Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Common
PROGRAMMERS
Neutral
Spare
Earth
SWITCHING LP711 – a 7-day program, allowing for different
Live
LP112 – a 24hr program, with linked central heating and hot
On
Off
MAKE MODEL
Current Models timings on each day of the week, up to 3 heating periods water on for up to 3 heating periods each day, and every day
ON 1 – start of first timed period
each day. the same.
Drayton Tempus 1, 2 (new models) N L 1 3 2 4
SINGLE DUAL SINGLE DUAL OFF 1 – end of first timed period If the engineer has set your program and timings – you If the timings haven’t been set for you, then your programmer
Lifestyle LP111, LP711 N L 1 3 2 4 Want to leave a timing as it is? Just press SET? and move on wont need to do anything else. Just keep this guide in a safe will still be on the factory-set standard 24hr program, with
CHANNEL CHANNEL Switchmaster 300 N L 4 1 CHANNEL CHANNEL ON 2 – start of second timed period to the next one. place for future reference. central heating and hot water operating together on the
Timeswitch Programmer Discontinued/Competitors’ Models Timeswitch Programmer OFF 2 – end of second timed period If you need to reset your timings to the standard program and same settings for every day of the week. But it’s easy to
ACL TC (Towerchron) 2 1 4 7 start again, press ‘SET’ and ‘+’ together to go back to the INTRODUCTION make changes – just follow the instructions.
for heating OR hot water for heating AND hot water Drayton Tempus 1, 2 (old models) N L 1 2 3 4 for heating OR hot water for heating AND hot water ON 3 – start of third timed period pre-set program. Want to leave a timing as it is? Press SET? and move on to
Switchmaster 980 N L 4 1 Lifestyle programmers will automatically switch your central the next one.
OFF 3 – final switch-off of the day
Danfoss Randall TS15, 75 (Mk18) E N L 1 4 2 5/6 heating and hot water on and off at times that suit you.
If you need to reset your timings to the standard program
Danfoss Randall TS715 E N L 1 4 2 3 The standard program Depending on your system, central heating and hot water can and start again, press ‘SET’ and ‘+’ together to go back to
If the engineer has set your program and timings – you won’t
Danfoss Randall TS975 E N L 5 4 6 1,2,3 either both come on and off at the same time, or work
need to do anything else. Just keep this guide in a safe place Your system will come on for up to 3 heating periods every the pre-set program.
Danfoss Randall SET1, SET1E E N L 5 4 6 independently. The red light on the front of the programmer
Danfoss Randall SET4 E N L 5 4 6 for future reference. 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. If you don’t press anything for two minutes, the programmer
shows whem each one is on automatically goes back to normal operation.
Danfoss Randall 103, 103E, 103E5, 103E7 4 5 6 3 1 2 Notice that ON2 and OFF2 are set to the same time.* This
Danfoss Randall 911, 971 E N L 5 6 4 2 DAY-TO-DAY VARIATIONS means your system won’t respond, but if you want to activate There are 4 models in the Lifestyle range:
Grasslin Towerchron QE1 N L 2 4 3 that middle period or change any other timings – read on. The standard program
Grasslin Towerchron T2001, T2001Q E N L 7
Sometimes you might need to change the way you use your I LP112 – a 24hr program, with linked central heating and hot Your system will come on for up to 3 heating periods every
Honeywell ST 6100A, ST 6100C N L 1 4 2
system temporarily – perhaps due to an exceptionally cold day. water on for up to 3 heating periods each day, and every day 24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Honeywell ST 7000B L 3 2
the same. Notice that on the standard program ON2 and OFF2 are set
Horstmann Centaur SC1, SC7 N L 4 3
Here’s how to do it – without affecting the timings in your
I LP241 – a 24hr program, with central heating and
LP111, LP711 LP112, LP241, LP522, LP722 LP111, LP711 LP112, LP241, LP522, LP722 STANDARD PROGRAM to the same time.* This means your system won’t respond,
Horstmann Centaur Plus, C11, C17 N L 2 4 3
program. SWITCHING but if you want to activate that middle period, or change any
Horstmann Emerald 423, Pearl Auto E N L 3 4
MON-FRI SAT-SUN hot water working independently for up to 3 heating periods other timings – read on.
Horstmann 517, Coronet, H11, H17 E N L 5 4 6
Landis & Staefa RWB3 N L 4 3 Switching on and off each day, and every day the same.
8.30am
7.00am
9.00am
I LP522 – a 5/2-day program allowing for different SWITCHING STANDARD PROGRAM
H/W on
H/W off
Neutral
C/H on
C/H off
Over-riding the program
Earth
Live
6.30am
I If, after you’ve set OFF3 you want to fine-tune one or more
central heating or hot water temporarily – perhaps due to an
unusually cold day, or exceptional demand for hot water.
same timings for every day of the week. But it’s easy to make
changes, and have heating and water working independently
* Can simply be removed from the backplate and replaced without any disturbance to the existing wiring. weekdays, press SET? until you find the first day you want to – just follow the instructions.
Here’s how to do it – without affecting your program.
OFF 1 – end of first timed period 8.30am adjust – then go through the procedure, altering any time you Want to leave a timing as it is? Press SET? and move on to
wish. Press SET? to move on to the next day. When you’ve Switching on and off the next one.
BEFORE INSTALLATION WIRING THE TIMESWITCH INTRODUCTION ON 2 – start of second timed period* 12.00pm
finished, press SET? until you see ‘SET SAT SUN PROG?’. If you need to reset your timings to the standard program
On the front of the programmer there are two Advance/Boost
First, make sure the mains supply is switched off! OFF 2 – end of second timed period* 12.00pm and start again, press ‘SET’ and ‘+’ together to go back to
Lifestyle Timeswitches will automatically control your system buttons – one for central heating and one for hot water. They the pre-set program.
Make the wiring connections as allow you to switch your system either on or off, irrespective of
PROGRAMMER ONLY by switching it on and off at times that suit you. The red light ON 3 – start of third timed period 4.30pm If you don’t press anything for two minutes, the programmer
above. Note that the output the program. So if the heating or hot water is off, and you want
on the front of the timeswitch shows when it’s on. automatically goes back to normal operation.
The programmer must be set to the type of system it is to con- contacts are voltage-free, so OFF 3 – final switch-off of the day 10.30pm warmth or hot water now, you can either –
I LP111 – a 24hr program, up to 3 heating periods
power needs to be put on to
I If you don’t want to alter any individual days, keep pressing
trol. The link on the back of the unit has two settings – P and G. The standard program
1. Press Advance to switch it on (ADV will be displayed), and it
Terminal 1 either by linking from Changing the timings
P = a fully pumped and controlled system – allowing each day, and every day the same. will stay on until the end of the next period. Or if the heating/hot Your system will come on for up to 3 heating periods every 24hrs.
Terminal L or from a separate SET? until you see ‘SET SAT SUN PROG?’.
heating and hot water to be set separately.
supply with a 3A fuse. I LP711 – a 7-day program, allowing for different I Press the SET? button and you’ll see ‘SET PROG?’. water is on and you don’t need it, press Advance and it will go ON1 starts the first one, OFF1 finishes it, and so on. Notice that on
Set weekend off until the beginning of the next ON period. the standard program ON2 and OFF2 are set to the same time for
G = a gravity-fed hot water system – which does not allow timings on each day of the week, up to 3 heating periods both central heating and hot water. * This means your system won’t
independent setting of heating without hot water, though each day. Advance will only operate in TIMED or ONCE modes. respond, but if you want to activate that middle period, or change
hot water can be controlled alone. any other timings – read on.
If the engineer hasn’t set your timings for you, your timeswitch 2. Press & Hold Boost to switch on for an extra hour ( & BST will
WIRING THE PROGRAMMER be displayed), then Press again for two ( ) or three ( ) hours.
will work with a standard program that has been set at the
USING AN EXISTING WALL-PLATE
USING A DRAYTON SIMP-L-FIT, ALTHOUGH NOT factory. If this doesn’t suit you, it’s very easy to change it – I Press the YES button, and you’ll see ON1, the start of your To cancel Boost, Press Boost again ( ). Or if the heating/hot STANDARD PROGRAM
Loosen the securing screws on the old programmer and NECESSARY, WILL MAKE THIS INSTALLATION EASIER. when you’ve read this introductory section, simply turn to first heating period. Adjust it in 1-minute steps using the – I Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3 water is already on, using Boost will extend the ON time by one, SWITCHING
and + buttons. If the – and + buttons are held down, the two or three hours. CH HW
unplug it. Check that there’s 70mm clearance to the right of the page for your timeswitch model. times in the same way.
the wall-plate, and 25mm above it. Check the chart on the time changes in 10-minute steps.
Connection Charts Over-riding the program ON 1 – start of first timed period 6.30am 6.30am
next page to compare terminals and if necessary, change the Set each day
Arrowed numbers relate to OFF 1 – end of first timed period 8.30am 8.30am
wiring of the wall-plate to suit. Now plug the Lifestyle unit into
the junction box. I If, after you’ve set OFF3 for both SAT & SUN, you want to fine-
the wall-plate and tighten the securing screws. ON 2 – start of second timed period* 12.00pm 12.00pm
tune Saturday or Sunday, press SET? until you find the first day
Consult boiler handbook you want to adjust – then go through the procedure, altering any OFF 2 – end of second timed period* 12.00pm 12.00pm
Check the 3A fuse, and switch on the mains.
I Press SET?, and you’ll see OFF1, the end of your first heating
for details of pump Remember:
time you wish. Press SET? to move on to the next day. When ON 3 – start of third timed period 4.30pm 4.30pm
I Make your changes using the SET?, YES/-, and + buttons.
overrun wiring. On each side of the display there are four operating modes –
FITTING A NEW WALL-PLATE period. Adjust this in the same way, press SET?, then repeat the you press SET? after setting your hot water for Sundays, the pro-
one group for central heating, the other for hot water. You can OFF 3 – final switch-off of the day 10.30pm 10.30pm
I You can’t set ON1 as the last timing before midnight, but you
procedure for ON2, OFF2, ON3 and OFF3. grammer will go back to normal operation.
*Thermostat Key Wiring Colour Codes change modes with immediate effect by using the appropriate
The ideal location is 1.4m above floor level, with reasonable C Common GR Grey can set OFF3 after midnight – providing it’s not more than 23 SELECT button. This won’t alter the timings in your program,
lighting, good access, no condensation, no extremes of H Call for Heat Y Yellow Changing the timings
hours and 59 minutes after ON1. which you can return to by selecting TIMED.
BK Black
I Press the SET? button and you’ll see ‘SET PROG?’.
temperature, and a supporting surface that fully covers the S Satisfied
I You need to set the timings in sequence – i.e. ON1, OFF1, ON2,
N Neutral BL Blue SAT
back of the unit. BR Brown
E Earth OFF = continuously off.
Position with 70mm clearance to the right, 25mm above, and RD Red OFF2, ON3, OFF3. If you get out of sequence, the display will
I When you press SET? after setting OFF3, the timeswitch will I If you don’t want to alter either day, keep pressing SET?
L Live
W White flash a warning. TIMED = on for up to 3 periods a day.
sufficient room to access the securing screws underneath. OR Orange return to normal operation. until the programmer goes back to normal operation. ONCE = on for 1 period a day, from the start of ON1
Fix, with terminals at the top, either direct to a flat wall using wall YG Yellow/Green
to the end of OFF3.
plugs and No. 6 x 1” (25mm) woodscrews, or on a flush mount-
ing single conduit box type UA1 (BS4662) using M3.5 x 14 bolts. ON = continuously on.
DO NOT USE A SURFACE MOUNTING BOX.
06490033001 IssH:Invensys B/sheet_TO PRINT 8/9/10 14:08 Page 2
THE LP241 24hr ELECTRONIC PROGRAMMER Cont... THE LP522 5/2-DAY ELECTRONIC PROGRAMMER Cont... THE LP722 7-DAY ELECTRONIC PROGRAMMER Cont... SETTING THE CLOCK Cont... WIRING THE PROGRAMMER Cont...
I When you press SET? after setting OFF3 for the weekday central
Set the minute
Connection Charts
I Press SET?, and the minutes will start to flash. Use the – and +
Set the central heating Set weekday hot water
heating, the display will ask ‘SET HW MON to FRI PROG?’.
I Press the YES button, and the display will ask ‘SET CH PROG?’. I When you press SET? after setting OFF3 for the central heating, buttons to set the exact time.
the display will ask ‘SET HW MON to FRI PROG?’.
I When you press SET? after OFF3 for the weekend central If you don’t want to alter any individual days, keep pressing Set the year
Set the hot water SET? until you see ‘SET SAT SUN PROG?’.
I Press YES and the year will start to flash. Use the – and + but-
heating, the display will ask ‘SET HW SAT SUN PROG?’.
I When you press SET? after setting OFF3 for the central heating, Press YES, and follow the procedure. tons to adjust.
I When you press SET? after OFF3 for HW SAT SUN, the
the display will ask ‘SET HW PROG?’.
programmer will go back to normal operation.
I Press YES to SET H’DAY? and the display will show ‘00’.
7 L
LWC3
Set all weekdays
1
I Using + and -, set the number of days you want the system to
L 1 7 5 2 3 1 7 6 2 3
Changing the timings First you set the times that are going to be the same for each N 2
E 3
I Press the SET? button and you’ll see ‘SET PROG?’.
weekday, then you can select each day individually and make be off.
any further adjustments. If you want each day to be quite differ-
I Press SET, the display will show ‘H’DAY’ and the programmer
Switched and Fused
GR OR BR BL YG GR OR BR BL YG BOILER
ent, go straight to ‘Set each day.’ (3A) Mains input
CH VALVE DHW VALVE 3 E †
will switch off the system. It will then return to normal operation
I Press the YES button, and the display will ask ‘SET MON to FRI
2 N
after the set number of days. LIFESTYLE 679H308-30L1 7 L
PROG?’. LIFESTYLE 779H33530L10
DRAYTON ZV22
Remember - The programmer counts each pass through Honeywell
Set the weekday central heating
midnight as a day. So if on a Saturday morning you don’t want † For pump overrun boilers consult V4043H1056
I Press the YES button, and the display will ask ‘SET CH MON to the heating on again until Tuesday morning, set for 3 days. manufacturer's instructions Landis & Gyr
ZAV222
FRI PROG?’. * See Thermostat Key
SETTING THE CLOCK AND DATE
I Press YES and the display will ask ‘SET CH MON to FRI
PROG?’. Applicable to all models.
Make the wiring connections, as above, for the appropriate system.
SETTING THE CLOCK INSTALLERS/ENGINEERS NOTES
I Press YES and you’ll see ON1, the start of your first central heat-
For surface wiring, snap out the cable entry strip on the bottom edge
of the wall-plate. Lifestyle units are double-insulated and need no earth
ing period. Adjust it in 1-minute steps using the – and + but- The clock in your programmer has been set at the factory,
connection, but an earthing continuity (loop) terminal is provided for
tons. If the – and + buttons are held down, the time changes in and automatically accounts for British Summer Time. convenience.
I Press YES, and you’ll see ON1, the start of your first central
10-minute steps. However, should you need to set the clock, read on.
I Press SET?, and you’ll see OFF1, the end of your first central
THE LIFESTYLE TIMESWITCH/PROGRAMMER – AND
NEVER FIT IT TO A LIVE WALL-PLATE!
heating period. Adjust this in the same way, press SET?, then
repeat the procedure for ON2, OFF2, ON3 and OFF3. Set the hour
I Press YES once, and then the hour will start to flash. Use the
I Press SET?, and you’ll see OFF1, the end of your first central
– and + buttons to set the hour, checking for AM and PM.
heating period. Adjust this in the same way, press SET?, then
repeat the procedure for ON2, OFF2, ON3 and OFF3.