Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
2. Applications
3. 3D Metrology
3.1 Photogrammetry
3.3 Surface Defect Detection with Estimated Reference without Nominal Data
4. 3D Testing
4.2 Enhancements for the ARAMIS Kiosk Interface for Material Tests
5.3 Construction
5.3.1 Construct Curve from 2D Geometrical Element
5.3.2 Construct Projected Point Distance/Point-Direction Distance
5.3.3 Deviation Labels on Point Clouds and Vector Fields
5.4 Selection in 3D
To watch the embedded videos in high image resolution, play them on full
screen.
Just click the video with the right mouse button and then select “Full
Screen Multimedia”.
System Requirements
GOM Software 2018 for Windows
Recommended:
Intel Core i7 (QuadCore),
16 GB RAM or more
(depending on mesh/project size),
Certified graphics board,
Windows 7 SP1 64 Bit with current
security updates
Certified & Compatible Graphics Boards and Drivers for Microsoft Windows 7 and Windows 10
Notebooks: Workstations:
Windows Windows Windows Windows 10
Graphics Board Model Graphics Board
7 64Bit 10 64Bit 7 64Bit 64Bit
Quadro FX 360M (256 MB) Dell M4300 186.81 Quadro FX 1500 (256 MB) 190.38
Quadro FX 770M (512 MB) Dell M4400 188.40 Quadro FX 1700 (512 MB) 190.38
189.74 /
Quadro FX 880M (1024 MB) Dell M4500 Quadro FX 1800 (768 MB) 266.45
275.33
Quadro 2000M (2048 MB) Dell M4600 275.33 Quadro FX 570 (256 MB) 190.38
Quadro K2000M (2048 MB) Dell M4700 341.05 Quadro 600 (1 GB) 266.45
Quadro K2100M (2048 MB) Dell M4800 341.05 Quadro 2000 (1 GB) 341.05
Quadro FX 3700M (1024 MB) Dell M6400 188.40
Quadro 4000 (2 GB) 341.05
Quadro FX 2800M (1024 MB) Dell M6500 188.43
Quadro K2000 (2 GB) 341.05
Quadro 4000M (2048 MB) Dell M6600 275.33
Quadro K4000 (3 GB) 341.05
Quadro K4000M (4096 MB) Dell M6700 341.05
Quadro K4100M (4096 MB) Dell M6800 341.05 Quadro K2200 (4 GB) 341.05
Quadro M1000M (2 GB) Dell M7510 354.56 Quadro K4200 (4 GB) 341.05
Quadro M4000M (4 GB) Dell M7710 354.56 Quadro M2000 (4 GB) 369.26 369.26
Dell Prec. 369.81
Quadro P3000 (6 GB) Quadro M4000 (8 GB) 354.56 354.56
7720
Direct Help
The direct help describes the single elements of the dialogs and their
functions.
More explanations about new features will be added shortly.
GOM Training
Basic Level: Participants get to know their GOM system, learn how to
operate the hardware and create their first software projects.
eLearning
English Spanish
German Portuguese
Chinese Italian
Japanese Polish
ATOS ARAMIS
GOM Scan GOM Snap
ATOS Professional ARAMIS Professional
ATOS XL Professional ARAMIS XL Professional
ATOS Professional VMR
ATOS XL Professional VMR
PONTOS Live
PONTOS Live
GOM Scan
Basic scanning
Mesh export
∙ Touch probe
∙ Adapters
∙ Tracking
∙ Professional inspection
Image processing
Bundle adjustment
Challenge
Inspection of flat specimens
Enhancement
You can now use all ARAMIS 3D Cameras and ARAMIS Adjustable Base as
2D sensors. Remove one camera if you want to use it as 2D sensor.
The option “Use left camera”/ “Use right camera” is not available
anymore.
Sensor setup is adapted for the case of a 2D sensor, so that some widgets
and hints are hidden (e.g. camera distance).
You can still use all relevant functions, such as live measuring, tracking,
create measuring sequences.
Advantages
Parts can be measured at different locations.
Only digital data has to be transferred.
Target
Investigation of particular parts to nominal data but also
in the context of assembly situations with other parts is
needed.
Applications:
∙ Cars with mounting parts (body in white, doors, …)
∙ Casting application (especially sand casting)
∙…
“New Project”
Standard workflow
Scanning and inspection as usual
Simulate and evaluate the digital assembly of multiple parts, for example,
casting applications, sheet metal inspections.
Create several parts of which each can be assigned to nominal and actual
data.
Note for users of the free GOM Inspect software: You can open a project
(parts) in GOM Inspect, but you cannot create a project with multiple
parts from scratch.
Display of the complete CAD assembly tree in the similar layout as in the
original CAD application
Elements are not yet usable for inspection - they need to be moved to a
part.
PMI elements show up in a special “PMI” section. In the 3D view, they are
displayed as annotations.
Move imported CAD assembly tree elements to a part per drag & drop
Challenge
New features
You can not only align the actual data of a measuring object with the nominal
data, but also create alignments between the actual data of multiple parts.
This type of alignment supports digital assembly and is used, for example, in
the casting and sheet metal industry.
To align the actual data of a part with the actual data of other parts, your
project must fulfill the following prerequisites:
To align actual parts with each other, you can use the following alignments:
∙ Prealignment
∙ RPS alignment
∙ Local best-fit
∙ By geometrical elements
∙ By coordinate systems
Mind the Alignment hierarchy and the active alignment in your project.
Alignments between actual parts are based on the spatial position of the
target part.
If you created alignments for the target part, the alignment between actual
parts is based on one of these alignments. With the alignment hierarchy, you
define on which alignment of the target part the new alignment is based.
If you change the alignment of the target part or switch the active alignment
in the project, the alignment between actual parts as well as the elements
depending on the alignment are not computed.
Recompute the alignment between the actual parts. Use button .
Challenge
Move actual data of one part to achieve the nominal distance value between
the actual datasets.
Enhancement
RPS allows now also nominal distance elements which are linked
to actual distance.
Construction of distances:
Challenge
You measured parts in their physically assembled state and want to keep
the measured coordinate system.
Enhancement
You can use constraints for different alignment functions, for example, a
local best-fit or RPS alignment.
Challenge
Translation along line without rotation around line
Enhancement
∙ Constraint: Line
New option: Allow rotation around line.
This option is enabled by default. If you disable this option,
only a translation along the line is allowed.
∙ Constraint: General
New option: Actual coordinate systems can be selected.
Enhancements
Digital Assembly – Part-Based Evaluation
CAD Assembly Tree in New Projects
(Parts)
Inter-Part Alignment
Challenge
∙ Independent of ambient
temperature and robot stability
Improvements
Results
Challenge
Enhancement
Challenge
Reference cubes should not be placed too near to
measuring positions of the measurement plan.
The reference cubes should not interfere with the
measurement positions.
Enhancement
The enhanced function is available under Scripting
Script Choice Measurement Strategy
Robogrammetry Show Missing Reference Cubes
(script).
Challenge
User interaction in between
teaching steps
Enhancement
Simplification of needed teaching
steps:
∙ Combined in a system script
∙ No user interaction necessary
anymore in between the single
workflow steps
Challenge
New feature
Inspection
Measuring Principle: Intersection Point Cylinder/Plane
After you used the measuring principle, you can check the
nominal circle. Suitable checks are, for example, the total
deviation in space (dXYZ), the deviation in normal direction (dN)
or the deviation in the plane (dIP). The software shows the label
with the deviations to the created actual point.
Advantages
Challenge
Enhancement
You can now measure a scan area and its inverse at the same time.
A manual scan area avoids reflections, but deletes data.
The mode Manually defined plus inverted avoids reflections while
retaining data.
Still just a single measurement position (“manual reflection detection”)
Challenge
New feature
Advantages
∙ Default tool
∙ Single hole, single sheet
∙ No background
∙ Larger holes
∙ Deeper hole walls
∙ When scan data available
Challenge
Use Case
New Feature
Copied section (Result Actual data
You can now create a complete section even if the edges element of the new function) (Target element)
of the actual part are incomplete.
Challenge
Polygonize different objects separately after scanning them in one
measurement series
New Feature
New options are available in the expert parameters of the function
Polygonize And Recalculate.
If you scan one part per measurement series, choose the option
Measurement series contains one part. This option is set as default.
Challenge
Sharing gray value feature information between departments means sharing the whole project.
Exporting the mesh to be used by other tools does mean that the Gray Value Information can not be transferred
with the mesh.
New feature
Gray value features are incorporated into the polygonization.
If you enable the option Complete mesh up to border lines, the software
completes the mesh up to the border lines of the gray value features during
the polygonization process. Therefore, the information of the gray value
feature computation is transfered to the mesh.
So, you can create and check, for example, a fitting element for hole
geometries using a measuring principle directly on the mesh.
Option enabled
Challenge
CAD is usually modelled with all layers of sheet metals,
but the actual mesh often only represents the outer
shell.
Enhancement
The GOM Software 2018 offers an improved plausibility check for sheet
metal applications.
Select by Curve
Challenge
Inspect multi-part or multilayer measuring objects (e.g. tools,
workpieces, components). Often two actual meshes are analyzed in such
applications.
New feature
Determine whether the contact surfaces are exactly aligned with each
other. For this purpose, you create a surface distance between the actual
meshes of the two parts.
Enhancement
To compute the distance between two surfaces, use
the function Create Surface Distance.
Info
The button Invert surface direction is active only if
option Respect normal vectors is enabled. If the
button is disabled, enable the option.
New Feature
Draft Angle Map
Challenge
If, for example, a tool is removed from its mold
(demolding), parts of the mold can be damaged.
That is why the user has to know on which surfaces
problems can occur.
New feature
Using this function, you can also assign tolerances to Actual draft angle map
draft angles.
Improved Workflow
Improved Workflow for Inspecting Tolerance Regions
Challenge
Create points as limits of tolerance regions on an airfoil profile
(You construct the points by intersecting the airfoil profile with circles.)
New feature
You can find the new function under Construct Point Other
Intersection Point Curve/Circular Element.
Challenge
∙ Determine whether any areas of the airfoil profile lie outside the
tolerance regions especially if non-uniform tolerances are defined.
∙ There might be an area, where deviations are smaller but so is also the
tolerance, so that actually they are out of tolerance.
Enhancement
You can now create a Deviation Label Max. Dev. To Tolerance (Rel.).
Therefore, open I-Inspect Check.
You can view the points out of tolerance in the table, for example.
You create the new deviation label also on curves with tolerances from
CAD, if the CAD has different tolerances among the patches.
Select by Curve
Quality Estimation
Quality Estimation for Photogrammetry
Challenge
Direct quality evaluation for every single 3D point
Result
Precision for every single point is estimated based on
precision of input values and measuring setup
Benefits
Properties tab
Save travel costs and time by doing augmented reality audits with
suppliers in a live stream.
Challenge
Inspect surface defects against a reference can be
needed in order to differentiate real shape and features
from defects.
But:
Enhancement
You can now create a smoothed surface based on the
actual mesh in the GOM Software 2018 and use it as
reference.
Optimized Workflow
Elements
Optimized Workflow
GD&T Quick Creation
Challenge
Enhancement
Challenge
Evenly distributed deviation labels on GD&T elements
Enhancement
You can create equidistant deviation labels on GD&T
elements now.
Challenge
Use cases
∙ No geometry references
∙…
Enhancement
In addition:
Challenge
Repeating tasks which you want to save as a standard
procedure
Use cases
Flush and gap inspection
Airfoil analysis
Enhancements
Downward compatible
Description
If you entered a description when defining the inspection principle, you
can display it with F1 or the question mark as direct help. If no
description is defined, the general direct help on how to apply a user-
defined inspection principle appears.
Enhancements
Enhancements
Replicate tags:
You can create tags on your first section which include the UDIP base element (plane). For example, you may
want to create tags for different groups of airfoil inspection elements:
∙ Thicknesses
∙ Angles
∙ Form and Position
∙ Etc.
These tags are replicated for each new parent plane to which you apply the UDIP.
Challenge
Enhancement
Challenge
New feature:
You can also enable this option, if you are sure that you do not need the
automatic calibration of the measuring setup.
After calibrating your measuring setup, you can set all collision-free paths
automatically as uncritical.
You can save time because you do not need to validate your
measurement series in reality.
To automatically set collision-free paths as uncritical, you can also use the
function under Acquisition Automation Path Status Automatically
Set Collision-Free Paths As Uncritical.
Challenge
Enhancement
Challenge
Performance of the complete scanning process
Enhancement
Reduced computation time for:
∙ Automatic exposure time
∙ Image acquisition
∙ Movement and lighting checks
∙ Reference points
Enhancements
Challenge
Enhancement
∙ Buckles
∙ Dents
How to
Challenge
Enhancement
Challenge
Carry out standardized, repeatable testing procedures
fast and easily
Enhancements
GOM provides several standard tests. Tensile tests
suiting different norms are included as well as FLC test
and bulge test.
Frame Mode
Challenge
Enhancement
How to
Challenge
Define the position of specimen in the camera
image(s) using different frame modes
Enhancement
Challenge
Enhancement
Challenge
Find out which set of parameters from ARAMIS Adjustable Base is suiting
the environmental conditions
Enhancement
Challenge
Quasi-static load tests from several sides (measured with the same measuring
system)
Use points from different point components for rigid body motion compensation
Enhancement
You can now create regions based on facet point components or point
components.
How to
You can use the component region for a rigid body motion compensation,
for example.
Challenge
Add arbitrary data from CSV files not only to surface components but also to
point components and facet point components
Enhancement
You can now also add arbitrary data to point components and facet point
components.
Import a CSV file as ASCII format. You can set the unit and reference source
after the import.
For example, you can import a CSV file containing a column with volume
data for each component point in a specific stage.
Add all Remaining Points to a Point Component
Challenge
Enhancement
You can select now all points which are not used in a
component yet.
Challenge
Challenge
Enhancement
Time stamps for stages are stored in nanosecond resolution. That means
the smallest delta between two stages is one nanosecond.
Challenge
Enhancement
Challenge
Use case
Enhancement
CT Volume Data
Import of CAD Data – Updated File Formats
Enhanced Functionalities for Exporting Mesh Files
Replace an Existing STL File in a Stage Project
Export CSV/XML
Export UFF Data
Mesh Error Correction
CT Volume Data
Challenge
Enhancement
2018
2017 2018
NX 12 prt
You can find more information about available CAD formats in the direct help.
Challenge
New feature
In the GOM Software 2018, the export of files like G3D, STL, POL, PLY
and JT-Open supports the export of multiple stages.
If you would like to export meshes over multiple stages in your trend
analysis, you can also use this functionality.
You can also export nominal and actual patch compounds as G3D, STL,
POL and PLY file now.
Challenge
Enhancement
∙ Exported stages
∙ Value elements
∙ Points
∙ Sections
∙…
Challenge
Enhancement
The export is easier to use because you just need to use one function.
You can now export bigger data and the export is faster.
Besides surface components, you can now export points, sections, curves,
point components, 6DoF, …
The export was tested with the following third-party tools: ME’scope, PAK,
BK Connect.
Challenge
Enhancement
Sewing errors
Inconsistencies
Challenge
Challenge
New Feature
The new function is available under Construct Curve Other Curve From 2D Geometrical Element.
You can construct an edge curve from a 2D geometrical element. The edge curve has the shape of the
geometrical element.
You can apply this function on nominal data as well as on actual data.
Construct Curve from 2D Geometrical Element
Enhancement
Challenge
New feature
You can find the new function
under Inspection → Create
Deviation Labels On Point Cloud.
Challenge
New feature
Challenge
Enhancement
Challenge
Enhancement
Challenge
New feature
Mouse functions during selection
You can find the new function under
Edit → Selection in 3D → Geometry-Based Selections (These specifications refer to a
→ Select Ellipse-Based. standard mouse setup for a right-
handed person.)
Challenge
Enhancement
You can find the improved function under Edit → Selection in 3D
→ Other Selections → Select By Curve.
If you enable the option Limit selection, the software only selects the
mesh area between the two indicated points Point 1 and Point 2 or
between Point 1 via the additional point to Point 2.
Selected mesh area on the closed
curve C1: The software selects the
mesh area between the points P1
and P2. The selection runs via the
additional point P3.
What's New GOM Software 2018 | GOM GmbH
User Interface
Click .
Challenge
“I would like to scan a part […] and have the color plot on the front page of the PDF report. The client or
engineer would then be able to double-click on the pdf to rotate the part.”
“Only upon seeing things clearly (moving in 3D), people can get more passionate about GOM Inspect.”
“My customers are asking for [3D PDF] simply because they don’t want to learn a new software tool,
because even the free version can be intimidating.”
“I find it really frustrating how everyone expects you to read their mind and select the exact perspective they
think is essential.”
“Maybe a much more stripped down version with just some basic functionalities would do the trick. I would prefer
to build in into GOM Inspect the option to […] shows/hides existing functions.”
New feature
The software keeps the simplified user interface and does not allow to
access the complex full interface and functionality without the password.
Challenge
Enhancement
Codemeter
Update to version 6.5c
Evaluation/measurement system
Depending on the installed software and image
acquisition driver, the system is classified as an
evaluated measurement system.
Additional checks are added for measurements.
Model/OS check
Measuring computers will be checked: known PC
hardware, operating system supported
Check System
Option “Screenshot”
To see what the user sees when creating the bug report (GOMSIC), a
screenshot can now be included directly in the creation process.
Option “Comment”
To give the user the opportunity to directly describe messages that are
important for the bug report (GOMSIC), the comment option was
implemented at gomsic creation.
Updates available
GOM Maintenance
Tool is busy