Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
htm) > Instructions for use
Instructions for using Fixed Beam Calculator
(i). Sign convention
(a) The loads acting upward are considered as positive while the downward loads are taken as negative. Sagging bending moment is taken as positive and hogging
as negative. The clockwise rotation and moments are negative and anticlockwise as positive.
(b) In case of Fixedend moments, the anticlockwise moment at leftend support is taken as negative; it will cause hogging moments in the beam, whereas at the
rightend support the clockwise moment is taken as positive which causes hogging.
(ii) All the distances should be measured with reference to the origin of axes which is taken at the extreme left end of the beam. All the distances should be entered in
meter and load in kN. It will give the values of BM in kNm and SF in kN.
(iii) You can also quickly get the B.M. values at different sections of the beam, just by changing the position of section.
(iv) In case of more than one load, take the sum of the results of all the cases (apply principle of superposition). Calculated values can be used to plot the bending
moment diagram.
(v) This calculator can also be used to find the ordinates of influence line diagram (http://civilengineer.webinfolist.com/str/ild.htm) for structures
(http://civilengineer.webinfolist.com/structure.htm).
Select from the following links to start calculation
Point Load on the beam
(http://civilengineer.webinfolist.com/fb/fbcalcp.php)
UVL maximum at center
(http://civilengineer.webinfolist.com/fb/fbcalcvc.php)
UDL on full span
(http://civilengineer.webinfolist.com/fb/fbcalcuf.php)
UVL maximum at left support
(http://civilengineer.webinfolist.com/fb/fbcalcvl.php)
UDL on left side
(http://civilengineer.webinfolist.com/fb/fbcalcul.php)
UVL maximum at right support
(http://civilengineer.webinfolist.com/fb/fbcalcvr.php)
UDL on right side
(http://civilengineer.webinfolist.com/fb/fbcalcur.php)
Moment applied on the span
(http://civilengineer.webinfolist.com/fb/fbcalcm.php)
Uniform Load on part of span New
This case is developed by using the principle of superposition and the above three cases of uniform load
(http://civilengineer.webinfolist.com/fb/fbcalcu.php)
Search our website for more...
Search
Like 0 Share
Tweet
Share
Excellent Calculators
Bending Moment Calculator (/mech/bmcalc.htm)
Calculate bending moment & shear force for simply supported beam
Moment of Inertia Calculator (/str/micalc.htm)
Calculate moment of inertia of plane sections e.g. channel, angle, tee etc.
Reinforced Concrete Calculator (/design/beamanalysis.htm)
Calculate the strength of Reinforced concrete beam
Civil Engineering …
271K likes
Like Page
1 friend likes this
Moment Distribution Calculator (/mdcalc.htm)
Solving indeterminate beams
Deflection & Slope Calculator (/str/sdcalc.htm)
Calculate deflection and slope of simply supported beam for many load cases
Fixed Beam Calculator (/fbcalc.htm)
Calculation tool for beanding moment and shear force for Fixed Beam for many load cases
BM & SF Calculator for Cantilever (/mech/bmcalc2.htm)
Calculate SF & BM for Cantilever
Deflection & Slope Calculator for Cantilever (/str/sdcalc.htm)
For many load cases of Cantilever
Overhanging beam calculator (/ohbcalc.htm)
For SF & BM of many load cases of overhanging beam
More Links