Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
2
Type XXXX
67D Series
M1153 M1154
3
67D Series
Table 1. Outlet Pressure Ranges and Control Spring Data
OUTLET PRESSURE CONTROL SPRING DATA
Type RANGES Wire Diameter Free Length
Part Number Color Material
psig bar In. mm In. mm
0 to 20 0 to 1.4 GE07809T012 Green stripe 0.135 3.43 1.43 36.2
0 to 35 0 to 2.4 T14059T0012 Unpainted 0.156 3.96 1.43 36.2
Music Wire
0 to 60 0 to 4.1 T14058T0012 Blue stripe 0.170 4.32 1.43 36.2
67D, 67DR,
0 to 125 0 to 8.6 T14060T0012 Red stripe 0.207 5.26 1.43 36.2
67DF and
67DFR 0 to 35 0 to 2.4 T14113T0012 Silver stripe 0.156 3.96 1.43 36.2
0 to 60 0 to 4.1 T14114T0012 Blue Inconel 0.172 4.37 1.43 36.2
0 to 125 0 to 8.6 T14115T0012 Red 0.207 5.26 1.43 36.2
4
67D Series
Inspect the vent hole regularly to make sure it is
not plugged. Spring case vent hole orientation ! Warning
may be changed by rotating the spring case with
respect to the body. A 1/4 NPT spring case vent To avoid personal injury, property
may be remotely vented by installing obstruction- damage or equipment damage caused
free tubing or piping into the vent. Protect the by bursting of pressure-containing
remote vent by installing a screened vent cap on parts or explosion of accumulated
the remote end of the vent pipe. gas, never adjust the control spring
to produce an outlet pressure higher
5. For use in regulator shutdown, install upstream
than the upper limit of the outlet
block and vent valves and downstream block and
pressure range for that particular
vent valves (if required), or provide some other
spring. If the desired outlet pressure
suitable means of properly venting the regulator
is not within the range of the control
inlet and outlet pressures. Install a pressure gauge
spring, install a spring of the proper
to monitor instruments on startup.
range according to the diaphragm parts
6. Apply a good grade of pipe compound to the maintenanceprocedure.
external pipe threads before making connections,
making sure not to get the pipe compound inside 2. If outlet pressure adjustment is necessary,
theregulator. monitor outlet pressure with a gauge during the
adjustment procedure. The regulator is adjusted
7. Install tubing fitting or piping into the 1/2NPT
by loosening the hex nut (key19), if used, and
inlet connection on the body (key1) and into the
turning the adjusting screw or handwheel (key18)
1/2NPT body outlet connection.
clockwise to increase or counterclockwise to
8. The two 1/4 NPT outlets can be used for a gauge decrease the outlet pressure setting. Retighten the
or other use. If not used, they must be plugged. hex nut to maintain the adjustment position.
5
67D Series
4. Place the diaphragm assembly (key16) on the
! Warning body (key1) as shown in Figure3 or 4. Push
down on the diaphragm assembly to make sure
To avoid personal injury, property
the valve plug (key57) strokes smoothly and
damage or equipment damage caused
approximately 1/16in. / 1.6mm.
by sudden release of pressure or
explosion of accumulated gas, do Note
not attempt any maintenance or In step5, if installing a control spring of
disassembly without first isolating the a different range, be sure to delete the
regulator from system pressure and spring range originally appearing on the
relieving all internal pressure from label and indicate the new spring range.
theregulator.
5. Stack the control spring (key17) and upper spring
Types67D, 67DR, 67DS and 67DSR seat (key20) onto the diaphragm assembly (key16).
6. Install the spring case (key7) on the body (key1)
Trim Maintenance with the vent oriented to prevent clogging or entrance
Key numbers are referenced in Figures3 and 4. of moisture. Install the six spring case screws (key3)
using a crisscross pattern and torque to 15 to
1. Unscrew the spring retainer (key48) and separate 30in-lbs / 1.9 to 3.9 Nm.
the spring retainer and O-ring (key14) from the
body (key1). Note
2. Remove the valve plug (key57) from the spring On Types67DS and 67DSR, lubricate
retainer (key48). Inspect the removed parts for the adjusting screw (key18) thread to
damage and debris. Replace any damaged parts. reduce galling of the stainless steel.
Apply a high quality lubricant to the O-ring (key49)
7. When all maintenance is complete, refer to the
before reassembling.
Startup and Adjustment section to put the regulator
3. To remove the valve stem (key11), grasp the end back into operation and adjust the pressure
and pull it straight out of the body (key1). Inspect setting. Tighten the hex nut (key19) if used, and
the parts for damage and debris. Replace any install the closing cap (key33) if used.
damaged parts. The valve stem may be cleaned
or replaced. If the soft seat (key15) was removed, Types67DF, 67DFR, 67DFS and 67DFSR
make sure it is properly snapped into place before
installing the valve stem. Apply a high quality Filter Element and Trim Maintenance
lubricant to the O-ring (key50) before reinstalling
the valve stem. Key numbers are referenced in Figures5 and 6.
4. Slide valve plug (key57) onto valve stem (key11). 1. Remove four dripwell screws (key3) from the
Apply lubricant to O-ring (key14) and thread in dripwell (key5) and separate the dripwell and
spring retainer (key48). Torque spring retainer to O-ring (key4) from the body (key1). Remove the
10 to 12 ft-lbs / 14 to 16 Nm. screw (key65) that retains the filter (key6) and
remove the filter and filter gasket (key66).
Diaphragm Maintenance 2. Inspect the removed parts for damage and debris.
Replace any damaged parts. If a replacement is
Key numbers are referenced in Figures3 and 4.
not available, the filter element may be cleaned.
1. Back out the adjusting screw or handwheel (key18)
3. To inspect the valve plug (key57), valve stem
until compression is removed from the spring (key17).
(key11) and the valve seat (key58), unscrew the
2. Remove the spring case screws (key3) to spring retainer (key48) and separate from the
separate the spring case (key7) from the body body (key1). To remove the valve plug, grasp
(key1). Remove the upper spring seat (key20) the valve plug and pull it straight out of the spring
and spring (key17). retainer. To remove the valve stem (key11), grasp
3. Remove the diaphragm assembly (key16), the end and pull it straight out of the body (key1).
inspectthe diaphragm, and replace the assembly, Inspect the parts for damage and debris. Inspect
ifnecessary. the valve seat (key58) for damage or wear.
6
67D Series
Replace part if damaged. The valve stem may be 7. When all maintenance is complete, refer to the
cleaned or replaced. If the soft seat (key15) was Startup and Adjustment section to put the regulator
removed, make sure it is properly snapped into back into operation and adjust the pressure
place before installing the valve stem. Apply a setting. Tighten the hex nut (key19) if used, and
high quality lubricant to the O-ring (key50) before install the closing cap (key33) if used.
reinstalling the valve stem.
4. Slide valve plug (key57) onto valve stem (key11). Parts Ordering
Apply lubricant to O-ring (key14) and thread in
spring retainer (key48). Torque spring retainer When corresponding with the local Sales Office about
to 10 to 12 ft-lbs / 14 to 16 Nm. Reinstall the filter this regulator, include the Typenumber and all other
gasket (key66) and filter (key6) and secure it with pertinent information printed on the label. Specify the
the filter retainer (key9) and screw (key65) and eleven-character part number when ordering new
torque to 15 to 30in-lbs / 1.7 to 3.4 Nm. Reinstall parts from the following parts list.
the O-ring (key4), secure the dripwell with When ordering replacement parts, reference the
screws (key3), and torque to 15to 30in-lbs / keynumber of each needed part as found in the
1.7 to 3.4 Nm. following parts list. Separate kit containing all
recommended spare parts is available.
Diaphragm Maintenance
Key numbers are referenced in Figures5 and 6. Parts List
1. Back out the adjusting screw or handwheel Key Description Part Number
(key18) until compression is removed from the Parts Kits
spring (key17). Types67D, 67DR, 67DS and 67DSR -
Includes seat (key58), O-rings (keys 14, 49
2. Remove the six spring case screws (key3) to and 50), soft seat (key15) and diaphragm
separate the spring case (key7) from the body assembly (key16).
(key1). Remove the upper spring seat (key20) Type67D (without relief)
Brass and Nitrile (NBR) seat R67DX000012
and spring (key17). Type67DR (with relief)
Brass and Nitrile (NBR) seat R67DRX00012
3. Remove the diaphragm assembly (key16), Types67D NACE, 67DS and
inspectthe diaphragm and replace the assembly, 67DS NACE (without relief)
ifnecessary. 316L Stainless steel and Nitrile (NBR) seat R67DSX00N12
Types67DR NACE, 67DSR and
4. Place the diaphragm assembly (key16) on the 67DSR NACE (with relief)
body (key1) as shown in Figure5. Push down on 316L Stainless steel and Nitrile (NBR) seat R67DSRX0N12
the diaphragm assembly to make sure the valve Types67DF, 67DFR, 67DFS and 67DFSR -
Includes seat (key58), O-rings (keys 14, 49
plug (key57) strokes smoothly and approximately and 50), soft seat (key15), diaphragm
1/16in. / 1.6mm. assembly (key16), 5 micron polyethylene
filter (key6), filter gasket (key66), dripwell
Note O-ring (key4) and four screws (key3).
In step5, if installing a control spring of Type67DF (without relief)
Brass and Nitrile (NBR) seat R67DFX00012
a different range, be sure to delete the Type67DFR (with relief)
spring range originally appearing on the Brass and Nitrile (NBR) seat
label and indicate the new spring range. Standard kit R67DFRX0012
Low temperature kit (-60F / -51C) R67DFRX0022
Types67DF NACE, 67DFS and
5. Stack the control spring (key17) and upper spring 67DFS NACE (without relief)
seat (key20) onto the diaphragm assembly (key16). 316L Stainless steel and Nitrile (NBR) seat R67DFSX0N12
Types67DFR NACE, 67DFSR and
6. Install the spring case (key7) on the body (key1) 67DFSR NACE (with relief)
with the vent oriented to prevent clogging or entrance 316L Stainless steel and Nitrile (NBR) seat R67DFSRXN12
of moisture. Install the six spring case screws Automatic Drain Conversion Kits
(key3) using a crisscross pattern and torque to 15 to Types67DF, 67DFR, 67DFS and 67DFSR -
30in-lbs / 1.7 to 3.4 Nm. Includes auto-drain (key2), four flange screws (key3),
dripwell O-ring (key4) and dripwell (key5).
Note Note: Temperature rating is
40 to 175F / 4 to 79C.
On Types67DFS and 67DFSR, lubricate Types67DF and 67DFR
the adjusting screw (key18) thread to Nitrile (NBR) R67ADNX0012
Fluorocarbon (FKM) R67ADFX0012
reduce galling of stainless steel.
7
67D Series
Key Description Part Number Key Description Part Number
Automatic Drain Conversion Kits (continued) 14* O-ring (Spring Retainer)
Types67DF, 67DFR, 67DFS and 67DFSR (continued) For Type67D, 67DR, 67DS or 67DSR
Types67DFS and 67DFSR Nitrile (NBR) 10A3803X092
Nitrile (NBR) R67ADNX0022 Fluorocarbon (FKM) 10A3803X112
Fluorocarbon (FKM) R67ADFX0022 Silicone (VMQ) 10A3803X102
15* Soft Seat
1 Body
Nitrile (NBR) T14055T0012
Type67D or 67DR, Aluminum GE31800TGY2
Fluorocarbon (FKM) T14055T0022
Type67DS or 67DSR, CF8M Stainless steel GE31802TGY2
16* Diaphragm Assembly
Type67DF or 67DFR, Aluminum GE31786TGY2
For Type67D or 67DF (without relief)
Type67DFS or 67DFSR, CF8M Stainless steel GE31788X012
Nitrile (NBR) T14119T0022
Type67DFR with Smart Bleed, Aluminum GE33158X012
Fluorocarbon (FKM) T14119T0042
Type67DFSR with Smart Bleed,
For Type67DR or 67DFR (with relief)
Stainless steel GE33159X012
Nitrile (NBR) T14119T0012
2 Drain Valve
Fluorocarbon (FKM) T14119T0032
Type67DF or 67DFR
Silicone (VMQ) T14119T0052
Brass 1K418918992
For Type67DS or 67DFS (without relief)
316 Stainless Steel AH3946X0052
Nitrile (NBR) T14119T0062
Type67DFS or 67DFSR
Fluorocarbon (FKM) T14119T0072
316 Stainless steel AH3946X0052
For Type67DSR or 67DFSR (with relief)
Type67DF, 67DFR, 67DFS or 67DFSR
Nitrile (NBR) T14119T0082
Auto-drain, Nitrile (NBR) GG00554X012
Fluorocarbon (FKM) T14119T0092
Auto-drain, Fluorocarbon (FKM) GG00554X022
Silicone (VMQ) T14119T0102
3 Flange Screw
17 Spring
For Type67D, 67DR, 67DF or 67DFR
For Type67D, 67DR, 67DF or 67DFR,
Standard spring case and spring case
Music wire (standard)
with 1/4 NPT vent (6 or 10 required) T13526T0012
0 to 20 psig / 0 to 1.4 bar, Green stripe GE07809T012
Standard spring case for low
0 to 35 psig / 0 to 2.4 bar, Unpainted T14059T0012
temperature service (6 required) T13526T0042
0 to 60 psig / 0 to 4.1 bar, Blue stripe T14058T0012
For wire seal
0 to 125 psig / 0 to 8.6 bar, Red stripe T14060T0012
Flange Screw (5 or 6 required) T13526T0012
For Type67DR, 67DF or 67DFR
Flange Screw (1 required) 14B3987X012
(NACE), Inconel (NACE)
For Type67DS, 67DSR, 67DFS or
0 to 35 psig / 0 to 2.4 bar, Silver stripe T14113T0012
67DFSR (10 required) T13526T0042
0 to 60 psig / 0 to 4.1 bar, Blue T14114T0012
4* O-ring (Dripwell)
0 to 125 psig / 0 to 8.6 bar, Red T14115T0012
For Type67DF, 67DFR, 67DFS or 67DFSR
For Type67DS, 67DSR, 67DFS or
Nitrile (NBR) T14057T0042
67DFSR, Inconel (NACE)
Fluorocarbon (FKM) T14057T0022
0 to 20 psig / 0 to 1.4 bar, Green 10C1729X012
Silicone (VMQ) T14057T0032
0 to 35 psig / 0 to 2.4 bar, Silver stripe T14113T0012
5 Dripwell
0 to 60 psig / 0 to 4.1 bar, Blue T14114T0012
For Type67DF or 67DFR, Aluminum
0 to 125 psig / 0 to 8.6 bar, Red T14115T0012
Manual GE34605X012
0 to 150 psig / 0 to 10.3 bar, Black 10C1730X012
Auto-drain GE34606X012
18 Adjusting Screw
For Type67DFS or 67DFSR, Stainless steel
For Type67D, 67DR, 67DF or 67DFR
Manual GE34607X012
For standard spring case, Zinc-plated steel
Auto-drain GE31792X012
Square head (standard) T14061T0012
6* Filter Element
Handwheel T14102T0012
For Types67DF, 67DFR, 67DFS and 67DFSR
Wire seal (not shown) T14104T0012
Polyethylene (5 microns) (standard) GE31794X012
For Type67D, 67DR, 67DF or 67DFR (continued)
Glass fiber (5 microns) GE31795X012
For spring case with 1/4 NPT vent
Polyvinylidene fluoride (PVDF) (40 microns) GE31794X022
Square head for closing cap
Stainless steel (40 microns) GE31809X012
Stainless steel T14101T0012
7 Spring Case
Handwheel
For Type67D, 67DR, 67DF or 67DFR, Aluminum
Zinc-plated steel T14103T0012
Drilled hole vent (standard) T14070T0012
Wire seal (not shown)
1/4 NPT vent T14070T0022
Steel T14198T0012
For Type67DS, 67DSR, 67DFS or 67DFSR,
For Type67DS, 67DSR, 67DFS or 67DFSR
Stainless steel 20C1727X012
Square head with or without closing cap
9 Filter Retainer, 316 Stainless steel
Handwheel
For Type67DF, 67DFR, 67DFS or 67DFSR GE31796X012
Stainless steel T14101T0022
11* Valve Stem
Zinc-plated steel T14103T0012
For Types67D, 67DR, 67DF and 67DFR
19 Hex nut
Brass GE35519X012
For Type67D, 67DR, 67DF or 67DFR
Aluminum GE35519X022
Zinc-plated steel 1A946324122
For All
For All
Stainless steel GE35519X032
Stainless steel 1A9463X0042
12* Valve Spring
20 Upper Spring Seat
Stainless steel GE31783X012
For Type67D, 67DR, 67DF or 67DFR
Inconel (NACE) GG00430X012
Zinc-plated steel T14051T0012
*Recommended spare parts For Type67DS, 67DSR, 67DFS or 67DFSR
Inconel is a mark owned by Special Metals Corporation. Stainless steel 10C1725X012
8
67D Series
Key Description Part Number
18 L
22 Pressure Gauge (not shown)
Triple Scale Pressure Connected Gauge
(For Types67D, 67DR, 67DF and 67DFR) 19
Brass
0 to 30 psig / 0 to 2.1 bar / 0 to 0.2 MPa 11B8579X022 20 7
0 to 60 psig / 0 to 4.1 bar / 0 to 0.4 MPa 11B8579X032
0 to 160 psig / 0 to 11.0 bar / 0 to 1.1 MPa 11B8579X042 17 L
For All
Stainless Steel
0 to 30 psig / 0 to 2.1 bar / 0 to 0.2 MPa 11B9639X012
0 to 60 psig / 0 to 4.1 bar / 0 to 0.4 MPa 11B9639X022
0 to 160 psig / 0 to 11.0 bar / 0 to 1.1 MPa 11B9639X032 15
Triple Scale Pressure Top Connected Gauge
(For Types67D, 67DR, 67DF and 67DFR only) 3
50 L
Stainless steel
0 to 30 psig / 0 to 2.1 bar / 0 to 0.2 MPa 11B8582X012
0 to 60 psig / 0 to 4.1 bar / 0 to 0.4 MPa 11B8582X022 11
0 to 160 psig / 0 to 11.0 bar / 0 to 1.1 MPa 11B8582X032 16
23 1/4in. / 6.4mm Pipe Plug (not shown) 58
For Types67D, 67DR, 67DF and 67DFR
Socket head, Steel 1C333528992
For All Typesexcept Types67DF and 67DFS 1 57
Hex head, Stainless steel 1A767535072
For Types67DF and 67DFS L 14 48
Hex head, Stainless steel 1C3335X0012
30 NACE Tag (not shown) ----------- L 49 12
31 Panel Mounting Nut, Stainless steel 10B2657X012
32 Wire Seal (not shown) GE32851_A
For Types67D and 67DR, Stainless steel 1U7581000A2 parts not shown: 25
For Types67DF and 67DFR T14088T0012
apply LUBRICANT (L)
33 Closing Cap, Plastic 23B9152X012
45 Screen Vent (for Types67DS, 67DSR, 67DFS Figure3. Type67D or 67DR Assembly
and 67DFSR only) 0L078343062
48 Spring Retainer
For Type67D or 67DR, Aluminum GG03555X012
For Type67DS or 67DSR, Stainless steel GE31803X022
For Type67DF or 67DFR, Zinc-plated steel GE31797X012
For Type67DFS or 67DFSR, Stainless steel GE31797X022
49* O-ring (Plug) 33 L
Nitrile (NBR) T12946T0012
Fluorocarbon (FKM) 1C8538X0182 18 7
Low Temperature Nitrile (NBR) 1C8538X0192
50* O-ring (Stem)
Nitrile (NBR) 1H2926X0052 19 17
Fluorocarbon (FKM) 1H2926X0062
Low Temperature Nitrile (NBR) 1H2926X0072 20
57 Valve Plug
For Types67D, 67DR, 67DF and 67DFR
Brass GE31779X012 45 3
Aluminum GE31779X022
For All
Stainless steel GE31779X032
58* Seat L
50
Stainless steel/Nitrile (NBR) GE31782X012
Stainless steel/Fluorocarbon (FKM) GE31782X022
For Types67D, 67DR, 67DF and 67DFR 16 1
Brass/Nitrile (NBR) GE31782X032
65 Filter Retainer Screw 15 58
For Types67DF, 67DFR, 67DFS and 67DFSR
Stainless steel T13526T0042
For Types67DF and 67DFR 11 57
Zinc-plated steel T13526T0012
66* Filter Gasket L 49 14 L
For Types67DF, 67DFR, 67DFS and 67DFSR
Nitrile (NBR) GG00752X012 GE31806_A
12 48
Fluorocarbon (FKM) GG00752X022
parts not shown: 25
9
67D Series
33 18
18
19 20
19 L
L 17
20 17
7
7
3
3
16 45 16
L 50 1
15
11
58 50 L
58
1 11
57 15
3 57
3 4 L
L 4 49 L
66 12
66 48
L 49 6
12 9
48 9
6 5
65 2 5 2
GE32850_B GE31805_B
10
67D Series
position 3
18
position 4 position 2
19
31
40C1728_A GE31784_C
Figure7. 67DSeries Optional Panel Mount Figure8. 67DSeries Spring Case Vent Positions
PUSHER POST
(WITHOUT RELIEF)
LOWER SPRING
SEAT
RETAINING RING
DIAPHRAGM
PLATE
B2696
PUSHER POST
(WITH RELIEF)
DIAPHRAGM
11
67D Series
33
18
19
B2698
Figure10. Optional Closing Cap (Only Available with the 1/4in. / 6.4mm Spring Case Vent)
Webadmin.Regulators@emerson.com Facebook.com/EmersonAutomationSolutions
Fisher.com LinkedIn.com/company/emerson-automation-solutions
Twitter.com/emr_automation
D103151X012 2009, 2017 Emerson Process Management Regulator
Technologies, Inc. All rights reserved. 04/17.
Emerson Automation Solutions The Emerson logo is a trademark and service mark of Emerson
Regulator Technologies Electric Co. All other marks are the property of their prospective owners.
Fisher is a mark owned by Fisher Controls International LLC, a
Americas Asia Pacific business of Emerson Automation Solutions.
McKinney, Texas 75070 USA Singapore 128461, Singapore The contents of this publication are presented for information purposes
T+1 800 558 5853 T +65 6770 8337 only, and while effort has been made to ensure their accuracy, they are
+1 972 548 3574 not to be construed as warranties or guarantees, express or implied,
regarding the products or services described herein or their use or
Europe Middle East and Africa applicability. All sales are governed by our terms and conditions, which
Bologna 40013, Italy Dubai, United Arab Emirates are available on request. We reserve the right to modify or improve the
T +39 051 419 0611 T +971 4 811 8100 designs or specifications of our products at any time without notice.
Emerson Process Management Regulator Technologies, Inc. does not
assume responsibility for the selection, use or maintenance of any
product. Responsibility for proper selection, use and maintenance of any
Emerson Process Management Regulator Technologies, Inc. product
remains solely with the purchaser.