Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Finishing Load
on floors (50mm screeding and punning)
= (50/1000) x 24
= 1.20 KN/m2
on stair and lobby (50mm screeding and punning+19mm marble)
= (50/1000) x 24 + (19/1000)*27
= 1.71 KN/m2
Note: average finishing load of 1.5 kN/m2 is assigned on all floor slab and 1.0 kN/m2 extra load is
considered for staircase slab.
4.2 Slab Load Calculations
As self-weight of all structural members are calculated and add by analysis software itself, the live load,
floor finishing load and partition load is assigned as per following
Component
First FL. (ST#-01)
Second FL (ST#-02)
Loads (DL+LL) (DL+LL)
Live Load (0.0+2.0) (0.0+2.0)
Finishing Load
(1.5+0.0) (1.5+0.0)
Partition Load
(1.0+0.0) (1.0+0.0)
Total: (2.0+2.5) (2.0+2.5)
Seismic Analysis
The building model has been analyzed as per IS 1893(part-I): 2002 in the analysis software which will
automatically calculate the seismic forces.
4 Load Patterns
Table 4.1 - Load Patterns
Self
Name Type Weight Auto Load
Multiplier
Dead Dead 1
Live Live 0
Superimpose
WL 0
d Dead
Superimpose
PWL 0
d Dead
Superimpose
FF 0
d Dead
IS1893
EQx Seismic 0
2002
IS1893
EQy Seismic 0
2002
Direction = X
Structural Period
Seismic Response
Sa
ZI
Seismic Coefficient, Ah [IS 6.4.2] g
Ah =
2R
Period
W Vb
Direction Used
(kN) (kN)
(sec)
X 0.267 1849.6286 199.7599
Applied Story Forces
Direction = Y
Structural Period
Seismic Response
Sa
ZI
Seismic Coefficient, Ah [IS 6.4.2] g
Ah =
2R
Period
W Vb
Direction Used
(kN) (kN)
(sec)
Y 0.217 1849.6286 199.7599
Applied Story Forces
Load
Joint Unique FX FY FZ MX MY MZ
Story Case/Comb
Label Name kN kN kN kN-m kN-m kN-m
o
Story1 1 1 UDCon2 10.3533 -13.7135 188.3114 -18.3334 -5.7809 0.4424
Story1 2 2 UDCon2 4.9817 -7.7361 266.3681 -9.0006 4.2317 -0.0673
Story1 3 3 UDCon2 -5.6677 -5.2492 153.2055 -20.4831 14.5336 -0.6419
Base 4 12 UDCon2 -2.9628 -5.4331 435.3654 4.1777 -2.39 -0.0665
Base 5 13 UDCon2 -2.3479 -7.195 243.3825 5.7973 -1.7168 -0.1042
Base 6 16 UDCon2 -11.6077 29.4212 232.8824 -18.6737 -5.906 -0.4978
Base 7 15 UDCon2 0.6038 27.4739 300.8888 -18.3354 -1.197 0.3342
Base 8 14 UDCon2 -9.0354 17.241 375.5472 -13.8893 -7.2649 0.024
Base 9 11 UDCon2 -2.1791 -11.5141 522.2074 8.9904 -1.6939 0.0233
Base 10 55 UDCon2 6.999 2.4506 276.395 -1.9903 5.6488 -0.0722
Base 25 24 UDCon2 15.9745 -13.8872 16.0666 -2.244 -0.3332 1.0609
Base 26 39 UDCon2 0 0 0.4305 0.082 0.0297 0
Base 27 25 UDCon2 -5.1117 -11.8585 16.9533 -1.7735 0.1444 0.8267
FIGURES
Beam Design
ETABS 2016 Concrete Frame Design
IS 456:2000 Beam Section Design
Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
228.6 355.6 228.6 0 15 25
Material Properties
Ec (MPa) fck (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
22360.68 20 1 500 500
Section Properties
b (mm) h (mm) dc (mm) Cover (Torsion) (mm)
304.8 304.8 56 30
Material Properties
Ec (MPa) fck (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
22360.68 20 1 500 500
`
Shear force 2-2
Reaction
License #*15TW87FJP94DSKR
17 July 2018
Model Definition
1.1. Connectivity
5 SLAB1
23 COL1
24 COL1
25 COL1
26 COL1
27 COL1
28 COL1
29 COL1
5 SOIL1
4. Model loading
This section provides model loading information, including load patterns, load cases, and load combinations.
6.1. Preferences
Table 25: Design Preferences 01 - Resistance Factors
Table 25: Design
Preferences 01 -
Resistance Factors
GammaStee GammaCon
l c
0E+000 0E+000
No 0.800000 0.250000
6.2. Overwrites
Table 29: Slab Design Overwrites 01 - Strip Based
Table 29: Slab Design Overwrites 01 - Strip Based
Strip Layer DesignType RLLF IgnorePT RebarMat
5 FE 500
5 1.000000 Yes No
Table 32: Concrete Slab Design Summary 01 - Flexural And Shear Data, Part 2 of 3
Table 32: Concrete Slab Design Summary 01 - Flexural And Shear Data, Part 2 of 3
Strip SpanID Location FBotCombo FBotMomen FBotArea
t
kN-m mm2
CSA1 Span 1 Start UDCONU2 70.8612 372.592
CSA1 Span 1 Middle UDCONU2 0.0000 0.000
CSA1 Span 1 End UDCONU2 14.7629 76.985
CSA2 Span 1 Start UDCONU2 95.1356 498.857
CSA2 Span 1 Middle UDCONU2 0.0000 0.000
CSA2 Span 1 End UDCONU2 93.8933 492.294
CSA3 Span 1 Start UDCONU2 60.9574 318.754
CSA3 Span 1 Middle UDCONU2 0.0000 0.000
CSA3 Span 1 End UDCONU2 60.1976 314.761
CSA4 Span 1 Start UDCONU2 88.5801 464.235
CSA4 Span 1 Middle UDCONU2 0.0000 0.000
Table 32: Concrete Slab Design Summary 01 - Flexural And Shear Data, Part 2 of 3
Strip SpanID Location FBotCombo FBotMomen FBotArea
t
kN-m mm2
CSA4 Span 1 End UDCONU2 114.1821 599.663
CSA5 Span 1 Start UDCONU2 28.9226 150.850
CSA5 Span 1 Middle UDCONU2 0.0000 0.000
CSA5 Span 1 End UDCONU2 73.3460 383.920
CSA6 Span 1 Start UDCONU2 29.2804 153.015
CSA6 Span 1 Middle UDCONU2 0.0000 0.000
CSA6 Span 1 End UDCONU2 63.3461 332.718
CSB1 Span 1 Start UDCONU2 48.2532 259.155
CSB1 Span 1 Middle UDCONU2 17.4134 93.278
CSB1 Span 1 End UDCONU2 16.1072 86.272
CSB1 Span 2 Start UDCONU2 16.1072 86.272
CSB1 Span 2 Middle UDCONU2 32.4618 174.109
CSB1 Span 2 End UDCONU2 62.2619 334.792
CSB1 Span 3 Start UDCONU2 62.2619 334.792
CSB1 Span 3 Middle UDCONU2 15.4933 82.980
CSB1 Span 3 End UDCONU2 0.0000 0.000
CSB1 Span 4 Start UDCONU2 0.0000 0.000
CSB1 Span 4 Middle UDCONU2 2.1547 0.000
CSB1 Span 4 End UDCONU2 8.7464 0.000
CSB1 Span 5 Start UDCONU2 8.7464 0.000
CSB1 Span 5 Middle UDCONU2 0.4433 0.000
CSB1 Span 5 End UDCONU2 26.4608 141.851
Table 32: Concrete Slab Design Summary 01 - Flexural And Shear Data, Part 3 of 3
Table 32: Concrete Slab Design Summary 01 - Flexural And Shear Data, Part 3 of 3
Strip SpanID Location VCombo VForce VArea Status Layer
kN mm2/m
CSA1 Span 1 Start 0.000 0.000 OK A
CSA1 Span 1 Middle UDCONU2 48.169 0.000 OK A
CSA1 Span 1 End UDCONU2 27.046 0.000 OK A
CSA2 Span 1 Start 0.000 0.000 OK A
CSA2 Span 1 Middle UDCONU2 79.507 0.000 OK A
CSA2 Span 1 End UDCONU2 82.173 0.000 OK A
CSA3 Span 1 Start 0.000 0.000 OK A
CSA3 Span 1 Middle UDCONU2 50.737 0.000 OK A
CSA3 Span 1 End UDCONU2 135.362 0.000 OK A
CSA4 Span 1 Start 0.000 0.000 OK A
CSA4 Span 1 Middle UDCONU2 62.793 0.000 OK A
CSA4 Span 1 End UDCONU2 126.025 0.000 OK A
CSA5 Span 1 Start 0.000 0.000 OK A
CSA5 Span 1 Middle UDCONU2 68.251 0.000 OK A
CSA5 Span 1 End UDCONU2 150.607 0.000 OK A
CSA6 Span 1 Start UDCONU2 225.859 1830.689 OK A
CSA6 Span 1 Middle UDCONU2 47.750 0.000 OK A
CSA6 Span 1 End UDCONU2 229.116 1823.630 OK A
CSB1 Span 1 Start UDCONU2 23.547 0.000 OK B
CSB1 Span 1 Middle UDCONU2 85.558 0.000 OK B
CSB1 Span 1 End UDCONU2 14.756 0.000 OK B
CSB1 Span 2 Start UDCONU2 14.756 0.000 OK B
CSB1 Span 2 Middle UDCONU2 103.955 0.000 OK B
CSB1 Span 2 End UDCONU2 103.955 0.000 OK B
CSB1 Span 3 Start UDCONU2 103.955 0.000 OK B
Table 32: Concrete Slab Design Summary 01 - Flexural And Shear Data, Part 3 of 3
Strip SpanID Location VCombo VForce VArea Status Layer
kN mm2/m
CSB1 Span 3 Middle UDCONU2 168.782 0.000 OK B
CSB1 Span 3 End UDCONU2 50.907 0.000 OK B
CSB1 Span 4 Start UDCONU2 50.907 0.000 OK B
CSB1 Span 4 Middle UDCONU2 93.610 0.000 OK B
CSB1 Span 4 End UDCONU2 93.610 0.000 OK B
CSB1 Span 5 Start UDCONU2 93.610 0.000 OK B
CSB1 Span 5 Middle UDCONU2 58.592 0.000 OK B
CSB1 Span 5 End UDCONU2 103.833 0.000 OK B
IS 456-2000 Concrete Strip Design
Geometric Properties
Combination = 4
Point Label = 51
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 0 m
Global Y-Coordinate = 4.191 m
Geometric Properties
Combination = 4
Point Label = 52
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 8.001 m
Global Y-Coordinate = 4.191 m
Geometric Properties
Combination = 4
Point Label = 53
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 8.001 m
Global Y-Coordinate = 0 m
Geometric Properties
Combination = 3
Point Label = 57
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 2.921 m
Global Y-Coordinate = 0 m
Geometric Properties
Combination = 4
Point Label = 59
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 2.921 m
Global Y-Coordinate = 4.191 m
Geometric Properties
Combination = 3
Point Label = 61
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 6.0198 m
Global Y-Coordinate = 0 m
Geometric Properties
Combination = 4
Point Label = 63
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 6.0198 m
Global Y-Coordinate = 4.191 m