Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
The 4th International Conference of Slovenian Society for Nondestructive Testing "Application of Contemporary TABLE OF CONTENTS
Nondestructive Testing in Engineering" 24 - 25 April 1997, Ljubljana, Slovenia. Introduction
Table of Contents Selection Of Testing Method
Types of inhomogeneity
Characteristics of testing methods
Extent Of Testing
1 INTRODUCTION Practice in Slovenia
Influence of quality assurance (QA) and quality control (QC)
Proposal for determination of the extent of testing
Each testing of welded joints should start with the selection of a suitable testing method Conclusion
Literature
and determination of the extent of testing. One should be aware that the selection of a
testing method and determination of the extent of testing are as important as testing itself
when the final result is considered. Owing to the selection of an unsuitable testing method NDT methods often become purposeless.
When planning NDT testing one should take into account a number of factors such as:
In the selection of a suitable NDT method, welding technologists and NDT experts should be involved, and in determining the extent of testing
designers, who know best which are the intended operating conditions of a device to be tested and which locations may be loaded most.
The selection of the NDT method is usually the concern of NDT laboratories, which know the NDT methods and their feasibility in detecting
defects. Regarding properties of materials and characteristics of a welding process it should be first established what types of defects may occur
and where. It should also be established which part of a structure may incur the highest stresses.
An expert may, with a high level of certainty, predict which types of defects may occur and at which locations are they most probable. Attention
should be paid to bonding defects and cracks, which are in no case admissible. A little more toleration may be shown to pores and non-metal
inclusions. But a careful examination of heavily loaded parts of a structure should be carried out.
http://www.ndt.net/article/v04n05/rihar/rihar.htm 1/8
11/1/2017 SELECTION OF AN NDT METHOD AND THE EXTENT OF TESTING
Hot cracks, i.e. crystallization cracks, usually occur in the middle of the weld. Hotcracking sensibility is found in alloys, alloyed steels and
steels containing a higher level of impurities, usually in welds of larger dimensions. Cold cracks occur mostly in the heat affected zone. They
occur in steels susceptible to through-hardening and hydrogen embrittlement.
A special attention should be paid to porosity in gas-shielded welding, submerged arc welding, and welding with basic electrodes.
Typical cracks in the welded joint and location of their appearance is shown in Fig. 1.
In testing of welded joints, it is radiographic methods which are most frequently used and which permit a very reliable detection of three-
dimensional discontinuities such as pores, non-metallic inclusions, incomplete penetration and undercuts at the inaccessible root side. The
method seems to be less reliable in detecting planar, i.e. two-dimensional, defects such as cracks.
The ultrasonic methods seem to be the most universally applicable. They may be applied to all types of defects but they are comparatively
complicated and sensitive to various disturbances. They are less reliable, therefore, they are making themselves valued in welding very slowly.
Simple and reliable methods are available for detection of cracks reaching the surface. Magnetic methods are suitable for ferromagnetic
materials, while penetrant methods are suitable for all metals.
Too little attention is, however, paid to visual inspection which should be performed prior to each NDT examination. The visual inspection
provides basic information on the state of welded joints and the structure concerned. This is a guideline for further examinations. Fig. 2
http://www.ndt.net/article/v04n05/rihar/rihar.htm 2/8
11/1/2017 SELECTION OF AN NDT METHOD AND THE EXTENT OF TESTING
schematically shows the application of various NDT methods in testing butt and fillet welds.
In addition to technical considerations, in the selection of testing methods the cost of testing should be considered as well. The more perfect
weld is to be obtained, the more should be invested into NDT methods (Fig. 3). Fig. 4 shows market rates for NDT methods in Slovenia.
Fig. 3. Ratio between control cost and weld Fig. 4. Standard market rates for NDT methods in
perfection Slovenia
3 EXTENT OF TESTING
The extent of testing is a datum informing us what part of the total length of welded joints and which locations is to be tested. The extent of
testing is sometimes determined by the client in the invitation to project tender, but most frequently by a designer taking into account technical
regulations in force and stresses calculated for individual welded joints.
http://www.ndt.net/article/v04n05/rihar/rihar.htm 3/8
11/1/2017 SELECTION OF AN NDT METHOD AND THE EXTENT OF TESTING
In the techical regulations in force provisions on the minimum extent of NDT testing of welded joints may be found. Although some are rather
old they are still in force (5, 6). They are not consistent with each other and they may be applied only to certain fields. An exception is the
standard on quality levels with a general applicability (7).
For steam boilers and steam superheaters a 30 % radiographic examination of butt welds is specified (5).
With welded structures the extent of testing depends on the welding location and the joint quality class selected (6). Welds made in a workshop
require less testing than out-of-position field welds. Regarding the load and the level of requirements, three classes are distinguished: special,
first and second.
The regulations on pressure vessels are the most elaborate ones. The extent of testing depends on operating conditions of the vessel (vessel
class), the type of joint and strength calculation (8, 9, 10). There are four classes of welded joints. A selection may be made among various
levels of perfection of welded joints.
A similar division into four quality classes may be found in the general quality standard (7) which is applied to pipelines, with the exception of
main pipelines for liquid and gas hydrocarbons where the extent of testing is regulated in a different way (11). The latter depends on the
distance from settlements, energy facilities and traffic routes.
Among the methods for testing welds, the radiographic method is preferred. In older regulations other methods are not mentioned. More recent
regulations permit application of ultrasonic methods instead of radiography. Other methods are applied only as a complement.
When selecting the extent of testing, the level of quality assurance achieved should be taken into account. This has not been taken into account
in Slovenia till now. Also some foreign regulations known in Slovenia do not take quality assurance into account.
More recent standards specify three levels of quality assurance, which permits, when selecting
the extent of testing, to give consideration also to the level of quality assurance achieved by the
performer of welding work. The welded-joint quality (Q) may be defined as a sum of quality
assurance (QA) and quality control (QC).
The maximum quality in the instance selected may be achieved if all means of quality
assurance available are taken into account and all NDT methods available are applied. The
relation between quality assurance (QA) and the extent of quality control (QC) is graphically
shown in Fig. 5.
Table I: Survey of testing methods specified Fig. 5. Ratio between quality assurance (QA) and
http://www.ndt.net/article/v04n05/rihar/rihar.htm 4/8
11/1/2017 SELECTION OF AN NDT METHOD AND THE EXTENT OF TESTING
Field of application Level of Extent and method of testing quality control (QC)
requirements
Steam boilers and
- 30 % RT
steam superheaters
Steel structures S 100 % RT, MT and PT if required
I 10-50 % RT, MT and PT if required
II RT of out-of-position welds
Pipelines I 100% RT or VT, 100 % MT or PT
JUS C.T3.010 II 50 % RT or VT, 100 % MT or PT
III 10 % RT or VT, 30 % MT or PT
IV -
Pressure vessels
100 % RT or VT, 100 % MT or PT
I
70 % RT or VT, 100 % MT or PT
II A
50 % RT or VT, 100 % MT or PT
II B
30 % RT or VT, 30 % MT or PT
III A
10 % RT or VT, 30 % MT or PT
III B
no requirements
IV A
30 % MT or PT
IV B
100 % UT, 100 % MT or PT
Ic
50 % UT, 50 % MT or PT
II c
100 % UT, 100 % MT or PT
ID
70 % UT, 100 % MT or PT
II D
310%UT, 30%MT or PT
III D
Main pipelines Zone I 10 % RT, MT or PT if required
Zone II 50 % RT, MT or PT if required
Zone III 100 % RT, MT or PT if required
- For all quality levels a 100 % visual inspection is required.
- MT and PT are performed only if there is a risk of cracks.
Quality assurance requires a number of operations usually expressed by levels. The new European standard specifies elementary (1), standard
(11) and comprehensive (Ill) levels (12).
The level selected may be achieved by a higher level of quality assurance and less control (instance a) and vice versa (instance b). Both
instances are shown in Fig. 6.
Similar conclusions may be drawn if quality assurance and quality control are considered production costs and both together quality cost. In this
case the following holds true:
Q = QA + QC (monetary unit)
Fig. 6. Quality selection between QA and QC Fig. 7. Cost model for quality
It may be concluded that quality assurance and control complement each other and jointly produce quality. In practice both means, however, are
not balanced, which is shown by the model (Fig. 7). In certain cases quality assurance is a more efficient means than quality control and vice
versa; therefore, each is used as appropriate.
In practical applications a certain lower threshold is more and more being taken into account; these are a welder's approval test certificate in
quality assurance and the visual examination in quality control. For pressure vessels and load-bearing welded structures the lower threshold is
determined by the requirements related to the issue of a certificate of qualification to the workshop concerned.
When determining the extent of testing, beside requirements for reliable and safe operation of the structure, also the level of quality assurance
already achieved by the performer of welding work should be considered. Structures may be divided into three classes, i.e. very exacting,
http://www.ndt.net/article/v04n05/rihar/rihar.htm 6/8
11/1/2017 SELECTION OF AN NDT METHOD AND THE EXTENT OF TESTING
The ratio between the level of quality assurance achieved, the requirements, and the extent of testing may be graphically presented (Fig. 8).
Table 11 shows how the extent of testing may be determined as a function of the level of quality assurance achieved.
We have been used to standards determining quality classes as well as the minimum extent of testing. Recent standards have no such provisions
because the level of acceptance of defects, which is determined by their size and number, has nothing to do with the extent of testing. But in any
case a higher level indicates a higher quality of the welded joint (Fig. 9). Quality levels B, C, and D were taken from the new European
standard (13).
4 CONCLUSIONS
Quality assurance and quality control complement each other. With a higher level of quality assurance the extent of testing may be reduced. The
above-mentioned principle would certainly stimulate performers of welding work to invest more into quality assurance.
It is suggested that the above-mentioned principle of determining the extent of testing be implemented in the elaboration of new Slovenian
technical regulations.
5 REFERENCES
1. IlW Guidance on Assessment of the Fitness for Purpose of Welded Structures. Doc. IIS/IlW-SST-1 157-90 (pp. 67-74, 229-296).
http://www.ndt.net/article/v04n05/rihar/rihar.htm 7/8
11/1/2017 SELECTION OF AN NDT METHOD AND THE EXTENT OF TESTING
NDT.net
NDT.net, info@ndt.net
/DB:Article /DT:tutor /AU:Rihar_G /CN:LT /CT:NDT /CT:reliability /ED:1999-05
http://www.ndt.net/article/v04n05/rihar/rihar.htm 8/8