Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
(a) Static
(b) Dynamic
(c) Any of a & b
(a) Impulse
(b) Reaction
(c) Both
6. Function of nozzle in an impulse turbine is …………..
(a) To convert pressure into velocity
(b) To convert velocity into pressure
(c) To increase both velocity & pressure
7. In case of sleeve type journal bearing the bearing……….
(a) Touches the shaft
(b) Does not touch the shaft
8. The tendency of air or gas to move outward from the center of rotating
impellers is called ………………. tendency.
(a) Centrifugal
(b) Rotary
(c) Centripetal
(d) Linear
9. When the gas is at the tips of centrifugal compressor impeller blades, it is
at …… velocity.
(a) Minimum
(b) Maximum
(c) Medium
(d) Zero
10. The diffuser coverts the velocity of the gas to increase gas ………………
(a) Temperature
(b) Pressure
(c) Volume
(d) Energy
11. A centrifugal compressor by doing work on a gas imparts both ………. &
………. to the gas.
12. At any given RPM, the work done by the compressor on each pound of
gas handled is ……………….
(a) Nearly constant
(b) Variable
(c) Increasing
(d) Decreasing
(a) Decrease
(b) Increase
(c) Remained constant
(d) None of above
(a) increase
(b) decrease
(c) vary
(a) Highest
(b) Lowest
(c) Critical
20. Misalignment usually appears at…………in a spectrum
(a) 1 X
(b) 2 X
(c) 5 X
(d) 10X
22. Packing is chosen on the basis of liquid being pumped and its ………….
(a) Pressure
(b) Temperature
(c) Density
23. Smallest size of a plain journal bearing may be …………..
(a) 1 inch
(b) ½ inch
(c) ¼ inch
24. Which of the following will offer better resistance to unexpected load and
shock conditions?
(a) Antifriction bearing
(b) Plain journal bearing
25. In a full journal bearing or bushing the strength comes from ………
(a) bearing housing wall thickness
(b) bushing wall thickness
26. In boundary lubrication (in case of journal bearing) what is happening?
(a) There is no metal to metal contact
(b) There is some metal to metal contact
29. For high speed machine what kind of lubrication will be preferred?
(c) Lube oil
(d) Grease
(e) Doesn’t matter
30. Which one of the following will not require re-lubrication?
(a) Sealed bearing
(b) Shielded bearings
36. In centrifugal pump ribs are provided on the back of impeller for…..
(a) Radial balancing
(b) Axial balancing
37. Write down at least one cause for the following problems in a steam
turbine?
(a) Excessive vibration
(b) Excessive coupling wear
(c) Turbine fails to start
(d) Turbine does not come up to speed
(e) Excessive steam consumption
(f) Erratic speed control
(g) Over speed trip not functioning properly.
(h) Turbine does not cool down after stoppage
(i)Water in lubricating oil
38. The speed-sensing drive which indicates turbine speed and makes
correction is called…………..
(a) Tachometer
(b) Speed sensor
(c) Governor
(a) Horizontally
(b) Vertically
(c)
Diameter of inlet lines as compared to discharge line in compressors is ……….
(a) Smaller
(b) Larger
(c) Equal
42. In a pump, the close fit between the stationary wear ring and the rotating
wear ring ………..the amount of high pressure liquid going back into the
suction.
(a) Increase
(b) Decrease
43. An unbalance impeller may cause a …………..vibration.
(a) Axial
(b) Radial
47. The balancing drum is attached to the shaft at the ………..end of the
compressor.
(a) Suction
(b) Discharge
Q-10. (x – 6) (x – 4) = ________________. A x2 + 10 x + 24
B x2 – 10 x - 24
C x2 + 10 x – 24
D x2 – 10 x + 24
Q-11. THE TWO NUMBERS, WHO’S SUM IS –13 AND PRODUCT A 2, 15
– 30 ARE. B 2, -15
C -3, 10
D 3, -10
Q-17. ONE AND ONLY ONE LINE CAN PASS THROUGH A ONE POINT
B TWO POINTS
C THREE POINTS
D FOUR POINTS
Q-19. THE TWO ARCS OF TWO DIFFERENT CIRCLES ARE A THE CIRCLES ARE CONGRUENT.
CONGRUENT IF _______________________. B CORRESPONDING CENTRAL
ANGLES ARE CONGRUENT.
C BOTH A AND B ARE SATISFIED.
D NONE OF THESE.
Q-23. WHICH ONE OF THESE AGENTS DOES NOT TAKE PART A COMBUSTABLE GAS
IN COMBUSTION B STEAM
C AIR
D SOURCE OF HEAT