Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
START
NO
Does the Radio
POWER UP and
GO TO
" NO POWER UP "
ZAP
STAY ON ? on page 4 . TEST
SEQUENCE
YES
NO
Does DISPLAY GO TO "NO
works Ok ? DISPLAY" on page
19.
YES
YES GO TO
Does Display shown Display shown
"PHONE FAILURE "PHONE FAILURE SEE
SEE SUPPLIER" ? SUPPLIER"
on page 21 .
NO
YES
GO TO
Does Display shown
"CHECK CARD"
"CHECK CARD" ?
on page 23 .
NO
YES
YES
to
A page 2
A
ZAP
TEST
SEQUENCE
Does the phone NO GO TO
initiate a CALL
" NO TX (DCS mode) "
using a DCS traffic
on page 13 .
channel ?
YES
NO
Is Ringer tone GO TO
audible ? " NO/LOW RINGER "
on page 20 .
YES
ANSWER CALL .
Is Phase NO GO TO
Frequency within " PHASE ERROR "
Spec. ? on page 19 .
YES
Is the Frequency NO GO TO
error within " FREQUENCY ERROR "
specification ? on page 21 .
YES
to
B page 3
B
ZAP
TEST
SEQUENCE
NO GO TO
Is the Power Burst
" POWER BURST ERROR "
within Spec. ?
on page 21 .
YES
NO
Is the TX Audio OK GO TO " NO MIC "
( MIC ) ? on page 21 .
YES
NO
Is the RX Audio OK ? GO TO " NO/LOW AUDIO "
( Loudspeaker ) on page 20 .
YES
TERMINATE THE
CALL .
Listening the NO GO TO
Message . " NO VOICE ANNOTATION "
Is it OK ? on page 22 .
YES
END
START
The phone
Download in to Emmibox
PWR UP correctly
the correct software for Zap.
. NO POWER UP
Connect the phone with EMMIBOX END
cable
and verify if the Zap Loading the
software from EMMIBOX.
YES
Make a SHORT C.
between TP1(L2.75)
and
TP18(WATCHDOG)
YES
YES
NO NO
Check U220,Y702,CR221
Is present the
Is 13 Mhz present and 13 Mhz components
13Mhz on pin
on pin 37 of U703 ? (NOTE 1 and for faulty)
17 of BIC ?
if OK Replace U220 .
YES
YES
to
A page 5 NOTE 1 : CHECK THE COMPONENT/S FOR PHYSICALLY DAMAGE
DRY JOINT AND GOOD POSITION .
A from
page 4
NO POWER UP
NO
Does the RESET
line on pin 30 of Probably U701 Faulty .
U900 go high ?
YES
OK
OK
OK
NOT OK
Is the RESET Probably U704 Faulty .
Timing on page (FLASH E.)
6 correct ?
OK
The power up RESET sequence is described in the following diagram. Following the activation of the +2.75V
Regulator, the GCAP LITE IC and the 68338 begin a seven state power sequence involving the *RESET line and the
GCAP Lite’s Watchdog input. The figure below depicts the sequence of the states. The figure is not drawn to scale.
State 1
When the GCAP LITE IC detects a power on request (ON/OFF Line ”LOW”), the GCAP LITE will drive the system
*RESET line low. The 68338 Clock line will take approximately 100mS to stabilize after power is applied.
State 2
The 68338, SMoC, and BIC in the radio are connected to the *RESET line. The nominal time *RESET is held low by
the GCAP LITE is 250 milliseconds +/- 50 ms.
State 3
When the GCAP LITE releases *RESET, it is pulled high by an internal resistor. There isa period of approximately
500 nanoseconds when neither the GCAP LITE or 68338 is asserting *RESET.
State 4
When the 68338 reset control logic detects that the system *RESET line is no longer being driven, it drives it low for
an additional 512 cycles (39.6 microseconds). This assertion of *RESET by the 68338 is a feature of the IC and
cannot be modified.
State 5
When the 68338 releases *RESET, it is pulled high by the internal resistor. The 68338 be-gins executing its Boot
Code. If valid code is present, the RESET vector in the radio code is then executed. The Boot Code runs for about 512
cycles (39.6usec) before this new vector is executed.
State 6
The 68338 holds *RESET low for 50usec during this state (an internally generated RE-SET).
State 7
When the 68338 releases *RESET, it is again pulled high by the internal resistor. All the processors in the system,
including the 68338, then begin execution. During this state, the 68338 must drive the GCAP Lite’s Watchdog line
START
NO RX
Is a Rx problem
YES
to
only using GSM A page 8
Band ?
NO
YES
Is a Rx problem
only using DCS
Band ?
B to
page 8
NO
Connect on J600 a RF Signal of -30dbm at Frequency of 947.4 Mhz.
Put the phone in TEST mode and digit 45062#
YES
YES
YES
YES
YES
Is the signal at
NO
Replace
base of Q480
FL480
correct ?
YES
from
A page 7
NO RX
Connect on J600 a RF
signal (RX)
of -30dbm at Frequency GO TO "NO MAIN
947.4 Mhz ; put the VCO" gsm mode
Phone in Test Mode and
digit 45062# .
NO
NO
NO
Connect on J600 a
NO
RF signal (RX) of -50dbm
GO TO "NO MAIN at Frequency of
VCO" dcs mode 1842.8Mhz,
Check for dry joint or put the Phone in Test
faulty U401,U403 and and digit 45700# .
J600.
NO
NO
Check the Bias on collector of Q430 (RX2.75) and
YES
the MUTE signal from Q431 ;
Is there on base of Q430
if they are correct, replace Q430,
the RX signal ?
if they aren't correct check Q431 and Q412
for faulty.
NO
NO
from
C page 7 NO RX
YES
Set RF Generation to
-100dbm Level and
digit on Zap 25000# NOT OK Check
then verify the correct L221,C230,U220 for
presence of RXQ and Faulty .
RXI on pin 46 and 47
of U220 .
OK
Is the IQREF NO
signal present on
pin 47 of U220 ?
(about 1.3V c.c.)
YES NOT OK
Check U220 for dry joint Check the following Bias on U220:
OK problem then if OK turn
Check RX L.O. on pin OK pin 35,34,49 = RX_2.75
41 of U220 the Phone NOT in Test from Q221
( signal at 430 Mhz) Mode and check data on pin 11 = R4.75 from U900 .
pin 52,53 of U220. If they are OK replace U220 .
(signal from U500)
E
NOT OK
Is there TX NO
Frequency but to
the Level is G page 12
LOW ?
NO to
page 11
Do you have the
YES Is present at Pin YES
Correct Level and
2,3,4 of U301
Frequency of TX
Signal (902.4 Mhz)
the correct level E
of Tx signal ?
on Pin 8 of U301 ?
from L
NO page 12
from
E page 10
NO TX
GSM MODE
YES
Is correct the
NO
level at output
Replace FL301
of FL301 ?
YES
from
H page 10
PIN 14 = DET_SW from SMOC PIN 14 PIN 14 , 4 = TX_EN from Q501 (as Bias)
If NOT OK go to NOTE 1
U340
PIN 12 = SAT_DET ( saturation signal ) PAC IC PIN 8 , 9 = AOC from PIN 39 of SMOC
to SMOC. If NOT OK go to NOTE 1 (PWR_CNTRL) If NOT OK go to NOTE 1
from
G page 10
NO TX
GSM MODE
YES
Are there on TP13
about 1.2V and the
340 Mhz ?
NO
NO YES
Is there on Pin 4 of Check U220 for dry
Is there the 340 Mhz
U370 the 170 Mhz joint then replace it .
on Pin 6,7 of U220 ?
from Pin 4 of U220 ?
YES NO
U370
TIC IC PIN 2 , 12 = R2.75 from Pin 28 of U900(GCAP)
Is there TX NO
Frequency but to
the Level is G page 15
LOW ?
NO to
page 14
Do you have the
YES Is present at Pin YES
Correct Level and
2,3,4 of U301
Frequency of TX
Signal (1747.8 Mhz)
the correct level E
of Tx signal ?
on Pin 8 of U301 ?
from
L
NO page 15
from
E page 13 NO TX
DCS MODE
YES
Is correct the
NO
level at output
Replace FL301
of FL301 ?
YES
from
H page 13
PIN 14 = DET_SW from SMOC PIN 14 PIN 14 , 4 = TX_EN from Q501 (as Bias)
If NOT OK go to NOTE 1
U340
PIN 12 = SAT_DET ( saturation signal ) PAC IC PIN 8 , 9 = AOC from PIN 39 of SMOC
to SMOC. If NOT OK go to NOTE 1 (PWR_CNTRL) If NOT OK go to NOTE 1
from
G page 13
NO TX
DCS MODE
YES
Are there on TP13
about 1.5V and the
240 Mhz ?
NO
NO YES
Is there on Pin 4 of Check U220 for dry
Is there the 240 Mhz
U370 the 120 Mhz joint then replace it .
on Pin 6,7 of U220 ?
from Pin 4 of U220 ?
YES NO
U370
TIC IC PIN 2 , 12 = R2.75 from Pin 28 of U900(GCAP)
NO
YES
YES
Is present on NO Is present on NO
pin 21 of U220 Pin 22 of U220 Check R233 and R4.75 (from
the SF_OUT ? the R4.75 ? Pin 41 of U900)
YES YES
Replace
U220
DATA
ARE OK
NO
Q = GSM/DCS MATRIX.
page 18
START
It is probable you have an
NO MAIN
Is present on YES
Pin 26 of U220 the
intermittent problem, VCO
Check U220 and Main VCO DCS MODE
1627.8 Mhz ?
components for dry joint .
NO
YES
YES
Is present on NO Is present on NO
Check R233 and R4.75
pin 21 of U220 Pin 22 of U220
(from Pin 41 of U900)
the SF_OUT ? the R4.75 ?
YES YES
Replace
U220
DATA
ARE OK
NO
Q = GSM/DCS MATRIX.
page 18
NOTE :
- WHEN YOU HAVE A SIGNAL WITH THE SYMBOL STAR ( * ) ES. GSM_*DCS ,
from IT MEANING THAT IF YOU SELECT THE BAND WERE THERE IS THAT SYMBOL ,
page 16/17 Q THE LEVEL WILL BE LOW ; SO IF YOU SELECT THE OTHER BAND THE LEVEL WILL BE HIGH .
( ES. GSM_*DCS SIGNAL IS LOW IF YOU SELECT A DCS CH AND HIGH WITH A GSM CH ) .
GSM_DCS
NOT OK MATRIX
Is there the
Check R118 and the
FLTR_-10 V level
path to U101 Pin 4
ALL MODE
on R118 ?
OK
OK
OK
Is it correct the NO
*GSM_DCS signal Replace
on collector of Q105
Q105 ?
YES
NO
Replace
Q100
NO
START DISPLAY
NO
Replace pcb KEYPAD
Display/Keyboard END
Is still no display ?
NO
YES START
YES
Check Replace pcb
Check on ZAP the REED_SWITCH and Display/Keyboard
correct matching
NO MYLAR Is KEYPAD works
between the Software if OK replace pcb fine?
and the PCB Display END display.
and Reflex the Phone .
Is still NO Display ?
NO
YES
YES
Phase
Error OUT
of Spec.
START
NO YES
Are the TXI and TXQ
Check U500 (NOTE 1) Check U220 (NOTE 1)
signal on pin 61,62,63,64
If OK replace it. If OK replace it.
of U220 correct ?
START
NO
Is present at pin 49 Check U500 (NOTE 1)
of U500 the 1Khz ? If OK replace it .
END
YES
NO
YES NO NO
Replace
Replace Ringer.
LOUDSPEAKER.
Is still NO/LOW Is a ringer problem ? END
Is still NO/LOW
RINGER ?
AUDIO ?
YES YES
NO NO
Is present at pin 6 of Check the components from Is present at pin 21
U900 1Khz ? U500 to U900 (NOTE 1) . of U900 1Khz ?
YES
YES
Is present the 1 Khz on pin 5 of U900 ? Is present the 1 Khz on pin 19 of U900 ?
If OK Check components from Gcap to If OK Check components from Gcap to
Ringer (NOTE 1). Loudspeaker (NOTE 1).
If NOT OK Check U900 (NOTE 1) then If NOT OK Check U900 (NOTE 1) then
Replace it . Replace it .
START
With PCB in Test mode digit : NO MIC
- 434# Audio Signal to Loudspeaker
- 4707# Audio Volume
- 36# Loop Back mode
YES
TX POWER
PHONE FAILED
BURST OUT OF
SEE SUPPLIER
SPEC.
INFO INFO
00 : 03,04 or 05 00 : 07
START
NO
Check on pin 49 of U500 the 1Khz ;
Is present the BF signal If OK check U982 and the relative
(1Khz, with off set of 1.1 V) components (NOTE 1 and faulty) .
on pin 25 of U980 ? If NOT OK check U500 (NOTE1 and faulty)
YES
NO
NO
Is there the BF Is there activity on pin
signal (1Khz) on 8,9,10 of U980 during
pin 20 of U980 the play mode time ?
YES
YES
START
Insert a card and connect to Ground CHECK
the Thermistor line (use C830 PIN) . CARD
NO
Is present and Check VSWITCH
correct the components and U900
VSWITCH Voltage (NOTE 1)
on pin 1 of U902 ? If OK replace U900 .
YES
YES
Is present the
correct voltage on NO
pin 5 of U902 Check U902 (NOTE1)
during the Power If OK replace U902 .
ON instant ?
YES