Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Tail Pulley - 4 in. dia. with 1 3/16 in. dia. shaft, crowned. Motor - 1/2 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed,
Snub Roller - 2 1/2 in. dia. galvanized with grease packed fan cooled.
ball bearings (adjustable). Electrical Controls - Available as option.
Return Rollers - 1.9 in. dia. galvanized with grease packed Frame Capacity - Maximum load per linear foot with legs on 10 ft.
ball bearings. centers = 100 lbs. Not to exceed capacities in chart on next page.
5 1/2"
1.9" DIA.
RETURN
33 7/8" TO 38 1/8" ROLLER
TOP OF BELT 2 1/2" DIA.
SNUB ROLLER
ROLLER REMOVED
WHEN TAKE-UP CLOSE
TO END
12"
8" DIA. DRIVE FINGER GUARD
FLOW
PULLEY Horizontal Slider Bed Belt Conveyor Model Number:
_____
B H S _E -_ -_0 - _ - _ _ - _0 -_ -_
10 1/16" Slider Bed (4) 4" dia. Drive Pulley
Belt Conveyor (8) 8" dia. Drive Pulley
(E) End Drive
(C) Center Drive Horsepower
(S) Shaft Mount (1/3 HP to 2 HP)
33 7/8" TO 38 1/8"
TOP OF BELT Belt Width Angle of Incline (0°)
Optional Equipment:
Belt - PVC-120 white, PVC-120 ruff-top, nitrile, 3-ply solid woven Ceiling Hangers - 5/8 in. dia. x 10 ft. long threaded rod with
cotton. Other types available. mounting hardware. Other lengths available. See page 161.
Belt Lacing - Recessed, hidden, vulcanized endless. Other types Other Drive Types - Shaft mount, over-top, side mount chain
available. driven to allow lower top of belt.
Conveying Speed - Constant and variable speeds available other Tail Pulley - 6 in. dia. with 1 3/16 in. dia. shaft, crowned.
than standard 60 FPM. Motors - Single phase, explosion proof, etc. Available through
Center Drive/Take-Up - Provides additional belt take-up and is 2 HP.
suitable for reversible applications. See page 161. Electrical Controls - Start/stop push-button station, reverse
Center Take-Up - Provides additional belt take-up. Allows tail pulley drum switch, one direction and reversible magnetic starters.
location closer to end for better product transition. Nose Roller Ends - Ideal for small product transfer. See photo,
Belt Conveyors
Fixed Angle Guard Rails - 1 1/2 in. x 2 in. or 1 1/2 in. x 6 in. formed pages 147 and 155.
12 ga. galvanized angle. Other heights available. V-Guided Construction - Required if length-to-belt width ratio is
Adjustable Guard Rails - 1 5/8 in. x 1 in. formed channel. Adjusts less than 2.5:1. 5 1/2 in. x 1 1/2 in. x 12 ga. galvanized frame.
horizontally from edge of belt to 10 inches wider than belt. Available See photo, page 149.
on conveyors with center drives or shaft mounted end drives only. Inclines - Available upon request. See page 160.
Floor Supports - Heights available up to 84 in. top of leg.
Standard Specifications:
Belt - Black PVC-120 with clipper lacing. Return Rollers - 1.9 in. dia. with grease packed ball bearings.
Belt Widths - 6 in. to 48 in. in full one inch increments. Take-up - Provides belt take-up at tail pulleys to allow for future
Bed - 10 ga. formed steel slider bed pans welded in 5 1/2 in. belt stretch.
deep x 10 ga. painted steel channel frames. Standard 5 ft. and Bearings - Sealed, pre-lubricated, self aligning ball bearings on drive
10 ft. long welded sections, with welded-in end couplers. and tail pulleys.
Floor Supports - 3 in. structural channel legs with 4 in. Conveying Speed - Constant 60 FPM.
adjustment. Available up to 89 in. top of belt. One support at every Speed Reduction - Sealed worm gear “C” face flanged speed
bed joint and at ends of conveyor. reducer.
Drive Pulley - 4 in. dia. with 1 3/16 in. dia. shaft, 8 in. dia. with Motor - 1/2 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan
Belt Conveyors
1 7/16 in. dia. shaft or 1 11/16 in. dia. shaft, crowned and fully cooled.
lagged.
Electrical Controls - Available as option.
Tail Pulley - 4 in. dia. with 1 3/16 in. dia. shaft, 6 in. dia. with
Frame Capacity - Maximum load per linear foot with legs on 10 ft.
1 7/16 in. dia. shaft, crowned.
centers = 300 lbs. Not to exceed capacities in chart on next page.
Snub Rollers - 2 1/2 in. dia. with grease packed ball bearings
(adjustable).
2 3/4" 5' DRIVE SECTION INTERMEDIATE SECTIONS 5' TO 10' TAKE-UP SECTION
2 1/4"
2 3/4" - 8 3/4"**
BED ACTS AS FINGER GUARD FLOW
4" DIA. DRIVE PULLEY 4" DIA. TAKE-UP PULLEY
5 1/2"
1.9" DIA.
10 GA. FORMED
89" MAX. RETURN ROLLER
STEEL SLIDER PAN
TOP OF BELT 2 1/2" DIA.
SNUB ROLLER
3" STRUCTURAL
CHANNEL LEGS
1" 5" DRIVE SECTION INTERMEDIATE SECTIONS 5' TO 10' TAKE-UP SECTION
4 1/2"
2 3/4" - 8 3/4"**
BED ACTS AS FINGER GUARD
FLOW
8" DIA. DRIVE PULLEY 6" DIA. TAKE-UP PULLEY
9 1/2" 7 1/2"
89" MAX.
TOP OF BELT
Center Take-Up - Provides additional belt take-up. Allows tail Nose Roller Ends - Ideal for small product transfer. See photo
pulley location closer to end for better product transition. above and on page 155.
Fixed Angle Guard Rails - 1 1/2 in. x 2 in. or 1 1/2 in. x 6 in. V-Guided Construction - Required if length-to-belt width ratio
formed 10 ga. angle. Other heights available. Channel types is less than 2.5:1. See photo, page 149.
available. Inclines - Available upon request. See page 160.
Floor Supports - 4 in. structural channel legs. Structural Channel Construction - Available upon request.
Model HDSB
■ Welded Construction
■ 7 1/2 in. x 1 1/2 in. x 7 ga. Frame
■ Belt Widths Up To 60 in.
CONVEYOR WEIGHT (LBS.)
■ Reversible (With Center Drive) BELT WIDTH (BW)**
OAL
18" 24" 30" 36" 42" 48" 54" 60"
5’ 712 - -* - -* - -* - -* - -* - -* - -*
10’ 8 in. dia. drive, 6 in. dia. tail
910 1009 1107 1205 - -* - -* - -* - -*
15’ 1107 1242 1393 1506 1639 1774 2054 - -*
Standard Specifications:
Belt - Black PVC-120 with clipper lacing. Return Rollers - 1.9 in. dia. or 2 1/2 in. dia. with grease packed ball
Belt Widths - 12 in. to 60 in. in full one inch increments. bearings.
Bed - 7 ga. formed steel slider bed pans welded in 7 1/2 in. deep Take-up - Provides belt take-up at tail pulleys to allow for future belt
x 7 ga. painted steel channel frames. Standard 5 ft. and 10 ft. stretch.
long welded sections, with welded-in end couplers. Bearings - Sealed, pre-lubricated, self aligning ball bearings on
Floor Supports - 4 in. structural channel legs with 4 in. drive and tail pulleys.
adjustment. Available up to 89 in. top of belt. One support at Conveying Speed - Constant 30 FPM.
every bed joint and at ends of conveyor. Speed Reduction - Sealed worm gear “C” face flanged speed
Drive Pulley - 8 in. dia. with 1 15/16 in. dia. shaft, 12 in. dia. with reducer.
Belt Conveyors
1 15/16 in. dia. shaft or 2 3/16 in. dia. shaft, crowned and fully Motor - 2 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan
lagged. cooled.
Tail Pulley - 6 in. dia. with 1 11/16 in. dia. shaft, 8 in. dia. with Electrical Controls - Available as option.
1 11/16 in. dia. shaft, crowned.
Frame Capacity - Maximum load per linear foot with legs on 10 ft.
Snub Rollers - 3 1/2 in. dia. with grease packed ball bearings centers = 620 lbs. Not to exceed capacities in chart on next page.
(adjustable).
7 1/2"
9 1/2"
4" STRUCTURAL
CHANNEL LEGS
13 1/2" 9 1/2"
89" MAX.
TOP OF BELT
formed 7 ga. angle. Other heights available. Channel types available. less than 2.5:1. See photo, above.
Floor Supports - 5 in. structural channel legs. Inclines - Available upon request. See page 160.
Ceiling Hangers - 1/4 in. formed angle mounted to underside of Structural Channel Construction - Available upon request.
conveyor. Hanging hardware not included. See page 161.
Drive Pulley - For 3 HP motor, 16 in. dia. with 2 7/16 in. dia. shaft; for
5 HP motor, 16 in. dia. with 2 15/16 in. dia. shaft, crowned and fully lagged.
Standard Specifications:
Belt - Black PVC-150 with clipper lacing. Return Rollers - 1.9 in. dia. or 2 1/2 in. dia. with grease packed ball
Belt Widths - 24 in. to 72 in. in full one inch increments. bearings.
Bed - 1/4 in. formed steel slider bed pans welded in 12 in. deep Take-up - Provides belt take-up at tail pulleys to allow for future
1/4 in. painted steel channel frames. Standard 5 ft. and 10 ft. long belt stretch.
welded sections, with welded-in end couplers. Bearings - Sealed, pre-lubricated, self-aligning ball bearings on drive
Floor Supports - 5 in. structural channel legs with 4 in. and tail pulleys.
adjustment. Available up to 89 in. top of belt. One support at Conveying Speed - Constant 30 FPM.
every bed joint and at ends of conveyor. Speed Reduction - Sealed worm gear “C” face flanged speed
Drive Pulley - 8 in. dia. with 1 15/16 in. dia. shaft, 12 in. dia. reducer.
Belt Conveyors
with 1 15/16 in. dia. shaft or 2 3/16 in. dia. shaft, 16 in. dia. with Motor - 2 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan
2 15/16 in. dia. shaft, crowned and fully lagged. cooled.
Tail Pulley - 6 in. dia. with 1 11/16 in. dia. shaft, 8 in. dia. with Electrical Controls - Available as option.
1 11/16 in. dia. shaft, crowned.
Frame Capacity - Maximum load per linear foot with legs on 10 ft.
Snub Rollers - 3 1/2 in. dia. with grease packed ball bearings centers = 1280 lbs. Not to exceed capacities in chart on next page.
(adjustable).
3" 5' DRIVE SECTION INTERMEDIATE SECTIONS 5' TO 10' TAKE-UP SECTION
12"
6 1/2" BED ACTS AS FINGER GUARD 8 1/2" BED ACTS AS FINGER GUARD
6 1/2"
17 1/2"
Optional Equipment:
Belt - PVC-150 white, PVC-200 black, 2-ply 150 rubber roughtop, Other Drive Types - Shaft mount, over-top, side mount chain
nitrile. Other types available. driven to allow lower top of belt.
Belt Lacing - Recessed, hidden, vulcanized endless. Other types Motors - Single phase, explosion proof, etc. Available through
available. 7 1/2 HP.
Conveying Speed - Constant and variable speeds available other Electrical Controls - Start/stop push-button station, reverse
than standard 30 FPM. drum switch, one direction and reversible magnetic starters.
Center Drive/Take-Up - Provides additional belt take-up and is Nose Roller Ends - Ideal for small product transfer. See photo,
suitable for reversible applications. pages 147 and 155.
Center Take-Up - Provides additional belt take-up. Allows tail pulley V-Guided Construction - Required if length-to-belt width ratio is
Belt Conveyors
location closer to end for better product transition. less than 2.5:1. See photo, page 149.
Fixed Angle Guard Rails - 1 1/2 in. x 2 in. or 1 1/2 in. x 6 in. formed Inclines - Available upon request. See page 160.
7 ga. angle. Other heights available. Channel types available. Structural Channel Construction - Available upon request.
Floor Supports - 6 in. structural channel legs.
Ceiling Hangers - 3/8 in. formed angle mounted to underside of
conveyor. Hanging hardware not included. See page 161.
NOTE: A short belt segment laced on both ends, commonly called a “dutchman”, is SPACING ROLLER WEIGHT ADDER PER FOOT (LBS.)
provided with conveyors over 47 ft. OAL. This allows future belt stretch with 3" (+) 5.0 (+) 6.2 (+) 6.9 (+) 7.5 (+) 8.7 (+) 10.5 (+) 12.3
standard end take-up. If short segment is not desired, a center drive/take-up is
9" (-) 1.7 (-) 2.1 (-) 2.3 (-) 2.5 (-) 2.9 (-) 3.5 (-) 4.1
required.
12" (-) 2.5 (-) 3.1 (-) 3.4 (-) 3.7 (-) 4.3 (-) 5.3 (-) 6.2
* Other widths are available
Standard Specifications:
Belt - Black PVC-120 with clipper lacing. Return Rollers - 1.9 in. dia. galvanized with grease packed ball
Belt Widths - 12 in., 16 in., 18 in., 20 in., 24 in., 30 in. and 36 in. bearings.
Bed - Roller bed with 1.9 in. dia. x 16 ga. galvanized rollers Take-Up - Provides belt take-up at tail pulley to allow for future belt
spaced every 6 inches. Mounted in 5 1/2 in. deep x 12 ga. stretch.
galvanized steel channel frames. Standard 5 ft. and 10 ft. long Bearings - Sealed, pre-lubricated, self-aligning ball bearings on drive
bolt-together sections with bolt-on end couplers. and tail pulleys.
Floor Supports - Adjustable 32 1/8 in. to 38 1/8 in. top of belt with Conveying Speed - Constant 60 FPM.
4 in. drive. Adjustment is 32 5/8 in. to 38 1/8 in. with an 8 in. drive. Speed Reduction - Sealed worm gear “C” face flanged speed
One support at every bed joint and at ends of conveyor. reducer with No. 50 chain to drive pulley.
Cross Bracing - Rods with turn buckles supplied on every other Motor - 1/3 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan
section for conveyors 30 ft. and longer. Allows frame to be cooled.
Belt Conveyors
5 1/2"
1.9" DIA.
32 1/8" TO 38 1/8" RETURN
TOP OF BELT ROLLER 2 1/2" DIA.
SNUB ROLLER
ROLLER REMOVED
WHEN TAKE-UP CLOSE
TO END
Optional Equipment:
Belt - PVC-120 white, PVC-120 ruff-top, nitrile, white butyl, 3-ply solid Floor Supports - Heights available up to 84 in. top of leg.
woven cotton. Other types available. Ceiling Hangers - 5/8 in. dia. x 10 ft. long threaded rod with
Belt Lacing - Recessed, hidden, vulcanized endless. Other types mounting hardware. Other lengths available. See page 161.
available. Other Drive Types - Shaft mount, over-top, side mount chain
Conveying Speed - Constant and variable speeds available other driven to allow lower top of belt.
than standard 60 FPM. Tail Pulley - 6 in. dia. with 1 3/16 in. dia. shaft, crowned.
Center Drive/Take-Up - Provides additional belt take-up and is Motors - Single phase, explosion proof, etc. Available through
suitable for reversible applications. See page 161. 2 HP.
Center Take-Up - Provides additional belt take-up. Allows tail pulley Electrical Controls - Start/stop push-button station, reverse
location closer to end for better product transition. drum switch, one direction and reversible magnetic starters.
Roller Centers - Bed rollers spaced on 3 in., 9 in. or 12 in. centers. Bed Rollers - 1.9 in. dia. x .145 in. wall.
Belt Conveyors
Fixed Angle Guard Rails - 1 1/2 in. x 2 in. or 1 1/2 in. x 6 in. formed Nose Roller Ends - Ideal for small product transfer. See photo,
12 ga. galvanized angle. Other heights available. page 147 and 155.
Adjustable Guard Rails - 1 5/8 in. x 1 in. formed channel. Adjusts Inclines - Available upon request. See page 160.
horizontally from edge of belt to 10 inches wider than belt. Available
on conveyors with center or shaft mounted drives only.
lagged.
Frame Capacity - Maximum load per linear foot with legs on 10 ft.
Tail Pulley - 4 in. dia. with 1 3/16 in. dia. shaft, 6 in. dia. with
centers = 300 lbs. Not to exceed capacities in chart on next page.
1 7/16 in. dia. shaft, crowned.
Snub Rollers - 2 1/2 in. dia. with grease packed ball bearings
(adjustable).
2 3/4" 5' DRIVE SECTION INTERMEDIATE SECTIONS 5' TO 10' TAKE-UP SECTION
2 1/4"
2 3/4" - 8 3/4"**
FINGER GUARD FLOW
4" DIA. DRIVE PULLEY 4" DIA. TAKE-UP PULLEY
5 1/2"
1.9" DIA.
1.9" DIA. RETURN ROLLER
89" MAX
TOP OF BELT BED ROLLER 2 1/2" DIA.
SNUB ROLLER
3" STRUCTURAL
CHANNEL LEGS
1" 5' DRIVE SECTION INTERMEDIATE SECTIONS 5' TO 10' TAKE-UP SECTION
4 1/2"
3 3/4" - 9 3/4"**
FINGER GUARD
FLOW 6" DIA. TAKE-UP PULLEY
8" DIA. DRIVE PULLEY
9 1/2" 7 1/2"
89" MAX
TOP OF BELT
Roller Centers - Bed rollers spaced on 3 in., 9 in. or 12 in. centers. less than 2.5:1. Special split bed to allow v-guide clearance
through bed rollers.
Fixed Angle Guard Rails - 1 1/2 in. x 2 in. or 1 1/2 in. x 6 in. formed
10 ga. angle. Other heights available. Channel types available. Inclines - Available upon request. See page 160.
Floor Supports - 4 in. structural channel legs. Structural Channel Construction - Available upon request.
Ceiling Hangers - 1/4 in. formed angle mounted to underside of
conveyor. Hanging hardware not included. See page 161.
Standard Specifications:
Belt - Black PVC-120 with clipper lacing. Return Rollers - 1.9 in. dia. or 2 1/2 in. dia. with grease packed ball
Belt Widths - 18 in. to 60 in. in full one inch increments. bearings.
Bed - Roller bed with 2 1/2 in. dia. x 11 ga. rollers with 11/16 hex Take-up - Provides belt take-up at tail pulleys to allow for future belt
shafts spaced every 6 inches. Mounted in 7 1/2 in. deep stretch.
x 7 ga. painted steel channel frames. Standard 5 ft. and 10 ft. Bearings - Sealed, pre-lubricated, self aligning ball bearings on
long welded sections, with welded-in end couplers. drive and tail pulleys.
Floor Supports - 4 in. structural channel legs with 4 in. Conveying Speed - Constant 30 FPM.
adjustment. Available up to 89 in. top of belt. One support at Speed Reduction - Sealed worm gear “C” face flanged speed
every bed joint and at ends of conveyor. reducer.
Drive Pulley - 8 in. dia. with 1 15/16 in. dia. shaft, 12 in. dia. Motor - 2 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan
Belt Conveyors
with 1 15/16 in. dia. shaft or 2 3/16 in. dia. shaft, crowned and cooled.
fully lagged.
Electrical Controls - Available as option.
Tail Pulley - 6 in. dia. with 1 11/16 in. dia. shaft, 8 in. dia.
Frame Capacity - Maximum load per linear foot with legs on
with 1 11/16 in. dia. shaft, crowned.
10 ft. centers = 620 lbs. Not to exceed capacities in chart on
Snub Rollers - 3 1/2 in. dia. with grease packed ball bearings next page.
(adjustable).
9 1/2" 7 1/2"
9 1/2"
13 1/2"
89" MAX
TOP OF BELT
Standard Specifications:
Belt - Black PVC-150 with clipper lacing. Return Rollers - 1.9 in. dia. or 2 1/2 in. dia. with grease packed ball
Belt Widths - 24 in. to 72 in. in full one inch increments. bearings.
Bed - Roller bed with 2 1/2 in. dia. x 11 ga. rollers with 11/16 hex Take-up - Provides belt take-up at tail pulleys to allow for future belt
shafts spaced every 6 inches. Mounted in 12 in. deep x 1/4 in. stretch.
painted steel channel frames. Standard 5 ft. and 10 ft. long Bearings - Sealed, pre-lubricated, self aligning ball bearings on drive
welded sections, with welded-in end couplers. and tail pulleys.
Floor Supports - 5 in. structural channel legs with 4 in. Conveying Speed - Constant 30 FPM.
adjustment. Available up to 89 in. top of belt. One support at Speed Reduction - Sealed worm gear “C” face flanged speed
every bed joint and at ends of conveyor. reducer.
Drive Pulley - 8 in. dia. with 1 15/16 in. dia. shaft, 12 in. dia. Motor - 2 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan
Belt Conveyors
with 1 15/16 in. dia. shaft or 2 3/16 in. dia. shaft, 16 in. dia. with cooled.
2 15/16 in. dia. shaft, crowned and fully lagged.
Electrical Controls - Available as option.
Tail Pulley - 6 in. dia. with 1 11/16 in. dia. shaft, 8 in. dia. with
Frame Capacity - Maximum load per linear foot with legs on 10 ft.
1 11/16 in. dia. shaft, crowned.
centers = 1280 lbs. Not to exceed capacities in chart on next page.
Snub Rollers - 3 1/2 in. dia. with grease packed ball bearings
(adjustable).
3" 5' DRIVE SECTION INTERMEDIATE SECTIONS 5' TO 10' TAKE-UP SECTION
12"
13 1/2" 17 1/2"
Fixed Angle Guard Rails - 1 1/2 in. x 2 in. or 1 1/2 in. x 6 in. formed less than 2.5:1. Special split bed to allow v-guide clearance
7 ga. angle. Other heights available. Channel types available. through bed rollers.
Floor Supports - 6 in. structural channel legs. Inclines - Available upon request. See page 160.
Ceiling Hangers - 3/8 in. formed angle mounted to underside of Structural Channel Construction - Available upon request.
conveyor. Hanging hardware not included. See page 161.
Standard Specifications:
Models Available - Incline belt conveyors are available in Leg Supports - Adjustable floor supports are available up to 84 in.
the bolt-together galvanized series (Light Duty) as well as the top of leg. Ceiling hangers are recommended above 7 ft. One
welded series (Medium Duty, Heavy Duty and Extra Heavy support is required at every bed joint and at the ends of the
Belt Conveyors
FINGER GUARD
BED
Light Duty Slider Bed Model LENGTH 12"
LIFT
ADJUSTABLE SUPPORT
(TOP OF BELT)
ADJUSTABLE SUPPORT
(TOP OF BELT)
Optional Equipment:
Belt Conveyors
Slaved Power Infeed - Separate belt slave driven by roller chain Other - Additional options listed on previous pages for the
from tail pulley of inclined conveyor. Center take-up required for specific series required.
incline belt. Contact sales engineer for reversing applications.
Belt - Gum Rubber Ruff Top, Nitrile Ruff Top, White PVC-120 Ruff
Top. Other types available.
Standard Specifications:
Belt - Polyester carcass with black PVC cover. Food grade and Belt Guiding System - Belt is mechanically guided at outside rail
other belts available. with wheel. These wheels provide quiet operation, minimal friction and
Frame - 10 ga. steel frame and slider bed pan. Rigid welded require virtually no maintenance.
construction. Conveying Speed - Constant 60 FPM at belt centerline. Speeds
Belt Conveyors
Floor Supports - 4 in. structural channel legs with 4 in. available up to 300 FPM. Fixed or variable speed.
adjustment. Available up to 36 in. top of leg as standard, up to Speed Reduction - Sealed worm gear “C” face hollow shaft speed
84 in. top of leg possible as option. Ceiling hangers available. reducer.
Drive and Tail Pulleys - Tapered pulley with ruff-top lagging. Motor - 230/460 V - 3 phase - 60 Hz. - totally enclosed, fan cooled.
Bearings - Sealed, pre-lubricated, self-aligning ball bearings on Electrical Controls - Available as option.
drive and tail pulleys.
12 36 42 200
18 30 39
48 6 7/8 20 1/4 8 3/4 1 3/16
20 28 38
24 24 36
24 36 48
60 30 30 45 8 24 1/4 9 7/8 1 7/16 300
36 24 42
36 36 54
72 42 30 51 8 7/8 28 1/4 10 3/4 350
48 24 48
1 11/16
36 51 69
87 42 45 66 8 24 1/8 9 7/8 400
48 39 63
Standard Specifications:
Belt - Polyester carcass with black PVC cover. Food grade and Belt Guiding System - Belt is mechanically guided at outside
other belts available. rail with wheel. These wheels provide quiet operation, minimal
Frame - 10 ga. steel frame and slider bed pan. Rigid welded friction and require virtually no maintenance.
construction. Conveying Speed - Constant 60 FPM at belt centerline.
Floor Supports - 4 in. structural channel legs with 4 in. adjustment. Speeds available up to 200 FPM. Fixed or variable speed.
Available up to 36 in. top of leg as standard, up to 84 in. top of leg Speed Reduction - Sealed worm gear “C” face hollow shaft
Belt Conveyors