Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
P-1
l Reference:
l Chapter 1:
l The unique innovation of OSN 6800 system is the three-level traffic grooming
infrastructure integrating dynamic optical cross-connect (Multi-degree ROADM)
flexible electric grooming (Any ADM) embedded L2 switch processing capability.
l L0 (Optical layer).
p Agile photonic layer has multi-degree wavelength cross-connect capacity,
and therefore provides the ability to route wavelengths to speed up service
delivery and reduce the cost of O-E-O conversion.
l L1(High order electrical layer).
p Huawei GE ADM is the first commercialized integrated GE transport and
switching system in the industry designed with Huawei own patents. Today,
Huawei has extended ADM solution to any service, Any ADM/MADM
solution implements any data channel end to end automated creation,
performance monitoring, fault detection, protection and traffic grooming
between different wavelengths across complicated network topologies.
l L2(Low order electrical layer).
p Embedded LAN switching processor implements local Ethernet traffic
aggregation, including convergence of n*GE to m* GE (m<n) or N*GE to
10GE LAN interface. It increases wavelength bandwidth utilization.
l The NE loaded with GMPLS Control Plane becomes the intelligent NE, on which
the ASON function can be supported.
l With the XCS, the grooming function is available between every two common slots.
(Centralize Cross-connect)
l Without the XCS, the grooming function is available between the neighboring paired
slots. (Distributed Cross-connect)
p V1R1/V1R2 share the same backplane hardware, which has two slots (IU1,
IU4) with16*ODU1 bus, no ODU2 bus;
p V1R3/V1R4 share the same backplane hardware, which has four slots (IU1,
IU4, IU11, IU14) with16*ODU1;
l For the backplane and platform identification, please contact with the local support
office.
l Chapter 2:
p Most of the boards are identical in OSN 3800, OSN 6800 OSN 8800 use
identical.
´ Board Types:
p Optical wavelength conversion board has the client side and WDM side
module.
´ Notes:
l The functional versions of the LOG board are available, that is, TN11 and TN12. The
major difference between the two versions lies in the support for pluggable optical
modules on the WDM side.
l Basic function
l One-to-one port connections are between the VCTRUNK ports and the AP ports of
the cross-connect module. You are not required to set one-to-one port connections
on the U2000.
l Basic function
p Converts four channels of 10GE WAN or 10GE LAN services received directly
on the client side, or two channels of 10GE services cross-connected from
the backplane, into two channels of standard WDM wavelength OTU2
signals and performs the reverse process.
p Converges multiple flat-rate 10GE services into one channel of 10GE service.
l One-to-one port connections are between the VCTRUNK ports and the AP ports of
the cross-connect module. You are not required to set one-to-one port connections
on the U2000.
´ Board Types:
p Tributary board only has the client side module. Tributary board gets the
service from the client side and send them to the backplane.
l NOTE:
p For the client services at a rate of greater than 1.25 Gbit/s (OC-48, STM-16,
FC200, FICON Express, OTU1, HDTV), the client-side interfaces can access up
to only one channel.
p The client-side GE optical module can be replaced with the electrical module
to access the corresponding electrical signals.
l Two functional versions of the TQM board are available, that is, TN11 and TN12. The
main difference between the two versions lies in whether the board of different
versions supports the function of processing OTU1/HDTV/DVB-SDI/FDDI services.
l The cross-connections between TX/RX and LP as well as between LP and the OP port
on Line card need to be configured.
l Only one functional version of the TDG board is available, that is, TN11.
l TBE can
l TBE supports the L2 electrical layer cross-connect and then the EVPL service is
available in TBE.
l The relevant L2 functions, like Stack VLAN, CAR and Cos, are available in TBE.
l In the protection application, both the active and standby TBE are recommended to
be inserted in the slots with 40G cross-connect capacity. If there’s only one 40G slots
left, the active TBE can be inserted in the 20G slot while the standby TBE is inserted
in the 40G slot.
l The TQS realizes the conversion between four STM-16/OC-48/OTU1 optical signals
and four ODU1 electrical signals.
l The cross-connections between TX/RX and LP need to be configured.
l Only one functional version of the TQS board is available, that is, TN11.
l The TN12TDX board supports the conversion between two channels of 10GE LAN/10GE WAN/STM-
64/OC-192 optical signals and two channels of 10 Gbit/s ODU2 electrical signals.
l The TN52TDX board supports the conversion between two channels of 10GE LAN/10GE WAN/STM-
64/OC-192/OTU2 optical signals and two channels of 10 Gbit/s ODU2 electrical signals.
l The TN53TDX board supports conversion between two channels of 10GE LAN/10GE WAN/STM-64/OC-
192/OTU2/OTU2e/FC800/FC1200 optical signals and two channels of ODU2/ODU2e/ODUflex electrical
signals, and supports conversion between two channels of FC800 optical signals and two channels of
ODUflex electrical signals
l Difference:
p The TN11TDX board supports the conversion between the client-side signals and ODU1
electrical signals.
p The TN12TDX board supports the conversion between the client-side signals and ODU2
electrical signals.
p The TN52TDX board supports the conversion between the client-side signals and
ODU2/ODU2v electrical signals.The TN52TDX board supports OTU2 service on the client side,
whereas the TN11TDX/TN12TDX board does not.
p The TN53TDX/TN57TDX board supports the conversion between the client-side signals and
ODU2/ODU2e/ODUflex electrical signals. Only TN53TDX board supports two channels of IEEE
1588v2 function, two channels of the physical clock function.
l The available functional versions of the TQX board are TN11, TN52, TN53, TN55.
l The TN11TQX/TN52TQX/TN53TQX board supports the conversion between the client-side signals and
ODU2/ODU2e electrical signals. The TN55TQX board supports the conversion between the client-side
signals and ODU2/ODU2e/ODUflex electrical signals.
l Only the TN55TQX board supports four channels of IEEE 1588v2 function.
l Only the TN55TQX board supports four channels of physical clock function
l Performs conversion between 16 channels of optical signals at any rate in the range
of 125 Mbit/s to 2.67 Gbit/s and 16 channels of ODU0 electrical signals.
l The TOM board has two working modes, that is, Cascading mode and Non-
cascading mode. There are totally 12 scenarios of the TN52TOM.
l The scenarios of the TN52TOM:
l In Cascading mode, there are four scenarios.
p Scenario 1: ODU0 Tributary Mode (Any->ODU0->ODU1])
p Scenario 2: ODU0 Tributary-Line Mode(Any->ODU0->ODU1->OTU1)
p Scenario 3: ODU1 Tributary Mode(Any->ODU1)
p Scenario 4: ODU1 Tributary-Line Mode(Any->ODU1->OTU1)
l In Non-cascading mode, there are eight scenarios.
p Scenario 5: ODU0 Tributary Mode(Any->ODU0[->ODU1])
p Scenario 6: ODU0 Tributary-Line Mode(Any->ODU0->ODU1->OTU1)
p Scenario 7: ODU1 Tributary Mode(OTU1/Any->ODU1)
p Scenario 8: ODU1 Tributary Mode(OTU1->ODU1->ODU0)
p Scenario 9: ODU1 Tributary Mode(OTU1->ODU1->Any->ODU0)
p Scenario 10: ODU1 Tributary Mode(OTU1->ODU1->Any->ODU0->ODU1)
p Scenario 11: ODU1 Tributary-Line Mode(OTU1->ODU1->Any->ODU0-
>ODU1->OTU1)
p Scenario 12: ODU1 Tributary-Line Mode(OTU1->ODU1->OTU1)
l NOTE:
p A ClientLP port can access only one service that has a rate higher than 1.25
Gbit/s, and this service can be configured in only the first channel of the
ClientLP port.
l NOTE: The OptiX OSN 6800 and OptiX OSN 3800 do not support Application 2 of
ODU1 Tributary Mode(OTU1->ODU1->ODU0) in non-cascading mode.
´ Board Types:
p Line board only has the WDM side module. Line board gets the service from
the backplane.
l The TN11NS3/TN52NS3 supports AFEC, and the TN54NS3 supports AFEC-2, and the
TN55NS3 supports HFEC. Boards that use different FEC modes cannot interoperate
with each other.
l Only the TN52NS3/TN54NS3/TN55NS3 board support the cross-connections of
ODU0/ODU1 level, and only the TN54NS3/TN55NS3 board support the cross-
connections of ODU3 level.
l The TN55NS3 board uses coherent receive technology.
l Only the TN54NS3 board supports IEEE 1588v2 function.
l The TN54NS3/TN55NS3 board can implement the electrical regeneration of
OTU3/OTU3e signals, whereas the TN11NS3/TN52NS3 board does not.
l The TN11NS3/TN52NS3 supports AFEC, and the TN54NS3 supports AFEC-2, and the
TN55NS3 supports HFEC. Boards that use different FEC modes cannot interoperate
with each other.
l Only the TN52NS3/TN54NS3/TN55NS3 board support the cross-connections of
ODU0/ODU1 level, and only the TN54NS3/TN55NS3 board support the cross-
connections of ODU3 level.
l The TN55NS3 board uses coherent receive technology.
l Only the TN54NS3 board supports IEEE 1588v2 function.
l The TN54NS3/TN55NS3 board can implement the electrical regeneration of
OTU3/OTU3e signals, whereas the TN11NS3/TN52NS3 board does not.
l Function of NQ2:
l The TN51NQ2 board supports the cross-connections at the ODU1 and ODU2 levels.
The TN52NQ2/TN54NQ2 board supports the cross-connections of at the ODU0,
ODU1 and ODU2 levels.The TN53NQ2 board supports ODU0, ODU1, ODU2, and
ODUflex cross-connections.
l Only the TN54NQ2 /TN53NQ2 board supports the IEEE 1588v2 function.
l Only the TN54NQ2 /TN53NQ2 board can realize the regeneration of OTU2/OTU2e
signals.
l Chapter 3:
l ODU2 Grooming on OSN 6800 and OSN 8800 cannot be taken via paired-slots.
l TN12LQMS supports 1*ODU1 cross-connection under the “NS1” mode, here the its
origin client Tx/Rx cannot access any services.
l Blue lines in vertical stands for distributed cross-connection via paired-slots in OSN
3800/6800 system, not for OSN 8800.
l GE level service granule takes the same data bus with ODU1 in OSN 3800/6800
system.
l Any service could be cross-connected via paired-slots only, not for centralized cross-
connection via XCS card.
l This combination is widely used in the network. Compared with the solution of OTU,
the combination of tributary unit and line unit can make the network more flexible.
l If we have one TQS and two NS2, the ODUk SNCP can be available.
l The NS2 in the slide refers to the TN12NS2. The TDX in the slide refers to the
TN12TDX.
l OptiX OSN 6800 supports two kinds of service grooming: distributed cross-connect
and centralized cross-connect.
l Distributed cross-connect supports three types of services. They are ODU1, GE, and
Any services.
l Centralized cross-connect supports three types of services. They are ODU2, ODU1
and GE services.