Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
I. LOCATION REQUIREMENTS
Duct Smoke Detector Location
Requirements: To prevent false alarms the detectors should
not be mounted in areas of extreme high or low temperatures,
in areas where high humidity exist, or in areas where duct air
may contain gases or excess dust. The duct detector should,
when possible, be located a minimum of six duct widths
downstream from a source of turbulence (bends, inlets, or
deflection plates). At these locations, air flow is less turbulent
and the air/smoke mixture should be more homogenous.
Refer to NFPA 90A, 72, and 101 for more information. See
Figure 1A and 1B.
Exception: Where it is physically impossible to locate
the duct detector accordingly, the duct detector can be
positioned closer than six duct widths, but as far as
possible from inlets, bends, or deflection plates.
Installation Instructions (P/N 1700-09882 HA-06-094) Page 1 of 3 Specifications subject to change without notice. * September 2014
SPECIFICATIONS
SPECIFICATIONS RATING
SD505-DUCT SD505-DUCTR
Alarm Relay Contact Rating 10A @ 24VDC
10A @ 115VAC
10A @ 240VAC
Trouble Relay Contact Rating 2.5A @ 30VDC
Operating Voltage 24VDC
Aux. Power Input Current 20mA Standby
62mA Alarm
SLC Input Current 0.5mA 0.5mA
Maximum SLC Resistance 50 Ohms 50 Ohms
Operating Temperature 32F ~ 100F 32F ~ 100F
Humidity 10% ~ 85% RH Non-Condensing 10% ~ 85% RH Non-Condensing
Air Velocity Rating 300 ~ 4000 ft./min. 300 ~ 4000 ft./min.
S (+)
TO NEXT
UL LISTED
SENSOR
SC (-)
+ -
ADDRESSABLE
LOOP
13 14 1 2 9 10 11 12
3 4 5 6 7 8
Test GND PILOT ALARM
SW LED LED
C C
REMOTE TEST NC NO NC NO
SWITCH
ALARM CONTACTS TROUBLE
UL LISTED SD505-DTS
10.0A @ 250VAC 10.0A @ 250VAC
CONTROL PANEL
(Test function only. Does not reset.)
S (+)
A.A. TO NEXT SENSOR
ANALOG ADDRESSABLE
CONTROL OR RETURN
PANEL SC (-) FIELD LOOP WIRING
TO CONTROL PANEL
Terminate Remote Accessories as indicated above (if required).
This is not a self-contained stand alone detector.
A U.L. Listed Analog Addressable Fire System is required.
Installation Instructions (P/N 1700-09882 HA-06-094) Page 2 of 3 Specifications subject to change without notice. * September 2014
SD505-DUCTR AND SD505-DTS-K
WIRING CONNECTIONS
CAUTION: FOR TERMINALS 3,4,5,6,7,8 DO NOT USE LOOPED WIRE UNDER TERMINALS. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTION. TEST GND PILOT ALARM
LED LED
24 VDC NC COM NO NC COM NO TEST GND PILOT ALARM SLC- SLC+
(+) (-) ALARM TROUBLE SW LED LED
YB E YB E YB E YB E YB E
BJ
9 W7 4 4 2
5
A
2127H1
+ BASE -
9 10
4 73
A7
5
4N 1P
9
105
A E DV
4 73 152
EBY
50K
4 73
730
037
K05
702
A7 2T 9 10
5
501
152
1V H
MADE IN INDONESIA
4 73
N4
75M
1 05
730
50K
105
RG4
LM3
93
CR7
Bot t om View
730
50K
105
3 35
2 004
4 74
4 73
2 004
4 73
4 74
725
D2
17
4 71 2 004
S
V104
MM
76A
5 1 05
1 05
A7
1 53
4 73
A7
4 73
5 4 73
725
D2
17
1V H
105
4 72
50K
730
1 53
4 73
4 73
152
2 004
1V H
1P
4 72
2T
9 1 04 E6 1
01
376
2T
725S
D217
1P
BJ
5
9 V104
1 53
A7
152
1 04
1 53
1 02
5 1 05
103
207 673
G43
C2K
1 05 10
16E
SC- S+ SC- S+
SLC OUT SLC IN
TEST GND PILOT ALARM SLC- SLC+
SW LED LED
Class A (Style 6) Wiring YB E YB E
EBY
by Honeywell
12 Clintonville Road
Northford, CT 06472
Installation Instructions (P/N 1700-09882 HA-06-094) Page 3 of 3 Phone: 203-484-7161 * Fax: 203-484-7118 Specifications subject to change without notice. * September 2014