Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
FOR
Soil Investigation
TABLE OF CONTENTS
Table of Contents..1
List of Appendix....................................................................................................................................... 2
List of Table............................................................................................................................................. 2
List of Figures.......................................................................................................................................... 2
Figures
Appendix
Tables
1
Infratech ASTM CO., LTD.
List of Appendix
List of Table
2
Infratech ASTM CO., LTD.
3.1 General
The investigation program included drilling boreholes and collecting soil samples at desired
intervals for subsequent observation and laboratory testing.
The investigation program will consist of soil boring and sampling at desired intervals for
subsequent observation and laboratory testing to determine the capacity of pile foundation economically
and safely.
Disturbed samples for very stiff clay to hard clay layer will be collected during Standard
Penetration Testing at 1.5 m intervals. (ASTM D 1586)
The borings shall be drilled vertically through soil approximately 30 meters deep or stop in firm
layer when SPT N-value is greater than 50 blows/ft.
Accuracy of bore hole position will be not more than 2.0 m. in horizontal direction and 0.20 in
vertical direction.
3
Infratech ASTM CO., LTD.
be expressed as an N value. The N value is defined as the blow-count for 12 (300mm) penetration
recorded after the seating drive of 15 cm. In the case of premature refusal conditions, the number of
blows for a recorded penetration (including the seating drive) is noted.
In SPT testing, the rope-and-pulley (R-P) method will be used. This consisted of a hollow
cylindrical mass sliding over a steel rod. It is operated by lifting the mass with a rope over a cat head. At
the instant the mass reached the required height (760 mm), the mass will be released manually driving
the split spoon into the soil. Disturbed samples collected from the split-spoon sampler during Standard
Penetration Test will be visually inspected before storing in a polyethylene bag for laboratory testing. A
graphical representation of the changes in the soil strata, water levels and SPT N values will be given in
the boring logs.
4
Infratech ASTM CO., LTD.
The test shall be intended to collect shear wave velocity information that will be used in dynamic
analysis. The testing location shall be located in the power block area and close to expected location of
Steam Turbine foundation.
Sample of test results and data sheet has been shown in Table 1
Sample of test results and data sheet has been shown in Table 2
5
Infratech ASTM CO., LTD.
4.3 Particle Size Analysis
Particle size analysis will be performed by means of sieving (ASTM D 422). For oven-dry
materials, sieving is carried out for particles that are being retained on a 0.063 mm sieve. In sieve
analysis, the mass of soil retained on each sieve is determined and expressed as a percentage of the
total mass of the sample. The particle size is plotted on a logarithmic scale so that two soils having the
same degree of uniformity are represented by curves of the distribution plot. In Hydrometer analysis is
based on the principle of sedimentation of soil grains in water. When a soil specimen is dispersed in
water, the particles settle at different velocities, depending on their shape, size, and weight. For
simplicity, it is assumed that soil particles are spheres and the velocity of soil particles can be express by
Stokes law.
Sample of test results and data sheet has been shown in Table 3
Sample of test results and data sheet has been shown in Table 4 and Table 5
Oedometer tests will be conducted (ASTM D 2435) to determine the rate and magnitude of
consolidation of a laterally restrained soil specimen which is axially loaded in increments of constant
stress until the excess pore water pressures have dissipated for each increment. Each load increment is
maintained for at least 24 hours. The test is generally carried out on undisturbed cohesive specimens.
Sample of test results and data sheet has been shown in Table 6
6
Infratech ASTM CO., LTD.
5.0 REPORT
Confirmed Preliminary Report findings along with the remainder of test results to be
Submitted in a Final Report.
7
APPENDIX A
Sample No.
SPT-N (Blow/30cm.)
Depth (m)
Recovery
Method
40 80 20 40 60 80 100
SOIL DESCRIPTION
t (t/m3) Su (t/m2)
1.0 2.0 2 4 6 8 10
0 Borehole Elevation = 1.99 m.
SS 5 1.89 14
15
SS 6 Brown, moist, high plasticity, 1.96 16
stiff to very stiff,
Sandy Clay.
SS 7 (CH) 15
trace gravel.
SS 8 17
20 SS 9 19.95 m. 22
SS 10 58
Brown, moist, medium plasticity,
hard, Sandy Clay.
SS 11 (CL) 76
24.45 m. 1.93
SS 12
End of Boring = 24.45 m.
Sample sheet
ASTM TESTING CO.,LTD. SUMMARY OF TEST RESULTS
Depth. (m.) USCS Wn,at UC Test wet, Atterberg Limits Gradation % Passing Nspt
ST - 3 4.50 5.00 CL 55.20 2.14 1.69 40.05 24.33 15.72 100.00 99.77 98.51 94.33
SS - 1 7.50 7.95 CH 31.07 1.81 56.08 23.51 32.56 99.04 98.92 98.11 91.63 9
SS - 2 9.00 9.45 10
SS - 3 10.50 10.95 CL 22.04 1.96 48.11 21.29 26.82 100.00 99.85 99.29 95.86 22
SS - 7 16.50 16.95 CH 32.88 60.30 28.53 31.77 93.45 91.79 89.23 85.09 15 Sandy Clay (CH)
SS - 9 19.50 19.95 22
SS - 10 21.00 21.45 58
SS - 11 22.50 22.95 CL 17.82 41.11 18.58 22.54 99.70 99.30 96.57 82.52 76 Sandy Clay (CL).
Pile Calculation
Sample sheet
Appendix B 1 - BH-1
(Estimation of Soil Bearing Capacity)
BH-1
PROJECT : Saraburi A Cogeneration Co.,ltd.
LOCATION : Saraburi
BOREHOLE NO.: BH-1
0 10 20 30 40 50 60 70 80 90 100
0
Depth (m)
5
Ultimate End Bearing(t/sq.m.)
Location: Saraburi
Borehole No.: BH-1
Factor of safety : 3.00
Allowable settlement, Se 25.0 mm.
Depth of water = 1.53 m below ground level
Depth Soil Description Unit weight SPT (N-value) vo,base 'vo,base Cohesion, Su FDN Dimension NET SOIL BEARING CAPACITY SUMMARY
USCS S=Sand Field Correct Design B L CLAY SAND Depth qall
Df C=Clay t/m2 kN/m2 NF Ncor. Ndesign t/m2 t/m2 kN/m2 t/m2 kN/m2
o
m. m. qu (kPa) qall (kPa) qall (t/m2) Fd qall (kPa) qall (t/m2) (m) (t/m2)
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 - - - - - - - - - - - - -
1.0 CL C 2.0 19.6 9 20 13 2.00 2.00 19.62 7.89 77.39 1.0 1.0 572.8 190.9 19.5 1.0 19.5
2.0 CL C 2.0 19.6 12 20 15 4.00 3.53 34.63 9.15 89.80 1.0 1.0 775.4 258.5 26.3 2.0 26.3
3.0 CL C 2.0 19.6 15 22 17 6.00 4.53 44.44 10.83 106.28 1.0 1.0 1048.8 349.6 35.6 3.0 35.6
4.0 CL C 2.1 20.2 20 26 22 8.06 5.59 54.84 13.83 135.72 1.0 1.0 1506.8 502.3 51.2 4.0 51.2
BH-1
RECOMMENDED PILE LENGTH AND CAPACITY FOR FOR SINGLE PILE
Driven Pile 0.25x0.25 12.0 39 32 0.2 40 Can not be installed when SPT>=Limit
Driven Pile 0.30x0.30 12.0 48 38 0.3 55 Can not be installed when SPT>=Limit
Driven Pile 0.35x0.35 12.0 58 45 0.5 70 Can not be installed when SPT>=Limit
Driven Pile 0.40x0.40 12.0 68 51 0.6 80 Can not be installed when SPT>=Limit
Driven Pile may not be installed pass through depth where SPT limit >= 50
RECOMMENDED ALLOWABLE LOAD FOR SINGLE SQUARE DRIVEN PILE
25 x 25 cm. Square Driven Pile 30 x 30 cm. Square Driven Pile 35 x 35 cm. Square Driven Pile 40 x 40 cm. Square Driven Pile
Depth
Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable
(meters) Friction Bearing Weight Load Friction Bearing Weight Load Friction Bearing Weight Load Friction Bearing Weight Load
(tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons)
4.0 19.4 8.3 0.5 10.9 23.3 11.9 0.6 13.8 27.2 16.2 0.9 17.0 31.1 21.2 1.2 20.4
5.0 25.5 10.0 0.6 14.0 30.6 14.5 0.9 17.7 35.8 19.7 1.2 21.7 40.9 25.7 1.5 26.0
7.5 42.0 11.6 1.0 21.1 50.4 16.7 1.4 26.3 58.9 22.7 1.9 31.9 67.3 29.6 2.5 37.8
9.0 54.5 16.3 1.2 27.9 65.5 23.5 1.7 34.9 76.4 32.0 2.4 42.4 87.3 41.8 3.1 50.4
10.5 66.7 15.9 1.4 32.4 80.0 22.9 2.1 40.3 93.4 31.1 2.8 48.7 106.7 40.6 3.6 57.5
12.0 79.9 18.1 1.7 38.6 95.9 26.1 2.4 47.9 111.9 35.6 3.2 57.7 127.9 46.4 4.2 68.0
13.5 94.9 21.4 1.9 45.8 113.9 30.8 2.7 56.8 132.9 41.9 3.7 68.4 151.9 54.7 4.8 80.7
15.0 112.2 24.5 2.1 53.8 134.6 35.3 3.0 66.7 157.0 48.1 4.1 80.4 179.4 62.8 5.4 94.7
35 cm. Dia. Bored Pile 40 cm. Dia. Bored Pile 50 cm. Dia. Bored Pile 60 cm. Dia. Bored Pile
Depth
Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable
(meters) Friction Bearing Weight Load Friction Bearing Weight Load Friction Bearing Weight Load Friction Bearing Weight Load
(tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons)
4.0 31.2 12.8 0.7 17.3 35.7 16.7 0.9 20.6 44.6 26.0 1.4 27.7 53.6 37.5 2.0 35.6
5.0 41.1 15.5 0.9 22.3 47.0 20.2 1.2 26.4 58.7 31.5 1.9 35.4 70.5 45.4 2.7 45.3
7.5 67.7 17.8 1.5 33.6 77.3 23.3 2.0 39.5 96.7 36.4 3.1 52.0 116.0 52.4 4.4 65.6
9.0 87.8 25.1 1.8 44.4 100.4 32.8 2.4 52.3 125.5 51.3 3.8 69.2 150.5 73.9 5.4 87.6
10.5 107.4 24.4 2.2 51.8 122.7 31.9 2.9 60.7 153.4 49.9 4.5 79.5 184.0 71.8 6.4 99.8
12.0 128.7 27.9 2.5 61.6 147.1 36.5 3.3 72.1 183.8 57.0 5.2 94.3 220.6 82.1 7.5 118.1
13.5 152.8 32.9 2.9 73.1 174.6 43.0 3.8 85.5 218.3 67.1 5.9 111.8 261.9 96.7 8.5 140.1
15.0 180.6 37.8 3.2 86.0 206.4 49.3 4.2 100.6 257.9 77.1 6.6 131.4 309.5 111.0 9.5 164.4
Graph
(Cumulative Ultimate Skin Friction & Ultimate End
Bearing Capacity & Depth)
BH-1
PROJECT : Saraburi A Cogeneration Co.,ltd.
LOCATION : Saraburi
BOREHOLE NO.: BH-1
2 2
4 4
6 6
Depth (m)
Depth (m)
8 8
10 10
12 12
14 14
16 16
Ultinate Skin Friction(t/m.Perimeter) Ultimate End Bearing(t/sq.m.)
CUMMULATIVE ULTIMATE SKIN FRICTION AND ULTIMATE END BEARING CAPACITY VS DEPTH OF DRIVEN PILE
PROJECT : Saraburi A Cogeneration Co.,ltd.
LOCATION : Saraburi
BOREHOLE NO.: BH-1
2 2
4 4
6 6
Depth (m)
Depth (m)
8 8
10 10
12 12
14 14
16 16
Ultinate Skin Friction(t/m.Perimeter) Ultimate End Bearing(t/sq.m.)
CUMMULATIVE ULTIMATE SKIN FRICTION AND ULTIMATE END BEARING CAPACITY VS DEPTH OF BORED PILE
Appendix B 4
BH-1
SINGLE SQUARE DRIVEN PILE CAPACITY CALCULATION-STATIC FORMULA
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 4.4 4.6 4.4 4.4 4.4 0.0 8.9 3.6
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 4.5 5.4 4.5 8.9 8.9 0.2 9.8 5.7
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 4.9 6.5 4.9 13.9 13.9 0.3 11.1 8.0
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 5.6 8.3 5.6 19.4 19.4 0.5 13.4 10.9
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 6.1 10.0 6.1 25.5 25.5 0.6 15.6 14.0
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 6.6 11.6 16.5 42.0 42.0 1.0 27.1 21.1
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 8.3 16.3 12.5 54.5 54.5 1.2 27.6 27.9
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 8.1 15.9 12.1 66.7 66.7 1.4 26.6 32.4
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 8.8 18.1 13.2 79.9 79.9 1.7 29.7 38.6
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 10.0 21.4 15.0 94.9 94.9 1.9 34.5 45.8
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 11.5 24.5 17.2 112.2 112.2 2.1 39.7 53.8
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0
15.0
15.0
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 4.4 6.6 5.2 5.2 4.4 0.0 11.8 4.7
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 4.5 7.8 5.5 10.7 8.9 0.2 13.0 7.3
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 4.9 9.3 5.9 16.6 13.9 0.4 14.8 10.2
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 5.6 11.9 6.7 23.3 19.4 0.6 17.9 13.8
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 6.1 14.5 7.4 30.6 25.5 0.9 20.9 17.7
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 6.6 16.7 19.8 50.4 42.0 1.4 35.1 26.3
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 8.3 23.5 15.0 65.5 54.5 1.7 36.8 34.9
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 8.1 22.9 14.6 80.0 66.7 2.1 35.4 40.3
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 8.8 26.1 15.9 95.9 79.9 2.4 39.6 47.9
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 10.0 30.8 18.0 113.9 94.9 2.7 46.0 56.8
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 11.5 35.3 20.7 134.6 112.2 3.0 53.0 66.7
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0
15.0
15.0
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 4.4 8.9 6.1 6.1 4.4 0.0 15.1 6.0
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 4.5 10.6 6.4 12.5 8.9 0.3 16.7 9.1
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 4.9 12.7 6.9 19.4 13.9 0.6 19.0 12.6
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 5.6 16.2 7.8 27.2 19.4 0.9 23.1 17.0
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 6.1 19.7 8.6 35.8 25.5 1.2 27.1 21.7
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 6.6 22.7 23.1 58.9 42.0 1.9 43.9 31.9
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 8.3 32.0 17.5 76.4 54.5 2.4 47.1 42.4
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 8.1 31.1 17.0 93.4 66.7 2.8 45.3 48.7
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 8.8 35.6 18.5 111.9 79.9 3.2 50.9 57.7
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 10.0 41.9 21.0 132.9 94.9 3.7 59.2 68.4
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 11.5 48.1 24.1 157.0 112.2 4.1 68.1 80.4
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0
15.0
15.0
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 4.4 11.7 7.0 7.0 4.4 0.0 18.7 7.5
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 4.5 13.8 7.3 14.3 8.9 0.4 20.7 11.1
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 4.9 16.6 7.9 22.2 13.9 0.8 23.7 15.2
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 5.6 21.2 8.9 31.1 19.4 1.2 28.9 20.4
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 6.1 25.7 9.8 40.9 25.5 1.5 34.0 26.0
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 6.6 29.6 26.4 67.3 42.0 2.5 53.5 37.8
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 8.3 41.8 20.0 87.3 54.5 3.1 58.7 50.4
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 8.1 40.6 19.4 106.7 66.7 3.6 56.4 57.5
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 8.8 46.4 21.2 127.9 79.9 4.2 63.4 68.0
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 10.0 54.7 24.0 151.9 94.9 4.8 73.9 80.7
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 11.5 62.8 27.6 179.4 112.2 5.4 85.0 94.7
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0 392.3 112.2
15.0
15.0
15.0
BH-1
SINGLE BORED PILE CAPACITY CALCULATION-STATIC FORMULA
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 5.0 7.0 7.0 7.0 5.0 0.0 14.1 5.6
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 5.2 8.3 7.3 14.4 10.3 0.2 15.4 9.0
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 5.7 10.0 8.0 22.3 15.9 0.5 17.5 12.7
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 6.4 12.8 8.9 31.2 22.3 0.7 21.0 17.3
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 7.0 15.5 9.9 41.1 29.4 0.9 24.4 22.3
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 7.6 17.8 26.6 67.7 48.3 1.5 42.9 33.6
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 9.6 25.1 20.1 87.8 62.7 1.8 43.4 44.4
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 9.3 24.4 19.5 107.4 76.7 2.2 41.8 51.8
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 10.2 27.9 21.3 128.7 91.9 2.5 46.7 61.6
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 11.5 32.9 24.1 152.8 109.1 2.9 54.1 73.1
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 13.2 37.8 27.8 180.6 129.0 3.2 62.3 86.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0
15.0
15.0
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 5.0 9.2 8.0 8.0 5.0 0.0 17.2 6.9
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 5.2 10.9 8.4 16.4 10.3 0.3 18.9 10.8
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 5.7 13.0 9.1 25.5 15.9 0.6 21.5 15.2
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 6.4 16.7 10.2 35.7 22.3 0.9 26.0 20.6
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 7.0 20.2 11.3 47.0 29.4 1.2 30.3 26.4
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 7.6 23.3 30.4 77.3 48.3 2.0 51.7 39.5
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 9.6 32.8 23.0 100.4 62.7 2.4 53.4 52.3
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 9.3 31.9 22.3 122.7 76.7 2.9 51.4 60.7
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 10.2 36.5 24.4 147.1 91.9 3.3 57.5 72.1
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 11.5 43.0 27.6 174.6 109.1 3.8 66.8 85.5
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 13.2 49.3 31.7 206.4 129.0 4.2 76.8 100.6
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0
15.0
15.0
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 5.0 14.3 10.1 10.1 5.0 0.0 24.4 9.8
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 5.2 17.0 10.5 20.5 10.3 0.5 27.0 14.8
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 5.7 20.3 11.4 31.9 15.9 0.9 30.7 20.5
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 6.4 26.0 12.8 44.6 22.3 1.4 37.4 27.7
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 7.0 31.5 14.1 58.7 29.4 1.9 43.8 35.4
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 7.6 36.4 37.9 96.7 48.3 3.1 71.3 52.0
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 9.6 51.3 28.8 125.5 62.7 3.8 76.3 69.2
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 9.3 49.9 27.9 153.4 76.7 4.5 73.3 79.5
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 10.2 57.0 30.5 183.8 91.9 5.2 82.3 94.3
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 11.5 67.1 34.5 218.3 109.1 5.9 95.7 111.8
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 13.2 77.1 39.7 257.9 129.0 6.6 110.1 131.4
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0
15.0
15.0
Depth Soil Description Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
To USCS S=Sand Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay t/m2 kN/m2 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
0.0 - - 0.00 0.00 0 0 0 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 CL C 2.0 19.62 9 20 13 2.00 2.00 19.62 1.00 9.81 7.89 - - - - 0.55 73.0 5.0 20.6 12.1 12.1 5.0 0.0 32.7 13.1
2.0 CL C 2.0 19.62 12 20 15 4.00 3.53 34.63 2.77 27.12 9.15 - - - - 0.50 86.4 5.2 24.4 12.6 24.6 10.3 0.7 36.3 19.3
3.0 CL C 2.0 19.62 15 22 17 6.00 4.53 44.44 4.03 39.53 10.83 - - - - 0.46 103.5 5.7 29.3 13.6 38.2 15.9 1.4 41.5 26.5
4.0 CL C 2.1 20.21 20 26 22 8.06 5.59 54.84 5.06 49.64 13.83 - - - - 0.40 132.6 6.4 37.5 15.3 53.6 22.3 2.0 50.8 35.6
5.0 CL C 2.1 20.21 25 30 27 10.12 6.65 65.24 6.12 60.04 16.72 - - - - 0.37 160.6 7.0 45.4 16.9 70.5 29.4 2.7 59.6 45.3
7.5 CL C 2.1 20.40 30 31 30 15.32 9.35 91.72 8.00 78.48 18.88 - - - - 0.35 185.2 7.6 52.4 45.5 116.0 48.3 4.4 93.5 65.6
9.0 SC C 2.1 20.60 44 41 43 18.47 11.00 107.91 10.18 99.82 26.96 - - - - 0.31 261.1 9.6 73.9 34.5 150.5 62.7 5.4 103.0 87.6
10.5 SC C 2.0 19.62 43 38 41 21.47 12.50 122.63 11.75 115.27 25.83 - - - - 0.31 253.9 9.3 71.8 33.5 184.0 76.7 6.4 98.9 99.8
12.0 SC C 2.0 19.42 50 42 47 24.44 13.97 137.05 13.24 129.84 29.53 - - - - 0.30 290.2 10.2 82.1 36.6 220.6 91.9 7.5 111.2 118.1
13.5 CL C 2.0 19.42 60 48 56 27.41 15.44 151.47 14.71 144.26 34.93 - - - - 0.29 341.8 11.5 96.7 41.3 261.9 109.1 8.5 129.5 140.1
15.0 SG C 2.1 20.11 70 53 64 30.49 17.02 166.92 16.23 159.19 40.20 - - - - 0.29 392.3 13.2 111.0 47.6 309.5 129.0 9.5 149.1 164.4
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0 392.3 129.0
15.0
15.0
15.0
Pile Calculation
Sample sheet
SINGLE SQUARE DRIVEN PILE CAPACITY CALCULATION-STATIC FORMULA
Soil Description Depth Avg. Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
USCS S=Sand To Depth Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay m t/m^3 kN/m^3 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
- - 0.0 0.00 0.00 0.00 0 0 1.00 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
CH C 3.0 1.50 2.12 20.80 9 15 0.59 6.36 3.36 32.96 1.68 16.48 2.25 - - - - 1.00 183.9 2.3 11.5 6.8 6.8 6.8 0.0 18.2 7.3
CH C 7.0 3.50 2.12 20.80 15 17 0.90 14.84 7.84 76.91 5.60 54.94 3.75 - - - - 0.95 200.7 3.6 12.5 14.2 21.0 21.0 0.6 32.9 13.2
CL C 13.5 6.75 2.12 20.80 24 19 1.25 28.62 15.12 148.33 11.48 112.62 6.00 - - - - 0.64 231.2 3.8 14.5 25.0 45.9 45.9 1.6 58.8 23.5
SM S 16.0 8.00 2.13 20.90 51 38 1.36 33.95 17.95 176.04 16.53 162.18 12.75 28 8 0.50 22 - 451.0 6.8 28.2 17.0 63.0 63.0 2.0 89.2 35.7
SP S 17.5 8.75 2.13 20.90 80 56 1.42 37.14 19.64 192.67 18.79 184.35 20.00 42 80 0.50 34 - 676.2 12.5 42.3 18.7 81.7 81.7 2.2 121.8 48.7
SP-SM S 18.5 9.25 2.13 20.90 100 68 1.46 39.27 20.77 203.75 20.21 198.21 25.00 51 108 0.50 41 - 822.0 17.4 51.4 17.4 99.1 99.1 2.3 148.2 59.3
Soil Description Depth Avg. Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
USCS S=Sand To Depth Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay m t/m^3 kN/m^3 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
- - 0.0 0.00 0.00 0.00 0 0 1.00 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
CH C 3.0 1.50 2.12 20.80 9 15 0.59 6.36 3.36 32.96 1.68 16.48 2.25 - - - - 1.00 183.9 2.3 16.6 8.1 8.1 6.8 0.0 24.7 9.9
CH C 7.0 3.50 2.12 20.80 15 17 0.90 14.84 7.84 76.91 5.60 54.94 3.75 - - - - 0.95 200.7 3.6 18.1 17.1 25.2 21.0 0.9 42.4 16.9
CL C 13.5 6.75 2.12 20.80 24 19 1.25 28.62 15.12 148.33 11.48 112.62 6.00 - - - - 0.64 231.2 3.8 20.8 30.0 55.1 45.9 2.3 73.7 29.5
SM S 16.0 8.00 2.13 20.90 51 38 1.36 33.95 17.95 176.04 16.53 162.18 12.75 28 8 0.50 22 - 451.0 6.8 40.6 20.4 75.6 63.0 2.8 113.3 45.3
SP S 17.5 8.75 2.13 20.90 80 56 1.42 37.14 19.64 192.67 18.79 184.35 20.00 42 80 0.50 34 - 676.2 12.5 60.9 22.5 98.0 81.7 3.1 155.8 62.3
SP-SM S 18.5 9.25 2.13 20.90 100 68 1.46 39.27 20.77 203.75 20.21 198.21 25.00 51 108 0.50 41 - 822.0 17.4 74.0 20.9 119.0 99.1 3.3 189.6 75.8
Soil Description Depth Avg. Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
USCS S=Sand To Depth Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay m t/m^3 kN/m^3 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
- - 0.0 0.00 0.00 0.00 0 0 1.00 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
CH C 3.0 1.50 2.12 20.80 9 15 0.59 6.36 3.36 32.96 1.68 16.48 2.25 - - - - 1.00 183.9 2.3 22.5 9.5 9.5 6.8 0.0 32.0 12.8
CH C 7.0 3.50 2.12 20.80 15 17 0.90 14.84 7.84 76.91 5.60 54.94 3.75 - - - - 0.95 200.7 3.6 24.6 19.9 29.3 21.0 1.2 52.8 21.1
CL C 13.5 6.75 2.12 20.80 24 19 1.25 28.62 15.12 148.33 11.48 112.62 6.00 - - - - 0.64 231.2 3.8 28.3 35.0 64.3 45.9 3.1 89.5 35.8
SM S 16.0 8.00 2.13 20.90 51 38 1.36 33.95 17.95 176.04 16.53 162.18 12.75 28 8 0.50 22 - 451.0 6.8 55.2 23.8 88.2 63.0 3.8 139.6 55.8
SP S 17.5 8.75 2.13 20.90 80 56 1.42 37.14 19.64 192.67 18.79 184.35 20.00 42 80 0.50 34 - 676.2 12.5 82.8 26.2 114.4 81.7 4.3 193.0 77.2
SP-SM S 18.5 9.25 2.13 20.90 100 68 1.46 39.27 20.77 203.75 20.21 198.21 25.00 51 108 0.50 41 - 822.0 17.4 100.7 24.4 138.8 99.1 4.6 234.9 94.0
Soil Description Depth Avg. Unit Unit SPT (N-value) vo 'tip 'tip 'ave 'ave Su Nq Ks Adh. qb qs Qb Qs Qs Qs Wp Qu Qa
USCS S=Sand To Depth Weight Weight Field Liao Corr. Factor Cumm. Cumm.
C=Clay m t/m^3 kN/m^3 t/m2 t/m2 kN/m2 t/m2 kN/m2 t/m2
o
0.80 t/m2 t/m2 tons tons tons t/m. peri tons tons tons
- - 0.0 0.00 0.00 0.00 0 0 1.00 0.00 0.00 0.00 0.00 0.00 - - - - - - 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
CH C 3.0 1.50 2.12 20.80 9 15 0.59 6.36 3.36 32.96 1.68 16.48 2.25 - - - - 1.00 183.9 2.3 29.4 10.8 10.8 6.8 0.0 40.2 16.1
CH C 7.0 3.50 2.12 20.80 15 17 0.90 14.84 7.84 76.91 5.60 54.94 3.75 - - - - 0.95 200.7 3.6 32.1 22.7 33.5 21.0 1.5 64.1 25.6
CL C 13.5 6.75 2.12 20.80 24 19 1.25 28.62 15.12 148.33 11.48 112.62 6.00 - - - - 0.64 231.2 3.8 37.0 40.0 73.5 45.9 4.0 106.5 42.6
SM S 16.0 8.00 2.13 20.90 51 38 1.36 33.95 17.95 176.04 16.53 162.18 12.75 28 8 0.50 22 - 451.0 6.8 72.2 27.3 100.8 63.0 5.0 167.9 67.2
SP S 17.5 8.75 2.13 20.90 80 56 1.42 37.14 19.64 192.67 18.79 184.35 20.00 42 80 0.50 34 - 676.2 12.5 108.2 30.0 130.7 81.7 5.6 233.3 93.3
SP-SM S 18.5 9.25 2.13 20.90 100 68 1.46 39.27 20.77 203.75 20.21 198.21 25.00 51 108 0.50 41 - 822.0 17.4 131.5 27.9 158.6 99.1 6.0 284.2 113.7
25 x 25 cm. Square Driven Pile 30x30 cm. square Driven Pile 35x35 cm. square Driven Pile 40x40 cm. square Driven Pile
Depth
Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable Cumm.Skin End Pile Allowable
(meters) Friction Bearing Weight Load Friction Bearing Weight Load Friction Bearing Weight Load Friction Bearing Weight Load
(tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons) (tons)
13.5 46 14 2 24 55 21 2 29 64 28 3 36 73 37 4 43
16.0 63 28 2 36 76 41 3 45 88 55 4 56 101 72 5 67
17.5 82 42 2 49 98 61 3 62 114 83 4 77 131 108 6 93
18.5 99 51 2 59 119 74 3 76 139 101 5 94 159 132 6 114
2 2
4 4
6 6
8 8
Depth (m)
Depth (m)
10 10
12 12
14 14
16 16
18 18
20 20
CUMMULATIVE ULTIMATE SKIN FRICTION AND ULTIMATE END BEARING CAPACITY VS DEPTH OF SINGLE SQUARE DRIVEN PILE
Appendix D
all calculations are done for SPT blow count N60=15 at depth 7.92 m; Corrected SPT N1(60)~13 after Liao and Whitman 1986
Table i : Input data and assumptions. Table ii : Soil layers from existing ground.
Input Parameter Value Thickness Unit
Footing B (m) 1 ( )
3 W
16.5i ht
Footing L (m) 1 4.3 18.7
Footing Df (m) 0.9 5 17.5
Footing P (kPa) 100
Safety factor FS 3
Apply ground water No
Ground ti water level -
(Pile
) length (m) 5
Pile diameter (m) 0.4
Bowles, 1996 and Denver, 1982 27111 Sand (normally consolidated) 25 N60
Bowles, 1996 41250 Sands (all normally consolidated): average value 25 N60
Kulhawy and Mayne, 1990 15000 Clean sands (normally consolidated) N60
Kulhawy and Mayne, 1990 22500 Clean sands (over consolidated) N60
Tan et al., 1991 6300 Silts, sandy silt, or clayey silt N60
Ghahramani and Behpoor, 1989 112 based on over 100 data in Iran, N60<25 7 N60
Hatef and Keshavarz, 2004 104 based on 482 SPT and unconfined compression tests in Shiraz 39 N60
city (Iran)
Tavares, 1988 105 for clays in Brazil 39 N60
Meyerhof, 1957 54
Terzaghi 247.57 Ng from Brinch and Hansen 1970, Nq from Bowles 1996, Fi from
Hatanaka and Uchida, 1996
Meyerhof, 1976 390
modified Meyerhof, 1965 0.36 revised method after Meyerhof, 1956 N60ave
Peck, Hanson and Thornburn, 1974 2.34 valid for B>0.9 m N60ave
Burland and Burbidge, 1985 0.28 for normally consolidates sands N60ave
Burland and Burbidge, 1985 0.03 for over consolidates sands N60ave
Duncan and Buchignani, 1976 0.65 modified from Meyerhof 1965, for 1 year time effect N60ave
Table 25 : Consistency.
Source Consistency Comments Ref# Var.
Terzaghi, Peck and Mesri, 1996 31.8 Coarse-grained sands 23,27 N60
Dunham, 1954 33.4 Round and well-graded OR Angular and uniform-graded soils 4 N60
Shioi and Fukui, 1954 30.2 for roads and bridges 1 N70
Peck, Hanson and Thornburn, 1974 31.7 is not recommended for shallow depths (less than 1 to 2 metres) 12 N1(60)
Moh, Chin, Lin and Woo, 1989 32.7 granular soils in Taipei 33 N1(60)
Reese and O'Neill, 1988 192 fs for drilled piles (beta method, function of depth) 46 -
Hassan and O'Neill, 1994 192 fs for drilled piles (modified beta method, function of depth) 46 N60
Meyerhof, 1976 1502 qp for small displacement piles (bored) with upper limit cut-off 28 N1(60)
Meyerhof, 1976 5008 qp for large displacement piles (driven) with upper limit cut-off 28 N1(60)
Yves Robert, 1997 1440 qp for bored piles in granular soil 28 N1(60)
Yves Robert, 1997 2379 qp for driven piles in granular soil 28 N1(60)
Reese and O'Neill, 1988 900 qp with upper limit of 4300 KPa in drilled shafts 46 N60
J. Fred Triggs and Paul D. 25 Wildcat Dynamic Penetrometer blow counts /10cm N60
Simpson, 1990
Stroud, 1989 ~ 133.12 E-6 mv for PI=15%, in 1/kPa N1(60)
Ohya, 1982 5424 Pressuremeter horizontal modulus (E_PMT) in sands, in kPa N60
Kulhawy and Mayne, 1990 17.3 Saturated unit weight for Sands, in kN/m3 N60
Kulhawy and Mayne, 1990 18.9 Saturated unit weight for Clays, in kN/m3 N60
Ulugergerli and Uyanik, 2004 ~ 16.6 to 19.4 Unit weight for clay, slit and gravel in western Turkey (using N60
average Vs), in kN/m3
Ziaie Moayed and Naeini, 2006 106.1 Modulus of subgrade reaction Ks30 in gravely soils, in MN/m3 29 N1(60)
Mayne and Kemper, 1984 6.2 Over Consolidation Ratio (OCR) for clays N60
Muayed Ismail, 2008 ~ 1.3 E-3 D10 for granular soil near Baghdad N60<35, in mm 32 N60
Schnaid et al., 2004 ~ 55.2 to 124.3 initial stiffness modulus (Go) for un-cemented soils, in MPa 47 N60
Schnaid et al., 2004 ~ 124.3 to 331.5 initial stiffness modulus (Go) for cemented soils, in MPa 47 N60
Sandorni, 1991 20.6 operational stiffness modulus (E) for cemented soils, in MPa 47 N60
APPENDIX E
Sand
Materials
100.000
Input View
Stiff Clay
Sand
2
1
0.000
MSettle 7.3 : RoadWidth12.0m.sli
date
P.O. Box 69 Phone +31 15 269 35 00
2600 AB Delft Fax +31 15 261 08 21 30/10/2009
PGS Power Plant Nongsaeng
Road width 12.0 m.. Settlement Prediction
Height 5.0 m. Annex
Height 5.0 m.
Road width 12.0 m.. Settlement Prediction
PGS Power Plant Nongsaeng
Time-History
105.921730
105.921725
Loading [kPa]
105.921720
2600 AB Delft
P.O. Box 69
105.921715
0.000000
0.200000
+31 15 261 08 21
+31 15 269 35 00
Settlement [m]
0.400000
0.600000
0.800000
Annex
30/10/2009
1.000000
MSettle 7.3 : RoadWidth12.0m.sli
date
Time-History
2.633325
2.633320
Loading [kPa]
2.633315
2600 AB Delft
P.O. Box 69
2.633310
0.000000
+31 15 261 08 21
+31 15 269 35 00
0.100000
Settlement [m]
0.200000
0.300000
Annex
30/10/2009
0.400000
MSettle 7.3 : RoadWidth12.0m.sli
date
Sample Sheet
ASTM TESTING CO.,LTD. UNCONFINED COMPRESSION TEST
30.0
650 47.0 0.014 25.05 106 42.44 164.92 304.03
700 48.7 0.015 25.05 110 43.95 140.17 292.33 25.0
0.0
0 0.005 0.01 0.015 0.02 0.025
STRAIN, %
ASTM TESTING CO.,LTD. UNCONFINED COMPRESSION TEST
0.0
0 0.005 0.01 0.015 0.02 0.025
STRAIN, %
ASTM TESTING CO.,LTD. UNCONFINED COMPRESSION TEST
10.0
0.0
0 0.005 0.01 0.015 0.02
STRAIN, %
TABLE 2
Sample Sheet
ASTM TESTING CO.,LTD. ATTERBERG LIMITS TEST
Container Number B-27 B-28 B-59 B-21 A-67 A-22 A-3 Plasticity index Ip = Wl - Wp
Number of Blows 19 24 32 40
Wt. Wet Soil+Container gm. 40.950 38.860 35.530 30.950 21.560 21.540 19.580 Flow Index If = Slope of Flow Curve
Wt. Dry Soil+Container gm. 35.540 32.260 29.990 26.830 18.890 18.980 16.820
Wt. Water gm. 5.410 6.600 5.540 4.120 2.670 2.560 2.760 Toughness Index It = Ip / If
Wt. Container gm. 24.310 18.360 18.080 17.820 9.350 9.590 6.560
Wt. Dry Siol gm. 11.230 13.900 11.910 9.010 9.540 9.390 10.260
49.00
48.00
Water Content (%)
(Liquid Limit WL)
47.34
47.00
46.00
45.00
10 Number of Blows. 100
ASTM TESTING CO.,LTD. ATTERBERG LIMITS TEST
Container Number B-61 B-55 B-34 B-73 A-69 A-19 A-24 Plasticity index Ip = Wl - Wp
Number of Blows 18 24 32 40
Wt. Wet Soil+Container gm. 46.030 40.900 35.450 32.340 20.980 21.880 21.400 Flow Index If = Slope of Flow Curve
Wt. Dry Soil+Container gm. 39.210 35.750 30.190 27.990 18.880 19.520 19.110
Wt. Water gm. 6.820 5.150 5.260 4.350 2.100 2.360 2.290 Toughness Index It = Ip / If
Wt. Container gm. 24.210 24.170 18.050 17.710 9.570 9.500 9.450
Wt. Dry Siol gm. 15.000 11.580 12.140 10.280 9.310 10.020 9.660
46.00
45.00
Water Content (%)
(Liquid Limit WL)
44.27
44.00
43.00
42.00
10 Number of Blows. 100
ASTM TESTING CO.,LTD. ATTERBERG LIMITS TEST
Container Number B-44 B-24 B-17 B-19 A-36 A-46 A-62 Plasticity index Ip = Wl - Wp
Number of Blows 18 24 33 40
Wt. Wet Soil+Container gm. 44.750 40.710 35.320 33.040 21.490 18.170 18.280 Flow Index If = Slope of Flow Curve
Wt. Dry Soil+Container gm. 38.250 35.520 29.950 28.380 19.450 16.070 16.160
Wt. Water gm. 6.500 5.190 5.370 4.660 2.040 2.100 2.120 Toughness Index It = Ip / If
Wt. Container gm. 24.480 24.300 18.030 17.860 9.330 6.500 6.490
Wt. Dry Siol gm. 13.770 11.220 11.920 10.520 10.120 9.570 9.670
48.00
47.00
Water Content (%)
(Liquid Limit WL)
46.08
46.00
45.00
44.00
10 Number of Blows. 100
ASTM TESTING CO.,LTD. ATTERBERG LIMITS TEST
Container Number B-38 B-42 B-26 B-80 A-54 A-4 A-13 Plasticity index Ip = Wl - Wp
Number of Blows 18 24 33 40
Wt. Wet Soil+Container gm. 43.880 39.060 36.550 34.380 19.320 19.180 20.920 Flow Index If = Slope of Flow Curve
Wt. Dry Soil+Container gm. 36.740 33.570 30.290 28.590 16.550 16.400 18.350
Wt. Water gm. 7.140 5.490 6.260 5.790 2.770 2.780 2.570 Toughness Index It = Ip / If
Wt. Container gm. 24.160 23.680 18.730 17.670 6.510 6.540 9.430
Wt. Dry Siol gm. 12.580 9.890 11.560 10.920 10.040 9.860 8.920
57.00
56.00
Water Content (%)
(Liquid Limit WL)
55.34
55.00
54.00
53.00
10 Number of Blows. 100
ASTM TESTING CO.,LTD. ATTERBERG LIMITS TEST
Container Number B-52 B-48 B-43 B-25 A-9 A-47 A-74 Plasticity index Ip = Wl - Wp
Number of Blows 18 24 33 40
Wt. Wet Soil+Container gm. 40.170 36.050 34.100 33.690 18.630 18.410 19.670 Flow Index If = Slope of Flow Curve
Wt. Dry Soil+Container gm. 34.430 29.690 28.470 28.240 16.590 16.280 17.450
Wt. Water gm. 5.740 6.360 5.630 5.450 2.040 2.130 2.220 Toughness Index It = Ip / If
Wt. Container gm. 24.110 18.080 17.990 17.940 6.480 6.430 6.450
Wt. Dry Siol gm. 10.320 11.610 10.480 10.300 10.110 9.850 11.000
56.00
55.00
Water Content (%)
(Liquid Limit WL)
54.61
54.00
53.00
52.00
10 Number of Blows. 100
TABLE 3
SIEVE ANALYSIS
Sample Sheet
ASTM TESTING CO.,LTD. SIEVE ANALYSIS (ASTM D-422)
Sample : BH-1 Tested by: Lamprai Sample : BH-1 Tested by: Lamprai
Location : Bangkla Chachoengsao Date of Test: 11-6-52 Location : Bangkla Chachoengsao Date of Test: 11-6-52
Depth,m : 8.00-12.45 Water Content,% : Depth,m : 12.45-15.45 Water Content,% :
Before Washing(Sieve No.200) After Washed and Oven Dry Before Washing(Sieve No.200) After Washed and Oven Dry
Wt.Cont.+Dry Soil,gm 445.71 Wt.Cont.+Dry Soil,gm 170.02 Wt.Cont.+Dry Soil,gm 313.06 Wt.Cont.+Dry Soil,gm 79.44
Wt.Container,gm 65.45 Wt.Container,gm 65.45 Wt.Container,gm 67.37 Wt.Container,gm 67.37
Wt.Dry Soil,gm 380.26 Wt.Dry Soil,gm 104.57 Wt.Dry Soil,gm 245.69 Wt.Dry Soil,gm 12.07
Wt.Dry Soil,gm 380.26 Washing Loss,gm 275.69 Wt.Dry Soil,gm 245.69 Washing Loss,gm 233.62
Sieve Sieve Wt.Soil Adj.Wt. Wt.Soil Cumulative Percent Sieve Sieve Wt.Soil Adj.Wt. Wt.Soil Cumulative Percent
Size Opening Retain Soil Ret. Retain Soil Ret. Finer Size Opening Retain Soil Ret. Retain Soil Ret. Finer
mm. gm gm % % % mm. gm gm % % %
1 in. 25.40 1 in. 25.40
3/4 in. 19.05 3/4 in. 19.05
1/2 in. 12.70 1/2 in. 12.70
3/8 in. 9.53 3/8 in. 9.53
# 4 4.75 17.87 17.81 4.68 4.68 95.32 # 4 4.75 0.39 0.38 0.15 0.15 99.85
# 10 2.00 25.11 25.02 6.58 11.26 88.74 # 10 2.00 1.46 1.42 0.58 0.73 99.27
# 20 0.85 12.50 12.46 3.28 14.54 85.46 # 20 0.85 3.84 3.75 1.53 2.26 97.74
# 40 0.42 8.16 8.13 2.14 16.68 83.32 # 40 0.42 2.50 2.44 0.99 3.25 96.75
#100 0.15 16.03 15.97 4.20 20.88 79.12 #100 0.15 2.44 2.38 0.97 4.22 95.78
#200 0.075 25.12 25.03 6.58 27.46 72.54 #200 0.075 1.71 1.67 0.68 4.90 95.10
Pan 0.14 0.14 72.54 100.00 Pan 0.02 0.02 95.10 100.00
Total 104.93 104.57 Weighted Error,% -0.09 Total 12.36 12.06 Weighted Error,% -0.12
60 Sample No.1
50
Sample No.2
40
30 Sample No.3
20
Sample No.4
10
0
100.00 10.00 1.00 0.10 0.01
Diameter in Milimeter
60 Sample No.1
50
Sample No.2
40
30 Sample No.3
20
Sample No.4
10
0
100.00 10.00 1.00 0.10 0.01
Diameter in Milimeter
Consolidation Test
Sample Sheet
CONSOLIDATION TEST (ASTM D 2435) ASTM TESTING CO., LTD.
PROJECT : POWER GENERATION SUPPLY BORING NO. : BH-2R
0.85
SAMPLE NO. :
LOCATION : NONGSAENG SARABURI DEPTH (m) : 01.50-02.00 Cr = 0.058
0.80 Cc = 0.292
TESTED BY : RAWAT K.
Cs = 0.041
DATE : 29/09-02/10/2009 'vm
SOIL DESCRIPTION : STIFF CLAY MADE BY : M. SUKMOL 0.75
Applied Scale Final Cumulative Initial Water Content, Wni 27.62 %
Pressure Load Dial Reading Dial Change Final Water Content, Wnf 22.80 %
Void Ratio, e
0.70
(t/m ) (kg) (0.0001") h, (cm) Initial Void Ratio, e0 0.807
0.00 0.000 0 0.0000 Initial Total Unit Weight, ti 1.92 t/m
0.65
2.50 0.650 40 0.0102 Final Total Unit Weight, tf 2.05 t/m
5.00 1.300 100 0.0254 Specific Gravity, Gs 2.689
10.00 2.600 235 0.0597 Liquid Limit, LL - % 0.60
(cm2/sec)
Applied Sample Void Void Ratio Ave. Sample Fitting Time Cv (0.0001 cm/sec) Coef. of Permea
10
Pressure Height Height e = Hv/Hs Height t90 t50 0.848 x Ha 0.197 x Ha k x 10-8 (cm/sec)
(t/m2) H, (cm) Hv, (cm) Ha, (cm) (sec) (sec) 4 x t90 4 x t50 t90 t50
0.00 2.5200 1.1255 0.8071
2.50 2.5098 1.1153 0.7998 2.5149 1109 420 12.086 7.417 1.949 1.196
5.00 2.4946 1.1001 0.7889 2.5022 1815 702 7.313 4.393 1.769 1.063
1
10.00 2.4603 1.0658 0.7643 2.4775 1622 558 8.020 5.417 2.183 1.474
10
20.00 2.4082 1.0137 0.7269 2.4343 821 348 15.294 8.386 3.160 1.733
APPLIED SCALE FINAL DIAL CUM. DIAL SAMPLE HEIGHT VOID HEIGHT VOID RATIO AVERAGE FITTING TIME COEF. OF CONSLIDATION
PRESSURE LOAD READING CHANGE H = H0-h Hv = H-Hs e = Hv/ Hs SAMPLE HEIGHT (min) CV, (0.0001 cm2/sec)
(t/m2) (kg) (0.0001 in) h, (cm) (cm) (cm) Hav, (cm) t90 t50 0.848 x Ha2 0.197 x Ha2
4 x t90 4 x t50
0.00 0.000 0 0.0000 2.5200 1.1255 0.8071
2.50 0.650 40 0.0102 2.5098 1.1153 0.7998 2.5149 18.49 7.00 12.086 7.417
5.00 1.300 100 0.0254 2.4946 1.1001 0.7889 2.5022 30.25 11.70 7.313 4.393
10.00 2.600 235 0.0597 2.4603 1.0658 0.7643 2.4775 27.04 9.30 8.020 5.417
20.00 5.201 440 0.1118 2.4082 1.0137 0.7269 2.4343 13.69 5.80 15.294 8.386
40.00 10.401 688 0.1748 2.3452 0.9507 0.6818 2.3767 22.09 6.90 9.036 6.720
80.00 20.803 995 0.2527 2.2673 0.8728 0.6258 2.3063 33.64 13.00 5.587 3.358
160.00 41.606 1480 0.3759 2.1441 0.7496 0.5375 2.2057 21.16 7.10 8.124 5.624
40.00 10.401 1360 0.3454 2.1746 0.7800 0.5594 2.1593
10.00 2.600 1178 0.2992 2.2208 0.8263 0.5925 2.1977
2.50 0.650 1072 0.2723 2.2477 0.8532 0.6118 2.2343
datamain\labtest\conso\Lab ConsoBH-2
TABLE 7
Sample Sheet
Field Permeability Test
(Constant Head)
PROJECT: SIAM ENERGY POWER PLANT DATE :09 June 2009
Sample sheet
SOIL RESISTIVITY TEST
ASTM TESTING CO.,LTD.
TEST NO: R-1
1
Distance (m)
2 E-W
3
4
N-S
5
Average
6
0 20 40 60 80 100 120 140 160 180 200
Ground Resistivity (-m)
Note:
N The apparent soil resistivity is then given by
=2aR (-m)
N where:- = ground resistivity in -m
= 3.1415927
a = electrode spacing in metres
R = measured resistance in at spacing 'a'
R-1
Inspector: Satit
E Project Engineer: Suchat
Project Manager: Weraphol
Project Owner: i-ASTM
Table 9
Sample sheet
Summary of Seismic waves travel time and velocityof the site
Saraburi B CoGeneration
2,500
2,000
1,500
Shear Wave
Compression Wave
1,000
Velocity(m./sec.)
500
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Depth(m.)
Dynamic Elastic Moduli (BH-03) : SBC
G = Shear modulus, MPa v = Poisson's ratio E = Young modulus, MPa K = Bulk modulus, MPa
2
Depth (m) G = UVs g v = (0.5-VR^2)/(1-VR^2) E = 2G.(1+v) K = UVp2g
1.0
190 0.27 480.85 59.72
2.0
270 0.28 692.25 88.63
3.0
303 0.33 808.26 121.24
4.0
367 0.35 988.39 157.30
5.0
402 0.34 1076.88 164.62
6.0
626 0.30 1623.52 216.95
7.0
668 0.36 1812.06 300.27
8.0
1161 0.34 3102.32 470.61
9.0
1257 0.34 3358.68 509.28
10.0
1422 0.31 3716.51 509.63
11.0
1252 0.29 3226.50 421.65
12.0
1589 0.33 4219.86 621.22
13.0
1408 0.33 3730.73 543.16
14.0
1569 0.34 4192.20 634.81
15.0
2406 0.31 6302.00 872.85
16.0
1614 0.34 4320.02 660.66
17.0
2011 0.35 5446.42 890.40
18.0
2011 0.34 5389.83 829.76
19.0
2451 0.32 6458.94 935.02
19.4
2053 0.32 5425.31 779.48
Table 10
Sample sheet
DUTCH CONE
ASTM TESTING CO.,LTD.
TEST NO. DC-1 (SBC)
PROJECT : Saraburi B Cogeneration Company Limited TEST NO. : DC-1 TESTED BY : Phisit
0 0 0
1 1 1
2 2 2
3 3 3
4 4 4
5 5 5
6 6 6
7 7 7
8 8 8
9 9 9
DEPTH (m)
DEPTH (m)
DEPTH (m)
10 10 10
11 11 11
12 12 12
13 13 13
14 14 14
15 15 15
16 16 16
17 17 17
18 18 18
19 19 19
20 20 20
0 1 2 3 4 5 0 20 40 60 80 100 0 5 10 15 20
2 2
Qc ( x1000 t/m ) Qs (t/m ) Qs/Qc (%)
Table 11
Sample sheet
COMPACTION TEST(ASTM D1140 - 54) ASTM TESTING CO.,LTD.
MOLD NO. 4 4 4 4
B. WATER CONTENT
CONTAINER NO. A-29 A-30 A-26 A-37
C. RESULTS
MAX. DRY DENSITY, MDD (t/m) = 2.137 OPT. MOISTURE CONTENT, OMC (%) = 9.40
2.2
2.1
2.0
Dry Density (t/m)
1.9
1.8
1.7
1.6
5 6 7 8 9 10 11 12 13 14 15
TP-1 DATAMAIN\LABTEST\COMPACTION\Compaction-Silaporn-15-05-2010.xls
ASTM D 1883 / AASHTO T 193 / .-. 109 (DH-T 109)
. . DATE : 20/05/2553
DATE : 21/05/2553
1. COMPACTION DATA (BEFORE SOAKING) TEST NO. 1 TEST NO. 2 TEST NO. 3
NO. OF LAYER 5 5 5
3. SWELLING MEASUREMENT
DATE TIME ELAPSED TIME GAGE RDG. % SWELL GAGE RDG. % SWELL GAGE RDG. % SWELL
4. PENETRATION TEST
PENETRATION LOAD, R PRESSURE LOAD, R PRESSURE LOAD, R PRESSURE
0.000 0 0 0
LOAD (lbs) = 1.0305R - 70.404 (R = Guage Reading in division, 0.0001 in/div) PISTON AREA (sq.in) = 3.040
DATAMAIN\LABTEST\LAB CBR\CBR-Silaporn-19-02-2010.xls
ASTM D 1883 / AASHTO T 193 / .-. 109 (DH-T 109)
% CBR
TEST NO. 1 2 3
STANDARD UNIT LOAD,B (psi) 1,000 1,500 1,000 1,500 1,000 1,500
1000
12 BLOWS/LAYER
900 25 BLOWS/LAYER
56 BLOWS/LAYER
800
700
PISTON PRESSURE (psi)
600
500
400
300
200
100
0
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
PENETRATION (in)
DATAMAIN\LABTEST\LAB CBR\CBR-Silaporn-19-02-2010.xls
ASTM D 1883 / AASHTO T 193 / .-. 109 (DH-T 109)
DATE : 20/05/2553
DATE : 21/05/2553
TEST NO 1 2 3
2.50
2.45
2.40
2.35
2.30
2.25
2.20
2.15
2.10
2.05
DRY DENSITY (t/m)
2.00
1.95
1.90
1.85
1.80
1.75
1.70
1.65
1.60
1.55
1.50
1.45
1.40
5.0 15.0 25.0 35.0 45.0
CBR (%)
DATAMAIN\LABTEST\LAB CBR\CBR-Silaporn-19-02-2010.xls
Table 12
Sample sheet
GROUND WATER QUALITY ANALYSIS REPORT
Coordination : INFRATECH ASIM CO., LTD.
Sampling Source : Saraburi B Cogeneration Co., Ltd. (Saraburi)
Monitoring Date : February 25, 2010
Monitored by : Health & Envitech Co., Ltd.
Report Date : March 6, 2010
Ref. No. : H.E. 371/2010
... ...
(Prasart Chiaplaem) (Rung Rittiyan)
Laboratory No. -152--3213 Laboratory No. -152--3214
GROUND WATER QUALITY ANALYSIS RESULTS
STARDARD
DETECTED
SOURCE PARAMETER UNIT Suitable Max.
VALUE
allowance allowable
Saraburi B Cogeneation Co., Ltd. pH - 6.7 7.0 8.5 6.5 9.2
Calcium (Ca) mg/l 0.186 - -
Magnesium (Mg) mg/l 2.400 - -
Manganese (Mn) mg/l *2.234 d 0.3 d 0.5
Chloride (Cl) mg/l 42 d 250 d 600
Total Hardness (as CaCO3) mg/l 152 d 300 d 500
Iron (Fe) mg/l *2.421 d 0.5 d 1.0
Potassium (K) mg/l 0.038 - -
Sodium (Na) mg/l 1.502 - -
Nitrate (NO3) mg/l 0.280 d 45 d 45
Sulfate (SO4) mg/l 4.276 d 200 d 250
Carbon dioxide (CO2) as
mg/l 253 - -
Carbonate (CO3)
Phosphate (PO4) mg/l 4.276 - -
Silica (Si) mg/l 35.783 - -
*Over standard limit
Remark
1. Standard: Notification of the Ministry of Natural Resources and Environment B.E. 2551 (2008), issued under The
Ground Water Act B.E. 2520 (1977), published in the Royal Government Gazette, Vol. 125, Special Part 85 . dated May 21, B.E.
2551 (2008).
2. Test results will be applicable only for the brought samples.
3. Do not copy partial of this analysis report without official approval.
4. Definition
mg/l : milligrams per liter
... ...
(Prasart Chiaplaem) (Rung Rittiyan)
Registered Lab. Controller Managing Director
Laboratory No. -152--3213 Health & Envitech Co., Ltd.
Registered Lab No. -152