Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
===========================================================================
7201.10.00 PIG IRON, comprising ALL of the following:
(a) carbon, with a composition less than 5%;
(b) sulphur;
(c) silicon;
(d) phosphorus;
(e) manganese
Op. 02.11.1999 Dec. 07.01.2000 - TC 9908323
7210.49.00 STEEL, COIL, hot dip zinc coated, complying with Japanese
Industrial Standard JIS G 3302:2007, having ALL of the following:
(a) yield strength NOT less than 275 N/mm2 and NOT greater
than 380 N/mm2;
(b) tensile strength NOT less than 440 N/mm2;
(c) elongation NOT less than 29% and NOT greater than 41%;
(d) coating mass NOT less than 45 g/m2 and NOT greater than
65 g/m2;
(e) thickness NOT less than 1.14 mm and NOT greater than 1.26
mm;
(f) width NOT less than 1 590 mm and NOT greater than 1 605 mm
Op. 21.10.2009 Dec. 08.01.2010 - TC 0939596
7210.50.00 TIN FREE STEEL, flat rolled, in coils, chromium plated, having
ALL of the following:
(a) width NOT less than 750 mm and NOT greater than 1 000 mm;
(b) thickness NOT greater 0.30 mm;
(c) temper designation of 61 to 76 (both inclusive) in
accordance with Rockwell hardness 30 T range
Op. 26.11.2009 Dec. 26.02.2010 - TC 0944971
7210.50.00 TIN FREE STEEL, flat rolled, in coils, chromium plated, having ALL
of the following:
(a) width of 830 mm or greater but NOT exceeding 850 mm;
(b) thickness NOT exceeding 0.18 mm;
(c) temper designation of 70-76 (both inclusive) in
accordance with Rockwell hardness 30 T range
Op. 14.12.2001 Dec. 08.03.2002 - TC 0111311
7210.70.00 STEEL, TIN FREE, laminated on one side with polypropylene and on
the other side with polyethylene terephthalate
Op. 26.06.1998 Dec. 11.09.1998 - TC 9805588
7210.90.00 CERAMIC STEEL, being two layers of enamel fused onto high grade
steel
Op. 14.11.1994 Dec. 07.03.1995 - TC 9408919
7211.29.00 STEEL STRIP, cold rolled, in coil form, having ALL of the
following:
(a) chemical composition by percentage of weight in
accordance with EITHER of the compositions listed in
THE TABLE;
(b) dimensions, being ANY of the following width and
thickness combinations:
(i) 26 mm width (25.91/26.42 mm) x 4 mm thickness
(3.90/4.12 mm);
(ii) 26 mm width (25.91/26.42 mm) x 4.5 mm thickness
(4.49/4.71mm);
(iii) 39 mm width (38.61/39.12 mm) x 4 mm thickness
(3.56/3.80 mm);
(iv) 39 mm width (38.61/39.12 mm) x 5 mm thickness
(4.83/5.09 mm),
(c) camber tolerance in accordance with British Standard
1449 (BS1449) Part 1, Table 30
THE TABLE
COMPOSITION 1
CARBON (C) NOT less than 0.37 and NOT greater than 0.44;
MANGANESE (Mn) NOT less than 0.70 and NOT greater than 1.00;
SILICON (Si) NOT less than 0.17 and NOT greater than 0.37;
SULPHUR (S) NOT greater than 0.035;
PHOSPHOROUS (P) NOT greater than 0.035;
CHROMIUM (Cr) NOT greater than 0.25;
NICKEL (Ni) less than 0.30;
COPPER (Cu) NOT greater than 0.25
COMPOSITION 2
CARBON (C) NOT less than 0.42 and NOT greater than 0.50;
MANGANESE (Mn) NOT less than 0.50 and NOT greater than 0.80;
SILICON (Si) NOT less than 0.17 and NOT greater than 0.37;
SULPHUR (S) less than 0.035;
PHOSPHOROUS (P) less than 0.035;
CHROMIUM (Cr) less than 0.25;
NICKEL (Ni) less than 0.30;
COPPER (Cu) less than 0.25
Op. 09.02.2010 Dec. 30.04.2010 - TC 1007032
7211.29.00 STRIP, STEEL, ANNEALED, fully spheroidized (NOT less than 95%),
cold rolled, in coil form, being EITHER of the following:
(a) grade SAE 1045, having a chemical composition by
weight of BOTH of the following:
(i) carbon NOT less than 0.42% and NOT greater
than 0.50%;
(ii) manganese NOT less than 0.50% and NOT greater than
0.80%;
(b) grade SAE 1055, having a chemical composition by weight of
BOTH of the following:
(i) carbon NOT less than 0.52% and NOT greater than
0.60%;
Item 50 applies unless otherwise stated.
Tariff Description
===========================================================================
(ii) mangenese NOT less than 0.60% and NOT greater than
0.90%
Op. 17.06.2005 Dec. 02.09.2005 - TC 0507513
7211.29.00 STRIP, steel annealed, cold rolled, in coil form, having ALL of
the following:
(a) chemical composition by weight of BOTH of the following:
(i) carbon - 0.45% to 0.50% (both inclusive);
(ii) manganese - 0.65% to 0.90% (both inclusive)
(b) to DIN standards 17 200 and 1 544;
(c) in ANY of the following sizes:
Width Thickness
(i) 47.0 mm x 3.00 mm
(ii) 84.0 mm x 2.26 mm
(iii) 83.0 mm x 3.20 mm
(iv) 62.0 mm x 4.00 mm
(v) 95.0 mm x 4.50 mm
(vi) 131.0 mm x 3.00 mm
(d) width tolerance + or - 1.00 mm;
(e) thickness tolerance + or - 0.09 mm
Op. 01.07.1996 Dec. 11.06.1996 - TC 9605769
7212.20.00 STEEL, flat rolled, tin plated, coil form, continuous annealed,
electro-galvanised zinc coated tab stock, having ALL of the
following:
(a) thickness gauge NOT greater than 0.4 mm;
(b) width NOT greater than 90 mm;
(c) coated internally and externally with food grade retortable
varnish
Op. 22.09.2005 Dec. 16.12.2005 - TC 0512719
7212.40.00 STEEL, cold rolled, less than 0.15% carbon, electro galvanized,
coated with primer and chemically reactive adhesive system
Op. 12.07.1993 Dec. 29.10.1993 - TC 9306903
7212.50.00 HOOP OR STRIP, thickness ranging from 0.2 mm to 1.2 mm, width less
than 600 mm, electroplated with ANY of the following:
(a) chromium;
(b) brass;
(c) copper;
(d) nickel
Op. 11.03.1994 Dec. 17.06.1994 - TC 9403622
7213.20.00 RODS, WIRE, hot rolled, free cutting steel, Grade 12L 14
Op. 07.11.2003 Dec. 30.01.2004 - TC 0314235
7213.91 RODS, tyre cord, dia 5.0 mm or greater but NOT exceeding 6.0 mm,
to Specifications AISI 1070 M or AISI 1080 M
Op. 01.07.1996 Dec. 12.06.1996 - TC 9607044
7214.30.00 BARS, ROUND, hot rolled, free cutting steel, Grade 12L 14
Op. 07.11.2003 Dec. 30.01.2004 - TC 0314225
7215.10.90 BARS, cold drawn, to American Iron and Steel Institute Standard
C 12L14 (AISI C 12L14)
Op. 15.10.2008 Dec. 14.01.2009 - TC 0835477
7215.90 BARS, square, steel, bright or cold finished, having an across the
flat dimension of 40 mm or greater but NOT exceeding 150 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8735564
7215.90 BARS, flat, high carbon spring steel, tempered and hardened to give
a tensile strength 80 to 90 tons/sq in, in straight lengths, cross
sectional dimensions 9 to 13 mm wide, 2.5 to 5 mm thick
Op. 07.05.1990 Dec. 09.08.1990 - TC 9004401
7216.50.00 BARS, MILD STEEL, being wheel rim profiles, length NOT less than
5 m
Op. 19.12.2005 Dec. 10.03.2006 - TC 0516804
7217.10 WIRE, high carbon steel, in shapes (OTHER THAN rounds) with shaved
edges, having BOTH of the following:
(a) a chemical composition by weight of ALL of the following:
(i) carbon - 0.65% to 1.05%;
(ii) manganese - 0.20% to 0.80%;
(iii) silicon - 0.15% to 0.35%;
(iv) phosphorus - 0.03% maximum;
(v) sulphur - 0.03% maximum;
(b) in ANY of the following nominal dimensions:
(i) 2.20 mm x 0.203 mm;
(ii) 2.28 mm x 0.610 mm;
(iii) 2.54 mm x 0.508 mm;
(iv) 2.62 mm x 0.610 mm;
(v) 3.05 mm x 0.610 mm;
(vi) 3.43 mm x 0.610 mm;
(vii) 3.81 mm x 0.610 mm;
(viii) 4.19 mm x 0.610 mm;
(ix) 6.14 mm x 0.457 mm
Op. 01.07.1996 Dec. 19.06.1996 - TC 9607613
7217.10 WIRE, bright soft annealed, dia 0.44 mm or 0.70 mm
Op. 01.07.1996 Dec. 20.06.1996 - TC 9607750
7217.10 WIRE, steel, high carbon, oil hardened and tempered, dia NOT
exceeding 0.9 mm
Op. 01.07.1996 Dec. 21.06.1996 - TC 9607805
7217.10 WIRE, oil tempered spring steel, having EITHER of the following:
(a) a dia NOT exceeding 1.25 mm;
(b) a dia exceeding 10.16 mm
Op. 01.07.1996 Dec. 21.06.1996 - TC 9607806
7217.20.00 WIRE, steel, flat rolled with round edges, zinc coated, capable of a
30 degree angle edgewise bend around a 6.35 mm radius without
surface cracking, having ALL the following:
(a) dimensions;
(i) width from 8.80 mm to 8.90 mm;
(ii) thickness from 3.00 mm to 3.1 mm;
(b) chemical composition by weight of ALL the following:
(i) carbon 0.35% to 0.45%;
(ii) copper 0.32% to 0.39%;
(iii) manganese 0.5% to 0.8%;
(iv) silicon 0.15% to 0.35%;
(v) phosphorus maximum 0.045%;
(vi) sulphur maximum 0.045%
Op. 01.07.1996 Dec. 02.01.1996 - TC 9600025
7217.20.00 WIRE, steel, flat, rolled with round edges, zinc coated, capable of
a 30 degree edgewise bend around a 6.35 mm radius without surface
cracking, having ALL of the following:
(a) dimensions:
i) width from 7.75 mm to 7.85 mm;
Item 50 applies unless otherwise stated.
Tariff Description
===========================================================================
ii) thickness from 3.00 mm to 3.1 mm;
(b) chemical composition by weight of ALL of the following:
i) carbon - 0.35% to 0.45%;
ii) copper - 0.32% to 0.39%;
iii) manganese - 0.5% to 0.8%;
iv) silicon - 0.15% to 0.35%;
v) phosphorus - maximum 0.045%;
vi) sulphur - maximum 0.045%
Op. 01.07.1996 Dec. 21.06.1996 - TC 9607834
7217.90.00 WIRE, STEEL, being hard drawn low carbon (HDLC) wire, phosphate
coated, having ALL of the following:
(a) diameter NOT less than 18.00 mm but NOT greater than
20.00 mm;
(b) chemical composition by weight of ALL of the following:
(i) carbon 0.04% to 0.10%;
(ii) phosphorus 0.03% maximum;
(iii) manganese 0.40% to 0.60%;
(iv) silicon 0.12% to 0.24%;
(v) sulphur 0.03% maximum
Op. 11.08.2008 Dec. 31.10.2008 - TC 0825942
7217.90.00 WIRE BEAD, bronze plated steel, having BOTH of the following:
(a) carbon content NOT less than 0.69%;
(b) tensile strength NOT less than 1 750 N/mm2
Op. 24.05.2004 Dec. 20.08.2004 - TC 0404954
7219.21.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS S30815, having a
chemical composition by weight of ALL of the following:
(a) carbon 0.1% maximum;
(b) silicon 1.40% to 2.00% (both inclusive);
(c) manganese 0.8% maximum;
(d) phosphorous 0.040% maximum;
(e) sulphur 0.030% maximum;
(f) chromium 20% to 22% (both inclusive);
(g) nickel 10% to 12% (both inclusive);
(h) cerium 0.03% to 0.08% (both inclusive);
(i) nitrogen 0.14% to 0.20% (both inclusive)
Op. 21.01.1994 Dec. 29.04.1994 - TC 9401453
7219.21.00 PLATES, stainless steel, types 304 and 316 to ASTM A240
Op. 21.11.1994 Dec. 19.05.1995 - TC 9409119
7219.22.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS S30815, having a
chemical composition by weight of ALL of the following:
(a) carbon 0.1% maximum;
(b) silicon 1.40% to 2.00% (both inclusive);
(c) manganese 0.8% maximum;
(d) phosphorous 0.040% maximum;
(e) sulphur 0.030% maximum;
(f) chromium 20% to 22% (both inclusive);
(g) nickel 10% to 12% (both inclusive);
(h) cerium 0.03% to 0.08% (both inclusive);
(i) nitrogen 0.14% to 0.20% (both inclusive)
Op. 21.01.1994 Dec. 29.04.1994 - TC 9401452
7219.22.00 PLATES, stainless steel, types 304 and 316 to ASTM A240, having a
thickness greater than 6mm
Op. 21.11.1994 Dec. 19.05.1995 - TC 9409118
7219.32.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS 31803, having a
chemical composition, by weight, of ALL the following:
(a) carbon 0.03% maximum;
(b) chromium 21.0-23.0% inclusive;
(c) nickel 4.5-6.5% inclusive;
(d) molybdenum 2.5-3.5% inclusive;
(e) nitrogen 0.08-0.20% inclusive;
(f) silicon 1.0% maximum;
(g) manganese 2.0% maximum;
Item 50 applies unless otherwise stated.
Tariff Description
===========================================================================
(h) phosphorus 0.03% maximum;
(i) sulphur 0.02% maximum
Op. 10.12.1992 Dec. 16.03.1993 - TC 9300334
7219.33.00 COILS, stainless steel, cold rolled, AISI type 436, having BOTH the
following:
(a) width exceeding 600 mm;
(b) thickness 1.0 mm or greater but NOT exceeding 3.0 mm
Op. 24.03.1993 Dec. 12.07.1993 - TC 9308961
7219.34.00 COILS, stainless steel, cold rolled, AISI type 436, having BOTH the
following:
(a) width exceeding 600 mm;
(b) thickness 0.5 mm or greater but NOT exceeding 1.0 mm
Op. 24.03.1993 Dec. 12.07.1993 - TC 9308956
7219.34.00 STAINLESS STEEL STRIP, cold rolled, heat resisting, ferritic, type
409, in coils, AISI type 2D finish, having the following dimensions;
(a) thickness 0.9 mm, 0.6 mm, or 1.00 mm (+ or - 10%);
(b) width between 600 mm and 1 300 mm inclusive
Op. 04.10.1996 Dec. 13.12.1996 - TC 9611259
7219.90.00 CAUL PLATES (melamine press plates), stainless steel, being 2 650 mm
x 1 350 mm OR greater
Op. 16.11.1998 Dec. 22.01.1999 - TC 9810123
7220.20.00 BANDING, stainless steel, to AISI 201 or 316, of a width less than
35 mm and a thickness of less than 1.25 mm
Op. 18.05.1993 Dec. 30.08.1993 - TC 9304905
7220.20.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, NOT further worked than
cold-rolled (cold-reduced)
Op. 02.06.1997 Dec. 15.08.1997 - TC 9704864
7220.90.00 STRIP, stainless steel, type 434, coated on one or both sides with
primer and chemically reactive adhesive system
Op. 21.03.1994 Dec. 02.08.1994 - TC 9403739