Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SOIL DATA
Reference - Geotechnical Investigation prepared by Gulf Consult
From the bore hole logs at the two locations and as well as from the report it is very clear that
the piles are founded on cohesionless Very dense silty sand. Hence calculations are performed
based on cohesionless soil. The following calculation represents the pile design at grid B & C.
DIMENSION
Diameter of the pile = 914.4 mm
Thickness of pile = 17.7 mm
Theoretical thickness of pile = 11.7 mm
Seabed level = -3.5 m
Depth of fixity below seabed level = 1.0 m
Assumed depth of pile below fixity point = 6.5 m (SP-SM)
Assumed depth of pile below fixity point = 3.0 m (SM)
Angle of internal friction below the fixity point = f = 36.0 (Lower value)
Submerged unit weight of soil below the fixity point = g1 = 10.2 kN/m3 (SP-SM)
Submerged unit weight of soil below the fixity point = g2 = 11.2 kN/m 3 (SM)
Youngs modulus of elasticity = E = 2.05 x 10 5
N/mm 2
MEMBER CHECK
Internal diameter of the pile = d2 = 878.96 mm
Pile outer dia. after corrosion = D = 902.44 mm
Moment of Inertia of pile = I = p (D - d )/64
4 4)
= 0.00326 m4
Stress due to axial load = P/a
= 36.5 N/mm2
Stress due to bending = (M*y / I)
= 54.1 N/mm2
(Referring to BS 6349, all stress is 0.6 Fy) < 240.0 N/mm2 OKAY
Efective overburden pressure(average for 7.5 to 10.5 deep) = pd2 = 110.1 kN/m2 (SM)
Friction angle between pile and soil = d1 = 30 0 (SP-SM)
As the end bearing resistance for the entire base area is much more than the internal
skin friction, the pile behaves unplugged. Hence the internal skin friction is considered
for resistance calculation. For end bearing calculation, only the pile annulus area is
considered.
9.5 m
373.2 kN/m2
SOIL DATA
Reference - Geotechnical Investigation prepared by Gulf Consult
From the bore hole logs at the two locations and as well as from the report it is very clear that
the piles are founded on cohesionless Very dense silty sand. Hence calculations are performed
based on cohesionless soil. The following calculation represents the pile design at grid B & C.
DIMENSION
Diameter of the pile = 914.4 mm
Thickness of pile = 17.7 mm
Theoretical thickness of pile = 11.7 mm
Seabed level = -8.25 m
Depth of fixity below seabed level = 1.0 m
Assumed depth of pile below fixity point = 1.75 m (SP-SM)
Assumed depth of pile below fixity point = 6.00 m (SM)
Assumed depth of pile below fixity point = 2.00 m (SC)
Angle of internal friction below the fixity point = f = 36.0 (Lower value)
Submerged unit weight of soil below the fixity point = g1 = 10.2 kN/m3 (SP-SM)
Submerged unit weight of soil below the fixity point = g2 = 11.2 kN/m 3 (SM)
Submerged unit weight of soil below the fixity point = g3 11.0 kN/m 3 (SC)
Youngs modulus of elasticity = E = 2.05 x 10 5
N/mm 2
MEMBER CHECK
Internal diameter of the pile = d2 = 879.0 mm
Pile outer dia. after corrosion = D = 902.4 mm
Moment of Inertia of pile = I = p (D - d )/64
4 4)
= 0.0033 m4
Stress due to axial load = P/a
= 17.7 N/mm2
Stress due to bending = (M*y / I)
= 50.4 N/mm2
(Referring to BS 6349, all stress is 0.6 Fy) < 240.0 N/mm2 OKAY
Maximum compression = (P/a) + (M y / I)
= 68.1 N/mm2
(Referring to BS 6349, all stress is 0.3 Fy) < 120.0 N/mm2 OKAY
Efective overburden pressure(average for 7.5 to 10.5 deep) = pd2 = 110.1 kN/m 2 (SM)
Efective overburden pressure(average for 7.5 to 10.5 deep) = pd2 = 152.0 kN/m2 (SC)
9.8 m
383.1 kN/m2