Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
and rigidity of LYSAGHT TRIMDEK permits and COLORBOND ULTRA® finish is intended for
wide support spacings to be used with severe coastal or industrial environments.
safety. Refer to maximum support Minimum roof pitch
spacings listed on page 2. House Framing Solutions
Long lengths and a special anti-capillary
Simple, low-cost fixing groove in the side lap allow you to use
Long, straight lengths of LYSAGHT TRIMDEK LYSAGHT TRIMDEK on roof pitches as low as
can be lowered into place and aligned 2 degrees (1 in 30). Customer Support
29 mm
762 mm cover
2
p
s if end la
End spannsion joint
or expa eeting O ES
IS
in sh IS IS ES O
IC
LON
O -CYC
LAT
NON AREA
ES IS IS ES
Spacing definitions 27°S
ES = End span
IS = Internal span Single
O = Overhang span
O
LYSAGHT TRIMDEK offers the full benefits of If this product is to be used in marine, For cutting thin metal on site,
the latest methods for modelling wind severe industrial, or unusually corrosive we recommend a circular saw with a
pressures. The Wind pressure capacity environments, ask for advice from our metal-cutting blade because it produces
table is determined by full scale tests information line. fewer damaging hot metal particles and
conducted at BLUESCOPE LYSAGHT’s NATA- leaves less resultant burr than a
Metal & timber compatibility
registered testing laboratory, using the carborundum disc.
direct pressure-testing rig. Lead, copper, bare steel and green or
Cut materials over the ground and not
some chemically-treated timbers are not
Testing was conducted in accordance over other materials.
compatible with this product; thus don’t
with AS 1562.1—1992 Design and
allow any contact of the product with Sweep all metallic swarf and other
Installation of Sheet Roof and Wall
those materials, nor discharge of debris from roof areas and gutters at the
Cladding—Metal, and AS 4040.2—1992
rainwater from them onto the product. If end of each day and at the completion
Resistance to Wind Pressures for Non-
there are doubts about the compatibility of the installation. Failure to do so can
cyclonic Regions.
of products being used, ask for advice lead to surface staining when the metal
The pressure capacities for serviceability from our information line. particles rust.
are based on a deflection limit of
Maintenance Sealed joints
(span/120) + (maximum fastener
pitch/30). Optimum product life will be achieved For sealed joints use screws or rivets and
if all external surfaces are washed neutral-cure silicone sealant branded as
The pressure capacities for strength
regularly. Areas not cleaned by natural suitable for use with galvanised or
have been determined by testing the
rainfall (such as the tops of walls ZINCALUME® steel.
cladding to failure (ultimate capacity).
sheltered by eaves) should be washed
These pressures are applicable when Non-cyclonic areas
down every six months.
the cladding is fixed to a minimum
The information in this brochure is
of 1.0 mm, G550 steel. Storage and handling
suitable for use only in areas where a
For material less than 1.0 mm thick, seek Keep the product dry and clear of the tropical cyclone is unlikely to occur as
advice from our information line. ground. If stacked or bundled product defined in AS 1170.2—1989 SAA Loading
becomes wet, separate it, wipe it with a Code, Part 2: Wind Loads.
clean cloth and stack it to dry thoroughly.
Ask for advice from our information
Handle materials carefully to avoid service on designs to be used in
damage: don’t drag materials over rough cyclonic areas.
surfaces or each other; carry tools, don’t
drag them; protect from swarf.
3
Installation
Fasteners without insulation
Fixing to steel Fixing to steel Fixing to timber
up to 0.75 mm BMT 0.75 to 3 mm BMT
Metal Batten Teks screws Type 17 screws
13-13 x 55 Metal Teks screws with hex. washer-head,
OR
Crest Type 17 screws with hex. washer-head, EPDM seal,
fixed with hex. washer-head, EPDM seal, Higrip & Shankguard
EPDM seal, Higrip & Shankguard
Higrip & Shankguard 12-14 x 45 SOFTWOOD: 12-11 x 65
HARDWOOD: 12-11 X 50
12-11 x 50
Type 17 screws
with hex. washer-head
& EPDM seal Metal Teks screws Type 17 screws
Valley 10-12 x 20 with hex. washer-head with hex. washer-head
fixed OR
& EPDM seal & EPDM seal
Metal Teks screws 10-16 x 16 SOFTWOOD: 10-12 x 30
with hex. washer-head SOFTWOOD: 10-12 x 20
& EPDM seal
10-16 x 16
End lapping
End-laps are not usually necessary
because TRIMDEK is available in
long lengths.
TRIMDEK
Crest fixing for roofs or walls
Crest: 4 fasteners†
S
Valley: 4 fasteners†
4
The perfect
finishing touch
LYSAGHT rainwater goods
Novaline fascia
Whether you're renovating a classic
Australian house or searching for a
distinctive look for a new home, add the
perfect finishing touch to your TRIMDEK roof
with our extensive range of rainwater Trimline
goods. LYSAGHT rainwater goods provide
the perfect finishing touch.
5
LYSAGHT TRIMDEK
design advantages
• Smart appearance with subtle
square fluting
• Simple, low cost fixing so TRIMDEK is
economical to install
• Available in a range of COLORBOND®
steel colours
• Can be used on pitches as low as 2º
• High tensile steel means design freedom
with longer spans and wider spreads