Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. Manufactured and certified by MMLJ, lnc. 5711 Schurmier Ad. Houston, TX 77048
(Name and address of Manufacturar)
2. Manufactured for Stock
(Name and address of Purchaser)
3. Location of installation U_n_kn_o_w_n _
(Name and address)
4. Type v_e_rt_ic_a_l _ Tank 4.3 Cubic Feet 35H15-46H15
(Horizontal, vertical, or sphere) (Tank, separator, jkt. vessel, heat exch., etc.) (Manufacturer's serial number)
133786/003 6419~1f4~'ó 2015
(CRN) (Drawing numberl (National Board number) (Year built)
5. ASME Code, Section VIII, Div. 1 2013
(Edition and Addenda, if applicable (date)) (Code Case number)
ltems 6-11 incl. to be completed far single wa/1 vessels, jackets of jacketed vessels, she/1of heat exchangers, or chamber of multichamber vessels.
6. Shell: (a) Number of course(s) 1 (b) Overall length O'· 151/2"
Course(s) Material Thickness Long. Joint (Cat. A) Circum. Joint (Cat. A, B & C) Heat Treatment
No. Diameter Length Spec./Grade or Type Nom. Corr. Type Full, Spot, None Eff. Type Full, Spot, None Eff. Temp. Time
24"0D 7" SA-538-ERW 1/4" None E Non e 70% 2 None 70% n/a n/a
n/a
8. Type of jacket Jacketclosure -----------º-'-ª-----------
(Describe as ogee and weld, bar, etc.)
n/a
lf bar, give dimensions lf bolted, describe or sketch.
9. MAWP 150 n/a 300 nla Min. design metal temp. ·_2_oº_F at __ 1_5_0'-p
__ 51_·
at max. temp.
(Internan (Externa!) (Internan (Externan
10. lmpact test ---------...,.,......,.,..._N_o_._1m~p-a_ct_s_N_ot,..R,..eq~u-i_red_P_er_u...,G..,-20-,-(~f)--....,,.---------
at test temperature of ---------
llndicate yes orno and the component(s) impact tested)
11. Hydro., pneu., or comb. test pressure Hydrostatic 225 psi Proof test 1_n_a_cc_o_rd_a_n_ce_1o_P_E_D_M_od_u_l_e_a_-1_o_f_A_nn_e_x_ll_l
S_o_u_n_d_E_n~g_.
P_r_a_ct_ic_e_s
__
(Floating (material spec. no.JI (Diameter) (Nominal thickness) (Corr. allow.J (Attachment)
13. Tubes _
(Material spec. no., grade or type) (O.O.) (Nominal thickness) (Number) (Type (straight or U))
(07/13)
FORM U-3 (Back)
ltems 14-18 incl. to be completed far inner chambers of jacketed vesse/s or channels of heat exchangers.
14. Shell: (a) No. of course(s) (b) Overall length ----------------
Course(s) Material Thickness Long. Joint (Cat. A) Circum. Joint (Cat. A, B & C) Heat Treatment
No. Di a meter Length Spec./Grade or Type Nom. Corr. Type Full, Spot, None Eff. Type Full, Spot, None Eff. Temp. Time
n/a
Location (Top, Thickness Radius Elliptical Conical Hemispherical Flat Side to Pressure Category A
Bottom, Ends) Min. Corr. Crown Knuckle Ratio ApexAngle Radius Di a meter Convex Concave Type Full, Spot, None Eff.
(a) n/a
(b)
20. Supports: Skirt -..,,.,--N_o---,- Lu gs --,,.,..-0-,---.,..-- Legs ___,,.,---3,........,_ Others ---~n_iª~~-- Attached B=.H~e_a_d_W_e~ld~e_d.,..-_
(Yes orno) (N umberl (Number) (Describel (Where and how)
21. Manufacturer's Partial Data Reports properly identified and signed by Commissioned lnspectors have been furnished for the following items of
the report (list the name of part, item number, Manufacturer's name, and identifying number):
12.) UG-125 Safety Devices Are Not Provided By Tlle Marmfacturer But Overpressure Protectior1
Shall Be Prov1ded Pnor 1 o Placmg I he Vessel In Serv1ce. For Non-Corros1ve Serv1ce.
Signed -"~"'-'-"'-~"'"'-'-""4-C""·,..__~..,.//0'-c-'~~--~·-=---,~~-------
(Certified individual)
(07/13)