Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
i7610
Thank you for choosing this Icom product. The IC-7610 HF/50 MHz TRANSCEIVER is designed and built with
Icom’s state of the art technology and craftsmanship. With proper care, this product should provide you with
years of trouble-free operation. We appreciate you making the IC-7610 your transceiver of choice, and hope you
agree with Icom’s philosophy of “technology first.” Many hours of research and development went into the design
of your IC-7610.
DISPOSAL
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in
the European Union, all electrical and electronic products, batteries, and accumulators
(rechargeable batteries) must be taken to designated collection locations at the end of their
working life. Do not dispose of these products as unsorted municipal waste.
Dispose of them according to the laws in your area.
ii
ABOUT THE TOUCH SCREEN
DD Touch operation DD Touch screen precautions
In the Full manual or Basic manual, the touch ••The touch screen may not properly work when the
operation is described as shown below. LCD protection film or sheet is attached.
••Touching the screen with your finger nails, sharp
Touch topped object and so on, or touching the screen
If the display is touched briefly, one short beep hard may damage it.
sounds. ••Tablet PC’s operations such as flick, pinch in and
pinch out cannot be performed on this touch screen.
A PC with the following Operating System is required. Installs Adobe® Acrobat® Closes the Menu screen
Reader®
••Microsoft® Windows® 10
••Microsoft® Windows® 8.1
••Microsoft® Windows® 7 LDifferent types of menu screen may be displayed,
depending on the transceiver version.
iii
ABOUT THE CONSTRUCTION OF THE MANUAL
There are two different types of manuals for this transceiver, the Basic manual (this manual) and the Advanced
manual.
And more....
iv
ABOUT THE INSTRUCTIONS
The Basic and Advanced manuals are described in Detailed instruction
the following manner.
1. Push MENU .
“ ” (Quotation marks):
Used to indicate icons, setting items, and screen titles
displayed on the screen.
The screen titles are also indicated in uppercase
letters. (Example: FUNCTION screen)
[ ] (brackets):
Used to indicate keys.
MENU
Instruction example
vi
TABLE OF CONTENTS (Continued)
Operating CW.................................................. 4-10 9. CLOCK AND TIMERS...................................... 9-1
DD Setting the CW pitch control...................... 4-10 Setting the date and time.................................. 9-1
DD Setting the keying speed........................... 4-11 DD Setting the date........................................... 9-1
DD Using the Break-in function....................... 4-11 DD Setting the current time............................... 9-1
DD Monitoring the CW side tone..................... 4-12 DD Setting the UTC offset................................. 9-1
DD APF (Audio Peak Filter) operation............ 4-12 DD Displaying CLOCK2.................................... 9-1
DD About the Electronic Keyer function.......... 4-13 DD Setting the CLOCK2 UTC offset.................. 9-2
DD Editing the CLOCK2 name.......................... 9-2
5. SCOPE OPERATION........................................ 5-1
Spectrum scope screen..................................... 5-1 10. MAINTENANCE.............................................. 10-1
DD Marker......................................................... 5-1 Resetting......................................................... 10-1
DD Using the Spectrum Scope......................... 5-1 DD Partial reset............................................... 10-1
DD Displaying the Mini scope screen................ 5-2 DD All reset..................................................... 10-1
Audio scope screen........................................... 5-2 Troubleshooting............................................... 10-2
DD Using the Audio scope................................ 5-2
11. SPECIFICATIONS.......................................... 11-1
DD AUDIO SCOPE SET screen........................ 5-3
DD General..................................................... 11-1
6. SD CARD/USB FLASH DRIVE........................ 6-1 DD Transmitter................................................ 11-1
About the SD cards........................................... 6-1 DD Receiver.................................................... 11-2
About the USB flash drive................................. 6-1 DD Antenna tuner............................................ 11-2
Saving data....................................................... 6-1
12. OPTIONS........................................................ 12-1
Inserting............................................................. 6-1
Formatting......................................................... 6-2 13. CONNECTOR INFORMATION....................... 13-1
DD Formatting the SD card or Interface information........................................ 13-1
USB flash drive........................................... 6-2 ACC sockets.................................................... 13-2
Unmounting....................................................... 6-2 PHONES......................................................... 13-3
ELEC-KEY....................................................... 13-3
7. ANTENNA TUNER OPERATION..................... 7-1
KEY................................................................. 13-3
About the Antenna memory settings................. 7-1
DC 13.8 V........................................................ 13-3
DD The Antenna memory screen...................... 7-1
TUNER............................................................ 13-3
DD Saving an antenna connector setting.......... 7-1
MIC.................................................................. 13-3
DD Selecting the antenna type.......................... 7-2
EXT KEYPAD.................................................. 13-4
About the internal antenna tuner....................... 7-2
REMOTE......................................................... 13-4
Using the Internal antenna tuner....................... 7-3
METER............................................................ 13-4
DD Manual tuning.............................................. 7-3
USB port (type A)............................................ 13-4
DD PTT Tuner start........................................... 7-3
ALC................................................................. 13-4
About an external antenna tuner....................... 7-3
SEND.............................................................. 13-4
DD Using the AH-4 or AH-740........................... 7-3
LAN................................................................. 13-5
DD Using an external antenna tuner................. 7-4
EXT-DISPLAY.................................................. 13-5
Emergency mode (Tuner).................................. 7-4
USB 2.............................................................. 13-5
8. SET MODE........................................................ 8-1 USB 1.............................................................. 13-5
Set mode description......................................... 8-1 EXT-SP A / EXT-SP B...................................... 13-5
DD Entering the Set mode................................ 8-1 REF IN............................................................. 13-5
Tone Control ..................................................... 8-2 X-VERTER...................................................... 13-6
Function............................................................. 8-2 ANT 1 / ANT 2................................................. 13-6
Connectors........................................................ 8-5 RX-ANT IN/OUT.............................................. 13-6
Network............................................................. 8-7
INSTALLATION NOTES............................................. I
Display............................................................... 8-8
Time Set............................................................ 8-9 INDEX........................................................................ II
SD Card............................................................. 8-9
USB Flash Drive.............................................. 8-10
Others.............................................................. 8-10
vii
PRECAUTIONS
R DANGER HIGH RF VOLTAGE! NEVER touch an CAUTION: DO NOT expose the transceiver to rain, snow
antenna or antenna connector while transmitting. This could or any liquids. They could damage the transceiver.
cause an electrical shock or burn.
CAUTION: DO NOT change the internal settings of the
R DANGER! NEVER operate the transceiver near transceiver. This may reduce transceiver performance and/
unshielded electrical blasting caps or in an explosive or damage the transceiver. The transceiver warranty does
atmosphere. This could cause an explosion and death. not cover any problems caused by unauthorized internal
adjustments.
R WARNING RF EXPOSURE! This device emits Radio
Frequency (RF) energy. Extreme caution should be CAUTION: DO NOT install the equipment in a place
observed when operating this device. If you have any without adequate ventilation, or block any cooling vents
questions regarding RF exposure and safety standards on the top, rear, sides or bottom of the transceiver or the
please refer to the Federal Communications Commission cooling fan. Heat dissipation may be reduced and damage
Office of Engineering and Technology’s report on the transceiver.
Evaluating Compliance with FCC Guidelines for Human
Radio Frequency Electromagnetic Fields (OET Bulletin 65). CAUTION: DO NOT use harsh solvents such as benzine or
alcohol when cleaning. This could damage the equipment
R WARNING! NEVER operate the transceiver with a surfaces. If the surface becomes dusty or dirty, wipe it clean
headset or other audio accessories at high volume levels. If with a soft, dry cloth.
you experience a ringing in your ears, reduce the volume or
discontinue use. CAUTION: DO NOT place or leave the transceiver in
areas with temperatures below 0°C (32°F) or above 50°C
R WARNING! NEVER apply AC power to the [DC13.8V] (122°F).
socket on the transceiver rear panel. This could cause a fire
or damage the transceiver. CAUTION: DO NOT place the transceiver in excessively
dusty environments, or in direct sunlight. This could
R WARNING! NEVER apply more than 16 V DC to the damage the transceiver.
[DC13.8V] socket on the transceiver rear panel. This could
cause a fire or damage the transceiver. CAUTION: DO NOT set the transceiver’s RF output power
to more than a connected linear amplifier’s maximum input
R WARNING! NEVER reverse the DC power cable level. Otherwise, the linear amplifier will be damaged.
polarity. This could cause a fire or damage the transceiver.
CAUTION: DO NOT use non-Icom microphones. Other
R WARNING! NEVER remove the fuse holder on the DC microphones have different pin assignments and may
power cable. Excessive current caused by a short could damage the transceiver.
cause a fire or damage the transceiver.
BE CAREFUL! The transceiver will become hot when
R WARNING! NEVER let metal, wire or other objects operating the transceiver continuously for long periods of
contact the inside of the transceiver, or make incorrect time.
contact with connectors on the rear panel. This could cause
an electric shock or damage the transceiver. NEVER leave the transceiver in an insecure place to avoid
use by unauthorized persons.
R WARNING! NEVER operate or touch the transceiver
with wet hands. This could cause an electric shock or Turn OFF the transceiver’s power and disconnect the DC
damage to the transceiver. power cable when you will not use the transceiver for long
period of time.
R WARNING! NEVER operate the equipment if you notice
an abnormal odor, sound or smoke. Immediately turn OFF The LCD display may have cosmetic imperfections
the power and/or remove the DC power cable. Contact your that appear as small dark or light spots. This is not a
Icom dealer or distributor for advice. malfunction or defect, but a normal characteristic of LCD
displays.
R WARNING! NEVER put the transceiver on an unstable
place where the transceiver may suddenly move or fall.
This could cause an injury or damage the transceiver.
viii
1 PANEL DESCRIPTION
Front panel
q r HEADPHONE JACK [PHONES] (p. 13-3)
Connects to standard stereo headphones.
w t ELECTRONIC KEYER JACK [ELEC-KEY] (p. 13-3)
!2 Connects to a paddle to use the internal electronic
e
r keyer for the CW operations.
o
y USB PORT [USB A] (p. 13-4)
t !1 Insert a USB flash drive, USB A type keyboard,
!0 RC-28 remote encoder, mouse or hub.
y
u MICROPHONE CONNECTOR [MIC] (p. 13-3)
o
Connects to the supplied or an optional microphone.
u
i SD CARD SLOT [SD CARD] (p. 6-1)
Accepts an SD card. The indicator next to the slot
lights blue when inserted.
i
o VOLUME CONTROL AF RF/SQL (p. 3-1)
q POWER KEY POWER (p. 3-1) L The upper control is for the Main band, and the
Turns the transceiver ON or OFF. lower control is for the Sub band.
• Push to turn the Mute function ON or OFF.
w TRANSMIT KEY TRANSMIT (p. 3-9) - The TX/RX indicator lights orange when the Mute
Toggles between transmit and receive. function is ON.
• Adjusts the audio output level.
RF GAIN/SQUELCH CONTROL AF RF/SQL (p. 3-7)
The TX/RX indicator Adjusts the RF gain and squelch threshold levels.
••Lights green while receiving. !0 NOISE REDUCTION KEY NR (p. 4-5)
••Lights red while transmitting. Turns the Noise Reduction function ON or OFF.
!1 NOISE BLANKER KEY NB (p. 4-5)
e TIMER KEY TIMER Turns the Noise Blanker ON or OFF.
Turns the Sleep Timer or Daily Timer function ON or !2 ANTENNA TUNER KEY TUNER (p. 7-3)
OFF. Turns the antenna tuner ON or OFF, or activates
the tuner.
!3 !4 !5 !6 !7 !8 !9 @0 @1
!3 MENU KEY MENU (p. 8-1) !6 MEMO PAD READ KEY MP-R
Displays the MENU screen. Sequentially calls up the contents in the Memo Pad.
!4 MINI SCOPE KEY M.SCOPE (p. 5-2) !7 AUTO TUNE KEY AUTO TUNE (p. 4-8)
Displays the Mini Scope or Spectrum Scope. Automatically tunes the operating frequency to a
received CW signal.
!5 MEMO PAD WRITE KEY MP-W
Saves the displayed contents into the Memo Pad. !8 QUICK KEY QUICK (p. 1-7)
Displays the QUICK MENU.
1-1
PANEL DESCRIPTION 1
1-2
1 PANEL DESCRIPTION
Rear panel
q w e r t
!5 y
!6 !7 !8 !9 @0
u
!4 !3 !2 !1 !0 o i
1-3
PANEL DESCRIPTION 1
!6
!5 5
!6
6
7
!7
8
9
!8 10
q MULTI-FUNCTION KEY GROUP !2 BK-IN/F-BKIN INDICATOR (p. 4-11) 11
Displays the Multi-function keys. Displayed while the Semi Break-in or Full Break-in
w ANTENNA INDICATOR (p. 7-1)
function is ON. 12
Displays the selected antenna connector between !3 NET FUNCTION INDICATOR (p. 8-7)
ANT 1 and ANT 2. Displayed when the NET function is ON while in the 13
PSK mode.
e METER TYPE INDICATOR (p. 3-7)
Displays the selected transmit parameter type. !4 FREQUENCY OFFSET READOUT 14
Select between Po, SWR, ALC, COMP, Vd and Id. Displays the offset value between the PSK signal
r BANDWIDTH INDICATOR (p. 4-3, 4-4)
and the operating frequency, while a PSK signal is 15
received.
Displays the passband width of the IF filter.
!5 AFC FUNCTION INDICATOR
16
t SHIFT FREQUENCY INDICATOR (p. 4-3)
Displays the shift frequency of the IF filter.
Displayed while the Automatic Frequency Control
(AFC) function is ON, in the PSK mode.
17
y NOTCH INDICATOR (p. 4-6)
“AN” is displayed when the Auto Notch function is
!6 FREQUENCY READOUT (p. 3-4) 18
Displays the operating frequency.
ON, and “MN” is displayed when the Manual Notch
function is ON.
LThe non-selected band’s frequency readout (Main or
Sub) is displayed in gray.
19
u PASSBAND WIDTH INDICATOR (p. 4-3)
Displays the passband width for twin PBT operation
!7 FUNCTION DISPLAY 20
Displayed when an item that has a function display
and the center frequency for IF shift operation. is selected. For example, the Spectrum Scope. 21
i AUDIO PEAK FILTER (APF) INDICATOR (p. 4-12) !8 FUNCTION KEYS (p. 5-1)
Displayed when the Audio Peak Filter is ON. Displays the operating parameters, modes,
o CLOCK READOUT (p. 9-1) frequencies and indicators, and so on.
Displays the time (2 types) set on the TIME SET !9 VOX INDICATOR
screen. Displayed while the VOX function is ON.
!0 USB INDICATOR (p. 6-1) @0 VOICE RECORDER ICON
Displayed while a USB flashed drive is inserted. ••“●” is displayed while recording.
!1 LAN INDICATOR ••“” is displayed while pausing.
Displayed while the transceiver and the optional
RS-BA1 are connected through the LAN for remote
control operation.
1-4
1 PANEL DESCRIPTION
@5 @6 @7 @8 @9 #0 #1 #2 #3 #4 @1 @4 @3 @2 @6 @7 @8 @9 @5
@4
@3
@2
@1
#9 #8 #7 #6 #5 $1 $0 #9 #8 #7 #6 #5
1-5
PANEL DESCRIPTION 1
DDMENU screen 1
zzOpen the MENU screen by pushing MENU . 2
Function name
Status
3
4
Lights blue or orange
when in use 5
LThe items displayed on the menu differ, depending
on the selected operating mode.
6
7
8
DDMulti-function menus 9
Multi-function menu items
10
SSB CW RTTY PSK
RF POWER RF POWER RF POWER RF POWER 11
MIC GAIN
Touch to turn
DIGI-SEL DIGI-SEL DIGI-SEL DIGI-SEL 12
ON or OFF NOTCH NOTCH NOTCH NOTCH
NOTCH WIDTH NOTCH WIDTH NOTCH WIDTH NOTCH WIDTH 13
14
MONITOR MONITOR MONITOR
AM FM NB NR
RF POWER RF POWER LEVEL LEVEL
15
MIC GAIN MIC GAIN DEPTH
Multi-function menu
DIGI-SEL DIGI-SEL WIDTH 16
NOTCH NOTCH
zzOpen the Multi-function menu by pushing MULTI
(Multi-function control). NOTCH WIDTH 17
zzWhile the Multi-function menu is open, touch the MONITOR MONITOR
desired item and rotate MULTI to adjust the value. ATT VOX BK-IN COMP 18
LYou can open other menus by holding down NB LEVEL GAIN DELAY LEVEL
or NR for 1 second, or touching “ATT,” “VOX,” ANTI VOX TBW 19
“BK-IN” or “COMP” in the Multi-function key group DELAY
for 1 second. VOICE DELAY
20
21
1-6
1 PANEL DESCRIPTION
DDQUICK MENU
1-7
PANEL DESCRIPTION 1
Alphabet mode
Number mode
Symbol mode
1-8
1 PANEL DESCRIPTION
1. Display the MEMORY screen. 7. Touch [s], [p], [o], and then [t].
MENU » MEMORY 8. Touch [SPACE] to enter a space.
9. Touch [ab].
2. Touch the memory channel 2 for 1 second. ••The CHARACTER TYPE screen is displayed.
••The MEMORY MENU screen is displayed.
1-9
INSTALLATION AND CONNECTIONS 2
Using the desktop stands Heat dissipation
The transceiver has legs for desktop use. ••NEVER install the transceiver in a place without
zzPull-out the legs on both sides until they lock in adequate ventilation. Heat dissipation may be 1
place. reduced, and the transceiver may be damaged.
••DO NOT place the transceiver against walls or put 2
anything on top of the transceiver. This may block
airflow and overheat the transceiver. 3
••DO NOT touch the rear panel after transmitting
continuously for long periods of time. The panel may 4
become hot.
Fuse
GND
Red Black
2-1
2 INSTALLATION AND CONNECTIONS
NOTE:
••Before connecting, be sure to turn OFF the transceiver.
••While the AH-4 is connected, the IC-7610ʼs internal antenna tuner is deactivated.
[TUNER] [ANT 1]
GND
GND
Connecting a Transverter
Connect your transverter unit as described below.
LYou may need to connect to [ALC], depending on the transverter.
Transverter
RX RX
TRV RF IN/OUT Coaxial cable (50 Ω)
TX TX
ANT TRV
[SEND]
[X-VERTER]
[SEND]
GND
GND
••Set the “Transverter Function” item to ON to use the transverter operating mode.
You can also use the transverter operating mode by connecting a DC voltage to [ACC 2 (6: TRV)].
MENU » SET > Function > Transverter Function
LYou cannot select the antenna or use the internal tuner while using the Transverter function.
••Set the offset frequency for the transverter operation.
MENU » SET > Function > Transverter Offset
2-2
INSTALLATION AND CONNECTIONS 2
[REMOTE]
4
[INPUT 1] [ACC 2] 5
Coaxial cable (50 Ω)
6
[REMOTE] 7
[ANT 1]
EXCITER 8
1 1&2
9
GND
10
To an AC outlet 11
Non-European versions: 100~120/200~240 V
European version: 230 V 12
R WARNING! When using a linear amplifier such as the IC-PW1 or IC-PW1EURO, set the RF POWER in the Multi-function
menu to keep the ALC meter in the red zone.
13
LSee page 3-8 for details on the RF POWER settings.
LSee page 3-9 for details on the ALC zone settings. 14
15
DDConnecting a non-Icom linear amplifier
See the illustration below to connect a non-Icom linear amplifier. 16
LWe recommend that you use a linear amplifier with a specified input power of 100 watts or more. If you use an amplifier with
a specified drive level of less than 100 watts, adjust the IC-7610’s output power to the specified level before transmitting. 17
Otherwise the linear amplifier may be damaged.
To an antenna
18
[ANT1]
Non-Icom Coaxial cable (50 Ω) or 19
linear amplifier [ANT2]
20
RF OUT RF IN
ALC
21
SEND
GND
GND
[ALC] [SEND]
GND
R WARNING!
••The maximum signal level of the [SEND] jack is 16 V/0.5 A DC, and 250 V/200 mA with the “MOSFET” setting (p. 13-2).
Use an external unit if your non-Icom linear amplifier requires a control voltage and/or current greater than specified.
••The ALC input level must be in the range 0 to –4 V. The transceiver does not accept a positive voltage. Non-matched ALC
and RF power settings could overheat or damage the linear amplifier.
2-3
3 BASIC OPERATION
q
t
w
e y
MAIN DIAL
15
Main Sub
16
17
DDUsing the Dualwatch operation
The Main band is selected.
1. P
ush DUAL-W briefly to start the Dualwatch 18
operation.
••“DUAL-W” is displayed. 19
LTo equalize the Sub band frequency and mode
Displayed
3-2
3 BASIC OPERATION
10
11
L is displayed when you set an amateur radio
frequency, and (“TX” with a border of short 12
dashes) is displayed when you set a frequency
DDUsing the 1 Hz step Fine Tuning function
outside the Ham band, or outside your set Band
Edges. You can use the minimum tuning step of 1 Hz for
13
fine tuning in the SSB, CW and RTTY modes as the
default. 14
DDSetting the Tuning Step function 15
Touch the Hz digits for 1 second to turn the Fine
You can set MAIN DIAL ’s tuning step for each operating
Tuning function ON or OFF.
band. This is convenient to change the operating
frequency faster or slower. The following steps are set
16
as default.
17
••SSB/CW/RTTY/PSK (TS OFF): 10 Hz
••AM (TS ON):
••FM (TS ON):
1 kHz
10 kHz
18
ouch the kHz digits to turn the Tuning Step function
T 19
ON or OFF.
LThe Tuning Step function’s icon “▼” is displayed above
the 1 kHz digit when the function is ON.
The 1 Hz digit 20
is displayed.
21
LWhen using the [UP]/[DN] keys on the microphone,
the frequency changes in 50 Hz steps with the Fine
Tuning function ON or OFF.
3-4
3 BASIC OPERATION
2. Touch [F-INP].
••Opens the F-INP screen.
LIf you touch [ENT] when the digits under 100 kHz are
not entered, “0” will be automatically entered into the
digits that are blank.
Entry examples
••14.025 MHz: [1], [4], [•(−)], [0], [2], [5], [ENT]
••18.0725 MHz: [1], [8], [•(−)], [0], [7], [2], [5], [ENT]
••730 kHz: [0], [•(−)], [7], [3], [ENT]
••5.100 MHz: [5], [•(−)], [1], [ENT]
••7.000 MHz: [7], [ENT]
••Changing from 21.280 MHz to 21.245 MHz:
[•(−)], [2], [4], [5], [ENT]
3-5
BASIC OPERATION 3
Rotate AF RF/SQL (outer) to adjust the RF gain and DDSelecting the Meter readout
SQL level. Select one of the 6 different transmit parameters
(Po, SWR, ALC, COMP, Vd and Id) to display during
By default, rotating to the left (when set to the 12 transmit.
o’clock position) adjusts the RF gain, and rotating to
the right adjusts the squelch level, as described below. Touch the meter to display one of the meters.
is displayed
Maximum S-meter
Minimum RF gain Signal strength
squelch
Id
RF gain Power level
ou can adjust the receive sensitivity.
Y
••If a strong interfering signal is received, rotate
AF RF/SQL (outer) counterclockwise to reduce the
SWR
RF gain.
Compression level
L“RFG” is displayed to indicate that the gain is ALC level Vd
reduced.
LIf a strong signal is received and “OVF” (Overflow)
appears, reduce the RF gain until “OVF” disappears.
3-7
BASIC OPERATION 3
3-8
3 BASIC OPERATION
LLInformatio
•• In the SSB mode, touch the TX meter to select the
ALC meter, and adjust until the meter reading swings
between 30 to 50% of the ALC scale, when speaking
into the microphone at your normal voice level.
•• In the AM or FM mode, check the audio clarity with
another station, or use the Monitor function (p. 4-7).
3-9
RECEIVING AND TRANSMITTING 4
Preamplifiers RIT function
The preamps amplify received signals in the receiver The RIT (Receive Increment Tuning) function
front end to improve the signal-to-noise ratio and compensates for differences in the transmit 1
sensitivity. A preamp is used when the received frequencies of other stations.
signals are weak. The function shifts your Main bandʼs receive frequency 2
LEach band memorizes the previously used Preamplifier up to ±9.99 kHz without shifting your transmit
setting. frequency. 3
Touch [P.AMP].
1. Push RIT to turn ON the RIT function. 4
LEach touch sequentially selects “P.AMP 1,” “P.AMP 2,”
LWhile using the Fine Tuning function (p. 3-4), the RIT
and “P.AMP OFF.”
frequency is displayed in 4 digits, instead of 3. 5
RIT frequency 6
7
Wide dynamic range preamplifier.
P.AMP 1 It is most effective for the HF low bands.
••Gain is approximately 12 dB.
8
P.AMP 2
High-gain preamplifier.
It is most effective for the higher bands. 2. R
otate RIT/ TX to set the RIT frequency to match
9
••Gain is approximately 20 dB. the transmitting station’s frequency.
LYou can reset the RIT frequency to “0.00” by holding 10
NOTE: down CLEAR for 1 second.
••When you use the preamp while receiving strong LYou can add the frequency shift to your operating 11
signals, the receiving signal may be distorted. In such frequency by holding down RIT for 1 second.
case, turn OFF the preamp. 3. When you have finished communicating, push 12
••While the Digital Selector is ON, “P.AMP OFF” is fixed, RIT to turn the RIT function OFF.
and you cannot select “P.AMP 1” or “P.AMP 2.” 13
14
Attenuator RIT
15
The Attenuator prevents a signal from becoming
distorted when a very strong signal is being received 16
near your operating frequency, or when a very strong
electric field, such as from a broadcasting station. 17
ouch [ATT] to sequentially set the Attenuator up to 18
T
dB in 6 dB steps. DDUsing the RIT Monitor function
18
When the RIT function is ON, you can monitor your
operating frequency while holding down XFC . 19
LWhile monitoring: 20
••The RIT function is temporarily OFF.
••The Noise Reduction, Notch filter and Twin PBT 21
ou can also set the Attenuator in 3 dB steps:
Y settings are temporarily OFF.
1. Touch [ATT] for 1 second to open the ATT menu.
XFC
Displayed
2. R
otate MULTI to adjust the attenuator level of
up to 45 dB.
4-1
4 RECEIVING AND TRANSMITTING
4-2
RECEIVING AND TRANSMITTING 4
PBT1 18
PBT2
19
Cutting the Cutting both higher and 20
PBT is OFF lower passband lower passbands
21
PBT2 PBT2 PBT2
PBT1
PBT1 PBT1
Passband Passband
4-3
4 RECEIVING AND TRANSMITTING
DEPTH (Default: 8)
Adjust the noise attenuation depth between 1 and 10.
4-5
4 RECEIVING AND TRANSMITTING
NOTE:
••When you rotate MAIN DIAL while the Digital Selector
is ON, mechanical noise may be heard due to the
switching noise from internal relays.
••The P.AMP 1 or P.AMP 2 preamps cannot be used while
using the Digital Selector.
4-6
RECEIVING AND TRANSMITTING 4
OFF
ON
COMP zone
4. P
ush MULTI to display the Multi-function menu.
5. T ouch [MIC GAIN], and then adjust it by speaking
into the microphone (p. 3-9) to where the ALC
meter reads within the 30 to 50% range of the
ALC zone.
6. T
ouch the meter again to display the COMP
meter.
1. Select the AM mode or CW mode. NOTE: When receiving a weak signal, or receiving a signal
2. Push AUTO TUNE to start the Auto Tuning. with interference, the Auto Tuning function may tune the
LWhile using the RIT function, the RIT frequency is receiver to an undesired signal, or may not start tuning. In
automatically tuned by this function. such case, a warning beep sounds.
4-8
RECEIVING AND TRANSMITTING 4
4-9
4 RECEIVING AND TRANSMITTING
3. R
otate KEY
SPEED PITCH (outer) to adjust to between 300
to 900 Hz.
Displayed when the Dial Lock function is ON.
You can select the transmit filter width for the SSB
mode to WIDE (wide), MID (middle) or NAR (narrow).
Operating CW (Continued)
4-11
4 RECEIVING AND TRANSMITTING
Operating CW
DD Using the Break-in function (Continued) DDAPF (Audio Peak Filter) operation
The APF enables you to set excellent selectivity in the
Full Break-in mode CW mode. You can set the selectivity to between the
In the Full Break-in mode, the transceiver three APF passband width, WIDE, MID or NAR.
automatically transmits while keying down, and then
immediately returns to receive after keying up. 1. Select the CW mode.
2. Push APF/TPF to turn ON the Audio Peak Filter.
1. Select the CW mode.
2. Touch [BK-IN] in the function menu to select
APF/TPF
“FULL.”
LTouching [BK-IN] changes between “BKIN (Semi
Break-in),” “F-BKIN (Full Break-in)” and OFF (no
indication).
LLInformatio
••This enables you to match your transmit 4. T
ouch to select the item, and then set the audio
frequency exactly to another station’s by matching filter position, passband width, and the audio level.
the audio tone. POSITION: Rotate MULTI to shift the peak
••You can also use the CW side tone (be sure the frequency of the APF. This function
Break-in function is OFF) to practice CW sending.
enables you to avoid interference from
••You can adjust the CW side tone level in “Side Tone
adjacent frequencies.
Level.”
MENU » KEYER > EDIT/SET > CW-KEY SET > WIDTH: Touch to select WIDE, MID or NAR.
Side Tone Level TYPE: Select the audio filter type (soft sound
or sharp sound).
AF LEVEL: Set the audio level between 0 dB and
+6 dB in 1 dB steps.
5. To close the APF menu, push EXIT .
4-12
RECEIVING AND TRANSMITTING 4
Operating CW (Continued)
4-13
5 SCOPE OPERATION
5-1
SCOPE OPERATION 5
5-2
5 SCOPE OPERATION
5-3
SD CARD/USB FLASH DRIVE 6
SD card, SDHC card, and USB flash drive are not
supplied by Icom. They are user supplied.
Saving data
TIP: Icom recommends that you save the transceiver’s You can save the following data onto the card or USB
factory default data for backup. flash drive. 1
SD Card
••Data settings and Memory channel contents of the
2
About the SD cards transceiver
••Communication log and contents
3
You can use an SD card of up to 2 GB, or an SDHC of
up to 32 GB. Icom has checked the compatibility with
••Voice audio for the Voice TX function
••RTTY and PSK decode log
4
••Captured screens
the following SD and SDHC cards.
5
(As of September 2017) USB flash drive
Brand Type Memory size ••Data settings and Memory channel contents of the
transceiver
6
SD 2 GB
4 GB
••Captured screens
7
SanDisk® 8 GB
SDHC
16 GB 8
32 GB Inserting 9
LThe above list does not guarantee the card’s
performance.
LThroughout the rest of this document, the SD card
Insert the SD card or USB flash drive as shown below.
LInsert the SD card into the slot until it locks in place, and 10
and SDHC card are simply called the SD card or the makes a ‘click’ sound.
card. LBe sure to check the card or flash drive orientation before 11
inserting.
12
About the USB flash drive
13
Lights blue
Use the USB flash drive that supports the interface
1.1 or 2.0. 14
LThese do not guarantee the USB flash drive’s
performance.
SD Beveled corner
15
LO
CK
SD card 16
NOTE:
••Before using the SD card or USB flash drive, thoroughly
read the their instructions. USB flash drive
17
••If any of the following occur, the card data or flash drive
data may be corrupted or deleted.
••“USB” is displayed on the screen.
18
- You remove the card or flash drive from the transceiver
while they are being accessed. 19
- A power failure occurs or the power cable is NOTE:
disconnected while the they are being accessed.
- You drop, impact or vibrate the card or flash drive.
Before using an SD card or USB flash drive 20
with the transceiver for the first time, be sure to
••Do not touch the contacts of the card or flash drive.
••The transceiver takes a longer time to recognize a high
format all SD cards or USB flash drive (p. 6-2). 21
••Formatting a card or flash drive erases all its data.
capacity card or flash drive.
••Before formatting any used card or flash drive, back up
••The card or USB flash drive has a certain lifetime, so
its data onto your PC.
data reading or writing may not be possible after using it
••After inserting or formatting, a special folder on the card
for a long period of time.
or flash drive that you need for operations like updating
When reading or writing data is impossible, the card or
the firmware are created on the card or flash drive.
flash drive’s lifetime may have ended. In that case, use a
new one.
We recommend that you make a separate backup file of IMPORTANT: Even if you have formatted an SD
the important data onto your PC. card, some data may remain in the card. When you
••Icom will not be responsible for any damage caused by dispose the card, be sure to physically destroy it to
data corruption on a card or USB flash drive. avoid unauthorized access to any data that remains.
6-1
6 SD CARD/USB FLASH DRIVE
Formatting Unmounting
Before using an SD card with the transceiver, be Before you remove a card when the transceiver is ON,
sure to format all SD cards with the Format function. be sure to electrically unmount it, as shown below.
Format, even preformatted cards for PCs or other uses. Otherwise the data may be corrupted or deleted.
LAfter unmounting, SD card indicator turns OFF or “USB”
disappears from the screen.
DDFormatting the SD card or
1. O
pen the SD CARD or USB FLASH DRIVE
USB flash drive
screen.
1. O
pen the SD CARD or USB FLASH DRIVE MENU » SET > SD Card
screen. MENU » SET > USB Flash Drive
MENU » SET > SD Card
2. Touch “Unmount.” (Example: SD card)
MENU » SET > USB Flash Drive
2. Touch “Format.” (Example: SD card)
Turns OFF
Remove
q Push in
w Pull out
LTo cancel formatting, touch [NO].
••After formatting, returns to the SD CARD set screen. LPush in the SD card until a click sounds to
4. T
o close the SD CARD set screen, push EXIT unlock the card and to pull it out.
several times. 5. To close the SD CARD or USB FLASH DRIVE set
screen, push EXIT several times.
6-2
ANTENNA TUNER OPERATION 7
About the Antenna memory settings
This function saves antenna connector settings for DDSaving an antenna connector setting 1
each frequency band. You can set antenna connectors Example: Assigning ANT2 to the 10 MHz band.
ANT1, ANT2, ANT1/R, ANT2/R, ANT1 or ANT2
to selected bands. 1. Display the ANTENNA screen. 2
LANT1 is set to all frequency bands as the default. MENU » ANTENNA
3
DDThe Antenna memory screen 2. Select the 10 MHz band.
The Antenna memories are set on the ANTENNA 4
screen.
MENU » ANTENNA
5
Antenna selection mode
Antenna type setting
6
7
3. Touch [ANT] and select “2 (ANT2).” 8
“2 ” is displayed.
9
Displayed while a different antenna
from the original is temporarily
The Temporary function 10
memory ON or OFF.
selected. (Example: ANT 2)
7-1
7 ANTENNA TUNER OPERATION
About the Antenna memory settings (Continued) About the internal antenna tuner
DDSelecting the antenna type The internal automatic antenna tuner automatically
Select the antenna connecting options between matches the transceiver to the antenna within the
“Connect Receive Antenna” (RX-ANT is displayed as range of 16.7 ~ 150 Ω (SWR of less than 1:3).
the type) and “Connect External RX Device” (RX-I/O
is displayed as the type.) After the tuner matches an antenna, the latching relay
L“Connect Receive Antenna” is set as the default. combinations are memorized as a preset point for
each frequency range (100 kHz steps). Therefore,
1. Display the ANTENNA screen. when you change the frequency range, the latching
MENU » ANTENNA relay combinations are automatically preset to the
memorized point for fast tuning.
2. Touch [TYPE].
LWhen you install a new antenna, or you want to
change the antenna settings, you can clear the all
of the internal antenna tuner preset points with the
“<<Preset Memory Clear>>” item on the TUNER set
screen. (p. 8-3)
MENU » SET > Function > Tuner >
Antenna type
<<Preset Memory Clear>>
••The TYPE SET screen is displayed.
4. S
elect an option.
(Example: Connect External RX Device)
7-2
ANTENNA TUNER OPERATION 7
NOTE:
white.
LWhen the long wire antenna cannot be tuned, the
16
If the SWR is higher than about 1.5:1 when tuning more
than 100 kHz on an antenna’s preset point, hold down
indicator goes out. In that case, the AH-4 is bypassed
and the wire is directly connected. 17
TUNER for 1 second to start manual tuning.
NOTE: When the wire antenna cannot be tuned, check the
wire length and connection.
18
If the tuner cannot tune the antenna
••Repeat manual tuning several times.
Note that the AH-4 cannot tune a wire that is a ½λ long or
on a multiple of that frequency. 19
••Even if the tuner cannot tune the antenna on the first
tuning, it may success at the second tuning. 20
••Some antennas, especially for the low bands, have a
narrow bandwidth. These antennas may not tune at 21
the edge of their bandwidth, therefore, tune such an
antenna as follows:
(Example):
Suppose you have an antenna which has an SWR of 1.5:1
at 3.55 MHz and an SWR of 3:1 at 3.8 MHz.
1. Set 3.55 MHz, and hold down TUNER for 1
second to start manual tuning.
2. Set 3.80 MHz, and hold down TUNER for 1
second to start manual tuning.
7-3
7 ANTENNA TUNER OPERATION
DDUsing an external antenna tuner NOTE: Be sure not to connect the antenna tuner without
When you use a non-Icom external antenna tuner, an antenna connected. This could damage the transceiver
be sure to turn OFF the internal antenna tuner before or external antenna tuner.
connecting it.
Otherwise, the tuning may fail because both antenna TIP:
tuners (internal and external) will simultaneously start If the SWR is not reduced to 2:1 after retuning, see
tuning. “If the tuner cannot tune the antenna” on page 7-3
See the antenna tuner’s instruction manual for details. for details.
3. Touch [OK].
8-1
8 SET MODE
TX Bass (Default: 0)
MENU » SET > Tone Control > RX > SSB TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio.
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio high- TBW (WIDE) (Default: 100 – 2900)
pass filter and low-pass filter in 100 Hz steps, in the TBW (MID) (Default: 300 – 2700)
SSB mode. TBW (NAR) (Default: 500 – 2500)
LIf this item is set, the “RX Bass” and “RX Treble” Sets the transmission pass bandwidth to wide, mid,
items are automatically set to “0.” or narrow, by changing the lower and higher cut-off
frequencies.
RX Bass (Default: 0)
RX Treble (Default: 0) MENU » SET > Tone Control > TX > AM
Sets the bass or treble level of the receive audio.
TX Bass (Default: 0)
MENU » SET > Tone Control > RX > AM TX Treble (Default: 0)
Sets the bass or treble level of the transmit audio.
RX HPF/LPF (Default: – – – – – – – – –)
Sets the cut-off frequencies for the receive audio high- MENU » SET > Tone Control > TX > FM
pass filter or low-pass filter in 100 Hz steps, in the AM
mode. TX Bass (Default: 0)
Selectable ranges: TX Treble (Default: 0)
LIf this item is set, the “RX Bass” and “RX Treble” Sets the bass or treble level of the transmit audio.
items are automatically set to “0.”
RX Bass (Default: 0)
RX Treble (Default: 0)
Sets the bass or treble level of the receive audio.
Function
MENU » SET > Tone Control > RX > FM MENU » SET > Function
RX HPF/LPF (Default: – – – – – – – – –)
Beep Level (Default: 50%)
Sets the cut-off frequencies for the receive audio high-
Sets the beep output level.
pass filter or low-pass filter in 100 Hz steps, in the FM
LIf the “Beep (Confirmation)” item is set to “OFF,” no
mode.
beeps sound.
LIf this item is set, the “RX Bass” and “RX Treble”
items are automatically set to “0.” Beep Level Limit (Default: ON)
FM RX Bass (Default: 0) Selects whether or not to limit the volume up to the
FM RX Treble (Default: 0) specified level.
Sets the bass or treble level of the receive audio. Beep (Confirmation) (Default: ON)
Turns the Confirmation beep ON or OFF.
MENU » SET > Tone Control > RX > CW
LIf the “Beep Level” item is set to “0%,” no beep sounds.
MENU » SET > Tone Control > RX > RTTY
MENU » SET > Tone Control > RX > PSK Band Edge Beep (Default: ON (Default))
Turns the Band Edge beep ON or OFF.
RX HPF/LPF (Default: – – – – – – – – –)
LLInformatio
Sets the cut-off frequencies for the receive audio high- ••If the “Beep Level” item is set to “0%,” no beep sounds.
pass filter or low-pass filter in 100 Hz steps in the CW, ••When you tune into an amateur band’s frequency
RTTY, and PSK modes. range, the high Band Edge beep sounds.
••When you tune out of an amateur band’s frequency
range, the low Band Edge beep sounds.
8-2
SET MODE 8
Beep Sound (MAIN) (Default: 1000Hz) MENU » SET > Function > Tuner
Beep Sound (SUB) (Default: 1000Hz)
Set the audio frequency for beeps. PTT Start (Default: OFF)
8-3
8 SET MODE
Memo Pad Quantity (Default: 5) Screen Full Keyboard Layout (Default: English)
Sets the number of memo pad channels. Select the on-screen keyboard layout between
English, German and French.
MAIN DIAL Auto TS (Default: High)
Sets the Auto Tuning Step function for MAIN DIAL . Screen Capture [POWER] Switch (Default: OFF)
When rapidly rotating MAIN DIAL , the tuning step Assigns the Screen Capture function to POWER .
automatically changes according to the rotation speed.
Screen Capture Keyboard [Print Screen]
MAIN/SUB DIAL Select (USB DIAL–SUB Only) (Default: OFF)
(Default: MAIN/SUB)
Assigns the Screen Capture function to the [Print
Selects whether MAIN DIAL changes only the Main Screen] key on the USB keyboard.
band frequency, or changes both the Main and Sub
band frequencies, depending on which band is Screen Capture Storage Media (Default: SD Card)
selected.
Selects the SD card or USB flash drive to save screen
LThis is convenient when using the optional RC-28 remote capture data.
encoder to change the Sub band frequency.
8-4
SET MODE 8
MENU » SET > Connectors > Phones AF SQL (Default: OFF (Open)) 1
Selects whether or not to output the audio from [USB],
Level (Default: 0)
Sets the audio output level ratio of the headphone and
according to the squelch state. 2
internal speaker between -15 and +15. AF Beep/Speech... Output (Default: OFF)
3
Sets the Beep and Speech audio output setting of
L/R Mix (Default: OFF)
Selects to output the mixed audio from the headphones
[ACC].
LYou should set the “AF SQL” item to “AF.”
4
or to output the Main band’s audio from the leftside and
the Sub band’s audio from the rightside.
LThe beep level is limited when the “Beep Level
Limit” item is “ON.”
5
MENU » SET > Connectors > ACC AF/IF Output IF Output Level (Default: 50%) 6
AF/SQL Output Select (Default: MAIN)
Sets the IF output level of [USB].
7
Selects the audio and squelch signals to output from
[ACC1] (Audio: pin 5, Squelch: pin 6) in the Main and
MENU » SET > Connectors > LAN AF/IF Output
8
Sub bands. Output Select (Default: AF)
Selects the signal output type from [LAN].
9
Output Select (Default: AF)
Selects AF signal or IF signal to output from [ACC]. AF SQL (Default: ON) 10
AF/IF XFC Output (SPLIT ON) (Default: SUB)
Selects the squelch behavior of [LAN].
11
Selects the signal output from [ACC1] while XFC is » SET > Connectors > MOD Input
held down in split operation.
MENU
12
ACC MOD Level (Default: 50%)
AF Output Level (Default: 50%)
Sets the modulation input level of [ACC].
13
Sets the AF output level of [ACC].
USB MOD Level (Default: 50%) 14
AF SQL (Default: OFF (Open))
Selects whether or not to output the audio from [ACC],
Sets the modulation input level of [USB].
15
according to the squelch state. LAN MOD Level (Default: 50%)
Sets the modulation input level of [LAN].
16
AF Beep/Speech... Output (Default: OFF)
Sets the Beep and Speech audio output setting of DATA OFF MOD (Default: MIC,ACC) 17
[ACC]. Selects the connector(s) to input the modulation signal
LYou should set the “AF SQL” item to “AF.” when the data mode is OFF. 18
LThe beep level is limited when the “Beep Level Limit”
item is “ON.” 19
ACC IF Output Level (Default: 50%) 20
Sets the IF output level of [ACC].
21
MENU » SET > Connectors > USB AF/IF Output
8-5
8 SET MODE
MENU » SET > Connectors > External Keypad USB DIAL [TRANSMIT] Switch
(Default: Push to toggle)
VOICE (Default: OFF) Selects whether to toggle between transmit and
Enables voice memory transmission using an external receive by pushing, or to transmit only while holding
keypad. the [TRANSMIT] key on the RC-28.
8-6
SET MODE 8
MENU » SET > Connectors > CI-V External Meter Level (MAIN) (Default: 50%)
External Meter Level (SUB) (Default: 50%)
CI-V Baud Rate (Default: Auto) Sets the output level to the external meter (Main and
Selects the CI-V data transfer rate. Sub band). 1
LWhen “Auto” is selected, the baud rate is
automatically set according to the data rate of the
connected device.
MENU » SET > Connectors 2
CI-V Address (Default: 98)
Decode Baud Rate (Default: 9600)
Selects the data transfer rate (Baud rate) of decoded
3
Sets the CI-V address.
L“98h” is the default address of the IC-7610.
signals.
4
SEND Relay Type (Default: MOS-FET)
CI-V Transceive (Default: ON) Selects the switching relay type for [RELAY].
5
Turns the Transceive function ON or OFF. Select the suitable relay type, especially when
connecting a non-Icom linear amplifier.
6
CI-V USB/LAN→REMOTE Transceive Address
(Default: 00) ACC BAND Voltage Output (Default: TX) 7
Sets the address used to remotely control the
transceiver or receiver using the optional RS-BA1,
Selects the operating band voltage output from
[ACC2] (pin 4).
8
through the [USB] port.
The external equipment control signal is output from MIC Input DC Bias (Default: ON) 9
the [REMOTE] port. Outputs the 8 V bias voltage (approximate) from the
microphone connector (pin 1 of [MIC]). 10
CI-V Output (for ANT) (Default: OFF)
Enables outputting the antenna controller status REF IN (Default: OFF) 11
(frequency and so on) from the [REMOTE] port. Selects the transceiver’s reference frequency signal
LAddress “01h” is reserved. source. 12
The usable addresses are limited to 02h ~ DFh. LThis setting will be valid after restarting the transceiver.
LIf the applied reference signal is off frequency, or not high 13
CI-V USB Port (Default: Unlink from [REMOTE]) enough, the IC-7610 will not work correctly. In that case,
Selects the internal connection type between the select “OFF,” and then restart the IC-7610. 14
[USB] and [REMOTE] CI-V ports.
15
CI-V USB Baud Rate (Default: Auto)
Selects the CI-V data transfer rate when remotely 16
controlling the IC-7610 through the [USB] CI-V port. Network
LWhen “Auto” is selected, the baud rate is 17
automatically set according to the data rate of
MENU » SET > Network
external device. 18
LThis setting is valid only when the “CI-V USB Port”
DHCP (Default: ON( . . . ))
item is set to “Unlink from [REMOTE].”
Turns the DHCP function ON or OFF. 19
CI-V USB Echo Back (Default: OFF)
Turns the Data Echo Back function ON or OFF, when
IP Address (Default: 192.168. 0. 10) 20
Sets the static IP address.
remotely controlling the IC-7610 through the [USB]
CI-V port.
21
LThis setting is valid only when the “CI-V USB Port” Subnet Mask (Default: 255.255.255. 0 (24 bit))
item is set to “Unlink from [REMOTE].” Sets the subnet mask to connect to your PC or LAN
(Local Area Network), through the Ethernet.
MENU » SET > Connectors > External Meter
Default Gateway (Default: —)
External Meter Output (MAIN) (Default: Auto)
lf you are operating the IC-7610 using the optional
External Meter Output (SUB) (Default: Auto)
RS-BA1, a default gateway setting is required.
Selects the parameter (Main and Sub readout) to
output to an external meter.
8-7
8 SET MODE
Audio Port (UDP) (Default: 50003) Meter Response (Standard, Edgewise)(Default: Mid)
lf you are operating the IC-7610 using the optional Sets the meter needle response speed to Slow, Mid or
RS-BA1 software, set a port number for the audio Fast.
signal between the IC-7610 and the remote station.
Meter Type (Normal Screen) (Default: Standard)
Internet Access Line (Default: FTTH) Sets the S/RF meter type for the normal display to
lf you are operating the IC-7610 using the optional Standard, Edgewise or Bar.
RS-BA1 software, set the port number for the audio
signal between the IC-7610 and the remote station. Meter Type (Expand Screen) (Default: Bar)
Sets the S/RF meter type for the expanded display to
MENU » SET > Network > Network User1 Standard, Edgewise or Bar.
MENU » SET > Network > Network User2 Meter Peak Hold (Bar) (Default: ON)
Network User1 ID (Default: —) Turns the Meter Peak Hold function ON or OFF.
Network User2 ID (Default: —)
lf you are operating the IC-7610 using the optional Memory Name (Default: ON)
RS-BA1, enter a user name of up to 16 characters. Turns the Memory name display in the Memory mode
ON or OFF.
Network User1 Password (Default: —)
Network User2 Password (Default: —) APF-Width Popup (APF OFF→ON) (Default: ON)
Enter a password for each user. Turns the APF filter width display ON or OFF.
8-8
SET MODE 8
8-9
8 SET MODE
Partial Reset
USB Flash Drive Resets operating settings to their default values (VFO
frequency, VFO settings, menu contents) without
MENU » SET > USB Flash Drive clearing the items below:
••Memory channel contents
Load Setting ••MY Call
Selects the saved data file to load. ••Memory Keyer
••RTTY memory
Save Setting ••User Band Edge
••REF Adjust
Saves the setting data onto a USB flash drive.
••Fixed Edges
USB Flash Drive Info LSee “Resetting” (p.10-1) for details.
Displays the USB flash drive capacity and the time All Reset
remaining for voice recording.
Clears all data and returns all settings to their factory
Screen Capture View defaults.
Memory channel contents, filter setting and so on
Displays the selected screen capture. will all be cleared, so you will need to rewrite your
operating settings.
Firmware Update
LSee “Resetting” (p. 10-1) for details.
Displays the Firmware Update mode.
MENU » SET > Others > Emergency
Format
Formats the USB flash drive. Emergency
If you use a brand new USB flash drive, be sure to Enters the Emergency mode by touching “Tuner.”
format it in the transceiver. LSee page 7-4 for details.
Unmount
Unmounts the USB flash drive.
Before you remove a flash drive when the transceiver
is ON, be sure to electrically unmount it. Otherwise
the data may be corrupted or deleted.
8-10
CLOCK AND TIMERS 9
Setting the date and time
9-1
9 CLOCK AND TIMERS
1. Display the TIME SET screen. 1. Display the TIME SET screen.
MENU » SET > Time Set » SET > Time Set
MENU
9-2
MAINTENANCE 10
Resetting
Occasionally, erroneous information may be DDPartial reset 1
displayed. This may be caused by static electricity or 1. Open the RESET screen.
by other factors.
If this problem occurs, turn OFF the transceiver. After
MENU » SET > Others > Reset
2
waiting a few seconds, turn ON the transceiver again. 2. Touch “Partial Reset.”
If the problem still exists, perform a Partial reset, as 3
described to the right.
If the problem still exists after a Partial reset, perform 4
an All reset, as described to the right.
5
NOTE: An All reset clears all data and returns all settings ••The confirmation screen is displayed.
to their factory defaults. Save memory channel content,
setting status, and so on, onto an SD card before an All
6
3. Touch [Yes].
reset. (p. 10-1) L After the resetting, the default VFO mode screen is
displayed.
7
8
After performing a Partial reset
A Partial reset resets operating settings to their default 9
values (VFO frequency, VFO settings, menu contents)
without clearing the items listed below: 10
••Memory channel contents
••Fixed Edges on the Spectrum Scope 11
••Network settings in the set mode
DDAll reset
••MY Call
••REF Adjust 1. Open the RESET screen.
12
MENU » SET > Others > Reset
13
2. Touch “All Reset.”
After performing an All reset
All reset clears all data and returns all settings to their
14
factory defaults.
Memory channel contents, filter setting and so on
15
will all be cleared, so you will need to rewrite your
operating settings, unless you have a backup.
16
••The confirmation screen is displayed. 17
When you cannot enter the Set mode 3. Touch [NEXT].
If a touch screen operation error or an unexpected
18
operation occurs, you cannot enter the Set mode. In
this case, perform an All reset, as described below:
19
While holding down MAIN/SUB and CHANGE , 20
push POWER .
21
4. A
fter carefully reading the displayed message,
touch [YES] to perform the All reset.
LAfter the resetting, the default VFO mode screen is
displayed.
10-1
10 MAINTENANCE
Troubleshooting
The following chart is designed to help you solve problems that are not equipment malfunctions.
If you are unable to locate the cause of a problem, or solve it through the use of this chart, contact your nearest
Icom Dealer or Service Center.
The external power supply is turned OFF. Turn ON the external power supply. p. 2-1
The DC power cable fuses or circuitry Find and repair the cause of the problem, –
fuse are blown. and then replace the damaged fuse with
a new one.
No sound is heard from The audio level is too low. Rotate AF RF/SQL (inner) clockwise to p. 3-1
the speaker. obtain a suitable listening level.
The squelch is closed. Rotate AF RF/SQL (outer) to the 12 p. 3-7
o’clock position to open the squelch.
If no sound is heard only from the Sub Turn ON the Dualwatch function. p. 3-2
band, the Dualwatch function is OFF.
Headphones are connected. Disconnect the headphones. p. 13-1
The Mute function is ON. Push AF RF/SQL to turn OFF the Mute p. 1-1
function on whichever band is selected
(Main or Sub).
The external speaker cable is defective. Check the external speaker cable and –
repair it.
Sensitivity is too low, and The attenuator is activated. Turn OFF the attenuator in the p. 4-1
only strong signals are Multi-function key group.
heard. The squelch is closed. p. 3-7
Rotate AF RF/SQL (outer) to 12 o’clock
position to open the squelch.
The antenna is defective or the coaxial Repair the problem and then reconnect p. 2-2
cable is defective. the antenna.
You are using an antenna that is not Connect an antenna suitable for the p. 2-2
suitable for the band you have selected. operating frequency.
Hold down TUNER to tune the antenna. p. 7-2
No power output or the The operating frequency is outside the Set the frequency to a ham band. p. 3-4
output power is too low. ham band.
The modulation input signal level is set Adjust the microphone gain in MIC GAIN. p. 3-9
too low.
The microphone is bad, or the [MIC] Test the microphone and check the [MIC] p. 13-3
connector is shorted or defective. connector.
The antenna SWR is more than 3:1. Adjust the antenna for an SWR of less p. 7-3
than 3:1.
The antenna is not properly tuned. Hold down TUNER for 1 second to tune p. 7-3
the antenna.
The transmit output power is set too low. Adjust the RF POWER in the Multi- p. 3-8
function menu.
10-2
MAINTENANCE 10
Troubleshooting (Continued)
The coaxial cable is not suitable. Use a coaxial cable whose characteristic p. 12-1 18
impedance is 50 Ω.
19
“OVF” is displayed. An excessively strong signal is received. Rotate AF RF/SQL (outer) counter p. 3-7
clockwise. 20
Turn ON the attenuator. p. 4-1
Turn OFF the Preamplifier (P.AMP OFF). p. 4-1 21
Turn ON the Digital Selector function. p. 4-6
The touch screen is not The touched point and the detected point Calibrate the touch screen in the p. 8-10
working correctly. may be different. OTHERS screen.
10-3
11 SPECIFICATIONS
DDGeneral
••Frequency coverage (unit: MHz):
Receiver 0.030000 ~ 60.000000
Transmitter 0.135700 ~ 0.137800 (Only in the European version)
1.800000 ~ 01.999999*
3.500000 ~ 03.999999*
5.255000 ~ 05.405000 (Only in the USA version)
7.000000 ~ 07.300000*
10.100000 ~ 10.150000
14.000000 ~ 14.350000
18.068000 ~ 18.168000
21.000000 ~ 21.450000
24.890000 ~ 24.990000
28.000000 ~ 29.700000
50.000000 ~ 54.000000*
*The frequency coverage and guaranteed ranges differ, depending on the
transceiver version.
••Operating modes: USB/LSB (J3E), CW (A1A), RTTY (F1B), PSK (G1B),
AM (A3E) and FM (F3E)
••Number of memory channels: 101 (including 2 scan edges)
••Antenna connectors: SO-239×2 (antenna impedance: 50 Ω Unbalanced)
••Power supply requirement: 13.8 V DC (±15%)
••Operating temperature range: 0°C to +50°C, +32°F to +122°F
••Frequency stability: Less than ±0.5 ppm (0°C to +50°C, +32°F to +122°F)
••Frequency resolution: 1 Hz (minimum)
••Power consumption:
Receive Standby 3.0 A
Maximum audio 3.5 A
Transmit Maximum power 23.0 A
••Dimensions (projections not included): 340 (W) × 118 (H) × 277 (D) mm, 13.4 (W) × 4.6 (H) × 10.9 (D) in
••Weight (approximate): 8.5 kg, 18.7 Ib
DDTransmitter
••Transmit output power:
HF and 50 MHz bands
SSB/CW/RTTY/PSK/FM 1~100 W
AM 1~25 W
••Modulation system:
SSB P.S.N. modulation
AM Low power modulation
FM Reactance modulation
••Spurious emission:
Harmonics Less than –50 dB (HF band)
Less than –63 dB (50 MHz band)
Out-of-band emission Less than –40 dB (HF band)
Less than –60 dB (50 MHz band)
••Carrier suppression: More than 50 dB
••Unwanted sideband suppression: More than 50 dB
••Microphone impedance: 600 Ω
11-1
SPECIFICATIONS 11
DDReceiver
••Receive system: Direct sampling superheterodyne
••Intermediate frequency: 12 kHz
••Sensitivity (Filter: SOFT):
SSB/CW (at 10 dB S/N)
1
1.8 ~ 29.999999 MHz
50 MHz band
–16 dBm (0.16 μV) typical
–18 dBm (0.13 μV) typical
(P.AMP1 ON)
(P.AMP2 ON)
2
AM (at 10 dB S/N)
0.1 ~ 1.799999 MHz +16 dBm (6.3 μV) typical (P.AMP1 ON) 3
1.8 ~ 29.999999 MHz +6 dBm (2.0 μV) typical (P.AMP1 ON)
50 MHz band 0 dBm (1.0 μV) typical (P.AMP2 ON) 4
FM (at 12 dB SINAD)
28.0 ~ 29.7 MHz –6 dBm (0.5 μV) typical (P.AMP1 ON) 5
50 MHz band –10 dBm (0.32 μV) typical (P.AMP2 ON)
••Sensitivity for the European version (Filter: SOFT): 6
SSB (BW=2.4 kHz, 12 dB SINAD)
1.8 ~ 2.999999 MHz Less than 10 dBμV emf (P.AMP 1 ON) 7
3.0 ~ 29.999999 MHz Less than 0 dBμV emf (P.AMP 1 ON)
50 MHz band Less than –6 dBμV emf (P.AMP 2 ON) 8
AM (BW=4 kHz, 60% Modulation, 12 dB SINAD)
1.8 ~ 2.999999 MHz Less than 16 dBμV emf (P.AMP 1 ON) 9
3.0 ~ 29.999999 MHz Less than 6 dBμV emf (P.AMP 1 ON)
50 MHz band Less than 0 dBμV emf
FM (BW=7 kHz, 60% Modulation, 12 dB SINAD)
(P.AMP 2 ON) 10
28.0 ~ 29.7 MHz
50 MHz band
Less than 0 dBμV emf
Less than –6 dBμV emf
(P.AMP 1 ON)
(P.AMP 2 ON)
11
••Squelch sensitivity (threshold):
SSB Less than +10 dBm (3.2 μV)
12
FM Less than –10 dBm (0.32 μV)
(HF band: P.AMP1 ON, 50 MHz band: P.AMP2 ON)
13
••Selectivity (Filter: SHARP):
SSB (BW=2.4 kHz) More than 2.4 kHz/–6 dB 14
Less than 3.6 kHz/–60 dB
CW (BW=500 Hz) More than 500 Hz/–6 dB 15
Less than 700 Hz/–60 dB
RTTY (BW=500 Hz) More than 500 Hz/–6 dB 16
Less than 700 Hz/–60 dB
AM (BW=6 kHz) More than 6.0 kHz/–6 dB 17
Less than 15 kHz/–60 dB
FM (BW=15 kHz) More than 12.0 kHz/–6 dB 18
Less than 20 kHz/–60 dB
••Spurious and image rejection: More than 70 dB (except for ADC aliasing) 19
••Audio output power: More than 2.0 W (8 Ω load, 1 kHz, 10% distortion)
••AF output impedance:
••RIT variable range:
8Ω
±9.999 kHz
20
21
DDAntenna tuner
••Tunable impedance range: 16.7~150 Ω (unbalanced) (less than 1:3 VSWR)
••Tuning accuracy: Less than 1:1.5 VSWR
••Tuning time (approximate): 2~3 seconds (average)
15 seconds (maximum)
LAll stated specifications are typical and subject to change without notice or obligation.
11-2
12 OPTIONS
Options
AH-740 automatic HM-219 microphone PS-126 dc power SupplY RC-28 remote encoder
tuning antenna For operating the
• Output voltage: 13.8 V DC
High performance, • Maximum output current: RS-BA1 (version 1.3
automatic high-speed 25 A or later) or using as a
tuning antenna. sub dial to operate the
transceiver.
Dynamic microphone with Desktop microphone External speaker with high External speaker with high
[UP]/[DOWN] switches. with a low frequency cut and low frequency cut and low frequency cut
function. functions. (2 W/8 Ω) functions. (3 W/8 Ω)
12-1
CONNECTOR INFORMATION 13
Interface information
1
PHONES (p. 13-3)
••6.35 mm (¼ in) (d)
2
3
ELEC-KEY (p. 13-3)
••6.35 mm (¼ in) (d) 4
USB ports (p. 13-4) 5
••A type
6
MIC (p. 13-3)
7
8
EXT KEYPAD (p. 13-4) ALC (p. 13-4) SEND (p. 13-4) 9
••3.5 mm (⅛ in) (d) ••RCA plug ••RCA plug
10
TUNER (p. 13-3)
METER (p. 13-4)
11
ACC 2 (p. 13-2) ANT 1 (p. 13-6)
••3.5 mm (⅛ in) (d) ••7-pin ••50 Ω
12
DC 13.8 V (p. 13-3) ANT 2 (p. 13-6)
REMOTE (p. 13-4)
••3.5 mm (⅛ in) (d)
••50 Ω 13
RX-ANT OUT (p. 13-6) 14
••BNC connector: 50 Ω
15
RX-ANT IN (p. 13-6)
••BNC connector: 50 Ω 16
17
REF IN (p. 13-5)
••BNC connector: 50 Ω
18
X-VERTER (p. 13-6) 19
••BNC connector: 50 Ω
KEY (p. 13-3)
••6.35 mm (¼ in) (d)
USB 1 port (p. 13-5)
••B type
20
21
LAN (p. 13-5)
ACC 1 (p. 13-2)
••8-pin
EXT-DISPLAY (p. 13-5)
••DVI-V (29 pin)
13-1
13 CONNECTOR INFORMATION
ACC sockets
Connects to external equipment or a PC to control an external unit or the transceiver.
••ACC sockets
PIN
ACC 1 NAME DESCRIPTION SPECIFICATIONS
No.
High level: More than 2.4 V
1 RTTY Controls RTTY keying. Low level: Less than 0.6 V
Output current: Less than 2 mA
2 GND Connects to ground. Connected in parallel with ACC 2 pin 2.
An external unit controls
Input/output the transceiver. Input voltage (RX): 2.0 ~ 20.0 V
pin. When this pin goes to Input voltage (TX): –0.5 ~ +0.8 V
3 SEND*1 Connected in ground, the transceiver Current flow: Maximum 20 mA
8-pin parallel with transmits.
ACC 2 pin 3. The pin goes low when Output voltage (TX): Less than 0.1 V
2 the transceiver transmits. Current flow: Maximum 200 mA
4 5
Modulator input. Input impedance: 10 kΩ
1 8 3 4 MOD
Connects to the internal modulator circuit. Output level: Approx. 100 mV rms*2
6 7
AF/IF Fixed AF detector or receive IF (12 kHz) Output impedance: 4.7 kΩ
5
(IF=12 kHz)*3 signal output. Output level: 100 ~ 300 mV rms*4
Rear panel view Squelch output. SQL open: Less than 0.3 V/5 mA
6 SQL S
Grounded when the squelch opens. SQL closed: More than 6.0 V/100 μA
13.8 V output when power is ON.
7 13.8 V Output current: Maximum 1A
Connected in parallel with ACC 2 pin 7.
ALC voltage input. Input level: –4 ~ 0 V
8 ALC
Connected in parallel with ACC 2 pin 5. Input impedance: More than 10 kΩ
PIN
ACC 2 NAME DESCRIPTION SPECIFICATIONS
No.
Output voltage: 8 V ±0.3 V
1 8V Regulated 8 V output.
Output current: Less than 10 mA
7-pin
2 GND Connects to ground (Same as ACC 1 pin 2).
2 3 SEND*1 Same as ACC 1 pin 3.
4 5
Band voltage output.
1 3 4 BAND Output voltage: 0 ~ 8.0 V
(Varies with the selected amateur band)
6 7
5 ALC Same as ACC 1 pin 8.
Activates [X-VERTER] input/output when Input impedance: More than 10 kΩ
6 TRV
Rear panel view “HIGH” voltage is applied. Input voltage: 2 ~ 13.8 V
7 13.8 V Same as ACC 1 pin 7.
*1 When
the SEND terminal controls an inductive load, such *2 You
can change the MOD input level.
as a relay, a counter-electromotive force can malfunction L100 mV rms is at 50% as the default.
or damage the transceiver. To prevent this, we recommend MENU » SET > Connectors > ACC MOD Level
adding a switching diode, such as an 1SS133, on the load
*3 You
can change the AF/IF (IF=12 kHz) settings to output a
side of the circuit to absorb the counter-electromotive force.
12 kHz IF signal. In that case, you can listen to the DRM
When the diode is added, a delay in relay switching may
broadcast with the application software receiver that is
occur. Be sure to check its switching action before operating.
installed onto your PC.
(Example) ACC 1/2 socket MENU » SET > Connectors > ACC Output Select
To a non-Icom MENU » SET > Connectors > USB Output Select
linear amplifier
e SEND MENU » SET > Connectors > LAN Output Select
*4 You
can change the AF/IF (IF=12 kHz) output level.
u 13.8 V
LApproximately 200 mV rms is at the 50% as the
Relay
default.
Switching diode
MENU » SET > Connectors > ACC IF Output Level
MENU » SET > Connectors > USB IF Output Level
13-2
CONNECTOR INFORMATION 13
PHONES MIC
Connects to standard stereo headphones: i AF output
••Output impedance: 8 ~ 16 Ω u GND 1
q Microphone input (Microphone ground)
••Output level: More than 5 mW into an 8 Ω load.
Sub band signal w +8 V DC output y GND (PTT ground)
2
e Frequency up/down
t PTT 3
6.35 (d) mm (¼ in)
Main band signal
r Squelch line output 4
NOTE: Pin 1 outputs 8 V DOC power for Icom 5
microphones.
ELEC-KEY LYou can turn OFF the DC power when you use non-Icom 6
microphones in the “MIC Input DC Bias” item on the
AH-4 (option)
13-3
13 CONNECTOR INFORMATION
Mute switch: Mutes both transmission and By connecting a PC keyboard to [USB], you can
reception when the switch is turned ON. output memory contents such as that from a CW
External Keypad Memory keyer (M1 ~ M8), Voice memory (T1 ~ T8),
RTTY Memory (RT1 ~ RT8), PSK memory (PT1 ~
PT8) to be transmitted.
1.5 kΩ 1.5 kΩ
±5% ±5% LTo use this function, set the following items to ON.
S5 S1
1.5 kΩ 1.5 kΩ MENU » SET > Connectors >
S6 ±5% S2 ±5%
Keyboard [F1]-[F8] (VOICE)
2.2 kΩ 2.2 kΩ
S7 ±5% S3 ±5% MENU » SET > Connectors >
4.7 kΩ 4.7 kΩ Keyboard [F1]-[F8] (KEYER)
±5% ±5%
S8 S4
REMOTE ALC
Connects to a PC for I/O Input ALC voltage to the jack when ALC
remote control using CI-V operating with a non-Icom linear
commands. amplifier.
••ALC voltage: –4 ~ 0 V GND
3.5 mm (⅛ in) (d)
GND
METER SEND
Connects to an external This terminal is used to control an SEND
meter. external equipment such as a non-Icom
+ _
Outputs the received signal + _ linear amplifier.
strength or squelch level. Main band Sub band The terminal goes low when the GND
meter meter
3.5 mm (⅛ in) (d) transceiver transmits. (RCA Plug)
••Output voltage: 8 V (maximum) LThe T/R switching relay type can be changed on the
••Output impedance: 10 kΩ following screen.
LYou can select the output signal from received MENU » SET > Connectors > SEND Relay Type
signal strength and squelch levels.
MENU » SET > Connectors
13-4
CONNECTOR INFORMATION 13
LAN USB 1
••Time synchronization by an NTP server. USB (1.1/2.0) type B
••Outputs the demodulated signal or 12 kHz IF signal. Connect to the PC when: 1
LYou can select the output signal from AF and IF ••Outputting the decoded FSK (RTTY) data.
signals. ••Outputting the demodulated AF signal or 2
» SET > Connectors > LAN AF/IF Output 12 kHz IF signal.
MENU
••Interface for the remote control by the 3
About the LED indication CI-V command.
q LINK/ACT LYou can change the signal output type and output 4
••Lights when a cable is connected. level.
••Does not light when a cable is not w q MENU » SET > Connectors > USB Output Select
5
connected.
••Blinks while communicating. MENU » SET > Connectors > USB AF Output Level 6
MENU » SET > Connectors > USB IF Output Level
w Speed
••Lights while communicating in 100BASE-TX.
7
LYou can download the USB driver and installation
••Does not light while communicating.
••Blinks while communicating in 10BASE-T, or not
guide from the Icom website. 8
h
ttp://www.icom.co.jp/world/support/download/firm/
connected.
index.html 9
10
EXT-DISPLAY EXT-SP A / EXT-SP B
11
Connects to external speakers.
Connects to an external display
monitor.
3.5 mm, ⅛ in (d) 12
Outputs the digital RGB signal. ••Output impedance: 4 ~ 8 Ω
(DVI-D)
••Output level: More than 2.0 W at 10% 13
distortion into an 8 Ω load.
LSet the external display settings on the following
screen.
14
LL Informatio
MENU » SET > Display > External Display
••The internal speaker is deactivated while an 15
external speaker is connected.
••[EXT-SP A] is for the Main band and [EXT-SP B] is 16
for the Sub band.
USB 2 17
USB (1.1/2.0/3.0) type B REF IN 18
This USB port is for digital data input or
output. Inputs a 10 MHz signal as a reference frequency
19
signal.
LThe required USB driver and driver’s installation 20
guide can be downloaded from Icom web site.
••Input frequency: 10 MHz
••Impedance: 50 Ω (unbalanced) 21
••Input level: –10 dBm (approximate)
LSelect the transceiver’s reference signal source.
MENU » SET > Connectors > REF IN
LAdjust the internal reference frequency.
MENU » SET > Function > REF Adjust
13-5
13 CONNECTOR INFORMATION
RX
MAIN receiver
SUB receiver
13-6
INSTALLATION NOTES
For amateur base station installations it is recommended In all cases any possible risk depends on the transmitter
that the forward clearance in front of the antenna array is being activated for long periods. (actual recommendation
calculated relative to the EIRP (Effective Isotropic Radiated limits are specified as an average during 6 minutes)
Power). The clearance height below the antenna array can Normally the transmitter is not active for long periods of
be determined in most cases from the RF power at the time. Some radio licenses will require that a timer circuit 1
antenna input terminals. automatically cuts the transmitter after 1–2 minutes etc.
As different exposure limits have been recommended for Similarly some types of emission, i.e., SSB, CW, AM etc.
2
different frequencies, a relative table shows a guideline for
installation considerations.
have a lower ‘average’ output power and the assessed risk
is even lower. 3
Below 30 MHz, the recommended limits are specified in 4
terms of V/m or A/m fields as they are likely to fall within the ••List of Country codes (ISO 3166-1)
near-field region. Similarly, the antennas may be physically
short in terms of electrical length and that the installation will Country Codes Country Codes
5
6
require some antenna matching device which can create 1 Austria AT 18 Liechtenstein LI
local, high intensity magnetic fields. Analysis of such MF 2 Belgium BE 19 Lithuania LT
installations is best considered in association with published 3 Bulgaria BG 20 Luxembourg LU
guidance notes such as the FCC OET Bulletin 65 Edition 4 Croatia HR 21 Malta MT 7
97-01 and its annexes relative to amateur transmitter 5 Czech Republic CZ 22 Netherlands NL
installations. The EC recommended limits are almost
identical to the FCC specified ‘uncontrolled’ limits and tables
6 Cyprus CY 23 Norway NO 8
7 Denmark DK 24 Poland PL
exist that show pre-calculated safe distances for different
antenna types for different frequency bands. Further
8 Estonia EE 25 Portugal PT 9
9 Finland FI 26 Romania RO
information can be found at http://www.arrl.org/.
10
11
France
Germany
FR
DE
27 Slovakia
28 Slovenia
SK
SI
10
••Typical amateur radio installation
Exposure distance assumes that the predominant radiation 12
13
Greece
Hungary
GR 29 Spain
HU 30 Sweden
ES
SE
11
pattern is forward and that radiation vertically downwards
is at unity gain (sidelobe suppression is equal to main lobe
gain). This is true of almost every gain antenna today.
14
15
Iceland
Ireland
IS
IE
31 Switzerland
32 Turkey
CH
TR 12
Exposed persons are assumed to be beneath the antenna 16 Italy IT 33 United Kingdom GB
array and have a typical height of 1.8 m. 17 Latvia LV 13
The figures assume the worst case emission of a constant 14
carrier.
I
INDEX
Panel
P Tuner
Emergency mode ........................................................... 7-4
13
PTT Tuner start............................................................... 7-3
14
Front ............................................................................... 1-1
Rear ............................................................................... 1-3
Touch screen .................................................................. 1-4 Tuning
Pitch control, CW ................................................................. 4-10
Position, APF ....................................................................... 4-12
1/4 Tuning function .........................................................
Auto ................................................................................
3-5
4-8
15
Power
Applying ......................................................................... 3-1
Manual ...........................................................................
Step function, Setting .....................................................
7-3
3-4 16
ON or OFF ...................................................................... 3-1 Twin PBT, Using .................................................................... 4-3
Preamplifiers ......................................................................... 4-1 17
U
Q
QUICK MENU ........................................................................ 1-7
USB flash drive ...................................................................... 6-1
Formatting ...................................................................... 6-2
18
Quick Split ............................................................................. 4-9 Inserting ......................................................................... 6-1
Saving data .................................................................... 6-1 19
R Set mode ...................................................................... 8-10
Resetting
All ................................................................................. 10-1
Unmounting .................................................................... 6-2
UTC offset
20
Partial ........................................................................... 10-1 CLOCK2 ......................................................................... 9-2
RF gain .................................................................................. 3-7 Setting ............................................................................ 9-1 21
RIT
Function ......................................................................... 4-1 V
Monitor function .............................................................. 4-1 VFO mode, Selecting ............................................................ 3-1
Volume level, Adjusting ......................................................... 3-1
S
SD card ................................................................................. 6-1 W
Formatting ...................................................................... 6-2 Width
Inserting ......................................................................... 6-1 APF .............................................................................. 4-12
Saving data .................................................................... 6-1 Noise Blanker ................................................................. 4-5
Set mode ........................................................................ 8-9
Unmounting .................................................................... 6-2
Semi Break-in ....................................................................... 4-11
III
IC-7610 #13 < Intended Country of Use >
(Europe) AT BE CY CZ DK EE
FI FR DE GR HU IE
IT LV LT LU MT NL
PL PT SK SI ES SE
GB IS LI NO CH BG
RO TR HR
A7380D-1EX
Printed in Japan
© 2017 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan