Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Ericsson SingTel
Dafault Recommended
Parameter Description Range Value Value Remarks
BSPWRB Base Station output power 0 -> 63 dbm 45 45 dBm Note that RBS2301 and 2302 only can supports till 33dbm
900: 31
GSM 1800: 33toto47dbm
45dbmInInodd
odd
values only
Base Station output power for the non-BCCH RF
BSPWRT channel numbers 0 -> 63 dbm 45 Note that RBS2301 and 2302 only can supports till 33dbm
GSM 900: 31 to 47dbm In odd
values only
GSM 1800: 33 to 45dbm In odd
values only
Cell Global Identity (conisists of MCC-MNC-LAC-
CGI CI)
MCC - Mobile Country Code MCC : 3 digits - Parameter is only allowed to be change in cell state HALTED
MNC : 2 or 3 digits depending
MNC - Mobile Network Code Mncdigithand) -
LAC - Location Area Code LAC: 1 to 65535 -
CI - Cell Identity CI : 0 to 65535 -
BCCHNO Absolute RF channel number for BCCH 1 to 124( GSM900) - - Bcch - Broadcast Control Channel
512 to 885 (GSM1800) - -
BCCHTYPE Type of BCCH
1) COMB - indicates that the cell has a combined
BCCH and SDCCH/4
2) COMBC - indicates that the cell has a COMB, COMBC, NCOMB NCOMB NCOMB The BCCH is always allocated to time slot number 0 in the defined ARFCN
combined BCCH and SDCCH/4 with CBCH
subchannel ARFCN - Absolute Radio Frequency Channel Number
3) NCOMB - indicates that the cell does not have
any type of combines BCCH and SDCCH/4 CBCH - is used for transmission of messages when the function
Short Messages Service Cell Broadcast (SMSCB) is activate in the cell
CBCH - Cell Broadcast Channel
Parameter is only allowed to be change in cell state HALTED
0 to 7 if non-combined Bcch is
AGBLK Number of reserved access granted blocks used 1 1 AGBLK Parameter is only allowed to be change in cell state HALTED
0 to 2 if combined Bcch and
SDCCH/4 is used
To prevent that all cells on a site send BCCH channels at the same time it is possible
to define a deviation with respect to the FN generator called FNOFFSET. By using
Frame Number Offset - Indicates the time FNOFFSET on a synchronised two or three sector site the time for decoding BSIC
FNOFFSET difference from the FN generator in the BTS 0 to 1325 TDMA Frames 0 0 TDMA Frame can be reduced. RBS2000 and 200 only support the range 0 to 1023.
STATE Cell or Channel Group state ACTIVE, HALTED - ACTIVE The cell or channel group is active or halted
HOP Frequency hopping status ON, OFF, TCH TCH TCH SDCCHs as well as TCHs can hop.
ON: The hopping status for the channel group is
hopping for TCH and SDCCH A bcch will not hop even if it belongs to a channel group defined as hopping
OFF: The hopping status for the channel group is
non hopping
TCH: The hopping status fpr the channel group is
hopping for TCH only
DCHNO Absolute RF channel number 1 to 124( GSM900) - 32 ARFCN GSM900: max 31 DCHNO, GSM1800: max 31 DCHNO, GSM1900: max 31 DCHNO
Related to BCCH plan 512 to 885 (GSM1800)
SDCCH Required number of SDCCH/8 0 to 16 1 1 sdcch Refer to notes for different types of configurations
SCHO SDCCH handover switch ON, OFF OFF OFF ON - handovers on SDCCH are allowed; OFF - handovers on SDCCH are not allowed
DTXD Discontinuous Transmission Downlink ON, OFF OFF OFF Note: ON: DTX DL is enabled for the cell; OFF: DTX DL is disabled for the cell
DTXU Uplink DTX indicator 0 to 2 1 1 Uplink discontinuous transmission means that the MS does not
0: The MSs may use uplink discontinuous
transmission transmit continuously, but only when necessary, thus being able
MAIO Mobile Allocation Index Offset 0 to 15 or DEFAULT DEFAULT DEFAULT SingTel using Baseband Hopping for GSM900 System, RF Hopping for GSM1800
FHOP Frequency Hopping BB, SY BB
BB: Baseband hopping
SY: Synthesiser hopping
A cell is divided into one or more channel groups
which contain all physical channels on an arbitrary
number of frequencies. Cells with a subcell 0 (for cells without a subcell structure).
structure must have at least one channel group n/a (for overlaid subcells).
CHGR defined in each subcell. 0 to 15 0 0 0 (for underlaid subcells).
Subcell type. SingTel does not use Intelligent UL The subcell type is underlaid.
SCTYPE Underlay Overlay [IUO] UL, OL - - OL The subcell type is overlaid.
The HCS feature with 3 layers allows building a network in a two- or three-layered
Defines which cell layers belong to the specified structure. The higher layers can for example be used for large cells and the lower for
HSCBAND. Layer 1 has the highest priority small cells. Cells in layer 1 have higher priority than cells in layer 2, which in turn have
LAYER (microcell) 1 to 8 2 1 /2 higher priority than cells in layer 3.
The signal strength threshold is used for ranking
LAYERTHR of cells in different layer within each HCSBAND 0 to 150 dbm 75 75 dBm / 95 dBm
DOUBLE BA List
MBCCHNO is the BCCH allocation, i.e. it indicates to the MS the frequencies that
Absolute RF channel number for measurement on must be monitored and measured in idle, active or both modes.Up to 32 BCCH carriers
MBCCHNO BCCH 1 to 124 (GSM900) - 32 BCCH in the List can be defined by specifying their ARFCN
Extended range
Radio Link Time-out - the maximum value of the RLINKUP is used by the BSC to determine when to disconnect the call upon
RLINKUP radio counter for the uplink 1 to 63 SACCH periods (480ms) 16 16 repeated failure in decoding the SACCH.
MS power control
DMPSTATE Dynamic MS power control state ACTIVE, INACTIVE INACTIVE ACTIVE
Handover Failure
PSSHF Signal strength penalty at handover failure 0 to 63 db 63 dB 63 dB
PTIMHF Penalty time at handover failure 0 to 600 seconds 15 15
ACTIVE: The measurements made are used for statistical purposes and at channel
allocation.
PASSIVE: No idle channel measurements are made.
ICMSTATE Idle Channel Measurement State ACTIVE, PASSIVE, NOALLOC PASSIVE ACTIVE NOALLOC: The measurements are used for statistical purposes only.
CLSRAMP Cell load sharing ramping time parameter. 0 to 30 seconds 5 seconds 5 The interval during which value of RHYST is ramped up from zero to the final value.
Ericsson 3
Signal strength hysteresis when evaluating high
HIHYST signal strength cells 0 to 63 db 5 dB 5 dB
Signal strength hysteresis when evaluating low
LOHYST signal strength cells 0 to 63 db 3 dB 3 dB