Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of defective materials and faulty
workmanship. Contact your local sales office for warranty information. If warranted goods are
returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge
those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all other
warranties, expressed or implied, including those of merchantability and fitness for a
particular purpose. Specifications may change without notice. The information we supply is
believed to be accurate and reliable as of this printing. However, we assume no responsibility for its
use.
While we provide application assistance personally, through our literature and the Honeywell web
site, it is up to the customer to determine the suitability of the product in the application.
CE Conformity (Europe)
This product is in conformity with the protection requirements of the following European Council Directives:
73/23/EEC, the Low Voltage Directive, and 89/336/EEC, the EMC Directive. Conformity of this product with
any other “CE Mark” Directive(s) shall not be assumed.
Attention
The emission limits of EN 50081-2 are designed to provide reasonable protection against harmful
interference when this equipment is operated in an industrial environment. Operation of this equipment in a
residential area may cause harmful interference. This equipment generates, uses, and can radiate radio
frequency energy and may cause interference to radio and television reception when the equipment is used
closer than 30 meters to the antenna(e). In special cases, when highly susceptible apparatus is used in
close proximity, the user may have to employ additional mitigating measures to further reduce the
electromagnetic emissions of this equipment.
Honeywell
Industrial Measurement and Control
1100 Virginia Drive
Fort Washington, PA 19034
ii 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
About This Document
Abstract
This manual describes the installation and operation of the 7866 Triple Range Digital H2 and CO2
Analyzer/Indicator and Gas Sampling Panel and its digital controller.
Contacts
World Wide Web
The following lists Honeywell’s World Wide Web sites that will be of interest to our customers.
Corporate http://www.honeywell.com
Telephone
Contact us by telephone at the numbers listed below.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance iii
INSTRUCTIONS (European ATEX Directive 94/9/EC, Annex II, 1.0.6)
The following instructions apply to equipment covered by certificate number Sira 05ATEX1249X.
1. The equipment may be used with flammable gases and vapours with apparatus groups IIC with
temperature class T6.
2. The equipment is only certified for use in ambient temperatures in the range -10ºC to +50ºC and should
not be used outside this range.
3. Installation shall be carried out by suitably trained personnel in accordance with the applicable code of
practice, e.g. EN 60074-14:1997.
4. Inspection and maintenance of this equipment shall be carried out by suitably trained personnel in
accordance with the applicable code of practice, e.g. EN 60097-17.
5. Repair of this equipment shall be carried out by suitably trained personnel in accordance with the
applicable code of practice, e.g. EN 60079-19.
6. See Section 3 of this manual for installation instructions.
See Section 4 of this manual for set up instructions.
See Section 5 of this manual for calibration instructions.
7. Components to be incorporated into or used as replacement parts of the equipment shall be fitted by
suitably trained personnel in accordance with the manufacturer’s documentation.
8. The certification of this equipment relies upon the following material used in its construction:
Aluminum Alloy 356
If the equipment is likely to come into contact with aggressive substances, then it is the responsibility
of the user to take suitable precautions that prevent it from being adversely affected, thus ensuring that
the type of protection provided by the equipment is not compromised.
Aggressive substances: Acidic liquids or gases that may attack metals, or solvents
that may affect polymeric materials. (All gases specified by
Honeywell for use in this equipment are non-corrosive and non-reactive).
Suitable precautions: Regular checks as part of routine inspections or establishing
from the material data sheets that it is resistant to specific chemicals.
9. A copy of the certification marking can be found on page v of this manual and Honeywell drawing
51452210.
10. Detailed specifications for electrical, environmental and sample gas requirements for this product can
be found in Section 2 of this manual.
Special Conditions for Safe Use
The 7866 Thermal Conductivity Gas Analyzers shall not be used in carbon disulphide gas.
The 7866 Thermal Conductivity Gas Analyzers shall not be used to analyze gas samples with
an oxygen concentration higher that 21%.
The 7866 Thermal Conductivity Gas Analyzers shall not be used to analyze explosive gas
mixtures.
The 7866 Thermal Conductivity Gas Analyzers shall only be used to analyze gas samples at
pressures up to 2 lbf/in2 (13.8 Kpa).
iv 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Copy of the certification marking
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance v
Symbol Definitions
The following table lists those symbols that may be used in this document to denote certain conditions.
Symbol Definition
WARNING
PERSONAL INJURY: Risk of electrical shock. This symbol warns the user of a
potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms,
42.4 Vpeak, or 60 Vdc may be accessible. Failure to comply with these
instructions could result in death or serious injury.
Protective Earth (PE) terminal. Provided for connection of the protective earth (green
or green/yellow) supply system conductor.
Functional earth terminal. Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to protective earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground. Functional earth connection. NOTE: This connection shall be bonded
to Protective earth at the source of supply in accordance with national and local
electrical code requirements.
vi 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Contents
1. INTRODUCTION ................................................................................................... 1
1.1 Overview ........................................................................................................................................ 1
1.2 Sensing Unit ................................................................................................................................... 2
1.3 7866 Digital Controller .................................................................................................................. 4
1.4 Principles of Operation................................................................................................................... 7
1.5 Process Instrument Explorer Software ........................................................................................... 8
1.6 CE Conformity (Europe) .............................................................................................................. 10
3. INSTALLATION .................................................................................................. 19
3.1 Overview ...................................................................................................................................... 19
3.2 Sensing Unit Requirements and Location .................................................................................... 19
3.3 Mounting the Sensing Unit........................................................................................................... 20
3.4 Piping or Tubing Connections...................................................................................................... 20
3.5 Mounting the 7866 Digital Controller/Indicator .......................................................................... 23
3.6 Electrical Considerations.............................................................................................................. 26
3.7 Wiring Between Sensing Unit, Controller, and Indicator ............................................................ 27
3.8 Checklist....................................................................................................................................... 32
4. SET UP MODE.................................................................................................... 33
4.1 Overview ...................................................................................................................................... 33
4.2 Configuration Tips ....................................................................................................................... 33
4.3 Unit Set Up Group........................................................................................................................ 34
4.4 Alarms Set Up Group ................................................................................................................... 36
4.5 Communications Set Up Group.................................................................................................... 36
4.6 Calibration Group......................................................................................................................... 39
4.7 Status Group ................................................................................................................................. 39
4.8 P.I.E. Tool Ethernet and Email Configuration Screens................................................................ 39
4.9 Configuring your Ethernet Connection ........................................................................................ 42
4.9.1 Connecting to the Controller via Infrared Communications ............................................. 42
4.9.2 Connecting to the Controller via Ethernet Communications............................................. 44
5. CALIBRATION.................................................................................................... 47
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance vii
5.1 Overview ...................................................................................................................................... 47
5.2 Sensing Unit Calibration Warning ............................................................................................... 47
5.3 7866 Analyzer Input Calibration .................................................................................................. 48
5.4 7866 Remote Indicator Input Calibration..................................................................................... 51
5.5 Restoring Factory-set Input Calibration ....................................................................................... 52
5.6 Output Calibration ........................................................................................................................ 53
5.7 Security Lockout .......................................................................................................................... 54
5.8 Setting the Alarm Limits .............................................................................................................. 56
6. OPERATION ....................................................................................................... 59
6.1 Overview ...................................................................................................................................... 59
6.2 Operating Notes............................................................................................................................ 59
6.3 Operation ...................................................................................................................................... 59
7. MAINTENANCE .................................................................................................. 61
7.1 Routine Maintenance.................................................................................................................... 61
7.2 Parts Replacement ........................................................................................................................ 61
7.2.1 Sensing Unit ...................................................................................................................... 61
7.3 Repacking..................................................................................................................................... 64
7.4 Spare Parts.................................................................................................................................... 65
8. TROUBLESHOOTING ........................................................................................ 67
8.1 Overview ...................................................................................................................................... 67
8.2 Troubleshooting............................................................................................................................ 67
8.2.1 General .............................................................................................................................. 67
8.2.2 Recalibration...................................................................................................................... 67
8.2.3 Fault Isolation Tests........................................................................................................... 69
8.2.4 Additional Troubleshooting............................................................................................... 73
viii 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Tables
Table 1-1 Function of Keys ......................................................................................................................... 5
Table 1-2 Relative Thermal Conductivity of Common Gases..................................................................... 7
Table 3-1 Mounting Procedure ................................................................................................................... 25
Table 3-2 Permissible Wiring Bundling .................................................................................................... 27
Table 3-3 Terminals for connecting a UDC to a MDI Compliant Hub or Switch utilizing a cross-over
cable..................................................................................................................................................... 31
Table 3-4 Terminals for connecting a UDC directly to a PC utilizing a straight-through cable................. 31
Table 4-1 Configuration Tips..................................................................................................................... 33
Table 4-2 Controller Unit Group Function Prompts.................................................................................. 34
Table 4-3 Indicator Unit Group Function Prompts.................................................................................... 35
Table 4-4 Alarms Group Function Prompts............................................................................................... 36
Table 4-5 Communications Group Function Prompts ............................................................................... 36
Parameter Definition .................................................................................................................................. 36
Table 4-6 Status Group Function Prompts................................................................................................. 39
Table 5-1 Input Calibration for Range 1.................................................................................................... 48
Table 5-2 Input Calibration for Range 2.................................................................................................... 49
Table 5-3 Input Calibration for Range 3.................................................................................................... 50
Table 5-4 PV Input Calibration.................................................................................................................. 51
Table 5-5 Restoring Analyzer’s Factory-set Input Calibration Values...................................................... 52
Table 5-6 Restoring Indicator’s Factory-set Input Calibration Values...................................................... 52
Table 5-7 Output Calibration Procedure.................................................................................................... 53
Table 5-8 Entering the Security Code........................................................................................................ 54
Table 5-9 Changing Security Level ........................................................................................................... 55
Table 5-10 Alarm Adjustment Procedure .................................................................................................. 57
Table 7-1 Sensing Unit Cell Assembly Cable Connections....................................................................... 63
Table 7-2 Recommended Spare Parts ........................................................................................................ 65
Table 8-1 Coarse Zero Adjustment............................................................................................................ 68
Table 8-2 Binary Count Sequence for Coarse Zero Jumper Pattern .......................................................... 68
Table 8-3 Coarse-Zero Jumper Pattern ...................................................................................................... 69
Table 8-4 Troubleshooting Procedures ...................................................................................................... 70
Table 9-1 Replaceable Parts for 7872 Gas Sampling Panel....................................................................... 78
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance ix
Figures
x 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Introduction
1. Introduction
1.1 Overview
The Triple-Range Digital H2 and CO2 Analyzer/Indicator provides three ranges of measurement:
• Range 1: CO2 in Air
• Range 2: H2 in CO2
• Range 3: H2 in Air – See Table 5-3
The analyzer consists of three basic components: the sensing unit (transmitter), the control unit
(receiver)—both shown in Figure 1-1—and a power supply. The sensing unit is located at the sampling
site; the 7866 Digital Controller is arranged for panel mounting in a non-hazardous area.
The sensing unit receives a continuous flow of the binary or multi-component gas mixture, measures the
concentration of the sample gas and transmits an electrical signal to the control unit. The sensing unit is
ruggedly constructed to meet most environmental conditions and is designed to be mounted up to 1,000
feet from the control unit with only a single multi-conductor non-shielded cable connecting the two,
resulting in greater flexibility and lower installation costs.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 1
Introduction
2 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Introduction
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 3
Introduction
4 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Introduction
Key Function
• Places the controller in the Configuration Set Up group select mode. Sequentially displays Set
Setup
Up groups and allows the FUNC key to display individual functions in each Set Up group.
Func • Used in conjunction with the SETUP key to select the individual functions of a selected
Loop 1/2 Configuration Set Up group.
• Pressing this key saves, into nonvolatile memory, any changes made to previous function value
or selection.
• Used during field calibration procedure.
• Configuration Mode: Used to scroll through the parameter selections or to increase the selected
parameter value.*
• Configuration Mode: Used to scroll through the parameter selections or to decrease the selected
parameter value.*
* Changing Values Quickly: When changing the value of a parameter, you can adjust a more
significant digit in the upper display by holding in one key or , and pressing the other or
at the same time. The adjustment will move one digit to the left. Press the key again and you will
move one more digit to the left. Holding the or keys down will change the value twice as
quickly.
SP • Normal Operation: Used to toggle what is shown in the lower display—either the Range being
Select measured or its corresponding Gas.
Lower • Normal Operation: Used to scroll through the lower display selections:
Display
• If Range was selected (by pressing SP SELECT), selections are RANGE 1, RANGE 2, or
RANGE 3.
• If Gas was selected (by pressing SP SELECT), selections are CO2inAIR, H2in CO2, H2in
AIR (corresponding to Range 1, Range 2, and Range 3 respectively).
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 5
Introduction
Lower Display
Microampere Signal
RANGE x = Upper Display
from Sensor
Select Range 1, 2, or 3
OR Selected Range
Gas being measured 0 -100%
Select Range
Zero and Span Limits
R1 ZERO = Range 1 Zero 0% CO 2 (100% Air)
Carbon Dioxide
Range 1 = Purge
% Carbon Dioxide vs. Air 1 Out put Signal
0/4-20mA
R1 SPAN = Range 1 Span 100% CO 2 (0% Air)
6 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Introduction
CO 0.958
N2 0.989
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 7
Introduction
Features
• Create configurations with intuitive software program running on a Pocket PC, a Desktop or a
laptop computer.
• Create/edit configurations live, just connect software to the controller via a communications port.
• Create/edit configurations offline and download to controller later via a communications port.
• Communication types available on every 7866:
o Infrared (optional)
o RS 485 (optional)
o Ethernet (optional)
• Same port types on UDC controllers allow interconnectivity.
• This software is available in English, Spanish, Italian, German and French.
Infrared communications
The infrared connection provides a non-intrusive wireless connection with the instrument and maintains
NEMA4X AND IP66 integrity.
No need to get access to the back of the controller to communicate with the instrument, no need to take
your screw driver to wire the communication cable, no wiring mistake possible. You can now duplicate an
8 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Introduction
Question: What if I have several controllers on the same panel? How can I be sure I am communicating
with the correct one?
Answer: The infrared port of the controller is normally “off”. You activate the infrared port by pressing
any controller’s key. You can now communicate. After 4 minutes, the port will be shut down again. Each
controller may also be assigned a different communications address.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9
Introduction
ATTENTION
The emission limits of EN61326 are designed to provide reasonable protection against harmful interference when this
equipment is operated in an industrial environment. Operation of this equipment in a residential area may cause harmful
interference. This equipment generates, uses, and can radiate radio frequency energy and may cause interference to radio and
television reception when the equipment is used closer than 30 meters (98 feet) to the antenna(e). In special cases, when
highly susceptible apparatus is used in close proximity, the user may have to employ additional mitigating measures to further
reduce the electromagnetic emissions of this equipment.
WARNING
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be
impaired.
10 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Specifications and Model Selection Guide
2.1 Specifications
Performance
Accuracy ± 2 % of span (output signal) at reference conditions for binary gas mixtures
Linearity Within ± 2 % of span for most standard ranges. If linearity exceeds ± 2 % a correction curve is
supplied with the analyzer.
Ambient At sensing unit: Depends on range; typically less than 1 % F.S. over entire temperature range
Temperature
Influence
Atmospheric ± 0.01 % of span per inch H2O (± 0.05 % of span per mm Hg)
Pressure Influence
Sample Flow Rate Less than ± 0.5 % of span over flow range of 0.2 to 4 cfh (100 to 2000 cc/min)
Influence
Line Voltage Maximum 0.02 % of span for each 1 % change of line voltage
Influence
Operating
When measuring flammable gas mixture that contains oxygen, the maximum
oxygen concentration must not exceed 21%.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 11
Specifications and Model Selection Guide
Alarm Outputs One or two alarms are available; each uses an SPDT electromechanical relay.
Triple Range:
Two relay outputs for Alarm 1 and Alarm 2
Two current outputs to transmit PV and range information
Remote Indicator:
Two relay outputs for Alarm 1 and Alarm 2
Power Requirements Control Unit only: Universal supply 90 Vac to 264 Vac (consumption 18 VA maximum) or 24 Vac/dc
(consumption 12 VA maximum); 50 Hz to 60 Hz
Materials Contacting Sample contacts 316 stainless steel, Buna N, Teflon, glass and Viton
Sample Gas
Connections Sample inlet and outlet: 1/4” OD tubing (compression fittings supplied)
Reference gas inlet and outlet: 1/4” OD tubing (compression fittings supplied)
Electrical power inlet: Opening for 1/2” conduit (control unit only)
Sensing unit power inlet (24 Vdc from control unit): 1/2” NPT (female conduit)
12 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Specifications and Model Selection Guide
Communications: RS422/485 Modbus RTU Communications Baud Rate: 4800, 9600,19,200 or 38,400 baud
Interface (Optional) selectable
Length of Link:
2000 ft (600 m) max. with Belden 9271 Twinax
Cable and 120 ohm termination resistors
4000 ft. (1200 m) max. with Belden 8227
Twinax Cable and 100 ohm termination resistors
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 13
Specifications and Model Selection Guide
Control Unit:
Weight: 1.3 kg (3 lb.)
Dimensions: Bezel: 96 mm H x 96 mm W (3.78” H x 3.78” W)
Case: 92 mm H x 92 mm W x 192 mm D
(3.62” H x 3.62” W x 7.55” D)
Standards – This product is in conformity with the protection requirements of the following European Council
Control Unit Directives: 73/23/EEC, the Low Voltage Directive, and 89/336/EEC, the EMC Directive. Conformity of
this product with any other “CE Mark” Directive(s) shall not be assumed.
Installation Category Category II: Energy-consuming equipment supplied from the fixed
(Overvoltage installation, local level appliances, and Industrial Control Equipment.
Category):
Declaration of 51453681
Conformity:
14 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Specifications and Model Selection Guide
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection each from Table I using the column below the proper arrow.
A dot ( ) denotes unrestricted availability.
Analyzer includes sensor, control unit and power supply
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 15
Specifications and Model Selection Guide
Availability
None 000
MODBUS RS485 101
10 Base-T Ethernet (Modbus RTU) 102
TABLE VI - TAGGING
None 000
Linen Tags: 15 characters max. On each of three lines: 206
Specify legend. One mounted on Control Unit;
one on Sensing Unit.
Stainless Steel Tags: 208
15 characters max. On each of three lines:
Specify legend. One mounted on Control Unit;
one on Sensing Unit.
ACCESSORY PARTS
16 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Specifications and Model Selection Guide
Refer to Appendix A for ordering information on the optional 7872 Gas Sampling Panel.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 17
Specifications and Model Selection Guide
18 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
3. Installation
3.1 Overview
This section describes the installation requirements and procedures for the 7866 Triple Range Digital
Analyzer/Indicator.
Connections
Provide a three-conductor copper-wire cable (four-conductor if a solenoid calibrate valve is used) to
provide the connections between the sensing unit and the 7866 Digital Controller. Connecting
cable/conductors must be rated at 90ºC. The required wire size for each conductor is listed in Section 3.7
according to cable length. An adapter is supplied to terminate 1/2 inch threaded conduit and connect to the
sensing unit's watertight housing. The explosion-proof housing is tapped for 1/2 NPT conduit.
Clearance
Provide at least 12 inches clearance above the top of the sensing unit to allow the internal assembly to be
removed for servicing. Allow appropriate space below the sensing unit for 1/4 inch or 6 mm inlet and
outlet tubing connections. Position the sensing unit on a vertical surface with the inlet and outlet fittings at
the bottom. Allow space at the right-hand opening for the solenoid calibrate valve, which, if supplied, is to
be mounted here.
Sampling System
Provide a sampling system to deliver a clean and relatively dry sample at a rate of 100 to 2000 cc per
minute. The sample should be free of dust.
Calibrating Gases
Provide a source of calibrating gases; e.g., cylinders of compressed zero gas and span gas with pressure
regulating valves on each. In general, a zero gas contains all gas components in the sample stream except
the measured gas. For suppressed-zero ranges, zero gas contains measured gas at or slightly above the low-
end value. Concentrations should be those normally present in the stream. A span gas contains all of the
gases in the sample stream at expected concentrations with measured gas concentration accurately
analyzed. Concentration of water (vapor) in the calibrating gas should be the same as that in the
background gas. Therefore, a gas saturator or dryer may be required.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 19
Installation
Reference Gas
Provide a source of reference gas, if required. If hydrogen or helium, supply at 0.02 cfh to 0.2 cfh
(10 cc/min to 100 cc/min). Vent to atmospheric pressure. (If hydrogen, vent to a safe ventilating system.).
If flowing air is required, supply at 0.5 cfh to 2.0 cfh (250 cc/min to 1000 cc/min). Vent to atmospheric
pressure.
The sensing unit is designed as explosion-proof. Dimensions for this unit are shown in Figure 3-1.
Electrical conduit must be used for all wiring and the openings are fitted for 1/2-inch conduit.
Mount the explosion-proof sensing unit in accordance with Figure 3-1.
Types of Tubing
Any metal and most plastic tubing can be used provided it is chemically compatible with the sample gas.
Avoid the use of plasticized PVC or other soft tubing at the sensing-unit compression fittings and do not
use tubing having an inside diameter less than 4 mm.
20 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
Making Connections
CONNECTION DAMAGE
• Excessive tightening on metal tubing may damage the O-ring.
• Excessive tightening on plastic tubing may restrict the opening.
Failure to comply with these instructions may result in product damage.
Step Action
1 Cut the tubing squarely and remove all burrs, loosen the compression nut.
2 Push the tubing firmly into fitting until it slips through the O-ring and seats against the metal.
3 Tighten the compression nut by hand; then turn it about 1/8 turn with a wrench. If the entire fitting
assembly turns, use a back-up wrench.
4 If a good seal does not result, remove the compression nut and slide it onto the tubing, take out the
small O-ring and slip it on the tubing, then assemble the fitting.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 21
Installation
166 Removable
6.53 Threaded
Cover
1/2"
NPT
9
.35 DIA.
156
6.14
*
Sample Sample Left Side View
Outlet Inlet
56
2.20 *For 1/4” O.D. or 6 mm O.D.
114 DIA Metal or Plastic Tubing
4.48 DIA
140
5.51 NOTE:
1. Weight of unit is approximately 18-3/4 lb. (8.5 kg)
2. Wiring diagram is ID-2071-356.
Front View
22 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
The controller is considered “rack and panel mounted equipment” per the following safety standards:
For US, ANSI/ISA S82-1994
For Canada, CAN/CSA – C22.2 No. 1010.1-92
For Europe, EN610101-1
Conformity with these standards requires the user to provide adequate protection against a shock hazard. The user
shall install this controller in an enclosure that limits OPERATOR access to the rear terminals.
If the controller is used in a manner not specified by Honeywell, the protection provided by the equipment may be
impaired.
Physical Considerations
The controller can be mounted on either a vertical or tilted panel using the mounting kit supplied. Adequate
access space must be available at the back of the panel for installation and servicing activities.
• Overall dimensions and panel cutout requirements for mounting the controller are shown in Figure
3-2.
• The controller’s mounting enclosure must be grounded according to CSA standard C22.2 No. 0.4 or
Factory Mutual Class No. 3820 paragraph 6.1.5.
• The front panel is moisture rated NEMA3 and IP55 rated and can be easily upgraded to NEMA4X and
IP66. See Figure 3-3 and Table 3-1 Mounting Procedure.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 23
Installation
Overall Dimensions
90,6 108,6
92,0 + 0,8 3.57 4.28
- 0,00 Panel
3.62 + 0.03 Cutout
-0.00
Mounting Notes
Before mounting the controller, refer to the nameplate on the outside of the case and make a note of the
model number. It will help later when selecting the proper wiring configuration.
Mounting Method
Before mounting the controller, refer to the nameplate on the outside of the case and make a note of the
model number. It will help later when selecting the proper wiring configuration.
24 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
Mounting clips
Attach screws and
washers here for
water protection
Mounting Procedure
Table 3-1 Mounting Procedure
Step Action
1 Mark and cut out the controller hole in the panel according to the dimension information in Figure
3-2.
2 Orient the case properly and slide it through the panel hole from the front.
3 Remove the mounting kit from the shipping container and install the kit as follows:
• For normal installation (NEMA 3/IP55) two mounting clips are required. Insert the prongs
of the clips into the two holes in the top and bottom center of the case
• For water-protected installation (NEMA 4/IP66) four mounting clips are required. There
are two options of where to install the mounting clips:
1) Insert the prongs of the clips into the two holes on the left and right side of the top and
bottom of the case or
2) on the center on each of the four sides.
• Tighten screws to 2 lb-inch (22 N•cm) to secure the case against the panel. CAUTION:
Over tightening will cause distortion and the unit may not seal properly.
4 For water-protected installation (NEMA 4/IP66), install four screws with washers into the four
recessed areas in the corners of the front bezel (Figure 3-3). Push the point of the screw through
the center piercing the elastomeric material and then tighten screws to 5 lb-in (56 N•cm).
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 25
Installation
Applying 90-264 Vac to an instrument rated for 24 Vac/dc will severely damage the
instrument and is a fire and smoke hazard.
When applying power to multiple instruments, make certain that sufficient current is supplied. Otherwise,
the instruments may not start up normally due to the voltage drop caused by the in-rush current.
Controller Grounding
PROTECTIVE BONDING (grounding) of this controller and the enclosure in which it is installed shall be
in accordance with National and Local electrical codes. To minimize electrical noise and transients that
may adversely affect the system, supplementary bonding of the controller enclosure to a local ground,
using a No. 12 (4 mm2) copper conductor, is recommended.
Control/Alarm Circuit Wiring
The insulation of wires connected to the Control/Alarm terminals shall be rated for the highest voltage
involved. Extra Low Voltage (ELV) wiring (input, current output, and low voltage Control/Alarm circuits)
shall be separated from HAZARDOUS LIVE (>30 Vac, 42.4 Vpeak, or 60 Vdc) wiring per Permissible
Wiring Bundling, Table 3-2.
Electrical Noise Precautions
Electrical noise is composed of unabated electrical signals, which produce undesirable effects in
measurements and control circuits.
Digital equipment is especially sensitive to the effects of electrical noise. Your controller has built-in
circuits to reduce the effect of electrical noise from various sources. If there is a need to further reduce
these effects:
• Separate External Wiring—Separate connecting wires into bundles
(See Permissible Wiring Bundling - Table 3-2) and route the individual bundles through separate
conduit metal trays.
Use Suppression Devices—For additional noise protection, you may want to add suppression devices
at the external source. Appropriate suppression devices are commercially available.
ATTENTION
For additional noise information, refer to document number 51-52-05-01, How to Apply Digital
Instrumentation in Severe Electrical Noise Environments.
26 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
Step Action
1 After the sensing unit is mounted, carefully remove the top threaded cover by turning it
counterclockwise. (Loosen the set screw.)
2 Two openings are provided for cable entrance; make certain the plug screw is tightened firmly into
the unused right-hand opening.
3 Use 1/2 NPT threaded electrical conduit, and mount the special adapter fitting supplied with the
analyzer.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 27
Installation
Earth
1 Ground
3 2 10 19 28
AC/DC Hot
L1 11 20 29
Line Neutral
Voltage L2/N 12 21 30
4 13 22 31
5 14 23 32
6 15 24 33
7 16 25 34
8 17 26 35
18 27 36
9
2 It is the user’s responsibility to provide a switch and non -time delay (North America),
quick-acting, high breaking capacity, Type F (Europe), 1/2A, 250V fuse(s), or circuit -
breaker for 90-264 Vac applications; or 2 A, 125 V fuse or circuit breaker for 2 4 Vac/dc
applications, as part of the installation.
28 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
10 19 28
L1 11 Sensor 20 29
Range
L2/N 12 21 30
4 13 22 31
5 14 Alarm 2 23 32
PV Output
0-20 or 4-20 mA 33
6 15 24
7 16 25 34
Range Output
0-20 or 4-20 mA 8 17 Alarm 1 26 Sensor + 35
27 Input - 36
9 18
250 Ohm
Digital Controller
10 19 28
L1 11 20 29
L2/N 12 21 30
4 13 22 31
5 14 Alarm 2 23 Range + 32
24 Input - 33
6 15
7 16 25 34 250 Ohm
8 17 Alarm 1 26 PV + 35
27 Input - 36
9 18
250 Ohm
Digital Indicator
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 29
Installation
COMMUNICATION MASTER
26 D+ (B) D+
27 D– (A) D–
120 OHMS
Connect shield
TO OTHER to ground at one
COMMUNICATION
CONTROLLERS
end only.
D– D+
10 19 28
Ethernet
L1 11 20 29
Adaptor
L2/N 12 21 30
4 13 22 31
5 14 23 32
6 15 24 33
Ethernet
7 16 25 Cable
34 To 24
Hub
35or
8 17 26
9 18 27 36
30 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Installation
COMMUNICATION MASTER 3
SHLD TXD - TXD + RXD - RXD +
4 SHLD 1
24 RXD +
25 RXD -
26 TXD +
27 TXD -
Table 3-3 Terminals for connecting a UDC to a MDI Compliant Hub or Switch utilizing a
cross-over cable
UDC Terminal UDC Signal Name RJ45 Socket Pin # Switch Signal Name
Position 4 Shield Shield Shield
Position 24 RXD- 6 TXD-
Position 25 RXD+ 3 TXD+
Position 26 TXD- 2 RXD-
Position 27 TXD+ 1 RXD+
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 31
Installation
3.8 Checklist
Check # Action
1 Check all wiring and piping. Make certain all fittings are tight. Replace the top threaded cover
on the sensing unit and tighten the set screw, if provided. No operating checks or settings are
required in the sensing unit.
2 Shut off or vent the gas flow at the sampling system to make sure sample will not flow into the
analyzer during startup.
The test meter used, whether for voltage or current output, should be a digital voltmeter or a millivolt
potentiometer for best accuracy. It should have an input impedance greater than 2000 ohms.
• Do not open the threaded cover of the sensing unit unless the power source is disconnected. Then loosen the set
screw to permit threaded cover to be turned.
Failure to comply with these instructions could result in death or serious injury.
32 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
4. Set Up Mode
4.1 Overview
This section describes the steps to configure the 7866 Controller/Indicator for your application.
Displaying Groups Use the SET UP key to display the Set Up groups.
Displaying Use the FUNCTION key to display the individual parameters under each group. The prompts
Functions are listed in the order they appear in each group.
Scrolling If the SET UP key is held in, the Group prompts scroll continuously at a rate of once every 2/3
of a second.
Holding in either the or key will increase the scroll rate to once every 1/3 of a second in
the forward or reverse direction while viewing Group prompts.
Changing Values When changing the value of a parameter, you can adjust a more significant digit in the upper
Quickly display by holding in one key or , and pressing the other or at the same time. The
adjustment will move one digit to the left. Press the key again and you will move one more
digit to the left.
Timing Out from If you are in Set Up mode and do not press any keys for 30 seconds, the controller will time
Set Up Mode out and revert to normal operation.
Key Error When a key is pressed and the prompt "KEY ERROR" appears in the lower display, it will be
for one of the following reasons:
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 33
Set Up Mode
34 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 35
Set Up Mode
Function Prompts
Table 4-5 Communications Group Function Prompts
Function Prompt Selections or Parameter
Lower Display Range of Setting Definition
Upper Display
Com ADDR 1 to 99 COMMUNICATIONS STATION ADDRESS—This is
a number that is assigned to a controller that is to be
used with the communications option. This number
will be its address. This value is also used for IR
transactions. To communicate with Pocket PC set
address to 3.
ComSTATE COMMUNICATIONS SELECTION—enables the
RS-485 or Ethernet communications port.
DISABLE DISABLE—Disables communications option.
MODBUS MODBUS—Enables RS-485 Modbus RTU
communication port. Appears only when a
communications board is installed.
ETHERNE ETHERNET—Enables Ethernet communications
port. Appears only when a communication board is
installed.
36 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
0 1 2 3
seeeeeee emmmmmmm mmmmmmmm mmmmmmmm
Where:
s = sign, e = exponent, m = mantissa bit
FP_B 0 1 2 3
FP_BB 1 0 3 2
FP_L 3 2 1 0
FP_LB 2 3 0 1
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 37
Set Up Mode
38 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 39
Set Up Mode
representative as to how these should be configured for your installation. The MAC address is printed on
the product label located on the instrument’s case.
These settings can be changed via the Ethernet Configuration Screen as shown in Figure 4-1.
See Section 4.9 – Configuring your Ethernet Connection for more information.
WARNING
After you change the IP Address, you will no longer be able to communicate with the instrument via
Ethernet until you change the P.I.E. Tool’s IP Address setting in the “PC COMM SETUP” to match the
setting that is now in your controller.
40 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
ATTENTION
Instruments will always send Email time-stamped with the date that the Ethernet Software in the
instrument was last modified.
If the SMTP address on your network is changed, such as can happen when a server is replaced, then
you must reconfigure the Email SMTP IP address in this instrument to match.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 41
Set Up Mode
42 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
Press any button on the controller’s keyboard to activate the controller’s IR port. Point your IR dongle (if
using PC) or your Pocket PC’s IR port (if using Pocket PC) at the IR window on the front of the controller
and then click on the “Start” button. The P.I.E. Tool® should start uploading the configuration information
from the controller as shown below:
Once the upload is complete, click on the “Ethernet & Email” Group. Configure your Ethernet and Email
parameters per Section 4.8.
Once you have changed the Ethernet settings and downloaded them to your controller, you will now be
able to communicate with it via Ethernet.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 43
Set Up Mode
WARNING
Connecting to the Controller via Ethernet Communications requires that you change your PC’s IP settings.
If you have never done this before, then it is strongly recommended that you consult with your Information
Technologies (IT) representative before proceeding.
First, write down the current IP Address, Subnet Mask and Default Gateway settings for your PC. Put these
someplace that you can find them later.
Connecting to the Ethernet Port in the Controller requires that you have either an Ethernet crossover cable
or a MDI-compliant Switch or Hub available with a straight-through cable. The crossover cable can be
used to directly connect your PC to the Controller while the Switch or Hub can be used to connect your PC
and Controller to the Hub or Switch via straight-through cables.
Once you have made an Ethernet connection between your PC and the controller, then change the Local
Area Network (LAN) settings on your PC to be as follows:
IP Address: 10.0.0.3
Subnet Mask: 255.255.255.0
Default Gateway: 10.0.0.1
44 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Set Up Mode
Open your P.I.E. Tool® program and select “PC Comm Setup”.
Now configure your “Communication Type” to Ethernet and your Ethernet address to 10.0.0.2 as shown in
Figure 4-5.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 45
Set Up Mode
Close the Ethernet configuration window and then single click on the “Online Configuration” button.
Then, click on the “Start” button. The P.I.E. Tool® should start uploading the configuration information
from the controller as shown below:
Once the upload is complete, click on the “Ethernet & Email” Group. Configure your Ethernet and Email
parameters per Section 4.8.
Once you have changed the Ethernet settings and downloaded them to your controller, you will no longer
be able to communicate with it until you change the IP address in the P.I.E. Tool® to the controller’s new
IP Address.
You will also need to re-configure the Local Area Network (LAN) settings on your PC back to their
original settings. On some PCs and LANs, it is possible to simply allow the PC to get these settings
automatically via the DHCP server. Contact your Information Technologies (IT) representative to see if
this is available on your PC.
46 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Calibration
5. Calibration
5.1 Overview
Analyzer calibration
The 7866 analyzer is calibrated at the factory before shipping. The analyzer must be field-calibrated prior
to operation. The input calibration procedure includes:
• Setting the Zero for Range 1: 100 % Air; 0 % CO2
• Setting the Span for Range 1: 0 % Air; 100 % CO2
• Setting the Zero for Range 2: 100 % CO2; 0 % H2
• Setting the Span for Range 2: 0 % CO2; 100 % H2
• Setting the Zero for Range 3: 100 % H2; 0 % N2
• Setting the Span for Range 3: 75 % H2; 25 % N2
Indicator calibration
The 7866 Indicator is calibrated at the factory before shipping. You do not need to recalibrate it before
operating it.
The PV Input selection is factory set for 1-5V to be consistent with the Analyzer output of 4-20mA. If you
change the analyzer output to 0-20 mA you must change the PV Input to 0-5V. Recalibration is not
necessary because the indicator automatically rescales the input values.
The PV Input calibration procedure includes:
• Setting the Zero for the PV Input
• Setting the Span for the PV Input
Other
This section also includes the procedures for:
• field-calibrating the current output(s),
• entering a security code,
• changing the security level, and
• setting alarm limits.
• Do not open the threaded cover of the sensing unit unless the power source is disconnected. Then loosen the set
screw to permit threaded cover to be turned.
• Before making any test with power applied to the sensing unit, either remove the sensing unit to a non-hazardous
area or verify that the atmosphere is free from combustible gases.
Failure to comply with these instructions could result in death or serious injury.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 47
Calibration
6 FUNCTION Captures the displayed value. The display will blink once indicating that you can
use the or keys to change to the desired zero value. (This ties the internal
counts processed for the input conversion to the desired value for Zero.)
Connect the CO2 source to the sensor. The value shown in the Upper Display is a
"live" reading. Wait until the value becomes stable.
8 FUNCTION Captures the displayed value. The display will blink once indicating that you can
use the or keys to change to the desired span value. (This ties the internal
counts processed for the input conversion to the desired value for Span.)
9 FUNCTION Saves Range 1 SPAN data and processes the Range 1 calibration calculation.
If, after the Zero or Span "live" value has stabilized, no change is made, you should still perform the same key-press
sequences. For example, if in Step 5 you make no change to the displayed value, continue to Step 7 by pressing the
FUNCTION key twice.
48 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Calibration
6 FUNCTION Captures the displayed value. The display will blink once indicating that you can
use the or keys to change to the desired zero value. (This ties the internal
counts processed for the input conversion to the desired value for Zero.)
Connect the H2 source to the sensor. The value shown in the Upper Display is a
"live" reading. Wait until the value becomes stable.
8 FUNCTION Captures the displayed value. The display will blink once indicating that you can
use the or keys to change to the desired span value. (This ties the internal
counts processed for the input conversion to the desired value for Span.)
9 FUNCTION Saves Range 2 SPAN data and processes the Range 2 calibration calculation.
If, after the Zero or Span "live" value has stabilized, no change is made, you should still perform the same key-press
sequences. For example, if in Step 5 you make no change to the displayed value, continue to Step 7 by pressing the
FUNCTION key twice.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 49
Calibration
Some confusion is possible as 100 % H2 is referred to as the span for Range 3 and 75 % H2 is referred to as the
Zero. This is a carry over from the original analog circuitry.
Range 3 is used during normal operation to detect Hydrogen loss and therefore to detect potentially
dangerous process situations. The implication is that air is replacing the Hydrogen in the system. The
standard display range is 100 % to 75 % Hydrogen. Since Air represents a significant hazard due to its
Oxygen content, a mixture of 75 % Hydrogen and 25 % Nitrogen is used to calibrate the instrument at the
low operating range of the scale. Nitrogen is an acceptable substitute since its heat capacity characteristics
are very close to Oxygen. Since Air is composed of roughly 80 % Nitrogen and 20 % Oxygen, the error is
insignificant.
Span and Zero are reversed for this range as the initial input should be the same as the Range 2 Span. Calibration
progresses from Span to Zero for this range.
If, after the Zero or Span "live" value has stabilized, no change is made, you should still perform the same key-press
sequences. For example, if in Step 5 you make no change to the displayed value, continue to Step 7 by pressing the
FUNCTION key twice.
50 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Calibration
1 Connect the input source to the PV Input terminals. Set the source value to the
zero value.
6 FUNCTION Captures the displayed value. The display will blink once indicating that you can
use the or keys to change to the desired zero value. (This ties the internal
counts processed for the input conversion to the desired value for Zero.)
Set the source to the span value. The value shown in the Upper Display is a "live"
reading. Wait until the value becomes stable for the span value.
8 FUNCTION Captures the displayed value. The display will blink once indicating that you can
use the or keys to change to the desired span value. (This ties the internal
counts processed for the input conversion to the desired value for Span.)
9 FUNCTION Saves Input SPAN data and processes the Range 1 calibration calculation.
If, after the Zero or Span "live" value has stabilized, no change is made, you should still perform the same key-press
sequences. For example, if in Step 5 you make no change to the displayed value, continue to Step 7 by pressing the
FUNCTION key twice.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 51
Calibration
3 or Select RESTOR to restore factory calibration for desired Range input parameters.
3 or Select RESTOR to restore factory calibration for desired Range input parameters.
52 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Calibration
Before doing an output calibration, make sure the PV current output type (CUR OUT) selection in the Unit Set Up
group (Table 4-2) is configured properly for either 4-20 mA or 0-20 mA. This selection must agree with what you are
measuring for the output current to be calibrated correctly.
A four-digit value appears in the Upper Display. Use the or keys to change
the value until the milliampere output, on the meter, is at the desired reading
(4 mA or 0 mA).
5 FUNCTION Saves the SPAN VAL data and terminates the calibration procedure.
A field calibration will overwrite the manufacturing values. You cannot restore the factory-set output
calibration.
The output range of the current output used to transmit ranging data to the Indicator is fixed at 4-20 mA
and is not changeable in the field.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 53
Calibration
54 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Calibration
5 or Select NONE.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 55
Calibration
Alarm 1
Ideally the sealed system is filled to 100 % Hydrogen. As the hydrogen percentage falls the first alarm will
engage. The default setting is 98.0 %. The alarm setpoint can be adjusted to suit the process requirement.
When the alarm trips the normally open relay will de-energize and the relay contact will close. This relay
contact can be used to interlock the system with the main process controller or wired to an alarm bell or
flasher.
See wiring diagram in Section 3.7 for more detail (Figure 3-5) on the alarm terminal configuration.
Alarm 1 may also be used to call for make up Hydrogen. The alarm will activate when the measured
percentage of hydrogen falls below the setpoint. A deadband, also called “hysteresis”, will prevent clearing
of the alarm until the measured Hydrogen is below the setpoint by 0.5 percent.
Alarm 2
(mutually exclusive with 4-20 ranging output)
When installed, the second alarm is intended to identify significant losses of Hydrogen. Alarm 2 is set to
90.0 percent Hydrogen at the factory. This alarm should be set to warn operators and the main process
control system of impending danger. With the inclusion of Air in the hydrogen filled system, there is a
serious possibility of combustion. The relay contact that is linked with this alarm should be wired to an
alarm annunciating horn, flasher, and/or shutdown safety system.
Alarm 2 is connected to Relay Output #1. See wiring diagram in Section 3.7 for more detail (Figure 3-5) on the alarm
terminal configuration.
Alarm will activate when the measured percentage of hydrogen falls below the setpoint. A deadband, also
called “hysteresis”, will prevent clearing of the alarm until the measured Hydrogen is above the setpoint by
0.5 percent.
56 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Calibration
2 FUNCTION You will see ALARM1LO in the Lower Display. This is the Alarm 1 setpoint, low
alarm type.
4 FUNCTION You will see ALARM2LO in the Lower Display. This is the Alarm 2 setpoint, low
alarm type
6 FUNCTION You will see HYSTERiS in the Lower Display. This is the Alarm Hysteresis which
sets the deactivation range for both alarms.
The 7866 should be supplemented with additional safety systems where possible and appropriate. Pressure loss
detectors and redundant gas loss detectors are recommended in critical applications. The user always assumes the
responsibility of the correctness of the safety system design. It is always recommended that the installer, designer,
and user consult with their insurance company, local authorities, and industry guidelines on such matters.
The alarm will activate when the measured percentage of hydrogen falls below the setpoint. A deadband, also called
“hysteresis”, will prevent clearing of the alarm until the measured Hydrogen is above the setpoint by 0.5 percent.
Failure to comply with these instructions could result in death or serious injury.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 57
Calibration
58 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Operation
6. Operation
6.1 Overview
This section describes operating guidelines and procedures for the 7866 Digital Analyzer.
6.3 Operation
The digital display will indicate measured value to the limit of the design range. If the signal from the
sensor is outside the range, the display value will flash a range message. In extreme cases, a recalibration
may be required. However, normal variations due to changing gas flow rates and environmental factors
may cause signal drift.
The alarm relays are normally energized when no alarm condition exists; therefore, the contacts will go to
their alarm position upon loss of line voltage to the controller. Alarm limits can be set by pressing the SET
UP key to enter the Set Up mode. The Alarms Set Up group can then be entered to adjust the setpoints of
Alarm 1 and Alarm 2. Alarm circuits are inoperative when Range 1 and Range 2 are selected. As soon as
the controller is switched to Range 3, the alarms are activated.
Two alarms can be available, each one with its own separate relay contact. When power is OFF, the relays
are de-energized and their normally open contacts are non-conducting (open). When the alarms are
operating, but there is no violation of the limits, the relays are energized and the relays’ normally open
contacts are conducting (closed). When an alarm limit is violated the specific relay will de-energize and
create an open circuit. The open circuit can be used to activate an external device.
Alarm 1 is a LOW Alarm type. Alarm 1 will trip and remain on whenever the measured percentage goes
below the entered value. Alarm 1 typically is used as a first warning and to signal the need for make-up
hydrogen gas. A typical setting may range from 96.0 % to 98.0 %. The setting of Alarm 1's limit is the
responsibility of the user to determine. Consult your safety engineer or insurance company for proper
operating parameters.
Alarm 2 is also a LOW Alarm type. This alarm is typically used to indicate an increasingly dangerous loss
of hydrogen from the system. As air replaces hydrogen in the system, the probability of combustion
increases. Alarm 2 is typically used to activate an emergency shutdown circuit and/or to activate an
annunciating horn or siren. In this situation, the process may need to be purged to achieve a safe gas
mixture. The specific alarm limit and proper procedures to handle a low hydrogen situation is the
responsibility of the user to determine. Consult your safety engineer or insurance company for proper
operating parameters.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 59
Operation
To adjust Alarm Limit 1 or 2, refer to Section 5.8 Setting the Alarm Limits. Please note that extreme values
will not be accepted by the controller. For example, an illogical value greater than 100.0 will be
automatically overwritten by the controller with a “100.0”.
Check calibration with zero and span gases about once each week. Always allow enough time (possibly
several minutes) for a stable response. If the reading at the output device is not correct, adjust zero and
span, using zero and span gases, in accordance with the procedures as described in Section 5.3 7866
Analyzer Input Calibration. If only a slight zero-gas error exists, it can be corrected without rechecking the
span gas. However, this must be considered a temporary correction and the calibration must be readjusted
using both zero and span gas before another adjustment is made.
60 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Maintenance
7. Maintenance
To remove the threaded cover, turn it counterclockwise and lift it off to expose all terminal board
connections.
To remove the sensor assembly from its housing, first remove all connections at the terminal board and
loosen the two screws (captive) in the cutouts at either side of the round circuit board. Carefully pull up on
the handle as shown in Figure 1-2 to withdraw the entire unit.
Circuit Card
Remove the sensor assembly as described above. Then loosen the two captive screws on the underside of
the plastic platform to free the entire circuit-card assembly. Carefully unsolder the 12 leads connecting the
circuit card and cell assembly. The solder posts to which each lead is connected is identified in Table 7-1
by the wire color code and the letters adjacent to each post. Note that two of the leads go to the jumper
posts (S&T) on the platform.*
*If the circuit card is replaced, note that the standard R18 for most standard ranges is 1.5 K ohms and the
new card may require the R18 resistor taken from the old card depending upon the range.
Cell-Block Assembly
Remove the circuit card as described above. It is necessary to unsolder the interconnecting wires. Remove
the two screws in the top platform and carefully separate the parts, sliding the platform along the wires.
Remove the two screws in the large plastic sleeve and carefully slide this along the wires.
This provides access to the top of the block, allowing removal of heaters and thermistors. Identify the leads
before unsoldering them from the bottom of the circuit card. See Table 7-1.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 61
62
Maintenance
Figure 7-1 Sensing Unit Mother and Daughter Circuit Cards Parts List
MEASURING THERMISTOR HEATERS
THERMISTOR
THERMISTOR
7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance
9/06
Maintenance
E (1) White/brown
Temperature-Sensing Thermistors
These thermistors are the small hex-head assemblies. The leads are permanently attached. Unscrew the
assembly and remove from the cell block. Coat the threads with silicone grease before reinstalling to insure
a good thermal contact. Replacements are complete units, including leadwire.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 63
Maintenance
7.3 Repacking
When repacking for shipment, seal the sensor assembly inlet and outlet ports with tape to prevent packing
material from clogging these ports.
1
1
2
2 3
4
3
6
4
7
8
5
9
Figure 7-2 Gas Inlet and Outlet Fitting Parts
64 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Maintenance
Lower O-ring
For Gas Fittings, Viton A 31005724 8
For G = 3 and range -- Suffix D is 075, use Buna N 31082102 5
Middle O-ring
For explosion-proof Gas Fittings, Viton A 082049 4
For G = 3 and range -- Suffix D is 075, use Buna N 31075745 4
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 65
Maintenance
66 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Troubleshooting
8. Troubleshooting
8.1 Overview
This section describes various possible problems and the means to correct them.
8.2 Troubleshooting
8.2.1 General
If trouble is encountered in the adjustment of zero, refer to Section 8.2.2 Recalibration for adjustment
procedures. If current flow in the sensing unit-7866 Digital Controller leads cannot be adjusted for 200
microamperes to 500 microamperes, refer to Step 2 in Table 8-4. Alarm circuit problems can usually be
solved by referring to Section 5.8 Setting the Alarm Limits.
Note that alarm circuits will not activate unless the controller/indicator is set to Range 3.
8.2.2 Recalibration
A routine procedure for checking calibration is presented in Table 8-1 Coarse Zero.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 67
Troubleshooting
1 Open the sensing unit and observe the jumper pattern used at the top of the round circuit card
(terminal board at bottom). Note that each pin provided for the six jumpers is identified with a 1
or a 0. Determine the binary number formed by the jumper positions used and record this
number. The letters identify the color of the corresponding jumper.
2 If the analyzer output current or voltage is above zero or other low-end value and the ZERO
adjuster is at its counterclockwise limit, determine that binary number which is one digit lower
than the number recorded and change the necessary jumper positions to form this number.
For example, if the jumpers are positioned to form binary number 111001, then the jumpers
must be repositioned to form the next lower number binary 111000. Change the sixth jumper
from 1 to 0.
If the analyzer reading is below the low-end range value and the ZERO is at its clockwise
limit, the zero must be shifted upscale. Position the jumpers to form the next higher number,
e.g., from binary 011010 to 011011. Move the right-end jumper from 0 to 1.
Refer Table 8-2 for the sequence used in binary counting. The card is screened with MSB
(Most Significant Bit) and LSB (Least Significant Bit).
3 The above jumper change should permit the return of fine ZERO adjuster R16 to its center-of-
travel position and allow completion of the analyzer zero adjustment. If it does not, simply
increase or decrease the binary number by one digit more. A change of one binary count is
equivalent to one-half travel of control unit ZERO (R16). If jumpers are changed inadvertently
before the binary number has been recorded (or if thermistor detectors have been replaced)
re-establish the correct jumper pattern. Measure the sensing-unit current output by connecting
a meter in series with terminal 12 at the sensing unit while zero-gas flows through the sensing
unit. Proceed through the steps in Table 8-3 in numerical sequence only until the current
output measures between 250 µA and 240 µA. Jumpers that have been placed in their final
positions, not been moved, are marked X. Start with binary 32 (100000).
Table 8-2 Binary Count Sequence for Coarse Zero Jumper Pattern
MSB LSB MSB LSB MSB LSB MSB LSB
68 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Troubleshooting
Step If current is G Y O R N K
1 above 450 µA 1 0 0 0 0 0
below 250 µA 0 1 0 0 0 0
1 1 0 0 0 0
2 above 450 µA X 0 1 0 0 0
below 250 µA X 1 1 0 0 0
3 above 450 µA X X 0 1 0 0
below 250 µA X X 1 1 0 0
4 above 450 µA X X X 0 1 0
below 250 µA X X X 1 1 0
5 above 450 µA X X X X 0 1
below 250 µA X X X X 1 1
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 69
Troubleshooting
1. Blank display 1a. No line voltage. 1a. Check for correct voltage at terminals L1/H
and L2/N.
1b. Replace the display.
2. Cannot adjust for zero 2a. ZERO adjuster in 7866 Digital 2a. Adjust coarse ZERO in sensing unit in
signal with “zero” gas. Controller is out of adjusting accordance with the Coarse Zero Adjustment.
range.
2b. Open signal circuit. (Causes 2b. Check interconnecting wiring between 7866
below-zero signal.) Digital Controller and sensing unit for
continuity.
2c. Detector unbalance is too 2c. With “zero” gas flowing, connect a high-
large. impedance voltmeter (on 5 V range) first
between pins A and E, then between pins A
and C.
70 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Troubleshooting
3. Insufficient span with 3a. Faulty current regulator for 3a. Check for 3.75 volts ± 0.4 volts between pin E
“span” gas flowing detector bridge. and terminal 13. (This is equivalent to
and SPAN checking bridge current for 55 mA ± 5 mA.)
ADJUSTER turned
fully clockwise. 3b. Faulty sensing-unit amplifier. 3b. Disconnect the lead at terminal 12 in the
sensing unit and connect a 0-1 mA current
meter across terminals 12 (+) and 13 (–).
Refer to Table 8-2 and increase the coarse-
zero binary count (on the coarse-zero jumper
pattern described in the Course Zero
Adjustment procedure) by one number.
Current flow should increase about 250 uA.
This verifies that gain is normal.*
3c. Damaged measuring 3c. Connect a millivolt meter across circuit points
detector. A and D (at center of round card). Make the
zero adjustment in accordance with the Re-
calibration procedure. Pass a span-gas
mixture equivalent to a full-scale
measurement through the sensing unit. The
meter reading for 1% H2 should be at least 10
mV.** If it is less, the detectors must be
cleaned or replaced.
4. Slow response. 4a. Low flow rate. 4a. Increase flow rate to 2000 cc/min. for
maximum speed or response.
4b. Sample lines too long; filter 4b. Increase flow rate above 2000 cc/min.,
volumes too large, etc. for venting excess flow above 2000 cc/min. with
flow rate. a by-pass valve upstream of the analyzer.
4c. Measuring detector or cell 4c. Remove detectors and check for flow
block is dirty. between inlet and cell before remounting the
detectors.
5. Noisy output signal or 5a. Lack of earth ground 5a. Check that ground wire is connected to
electrical interference. ground terminal and that controller case is
connected to ground terminal.
5b. Power line not grounded 5b. Check that terminal L2/N is connected to the
correctly. neutral or grounded side of power line. If one
side of line is not grounded, install an isolation
transformer and ground terminal L2/N.
5c. Flow rate too high 5c. Check that flow does not exceed 2000
cc/min.***
5d. Cracked or dirty measuring 5d. Remove measuring detector, inspect for
detector. cracks in glass or loose dirt in cell.
5e. Faulty detector bridge-current 5e. Replace sensing-unit printed circuit card
regulator. assembly.****
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 71
Troubleshooting
6. Output signal is 6a. Temperature control is 6a. Check cell block for approximately 50 °C
unstable. inoperative. (122 °F) temperature (too hot to hold in the
hand for very long). Check heaters for 30
ohms nominal resistance for series pair.
Ambient temperature must not exceed 50 °C
(122 °F).
6b. Temperature control cycles. 6b. Check that temperature-sensing thermistor is
screwed tightly into the cell block and that its
tip and threads are coated with silicone
grease. Connect a 0 to 1 amp meter in series
with one of the heater leads. During warm-up,
current should be approximately 800 mA.
When 50 °C (122 °F) is reached current will
decrease, cycling 2 or 3 times before current
stabilizes at a lower value. If cycling
continues, replace the sensing unit circuit-
card assembly.****
6c. Sample flow rate or 6c. Check stability when operating on zero gas. If
composition varies. stable, check for large sample flow variations,
water vapor variations due to unstable drier or
cooler operation, etc.
7. Alarm malfunction. 7a. Alarm set point calibration is 7a. Adjust “Alarm 1” or “Alarm 2”. (See Section
inaccurate. 5.8.)
7b. Relay contacts worn or 7b. Replace circuit board if required.
damaged.
7c. Relay fails to energize (alarm 7c. Check alarm limits. (See Section 5.8.)
condition always indicated).
7d. Relay fails to de-energize 7d. This is normal while in Range 1 or 2. Check
(alarm condition never alarms limits while in Range 3.
indicated).
*For hydrogen spans greater than 10 %, current increase should be about 80 uA.
**For higher ranges minimum reading is proportionately higher, e.g., for 0 % to 30 % H2, reading should be 30 mV.
***On flowmeters calibrated for air, note that actual flow may exceed that indicated for H2 or other gases.
****Temperature regulator is a high-frequency variable-duty cycle controller and field repair is not recommended.
Replace the entire sensing-unit card and return the faulty unit to the factory for repairs.
72 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Troubleshooting
General
Verify that piping of analyzer and flow rates are correct. Verify that wiring of analyzer is correct.
Test for short circuit between leads of each of the above components and case ground.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 73
Troubleshooting
74 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Appendix A 7872 Gas Sampling Panel
9.1 Overview
This section contains information and drawings to be used with the 7872 Gas Sampling Panel is in use.
PARTS:
Description Part Number
Replacement Reference Air Regulator 51451417-501
Filter Cartridge for Reference Air Regulators 072927
Filter Cartridge for Sample Regulator 51500286-501
Replacement Sample Regulator Kit 51500283-501
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 75
Appendix A 7872 Gas Sampling Panel
9.3 Installation
1 See Figure 9-1 for mounting dimensions of the Gas Sampling Panel. Mount the Analyzer after
mounting the Gas Sampling Panel. The three stainless steel tubing connections made to the bottom
of the analyzer housing must not be overly tightened. The seal is made by an O-ring in each
analyzer fitting that grips the OD of the stainless steel tubing. If the fittings are too tight, O-ring
damage may occur.
2 All panel connections along the right side are 1/4 OD tube compression fittings. These connections
along the right side are 1/4 OD tube compression fittings. These connections can be tightened one
and one quarter turn to affect a seal upon installation of sample, calibration gas and vent-lines.
3 The bypass valve is included to prevent pressure build-up in the sensor housing. The bypass valve
is preset at 5 psig. During normal panel operation, the bypass valve remains closed and the bypass
flowmeter indicates no flow. If the bypass flowmeter indicates flow, check for clocked sample vent
and/or abnormally high pressure setting on sample regulator or calibration gases. (If the bypass
valve is to be replaced, note flow direction arrow stamped on valve body.)
4 The reference air regulator and sample regulator should be set at a pressure sufficient to allow
control of flow using the flowmeter valves (REF. AIR FLOW, CO2/AIR FLOW, H2 FLOW). The
flowmeter settings should be approximately 2 SCFH.
5 Before adjusting the Ref. Air Regulator or Sample Regulator, unlock the adjustment knob by
pulling up on the yellow lock ring. After adjustment is made, push down on the lock ring to
maintain the setting. For 7866 explosion-proof applications, set regulator pressure no higher
than 2 psig
The four-way selector valve is used to select from ZERO gas, SPAN gas or SAMPLE gas inlets.
The outlet of the four-way valve feeds into the three-way selector valve. The three-way valve is
used to direct the gas flow to either the CO2/AIR Flowmeter or the H2 Flowmeter. Whenever
sample or calibration gases contain a high content of H2, adjust the 3-way selector valve to direct
flow to the H2 flowmeter for accurate flow determination. This will avoid unnecessary
consumption of pure H2 gas.
76 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
9/06
30.125
(765.2 mm)
5.122
0.625 28.750 (130.1 mm)
Gas Analyzer to be mounted (15.87 mm) (730.3 mm)
as shown. Allow 12.875 (327 mm) 1.250 1.125
for cover and sensor removal. (31.75 mm) (28.58 mm)
0.687
(17.5 mm)
SKETCH “A-A”
Analyzer Bottom View
18 BYPASS VALVE REF A-Sample Inlet
(457.2 mm) AIR 5.219
30 B-Sample Outlet
IN (132.6 mm)
(762 mm) C-Ref Air In
CO2/AIR FLOW D-Ref Air Out
(Atmos. Press.)
ZERO GAS IN
3.763
(95.6 mm) Calibration Gases Required
SPAN GAS IN
for Triple Range Analyzer
SAMPLE
REGULATOR 4.870 Zero Gas:
H2 FLOW 100% Air: Range 1
(123.7 mm)
100% H2: Ranges 2 & 3
0.250 Dia. Span Gas:
(6.35 mm) SAMPLE 100% CO2: Ranges 1 & 2
Customer Connections (6)
GAS IN 75% H2 in N2: Range 3
Mounting 14” O.D. Tube Fittings
Holes (4)
Exhaust to
Sample Vent
7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance
Ref Air In
Zero Gas In 1 to 1000 psig
Span Gas In
Sample Gas In
Appendix A 7872 Gas Sampling Panel
77
Appendix A 7872 Gas Sampling Panel
SAMPLE VENT
5.5
(139.7 mm) REF AIR FLOW
A
"B" "C" "A" REF AIR REGULATOR
4
(101.6 mm)
BYPASS VALVE REF
3 A
AIR IN
(76.2) Section “A-A”
B B SPAN GAS IN
SAMPLE
H2 FLOW REGULATOR
Section “B-B”
Partial Side View
SAMPLE
GAS IN
9.4 Maintenance
Table 9-1 lists the replaceable parts for the Gas Sampling Panel. Refer to the exploded view in Figure 9-2.
78 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
Appendix B Security Bypass
10.1 Overview
Your controller has a security bypass code. Secured areas cannot be accessed without the use of the
Operator or Master codes. If you have forgotten or misplaced the access code, you can enter the factory
default code, “7866”. Use the procedure given in Table 5-8 to enter 7866 to override the forgotten code.
9/06 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 79
Appendix B Security Bypass
80 7866 Triple Range Digital H2 and CO2 Analyzer/Indicator - Operation and Maintenance 9/06
11. Sales and Service
For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor,
contact one of the offices below.
CANADA ITALY REPUBLIC OF SWITZERLAND
HONEYWELL LIMITED HONEYWELL S.p.A. SINGAPORE HONEYWELL A.G.
THE HONEYWELL Via P. Gobetti, 2/b HONEYWELL PTE LTD Hertistrasse 2
ARGENTINA CENTRE BLOCK 750E CHAI
20063 Cernusco Sul 8304 WALLISELLEN
HONEYWELL S.A.I.C. 300 Yorkland Blvd. CHEE ROAD
Naviglio SWITZERLAND
BELGRANO 1156 NORTH YORK, 06-01 CHAI CHEE IND.
ITALY Tel. : 41 1 831 02 71
BUENOS AIRES ONTARIO PARK
Tel. : 39 02 92146 1
ARGENTINA M2J 1S1 1646 SINGAPORE TURKEY
Tel. : 54 1 383 9290 CANADA REP. OF SINGAPORE
MEXICO HONEYWELL
Tel.: 800 461 0013 Tel. : 65 2490 100
HONEYWELL S.A. DE Otomasyon ve Kontrol
ASIA PACIFIC Fax:: 416 502 5001
CV Sistemlen San ve Tic
HONEYWELL ASIA REPUBLIC OF SOUTH
AV. CONSTITUYENTES A.S.
PACIFIC Inc. CZECH AFRICA
900 (Honeywell Turkey A.S.)
Room 3213-3225 REPUBLIC HONEYWELL
COL. LOMAS ALTAS Emirhan Cad No 144
Sun Kung Kai Centre HONEYWELL, Spol.s.r.o. Southern Africa
11950 MEXICO CITY Barbaros Plaza C. Blok
N° 30 Harbour Road Budejovicka 1 PO BOX 138
MEXICO Kat 18
WANCHAI 140 21 Prague 4 Milnerton 7435
Tel : 52 5 259 1966 Dikilitas 80700 Istanbul
HONG KONG Czech Republic REPUBLIC OF SOUTH
TURKEY
Tel. : 852 829 82 98 Tel. : 42 2 6112 3434 AFRICA
THE NETHERLANDS Tel : 90-212 258 18 30
Tel. : 27 11 805 12 01
HONEYWELL BV
AUSTRALIA DENMARK
Laaderhoogtweg 18 UNITED KINGDOM
HONEYWELL LIMITED HONEYWELL A/S ROMANIA
1101 EA AMSTERDAM HONEYWELL
5 Thomas Holt Drive Automatikvej 1 HONEYWELL Office
ZO Unit 1,2 &4 Zodiac House
North Ryde Sydney DK 2860 Soeborg Bucharest
THE NETHERLANDS Calleva Park
NSW AUSTRALIA 2113 DENMARK 147 Aurel Vlaicu Str.,
Tel : 31 20 56 56 911 Aldermaston
Tel. : 61 2 353 7000 Tel. : 45 39 55 56 58 Sc.Z.,
Berkshire RG7 8HW
AUSTRIA Apt 61/62
NORWAY UNITED KINGDOM
FINLAND R-72921 Bucharest
HONEYWELL A/S Tel : 44 118 906 2600
HONEYWELL AUSTRIA HONEYWELL OY ROMANIA
Askerveien 61
G.m.b.H. Ruukintie 8 Tel : 40-1 211 00 76/
PO Box 263 U.S.A.
Handelskai 388 FIN-02320 ESPOO 32 211 79
N-1371 ASKER HONEYWELL INC.
A1020 VIENNA FINLAND
NORWAY INDUSTRIAL PROCESS
AUSTRIA Tel. : 358 0 3480101 RUSSIA CONTROLS
Tel. : 47 66 76 20 00
Tel. : 43 1 727 800 HONEYWELL INC 1100 VIRGINIA DRIVE
FRANCE 4 th Floor Administrative PA 19034-3260
POLAND
BELGIUM HONEYWELL S.A. Builiding of AO "Luzhniki" FT. WASHINGTON
HONEYWELL Sp.z.o.o
HONEYWELL S.A. Bâtiment « le Mercury » Management U.S.A.
UI Domainewksa 41
3 Avenue de Bourget Parc Technologique de St 24 Luzhniki Tel. : 1-800-343-0228
02-672 WARSAW
B-1140 BRUSSELS Aubin 119048 Moscow
POLAND
BELGIUM Route de l’Orme RUSSIA VENEZUELA
Tel. : 48 22 606 09 00
Tel. : 32 2 728 27 11 (CD 128) Tel : 7 095 796 98 00/01 HONEYWELL CA
91190 SAINT-AUBIN APARTADO 61314
PORTUGAL
BRAZIL FRANCE SLOVAKIA 1060 CARACAS
HONEYWELL
HONEYWELL DO Tel. from France: HONEYWELL Ltd VENEZUELA
BRAZIL PORTUGAL LDA
01 60 19 80 00 Mlynske nivy 73 Tel. : 58 2 239 0211
AND CIA Edificio Suecia II
From other countries: PO Box 75
Rua Jose Alves Da Av. do Forte nr 3 - Piso 3
33 1 60 19 80 00 820 07 BRATISLAVA 27
Chunha 2795 CARNAXIDE
SLOVAKIA
Lima 172 PORTUGAL
GERMANY Tel. : 421 7 52 47 400/
BUTANTA Tel. : 351 1 424 50 00
HONEYWELL AG 425
05360.050 SAO PAULO Kaiserleistrasse 39
SP REPUBLIC OF IRELAND
D-63067 OFFENBACH SPAIN
BRAZIL HONEYWELL
GERMANY HONEYWELL S.A
Tel. : 55 11 819 3755 Unit 1
Tel. : 49 69 80 64444 Factory
Robinhood Business
Josefa Valcarcel, 24
BULGARIA Park
HUNGARY 28027 MADRID
HONEYWELL EOOD Robinhood Road
HONEYWELL Kft SPAIN
14, Iskarsko Chausse DUBLIN 22
Gogol u 13 Tel. : 34 91 31 3 61 00
POB 79 Republic of Ireland
H-1133 BUDAPEST
BG- 1592 Sofia Tel. : 353 1 4565944
HUNGARY SWEDEN
BULGARIA Tel. : 36 1 451 43 00 HONEYWELL A.B.
Tel : 359-791512/ S-127 86 Skarholmen
794027/ 792198 ICELAND STOCKHOLM
HONEYWELL SWEDEN
Hataekni .hf Tel. : 46 8 775 55 00
Armuli 26
PO Box 8336
128 reykjavik
Iceland
Tel : 354 588 5000
Industrial Measurement and Control
Honeywell
1100 Virginia Drive
Fort Washington, PA 19034