Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
2
The key parameters for design of an adsorption system are the process parameters that are
used for modeling the system for predicting the quality of effluent under a wide range of
operating conditions [5]. In most of the large-scale processes, relatively large porous
particles (50-1,000 m in diameter) are used to reduce pressure drop and sorbent cost.
Intraparticle diffusion is usually the rate-limiting step in these systems and it controls the
sharpness of breakthrough curves [6]. One of these models describes diffusion as the
mechanism occurring in the fluid phase with a distributed adsorption along the pore
walls, i.e., the pore diffusion model [7]. For low-affinity solutes in macroporous sorbents,
pore diffusion is usually the dominant intraparticle diffusion mechanism [8].
Pore diffusion model has been used for predicting the kinetics of fixed bed adsorption
process [6,9,10,11]. These models take account of both external and internal mass-
transfer resistances as well as of nonideal plug flow along the column. The above models
have not incorporated the fluid velocity variation along the bed, which makes a
significant effect on breakthrough curve. In the present work, the effect of operating
variables on the process of fixed-bed adsorption is studied. Furthermore, the kinetics is
studied using a mathematical model that takes account of both external and internal mass-
transfer resistances, nonideal plug flow along the column and the variation of fluid
velocity along the column.
2. Mathematical Modeling
Before discussing the assumptions needed for model formulation, we first introduce the
physical process considered in this model. Convection along the column axial direction
and axial dispersion are the mass transport mechanisms in the bulk phase. Molecules
from the bulk interstitial phase are transported via axial convection and Fickian diffusion
(film diffusion) onto the particle surface. Inside the particle, molecules can diffuse into
the inner portion of particle via surface diffusion, pore diffusion, or both. This study
focuses on understanding the mechanism in pore diffusion.
Bautista et al. [9] proposed the kinetic mechanism for the adsorption of -amylase from
Aspergillus oryzane in a fixed bed. The model takes account of both external and internal
3
mass-transfer resistances as well as of nonideal plug flow along the column. They did not
consider the fluid velocity variation along the bed to predict the behavior of breakthrough
curve. In the present study this model is modified by considering the variation of velocity
along the column.
2C C C q
DL b +V b + C V + b + 1 p
=0
z 2 z b z t p t
(1)
V
C b
C b ( z , t ),
z
dz
(C bV ) C b 2C b
Cb + dz , + dz
z z z 2
4
The following initial condition is considered
C b = C bo z = 0, t = 0 (2)
Cb = 0 0 < z L, t = 0 (3)
The contour conditions at both ends of the column are given by the following equations
C b
DL = V0 (C bo C b ), z = 0, t > 0 (4)
z
C b
= 0, z = L, t 0 (5)
z
The superficial velocity, V in fixed-bed adsorption is not constant because of adsorption.
The following equation was used to estimate (dV/dz), the variation of velocity of bulk
fluid along the axial direction of the bed. For liquid adsorption, assuming the liquid
density to be constant, then the total mass balance gives
V q p
l = (1 ) s (6)
z t
Velocity boundary conditions
V = V0 , z = 0, t > 0 (7)
V
= 0, z = L, t > 0 (8)
t
The inter-phase mass transfer rate may be expressed as
q p 3k f
s = (C b C s ) (9)
t ap
The intra-pellet mass transfer is due to the diffusion of adsorbate molecules through the
pore. The macroscopic conservation equation is given as
c q 2 c 2 c
p + (1 p ) p = Dp + (10)
t t r 2 r r
5
c 1 2 c 2 c
= DP + (12)
t 1 P q r 2 r r
1 + p
P c
The following initial condition is considered
c = 0, q = 0, 0 < r < ap , t = 0 (13)
The symmetry condition at the center of the particles and continuity condition on the
external surface of the adsorbent bed are expressed as
c
= 0, r = 0, t > 0 (14)
r
c
k f (C b C s ) = Dp , r = ap , t > 0 (15)
r
The adsorption isotherm was favorable and nonlinear, and it described by Langmuir
isotherm
q m bc
q= (16)
1 + bc
6
Table 1: Model parameters value for simulation [9]
Parameter Value
,Bed porosity, (-) 0.58
p, Particle porosity, (-) 0.53
[9] are used and some parameters (see Table 1) are assumed which are not given in
literature. The present model results show an improvement over the previous model given
by Bautista et al. [9] with respect to better steepness of the breakthrough curve which is
being validated by earlier study [6,18]. The results show that the breakpoint is obtained
earlier (Figure 2). Initially the sharp front of the breakthrough curve is seen followed by
broadening of tail of the breakthrough curve as shown in Figure 2 [18]. These obtained
results are more justifiable with theoretical phenomena occurring in the adsorption
system. The fluid velocity along the bed is a decreasing function of bed length [18]. The
velocity continuously decreases inside the bed with respect to bed length. This
phenomenon is validated by the mass balance (Eq. 6) for velocity variation. This
establishes the fact that the effect of velocity variation on breakthrough curve is
significant. This fact is also in agreement with the results reported in the literature [18].
Based on the successful implementation of velocity variation in the model, and
supporting evidence in the literature, the simulations are carried out using the present
model to carryout a systematic parametric study. The present model is studied by varying