Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Alumalite Table Form is the result of Aluma Systems unequaled experience
of truss system development and use. With a patented leg design that allows
extension staffs and jacks to be used at the top and bottom of the table, this
system can adapt to most slab and beam configurations, while meeting the
demands of todays high speed construction methods.
Product Description
Aluma Systems introduced 4'0" (1.22m). The latter Screwjacks can also be easily to each side of the
the lightweight aluminum allows conventional 4' wide used on the top chord leg. Underslung beams
flying table form to the shoring frames to be mated without an extension staff. can be bolted via the bolt
world over 30 years ago. to the truss either on the The Alumalite leg incorpo- slot to the table as well as
Today, the Alumalite table top or bottom to achieve rates bolt slots on each special bracing for hinge
form is being used in the greater shoring heights. side, for connecting cross- panels.
housing industry and the brace brackets. If using The Alumalite Table
slab and beam shoring Alumalite Table Form three to four trusses per Form conforms to all forming
market as a highly versatile With its revolutionary flying table, the crossbrace regulations, including CSA,
mechanized shoring system. patented double hollow connectors can be attached CAL-OSHA AND ANSI.
The Alumalite System is extruded legs the Alumalite
30% lighter than its prede- table form makes beam and Features
cessor and can be flown in slab construction much Allows the use of extension staffs at the top and
one piece with ease by a easier and faster to handle bottom of the table forms
traditional capacity crane. than previous table forms or Compatible with the full range of Aluma Beams
The depth of the truss is traditional methods. Adjust- and Stringers
exactly 3'11" (1.2m) while ments in height can be Modular design simplifies assembly
the centre to centre dis- done quickly to pick up The most versatile truss system available
tance of the legs is exactly internal beams or spandrels. Reduces construction cycle times
This bulletin is intended only for general information on the Alumalite Table Form. This product is only to be used for
the purpose for which it is intended and only per the load capacities as established by Aluma Systems. This product
must not be used when damaged and must be in fully functional condition. This product must be inspected by the user
before use and properly stored, maintained and repaired. This product must not be misused nor overloaded.
Alumalite Table Form Industrial Services and
Concrete Construction Specialists
Basic Components
41/2"
(144mm)
4" on centre
(102 mm)
38"
(965 mm)
51/2"
(140mm)
12"
191/2"
(350mm)
(495mm)
191/2"
(495mm)
231/2" (597mm)
Specifications
HEIGHT OVERALL WIDTH MIN. CLEARANCE WEIGHT LB. (KG)
38" 231/2" 3" (76 mm) 180 (81.65 )
(965mm) (597mm)
MAXIMUM REACH
Lifting plate in lower position 24" (610mm)
Lifting plate in high position 48" (1.22mm)
Load Charts
Safe Working Load kN (Kips)
4" (1200mm)
Truss
18" B
(450mm)
max.
4'0" (1.2m) Deep Alumalite Truss with Top & Bottom Extension (with Standard #514 Screwjack & Extension Staff)
Safe Working Load kN (Kips)
A
6" (1800mm)
Truss
12" B
(300mm)
max.
6'0" (1.8m) Deep Alumalite Truss with Top & Bottom Extension (with Standard #514 Screwjack & Extension Staff)
Consult our Engineering Department for assistance in the application of these accessories.
Illustrations are not drawn to scale. All dimensions nominal.
Contact Us:
Visit our website at Aluma Systems Aluma Systems Aluma Systems
20071_1.5_09/02