Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
In the figure, bars A and B, having circular Determine the deflection of the free end of
cross sections, are securely connected to the the Steel rod shown in the figure under the
rigid plate C and to the rigid supports. The given load (E = 200 GPa).
bars are unstressed when the load P is zero,
and the temperature remains constant. Bar
has a uniform taper from diameter “d” at the
bottom to diameter “2d” at the top (assume a
slight taper). The modulus of elasticity the
material of bar B is one-third that of the
material of bar A. For elastic action:
A uniform timber pile which has been La viga rígida horizontal ABCD esta
driven to depth L in clay carries an applied soportada por las barras verticales BE y
load of F at top. This load is resisted entirely CF, y está cargada con las fuerzas
by friction along the pile, which varies in the verticales P1 = 400 kN y P2 = 360 kN, que
parabolic manner f = ky2 (origin at bottom). actúan en los puntos A y D,
Show that total shortening of the pile is respectivamente. Las barras BE y CF son
FL/4AE. AE is the axial rigidity of the pile. de acero (E = 200 GPa) y tienen áreas
transversales ABE = 11100 mm2 y ACF =
9280 mm2. Las distancias entre los
diversos puntos de las barras se muestran
en la figura.
Determine los desplazamientos verticales
δA y δD de los puntos A y D,
respectivamente.
Una vez fabricada la pieza, se le somete a un esfuerzo axial de tracción de valor N = 720 kN. Se
pregunta:
At room temperature (70oF) a 0.02 – in. gap exists between the ends of the
rods shown. At a later time when the temperature has reached 320oF,
determine:
A rigid floor slab with mass of 3200 kg rests on three columns as shown in the figure.
What is the compressive stress en each of the members
a. At installation
b. After a temperature decrease of 20oC
WOOD
A = 0.04 m2
E = 12 GN / m2
L=2m
α = 6 * 10-6 (0C)-1
CONCRETE
A = 0.08 m2
E = 20 GN / m2
L=4m
α = 24 * 10-6 (0C)-1
Lista de Ejercicios No2 – I Semestre Académico del 2013
Asignatura: Mecánica de Solidos de Solidos
Profesor: José Miguel Benjumea
Suponga que ambos materiales son plásticos y perfectamente elásticos. Para el acero, sea σperm
= 24 ksi, σyp = 60 ksi y E = 30 * 106 psi y para el concreto, σperm = 2000 psi, σyp = 4600 psi y E
= 2 * 106 psi. (Se ha demostrado experimentalmente que cuando el acero fluye, la resistencia a
la “fluencia” del concreto es aproximadamente 0.85σult, donde σult es la resistencia última a
compresión de una probeta cilíndrica sin refuerzo del mismo material, edad y condiciones de
curado. Para lograr un comportamiento dúctil en las columnas, el uso de estribos o espirales
laterales de refuerzo es esencial.)
*Problema avanzado (no obligatorio). Lectura propia del estudiante.
αa = 125.10-7(1/0C), αc = 165.10-7(1/0C),
Ea = 2.106 kgf/cm2 y Ec = 106 kgf/cm2
Lista de Ejercicios No2 – I Semestre Académico del 2013
Asignatura: Mecánica de Solidos de Solidos
Profesor: José Miguel Benjumea
Se prevé la sujección de una barra AB perfectamente rígida mediante tres barras del
mismo material enlazadas por medio de articulaciones como se indica en la figura. Por
un error cometido al cortar las barras, la prevista situarla en posición vertical de
longitud l presenta un defecto Δ en su longitud. El área de las secciones de todas las
barras tienen el mismo valor Ω y el módulo de elasticidad E.