Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
** ON A/C ALL
TASK 71-00-00-000-042-A
Removal of the Power Plant
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
GEAR. MOVEMENT OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAM-
AGE TO THE AIRCRAFT AND/OR EQUIPMENT.
WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN
CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE YOU
SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL
MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
NOTE: Interferences between the LPTACC Inlet Airscoop assy and the Thrust reverser cowl have been ob-
served in production on a limited number of A320 Family aircraft powered with CFM56-5B/3 engines.
CFM has issued SB CFM56-5B S/B 75-0044. In order to recover the gap between the LPTACC scoop
and the Thrust reverser cowl to avoid potential interference, Airbus recommends to incorporate this SB
at the opportunity of Engine Removal/Installation.
B. Consumable Materials
REFERENCE DESIGNATION
(Material No. CP8001) lockwire 0.032 in. (0.8 mm) dia.
(Material No. CP8002) lockwire 0.032 in. (0.8 mm) dia
D. Referenced Information
REFERENCE DESIGNATION
** ON A/C 001-050
(Ref. 05-57-00-200-001-A). Aircraft Stability
** ON A/C 051-150
(Ref. 05-57-00-200-001-B). Aircraft Stability
** ON A/C ALL
(Ref. 24-41-00-861-002-A). Energize the Aircraft Electrical Circuits from the External Power
(Ref. 24-41-00-861-002-A-01). Energize the Aircraft Electrical Circuits from the APU
(Ref. 24-41-00-861-002-A-02). Energize the Aircraft Electrical Circuits from Engine 1(2)
(Ref. 27-80-00-866-005-A). Retracting the Slats on the Ground
(Ref. 29-14-00-614-001-A). Depressurization of the Hydraulic Reservoirs
(Ref. 31-36-00-740-015-A). Printout of the Engine/APU Hours and Cycles Stored in the Flight Data
Interface and Management Unit (FDIMU)
REFERENCE DESIGNATION
** ON A/C 002-150
PRE SB 36-1055 for A/C 002-003, 051-054, 101-101
(Ref. 36-11-49-000-026-A). Removal of the Sense Line between the Bleed Pressure-Regulator
Valve (PRV) and the Pylon Interface
** ON A/C ALL
(Ref. 71-13-00-010-040-B). Opening of the Fan Cowl Doors
(Ref. 71-13-00-410-040-B). Closing of the Fan Cowl Doors
(Ref. 71-73-49-000-025-A). Removal of the Fuel Overboard Drain Tube
(Ref. 78-30-00-481-041-B). Make the Thrust Reverser Unserviceable for Maintenance
(Ref. 78-36-00-010-040-B). Opening of the Thrust Reverser Doors
(Ref. 78-36-00-410-040-B). Closing of the Thrust Reverser Doors
Fan Duct Panels and Sealing Fitting Assy SHEET 1
Hold Open Cowl Braces - Installation SHEET 1
Thrust Reverser Electrical Connectors SHEET 1
Power Plant - Right Side SHEET 1
Power Plant - Left Side SHEET 1
Pneumatic System SHEET 1
Forward Engine Mount SHEET 1
Bootstrap Installation
Aft Engine Mount SHEET 1
UPPER
STRUT
N_MM_710000_4_RAM0_01_00
Figure 71(CFMB)-00-00-991-91000-06-A / SHEET 1/1 - Fan Duct Panels and Sealing Fitting Assy
** ON A/C ALL
N_MM_710000_4_RBM0_01_00
B A
FLANGE
STA 191 (B6)
FLANGE
STA 199 (A2)
B FUEL
PYLON FILTER
JUNCTION
BOX DRAIN
PLUG
454VC-A
450VC-A
452VC-A
457VC-A
PYLON
CORE
ELECTRICAL
HARNESS C1M-245-00
N_MM_710000_4_RCM0_01_00
A
A
404VC -A
403VC -A
402VC -A
447VC -A
448VC -A
406VC -A PYLON
407VC -A JUNCTION
BOX
408VC -A
FLANGE STA.
405VC -A 158 (B1)
401VC-A
409VC-A
400VC-A
PYLON
DUCT
10
15 5
CHECK VALVE 20
RESTRICTOR
PIPE
25
FLANGE STA.
167 (B4)
4102KS-A
HYDRAULIC
CONTROL 4101KS-B
UNIT
UPPER
4101KS-A FLANGE STA. STARTER
199 (A2) DUCT
C1M-290-01
N_MM_710000_4_RDN0_01_01
FLANGE
STA 176 (B4) A
FLUID TO CHECK
10 DISCONNECT VALVE
PANEL
COUPLING RESTRICTOR
HALF PIPE ON HCU
FLANGE
STA 185 (B5)
60
175
FLANGE
STA 199 (A2)
55
50
40 45
(4 PLCS)
4100KS-A
15
THRUST
20 REVERSER
30
(4 PLCS) JUNCTION
4100KS-B BOX
35
(4 PLCS)
25
(4 PLCS)
C1M-247-05
N_MM_710000_4_REM0_01_01
PYLON
PYLON
DUCT
65
70
(SEE NOTE)
UNION
HIGH PRESSURE
MANIFOLD DUCT
PYLON
INTERFACE
INTERFACE DUCT
TUBES
75
80
BLEED PRESSURE
REGULATOR VALVE
C1M-349-00
N_MM_710000_4_RFM0_01_00
A 85
(4 PLCS)
90
(4 PLCS)
PYLON
95
100
(4 PLCS)
105
(4 PLCS)
120
(4 PLCS)
125
(4 PLCS)
115
(4 PLCS)
110
(4 PLCS)
C1M-249-03
N_MM_710000_4_RGM0_01_00
B
A
A 1 2 1
3
5
4
2
B
N_MM_710000_4_RHM0_01_00
N_MM_710000_4_RHM0_02_00
A A
135
(4 locations)
140
(4 locations)
PYLON
SHEAR PIN
B 145
CAUTION
RETAINER 150 B
N_MM_710000_4_RJM0_01_00
3. Job Set-up
Subtask 71-00-00-740-052-A
A. Do a print-out of the engine hours and cycles and keep the print with the engine for follow-up
(Ref. AMM TASK 31-36-00-740-006) or (Ref. AMM TASK 31-36-00-740-007) or (Ref. AMM TASK 31-
36-00-740-015) .
NOTE: Some tasks will possibly not be applicable depending on whether a DMU or an FDIMU is installed
on the aircraft.
Subtask 71-00-00-941-066-A
B. Safety Precautions
(1) Make sure that aircraft is stable (Ref. AMM TASK 05-57-00-200-001) .
NOTE: If the aircraft is on jacks, make sure that it is leveled before you remove the engine.
WARNING: OPEN THE PROBE HEATER CIRCUIT-BREAKERS 1DA1(2), 3DA1(2,3), 4DA1(2,3) AND
5DA1(2,3) BEFORE ENG1(2)FADEC A AND EIU 1(2) C/B'S 2KS1 AND 2KS2. IF YOU DO
NOT OBEY THIS SEQUENCE:
- THE PROBES WILL BECOME TOO HOT.
- THIS CAN CAUSE DAMAGE TO EQUIPMENT AND INJURY TO MAINTENANCE PER-
SONNEL.
** ON A/C ALL
49VU ENGINE/1 AND 2/IGN/SYS A 1JH A03
49VU ANTI ICE/PROBES/AOA/1 4DA1 D04
49VU ANTI ICE/PROBES/PITOT/1 3DA1 D02
49VU ANTI ICE/RAIN/RPLNT/CAPT 1DB1 D01
** ON A/C ALL
121VU RCDR/DFDR 7TU K16
121VU ENGINE/ENG1 AND 2 FIRE EX- 2WE1 Q44
TIG/BTL1/SQUIB/B
121VU ENGINE/ENG1 AND 2 FIRE EX- 1WE1 Q43
TIG/BTL1/SQUIB/A
121VU ENGINE/ENG1 AND 2 FIRE EX- 2WE2 Q42
TIG/BTL2/SQUIB/B
121VU ENGINE/ENG1 AND 2 FIRE EX- 1WE2 Q41
TIG/BTL2/SQUIB/A
122VU ANTI ICE/WINDOWS/R 4DG2 W14
122VU ANTI ICE/RAIN/RPLNT/F/O 1DB2 W11
122VU ANTI ICE/WINDOWS/L 4DG1 X14
122VU ANTI ICE/PROBES/2/TAT 1DA2 Y15
122VU ANTI ICE/PROBES/2/PITOT 3DA2 Y14
122VU ANTI ICE/PROBES/2/AOA 4DA2 Y13
122VU ANTI ICE/PROBES/2/STATIC 5DA2 Y11
122VU ANTI ICE/PROBES/3/PITOT 3DA3 Z16
122VU ANTI ICE/PROBES/3/AOA 4DA3 Z15
122VU ANTI ICE/PROBES/3/STATIC 5DA3 Z14
122VU ANTI ICE/PROBES/1/STATIC 5DA1 Z13
122VU ANTI ICE/PROBES/1/TAT 1DA1 Z12
FOR FIN 1000EM1 (ENGINE-1)
49VU FUEL/LP VALVE/MOT1/ENG1 1QG A08
49VU ENGINE/1/FIRE DET/LOOP A 7WD1 A06
49VU ENGINE/1/FADEC A/AND EIU 1 2KS1 A04
121VU FUEL/LP VALVE/MOT2/ENG1 3QG M25
121VU ENGINE/IGN/ENG1/SYS B 3JH1 P41
121VU ENGINE/IGN/ENG1/SYS A BAT 2JH1 P39
121VU ENGINE/ENG1/FIRE DET/LOOP B 8WD1 Q38
121VU ENGINE/ENG1/FADEC B/AND EIU 1 4KS1 R41
122VU ELEC/GCU/1 2XU1 T26
122VU ANTI ICE/ENG/1 1DN1 X10
FOR FIN 1000EM2 (ENGINE-2)
49VU FUEL/LP VALVE/MOT1/ENG2 2QG A09
49VU ENGINE/2/FIRE DET/LOOP B 8WD2 A07
49VU ENGINE/2/FADEC A/AND EIU 2 2KS2 A05
121VU FUEL/LP VALVE/MOT2/ENG2 4QG M26
121VU HYDRAULIC/HYD POWER/Y 3803GX N30
WARNING: OPEN THE PROBE HEATER AND WINDOW HEATER CIRCUIT-BREAKERS BEFORE
YOU OPEN THE PHC AND WHC CIRCUIT BREAKERS. IF YOU DO NOT OBEY THIS SE-
QUENCE:
- THE PROBES WILL BECOME TOO HOT.
- THIS CAN CAUSE DAMAGE TO EQUIPMENT AND INJURY TO MAINTENANCE PER-
SONNEL.
CAUTION: BEFORE OPENING THE THRUST REVERSER DOORS TO THE 45 DEGREES POS-
ITION MAKE SURE THAT THE SLATS ARE RETRACTED. IF NOT THE SLATS CAN
TOUCH THE INBOARD THRUST REVERSER DOOR.
(1) Open the thrust reverser doors to the 45 degrees position (Ref. AMM TASK 78-36-00-010-040) :
(2) FOR 1000EM1 (ENGINE-1)
451AL, 452AR
(3) FOR 1000EM2 (ENGINE-2)
461AL, 462AR
Subtask 71-00-00-941-068-A
M. Put the ACCESS PLATFORM 1M(3 FT) in position at the engine level.
(1) At the half upper part of the fan frame seal the fan duct panels with TAPE - ADHESIVE
(Ref. Fig. Fan Duct Panels and Sealing Fitting Assy SHEET 1)
Subtask 71-00-00-480-059-A
N. Retract Fan and Thrust Hold Open Rods
(1) Install BRACE - HOLD OPEN COWLS (S587-2BH0) or BRACE-HOLD OPEN COWLS (TMHBS10-
10-00) to support the fan and thrust reverser cowl doors.
(Ref. Fig. Hold Open Cowl Braces - Installation SHEET 1)
(2) Retract the fan cowl hold open rods (Ref. AMM TASK 71-13-00-410-040) .
(3) Retract the thrust reverser doors hold open rods (Ref. AMM TASK 78-36-00-410-040) .
Subtask 71-00-00-680-051-A
P. Drain the remaining fuel from the engine and the pylon fuel hose at the fuel filter as follows :
(Ref. Fig. Thrust Reverser Electrical Connectors SHEET 1)
(1) Put a CONTAINER 4 L (1 USGAL) under the fuel filter.
(2) Cut and remove the lockwire or safety cable and remove the drain plug from the filter bowl. Drain the
fuel into the container.
(3) Install the drain plug and TORQUE to between 45 and 55 lbf.in (0.51 and 0.62 m.daN). Safety
with lockwire 0.032 in. (0.8 mm) dia. (Material No. CP8001), or lockwire 0.032 in. (0.8 mm)
dia (Material No. CP8002).
Subtask 71-00-00-010-095-B
Q. Remove the components:
(1) At the rear of the drain mast remove the drain tube (Ref. AMM TASK 71-73-49-000-025) .
(2) Remove the access panels :
(3) FOR 1000EM1 (ENGINE-1)
473AL, 473AR
(4) FOR 1000EM2 (ENGINE-2)
483AL, 483AR
(5) Remove these components from the right side of the engine :
(a) Disconnect the electrical connectors 450VCA, 452VCA, 454VCA, and 457VCA from the aft pylon
junction box.
(Ref. Fig. Thrust Reverser Electrical Connectors SHEET 1)
NOTE: If necessary, use the PLIERS - NOSE, SOFT, LONG to loosen the electrical connectors.
(b) Remove the two clamps which attach the core harness to the pylon and keep them attached to
the harness.
NOTE: Two clamp sizes can be found depending of the core harness diameter. To make sure
that the correct clamps are installed, keep the clamps attached to the harness.
(c) Disconnect the generator harness connector 400VCA from the forward pylon junction box.
(Ref. Fig. Power Plant - Right Side SHEET 1)
(d) Disconnect the thrust reverser harness connectors 4101KSB, 4101KSA and 4102KSA from the
thrust reverser hydraulic control unit.
(Ref. Fig. Power Plant - Right Side SHEET 1)
(e) Remove the screw (15) and nut (20) that attach the clamps (10), (25) to the bracket on the HCU.
(f) Remove the clamp (10) from the harness for connector 4101KSB and remove the harness from
the HCU.
NOTE: Loosely install the screw (15) and nut (20) on the clamp (25) and tighten with your hand.
(g) Disconnect the electrical connectors 401VCA, 402VCA, 403VCA, 404VCA, 405VCA, 406VCA,
407VCA, 408VCA, 409VCA, 447VCA, and 448VCA from the forward pylon junction box.
(Ref. Fig. Power Plant - Right Side SHEET 1)
(h) Remove the coupling (5) and disconnect the upper starter duct from the pylon duct.
(Ref. Fig. Power Plant - Right Side SHEET 1)
(i) Install COVER - PROTECTION on the open ends of the ducts.
(j) Install PLUG - BLANKING on the electrical connectors.
(6) Remove these components from the left side of engine:
(a) Disconnect the thrust reverser harness connector 4100KSA and 4100KSB from the electrical
junction box.
(b) Disconnect the coupling half on the suction hose (60), the pressure hose (55), and the upper
case drain hose (50) from the fluid disconnect panel.
(Ref. Fig. Power Plant - Left Side SHEET 1)
(c) Disconnect hose/tube (175) from the check valve restrictor pipe interface on the HCU.
(Ref. Fig. Power Plant - Left Side SHEET 1)
(d) Remove the bolts (35), the washers (40) that attach the fuel/return by-pass hose (45), from the
fluid disconnect panel. Remove and discard the gasket (10).
(Ref. Fig. Power Plant - Left Side SHEET 1)
(e) Remove the bolts (25), the washers (30) that attach the main fuel supply hose (20) to the fluid
disconnect panel. Remove and discard the gasket (15).
(Ref. Fig. Power Plant - Left Side SHEET 1)
(f) Install the COVER - PROTECTION on the disconnected hoses and tubes.
1 Disconnect the sense tubes (75) and (80) from the pylon interface tubes.
(Ref. Fig. Pneumatic System SHEET 1)
2 Disconnect the pressure tube (70) from the union installed in the upper high-pressure
manifold duct (engine 1 only).
(Ref. Fig. Pneumatic System SHEET 1)
3 Remove the coupling (65) and disconnect the pylon interface duct from the pylon duct.
(Ref. Fig. Pneumatic System SHEET 1)
** ON A/C 002-150
PRE SB 36-1055 for A/C 002-003, 051-054, 101-101
Subtask 71-00-00-020-078-A
R. Removal of the Pressure Regulator Valve (PRV) Sense Line
(1) Remove the sense line between the bleed pressure regulator valve (PRV) and the pylon interface
(Ref. AMM TASK 36-11-49-000-026) .
** ON A/C ALL
Subtask 71-00-00-020-060-A
S. Loosen the forward engine mount bolts.
(1) Remove the bolts (100), the washers (105) and (115), and nuts (110) that attach the nut retainers
(125).
(Ref. Fig. Forward Engine Mount SHEET 1)
(2) Cut and remove the lockwire or safety cable and loosen the bolts (85) as follows:
(a) Loosen one bolt. TORQUE again the bolt
to between 12 and 18 m.daN (88.50 and 132.74 lbf.ft) or to the maximum load that a mechanic
can apply with a standard wrench.
(b) Apply this procedure on the three remaining bolts one by one.
Subtask 71-00-00-480-060-A
T. Installation of the booststrap system:
(1) Install BOOTSTRAP-SYSTEM (98D71203500000) .
(Ref. Fig. Bootstrap Installation)
(a) Install the rear beam (9) on the lower part of the pylon and attach with the pins (8).
(b) Install the spacer and the center hinge clamp (6) on the pyramid. Attach the spacer to the
pyramid with the right and left clamps (7).
(c) Install the forward hinge arms (4) and (5) with the pins (3).
(d) Install the link (2) at the upper part of the hinge arms (4) and (5) with the pins (1).
(e) Install the dynamometers and the chain pulley blocks.
(2) Install the engine cradle:
CAUTION: BE CAREFUL WHEN YOU INSTALL THE CRADLE ON, OR REMOVE IT FROM, THE
ENGINE. IF NOT, YOU CAN CAUSE DAMAGE TO THE VIBRATION SENSOR CON-
NECTOR. THE VIBRATION SENSOR CONNECTOR IS IN FRONT OF THE FOR-
WARD HANDLING POINT ON THE RIGHT SIDE.
NOTE: Make the engine cradle level. To do this use the chain pulleys.
(5) Put the pins of the front fixtures into the engine handling points and then install the rear support on
the left side. Attach to the engine with a pin.
NOTE: The pin of the rear support on the left side must be put in the lower hole of the engine bracket.
(6) Put the pins into each fixture. Then, at the same time, adjust the tension of the handling hoists so
that you can read these values on the dynamometers : 1975 daN (4440 lbf) (2015 kg) for the forward
dynamometers and 400 daN (900 lbf) (408 kg) for the aft dynamometers.
4. Procedure
Subtask 71-00-00-020-061-A
A. Remove the bolts of the engine mounts
WARNING: DEATH OR SERIOUS INJURY MAY RESULT IF THE POWER PLANT FALLS ON
THE PERSONNEL. THE POWER PLANT WEIGHS APPROXIMATELY 6280 POUNDS
(2850KG). MAKE SURE THAT ALL PERSONNEL IS AWAY FROM THE AIRCRAFT
WHEN THE POWER PLANT IS REMOVED.
(1) Remove the bolts (85), washers (90), nuts (120) that attach the forward engine mount (95) to the
pylon.
(Ref. Fig. Forward Engine Mount SHEET 1)
(2) Remove the bolts (135) and washers (140) that attach the aft engine mount (145) to the pylon.
(Ref. Fig. Aft Engine Mount SHEET 1)
Subtask 71-00-00-869-177-A
B. Make sure that no lines or unions stay connected to the pylon.
Subtask 71-00-00-480-061-A
CAUTION: MAKE SURE THAT THE PYLON FORWARD MOUNT DOES NOT TOUCH THE UPPER
STRUT OR THE UPPER SEAL ASSY WHEN YOU LOWER THE ENGINE OR DAMAGE CAN
OCCUR.
NOTE: Use the level indicators on the forward hinge arms of the bootstrap to keep this hinge arms as
near as possible to the horizontal position.
NOTE: Be careful not to cause dynamic effects while you lower the engine.
(2) Put first the aft section of the engine cradle in position on the trolley then the forward section.
(3) Lock the engine cradle to the trolley with pins.
(4) Remove the four chain hooks from the engine cradle stirrups and remove the four chain pulley blocks
from the bootstrap system.
Subtask 71-00-00-020-059-A
CAUTION: OBEY THESE PRECAUTIONS WHEN YOU TOW OR MOVE THE AIRCRAFT ON THE
GROUND WITH THE ENGINE REMOVED AND THE THRUST REVERSER INSTALLED:
- THE THRUST REVERSER MUST BE CLOSED AND LATCHED.
- THE FAN COWLS MUST BE REMOVED.
- THE SPEED OF THE AIRCRAFT MUST BE 2 KM/H OR SLOWER.
- PREVENT SUDDEN MOVEMENTS OF THE THRUST REVERSER.
IF YOU DO NOT OBEY THESE INSTRUCTIONS, YOU CAN CAUSE DAMAGE TO THE NA-
CELLE STRUCTURE.
NOTE: When you lower the engine, check that the assembly is level and never in a nose down attitude.
Subtask 71-00-00-480-082-A
E. Installation of the Aft Engine Mount Anti Gouge Splints
(1) Put the top splint assemblies (larger) on the outside of the aft engine mount links.
NOTE: The end of the splint assembly marked TOP must touch the beam assembly. The other end
marked BOTTOM must touch the links.
(2) Put the bottom splint (smaller) on the inside of the aft engine mount links.
(3) Attach the SPLINT-ENGINE MOUNT AFT (RSE1224) to the engine mount two places with TIE
WRAP.
(a) Wind the TIE WRAP around the splints and the aft mount where the splint touches the beam
assembly.
(b) Wind the TIE WRAP around the splints and the aft mount where the splint touches the link.
(c) Make sure that the TIE WRAP is wound very tight and that the splints can not move.
End of document