Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
PARTS MANUAL
This manual has been prepared for and is considered part of -
16007018
Serial Number
NOTICE
The serial number of the crane and this attachment are the only method your Manitowoc distributor or the
factory has of providing you with correct parts and service information.
• The serial number of the crane is located on an identification plate attached to the operator’s cab.
• The serial number of this attachment is located on an identification plate attached to the boom cap.
Refer to the Nameplate and Decal Assembly Drawing in Section 3 of this manual for the exact location of
the identification plates.
Always furnish serial number of crane and attachment when ordering parts or discussing service
problems with your Manitowoc distributor or the factory.
ÿþýüûúùúø
2401 South 30th Street PO Box 70
11-12-09
Manitowoc, WI 54221-0070
Phone: 920-684-6621 Fax: 920-683-6278
COUNTERWEIGHT, SPECIAL
ASSEMBLY REVISION
81010340 A
1 of 6
Group A
Manitowoc
ASSEMBLY REVISION
81010340 A
2 of 6
Manitowoc Group A
ASSEMBLY REVISION
81010340 A
3 of 6
Group A
Manitowoc
ASSEMBLY REVISION
81010340 A
4 of 6
MODEL
16000
COUNTERWEIGHT, SPECIAL
16000 Wind Attachment
ITEM PART # QTY. DESCRIPTION OF PART
1 192495 16 BOX, Counterweight
2 7126211853 8 SCREW, Hex Cap (M12 x 1.75 - 55 mm long /8.8/ zinc)
3 7661210003 8 NUT, Hex (M12 x 1.75 /8/ zinc)
4 7951210210 8 WASHER, Lock High Collar (M12, zinc)
5 A04093 2 PIN, Hitch (1/2” dia x 4” long, w /hairpin cotter)
6 A10788 1 TRAY, Counterweight (see Note 3)
7 A12065 2 PIN, 1 Hole w/Hd (3-1/4” dia x 337 mm long)
8 A12069 1 ROD, Threaded (7/8 -14UNF-2A x 509 mm both ends)
9 A12166 4 PENDANT (3/4” dia x 22‘ long)
10 A12167 4 BRACKET, Cylinder Stop
11 A12175 1 CYLINDER, Hydraulic (2” bore x 25” stroke) (0-1323)
12 178098 1 CLAMP, Channel Anchor (1” DP x 3” long)
13 345684 2 CLAMP, Tube (5/8” dia)
14 375445 1 COUPLER
15 375446 1 NIPPLE, Quick Disconnect
16 428223 2 FITTING, Adapter Straight (6 ORFS x 6 ORB)
17 428224 2 FITTING, Adapter Straight (6 ORFS x 8 ORB)
18 A12758 1 HOSE ASSEMBLY (3/8” ID x 150” long)
19 A12758 1 HOSE ASSEMBLY (3/8” ID x 150” long)
20 A08931 2 BOX, Counterweight
21 564094 4 PIN, Wire Rope Socket
22 A17282 4 PLATE, Adapter Counterweight Raising
Note 1: Lifting lugs on the individual components are intended to handle only that component.
Note 2: NEVER-SEEZ
Apply NEVER-SEEZ or equivalent to the following:
All threaded surfaces except those treated with LOCTITE.
All bores.
All pins.
Note 3: COUNTERWEIGHT ASSEMBLY WEIGHT
ASSEMBLY REVISION
0-1323
ASSEMBLY REVISION
6 of 6
Manitowoc Group A
ASSEMBLY REVISION
Eng Rev
12-20-10 A12868 AC
1 of 17
Group A
Manitowoc
ASSEMBLY REVISION
A12868 AC
2 of 17
Manitowoc Group A
ASSEMBLY REVISION
A12868 AC
3 of 17
Group A
Manitowoc
ASSEMBLY REVISION
A12868 AC
4 of 17
MODEL
16000
6 of 17
MODEL
16000
8 of 17
MODEL
16000
ASSEMBLY REVISION
10 of 17
MODEL
16000
12 of 17
MODEL
16000
14 of 17
MODEL
16000
Note 3: Refer to boom and jib rigging drawing for part number.
Note 4: Not Shown - See 175916 for quantities and placement.
Note 5: Past production.
Note 6: Emission tag supplied by Cummins and installed by MCC after final painting of cab.
Note 7: Align arrow on decal with hole in strut.
ASSEMBLY REVISION
16 of 17
MODEL
16000
ASSEMBLY REVISION
BOOM, #58WA
05-13-10 81009833 F
1 of 12
Group F
Manitowoc
81009833 F 05-13-10
2 of 12
Manitowoc Group F
05-13-10 81009833 F
3 of 12
Group F
Manitowoc
81009833 F 05-13-10
4 of 12
Manitowoc Group F
05-13-10 81009833 F
5 of 12
Group F
Manitowoc
81009833 F 05-13-10
6 of 12
Manitowoc Group F
05-13-10 81009833 F
7 of 12
Group F
Manitowoc
81009833 F 05-13-10
8 of 12
Manitowoc Group F
05-13-10 81009833 F
9 of 12
MODEL
16000
BOOM, #58WA
ITEM PART # QTY. DESCRIPTION OF PART
1 A10882 1 BUTT ASSEMBLY, #58 (8 meter) (see Note 10)
2 A10919 2 STRAP, #58 Boom
3 A11396 1 INSERT TRANSITION ASSEMBLY, #58 (5 meter) (see Note 11)
4 A11543 1 INSERT ASSEMBLY, #58 w/ Auxiliary Sheaves (12 meter) (see Note 12)
5 A14925 6 COLLAR
6 A14926 6 PIN, 1 Hole with Head
7 A14929 6 PIN, 2 Holes
8 A12944 2 PIN, 1 Hole with Head
9 A12945 2 COLLAR
10 A12946 2 PIN, 2 Holes
11 81009868 1 TOP ASSEMBLY, #58WA (1 meter cap)
12 81009978 1 BOOM POINT UPPER ASSEMBLY, Extended #58WA Boom
13 81011854 4 LINK, #58WA Boom Cap
14 81010227 2 STRAP, #58WA Boom
15 A14907 4 LINK, #58 Boom Strap
16 A13178 2 SHIM
17 A15521 2 SHIM
18 A15522 2 SHIM
19 81010676 4 LINK, #58WA Boom Strap
21 81007957 1 BOX, Parts For Part Storage (see Note 17)
22 81010424 2 PIN, 1 Hole w/ Hd
23 81011868 2 BRACKET, Strap
24 A11795 2 PIN, 2 Hole
25 562085 2 PIN, Cotter
NO. REQD. FOR THE FOLLOWING ITEMS ARE IN TABLES
100 562085 PIN, Cotter
101 563640 PIN, Safety (see Note 8)
102 A10918 STRAP, #58 Boom
103 A10920 STRAP, #58 Boom
104 A11539 LINK, #58 Boom Strap (see Note 8)
105 A11798 PIN, 1 Hole w/ Hd
106 A11799 PIN, 2 Holes
107 A11800 COLLAR
108 A13294 PIN, 1 Hole with Head (see Note 8)
109 81011915 INSERT ASSEMBLY, #58 Heavy (12 meter) (see Note 15)
110 81009834 INSERT ASSEMBLY, #58 Heavy (6 meter) (see Note 5)
111 81009839 INSERT ASSEMBLY, #58 Heavy (3 meter) (see Note 6)
112 81009924 STRAP, #58 Boom
114 81009986 BOOM ASSEMBLY, #58WA Intermediate Suspension (see Note 1, 18)
OPTIONAL PARTS
200 A13737 1 HOOK AND WEIGHT BALL ASSEMBLY (18 MT - 20 US) (0-1363)
201 236503 1 HOOK BLOCK ASSEMBLY (41 MT - 45 US) (see Note 9) (0-1230)
202 A13155 1 HOOK BLOCK ASSEMBLY (226 MT - 250 US) (0-1358)
203 A13154 1 HOOK BLOCK ASSEMBLY (100 MT - 110 US) (0-1390)
204 A14824 1 HOOK BLOCK ASSEMBLY (181 MT - 200 US) (0-1377)
205 A13170 1 BOOM ASSEMBLY, #58 Ladder Storage
206 A15927 1 BLOCK (100 MT, 28 mm rope) (0-1408)
207 A17740 1 BLOCK (100 MT, 3 sheave) (0-1454)
208 A15946 1 BOOM POINT UPPER ASSEMBLY, Extended (see Note 20)
209 81007437 1 HOOK BLOCK ASSEMBLY, Duplex (180 MT-200 US) (0-1373)
210 A10888 1 DRUM ASSEMBLY, Luffing/Auxiliary (see Note 19)
211 A13917 1 PAWL ASSEMBLY, Luffing Drum (see Note 19)
ASSEMBLY REVISION
10 of 12
MODEL
16000
BOOM, #58WA
ITEM PART # QTY. DESCRIPTION OF PART
212 A11946 1 GUIDE WIRE ROPE ASSEMBLY, Luffing/Auxiliary Line (see Note 19)
Note 1: 71 m (232.9 ft) through 92 m (301.8 ft) boom requires intermediate suspension item 114.
Note 2: Maximum number of 6 meter inserts = 1.
Maximum number of 3 meter inserts = 1.
Note 3: After 12 meter insert w/ auxiliary sheaves, insert assemblies must be installed in ascending
length.
Note 4: See sheets 3, 4, 5 for boom makeup.
Note 5: See note 2 and note 3 and note 13.
Note 6: See note 2 and note 3 and note 14.
Note 7: All luffing jib and backstay straps, links and pins stowed with inserts must be removed for use
with this assembly.
Note 8: Items 100, 105, 106, and 107 quantities include items that are stowed when intermediate
suspension is used.
Note 9: Use for 2 part line on upper boom point. also used for machine assembly with 9.75 m (32 ft)
live mast.
Note 10:Butt 8 meter ID tag A10883 or 81006893.
Note 11:Insert 5 meter transition ID tag A11352 or 81005868 or 81006897.
Note 12:Insert 12 meter w/ auxiliary sheaves (heavy) ID tag A11544 or A17834 or 81006890.
Note 13:Insert 6 meter (heavy) ID tag 81009835 or 81010114.
Note 14:Insert 3 meter (heavy) ID tag 81009840 or 81010111.
Note 15:Insert 12 meter (heavy) ID tag 81011916 or 81011870.
Note 17:81007957 to be shipped as a loose item containing parts for the extended upper point and
intermediate suspension.
Note 19:Items 210, 211 and 212 are to be used for the auxiliary drum option.
Note 20:Boom point upper assembly A15946 can only be used with 34.25° offset angle.
Note 21:Insert 12M assembly #58 (Heavy) A14543 with ID Tag #14544 , may be used in place of
insert 12m assembly #58 (Heavy) 81011915 at location adjacent to transition insert (item 3).
Note 22:Insert assembly #58 12M with equalizer rails 81011592 with Tag #81011593 or 81011594
CANNOT be used on the 71 M #58WA Boom.
Note 23:Insert assembly #58 12M with equalizer rails 81011592 with Tag #81011593 or 81011594
may be used in place of insert 12M assembly #58 (heavy) 81011915 as first 12 M insert after
12M insert assembly wtih auxilliary sheaves item 14 (81010227).
Note 24:Boom Handling with Mast.
Note 25:Short Strut Configuration: 83m, 86m 89m & 92m Boom.
Note 26:Long Strut Configuration 71m, 74m, 77m, & 80m Boom.
Note 27:Boom Closing
Note 28:Strap Hookup
ASSEMBLY REVISION
ASSEMBLY REVISION
12 of 12
Manitowoc Group F
ASSEMBLY REVISION
81009834 B
1 of 3
Group F
Manitowoc
ASSEMBLY REVISION
81009834 B
2 of 3
MODEL
16000
INSERT 6M
#58 (Heavy)
ITEM PART # QTY. DESCRIPTION OF PART
1 562045 16 PIN, Cotter (1/8” dia x 1-1/2” long)
2 562172 2 PIN, Cotter (1/2” dia x 4” long)
3 81010114 1 INSERT, 6m #58 (Heavy) (0-577)
4 7126192850 4 BOLT, Hex (M10 x 1.5 - 120 mm long /8.8/ zinc)
5 7661190803 4 NUT, Lock (M10 x 1.5, zinc)
6 7951190014 8 WASHER, Flat (M10, zinc)
7 A10937 1 TIMBER (1480 mm x 89 mm x 89 mm)
8 A11537 4 LINK, Strap Stowage
9 A11538 4 LINK, Strap Stowage
10 A11795 8 PIN, 2 Holes (19 mm dia x 132 mm long)
11 A16075 2 GUARD, Wire Rope 10 GA (9/64” thick)
12 A16534 2 PIN, 1 Hole w/Hd (63.50 mm dia x 172.4 mm long)
ITEMS FROM BOOM ASSEMBLY TO BE SHIPPED WITH THE 6M HEAVY INSERT ASSEMBLY AS REFERENCE ITEMS
100 562085 8 PIN, Cotter (3/16” dia x 1-1/2” long)
101 563640 2 PIN, Safety (1/4” OD x 5” long)
102 A10918 2 STRAP, 6 m #58 Boom
103 A11539 4 LINK, #58 Boom Strap
104 A11798 4 PIN, 1 Hole w/Hd (65 mm dia x 92 mm long)
105 A11799 4 PIN, 2 Holes (12.7 mm dia x 93 mm long)
106 A11800 4 COLLAR (66 mm ID)
107 A13294 2 PIN, 1 Hole w/Hd (75.80 mm dia x 160.4 mm long)
INSERT 6M #58 MACHINING
200 81009835 1 INSERT, 6m #58 (Heavy) (0-577)
Note 2: Attach timbers so they are free to slide under thermal expansion/contraction of plastic.
0-577
ASSEMBLY REVISION
ASSEMBLY REVISION
81009839 B
1 of 3
Group F
Manitowoc
ASSEMBLY REVISION
81009839 B
2 of 3
MODEL
16000
INSERT 3M
#58 Boom (Heavy)
ITEM PART # QTY. DESCRIPTION OF PART
1 562045 16 PIN, Cotter (1/8” dia x 1-1/2” long)
2 562172 2 PIN, Cotter (1/2” dia x 4” long)
3 81010111 1 INSERT, 3m #58 Boom (Heavy) (0-577)
4 7126192850 4 BOLT, Hex (M10 x 1.5 - 120 mm long /8.8/ zinc) (see Note 2)
5 7661190803 4 NUT, Lock (M10 x 1.5, zinc) (see Note 2)
6 7951190014 8 WASHER, Flat (M10, zinc) (see Note 2)
7 A10937 1 TIMBER (1480 mm x 89 mm x 89 mm) (see Note 2)
8 A11537 4 LINK, Strap Stowage
9 A11538 4 LINK, Strap Stowage
10 A11795 8 PIN, 2 Holes (19 mm dia x 132 mm long)
11 A16075 2 GUARD, Wire Rope 10 GA (9/64” thick)
12 A16534 2 PIN, 1 Hole w/Hd (63.50 mm dia x 172.4 mm long)
ITEMS FROM MAIN BOOM ASSEMBLY TO BE SHIPPED WITH THE 3M INSERT ASSEMBLY AS REF. ITEMS
100 562085 8 PIN, Cotter (3/16” dia x 1-1/2” long)
101 563640 2 PIN, Safety (1/4” OD x 5” long)
102 81009924 2 STRAP, 3 m #58 Boom (see Note 1)
103 A11539 4 LINK, #58 Boom Strap
104 A11798 4 PIN, 1 Hole w/Hd (65 mm dia x 92 mm long)
105 A11799 4 PIN, 2 Holes (12.7 mm dia x 93 mm long)
106 A11800 4 COLLAR (66 mm ID)
107 A13294 2 PIN, 1 Hole w/Hd (75.80 mm dia x 160.4 mm long)
INSERT 3M #58 BOOM MACHINING
200 81009840 1 INSERT, 3m #58 Boom (Heavy) (0-577)
ASSEMBLY REVISION
ASSEMBLY REVISION
81009868 C
1 of 3
Group F
Manitowoc
ASSEMBLY REVISION
81009868 C
2 of 3
MODEL
16000
TOP, #58WA CAP (1 M)
ITEM PART # QTY. DESCRIPTION OF PART
1 562045 16 PIN, Cotter
2 562152 8 PIN, Cotter
3 563640 2 PIN, Safety
4 563790 4 PIN, Hair Cotter
5 563875 4 PIN, Hitch
6 81009869 1 TOP, #58WA Cap
7 81010355 2 STRUT, Wire Rope Guide
8 81010425 2 PIN, 1 Hole w/Hd
9 81010460 2 PIN, 2 Holes
10 81010461 4 LINK, Strap Stowage
11 81010462 4 PIN, 2 Holes
12 A06905 4 COLLAR\
13 A11795 4 PIN, 2 Holes
14 A12785 1 GUIDE WIRE ROPE ASSEMBLY
15 A12829 4 PIN, 2 Holes
16 A13741 2 PIN, 2 Holes
SHIPMENT ITTEMS: ITEMS FROM #58WA BOOM ASSEMBLY TO BE SHIPPED WITH THE TOP ASSEMBY AS REFERENECE
ITEMS (SEE NOTE 3)
100 562085 12 PIN, Cotter
101 563640 2 PIN, Safety
102 81011854 4 LINK, #58 Boom Cap
103 81010227 2 STRAP, #58WA Boom
104 81010424 2 PIN, 1 Hole with Head
105 81010676 4 LINK, #58WA Boom Strap
106 A12944 2 PIN, 1 Hole with Head
107 A12945 2 COLLAR
108 A12946 2 PIN, 2 Holes
109 A14925 4 COLLAR
110 A14926 4 PIN, 1 Hole w/Hd
111 A14929 4 PIN, 2 Holes
112 562045 4 PIN, Cotter
113 81011868 2 BRACKET, Strap
114 A11795 2 PIN, 2 Holes
ASSEMBLY REVISION
ASSEMBLY REVISION
81009978 B
2 of 10
Manitowoc Group F
ASSEMBLY REVISION
81009978 B
3 of 10
Group F
Manitowoc
ASSEMBLY REVISION
81009978 B
4 of 10
Manitowoc Group F
ASSEMBLY REVISION
81009978 B
5 of 10
Group F
Manitowoc
ASSEMBLY REVISION
81009978 B
6 of 10
MODEL
16000
BOOM POINT UPPER, EXTENDED #58WA BOOM
ITEM PART # QTY. DESCRIPTION OF PART
1 169810 2 PLATE, Keeper (1/2” thick)
2 169837 1 SPACER
3 170677 1 SPACER (6-1/2” OD x 4-1/2” ID x 13/16”)
4 172104 2 BUSHING (3-1/2” ID x 4-1/2” OD x 3” long)
5 174213 1 SHAFT
6 225100 1 WASHER, Bearing Lock Timken (#TW140)
7 225105 2 NUT, Bearing Lock (AN-24)
8 225111 1 WASHER, Bearing Lock (#24 bore)
9 429000 2 FITTING, Grease (1/8” NPT)
10 554175 2 PAD, Bearing
11 562150 2 PIN, Cotter (3/8” dia x 3” long)
12 562175 16 PIN, Cotter (1/2” dia x 7" long plated)
13 563803 4 PIN, Wire Lock (3/8” dia x 2-1/4” long)
14 563823 4 PIN, Wire Lock (1/4” dia x 1-3/4” long)
15 602161 2 ROLLER (4-1/2” ID x 39” OD x 2-3/4” wide)
16 602171 3 ROLLER (2-1/32” ID x 4” OD)
17 612717 6 SCREW, Cap Hex (3/4 -10UNC x 1-3/4” long - grade 5)
18 614041 2 SCREW, Cap Socket Flat (1/2” -13UNC x 1-1/4” long - grade 8)
19 710308 6 WASHER, Lock (3/4”)
20 81009979 1 FRAME, Boom Point Upper (7.6 m)
21 81010191 1 GUARD, Wire Rope (50.8 mm dia x 788 mm long)
22 81010193 1 GUARD, Wire Rope (50.8 mm OD x 38.1 mm ID x 500 mm long)
23 81010194 1 SHAFT
24 81010195 2 SPACER, Tube (8-3/4” OD x 8-1/64” ID x 6-47/64” long)
25 81010388 2 LINK, Connecting
26 81010390 8 PIN, 2 Hole (127 mm dia x 246.5 mm long)
27 7126191353 4 SCREW, Cap Hex (M10 x 1.5 - 30 mm long /8.8/ zinc)
28 7126271653 4 SCREW, Cap Hex (M20 x 2.5 - 45 mm long /8.8/ zinc)
29 7951190014 4 WASHER, Flat (M10, zinc)
30 7951190210 4 WASHER, Lock High Collar (M10, zinc)
31 7951270210 4 WASHER, Lock High Collar (M20, zinc)
32 A01427 2 NUT, Bearing Lock Timken (#TAN-140)
33 A01670 1 PLATE, Keeper (1/2” thick)
34 A01671 1 SLEEVE
35 A01672 2 PLATE, Keeper
36 A14182 2 GUARD, Wire Rope (31.75 mm OD x 6.35 mm wall x 146 mm long)
37 A16057 1 BRACKET
38 A16203 2 LINK, Connecting
40 A16372 1 GUARD, Wire Rope (2” OD x 1-1/2” ID x 37-1/2” long)
41 81008829 2 SIGN, Boom Manitowoc (see Note 6)
42 7121171301 32 SCREW (M8 x 30 mm long /4.8/ PLT zinc) (see Note 6)
43 7661170004 32 NUT, Hex (M8 x 1.25 /10/ PLN) (see Note 6)
44 7951170210 32 WASHER, Lock High Collar (M8, zinc) (see Note 6)
OPTION 1: 16000 W/ 28MM BUTTON SOCKET & SEALED SHEAVES
100 a10670 1 PIN, 1 Hole w/Hd (2-1/4” dia x 3-1/2” long)
101 141707 1 PIN, 2 Holes (2-1/4” dia x 6-23/64” long)
102 171250 1 SHEAVE WIRE ROPE ASSEMBLY (1-1/8” dia rope)
103 179194 2 PIN, 2 Holes (1/2” dia x 3-23/32” long)
104 179195 1 COLLAR (3-1/2” dia x 1” long)
105 179862 1 COLLAR (3” dia x 1” long)
106 196061 2 LINK
107 196062 1 PIN
ASSEMBLY REVISION
ASSEMBLY REVISION
8 of 10
MODEL
16000
BOOM POINT UPPER, EXTENDED #58WA BOOM
ITEM PART # QTY. DESCRIPTION OF PART
OPTION 5: 18000 W/ 32MM WEDGE SOCKET & SEALED SHEAVES
300 141707 1 PIN, 2 Holes (2-1/4” dia x 6-23/64” long)
301 163064 4 PIN, 1 Hole w/Hd (3” dia x 5-9/16” long)
302 171250 1 SHEAVE WIRE ROPE ASSEMBLY (1-1/8” dia rope)
303 562170 2 PIN, Cotter (1/2” dia x 3” long)
304 562174 5 PIN, Cotter (1/2” dia x 4-1/2” long)
305 631524 3 SHEAVE WIRE ROPE ASSEMBLY (0-486)
306 646247 1 WEDGE, Socket (0-890)
307 81010515 2 LINK
308 A10670 1 PIN, 1 Hole w/Hd (2-1/4” dia x 4-1/64” long)
309 A15281 1 WEDGE, Socket (0-890)
310 A16209 2 SPACER, Tube (8-49/64” OD x 8-1/64” ID x 1-7/8” long)
311 A16308 1 LINK
312 A16464 1 LINK
350 141707 1 PIN, 2 Holes (2-1/4” dia x 6-23/64” long)
351 163064 4 PIN, 1 Hole w/Hd (3” dia x 5-9/16” long)
352 562170 2 PIN, Cotter (1/2” dia x 3” long)
353 562174 5 PIN, Cotter (1/2” dia x 4-1/2” long)
354 646247 1 WEDGE, Socket (0-890)
355 81006219 1 SHEAVE WIRE ROPE ASSEMBLY (1-1/8” wire rope)
356 81006224 3 SHEAVE WIRE ROPE ASSEMBLY (1-1/4” rope x 30” OD x 8” ID)
357 81010515 2 LINK
358 A10670 1 PIN, 1 Hole w/Hd (2-1/4” dia x 4-1/64” long)
359 A15281 1 WEDGE, Socket (0-890)
360 A16209 2 SPACER, Tube (8-49/64” OD x 8-1/64” ID x 1-7/8” long)
361 A16308 1 LINK
362 A16464 1 LINK
OPTION 7: 18000 W/ 32MM BUTTON SOCKET & SEALED SHEAVES
400 141707 1 PIN, 2 Holes (2-1/4” dia x 6-23/64” long)
401 163064 3 PIN, 1 Hole w/Hd (3” dia x 5-9/64” long)
402 171250 1 SHEAVE WIRE ROPE ASSEMBLY (1-1/8” dia rope)
403 562170 2 PIN, Cotter (1/2” dia x 3” long)
404 562174 4 PIN, Cotter (1/2” dia x 4-1/2” long)
405 631524 3 SHEAVE WIRE ROPE ASSEMBLY (0-486)
406 646247 1 WEDGE, Socket (0-890)
407 81010515 2 LINK
408 A06278 1 SOCKET, Button Wire With Pin (for 28 mm or 32 mm) (0-1647)
409 A08286 1 BUSHING (3” OD x 2-21/64” ID x 2-3/8” long)
410 A10670 1 PIN, 1 Hole w/Hd (2-1/4” dia x 4-1/64” long)
411 A16209 2 SPACER, Tube (8-49/64” OD x 8-1/64” ID x 1-7/8” long)
412 A16308 1 LINK
OPTION 8: 18000 W/ 32MM BUTTON SOCKET & GREASED SHEAVES
450 141707 1 PIN, 2 Holes (2-1/4” dia x 6-23/64” long)
451 163064 3 PIN, 1 Hole w/Hd (3” dia x 5-9/16” long)
452 562170 2 PIN, Cotter (1/2” dia x 3” long)
453 562174 4 PIN, Cotter (1/2” dia x 4-1/2” long)
454 646247 1 WEDGE, Socket (0-890)
455 81006219 1 SHEAVE WIRE ROPE ASSEMBLY (1-1/8” wire rope)
456 81006224 3 SHEAVE WIRE ROPE ASSEMBLY (1-1/4” rope x 30” OD x 8” ID)
457 81010515 2 LINK
458 A06278 1 SOCKET, Button Wire Rope With Pin (for 28 mm or 32 mm) (0-1647)
459 A08286 1 BUSHING (3” OD x 2-21/64” ID x 23/8” long)
ASSEMBLY REVISION
Step:2.
Attach equal length slings or chains to the forward lifting lugs on the extended upper boom point and the lifting lugs on the
boom cap. The main boom should be blocked up at least 300 mm (12”). Lift the extended upper boom point and boom
cap and position it above the transition insert so that the upper connector pins of the boom cap line up with the upper
connector hooks of the transition insert.
Step:3.
Lower the extended upper boom point and boom cap until the lower connector pin holes of the boom cap are aligned with
the holes in the transition insert. Insert lower connector pins. Unhook slings from the boom cap. Lift up on the extended
upper boom point to unload shipping pin. Remove shipping pin and store it on the boom cap. Lower extended upper
boom point to the ground.
Step:2.
Attach equal length slings or chains to lifting lugs on the extended upper boom point. The main boom should be blocked
up at least 300 mm (12”). Lift the extended upper boom point and position it above the main boom so that connecting
links item 25 can be pinned to the main boom. Position links as shown and pin both sides. Extended upper boom point
should be in a horizontal position during this procedure.
Step:3.
After attaching top pins, lower the extended upper boom point until the lower pins are aligned with the holes in the main
boom. Pin extended upper boom point to main boom on both sides.
ASSEMBLY REVISION
10 of 10
Group F
cowotinaM
BOOM, #58WA INTERMEDIATE STRUTBOOM
ASSEMBLY REVISION
81009986 D
1 of 2
MODEL
16000
BOOM, #58 INTERMEDIATE STRUT
ITEM PART # QTY. DESCRIPTION OF PART
1 562044 2 PIN, Cotter (1/8” dia x 1-1/4” long)
3 562110 2 PIN, Cotter (1/4” dia x 3” long)
4 563790 2 PIN, Hair Cotter
5 81009987 1 BEAM, #58WA Intermediate Strut
6 81010258 2 BRACKET, Intermediate Strut Support
7 81010269 2 LATCH, #58WA Intermediate Strut
8 81010285 2 PIN , 1 Hole w/Hd (15.9 mm dia x 75 mm long)
9 81010286 2 PIN, Hitch (15.9 mm dia x 75 mm long)
10 81011871 2 PIN, Hitch (28.6 mm dia x 135 mm long)
11 81010443 2 PIN, 1 Hole w/Hd (65 mm dia x 116 mm long)
12 81010714 1 STRUT, #58WA Intermediate
81010259 1 Strut Weldment #58 Intermediate Upper
81010260 1 Strut Weldment #58 Intermediate Lower
13 A04830 2 PIN, Cotter 1 hole w/Hd (1-1/8” dia x 3” long)
14 A05786 2 PIN, Hair Cotter
17 562105 2 PIN, Cotter (3/16” dia x 1-1/2” long)
18 81013272 2 PIN, 1Holes (19 mm dia x 132 mm long)
Note 1: Rigging position - item 10 (81010287) through the top hole of outer tube and through hole in
inner tube of item 12 (81010714).
Note 2: Short strut - item 10 (81010287) through the middle hole of outer tube and hole in inner tube
of item 12 (81010714).
Note 3: Long strut - item 10 (81010287 through the bottom hole of outer tube and hole in inner tube of
item 12 (81010714).
Note 4: See boom rigging assembly for installation instructions.
ASSEMBLY REVISION
2 of 2
Manitowoc Group F
BRACKET, TRANSCEIVER
ASSEMBLY REVISION
81011005 B
1 of 2
MODEL
16000
BRACKET, TRANSCEIVER
ITEM PART # QTY. DESCRIPTION OF PART
1 81002169 1 CLAMP (4-1/2” ID tube)
2 81011031 1 ENCLOSURE, Transceiver Receptacle
3 81011033 1 BRACKET, Transceiver
4 7951130210 4 WASHER, Lock High Collar (M5, zinc)
5 A03311 1 STRIP, Trim Black Clean
6 A20020 4 SCREW, Slotted Pan Head (M5 x 12 mm long /4.8/ zinc)
ASSEMBLY REVISION
2 of 2
Manitowoc Group F
ASSEMBLY REVISION
81011915 A
1 of 3
Group F
Manitowoc
ASSEMBLY REVISION
81011915 A
2 of 3
MODEL
16000
INSERT
#58 12m Heavy
ITEM PART # QTY. DESCRIPTION OF PART
1 562045 16 PIN, Cotter (1/8” dia x 1-1/2” long)
2 562087 6 PIN, Cotter Plated (1/8”dia x 2” long)
3 562172 2 PIN, Cotter (1/2” dia x 4” long)
4 7126192850 8 BOLT, Hex (M10 x 1.5 - 120 mm long /8.8/ zinc) (see Note 2)
5 7661190803 8 NUT, Lock (M10 x 1.5, zinc) (see Note 2)
6 7951190014 16 WASHER, Flat (M10, zinc)
7 A06651 6 ROLLER
8 A06653 6 PIN, Cotter 1 Hole w/Hd (1” dia x 4” long)
9 A10937 2 TIMBER (148 mm x 89 mm x 89 mm) (see Note 2)
10 81011869 4 LINK, Strap Stowage
11 A11538 4 LINK, Strap Stowage
12 A11795 8 PIN, 2 Holes (19 mm dia x 132 mm long)
13 A16534 2 PIN, 1 Hole w/Hd (63.50 mm dia x 172.4 mm long)
14 81011916 1 INSERT, #58 12 m Heavy (see Note 3) (0-577)
15 A16075 4 GUARD, Wire Rope 10 GA (9/64” thick)
ITEMS FROM MAIN BOOM ASSEMBLY TO BE SHIPPED WITH THE 12.0 METER INSERT ASSEMBLY AS REF. ITEMS
100 562085 8 PIN, Cotter (3/16” dia x 1-1/2” long)
101 563640 2 PIN, Safety (1/4” OD x 5” long)
102 A10920 2 STRAP, #58 Boom 12 m (see Note 1)
103 A11539 4 LINK, #58 Boom Strap
104 A13294 2 PIN, 1 Hole w/Hd (75.80 mm dia x 160.4 mm long)
105 A11798 4 PIN, 1 Hole w/Hd (65 mm dia x 92 mm long)
106 A11799 4 PIN, 2 Holes (12.7 mm dia x 93 mm long)
107 A11800 4 COLLAR (66 mm ID)
ITEMS FROM LUFFING JIB ASSEMBLY TO BE SHIPPED WITH THE 12.0 METER INSERT ASSEMBLY AS REF. ITEMS
200 562085 8 PIN, Cotter (3/16” dia x 1-1/2” long)
201 A10920 2 STRAP, #58 Boom 12 m (see Note 1)
202 A11539 4 LINK, #58 Boom Strap
203 A11798 4 PIN, 1 Hole w/Hd (65 mm dia x 92 mm long)
204 A11799 4 PIN, 2 Holes (12.7 mm dia x 93 mm long)
205 A11800 4 COLLAR (66 mm ID)
LUFFING JIB PREP
300 562045 16 PIN, Cotter (1/8” dia x 1-1/2” long)
301 81011869 4 LINK, Strap Stowage
302 A11538 4 LINK, Strap Stowage
303 A11795 8 PIN, 2 Holes (19 mm dia x 132 mm long)
0-577
ASSEMBLY REVISION
Group F
1 of 14
ASSEMBLY REVISION
A10868 E
2 of 14
Manitowoc Group F
ASSEMBLY REVISION
A10868 E
3 of 14
Group F
Manitowoc
ASSEMBLY REVISION
A10868 E
4 of 14
Manitowoc Group F
ASSEMBLY REVISION
A10868 E
5 of 14
Group F
Manitowoc
ASSEMBLY REVISION
A10868 E
6 of 14
Manitowoc Group F
ASSEMBLY REVISION
A10868 E
7 of 14
Group F
Manitowoc
ASSEMBLY REVISION
A10868 E
8 of 14
Manitowoc Group F
ASSEMBLY REVISION
A10868 E
9 of 14
Group F
Manitowoc
ASSEMBLY REVISION
A10868 E
10 of 14
MODEL
16000
ELECTRIC CONTROL, BOOM WIRING AND LIMITS
ITEM PART # QTY. DESCRIPTION OF PART
1 345511 3 CLAMP, Tube (3/4” dia)
2 345512 6 CLAMP, Tube (1” dia)
3 510717 1 LOOM (13/32” ID x 20” long)
4 591121 1 CABLE, Reel Hand Crank
5 667007 24 STRAP, Tie-Wrap (7-3/4”)
6 667042 36 STRAP, Stay (8” max dia) (see Note 6)
7 669280 8 STUD, Wire Tie
8 A15368 1 TRANSCEIVER (2.4 GHz, 125K baud) (see Note 13)
10 A03415 1 CABLE, Electric Can Network WN20
12 A07389 1 CONTROLLER, Bus Interface Node (see Note 9)
13 A07484 1 CABLE, Electric (WNBE)
14 A16830 1 CABLE, Electric WBM390 Boom Cable Power
16 81000201 1 CABLE, Electric WBMJ8 Boom Jumper Cable Power (see Note 13)
17 81000200 1 CABLE, Electric Load Link
18 A15345 1 LOAD, Cell Link (35K wireless 2.4 GHz) (see Note 10)
19 A15487 1 LOAD, Cell Link (35K wired) (see Note 10)
20 A18332 8 WASHER, Lock External Tooth Countersunk (1/4”) (see Note 9)
21 7126151256 4 SCREW, Hex Serrated Flange (M6 x 25 mm long /8.8/ zinc) (see Note 9)
22 7126191453 4 SCREW, Hex Cap (M10 x 1.5 - 35 mm long /8.8/ zinc)
23 A18331 8 NUT, Keps (M6 x 1, zinc) (see Note 9)
24 7661190003 4 NUT, Hex (M10 x 1.5 /8/ zinc)
25 7951190220 4 WASHER, Lock (M10, zinc)
26 7126151453 4 SCREW, Hex Cap (M6 x 1 - 35 mm long /8.8/ zinc)
27 304639 1 CAP, Plug (size 20)
ADD FOR #58 BOOM TOP
50 334101 1 CHAIN, Straight Link (#5/0) (see Note 14)
51 142403 1 WEIGHT
52 195748 1 SWITCH ASSEMBLY, Block Up Limit
53 624633 1 SHACKLE, Anchor Loose Pin
54 667007 3 STRAP, Tie-Wrap (7-3/4”) (see Note 7)
55 669280 3 STUD, Wire Tie (see Note 7)
56 A02371 1 CABLE, Electric Block Up Limit
57 A08627 1 CONTROLLER, Boom Node (see Note 9)
58 A18332 4 WASHER, Lock External Tooth Countersunk (1/4”) (see Note 9)
59 7126151256 4 SCREW, Hex Serrated Flange (M6 x 25 mm long /8.8/ zinc) (see Note 9)
60 7126191453 3 SCREW, Hex Cap (M10 x 1.5 - 35 mm long /8.8/ zinc)
61 A18331 4 NUT, Keps (M6 x 1, zinc) (see Note 9)
62 7661190003 3 NUT, Hex (M10 x 1.5 /8/ zinc)
63 7951190220 3 WASHER, Lock (M10, zinc)
ADD FOR DRUM #1 (MAIN HOIST) WITH MINIMUM BAIL LIMITS
100 A15962 1 CABLE, Electric (W66)
ADD FOR DRUM #1 (MAIN HOIST) WITHOUT MINIMUM BAIL LIMITS
150 A16050 1 CABLE, Electric (W66)
ADD FOR DRUM #3 (BOOM MOUNTED LUFFING HOIST/AUX. DRUM) WITH MINIMUM BAIL LIMITS
200 A15961 1 CABLE, Electric (W63)
201 667007 12 STRAP, Tie-Wrap (7-3/4”)
202 669280 7 STUD, Wire Tie
ADD FOR DRUM #3 (BOOM MOUNTED LUFFING HOIST/AUX. DRUM) WITHOUT MINIMUM BAIL LIMITS
250 A16049 1 CABLE, Electric (W63)
251 667007 12 STRAP, Tie-Wrap (7-3/4”)
252 669280 7 STUD, Wire Tie
ASSEMBLY REVISION
12 of 14
MODEL
16000
ELECTRIC CONTROL, BOOM WIRING AND LIMITS
ITEM PART # QTY. DESCRIPTION OF PART
506 669280 6 STUD, Wire Tie (see Note 7)
507 A02371 1 CABLE, Electric Block Up Limit
508 A08628 1 CONTROLLER, Boom Node (see Note 9)
509 A15596 1 BRACKET, Wireless Receiver
510 709420 6 WASHER, Flat (1/4”, 3/64”, zinc)
511 A18332 4 WASHER, Lock External Tooth Countersunk (1/4”) (see Note 9)
512 7126151256 4 SCREW, Hex Serrated Flange (M6 x 25 mm long /8.8/ zinc) (see Note 9)
513 7126191453 3 SCREW, Hex Cap (M10 x 1.5 - 35 mm long /8.8/ zinc)
514 A18331 4 NUT, Keps (M6 x 1, zinc) (see Note 9)
515 7661190003 3 NUT, Hex (M10 x 1.5 /8/ zinc)
516 7951190220 3 WASHER, Lock (M10, zinc)
ADD FOR #59 LUFFING JIB OR #59 FIXED JIB
550 591117 1 CABLE, Reel Hand Crank
551 667042 24 STRAP, Stay (8” max dia) (see Note 6)
552 81000195 1 CABLE, Electric WBME18 Boom Cable Extension Power
553 A12050 1 CABLE, Electric WLJ280 Luffing Jib Cable Power
554 7126191453 4 SCREW, Hex Cap (M10 x 1.5 - 35 mm long /8.8/ zinc)
555 7661190003 4 NUT, Hex (M10 x 1.5 /8/ zinc)
556 7951190220 4 WASHER, Lock (M10, zinc)
ADD FOR #59 LUFFING JIB
600 A10866 1 JIB STOP ASSEMBLY, Automatic #59 Luffing Jib
ADD FOR #59 UPPER LUFFING JIB POINT (REF. 174211) OR #59 UPPER FIXED JIB POINT
(NEW CONSTRUCTION)
650 093657 1 BLOCK, Lift (for 1”, 1-1/8” , 1-1/4” wire rope)
651 162273 1 WEIGHT
652 168091 1 LUG
653 170120 1 BRACKET
654 174713 2 PLATE
655 195749 1 SWITCH ASSEMBLY, Block Up Limit
656 334101 2 CHAIN, Straight Link (#5/0) (see Note 14)
657 624633 3 SHACKLE, Anchor Loose Pin
658 667007 3 STRAP, Tie-Wrap (7-3/4”) (see Note 7)
659 669280 3 STUD, Wire Tie (see Note 7)
660 667042 3 STRAP, Stay (8” max dia)
661 81000193 1 CABLE, Electric Block Up Limit
662 7126191453 6 SCREW, Hex Cap (M10 x 1.5 - 35 mm long /8.8/ zinc)
663 7661190003 6 NUT, Hex (M10 x 1.5 /8/ zinc)
664 7951190220 6 WASHER, Lock (M10, zinc)
665 612453 4 SCREW, Hex Cap (3/8 -16UNC x 7/8” long - grade 5)
666 710304 4 WASHER, Lock (3/8”, zinc)
667 81011223 1 BRACKET
ADD FOR #58WA BOOM CAP WITH #58WA EXTENDED UPPER BOOM POINT
750 093657 1 BLOCK, Lift (for 1”, 1-1/8” , 1-1/4” wire rope)
751 142403 2 WEIGHT
752 162273 1 WEIGHT
753 168091 1 LUG
754 170120 1 BRACKET
755 174713 2 PLATE
756 195748 1 SWITCH ASSEMBLY, Block Up Limit
757 195749 1 SWITCH ASSEMBLY, Block Up Limit
758 334101 3 CHAIN, Straight Link (#5/0) (see Note 14)
759 477474 1 CABLE, Harness Extension Micro-Change (13 ft)
ASSEMBLY REVISION
Note 1: Block-up limit control is intended as a protective device. It is not to be used as a hoist
distance control for specific job applications.
Note 2: Periodic checks should be made to insure that block-up limit control is functioning properly.
Note 3: Caution: Block-up limit control system may not function at machines maximum single line
speed - carefully check each machine for maximum safe line speed.
Note 4: For blocks without actuator brackets see modification dwg 184433 customer furnished.
Note 5: When a locking swivel is placed in the wire rope dead end, allow extra length in chain equal
to length of the locking swivel added.
Note 6: Attach cable to boom top or jib by using straps at approximately 10 ft intervals.
Note 7: Attach cable to boom top or jib top between junction box and switch by using weld studs at
approximately 2 ft intervals.
Note 8: For receptacles equipped with shorting plugs:
Shorting plugs must be plugged in whenever receptacle is not being used.
Note 9: Electrical enclosures are to be mounted as shown in View M-M, View D-D and Detail N.
Torque the keps nuts (P/N A18331) tight to establish less than 0.1 ohms between the
machine’s frame and enclosure receptacle shells. All enclosure mounting screws must be
electrically common to each other (less than 0.1 ohms).
Note 10:The basic bill of material contains one wired load link (item 19) and one wireless load link
(item 18). The wired load link (item 19) is typically used on the lower point (even multi-parts of
line) and the wireless load link (item 18) is typically used on the upper point (single part line).
Note 11:The can system terminator must be plugged into the receptacle when cable is unplugged
from the receptacle.
Note 12:For crane wiring diagram, see diagram electrical system wiring A15613.
Note 13:Transceiver (item 8) and cable WBMJ8 (item 16) are mounted on the jib top for luffing jib or
fixed jib applications and #58WA boom cap for #58WA extended upper boom point
applications.
Note 14:9 feet long.
Note 15:Apply to threads Loctite #242 (MCC 622293).
Note 16:Strain relief must be looped over hook on receiver bracket.
ASSEMBLY REVISION
14 of 14
Manitowoc Group F
ASSEMBLY REVISION
A12785 F
1 of 3
Group F
Manitowoc
ASSEMBLY REVISION
A12785 F
2 of 3
MODEL
16000
WIRE ROPE GUIDE
ITEM PART # QTY. DESCRIPTION OF PART
2 562152 4 PIN, Cotter (3/8” x 4” long)
3 562154 2 PIN, Cotter (3/8” x 5” long)
4 7126271553 8 SCREW, Hex Cap (M20 x 2.5 - 40 mm long /8.8/ zinc)
5 7126271653 8 SCREW, Hex Cap (M20 x 2.5 - 45 mm long /8.8/ zinc)
6 7951270210 16 WASHER, Lock High Collr (M20, zinc)
7 A12752 2 PLATE, End (10 mm) (see Note 3)
8 A12812 1 GUIDE, Wire Rope
9 A12813 1 SHAFT (127 mm dia x 257 mm long)
10 A12814 1 SHAFT (127 mm dia x 307 mm long)
11 A12823 2 SPACER (146.2 OD x 127.1 ID x 31 mm long)
12 A12824 2 SPACER (146.2 OD x 127.1 ID x 91 mm long)
13 A12825 1 SPACER (159 OD x 127.1 ID x 43.6 mm long)
14 81008136 1 GUARD, Rope (50.8 OD x 6.35 W x 192 mm long)
15 A12828 1 GUARD, Rope (50.8 OD x 6.35 W x 239 mm long)
16 A12829 2 PIN, 2 Hole (63.5 dia x 83.5 mm long)
OPTION 1: WITHOUT LUFFING JIB PREPARATION WITH STANDARD SHEAVES
100 172082 1 TUBE, Spacer (5-46/64” OD x 5-1/64” ID x 3-11/16” long)
101 171250 2 SHEAVE ASSEMBLY (1-1/8” dia rope) (See Note 2 & 4) (0-1665)
OPTION 2: WITH LUFFING JIB PREPARATION WITH STANDARD SHEAVES (SEE NOTE 6)
200 562154 1 PIN, Cotter (3/8” dia x 5” long)
201 563880 1 PIN, Hitch (5/8” dia x 4” long)
202 A12816 1 SHAFT (49.3 mm dia x 186.5 mm long)
203 A12817 1 ROLLER (51.6 mm ID x 101.6 mm OD)
204 A12827 1 GUARD, Rope (50.8 OD x 6.35 W x 192 mm long
205 171964 1 SHEAVE ASSEMBLY (24 dia gr 1" rope) (See Note 2)
206 171250 2 SHEAVE ASSEMBLY (1-1/8” dia rope) (See Note 2 & 4) (0-1665)
OPTION 3: WITHOUT LUFFING JIB PREPARATION WITH MANUALLY GREASED SHEAVES
300 172082 1 TUBE, Spacer (5-46/64” OD x 5-1/64” ID x 3-11/16” long)
301 81006219 2 SHEAVE ASSEMBLY (1-1/8” dia rope) (See Note 2 & 5)
OPTION 4: WITH LUFFING JIB PREPARATION WITH MANUALLY GREASED SHEAVES (SEE NOTE 6)
400 562154 1 PIN, Cotter (3/8” dia x 5” long)
401 563880 1 PIN, Hitch (5/8” dia x 4” long)
402 A12816 1 SHAFT (49.3 mm dia x 186.5 mm long)
403 A12817 1 ROLLER (51.6 mm ID x 101.6 mm OD)
404 A12827 1 GUARD, Rope (50.8 OD x 6.35 W x 192 mm long
405 81007872 1 SHEAVE ASSEMBLY (24 dia gr 1" rope) (See Note 2) (0-1660)
406 81006219 2 SHEAVE ASSEMBLY (1-1/8” dia rope) (See Note 2 & 5)
Note 1: Apply NEVER-SEEZ or equivalent to all pins and bores.
Note 2: Check to make sure that sheave assemblies (items 1, 205) are packed with grease.
If not, pack with MOBILUX E.P. #2 grease (MCC 471197) or equivalet.
Note 3: BOLT TORQUE (WITH LOCTITE #271)
Apply to treads, LOCTITE #271 (MCC 622292).
Torque bolts on item 7 to 180 ft.lbs (243 Nm).
Note 4: Alternative sheave assembly 81005422 can be used in place of sheave 171250. Alternative
sheave assembly contains NTN beaing 81005423. NTN sheaves will be identigied by a white
strip in 3 to 4 places on the erope groove.
Note 5: Alternative sheave assembly 81006222 can be used in place of sheave 81009219.
Alternative sheave assembly contains hearing 81005423. Sheaves will be indentified by a
white strip in 3 or 4 places on the rope groove.
Note 6: Luffing jib preperation (options 2 or 4) CANNOT be used wtih #58WA Boom.
Note 7: a) Without Luffing Jib Preparation
b) With Luffing Jib Preparation.
Note 8: Continuous Reeving Sheeve Location
0-1660, 0-1665
ASSEMBLY REVISION
01−26−2011
O−NUMBER CODE INDEX
Serial Number 16007018
This section contains all of the available O−Numbers for 16007018.
01−26−2011
MANITOWOC CRANES, INC.
MODEL
ALL
6310660 1 SHEAVE ASSEMBLY (20" O.D. x 2" I.D. for 3/4" dia. rope)
1 224579 1 BEARING
2 622898 2 SEAL, Oil
ASSEMBLY REVISION
O-486 P
1 of 3
MODEL
ALL
6310920 1 SHEAVE ASSEMBLY (42" O.D. x 8" I.D. for 1-1/8" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
6315240 1 SHEAVE ASSEMBLY (30" O.D. x 8" I.D. for 1-1/4" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
6315250 1 SHEAVE ASSEMBLY (27" O.D. x 5" I.D. for 1" dia. rope)
1 9086220013 1 CONE, Bearing
9086220014 1 CUP, Bearing
2 9086220012 2 SEAL, Oil
A004920 1 SHEAVE ASSEMBLY (36" O.D. x 8" I.D. for 1-1/2" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A004930 1 SHEAVE ASSEMBLY (36" O.D. x 8" I.D. for 1-1/4" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A060830 1 SHEAVE ASSEMBLY (24" O.D. x 8" I.D. for 1-1/4" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A103500 1 SHEAVE ASSEMBLY (36" O.D. x 8" I.D. for 36mm dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A103510 1 SHEAVE ASSEMBLY (36" O.D. x 8" I.D. for 34mm dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A105690 1 SHEAVE ASSEMBLY (36" O.D. x 8" I.D. for 1-1/4" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A105700 1 SHEAVE ASSEMBLY (30" O.D. x 8" I.D. for 1-1/4" dia. rope)
9970220002 1 KIT, Bearing
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
A114400 1 SHEAVE ASSEMBLY (24" O.D. x 127cm I.D. for 1-1/8" dia. rope)
1 2250190 BEARING
2 6227720 2 SEAL, Oil
A153030 1 SHEAVE ASSEMBLY (48" O.D. x 8" I.D. for 1-1/2" dia. rope)
9970220002 1 KIT, Bearing
ASSEMBLY REVISION
2 of 3
MODEL
ALL
1 9069220018 1 BEARING
2 9794220046 2 SEAL, Oil
ASSEMBLY REVISION
WEDGE / SOCKET
ASSEMBLY REVISION
O-890 F
1 of 2
MODEL
All
SOCKET/WEDGE
Terminator
646242, 646245, 646246, 646247, 713266, A15281
ASSEMBLY REVISION
2 of 2
Manitowoc
ASSEMBLY REVISION
O-1230 D
1 of 2
MODEL
555, 777, 888, 999, 15000, 16000
HOOK BLOCK
45 US Ton (41 Metric Ton)
236503
ASSEMBLY REVISION
2 of 2
Manitowoc
16
15
1 5 8 7
2 3 11 4 9
12 13
Idendtification Plate
ASSEMBLY
O-1323
B
REVISION
1 of 2
HYDRAULIC CYLINDER (COUNTERWEIGHT PIN PULLER)
MODEL
16000
HYDRAULIC CYLINDER
Counterweight Pin Puller
A12175
1 9372220568 1 ROD
2 9372220086 1 WIPER, Rod
3 9372220247 1 HEAD
4 9372220123 1 O-RING
5 9372220569 1 TUBE ASSEMBLY
7 9372220126 2 SEAL, Piston
8 9372220127 1 GUIDE, Piston
9 9372220129 1 NUT, Hex
11 9372220249 1 SEAL, Head
12 9372220128 1 O-RING
13 9372220125 1 PISTON
15 9372220124 1 RING, Back-up
16 9372220163 2 PLUG (SAE-6)
ASSEMBLY REVISION
2 of 2
Manitowoc
ASSEMBLY REVISION
O-1358 C
1 of 2
MODEL
16000
HOOK BLOCK
250 Ton, 28mm Rope
A13155
2 of 2
Manitowoc
ASSEMBLY REVISION
O-1363 B
1 of 2
MODEL
16000
WEIGHT BALL
20 Ton 1-1/8" Rope
A13737
ASSEMBLY REVISION
2 of 2
Manitowoc
ASSEMBLY REVISION
O-1377 C
1 of 2
MODEL
16000
HOOK BLOCK
200 US Ton - 1-1/8" Rope
A14824
ASSEMBLY REVISION
2 of 2
Manitowoc
ASSEMBLY REVISION
O-1390 B
1 of 2
MODEL
16000
HOOK BLOCK
100 Metric Ton, 28mm Rope
A13154
ASSEMBLY REVISION
2 of 2
MANITOWOC CRANES, INC.
ASSEMBLY REVISION
O-1408 A
1 of 3
MANITOWOC CRANES, INC.
ASSEMBLY REVISION
O-1408 A
2 of 3
MODEL
16000
HOOK BLOCK
100 Metric Tons
A159270
ASSEMBLY REVISION
ASSEMBLY REVISION
O-1454 A
1 of 2
MODEL
16000
HOOK BLOCK
100M Ton - 28/32mm Rope 3 Sheave
A177400
ASSEMBLY REVISION
2 of 2
Manitowoc
MODEL
16000, 18000
SOCKET BUTTON
(for 28 mm or 32 mm rope with pin)
A06278
ASSEMBLY REVISION
MODEL
16000, 18000
SHEAVE ASSEMBLY
24" O.D. x 5" I.D. Dia. (1" Wire Rope)
1 225019 1 BEARING
2 429000 1 FITTING, Grease
3 429658 1 FITTING, Adapter Straight
4 622772 2 SEAL, Oil
5 696005 1 TUBING
6 81000951 1 FITTING, Relief Grease
7 81007873 1 SHEAVE, Wire Rope
8 81007935 1 FITTING, Adapter (90 Degree)
ASSEMBLY REVISION
O-1660 A
1 of 1
Manitowoc
ASSEMBLY REVISION
O-1665 B
1 of 2
MODEL
555, 777, 888, 999, 1015, M-250, M-250T, 2250, M-1200 RINGER, 15000, 16000, 18000, 4100
SHEAVE
30" Diameter
171250
Note: Pack with N.G.L.I. EP #2 grease at sheave assembly. Do not neglect to pack area
around seal (item 2).
ASSEMBLY REVISION
2 of 2
Manitowoc
MODEL
M-250, 2250, 14000, 16000, 18000
SHEAVE ASSEMBLY
24” Diameter (1" or 7/8" Wire Rope)
171964
1 171963 1 SHEAVE
2 225019 1 BEARING, Spherical Roller
3 622772 2 SEAL, Oil
Note: Pack with N.G.L.I. EP #2 grease at sheave assembly. Do not neglect to pack area SHEAVE (24" DIAMETER)
around seal (item 3).
ASSEMBLY REVISION
ASSEMBLY REVISION
O-1670 C
1 of 2
MODEL
16000, 18000
Note 1: Pack with NGLI EP#2 grease at sheave assembly. Do not neglect to pack area around
seal.
Note 2: Stamp part number on web near PIC.
Note 3: All exposed surfaces except bearing bore are to be coated with standard enamel paint
per indicated code.
ASSEMBLY REVISION
2 of 2
Manitowoc
ASSEMBLY
O-1673
B
REVISION
1 of 2
HOOK BLOCK, 5 SHEAVE (200 TON / 28MM ROPE)
MODEL
16000
HOOK BLOCK
200 Ton - 32 mm Rope
81007437
ASSEMBLY REVISION
2 of 2
Manitowoc
SHEAVE ASSEMBLY
1-1/8", 1-1/4", 1" or 7/8" Wire Rope
81005422
ASSEMBLY REVISION
SHEAVE ASSEMBLY
1-1/8" Wire Rope
81006222
ASSEMBLY REVISION
O-1807 B
1 of 2
MODEL
16000
SHEAVE
30" O.D. x 8" I.D. Dia. (1-1/8" Wire Rope)
81010374
Note: Pack with N.G.L.I. EP #2 grease at sheave assembly. Do not neglect to pack area
around seal (item 2).
ASSEMBLY REVISION
2 of 2
Manitowoc Cranes, Inc.
Specialty Bill By Alpha Description
For Serial #: 16007018
DESCRIPTION DRAWING NO. GROUP DRAWING REV.
Boom Point, Extended Upper 81009978 F B
Boom Rigging, #58WA 81009833 F 07−27−2010
Bracket, Transceiver 81011005 F B
Cap, Boom 81009868 F C
Counterweight, Upperworks 81010340 A A
Electrical Wiring, Boom Limits And Load Indicator A10868 F E
w/#81013558 Harness In Place Of #81000199
Insert, 12M (#58 Boom w/Straps) 81011915 F A
Insert, 3M Heavy (#58 Boom w/Straps) 81009839 F B
Insert, 6M Heavy (#58 Boom w/Straps) 81009834 F B
Intermediate Suspension, #58 Boom 81009986 F E
Nameplates & Decals (English) A12868 A 12−20−2010
Wire Rope Guide, Upper A12785 F F