Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Ingeniería de Sistemas
Palmira
2018
Trabajo de Grado-Diplomado De Profundización Cisco (Diseño E
Implementación De Soluciones Integradas Lan / Wan)
Tutor:
Giovanni Alberto Bracho
Ingeniería de Sistemas
Palmira
2018
Tabla De Contenido
Introducción .................................................................................................................................5
1. Desarrollo Prueba Final De Habilidades Prácticas-CCNA 1 y 2 ....................................7
1.1 Configurar el direccionamiento IP acorde con la topología de red para cada uno de
los dispositivos que forman parte del escenario .......................................................................8
1.2 Configurar el protocolo de enrutamiento OSPFv2 bajo los siguientes criterios: ......... 17
1.3 Configurar VLANs, Puertos troncales, puertos de acceso, encapsulamiento, Inter-
VLAN Routing y Seguridad en los Switches acorde a la topología de red establecida. .... 23
1.4 En el Switch 3 deshabilitar DNS lookup ...................................................................... 26
1.5 Asignar direcciones IP a los Switches acorde a los lineamientos. .......................... 26
1.6 Desactivar todas las interfaces que no sean utilizadas en el esquema de red. ... 27
1.7 Implement DHCP and NAT for IPv4 ............................................................................ 31
1.8 Configurar R1 como servidor DHCP para las VLANs 30 y 40.................................. 31
1.9 Reservar las primeras 30 direcciones IP de las VLAN 30 y 40 para configuraciones
estáticas....................................................................................................................................... 31
1.10 Configurar NAT en R2 para permitir que los host puedan salir a internet .............. 33
1.11 Configurar al menos dos listas de acceso de tipo estándar a su criterio en para
restringir o permitir tráfico desde R1 o R3 hacia R2. ............................................................. 33
1.12 Configurar al menos dos listas de acceso de tipo extendido o nombradas a su
criterio en para restringir o permitir tráfico desde R1 o R3 hacia R2. .................................. 34
1.13 Verificar procesos de comunicación y redireccionamiento de tráfico en los routers
mediante el uso de Ping y Traceroute. .................................................................................... 34
Conclusiones ............................................................................................................................ 40
Tabla de Ilustraciones
Topología de red
PC-A
Figure 3 configuración red PC-A
PC-C
Figure 4 Configuración red PC-C
INTERNET-PC
Figure 5 Configuración red Intrernet-PC
WEBSERVER
Router#no ip dom
Router#no ip domain-lookup
^
% Invalid input detected at '^' marker.
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#no ip domian-lookup
^
% Invalid input detected at '^' marker.
Router(config)#no ip domain-lookup
Router(config)#hostname R1
R1(config)#enable secret class
R1(config)#line con 0
R1(config-line)#pass cisco
R1(config-line)#login
R1(config-line)#line vty 0 4
R1(config-line)#pass cisco
R1(config-line)#login
R1(config-line)#service
^
% Invalid input detected at '^' marker.
R1(config-line)#exit
R1(config)#service
R1(config)#service p
R1(config)#service password-encryption
R1(config)#int s0/1/0
R1(config-if)#description conexion con R2
R1(config-if)#ip address 172.31.21.1 255.255.255.252
R1(config-if)#clock rate 128000
R1(config-if)#no shu
Configuración router 2
Router>conf t
^
% Invalid input detected at '^' marker.
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#no ip domain-lookup
Router(config)#hostname R2
R2(config)#enable secret class
R2(config)#line con 0
R2(config-line)#pass cisco
R2(config-line)#login
R2(config-line)#line vty 0 4
R2(config-line)#pass cisco
R2(config-line)#login
R2(config-line)#exit
R2(config)#service
R2(config)#service p
R2(config)#service password-encryption
R2(config)#int s0/0/0
R2(config-if)#description conexion con R1
R2(config-if)#ip address 172.31.21.2 255.255.255.252
R2(config-if)#no shu
R2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R2(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state
to up
exit
R2(config)#int s0/0/1
R2(config-if)#description conexion con R3
R2(config-if)#ip address 172.31.23.1 255.255.255.252
R2(config-if)#clock rate 128000
R2(config-if)#no shu
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R2(config-if)#int g0/0
R2(config-if)#descrip conexion a isp
R2(config-if)#ip address 209.165.200.225 255.255.255.248
R2(config-if)#no shu
R2(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
R2(config-if)#int g0/1
R2(config-if)#ip address 10.10.10.1 255.255.255.0
R2(config-if)#no shu
R2(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
Configuración router 3
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#no ip damain-lookup
^
% Invalid input detected at '^' marker.
Router(config)#no ip domain-lookup
Router(config)#hostname R3
R3(config)#enable secret class
R3(config)#line con 0
R3(config-line)#pass cisco
R3(config-line)#login
R3(config-line)#line vty 0 4
R3(config-line)#pass cisco
R3(config-line)#login
R3(config-line)#exit
R3(config)#serv
R3(config)#service p
R3(config)#service password-encryption
R3(config)#
R3>en
Password:
R3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#int s0/1/1
R3(config-if)#descrip conexion a R2
R3(config-if)#ip address 172.31.23.2 255.255.255.252
R3(config-if)#no shu
R3(config-if)#
%LINK-5-CHANGED: Interface Serial0/1/1, changed state to up
R3(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1/1, changed state
to up
R3(config-if)#int lo4
R3(config-if)#
%LINK-5-CHANGED: Interface Loopback4, changed state to up
R3(config-if)#
%LINK-5-CHANGED: Interface Loopback5, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback5, changed state
to up
R3(config-if)#
%LINK-5-CHANGED: Interface Loopback6, changed state to up
Configuración S1
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S1
S1(config)#enable secret class
S1(config)#no ip domain-lookup
S1(config)#line con 0
S1(config-line)#pass cisco
S1(config-line)#line vty 0 4
S1(config-line)#pass cisco
S1(config-line)#login
S1(config-line)#line con 0
S1(config-line)#login
S1(config-line)#ser
S1(config-line)#serv
S1(config-line)#exit
S1(config)#serv
S1(config)#service p
S1(config)#service password-encryption
S1(config)#
S1#
%SYS-5-CONFIG_I: Configured from console by console
Configuración S3
Switch>EN
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no ip domain-lookup
Switch(config)#hostname S3
S3(config)#enable secret class
S3(config)#line con 0
S3(config-line)#pass cisco
S3(config-line)#login
S3(config-line)#line vty 0 4
S3(config-line)#pass cisco
S3(config-line)#login
S3(config-line)#exit
S3(config)#serv
S3(config)#service p
S3(config)#service password-encryption
S3(config)#
OSPFv2 area 0
Configuration Item or Task Specification
Router ID R1 1.1.1.1
Router ID R2 2.2.2.2
Router ID R3 3.3.3.3
Configurar todas las interfaces LAN como
pasivas
Establecer el ancho de banda para enlaces 128 Kb/s
seriales en
Ajustar el costo en la métrica de S0/0 a 7500
R1
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config-router)#network 172.31.21.0 0.0.0.3 area 0
R1(config-router)#network 192.168.30.0 0.0.0.255 area 0
R1(config-router)#network 192.168.40.0 0.0.0.255 area 0
R1(config-router)#network 192.168.200.0 0.0.0.255 area 0
R1(config-router)#passive-interface g0/1.30
R1(config-router)#passive-interface g0/1.40
R1(config-router)#passive-interface g0/1.200
R1(config-router)#exit
R1(config)#int s0/1/0
R1(config-if)#ban
R1(config-if)#bandwidth 128
R1(config-if)#ip ospf cost 7500
R1(config-if)#
R2
R2>en
Password:
R2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#router ospf 1
R2(config-router)#router id 2.2.2.2
^
% Invalid input detected at '^' marker.
R2(config-router)#router-id 2.2.2.2
R2(config-router)#network 172.31.21.0 0.0.0.3 area 0
R2(config-router)#
04:29:30: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0/0/0 from
LOADING to FULL, Loading Done
R1
R2
R3
R3
R
2
R
3
R1(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
S1
S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#vlan 30
S1(config-vlan)#name Administracion
S1(config-vlan)#vlan 40
S1(config-vlan)#name Mercadeo
S1(config-vlan)#vlan 200
S1(config-vlan)#name Mantenimiento
S1(config-vlan)#
S1(config-vlan)#exit
S1(config)#int vlan 30
S1(config-if)#
%LINK-5-CHANGED: Interface Vlan30, changed state to up
S1>en
Password:
Password:
S1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)#int f0/3
S1(config-if)#switchport mode trunk
S1(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,
changed state to down
S3
S3>en
Password:
S3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S3(config)#
S3(config)#vlan 40
S3(config-vlan)#name Mercadeo
S3(config-vlan)#vlan 30
S3(config-vlan)#name Administracion
S3(config-vlan)#vlan 200
S3(config-vlan)#name Mantenimiento
S3(config-vlan)#exit
S3(config)#int vlan 30
S3(config-if)#
%LINK-5-CHANGED: Interface Vlan30, changed state to up
S3(config)#
%LINEPROTO-5-UPDOWN: Line
protocol on Interface Vlan30, changed
state to up
S1
S1(config-if)#int range fa0/1-2, fa0/4, fa0/7-24,g0/1-2
S1(config-if-range)#shutdown
S3
S3(config-if)#int range f0/1-2, f0/4-17, f0/19-24,g0/1-2
S3(config-if-range)#shutdown
R1
R1>en
Password:
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#ip dhcp e
R1(config)#ip dhcp excluded-address 192.168.30.1 192.168.30.30
R1(config)#ip dhcp excluded-address 192.168.40.1 192.168.40.30
R1(config)#
Name:
Configurar DHCP pool para VLAN ADMINISTRACIO
30 N DNS-Server:
10.10.10.11
Domain-Name: ccna-unad.com
Establecer default gateway.
R2
LSITA DE ACCESO QUE PERMITE A LOS HOST ENTRAR AL SERVIDOR WEB
A TRAVES DE WWW MEDIANTE LA NAT
R2(config)#int g0/0
R2(config-if)#ip
R2(config-if)#ip ac
R2(config-if)#ip access-group 101 in
R2(config-if)#int s0/0/0
R2(config-if)#ip access-group 101 out
R2(config-if)#int s0/0/1
R2(config-if)#ip access-group 101 out
R2(config-if)#int g0/1
R2(config-if)#ip access-group 101 out
R2(config-if)#
R1 A R2
Figure 8 Ping R1 a R2
R2 A R3
Figure 9 Ping R2 a R3
PC
INTERN
ET A
INTERN
ET
S1 al R1
Figure 12 Ping S1 a R1
PC-A
HACIA
PC-C
PING
PC-C A
WEB-
SERVE
R
NUNSYS. Lo que debes saber sobre el Switching y el Routing. enero 03 del 2017.
(https://nunsys.com/switching-routing/)