Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
7KH/HDGHUVKLSLQ(QHUJ\DQG
(QYLURQPHQWDO'HVLJQ/((' ) Green
%XLOGLQJ5DWLQJV\VWHPTM is the nationally
accepted benchmark for the design,
construction and operation of high
performance green buildings.
60 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
1 Minimum values obtained as a result of three cure temperatures (23, 40, 60F)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 61
Adhesive Anchoring Systems
3.2.3.3 Strength Add ACI 318 Section D.4.1.4 as follows: 3.2.3.3.2. Static Steel Strength in
Design1,2 Tension: The nominal static steel
D.4.1.4 For adhesive anchors
strength of a single anchor in tension,
3.2.3.3.1 General: Design strengths VXEMHFWHGWRWHQVLRQUHVXOWLQJIURP
Nsa, in accordance with ACI 318 D.5.1.2
are determined in accordance with sustained loading, a supplementary
and strength reduction factor, , in
ACI 318-08 Appendix D (ACI 318) and FKHFNVKDOOEHSHUIRUPHGXVLQJ(T'
accordance with ACI D.4.4 are given in
VXSSOHPHQWHGE\,&&(6(65 whereby Nua is determined from the
the tables outlined in Table 1a for the
sustained load alone, e.g., the dead load
Design parameters are provided in Table corresponding anchor steel.
5 through Table 19. Strength reduction and that portion of the live load acting
3.2.3.3.3. Static Concrete Breakout
factors, , as given in ACI 318 D.4.4 that may be considered as sustained and
Strength in Tension: The nominal static
must be used for load combinations Nn is determined as follows:
calculated in accordance with Section concrete breakout strength of a single
D.4.1.4.1 For single anchors,
RIWKH,%&DQG6HFWLRQRI anchor or group of anchors in tension,
Nn = 0.75Na0.
ACI 318. Strength reduction factors, , Ncb or Ncbg, must be calculated in
as given in ACI 318 D.4.5 must be used D.4.1.4.2 For anchor groups, accordance with ACI 318 D.5.2 with the
for load combinations calculated in (T'VKDOOEHVDWLVILHGE\WDNLQJ following addition:
accordance with ACI 318 Appendix C. Nn = 0.75fNa0 for that anchor in an
',%&RU'
anchor group that resists the highest
The following amendments to ACI 318 ,%&7KHOLPLWLQJFRQFUHWHVWUHQJWK
tension load.
$SSHQGL['PXVWEHXVHGDVUHTXLUHGIRU of adhesive anchors in tension shall be
the strength design of adhesive anchors. D.4.1.4.3 Where shear loads act calculated in accordance with D.5.2.1 to
,QFRQIRUPDQFHZLWK$&,DOOHTXDWLRQV concurrently with the sustained tension 'XQGHUWKH,%&RU'WR
are expressed in inch-pound units. load, the interaction of tension and 'XQGHUWKH,%&ZKHUHWKH
shear shall be analyzed in accordance value of kcWREHXVHGLQ(T'
Modify ACI 318 D.4.1.2 as follows: with D.4.1.3. shall be:
D.4.1.2 ,Q(T'DQG'Nn Modify ACI 318 D.4.2.2 in accordance kc,cr where analysis indicates cracking at
and Vn are the lowest design strengths ZLWK,%&6HFWLRQDV service load levels in the anchor vicinity
determined from all appropriate failure follows: (cracked concrete). The values of kc,cr
modes. Nn is the lowest design are given in Tables 6, 9, 12, 15 and 18
strength in tension of an anchor or D.4.2.2 The concrete breakout
of this document.
group of anchors as determined from VWUHQJWKUHTXLUHPHQWVIRUDQFKRUVLQ
consideration of Nsa, either Na or tension shall be considered satisfied kc,uncr where analysis indicates no
Nag and either Ncb or Ncbg. Vn is by the design procedure of D.5.2 cracking at service load levels in the
the lowest design strength in shear of SURYLGHG(TXDWLRQ'LVQRWXVHGIRU anchor vicinity (uncracked concrete).
an anchor or a group of anchors as anchor embedments exceeding 25 The values of kc,uncr are given in Tables
determined from consideration of: Vsa, inches. The concrete breakout strength 6, 9, 12, 15 and 18 of this document.
either Vcb or Vcbg, and either Vcp or UHTXLUHPHQWVIRUDQFKRUVLQVKHDUZLWK
The basic concrete breakout strength
Vcpg)RUDGKHVLYHDQFKRUVVXEMHFWHG diameters not exceeding 2 inches
of a single anchor in tension, Nb, must
to tension resulting from sustained shall be considered satisfied by the
be calculated in accordance with ACI
loading, refer to D.4.1.4 for additional design procedure of D.6.2. For anchors
D.5.2.2 using values of hef' kc,cr and
UHTXLUHPHQWV in shear with diameters exceeding 2
kc,uncr as decribed in the tables of this
inches, shear anchor reinforcement shall
GRFXPHQW7KHPRGLILFDWLRQIDFWRU
be provided in accordance with the
shall be taken as 1.0. Anchors shall not
procedures of D.6.2.9.
be installed in lightweight concrete.
The value of 'c used for calculation
must be limited to 8,000 psi (55 MPa) in
accordance with ACI 318 D.3.5.
1 ACI 318-05 or 318-02 may also be used. The section references and terminology are different from those given in this section.
7KLVVHFWLRQLVDUHSURGXFWLRQRIWKHFRQWHQWRI,&&65UHSUHVHQWLQJWKHRSLQLRQVDQGUHFRPPHQGDWLRQVRI,&&(6
62 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
[( ) ]
0.5
s
____ a group of adhesive anchors is located
g,Na= g,Na0 + (1-g,Na0 ) (D-16g)
scr,Na in a region of a concrete member where
ANa
Nag = ___ ed,Nag,Naec,Nap,Na1a0 analysis indicates no cracking at service
ANa0 Where
(D-16b) load levels, the nominal strength, Na
ok,cr 1.5
where:
ANaLVWKHSURMHFWHGDUHDRIWKHIDLOXUH
[
g,Na0 = n ( n 1)
( ok,max,cr ) ]
1.0 or Nag, of a single adhesive anchor or
a group of adhesive anchors shall be
surface for the single anchor or group of (D16h) FDOFXODWHGDFFRUGLQJWR(T'DDQG
anchors that shall be approximated as the Where (T'EZLWKok,uncr substituted for ok,cr
base of the rectilinear geometrical figure n = the number of tension-loaded in the calculation of the basic strength
WKDWUHVXOWVIURPSURMHFWLQJWKHIDLOXUH adhesive anchors in a group. NaoLQDFFRUGDQFHZLWK(T'I
surface outward a distance, ccr,Na, from the The factor g,Na0 shall be calculated in
kc,cr
centerline of the anchor, or in the case of ok,max,cr = hef 'c (D-16i) DFFRUGDQFHZLWK(T'KZKHUHE\
d the value of k,max,uncr shall be calculated
a group of anchors, from a line through
DURZRIDGMDFHQWDQFKRUV$Na shall not The value of 'c must be limited to a LQDFFRUGDQFHZLWK(T'QDQG
exceed nANa0 where n is the number of maximum of 8,000 psi (55 MPa) in substituted for ok,max,crLQ(T'K
anchors in tension in the group. In ACI accordance with ACI 318 D.3.5.
ok,uncr
318 Figures RD.5.2.1a and RD.5.2.1b, the ok,max,uncr = ______ hef 'c (D-16n)
D.5.3.11 The modification factor for /d
terms 1.5hef and 3.0hef shall be replaced
eccentrically loaded adhesive anchor D.5.3.14When an adhesive anchor or
with ccr,Na and scr,Na, respectively.
groups is: a group of adhesive anchors is located
ANa0LVWKHSURMHFWHGDUHDRIWKHIDLOXUH in a region of a concrete member where
1
surface of a single anchor without ec,Na = _________ 'M analysis indicates no cracking at service
2e'n
1 + _____
the influence of proximate edges in load levels, the modification factor p,Na
scr,Na
DFFRUGDQFHZLWK(T'F shall be taken as:
s
ANa0 = (scr,Na)2 (D-16c) (T'MLVYDOLGIRUH'N ___ p,Na = 1.0 when ca,min cac (D-16o)
2
with
If the loading on an anchor group is max | ca,min ccr,Na | when c
p,Na = ________________ < cac
a,min
scr,Na DVJLYHQE\(T'G such that only certain anchors are in cac
(D-16p)
D.5.3.8 The critical spacing scr,Na tension, only those anchors that are where:
and critical edge distance ccr,Na shall be in tension shall be considered when
cac shall be determined in accordance
calculated as follows: determining the eccentricity e'N for use
with Section 3.2.3.3.10 of this
LQ(T'M
document.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 63
Adhesive Anchoring Systems
ai
Reduction
Concrete
Strength
Strength
%RQG
Factor
,%&DQGG0,%&,QDGGLWLRQ cai < 5 x d sai 16 in. (406 mm) 0.5 x Tmax
Dry ok,uncr d
For the calculation of Ncb, Ncbg, Na and
be limited to a maximum of 8,000 psi (55
Water- Nag in accordance with ACI 318 Section
MPa) in accordance with ACI 318 D.3.5. ok,uncr ws
saturated D.5.2.7 and Section 3.2.3.3.4 of this
3.2.3.3.7. Static Concrete Pryout document, the critical edge distance,
Dry ok,cr d
Cracked
64 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 65
Adhesive Anchoring Systems
7PD[
V
$OO7KUHDG
RUUHEDU
G
KHI
GR
Cracked/Un-Cracked Concrete
Hammer Drilled
FD FWS
(D) (WS)
ok,uncr or ok,cr
66 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
) R U 6, OE N 1 S V
L
D
3
0
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 67
Adhesive Anchoring Systems
Minimum Minimum
Minimum
Specified Specified Yield Minimum
Reduction
Threaded Rod Specification Ultimate Strength 0.2% uta ya (ORQJDWLRQ Specification for Nuts6
of Area,
Strength Offset Percent5
Percent
uta ya
ASTM A 1932*UDGH% psi 125,000 105,000
1.19 16 50 ASTM A194
LQPP (MPa) (860) (725)
ASTM F 568M3 Class 5.8
MPa 500 400 DIN 934 (8-A2K)
0LQWR0LQ 1.25 10 35
(psi) (72,500) (58,000) ASTM A563 Grade DH7
HTXLYDOHQWWR,62
MPa 500 400
ISO 898-14 Class 5.8 1.25 22 - DIN 934 (Grade 6)
(psi) (72,500) (58,000)
MPa 800 640
ISO 898-14 Class 8.8 1.25 12 52 DIN 934 (Grade 8)
(psi) (116,000) (92,800)
+LOWL+,7+<0$;6'DGKHVLYHPD\EHXVHGLQFRQMXQFWLRQZLWKDOOJUDGHVRIFRQWLQXRXVO\WKUHDGHGFDUERQVWHHOURGDOOWKUHDGWKDW
FRPSO\ZLWKWKHFRGHUHIHUHQFHVWDQGDUGVDQGWKDWKDYHWKUHDGFKDUDFWHULVWLFVFRPSDUDEOHZLWK$16,%81&&RDUVH7KUHDG6HULHVRU
$16,%003URILOH0HWULF7KUHDG6HULHV9DOXHVIRUWKUHDGHGURGW\SHVDQGDVVRFLDWHGQXWVVXSSOLHGE\+LOWLDUHSURYLGHGKHUH
6WDQGDUG6SHFLILFDWLRQIRU$OOR\6WHHODQG6WDLQOHVV6WHHO%ROWLQJ0DWHULDOVIRU+LJK7HPSHUDWXUH6HUYLFH
6WDQGDUG6SHFLILFDWLRQIRU&DUERQDQG$OOR\6WHHO([WHUQDOO\7KUHDGHG0HWULF)DVWHQHUV
0HFKDQLFDOSURSHUWLHVRIIDVWHQHUVPDGHRIFDUERQVWHHODQGDOOR\VWHHO3DUW%ROWVVFUHZVDQGVWXGV
%DVHGRQLQPPJDXJHOHQJWKH[FHSW$670$ZKLFKDUHEDVHGRQDJDXJHOHQJWKRIGDQG,62ZKLFKLVEDVHGRQG
6 Nuts of other grades and styles having specified proof load stresses greater than the specified grade and style are also suitable. Nuts must
KDYHVSHFLILHGSURRIORDGVWUHVVHVHTXDOWRRUJUHDWHUWKDQWKHPLQLPXPWHQVLOHVWUHQJWKRIWKHVSHFLILHGWKUHDGHGURG
7 Nuts for fractional rods.
Minimum Minimum
Minimum
Specified Specified Yield Minimum
Reduction
Threaded Rod Specification Ultimate Strength 0.2% uta ya (ORQJDWLRQ Specification for Nuts4
of Area,
Strength Offset Percent5
Percent
uta ya
ASTM F 5932 CW1 (316) psi 100,000 65,000
1.54 20 - F 594
WRLQ (MPa) (690) (450)
2
ASTM F 593 CW2 (316) psi 85,000 45,000
1.89 25 - F 594
WRLQ (MPa) (585) (310)
ISO 3506-13 A4-70 MPa 700 450
1.56 40 - ISO 4032
M8 M24 (psi) (101,500) (65,250)
+LOWL+,7+<0$;6'PD\EHXVHGLQFRQMXQFWLRQZLWKDOOJUDGHVRIFRQWLQXRXVO\WKUHDGHGVWDLQOHVVVWHHOURGDOOWKUHDGWKDWFRPSO\ZLWK
WKHFRGHUHIHUHQFHVWDQGDUGVDQGWKDWKDYHWKUHDGFKDUDFWHULVWLFVFRPSDUDEOHZLWK$16,%81&&RDUVH7KUHDG6HULHVRU
$16,%003URILOH0HWULF7KUHDG6HULHV9DOXHVIRUWKUHDGHGURGW\SHVDQGDVVRFLDWHGQXWVVXSSOLHGE\+LOWLDUHSURYLGHGKHUH
6WDQGDUG6WHHO6SHFLILFDWLRQIRU6WDLQOHVV6WHHO%ROWV+H[&DS6FUHZVDQG6WXGV
0HFKDQLFDOSURSHUWLHVRIFRUURVLRQUHVLVWDQWVWDLQOHVVVWHHOIDVWHQHUV3DUW%ROWVVFUHZVDQGVWXGV
4 Nuts of other grades and styles having specified proof load stresses greater than the specified grade and style are also suitable. Nuts must
KDYHVSHFLILHGSURRIORDGVWUHVVHVHTXDOWRRUJUHDWHUWKDQWKHPLQLPXPWHQVLOHVWUHQJWKRIWKHVSHFLILHGWKUHDGHGURG
68 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 69
Adhesive Anchoring Systems
70 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
)RULQVWDOODWLRQVZLWKDLQHGJHGLVWDQFHWKHLQVWDOODWLRQWRUTXHPXVWEHUHGXFHG3OHDVHUHIHUWRVHFWLRQ
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 71
Adhesive Anchoring Systems
Characteristic bond strength psi 1,610 1,610 1,495 1,385 1,275 1,170
ok,uncr
in uncracked concrete (MPa) (11.1) (11.1) (10.3) (9.6) (8.8) (8.1)
%
Characteristic bond strength psi 561 615 662 711 717 723
ok,cr
in cracked concrete3 (MPa) (3.9) (4.2) (4.6) (4.9) (4.9) (5.0)
Characteristic bond strength psi 930 930 865 805 740 675
ok,uncr
in uncracked concrete (MPa) (6.4) (6.4) (6.0) (5.5) (5.1) (4.7)
C
Characteristic bond strength psi 321 352 379 407 410 414
ok,cr
in cracked concrete3 (MPa) (2.2) (2.4) (2.6) (2.8) (2.8) (2.9)
Minimum anchor embedment depth in. 4
hef,min
(mm) (60) (70) (79) (89) (89) (102)
Maximum anchor embedment depth in. 10 15 20
hef,max
(mm) (191) (254) (318) (381) (445) (508)
Anchor
Permissible
installation
conditions
- 1
Dry concrete and Water-saturated Category
concrete
d & ws 0.65
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897 MPa.
For pound-inch units: 1 mm = 0.03937 inches, 1 N = 0.2248 lbf, 1 MPa = 145.0 psi.
%RQGVWUHQJWKYDOXHVFRUUHVSRQGWRFRQFUHWHFRPSUHVVLYHVWUHQJWKUDQJHSVL'cSVL)RUSVL'cSVL
tabulated characteristic bond strengths may be increased by 6 percent. For 6,500 psi < 'cSVLWDEXODWHGFKDUDFWHULVWLFERQG
strengths may be increased by 10 percent.
2 Temperature range A: Maximum short term temperature = 104F (40C), maximum long term temperature = 75F (24C).
7HPSHUDWXUHUDQJH%0D[LPXPVKRUWWHUPWHPSHUDWXUH )&PD[LPXPORQJWHUPWHPSHUDWXUH )&
Temperature range C: Maximum short term temperature = 248F (120C), maximum long term temperature = 162F (72C).
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete
temperatures are roughly constant over significant periods of time.
)RUVWUXFWXUHVDVVLJQHGWR6HLVPLF'HVLJQ&DWHJRULHV&'(RU)ERQGVWUHQJWKYDOXHVDUHPXOWLSOLHGE\N,seis = 1.0 => no reduction.
72 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
Vsa
(lbf) (5,215) (9,100) (16,940) (26,440) (38,090)
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897 MPa.
For pound-inch units: 1 mm = 0.03937 inches, 1 N = 0.2248 lbf, 1 MPa = 145.0 psi.
9DOXHVSURYLGHGIRUFRPPRQURGPDWHULDOW\SHVEDVHGRQSXEOLVKHGVWUHQJWKVDQGFDOFXODWHGLQDFFRUGDQFHZLWK$&,(T'DQG(T
'2WKHUPDWHULDOVSHFLILFDWLRQVDUHDGPLVVLEOHVXEMHFWWRWKHDSSURYDORIWKHFRGHRIILFLDO1XWVDQGZDVKHUVPXVWEHDSSURSULDWHIRU
the rod strength.
)RUXVHZLWKWKHORDGFRPELQDWLRQVRI,%&6HFWLRQRU$&,6HFWLRQDVVHWIRUWKLQ$&,',IWKHORDGFRPELQDWLRQV
of ACI 318 Appendix C are used, the appropriate value of f must be determined in accordance with ACI 318 D.4.5. Values correspond to a
brittle steel element.
3 A4-70 Stainless (M10 - M24 diameters)
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 73
Adhesive Anchoring Systems
74 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
- 1
installation
conditions
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete
temperatures are roughly constant over significant periods of time.
)RUVWUXFWXUHVDVVLJQHGWR6HLVPLF'HVLJQ&DWHJRULHV&'(RU)ERQGVWUHQJWKYDOXHVDUHPXOWLSOLHGE\N,seis = 1.0 => no reduction.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 75
Adhesive Anchoring Systems
%DU6L]H
Design Information Symbol Units
No. 3 No. 4 No. 5 No. 6 No. 7 No. 8
in. 1
Nominal bar diameter d
(mm) (9.5) (12.7) (15.9) (19.1) (22.2) (25.4)
in.2 0.11 0.2 0.31 0.44 0.6 0.79
%DUHIIHFWLYHFURVVVHFWLRQDODUHD Ase 2
(mm ) (71) (129) (200) (284) (387) (510)
lb 6,600 12,000 18,600 26,400 36,000 47,400
Nsa
Nominal strength as governed (kN) (29.4) (53.4) (82.7) (117.4) (160.1) (210.9)
ASTM A 615 Gr. 40
76 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
%DU6L]H
Design Information Symbol Units
No. 3 No. 4 No. 5 No. 6 No. 7 No. 8
in-lb 24 24 24 24 24 24
(IIHFWLYHQHVVIDFWRUIRUXQFUDFNHGFRQFUHWH kc,uncr
(SI) (10) (10) (10) (10) (10) (10)
in-lb 17 17 17 17 17 17
(IIHFWLYHQHVVIDFWRUIRUFUDFNHGFRQFUHWH kc,cr
(SI) (7) (7) (7) (7) (7) (7)
in. 5
Minimum bar spacing4 smin
(mm) (48) (64) (79) (95) (111) (127)
in. 5
Minimum edge distance4 cmin
(mm) (48) (64) (79) (95) (111) (127)
in. hef
Minimum member thickness hmin hef + 2d0(3)
(mm) (hef + 30)
Critical edge distance splitting
cac - See Section 3.2.3.3.10 of this document.
(for uncracked concrete)
Strength reduction factor for tension,
- 0.65
FRQFUHWHIDLOXUHPRGHV&RQGLWLRQ%2
Strength reduction factor for shear,
- 0.70
FRQFUHWHIDLOXUHPRGHV&RQGLWLRQ%2
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897MPa.
For pound-inch units: 1 mm = 0.03937 inches, 1 N = 0.2248 lbf, 1 MPa = 145.0 psi.
1 For additional setting information, see installation instructions in Figure 5.
9DOXHVSURYLGHGIRUSRVWLQVWDOOHGDQFKRUVZLWKFDWHJRU\DVGHWHUPLQHGIURP$&,JLYHQIRU&RQGLWLRQ%&RQGLWLRQ%DSSOLHVZLWKRXW
VXSSOHPHQWDU\UHLQIRUFHPHQWRUZKHUHSXOORXWERQGRUSU\RXWJRYHUQDVVHWIRUWKLQ$&,'ZKLOHFRQGLWLRQ$UHTXLUHVVXSSOHPHQWDO
UHLQIRUFHPHQW9DOXHVDUHIRUXVHZLWKWKHORDGFRPELQDWLRQVRI,%&6HFWLRQRU$&,6HFWLRQDVVHWIRUWKLQ$&,',I
the load combinations of ACI 318 Appendix C are used, the appropriate value of f must be determined in accordance with ACI 318 D.4.5.
3 d0 = drill bit diameter.
)RULQVWDOODWLRQVZLWKDLQHGJHGLVWDQFHWKHLQVWDOODWLRQWRUTXHPXVWEHUHGXFHG3OHDVHUHIHUWRVHFWLRQ
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 77
Adhesive Anchoring Systems
%DU6L]H
Design Information Symbol Units
No. 3 No. 4 No. 5 No. 6 No. 7 No. 8
Characteristic bond strength psi 1,290
ok,uncr
in uncracked concrete MPa (8.9)
A
Characteristic bond strength psi 696 763 821 881 889 896
ok,cr
in cracked concrete3 MPa (4.8) (5.3) (5.7) (6.1) (6.1) (6.2)
Temperature range2
- 1
Dry concrete and Water-saturated Category
concrete
dfws 0.65
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete
temperatures are roughly constant over significant periods of time.
)RUVWUXFWXUHVDVVLJQHGWR6HLVPLF'HVLJQ&DWHJRULHV&'(RU)ERQGVWUHQJWKYDOXHVDUHPXOWLSOLHGE\N,seis = 1.0 => no reduction.
78 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
%DU6L]H
Design Information Symbol Units
10 12 14 16 20 25
mm 10.0 12.0 14.0 16.0 20.0 25.0
Nominal bar diameter d
(in.) (0.394) (0.472) (0.551) (0.630) (0.787) (0.984)
mm2 78.5 113.1 153.9 201.1 314.2 490.9
%DUHIIHFWLYHFURVVVHFWLRQDODUHD Ase 2
(in. ) (0.122) (0.175) (0.239) (0.312) (0.487) (0.761)
kN 43.2 62.2 84.7 110.6 172.8 270.0
Nsa
(lb) (9,710) (13,985) (19,035) (24,860) (38,845) (60,695)
',1%6W
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 79
Adhesive Anchoring Systems
%DUVL]H
Design Information Symbol Units
10 12 14 16 20 25
SI 10 12.6
(IIHFWLYHQHVVIDFWRUIRUXQFUDFNHGFRQFUHWH kc,uncr
(in-lb) (24) (30)
SI 7
(IIHFWLYHQHVVIDFWRUIRUFUDFNHGFRQFUHWH kc,cr
(in-lb) (17)
mm 50 60 70 80 100 125
Minimum bar spacing4 smin
(in.) (2) (2.4) (2.8) (3.1) (3.9) (4.9)
mm 50 60 70 80 100 125
Minimum edge distance4 cmin
(in.) (2) (2.4) (2.8) (3.1) (3.9) (4.9)
mm hef + 30
Minimum member thickness hmin hef + 2d0(3)
(in.) (hef
Critical edge distance splitting
cac - See Section 3.2.3.3.10 of this document.
(for uncracked concrete)
Strength reduction factor for tension,
- 0.65
FRQFUHWHIDLOXUHPRGHV&RQGLWLRQ%2
Strength reduction factor for shear,
- 0.70
FRQFUHWHIDLOXUHPRGHV&RQGLWLRQ%2
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897MPa.
For pound-inch units: 1 mm = 0.03937 inches, 1 N = 0.2248 lbf, 1 MPa = 145.0 psi.
1 For additional setting information, see installation instructions in Figure 5.
9DOXHVSURYLGHGIRUSRVWLQVWDOOHGDQFKRUVZLWKFDWHJRU\DVGHWHUPLQHGIURP$&,JLYHQIRU&RQGLWLRQ%&RQGLWLRQ%DSSOLHVZLWKRXW
VXSSOHPHQWDU\UHLQIRUFHPHQWRUZKHUHSXOORXWERQGRUSU\RXWJRYHUQDVVHWIRUWKLQ$&,'ZKLOHFRQGLWLRQ$UHTXLUHVVXSSOHPHQWDO
UHLQIRUFHPHQW9DOXHVDUHIRUXVHZLWKWKHORDGFRPELQDWLRQVRI,%&6HFWLRQRU$&,6HFWLRQDVVHWIRUWKLQ$&,'
If the load combinations of ACI 318 Appendix C are used, the appropriate value of f must be determined in accordance with ACI 318 D.4.5.
3 d0 = drill bit diameter.
)RULQVWDOODWLRQVZLWKDLQHGJHGLVWDQFHWKHLQVWDOODWLRQWRUTXHPXVWEHUHGXFHG3OHDVHUHIHUWRVHFWLRQ
80 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
%DU6L]H
Design Information Symbol Units
10 12 14 16 20 25
Characteristic bond strength MPa 8.9
ok,uncr
in uncracked concrete (psi) (1,290)
A
Characteristic bond strength MPa 4.9 5.1 5.4 5.7 6.1 6.1
ok,cr
in cracked concrete3 (psi) (705) (744) (783) (822) (884) (895)
Temperature range2
- 1
Dry concrete and Category
Water-saturated concrete
d & ws - 0.65
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete
temperatures are roughly constant over significant periods of time.
)RUVWUXFWXUHVDVVLJQHGWR6HLVPLF'HVLJQ&DWHJRULHV&'(RU)ERQGVWUHQJWKYDOXHVDUHPXOWLSOLHGE\N,seis = 1.0 => no reduction.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 81
Adhesive Anchoring Systems
Table 18 Concrete Breakout Design Information for Canadian Metric Reinforcing Bars1 c
%DUVL]H
Design Information Symbol Units
10 M 15 M 20 M 25 M
SI 10 10 10 11.3
(IIHFWLYHQHVVIDFWRUIRUXQFUDFNHGFRQFUHWH kc,uncr
(in-lb) (24) (24) (24) (27)
SI 7 7 7 7
(IIHFWLYHQHVVIDFWRUIRUFUDFNHGFRQFUHWH kc,cr
(in-lb) (17) (17) (17) (17)
mm 57 80 98 126
Minimum bar spacing4 smin
(in.) (2.2) (3.1) (3.8) (5.0)
mm 57 80 98 126
Minimum edge distance4 cmin
(in.) (2.2) (3.1) (3.8) (5.0)
mm hef + 30
Minimum member thickness hmin hef + 2d0(3)
(in.) (hef
Critical edge distance splitting
cac - See Section 3.2.3.3.10 of this document.
(for uncracked concrete)
Strength reduction factor for tension,
- 0.65
FRQFUHWHIDLOXUHPRGHV&RQGLWLRQ%2
Strength reduction factor for shear,
- 0.70
FRQFUHWHIDLOXUHPRGHV&RQGLWLRQ%2
For SI: 1 inch = 25.4 mm, 1 lbf = 4.448 N, 1 psi = 0.006897MPa.
For pound-inch units: 1 mm = 0.03937 inches, 1 N = 0.2248 lbf, 1 MPa = 145.0 psi.
1 For additional setting information, see installation instructions in Figure 5.
9DOXHVSURYLGHGIRUSRVWLQVWDOOHGDQFKRUVZLWKFDWHJRU\DVGHWHUPLQHGIURP$&,JLYHQIRU&RQGLWLRQ%&RQGLWLRQ%DSSOLHVZLWKRXW
VXSSOHPHQWDU\UHLQIRUFHPHQWRUZKHUHSXOORXWERQGRUSU\RXWJRYHUQDVVHWIRUWKLQ$&,'ZKLOHFRQGLWLRQ$UHTXLUHVVXSSOHPHQWDO
UHLQIRUFHPHQW9DOXHVDUHIRUXVHZLWKWKHORDGFRPELQDWLRQVRI,%&6HFWLRQRU$&,6HFWLRQDVVHWIRUWKLQ$&,',I
the load combinations of ACI 318 Appendix C are used, the appropriate value of f must be determined in accordance with ACI 318 D.4.5.
3 d0 = drill bit diameter.
)RULQVWDOODWLRQVZLWKDLQHGJHGLVWDQFHWKHLQVWDOODWLRQWRUTXHPXVWEHUHGXFHG3OHDVHUHIHUWRVHFWLRQ
82 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
- 1
Category
Dry concrete and Water-saturated concrete
d & ws - 0.65
Short term elevated concrete temperatures are those that occur over brief intervals, e.g., as a result of diurnal cycling. Long term concrete
temperatures are roughly constant over significant periods of time.
)RUVWUXFWXUHVDVVLJQHGWR6HLVPLF'HVLJQ&DWHJRULHV&'(RU)ERQGVWUHQJWKYDOXHVDUHPXOWLSOLHGE\aN,seis = 1.0 => no reduction.
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 83
Adhesive Anchoring Systems
Chemical Behavior
Sulphuric acid conc.
30%
10% +
Hydrochloric acid conc.
10% +
Nitric acid conc.
10%
Acetic acid conc.
10% +
Formic acid conc.
10%
Lactic acid conc. +
10% +
Citric acid 10% +
Sodium Hydroxide 40%
(Caustic soda) 20% +
5% +
Ammonia conc.
5% +
Soda solution 10% +
Common salt solution 10% +
Chlorinated lime solution 10% +
Sodium hypochlorite 2% +
Hydrogen peroxide 10% +
Carbolic acid solution 10%
(WKDQRO
Sea water +
Glycol +
Acetone
Carbon tetrachloride
Toluene +
Petrol/Gasoline
Machine oil
Diesel oil
.H\ QRQUHVLVWDQW UHVLVWDQW limited resistance
84 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 85
Adhesive Anchoring Systems
Partly used foil packs must be used up within four weeks. Leave
the mixer attached on the foil pack manifold and store under the
recommended storage conditions. If reused, attach a new mixer and
GLVFDUGWKHLQLWLDOTXDQWLW\RIDQFKRUDGKHVLYHDVGHVFULEHGE\SRLQW
Safety instructions:
For industrial use only. Keep out of the reach of children.
See the Material Safety Data Sheet for this product before
handling.
Caution: Irritating to eyes and skin. May
cause sensitization in susceptible individuals.
Contains: dibenzoyl peroxide.
Precautions: Avoid contact with skin/eyes.
Always wear impermeable gloves and eye
protection when using product. Store in a
cool, dry area. Keep from freezing. Do not store in direct sunlight.
First Aid: Eyes Immediately flush with water for 15 minutes, contact
a physician. Skin Wash with soap and water. launder contaminated
clothing before reuse. If irritations occurs, contact physician. Ingestion
Do not induce vomiting unless directed by a physician. Contact a
physician immediately. Inhalation Move to fresh air, give oxygen if
breathing is difficult. contact a physician if symptoms persist.
Made in Germany
86 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 87
Adhesive Anchoring Systems
[mm] [mm] [mm] [Nm] [mm] [mm] Rebar [mm] [mm] [mm] [mm]
M10 12 60 to 200 20 12 10 14 60 to 200 hef + 30
hef + 30
M12 14 70 to 240 40 14 12 16 70 to 240
M18 18 80 to 320 80 18 14 18 75 to 280
M20 24 90 to 400 150 22 hef + 2d0 16 20 80 to 320 hef + 2d0
M24 28 96 to 480 200 28 20 25 90 to 400
25 32 100 to 500
*Tmax(GJH'LVWDQFHFai < (5 x d)
Maximum
(GJH'LVWDQFHFai Anchor Spacing smin
7RUTXH
[GVmin < 16 in. 0.3 x Tmax
(406 mm)
LQPPFai < 5 x d
sminLQ 0.5 x Tmax
(406 mm)
88 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011
Adhesive Anchoring Systems
Order Information
Description Package Contents Qty
+,7+<0$;6'R]/330 mL) MC (1) Includes (1) master carton containing 25 foil packs with (1) mixer and 3/OOHUWXEHSHUSDFN 25
+,7+<0$;6'R]/330 mL) MC (1) + Includes (1) master carton containing 25 foil packs with 1 mixer and 3/OOHUWXEHSHUSDFN 25
MD 2500 Manual Dispenser and (1) MD 2500 Manual Dispenser
+,7+<0$;6'R]/500 mL) MC (1) + Includes (1) master carton containing 20 foil packs with 1 mixer and 3/OOHUWXEHSHUSDFN 20
MD 2500 Manual Dispenser and (1) MD 2500 Manual Dispenser
+,7+<0$;6'R]/500 mL) MC (2) + Includes (2) master cartons containing 20 foil packs each with 1 mixer and 3/OOHUWXEHSHU 40
MD 2500 Manual Dispenser pack and (1) MD 2500 Manual Dispenser
+,7+<0$;6'R]/500 mL) MC (2) + Includes (2) master cartons containing 20 foil packs each with 1 mixer and 3/OOHUWXEHSHU 40
ED 3500-A CPC Cordless Dispenser Kit SDFN('$&3&&RUGOHVV'LVSHQVHU%$K/L,RQEDWWHULHVDQG&/36
Li-Ion charger
+,7+<0$;6'R]/500 mL) MC (5) + Includes (5) master cartons containing 20 foil packs each with 1 mixer and 3/OOHUWXEHSHU 100
MD 2500 Manual Dispensers (2) pack and (2) MD 2500 Manual Dispensers
+,7+<0$;6'R]/500 mL) MC (5) + Includes (5) master cartons containing 20 foil packs each with 1 mixer and 3/OOHUWXEHSHU 100
ED 3500-A CPC Cordless Dispenser Kit SDFN('$&3&&RUGOHVV'LVSHQVHU%$K/L,RQEDWWHULHVDQG&/36
Li-Ion charger
+,7+<0$;6'R]/1400 mL) MC (16) + ,QFOXGHVPDVWHUFDUWRQVFRQWDLQLQJMXPERIRLOSDFNVHDFKZLWKPL[HUDQG/OOHU 64
P 8000 Pneumatic Dispenser (1) 1 pallet tube per pack and (1) P 8000 Pneumatic Dispenser
+,7+<0$;6'R]/1400 mL) MC (32) + ,QFOXGHVPDVWHUFDUWRQVFRQWDLQLQJMXPERIRLOSDFNVHDFKZLWKPL[HUDQG/OOHU 128
P 8000 Pneumatic Dispenser (1) 2 pallets tube per pack and (1) P 8000 Pneumatic Dispenser
+,7+<0$;6'R]/1400 mL) MC (64) + ,QFOXGHVPDVWHUFDUWRQVFRQWDLQLQJMXPERIRLOSDFNVHDFKZLWKPL[HUDQG/OOHU 256
P 8000 Pneumatic Dispenser (1) 4 pallets tube per pack and (1) P 8000 Pneumatic Dispenser
Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011 89
Adhesive Anchoring Systems
Dispensers
90 Hilti, Inc. (US) 1-800-879-8000 | www.us.hilti.com I en espaol 1-800-879-5000 I Hilti (Canada) Corp. 1-800-363-4458 I www.hilti.ca I Anchor Fastening Technical Guide 2011