Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
The B600 Retrofit (ZONEX) module enables the use of ZONEX Install the module in the enclosure, and then connect it to Using your existing terminal wiring strip, retrofitting your
devices on the B9512G/B8512G control panel. The B600 the control panel. current ZONEX devices to your new control panel is easy.
module connects to the control panel through a proprietary
PWR+/R 29
A/Y 28
connection (cable provided with module) and establishes Remove the terminal strip which contains the legacy ZONEX
SDI2
B/G 27
ire
2 devices from the legacy control panel by tilting the strip up
ZONEX terminals. Remove all power (AC and battery) before making any and outward. Do not remove the wiring from the terminal strip.
SDI2
Y
2
A/Y 25
SDIx
G
injury and/or equipment damage.
B/G 24
COM/B 23
B
OUT
ZX1
1
ZX1
IN
R
OUT
ZX2
3.1 | Mount the module in the enclosure
ZONEX TAMPER RESET
ZX2
IN
COM PWR
1
ZONEX
G
Mount the module into the lower right area of the control
panel enclosures 3-hole mounting pattern using the supplied
B
screws and mounting bracket. Refer to Figure 3.1. Figure 4.1: Wiring the module to the control panel (B9512G
OUT
ZX1
2
ZX1
IN 3 shown)
Callout Description
OUT
ZX2
1
ZX2
1
COM PWR
ZONEX
Y
2 | Pre-installation 1 Module and three hole mounting bracket (-) 3
G
2 Control panel enclosure (+)
1
B
Remove the terminal strip (provided) from the B600 prior 2 (+)
OUT
ZX1
to retrofit applications. Do this by tilting the strip up and 3 Mounting screws (3)
ZX1
IN
outward. Refer to Figure 2.1. GND
OUT
ZX2
OUT
4 | Wiring IN
ZX2
IN
Refer to Section 4.4. for new installations which require AUX
COM PWR
wiring into the B600 terminal strip.
ZONEX
Perform the following steps to wire the B600 module.
2
1
4.1 | Wiring to the control panel
Use the modules cables provided when you wire the module Figure 4.2: Wiring a B600 module to a legacy module (D8125
to a control panel. Program the SDIx bus to operate as the SDI shown)
bus. Make cable connections to the control panel as shown in Callout Description Figure 5.2: Inserting the terminal strip into the B600
2 Figure 4.1.
1 B600 Callout Description
2 ZONEX module (D8125 shown) 1 Terminal strip (from legacy control panel)
2 B600
1
The B600 ZONEX module includes two ZONEX busses (ZONEX1, UL 636 - Holdup Alarm Units and Systems
ZONEX2). Each ZONEX bus supports up to 15 D8128D modules, UL 864 - Control Units and Accessories for Fire Alarm Systems
and/or up to D8129 Octo-relay modules. D8128D and D8129
UL 985 - Household Fire Warning System Units
modules can be combined on a single ZONEX bus. Total number
of modules cannot exceed 15 modules. Refer to the following UL 1023 - Household Burglar-Alarm System Units
table for supported compatibilities. UL 1076 - Proprietary Burglar Alarm Units and Systems
UL 1610 - Central Station Burglar Alarm Units
ZONEX wiring Use the supplied ZONEX connection cable (P/N: F01U295103)
Compatible control B9512G/B9512G-E/B8512G/B8512G-E (Refer to the control panel installation document for the
panels number of supported devices.)
Compatible accessories D8125 Zone Expansion Module
D8128D OctoPOPIT Module
D8129 Octo-relay Module