Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
PERANCANGAN KULIAH
LECTURE PLAN
The aim of this course is to prepare the basic knowledge for students to use fluid mechanics in engineering,
especially in solving the problem of static and fluid dynamic.
1. Applying the concept.
2. Understanding the dimensional analysis method, such as Buckingham and Rayleigh.
Matlamat kursus ini adalah untuk menyediakan pengetahuan asas kepada pelajar pengunaan mekanik
bendalir dalam bidang kejuruteraan terutama dalam menyelesaikan masalah bendalir statik dan dinamik.
1. Mengaplikasi konsep.
2. Memahami kaedah analisis matra seperti Buckingham dan Rayleigh.
SINOPSIS (SYNOPSIS):
Physics Fluids, Static Fluids, Fluids kinematics, Energy and Momentum, and Matra Analysis.
TEST 2 ( 1 HOURS)
4.0 ENERGY AND MOMENTUM (1 HOURS)
Students are required to design and fabricate a simple experimental apparatus describing or showing the
principle of Fluid Mechanics. It can be made from low cost or recycled or used item/material. This apparatus
then must be tested at various design or test parameters. The experimental result then needs to be discussed
and compared with theoretical data.
PENTAKSIRAN (ASSESSMENT):
1. Kuiz (Quiz) : 5%
2. Tugasan (Assignment) : 5%
3. Ujian (Test) :
- Ujian 1 : 10 %
- Ujian 2 : 10 %
4. Project (Project)
- Pembentangan (Presentation) PLO3 : 5%
- Hasil projek dan laporan (Project and Report) : 15%
PLO2
1. Pelajar mesti hadir tidak kurang dari 80% masa pertemuan yang ditentukan bagi sesuatu kursus termasuk
kursus Hadir Wajib (HW) dan kursus Hadir Sahaja (HS).
Students must attend not less than 80% of the contact hours specified for a course including Compulsory
Attendance (HW) course and Attendance Only (HS) course.
2. Pelajar yang tidak memenuhi perkara 1 di atas tidak dibenarkan menghadiri kuliah dan menduduki
sebarang bentuk pentaksiran selanjutnya. Markah sifar 0 akan diberikan kepada pelajar yang gagal
memenuhi perkara 1. Manakala untuk kursus HW, pelajar yang gagal memenuhi perkara 1 akan diberi
gred Hadir Gagal (HG).
Students who do not fulfill item 1 of the above are not allowed to attend further lecture and sit for any
form of assessment. Zero 0 mark will be given to students who fail to comply with item 1. As for HW
course, students who fail to comply with item 1 will be given Failure Attendance (HG) grade.
3. Pelajar perlu patuh kepada peraturan berpakaian yang berkuatkuasa dan menjaga disiplin diri masing-
masing untuk mengelakkan dari tindakan tatatertib diambil terhadap pelajar.
Students should adhere to the dress regulations in effect and must discipline themselves to avoid from
any disciplinary actions.
4. Pelajar perlu mematuhi peraturan keselamatan sepanjang aktiviti pembelajaran dan pengajaran.
Students should adhere to the safety regulations throughout the learning and teaching activities.
Fakulti (Faculty) : CENTRE FOR DIPLOMA STUDIES Matrik ini perlu digunakan bersama:
Program (Programme) : DIPLOMA OF MECHANICAL ENGINEERING (This matrix is to be used with)
1. Objektif Pendidikan Program (PEO)
Kod Kursus (Course Code) : DAM 31503 (Programme Educational Objectives
(PEO))
Nama Kursus (Course Title) : FLUID MECHANICS 2. Hasil Pembelajaran Program (PLO)
(Programme Learning Outcomes
(PLO))
Pematuhan kepada PLO (Compliance to PLO)
Kaedah Kaedah
PLO10
PLO11
PLO12
PLO13
PLO1
PLO2
PLO3
PLO4
PLO5
PLO6
PLO7
PLO8
PLO9
Hasil Pembelajaran Kursus Penyampaian Pentaksiran
No. KPI
(Course Learning Outcomes) (Method of (Method of
Delivery) Assessment)
Describe briefly the fluid properties. (PLO1- Quiz, Test,
Answer
CLO1 C3) C3 Assignment and Final
Schemes
Examination
50% of
Practice pressure and force solution exerted the
by the fluid on a body in a static condition. students
CLO2 Project /Report Rubric
(PLO2-P3) P3 achieved
C+ and
above
Presenting projects result using the
CLO3 concepts of fluid mechanics.(PLO3-A2) A2 Presentation Rubric