Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Units system: SI
Steel connections
Joints summary
___________________________________________________________________________________________________________________________
Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
__________________________________________________________________________________________________________________
Joint : 1 - BCF ()
Design status : With warnings
__________________________________________________________________________________________________________________
Ratio : 0.52
Template(s) : SP BCF
Page1
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
Units system: SI
Steel connections
Loads summary
___________________________________________________________________________________________________________________________
Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
__________________________________________________________________________________________________________________
Joint : 1 - BCF ()
Design status : With warnings
__________________________________________________________________________________________________________________
Ratio : 0.52
Template(s) : SP BCF
Page2
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
Units system: SI
Steel connections
Detailed report
___________________________________________________________________________________________________________________________
___________________________________________________________________________________________________________________________
MEMBERS
Beam
General
Beam section : H200x80x7.5x11 Pos
Beam material : A36
sb: Beam setback : 15 mm
Horizontal angle (deg) : 0
Vertical angle (deg) : 0
Horizontal eccentricity : 0 mm
Coped
dct: Top cope depth : 0 mm
ct: Top cope length : 0 mm
dcb: Bottom cope depth : 0 mm
cb: Bottom cope length : 0 mm
Column
General
Support section : H200x80x7.5x11 Pos
Support material : A36
Is column end : Yes
SINGLE PLATE
Connector
Section : PL 10x105x160
b: Width : 105 mm
L: Length : 160 mm
tp: Plate thickness : 10 mm
Material : A36
Plate position on beam : Center
Bolts : M20 A325M
nr: Rows of Bolts : 2
nc: Bolt columns : 1
s: Pitch - longitudinal center-to-center spacing : 80 mm
Lev: Vertical edge distance : 40 mm
Leh: Horizontal edge distance : 40 mm
a: Distance between weld and bolts : 65 mm
Hole type on plate : Standard (STD)
Hole type on beam : Standard (STD)
Welding electrode to support : E70XX
Page1
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
D: Weld size to support (1/16 in) : 4
Wo: Obtuse side weld size (AWS) (1/16 in) : 4
Wa: Acute side weld size (AWS) (1/16 in) : 4
Wo: Obtuse side weld size (AISC) (1/16 in) : 4
Wa: Acute side weld size (AISC) (1/16 in) : 4
DEMANDS
Beam Column
Description Ru Pu Pu Mu22 Mu33 Load type
[KN] [KN] [KN] [KN*m] [KN*m]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CB1 12.00 80.00 0.00 0.00 0.00 Design
CB2 12.00 -80.00 0.00 0.00 0.00 Design
CB3 -12.00 80.00 0.00 0.00 0.00 Design
CB4 -12.00 -80.00 0.00 0.00 0.00 Design
CB5 8.00 50.00 0.00 0.00 0.00 Design
CB6 8.00 -50.00 0.00 0.00 0.00 Design
CB7 -8.00 50.00 0.00 0.00 0.00 Design
CB8 -8.00 -50.00 0.00 0.00 0.00 Design
CB9 8.00 20.00 0.00 0.00 0.00 Design
CB10 8.00 -20.00 0.00 0.00 0.00 Design
CB11 -8.00 20.00 0.00 0.00 0.00 Design
CB12 -8.00 -20.00 0.00 0.00 0.00 Design
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Shear plate
Length [mm] 160.00 77.00 154.00 p. 10-104
Lmin = T/2
= 154[mm]/2
= 77[mm] p. 10-104
Vertical center-to-center spacing (pitch) [mm] 80.00 53.33 180.00 Sec. J3.3,
Sec. J3.5
smin = 8/3*d
= 8/3*20[mm]
= 53.33[mm] Sec. J3.3
IsCorrosionConsidered ® False
Page2
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Beam
Vertical edge distance [mm] 60.00 33.65 -- Tables J3.4,
J3.5
Lemin = edmin + C2
= 33.65[mm] + 0[mm]
= 33.65[mm] Tables J3.4,
J3.5
Support
Weld size [1/16in] 4 4 -- p. 10-101
wmin = (5/8)*tp
= (5/8)*10[mm]
= 6.25[mm] p. 10-101
WARNINGS
- Connector does not fit on beam
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Shear plate
Bolts shear [KN] 155.88 80.89 CB1 0.52 Tables (7-1..14)
(n>=10) and (n<=12) and (IsStandardHole) ® (2>=10) and (2<=12) and (True) ® False
BoltFactor = 1 p. 10-102
fRn = f*Fnv*Ab
= 0.75*330.95[N/mm2]*314[mm2]
= 77.94[kN] Eq. J3-1
fRn = C*fRn*BoltFactor
= 2*77.94[kN]*1
= 155.88[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 249.08 12.00 CB1 0.05 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 40[mm] - 21.59[mm]/2)
= 29.21[mm] Sec. J3.10
Page3
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*1600[mm2]
= 238.28[kN] Eq. J4-3
Le = L - n*Lh
= 160[mm] - 2*23.18[mm]
= 113.65[mm] DG4 Eq. 3-13
Anv = Le*tp
= 113.65[mm]*10[mm]
= 1136.5[mm2] Sec. J4-2
fRn = f*0.60*Fu*Anv
= 0.75*0.60*399.89[N/mm2]*1136.5[mm2]
= 204.52[kN] Eq. J4-4
IsStressUniform ® True
Bolt bearing under axial load [KN] 210.23 80.00 CB1 0.38 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 40[mm] - 21.59[mm]/2)
= 29.21[mm] Sec. J3.10
Page4
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
IsBoltedConnection ® True
Lh = dh + 1/16 [in]
= 21.59[mm] + 1/16 [in]
= 23.18[mm] Sec. D3-2
An = (l - n*Lh)*tp
= (160[mm] - 2*23.18[mm])*10[mm]
= 1136.5[mm2] Sec. D3-2
Ae = min(0.85*Ag, An)
= min(0.85*1600[mm2], 1136.5[mm2])
= 1136.5[mm2] Sec. J4-1
fRn = f*Fu*Ae
= 0.75*399.89[N/mm2]*1136.5[mm2]
= 340.86[kN] Eq. J4-2
Tear out under axial load [KN] 259.79 80.00 CB1 0.31 Eq. J4-5
dhh = dh + 1/16 [in]
= 21.59[mm] + 1/16 [in]
= 23.18[mm] Sec. D3-2
Page5
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
IsStressUniform ® True
N=N
= 80[mm] Sec. J10-2
Beam
Bolt bearing under shear load [KN] 215.94 12.00 CB1 0.06 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 60[mm] - 21.59[mm]/2)
= 49.21[mm] Sec. J3.10
fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*1500[mm2]
= 223.39[kN] Eq. J4-3
Page6
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Bolt bearing under axial load [KN] 211.66 80.00 CB1 0.38 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 50[mm] - 21.59[mm]/2)
= 39.21[mm] Sec. J3.10
Yielding strength due to axial load [KN] 709.82 80.00 CB1 0.11 Eq. D2-1
fRn = f*Fy*Ag
= 0.9*248.21[N/mm2]*3177.5[mm2]
= 709.82[kN] Eq. D2-1
Lh = dh + 1/16 [in]
= 21.59[mm] + 1/16 [in]
= 23.18[mm] Sec. D3-2
An = Ag - nh*tp*Lh
= 3177.5[mm2] - 2*7.5[mm]*23.18[mm]
= 2829.88[mm2] Sec. D3-2
U = 1 - x/l
= 1 - 12.18[mm]/80[mm]
= 0.848 Table D3.1
Ae = U*An
= 0.848*2829.88[mm2]
= 2398.96[mm2] Sec. D3-3
fRn = f*Fu*Ae
= 0.75*399.89[N/mm2]*2398.96[mm2]
= 719.5[kN] Eq. J4-2
Tear out under axial load [KN] 211.59 80.00 CB1 0.38 Eq. J4-5
dhh = dh + 1/16 [in]
= 21.59[mm] + 1/16 [in]
= 23.18[mm] Sec. D3-2
Page7
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
IsStressUniform ® True
Support
Welds rupture [KN/m] 2639.30 225.95 CB1 0.09 p. 9-5
Rn = 0.6*Fu*tp
= 0.6*399.89[N/mm2]*11[mm]
= 2.64[kN/mm] p. 9-5
Dmin = P/(f*C*C1*L)
= 40.45[kN]/(0.75*0.485[kN/mm]*1*160[mm])
= 0.695 tables 8-4..11
HasWeldsOnBothSides ® False
1/2
Ru = 0.6*FEXX*(2) /2*Dmin/16 [in]
1/2
= 0.6*482.63[N/mm2]*(2) /2*0.695/16 [in]
= 0.226[kN/mm] p. 9-5
NOTATION
Ab: Nominal bolt area
Ae: Effective net area
Ag: Gross area
Agv: Gross area subject to shear
An: Net area
Ant: Net area subject to tension
Anv: Net area subjected to shear
fRn: Available shear strength per bolt
N: Bearing length
BoltFactor: Bolt capacity factor
C: Bolt group coefficient
C1: Electrode strength coefficient
C2: Edge distance increment
C: Weld group coefficient
d: Nominal bolt diameter
dcb: Bottom cope depth
dct: Top cope depth
dh: Nominal hole dimension
d: Beam depth
dhh: Horizontal hole dimension
dhv: Vertical hole dimension
D: Number of sixteenths of an inch in the weld size
Dmin: Number of sixteenths of an inch in the minimum weld size
E: Elastic modulus
FEXX: Electrode classification number
Fnv: Nominal shear stress
Fu: Specified minimum tensile strength
Fy: Specified minimum yield stress
Page8
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
NOTATION
Fyw: Specified minimum yield stress of web
g: Transversal gage between bolts
HasWeldsOnBothSides: Has welds on both sides
IsBeamReaction: Is beam reaction
IsBoltedConnection: Is bolted connection
IsCorrosionConsidered: Is corrosion considered
IsStandardHole: Is standard hole (STD)
IsStressUniform: Is the stress uniform
k1: Bearing factor
k2: Bearing factor
kBot: Outside corner radius of the bottom flange
kTop: Outside corner radius of the top flange
l: Length
L: Length
Lc-end: Clear distance
Le: Effective length
Le: Edge distance
Leh: Horizontal edge distance
Lemin: Minimum horizontal edge distance
Lemin: Minimum edge distance
Lev: Vertical edge distance
Lh: Hole dimension for tension and shear net area
Lmax: Maximum length
Lmin: Minimum length
Lp: Plate length
L: Length of weld
edmin: Minimum edge distance
n: Bolts rows number
N: Bearing length
nc: Number of bolt columns
nh: Holes number
P: Required axial force
f: Design factors
fRn: Design or allowable strength
Rn: Nominal strength
Ru: Required strength
smax: Maximum spacing
smin: Minimum spacing
spa: Transversal spacing between bolts or welds
s: Longitudinal bolt spacing
Lc-spa: Distance between adjacent holes edges
tp: Thickness of the connected material
T: Clear distance between web fillets
tf : Thickness of the loaded flange
tp: Plate thickness
tpmax: Maximum plate thickness
tw: Web thickness
U: Shear lag factor
Ubs: Stress index
wmin: Minimum weld size required
x: Connection eccentricity
Page9
60006-POS-CAL-SF-No1-C1,2,3-BCF-H200x80x7_5x11-R0
Units system: SI
Steel connections
Connections elements summary
___________________________________________________________________________________________________________________________
CONNECTION ELEMENTS
Plates
ID Plate Material Length Width Thickness Qty.
[mm] [mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
P0 PL 10x105x160 A36 160.00 105.00 10.00 1
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Bolts
ID Bolt Grade Length Diameter Qty.
[mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
B0 M20 A325M G8_8 17.50 20.00 2
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Welds
ID Weld Type Strength Size Length
[KN/mm2] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
W0 E70XX Fillet 0.48 6[mm] 320.00
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Element Description ID
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Right side
Bolts - Beam side M20 A325M B0
Plate - Support side PL 10x105x160 P0
Weld - Support side E70XX W0
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Notes
Joint type:
BCF : Beam - Column flange
Connector type:
SP : Single plate
Page1