Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
POLYMOBIL III
RX
Service Instructions
from Serial no. 3000
0 Siemens AG 1995
The reproduction, transmission or
us8 of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
granl or registration of a utility
I model or design, are resewed.
Register 5 English
Print No.: RX88-115.061.02.01.02 Date: 10.95
Replaces: n.a.
Chapter 0 Revision
Page 2 of 4
This page intentionally left blank.
4 Notes on troubleshooting 49 1
Checking the line voltage, fuses and LEDs ...................... .4 - 1
Checking the supply voltages ............................. .4 - 6
Checking the intermediate circuit voltage ....................... .4 - 8
Checking the maximum main inverter frequency ................... -4 - 9
Oscillating current measurement ........................... 4 - 10
Checking the high-voltage kVNoM and kV,cT ..................... 4 - 12
Checking the filament and tube current ........................ 4 - 13
Setting the maximum filament frequency ....................... 4 - 15
Checking the tube current. .............................. 4 - 16
Checking the kV and tube current (IR) ........................ 4 - 17
Checking the mAs values ............................... 4 - 18
Adjusting the mAs ................................... 4 - 19
Aligning the light field to the radiation field ...................... 4 - 20
Checking and readjusting the counterweight ..................... 4 - 23
Readjusting the counterweight with accessories attached .............. 4 - 23
Checking the control elements on the collimator ................... 4 - 24
11 CAUTION ‘11
1
All texts marked “Caution!” contain information regarding poten-
I’
tial hazards and steps to be taken to avoid hazards.
, -I
Documents required
l Wiring diagram X0381
l Description of functions RXB&115.641.02...
l Connect the POLY MOENL I II only to a power source (power outlet) meeting the
standards of VDE 0107 or the usual local standards.
l Before working on the open POLYMOBIL III switch OFF the unit with the power switch at
the control panele and unplug the power cable.
l Before removing or inserting PC boards, switch off the generator; in doing so, observe
the ESD regulations.
[j[ All Allen screws must have a tensile strength rating of 8.8.
Cleaning
l The unit must always be switched off or disconnected before cleaning.
l Use only water or a luke warm mixture of a household cleaner diluted with water to clean
the unit.
l Do not use an abrasive or organic solvents or cleaning agents containing solvents such
as gasoline used for cleaning purposes, alcohol or stain remover. Do not spray water on
the unit.
l For further information, refer to the Operating Instructions Y2leaningIDisinfecting”.
Fig. 1
. POLYMOBIL ON
l Connect radiation detector to the oscilloscope and place it in the beam path of the
POLYMOBIL III (see Fig. 1).
l Set the slide switch on the radiation detector to measuring range 1 (1 point visible).
l Set an SID of 40 cm and collimate onto the radiation detector with the light localizer
(Fig.1).
l Trigger check exposures using the exposure data specified in the oscillograms (see
Fig.2).
70 kVll0 mAs
60 kV/lO mAs
60 kW40 mAs
CHl: 10.0 mV : 200 ms’
CH2: 10.0 mV : 200 ms
60 kW20 mAs
CH3: 10.0 mV : 200 ms
60 kVil0 mAs
Fig. 2
lnitialization error
go... EPROM check sum error
95.. (l-t,,, circuit error
96.. mAno,.,,circuit error
97... kv,,,,., circuit error
Stand-by error:
03... IH, c IHstby
04... IHaCt> IHstby
05.. kV,,,<>O
06... mAad<>
09... High pressure in the tank
Exposure error:
Il... lnverter short circuit
12... kVmax
13... Imax
14... kV,, < kVnom
15.. mAact c mAnom
16... mA, > mAnom
17... maximum exposure time
18... exposure not completed
l Plug the power plug of the POLYMOBIL into the safety socket.
l POLYMOBIL ON
. POLYMOBIL OFF.
Fig. 1
Fuse value: 15 A
09’20 (X0381-92;)
Loosen the 4 Allen screws (ZFig.1, 4 mm key size) and remove the cover.
Fl 2 AT Closing circuit
F2 2 AT Closing circuit
F3 0.25 AT Tl secondary
F5 4 AT Filament circuit
F6 3.2 AT 24 V / Main inverter control
F7 10 AT Light-beam localizerr
0920 (X0381-92D)
After the initialization, the default data 60 kV and 10 mAs are displayed.
Stand-by operation
l On D920 the following LEDs are illuminated:
V40 (yellow) +24V
V39 (yellow) hament
V41 (yellow) I / 0 (ON/OFF)
V35 (yellow) + 300 V intermediate circuit voltage
KV mAa
-I
D910 (X0381-91E)
Preparation ON
l In addition, VI3 (green) lights up on D910.
Trigger an exposure
l In addition, the following LEDs light up on D910:
V15 (green) exposure
VI8 (green) SS
V28 (yellow) radiation display
Error message
l V16 (red) lights up on D910.
_1
I3920 (X0381-92D)
Measured voltage
in stand-by mode approx. 18.5 V Tolerance + 4 V
with preparation approx. 16.4 V Tolerance + 3 V
‘I,. - 7 - - - - .
I
I L ___---A
.I
j/ gl !Il
LP
KV mh
II91 0 (X0381-91E)
L Oszilloskop d
DVM
Dill (X0381-1116)
l Depending on the supply voltage, a value between 250... 350 V DC must be measured
with the digital multimeter.
I
314 v
050 v :!is
t t
HR “’ t
relay relay :
ON OFF
- Err 15 is displayed.
- No radiation.
05.0 v : lops
F =lOkHz
TLr= 100 ps Tolerance: + 0 ps / - 5 ps
. POLYMOBIL ON
l Trigger exposure with default values 60 kV, 10 mAs.
Main inverter ok
l During the kV rise
TeK Run: 1 .COMS/s Hi&s Trig?
-r r 1
L 1
I
I
lVg5OA
/ I 1
.,us 41)omV
1.00 v : 500 ms
2 20 kV
KV
IH
POLYMOBIL ON+t 1
Nominal
value output
Stand by
filament circuit
f
C. ON
Lb ON
t
+
e / b OFF
IHS
I I II Ill III I
TeKStop:Single~q 2.SOMWs
Stand by filament
current
I
T I
/
G-
L _
Exposure filament
I ‘L L! current
bl LO.OYS U-l‘J f 2.40”
ET1 2*30v z.oc v 20 .OMS
jl Err 3 is displayed.
l Using P3, set the maximum filament frequency on D910 (100 kHz 1 10 ps)
CH2:
,
Chapter 4 Notes on trouble-shooting
Page 16 of 24
Checking the tube current
l Connect oscilloscope on D910 to MP WS” (NOMINAL), “IR” (ACTUAL) and GND”.
POLYMOBIL ON
A&4 l
0 Trigger an exposure with the default values 60 kV, 10 mAs.
: 500 ms
: 500 ms
kV CH2: 1 .OO V : 50 ms
CH3: 1.00 V : 50 ms
IR
kV CH2: 1.00 V : 5 ms
CH3: 1.00 V : 5 ms
) NOTICE 1 The transient response of the tube current can be set with Pl on
- D910 .
Fig. 2
I /
Setting at control panel ) valid mAs values
I 40 kV, 200 mAs I 195 . . . 205 mAs I
66 kV, 100 mAs 97 .. . 103 mAs
90 kV, 1 mAs 1 ,O . . . 1,3 mAs
l Remove the mAs meter and reinsert the jumper in the single tank at “mA+ / mA -“.
l Reinstall the lid of the single tank.
1 V 2 3.2 kHz
5V e 16kHz
I I t
! ! 1
j-- 62-5 P ---+
Length
Marking
Side marking
Fig. 3
- Film
- Light field
- Radiation field
I y2
Fig. 4
Evaluation:
l Measure the deviations between light field edges and radiation field edges on all four
sides (XI ,X2,YI, Y2) as shown in Fig. 4.
l Determine the total deviations in the X and Y direction (ignore the +/- signs).
l Both the length deviation (Z Y) and the width deviation (C X) must be less than 1.6 cm.
Fig. 5 Fig. 6
l If the deviation is higher, loosen the 4 Allen screws slightly (arrows/Fig. S/Fig. 6) and
move the collimator accordingly.
Then, tighten the screws at the collimator (arrows/Fig. 5/Fig. 6) again.
l Repeat the check and, if necessary, adjust the collimator again until the deviation
between the light field and the radiation field is within the admissible tolerance
(<1,6cm).
Fig. 7 Fig. 8
06
Fig. 9 Fig. 10
Fig. 1
Fig. 2 Fig. 3
l Attach the new collimator, fasten it with the four screws (arrows /Fig. 2/Fig. 3) and center
it.
l Connect the connecting cables and screw down the rear panel.
l Check agreement of light and radiation field and make adjustment if required
(see “Agreement of light and radiation field”).
Fig. 4 Fig. 5
(II Do not touch the glass envelope with your bare fingers.
Fig. 6
Fig. 7
TD RX 61 Friedrich
TD RX 1 / Kern FL
TDU 3 / Hay