Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Page 1 of 6
Title: P112 HYBRID VEHICLE CONTROL: HYBRID CONTROL SYSTEM: P2122-104: Throttle / Pedal
Position Sensor / Switch "D" Circuit Low Input (2009 Prius)
P2122-
DTC Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input
104
P2123-
DTC Throttle / Pedal Position Sensor / Switch "D" Circuit High Input
105
P2127-
DTC Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input
107
P2128-
DTC Throttle / Pedal Position Sensor / Switch "E" Circuit High Input
108
DESCRIPTION
HINT:
This is the repair procedure for the accelerator pedal position sensor.
This electrical throttle system does not use a throttle cable.
This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal to detect how much it is
depressed. It has 2 sensor terminals (VPA and VPA2) to detect the accelerator pedal position and a
malfunction of the accelerator pedal position sensor itself. Since this sensor is electronically controlled
with hall elements, accurate control and reliability can be obtained.
In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the HV
control ECU changes between 0 V and 5 V in proportion to the degree of depressing the accelerator
pedal. The VPA is a signal to indicate the actual accelerator pedal position angle which is used for the
HV system control, and the VPA2 is a signal to indicate the actual accelerator pedal position angle
which is used for detecting a malfunction of the sensor itself (terminal VPA).
The HV control ECU judges how much the accelerator pedal is being depressed from the VPA and
VPA2 signals, and controls the HV system based on the signals.
https://techinfo.toyota.com/t3Portal/document/rm/RM10Q0U/xhtml/RM000001PRW... 18/08/2009
P112 HYBRID VEHICLE CONTROL: HYBRID CONTROL SYSTEM: P2122-104: ... Page 2 of 6
Wire harness or
Open or GND short in accelerator pedal position connector
P2122 104
main sensor circuit Accelerator pedal rod
HV control ECU
Wire harness or
+B short in accelerator pedal position main sensor connector
P2123 105
circuit Accelerator pedal rod
HV control ECU
Wire harness or
Open or GND short in accelerator pedal position sub connector
P2127 107
sensor circuit Accelerator pedal rod
HV control ECU
Wire harness or
+B short in accelerator pedal position sub sensor connector
P2128 108
circuit Accelerator pedal rod
HV control ECU
WIRING DIAGRAM
https://techinfo.toyota.com/t3Portal/document/rm/RM10Q0U/xhtml/RM000001PRW... 18/08/2009
P112 HYBRID VEHICLE CONTROL: HYBRID CONTROL SYSTEM: P2122-104: ... Page 3 of 6
INSPECTION PROCEDURE
PROCEDURE
READ VALUE USING THE TECHSTREAM (ACCEL PEDAL POS #1 AND ACCEL
1.
PEDAL POS #2)
(c) Enter the following menus: Powertrain / Engine Control / Data List.
(d) Read the "Accel Pedal Pos #1" and "Accel Pedal Pos #2" values on the Techstream with the
engine stopped.
OK:
Changes with accelerator pedal pressure
CHECK IF DTC OUTPUT RECURS (DTC
OK P2122, P2123, P2127 OR P2128)
NG
https://techinfo.toyota.com/t3Portal/document/rm/RM10Q0U/xhtml/RM000001PRW... 18/08/2009
P112 HYBRID VEHICLE CONTROL: HYBRID CONTROL SYSTEM: P2122-104: ... Page 4 of 6
(d) Measure the voltage between the terminals of the HV control ECU connector and body
ground.
Standard voltage:
(f) Measure the resistance between the wire harness side connectors.
Standard resistance (Check for open):
Standard resistance (Check for short)
https://techinfo.toyota.com/t3Portal/document/rm/RM10Q0U/xhtml/RM000001PRW... 18/08/2009
P112 HYBRID VEHICLE CONTROL: HYBRID CONTROL SYSTEM: P2122-104: ... Page 5 of 6
OK
https://techinfo.toyota.com/t3Portal/document/rm/RM10Q0U/xhtml/RM000001PRW... 18/08/2009
P112 HYBRID VEHICLE CONTROL: HYBRID CONTROL SYSTEM: P2122-104: ... Page 6 of 6
OK
NEXT
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
YES SYSTEM IS OK
https://techinfo.toyota.com/t3Portal/document/rm/RM10Q0U/xhtml/RM000001PRW... 18/08/2009