Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Submitted by
Fosroc Chemicals
(India) Pvt Limited telephone: fax: email:
“Sapthagiri Palace”, No.38, III Floor ++ 91 80 2355 1500 + 91 80 2355 1510 india@fosroc.com
,12th Cross, CBI Road, Ganganagar
North BANGALORE – 560 024
www.fosroc.com Registered Office: 41st KM, NH4, Nelamangala Taluk, Bangalore Rural Dist. 562111
Constructive solutions
CONTENTS
RECOMMENDED SYSTEM :
PRODUCT DESCRIPTION
ADVANTAGES
PROPERTIES
APPLICATION METHODOLOGY
Page 2 of 11
Constructive solutions
RECOMMENDED SYSTEM:
PRODUCT DESCRIPTION:
Fosroc Membrane HDPE -P is a unique membrane HDPE film pressure sensitive adhesive
which allows poured concrete to bond fully with the membrane.
Fosroc Membrane HDPE-P provides water, water vapour and gas protection to water
excluding structures and protects concrete from aggressive ground salts, chemicals and
hydrocarbons.
Fosroc Membrane HDPE-P is supplied with a self-adhesive selvedge along one side of the
roll to provide sealed laps and a comprehensive range of auxiliary products to simplify the
application process.
ADVANTAGES
Page 3 of 11
Constructive solutions
RECOMMENDED SYSTEM
PRODUCT DESCRIPTION
ADVANTAGES:
Good bonding with concrete applied to membrane, to block water migration between
membrane and the concrete.
Sound anti-puncture performance.
Excellent VOC gas barrier
Excellent chemical resistance -resist to acid, alkali, mold.
Eco-friendly material.
Basement waterproofing protection to grades 1,2 and 3 as defined in BS8102:2009
Inert product - no risk of a reaction with ponded waste prior to concrete being poured
Full range of Fosroc hydrophilic and PVC waterstops
Available to provide complete solution to waterproofing of the structure
Page 4 of 11
Constructive solutions
PROPERTIES
S.
Parameter Fosroc Membrane HDPE-P
No.
MECHANICAL PROPERTIES
27 Mpa
3 Tensile Strength, film (ASTM D412)
Page 5 of 11
Constructive solutions
APPLICATION METHODOLOGY:
Application – Horizontal
The Fosroc Membrane HDPE-P shall be applied with sanded face uppermost to receive
fresh concrete to which it will chemically adhere.
Laps between sheets shall be rolled to ensure good adhesion of the selvedge.
Roll ends or cut edges shall be sealed on the underside with Fosroc Membrane HDPE-P
sealed tape/ HDPE tape sealed on the top side with a seam of Fosroc membrane HDPE-P
sanded tape.
Alternatively heat sealing shall be used to seal roll ends or cut edges and followed by
seamed sanded tape.
Penetrations through the membrane i.e. pipe entries, shall be made watertight using Fosroc
Membrane HDPE-P with the accessories.
Only ancillary products of Fosroc membranes may be used in conjunction with the Fosroc
membrane HDPE-P
Water proof joints at concave and convex corner details, cut the gusset with appropriate
size and eliminate the needle holes at corners. Stick with double-face adhesive tape for
self-adhesive overlapping.
Application - Vertical
Where Fosroc Membrane HDPE-P is applied to removable formwork; it is recommended
that a minimum concrete compressive strength of 10N/mm² is reached before the formwork
is stripped.
Mechanically fasten the membrane vertically using fasteners appropriate to the substrate
with sanded face uppermost to receive fresh concrete to which it will chemically adhere.
The membrane may be installed in any convenient length. Fastening can be made through
the selvedge using a small and low profile head fastener so that the membrane lays flat and
allows firmly rolled overlaps.
Ensure the underside of the succeeding sheet is clean, dry and free from contamination
before attempting to overlap. Roll firmly to ensure a watertight seal.
Page 6 of 11
Constructive solutions
Overlap all roll ends and cut edges and ensure the area is clean and free from
contamination and apply Fosroc membrane HDPE-P sealed tape and roll.
Pile tops
Cut the Fosroc membrane HDPE-H tight around the pile top
Create formwork as necessary and mix and pour Supercast EPT to fully encapsulate the
pile top and edges and seamlessly join to the Fosroc Membrane HDPE-P
Adhere a strip of Fosroc Membrane HDPE-P to the Supercast EPT sides all around the pile
top and apply seam of Fosroc polyurea WCS/sanded tape/Nitoproof 600 all around the pile
top.
Page 7 of 11
Constructive solutions
(As an Optional ) Care shall be taken during soil compaction. Any chances of damaging the
membrane, a 350 gsm Geotextile layer shall be provided as protective layer on membrane
prior back filling.
Concreting (RCC)
After Membrane is placed,.
Concrete shall be admixed with Auramix 300/400 during batch mixing at batching plant.
Fosroc Concrete Technologist shall be contacted.
Page 8 of 11
Constructive solutions
After filling the Footing area, providing Swellable bar Supercast SW20 with Supercast SWX
adhesive onto the periphery of Footing connected to Grade slab. Placed towards the
positive side of the joint by leaving the 70mm concrete cover. Reference – Above system
drawing.
Page 9 of 11
Constructive solutions
Page 10 of 11
Constructive solutions
Page 11 of 11