Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LED TV
SERVICE MANUAL
CHASSIS : LD36M
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS . ............................................................................................. 2
SPECIFICATION ....................................................................................... 6
Copyright © LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
Copyright © LG Electronics. Inc. All rights reserved. -3- LGE Internal Use Only
Only for training and service purposes
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder
on page 3 of this publication, always follow the safety precau- ES devices.
tions. Remember: Safety First. 4. Use only an anti-static type solder removal device. Some sol-
der removal devices not classified as “anti-static” can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board 6. Do not remove a replacement ES device from its protective
module or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug (Most replacement ES devices are packaged with leads elec-
or other electrical connection. trically shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective mate-
installation of electrolytic capacitors may result in an explo- rial to the chassis or circuit assembly into which the device will
sion hazard. be installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or cir-
high voltage meter or other voltage measuring device (DVM, cuit, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropri-
(by volume) isopropyl alcohol (90 % - 99 % strength) ate tip size and shape that will maintain tip temperature within
CAUTION: This is a flammable mixture. the range or 500 °F to 600 °F.
Unless specified otherwise in this service manual, lubrication 2. Use an appropriate gauge of RMA resin-core solder composed
of contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks Do not use freon-propelled spray-on cleaners.
are correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 °F to 600 °F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 °F to 600 °F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand
ily by static electricity. Such components commonly are called against the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor “chip” components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharg-
ing wrist strap device, which should be removed to prevent
potential shock reasons prior to applying power to the unit
under test.
Copyright © LG Electronics. Inc. All rights reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed when-
gently prying up on the lead with the soldering iron tip as the ever this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. Carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remain- good copper pattern. Solder the overlapped area and clip off
ing on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the
lead of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and
if necessary, apply additional solder.
Copyright © LG Electronics. Inc. All rights reserved. -5- LGE Internal Use Only
Only for training and service purposes
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the LED TV used LD36M chassis.
3. Test method
(1) Performance: LGE TV test method followed
(2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC specification
Model Market Appliance
32LN520B-ZA
Safety : IEC/EN60065
32LN5203-ZA
EU (PAL/DVB Market) EMI : EN55013
42LN5200-ZA
EMS : EN55020
42LN5204-ZA
Copyright © LG Electronics. Inc. All rights reserved. -6- LGE Internal Use Only
Only for training and service purposes
4. Model General Specification
No. Item Specification Remarks
1 Market EU(PAL Market-37Countries) DTV & Analog (Total 37 countries)
Copyright © LG Electronics. Inc. All rights reserved. -7- LGE Internal Use Only
Only for training and service purposes
5. External Input Support format
5.1. HDMI Input 1 (PC/DTV)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark
PC(DVI) DDC
1 640*350 31.468 70.09 25.17 EGA X
2 720*400 31.469 70.08 28.32 DOS O
3 640*480 31.469 59.94 25.17 VESA(VGA) O
4 800*600 37.879 60.31 40.00 VESA(SVGA) O
5 1024*768 48.363 60.00 65.00 VESA(XGA) O
6 1152*864 54.348 60.053 80.00 VESA O
7 1360*768 47.712 60.015 85.50 VESA (WXGA) O
8 1280*1024 63.981 60.020 108.0 VESA (SXGA) O FHD only
9 1920*1080 67.50 60.00 148.5 HDTV 1080P O FHD only
DTV
1 720*480 31.47 59.94 27.00 SDTV 480P
2 720*480 31.50 60.00 27.027 SDTV 480P
3 720*576 31.250 50.00 27.00 SDTV 576P
4 1280*720 37.50 50.00 74.25 HDTV 720P
5 1280*720 45.00 60.00 74.25 HDTV 720P
6 1280*720 44.96 59.94 74.176 HDTV 720P
7 1920*1080 28.125 50.00 74.25 HDTV 1080I
8 1920*1080 33.75 60.00 74.25 HDTV 1080I
9 1920*1080 33.72 59.94 74.176 HDTV 1080I
10 1920*1080 56.250 50.00 148.50 HDTV 1080P
11 1920*1080 67.50 60.00 148.50 HDTV 1080P
12 1920*1080 67.432 59.94 148.352 HDTV 1080P
13 1920*1080 27.00 24.00 74.25 HDTV 1080P
14 1920*1080 26.97 23.976 74.176 HDTV 1080P
15 1920*1080 33.75 30.00 74.25 HDTV 1080P
Copyright © LG Electronics. Inc. All rights reserved. -8- LGE Internal Use Only
Only for training and service purposes
5.3. USB Input format
Category Item Specification Remark
Slide Show support.
Photo JPG, PNG, BMP, TIF, TIFF, GIF 4096X4096 Background music
support
32kbps ~ 320kbps(Bit rate)
MP3
32kHz ~ 48kHz(Sample rate)
128bps ~ 320kbps(Bit rate)
Music WMA
8kHz ~ 48kHz(Sample rate)
1.44kbps(Bit rate)
WAV
44.1kHz(Sample rate)
Category Codec Media Container Profile/Level Support Remark
MPEG1/ DAT, MPG, MPEG,
1920X1080 @ 30I
MPEG2 DVD, TS, TRP, TP
MPEG4
(Divx 3.11, Divx 4.12, Divx 5.x,
AVI, DIVX, MP4,
Video Divx 6, Divx HD, Xvid 1.00, 1920X1080 @ 30P
MKV, TS, TRP
Xvid 1.01, Xvid 1.02, Xvid 1.03,
Xvid 1.10-beta1/2 )
AVI, MP4, MKV, TS,
H.264 1920X1080 @ 30P
TRP, TP
32kbps ~ 320kbps(Bit rate)
MP3, MP3 Pro MP3
32kHz ~ 48kHz(Sample rate)
32kbps ~ 640kbps(Bit rate)
AC3 AC3
32kHz, 44.1kHz, 48kHz(Sample rate)
32kbps ~ 448kbps(Bit rate)
MPEG MPA
32kHz ~ 48kHz(Sample rate)
24kbps ~ 3844kbps(Bit rate)
Audio AAC, HEAAC M4A
8kHz ~ 96kHz(Sample rate)
Movie
1.44kbps(Bit rate)
CDDA CDA
44.1kHz(Sample rate)
1.41Mbps ~ 9.6Mbps(Bit rate)
Multi-channel 44.1kHz, 88.2kHz
LPCM AIF, AIFF, WAV (Sample rate)
48kHz, 96kHz (Sample rate) Stereo
176.4kHz, 192kHz(Sample rate)
a. Pause & Resume
b. Fast forward (2x, 4x, 8x, 16x, 32x)
c. Fast backward (2x, 4x, 8x, 16x,
Trick play
32x)
d. Forward slow motion (1/2x, 1/4x,
ETC 1/8x, 1/16x, 1/32x)
Can support video zoom in/out proc-
Variable video size(Full/Original)
ess when the video is display.
Video Preview Can support movie preview. But in
(Movie Preview function is possible or not. like fast play preview mode, we don't support any
or thumbnail when user move the cursor in the list) trick mode process.
Copyright © LG Electronics. Inc. All rights reserved. -9- LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTION
1. Application Range (4) Click "Connect" tab. If "Can't" is displayed, check connection
between computer, jig, and set.
This specification sheet is applied to all of the LED TV with
LD36M chassis.
(2) (3)
2. Designation
(1) The adjustment is according to the order which is designated
and which must be followed, according to the plan which
can be changed only on agreeing.
(2) Power adjustment : Free Voltage.
(3) Magnetic Field Condition: Nil.
(4) Input signal Unit: Product Specification Standard.
(5) Reserve after operation : Above 5 Minutes (Heat Run) Please Check the Speed :
Temperature : at 25 °C ± 5 °C To use speed between
Relative humidity : 65 ± 10 % from 200KHz to 400KHz
Input voltage : 220 V, 60 Hz
(6) Adjustment equipments: Color Analyzer(CA-210 or CA-110), (5) Click "Auto" tab and set as below.
DDC Adjustment Jig, Service remote control. (6) Click "Run".
(7) Push the "IN STOP" key - For memory initialization. (7) After downloading, check "OK" message.
Copyright © LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
* After downloading, have to adjust Tool Option again. 3.3. EDID data
(1) Push "IN-START" key in service remote control. (1) HD HDMI EDID data(2D Model)
(2) Select "Tool Option 1" and push "OK" key. 0 1 2 3 4 5 6 7 8 9 A B C D E F
(3) Punch in the number. (Each model has their number) 00 00 FF FF FF FF FF FF 00 1E 6D a b
(4) Completed selecting Tool option. 10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
3.1. ADC Process 40 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30
* If ADC processes as OTP, There is no need to proceed 50 18 88 03 06 40 84 63 00 00 18 00 00 00 FD 00 3A
internal ADC. 60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d
70 d 01 e
- Enter Service Mode by pushing "ADJ" key,
80 02 03 22 F1 4E 10 1F 04 93 05 14 03 02 12 20 21
- Enter Internal ADC mode by pushing "►" key at "7. ADC
90 22 15 01 26 15 07 50 09 57 07 f
Calibration". A0 80 1E 01 1D 80 18 71 1C 16 20 58 2C 25 00 A0 5A
EZ ADJUST ADC Calibration B0 00 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00
0. Tool Option1 ADC Comp 480i OK C0 20 C2 31 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E
1. Tool Option2 ADC Comp 1080p OK D0 96 00 A0 5A 00 00 00 18 02 3A 80 18 71 38 2D 40
2. Tool Option3 ADC Type ◄ OTP ►
3. Tool Option4 E0 58 2C 45 00 A0 5A 00 00 00 1E 00 00 00 00 00 00
4. Tool Option5 Start Reset
F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e
5. Tool Option Commercial
6. Country Group
7. Area Option
8.ADC Calibration ►
(2) FHD HDMI EDID data(2D Model)
9. White Balance 0 1 2 3 4 5 6 7 8 9 A B C D E F
10. 10 Point WB 00 00 FF FF FF FF FF FF 00 1E 6D a b
11. Test Pattern
10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
12 EDID D/L
13. Sub B/C 20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
14. Ext. Input Adjust 30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30
50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A
<Caution> U sing "P-ONLY" key of the Adjustment remote
60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d
control, power on TV.
70 d 01 e
80 02 03
22 F1 4E 10 9F 04 13 05 14 03 02 12 20 21
* ADC Calibration Protocol (RS232) 90 22 15
01 26 15 07 50 09 57 07 f
NO Item CMD 1 CMD 2 Data 0 A0 f 01 1D 80 18 71 1C 16 20 58 2C 25 00 20 C2
Enter Adjust When transfer the ‘Mode In’, B0 31 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00
A A 0 0
Adjust MODE ‘Mode In’ Carry the command. C0 20 C2 31 00 00 1E 02 3A 80 18 71 38 2D 40 58 2C
Automatically adjustment D0 45 00 A0 5A 00 00 00 1E 01 1D 00 BC 52 D0 1E 20
ADC adjust ADC Adjust A D 1 0
(The use of a internal pattern) E0 B8 28 55 40 C4 8E 21 00 00 1E 00 00 00 00 00 00
F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e
Adjust Sequence (3) Detail EDID Options are below
▪ aa 00 00 [Enter Adjust Mode] a. Product ID
▪ xb 00 40 [Component Input480i)]
MODEL NAME HEX EDID Table DDC Function
▪ ad 00 10 [Adjust 480i & 1080p Comp]
▪ aa 00 90 End Adjust mode HD/FHD Model 0001 01 00 Analog/Digital
* Required equipment : Adjustment remote control. b. Serial No: Controlled on production line.
c. Month, Year: Controlled on production line:
3.2. EDID Download ex) Week : '01' -> '01'
▪ After enter Service Mode by pushing "ADJ" key. Year : '2013' -> '17' fix
▪ Enter EDID D/L menu. d. Model Name(Hex):
▪ Enter "START" by pushing "OK" key. cf) TV set’s model name in EDID data is below.
EZ ADJUST EDID D/L Model name MODEL NAME(HEX)
0. Tool Option1 HDMI1 NG
1. Tool Option2 HDMI2 NG
LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)
2. Tool Option3 Start Reset
3. Tool Option4
e. Checksum: Changeable by total EDID data.
4. Tool Option5
5. Tool Option Commercial HD
6. Country Group EDID C/S data
7. Area Option HDMI
8. ADC Calibration
Block 0 A3
Check sum
9. White Balance
10. 10 Point WB
5B (HDMI1)
11. Test Pattern (Hex) Block 1
12. EDID D/L ► 4B (HDMI2)
13. Sub B/C
14. Ext. Input Adjust
f. Vendor Specific(HDMI)
<Caution> Never connect HDMI cable when EDID downloaded. Input Model name(HEX)
HDMI1 67030C001000801E
HDMI2 67030C002000801E
Copyright © LG Electronics. Inc. All rights reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
3.4. Function Check ▪ Normal line(LGD/CMI, March ~ December for Gumi, Global)
- Check display and sound Cool Medium Warm
Aging time
■ Check Input and Signal items. NetCase4 X y x y x y
(Min)
1) TV 271 270 285 293 313 329
2) AV (SCART / CVBS) 1 0-2 281 287 295 310 320 342
3) HDMI 2 3-5 280 285 294 308 319 340
* Display and Sound check is executed by Remote control.
3 6-9 278 284 292 307 317 339
4 10-19 276 281 290 304 315 336
<Caution>
Not to push the INSTOP key after completion if the function 5 20-35 275 277 289 300 314 332
inspection. 6 36-49 274 274 288 297 313 329
7 50-79 273 272 287 295 312 327
8 80-119 272 271 286 294 311 326
4. Total Assembly line process 9 Over 120 271 270 285 293 310 325
RS-232C Communication
Copyright © LG Electronics. Inc. All rights reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
* Auto-control interface and directions * CASE Cool Mode
(1) Adjust in the place where the influx of light like floodlight First adjust the coordinate far away from the target
around is blocked. (illumination is less than 10 lux). value(x, y).B.
(2) Adhere closely the Color analyzer(CA210) to the module 1) x, y > target
less than 10 cm distance, keep it with the surface of the 2) x, y < target
Module and Color analyzer's prove vertically.(80° ~ 100°). 3) x >target, y < target
(3) Aging time 4) x < target, y > target
- After aging start, keep the power on (no suspension of -E very 4 case have to fit y value by adjusting B Gain
power supply) and heat-run over 5 minutes. and then fit x value by adjusting R-Gain.
- Using 'no signal' or 'POWER ONLY' or the others, check - In this case, increasing/decreasing of B Gain and R
the back light on. Gain can be adjusted.
* Manual W/B process using adjust Remote control. * After you finished all adjustments, Press "In-start" key and
▪ After enter Service Mode by pushing "ADJ" key, compare Tool option and Area option value with its BOM, if
▪ E nter White Balance by pushing " ► " key at "9. White it is correctly same then unplug the AC cable. If it is not
Balance". same, then correct it same with BOM and unplug AC cable.
EZ ADJUST
For correct it to the model's module from factory Jig model.
0. Tool Option1
* P ush the "IN STOP" key after completing the function
Whit Balance
1. Tool Option2 inspection. And Mechanical Power Switch must be set
2. Tool Option3
3. Tool Option4
Color Temp.
R-Gain
◄ Cool
172
►
“ON”.
4. Tool Option5 G-Gain 172
Copyright © LG Electronics. Inc. All rights reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
5. HI-POT Test 6.3. Method & notice
(1) Serial number D/L is using of scan equipment.
5.1. HI-POT auto-check preparation (2) S etting of scan equipment operated by Manufacturing
- Check the POWER cable and SIGNAL cable insertion condition Technology Group.
(3) Serial number D/L must be conformed when it is produced in
5.2. HI-POT auto-check production line, because serial number D/L is mandatory by
(1) Pallet moves in the station. (POWER CORD / AV CORD is D-book 4.0.
tightly inserted)
(2) Connect the AV JACK Tester. * Manual Download(Model Name and Serial Number)
(3) Controller (GWS103-4) on. If the TV set is downloaded by OTA or Service man, sometimes
model name or serial number is initialized.(Not always)
(4) HI-POT test (Auto)
There is impossible to download by bar code scan, so It need
- If Test is failed, Buzzer operates.
Manual download.
- If Test is passed, GOOD Lamp on and move to next proc- 1) Press the "Instart" key of Adjustment remote control.
ess automatically. 2) Go to the menu "6.Model Number D/L" like below photo.
3) Input the Factory model name(ex 32LN520B-ZA) or Serial
5.3. Checkpoint number like photo.
(1) Test voltage
- Touchable Metal : 3 KV / min at 100 mA
- SIGNAL : 3 KV / min at 100 mA
(2) TEST time: 1 second. (case : mass production )
(3) TEST POINT
- Touchable Metal => LIVE & NEUTRAL : Touchable Metal.
- SIGNAL => LIVE & NEUTRAL : SIGNAL.
6. Model name & Serial number D/L 4) Check the model name Instart menu → Factory name displayed
▪ Press "Power on" key of service remote control.
(ex 32LN520B-ZA)
(Baud rate : 115200 bps)
5) Check the Diagnostics (DTV country only) → Buyer model
▪ Connect RS232 Signal Cable to RS-232 Jack.
displayed (ex 32LN520B-ZA)
▪ Write Serial number
▪ Must check the serial number at the Diagnostics of SET UP menu.
(Refer to below).
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n
Delay : 20ms
Copyright © LG Electronics. Inc. All rights reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
7. MAC Address & CI+ key download
7.1 MAC Address
7.1.1 Equipment & Condition
▪ Play file : Serial.exe
▪ MAC Address edit
▪ Input Start / End MAC address
GP4_LOW
Copyright © LG Electronics. Inc. All rights reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
SCREW ASSEMBLY WORKING GUIDE
■ Screw specification and application situation
A A
A
• FAB31339403
B • 4EA
B B
A A
A A
• FAB31639801
(M4*L10, BK, Taptite) C C
• 9EA
• FAB30016124
(M4*L14, BK, Machine)
• 2EA
<Warning>
Check Screw Type When Screw is assembled at 'A' Part. If 'B' Screw is used at the 'A'
part, Module will get damaged.
Copyright © LG Electronics. Inc. All rights reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
DISASSEMBLY WORKING GUIDE
1 2
3 4
Disassemble 4 screws that fix Side AV bracket and After opening cover of IR Ass’y Disconnect IR cable
Back-cover.
5 6
Copyright © LG Electronics. Inc. All rights reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
Copyright ©
1. MAIN
TV Tuner
DDR3 2Gbit
PCMCIA (SIDE)
CI_ADDR[0:14] (15) CI_ADDR[8:14] SPI SCK/SDI Serial Flash, 8Mbit
(7)
(MACRONIX)
MAIN IC IC1300
CI_ADDR[0:7]
MSTAR USB_DM/DP
- 18 -
(8)
MSD804KKX USB (SIDE)
IC101
Buffer
IC1902
SCL/SDA, Data (10)
HDMI2
NAND flash PCM_A[0:7] (8)
BLOCK DIAGRAM
24V_Adapter
24V LED Driver
24V
- 19 -
DCDC,IC NAND, MAIN IC
2.5V
IC402
MAIN IC
LDO
IC2603 1.8V
TU
LDO
IC403 1.1V
DCDC,IC MIAN IC Core
IC407 1.5V
DDR
LDO
NVRAM, MAIN IC
Copyright ©
S7LRM
+3.3V_NORMAL +3.3V_TU
- 20 -
TU_SDA/SCL
+3.3V_NORMAL +3.3V_NORMAL
1KΩ 1KΩ
910
900
591
400
590
540
120
LV1
521
Set + Stand
A10
Stand Base
Stand Body
A9
+
A31
200
A2
Copyright © LG Electronics. Inc. All rights reserved. - 21 - LGE Internal Use Only
Only for training and service purposes
IR/LED and Control
+3.5V_ST
CONTROL_NO_FILTER
R602 R603 R611
10K 10K 0
1% 1%
CONTROL_FILTER
L601
R600 BLM18PG121SN1D
100
KEY1
CONTROL_FILTER
CONTROL_FILTER C608 P600
L602 0.1uF
R601 BLM18PG121SN1D 16V 12507WR-08L
100
KEY2
CONTROL_FILTER
C609 1
CONTROL_NO_FILTER
R612 0.1uF
0 16V
2
+3.5V_ST 3
L600
BLM18PG121SN1D
4
R610
1.8K
C602 C603 LED_R/BUZZ 5
+3.5V_ST 0.1uF 1000pF
16V 50V
OPT
C607
0.1uF 6
R607 16V
3.3K
IR 7
C604
100pF
50V 8
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
USB (SIDE)
+5V_USB
OPT C700
ZD700
22uF
5V
10V
JK700
3AU04S-305-ZC-(LG)
1
USB DOWN STREAM
SIDE_USB1_DM
3
SIDE_USB1_DP
4
D700
5
RCLAMP0502BA
OPT
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Serial Flash for SPI boot(OS)
+3.5V_ST +3.5V_ST
SPI_FLASH_MACRONIX
OPT IC1300
R1301
+3.5V_ST 4.7K MX25L8006EM2I-12G
C1300
CS# VCC 0.1uF
/SPI_CS 1 8
OPT
R1300
10K SO/SIO1 HOLD#
SPI_SDO 2 7
WP# SCLK
/FLASH_WP 3 6 SPI_SCK
R1302
GND SI/SIO0 33
4 5 SPI_SDI
SPI_FLASH_WINBOND
IC1300-*1
W25Q80BVSSIG
CS VCC
1 8
DO[IO1] HOLD[IO3]
2 7
%WP[IO2] CLK
3 6
GND DI[IO0]
4 5
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
CI Region * Option name of this page : CI_SLOT
(because of Hong Kong)
CI SLOT
+5V_CI_ON
CI_DATA[0-7]
CI TS INPUT
CI_DATA[0-7]
+5V_Normal AR1905 33
C1906 FE_TS_DATA[7]
CI_MDI[7]
10uF FE_TS_DATA[6]
10V CI_MDI[6]
FE_TS_DATA[0-7]
R1903 FE_TS_DATA[5]
CI_MDI[5]
10K FE_TS_DATA[4]
CI_SLOT_JACK CI_MDI[4]
/CI_CD1 P1901
10067972-000LF
AR1906 33 FE_TS_DATA[3]
R1908 35 1 CI_MDI[3]
100 CI_DATA[3] FE_TS_DATA[2]
36 2 CI_MDI[2] FE_TS_DATA[1]
AR1901 CI_DATA[4]
CI_DATA[0-7]
33 37 3 CI_MDI[1] FE_TS_DATA[0]
CI_DATA[5] R1921
CI_TS_DATA[4] 38 4 10K CI_MDI[0]
CI_DATA[6]
CI_TS_DATA[5] 39 5
CI_DATA[7] FE_TS_DATA[0-7]
CI_TS_DATA[6] 40 6
R1919 R1928 33
CI_TS_DATA[7] 41 7 47 CI_MISTRT FE_TS_SYNC
CI_ADDR[10] /PCM_CE R1929 33
42 8 CI_MIVAL_ERR FE_TS_VAL_ERR
R1905 10K R1930 100
43 9 CI_OE CI_MCLKI FE_TS_CLK
CI_ADDR[11]
CI_IORD 44 10 +5V_Normal
CI_ADDR[9]
CI_IOWR 45 11
CI_ADDR[8]
46 12 R1910
CI_ADDR[13] 10K
CI_MDI[0] 47 13
CI_ADDR[14]
CI_MDI[1] 48 14
CI_MDI[2] 49 15 CI_WE
50 16 R1920 100
CI_MDI[3] /PCM_IRQA
51 17
GND
C1905
0.1uF
52
53
18
19
C1909
0.1uF
C1901
0.1uF
CI HOST I/F
CI_MDI[4]
GND
CI_MDI[5] 54 20
+5V_Normal CI_ADDR[12]
CI_MDI[6] 55 21 CLOSE TO MSTAR
CI_ADDR[7]
R1909 CI_MDI[7] 56 22 GND +3.3V_Normal
10K R1906 10K CI_ADDR[6]
57 23
R1902 CI_ADDR[5]
47 58 24
PCM_RST CI_ADDR[4]
R1901 47 CI_DET
/PCM_WAIT 59 25 IC1902
CLOSE TO MSTAR CI_ADDR[3]
REG 60 26 C1913
R1925 100 CI_ADDR[2]
CI_TS_CLK 61 27 0.1uF
R1926 33 CI_ADDR[1] 1OE VCC 16V
CI_TS_VAL 62 28 1 20
R1927 33 CI_ADDR[0] TOSHIBA
CI_TS_SYNC 63 29
CI_DATA[0]
64 30 1A1 2OE
AR1903 33 CI_DATA[1] 2 19
65 31 CI_ADDR[0-14] PCM_A[0]
CI_TS_DATA[0] CI_DATA[2] AR1915 0ITO742440D AR1914
66 32 100
CI_TS_DATA[1] 2Y4 1Y1 100
67 33 3 18
CI_TS_DATA[2] CI_ADDR[7] CI_ADDR[0]
68 34
CI_TS_DATA[3] CI_ADDR[6] CI_ADDR[1]
G2 69 G1 CI_ADDR[5] 1A2 2A4 CI_ADDR[2]
PCM_A[1] 4 17 PCM_A[7]
R1907 CI_ADDR[4] CI_ADDR[3]
100
/CI_CD2 2Y3 1Y2
TC74LCX244FT
+5V_Normal GND 5 16
2Y1 1Y4
CI_MISTRT 9 12
CI_MIVAL_ERR
GND 2A1
10 11 PCM_A[4]
CI_MCLKI
CI DETECT +3.3V_Normal
OR_GARE_CI_PHILIPS
IC1901
74LVC1G32GW +3.3V_Normal
B 1 5 VCC
/CI_CD2
A 2 AR1907 33
/CI_CD1 CI_DATA[0] PCM_D[0]
GND 3 4 Y R1917 CI_DATA[1] PCM_D[1]
10K
CI_DATA[0-7]
CI_DATA[2] PCM_D[2]
CI_DATA[3] PCM_D[3]
OR_GARE_CI_TI
IC1901-*1
SN74LVC1G32DCKR
CI_DET
PCM_D[0-7]
R1911
A VCC 47 AR1908 33
1 5 CI_DATA[4] PCM_D[4]
/PCM_CD
B
2
CI_DATA[5] PCM_D[5]
GND Y
CI_DATA[6] PCM_D[6]
3 4
CI_DATA[7] PCM_D[7]
PCM_D[0-7]
CI_DATA[0-7]
R1913
10K
AR1909 33
CI_OE /PCM_OE
CI_WE /PCM_WE
CI_IORD /PCM_IORD
CI_IOWR /PCM_IOWR
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
AUDIO AMP(STA380BWEF)
COIL_ABCO
L3402
NC_12
NC_11
NC_10
10uH
NC_9
NC_8
NC_7
NC_6
NC_5
NC_4
NC_3
NC_2
NC_1
+3.3V_Normal SPK_L+
C3420 C3424
0.22uF 1000pF
R3408 R3409 C3418 50V 50V
24
23
22
21
20
19
18
17
16
15
14
13
43 43
0.22uF
12 GND_REG C3409 SPEAKER_L
0.1uF COIL_ABCO 50V
NC_13 25 C3413 C3421 C3425
11 VDD_REG 16V L3403
C3403 26 330pF 10uH 0.22uF 1000pF
NC_14 10 OUT1A
0.1uF 50V 50V 50V
NC_15 27 SPK_L-
16V 9 GND1
VDDDIG1 28
8 VCC1
GNDDIG1 29
7 OUT1B
FFX3A 30 IC3401 6 OUT2A COIL_ABCO
31
FFX3B STA380BWF 5 VCC2 L3404
EAPD/FFX4A 32 10uH
C3404 4 GND2
2.2uF TWARNEXT/FFX4B 33 SPK_R+
3 OUT2B C3414 C3422 C3426
10V 34 49
VREGFILT THERMAL
2 VSS_REG 330pF 0.22uF 1000pF
C3408
AGNDPLL 35 50V C3419 50V 50V
1 VCC_REG 0.1uF
36 16V 0.22uF SPEAKER_R
MCLK R3410 R3411
37
38
39
40
41
42
43
44
45
46
47
48
43 43 COIL_ABCO 50V
L3405 C3423 C3427
0.22uF 1000pF
SDI
RESET
PWDN
INTLINE
SDA
SCL
SA
TESTMODE
GNDDIG2
VDDDIG2
[EP]
BICKI 10uH
LRCKI 50V 50V
SPK_R-
+3.5V_ST AUD_MASTER_CLK
+24V
AUD_SCK +3.3V_Normal L3401
UBW2012-121F
AUD_LRCK
R3402
10K
AUD_LRCH
C3407 C3411 C3412 C3415 C3416 C3417
R3403 0.1uF 0.1uF 1uF 1uF 0.1uF 10uF
10K 16V 50V 50V 50V 50V 35V
3216
R3404
100 AMP_RESET
C R3406 0
R3401
10K B Q3401 C3401 AMP_SDA
AMP_MUTE MMBT3904(NXP) 1000pF R3407 0
50V AMP_SCL
E
P3401
WAFER-ANGLE
OPT
R3405
0 SPK_L+
4
POWER_DET
SPK_L-
3
SPK_R+
2
SPK_R-
1
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
MSTART DEBUG_4PIN
MSTAR_DEBUG_4P
P3900
JP_GND1
JP_GND2
JP_GND3
JP_GND4
12505WS-04A00
3 RGB_DDC_SCL
4 RGB_DDC_SDA
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
RS-232C
RS232C_DEBUG_4P
+3.5V_ST P4000
12507WS-04L
R4001
100 VCC
PM_TXD 1
R4000
100 PM_RXD
2
PM_RXD
GND
3
RM_TXD
4
GND
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
EU NOT USED TP (ERRC)
BR_RESET_DEMOD
RF_SWITCH_CTL
HP_ROUT
HP_LOUT
SIDE_HP_MUTE
HP_DET
EPHY_TN
EPHY_RN
EPHY_TP
EPHY_RP
LNA_CTRL_1
LNA_CTRL_2
LNA2_CTL
IF_AGC_SEL
DEMOD_SDA
DEMOD_SCL
S2_RESET
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
+1.5V_DDR +1.5V_DDR
+1.5V_DDR
R1201
R1204
1K 1%
1K 1%
10uF10V
C1217
C1218
C1219
C1238
C1241
0.1uF
0.1uF
C1206
C1239
C1251
A-MVREFDQ A-MVREFCA
1uF
1uF
1uF
1uF
1uF
0.1uF
0.1uF
1000pF
1000pF
1%
1%
R1202
R1205
C1202
C1204
C1201
C1203
1K
1K
CLose to DDR3 CLose to Saturn7M IC
DDR_1600_2G_HYNIX
IC1201 IC101
H5TQ2G63DFR-PBC MSD804KKX
EAN61829203
M8 N3 A11
S7LR-M_NON_MS10 B23
A-MVREFCA VREFCA A0
A1
P7
A-MA0
A-MA1
A-MA0
A-MA1
C14
A_DDR3_A[0]
A_DDR3_A[1]
SYMBOL.B B_DDR3_A[0]
B_DDR3_A[1]
D25
P3 B11 F22
A2 A-MA2 A-MA2 A_DDR3_A[2] B_DDR3_A[2]
H1 N2 F12 G22
A-MVREFDQ VREFDQ A3 A-MA3 A-MA3 A_DDR3_A[3] B_DDR3_A[3]
P8 C15 E24
A4 A-MA4 A-MA4 A_DDR3_A[4] B_DDR3_A[4]
P2 E12 F21
R1203 A5 A-MA5 A-MA5 A_DDR3_A[5] B_DDR3_A[5]
L8 R8 A14 E23
ZQ A6 A-MA6 A-MA6 A_DDR3_A[6] B_DDR3_A[6]
+1.5V_DDR 240 R2 D11 D22
A7 A-MA7 A-MA7 A_DDR3_A[7] B_DDR3_A[7]
1% T8 B14 D24
A8 A-MA8 A-MA8 A_DDR3_A[8] B_DDR3_A[8]
B2 R3 D12 D21
VDD_1 A9 A-MA9 A-MA9 A_DDR3_A[9] B_DDR3_A[9]
10V 10uF C1205 D9 L7 C16 C24
VDD_2 A10/AP A-MA10 A-MA10 A_DDR3_A[10] B_DDR3_A[10]
10V 10uF C1227 G7 R7 C13 C25
VDD_3 A11 A-MA11 A-MA11 A_DDR3_A[11] B_DDR3_A[11]
C1207 0.1uF K2 N7 A15 F23
VDD_4 A12/BC A-MA12 A-MA12 A_DDR3_A[12] B_DDR3_A[12]
C1208 0.1uF K8 T3 E11 E21
VDD_5 A13 A-MA13 A-MA13 A_DDR3_A[13] B_DDR3_A[13]
C1210 0.1uF N1 B13 D23
VDD_6 A-MA14 A_DDR3_A[14] B_DDR3_A[14]
C1211 0.1uF N9 M7
VDD_7 NC_5
C1212 0.1uF R1
VDD_8
C1213 0.1uF R9 M2 F13 G20
VDD_9 BA0 A-MBA0 A-MCK A-MBA0 A_DDR3_BA[0] B_DDR3_BA[0]
R1235
C1214 0.1uF N8 B15 F24
A-MBA1 A-MBA1
1%
BA1 A_DDR3_BA[1] B_DDR3_BA[1]
M3 E13 F20
56
C1215 0.1uF A-MBA2 A-MBA2
BA2 A_DDR3_BA[2] B_DDR3_BA[2]
A1 C1209
VDDQ_1
R1236
A8 J7 C17 G25
0.01uF A-MCK
1%
VDDQ_2 CK A_DDR3_MCLK B_DDR3_MCLK
C1 K7 50V A17 G23
56
VDDQ_3 CK A-MCKB A_DDR3_MCLKZ B_DDR3_MCLKZ
C9 K9 B16 F25
VDDQ_4 CKE A-MCKE A-MCKE A_DDR3_MCLKE B_DDR3_MCLKE
D2
VDDQ_5 A-MCKB
E9 L2
VDDQ_6 CS
F1 K1 E14 D20
VDDQ_7 ODT A-MODT A-MODT A_DDR3_ODT B_DDR3_ODT
H2 J3 +1.5V_DDR B12 B25
VDDQ_8 RAS A-MRASB A-MRASB A_DDR3_RASZ B_DDR3_RASZ
H9 K3 A12 B24
VDDQ_9 CAS A-MCASB R1231 A-MCASB A_DDR3_CASZ B_DDR3_CASZ
L3 C12 A24
WE A-MWEB 10K A-MWEB A_DDR3_WEZ B_DDR3_WEZ
J1
NC_1
J9 T2 F11 E20
NC_2 RESET A-MRESETB A-MRESETB A_DDR3_RESET B_DDR3_RESET
L1
NC_3
L9
NC_4
T7 F3 B19 K24
A-MA14 NC_6 DQSL A-MDQSL A-MDQSL A_DDR3_DQSL B_DDR3_DQSL
G3 C18 K25
DQSL A-MDQSLB A-MDQSLB A_DDR3_DQSLB B_DDR3_DQSLB
A9 C7 B18 J21
VSS_1 DQSU A-MDQSU A-MDQSU A_DDR3_DQSU B_DDR3_DQSU
B3 B7 A18 J20
VSS_2 DQSU A-MDQSUB A-MDQSUB A_DDR3_DQSUB B_DDR3_DQSUB
E1
VSS_3
G8 E7 E15 H24
VSS_4 DML A-MDML A-MDML A_DDR3_DQML B_DDR3_DQML
J2 D3 A21 L20
VSS_5 DMU A-MDMU A-MDMU A_DDR3_DQMU B_DDR3_DQMU
J8
VSS_6
M1 E3 D17 L23
VSS_7 DQL0 A-MDQL0 A-MDQL0 A_DDR3_DQL[0] B_DDR3_DQL[0]
M9 F7 G15 J24
VSS_8 DQL1 A-MDQL1 A-MDQL1 A_DDR3_DQL[1] B_DDR3_DQL[1]
P1 F2 B21 L24
VSS_9 DQL2 A-MDQL2 A-MDQL2 A_DDR3_DQL[2] B_DDR3_DQL[2]
P9 F8 F15 J23
VSS_10 DQL3 A-MDQL3 A-MDQL3 A_DDR3_DQL[3] B_DDR3_DQL[3]
T1 H3 B22 M24
VSS_11 DQL4 A-MDQL4 A-MDQL4 A_DDR3_DQL[4] B_DDR3_DQL[4]
T9 H8 F14 H23
VSS_12 DQL5 A-MDQL5 A-MDQL5 A_DDR3_DQL[5] B_DDR3_DQL[5]
G2 A22 M23
DQL6 A-MDQL6 A-MDQL6 A_DDR3_DQL[6] B_DDR3_DQL[6]
H7 D15 K23
DQL7 A-MDQL7 A-MDQL7 A_DDR3_DQL[7] B_DDR3_DQL[7]
B1
VSSQ_1
B9 D7 G16 G21
VSSQ_2 DQU0 A-MDQU0 A-MDQU0 A_DDR3_DQU[0] B_DDR3_DQU[0]
D1 C3 B20 L22
VSSQ_3 DQU1 A-MDQU1 A-MDQU1 A_DDR3_DQU[1] B_DDR3_DQU[1]
D8 C8 F16 H22
VSSQ_4 DQU2 A-MDQU2 A-MDQU2 A_DDR3_DQU[2] B_DDR3_DQU[2]
E2 C2 C21 K20
VSSQ_5 DQU3 A-MDQU3 A-MDQU3 A_DDR3_DQU[3] B_DDR3_DQU[3]
DDR_1600_2G_SS DDR_1600_2G_NANYA DDR_1600_1G_HYNIX DDR_1600_1G_SS DDR_1600_1G_NANYA E8 A7 E16 H20
VSSQ_6 DQU4 A-MDQU4 A-MDQU4 A_DDR3_DQU[4] B_DDR3_DQU[4]
IC1201-*1 IC1201-*2 IC1201-*3 IC1201-*4 IC1201-*5 F9 A2 A20 L21
K4B2G1646E-BCK0 NT5CB128M16FP-DI H5TQ1G63EFR-PBC K4B1G1646G-BCK0 NT5CB64M16DP-DH VSSQ_7 DQU5 A-MDQU5 A-MDQU5 A_DDR3_DQU[5] B_DDR3_DQU[5]
EAN61848802 EAN61859702 EAN61829003 EAN61836301 EAN61859501 G1 B8 D16 H21
N3 M8 N3 M8 N3 M8 N3 M8 N3 M8 VSSQ_8 DQU6 A-MDQU6 A-MDQU6 A_DDR3_DQU[6] B_DDR3_DQU[6]
P7
A0 VREFCA
P7
A0 VREFCA
P7
A0 VREFCA
P7
A0 VREFCA
P7
A0 VREFCA G9 A3 C20 K21
P3
A1
A2
P3
A1
A2
P3
A1
A2
P3
A1
A2
P3
A1
A2 VSSQ_9 DQU7 A-MDQU7 A-MDQU7 A_DDR3_DQU[7] B_DDR3_DQU[7]
N2 H1 N2 H1 N2 H1 N2 H1 N2 H1
A3 VREFDQ A3 VREFDQ A3 VREFDQ A3 VREFDQ A3 VREFDQ
P8 P8 P8 P8 P8
A4 A4 A4 A4 A4
P2 P2 P2 P2 P2
A5 A5 A5 A5 A5
R8 L8 R8 L8 R8 L8 R8 L8 R8 L8
A6 ZQ A6 ZQ A6 ZQ A6 ZQ A6 ZQ
R2 R2 R2 R2 R2
A7 A7 A7 A7 A7
T8 T8 T8 T8 T8
A8 A8 A8 A8 A8
R3 B2 R3 B2 R3 B2 R3 B2 R3 B2
A9 VDD_1 A9 VDD_1 A9 VDD_1 A9 VDD_1 A9 VDD_1
L7 D9 L7 D9 L7 D9 L7 D9 L7 D9
A10/AP VDD_2 A10/AP VDD_2 A10/AP VDD_2 A10/AP VDD_2 A10/AP VDD_2
R7 G7 R7 G7 R7 G7 R7 G7 R7 G7
A11 VDD_3 A11 VDD_3 A11 VDD_3 A11 VDD_3 A11 VDD_3
N7 K2 N7 K2 N7 K2 N7 K2 N7 K2
A12/BC VDD_4 A12/BC VDD_4 A12/BC VDD_4 A12/BC VDD_4 A12 VDD_4
T3 K8 T3 K8 T3 K8 T3 K8 T3 K8
A13 VDD_5 A13 VDD_5 NC_7 VDD_5 A13 VDD_5 NC_6 VDD_5
N1 N1 N1 N1 N1
VDD_6 VDD_6 VDD_6 VDD_6 VDD_6
M7 N9 M7 N9 M7 N9 M7 N9 M7 N9
NC_5 VDD_7 NC_6 VDD_7 NC_5 VDD_7 NC_5 VDD_7 NC_5 VDD_7
R1 R1 R1 R1 R1
VDD_8 VDD_8 VDD_8 VDD_8 VDD_8
M2 R9 M2 R9 M2 R9 M2 R9 M2 R9
BA0 VDD_9 BA0 VDD_9 BA0 VDD_9 BA0 VDD_9 BA0 VDD_9
N8 N8 N8 N8 N8
BA1 BA1 BA1 BA1 BA1
M3 M3 M3 M3 M3
BA2 BA2 BA2 BA2 BA2
A1 A1 A1 A1 A1
VDDQ_1 VDDQ_1 VDDQ_1 VDDQ_1 VDDQ_1
J7 A8 J7 A8 J7 A8 J7 A8 J7 A8
CK VDDQ_2 CK VDDQ_2 CK VDDQ_2 CK VDDQ_2 CK VDDQ_2
K7 C1 K7 C1 K7 C1 K7 C1 K7 C1
CK VDDQ_3 CK VDDQ_3 CK VDDQ_3 CK VDDQ_3 CK VDDQ_3
K9 C9 K9 C9 K9 C9 K9 C9 K9 C9
CKE VDDQ_4 CKE VDDQ_4 CKE VDDQ_4 CKE VDDQ_4 CKE VDDQ_4
D2 D2 D2 D2 D2
VDDQ_5 VDDQ_5 VDDQ_5 VDDQ_5 VDDQ_5
L2 E9 L2 E9 L2 E9 L2 E9 L2 E9
CS VDDQ_6 CS VDDQ_6 CS VDDQ_6 CS VDDQ_6 CS VDDQ_6
K1 F1 K1 F1 K1 F1 K1 F1 K1 F1
ODT VDDQ_7 ODT VDDQ_7 ODT VDDQ_7 ODT VDDQ_7 ODT VDDQ_7
J3 H2 J3 H2 J3 H2 J3 H2 J3 H2
RAS VDDQ_8 RAS VDDQ_8 RAS VDDQ_8 RAS VDDQ_8 RAS VDDQ_8
K3 H9 K3 H9 K3 H9 K3 H9 K3 H9
CAS VDDQ_9 CAS VDDQ_9 CAS VDDQ_9 CAS VDDQ_9 CAS VDDQ_9
L3 L3 L3 L3 L3
WE WE WE WE WE
J1 J1 J1 J1 J1
NC_1 NC_1 NC_1 NC_1 NC_1
T2 J9 T2 J9 T2 J9 T2 J9 T2 J9
RESET NC_2 RESET NC_2 RESET NC_2 RESET NC_2 RESET NC_2
L1 L1 L1 L1 L1
NC_3 NC_3 NC_3 NC_3 NC_3
L9 L9 L9 L9 L9
NC_4 NC_4 NC_4 NC_4 NC_4
F3 T7 F3 T7 F3 T7 F3 T7 F3 T7
DQSL NC_6 DQSL NC_5 DQSL NC_6 DQSL NC_6 DQSL NC_7
G3 G3 G3 G3 G3
DQSL DQSL DQSL DQSL DQSL
C7 A9 C7 A9 C7 A9 C7 A9 C7 A9
DQSU VSS_1 DQSU VSS_1 DQSU VSS_1 DQSU VSS_1 DQSU VSS_1
B7 B3 B7 B3 B7 B3 B7 B3 B7 B3
DQSU VSS_2 DQSU VSS_2 DQSU VSS_2 DQSU VSS_2 DQSU VSS_2
E1 E1 E1 E1 E1
VSS_3 VSS_3 VSS_3 VSS_3 VSS_3
E7 G8 E7 G8 E7 G8 E7 G8 E7 G8
DML VSS_4 DML VSS_4 DML VSS_4 DML VSS_4 DML VSS_4
D3 J2 D3 J2 D3 J2 D3 J2 D3 J2
DMU VSS_5 DMU VSS_5 DMU VSS_5 DMU VSS_5 DMU VSS_5
J8 J8 J8 J8 J8
VSS_6 VSS_6 VSS_6 VSS_6 VSS_6
E3 M1 E3 M1 E3 M1 E3 M1 E3 M1
DQL0 VSS_7 DQL0 VSS_7 DQL0 VSS_7 DQL0 VSS_7 DQL0 VSS_7
F7 M9 F7 M9 F7 M9 F7 M9 F7 M9
DQL1 VSS_8 DQL1 VSS_8 DQL1 VSS_8 DQL1 VSS_8 DQL1 VSS_8
F2 P1 F2 P1 F2 P1 F2 P1 F2 P1
DQL2 VSS_9 DQL2 VSS_9 DQL2 VSS_9 DQL2 VSS_9 DQL2 VSS_9
F8 P9 F8 P9 F8 P9 F8 P9 F8 P9
DQL3 VSS_10 DQL3 VSS_10 DQL3 VSS_10 DQL3 VSS_10 DQL3 VSS_10
H3 T1 H3 T1 H3 T1 H3 T1 H3 T1
DQL4 VSS_11 DQL4 VSS_11 DQL4 VSS_11 DQL4 VSS_11 DQL4 VSS_11
H8 T9 H8 T9 H8 T9 H8 T9 H8 T9
DQL5 VSS_12 DQL5 VSS_12 DQL5 VSS_12 DQL5 VSS_12 DQL5 VSS_12
G2 G2 G2 G2 G2
DQL6 DQL6 DQL6 DQL6 DQL6
H7 H7 H7 H7 H7
DQL7 DQL7 DQL7 DQL7 DQL7
B1 B1 B1 B1 B1
VSSQ_1 VSSQ_1 VSSQ_1 VSSQ_1 VSSQ_1
D7 B9 D7 B9 D7 B9 D7 B9 D7 B9
DQU0 VSSQ_2 DQU0 VSSQ_2 DQU0 VSSQ_2 DQU0 VSSQ_2 DQU0 VSSQ_2
C3 D1 C3 D1 C3 D1 C3 D1 C3 D1
DQU1 VSSQ_3 DQU1 VSSQ_3 DQU1 VSSQ_3 DQU1 VSSQ_3 DQU1 VSSQ_3
C8 D8 C8 D8 C8 D8 C8 D8 C8 D8
DQU2 VSSQ_4 DQU2 VSSQ_4 DQU2 VSSQ_4 DQU2 VSSQ_4 DQU2 VSSQ_4
C2 E2 C2 E2 C2 E2 C2 E2 C2 E2
DQU3 VSSQ_5 DQU3 VSSQ_5 DQU3 VSSQ_5 DQU3 VSSQ_5 DQU3 VSSQ_5
A7 E8 A7 E8 A7 E8 A7 E8 A7 E8
DQU4 VSSQ_6 DQU4 VSSQ_6 DQU4 VSSQ_6 DQU4 VSSQ_6 DQU4 VSSQ_6
A2 F9 A2 F9 A2 F9 A2 F9 A2 F9
DQU5 VSSQ_7 DQU5 VSSQ_7 DQU5 VSSQ_7 DQU5 VSSQ_7 DQU5 VSSQ_7
B8 G1 B8 G1 B8 G1 B8 G1 B8 G1
DQU6 VSSQ_8 DQU6 VSSQ_8 DQU6 VSSQ_8 DQU6 VSSQ_8 DQU6 VSSQ_8
A3 G9 A3 G9 A3 G9 A3 G9 A3 G9
DQU7 VSSQ_9 DQU7 VSSQ_9 DQU7 VSSQ_9 DQU7 VSSQ_9 DQU7 VSSQ_9
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
FULL SCART
SCART AMP
+12V
COMPONENT & AV NOT USE TP(LN52)
EU
AV_CVBS_DET C2817
IC2801 0.1uF
AZ4580MTR-E1 50V
EU
R2861
2.2K OUT1 8 VCC EU
DTV/MNT_L_OUT 1 C2822
EU EU EU 10uF
EU R2866
C2821 R2860 16V
OPT 33K IN1- 7 OUT2 2.2K
10uF R2865 2
16V EU DTV/MNT_R_OUT
470K
R2867
EU IN1+ 6 IN2- 33K OPT
EU R2868 3
10K R2864
C2823 EU 470K
33pF R2869
VEE 5 IN2+ 10K
4
EU
C2824
EU 33pF
R2862 EU
5.6K
SCART1_Lout R2863
EU 5.6K
EU SCART1_Rout
330pF 220K
C2819 R2857
EU EU
R2858 C2820
220K 330pF
CLOSE TO MSTAR
CLOSE TO MSTAR
FULL SCART
+3.3V_Normal
[SCART AUDIO MUTE]
EU
R2808 EU +3.3V_Normal
10K
R2810 DTV/MNT_L_OUT SCART_MUTE +3.5V_ST
1K R2839
SC1/COMP1_DET 2K
SCART_MUTE
SCART_MUTE
Q2802 SCART_MUTE R2844
ESD_SCART MMBT3904(NXP) Q2804 10K
D2808 EU EU MMBT3906(NXP)
5.6V IC2802 C2809
EU MM1756DURE 0.1uF EU SCART1_MUTE
R2801
0 C2811 SCART_MUTE 3 1
DTV/MNT_R_OUT R2840 SCART_MUTE
SC1_SOG_IN 0.1uF
VCC IN 2K C2816
6 1 SCART_MUTE 2
DTV/MNT_VOUT 0.1uF
Q2803
SC1_CVBS_IN MMBT3904(NXP)
EU PS GND
EU 5 2
R2807 C2801
ESD_SCART 47pF
D2827 75 50V
AV_DET ZENER OUT BIAS
4 3
22 ESD_SCART EU
COM_GND D2826
ZENER C2810
21
SYNC_IN 4.7uF
EU
20 R2816
SYNC_OUT 75
19
SYNC_GND2 ESD_SCART
ESD_SCART D2810
18 D2811
SYNC_GND1 20V EU
20V R2815
17 22
RGB_IO
16 SC1_FB
R_OUT EU
15 SC1_R+/COMP1_Pr+ R2811
ESD_SCART
RGB_GND D2812 R2806 75
14 75
20V
R_GND
13
D2B_OUT
12
G_OUT
11 SC1_G+/COMP1_Y+
D2B_IN ESD_SCART R2802
D2813
10 75
G_GND 20V EU
9 R2814
ID 15K
8 SC1_ID
B_OUT
SC1_B+/COMP1_Pb+ ESD_SCART EU
7 ESD_SCART R2817
AUDIO_L_IN D2816
D2814 R2803 20V 3.9K
6 20V 75
B_GND
5
AUDIO_GND EU
4
AUDIO_L_OUT R2812
10K
3 SC1/COMP1_L_IN
AUDIO_R_IN
R2804 EU
2 ESD_SCART
AUDIO_R_OUT 470K R2818
D2815 12K
1 5.6V
EU EU
JK2801 R2813
10K
PSC008-01 SC1/COMP1_R_IN
ESD_SCART EU
D2817 R2805
470K R2819
5.6V
12K
DTV/MNT_L_OUT
OPT
ESD_SCART C2825
D2818 1000pF
5.6V 50V
OPT DTV/MNT_R_OUT
ESD_SCART C2826
D2819 1000pF
5.6V 50V
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
HDMI(REAR 2 Without MHL)
HDMI_1(ARC) HDMI_2
5V_HDMI_1 5V_DET_HDMI_1
5V_HDMI_2 5V_DET_HDMI_2 ESD_HDMI
VA800 R809
ESD_HDMI 10K
D808 R804
10K
R800
R802 1K
1K
C
ESD_HDMI R810
C Q800 B 10K
ESD_HDMI R806 VA802
MMBT3904(NXP) HPD1
D809 Q801 B 10K
MMBT3904(NXP) HPD2
E
JK800 SHIELD
E GND
JK801 SHIELD R814 100
GND DDC_SDA_1
R829 100 20
DDC_SDA_2 R815 100
20 HP_DET DDC_SCL_1
R830 100 19
HP_DET DDC_SCL_2 ESD_HDMI ESD_HDMI
19 5V
ESD_HDMI 18
ESD_HDMI VA803 VA804
18 5V R807
D810 D811 GND R808
17 1.8K 3.3K
GND R803 R801
17 1.8K 3.3K DDC_DATA
16
16 DDC_DATA
HDMI_ARC 15 DDC_CLK
HDMI1_ARC
15 DDC_CLK ESD_HDMI R805
14 NC
D812 0
14 NC
13 CE_REMOTE HDMI_CEC
EAG59023302
13 CE_REMOTE HDMI_CEC
12 CK- D800 ESD_HDMI
EAG59023302
ESD_HDMI_NXP
12 CK- D820 ESD_HDMI RCLAMP0524PA VA806 D800-*1
ESD_HDMI_NXP CK_GND IP4283CZ10-TBA
11
CK_GND RCLAMP0524PA D813 D820-*1
IP4283CZ10-TBA
1 10 CK-_HDMI1
11 CK+ TMDS_CH1- NC_4
1 10 10
1 10
8 D0+
4 7 TMDS_CH2-
4 7
NC_2
7 TMDS_CH2+ NC_1
D0+ D0-_HDMI2 5 6 D0+_HDMI1
5 6
D801 5 6 D2+_HDMI2
TMDS_CH2+
5 6
NC_1
ESD_HDMI_SEMTECH
ESD_HDMI_SEMTECH
R811 MHL_CD_SENSE
100 5V_DET_HDMI_4
HDMI_CEC CEC_REMOTE_S7 /VBUS_EN
AVDD5V_MHL
/MHL_OCP_DET
A2
A1
A2
D804 D803
MMBD6100 MMBD6100
C
DDC_SDA_2 DDC_SDA_1
DDC_SCL_2 DDC_SCL_1
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
L13 Adapter POWER BLOCK
Power_DET PD_+12V --> 3.69V
ADAPTER JACK +24V_LED_DRIVER
PD_+24V_ADAPTER --> 3.81V
+24V_ADAPTER
JK400
KJA-DC-1-0032 L421
UBW2012-121F
4 4
+24V_ADAPTER +12V +3.5V_ST
2 2
R488
100K
PD_+24V_ADAPTER PD_+12V +3.5V_SOC_RESET RESET_IC_SOC_RESET
R494 R450 R402-*1
1 R463
27K 2.7K PWR_DET_ON_SEMI 100 10K
1% 1% IC408
NCP803SN293 RESET_IC_SOC_RESET
R402
VCC RESET 300
3 2 POWER_DET
1
C411 PD_+24V_ADAPTER PD_+12V
R495 R496 GND C474
0.1uF 0.1uF
16V 5.1K 1.2K
1% 1%
R2
R423 +3.3V_Normal +2.5V_Normal
56K IC402
CAP_10uF_X7R
1% TJ1118S-2.5 C403-*1
Vout=0.8*(1+R1/R2)=3.37V 10uF 10V
IN OUT
3
1A 2
1
INV_CTL GND CAP_10uF_X5R C440 OPT
+3.3V_Normal C403 0.1uF D402
10uF 16V 5V
10V
85C
+3.5V_ST
R437 CHANGE TO
OPT +3.5V_ST 1K 10UF/10V/X5R
R461
+24V_ADAPTER -> +12V RL_ON 10K
R446
R493
100
WLED_ENABLE
+12V 10K
C
IC404 R462
R444
10K B
C408 RT8289GSP [EP]GND 10K INV_CTL
0.01uF
50V L407 Q410
E
BOOT SW 4.7uH MMBT3904(NXP)
1 8
THERMAL
NC_1 VIN D401 C432 C434 C445 C449 +3.5V_ST -> +3.3V_Normal
9
D
BLM18PG121SN1D
C436 POWER_ON/OFF_1
0.1uF
16V
C423 C425 C437
G
R434 R438 D405
C401 C406 R1 R415 10K 22K 2.2uF 0.1uF 22uF 5V
10uF 0.1uF 100K 1% PANEL_VCC 10V 16V 10V
+12V
35V 50V
R2
R408 C414
11K 150pF
1% 50V Q409 FET_2.5V_DIODE
L412
AO3407A DMP2130L
UBW2012-121F R445
2.2K Q403-*1
S
D
C443 R443 C
R439 R405 R407
Vout=1.222*(1+R1/R2)=12.33V 33K
10uF
16V
G 5.6K 5.6K 10K B Q400
G
POWER_ON/OFF_1 MMBT3904(NXP)
R440
5.6K
R430 C
EP[GND]
CHANGE TO CHANGE TO +3.5V_ST -> +1.5V_DDR
BST
CAP_10uF_X5R
VIN_3
PWRGD
LX
FB
16V/X5R 10UF/10V/X5R
BOOT
C417
10uF L413 +1.10V_VDDC
EN
CAP_10uF_X7R
10V
12
11
10
16
15
14
13
13
3.6uH
8
IC401 OPT
R417 10uF GND_1 PH_1 22uF 22uF 22uF 0.1uF D404
C419
VIN
TPS65281RGV AGND R414 AP7173-SPG-13 HF(DIODES) 10V 3 IC403 10 C488 10V 10V 10V 16V 2.5V
4.7uF 10V 10K 4.7K TPS54319TRE 3300pF
15
100K
V7V FAULT BLM18PG121SN1D BLM18PG121SN1D 3A
17
3A
8
16
IN OUT
5
USB1_CTL 1 8
AGND
VSENSE
COMP
RT/CLK
EN EN_SW R1 R432
THERMAL
330K
1
COMP
ROSC
RLIM
50V
1/16W 10V 16V 2.5V 15K 3300pF 30K
1/16W 100pF
1% 1%
VCC SS 50V
3 6
R2
R409
2K
R413
C461
R433
10K EN 1.5A5 GND C467
R456
4.7K
R2
1% 16K 4 560pF 1/16W
1% 10uF 1% R441
OPT C410 10V 50V 75K
C426 1/16W
100pF 3300pF 1%
50V 50V
Vout=0.8*(1+R1/R2)=1.5319 Vout=0.827*(1+R1/R2)=1.1578V
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
32inch_Adapter
T6900
L6900
13I-DD01 D6903 BFS3550R2BD8G
SF20D600D2
PATTERN WIDTH 10mm A2
To bo obsolete 1 4 C L6901
+24V_LED_DRIVER A1 BFS3550R2BD8G
42inch_Adapter OPT OPT OPT OPT 3 2
C6900 C6915 C6916 C6917 C6918 C6919 C6924 C6925
470uF 470uF 10uF 10uF 10uF 10uF 1000pF 1000pF 32inch_Adapter 32inch_Adapter 42inch_Adapter
35V 35V 35V 35V 35V 35V 630V 630V OPT
NRA NRA C6907 C6908 C6920 C6910 R6918
33uF 33uF 15uF 0.047uF 470K
42inch_Adapter 160V 160V 250V
T6900-*1 350V 1%
NRA NRA NRA
13I-DD02
1 4 R6919
42inch_Adapter42inch_Adapter 470K
C6907-*1 C6908-*1 1%
3 2 15uF 15uF
250V 250V
R6979 R6978 R6977 R6976 R6975 R6974 R6973 R6938 R6939 R6940 R6941 R6942 R6943 R6944 R6945
150 150 150 150 150 150 150 150 150 150 150 150 150 150 150
32inch_Adapter
R6905-*1 Q6901
10 FDD390N15
D
D6900 42inch_Adapter
1N4148W R6905
22 G
MODEL T6900 Q6902 R6915 R6935 R6911
Q6900 S
MMBT2907ALT1G R6907
32 ROW/POLA E 10K
13I-DD01 FDT86106 51K 0 22K
R6908
R6909
R6936
R6956 R6946
R6957 R6947
R6962 R6952
400mA 32":85V
42 ROW 32inch_Adapter B 42":175V
1
42inch_Adapter
1
13I-DD02 STN4NF20L 75K 0 12K R6903-*1
42inch_Adapter
42inch_Adapter
42inch_Adapter
42inch_Adapter
285mA 47 R6903 C
R6963 R6953
R6964 R6954
R6965 R6955
33
42 POLA
13I-DD02 STN4NF20L 68K->51K 20K 12K
1
300mA 8
42inch_Adapter
42inch_Adapter
42inch_Adapter
42inch_Adapter
42inch_Adapter
42inch_Adapter
LED+
R6966
R6967
R6972
7
1
R6906 5
150 IC6900
MAP3202SIRH
3
R6900
5.1K EN FBN LED-
1 14
WLED_ENABLE 1
R6901
10 VCC FBP 42_ROW_Adapter
2 13 R6915-*1
+12V 32_Adapter/42_POLA_Adapter 75K
P6900
R6915 1%
GATE COMP 51K
3 12 1% PWM_DIM
R6921
GND PWMI 42_POLA_Adapter 1K
4 11
32_Adapter/42_ROW_Adapter R6935-*1
R6935 20K1% R6924
CS OVP 0 15K 32inch_Adapter 42inch_Adapter
5 10 Q6902 Q6902-*1
5%
D6902 FDT86106LZ D STN4NF20L D
R6923 1N4148W
RT PWMO 1K G G
6 9
R6920 S S
SYNC REF 22K
7 8 R6926
100K
R6925
1K
32inch_Adapter
R6911 R6916 R6917 OPT R6927 R6929 R6931 R6933
22K 10K 75K R6922 4.3 4.3 4.3 4.3
1% 1% 1% 1% 1%
1%
42inch_Adapter
R6911-*1
C6901 R6902 C6902 R6904 C6903 12K C6905 C6906 C6909 C6911 C6912 C6913 C6914 R6928 R6930 R6932 R6934
0.1uF 100K 0.47uF 430K 1000pF 1% 1000pF 0.47uF 1000pF 0.01uF 1000pF 1000pF 330pF 3.9 3.9 3.9 3.9
50V 50V 1% 50V 50V 16V 50V 50V 50V 50V 50V 1% 1% 1% 1%
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
MODEL OPTION MODEL OPTION Memory OPTION
PIN NAME PIN NO. LOW HIGH MODEL_OPT_4 MODEL_OPT_6
+2.5V_Normal +3.3V_Normal +2.5V_Normal
MODEL_OPT_DVB_T2(O)
+3.3V_Normal
Memory Note VDDC 1.05V +1.10V_VDDC +1.10V_VDDC
MODEL_OPT_DVB_S(O)
MODEL_OPT_MIU1_1G
MODEL_OPT_MIU0_2G
MODEL_OPT_M120(O)
AB3 FHD HD
1K
1K
1K
1K
1K
1K
1K
1K
1K
VDDC : 2026mA
MODEL_OPT_AJ MODEL_OPT_1 F4 128M 0 0
MODEL_OPT_HD
PHM_OFF PHM_ON
OPT
R290
R291
R222
R221
R206
R208
R211
R226
MODEL_OPT_4 256M 1 0
MODEL_OPT_0 U23 MIU0-128M MIU0-256M
MODEL_OPT_1 256M+128M 1 1 Ginga
R203 100 MODEL_OPT_5 T24 NON_DVB_S DVB_S
RF_SWITCH_CTL MODEL_OPT_2
RF_SW_OPT MODEL_OPT_3 MODEL_OPT_6 B8 MIU1-NO_DDR MIU1-128M
MODEL_OPT_4
MODEL_OPT_5 MODEL_OPT_7 A8 NON_DUAL_STREAM DUAL_STREAM
MODEL_OPT_MIU1_NO_DDR
MODEL_OPT_6 IC101
SYM.E
MODEL_OPT_DVB_T2(X)
MSD804KKX
MODEL_OPT_DVB_S(X)
MODEL_OPT_EU/CHINA
MODEL_OPT_M120(X)
1K
1K
1K
1K
1K
1K
1K
R293
R294
R224
R207
R209
R212
R227
V2 R11
SC1_ID HSYNC1 GND_104
V3 W6 AUDIO OUT R12
SC1_FB VSYNC1 GPIO_PM[13]/GPIO19 MHL_CD_SENSE GND_105
EU EU EU EU EU EU EU
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
LN52_LVDS (EU)
FOR FHD REVERSE(10bit)
Change in S7LR
MIRROR Pol-change
[51Pin LVDS Non-Reverse Connector]
(For FHD 60Hz)
RXA4+ RXA0+ RXA0-
[30Pin LVDS Connector]
RXA4- RXA0- RXA0+
(For HD 60Hz_Normal)
RXA3+ RXA1+ RXA1-
FHD HD
RXA3- RXA1- RXA1+
P1100 P1101
FI-RE51S-HF-J-R1500 RXACK+ RXA2+ RXA2- 10031HR-30
PANEL_POWER
RXACK- RXA2- RXA2+
PANEL_VCC PANEL_POWER
R1109
C1100 0
0.1uF VCOM_SCL V-COM_SCL
R1108
16V 0
VCOM_SDA V-COM_SDA
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
IC102
NAND FLASH MEMORY K9F1G08U0D-SCB0
<CHIP Config(LED_R/BUZZ)>
+3.3V_Normal +3.3V_Normal
Boot from SPI CS1N(EXT_FLASH) 1’b0
S7LR-M_NON_MS10
NC_1
1 48
NC_29 Boot from SPI_CS0N(INT_FLASH) 1’b1
NAND_FLASH_1G_SS IC101
NC_2 EAN61857001 NC_28
2 47 MSD804KKX
NC_3 NC_27 PCM_A[0-7] <CHIP Config>
3 46 PCM_D[0-7]
22 (I2S_OUT_BCK,I2S_OUT_MCK,PAD_PWM1PAD_PWM0)
NC_4
4 45
NC_26
AR101 B51_no_EJ : 4’b0000 Boot from 8051 with SPI flash PCM_D[0] W21 SYM.D
R107 NC_5 I/O7 PCM_A[7] SB51_WOS : 4’b0001 Secure B51 without scramble PCM_D[1] PCMDATA[0]/GPIO129
R109 AA18
1K 3.9K 5 44 SB51_WS : 4’b0010 Secure B51 with scramble PCMDATA[1]/GPIO130
PCM_D[2] AB22
NC_6 I/O6 PCM_A[6] MIPS_SPE_NO_EJ : 4’b0100 Boot from MIPS with SPI flash
AR103 6 43 PCM_D[3] PCMDATA[2]/GPIO131
22 MIPS_SPI_EJ_1 : 4’b0101 Boot from MIPS with SPI flash AE20
R/B I/O5 PCM_A[5] MIPS_SPI_EJ_2 : 4’b0110 Boot from MIPS with SPI flash PCM_D[4] PCMDATA[3]/GPIO123
7 42 AA15
MIPS_WOS : 4’b1001 Secure MIPS without scramble PCM_D[5] PCMDATA[4]/GPIO122
RE I/O4 PCM_A[4] MIPS_WS : 4’b1010 Scerur MIPS with SCRAMBLE AE21
/F_RB 8 41 PCM_D[6] PCMDATA[5]/GPIO121
+3.3V_Normal AB21 AE18
/PF_OE CE NC_25 PCM_D[7] PCMDATA[6]/GPIO120 NF_CE1Z/GPIO141
9 40 Y15 AC17
/PF_CE0 PCM_A[0-14] PCMDATA[7]/GPIO119 NF_WPZ/GPIO196 /PF_WP
NC_7 NC_24 CAP_10uF_X5R AD18
10 39 PCM_A[0] NF_CEZ/GPIO140 /PF_CE0
C102-*1 W20 AC18
OPT NC_8 NC_23 C102 10uF PCM_A[1] PCMADR[0]/GPIO128 NF_CLE/GPIO139 /PF_CE1
1K
1K
1K
1K
1K
R108 V20 AC19
+3.3V_Normal 1K C101 11 38 10V CHANGE TO PCM_A[2] PCMADR[1]/GPIO127 NF_REZ/GPIO142 /PF_OE
0.1uF VCC_1 VCC_2 10UF 10V X5R 10uF 10V W22 AD17
85C
OPT
OPT
OPT
OPT
12 37 CAP_10uF_X7R PCM_A[3] PCMADR[2]/GPIO125 NF_WEZ/GPIO143 /PF_WE
OPT AB18 AE17
R105 VSS_1 VSS_2 C103 PCM_A[4] PCMADR[3]/GPIO124 NF_ALE/GPIO144 PF_ALE
R115
R117
R165
R123
R152
13 36 0.1uF AA20 AD19
1K PCMADR[4]/GPIO102 NF_RBZ/GPIO145 /F_RB
PCM_A[5] AA21
NC_9 NC_22
14 35 PCM_A[6] PCMADR[5]/GPIO104
LED_R/BUZZ Y19
NC_10 NC_21 PCM_A[7] PCMADR[6]/GPIO105
15 34 AB17
AUD_SCK PCM_A[8] PCMADR[7]/GPIO106
CLE NC_20 AUD_MASTER_CLK R148 Y16
16 33 PCM_A[9] PCMADR[8]/GPIO111
AR102 AUD_MASTER_CLK_0 AB19
PCMADR[9]/GPIO113 GPIO_PM[0]/GPIO6
H5
POWER_DET
/PF_CE1 ALE I/O3 PCM_A[3] 56 PCM_A[10] AB20 K6
17 32 OPT
PWM1 PCM_A[11] PCMADR[10]/GPIO117 PM_UART_TX/GPIO_PM[1]/GPIO7 PM_TXD
PF_ALE WE I/O2 PCM_A[2] C112 AA16 K5
18 31 100pF PCM_A[12] PCMADR[11]/GPIO115 GPIO_PM[2]/GPIO8 INV_CTL
/PF_WE PWM0 AA19 J6
WP I/O1 PCM_A[1] 50V PCM_A[13] PCMADR[12]/GPIO107 GPIO_PM[3]/GPIO9 RL_ON
1K
1K
1K
1K
1K
/PF_WP 19 30 AC21 K4
PCM_A[14] PCMADR[13]/GPIO110 GPIO_PM[4]/GPIO10 POWER_ON/OFF_1
AR104 NC_11 I/O0 PCM_A[0] AA17 L6
OPT
22 R106 20 29 PCMADR[14]/GPIO109 PM_UART_RX/GPIO_PM[5]/GPIO11 PM_RXD
C2
1K
NC_12 NC_19 22 PM_SPI_SCZ1/GPIO_PM[6]/GPIO12
R116
R118
R121
R124
R153
21 28 Y20 L5
/PCM_REG PCMREG_N/GPIO126 GPIO_PM[7]/GPIO13 /FLASH_WP
NC_13 NC_18 M6
22 27 GPIO_PM[8]/GPIO14 SIDE_HP_MUTE +3.5V_ST
AB15 M5
R102 /PCM_OE PCMOE_N/GPIO116 GPIO_PM[9]/GPIO15 PANEL_CTL
NC_14 NC_17 AA22 C1
3.3K 23 26 /PCM_WE PM_MODEL_OPT_0
PCMWE_N/GPIO195 PM_SPI_SCZ2/GPIO_PM[10]/GPIO16
NC_15 NC_16 AD22 M4
24 25 /PCM_IORD PCMIORD_N/GPIO114 GPIO_PM[11]/GPIO17 AMP_MUTE
AD20 R180
/PCM_IOWR PCMIOWR_N/GPIO112 4.7K
A2 R147 33
PM_SPI_SCK/GPIO1 SPI_SCK
AD21 D3 R146 33
/PCM_CE PCMCE_N/GPIO118 PM_SPI_CZ0/GPIO_PM[12]/GPIO0 /SPI_CS
AC20 B2
/PCM_IRQA PCMIRQA_N/GPIO108 PM_SPI_SDI/GPIO2 SPI_SDI
Y18 B1 R151 33
/PCM_CD PCMCD_N/GPIO133 PM_SPI_SDO/GPIO3 SPI_SDO
Y21 for SERIAL FLASH
/PCM_WAIT PCMWAIT_N/GPIO103
Y22
PCM_RST PCM_RESET/GPIO132
CI_TS_CLK
Y14
TS0CLK/GPIO90 CI_TS_VAL
NAND_FLASH_1G_HYNIX NAND_FLASH_2G_HYNIX NAND_FLASH_2G_TOSHIBA U21 AA10
NAND_FLASH_1G_THOSIBA USB1_OCD PCM2_CE_N/GPIO134 TS0VALID/GPIO88 CI_TS_SYNC
EAN35669103 EAN61508001 EAN60708702 EAN60991001 V21 Y12
USB1_CTL PCM2_IRQA_N/GPIO135 TS0SYNC/GPIO89 CI_TS_DATA[0-7]
IC102-*1 IC102-*2 IC102-*3 IC102-*4 R20
H27U1G8F2CTR-BC TC58NVG0S3ETA0BBBH H27U2G8F2CTR TC58NVG1S3ETA00 PCM2_CD_N/GPIO138 CI_TS_DATA[0]
T20 Y13 from CI SLOT
PCM_5V_CTL PCM2_WAIT_N/GPIO136 TS0DATA_[0]/GPIO80 CI_TS_DATA[1]
U22 Y11
PCM2_RESET/GPIO137 TS0DATA_[1]/GPIO81 CI_TS_DATA[2]
NC_1 NC_29 NC_1 NC_29 NC_1 NC_29 NC_1 NC_29 AA12
1 48 1 48 1 48 1 48 TS0DATA_[2]/GPIO82 CI_TS_DATA[3]
D4 AB12
NC_2 NC_28 NC_2 NC_28 NC_2 NC_28 NC_2 NC_28 /MHL_OCP_DET UART1_TX/GPIO46 TS0DATA_[3]/GPIO83 CI_TS_DATA[4]
2 47 2 47 2 47 2 47 E4 AA14
MHL_OCP_EN UART1_RX/GPIO47 TS0DATA_[4]/GPIO84 CI_TS_DATA[5]
NC_3 NC_27 NC_3 NC_27 NC_3 NC_27 NC_3 NC_27 N25 AB14
3 46 3 46 3 46 3 46 PM_TXD UART2_TX/GPIO68 TS0DATA_[5]/GPIO85 CI_TS_DATA[6]
N24 AA13
NC_4 NC_26 NC_4 NC_26 NC_4 NC_26 NC_4 NC_26 PM_RXD UART2_RX/GPIO67 TS0DATA_[6]/GPIO86 CI_TS_DATA[7]
4 45 4 45 4 45 4 45 B8 AB11
MODEL_OPT_6 UART3_TX/GPIO50 TS0DATA_[7]/GPIO87
NC_5 I/O7 NC_5 I/O8 NC_5 I/O7 NC_5 I/O8 for SYSTEM EEPROM A8 FE_TS_CLK
5 44 5 44 5 44 5 44 MODEL_OPT_7 UART3_RX/GPIO51
(IC104) AC15 FE_TS_VAL_ERR
NC_6 I/O6 NC_6 I/O7 NC_6 I/O6 NC_6 I/O7 TS1CLK/GPIO101
6 43 6 43 6 43 6 43 R136 22 P23 AD15 FE_TS_SYNC
I2C_SCL I2C_SCKM2/DDCR_CK/GPIO75 TS1VALID/GPI99
R137 22 P24 AC16 FE_TS_DATA[0-7]
R/B I/O5 RY/BY I/O6 R/B I/O5 RY/BY I/O6 I2C_SDA
7 42 7 42 7 42 7 42 I2C_SDAM2/DDCR_DA/GPIO74 TS1SYNC/GPIO100
RE
8 41
I/O4 RE
8
I/O5 RE
8 41
I/O4 RE
8 41
I/O5 D2 AD16 FE_TS_DATA[0] Internal demod out
41 RGB_DDC_SDA DDCA_DA/UART0_TX TS1DATA_[0]/GPIO91 FE_TS_DATA[1]
CE NC_25 CE NC_25 CE NC_25 CE NC_25 D1 AE15
9 40 9 40 9 40 9 40 RGB_DDC_SCL DDCA_CK/UART0_RX TS1DATA_[1]/GPIO92 FE_TS_DATA[2]
AE14
NC_7 NC_24 NC_7 NC_24 NC_7 NC_24 NC_7 NC_24 TS1DATA_[2]/GPIO93 FE_TS_DATA[3] FE_TS_DATA[0]
10 39 10 39 10 39 10 39 AC13
TS1DATA_[3]/GPIO94 FE_TS_DATA[4] FE_TS_DATA[0]
NC_8 NC_23 NC_8 NC_23 NC_8 NC_23 NC_8 NC_23 P21 AC14
11 38 11 38 11 38 11 38 PWM0 PWM0/GPIO69 TS1DATA_[4]/GPIO95 FE_TS_DATA[5]
N23 AD12
VCC_1 VCC_2 VCC_1 VCC_2 VCC_1 VCC_2 VCC_1 VCC_2 PWM1 PWM1/GPIO70 TS1DATA_[5]/GPIO96 FE_TS_DATA[6]
12 37 12 37 12 37 12 37 P22 AD13
PWM2 PWM2/GPIO71 TS1DATA_[6]/GPIO97 FE_TS_DATA[7]
VSS_1 VSS_2 VSS_1 VSS_2 VSS_1 VSS_2 VSS_1 VSS_2 R21 AD14
13 36 13 36 13 36 13 36 PWM3/GPIO72 TS1DATA_[7]/GPIO98
IC101-*1 P20
NC_9 NC_22 NC_9 NC_22 NC_9 NC_22 NC_9 NC_22 PWM4/GPIO73
14 35 14 35 14 35 14 35 LGE2121-MS (M1_L13_MS10) F6
LED_R/BUZZ PWM_PM/GPIO197
NC_10 NC_21 NC_10 NC_21 NC_10 NC_21 NC_10 NC_21
15 34 15 34 15 34 15 34
CLE NC_20 CLE NC_20 CLE NC_20 CLE NC_20 S7LR-M_MS10
16 33 16 33 16 33 16 33 H6
C7 AB25 KEY1 SAR0/GPIO34
ALE I/O3 ALE I/O4 ALE I/O3 ALE I/O4 GPIO39 LVA0P G5
17 32 17 32 17 32 17 32 E6 AB23 KEY2 SAR1/GPIO35
GPIO40 LVA0N G4
WE I/O2 WE I/O3 WE I/O2 WE I/O3 F5 AC25 SAR2/GPIO36
18 31 18 31 18 31 18 31 GPIO41 LVA1P J5
B6 AB24 SAR3/GPIO37
WP I/O1 WP I/O2 WP I/O1 WP I/O2 GPIO42 LVA1N R164 1K J4
19 30 19 30 19 30 19 30 E5 AD25 SCART1_MUTE SAR4/GPIO38
GPIO43 LVA2P EU
NC_11 I/O0 NC_11 I/O1 NC_11 I/O0 NC_11 I/O1 D5 AC24
20 29 20 29 20 29 20 29 GPIO44 LVA2N
B7 AE23
NC_12 NC_19 NC_12 NC_19 NC_12 NC_19 NC_12 NC_19 GPIO45 LVA3P R23
21 28 21 28 21 28 21 28 E7 AC23 VSYNC_LIKE/GPIO146
GPIO48 LVA3N
NC_13 NC_18 NC_13 NC_18 NC_13 NC_18 NC_13 NC_18 F7 AC22
22 27 22 27 22 27 22 27 GPIO49 LVA4P R24
AB5 AD23 V-COM_SCL V-COM_SCL SPI1_CK/GPIO199
NC_14 NC_17 NC_14 NC_17 NC_14 NC_17 NC_14 NC_17 GPIO52 LVA4N R25
23 26 23 26 23 26 23 26 AB3 V-COM_SDA V-COM_SDA SPI1_DI/GPIO200
GPIO53 T21
NC_15 NC_16 NC_15 NC_16 NC_15 NC_16 NC_15 NC_16 A9 V23 SENSOR_SCL SENSOR_SCL SPI2_CK/GPIO201
24 25 24 25 24 25 24 25 GPIO54 LVB0P T22
F4 U24 SENSOR_SDA SENSOR_SDA SPI2_DI/GPIO202
GPIO55 LVB0N
AB1 V25
I2C_SCKM0/GPIO56 LVB1P
N6 V24
I2C_SDAM0/GPIO57 LVB1N
AB2 W25
GPIO76 LVB2P
AC2 W23
GPIO77 LVB2N
AA23
LVB3P
Y24
DIMMING I2C +3.3V_Normal LVB3N
LVB4P
AA25
AA24
LVB4N S7LR-M_NON_MS10
OPT AE24 IC101
R156 10K LVACLKP MSD804KKX
PWM0 AD24
LVACLKN
R140 R141 R144 R145 Y23
1K 1K 2.2K 2.2K LVBCLKP
R157
PWM_DIM
100
PWM2 LVBCLKN
W24
C7
SYM.A AB25
OPT AMP_RESET GPIO39 LVA0P RXA0+
T25 E6 AB23
C111 AMP_SDA GPIO194 FRC_RESET GPIO40 LVA0N RXA0-
2.2uF U23 F5 AC25
AMP_SCL GPIO191 5V_DET_HDMI_2 GPIO41 LVA1P RXA1+
T24 B6 AB24
GPIO192 5V_DET_HDMI_4 GPIO42 LVA1N RXA1-
I2C_SDA T23 E5 AD25
GPIO193 AV_CVBS_DET GPIO43 LVA2P RXA2+
I2C_SCL D5 AC24
AV2_CVBS_DET GPIO44 LVA2N RXA2-
B7 AE23
SC1/COMP1_DET GPIO45 LVA3P RXA3+
E7 AC23
HP_DET GPIO48 LVA3N RXA3-
F7 AC22
S2_RESET GPIO49 LVA4P RXA4+
AB5 AD23
TUNER_RESET GPIO52 LVA4N RXA4-
AB3
MODEL_OPT_0 GPIO53
A9 V23
5V_DET_HDMI_1 GPIO54 LVB0P RXB0+
EEPROM +3.3V_Normal MODEL_OPT_1
F4
GPIO55 LVB0N
U24
RXB0-
PM MODEL OPTION LNA_CTRL_1
AB1
N6
I2C_SCKM0/GPIO56 LVB1P
V25
V24
RXB1+
LNA_CTRL_2 I2C_SDAM0/GPIO57 LVB1N RXB1-
AB2 W25
PM_MODEL_OPT_0 MODEL_OPT_2 GPIO76 LVB2P RXB2+
IC104 +3.5V_ST AC2 W23
BR_RESET_DEMOD GPIO77 LVB2N RXB2-
M24256-BRMN6TP C105 HIGH : HD_NON_EU AA23
LVB3P RXB3+
NVRAM_ST 0.1uF
NVRAM_RENESAS
LOW : HD_EU Y24
LVB3N RXB3-
HD_LVDS_pattern is different. FRC_RESET AA25
IC104-*1 R174 R177 AV2_CVBS_DET LVB4P RXB4+
E0 VCC R1EX24256BSAS0A 10K 10K Between EU and NON_EU LVB4N
AA24
RXB4-
1 8 5V_DET_HDMI_1
MODEL_OPT_TW HD_LVDS_NON_EU
E1 WC
PM_MODEL_OPT_1 AE24
RXACK+
2 7 A0 VCC PM_MODEL_OPT_0 LVACLKP
1 8 HIGH : TAIWAN AD24
RXACK-
A0’h LOW : EU,AJ
LVACLKN
Y23
E2 SCL PM_MODEL_OPT_1 LVBCLKP RXBCK+
3 6 R111 22 I2C_SCL A1 WP
2 7 W24
NC : Other LVBCLKN RXBCK-
VSS
4 5
SDA
R112 22 A2 SCL
R175 R176 for 1 Binary
I2C_SDA 3 6 10K 10K T25
MODEL_OPT_EU/AJ HD_LVDS_EU GPIO194 MODEL_OPT_3
C104 C106 U23
8pF 8pF VSS SDA GPIO191 MODEL_OPT_4
4 5 T24
EAN61548301 OPT OPT GPIO192 MODEL_OPT_5
T23
GPIO193 MODEL_OPT_8
EAN62389501
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Close to the tuner
NETCAST4.0_EU_TUNER_BLOCK
This was being applied to the only china demod,
+3.3V_TU so this has to be deleted in both main and ISDB sheet.
IF_AGC_SEL
IC2603
AP1117E18G-13 LNA2_CTL
+1.8V_TU
R2614
R2611 100K R2632
100 1
TUNER_RESET
C2622
0.1uF
16V
C2641 C2642
TU_I2C_FILTER
R2609-*1 Vo=VREF*(1+R2/R1) 0.1uF 10uF
MLG1005SR27JT 16V 10V
NC_1 OPT
+3.3V_TU VREF=1.25V
1 C2653
20pF TU_I2C_FILTER
R2610-*1
RESET 50V MLG1005SR27JT
2
R2870 R2871
1K 1K
SCL TU_I2C_NON_FILTER
R2609 33
3 TU_SCL
C2607 C2651
SDA 20pF TU_I2C_NON_FILTER 20pF
4 50V R2610 33 50V +3.3V_TU
TU_SDA
C2612 C2652
3.3V 20pF
50V
20pF
50V
5
C2621 C2623
NC_2 100pF 0.1uF
6 50V 16V
1.8V +1.8V_TU
7
C2602 C2604
100pF 0.1uF +3.3V_TU +3.3V_Normal
NC_3 50V 16V
8
IF_AGC L2606
9 IF_AGC_MAIN UBW2012-121F
12
SHIELD
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Standard Repair Process
Established
Error A. Video error date 2013. 01 .09
LCD TV symptom
No video/ Normal audio Revised date 1/14
First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D, LVDS Cable, Speaker Cable, IR B/D Cable,,,)
☞A1 ☞A4
No video Normal Y Check Back Light Y Check DC24V from Normal Y Replace T-con Board
On
Normal audio audio On with naked eye Adapter voltage or module
N N
☞A2 N
Check Power Board 85~175VV output
Move to No Repair Power
video/No audio Board or parts
Normal Y
Replace module
voltage
N End
Repair Power
Board or parts
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
1 / 36
Standard Repair Process
Established
Error A. Video error date 2013. 01 .09
LCD TV symptom
No video/ No audio Revised date 2/14
☞A4
Y Check and
No Video/ Check DC24V from Normal
replace
No audio Adapter voltage?
MAIN B/D
N End
Replace Power
Board and repair
parts
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
2 / 36
Standard Repair Process
Established
Error A. Video error date 2013. 01 .09
LCD TV symptom
Picture broken/ Freezing Revised date 3/14
Check RF Cable ☞ A6
Normal Y Check SVC N Check Y
Connection Normal Close
1. Reconnection Picture? S/W Version Bulletin? Tuner soldering Picture?
2. Install Booster
Y N
N
S/W Upgrade
Normal N Contact with signal distributor Replace
Picture? or broadcaster (Cable or Air) Main B/D
N
Normal
Y Picture?
Y
Close
Close
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
3 / 36
Standard Repair Process
Established
Error A. Video error date 2013. 01 .09
LCD TV symptom
Tuning fail, Picture broken/ Freezing Revised date 4/14
Contact with
Change satellite setting N
signal distributor Normal
(match with installed ANT)
or broadcaster Picture?
(Cable or Air)
Y
N
Normal
Picture?
Close
Close
Y
Close
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
4 / 36
Standard Repair Process
Established
Error A. Video error date 2013. 01 .09
LCD TV symptom
Color error Revised date 5/14
☞ A8/ A9
☞A7 ※ Check and
replace Link
Check color by input Y Y Y
Color Cable Color Color
-External Input Replace Main B/D Replace module
error? (LVDS) and error? error?
-HDMI/DVI
contact
N condition N N
☞A10 Check
External device Y
External Input external
Check Test pattern /Cable Replace Main B/D
error device and
normal
cable
N
Request repair
for external
device/cable
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
5 / 36
Standard Repair Process
☞A7 ☞ A8/ A9 N
Check external
Check color condition by input Check and N
Screen Y device Y Screen Screen
-External Input Normal? replace Link Replace Main B/D
normal? connection normal? normal?
-HDMI Cable
condition
N N Y Y
S/W Upgrade
Request repair for
external device
Normal N
screen?
End
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
6 / 36
Standard Repair Process
Established
Error B. Power error date 2013. 01 .09
LCD TV symptom
No power Revised date 7/14
☞A11 ☞A13
DC Power on
Check Power LED Y Normal N Check Power Y Replace
by pressing Power Key OK?
Power LED On? operation? On ‘”High” Adapter
On Remote control
. Stand-By : Red N Y
Check Power cord
Replace Main B/D
was inserted properly
☞A4
N Measure DC 24V from Adapter
Normal?
Y
Y Y
※
☞A12
Normal
voltage?
Replace Main B/D
Close Normal
Check ST-BY 3.5V
voltage? N
N Replace Adapter
Replace Adapter
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
7 / 36
Standard Repair Process
Established
Error B. Power error date 2013. 01 .09
LCD TV symptom
Off when on, off while viewing, power auto on/off Revised date 8/14
Check outlet
☞A14
N Check Power Off CPU Y
Check A/C cord Error? Replace Main B/D Normal? End
Mode Abnormal
Y N
Check for all 3- phase
power out Abnormal Replace Adapter
1
* Please refer to the all cases which Status Power off List Explanation
"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL
can be displayed on power off mode.
"POWEROFF_OFFTIMER" Power off by OFF TIMER
"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER
"POWEROFF_INSTOP" Power off by INSTOP KEY
Normal "POWEROFF_AUTOOFF" Power off by AUTO OFF
"POWEROFF_ONTIMER" Power off by ON TIMER
"POWEROFF_RS232C" Power off by RS232C
"POWEROFF_SWDOWN" Power off by S/W Download
"POWEROFF_UNKNOWN" Power off by unknown status except listed case
"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble
Abnormal
"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
8 / 36
Standard Repair Process
Established
Error C. Audio error date 2013. 01 .09
LCD TV symptom
No audio/ Normal video Revised date 9/14
☞A15 ☞A4
Check user N Y
No audio Check DC24V from Normal
menu > Off
Screen normal Adapter voltage
Speaker off
Y N
Check Speaker N
Disconnection Replace Main B/D End
disconnection
Replace Speaker
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
9 / 36
Standard Repair Process
Established
Error C. Audio error date 2013. 01 .09
LCD TV symptom
Wrecked audio/ discontinuation/noise Revised date 10/14
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
10 / 36
Standard Repair Process
Replace
Main B/D
☞A16 ☞A16
☞A16
Check & Repair N Y Y
Check R/C itself Normal Y Normal Check B+ 3.5V Normal Check IR Normal
operating? Cable connection operating? Voltage? Signal?
Operation On Main B/D Output signal
Connector solder
N
Y N N
☞A4
Check R/C Operating Check & Replace Check 3.5V on Main B/D Repair/Replace
When turn off light Baterry of R/C Close
Replace Adapter or IR B/D
in room Replace Main B/D
(Adapter don’t have problem)
If R/C operate, Normal
operating? Close
Explain the customer
cause is interference
from light in room. N
Replace R/C
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
11 / 36
Standard Repair Process
Established
Error D. Function error date 2013. 01 .09
LCD TV symptom
External device recognition error Revised date 12/14
Check technical
Check Y
Signal information Technical N External Input
input Replace Main B/D
input? - Fix information information? Recognition error
signal
- S/W Version
N Y
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
12 / 36
Standard Repair Process
Established
Error E. Noise date 2013. 01 .09
LCD TV symptom
Circuit noise, mechanical noise Revised date 13/14
Identify Check
Circuit
nose location of Replace Main B/D
noise
type noise
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
13 / 36
Standard Repair Process
Established
Error F. Exterior defect date 2013. 01 .09
LCD TV symptom
Exterior defect Revised date 14/14
Cabinet
Replace cabinet
damage
Remote
controller Replace remote controller
damage
Stand
Replace stand
dent
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
14 / 36
Contents of LCD TV Standard Repair Process Detail Technical Manual
No. Error symptom Content Page Remarks
1 Check LCD back light with naked eye A1
2 LED driver B+ measuring method A2
A. Video error_ No video/Normal audio
3 Check White Balance value A3
4 Power Board voltage measuring method A4
6 TUNER input signal strength checking method A5
A. Video error_ No video/Video lag/stop
7 LCD-TV Version checking method A6
9
LCD TV connection diagram A7
10
A. Video error_Color error Check Link Cable (LVDS) reconnection A8
11
condition A9
12 Adjustment Test pattern - ADJ Key A10
13 LCD TV connection diagram A8
A. Video error_Vertical/Horizontal bar, Check Link Cable (LVDS) reconnection A8
14
residual image, light spot condition A9
15 Adjustment Test pattern - ADJ Key A10
16 Exchange T-Con Board (1) A-1/5
Copyright © 2013 LG Electronics. Inc. All rights reserved. Continue to the next
LGEpage
Internal Use Only
Only for training and service purposes
15 / 36
Contents of LCD TV Standard Repair Process Detail Technical Manual
Continued from previous page
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
16 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
2013. 01 .09
LCD TV Revised
Content Check Back Light On with naked eye date A1
<ALL MODELS>
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
17 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
2013. 01 .09
LCD TV Revised
Content Inverter B+ 24V measuring method date A2
<ALL MODELS>
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
18 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
2013. 01 .09
LCD TV Revised
Content Check White Balance value date A3
<ALL MODELS>
Entry method
3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re-
enter the value after replacing the MAIN BOARD.
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
19 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/ Audio date
2013. 01 .09
LCD TV Revised
Content Power Board voltage measuring method date A4
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
20 / 36
Standard Repair Process Detail Technical Manual
Error Established
A. Video error_Video error, video lag/stop 2013. 01 .09
symptom date
LCD TV Revised
Content TUNER input signal strength checking method A5
date
<ALL MODELS>
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
21 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_Video error, video lag/stop date
2013. 01 .09
LCD TV Revised
Content LCD-TV Version checking method A6
date
Version
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
22 / 36
Standard Repair Process Detail Technical Manual
Error A. Video error _Vertical/Horizontal bar, residual Established 2013. 01 .09
symptom image, light spot date
LCD TV Revised
Content LCD TV connection diagram (1) date A7
<ALL MODELS>
<ALL MODELS>
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
24 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom
A. Video error_Color error 2013. 01 .09
LCD TV date
Adjustment Test pattern - ADJ Key Revised
Content date A10
Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)
4.Video error (Classification of MODULE or Main-B/D!)
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
25 / 36
Appendix : Exchange T-Con Board (1)
Solder defect, CNT Broken Solder defect, CNT Broken Solder defect, CNT Broken
Solder defect, Short/Crack Fuse Open, Abnormal power section Abnormal Display
No picture/Sound Ok
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
28 / 36
Appendix : Exchange the Module (1)
Panel Mura, Light leakage Panel Mura, Light leakage Press damage
Un-repairable Cases
In this case please exchange the module.
Press damage
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
29 / 36
Appendix : Exchange the Module (2)
Un-repairable Cases
In this case please exchange the module.
Horizontal Block
Gate TAB IC Defect
Gate TAB IC Defect
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
30 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _No power date
2013. 01 .09
LCD TV Revised
Content Check front display LED date A11
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
31 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _No power date
2013. 01 .09
LCD TV Revised
Content Check power input voltage and ST-BY 3.5V A12
date
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
32 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _No power date
2013. 01 .09
LCD TV Revised
Content Checking method when power is ON date A13
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
33 / 36
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _Off when on, off whiling viewing date
2013. 01 .09
LCD TV Revised
Content POWER OFF MODE checking method date A14
<ALL MODELS>
Entry method
<ALL MODELS>
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
35 / 36
Standard Repair Process Detail Technical Manual
Error D. Function error_ No response in remote controller, Established 2013. 01 .09
symptom key error date
LCD TV Revised
Content Remote controller operation checking method date A16
<ALL MODELS>
P600
1 GND
2 KEY1
3 KEY2
4 3.5V_ST
5 GND
6 LED_R
③ 7 IR
① 8 GND
①
②
Checking order
1. Check IR cable condition between IR & Main board.
2. Check the st-by 3.5V on the terminal 4.
3. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog
Tester needle moves slowly, and defective when it does not move at all.
Copyright © 2013 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
36 / 36