Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
810-2009108
The above models are classified as green products (*1), as indicated by the underlined serial numbers.
This Service Manual describes replacement parts for the green products. When repairing these green
product(s), use the part(s) described in this manual and lead-free solder (*2).
LEAD-FREE SOLDER
(*2)
This product is manufactured using lead-free solder as a part of a movement within the
consumer products industry at large to be environmentally responsible. Lead-free solder must
be used in the servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
2. General Specifications................................................................................................................... 6
Disassembly Tools......................................................................................................................................10
6. Packing diagram.......................................................................................................................... 68
10. Troubleshooting......................................................................................................................... 80
11. Firmware.................................................................................................................................... 84
3
1. Safety Notices and Precautions
Prior to using this service guide, ensure that you have carefully followed all the procedures outlined in the
15SLDT3R/19SLDT3R/22SLDT3R/26SLDT3R LCD TV user manual. Make sure to note and follow all
warnings and instructions marked on the product. Save these instructions for future reference.
CAUTION
THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL
CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE
MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE
PROCEDURE.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE
ENCLOSURE.
VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT
STARE INTO BEAM.
4
Preparation of Servicing
The laser diode used for a pickup head may be destroyed with external static electricity.
Moreover, even if it is operating normally after repair, when static electricity discharge is received at
the time of repair, the life of the product may be shortened.
Please perform the following measure against static electricity, be careful of destruction of a laser
diode at the time of repair.
Place the unit on a workstation equipped to protect against static electricity, such as
conductive mat.
Soldering iron with ground wire or ceramic type is used.
A worker needs to use a ground conductive wrist strap for body.
Servicing Environment
1. This LCD TV should be used only with the power source type identified on the package and on
the user’s guide.
2. Service the LCD TV in a room with low humidity and free of dust.
3. Place the LCD TV on a stable, level surface. Subjecting the LCD TV to a drop or sharp impact
may cause severe damage to thin glass, plastic surface materials, and internal components.
4. If necessary, clean the LCD TV with a slightly damp cloth using clean water. Disconnect the LCD
TV from the power source before cleaning. Do not use ammonia-based cleaning products.
5. In the event that the powered LCD TV rapidly heats, or emits unusual smells or noises,
immediately disconnect the unit from the power source.
6. To avoid electrical hazard, make sure that the LCD TV is fully assembled—the casing closed and
all the screws tightened completely—before plugging it in for testing.
7. The LCD TV’s internal components may be damaged by electrostatic discharge (ESD). Carry out
repairs in an ESD-protected workshop. If no such workshop is available, wear an antistatic wrist
strap or touch a highly conductive metal object.
8. Before opening the housing, disconnect the LCD TV from all power sources and remove all
peripheral cables. If the LCD TV has not been disconnected from the power outlet before being
opened, there is a danger to life through electric shock. There is also a risk of damage to the
components.
5
2. General Specifications
The product specifications listed in this section are subject to change without notice.
Item Description
Panel
Size (approximate screen 15.6 in (396.24 mm) 18.5 in (469.9 mm) 21.6 in (548.64 mm) 26.0 in
size, diagonal)
DVD/CD Player
S-Video input (Y) 1.0 V (p-p), 75 ohm, negative sync, 4-pin mini-DIN x 1
(C) 1.0 V (p-p), 75 ohm
ColorStream video input (Y) 1.0 V (p-p), 75 ohm, negative sync, RCA jack x 1
(component) (Pb, Pr) 0.7 V (p-p), 75 ohm, RCA jack x 2
Video input (composite) 1.0 V (p-p), 75 ohm, negative sync, RCA jack x 1
PC input Monitor: 15-pin mini-D sub x 1; audio: 3.5-mm stereo mini jack x 1
Operation 33 W 35 W 55 W 100 W
Standby 0.8 W
Operating Conditions
Dimensions (W x D x H) 15.84 x 12.59 x 5.55 in 18.58 x 15.79 x 8.15 in 21.12 x 17.3 x 8.15 in 26.83 x 20.16 x 8.99 in
(402.4 x 319.7 x 141 mm) (472 x 401 x 207 mm) (536.5 x 439.5 x 207 mm) (681.4 x 512.1 x 228.3 mm)
Weight 2.99 kg (6.59 lb) 4.63 kg (10.21 lb) 5.3 kg (11.68 lb) 8.57 kg (18.89 lb)
Warning! Do not set your computer graphics card to exceed the unit’s refresh rates; doing so may cause damage to the LCD TV.
6
3. Function Testing
7
Hotel Mode Function
Input mode start 1-99ch/DTV/AV1/AV2/ OFF Setting of input source at power supply On. (Note
COMPONENT/HDMI/ 3)
PC/DVD/OFF
Notes:
1. Even if set to “No Respond”, the remote control key operation in Hotel mode and service mode function
are effective.
2. Even if set to “No Respond”, the service mode function is effective.
3. If set to “Off”, it starts up in the same input source before you turn off the power.
9
4. System Disassembly
Disassembly Tools
The following tools are required for disassembling the system.
Wrist-grounding strap and conductive mat for preventing electrostatic discharge
Philips screwdriver
Hex screwdriver
Disassembly Reminders
Electrostatic Discharge (ESD) precautions should be observed to prevent damaging the
internal components.
Follow the sequence indicated in the illustrative figures when removing the screws
securing the components.
The screws for the different components vary in size. During the disassembly process,
group the screws with their corresponding components to avoid mismatches when putting
back the components.
After removing the adhesive tapes, paste them back near their original location for use
during system reassembly.
Prior to disassembly, place the LCD TV on a stable, level surface protected by a cushion.
10
15SLDT3R
1. Lay down the LCD TV on a flat, stable surface with the rear cover facing up. Make sure
the lip edge of the front bezel is hanging over the edge of the surface.
2. Remove the screws securing the LCD TV base
11
4. Remove the screws securing the rear panel cover.
12
6. Open and remove the left rear panel door.
8. Detach the top part of the rear panel cover from the housing and tilt it back to expose the
LCD cable on the LCD panel; then disconnect the LCD cable, and remove the rear panel.
Caution: As FFC connector for LCD panel can easily be damaged during disassembly or reassembly, handle
it with care.
13
Note: Take note of the spring orientation when reassembling the TV.
14
10. Disconnect the cable from the LED board; then pull up to remove the IR board.
15
12. Disconnect the cable from the control board; then remove the control board.
13. Unlatch the control board from its plastic bracket to separate it from its case.
16
14. Remove the screws securing the power board.
15. Lift up the power board at an angle; then disconnect the two cables, and remove the
power board.
17
16. Remove the screws securing the mainboard.
18
18. Lift up the mainboard; then disconnect the two cables.
19
20. Lift up and remove the optical drive.
21. Pull up to release the left and right speakers. Take note to release the speaker cables
from their latch.
20
22. Release the LCD panel from its latches.
21
19SLDT3R
1. Lay down the LCD TV on a flat, stable surface with the rear cover facing up. Make sure
the lip edge of the front bezel is hanging over the edge of the surface.
2. Remove the screws securing the LCD TV base
22
4. Remove the screws securing the rear panel cover.
23
6. Open and remove the center rear panel door.
Caution: As FFC connector for LCD panel can easily be damaged during disassembly or reassembly, handle
it with care.
24
8. Remove the screw securing the left rear panel door.
25
10. Disconnect the power cables.
11. Detach the top part of the rear panel cover from the housing, and remove the rear panel.
26
Note: Take note of the spring orientation when reassembling the TV.
27
13. Pull up to remove the IR board; then disconnect the cable from the IR board.
28
15. Disconnect the cable from the control board; then remove the control board.
16. Unlatch the control board from its plastic bracket to separate it from its case.
29
17. Remove the screws securing the power board.
18. Turn the power board over; then disconnect the two cables, and remove the power board.
30
19. Remove the screws securing the mainboard.
20. Lift the mainboard at an angle; then disconnect the speaker cable.
31
21. Turn the mainboard over; then disconnect the two cables.
24. Pull up to release the left and right speakers. Take note to release the speaker cables
32
from their latches.
33
22SLDT3R
1. Lay down the LCD TV on a flat, stable surface with the rear cover facing up. Make sure
the lip edge of the front bezel is hanging over the edge of the surface.
2. Remove the screws securing the LCD TV base
34
4. Remove the screws securing the rear panel cover.
35
6. Open and remove the center rear panel door.
Caution: As FFC connector for LCD panel can easily be damaged during disassembly or reassembly, handle
it with care.
36
8. Remove the screw securing the left rear panel door.
37
10. Disconnect the power cables.
11. Detach the top part of the rear panel cover from the housing, and remove the rear panel.
Note: Take note of the spring orientation when reassembling the TV.
38
12. Pull up to remove the IR board; then disconnect the cable from the IR board.
39
14. Disconnect the cable from the control board; then remove the control board.
15. Unlatch the control board from its plastic bracket to separate it from its case.
16.
40
17. Remove the screws securing the power board.
18. Turn the power board over; then disconnect the two cables, and remove the power board.
41
19. Remove the screws securing the mainboard.
20. Lift the mainboard at an angle; then disconnect the speaker cable.
42
21. Turn the mainboard over; then disconnect the two cables.
43
23. Lift up and remove the optical drive.
24. Pull up to release the left and right speakers. Take note to release the speaker cables
from their latches.
44
45
26SLDT3R
1. Lay down the LCD TV on a flat, stable surface with the rear cover facing up. Make sure
the lip edge of the front bezel is hanging over the edge of the surface.
2. Remove the screws securing the LCD TV base
46
4. Remove the screws securing the rear panel cover.
47
6. Open and remove the left rear panel door.
48
8. Remove the screw securing the center rear panel door.
49
10. Disconnect the LCD cable.
Caution: As FFC connector for LCD panel can easily be damaged during disassembly or reassembly, handle
it with care.
11. Detach the top part of the rear panel cover from the housing, and remove the rear panel.
50
Note: Take note of the spring orientation when reassembling the TV.
51
14. Remove the screws securing the control board.
15. Disconnect the cable from the control board; then remove the control board.
52
16. Unlatch the control board from its plastic bracket to separate it from its case.
53
18. Turn the power board over; then disconnect the two cables, and remove the power board.
54
20. Release the cables from their latches.
21. Lift up the mainboard at an angle and disconnect the speaker cable.
55
22. Turn the mainboard over; then disconnect the two cables.
56
24. Lift up and remove the optical drive.
25. Pull up to release the left and right speakers. Take note to release the speaker cables
from their latches.
57
26. Remove the screws securing the LCD bracket to the LCD panel.
58
28. Remove the LCD panel from the front bezel.
59
5. Exploded Diagram
15SLDT3R
<to be provided>
60
Parts List: 15SLDT3R
SAFETY PRECAUTION
The parts identified by mark are critical for safety. Replace only with part number specified. The
mounting position of replacement is to be identical with originals.
The substitute replacement parts which do not have the same safety characteristics as specified in the
parts list may create shock, fire or other hazards.
61
19SLDT3R
<to be provided>
62
Parts List: 19SLDT3R
SAFETY PRECAUTION
The parts identified by mark are critical for safety. Replace only with part number specified. The
mounting position of replacement is to be identical with originals.
The substitute replacement parts which do not have the same safety characteristics as specified in the
parts list may create shock, fire or other hazards.
63
22SLDT3R
<to be provided>
64
Parts List: 22SLDT3R
SAFETY PRECAUTION
The parts identified by mark are critical for safety. Replace only with part number specified. The
mounting position of replacement is to be identical with originals.
The substitute replacement parts which do not have the same safety characteristics as specified in the
parts list may create shock, fire or other hazards.
65
26SLDT3R
<to be provided>
66
Parts List: 26SLDT3R
SAFETY PRECAUTION
The parts identified by mark are critical for safety. Replace only with part number specified. The
mounting position of replacement is to be identical with originals.
The substitute replacement parts which do not have the same safety characteristics as specified in the
parts list may create shock, fire or other hazards.
67
6. Packing diagram
15SLDT3R
68
19SLDT3R
69
22SLDT3R
70
26SLDT3R
71
7. Block Diagrams
Sound amp unit
72
DVD module
73
Power supply unit
74
8. Printed Circuit Board
Top
75
Bottom
76
9. Interconnection diagram
77
78
79
10. Troubleshooting
No Display on Screen (Screen is black, no power)
No Power/No Video
Yes
No
Video Audio
(5Vsb,12V)
Check power on Main board
No
80
Power Check step
NO
Does power have Check power BD
5Vsb?
NO
Have 3.3Vsb? Check U208 pin2
Yes
NO
Does power
have 12V?
NO
NO
Have 6V? Check L242 pin2
Yes
Yes
NO
Have 5V? Check L212
Yes
Yes
NO
81
Video problem
Video problem
No
Is OSD on the Check panel power on LVDS
screen cable:
picture?
Check tuner CVBS Check signal Check signal path Check signal path
signal to scaler, I2C, path from from connector to the from connector to the
82
Speaker No Sound (Test signal: ≦0.5Vrms @1kHz sine waveform)
Audio Problem
No Audio issue
No Audio
Please ensure the signal cable is connected Note: Speaker will be muted when
Yes
Yes
NO
Check U801, U802 U801, U802 fail
output signal
Yes
83
11. Firmware
Checking the LCD TV Firmware Version
Follow these steps:
1. Turn on the LCD TV.
2. Press and hold the Volume – button on the LCD TV, and, at the same time, press and hold
the 8 button on the remote control.
3. After at least 2 seconds, release the buttons to display the firmware information.
MCU
CHECK SUM : xxxxxxxxxx
VERSION : Vx.xx.xxx
System F/W
CHECK SUM : xxxxxxxxxx
VERSION : Vx.xx.xxx
4. Press the Exit button on the remote control to close the window.
TV FIRMWARE UPDATE...
84
9. After the firmware update successfully completes, the following message appears on the LCD
TV screen. A finish dialog box also appears on the computer screen.
PROGRAM FINISH
15. After the MCU firmware update successfully completes, the following box appears. A finish
dialog box also appears on the computer screen
Update Finish.
Please plug AC Off/On
16. Disconnect the cables from the service connectors and the VGA connector.
85
Checking the DVD Firmware Version
Follow these steps:
1. Turn on the LCD TV.
2. Press the TV/DVD button on the remote control to enter DVD mode.
3. Press and hold the STOP button on the LCD TV, and, at the same time, press and hold the 1
button on the remote control.
4. After at least 2 seconds, release the buttons to display the firmware information.
86