Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Catalog HY13-1560-002/US
1560-002.P65, pm
X System Type
HGF
0 Open Center Nonreversing
Displacement
1* Open Center Nonreversing
XX in3/rev cm3/rev
(low noise)
08 3.30 54.1
2 Open Center Reversing
10 4.13 67.7
6 Power Beyond Nonreversing
12 4.95 81.1
3 Power Beyond Reversing
16 6.60 108.2
4 Closed Center Nonreversing
20 8.25 135.2
7 Closed Center Reversing
24 9.90 162.3
* Only available with port option 2
X Porting
2 Female #6
X Relief Option
SAE O-Ring
2 No Relief
4 Female #6 SAE O-Ring
4 921 psi (64 Bar)
Side Port
7 1200 psi (83 Bar)
6 1560 psi (108 Bar)
8 1740 psi (120 Bar)
P R
Example:
HGF08220 signifies HGF Hydraguide
series unit with 3.30 in3/rev
displacement, open center,
nonreversing with female
#6 SAE O-Ring ports.
1560-002.P65, pm
HGF
Hydraguide™ Series 08 10 12 16 20 24
Displacement English 3.30 4.13 4.95 6.60 8.25 9.9
(in3/rev) (cm3/rev) Metric 54.1 67.7 81.1 108.2 135.2 162.3
Operating Pressure Maximum 1800 1800 1800 1800 1800 1800
(psi) (Bar) 125 125 125 125 125 125
Operating Temperature Maximum 200 200 200 200 200 200
(°F) (°C) 93.3 93.3 93.3 93.3 93.3 93.3
Continuous 8 8 8 8 8 8
Flow Rated 30.3 30.3 30.3 30.3 30.3 30.3
(gpm) (liters/min)
Recommended2 1.71 2.15 2.57 3.43 4.29 5.14
(120 rpm) 6.47 8.14 9.73 12.98 16.24 19.45
Weight 8.8 9.04 9.28 9.77 10.25 10.75
(lbs) (kg) 3.99 4.10 4.21 4.43 4.65 4.88
“A” Dimensions3 4.37 4.50 4.62 4.87 5.12 5.42
(in) (mm) 111.0 114.2 117.3 123.6 130.0 137.5
“B” Dimensions 5.3 5.4 5.6 5.8 6.1 6.4
(in) (mm) 134.6 137.1 142.2 147.3 154.9 162.6
1
English dimensions are control values; metric values are conversions.
2
For two handwheel turns per second.
3
Length from mounting face to end of Hydraguide end.
100 6.9
80 5.5
(BAR)
(PSI)
60 4.1
40 2.8
20 1.4
1 2 3 4 5 6 7 8 9 10
Inlet Flow (GPM)
1560-002.P65, pm
45˚
AUX TYP
LT OUT LT
3.05
RT RT
IN IN
72˚
TYP
(4) 5/16-24 UNF-2A Thread Studs
3.05 (77.3)
9/16-18 Straight Thread Equally Spaced & Located On A
MAX TYP
SAE #6 Female O-Ring Ports Ø3.250 (82.55) Circle
on a Ø1.66 (42.16) Circle
“A” Dimensions
Series 08 10 12 16 20 24
(in) 4.16 4.28 4.41 4.66 4.91 5.16
(mm) 105.7 108.7 112.0 118.4 124.7 131.1
45˚
TYP
3.17 (80.5)
OUT
LT
Max
.62 (15.7)
AUX
IN
RT
.56 (14.2)
Note:
9/16-18 Straight Thread O-Ring Ports 1. All dimensions are for reference only.
2. Add .50 in (12.7 mm) for integral relief.
“B” Dimensions (Porting option 2 only)
Series 08 10 12 16 20 24 3. Reversing units shall be used with
(in) 5.38 5.50 5.63 5.88 6.13 6.38 balanced area cylinders.
(mm) 136.6 139.7 143.0 149.3 155.7 162.1
Adapter Fittings
411085A1 411090A1
Straight Thread SAE #6 O-Ring Straight Thread SAE #6 O-Ring
Male JIC 37o Flare Parker Seal-Lok 9/16 x 18
1560-002.P65, pm
3.17 (80.5)
Max
OUT
LT
.62 (15.7) AUX
IN
RT
.56 (14.2)
Note:
1. All dimensions are for reference only.
2. Add .50 in (12.7 mm) for integral relief.
9/16-18 Straight Thread (Porting option 2 only)
SAE #6 O-Ring Ports (5) 3. Reversing units shall be used with
on a Ø1.66 (42.16) Circle balanced area cylinders.
“B” Dimensions
Series 08 10 12 16 20 24
(in) 5.38 5.50 5.63 5.88 6.13 6.38
(mm) 136.6 139.7 143.0 149.3 155.7 162.1
1560-002.P65, pm
Standard Column
“B” Length
.89 1.38 .50
REF
.858 Dia.
Ø1.60
Gage
.623 Taper
Per Foot
.156
.875 x 36 13/16-20
Straight Serrations UNF-2A Thd.
Hornwire Column
(Single or Dual Contact) “B” Length 4.00
.858 Dia.
Ø1.60
Gage
.623 Taper
Per Foot
.156 2.13
.875 x 36 13/16-20
Straight Serrations UNF-2A Thd.
Notes:
1. All dimensions are for reference only.
2. Jacket tube diameter of all columns is 1.50 inches.
3. Column support is required for columns longer than 10 inches.
4. For “B” length see HGF Steering Column Selection Chart, page C16.
1560-002.P65, pm
HGF
HGF
Notes:
1. Steering wheel horn button not included in
column kits. Order part number 465611
separately.
2. Steering wheel nut included with column.
3. For column lengths or horn wires not
shown above, contact your Parker Sales
Engineer.
1560-002.P65, pm
Hydraguide™
RELIEF
VALVE
RESERVOIR
FILTER
1560-002.P65,pm
The nonreversing unit keeps the steered wheels in the The reversing unit allows the steered wheels to return to
steered position when the operator releases the steering the straight ahead position after the operator releases
wheel. The cylinder ports are blocked in the neutral the steering wheel. This happens only if the steering
valve position. The operator must steer the wheels geometry exerts a centering force on the steering
back to the straight ahead position. cylinder. The cylinder ports are interconnected with the
metering section so that the steering wheel follows the
wheels back to center position. Reversing steering units
should only be used in systems where the opposing
cylinder chambers are of equal volume. DO NOT USE
with a single unequal area/volume cylinder.
STRG.
WHL.
STRG.
WHL.
STRG.
WHL.
1560-002.P65, pm
TO OTHER
CIRCUITS
1560-002.P65,pm
Flow Chart
Use the following chart as a guide to design hydrostatic
steering systems.
1 2 3
Existing System New system where steering New system where steering
forces and cylinder stroke(s) are forces and cylinder stroke(s) are
known. unknown.
1560-002.P65, pm
.4 Where:
.3 KT = Kingpin torque available. If one cylinder is SV = (Bore area - rod
.2
(inch-pounds) used, use the rod end area area) x cylinder
.1 only and, if two are used,
R = Minimum radius stroke
.2 .4 .6 .8 1.0 1.2 arm (inches) use the rod end area plus
E
B (see Diagram 2) the head end area to select π
Diagram 1 the cylinder (Step VI). SV = — [B2 - R2] x S
Diagram 2 4
B
E
Stroke
1.2 Calculate Kingpin
_______
torque: a. Head side
Where:
KT = Kingpin torque
in inch-pounds
W = Weight on steered
axle in pounds
(Use maximum
overloaded weight
anticipated.)
mu = Coefficient of
friction
B = Nominal Tire width
(inches)
E = Kingpin offset
(inches) at the
intersection with
the ground
1560-002.P65,pm
NOTE:
Reversing units used with
balanced area cylinders.
HGF Series
Open Center
Closed Center
Power Beyond
Operating Parameters:
1800 PSI
8 GPM
3.3 to 9.9 cu. in.
Typical Systems:
Turf, Material Handling, General Purpose,
and Light Agricultural Vehicles.
1560-002.P65, pm
Date _______________
Salesperson ______________________
2. Vehicle
Truck Tractor Lift Truck Earth Mover Other _______________
3. Vehicle Specifications
3.1 Number of Steered Wheels ___________ Front Wheel Steer Rear Wheel Steer Articulated
3.2 Gross Vehicle Weight and Maximum Weight on Steered Axle:
4. Steering Unit
Operating Parameters
4.1 Number of Hand Wheel Turns Requested: _____ 4.1.1 Steering Effort @ Expectations ____ In Lb (Kg. cm.)
4.2 Speed of Steer (Seconds - Lock to Lock): Low Idle ____________ Sec. High Idle ____________ Sec.
5. Steering Cylinder
5.1 Number Used ____________ Balanced Yes No
5.2 Bore ___________ In. (cm) 5.2.1 Stroke ____________ In. (cm) 5.2.2 Rod Dia. _____ In (cm)
6. Pump
Model Number _______________________ Displacement: Fixed Variable
6.2 Pressure Relief Integral External Maximum Relief Setting _______________ PSI (Kg/cm²)
6.3 Flow Divider Yes No
6.4 Pump Flow High Idle ___________ GPM (L/min.) Low Idle _____________ GPM (L/min)
6.5 Flow Available Maximum Steering Flow _____ GPM (L/min.) Minimum Steering Flow ____ GPM (L/min)
6.6 Full Engine Speed _________ RPM Idle Engine Speed _________ RPM
7. Reservoir
7.1 Capacity _________ Gal.
Additional Information:
1560-002.P65, pm
1560-002.P65,pm
Catalog HY13-1560-002/US