Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1
Purlin & Girt
LYSAGHT CEE-plus and ZED-plus are products 1.0 mm BMT: G550, Z275
specially designed and developed for purlin and girt 1.9 mm BMT: G350, Z275
application, which not only provides economy to the 2.4 mm BMT: G350, Z275
building construction, but also helps in keeping the
Note: LYSAGHT CEE and ZED section are also
site clean and environment friendly.
available with Zinc coating of 120 g/m2. Please
LYSAGHT CEE-plus and ZED-plus sections are
contact nearest Tata BlueScope Steel office for further
accurately roll-formed from high strength zinc-coated
information.
steel, pre-punched to the required dimensions to
Bolt Specification
provide an efficient, lightweight, economical purlin
LYSAGHT purlin bolts and nuts have integral
and girts.
washers. Tighten all bolts to 55 N-m torque. Nominal
These products are suitable for roof, wall support
section size (mm)
and portal framing up to a certain span. The system,
M12 LYSAGHT purlin bolt
which includes bridging and a comprehensive range
100, 150, 200, 250 standard(grade 4.6) or high
of accessories, is supplied as ready for erection.
strength (grade 8.8)
Benefits
M16 LYSAGHT purlin bolt
Greater Spanning Capability: Cold formed
300*
standard(grade 4.6) or high
galvanized purlins have a minimum yield strength
strength (grade 8.8)
of approximately 60% greater than that of hot rolled
*Non standard items
steel that is typically used for purlins. This high
strength to weight ratio in most applications allows Size and Dimensions
extra spanning capability for the most cost effective The standard sizes for purlins are produced in nominal
structures. depth of 100,150, 200, 250 and 300 mm. The sections
are generally designed by code number signifying the
Easier to Handle: The high strength to low weight
nominal depth and material thickness and letter prefix
ratio makes the product easier to handle both during
to indicate the profile. Purlin are generally produced
transportation and erection.
in thickness of 1.0, 1.2, 1.5, 1.9 and 2.4 mm.
Lower Maintenance Costs: Superior corrosion
resistance of the zinc coating lowers maintenance Z 200 20
costs during its life cycle.
2
Dimensions and Sectional Properties of LYSAGHT Purlins
Lip
W(tp) W(tp) W(tp)
Lip
Lip
thk thk thk
Depth
Depth
Depth
36.5
Lip
L ip
100 / 75
61
W(bt)
40
W(bt) W(bt)
50/40 102
ZED-plus PURLIN ZED-plus PURLIN CEE-plus PURLIN SMARTRUSS C100 & C75 TOPSPAN TS 60 & TS 40
3
Purlin & Girt
Typical Connection
Handling and Storage clean, dry and free of dirt or dust to prevent difficulties
LYSAGHT CEE-plus and ZED-plus sections are when tightening.
delivered in strapped bundles. Ideally, deliveries Bundles of purlins must be lifted carefully to avoid
should be arranged so that the period between damage. Long length should be lifted using a separator
delivery and installation is minimised. If not required bar and fabric slings. Care should be taken to prevent
for immediate use, bundles of purlins should be local damage at the lifting points.
neatly stacked off the ground and on a slight slope
so that water can drain away. If in the open, it should
be protected with waterproof covers to prevent
the entry of water and /or condensation. If bundle
becomes wet, the purlins should be separated, wiped
dry and covered. Other accessories should be treated
similarly. Bolts and nuts in particular should be kept
4
Performance Corrosion Protection
In accordance with the provisions of AS/ANZ A zinc coating of Z275 (275 g/m2 minimum coating
4600:1996 cold-formed steel structures, load mass) is the standard coating class provided with
capacities have been calculated for LYSAGHT
LYSAGHT CEE-plus and ZED-plus sections.
sections using approved LYSAGHT bridging systems,
This will provide a long and trouble-free life for
bolting and other accessories. Sections chosen enclosed buildings and open-sided rural buildings,
using the data provided in the tables will perform as in a non-aggressive environment. A non-aggressive
specified when the design, fabrication and erection environment is 1000 m from rough surf, 750 m from
are carried out in accordance with Tata BlueScope industrial emission and fossil fuel combustion and
Steel recommendations and accepted building 300 m from calm salt waters. Consideration must
practice. be given to the nature of activities performed within
the building. For corrosive environment, please seek
Application Area
advice from Tata BlueScope Steel office.
LYSAGHT ZED-plus sections may be used over
single spans, un-lapped continuous and lapped Compatibility with other Steel Products
continuous spans in multi-bay buildings. Lapped The zinc coating on purlin is fully compatible with
continuous spans result in a considerable capacity the zinc and aluminum / zinc coatings used on roof
increase in the system. LYSAGHT CEE-plus sections and wall sheeting. If minor damage occurs to the
may be used in single spans and un-lapped continuous purlin coating, the base steel is protected by its own
spans in multi-bay buildings. CEE-plus sections are surrounding coating. Furthermore, the protective
ideal as eave Purlin or where compact sections are coating on the sheeting is not corroded by an
required for detailing. CEE-plus sections cannot be un-protected base steel nearby.
lapped.
5
Applications
East Region Kolkata: Tel: +91 33 40061945 Tel: +91 20 6621 8000
writing from Tata BlueScope Steel Ltd. All brand names mentioned
in this brochure are registered trademarks of BlueScope Steel Limited West Region Mumbai: Tel: +91 22 66743329 Website: www.tatabluescopesteel.com
under license to Tata BlueScope Steel Limited." South Region Chennai: Tel: +91 44 42693319 Email: lysaght@tatabluescopesteel.com