Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
MODULE-25C
__________________________________________________________________________________________
(a) (b)
(c) (d)
Ans:
*L* L
Ans:
at free end = * =
JH ACADEMY Page 1
SUB: STRUCTURAL ANALYSIS
MODULE-25B
3. A rigid beam is hinged at one end and supported on linear elastic
springs (both having a stiffness of 'k') at points' l' and '2', and an
inclined load acts at '2'. Which of the following options represents
the deflections and at points' l' and '2'?
(A) ( ) ( )
(B) ( ) ( )
(C) ( ) ( )
(D) ( ) ( )
Ans:
= = =
= = = =
P*2 = * + *2
P*2 = * + *2
P *2 = 2.5 .
= =
= =
JH ACADEMY Page 2
SUB: STRUCTURAL ANALYSIS
MODULE-25B
4. A simply supported beam is subjected to a uniformly distributed
load of intensity w per unit length, on half of the span from one
end. The length of the span and the flexural stiffness are denoted as
land EI, respectively. The deflection at mid-span of the beam is
(A) (B)
(C) (D)
Ans:
( )
*( ) +
( ) ( )
* + [ ]
* +
a) b)
d)
Ans:
JH ACADEMY Page 3
SUB: STRUCTURAL ANALYSIS
MODULE-25B
6. Consider the following statements:
In the beam shown in the given figure, for all positions of load W
(except x = 0)
1. Bending moment is maximum at B
2. Bending moment is maximum under load
3. Deflection is zero at A
4. Deflection is zero at B
a) 1 and 3 b) 2 and 4
Ans: (d)
( ) (
7. In the figures shown below x,y and z are the deflections under A,B
and C due to loads P and Q. and are the deflection under
deflection z would equal to
a) Px + Qy
b) P +Q
c) Py + Qx
d) P +Q
Ans:
JH ACADEMY Page 4
SUB: STRUCTURAL ANALYSIS
MODULE-25B
8. Assertion (A): in a built-in beam the area of fixed moment
diagram equals the area of free moment diagram.
Reason (R): the first theorem of area moment states that if the
difference of slope between two points is zero, then the area of
bending moment diagram enclosed between these points is also
zero.
Codes:
a) Both A and R is true and R is the correct explanation of A.
b) Both A and R is true but R is not correct explanation of A.
c) A is true but R is false.
d) A is false but R is true
Ans: (a)
a) 20kN b) 40kN
c) 60kN d) 80kN
Ans:
a) Zero b) One
c) Two d) Three
Ans: (b)
a) M b) M c) M/2d) M/2
Ans:
JH ACADEMY Page 5
SUB: STRUCTURAL ANALYSIS
MODULE-25B
12. Which one of the following is true example of a statically
determinate beam?
a) One end is fixed and the other end is simply supported
b) Both the ends are fixed
c) The beam overhangs over two supports
d) The beam is supported on three supports
Ans: (c)
Ans: (b)
a) 6 mm b) 8 mm
c) 11 mm d) 12.5 mm
Ans:
JH ACADEMY Page 6
SUB: STRUCTURAL ANALYSIS
MODULE-25B
15. Which one of the following is the correct BMD for the loaded
uniform sized beam as shown in the figure given below?
Ans: (a)
Ans: (c)
a) 1 b) 2 c) 3 d) 4
Ans: (b)
a) 1 b) 2 c) 3 d) 4
Ans: (b)
JH ACADEMY Page 7
SUB: STRUCTURAL ANALYSIS
MODULE-25B
19. The moment required to rotate the near end of a prismatic beam
through unit angle without translation, when the far end is fixed, is
a) b) c) d)
Ans: (d)
a) 5 b) 9 c) 14 d) 15
Ans: (a)
JH ACADEMY Page 8