Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Link
Before starting adjustments SERVICE MODE
Adjusting items when replacing main parts and boards ADJUSTING REMOTE COMMANDER
DATA PROCESS
CAMERA SECTION ADJUSTMENTS
SERVICE MODE
PREPARATIONS BEFORE ADJUSTMENTS
2002I0500-1
©2002.9
9-929-994-51 Sony EMCS Co. Published by DI Customer Center
DSC-F717
TABLE OF CONTENTS
Section Title Page Section Title Page
6. ADJUSTMENTS 1-5. LCD System Adjustments ············································· 6-38
Before Starting Adjustment ······················································· 6-1 1. LCD Initial Data Input (1) ············································· 6-39
1-1. Adjusting Items when Replacing 2. LCD Initial Data Input (2) ············································· 6-39
Main Parts and Boards ···················································· 6-2 3. VCO Adjustment (PD-179 Board) ································ 6-40
6-1. Camera Section Adjustments ··········································· 6-3 4. D Range Adjustment (PD-179 Board) ··························· 6-40
1-1. Preparations Before Adjustments ···································· 6-3 5. Contrast Adjustment (PD-179 Board) ··························· 6-41
1-1-1. List of Service Tools ························································ 6-3 6. V-COM Level Adjustment (PD-179 Board) ·················· 6-41
1-1-2. Preparations ····································································· 6-4 7. V-COM Adjustment (PD-179 Board) ···························· 6-42
1-1-3. Discharging of the Flashlight Power Supply ··················· 6-4 8. White Balance Adjustment (PD-179 Board) ················· 6-42
1-1-4. Precautions ······································································ 6-6 1-6. Color Electronic Viewfinder System Adjustments ········ 6-43
1. Setting the Switch ···························································· 6-6 1. EVF Initial Data Input ··················································· 6-44
2. Order of Adjustments ······················································ 6-6 2. VCO Adjustment (PD-179 Board) ································ 6-44
3. Subjects ··········································································· 6-6 3. Bright Adjustment (PD-179 Board) ······························ 6-45
4. Preparing the Flash Adjustment Box ······························· 6-7 4. Contrast Adjustment (PD-179 Board) ··························· 6-45
1-2. Initialization of A, B, D, E, F, 7, 9 Page Data ················· 6-8 5. White Balance Adjustment (PD-179 Board) ················· 6-46
1-2-1. Initialization of A, D Page Data ······································ 6-8 6-2. Service Mode ································································· 6-47
1. Initializing A, D Page Data ·············································· 6-8 2-1. Adjusting Remote Commander ····································· 6-47
2. Modification of A, D Page Data ······································ 6-8 1. Used the Adjusting Remote Commander ······················ 6-47
3. A Page Table ···································································· 6-8 2. Precautions upon Using the Adjusting
4. D Page Table ···································································· 6-8 Remote Commander ······················································ 6-47
1-2-2. Initialization of B, E, F, 7, 9 Page Data ··························· 6-9 2-2. Data Process ·································································· 6-48
1. Initializing B, E, F, 7, 9 Page Data ·································· 6-9 2-3. Service Mode ································································· 6-49
2. Modification of B, E, F, 7, 9 Page Data. ·························· 6-9 1. Setting the Test Mode ···················································· 6-49
3. B Page Table ···································································· 6-9 2. Bit Value Discrimination ··············································· 6-49
4. E Page Table ···································································· 6-9 3. Mode Dial Check (1) ····················································· 6-50
5. F Page Table ·································································· 6-10 4. Mode Dial Check (2) ····················································· 6-50
6. 7 Page Table ··································································· 6-12 5. Jog Dial Check ······························································ 6-50
7. 9 Page Table ··································································· 6-12 6. Switch Check (1) ··························································· 6-50
1-3. Video System Adjustment ············································· 6-13 7. Switch Check (2) ··························································· 6-51
1. Composite Video Level Adjustment ······························ 6-13 8. LED Check ···································································· 6-51
1-4. Camera System Adjustments ········································· 6-14 9. Self Diagnosis Code ······················································ 6-51
Data Setting During Camera System Adjustments ········ 6-14
Picture Frame Setting ···················································· 6-15 * The sheet for auxiliary light is shown on page 6-52.
Check on the Oscilloscope ············································ 6-15 * The color reproduction frame is shown on page 6-53.
1. HALL Adjustment ························································· 6-16
2. Flange Back Adjustment
(Using the minipattern box) ·········································· 6-17
3. Flange Back Adjustment
(Using the flange back adjustment chart and
Subject More than 500 m Away) ··································· 6-18
4. Flange Back Check ························································ 6-19
5. F No. Compensation ······················································ 6-20
6. Mechanical Shutter Adjustment ···································· 6-20
7. Light Value Adjustment ················································· 6-21
8. Mixed Color Cancel Adjustment ··································· 6-21
9. Auto White Balance 3200K Standard Data Input 1 ······ 6-22
10. Auto White Balance 3200K Standard Data Input 2 ······ 6-22
11. Auto White Balance 3200K Standard Data Input 3 ······ 6-23
12. Auto White Balance 5800K Standard Data Input 1 ······ 6-23
13. Auto White Balance 5800K Standard Data Input 2 ······ 6-24
14. Auto White Balance 5800K Standard Data Input 3 ······ 6-24
15. Auto White Balance 5800K Check 1 ···························· 6-25
16. Auto White Balance 5800K Check 2 ···························· 6-26
17. Auto White Balance 5800K Check 3 ···························· 6-26
18. Auto White Balance 3200K Check 1 ···························· 6-27
19. Auto White Balance 3200K Check 2 ···························· 6-28
20. Auto White Balance 3200K Check 3 ···························· 6-28
21. Color Reproduction Adjustment ···································· 6-29
22. CCD White Defect Compensation ································ 6-30
23. CCD Black Defect Compensation ································· 6-31
24. CCD Linearity Check (Monitoring) ······························ 6-32
25. CCD Linearity Check (Caputure) ·································· 6-34
26. Strobe White Balance Adjustment ································· 6-35
27. LED Illumination Check ··············································· 6-36
28. AF Illumination Check ·················································· 6-37
—2—
DSC-F717
SECTION 6
COVER ADJUSTMENTS
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a
board is replaced.
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM
to the replaced board.
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or in-
stalled, save the data from the same model of the same destination, and download it.
(Machine to be repaired) PC (Machine to be repaired)
6-1
DSC-F717
COVER
(VIDEO AMP)
(LCD panel)
(LCD drive)
EEPROM
(EVR)
RadarW
(COMPLETE)
(COMPLETE)
(COMPLETE)
Adjustment section Adjustment
RadarW
LCD901
LCD902
IC102
IC207
IC201
IC801
IC802
IC901
IC902
IC505
D911
D701
Lens block assy
LB-082 board
SY-080 board
SY-080 board
PD-179 board
PD-179 board
PD-179 board
PD-179 board
PD-179 board
SY-080 board
SY-080 board
FR-194 board
FR-194 board
LCD block
LCD block
Supporting
EVF block
Laser unit
Flash unit
Table 6-1-1
6-2
DSC-F717
COVER
J-11
Fig. 6-1-1
6-3
DSC-F717
1-1-2. Preparations
Note 1: For details of how remove the cabinet and boards, refer
to “2. DISASSEMBLY”. Pattern box
Note 2: When performing only the adjustments, the lens block
and boards need not be disassemble.
Discharge procedure
1. Remove the FR-194 board, and disconnect the harness from
CN404 on the BT-015 board.
2. Fabricate the short jig as shown in Fig. 6-1-5 locally by your-
self. Connect the short jig to the pin 1 and pin 2 of CN404
on the BT-015 board. Allow ten seconds to discharge the volt-
age.
22
Harness CPC cover
1 CPC-12 jig
(J-6082-436-A)
FR-194 board
CN305
BT Fig. 6-1-3
-01
5
1 kΩ/1 W
R:1 kΩ/1 W
(Part code:
1-215-869-11)
6-4
DSC-F717
CN704
(MF51050)
CN703
Need not connected
CN203
SY-080
BOARD
Need not
connected CN101
LENS BLOCK CN702
CN701
CN303
CN302
To
CD-408 BOARD MIC/
SPEAKER To
CN301
CN305
Must be connected to Flash unit CN301
when performing the “Strobe White
Balance Adjustment”. CN001
DC IN jack
AC IN
AC power CPC-12 jig
adaptor CN401 (J-6082-436-A)
CN404
CN403
BT-015
Color BOARD
Video monitor Vectorscope Adjusting
(yellow) Terminated remote
75 Ω commander
Audio
(black)
CN705
CN801
AL-013 BOARD
PD-179 BOARD
PANEL UNIT
CN704
CN851
BOARD
LB-082
SW-379 BOARD
Fig. 6-1-6
6-5
DSC-F717
1-1-4. Precautions
1. Setting the Switch
Unless otherwise specified, set the switches as follows and per-
form adjustments.
1. Mode Dial .......................................... CAMERA
2. FOCUS switch
(FZ51050 block S308) ....................... MANUAL
3. EXPOSURE button
(PW51050 block S404) ..................... 0EV
4. DISPLAY button
(SW-379 board S355) ........................ OSD OFF
5. WHT BAL
(FZ51050 block S304) ....................... AUTO
6. P.EFFECT (Menu display) ................ OFF
7. VIDEO OUT (SET UP setting) ......... NTSC
2. Order of Adjustments
Basically carry out adjustments in the order given.
Magenta
White
Cyan
Green
C C=D D
Red
Blue
Magenta
Yellow
Green
White
Cyan
Blue
Red
CRT picture frame
V
A B A=B B A
Fig. b (monitor TV picture)
Enlargement
Difference in level
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig a
and the monitor TV display shown in Fig. b.
B A
Fig. 6-1-7
3. Subjects
1) Color bar chart (Standard picture frame).
When performing adjustments using the color bar chart, ad-
just the picture frame as shown in Fig. 6-1-7. (Standard pic-
ture frame)
2) Clear chart (Standard picture frame)
Remove the color bar chart from the pattern box and insert a
White
clear chart in its place. (Do not perform zoom operations dur-
841 mm
ing this time)
3) Chart for flange back adjustment Black
Join together a piece of white A0 size paper (1189mm × 841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-8.
1189 mm
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white Fig. 6-1-8
and black paper must not have any undulations.
6-6
DSC-F717
1030 mm 1000 mm
(730 mm) (700 mm)
Fig. 6-1-9
woody board A
woody board B
woody board A
woody board B
woody board C
Fig. 6-1-10
6-7
DSC-F717
COVER
6-8
DSC-F717
Initializing Method:
Order Page Address Data Procedure
1 0 01 01
2 6 03 11
3 6 00 2D
4 6 01 2D Press PAUSE button.
5 6 02 Check the data changes to “01”.
Perform “Modification of B,
6
E, F, 7, 9 page Data”.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camera may not operate.
3) When changing the data, press the PAUSE button of the
adjusting remote commander each time when setting new data
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
6-9
DSC-F717
5. F Page Table
Note 1: Fixed data-1: Initialized data.
(Refer to “1. Initializing the B, E, F, 7, 9 Page Data”)
Note 2: Fixed data-2: Modified data.
(Refer to “2. Modification of B, E, F, 7, 9 Page Data”)
Address Initial value Remark Address Initial value Remark
00 to 0F Fixed data-1 (Initialized data) 3D 00
Flange back adj.
10 58 3E FF
11 FF 3F to 57 Fixed data-1 (Initialized data)
12 FF 58 5D
13 FF 59 82
LED Ilumination check.
14 00 5A 15
Hall adj.
15 90 5B 5B
16 FF 5C 75
17 Fixed data-1 (Initialized data) 5D 5D
18 22 5E 00
19 48 5F 00
1A 2D 60 00
1B 3A 61 00 F No. compensation
1C 13 62 00
1D 00 63 00
1E 00 64 00
1F 00 65 30
20 00 66 FE Light value adj.
21 00 67 6D
22 12 68 68 Hall adj.
23 00 69 to 6D Fixed data-1 (Initialized data)
24 20 6E 00
Mixed color cancel adj.
25 20 6F 00
26 23 70 2B
27 44 71 E4
28 0A 72 1F
29 00 73 8D
2A 00 Flange back adj. 74 2A
AWB 3200K standard data input 1
2B 00 75 90
2C 00 76 21
2D 00 77 13
2E 00 78 00
2F 00 79 00
30 00 7A 00
31 00 7B 00
32 00 7C 00
AWB 3200K standard data input 2
33 00 7D 00
34 00 7E 00
35 00 7F 00
36 00 80 00
37 00 81 00
AWB 3200K standard data input 3
38 00 82 00
39 00 83 00
3A 00 84, 85 Fixed data-1 (Initialized data)
3B 00 86 00
AWB 3200K standard data input 3
3C 00 87 00
6-10
DSC-F717
6-11
DSC-F717
6. 7 Page Table
Note 1: Fixed data-1: Initialized data.
(Refer to “1. Initializing B, E, F, 7, 9 Page Data”)
Note 2: Fixed data-2: Modified data.
(Refer to “2. Modification of B, E, F, 7, 9 Page Data”)
Address Initial value Remark
00 to FF Fixed data-1 (Initialized data)
7. 9 Page Table
Note 1: Fixed data-1: Initialized data.
(Refer to “1. Initializing B, E, F, 7, 9 Page Data”)
Note 2: Fixed data-2: Modified data.
(Refer to “2. Modification of B, E, F, 7, 9 Page Data”)
Address Initial value Remark
00 to FF Fixed data-1 (Initialized data)
6-12
DSC-F717
COVER
Mode PLAY
Signal Arbitrary
Measurement Point Video terminal of A/V OUT jack
(75 Ω terminated)
Measuring Instrument Oscilloscope
Adjustment Page A
Adjustment Address A0
Specified Value Sync level:
A = 286 ± 5 mV (NTSC mode)
A = 300 ± 5 mV (PAL mode)
Burst level:
B = 286 ± 5 mV (NTSC mode)
B = 300 ± 5 mV (PAL mode)
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2 A 02 13 Press PAUSE button.
3 4 F1 04
Change the data and set the
4 A A0 sync level (A) to the specified
value.
5 A A0 Press PAUSE button.
Check the burst level (B) to the
6
specified value.
B
A
Fig. 6-1-11
6-13
DSC-F717
COVER
1-4. CAMERA SYSTEM ADJUSTMENTS After completing the camera system adjustments,
Before perform the camera system adjustments, check that the release the data setting:
specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Order Page Address Data Procedure
isfied.
Note: For “CAMERA SYSTEM ADJUSTMENTS”, perform in 1 E 96 40 Press PAUSE button.
order of item numbers. 2 6 6C 00
3 D 21 00 Press PAUSE button.
Data setting during camera system adjustments
Perform the following data setting before the camera system ad- Set the bit value of bit 5 is
justments. 4 A 0D “1”, and press PAUSE
It is not necessary to perform the following data setting everytime button. (Note 1)
when you perform some items of camera system adjustments con- Set the bit value of bit 1 is
tinuously unless the power is turned off. Only when the power is 5 A 02 “0”, and press PAUSE
turned off during this adjustments, perform the data setting again, button. (Note 1)
then continue the adjustments. Set the bit value of bit 1 is
6 A 00 “0”, and press PAUSE
Set up setting: button. (Note 1)
1) VIDEO OUT of SET UP setting............... NTSC (NTSC mode)
(This adjustment must be performed in NTSC mode, so don't Set the bit value of bit 5 is
7 A 01 “0”, and press PAUSE
set the SET UP setting to “PAL”)
button. (Note 1)
Data setting method: 8 0 01 00
Order Page Address Data Procedure
1 0 01 01
Set the bit value of bit 5 is
2 A 01 “1”, and press PAUSE
button. (Note 1)
Check the bit values of bit3,
3 2 10 bit4 and bit5 are “1”.
(Note 1, 2)
Set the bit value of bit 1 is
4 A 00 “1”, and press PAUSE
button. (Note 1)
Set the bit value of bit 1 is
5 A 02 “1”, and press PAUSE
button. (Note 1)
Set the bit value of bit 5 is
6 A 0D “0”, and press PAUSE
button. (Note 1)
7 D 21 07 Press PAUSE button.
Check the data changes to
8 6 C1
“02”.
9 6 6C 01
10 Wait for 1 second.
11 E 96 00 Press PAUSE button.
Note 1: For the bit values, refer to “6-2. SERVICE MODE”,
“2-3. 2. Bit value discrimination”.
Note 2: In case of wrong data.
• Select page: 2, address: 00 and set data: 29.
• Select page: 2, address: 01 and set data: 29.
• Select page: 2, address: 0C, set the bit value of bit 1 is
1.
• Select page: 2, address: 04 and set data: 04.
Set the adjusting remote commander to normal LANC,
and the power will be turned, off and on automatically.
Note 3: Repeat the “Data setting method”, if the power was turned
off and on during the “CAMERA SYSTEM ADJUST-
MENTS”.
6-14
DSC-F717
Picture Frame Setting How to reset the zoom and focus when they deviated:
Mode CAMERA Order Page Address Data Procedure
Subject Color bar chart 1 6 2C 01
(Standard picture frame with the 2 6 90 00
zoom lens at WIDE end)
3 6 91 00
Measurement Point Video terminal of A/V OUT jack
(75 Ω terminated) 4 6 92 YL (Note 2)
Note 1: Displayed data of the page 1 of adjusting remote com- Check the data changes to
7 6 07
mander. “01”.
1:XX:XX 8 6 01 00 Press PAUSE button.
YL data Note 2: The data noted down at step 7 of “Setting method”.
YH data
Check on the oscilloscope
Switch setting
1) FOCUS ....................................................... AUTO 1. Horizontal period
2) MACRO (Control button) .......................... ON
A=B C=D
Setting method:
B C
Order Page Address Data Procedure
A D
Shoot the color bar chart
1
with the zoom WIDE end.
Enter the output of VIDEO
OUT to the monitor TV, and
2
move the position as shown
in Fig. 6-1-14.
Horizontal width of one color
(B, C) and that of black (A,
3 D) on the color bar chart
should be same. (See Fig. 6-
1-12)
With vertical width of black
(E, F) set in same, the color
4 bar chart should come to the
center of monitor TV. (See
Fig. 6-1-12
Fig. 6-1-13)
Check that the color bar on 2. Vertical period
5
the monitor TV is focused.
6 0 03 22 E E=F F
6-15
DSC-F717
1. HALL Adjustment
RadarW
RadarW
Mode CAMERA
Subject Not required
Measuring Instrument Adjusting remote commander
Adjustment Page F
Adjustment Address 58 to 5D, 68
Note 1: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Adjusting method:
Order Page Address Data Procedure
Perform “Data setting during
1 camera system adjustment”.
(Refer to page 6-14)
2 6 94 16
3 6 95 81
Press PAUSE button.
4 6 01 6D
(Note 2)
Check the data changes to
5 6 02
“01”.
6 6 01 00 Press PAUSE button.
Note 2: The adjustment data will be automatically input to page:
F, address: 58 to 5D and 68.
6-16
DSC-F717
Minipattern box
Camera
Camera
table
Red (+)
Black (–)
Yellow (SENS +)
Fig. 6-1-15
6-17
DSC-F717
6-18
DSC-F717
6-19
DSC-F717
6-20
DSC-F717
Press PAUSE button. Note 2: The adjustment data will be automatically input to page:
3 6 01 0D F, address: 6E and 6F.
(Note 3)
Check the data changes to Processing after Completing Adjustment:
4 6 02
“01”.
Order Page Address Data Procedure
5 0 03 06
1 6 01 00 Press PAUSE button.
Check that the displayed data
6 1 (Note 2) satisfies the AE Set the data noted down at
level 1 specified value. 2 7 12 step 3, and press PAUSE
button.
Check that the displayed data
7 F 65 satisfies the AE level 2 Release the data setting
specified value. 3 performed at step 1.
(Refer to page 6-14)
Note 3: The adjustment data will be automatically input to page:
F, address: 65 to 67.
6-21
DSC-F717
9. Auto White Balance 3200K Standard Data Input 1 10. Auto White Balance 3200K Standard Data Input 2
RadarW RadarW
Adjust the white balance standard data at 3200K. Adjust the white balance standard data at 3200K.
Mode CAMERA Mode CAMERA
Subject Clear chart Subject Clear chart
(Standard picture frame with the (Standard picture frame with the
zoom lens at WIDE end) zoom lens at WIDE end)
Adjustment Page F Adjustment Page F
Adjustment Address 70 to 79, B0, B2, B4 Adjustment Address 7A to 7F
Note 1: Check that the data of page: 6, address: 02 is “00”. Note 1: Perform this data input after performing “Auto White
If not, turn the power of unit OFF/ON. Balance 3200K Standard Data Input 1”.
Note 2: “Auto White Balance 3200K Standard Data Input 1” is Note 2: Check that the data of page: 6, address: 02 is “00”.
available only once after the power is turned on. Turn the If not, turn the power of unit OFF/ON.
power off, then on again if the adjustment is retried. Note 3: “Auto White Balance 3200K Standard Data Input 2” is
available only once after the power is turned on. Turn the
Adjusting method: power off, then on again if the adjustment is retried.
Order Page Address Data Procedure
Adjusting method:
Perform “Data setting during
1 camera system adjustment”. Order Page Address Data Procedure
(Refer to page 6-14) “Auto White Balance 3200K
Perform “Picture Frame 1 Standard Data Input 1” is
2 completed.
setting”. (Refer to page 6-15)
3 6 37 01 2 6 37 04
4 6 B6 03 3 6 01 0B Press PAUSE button. (Note 4)
5 6 01 11 Press PAUSE button. Check the data changes to
4 6 02
“01”.
Check the data changes to
6 6 38 Note 4: The adjustment data will be automatically input to page:
“01”.
F, address: 7A to 7F.
7 6 01 C1 Press PAUSE button. (Note 3)
Check the data changes to Processing after Completing Adjustment:
8 6 02
“01”. Order Page Address Data Procedure
9 6 01 00 Press PAUSE button. 1 6 01 00 Press PAUSE button.
10 6 B6 00 Perform “Auto White
11 6 37 02 2 Balance 3200K Standard
12 6 01 0B Press PAUSE button. (Note 3) Data Input 3”.
Check the data changes to
13 6 02
“01”.
Note 3: The adjustment data will be automatically input to page:
F, address: 70 to 79, B0, B2 and B4.
6-22
DSC-F717
11. Auto White Balance 3200K Standard Data Input 3 12. Auto White Balance 5800K Standard Data Input 1
RadarW RadarW
Adjust the white balance standard data at 3200K. Adjust the white balance standard data at 5800K.
Mode CAMERA Mode CAMERA
Subject Clear chart Subject Clear chart
(Standard picture frame with the (Standard picture frame with the
zoom lens at WIDE end) zoom lens at WIDE end)
Adjustment Page F Filter Filter C14 for color temperature
Adjustment Address 80 to 83, 86, 87 correction
Note 1: Perform this data input after performing “Auto White Adjustment Page F
Balance 3200K Standard Data Input 2”. Adjustment Address 88 to 91, A0 to A3, B1, B3
Note 2: Check that the data of page: 6, address: 02 is “00”. Note 1: Perform this data input after performing “Auto White
If not, turn the power of unit OFF/ON. Balance 3200K Standard Data Input 3”.
Note 3: “Auto White Balance 3200K Standard Data Input 3” is Note 2: Check that the data of page: 6, address: 02 is “00”.
available only once after the power is turned on. Turn the If not, turn the power of unit OFF/ON.
power off, then on again if the adjustment is retried. Note 3: “Auto White Balance 5800K Standard Data Input 1” is
available only once after the power is turned on. Turn the
Adjusting method: power off, then on again if the adjustment is retried.
Order Page Address Data Procedure
“Auto White Balance 3200K Adjusting method:
1 Standard Data Input 2” is Order Page Address Data Procedure
completed. “Auto White Balance 3200K
2 6 37 06 1 Standard Data Input 3” is
3 6 01 0B Press PAUSE button. (Note 4) completed.
Check the data changes to Place the C14 filter on the
4 6 02 2
“01”. lens.
Note 4: The adjustment data will be automatically input to page: 3 F A0 2B Press PAUSE button.
F, address: 80 to 83 and 86 to 87. 4 F A1 10 Press PAUSE button.
5 F A2 5D Press PAUSE button.
Processing after Completing Adjustment:
6 F A3 E0 Press PAUSE button.
Order Page Address Data Procedure
7 6 37 07
1 6 01 00 Press PAUSE button.
8 6 B6 03
Perform “Auto White
2 Balance 5800K Standard 9 6 01 11 Press PAUSE button.
Data Input 1”. Check the data changes to
10 6 38
“01”.
11 6 01 C3 Press PAUSE button. (Note 4)
Check the data changes to
12 6 02
“01”.
13 6 01 00 Press PAUSE button.
14 6 B6 00
15 6 37 08
16 6 01 A5 Press PAUSE button. (Note 4)
Check the data changes to
17 6 02
“01”.
Note 4: The adjustment data will be automatically input to page:
F, address: 88 to 91, A0 to A3, B1 and B3.
6-23
DSC-F717
13. Auto White Balance 5800K Standard Data Input 2 14. Auto White Balance 5800K Standard Data Input 3
RadarW RadarW
Adjust the white balance standard data at 5800K. Adjust the white balance standard data at 5800K.
Mode CAMERA Mode CAMERA
Subject Clear chart Subject Clear chart
(Standard picture frame with the (Standard picture frame with the
zoom lens at WIDE end) zoom lens at WIDE end)
Filter Filter C14 for color temperature Filter Filter C14 for color temperature
correction correction
Adjustment Page F Adjustment Page F
Adjustment Address 92 to 97 Adjustment Address 98 to 9B, 9E, 9F
Note 1: Perform this data input after performing “Auto White Note 1: Perform this data input after performing “Auto White
Balance 5800K Standard Data Input 1”. Balance 5800K Standard Data Input 2”.
Note 2: Check that the data of page: 6, address: 02 is “00”. Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON. If not, turn the power of unit OFF/ON.
Note 3: “Auto White Balance 5800K Standard Data Input 2” is Note 3: “Auto White Balance 5800K Standard Data Input 3” is
available only once after the power is turned on. Turn the available only once after the power is turned on. Turn the
power off, then on again if the adjustment is retried. power off, then on again if the adjustment is retried.
6-24
DSC-F717
6-25
DSC-F717
16. Auto White Balance 5800K Check 2 RadarW 17. Auto White Balance 5800K Check 3
RadarW
RadarW
Mode CAMERA Mode CAMERA
Subject Clear chart Subject Clear chart
(Standard picture frame with the (Standard picture frame with the
zoom lens at WIDE end) zoom lens at WIDE end)
Measurement Point Displayed data of page: F, address: Measurement Point Displayed data of page: F, address
94, 95 9A, 9B
Measuring Instrument Adjusting remote commander Measuring Instrument Adjusting remote commander
Specified Value 1 11 to 4D Specified Value 1 23 to 9B
Specified Value 2 00 to 1D, DC to FF Specified Value 2 00 to 30, DA to FF
Note 1: Perform this check after “Auto White Balance 5800K Note 1: Perform this check after “Auto White Balance 5800K
Check 1” without a break. Check 2” without a break.
Note 2: Check that the data of page: 6, address: 02 is “00”. Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON. If not, turn the power of unit OFF/ON.
6-26
DSC-F717
6-27
DSC-F717
19. Auto White Balance 3200K Check 2 RadarW 20. Auto White Balance 3200K Check 3
RadarW
RadarW
Mode CAMERA Mode CAMERA
Subject Clear chart Subject Clear chart
(Standard picture frame with the (Standard picture frame with the
zoom lens at WIDE end) zoom lens at WIDE end)
Measurement Point Displayed data of page: F, address: Measurement Point Displayed data of page: F, address:
7C, 7D 82, 83
Measuring Instrument Adjusting remote commander Measuring Instrument Adjusting remote commander
Specified Value 1 00 to 2F, EE to FF Specified Value 1 00 to 82, E7 to FF
Specified Value 2 00 to 23, F6 to FF Specified Value 2 00 to 6D, F1 to FF
Note 1: Perform this check after “Auto white Balance 3200K Note 1: Perform this check after “Auto white Balance 3200K
Check 1” without a break. Check 2” without a break.
Note 2: Check that the data of page: 6, address: 02 is “00”. Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON. If not, turn the power of unit OFF/ON.
6-28
DSC-F717
Note 1: “Auto White Balance 3200K Standard Data Input” and Fig. 6-1-16
“Auto White Balance 5800K Standard Data Input” need
to be adjusted beforehand.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 3: “Color Reproduction Adjustment” is available only once
after the power is turned on. Turn the power off, then on
again if the adjustment is retried.
Adjusting method:
Order Page Address Data Procedure
Perform “Data setting during
1 camera system adjustment”.
(Refer to page 6-14)
Perform “Picture Frame
2
Setting”. (Refer to page 6-15)
3 6 01 AB Press PAUSE button.
4 6 12 80
5 Wait for 1 second.
6 6 12 00
7 Wait for 2 seconds.
8 6 37 1F
9 6 01 A9 Press PAUSE button. (Note 4)
Check the data changes to
10 6 02
“01”.
Check the each color lumi-
11 nance point is in each color
reproduction frame.
Note 4: The adjustment data will be automatically input to page:
F, address: A4 to AF.
6-29
DSC-F717
Adjusting method:
Order Page Address Data Procedure
Perform “Data setting during
1 camera system adjustment”.
(Refer to page 6-14)
2 E 64 Note down the data.
3 E 64 1E Press PAUSE button.
4 E 69 Note down the data.
5 E 69 16 Press PAUSE button.
6 6 01 8B Press PAUSE button.
Check the data changes to
7 6 02
“01”.
Check the data.
8 6 55 00 to 7F: Normal
80 to FF: Defective
9 6 01 00 Press PAUSE button.
10 E 64 0F Press PAUSE button.
11 E 69 60 Press PAUSE button.
12 6 01 87 Press PAUSE button.
Check the data changes to
13 6 02
“01”.
Check the data.
14 6 55 00: Normal
01 to FF: Defective
6-30
DSC-F717
23. CCD Black Defect Compensation RadarW Processing after Completing Adjustment:
Mode CAMERA Order Page Address Data Procedure
Subject Clear chart 1 6 01 00 Press PAUSE button.
(Standard picture frame with the 2 6 2C 00
zoom lens at WIDE end)
3 6 30 00
Measurement Point Displayed data of page: 6,
4 6 91 00
address: 55
Set data noted down at step
Measuring Instrument Adjusting remote commander 5 E 65
2, and press PAUSE button.
Note 1: Check that the data of page: 6, address: 02 is “00”.
Release the data setting
If not, turn the power of unit OFF/ON.
6 performed at step 1.
Note 2: Check that there are no dust, no dirt and reflection of the
(Refer to page 6-14)
clear chart.
Note 3: Any subject other than the clear chart should be in the
screen.
Adjusting method:
Order Page Address Data Procedure
Perform “Data setting during
1 camera system adjustment”.
(Refer to page 6-14)
2 E 65 Note down the data.
3 E 65 4C Press PAUSE button.
4 6 2C 01
5 6 90 00
6 6 91 03
7 6 92 00
8 6 93 00
9 6 01 79 Press PAUSE button.
10 6 30 08
Check the data changes to
11 6 07
“01”.
12 6 01 8D Press PAUSE button.
Check the data changes to
13 6 02
“01”.
Check the data.
00 to 14 : Normal
14 6 55
15 to FF : Defective
(Note 4)
15 6 01 00 Press PAUSE button.
16 E 65 5A Press PAUSE button.
17 6 01 89 Press PAUSE button.
Check the data changes to
18 6 02
“01”.
Check the data.
19 6 55 00: Normal
01 to FF: Defective
Note 4: If the data is “00” at the check in this adjustment method
order #14, skip the orders from #15 to #19, and go for-
ward to “Processing after Completing Adjustment.
6-31
DSC-F717
24. CCD Linearity Check (Monitoring) Order Page Address Data Procedure
Check that CCD output at monitoring keeps being straight even
24 1 Read displayed data. (Note 1)
input is changed.
Get average value of
Mode CAMERA displayed data of ten times,
25
Subject Clear chart and named average value as
(Standard picture frame with the DB/GHi.
zoom lens at WIDE end) Convert DB/GHi to decimal
26
Measurement Point Displayed data of Page: 1 (Note 1) notation, and obtain DB/GHi’.
Measuring Instrument Adjusting remote commander Set data noted down at step
27 B 72
Specified Value 1 97 to 103 (decimal notation) 16, and press PAUSE button.
Note 1: The right four digits of the page: 1 displayed data of the 29 Wait for 2 seconds.
adjusting remote commander. 30 0 03 40
1:XX:XX 31 1 Read displayed data. (Note 1)
Displayed data
Get average value of
Adjusting method: displayed data of ten times,
32
and named average value as
Order Page Address Data Procedure DR/GLow.
Perform “Data setting during Convert DR/GLow to decimal
1 camera system adjustment”. 33
notation, and obtain DR/GLow’.
(Refer to page 6-14)
34 0 03 41
Perform “Picture Frame
2 35 1 Read displayed data. (Note 1)
setting”. (Refer to page 6-15)
3 7 09 04 Press PAUSE button. Get average value of
displayed data of ten times,
4 6 C8 26 36
and named average value as
5 6 13 A8 DB/GLow.
6 6 14 90 Convert DB/GLow to decimal
37
7 Wait for 2 seconds. notation, and obtain DB/GLow’.
6-32
DSC-F717
6-33
DSC-F717
25. CCD Linearity Check (Caputure) Order Page Address Data Procedure
Check that CCD output at caputure keeps being straight even in-
Convert DB/GHi to decimal
put is changed. 31
notation, and obtain DB/GHi’.
Mode CAMERA 32 6 01 00 Press PAUSE button.
Subject Clear chart Set data noted down at step
(Standard picture frame with the 33 B 72
19, and press PAUSE button.
zoom lens at WIDE end)
34 6 14 8B
Measurement Point Displayed data of Page: 1 (Note 1)
35 Wait for 2 seconds.
Measuring Instrument Adjusting remote commander
36 6 01 F9 Press PAUSE button.
Specified Value 97 to 103 (decimal notation)
37 Wait for 3 seconds.
Note 1: The right four digits of the page: 1 displayed data of the
adjusting remote commander. 38 0 03 40
1:XX:XX 39 1 Read displayed data. (Note 1)
Displayed data 40 This data is named DR/GLow.
Convert DR/GLow to decimal
Adjusting method: 41
notation, and obtain DR/GLow’.
Order Page Address Data Procedure
42 0 03 41
Perform “Data setting during
43 1 Read displayed data. (Note 1)
1 camera system adjustment”.
(Refer to page 6-14) 44 This data is named DB/GLow.
Perform “Picture Frame Convert DB/GLow to decimal
2 45
setting”. (Refer to page 6-15) notation, and obtain DB/GLow’.
3 7 09 04 Press PAUSE button. Calculate D1 by using the
following equation. (decimal
4 6 C8 26 46
calculation)
5 6 13 A8 D1 = (DR/GHi’ ÷ DR/GRef’) × 100
6 6 14 90 Check that calculated D1
47
7 Wait for 2 seconds. satisfies the specified value.
8 6 01 F9 Press PAUSE button. Calculate D2 by using the
9 Wait for 3 seconds. following equation. (decimal
48
calculation)
10 0 03 40 D2 = (DB/GHi’ ÷ DB/GRef’) × 100
11 1 Read displayed data. (Note 1) Check that calculated D2
49
12 This data is named DR/GRef. satisfies the specified value.
Convert DR/GRef to decimal Calculate D3 by using the
13
notation, and obtain DR/GRef’. following equation. (decimal
50
14 0 03 41 calculation)
D3 = (DR/GLow’ ÷ DR/GRef’) × 100
15 1 Read displayed data. (Note 1)
Check that calculated D3
16 This data is named DB/GRef. 51
satisfies the specified value.
Convert DB/GRef to decimal Calculate D4 by using the
17
notation, and obtain DB/GRef’. following equation. (decimal
52
18 6 01 00 Press PAUSE button. calculation)
19 B 72 Note down the data. D4 = (DB/GLow’ ÷ DB/GRef’) × 100
20 B 72 50 Press PAUSE button. Check that calculated D4
53
satisfies the specified value.
21 Wait for 2 seconds.
22 6 01 F9 Press PAUSE button.
Processing after Completing Adjustment:
23 9 Wait for 3 seconds. Order Page Address Data Procedure
24 0 03 40
1 6 01 00 Press PAUSE button.
25 1 Read displayed data. (Note 1)
2 6 C8 00
26 This data is named DR/GHi. 3 0 03 00
Convert DR/GHi to decimal
27 4 7 09 00 Press PAUSE button.
notation, and obtain DR/GRHi’.
5 6 13 00
28 0 03 41
6 6 14 00
29 1 Read displayed data. (Note 1)
Release the data setting
30 This data is named DB/GHi. 7 performed at step 1.
(Refer to page 6-14)
6-34
DSC-F717
6-35
DSC-F717
Adjusting method:
Order Page Address Data Procedure
Perform “Data setting during
1 camera system adjustment”.
(Refer to page 6-14)
2 F 15 Note down the data.
3 9 62 Note down the data.
4 9 83 Note down the data.
5 F 15 80 Press PAUSE button.
6 9 62 06 Press PAUSE button.
7 9 83 50 Press PAUSE button.
8 6 01 AF Press PAUSE button. (Note 6)
Check the data changes to
9 6 02
“01”.
Check the data.
10 F 13 00: Normal
FF: Defective
Note 6: The adjustment data will be automatically input to page:
F, address: 10 to 16.
6-36
DSC-F717
6-37
DSC-F717
COVER
22
CPC cover
1 CPC-12 jig
(J-6082-436-A)
FR-194 board
CN305
Fig. 6-1-18
6-38
DSC-F717
1. LCD Initial Data Input (1) 2. LCD Initial Data Input (2)
Note: Press the PAUSE button each time the data are set, as the Note: Press the PAUSE button each time the data are set, as the
data are written to non-volatile memory (EEPROM). data are written to non-volatile memory (EEPROM).
6-39
DSC-F717
Pedestal
2H
Fig. 6-1-19
6-40
DSC-F717
A
10 steps peak
2H
A
Fig. 6-1-21
Pedestal
2H
Fig. 6-1-20
6-41
DSC-F717
B A
A B
Fig. 6-1-22
6-42
DSC-F717
COVER
22
CPC cover
1 CPC-12 jig
(J-6082-436-A)
FR-194 board
CN305
Fig. 6-1-23
6-43
DSC-F717
90 30
Fixed value Menu setting:
91 72 1) VIDEO OUT of SET UP setting
92 34 VCO Adjustment (NTSC mode) ......................... NTSC (NTSC mode)
93 44 VCO Adjustment (PAL mode) (This adjustment must be performed in NTSC mode, so don’t
set the menu setting to “PAL” )
94 28 Fixed value
95 7F Bright Adjustment Adjusting method:
96 08 Order Page Address Data Procedure
Fixed value
97 80 1 0 01 01
98 94 2 A 02 23 Press PAUSE button.
White Balance Adjustment
99 82 3 4 F1 13 (NTSC mode)
9A 25 Contrast Adjustment 4 4 1D 82 (PAL mode)
9B 1D Change the data and set the
9C 2B 5 A 92 frequency (f) to the NTSC
Fixed value specified value.
9D 00
A2 30 6 A 92 Press PAUSE button.
Change the data and set the
Processing after Completing Adjustments: 7 A 93 frequency (f) to the PAL
1) Select page: 0, address: 01, and set data: 00. specified value.
8 A 93 Press PAUSE button.
6-44
DSC-F717
Pedestal
10 steps peak
A
Pedestal Pedestal
2H 2H
A: Between the reversed waveform pedestal and non-reversed A: Between the pedestal and 10 steps peak
waveform pedestal
6-45
DSC-F717
Mode PLAY
Signal Arbitrary
Measurement Point Check on EVF screen
Measuring Instrument
Adjustment Page A
Adjustment Address 98, 99
Specified Value EVF screen must not be colored
Adjusting method:
Order Page Address Data Procedure
1 0 01 01
2 A 02 23 Press PAUSE button.
3 4 F1 02
98 94 Press PAUSE button.
4 A
99 82 (Initial value)
Check that the EVF screen is
not colored. If not colored,
5
proceed to “Processing after
Completing Adjustments”.
Change the data so that the
98
6 A EVF screen is not colored.
99
(Note)
Note: To write in the non-volatile memory (EEPROM), press the
PAUSE button each time to set the data.
6-46
DSC-F717
COVER
0 : 00 : 00
Fig. 6-2-1
4) Operate the adjusting remote commander as follows.
• Changing the page
The page increases when the EDIT SEARCH + button is
pressed, and decreases when the EDIT SEARCH – button is
pressed. There are altogether 16 pages, from 0 to F.
Hexadecimal
0 1 2 3 4 5 6 7 8 9 A B C D E F
notation
LCD Display 01 2 3 4 5 6 7 8 9 A b c d E F
Decimal notation
0 1 2 3 4 5 6 7 8 9 10 11 1213 1415
conversion value
Table 6-2-1
6-47
DSC-F717
COVER
(Example) In the case that the adjusting remote control unit display are BD (bd).
As the upper digit of the hexadecimal notation is B (b), and the lower digit is D (d), the intersection “189” of
the1 and 2 in the above table is the decimal notation to be calculated.
Table 6-2-2
6-48
DSC-F717
COVER
0 : 00 : 00
Address
Page
bit3 to bit0 discrimination
bit7 to bit4 discrimination
6-49
DSC-F717
Data Function Bit Function When bit value=1 When bit value=0
00 to 14 S 0 POWER SW OFF ON
15 to 3D A 1 PLAY (Mode Dial) others PLAY
3E to 67 M 2
68 to A8 SCN SHUTTER SW
A9 to D0
D1 to FF
MOVIE
CAMERA
3
(PW51050 block
S401 ) OFF ON
XSHUTTER LOCK SW
Using method:
1) Select page: 2, address: 90.
4
(PW51050 block
S401 )
OFF ON
2) By discriminating the bit value of dispaly data, the state of the MEMORY STICK IN SW
5 OUT IN
switches can be discriminated. (MS Socket)
Using method:
1) Select page: 2, address: 80 and 81.
2) By discriminating the bit value of dispaly data, the state of the
switches can be discriminated.
Using method:
1) Set the mode dial to any position other than “SET UP’”.
2) Select page: 2, address: 81.
3) By discriminating the upper digit of the data, the rotation of
the control dial can be discriminated.
6-50
DSC-F717
Page 2 Address 91 to 95
Using method:
1) Select page: 2, addresses: 91 to 95.
2) By discriminating the dispaly data, the pressed key can be
discriminated.
Data
Address
00 to 14 15 to 3D 3E to 67 68 to A8 A9 to D0 D1 to FF
91 CONTROL DOWN CONTROL UP MENU INDEX FINEDER LCD
(KEY AD0) (SW-379 board) (SW-379 board) (SW-379 board) (SW-379 board) (SW-379 board) (SW-379 board)
(IC102 tg) (S353) (S353) (S352) (S351) (S354) (S354)
92 CONTROL RIGHT CONTROL LEFT CONTROL SET DISPLAY
(KEY AD1) (SW-379 board) (SW-379 board) (SW-379 board) (SW-379 board) No key input
(IC102 th) (S353) (S353) (S353) (S355)
ONE-PUSH FOCUS FOCUS
93 AE LOCK SPOT METER WHT BAL
WHITE BALANCE MANUAL AUTO
(KEY AD2) (FZ51050 block) (FZ51050 block) (FZ51050 block)
(FZ51050 block) (FZ51050 block) (FZ51050 block)
(IC102 tj) (S301) (S302) (S304)
(S303) (S308) (S308)
NIGHT SHOT
+/– JOG DIAL NIGHT FRAMING NIGHT SHOT
94 NIGHT FRAMING
(EXPOSURE) EXECUTE ON ON
(KEY AD3) OFF
(PW51050 block) (PW51050 block) (TY-014 block) (TY-014 block)
(IC102 tk) (TY-014 block)
(S404) (S406) (S301) (S301)
(S301)
ZOOM T ZOOM T ZOOM W ZOOM W
95
(Fast) (Slow) (Fast) (Slow)
(KEY AD4) No key input
(FZ51050 block) (FZ51050 block) (FZ51050 block) (FZ51050 block)
(IC102 tl)
(S306) (S306) (S307) (S307)
8. LED Check
Page 2 Address 04 Data 02
Using method:
1) Select page: 2, address: 04, set data: 02, and press PAUSE
button.
2) Check that all LED are lit.
(SELF TIMER/REC, POWER, CHG, ACCESS LED)
3) Select page: 2, address: 04, set data: 00, and press PAUSE
button.
C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR
Format the “Memory Stick”. Unformatted “Memory Stick” is inserted. FORMAT ERROR
C:13:ss
Insert a new “Memory Stick”. “Memory Stick” is broken. MEMORY STICK ERROR
When failed in the focus and zoom
E:61:ss Checking of lens drive circuit.
initialization.
—
Checking of flash unit or replacement Abnormality when flash is being
E:91:ss
of flash unit. charged.
6-51
DSC-F717
AF ILLUMINATION CHECK Take a reduced or enlarged copy on the clear sheet so that a
rectangular frame of the SHEET FOR AUXILIARY LIGHT
is suitable for the effective image size of the monitor.
DSC-F717
6-52
DSC-F717
R-Y
MG
R
YE
W
B-Y
B
G
CY
✄ DSC-F717
✄
6-53 E
Reverse 992999451.pdf
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2002.09 Official Release — —