GND 17
21 LVDS-D1E(+)
18 P-ON+7V 18
22 LVDS-D1E(-)
19 GND 19
28 LCD+12V 28
32 LVDS-CO(+)
SP(R)+
SP(L)+
CN801
CN802
SP(R)-
+345V
SP(L)-
29 LCD+12V 29
CN601
CN901
33 LVDS-CO(-)
34 GND
10
11
1
2
3
4
5
6
7
8
9
35 LVDS-D2O(+)
1
2
3
1
2
1
2
BACKLIGHT-ADJ
BACKLIGHT-SW
POWER-RESET
36 LVDS-D2O(-)
CL801
CL802
PROTECT3
CL901
37 LVDS-D1O(+)
P-ON-H1
P-ON-H2
AL+5V
AL+5V
38 LVDS-D1O(-)
GND
GND
GND
39 LVDS-D0O(+)
1
2
3
4
40 LVDS-D0O(-)
11
10
CN1501
CN1801
9
8
7
6
5
4
3
2
1
NU
+345V
NU
HOT-GND
HOT+22V
41
SPEAKER
SPEAKER
42 NU
SP801
SP802
R-CH
L-CH
43 GND
POWER CBA
44 P-ON+3.3V
INVERTER
45 NU
46 NU
47 NU
48 NU
49 NU
CN1601
CN1803
CN1804
50 NU
51 NU
10
11
12
13
14
10
1
2
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PANEL+24V
PANEL+24V
PANEL+24V
PANEL+24V
PANEL+24V
GND
GND
GND
GND
GND
PROTECT3
NU
BACKLIGHT-ADJ
BACKLIGHT-SW
PANEL+24V
PANEL+24V
PANEL+24V
PANEL+24V
PANEL+24V
GND
GND
GND
GND
GND
CL1803
CL1804
INLET
AC
AC CORD
AC601
12-1 A91H2WI
WIRING DIAGRAM [42PFL3704D/F7 (Serial No. : YA1A**********)]
CN202 CL202 CN3702
CONNECTOR-3
1 REMOTE 1
S-VIDEO
2 LED1 2
FUNCTION CBA
-IN1
3 KEY-IN1 3
HDMI-
S-VIDEO 4 AUDIO(L)-OUT 4
-IN2
5 GND 5
VIDEO 6 AUDIO(R)-OUT 6
CONNECTOR-2
-IN1
WH301A 7 GND 7
AUDIO(L) 8 AMP(L)-OUT 8
-IN1
9 GND 9
1
2
3
4
HDMI-
AUDIO(R) 10 AMP(R)-OUT 10
-IN1 11 AUDIO-MUTE 11
CL301
12 GND 12
AL+3.3V
KEY-IN1
KEY-IN2
CONNECTOR-1
VIDEO
-IN2 13 SPDIF 13
GND
14 GND 14
AUDIO(L) 15 AL+3.3V 15
-IN2
HDMI-
WH301B
1
2
3
4
16 AL+3.3V 16
IR SENSOR CBA
AUDIO(R) 17 GND 17
-IN2
18 CVBS/Y/S-Y-IN 18
19 GND 19 CN3902
TO USB JACK
AUDIO(L)
-OUT 20 Pb-IN 20 1 USB+5V
WH302B
21 GND 21 2 USB(-)
AUDIO(R) 3 USB(+)
-OUT 22 Pr/S-C-IN 22
23 GND 23 4 GND
1
2
3
4
5
6
7
8
DIGITAL 24 AUDIO(L) 24
-AUDIO-OUT
25 GND 25
CL302
COMPONENT
DVD-LED
REMOTE
P-ON-H1
26 AUDIO(R) 26
AL+3.3V
KEY-IN1
KEY-IN2
-AUDIO(L)-IN2
LED1
27 SDA 27
GND
CN3901 CL3901
COMPONENT 28 SCL 28 1 LCD+12V
-AUDIO(R)-IN2
29 GND 29 2 LCD+12V
WH302A
1
2
3
4
5
6
7
8
JUNCTION CBA
COMPONENT 3 LCD+12V
-Y-IN2 CN201 CL201 CN3701
4 LCD+22V
1 IF-AGC 1
COMPONENT 5 GND
2 GND 2
-Pb-IN2 6 GND
3 DIF-OUT1 3
JACK POWER CBA
7 GND
COMPONENT 4 DIF-OUT2 4
CN302
-Pr-IN2 8 GND
10 NU
-AUDIO(L)-IN 7 PROTECT3 7
11 NU
8 P-ON-H1 8
HDMI 12 NU
DVD-LED
9 PROTECT2 9
REMOTE
P-ON-H1
-AUDIO(R)-IN
AL+3.3V
KEY-IN1
KEY-IN2
13 LVDS-D3E(+)
10 PROTECT1 10
LED1
GND
14 LVDS-D3E(-)
11 RESET 11
15 GND
12 GND 12
16 LVDS-CE(+)
CN203
1
2
3
4
5
6
7
8
13 GND 13
17 LVDS-CE(-)
14 P-ON+5V 14
18 GND
15 P-ON+3V 15
19 LVDS-D2E(+)
16 P-ON+3V 16
TUNER UNIT
20 LVDS-D2E(-)
17 GND 17
21 LVDS-D1E(+)
18 P-ON+7V 18
22 LVDS-D1E(-)
19 GND 19
28 LCD+12V 28
32 LVDS-CO(+)
SP(R)+
SP(L)+
CN801
CN802
SP(R)-
1 +345V
SP(L)-
29 LCD+12V 29
CN601
CN901
33 LVDS-CO(-)
34 GND
10
11
1
2
3
4
5
6
7
8
9
35 LVDS-D2O(+)
1
2
1
2
BACKLIGHT-ADJ
BACKLIGHT-SW
POWER-RESET
36 LVDS-D2O(-)
CL801
CL802
PROTECT3
CL901
37 LVDS-D1O(+)
P-ON-H1
P-ON-H2
AL+5V
AL+5V
38 LVDS-D1O(-)
GND
GND
GND
39 LVDS-D0O(+)
1
2
3
4
40 LVDS-D0O(-)
11
10
CN1501
CN1801
9
8
7
6
5
4
3
2
1
GND
+345V
NU
HOT-GND
HOT+22V
41
SPEAKER
SPEAKER
42 P-ON+3.3V
SP801
SP802
R-CH
L-CH
43 BACKLIGHT-ADJ
POWER CBA
44 BACKLIGHT-ADJ
INVERTER
45 NU
46 NU
47 NU
48 NU
49 NU
CN1601
CN1803
50 NU
51 P-ON+3.3V
10
11
12
13
14
1
2
1
2
3
4
5
6
7
8
9
PANEL+24V
PANEL+24V
PANEL+24V
PANEL+24V
PANEL+24V
GND
GND
GND
GND
GND
ANALOG DIMMING
BACKLIGHT-SW
BACKLIGHT-ADJ
PROTECT3
CL1803
INLET
AC
AC CORD
AC601
12-2 A91H5WI
EXPLODED VIEWS
Cabinet [42PFL3704D/F7 (Serial No. : DS1A**********)]
A1
A4
L2
A21 CL801
SP801 L1 L1 L1
B10
Function CBA CL1803
A7 L2
A29 CL1804 L7
L1
B27
L2 Junction CBA
L5
CL802 L1
B3 A6
B27
S5
SP802 Jack Power CBA
L1 L4 L1
A23
A11 L3 B5 L6
CL302 L2
CL301
L1
IR Sensor CBA B10 B2
LCD-1 L8 L1
L4 CL901
L1 L8 B21 AC601
L3 L3
L6 B24
CL1601 L4
L1 L3
L4 FC1601 CL202 L3
L1 B6
L6 CL201 B13
B9 L5
L3 L3
CL3901 Stand Assembly
B23
B1 L8
Digital Main CBA Unit X3301
B4
L4 L5
B22 L6
Inverter Power CBA
L3 B21
L8 B20
L8
See Electrical Parts List
for parts with this mark.
13-1 A91H2CEX
Cabinet [42PFL3704D/F7 (Serial No. : YA1A**********)]
A1
A4
L2
A21 CL801
SP801 L1 L1 L1
B10
Function CBA CL1803
A7 L2
A29 B32-2 L7
L1
B27 B32-1 B32-1
L2 Junction CBA
L5
CL802 L1
B3 A6
B27
S5
SP802 Jack Power CBA
L1 L4 L1
A23
A11 L3 B5 L6
B32-1 L2
IR Sensor CBA L1 B32-2
CL302 L1
B2
B10 LCD-1 L8 L1
L4 CL901 B8
L2 L8 AC601
B21
L1 L3
B24 A24
CL1601 L4
L1
L4 L2 CL202 L3 L2
L1 B31 B13 B6
CL201
B9 L5
L3 L3
CL3901
B23 Stand Base Assembly
B1 L8 Digital Main CBA Unit
X3301
B4
L4 L5
Inverter Power CBA B22 X5
L3 B21
L8 B20
L8
See Electrical Parts List
for parts with this mark.
13-2 A91H5CEX
Cabinet [42PFL3704D/F7 (Serial No. : YA2A**********)]
A1
A4
L2
CL801
SP801 L1 L1 L1
B10
Function CBA CL1803
A7 L2
A29 CL1804 L7
L1
B27
L2 Junction CBA
L5
CL802 L1
B3 A6
B27
S5
SP802 Jack Power CBA
L1 L4 L1
A23
A11 L3 B5 L6
CL302 L2
CL301
L1
IR Sensor CBA B10 B2
LCD-1 L8 L1 B8
L4 CL901
L1 L8 B21 AC601
L3 L3 A24
L6 B24
CL1601 L4
L1 L3
L4 CL202 L3 L2
L1 B31 B6
L6 CL201 B13
B9 L5
L3 L3
CL3901
B23 Stand Base Assembly
B1 L8
Digital Main CBA Unit X3301
B4
L4 L5
B22
Inverter Power CBA X5
L3 B21
L8 B20
L8
See Electrical Parts List
for parts with this mark.
13-3 A91H9CEX
Packing [42PFL3704D/F7(Serial No. : DS1A**********)]
S12
AC601 X5
RMD-1
Tape
X4
S2
X1
S6
S5
Stand
Assembly
S4
X13
Packing Tape
S3
Packing Tape
Packing Tape
FR
ON
T
S13
S5
PP Band
13-4 A91H2PEX
Packing [42PFL3704D/F7(Serial No. : YA1A**********, YA2A**********)]
X5
X2 X14 X6 X21 X4 Carton Sealing Tape
S5
S5
S12
S2
S5
Stand Base
Assembly
Carton Sealing Tape
X13
S4
S3
FR
ON
T
S13
S5
Strapping Strip
13-5 A91H5PEX
MECHANICAL PARTS LIST
[42PFL3704D/F7 (Serial No. : DS1A**********)]
PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No.
# have special characteristics important to safety. S13 CARTON(L) A91H2UH 1EM325780
Before replacing any of these components, read ACCESSORIES
carefully the product safety notice in this service AC601# AC CORD WITH A GND WIRE UL/CSA/ 162/ WAV0162LW001
NO/BLACK
manual. Don't degrade the safety of the product
RMD-1 REMOTE CONTROL TRANSMITTER YKF259- URMT34JHG001
through improper servicing. 001
X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
NOTE: Parts that are not assigned part numbers
X2# OWNERS MANUAL A91H2UH 1EMN24524
(---------) are not available.
X4 BATTERY R03-B500/01S XB0M451CZB01
X5 STAND SCREW KIT(LC7-42W) A91H2UH 1ESA20029
X6 QUICK START GUIDE A91H2UH 1EMN24525
Ref. No. Description Part No.
X13 CONNECTION GUIDE A91H2UH 1EM325957
STAND ASSEMBLY A91H2UH 1ESA20027 X14 CHILD SAFETY SHEET A91H2UH 1EMN24526
A1 FRONT CABINET A91H2UH 1EM023506 X18 WALL MOUNT INSTRUCTION A91H2UH 1EMN24527
A4 REAR CABINET A91H2UH 1EM023507 X20 CABLE MANAGEMENT TIE A91H2UH 1EM428657
A6# RATING LABEL A91H2UH ---------- X21 REGISTRATION CARD(PHILIPS) A91H2UH 1EMN24599
A7 FUNCTION KNOB A91H2UH 1EM222865 X3301 THERMOSTAR TMS-L-2 (24*24HC) XK10000X4002
A11 SENSOR LED LENS A91H2UH 1EM325697
A21 POP LABEL A91H2UH ----------
A23 ENERGY STAR LABEL A91H2UH ----------
A29 KNOB FRAME A91H2UH 1EM222866
B1 WALL MOUNT BRACKET A91H2UH 1EM023510
B2 STAND BRACKET A91H2UH 1EM023511
B3 PCB HOLDER A91H2UH 1EM023509
B4 SHIELD BOX A91H2UH 1EM222869
B5 JACK HOLDER(A) A91H2UH 1EM222863
B6 JACK HOLDER(D) A91H2UH 1EM222864
B9 AC INLET HOLDER A91H2UH 1EM325698
B10 SPEAKER BOX(F) A91H2UH 1EM123354
B13 GASKET A91H2UH 1EM428597
B27 CLOTH(10X180XT0.5) L0336JG 0EM408827
CL201 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94H0-101
CL202 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94H0-101
CL801 WIRE ASSEMBLY 2PIN 2PIN 500MM WX1A94H0-205
CL802 WIRE ASSEMBLY 2PIN 2PIN 750MM WX1A94H0-206
CL901 FFC WIRE ASSEMBLY 11PIN 11PIN 90MM WX1A94H0-104
CL1601 WIRE ASSEMBLY 2PIN 2PIN 220MM WX1A94H0-204
CL1803 WIRE ASSEMBLY 14PIN 14PIN 510MM WX1A94H0-201
CL1804 WIRE ASSEMBLY 10PIN 10PIN 580MM WX1A94H0-202
CL3901 WIRE ASSEMBLY 51PIN 51PIN 240MM WX1A94H0-301
FC1601 CLAMP FILTER ZCAT2035-0930A XL06035TE001
L1 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140
L2 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100
L3 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392A
L4 DOUBLE SEMS SCREW M4X6 M4X6 FPJ34060
L5 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080
L6 DOUBLE SEMS SCREW M4X14 + BLK FPH34140
L7 SCREW S-TIGHT 3X8 WASHER HEAD+BLAC GCHS3080
LCD-1 LCD 42W TFT V420H1-L13 UDULCDCME001
SP801 SPEAKER MAGNETIC YDP613-1FN DSD0811EFU01
SP802 SPEAKER MAGNETIC YDP613-1FN DSD0811EFU01
PACKING
S2 STYROFOAM TOP A91H2UH 1EM023725
S3 STYROFOAM BOTTOM A91H2UH 1EM023726
S4 SET BAG A91H2UH 1EM325897
S5 SERIAL NO. LABEL TD812HC ----------
S6 STAND BAG A91H2UH 1EM428517
S12 CARTON(U) A91H2UH 1EM325781
C751 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332 CN802 CONNECTOR BASE 2P(EH) B 2B-EH- J3EHC02JG010
A(LF)(SN)
C752 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
CN901 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007
C801 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
DIODES
C802 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
D201 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C803 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D501 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26
C804 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D502 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26
C805 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D503 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26
C806 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D504 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C807 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D505 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C808 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D506 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C809 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D507 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C810 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D508 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C811 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D509 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C812 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
D511 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C813 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
D512 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C816 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
D601 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2
C817 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
D602 DIODE ZENER 20BSB-T26 NDTB020BST26
C818 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D603 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C819 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D604 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C820 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
D606 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
C821 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D607 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C822 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D608 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2
C823 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D609# DIODE ZENER 39BSB-T26 NDTB039BST26
C824 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
D610# DIODE ZENER 27BSB-T26 NDTB027BST26
C825 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D611 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C826 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D612 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C827 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D613 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C828 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D615 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C829 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D616 DIODE ZENER 1ZB22BB NDWZ0001ZB22
C830 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D617 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C832 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
D618 DIODE FR154 NDLZ000FR154
C833 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
D619 DIODE ZENER 1ZB47BB NDWZ0001ZB47
C834 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
D620 DIODE SCHOTTKY SB360BH NDWZ000SB360
C835 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
D621 SCHOTTKY BARRIER DIODE SB190 NDWZ000SB190
C836 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101
D622 SCHOTTKY BARRIER DIODE SB340 NDWZ000SB340
C837 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
D623 DIODE SCHOTTKY SB360BH NDWZ000SB360
C839 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7
D624 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C840 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7
Q201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R621 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001
Q501 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R622 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002
Q601# MOS FET 2SK3798(Q.M) QFQZSK3798QM R624 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
Q602# NPN TRANSISTOR 2SC5344O-AT NQS002SC5344 R625 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q603 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F R626 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001
Q604 NPN TRANSISTOR POWER 2SC4881F HFE QQWZ2SC4881F R627 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
MAX320 R628 METAL OXIDE FILM RES. 2W J 0.27 Ω RN02R27ZU001
Q605 NPN TRANSISTOR POWER 2SC4881F HFE QQWZ2SC4881F R630 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001
MAX320
R631 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001
Q702 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R632 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
Q703 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R633 RES CARBON FILM T 1/4W J 68 Ω RCX4680T1001
Q704 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R634 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
Q801 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R635 CHIP RES. 1/10W F 3.6k Ω RRXAFR5H3601
Q802 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
R636 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001
Q803 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R638 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q804 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R639 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
RESISTORS
R640 RES. CARBON FILM J 1/2W J 820 Ω RCX2821T1003
R101 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R641 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001
R102 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R642 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R103 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R643 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R104 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R644 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002
R105 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R645 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002
Ref. No. Description Part No. C1207 POLYESTER FILM CAP. (PB FREE) 0.047µF/ CA2A473DT018
100V J
FUNCTION CBA ---------- C1208 CERAMIC CAP. 560pF/2KV CA3D561PAN04
Consists of the following:
C1209 POLYESTER FILM CAP. (PB FREE) 0.0018µF/ CA2A182DT018
CAPACITORS 100V J
C351 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1210 CAP POLYESTER FILM 0.0056µF/100V J CA2A562SER02
C352 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 C1211 CAP POLYESTER FILM 0.0068µF/100V J CA2A682SER02
DIODE C1212 CAP POLYESTER FILM 0.0033µF/100V J CA2A332SER02
D351 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 C1213 CAP CERAMIC (AX) 0.1µF/50V/B/K CA1J104TU061
RESISTORS C1401 POLYESTER FILM CAP. (PB FREE) 0.01µF/ CA2A103DT018
100V J
R351 RES CARBON FILM T 1/4W G 18k Ω RCX4183T1002
C1402 METALIZED POLYESTER FILM CAP. 2.2µF/50V CT1J225DT040
R352 RES CARBON FILM T 1/4W G 8.2k Ω RCX4822T1002 J
R353 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 C1403 CAP POLYESTER FILM 0.22µF/100V J CA2A224SER02
R354 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002 C1404 CAP METALIZED FILM 2.7µF 50V J CT1J275DT039
R355 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 C1405 CAP CERAMIC (AX) 1200pF/50V/B/K CA1J122TU061
R356 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 C1406 POLYESTER FILM CAP. (PB FREE) 0.001µF/ CA2A102DT018
R357 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 100V J
SWITCHES C1407 POLYESTER FILM CAP. (PB FREE) 0.0012µF/ CA2A122DT018
100V J
SW351 TACT SWITCH SKQSAB SST0101AL038
C1408 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
SW352 TACT SWITCH SKQSAB SST0101AL038
C1409 CAP CERAMIC (AX) 0.1µF/50V/B/K CA1J104TU061
SW353 TACT SWITCH SKQSAB SST0101AL038
C1410 CAP CERAMIC (AX) 0.022µF/50V/B/K CA1J223TU061
SW354 TACT SWITCH SKQSAB SST0101AL038
C1411 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
SW355 TACT SWITCH SKQSAB SST0101AL038
C1412 CAP CERAMIC (AX) 0.01µF/50V/F/Z CA1J103TU062
SW357 TACT SWITCH SKQSAB SST0101AL038
C1413 POLYESTER FILM CAP. (PB FREE) 0.001µF/ CA2A102DT018
100V J
IR SENSOR CBA C1414 CAP CERAMIC (AX) 1200pF/50V/B/K CA1J122TU061
C1415 CAP CERAMIC (AX) CH 22pF/50V CA1J220TU059
Ref. No. Description Part No. C1416 CAP CERAMIC (AX) CH 22pF/50V CA1J220TU059
IR SENSOR CBA ---------- C1601# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
Consists of the following:
C1602# CAP METALIZED FILM 1.0µF/300V K 3.5MM CT2F105DC004
CAPACITORS
C1603# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C301 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C1604# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C302 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
C1607 CAP METALIZED FILM J1.0µF/630V/J/MPEF CA2K105DT048
C303 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1610# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1611# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C307 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C1612 CAP ELECTROLYTIC 150µF/400V/M/25/30 CA2H151DYG18
DIODE
C1613 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
D302 LED (WHITE) SLR343WBC7T3XM QPWM343WBC7T
C1614 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
RESISTORS C1701 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
R301 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001 C1702 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
R302 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 C1703 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
R304 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 C1704 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
R305 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 C1705 CAP CERAMIC (AX) 4700pF/50V/B/K CA1J472TU061
MISCELLANEOUS C1706 CERAMIC CAP. B K 100pF/1KV CCD3AKD0B101
RS301 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 C1707 POLYESTER FILM CAP. (PB FREE) 0.1µF/100V CA2A104DT018
J
C1708 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
JUNCTION CBA C1709 CAP CERAMIC (AX) 330pF/50V/B/K CA1J331TU061
Ref. No. Description Part No. C1710 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
JUNCTION CBA ---------- C1711 METALIZED POLYESTER FILM CAP. 0.47µF/ CT1J474DT040
Consists of the following: 50V J
CONNECTOR C1712 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
CN302 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 C1713 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
ST
C1812 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 IC1703# PHOTO COUPLER LTV817MCF NPECLTV817MF
IC1704# PHOTO COUPLER LTV817MBF NPEBLTV817MF
CONNECTORS
IC1705# PHOTO COUPLER LTV817MCF NPECLTV817MF
CN1501 CONNECTOR PRINT OSU 3 S B3P4-VH-L J3VH030JG015
CN1601 CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001 COILS
CN1801 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 L1101 CHOKE COIL 22µH-K LLBD00PKV021
CN1803 CONNECTOR PRINT OSU B14B-PH-K- J3PHC14JG029 L1601# FILTER LLBG00ZY2015 LLBG00ZY2015
S(LF)(SN) L1602# FILTER LLBG00ZY2015 LLBG00ZY2015
CN1804 PH CONNECTOR TOP 10P B10B-PH-K- J3PHC10JG029 L1603# COIL EF 9702 LLEE0Z0KT001
S(LF)(SN)
L1604# COIL EF 9702 LLEE0Z0KT001
DIODES
TRANSISTORS
D1101 SCHOTTKY BARRIER DIODE SB160 NDWZ000SB160
Q1101 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1102 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26
Q1201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1103 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Q1202 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1104 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Q1203# FET 2SK3757(Q) QFWZ02SK3757
D1106 DIODE FR104-B NDLZ000FR104
Q1204# TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1107 DIODE ZENER 9V1BSC-T26 NDTC9R1BST26
Q1401 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
D1108 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q1402 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1109 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
Q1403 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1110 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26
Q1404 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1205 DIODE 1N5399BE NDL1001N5399
Q1601# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1206 DIODE 1N5399BE NDL1001N5399
Q1602# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1207 DIODE 1N5399BE NDL1001N5399
Q1701# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1208 DIODE 1N5399BE NDL1001N5399
Q1702# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1209 DIODE ZENER 18BSB-T26 NDTB018BST26
Q1703 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Q1704 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Q1705 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1212 DIODE ZENER 39BSB-T26 NDTB039BST26
Q1706 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
D1213 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
Q1707 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1215 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Q1708 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1216 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
RESISTORS
D1217 DIODE ZENER 16BSB-T26 NDTB016BST26
R1103 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
D1218 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
R1104 CHIP RES. 1/10W J 270 Ω RRXAJR5Z0271
D1219 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
R1105 RES CARBON FILM T 1/4W G 6.8k Ω RCX4682T1002
D1401 DIODE ZENER 18BSB-T26 NDTB018BST26
R1106 RES CARBON FILM T 1/4W G 27k Ω RCX4273T1002
D1402 DIODE ZENER 24BSB-T26 NDTB024BST26
R1107 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
D1601# DIODE BRIDGE D10XB60-7000 QDWZ0D10XB60
R1108 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
D1602 DIODE ZENER 4V7BSB-T26 NDTB4R7BST26
R1109 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001
D1603 DIODE ZENER 27BSB-T26 NDTB027BST26
R1206 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
D1604 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60
R1207 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
D1605 DIODE ZENER 27BSB-T26 NDTB027BST26
R1208 RES CARBON FILM T 1/4W J 560 Ω RCX4561T1001
D1606 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60
R1209 RES CARBON FILM T 1/4W J 33k Ω RCX4333T1001
D1607 DIODE ZENER 4V7BSB-T26 NDTB4R7BST26
R1210 CHIP RES. 1/10W J 220k Ω RRXAJR5Z0224
D1703 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
R1211 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
D1704 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
R1212 CHIP RES. 1/10W F 4.3k Ω RRXAFR5H4301
D1705 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
R1213 CHIP RES. 1/10W F 4.7k Ω RRXAFR5H4701
Ref. No. Description Part No. C612 POLYESTER FILM CAP. (PB FREE) 0.0022µF/ CA2A222DT018
100V J
DIGITAL MAIN CBA UNIT A91H5MMA-001 C614 ELECTROLYTIC CAP 3300µF/25V M CE1EMZNDL332
C615 ELECTROLYTIC CAP 3300µF/25V M CE1EMZNDL332
C751 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332 CN802 CONNECTOR BASE 2P(EH) B 2B-EH- J3EHC02JG010
A(LF)(SN)
C752 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
CN901 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007
C801 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
DIODES
C802 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
D201 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C803 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D501 DIODE ZENER 52 5V1BSB-T52 NDJB5R1BST52
C804 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D502 DIODE ZENER 52 5V1BSB-T52 NDJB5R1BST52
C805 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D503 DIODE ZENER 52 5V1BSB-T52 NDJB5R1BST52
C806 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D504 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C807 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D505 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C808 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D506 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C809 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D507 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C810 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D508 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C811 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D509 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C812 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
D511 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C813 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
D512 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C816 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
D601 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2
C817 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
D602 DIODE ZENER 52 20BSB-T52 NDJB020BST52
C818 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D603 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C819 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D604 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C820 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
D606 DIODE ZENER 52 5V6BSB-T52 NDJB5R6BST52
C821 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D607 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C822 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D608 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2
C823 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D609# DIODE ZENER 52 39BSB-T52 NDJB039BST52
C824 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
D610# DIODE ZENER 52 27BSB-T52 NDJB027BST52
C825 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D611 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C826 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D612 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
C827 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D613 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C828 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D615 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C829 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D616 DIODE ZENER 1ZB22BB NDWZ0001ZB22
C830 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D617 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C832 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
D618 DIODE FR154 NDLZ000FR154
C833 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
D619 DIODE ZENER 1ZB47BB NDWZ0001ZB47
C834 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
D620 DIODE SCHOTTKY SB360BH NDWZ000SB360
C835 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
D621 SCHOTTKY BARRIER DIODE SB190 NDWZ000SB190
C836 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101
D622 SCHOTTKY BARRIER DIODE SB340 NDWZ000SB340
C837 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
D623 DIODE SCHOTTKY SB360BH NDWZ000SB360
C839 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7
Q201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R621 RES CARBON FILM J 52 1/4W J 4.7k Ω RCX4472T1004
Q501 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R622 RES CARBON FILM J 52 1/4W G 2.7k Ω RCX4272T1005
Q601# MOS FET 2SK3798(Q.M) QFQZSK3798QM R624 RES CARBON FILM J 52 1/4W J 220 Ω RCX4221T1004
Q602# NPN TRANSISTOR 2SC5344O-AT NQS002SC5344 R625 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q603 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F R626 RES CARBON FILM J 52 1/4W J 1.2k Ω RCX4122T1004
Q604 NPN TRANSISTOR POWER 2SC4881F HFE QQWZ2SC4881F R627 RES CARBON FILM J 52 1/4W J 220 Ω RCX4221T1004
MAX320 R628 METAL OXIDE FILM RES. 2W J 0.27 Ω RN02R27ZU001
Q605 NPN TRANSISTOR POWER 2SC4881F HFE QQWZ2SC4881F R630 RES CARBON FILM J 52 1/4W J 22 Ω RCX4220T1004
MAX320
R631 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001
Q702 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R632 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
Q703 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R633 RES CARBON FILM J 52 1/4W J 68 Ω RCX4680T1004
Q704 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R634 RES CARBON FILM J 52 1/4W J 10 Ω RCX4100T1004
Q801 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R635 CHIP RES. 1/10W F 3.6k Ω RRXAFR5H3601
Q802 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
R636 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001
Q803 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R638 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q804 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R639 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
RESISTORS
R640 RES. CARBON FILM J 1/2W J 820 Ω RCX2821T1003
R101 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R641 RES CARBON FILM J 52 1/4W J 4.7k Ω RCX4472T1004
R102 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R642 RES CARBON FILM J 52 1/4W J 220 Ω RCX4221T1004
R103 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R643 RES CARBON FILM J 52 1/4W J 220 Ω RCX4221T1004
R104 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R644 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002
Ref. No. Description Part No. C1207 POLYESTER FILM CAP. (PB FREE) 0.047µF/ CA2A473DT018
100V J
FUNCTION CBA ---------- C1208 CERAMIC CAP. 560pF/2KV CA3D561PAN04
Consists of the following:
C1209 POLYESTER FILM CAP. (PB FREE) 0.0018µF/ CA2A182DT018
CAPACITORS 100V J
C351 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1210 CAP POLYESTER FILM 0.0056µF/100V J CA2A562SER02
C352 CAP CERAMIC AXIAL 52 100000pF/50V/F/Z CA1J104TU098 C1211 CAP POLYESTER FILM 0.0068µF/100V J CA2A682SER02
DIODE C1212 CAP POLYESTER FILM 0.0033µF/100V J CA2A332SER02
D351 DIODE ZENER 52 5V6BSB-T52 NDJB5R6BST52 C1213 CAP CERAMIC AXIAL 52 100000pF/50V/B/K CA1J104TU097
RESISTORS C1401 POLYESTER FILM CAP. (PB FREE) 0.01µF/ CA2A103DT018
100V J
R351 RES CARBON FILM J 52 1/4W G 12k Ω RCX4123T1005
C1402 METALIZED POLYESTER FILM CAP. 2.2µF/50V CT1J225DT040
R352 RES CARBON FILM J 52 1/4W G 8.2k Ω RCX4822T1005 J
R353 RES CARBON FILM J 52 1/4W G 4.7k Ω RCX4472T1005 C1403 CAP POLYESTER FILM 0.22µF/100V J CA2A224SER02
R354 RES CARBON FILM J 52 1/4W G 2.7k Ω RCX4272T1005 C1404 CAP METALIZED FILM 2.7µF 50V J CT1J275DT039
R355 RES CARBON FILM J 52 1/4W G 4.7k Ω RCX4472T1005 C1405 CAP CERAMIC AXIAL 52 1200pF/50V/B/K CA1J122TU097
R356 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 C1406 POLYESTER FILM CAP. (PB FREE) 0.001µF/ CA2A102DT018
R357 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 100V J
SWITHCES C1407 POLYESTER FILM CAP. (PB FREE) 0.0012µF/ CA2A122DT018
100V J
SW351 TACT SWITCH SKQSAB SST0101AL038
C1408 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
SW352 TACT SWITCH SKQSAB SST0101AL038
C1409 CAP CERAMIC AXIAL 52 100000pF/50V/B/K CA1J104TU097
SW353 TACT SWITCH SKQSAB SST0101AL038
C1410 CAP CERAMIC AXIAL 52 22000pF/50V/B/K CA1J223TU097
SW354 TACT SWITCH SKQSAB SST0101AL038
C1411 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
SW355 TACT SWITCH SKQSAB SST0101AL038
C1412 CAP CERAMIC AXIAL 52 10000pF/50V/F/Z CA1J103TU098
SW357 TACT SWITCH SKQSAB SST0101AL038
C1413 POLYESTER FILM CAP. (PB FREE) 0.001µF/ CA2A102DT018
100V J
IR SENSOR CBA C1414 CAP CERAMIC AXIAL 52 1200pF/50V/B/K CA1J122TU097
C1415 CAP CERAMIC AXIAL 52 22pF/50VCH/J CA1J220TU095
Ref. No. Description Part No. C1416 CAP CERAMIC AXIAL 52 22pF/50VCH/J CA1J220TU095
IR SENSOR CBA ---------- C1601# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
Consists of the following:
C1602# CAP METALIZED FILM 1.0µF/300V K 3.5MM CT2F105DC004
CAPACITORS
C1603# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C301 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C1604# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C302 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
C1607 CAP METALIZED FILM J1.0µF/630V/J/MPEF CA2K105DT048
C303 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1610# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1611# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C307 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C1612 CAP ELECTROLYTIC 150µF/400V/M/25/30 CA2H151DYG18
DIODE
C1613 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
D302 LED (WHITE) SLR343WBC7T3XM QPWM343WBC7T
C1614 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
RESISTORS C1701 CAP CERAMIC AXIAL 52 100000pF/50V/F/Z CA1J104TU098
R301 RES CARBON FILM J 52 1/4W J 100 Ω RCX4101T1004 C1702 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
R302 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 C1703 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
R304 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 C1704 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
R305 RES CARBON FILM J 52 1/4W J 1k Ω RCX4102T1004 C1705 CAP CERAMIC AXIAL 52 4700pF/50V/B/K CA1J472TU097
MISCELLANEOUS C1706 CERAMIC CAP. B K 100pF/1KV CCD3AKD0B101
RS301 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 C1707 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C1708 CAP CERAMIC AXIAL 52 100000pF/50V/F/Z CA1J104TU098
JUNCTION CBA C1709 CAP CERAMIC AXIAL 52 330pF/50V/B/K CA1J331TU097
C1710 CAP CERAMIC AXIAL 52 100000pF/50V/F/Z CA1J104TU098
Ref. No. Description Part No.
C1711 METALIZED POLYESTER FILM CAP. 0.47µF/ CT1J474DT040
JUNCTION CBA ---------- 50V J
Consists of the following: C1712 CAP CERAMIC AXIAL 52 100000pF/50V/F/Z CA1J104TU098
CONNECTOR C1713 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
CN302 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 C1714 CAP METALIZED FILM J0.039µF/630V/J/MPEF CA2K393DT045
ST
C1807 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 IC1703# PHOTO COUPLER LTV817MCF NPECLTV817MF
C1811 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 IC1704# PHOTO COUPLER LTV817MBF NPEBLTV817MF
C1812 CAP CERAMIC AXIAL 52 1000pF/50V/B/K CA1J102TU097 IC1705# PHOTO COUPLER LTV817MCF NPECLTV817MF
CONNECTORS COILS
CN1501 CONNECTOR PRINT OSU 3 S B3P4-VH-L J3VH030JG015 L1101 CHOKE COIL 22µH-K LLBD00PKV021
CN1803 CONNECTOR PRINT OSU B14B-PH-K- J3PHC14JG029 When you replace one of the below Coils on this CBA, please replace
S(LF)(SN) with the one that has same parts number.
Do not mix different parts number’s Coil.
DIODES L1603# COIL EF 9702 LLEE0Z0KT001
D1101 SCHOTTKY BARRIER DIODE SB160 NDWZ000SB160 L1604# COIL EF 9702 LLEE0Z0KT001
D1102 DIODE ZENER 52 8V2BSB-T52 NDJB8R2BST52 or
D1103 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148 L1603# COIL EF JLC2518 LLEE0Z0XB007
D1104 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148 L1604# COIL EF JLC2518 LLEE0Z0XB007
D1106 DIODE FR104-B NDLZ000FR104
TRANSISTORS
D1107 DIODE ZENER 52 9V1BSC-T52 NDJC9R1BST52
Q1101 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1108 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q1201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1109 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
Q1202 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1110 DIODE ZENER 52 3V9BSB-T52 NDJB3R9BST52
Q1203# FET 2SK3757(Q) QFWZ02SK3757
D1205 DIODE 1N5399BE NDL1001N5399
Q1204# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
D1206 DIODE 1N5399BE NDL1001N5399
Q1401 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
D1207 DIODE 1N5399BE NDL1001N5399
Q1402 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1208 DIODE 1N5399BE NDL1001N5399
Q1403 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1209 DIODE ZENER 52 18BSB-T52 NDJB018BST52
Q1404 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1210 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
Q1601# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1211 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
Q1602# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1212 DIODE ZENER 52 39BSB-T52 NDJB039BST52
Q1701# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1213 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
Q1702# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1215 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
Q1703 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1216 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
Q1704 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1217 DIODE ZENER 52 16BSB-T52 NDJB016BST52
Q1705 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1218 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
Q1706 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
D1219 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
Q1707 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1401 DIODE ZENER 52 18BSB-T52 NDJB018BST52
Q1708 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1402 DIODE ZENER 52 24BSB-T52 NDJB024BST52
RESISTORS
D1601# DIODE BRIDGE D10XB60-7000 QDWZ0D10XB60
R1103 RES CARBON FILM J 52 1/4W J 10 Ω RCX4100T1004
D1602 DIODE ZENER 52 4V7BSB-T52 NDJB4R7BST52
R1104 CHIP RES. 1/10W J 270 Ω RRXAJR5Z0271
D1603 DIODE ZENER 52 27BSB-T52 NDJB027BST52
R1105 RES CARBON FILM J 52 1/4W G 6.8k Ω RCX4682T1005
D1604 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60
R1106 RES CARBON FILM J 52 1/4W G 27k Ω RCX4273T1005
D1605 DIODE ZENER 52 27BSB-T52 NDJB027BST52
R1107 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
D1606 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60
R1108 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
D1607 DIODE ZENER 52 4V7BSB-T52 NDJB4R7BST52
R1109 RES CARBON FILM J 52 1/4W J 22 Ω RCX4220T1004
D1703 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
R1206 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
D1704 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
R1207 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
D1705 DIO DE SWITCHING 52 HSS4148TA-E QDJZ0HSS4148
R1208 RES CARBON FILM J 52 1/4W J 560 Ω RCX4561T1004
D1706 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140
R1209 RES CARBON FILM J 52 1/4W J 33k Ω RCX4333T1004
D1707 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140
R1210 CHIP RES. 1/10W J 220k Ω RRXAJR5Z0224
D1708 DIODE ZENER 52 4V7BSB-T52 NDJB4R7BST52
R1211 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
Ref. No. Description Part No. C612 POLYESTER FILM CAP. (PB FREE) 0.0022µF/ CA2A222DT018
100V J
DIGITAL MAIN CBA UNIT A91H9MMA-005 C614 ELECTROLYTIC CAP 3300µF/25V M CE1EMZNDL332
C615 ELECTROLYTIC CAP 3300µF/25V M CE1EMZNDL332
C751 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332 CN802 CONNECTOR BASE 2P(EH) B 2B-EH- J3EHC02JG010
A(LF)(SN)
C752 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
CN901 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007
C801 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
DIODES
C802 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
D201 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C803 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D501 DIODE ZENER HZS5.1NB2TA-EQ QDJB0HZS5R1N
C804 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D502 DIODE ZENER HZS5.1NB2TA-EQ QDJB0HZS5R1N
C805 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D503 DIODE ZENER HZS5.1NB2TA-EQ QDJB0HZS5R1N
C806 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D504 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C807 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D505 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C808 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D506 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C809 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D507 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C810 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D508 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C811 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D509 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C812 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
D511 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C813 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
D512 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C816 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
D601 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2
C817 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
D602 DIODE ZENER HZS20NB2TA-EQ QDJBHZS20NB2
C818 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D603 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C819 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D604 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C820 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
D606 DIODE ZENER HZS5.6NB2TA-EQ QDJB0HZS5R6N
C821 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D607 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C822 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D608 DIODE SCHOTTKY BARRIER 1H8-A2 NDTZ0001H8A2
C823 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D609# DIODE ZENER HZS39NB2TA-EQ QDJBHZS39NB2
C824 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
D610# DIODE ZENER HZS27NB2TA-EQ QDJBHZS27NB2
C825 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
D611 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C826 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
D612 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
C827 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D613 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C828 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D615 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C829 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D616 DIODE ZENER 1ZB22BB NDWZ0001ZB22
C830 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
D617 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
C832 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
D618 DIODE FR154 NDLZ000FR154
C833 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
D619 DIODE ZENER 1ZB47BB NDWZ0001ZB47
C834 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
D620 DIODE SCHOTTKY SB360BH NDWZ000SB360
C835 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
D621 SCHOTTKY BARRIER DIODE SB190 NDWZ000SB190
C836 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101
D622 SCHOTTKY BARRIER DIODE SB340 NDWZ000SB340
C837 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
D623 DIODE SCHOTTKY SB360BH NDWZ000SB360
C839 ELECTROLYTIC CAP. 4.7µF/50V M H7 CE1JMAVSL4R7
Q201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R621 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001
Q501 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R622 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002
Q601# MOS FET 2SK3798(Q.M) QFQZSK3798QM R624 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
Q602# NPN TRANSISTOR 2SC5344O-AT NQS002SC5344 R625 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q603 TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F R626 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001
Q604 NPN TRANSISTOR POWER 2SC4881F HFE QQWZ2SC4881F R627 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
MAX320 R628 METAL OXIDE FILM RES. 2W J 0.27 Ω RN02R27ZU001
Q605 NPN TRANSISTOR POWER 2SC4881F HFE QQWZ2SC4881F R630 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001
MAX320
R631 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001
Q702 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R632 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
Q703 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R633 RES CARBON FILM T 1/4W J 68 Ω RCX4680T1001
Q704 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R634 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
Q801 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R635 CHIP RES. 1/10W F 3.6k Ω RRXAFR5H3601
Q802 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
R636 METAL RESISTER. 2W J 0.56 Ω RN02R56ZU001
Q803 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R638 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Q804 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
R639 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
RESISTORS
R640 RES. CARBON FILM J 1/2W J 820 Ω RCX2821T1003
R101 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R641 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001
R102 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R642 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R103 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R643 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R104 CHIP RES. 1/10W J 47 Ω RRXAJR5Z0470
R644 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002
Ref. No. Description Part No. C1207 POLYESTER FILM CAP. (PB FREE) 0.047µF/ CA2A473DT018
100V J
FUNCTION CBA ---------- C1208 CERAMIC CAP. 560pF/2KV CA3D561PAN04
Consists of the following:
C1209 POLYESTER FILM CAP. (PB FREE) 0.0018µF/ CA2A182DT018
CAPACITORS 100V J
C351 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1210 CAP POLYESTER FILM 0.0056µF/100V J CA2A562SER02
C352 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 C1211 CAP POLYESTER FILM 0.0068µF/100V J CA2A682SER02
DIODE C1212 CAP POLYESTER FILM 0.0033µF/100V J CA2A332SER02
D351 DIODE ZENER HZS5.6NB2TA-EQ QDJB0HZS5R6N C1213 CAP CERAMIC (AX) 0.1µF/50V/B/K CA1J104TU061
RESISTORS C1401 POLYESTER FILM CAP. (PB FREE) 0.01µF/ CA2A103DT018
100V J
R351 RES CARBON FILM T 1/4W G 12k Ω RCX4123T1002
C1402 METALIZED POLYESTER FILM CAP. 2.2µF/50V CT1J225DT040
R352 RES CARBON FILM T 1/4W G 8.2k Ω RCX4822T1002 J
R353 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 C1403 CAP POLYESTER FILM 0.22µF/100V J CA2A224SER02
R354 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002 C1404 CAP METALIZED FILM 2.7µF 50V J CT1J275DT039
R355 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 C1405 CAP CERAMIC (AX) 1200pF/50V/B/K CA1J122TU061
R356 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 C1406 POLYESTER FILM CAP. (PB FREE) 0.001µF/ CA2A102DT018
R357 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 100V J
SWITCHES C1407 POLYESTER FILM CAP. (PB FREE) 0.0012µF/ CA2A122DT018
100V J
SW351 TACT SWITCH SKQSAB SST0101AL038
C1408 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
SW352 TACT SWITCH SKQSAB SST0101AL038
C1409 CAP CERAMIC (AX) 0.1µF/50V/B/K CA1J104TU061
SW353 TACT SWITCH SKQSAB SST0101AL038
C1410 CAP CERAMIC (AX) 0.022µF/50V/B/K CA1J223TU061
SW354 TACT SWITCH SKQSAB SST0101AL038
C1411 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
SW355 TACT SWITCH SKQSAB SST0101AL038
C1412 CAP CERAMIC (AX) 0.01µF/50V/F/Z CA1J103TU062
SW357 TACT SWITCH SKQSAB SST0101AL038
C1413 POLYESTER FILM CAP. (PB FREE) 0.001µF/ CA2A102DT018
100V J
IR SENSOR CBA C1414 CAP CERAMIC (AX) 1200pF/50V/B/K CA1J122TU061
C1415 CAP CERAMIC (AX) CH 22pF/50V CA1J220TU059
Ref. No. Description Part No. C1416 CAP CERAMIC (AX) CH 22pF/50V CA1J220TU059
IR SENSOR CBA ---------- C1601# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
Consists of the following:
C1602# CAP METALIZED FILM 1.0µF/300V K 3.5MM CT2F105DC004
CAPACITORS
C1603# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C301 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C1604# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C302 CHIP CERAMIC CAP.(1608) CH J 270pF/50V CHD1JJ3CH271
C1607 CAP METALIZED FILM J1.0µF/630V/J/MPEF CA2K105DT048
C303 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1610# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C1611# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C307 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C1612 CAP ELECTROLYTIC 150µF/400V/M/25/30 CA2H151DYG18
DIODE
C1613 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
D302 LED (WHITE) SLR343WBC7T3XM QPWM343WBC7T
C1614 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
RESISTORS C1701 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
R301 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001 C1702 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
R302 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 C1703 CERAMIC CAP. RB 330pF/2KV CA3D331TE006
R304 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 C1704 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
R305 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 C1705 CAP CERAMIC (AX) 4700pF/50V/B/K CA1J472TU061
RS301 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 C1706 CERAMIC CAP. B K 100pF/1KV CCD3AKD0B101
C1707 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
JUNCTION CBA C1708 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
C1709 CAP CERAMIC (AX) 330pF/50V/B/K CA1J331TU061
Ref. No. Description Part No.
C1710 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
JUNCTION CBA ----------
Consists of the following: C1711 METALIZED POLYESTER FILM CAP. 0.47µF/ CT1J474DT040
50V J
CONNECTOR C1712 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
CN302 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 C1713 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
ST
C1714 CAP METALIZED FILM J0.039µF/630V/J/MPEF CA2K393DT045
C1812 CAP CERAMIC (AX) 1000pF/50V/B/K CA1J102TU061 IC1703# PHOTO COUPLER LTV817MCF NPECLTV817MF
IC1704# PHOTO COUPLER LTV817MBF NPEBLTV817MF
CONNECTORS
IC1705# PHOTO COUPLER LTV817MCF NPECLTV817MF
CN1501 CONNECTOR PRINT OSU 3 S B3P4-VH-L J3VH030JG015
CN1601 CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001 COILS
CN1801 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 L1101 CHOKE COIL 22µH-K LLBD00PKV021
CN1803 CONNECTOR PRINT OSU B14B-PH-K- J3PHC14JG029 L1601# FILTER LLBG00ZY2015 LLBG00ZY2015
S(LF)(SN) L1602# FILTER LLBG00ZY2015 LLBG00ZY2015
CN1804 PH CONNECTOR TOP 10P B10B-PH-K- J3PHC10JG029 When you repair any of the below Coils that are being used for this
S(LF)(SN) CBA, please replace every Coils with same parts number.
Do not intermingle Coils with different parts numbers.
DIODES
L1603# COIL EF 9702 LLEE0Z0KT001
D1101 SCHOTTKY BARRIER DIODE SB160 NDWZ000SB160
L1604# COIL EF 9702 LLEE0Z0KT001
D1102 DIODE ZENER HZS8.2NB2TA-EQ QDJB0HZS8R2N
or
D1103 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
L1603# COIL EF JLC2518 LLEE0Z0XB007
D1104 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148
L1604# COIL EF JLC2518 LLEE0Z0XB007
D1106 DIODE FR104-B NDLZ000FR104
D1107 DIODE ZENER HZS9.1NB3TA-EQ QDJC0HZS9R1N TRANSISTORS
D1108 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 Q1101 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
D1110 DIODE ZENER HZS3.9NB2TA-EQ QDJB0HZS3R9N Q1202 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
D1211 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148 Q1601# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1212 DIODE ZENER HZS39NB2TA-EQ QDJBHZS39NB2 Q1602# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1213 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 Q1701# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1215 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148 Q1702# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
D1216 DIODE SWITCHING HSS4148TE-E QDTZ0HSS4148 Q1703 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Chassis FL9.2
16-1 FL9.2REV