Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
INPUT DATA
Mx at other end = M 2 := 10 kN m
Tors. mod. = G := 80000 mPa
Slend Factor = k := 1.0
S.M.Y.S. = Fy := 355 mPa Fyimp := 50
Area of section - A := [ ( 2 b T) + [ ( d 2 T) t 2 ] ]
T3 d T
2
( d 2 T)
3
Moment of Inertia - Ix := 2 b + b T + 2 t
12 2 2 12
b3 3 2
Iy := 2 T + 2 ( d 2 T) t + ( d 2 T) t b t
12 12 2 2
Ix Iy
Section modulii - zx := 2 zy := 2
d b
Ix Iy
Radii of gyration - rx := ry :=
A A
1 1 of ??
2 2
2 T t ( d T) ( b t )
TORSION RESISTANCE K := 4
2 2 K = 3190 cm
d T + b t T t
not necessary for stress,
only for input into QSE
ACTUAL STRESSES
Mx
Major axis bending - fbx := fbx = 108 mPa
zx
My
Minor axis bending - fby := fby = 18 mPa
zy
F
Tensile stress - fa := fa = 6 mPa
A
S
Shear stress - fq := fq = 5 mPa
d t
Tors
Torsional stress - := = 9 mPa
2 T ( d T) ( b t )
ALLOWABLE STRESSES
TENSILE STRESS
Section D1; the allowable tensile stress of
members is detailed herein:- Fa := 0.6 Fy
SHEAR STRESS
Section F4; the allowable shear stress - Fq := 0.4 Fy
BENDING STRESSES
F3.1 Members with Compact Sections
For members bent about their strong or weak Fbx1 := 0.66 Fy Fby := 0.66 Fy
axes, members with compact sections as defined
in Sect B5, the allowable bending stress is
defined as
2 2 of ??
The adjacent conditional equations direct Fbx3 := if ( d < 6 b , Fbx1 , Fbx2)
towards the correct stress for the governing
geometric conditions
Fbx4 := if ( T < 2 t , Fbx3 , Fbx2)
Mx
1950 + 1200 M b
2 , F , F
Fbx := if Ly <
bx4 bx2
Fyimp
Fyimp
Combined Stress
Section H2; for members subject to both axial tension fa fbx fby
and bending, the following equations shall equal less + + = 0.57
Fa Fbx Fby
than 1.0
fa fbx fby
if + + < 1.0 , "Beam OK" , "Beam Not OK" = "Beam OK"
Fa Fbx Fby
Equivalent Stress
This stress check is not required by AISC, but is commonly
performed. It is a requirement of other standards, for example
BS449 which requires a limit of 0.92 x SMYS
fe
fe := (fa + fbx + fby)2 + 3 ( fq + )2 0.92 Fy
= 0.41
fe
if < 1.0 , "Beam OK" , "Beam Not OK" = "Beam OK"
0.92 Fy
End of Section
3 3 of ??
N newton
kN 1000 N
mPa 1000000Pa
4 4 of ??