Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Rotary Process
Valve
Flow Control
Company Profile Series 30,000 metal seated,
Offset 1
Achieved by placing
the shaft behind the
plane of the sealing
surface. The purpose
of this offset is to
have a continuous
seat path. Seated
➂
Design Standards
Quality Assurance: ISO 9001
Offset 3
Environmental
Achieved by inclining the seat and seal cone centerline in Management System: ISO 14001
respect of the pipe and valve centerline. This third offset
Compliance with: Pressure Equipment Directive
completely eliminates rubbing. Any chances of associated PED 97/23/EC, category III.
wear and leakage between the seat and disc-mounted seal Cat. IV mod. H1 available on
ring during travel are non-existent. request.
Vanessa optimizes the contact angle between the seat and Design: ASME B16.34, API 609, DIN
seal for enhanced performance. Most gate valves provide a 3840, EN 593
contact angle of between 3 and 6 degrees. Such designs Face-to-Face: ISO 5752, EN 558, ASME
create a locking taper that can cause dangerously high seat- B16.10, API 609
ing or unseating torques. Flange Drilling: ASME B16.5, ASME B16.47,
ISO 7005, DIN 2501, EN 1092
Vanessa’s contact angle is above the locking taper range and
its geometry eliminates the possibility of jamming, ensuring Testing: API 598, API 6D, ISO 5208
3 the forces necessary to seat or unseat the valve do not sub- Fire Test: API 607, 4th Edition
stantially vary over the service life of the valve. Marking: MSS SP 25, EN 19
Valve Configuration and options
-20 to 100 285 275 740 720 1,480 1,440 2,220 2,160 -29 to 8
200 260 240 675 620 1,350 1,240 2.205 1,860 93
300 230 215 655 560 1,315 1,120 1,970 1,680 149
400 200 195 635 515 1,270 1,030 1,900 1,540 204
500 170 170 600 480 1,200 955 1,795 1,435 260
600 140 140 550 450 1,095 905 1,640 1,355 316
650 125 125 535 445 1,075 890 1,610 1,330 343
700 110 110 535 430 1,065 865 1,600 1,295 371
750 95 95 505 425 1,010 845 1,510 1,270 399
800 80 80 410 415 825 830 1,235 1,245 427
850 65 65 270 405 535 810 805 1,215 454
900 50 50 170 395 345 790 515 1,180 482
950 35 35 105 385 205 775 310 1,160 510
1000 20 20 50 365 105 725 155 1,090 538
1050 – 20 (1) – 360 – 720 – 1,080 566
1100 – 20 (1) – 325 – 645 – 965 593
1150 – 20 (1) – 275 – 550 – 825 621
1200 – 20 (1) – 205 – 410 – 620 649
7165 3968
Weight (Lbs)
6614 3637
6063 3307
5511 2976
4960 2645
4409 2315
3858
1984
3307
1653
2756
1323
2204
1653 992
1102 661
551 331
0 0
10” 12” 14” 16” 18” 20” 24” 30” 32” 36” 3” 4” 6” 8” 10” 12” 14” 16” 18” 20” 24”
Size Size
Notes: 4. FCI 70-2 and IEC 534-4 leak rates depend on the test differential
pressure.
1. Vanessa performs seat tightness test on each manufactured valve
with water and air in both directions, covering all the requirements of 5. Class IV leak rates depend on the “valve rated capacity”, and there-
API 598, API 6D and ISO 5208. fore they are function of the valve trim rating.
2. According to API 598 standard, 1 ml of water is equivalent to 16 6. Leak rates have been extrapolated using the relationship between
5 “drops”. seat diameter and leakage factors suggested in Note 2 of Table IV of
IEC 534-4.
3. According to FCI 70-2 and IEC 534-4 standards, 1 ml of air is equiva-
lent to 6.67 “bubbles”. 7. Class VI leak rates depend on the Nominal Diameter, therefore they
are independent of the pressure classes.
Cryogenic Test
Resilient METAL Seat No Teflon® or Kalrez® Helium Leakage Comparison
Leakage rate in ml/min X ND inch at -196°C
The Vanessa Series 30,000 valve, Cryogenic Version
provides for unmatched tightness even when compared to
soft seated designs. 160
The tightness capability is achieved as a direct result of the
resiliency of the metal seal ring. This seal ring resiliency is 140
150 150
generated by the radial compression of the seal as torque is
applied to the valve shaft. 120
Disc
Bracket
Seal
Bushing
Thrust Bearing
7
Materials of Construction (ASTM Standard) Basic Configuration
Item Note Description Body in Carbon Steel Body in Stainless Steel
1a Body ASTM A216 WCB ASTM A351 Gr.CF8M
1b Body Seat Stellite® Gr.21 Weld Overlay Stellite® Gr.21 Weld Overlay
2a ❑
Disc ASTM A216 WCB Nickel Plated ASTM A351 Gr.CF8M
or ASTM A105 Nickel Plated or ASTM A182 type F316
2b Retainer Flange ASTM A516 Nickel Plated AISI 316
2c Screw ISO 3506 A4 (AISI 316) ISO 3506 A4 (AISI 316)
3a● Seal Ring UNS S31803 (Duplex) + Graphite UNS S31803 (Duplex) + Graphite
3b● Disc Spiral Wound Gasket AISI 316 + Graphite AISI 316 + Graphite
4a Shaft ASTM A182 F6a ASTM A479 UNS S20910 (Nitronic® 50)
4b Disc Key AISI 410 UNS S20910
4c Pin AISI 410 UNS S20910
4d Pin Retainer AISI 316 AISI 316
5a● Packing Graphite Graphite
5b Spacer AISI 316 AISI 316
5c Packing Bushing AISI 316 AISI 316
5d Stud Nut ISO 3506 A2 (AISI 304) ISO 3506 A2 (AISI 304)
5e Stud Bolts ISO 3506 A2 (AISI 304) ISO 3506 A2 (AISI 304)
6a Bottom Flange ASTM A516 ASTM A240 Type 316
6b Screw ISO 3506 A2 (AISI 304) ISO 3506 A2 (AISI 304)
6c● Bottom Spiral
AISI 316 + Graphite AISI 316 + Graphite
Wound Gasket
7a Thrust Bearing AISI 316 or AISI 410 UNS S20910
7b Thrust Bearing Washer AISI 316 AISI 316
7c Key AISI 316 AISI 316
7d Screw ISO 3506 A4 (AISI 316) ISO 3506 A4 (AISI 316)
7e Unloosening Washer AISI 410 AISI 316
8a Bearing AISI 304 Hard Faced AISI 316 Hard Faced
9a Bracket Carbon Steel Carbon Steel
9b Screw Alloy Steel Alloy Steel
Notes
❑: The selection between cast or forged material depends on valve size.
●: Suggested spare parts.
The Vanessa Series 30,000 can be manufactured as standard in the following materials:
WCB, CF8M, LCB, WC6, CF3M, Aluminum Bronze, Duplex, 250 SMO.
Additionally, the Vanessa Series 30,000 can be manufactured also in the following materials: Monel®, Incoloy®,
Hastelloy®, Alloy Steel WC6-WC9, Superduplex, Inconel®, Alloy 20, C5, Titanium.
Contents may change without notice.
High
Pressure
Side
Face-to-face
High
Pressure
Side
Face-to-face
Double Flanged - Face-to-face ISO 5752 Table 1 Col. 13 - Body Drilling ASME B16.47 Series A Cl. 150 - Trim B
Size Valve Dimensions Gear Type Gear Dimensions Weight
mm inch A B E L FT C I X ØV Valve Total
700 28” 42.5 20.62 32.5 11.5 2.81 MAGA 1000C-90 39.62 7.87 19.62 17.75 1690 2032
750 30” 44 24.25 34 12.53 2.94 MAGA 1000C-90 41.12 7.87 19.62 17.75 2182 2524
800 32” 45 25.25 35 12.53 3.19 MAGA 1000C-90 42.12 7.87 19.62 17.75 2568 2910
900 36” 51.37 26.5 39.62 13 3.53 MAGA 2000C-110 48.5 10.37 26.37 27.5 3295 3880
1000 40” 53.37 29.12 41.5 16.16 3.56 MAGA 2000C-120 50.37 10.37 26.37 27.5 4486 5070
1050 42” 54.5 29.75 42.75 16.16 3.81 MAGA 2000C-120 51.62 10.37 26.37 27.5 4750 5335
1200 48” 65 34.12 49.87 18.5 4.25 MAGA 14KR 57.5 7.87 38 32.25 6713 8134
1350 54” 69.5 38.75 54.37 20.87 4.75 MAGA 14KR 61.87 7.87 38 32.25 9479 10901
1500 60” 74.5 44.62 59 23.62 5.19 MAGA 18KR 66.62 9 41.62 2.25 12654 14407
Double Flanged - Face-to-face ISO 5752 Table 1 Col. 13 - Body Drilling ASME B16.5 Cl.300 - Trim C
Size Valve Dimensions Gear Type Gear Dimensions Weight
mm inch A B E L FT C I X ØV Valve Total
80 3” 13.37 4.87 10.24 4.5 1.12 OV 10-18 11.75 2.25 6.5 5 48 63
100 4” 14.62 5.5 11.42 5 1.25 OV 10-18 12.87 2.25 6.5 5 72 88
150 6” 17.37 7.5 13.78 5.5 1.44 OV 50-28 15.37 2.62 8.62 11.75 134 158
200 8” 20.37 9.25 16.34 6 1.62 OV 100-35 18.25 3.37 13.37 19.75 189 218
250 10” 21.87 10.75 17.91 6.5 1.87 OV 100-35 19.87 3.37 13.37 19.75 220 249
300 12” 24.25 12.25 19.29 7 2 OV 200-45 21.5 4.62 14.62 23.5 385 451
350 14” 26.37 13.25 21.46 7.5 2.12 OV 200-50 23.62 4.62 14 27.5 626 692
400 16” 28.75 15.37 22.64 8.5 2.25 OV 400ER-55 25 5.12 16.5 11.75 749 850
450 18” 32.12 16.62 25.98 8.75 2.37 OV 400ER-65 28.37 5.12 21.87 19.75 1073 1177
500 20” 33.62 18.12 27.56 9 2.5 OV 400ER-65 29.87 5.12 21.87 19.75 1166 1269
600 24” 39.12 20.87 30.91 10.5 2.75 MAGA 400C-75 34.75 3.87 13.75 17.75 1838 1992
Double Flanged - Face-to-face ISO 5752 Table 1 Col. 14 - Body Drilling ASME B16.5 Cl.600 - Trim D
Size Valve Dimensions Gear Type Gear Dimensions Weight
mm inch A B E L FT C I X ØV Valve Total
80 3” 12.37 5.37 9.25 7.09 1.25 OV 10-20 10.75 2.25 6.5 6 70 85
100 4” 15.25 7.25 11.75 7.47 1.5 OV 50-30 13.25 2.62 8.62 11.75 145 169
150 6” 18 9.37 14 8.28 1.87 OV 100-40 15.87 3.37 13.37 19.75 266 295
200 8" 20.87 10.37 16 9.06 2.19 OV 200-45 18.12 4.62 14.62 23.5 436 502
250 10” 25.25 12.87 19.12 9.84 2.5 OV 400ER-55 21.5 5.12 16.5 11.75 656 758
300 12” 29.5 14.37 21.12 10.62 2.62 MAGA 400C-60 25 3.87 13.75 17.75 833 987
350 14” 32.25 15.37 24 11.41 2.75 MAGA 400C-70 27.87 3.87 13.75 17.75 981 1135
400 16” 36.75 17.37 26.75 12.22 3 MAGA 1000S-75 33.87 7.87 19.62 17.75 1477 1818
450 18” 36.87 18.12 26.87 13 3.25 MAGA 1000C-90 34 7.87 19.62 17.75 1653 1995
500 20” 43.12 20.75 31.25 3.78 3.5 MAGA 2000S-100 40.25 10.37 26.37 27.5 2204 2788
600 24” 46.62 24.5 34.87 15.34 4 MAGA 2000C-120 43.75 10.37 26.37 27.5 3196 3780
Double Flanged - Face-to-face ISO 5752 Table 1 Col. 8 - Body Drilling ASME B16.5 Cl.900 - Trim E
Size Valve Dimensions Gear Type Gear Dimensions Weight
mm inch A B E L FT C I X ØV Valve Total
150 6” 18 9.37 14 8.84 2.19 OV 100-40 15.87 3.37 13.37 19.75 368 396
200 8” 24.5 11.5 18.37 10.81 2.5 OV 400ER-55 20.75 5.12 16.5 11.75 654 756
250 10” 28.75 13.62 20.5 12.78 2.75 MAGA 400C-60 24.25 3.87 13.75 17.75 848 1003
300 12” 38.87 18.87 28.87 14.75 3.12 MAGA 1000S-70 36 7.87 19.62 17.75 1296 1638
350 14” 36.87 18 26.87 16.72 3.37 MAGA 1000C-90 34 7.87 19.62 17.75 1752 2094
400 16” 38.75 19.37 28.75 18.69 3.5 MAGA 1000C-90 35.87 7.87 19.62 17.75 2707 3048
450 18” 42.12 20.12 30.37 19.69 4 MAGA 2000C-120 39.25 10.37 26.37 27.5 3179 3763 10
500 20” 46.12 23.25 34.25 22.62 4.25 MAGA 2000C-120 43.12 10.37 26.37 27.5 4250 4834
600 24” 55.75 26.5 40.5 26.56 5.5 MAGA 14KR 48.12 7.87 38 32.25 6267 7689
Series 30,000 Metal Seated, Zero Leakage Rotary Process Valves
High
Pressure
Side
Face-to-face
High
Pressure
Side
Face-to-face
High
Pressure
Side
Face-to-face
Double Flanged Body Style (Face-to-Face ASME B16.10), Lug and Wafer installed on Piping
11
Double Flanged - Face-to-Face ASME B16.10 Table 1 Double Flanged - Face-to-Face ASME B16.10 Table 2
Col.7 Body Drilling ASME B16.5 Cl.150 - Trim B Col.10 Body Drilling ASME B16.5 Cl.300 - Trim C
Size Valve Dimensions Weight Size Valve Dimensions Weight
mm inch L N FT Valve Total mm inch L N FT Valve Total
80 3” 8 4.87 0.94 50 66 80 3” 11.12 7.75 1.12 57 72
100 4” 9 3.5 0.94 66 81 100 4” 12 3.75 1.25 88 103
150 6” 10.5 4 1 79 94 150 6” 15.88 4.25 1.44 174 198
200 8" 11.5 4.12 1.12 154 178 200 8” 16.5 5 1.62 253 282
250 10” 13 5.12 1.19 216 240 250 10” 18 5.5 1.87 299 328
300 12” 14 6 1.25 306 335 300 12” 19.75 6 2 511 577
350 14” 15 6.87 1.37 410 438 350 14” 30 22.5 2.12 875 941
400 16” 16 7.62 1.44 504 570 400 16” 33 24.37 2.25 1060 1161
450 18” 17 8.5 1.56 593 659 450 18” 36 26.12 2.37 1558 1662
500 20” 18 9 1.69 782 848
600 24” 20 9 1.87 1111 1212
Lugged - Face-to-Face API 609 CL.150 Lugged - Face-to-Face API 609 Cl. 300
Body Drilling ASME B16.5 Cl.150 - Trim B Body Drilling ASME B16.5 Cl. 300 - Trim C
Size Valve Dimensions Weight Size Valve Dimensions Weight
mm inch L N Valve Total mm inch L N Valve Total
80 3” 1.88 0.81 28 44 80 3” 1.88 0.81 39 55
100 4” 2.12 0.94 37 52 100 4” 2.12 0.94 48 63
150 6” 2.25 1 50 66 150 6” 2.31 1 90 114
200 8" 2.5 1.12 79 103 200 8" 2.88 1.25 123 152
250 10” 2.81 1.25 108 132 250 10” 3.25 1.44 169 198
300 12” 3.19 1.5 182 211 300 12” 3.62 1.56 262 328
350 14” 3.62 1.75 257 286 350 14” 4.62 2.37 559 626
400 16” 4 1.94 352 418 400 16” 5.25 2.56 661 762
450 18” 4.5 2.19 427 493 450 18” 5.88 2.87 1003 1106
500 20” 5 2.5 595 661 500 20” 6.25 2.81 1100 1203
600 24” 6.06 3.06 853 954 600 24” 7.12 3.25 1737 1891
Wafer - Face-to-Face API 609 Cl.150 Wafer - Face-to-Face API 609 Cl. 300
Body Drilling ASME B16.5 Cl.150 - Trim B Body Drilling ASME B16.5 Cl. 300 - Trim C
Size Valve Dimensions Weight Size Valve Dimensions Weight
mm inch L N Valve Total mm inch L N Valve Total
80 3” 1.88 0.81 30 46
80 3” 1.88 0.81 30 46
100 4” 2.12 0.94 33 48
100 4” 2.12 0.94 33 48
150 6” 2.25 1 44 59
150 6” 2.31 1 63 88
200 8" 2.5 1.12 74 99
200 8" 2.88 1.25 110 138
250 10” 2.81 1.25 99 123
250 10” 3.25 1.44 165 194
300 12” 3.19 1.5 160 189
300 12” 3.62 1.56 240 306
350 14” 3.62 1.75 213 242
350 14” 4.62 2.37 361 427
400 16” 4 1.94 271 337
400 16” 5.25 2.56 502 604
450 18” 4.5 2.19 361 427
450 18” 5.88 2.87 628 731
500 20” 5 2.5 485 551
500 20” 6.25 2.81 756 859
600 24” 6.06 3.06 714 815
600 24” 7.12 3.25 1130 1285
Notes:
1. For the dimensions A, B, E, and for Gear Selection and dimensions, please refer to the relevant figures in the previous Double
Flanged tables.
2. Suggested orientation is with the valve shaft horizontal or inclined from vertical.
3. For service above 392°F [200°C], valve body should be insulated to limit body-to-trim differential temperature to 212°F [100°C].
4. All dimensions are in inches and weight is in pounds.
5. Please consult Vanessa for other sizes.
12
Vanessa has manufacturing experience for much larger sizes than those indicated (for example: 112”/CI.150,
56”/CI.300, 48”/CI.600, 36”/CI.900). Please consult factory for further information.
Cryogenic Configuration
Materials selection
Item Description Material
Bracket
1a Body ASTM A 351 CF8M
1b Body Seat Stellite® gr. 21 Weld Overlay
Bonnet
2a❑ Disc ASTM A 351 CF8M or
ASTM A 182 gr. F316
2b Retainer Flange AISI 316
2c Screw ISO 3506 A4 (AISI 316) Disc
3a● Seal Ring UNS S20910 or UNS S21800
3b● Disc Spiral Wound Gasket AISI 316 + Graphite
4a Shaft ASTM A479 Type XM19
4b Disc Key UNS S20910
4c Pin UNS S20910
4d Pin Retainer AISI 316
5a● Packing Graphite
5b Spacer AISI 316 Seal
5c Packing Bushing AISI 316
Shaft
5d Stud Nut ISO 3506 A2 (AISI 304)
5e Stud Bolts ISO 3506 A2 (AISI 304)
6a❑ Bottom Flange ASTM A 351 CF8M or
ASTM A 240 gr. F316
6b Screw ISO 3506 A2 (AISI 304)
6c● Bottom Spiral Wound Gasket AISI 316 + Graphite
7a Thrust Bearing UNS S20910
7b Thrust Bearing Washer AISI 316
7c Key AISI 316
7d Screw ISO 3506 A4 (AISI 316)
7e Unloosening Washer AISI 316
8a Bearing Aisi 304 Hard Faced
9a Bracket Carbon Steel
9b Screw Alloy Steel
10a Bonnet ASTM A351 gr. CF8M or
Packing Packing (optional) Bottom
AISI 316 Fabricated
10b Bearing AISI 304 Hard Faced
10c Screw ISO 3506 A2 (AISI 304)
10d Bonnet Spiral Wound Gasket AISI 316 + Graphite
Materials selection
Item Description Body in CF8M
1a Body ASTM A 351 CF8M
1b Body Seat Stellite® gr. 21 Weld Overlay
2a❑ Disc ASTM A 351 CF8M or
ASTM A 182 gr. F316
2b Retainer Flange AISI 316
2c Screw ASTM A 453 gr. 660
3a● Seal Ring UNS S20910 or UNS S21800
3b● Disc Spiral Wound Gasket AISI 316 + Graphite
Bracket
4a Shaft ASTM A479 Type XM19
4b Disc Key UNS S20910
Disc
4c Pin UNS S20910
4d Pin Retainer AISI 316
5a● Packing Graphite
5b Spacer AISI 316
5c Packing Bushing AISI 316
5d Stud Nut ISO 3506 A2 (AISI 304)
5e Stud Bolts ISO 3506 A2 (AISI 304)
Seal 6a❑ Bottom Flange ASTM A 351 CF8M or
ASTM A 240 gr. F316
Bonnet Shaft
6b Screw ASTM A 453 gr. 660
6c Bottom Spiral Wound Gasket AISI 316 + Graphite
7a Thrust Bearing UNS S20910
7b Thrust Bearing Washer Stellite® gr. 21
7c Key AISI 316
7d Screw ASTM A 453 gr. 660
7e Unloosening Washer AISI 316
8a Bearing AISI 316 Hard Faced
Packing Packing (optional) Bottom 9a Bracket Carbon Steel
9b Screw Alloy Steel
10a Bonnet ASTM A 351 CF8M
10b Bearing AISI 304 Hard Faced
10c Screw ASTM A 453 gr. 660
10d Bonnet Spiral Wound Gasket AISI 316 + Graphite
Extended bonnet
Extended bonnet - dimensions and weight
Size Trim B Trim C Trim D Trim E
in. mm H Bonnet Weight H Bonnet Weight H Bonnet Weight H Bonnet Weight
3 80 5.91 11.0 5.91 11.0 5.91 13.2 - -
4 100 5.91 13.2 5.91 13.2 5.91 15.4 - -
6 150 5.91 17.6 5.91 22.0 5.91 28.7 5.91 35.3
8 200 5.91 24.3 5.91 37.5 5.91 50.7 5.91 66.1
10 250 5.91 33.1 5.91 44.1 9.84 72.8 9.84 92.6
12 300 5.91 50.7 5.91 55.1 9.84 92.6 9.84 121.3
14 350 5.91 55.1 5.91 68.3 9.84 119.0 9.84 211.6
Notes
16 400 5.91 70.5 5.91 108.0 9.84 176.4 9.84 264.6
1. Trim A: Dp max. 150 psi (10 bar). 18 450 9.84 90.4 9.84 119.0 9.84 277.8 9.84 330.7
Trim B: Dp max. 362 psi (25 bar).
Trim C: Dp max. 725 psi (50 bar). 20 500 9.84 103.6 9.84 154.3 13.78 370.4 13.78 396.8
Trim D: Dp max. 1595 psi (110 bar). 24 600 9.84 141.1 9.84 242.5 13.78 458.6 13.78 485.0
Trim E: Dp max. 2320 psi (160 bar). 28 700 11.81 191.8 11.81 297.6 13.78 507.1 - -
2. Dimensions are in inches and weight is in 30 750 11.81 260.1 11.81 330.7 13.78 551.2 - -
pounds.
32 800 11.81 308.6 11.81 396.8 - - - -
3. Other materials are available on request.
36 900 11.81 352.7 11.81 463.0 13.78 683.4 - -
❑ The selection between cast and forged 40 1000 11.81 396.8 11.81 507.1 - - - -
material depends on valve size. 42 1050 11.81 463.0 11.81 551.2 - - - - 14
● Suggested Spare Parts. 48 1200 11.81 507.1 11.81 617.3 - - - -
Steam Jacketed Configuration
Materials selection
Item Description Material
1a Body ASTM A216 WCB
1b Body Seat Stellite® gr. 21 Weld Overlay
1m Flanged Fitting ASTM A105
1n Body Jacket ASTM A515 gr. 60
2a❑ Disc ASTM A216 WCB or
ASTM A105 Disc
2b Retainer Flange ASTM A516
2c Screw ISO 3506 A4 (AISI 316)
3a● Laminated Seal Ring UNS S31803 (Duplex) + Graphite
3b● Disc Spiral Wound AISI 316 + Graphite
Gasket Bracket
4a Shaft ASTM A182 F6a
4b Disc Key AISI 410
4c Pin AISI 410
Seal
4d Pin Retainer AISI 316
5a● Packing Graphite
5b Spacer AISI 316
5c Packing Bushing AISI 316
5d Stud Nut ISO 3506 A2 (AISI 304)
5e Stud Bolts ISO 3506 A2 (AISI 304)
5h Lantern Ring AISI 316
5m Plug AISI 316 Shaft Seal (optional)
6a Bottom Flange ASTM A516
6b Screw ISO 3506 A2 (AISI 304)
6c● Bottom Spiral Wound AISI 316 + Graphite
Gasket
7a Thrust Bearing AISI 316 or AISI 410
7b Thrust Bearing Washer AISI 316
7c Key AISI 316
7d Screw ISO 3506 A4 (AISI 316)
7e Unloosening Washer AISI 410
Packing Bottom Bushing
8a Bearing AISI 304 Hard Faced
8b Bearing Protector Reinforced Graphite
9a Bracket Carbon Steel
9b Screw Alloy Steel
Notes
Heating connections Auxiliary condense drainage 1. For ND up to 12” (ANSI drilling), the heating connection flange dim.
is 1/2” Cl. 300 ANSI B16.5, RF 125÷250 µinch. For DN up to 300
mm (DIN and ISO 7005 drilling), the heating connection flange dim.
is DN 15 PN 40, RF 12,5÷25 µm.
Inlet
Inlet 2. For ND from 14” and larger (ANSI drilling), the heating connection
flange dim. is 3/4” Cl. 300 ANSI B16.5, RF 125÷250 µinch. For DN
from 350 mm and larger (DIN and ISO 7005 drilling), the heating
connection flange dim. is DN 20 PN 40, RF 12,5÷25 µm.
3. For ND up to 12”, the auxiliary condense drainage (P) is 3/8” NPT.
For ND from 14” and larger, the auxiliary condense drainage (P) is
1/2” NPT.
15
Superior Manufacturing Expertise
16 16
Industries and Applications
Vanessa valves have an impressive track record of Vanessa has extensive experience of supplying valves
service in both isolation and control applications in all for a wide variety of fluids including:
process industries including:
• Hydrocarbons
• Oil and Gas Processing
• Steam (Saturated and Superheated)
• Offshore Platforms
• Geothermal Steam
• Refineries
• Hydrogen
• Hydrocarbons Storage and Transportation
• Oxygen
• Liquid Natural Gas (LNG) Storage
• Cryogenic Fluids
and Transportation
• Hot Gases
• Chemical and Petrochemicals Plants
• Sulphur (Tail Gas)
• Power Generation
• Chemical Solvents
• District Heating
• Chlorinated Solvents
• Pulp and Paper
• Flare Gas
• Steel Mills
• Sugar Mills
• Desalination Plants
• Water Treatment and Distribution
17
HP Butterfly Valves
Ball Valves
Gate Valves
Vanessa Valves
✦ Zero Leakage Standard
Vanessa’s Series 30,000 valves are bi-directionally tested to rigid zero
leakage standard of both API 598 and API 6D.
✦ ✦ ✦ Quarter-Turn Operation
Fugitive emissions are greatly reduced. Automation is simplified.
Compactness imposes less stress on pipe.
✦ ✦ All-Metal Construction
Temperature limits inherent to soft-seated valves do not affect the
all-metal construction of Vanessa Series 30,00 valves.
✦ ✦ ✦ Bi-Directional
The Vanessa Series 30,000 valve provides bi-directional, zero
leakage shutoff.
✦ ✦ Inherently Firesafe
All-metal construction in combination with zero leakage performance equals
inherently firesafe. The Series 30,000 is zero leakage before, during, and
QTF after a fire test.
✦ Non-Rubbing Design
The Series 30,000’s unique triple offset design eliminates all rubbing
and resulting wear during the entire 90 degrees of travel.
✦ Double-Flange Body
Standard double-flange end connections (ISO 5752) offer greater ease of
installation and maintenance in a compact configuration.
✦ ✦ ✦ ✦ Cryogenic to -400°F
✦ ✦ ✦ High Temperature to 1500°F
Metal-seated performance with far better shutoff than soft seated valves in
temperature affected applications.
✦ ✦ ✦ Quick Operation 18
Vanessa’s quarter-turn valves operate as quick as 0.15 seconds.
www.tycoflowcontrol.com Flow Control
Tyco Flow Control (TFC) provides the information herein in good faith but makes no representation as to its comprehensiveness or accuracy. This data sheet is intended only as a guide to TFC products and serv-
ices. Individuals using this data sheet must exercise their independent judgment in evaluating product selection and determining product appropriateness for their particular purpose and system requirements.
TFC MAKES NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE WITH RESPECT TO THE INFORMATION SET FORTH HEREIN OR THE PRODUCT(S) TO WHICH THE INFORMATION REFERS. ACCORDINGLY, TFC WILL NOT BE RESPONSIBLE FOR DAMAGES
(OF ANY KIND OR NATURE, INCLUDING INCIDENTAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES) RESULTING FROM THE USE OF OR RELIANCE UPON THIS INFORMATION. Patents and Patents
Pending in the U.S. and foreign countries. Tyco reserves the right to change product designs and specifications without notice.