Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
LCD-DV Troubleshooting
32" Class HD 720P
LCD TV (31.5" diagonally)
Preliminary
y Section:
Contact Information, Preliminary Matters, Specifications,
LCD Overview, General Troubleshooting Steps,
Signal Distribution, Disassembly Instructions and Voltages
Disassembly Section: Removal of Circuit Boards
Troubleshooting Section: Board Operation Troubleshooting of :
Switch Mode Power Supply
Ballast (Backlight Driver)
Main Board
Ft Control Board
Key Board
Speakers
Section 1
This Section will cover Contact Information and remind the Technician of Important
Safety Precautions for the Customers Safety as well as the Technician and the
Equipment.
Basic Troubleshooting Techniques which can save time and money sometimes can
be overlooked. These techniques will also be presented.
This S
Thi Section
ti willill gett the
th Technician
T h i i familiar
f ili with
ith the
th Disassembly,
Di bl Identification
Id tifi ti and
d
Layout of the LCD Display Panel.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for
g
diagnosis or test p
purposes,
p , disconnect the p
power immediately y after p
performing
g the necessaryy checks. Also be
aware that many household products present a weight hazard. At least two people should be involved in the
installation or servicing of such devices. Failure to consider the weight of an product could result in physical
injury.
Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage
the electronics in a manner that renders them inoperative or reduces the time until their next failure.
Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively,
you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before
removing a replacement part from its package, touch the anti
anti-static
static bag to a ground connection point or
unpainted metal in the product. Handle the electronic control assembly by its edges only. When
repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory
l Information
f
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed g to p
provide reasonable p
protection against
g harmful
interference when the equipment is operated in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception
reception, which can be determined by turning the equipment off and on on, the user is
encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate
the receiving antenna; Increase the separation between the equipment and the receiver; Connect the
equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the
dealer or an experienced radio/TV technician for help.
LCD-DV: 32LD350,
32LD350 32LG40
32LG40, 32LH30
32LH30, 37LH55
37LH55, 42LG60
42LG60, 42LG70
42LG70, 42LH20
42LH20, 42LH40
42LH40, 42LH50
42LH50, 42LH90
42LH90,
42SL80, 47LG90, 47LH85, 42LE5500, 42LX6500 (3D), 47LX9500 (3D), 55LX6500 (3D)
42PG20, 42PJ350, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK250, 50PK750, 50PS80, 50PK950,
PLASMA: 50PS60, 60PK750, 60PK950, 60PS11, 60PS60, 60PS80
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical
damage and part number accuracy.
2 Check the model label
2. label. Verify model names and board model matches
matches.
3. Check details of defective condition and history. Example: Oscillator failure dead set, etc
Define Look at the symptom carefully and determine what circuits could be causing
the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and
check for possible overheated components. Capacitors will sometimes leak dielectric material
and give off a distinct odor
odor. Frequency of power supplies will change with the load
load, or listen for
relay closing etc. Observation of the front Power LED may give some clues.
Localize After carefully checking the symptom and determining the circuits to be
checked and after giving a thorough examination using your senses the first check should
always be the DC Supply Voltages to those circuits under test. Always confirm the supplies
are not only the proper level but be sure they are noise free. If the supplies are missing check
the resistance for possible short circuits.
Isolate To further isolate the failure, check for the proper waveforms with the
Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing
and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes
glitches
glitches or road
road bumps
bumps will be an indication of an imminent failure
failure.
Correct The final step is to correct the problem. Be careful of ESD and make sure to
check the DC Supplies for proper levels. Make all necessary adjustments and lastly always
perform a Safety AC Leakage Test before returning the product back to the Customer.
Customer
Key TV Features
High Definition Resolution
70,000:1
70 000 1 D Dynamic
i CContrast
t tRRatio
ti
Picture Wizard II (Easy Picture Calibration)
Smart Energygy Savingg
AV Mode (Cinema, Sports, Game)
Clear Voice II
ISFccc Ready
24P Real Cinema
2 HDMI 1.3 Inputs
SIMPLINK Connectivity
C ti it
Dolby Digital 5.1 Decoder
Infinite Sound
Picture Wizard
Get easy self-calibration with on-screen reference points for key picture
quality elements such as black level, color, tint, sharpness and
backlight levels. Take the guesswork out of picture adjustments with
this simple-to-use feature. It's not actuallyy magic,
g but it will sure seem
that way.
Enjoy a true cinema-like experience in your own home with movies the way
they are meant to be seen. LG's Real Cinema technology displays 24p source
f
frames
LGs ISFccc Ready HDTVs contain the detailed standards necessary for
professional calibration of brightness, contrast, tint, sharpness, color levels and
much more to meet local lighting conditions for both day and nighttime viewing.
Settings are added to preset modes for easy access from your LG remote.
LG SimLink is a brand specific type of HDMI CEC which allows you to control
multiple HDMI components through a single television remote.
To see it real is to hear it real. LG's Infinite Sound, which is tuned by the well-
known sound specialist Mr. Mark Levinson, enhancements your y g
High
definition TV experience with maximum surround sound.
p/n AKB72915206
MKJ39170828
105-201M
USB 1
HDMI 2
Head
Phones
MAIN BOARD
Rear and Side
Input/Output locations Component
Inputs
Software
Version
found on the
USB Flash
Drive
File found
on the USB
Flash Drive
Model Name : 32LD350-UB (Liquid Crystal Display) Parental Control : Channel is not blocked
Memory DVI/HDMI Status
FLASH : 16384 KB Cant display this information now
DRAM : 131072 KB
NVM : 64 KB
Host Release Version
Firmware Version(MP) : 3.05.00(0.1.58.22) Software Version
Micom Version : 3.02
Compile Date & Time : 20100126 & 08:56:56
Compile User : jh.jung Channel Frequency
FAT Status (Main)
Center Frequency : 663.00 MHz
PCR lock : Locked Program Clock Reference (Locked or No)
Modulation mode : QAM 256 Channel Type (8VSB, QAM 64, 256)
Carrier lock status : Locked Channel (Locked or No) 8VSB (Above 20 is good)
QAM 64 (Above 24 is good)
SNR : 36 dB Channel Signal to Noise Ratio QAM 256 (Above 30 is good)
Signal level : 99 dBmV Channel Signal Level (Above 80dBmV good)
Current Channel (Main)
1) Press ADJ key on the 2) Scroll down to Item 8 EDID D/L 3) Opening EDID D/L screen
Service Remote. and press the Select Key. appears.
31-1/2"
Wattage 800mm 2-7/8"
AVG: 110W 73.66mm
STBY: <1W
11-3/4"
7-7/8" 6-5/16"
298mm
200mm 160mm
Model No.
Serial No.
3-15/16"
Side Label
22-3/16" 100mm
563.88mm Center
20"
508mm
10" 11 1/8"
254mm 281.78mm
2-3/16"
55.56mm
8-1/8"
15-3/4" 205.74mm
Weight without Stand: 24.3 lb
400mm
Weight with Stand: 27.6 lb
Disassembly:
This section of the manual will discuss Disassembly, Layout
(Ci it Board
(Circuit B d Identification)
Id tifi ti ) off the
th 32LD350 LCD Di Directt Vi
View T
Television.
l i i
Remove the 20
Putting in an
screws indicated.
improper screw
Pay attention to
when
th size
the i and d ttype
reassembling
of screw
may Cause
as there are many
damage.
different types.
The Stand does not have to be removed before removing the back.
Warning:
g The Frame may
y
Panel Interface Board have sharp edges
Ballast
LVDS Cable
Power Supply
P S l
(SMPS)
M i Board
Main B d
Keyboard
AC Input
Ballast
P203 P201
CN1 POWER
P802
SUPPLY P402
MAIN
SMPS Used in the 32LD350: BOARD
EAY60868901 32LD350 AUSWLJR or
AUSDLFR or AUSDLUR or AUSDLJR Main Boards Used in the 32LD350:
EBU60850009 32LD350 AUSWLJR and AUSDLFR
EAY60869101 32LD350 CUSWLH or EBR66049702 32LD350 AUSDLJR
CUSDLH or CUSWLHO EBU60850010 32LD350 AUSDLUR
EBU60850003 32LD350 CUSDLH
Key EBU61005102 32LD350 CUSWLH and CUSWLHO
Board
p/n: EBR65863602
AC In
J2
P3000
J1
P201
Disconnect
P201, P203
and AC In
SK100. Press in gently on
the two tabs
to release lock
P802
Decorative
Remove decorative N/C Metal Plate
plastic and remove the
board. After removing the Main, there
P600 P2401 are tabs sticking through the
Main board holding the Metal
plate in place.
NOTE: Always check on
top and behind the Large
ICs. And look for a piece
of Chocolate Main Boards Used in the 32LD350:
(Heat Transfer Material). EBU60850009 32LD350 AUSWLJR and AUSDLFR
Be sure to transfer to EBR66049702 32LD350 AUSDLJR
new Board if present
present. EBU60850010 32LD350 AUSDLUR
EBU60850003 32LD350 CUSDLH
EBU61005102 32LD350 CUSWLH and CUSWLHO
Use caution
caution, do not allow screws to fall.
fall
CN1
Backlight
connector
Cushion
pieces behind
the Inverter
J2
Troubleshooting: g
This section of the manual will discuss troubleshooting.
EAY60869101
32LD350 CUSWLH or CUSDLH or CUSWLHO
Cold Gnd
Hot Gnd
F501
3.15A/250V
STBY 0V
Run 388V
From Hot Gnd
Hot Ground
F100 Shock
5A/250V Hazard
AC Protect
To Backlights
a d
Rectifier r a
y r POWER SUPPLY (SMPS) INV
Inverter On
y
7 On
Starts the Ballast.
Stand 12V/24V Backlights Light.
By 3.5V Reg Regulators BR1 Fixed
No AC Det
Analog Dimming Manipulates Backlights
in this model 5 7 8
Stand By 12V 24V
T-CON Inside Panel
3.5V 12V LVDS
POWER
At point 3 TV is in Along with Video
_ON INV
Stand-By state. On LVDS cable
Energy Star compliant. On
Less than 1 Watt 2 5 5 5 7
12V 6
Q402 8 8
MAIN Audio_AMP
BOARD IC600 PWM-DIM
Q401 5V_USB Q405 Digital Dimming
IC401 1.8V_AMP Manipulates Backlight Brightness
2 IC601
Power On
The Backlights should turn on at this point. If the 24V and the Inverter On command is arriving at the
Ballast, but no backlights, then see Ballast Section for further testing.
(B) Remove AC power and Remove Jumper. SMPS and Ballast are OK.
6-10
6 10 GND Gnd Gnd Gnd
(1)
11 ERROR 0V 0.59V Open
(2)
12 INV_ON 0V 3.31V Open
(3)
13 A-DIM n/c 4.5V Open
14 (4)
P-DIM 0V 0.65V~3.25V Open 1
(1) Error Pin 11 (To P201 pin 20 Silk Screened A-DIM) Goes high when the backlights are told to come on. Goes
back low when they come on. If it goes high again on the 5th attempt to fire the backlights, the set shuts off.
(2) INV_ON Pin 12 (From P201 pin 18) Turns on the Backlights.
(3) A-DIM Pin 13 (From P201 pin 22 Silk Screened PWM-DIM) Is not used.
(4) PWM-DIM Pin 14 (From P201 pin 24 Silk Screened Error_Out) can vary according to incoming video IRE level
and OSD Backlight setting Output from the Video Processor IC100. Range 0.65V to 3.25V.
F501
Bottom
Left of F100
F501
SMPS
3.15A/250V
F100 L N
From Hot Gnd
5A/250V
STBY 0V
AC IN
Run 388V
N
L
SK100
If reading
di ththe voltage
lt on F501 right
i ht after
ft
power off, it takes a very long time to
F100 (Diode Check) bleed down to the reading given here.
Red or Black Lead on Fuse (Open)
Other Lead on Hot Ground
Bottom Half
CN1
24V
Fuse
6 7 8 9 10 9 10 11 12 3.5V_ST
Q402
Q401
PWR E5 RL-ON
1 1 24V Controller 1 1
3.41V
2 2
24V Error Normal is Low. But
24V 3 3 Reg 12V when the backlights are
Reg 17 19 21 12V 11.97V
4 4 told to fire via INV_ON,
this line goes high. When
5 5 2 3 4 24V 24.19V they fire, it goes back low.
If they fail to light after 5
attempts, the set shuts off.
ERR 0.59V
ERR 11 11 20 20 E5 Error
PWM-DIM
PWM-DIM 14 14 24 24 AB12 PWB-2
A-DIM
BR1 13 13 22 22 n/c
4.49V
VBR-B (PWM Diming) Manipulates the Backlight Brightness via Customers OSD.
Manipulates the Backlight Brightness via the BCM Chip. Darker Picture, Darker
Backlights to facilitate improved Contrast Ratio. 0.65V ~ 3.25V Range
1
Pin 2 at 2MSec per/div Pin 3 at 2MSec per/div
Q103 Q107
Q109 Q101 3
2
Pin 1 24.16V
Pin 2 9.03V
Pin 3 0V
30V p/p
/ 80% PWM-DIM
PWM DIM 15 15V p/p
15.15V / 80% PWM-DIM
PWM DIM
CN1
F1 (Diode
(Di d Mode
M d Check)
Ch k)
Open (Red Lead on Fuse)
0.9V (Black Lead on Fuse)
F101
7A
(1) P-DIM
Pin 14. PWM_DIM can vary according to OSD Backlight setting and the
incoming video IRE level. PWM-DIM is Output from the Video Processor IC100.
Range 0.65V to 3.25V.
(3) ERRORPin 11. Normal low. Goes high when the Backlights are told to turn on by
INV_ON. After backlights fire, go back low. Will repeat 5 times then shut off the set.
USB
IC100
HDMI
Headphones
RS232
HDMI
PC Optical
PC Side
Audio Audio
Composite
TUNER Inputs
P600 P2401 To
EBU60850003 32LD350 CUSDLH (The one shown)
To Speakers Front IR
EBU60850009 32LD350 AUSWLJR and AUSDLFR
EBR66049702 32LD350 AUSDLJR
EBU60850010 32LD350 AUSDLUR
EBU61005102 32LD350 CUSWLH and CUSWLHO
L415
IC403 P802
IC401
P402 IC407
IC2 L406
L423 IC105 IC1000
SW100
Microprocessor
MAIN BOARD
Reset
p/n: EBU60850003
L422
IC1450
IC1
IC100 Mstar IC101 Q100
IC406 Micro and Video E
USB1
L421 C
Processor B
HDMI
IC1004
IC405
Q7702
X100 B
X1005 C
E Headphone
C
D7705 12MHz Q1100 Q1104 B E
A1 A2 C C D1100 25MHz C
IC600 C B E
C B E B E
Q1105 A2 A1 Q1103
Digital Video 18. IF p
17. IF n
16. IF AGC
JK7700 15. Reset
TUNER 14. 3.3V
L607 L606 TDVJ-H001F 13. 1.26V IC5001
12. GND
3
Analog Video 11. CVBS
SIDE A/V
2 2
10. NC 1
JK1104 JK1102 Audio 9. SIF
JK1103 JK9800
8. NC
Tuner Data 7. SDA
Tuner Clock 6. SCL
5. NC
P600 4. NC
Tuner B+ 3. 5V
2. NC
1. NC
P2401
R-R+L-L+
Main Boards Used in the 32LD350: Main Boards Used in the 32LD350:
EBU60850009 32LD350 AUSWLJR and AUSDLFR EBU60850003 32LD350 CUSDLH
EBR66049702 32LD350 AUSDLJR EBU61005102 32LD350 CUSWLH and CUSWLHO
EBU60850010 32LD350 AUSDLUR
Q407
Q406 B
B E C
E C
S G
Q409
D
3
Q402 C
2 1 Q405 B E
C
Q401 B E
3
2 1
1 2 IC408
IC103 3
IC104
In
D7706 IC601
A2 2
A1 C
A1 A2
D7703 D102
C
C E IC1100 C A1
Q1101 B B DS
A2 B
E C E C Q600
Q1102 C B
E
G B
Q7701 Q7703
IC7701
Q5004 IC1201
C
B E
IC1104
IC1105
A1 A2
D1115 C E BE B
Q2405 Q2406
C C
IC103 Reset IC1100 Earphone IC1201 RS232 IC7702 EDID Data Q1101-2 EARPHONE
Pin Generator Pin Amp Pin Data Buffer Pin HDMI4 Pin MUTE
[1] Gnd [1] 2.14V [1] 3.34V [1] 0V (Gnd) B 0V
[2] 0V [2] 0V (Gnd) [2] 3.48V [2] 0V (Gnd) C 0V
[3] 3.39V [3] 0.02V [3] 0V [3] 0V (Gnd) E Gnd
[4] 2.19V [4] 0V [4] 0V (Gnd)
IC104 EEPROM [5] 2.19V [5] (-5.37V) [5] 4.69V Q2405 IR Buffer
Pin Mstar [6] 4.37V [6] 5.39V [6] 4.69V Pin 1st Driver
[1] 0V (Gnd) [7] 2.19V [7] (-5.37V) [7] 4.69V B 0.6V
[2] 0V (Gnd) [8] 2.18V [8] n/c (0V) [8] 4.69V C 0V
[3] 0V (Gnd) [9] n/c (3.39V) E Gnd
[4] 0V (Gnd) IC1104 Optical Audio [10] n/c (3.35V) Q401 Power On/Off
[5] 3.31V Pin Amp [11] n/c (0V) Pin Driver for Q402 Q2406 IR Buffer
[6] 3.31V [1] 1.64V [12] 3.35V B 0.64V Pin 2nd Driver
[7] 0V (Gnd) [2] 3.29V [13] 0V C 0V B 0V
[8] 3.31V [3] 0V (Gnd) [14] 5.47V E Gnd C 3.3V
[4] 0V (Gnd) [15] 0V (Gnd) E Gnd
IC400 (+3.3V_AVDD_MPLL) [5] 3.29V [16] 3.37V Q402 Power On/Off
Pin Regulator Pin Switch Q5004 Tuner SIF
[In] 3.35V IC1105 EDID Data IC7701 EDID Data 1 3.39V (In) Pin (Sound) Buffer
[Gnd] Gnd Pin PC Pin HDMI2 2 0.89V (Ctl) B 0.163
[Out] 3.34V [1] 0V (Gnd) [1] 0V (Gnd) 3 3.28V (Out) C Gnd
[2] 0V (Gnd) [2] 0V (Gnd) E 0.85V
IC408 Power_Det [3] 0V (Gnd) [3] 0V (Gnd) Q405 Inverter On/Off
Pin 24V, 12V, 3.5V [4] 0V (Gnd) [4] 0V (Gnd) Pin Switch Q7701 HDMI 2
[1] 3.52V [5] 4.7V [5] 4.7V B 0.06V Pin Det
[2] 3.35V
3 35V [6] 4.7V
4 7V [6] 4.7V
4 7V C 3.32V
3 32V B 0.63V
0 63V
[3] Gnd [7] 4.7V [7] 4.7V E Gnd C 0V
[8] 4.7V [8] 4.7V E Gnd
IC601 (+1.8V_Amp)
Pin Regulator Q407 PANEL_VCC Q409 PANEL_VCC Q600 AMP_MUTE Q7703 CEC Remote
[1] Gnd Pin Control 2nd Driver Pin Switch Pin Pin 25 IC600 Pin HDMI CEC
[2] 1.81V B 0.68V S 11.97V (In) B 0.08V [B] 3.39V
[3] 3.31V C 0V G 1.84V (Enable) C 3.35V [G] 3.32V
E Gnd D 11.97V (Out) E Gnd [S] 0V
Q406 PANEL_VCC [D] 3.26V
Pin Control 1st Driver D102 Mute D1115 5V Routing
B 0.05V Pin Routing Pin for IC7705 D7703 3.5V Blocking D7706 5V Routing
C 0.68V [A1] 0V [A1] 0.03V Pin for Q7703 Pin for IC7702
E Gnd [A2] 0V [A2] 0V [A1] 0V [A1] 4.98V
[C] 0V [C] 4.69V [A2] 3.37V [A2] 0V
[C] 3.3V [C] 4.69V
X100 X1005
X100 X1005
MAIN Board
P802
12V_LVDS
Pins 27~30
N t Th
Note: The Panel
P l has
h an additional
dditi lb
board
d th
thatt sets
t on ttop and
d ttakes
k ththe
12V to generate the 5 usable voltages for the Panel.
The waveforms
represent the 10 bit
Differential Pair LVDS
Signal.
All waveforms shown
are the (+) part of the
differential pair.
The (-) part is exactly
the same only
inverted.
inverted
All waveforms are at
the same 5uSec
per/div rate and
100Mv per/div.
Diode Diode
Pin Label Run Pin Label Run
Check Check
1 Gnd Gnd Gnd 16 TXA1- 0.79V Gnd
2 Gnd Gnd Gnd 17 Gnd Gnd Gnd
3 N/C n/c n/c 18 TXA0+ 0.79V Gnd
4 N/C n/c n/c 19 TXA0- 0.79V 1.06V
5 Gnd Gnd Gnd 20 Gnd Gnd Gnd
6 TXA3+ 1.14V 0.79V 21 N/C n/c n/c
7 TXA3- 1.34V 0.79V 22 LVDS_Sel 2.42 Open
8 Gnd Gnd Gnd 23 Gnd Gnd Gnd
9 TXAC+ 1.25V 0.79V 24 Gnd Gnd Gnd
10 TXAC- 1.2V 0.79V 25 Gnd Gnd Gnd
11 Gnd Gnd Gnd 26 Gnd Gnd Gnd
12 TXA2+ 1.16V 0.79V 27 Panel_VCC 11.97V 2.59V
13 TXA2- 1.35V 0.79V 28 Panel_VCC 11.97V 2.59V
14 Gnd Gnd Gnd 29 Panel_VCC 11.97V 2.59V
15 TXA1+ 1 15V
1.15V 0 79V
0.79V 30 Panel VCC
Panel_VCC 11 97V
11.97V 2 59V
2.59V
1 SPK-R(-)
SPK R( ) 0V 12 95V
12.95V Open
2 SPK-R(+) 0V 12.95V Open
3 SPK-L(-) 0V 12.95V Open
4 SPK-L(+) 0V 12.95V Open
(1)
P600
Circuit Location
on the Main Board
R- R+ L- L+
The IR board (located on the bottom left as viewed from the rear) contains the IR (Infrared) Remote
Sensor and Power LEDs. This board also connects to the Key Board.
The IR (Infrared) remote receiver can be measured (2V) at pin 9 of connector J1 or P2401 on the Main
board in Stand-By. During run pin 9 reads (1.98V).
The IR pulses (1.6V p/p) J1 pin 9 are sent to P2401 on the Main board and on to the Microprocessor
(IC100) via pin C4.
The Front Power LEDs are controlled by pins 8 (Blue LED) and 12 (Red LED) of J1.
The Key
Th K board
b d is
i routed
t d to
t the
th IR board
b d via
i J3 andd output
t t on J1 KKey 1 and
dKKey 2 li
lines,
(Key 1 pin 4 and Key 2 pin 5). Arriving at P2401 pins 4 and 5 on the Main Board.
Then to the Microprocessor Pins A4 and B4.
Key Board
P3000
To Main Board
J1
J2
IR board
IR board
IR Receiver
Diode Check
R indicates Red Lead
B indicates Black Lead IR
Center Leg Ground
Power LEDs
On P3000 (Key 1 is pin 1 and Key 2 is pin 3), Pins 2 and 4 are ground.
Key 1 / 2 Voltage and Resistance Chart with buttons pressed.
Installed
This section shows the 11X17 foldout thats available in the Paper
and Adobe version of the Trainingg Manual.
4
3
J2
9-12 3.5V 3.41V 3.4V Open 21 12V 0V 11.96V Open
Disconnect P402 on Main Board.
12V Pins 2 ~ 5 and
1
T109 Q103 13-16 Gnd Gnd Gnd Gnd 22 (4)
0.3V 4.49V Open
A-DIM
2 2
3 1
3 1 and 30 are Gnd. Jump pin 1 (PWR_ON) to pin 9, 10, 11 or 12 .
LVDS Video Signals
1 17 12V 0V 11.96V Open 23 N/C n/c n/c Open This should force the SMPS to the on state. All
To Back 2 2 Q109
CN1 Jumper
3
24 (5)
P-Dim 0V 2.46V Open Voltages should be produced.
Light Diode (24V and 12V to Main. 24V to Inverter).
1
Q104 Check The Backlights should come on.
4 2 2
3 SMPS Used in the 32LD350:
All pins
T108 EAY60868901 32LD350 AUSWLJR or P402 to SMPS P201
3 1
1
Q108 Open
2 2
3 AUSDLFR or AUSDLUR or AUSDLJR Pin Diode Check
Except Gnd
1
D251 D255
1 2.75V
2 2
3
Q107 EAY60869101 32LD350 CUSWLH or 2-4 Open
To Back CUSDLH or CUSWLHO 5-8 Gnd
Light 2 2
1
Q101 9-12 0.91V
4 3
3 1
1
1) Gnd Q601 (5)
P-DIM Pin 24
2 +3.3V_AVDD_MPLL
Digital IC7702
U201 U2 2 2 2) 9.03V IC601 +1.8V_AMP
3 Video
3) 4.58V (Silk Screened Error_Out) 3.3V_Normal
In
2
D7706 A2
T103
3 Output from the Video Q7701 C Mute B E B E
TUNER TDVJ-H001F Q1103 2
Warning: Over 1.2Kv 1 2 3) 0V
L L600 IC7701 Q1105 A2 A1
SIDE A/V
3
J1 Ft IR L607 2 2
Light 3) 24.07V Hot Gnd (Shock Hazard) P2401 Main to J1 "IR Board" L606
JK1104 IC1201 Audio
10. NC
9. SIF
E B
Q5004
1
2Msec per/div P203 "SMPS" to CN1 "Inverter PWB" 5.27M Menu 0.52V
5 Key 2 3.4V 3.39V 1.52V Open R-R+L-L+
+5V_TU
0.98M Enter 0.10V P2401 From 5V_Normal
44V p/p 120Hz Pin Label STBY Run Diode 6 ST_3.3V 3.41V 3.39V 0.9V 2.97V
50% P-DIM 1,2,3,4,5 24V 0V 24.19V Open Key 2 7 Gnd Gnd Gnd Gnd Gnd Main Boards Used in the 32LD350:
Resistance Function Voltage
8 To all Speakers EBU60850009 32LD350 AUSWLJR and AUSDLFR
Pin 3 of T103 ~ T110 6,7,8,9,10 Gnd Gnd Gnd Gnd 17M CH + 1.70V LED_B 0V 0V 2.3V Open
All pins 12.95V EBR66049702 32LD350 AUSDLJR
11 (3)
Error_Out 0.59V Open
10M CH - 1.09V 9 IR 2V 1.98V Open 2.77V J1
0V 5.27M Power 0.52V EBU60850010 32LD350 AUSDLUR
0.98M Input 0.10V 10 Gnd Gnd Gnd Gnd Gnd
12 INV_ON 0V 3.31V Open EBU60850003 32LD350 CUSDLH
(4) 11 +3.3V 0.2V 3.3V 0.58V Open P3000 EBU61005102 32LD350 CUSWLH and CUSWLHO
13 A-DIM 0V 4.5V Open Voltage and Resistance taken J2
2Msec per/div 14 (5)
P-Dim 0V 2.46V Open
with AC applied to the set. 12 LED_R 2.49V 0V 2.14V Open
Pin 1 Key 1
Front IR
No Button pressed Resistance is
2.6V p/p 120Hz Open and Voltage is 3.4V Pin 3 Key 2 IR Receiver
50% P-DIM Diode Check Open Power Button
Pins 2 and 4 Gnd
IC101 Serial Flash IC403 (+1.26V_VDDC) IC407 (D1.8V) IC5001 (+1.26V) for Tuner Q7702 HDMI 4
Pin Memory Pin Regulator Pin Regulator Pin Regulator Pin Det
[1] 0.05V [1] 0.79V [1] 0.8V [1] 3.3V (In) B 0.63V
[2] 3.28V [2] 0V (Gnd) [2] 0V (Gnd) [2] 1.26V (Out) C 0V
[3] 2.26V [3] 3.37V (In) [3] 3.38V [3] 0V (Gnd) E Gnd
[4] 0V (Gnd) [4] 4.47V [4] 4.79V
[5] 0V [5] 3.34V [5] 3.35V Q100 Write Protect for D1100 5V Routing
[6] 0V [6] 1.3V (Out) [6] 1.76V (Out) Pin IC101 Pin for IC1100
[7] 3.28V (B+) [7] 1.3V (Out) [7] 1.76V (Out) B 0V [A1] 0.07V
[8] 3.28V (B+) [8] 2.96V (PWR On/Off2_1) [8] 2.36V (PWR On/Off1) C 3.3V [A2] 4.98V
E Gnd [C] 4.37V
IC105 HDCP IC405 (+3.3V_NORMAL) IC1000 (+1.2V_PVSB)
Pin EEPROM Pin Regulator Pin Regulator Q1100 Earphone Mute D7705 5V Routing
[1] 0V (Gnd) [1] 0V (Gnd) [1] n/c Pin 1st Driver Pin for IC7701
[2] 0V (Gnd) [2] 11.92V (In) [2] 3.26V (Enable) B 0V [A1] 0V
[3] 3.3V (B+) [3] 0V (Gnd) [3] 3.26V (In) C 2.26V [A2] 4.98V
[4] 0V (Gnd) [4] 0.8V [4] n/c E Gnd [C] 4.71V
[5] 0V [5] 0.84V [5] n/c
[6] 3.3V [6] 2.39V (PWR On/Off1) [6] 1.81V (Out) Q1103-4 EARPHONE
[7] 0V (Gnd) [7] 3.35V (Out) [7] 1.21V Pin MUTE
[8] 3.28V (B+) [8] 3.35V (Out) [8] n/c B 0V
C 0V
IC401 5V Regulator IC406 (+5V_NORMAL) IC1450 5V Shot Protection E Gnd
Pin for USB Pin Regulator Pin for USB
[1] 11.9V (In) [1] 0V (Gnd) [1] 0V (Gnd) Q1105 Earphone Mute
[2] 5.09V (Out) [2] 11.92V (In) [2] 5V (In) Pin 2nd Driver
[3] 5.09V (Out) [3] 0V (Gnd) [3] 5V (In) B 0.63V
[4] 0V (Gnd) [4] 0.8V [4] 0V (USB-Ctl) C 0V
[5] 3.25V (PWR On/Off1) [5] 0.84V [5] E Gnd
[6] 0.8V [6] 2.39V (PWR On/Off1) [6] 5V (Out)
[7] 5.05V [7] 4.98V (Out) [7] 5V (Out)
[8] 0V (Gnd) [8] 4.98V (Out) [8] n/c
IC103 Reset IC1100 Earphone IC1201 RS232 IC7702 EDID Data Q407 PANEL_VCC Q5004 Tuner SIF
Pin Generator Pin Amp Pin Data Buffer Pin HDMI4 Pin Control 2nd Driver Pin (Sound) Buffer
[1] Gnd [1] 2.14V [1] 3.34V [1] 0V (Gnd) B 0.679V B 0.163
[2] 0V [2] 0V (Gnd) [2] 3.48V [2] 0V (Gnd) C 0V C Gnd
[3] 3.39V [3] 0.02V [3] 0V [3] 0V (Gnd) E Gnd E 0.85V
[4] 2.19V [4] 0V [4] 0V (Gnd)
IC104 EEPROM [5] 2.19V [5] (-5.37V) [5] 4.69V Q409 PANEL_VCC Q7701 HDMI 2
Pin Mstar [6] 4.37V [6] 5.39V [6] 4.69V Pin Switch Pin Det
[1] 0V (Gnd) [7] 2.19V [7] (-5.37V) [7] 4.69V S 11.97V (In) B 0.63V
[2] 0V (Gnd) [8] 2.18V [8] n/c (0V) [8] 4.69V G 1.84V (Enable) C 0V
[3] 0V (Gnd) [9] n/c (3.39V) D 11.97V (Out) E Gnd
[4] 0V (Gnd) IC1104 Optical Audio [10] n/c (3.35V) Q401 Power On/Off
[5] 3.31V Pin Amp [11] n/c (0V) Pin Driver for Q402 Q600 AMP_MUTE Q7703 CEC Remote
[6] 3.31V [1] 1.64V [12] 3.35V B 0.64V Pin Pin 25 IC600 Pin HDMI CEC
[7] 0V (Gnd) [2] 3.29V [13] 0V C 0V B 0.08V [B] 3.39V
[8] 3.31V [3] 0V (Gnd) [14] 5.47V E Gnd C 3.35V [G] 3.32V
[4] 0V (Gnd) [15] 0V (Gnd) E Gnd [S] 0V
IC400 (+3.3V_AVDD_MPLL) [5] 3.29V [16] 3.37V Q402 Power On/Off [D] 3.26V
Pin Regulator Pin Switch Q1101-2 EARPHONE
[In] 3.35V IC1105 EDID Data IC7701 EDID Data 1 3.39V (In) Pin MUTE D102 Mute
[Gnd] Gnd Pin PC Pin HDMI2 2 0.89V (Ctl) B 0V Pin Routing
[Out] 3.34V [1] 0V (Gnd) [1] 0V (Gnd) 3 3.28V (Out) C 0V [A1] 0V
[2] 0V (Gnd) [2] 0V (Gnd) E Gnd [A2] 0V
IC601 (+1.8V_Amp) [3] 0V (Gnd) [3] 0V (Gnd) Q405 Inverter On/Off [C] 0V
Pin Regulator [4] 0V (Gnd) [4] 0V (Gnd) Pin Switch Q2405 IR Buffer
[1] Gnd [5] 4.7V [5] 4.7V B 0.06V Pin 1st Driver D1115 5V Routing
[2] 1.81V [6] 4.7V [6] 4.7V C 3.32V B 0.6V Pin for IC7705
[3] 3.31V [7] 4.7V [7] 4.7V E Gnd C 0V [A1] 0.03V
[8] 4.7V [8] 4.7V E Gnd [A2] 0V
IC408 Power_Det Q406 PANEL_VCC [C] 4.69V
Pin 24V, 12V, 3.5V D7703 3.5V Blocking D7706 5V Routing Pin Control 1st Driver Q2406 IR Buffer
[1] 3.52V Pin for Q7703 Pin for IC7702 B 0.03V Pin 2nd Driver
[2] 3.35V [A1] 0V [A1] 4.98V C 0.69V B 0V
[3] Gnd [A2] 3.37V [A2] 0V E Gnd C 3.3V
[C] 3.3V [C] 4.69V E Gnd
5uSec per/div 625mV p/p 5uSec per/div 561mV p/p 5uSec per/div 548.5mV p/p 5uSec per/div 565.1mV p/p 5uSec per/div 349.9mV p/p
5uSec per/div 535.6mV p/p 5uSec per/div 540.7mV p/p 5uSec per/div 534.1mV p/p 5uSec per/div 583.9mV p/p 5uSec per/div 395mV p/p