Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
V, Inc
320A Kalmus Drive Costa Mesa, CA 92626
TEL : +714-668-0588 FAX :+714-668-9099
Top Confidential
Table of Contents
CONTENTS PAGE
Sections
1. Features 1-1
2. Specifications 2-1
8. Waveforms 8-1
Appendix
1. Main Board Circuit Diagram
IBM and IBM products are registered trademarks of International Business Machines
Corporation.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
VESA, EDID, DPMS and DDC are registered trademarks of Video Electronics Standards
Association (VESA).
No part of this document may be copied, reproduced or transmitted by any means for any
purpose without prior written permission from VINC.
FCC INFORMATION
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that the interference will not occur in a particular installation. If this equipment
does cause unacceptable interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures -- reorient or relocate the receiving
antenna; increase the separation between equipment and receiver; or connect the into an
outlet on a circuit different from that to which the receiver is connected.
FCC WARNING
To assure continued FCC compliance, the user must use a grounded power supply cord and
the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized
changes or modifications to Amtrak products will void the user’s authority to operate this
device. Thus VINC Will not be held responsible for the product and its safety.
CE CERTIFICATION
This device complies with the requirements of the EEC directive 89/336/EEC with regard to
“Electromagnetic compatibility.”
SAFETY CAUTION
Use a power cable that is properly grounded. Always use the AC cords as follows – USA (UL);
Canada (CSA); Germany (VDE); Switzerland (SEV); Britain (BASEC/BS); Japan (Electric
Appliance Control Act); or an AC cord that meets the local safety standards.
3. Input Connectors
1x Co-axial RF (ATSC/QAM/NTSC)
4x HDMI™** with HDCP (1 with Stereo Audio RCA)
2x Component YPbPr plus Stereo Audio
1x RGB PC plus Stereo Audio
1x S-Video plus Stereo Audio (shared with AV1)
2x Composite Video plus Stereo Audio (AV1 & AV2)
USB FW Update
5. Speaker
Built in Speakers: 3 x 10 W, 2 way, 3.0 ch
Optional wireless speakers: Sub-woofer: 25W, SR+LR: 10W+10W
6. ENVIRONMENT
Operating Temperature: 5c~35c (Ambient)
Operating Humidity: Ta= 35 °C, 90%RH(Non-condensing)Operating Altitude: 0
- 14,000 ft
Non-Operating : 4000ft
7. DIMENSIONS (Physical dimension)
Dimensions with stand: 1000.9mm(W) x 690.4mm(H) x 241.4mm(D)
Dimension without stand: 1000.9mm(W) x 650.0mm(H) x 102.0mm(D) inches
Precaution
Please pay attention to the followings when you use this TFT LCD module.
1. OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower
than following voltage :
V=±200mV (Over and under shoot voltage)
(2) Response time depends on the temperature.
(In lower temperature, it becomes longer.)
(2) When the module with protection film attached is stored for a long time,
sometimes there remains a very small amount of glue still on the bezel after
the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel
surface or its vestige is recognized, please wipe them off with absorbent
cotton waste or other soft material like chamois soaked with
normal-hexane.
[MENU]
Operation Menu
PICTURE
1-0 Picture Mode(Custom, Standard, Vivid, Movie, Game, Football, Golf,
Basketball, Baseball)
1-1 Backlight(0~100)
1-2 Brightness(0~100)
1-3 Contrast(0~100)
1-4 Color(0~100)
1-5 Tint(-32~+32)
1-6 Sharpness(0~7)
1-7 Advanced Video
1-7-1 Noise Reduction(Off, Low, Medium, Strong)
1-7-2 Color Enhancement(Off, Normal, Rich Color, Green/Flesh, Green/Blue)
1-7-3 Advanced Adaptive Luma (Off, Low, Medium, Strong, Extend)
1-7-4 Enhanced Contrast Ratio(Off, On)
1-7-5 Color Temperature
1-7-5-1 Color Temperature(Cool, Normal, Warm, Custom)
1-7-5-2 Red(0~255)
1-7-5-3 Green(0~255)
1-7-5-4 Blue(0~255)
1-7-6 Smooth Motion
AUDIO
2-0 Audio Mode(Flat, Rock, Pop, Classic, Jazz)
2-1 Equalizer
2-1-1 120Hz
2-1-2 500Hz
2-1-3 1.5KHz
2-1-4 5KHz
2-1-5 10KHz
2-2 Balance(-50~+50)
2-3 Digital Audio Out(Off, Dolby Digital, PCM)
2-4 Speakers(On/Off)
2-5 Analog Audio Out(Fixed, Variable)
2-6 Lip Sync(0~5)
2-7 DRC(Off, 1/4, 1/2, 3/4, Full)
2-8 Wireless Speaker(On, Off)
2-9 Speaker Setting
2-9-1 Speaker Location
AUDIO
2-0 Audio Mode(Flat, Rock, Pop, Classic, Jazz)
2-1 Equalizer
2-1-1 120Hz
2-1-2 500Hz
2-1-3 1.5KHz
2-1-4 5KHz
2-1-5 10KHz
2-2 Balance(-50~+50)
2-3 Digital Audio Out(Off, Dolby Digital, PCM)
2-4 Speakers(On/Off)
2-5 Analog Audio Out(Fixed, Variable)
2-6 Lip Sync(0~5)
2-7 DRC(Off, 1/4, 1/2, 3/4, Full)
2-8 Wireless Speaker(On, Off)
2-9 Speaker Setting
2-9-1 Speaker Location
2-9-1-1 Auto
2-9-1-2 Left
2-9-1-3 Center
2-9-1-4 Right
2-9-1-5 Rear Left
2-9-1-6 Subwoofer
2-9-1-7 Rear Right
2-9-2 Trim
2-9-2-1 Left
2-9-2-2 Right
2-9-2-3 Rear Left
2-9-2-4 Rear Right
2-9-2-5 Center
CHANNEL
3-1 Tuner Mode(Cable, Antenna)
3-2 Auto Search
3-3 Partial Channel Search
3-3-1 Scan Mode (Analog, Digital, Analog/ Digital)
3-3-2 From Channel (1~135)
3-3-3 To Channel (1~135)
3-4 Skip Channel
3-5 MTS(ATV:Mono/Stereo/Sap;DTV:Language1/Language2/Language3)
Time Zone(Eastern, Indiana, Central, Mountain, Arizona, Pacific, Alaska,
3-6
Hawaii, Atlantic, Newfoundland)
3-7 Daylight Saving(On, Off)
SETUP
4-1 Language(English, Francais, Espanol)
4-2 PIP
4-2-1 PIP Mode (Off, PIP, POP)
4-2-2 PIP Source(TV,…)
4-2-3 PIP Size(Small, Medium, Large)
4-2-4 PIP Position(TL,…, BR)
4-2-5 Audio Source (Main or PIP)
[INFO]
“INFO” button could show an information bar which displays the information about
the input signal on our LCD TV.
Start
N0
1. Is Power board output +5VSB (F1)?
2. Is J1 connector of MB good?
LED is lighted
3. Is DC-DC OK?
(OrangeÎgreen) 4. Is U22 pin2 (+3V3SB) working ok?
Yes
It is in power saving
N0
1. Check video cable
LED is lighting? 2. Is the timing supported?
3. Check sync input
4. Check VGA SOG rout if analog (SOG) (C132)
Yes
Yes
END
Start
N0
Yes
N0
1. Check P14 signal
2. Check signal between P14 and U13 (IF AV1 mode)
U13 input correct? 3. Check Tuner & U13 (IF TV mode)
4. Check P15 (IF AV2 mode)
5. Check U13 POWER 3.3V
Yes
N0
LVDS output 1. Check LVDS LINE(J12/MEMC BD LVDS out)
2. Check U13 clock (60MHz)(X1)
3. Check U13 Power
Yes
END
Start
N0
Yes
Yes
N0
1. Check signal between U13 & P3 or P14
U13 input correct? 2. Check Y1 Clock (60MHZ)
Yes
N0 1. Check U13
Is LVDS output 2. Check U13 power 3.3V&2.5v&1.8v&1.25v
Yes
END
Start
N0
Yes
Yes
N0
1. Check signal between U13 & P15
U13 input correct? 2. Check Y1 Clock (60MHZ)
Yes
N0 1. Check U13
Is LVDS output 2. Check U13 power 3.3V&2.5v&1.8v&1.25v
Yes
END
Start
N0
Yes
N0
U13 no data out ? 1. Check P8&P9 connect
2. Check the pin18 & 19 of P8& P9
3. Check the pin 6 of U33& U34
Yes
Yes
END
Start
N0
Yes
N0
U13 no data out ? 1. Check P15 & P16 connect (MB)
2. Check P503 & P506 connect (SIDE JACK BD)
3. Check the pin10 & 11 of P16 (MB)
4. Check the pin 5/6 of U503 U504 (SIDE JACK BD)
Yes
Yes
END
Start
Yes
Yes
No
The voltage is about +3.3V
U15, U17,U22 1. Check F1 & U14
2. Check U15, U17, U22
Yes
Yes
No
The voltage is about +2.5V while power switch on
U19 pin2 1.Check J1 Connect
2.Check U19 pin2
Yes
END
Start
N0
Support DDC1/2B
1. Analog cable ok?
Is Analog DDC OK?
2 .Check signal (U31 to P5)
3. Check U31 Voltage
4. Is protocol compliant?
Yes
N0
Support DDC1/2B
1. Analog cable ok?
Is HDMI DDC OK?
2. Check signal (U 33 to P8)
3. Check signal (U34 to P9)
4. Is protocol compliant?
Yes
END
Start
Yes
No 1. J2 of cable is good.
Audio BD 2. Check F1 is good
3. J4/J6 of speaker connect are good.
4. J3 of cable is good.
Yes
No
1. Check J2/J4/J1/J3 connect and cables are good.
EMI BD
Yes
No
1. Check JC1/JC2 connect and cables are good.
2. Pin1 of JC1 is 5V
TX BD/TX card 3. Pin2 of JC2 is 3.3V
4. connection is good between J1 and TX card.
Yes
No 1. AC cable is good.
2. SL/SR speaker and cable are good.
Sub-woofer
Yes
END