Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Koji OKI
JFE Steel Corporation
Jan. 11st, 2018
1. Introduction
-Trend/History/Applications-
4. Conclusion
2 20 20
0 0 0
1955
1960
1965
1970
1975
1980
1985
1990
1995
2000
2010
↑ ↑ ↑ ↑ ↑
Tokachi Miyagi New Kobe Revised
Earthquake Earthquake Seismic Code Earthquake Seismic Code
Copyright © 2018 JFE Steel Corporation. All Rights Reserved.
Design Application of TMCP & High Strength Steels
High-rise building projects
* Outrigger truss
* Mega column (composite)
* Transfer girder
* King-post (steel & composite)
1. Introduction
-Trend/History/Applications-
4. Conclusion
Section
140mm 100mm
Size
1000mm 1000mm
140mm 100mm
(Encased-
(Encased-Steel) Section Area Section Area
Axial 3248 cm2 2400 cm2
Design
Strength Axial Design Strength Axial Design Strength
95,800kN 96,000kN
※Design Code: Eurocode4 ※Design Code: Eurocode4
Unit Weight 2550kg/m 1880kg/m 25% Saving!!
50% Saving!!
Flange Flange
Site-
Site-Weld
140mm 100mm
62cm2 33cm2
(207pass) (110pass)
50% Saving!!
Copyright © 2018 JFE Steel Corporation. All Rights Reserved.
TMCP Design Practice (Steel member)
Typical Application of S460M for Structural members
Member Profile Remark
(Steel) Welded-H / Box etc. *S460M welded-shape is one of the
most effective materials
in reducing the member size of
・Column extra-large section.
Large H-shape
⇒ Cost saving in strct. steel
Box shape
・Truss w/ wider-flange ⇒ Reduction in site-job workload
-element ex. Site-welding, Crane-lifting
Large H-shape
w/ Thin-web
・Transfer & Thick-flange
-girder
Profile shape & dimensions
can be tailored to the design
-constraints of individual prj.
1500mm (d)
Girder depth
B=400mm / Tf=30mm
Tw=15mm
Allowable point load (P) kN
1. Introduction
-Trend/History/Applications-
4. Conclusion
(Singapore practice)
Prj-A: Encased-steel S460M-120mm/thk
Prj-B: Encased-steel S460M-110mm/thk
etc.
http://www.jfe-steel.co.jp/release/2015/04/150420.html
Copyright © 2018 JFE Steel Corporation. All Rights Reserved. 18
Material Standards –S500-690Q / SBHS500-
Minimum Yield Tensile Strength
Strength (N/mm2) (N/mm2) Elongation Impact
Designation
≦50 ≦100 ≦150 ≦50 ≦100 ≦150 (%) Energy (J)
(16≦
≦) (16≦
≦)
Q -20 ℃ 27≦
≦
EN10025-6 min. min. min. 540 Min.17
QL 590-770 (Lo=5.65√So)
-40 ℃ 27≦
≦
S500 500 480 440 -720
QL1 -60 ℃ 27≦
≦
Q -20 ℃ 27≦
≦
EN10025-6 min. min. min. 770 760 710 Min.14
QL (Lo=5.65√So)
-40 ℃ 27≦
≦
S690 690 650 630 -940 -930 -900
QL1 -60 ℃ 27≦
≦
JIS G3140 Min20
Min.500 --- 570 - 720 --- (JIS #4)
-5℃ 100≦
SBHS500
Minimum Yield Strength
S690Q
S690Q:63% higher than S460
(N/mm2)
S500Q ▽SBHS500(TMCP)
S460M
S500Q:20% higher than S460
Slenderness λ
Reference: Murakami et al, AIJ-2009.8 Proceedings, #1332
Copyright © 2018 JFE Steel Corporation. All Rights Reserved. 24
Design Case Study (S500Q) -truss compression member-
Original Section Reduction of Steel Weight
Alternative section of S500Q
BU-600x500x100x120(S460M)
was found to be smaller by 20%,
500
while maintaining equivalent
strength.
600
t1=100
Original Alternative
H-600x500 S460M S500Q
Py(N/mm 2 ) 385 480
Web t1(mm) 100 74
Flange t2(mm) 120 95
area (mm2) 158000 125340 (0.8)
Axial Strength
60060 kN 60,160 kN
(Py x Area)
Weld-
Weld-joint of S500Q was prepared in similar conditions to those of S460M
Weld material Tensile strength Tensile strength Toughness
(SAW) (weld joint) (weld DEPO)
Wire JIS 3183 670N/mm2 635N/mm2 Ave.104 J
Ave.104
& flux S624-H3
引張試験写真