Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Installation manual
SAILOR 6390 Navtex Receiver
Installation manual
Copyright
© 2015 Thrane & Thrane A/S. All rights reserved.
Trademark acknowledgements
• SAILOR is a registered trademark of Thrane & Thrane A/S in the European Union, the United States of
America and other countries.
• Other product and company names mentioned in this manual may be trademarks or trade names of
their respective owners.
• This product contains Android™ software (a Google Inc. trademark).
GPL notification
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL.
The verbatim licenses can be found online at:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
You may obtain the complete corresponding source code from us for a period of three years after our last
shipment of this product, which will be no earlier than 2021, by sending a money order or check for DKK
50 to:
SW Technology/GPL Compliance,
Thrane & Thrane A/S,
Lundtoftegaardsvej 93D
2800 Lyngby
DENMARK
Please write "source for product SAILOR 6390 Navtex Receiver" in the memo line of your payment. This
offer is valid to anyone in receipt of this information.
ii 98-139768-C
Safety summary
Observe the following general safety precautions during all phases of operation, service and repair of this
equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual
violates safety standards of design, manufacture and intended use of the equipment. Thrane & Thrane
A/S assumes no liability for the customer's failure to comply with these requirements.
Warranty limitation
The SAILOR 6390 Navtex Receiver is not a user maintainable unit, and under no circumstances should
the unit be opened beyond the outer plastic cover, except by authorized personnel. Unauthorized
opening of the unit will invalidate the warranty.
98-139768-C iii
Preface
Record of Revisions
B The following sections have been edited: 2.1.2, 4.2.1, 26 February 2014 UFO
4.3.1, 4.4.4, 5.1.2
The following tables have been edited: 4-4, 4-7
The following figures have been added: 4-6, 5-2
The following figures have been edited: 4-3, 4-5, 4-11
iv 98-139768-C
Table of contents
Chapter 2 Introduction
2.1 Introduction to Navtex ...............................................................................................2-1
2.1.1 Overview ..................................................................................................................................2-1
2.1.2 Features ...................................................................................................................................2-2
2.1.3 Connector overview ..........................................................................................................2-2
2.2 Navtex message (example) .......................................................................................2-2
2.3 System components .......................................................................................................2-3
2.3.1 Use with the SAILOR 6004 Control panel ...............................................................2-3
2.3.2 Use as a stand-alone unit with an INS ......................................................................2-4
2.4 Part numbers ........................................................................................................................2-4
Chapter 3 Installation
3.1 Unpacking and initial inspection ..........................................................................3-1
3.1.1 Unpacking ...............................................................................................................................3-1
3.1.2 Initial inspection ..................................................................................................................3-1
3.2 Installation of the SAILOR 6390 Navtex Receiver ................................3-2
3.2.1 Dimensions .............................................................................................................................3-2
3.2.2 Drilling plan ............................................................................................................................3-3
3.2.3 Navtex antenna ....................................................................................................................3-3
3.2.4 Wiring ........................................................................................................................................3-4
3.2.5 Ethernet interfaces .............................................................................................................3-5
3.2.6 Recommended cables .......................................................................................................3-6
3.3 Installation of the SAILOR 6004 Control panel .......................................3-6
Chapter 4 Configuration
4.1 Start up .....................................................................................................................................4-1
4.1.1 To Power on and off ..........................................................................................................4-1
4.1.2 Dim and night mode ..........................................................................................................4-1
4.2 System and Navtex app installation .................................................................4-2
4.2.1 System app .............................................................................................................................4-2
4.2.2 Navtex app – daily use ......................................................................................................4-3
98-139768-C v
Table of contents
vi 98-139768-C
Table of contents
Glossary ..............................................................................................................................................................Glossary-1
98-139768-C vii
Table of contents
viii 98-139768-C
1111
Chapter 1
Document
Title and description
number
98-139768-C 1-1
Precautions
1.4 Precautions
Warnings, Cautions and Notes
Text marked with “Warning”, “Caution”, “Note” or “Important” show the following type of
data:
• Warning: A Warning is an operation or maintenance procedure that, if not obeyed, can
cause injury or death, or jeopardize the safety on board.
• Caution: A Caution is an operation or maintenance procedure that, if not obeyed, can
cause damage to the equipment.
• Note: A Note gives information to help the reader.
• Important: A text marked Important gives information that is important to the user,
e.g. to make the system work properly. This text does not concern damage on
equipment, travel safety nor personal safety.
General precautions
All personnel who operate equipment or do maintenance as specified in this manual must
know and follow the safety precautions. The warnings and cautions that follow apply to all
parts of this manual.
Introduction 2
Introduction
• Navtex message (example)
• System components
• Part numbers
2.1.1 Overview
The SAILOR 6390 Navtex Receiver receives Navtex messages on the international Navtex
frequencies 490 kHz, 518 kHz and 4,209.5 kHz. It can hold 2000 messages per frequency.
Messages are not affected by a power cycle. Untagged messages are cleared from the
message log after 661 hours, you can tag messages for later viewing. You can customise
which stations to receive messages from and which message types you want to receive.
The unit has an alarm relay which is only activated if a message of category D is received
(i.e. SAR, Mayday relay, Pirate attack etc.). The SAILOR 6390 Navtex Receiver is always on
when powered. With its LAN interface the transponder and the display can be separated,
giving access to the Navtex information available where it is needed.
The SAILOR 6390 Navtex Receiver is delivered as a black box receiver which can either be
connected to the SAILOR 6004 Control Panel, a 7" touch screen, or used as a standalone
unit for integration with an INS, supporting NMEA0183. A printer can be connected to the
receiver.
The SAILOR 6390 Navtex Receiver is approved according to GMDSS (EU Marine Equipment
Directive).
1. Default value.
98-139768-C 2-1
Navtex message (example)
2.1.2 Features
2000 messages per frequency, giving a total of 6000 messages
Printing via SAILOR 6004 Control Panel and 3rd party line printer over LAN
NO MESSAGE ON HAND
NNNN
Introduction
following list shows the Navtex message types
available. on page 2-12 for a list of all message
types.)
406391A-00500 SAILOR 6391 Navtex System (SAILOR 6004 Control Panel and
SAILOR 6390 Navtex Receiver)
Installation 3
Installation
3.1.1 Unpacking
The following items are included in the delivery of a SAILOR 6390 Navtex Receiver:
• SAILOR 6390 Navtex Receiver
• User manual SAILOR 6390 Navtex Receiver
• Installation guide SAILOR 6390 Navtex Receiver
• Cable RJ45 Cat5e STP, 5 m
• Mounting tool for terminal blocks
• Cable tie 5x200 mm (8 pieces)
• Fuse puller
• Fuse (1 A)
• Screw M4-x12 TORX 20 (5 pieces)
• Screw ST3.9x19 TORX (5 pieces)
After unpacking the system, inspect it thoroughly for hidden damage and loose
components or fittings. If the contents are incomplete, if there is mechanical damage or
defect, or if the system does not work properly, notify your dealer.
98-139768-C 3-1
Installation of the SAILOR 6390 Navtex Receiver
3.2.1 Dimensions
42.5 mm
190 mm
270 mm
4 x M4 or hole for
15.5 mm
self-tapping ø3.8 mm
124 mm 270 mm
Installation
190 mm
50.5 mm
12 mm 246 mm 12 mm
Minimum cable entry
150 mm
3.2.4 Wiring
PWR
TEST
ACC
AUX
PE 12-24 VDC
(internal fuse 3.15 A)
ALARM RELAY (normally closed) ON IN ON OUT
32 VDC @ 500 mA max. VBAT- 12-24 VDC
+ VBAT+ (internal fuse 1 A)
NMEA OUT (to INS) - Shield
+
NMEA IN (from INS) -
GND at talker end
NMEA IN (from eg. GPS) +-
GND at talker end
12-24 VDC
J9 J10
ALARM OUT NMEA IN-
ALARM OUT NMEA IN+ J11 J12
FUSE
RX AUDIO NMEA OUT- NMEA 2 IN+ VBAT+
GND NMEA OUT+ NMEA 2 IN- VBAT-
NMEA GPS R1112
/ON_IN
C73 C74 C63 C64
ON_OUT
R1110
R1111
GND
LABEL
Installation
J2
Figure 3-4: Spring-loaded terminals of the SAILOR 6390 Navtex Receiver (zoom)
3. Connect the SAILOR 6004 Control Panel via LAN to the SAILOR 6390 Navtex Receiver or
connect NMEA OUT (to INS) and NMEA IN (from INS).
4. Use the integrated cable relief to secure the cables with the provided cable ties.
5. Fasten the lid on the SAILOR 6390 Navtex Receiver with 4 screws (included in the
delivery).
1. Using a Control Panel as LPR print server (requires attaching a USB printer)
2. Using a third party LPR print server (requires IP address, port and queue name of that
server)
The figure and table below show the connector outline and pin assignments.
1 Tx+ White/Orange
2 Tx- Orange
3 Rx+ White/Green
4 Not connected Blue RJ-45 female
5 Not connected White/Blue
6 Rx- Green
7 Not connected White/Brown
8 Not connected Brown
Table 3-2: Pin allocation, LAN connector and cable
NMEA IN and NMEA OUT Shielded twisted pair (GPS / INS IN / INS OUT) 20 ma
(e.g. 0.15 mm2, AWG26)
Table 3-3: Recommended cables
a. At specified cable diameter.
Configuration 4
4.1 Start up
Configuration
As soon as DC power is provided the SAILOR 6390 Navtex Receiver is on.
To switch on the SAILOR 6004 Control Panel push the power button. Operate
the SAILOR 6004 Control Panel by tapping the touch screen. To switch off
the SAILOR 6004 Control Panel push and hold the power button for 2
seconds and follow the instructions on the screen.
If the Control Panel cannot switch off normally (e.g. due to a fault): Push and
hold for 12 seconds.
Note When the remote switch in the SAILOR 6004 Control Panel is wired and it is
switched on, you can only use the Power button to reboot the SAILOR 6004 Control
Panel, you cannot switch it off.
98-139768-C 4-1
System and Navtex app installation
Settings
The parameters in the section Settings are typically taken care of during installation.
Tap Settings to enter the section for network configuration, date and time setting, security
and reset. Tap the section you want to work with and explore the touch screen for each
setting. To change a setting you must enter the password for admin level (sailorsailor) and
tap OK.
Applications
Tap Applications to install, uninstall or update applications. This section has two tabs:
Available, showing the apps that are available to the SAILOR 6004 Control Panel on the
current network, and Installed, showing the apps already installed.
1. Tap Available to display the apps that are available to this SAILOR 6004 Control Panel.
2. Tap the app you want to install.
• Tap the app name, e.g. Navtex Version 1.0.
• Install to install this app on the SAILOR 6004 Control Panel.
Configuration
3. Enter the password for admin level (sailorsailor) and tap OK.
To manage an already installed app, do as follows:
1. Tap Installed to display the apps that are installed on this SAILOR 6004 Control Panel.
2. Tap the app you want to manage. For each app there are the following items:
• App name and version, e.g. Navtex Version 1.0.
• Update (if available, else grayed out) – tap here to update this app. Enter the
password for admin level and tap OK.
• Uninstall – tap here to uninstall this app from the SAILOR 6004 Control Panel.
• Display in bottom bar – tap here to show or hide the app’s icon in the bottom bar.
3. Enter the password for admin level (sailorsailor) and tap OK.
4. Select or deselect whether the app should be visible in the bottom bar of the SAILOR
6004 Control Panel.
Self Test
Tap Self Test to start the self test of the SAILOR 6004 Control Panel. For further details on
the self test see the installation manual of the SAILOR 6004 Control Panel.
About
Tap About to view the following:
• Legal with legal and copyright information, open source licences, etc.
• Version with software versions and serial number of the SAILOR 6004 Control Panel.
• Network with IP address and MAC address of the SAILOR 6004 Control Panel.
1. Make sure that DC power is provided for the SAILOR 6390 Navtex Receiver.
2. Connect a PC to the same network as the SAILOR 6390 Navtex Receiver (preferably a
direct connection to the Ethernet connector of the SAILOR 6390 Navtex Receiver).
3. Start the TMA (v. 1.04 or higher) and click on the SAILOR 6390 Navtex Receiver (TT-
6390 NAVTEX).
4. Click the icon Management and then Web interface. The Service Interface opens in a
browser window.
1. Switch on the SAILOR 6004 Control Panel and make sure that DC power is provided for
the SAILOR 6390 Navtex Receiver. Find the IP address of the Navtex Receiver, see the
manual of the SAILOR 6004 Control Panel (98-136644)
2. Connect a PC to the same network as the SAILOR 6390 Navtex Receiver.
3. Open an Internet browser (firefox or Chrome recommended) and enter the IP address of
the SAILOR 6390 Navtex Receiver, for example.:
HTTP://10.10.8.45
Configuration
Figure 4-5: Start screen of the Service Interface in an Internet browser
You can store the message database with all messages on a USB storage device. Do as
follows:
The image below shows an example of a file with stored messages, the output file is opened
in Microsoft Excel®.
1. Switch on the SAILOR 6004 Control Panel and make sure that DC power is provided for
the SAILOR 6390 Navtex Receiver
2. Tap System > Applications.
3. Tap in the top right corner and Device List.
4. Tap the unit, e.g. SAILOR 6390 Navtex Receiver.
5. Tap in the upper right corner and tap Service Interface.
The start screen of the Service Interface is shown.
Configuration
Figure 4-7: No connection to the SAILOR 6390 Navtex Receiver when using the Service Interface
2. If needed, enter a new System Function ID (Remote Device Name in the Navtex app on
the SAILOR 6004 Control Panel).
Note Change the System Function ID only if there is more than one SAILOR 6390
Navtex Receiver in the network.
The System Function ID is the identification of the SAILOR 6390 Navtex Receiver in the
network. It must consist of the letters CR followed directly by 4 digits. This must be the
same ID that has been set in the SAILOR 6004 Control Panel.
3. Select the antenna type: Low Z (Low impedance) for active antenna or High Z (High
impedance).
4. Automatic mode: You can enable automatic filtering of coast stations for each filter
category (Printing device, Storage and display and INS port) within the area of your own
position.
Select the filter (Printing device, Storage and display and INS port) you want to enable.
This can also be set up in the Navtex app in the SAILOR 6004 Control Panel.
5. Enter the receive radius in NM in the last field. Within this radius, relative to own
position, the SAILOR 6390 Navtex Receiver receives Navtex messages from all coast
stations.
Note Automatic mode requires a valid GPS input and that the coast station
table is maintained (e.g. new coast stations added if necessary).
If GPS fails for more than 10 minutes, a GPS alert and an Auto mode
alert will occur. As a consequence, Automatic mode will be disabled
stopping the coast station calculations. All stations are in the list again
and the user can filter out coast stations manually, see the user
manual.
You can also select Automatic mode in the Navtex app, see the user manual.
6. Click Submit to save the settings in the SAILOR 6390 Navtex Receiver.
INS Settings
Configuration
Figure 4-9: Service Interface: Interface Settings, INS Settings
Item Description
Name You can set the name according to your system requirements.
Baud Use the drop-down list to change the baud rate, if needed (default: 4800 baud).
Sensor Settings
The sensor port is connected to the GPS. It can be configured to decode different
categories/purposes:
• Sensor specific NMEA sentences
• Navtex specific NMEA sentences
• Alert specific NMEA sentences
• Proprietary NMEA sentences
Item Description
Name You can set the name according to your system requirements.
Baud Use the drop-down list to change the baud rate, if needed (default: 4800 baud).
Printer Settings
On this page you can enter the printer settings or disable the printer. You can also let the
system detect automatically a printer connected.
Configuration
Figure 4-11: Interface Settings, Printer Settings
Item Description
Static settings If you need a static IP you must enter the following:
– Static IP (IP address)
– Port number
– LPR Queue Name
See the documentation of the printer server.
Click Save to save the printer settings in the SAILOR 6390 Navtex Receiver.
Note Once the printer is configured in the SAILOR 6390 Navtex Receiver but not found
in the network, the SAILOR 6390 Navtex Receiver raises an alert.
1. Connect the printer to one of the two USB ports of the SAILOR 6004 Control Panel.
2. Switch on the SAILOR 6004 Control Panel and the printer attached.
3. Click Find printers in the section Automatic printer lookup. Then a list with serial
numbers of the available ThraneLINK print servers with attached printers is displayed.
4. Click the serial number of the desired print server, e.g. a serial number of a SAILOR 6004
Control Panel.
5. Click Save to save the printer settings in the SAILOR 6390 Navtex Receiver.
Ethernet Settings
The SAILOR 6390 Navtex Receiver and the SAILOR 6004 Control Panel communicate
through Ethernet. Other equipment can also communicate using the same Ethernet.
Therefore, it is necessary to configure an IP address and network ID for the SAILOR 6390
Navtex Receiver in the SAILOR 6004 Control Panel. I.e. the two devices must be paired.
The IP addresses of the SAILOR 6390 Navtex Receiver and the SAILOR 6004 Control Panel
are acquired automatically. There is also the possibility to set a static IP address. The IP
addresses are unique for each device connected to the Ethernet network.
There are two network IDs, one for the SAILOR 6390 Navtex Receiver and one for the
SAILOR 6004 Control Panel. The ID for Navtex receivers consists of two letters (CR or NR)
and four digits, e.g. CR0001. The ID must be unique for each device connected to the
Ethernet network.
Configuration
If needed you can set the SAILOR 6390 Navtex Receiver to have a static IP address.
Item Description
Click Submit to send the new settings to the SAILOR 6390 Navtex Receiver.
Item Description
Name You can name Multicast groups1 through 3 according to your system
requirements.
Item Description
Transmission Group Select which lightweight Ethernet transmission group to use for the
telegrams to use. Transmission groups must be unique for each port. For
Configuration
further information see Table B-1 on page B-1.
1. Select the frequency and the area from the drop-down box and click Search.
The current list of coast stations known to the SAILOR 6390 Navtex Receiver is
displayed.
2. Select the coast station by selecting the respective radio button and click Edit.
3. Make the changes and click Update to save the changes.
4. Add a coast station by filling in the fields, then click the Add. The new coast station will
now be known to the SAILOR 6390 Navtex Receiver.
Note A reset to factory default settings deletes all changes made to the coast station
list.
Configuration
Figure 4-15: Service Interface: System control
Factory Reset Click Factory Reset to reset the SAILOR 6390 Navtex Receiver to default
values. All user settings are deleted.
Backup You can save all settings of the Navtex Receiver in a file.
Click Backup to download a file with all user settings (navtexbackup.tar.gz).
4.4 Verification
The following sections provide a check list for verifying the installation and some tools for
verification:
• NMEA Trace tool
• Checking RF Reception Levels
• Installation Tests
Item OK
Apply power and check the three LEDs on the SAILOR 6390 Navtex Receiver
• Power LED is lit as soon as power is turned on (Note: The device will not
power on if terminal ON IN is left open)
• Test LED is lit after the Navtex receiver has successfully passed the self
test. Flashing indicates a self-test failure. This usually implies bad
antenna connection.
• Rx LED flashes when any of the three Navtex receivers are currently
receiving valid Navtex data
If the SAILOR 6004 Control Panel is attached, check that there are no alerts
in the bottom right corner of the display.
Table 4-7: Verifying the installation
You are now ready to receive Navtex messages. This of course depends on your current
physical location. Navtex messages are not necessarily received immediately. You can
check coast stations near you for a schedule when Navtex messages are sent.
1. Access the front page of the Service Interface, see To access the Service Interface on
page 4-4.
Note Do not log in to the Service Interface! The NMEA Trace tool is started and works
separately.
2. Click NMEA Trace.
Configuration
Figure 4-17: NMEA Trace
3. In the drop down list select whether you want to run an NMEA trace on:
In this window the current data to and from the port selected in the drop-down list are
displayed. At the same time you can monitor alarms related to the connected devices
and configure the connected devices in the display of the SAILOR 6004 Control Panel.
4. After ended tracing, you can download the NMEA trace log file to the PC’s default
download folder.
1. Access the log-in page of the Service Interface, see Access with an Internet browser on
page 4-5.
Note Do not log in to the Service Interface! The tool to measure RF reception levels
works separately.
2. Click RF Reception levels.
Configuration
Figure 4-20: Verification of RF reception levels
3. Click the button Get reception levels. RF levels are measured and sent to the service
interface.
4.201 MHz
490 kHz
518 kHz
1. Access the log-in page of the Service Interface, see Access with an Internet browser on
page 4-5.
Note Do not log in. The installation tests are run without being logged in.
3. Click the button Run Self Test to run a Self Test of the SAILOR 6390 Navtex Receiver.
4. Click the button Generate Test Message. The test message is displayed in the SAILOR
6004 Control Panel.
Note Make sure that the station Z for 490 kHz is selected for Display. (Tap on
Control Panel: Menu icon > Filters > Stations, Display).
5. Change audio source: The demodulated signal (1700 Hz +/-85 Hz) received on
518 kHz is always present for debug on connector J9. If a receiver is not performing as
expected, change the debug audio source to that receiver
(490 kHz/518 kHz/4209.5 kHz) and listen for e.g. a constant tone, indicating a spurious
on that receiver channel. The presence of a constant tone can then be compared to the
RF reception level measurements (see 4.4.3).
Note that changing the audio source is not saved to memory. After reboot the 518 kHz
channel is always selected.
J9
Rx audio
GND
• To toggle the Alarm Relay click On and Off to check the connected alarm system.
Note You must restart the Navtex Receiver after using the Installation Tests. Log in the
Service Interface and click Reboot or the button Logout.
5.1 Maintenance
Maintenance of the SAILOR 6390 Navtex Receiver can be reduced to a maintenance check at each
visit of the service staff. Inspect the unit for mechanical damages, salt deposits, corrosion and any
foreign material. Due to its robust construction and ruggedness the unit has a long lifetime. Anyway
it must carefully be checked at intervals not longer than 12 months – dependent on the current
working conditions.
2. Click the button View System Log to display the system log.
3. Click Download System Log. The systems log file is downloaded into the PC’s default
download folder.
98-139768-C 5-1
Maintenance
1. Download the TMA from the Cobham eSupport web site (Self-Service Center, SSC. You
find the SSC in the Service and Support section, 24-7 Service). Make sure to use version
1.04 or higher.
2. Make sure that your PC is on the same network segment as the SAILOR 6390 Navtex
Receiver.
3. Make sure that the SAILOR 6004 Control Panel is switched on.
4. Connect your PC to a free LAN interface of the SAILOR 6390 Navtex Receiver.
42.5 mm
5. Start the TMA on your PC. The SAILOR 6390 Navtex Receiver is automatically detected.
Click the icon for the SAILOR 6390 Navtex Receiver. The Software Download Status
must show Ready.
6. The icon Software update pulsates yellow when a new software version is detected
for the SAILOR 6390 Navtex Receiver.
The TMA searches all devices connected via USB for new software. You can add an
additional search path. To do so press the icon Options on the software update screen
and select Search for software. A dialog box is displayed and you can select a
directory.
7. To start the software update click the icon Software update and select Update. The
current and the new software version numbers are displayed.
You can also select a specific software version. To do so press the icon Options on the
software update screen and select Select software. A list of available software
versions is displayed. Select one and click the button Update.
1. Access the Navtex Receiver via the Service Interface, for details see Access with an
Internet browser on page 4-5.
2. Click Firmware Upgrade.
3. Click Browse. and find the software file (file extension: .tiif) and select it.
4. Click Upgrade.
1. Remove the cover of the SAILOR 6390 Navtex Receiver by loosening the 4 screws
marked in the figure below.
2. Remove the cables from the spring-loaded terminals and the connectors.
3. Remove the SAILOR 6390 Navtex Receiver by moving it upwards, away from the
mounting surface.
1. Track down why the fuse was blown and solve the problem, e.g. incorrect polarity at the DC
supply.
2. Remove the cover by loosening the 4 screws.
3. Take out the old fuse. Use the fuse puller.
4. Insert the new fuse. The fuse rating is 1 A.
Alert history
The alert history contains alerts of the last 24 hours (or maximum1000 entries).The alert
history is cleared when you switch off the SAILOR 6004 Control Panel. The alerts and
notifications are not saved. To display the alert history with alerts and notifications do as
follows
1. Tap the flashing icon in the lower right corner to display the list with alerts and
notifications.
2. Tap the check box next to ACK to acknowledge the alert.
006 General Failure (W) Power cycle the unit. If this does
not help, contact your suplier.
If the connection between the SAILOR 6390 Navtex Receiver and the SAILOR 6004 Control
Panel is lost, the SAILOR 6004 Control Panel shows an error “Connection lost”. Make sure
that no one is connected to the SAILOR 6390 Navtex Receiver using the Service Interface.
1. 246060 indicates unknown time (invalid time stamp), e.g. if there is no or invalid GPS input.
1. From any list of messages (Unread, Tagged or All), tap the menu icon and Settings.
2. Tap the menu icon again, then RX Self Test.
1. Wrap the defective unit in heavy paper or plastic. Attach a tag indicating the type of
service required, return address, part number and full serial number.
2. Use a strong shipping container, e.g. a double walled carton.
3. Protect the front- and rear panel with cardboard and insert a layer of shock-absorbing
material between all surfaces of the equipment and the sides of the container.
4. Seal the shipping container securely.
5. Mark the shipping container FRAGILE to ensure careful handling.
Failure to do so may invalidate the warranty.
Technical specifications
Technical specifications A
98-139768-C A-1
NMEA PCB in SAILOR 6390 Navtex Receiver
NMEA sentences B
NMEA sentences
All sentences are defined according to NMEA 0183 version 4.10 and IEC 61162-1 Ed. 4.0.
1. When used with a SAILOR 6004 Control Panel the network IP traffic load may increase to a
level where IEC 61162-450 compliance cannot be guaranteed.
98-139768-C B-1
NMEA sentences used
B.2.1 Overview
You find detailed description of the following sentences in this appendix:
• ACK - Acknowledge alarm (input)
NMEA sentences
• ACN - Alert command (input)
• ALC - Cyclic alert list (output)
• ALF - Alert sentence (output)
• ALR - Set alarm state
• CRQ - Query sentence
• NRM - NAVTEX receiver mask (input/output)
• NRX - NAVTEX received message (output)
• RMC - Recommended minimum specific GNSS data (input)
• ZDA - Time and Date (input/output)
NMEA sentences
1 ALR Sentence Id Used
2 hhmmss.ss Time of alarm condition change, UTC Used
3 xxx Unique alarm number (identifier) at alarm source Used
4 A Alarm’s acknowledge state, A=Acknowledged, Used
V=Unacknowledged
5 A Alarm condition, A=Threshold exceeded, V=Not Used
exceeded
6 c--c*hh Alarm description text Used
Table B-7: NMEA sentence: ALR
NMEA sentences
3 a Status (A or V) Used
4 llll.ll Latitude Used
5 a Latitude N/S Used
6 yyyyy.yy Longitude Used
7 a Longitude E/W Used
8 x.x Speed over ground, knots Not Used
9 x.x Course over ground, degrees true Not Used
10 xxxxxx Date: ddmmyy Used
11 x.x Magnetic variation, degrees Not Used
12 a Magnetic variation, E/W Not Used
13 a Mode indicator Not Used
14 a Navigational status Not Used
Table B-11: NMEA sentence: RMC
D
DC Direct Current
DHCP Dynamic Host Configuration Protocol. A protocol for assigning dynamic IP addresses to
devices on a network. With dynamic addressing, a device can have a different IP address
every time it connects to the network.
DNS Domain Name System. A system translating server names (URLs) to server addresses.
Glossary
GMDSS Global Maritime Distress and Safety System. The system is intended to perform the
following functions: alerting (including position determination of the unit in distress),
search and rescue coordination, locating (homing), maritime safety information
broadcasts, general communication, and bridge-to-bridge communication.
I
INS Integrated Navigation System
L
LAN Local Area Network. A computer network covering a small physical area, like a home,
office, school or airport. The defining characteristics of LANs, in contrast to wide-area
networks (WANs), include their usually higher data-transfer rates, smaller geographic area,
and lack of a need for leased telecommunication lines.
N
NAVDAT High Speed NAVtex DATa sent out on 500 kHz. Not yet part of mandatory Navtex
reception, but mentioned in ITU-R M.2010 and ITU-R M.2201.
98-139768-C Glossary-1
Glossary
NMEA National Marine Electronics Association (standard). A combined electrical and data
specification for communication between marine electronic devices such as echo
sounder, sonars, anemometer (wind speed and direction), gyrocompass, autopilot, GPS
receivers and many other types of instruments. It has been defined by, and is controlled
by, the U.S.-based National Marine Electronics Association.
R
RSTP Rapid Spanning Tree Protocol is typically able to respond quickly to changes in network
topology or in case of a physical link failure. RSTP provides significantly faster spanning
tree convergence after a topology change.
Rx Receive
T
TMA Thrane Management Application
Tx Transmit (Ethernet)
Glossary-2 98-139768-C
4444
Index
Index 4
A configuration
load, 4-17
alarm, 5-5 save, 4-17
relay, toggle, 4-22 connection lost, 4-4, 4-7
alarms connector
INS, 5-9 LAN, 3-5
Navtex, 5-8 Navtex antenna, 3-4
printer, 5-8 overview, 2-2
alerts
history, 5-7
icons, 5-5
antenna
D
connector, 3-4 debug
placing, 3-4 audio source, 4-22
select type, 4-8 spurious, 4-22
app default settings
display in bottom bar, 4-3 reset to, 4-17
Index
install, 4-3 delete messages, 4-17
uninstall, 4-3 delivery
update, 4-3 items included, 3-1
applications, 4-2 DHCP, 4-13
audio source, 4-22 dimming function, 4-1
change, 4-22 display
auto range, 4-8 brightness, 4-1
Automatic mode, 4-8
E
B
Ethernet, 3-5
backup connector, 3-5
configuration, 4-17 settings, 4-12
bottom bar transmission group, 4-15
display app, 4-3
brightness, 4-1
buzzer, 2-3
F
factory default
C coast station list, 4-16
factory reset, 4-17
cable specifications, 3-6 filtering coast stations, 4-8
clear messages, 4-17 fuse
coast station size, 3-1
add new, 4-16
filtering, 4-8
list, reset, 4-16
update, 4-16
G
compass safe distance, -iii, 3-2 GMDSS installations, 3-5
98-139768-C Index-1
Index
H Navtex message
example, 2-3
history Navtex Receiver
alerts, 5-7 specifications, A-1
use stand alone, 2-4
use with Control panel, 2-3
I night mode, 2-3, 4-1
NMEA sentences, B-2
install app, 4-2 NMEA tracer, 4-19
installation, 3-1
invalid time stamp
alarm, 5-9
IP address
O
Control Panel, 4-3 open source licences, 4-3
DHCP or static, 4-13
Navtex Receiver, 4-4, 4-5
printer, 4-11
P
part numbers, 2-4
L password, 4-3, 4-7
placing
LAN antenna, 3-4
connector, 3-5 print server, 4-12
license printer
software, -ii 3rd party, setup, 4-12
LWE disable, 4-12
multicast addresses, B-1 IP address, 4-11
LWE ID, 4-12 ThraneLINK compatible, setup, 4-12
Control Panel, 4-14 printer settings, 4-11
Navtex Receiver, 4-14
R
M
reboot
MAC address power cycle, 4-17
Control Panel, 4-3 Remote Device Name, 4-7
messages reset, 4-17
clear, 4-17 coast stations, 4-16
multicast addresses, B-1 RF exposure, -iii
RF reception level, 4-21
RF reception levels, 4-21
N RSTP, 4-13
RX self test
NAVDAT, 2-2 Navtex Receiver, 5-11
Navtex antenna, 3-4
placing, 3-4
select type, 4-8
Navtex areas
S
add coast station, 4-16 self test, 4-3, 4-22
Navtex frequencies, 2-1 Control Panel, 4-3
Navtex Receiver, 5-11
Index-2 98-139768-C
98-139768-C
www.cobham.com/satcom
4444
Index
Index
uninstall, 4-3 NMEA Trace, 4-19
software license, -ii RF reception levels, 4-21
software update
service interface, 5-3
TMA, 5-2 W
via Control Panel, 4-3
software version warranty, -iii, 5-13
TMA, 4-4
specifications, A-1
Navtex Receiver, A-1
Static IP, 4-13
System Function ID, 4-7
T
Talker ID White List
INS, 4-9
LWE, 4-14
Sensor, 4-10
technical data, A-1
test message, 4-22
generate, 4-22
time
invalid, 5-9
TMA
add search path, 5-2
software update, 5-2
software version, 5-2
specific software, 5-3
version, 4-4
98-139768-C Index-3