Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
D-326
To Order
Previous Datasheet Index Next Data Sheet
Bulletin I25190/B
ST700C..L SERIES
PHASE CONTROL THYRISTORS Hockey Puk Version
Features 910A
Center amplifying gate
Metal case with ceramic insulator
International standard case TO-200AC (B-PUK)
Typical Applications
DC motor control
Controlled DC power supplies
AC controllers
IT(AV) 910 A
@ Ths 55 °C
IT(RMS) 1857 A
@ Ths 25 °C
@ 60Hz 16400 A
2
I t @ 50Hz 1232 KA2s
tq typical 150 µs
TJ - 40 to 125 °C
D-327
To Order
Previous Datasheet Index Next Data Sheet
ST700C..L Series
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage V DRM /V RRM , max. repetitive VRSM , maximum non- I DRM /I RRM max.
Type number Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max
V V mA
12 1200 1300
16 1600 1700
ST700C..L 18 1800 1900 80
20 2000 2100
22 2200 2300
On-state Conduction 12
D-328
To Order
Previous Datasheet Index Next Data Sheet
ST700C..L Series
D-332
To Order
Previous Datasheet Index Next Data Sheet
ST700C..L Series
D-333
To Order
Previous Datasheet Index Next Data Sheet
ST700C..L Series
Switching
Parameter ST700C..L Units Conditions
di/dt Max. non-repetitive rate of rise Gate drive 20V, 20Ω, t ≤ 1µs
1000 A/µs r
of turned-on current TJ = TJ max, anode voltage ≤ 80% VDRM
Gate current 1A, di /dt = 1A/µs
t Typical delay time 1.0 g
d V = 0.67% VDRM, TJ = 25°C
µs d
ITM = 750A, TJ = TJ max, di/dt = 60A/µs, VR = 50V
t Typical turn-off time 150
q dv/dt = 20V/µs, Gate 0V 100Ω, t = 500µs
p
Blocking
Parameter ST700C..L Units Conditions
Triggering
23
Parameter ST700C..L Units Conditions
PGM Maximum peak gate power 10.0 TJ = TJ max, t ≤ 5ms
p
W
PG(AV) Maximum average gate power 2.0 TJ = TJ max, f = 50Hz, d% = 50
IGM Max. peak positive gate current 3.0 A TJ = TJ max, t ≤ 5ms
p
+VGM Maximum peak positive
20
gate voltage
V TJ = TJ max, t ≤ 5ms
-VGM Maximum peak negative p
5.0
gate voltage
TYP. MAX.
200 - TJ = - 40°C
IGT DC gate current required
100 200 mA TJ = 25°C
to trigger Max. required gate trigger/ cur-
50 - TJ = 125°C rent/ voltage are the lowest value
which will trigger all units 12V
2.5 - TJ = - 40°C
VGT DC gate voltage required anode-to-cathode applied
1.8 3.0 V TJ = 25°C
to trigger
1.1 - TJ = 125°C
D-329 3333
To Order
Previous Datasheet Index Next Data Sheet
ST700C..L Series
∆RthJ-hs Conduction 12
(The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC)
Sinusoidal conduction Rectangular conduction
Conduction angle Units Conditions
Single Side Double Side Single Side Double Side
180° 0.009 0.009 0.006 0.006
120° 0.011 0.011 0.011 0.011
90° 0.014 0.014 0.015 0.015 K/W TJ = TJ max.
60° 0.020 0.020 0.021 0.021
30° 0.036 0.036 0.036 0.036
Device Code
ST 70 0 C 22 L 1
1 2 3 4 5 6 7 8
1 - Thyristor
2 - Essential part number 2222222222222
3 - 0 = Converter grade
4 - C = Ceramic Puk
5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table)
6 - L = Puk Case TO-200AC (B-PUK)
7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads)
1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads)
2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads)
3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8 - Critical dv/dt: None = 500V/µsec (Standard selection)
L = 1000V/µsec (Special selection)
D-330
To Order
Previous Datasheet Index Next Data Sheet
ST700C..L Series
Outline Table
34 (1.34) DIA. MAX.
0.7 (0.03) MIN.
TWO PLACES
2 7 (1 .0 6 ) M AX .
PIN RECEPTACLE
AMP. 60598-1
0.7 (0.03) MIN. 53 (2.09) DIA. MAX. Case Style TO-200AC (B-PUK)
All dimensions in millimeters (inches)
20°± 5°
4.7 (0.18)
5 8 .5 (2 .3 ) D IA. M AX .
23
36.5 (1.44)
D-331 3333
To Order