Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
7.1
1. W hat is t he colour of a dry powder ext inguisher?
a)Green
b)Red
c)Blue
2. W hat is t he mixt ure of acet ylene gas f orms an explosive component wit h?
a)T in and S ilver
b)T in and Copper
c)Copper and S ilver
4. Neit her oil nor grease should be used as a lubricant on coupling or pipeline carrying…
a)Oxygen
b)Kerosene
c)Nit rogen
5. W hat is t he shape of mandat ory sign, wit h t he symbol is diagonal crossed sign?
a)Round
b)T riangle
c)S quare
7. W hat t ype of grinding wheel would you sharpen an High S peed S t eel(HS S ) drill bit on?
a)Green wheel
b)Course wheel
c)F ine W heel
7.2
1. W hat do you need f or measuring and marking out ?
a)V ernier Caliper, divider, st eel rule, scriber, f it t er square and cent re punch
b)Vernier Caliper, divider, st eel rule, plier, scriber, long nose and cent re punch
c)Vernier Caliper, st eel rule, f it t er square, cut t er, rivet ing grip and cent re punch
2. How many t imes do you carry out corrosion prot ect ion when you are at t ached t o
workshop?
a) Once a mont h, if necessary
b) Once a week or whenever necessary
c) Never at all
3. W hat do you call t he dif f erence bet ween t he maximum and minimum sizes?
a)Clearance
b)T olerance
c)A llowance
5. W hich are t he equipment s t hat mandat ory t o meet t he manuf act urer specif icat ion f or
calibrat ion?
a)Vernier Caliper, Micromet er, V-block, dept gauge, t orque wrench and surf ace
plat e
b)Vernier caliper, micromet er, st eel rule, V-block, Dept gauge, surf ace plat e and
t hread gauge.
c)V ernier caliper, micromet er, Dept gauge, t orque wrench, height gauge and
dial t est indicat or
6. W hat is t he f ollowing inf ormat ion, if an equipment once calibrat ed on a calibrat ion
st icker?
a)Part Number and serial number of t hat equipment , dat e of calibrat ion and t he
next due dat e, signat ure or t he name of t he personnel.
b)Part number and serial number of t he equipment , dat e of calibrat ion and t he next
due dat e, signat ure or approval number st amp of cert if ying personnel
c)Part number and serial number of t he equipment , dat e of calibrat ion and t he next
due dat e, st amp of cert if ying personnel.
7. How much calibrat ion records or cert if icat e should cont ain t he f ollowing inf ormat ion f or
each appliance calibrat ed?
a)Minimum
b)Maximum
c)Non
7.3
1. How many t ypes of mat erials used f or surf ace plat e?
a)Cast iron, mild st eel
b)Cast iron, st ainless st eel
c)Cast iron, granit e
13. A spring loaded rat chet at t ached t o t he spindle of a st andard ext ernal micromet er
produce…
a)A pre- set during use
b)Means f or cont rolling t hread binding
c)A smoot h f ree run during use
7.5
1. T his symbol f ound on an engineering drawing would mean:
a)Cylindricit y
b)A ngularit y
c)Concent ricit y
3. W hich pict orial proj ect ion shows one f ace in t he elevat ion and line of dept normally
draw at 30° or 45° t o t he horizont al?
a)Oblige
b)Perspect ive
c)I somet ric
7. 6
1. W hich of t he f ollowing shaf t would you use t o obt ain a clearance f it in a bush 0.750 inch
diamet er?
a. 0.752 inch
b. 0. 748 inch
c. 0.750 inch
3. I f t here is a posit ive allowance bet ween t he smallest possible hole and t he largest
shaf t , t he f it is
a. some sort of a driving f orce
b. t he shaf t t o be shrunk by cooling
c. t he hole t o be expanded by heat
4. W hat is t he f irst size drill in pract ice t o drill a hole t o prevent misalignment ?
a. No. 40 drill bit
b. No 30 drill bit
c. ⅛ inch drill bit
7. I n st raight Edge and F eeler Gauge t o calculat e t he amount of bow t o cont rol rods used
f ormula of
a. Bow = Dist ance wit h member and st raight edge divided by Lengt h of member
under t est
b. Bow = Dist ance wit h member and st raight edge divided by Lengt h of member
under t est
c. Bow = T he amount of dist ance mult iply t he st raight edge divided by Lengt h of
member under t est
7.8
1. W hat is a normal spacing bet ween rivet s?
a. 2D
b. 3D
c. 4D
2. I f t he t hickness of a single sheet of mat erial about t o be j oined of rivet ing was 1/ 16 of
an inch t hick, what would be t he appropriat e diamet er of t he rivet t o be used?
a. 1/ 16 inch
b. 3/ 16 inch
c. 1/ 8 inch
4. Rivet allowance is
a. t he dist ance t he rivet is posit ioned f rom t he edge of t he repair plat e
b. t he amount of mat erial required t o f orm t he rivet on inst allat ion
c. t he dist ance bet ween rivet s in t he same row
5. Rivet clearance is
a. T he dist ance bet ween rivet s in t he same row
b. t he amount t hat t he rivet hole diamet er exceeds t he rivet diamet er
c. t he dist ance bet ween rows of rivet s
7. T he ‘grip’ of rivet is
a. t he lengt h of rivet lef t t o f orm t he head
b. t he t hickness of plat es which can be f ast ened
c. t he area of t he plat es held f irmly t oget her
7.9
1. T he ‘lay line’ on a f lexible hose is
a. an arrow paint ed on t he hose t o show t he direct ion of t he f luid f low
b. W hit e line paint ed t he f ull st rengt h of t he hose t o indicat e any t wist in
t he hose
c. W hit e line paint ed t he f ull st rengt h of t he hose t o indicat e any st ret ch in t he
hose.
5. W hat is t he t orque value f or t ight ening t ube nut s f or 5/ 16 inch st eel t ubes
a. 50-90 inch pounds
b. 70- 120 inch pounds
c. 90-120 inch pounds
6. W hat is t he t orque value f or t ight ening t ube nut s f or 5/ 16 inch aluminium alloy t ubes
a. 40-65 inch pounds
b. 50-70 inch pounds
c. 60- 80 inch pounds
7.10
1. S pring are manuf act ured f rom
a. high carbon alloy st eel wit h high st rengt h requirement s
b. low carbon alloy st eel wit h high st rengt h requirement s
c. high carbon alloy st eel wit h low st rengt h requirement s
4. Ball and roller bearings are made f rom a combinat ion of low carbon st eel and a
percent age of
a. Chromium
b. Nickel
c. Nickel Chrome
5. On inspect ion of a bearing is f ound t o have dist ort ion. W hat act ion should be t aken?
a. Rej ect bearing
b. No act ion required. S ome dist ort ion is normal
c. Blend out dist ort ion and re-grease bearing
6. W hen a bearing has 2 point s and t he inner ring and out er ring is inst alled
a. Neit her of t he pract ices are allowed
b. T he inner ring can be removed f rom it s inner shaf t f or cleaning
c. T he out er ring can be removed f rom it s housing f or inspect ion
7.12
1. I f cont rol chain can be lif t ed clear of a t oot h, it should be
a. Rej ect ed as unserviceable
b. Removed and an elongat ion check carry out
c. Clean, re-t ensioned and inspect ed af t er a period of t ime
2. A cont rol cable t hat has been cont aminat ed wit h acid should be…
A ) Clean
B) Clean, inspect ed and reinspect ed af t er period of t ime
C) Rej ect ed
2. W hen t he peace of met al is bent , t he surf ace of t he met al on t he out side of t he bent
is..
A ) I n compression
B) Neit her in t ension or compression
C) I n t ension
4. A new dest ruct ive t est ing t echnique which is suit able f or inspect ion f or delaminat ion in
Redux bonded st ruct ure of light aluminium alloy is?
A ) Ult rasonic
B) S t eady current
C) Magnet ic f low
5. W hat solvent s could you use t o clean t oils used f or f iberglass repair?
A ) T richloroet hylene or acet one
B) Lead f ree pet rol / kerosene
C) A cet one or MEK
22. During a colour cont rast t est penet rant t ime should be
A ) Longer f or a small crack.
B) S hort er f or a small crack.
C) Longer f or a wide crack.
25. W hich of t hese met als is inspect ed using t he magnet ic part icle inspect ion met hod?
A ) Magnesium alloy.
B) A luminium alloy.
C) I ron alloy.
27. W hich of t he f ollowing NDT t echniques cannot be used on a component manuf act ured
f rom aust enit ic st ainless st eel?
A ) Magnet ic – part icle.
B) Penet rant dye.
C) Hot oil and chalk
28. I f an applicat ion of developer it all t urns t o a pinkish hue, what has happened?
A ) T hin porosit y
B) T he hue has pinked
C) I ncorrect cleaning
29. I f dye penet rant inspect ion indicat ions are nit sharp and clear, t he most probable
cause t hat t he part
A ) is not damaged.
B) was not correct ly degaussed bef ore t he developer was applied
C) was not t horoughly cleaned bef ore developer was applied
32. T he eddy current met hod of f law det ect ion can det ect
A ) S ub surf ace f laws only
B) S urf aces f laws and t hose j ust beneat h t he surf aces
C) S urf ace f laws only
33. W hat act ion is t aken wit h a common circlip removed f rom a component ?
A ) I t is replaced wit h a new it em on assembly
B) I t is checked f or springness
C) I t is examined f or dist ort ion
36. W hat t ype of repair has t o be used where t he damage is large and lost st rengt h of
area has t o be rest ored?
A ) F illing plat e and pat ch
B) Pat ch repair t o t he punct ured skin
C) I nsert and but t st rap
7. 19 A BNORMA L EV ENT
1. A n aircraf t wit h underwing mount ed engines has a heavy landing, where would you expect
t o see wrinkling on t he skins?
A ) Bot t om skin caused by engines inert ia
B) T op skin only
C) On t he t op and bot t om skins
3. W hat is t he reason f or a primary bonding connect ion’s large cross-sect ional area?
A ) T o carry t he st at ic discharge current t o t he conduct ing nose wheel
B) T o carry light ening discharge current should t he need arise
C) T o maint ain t he airf rame at t he same pot ent ial t hroughout
5. On an aircraf t which has had a heavy landing, on t he lower wing you may see
A ) S agging
B) Hogging
C) W rinkling