Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
FX-301(P)-F
z SPECIFICATIONS c MOUNTING
Type NPN output type PNP output type How to mount the amplifier
Item Model No. FX-301-F FX-301P-F w
q Fit the rear part of the mounting section of the
Applicable fiber FD-F7 series, FT-F9 series
amplifier on a 35mm width DIN rail.
Supply voltage 12 to 24V DC ± 10% Ripple P-P 10% or less q
w Press down the front part of the mounting section
Normal operation: 960mW or less (Current consumption 40mA or less
of the amplifier on the 35mm width DIN rail. 35mm width DIN rail
at 24V supply voltage)
Power consumption
Eco-operation: 600mW or less (Current consumption 25mA or less at
24V supply voltage) How to remove the amplifier q
NPN open-collector transistor PNP open-collector transistor w
• Maximum sink current: 100mA (Note 1) • Maximum source current: 100mA (Note 1) q Push the amplifier forward.
• Applied voltage: 30V DC or less • Applied voltage: 30V DC or less w Lift up the front part of the amplifier to remove it.
Output Note: Take care that if the front part is lifted up without pushing
(between output and 0V) (between output and +V)
the amplifier forward, the hook on the rear portion of the
• Residual voltage: 1.5V or less • Residual voltage: 1.5V or less
mounting section is likely to break.
[at 100mA (Note 1) sink current] [at 100mA (Note 1) source current]
When Leak is set (F7 mode): OFF when leak is detected.
When Liquid is set (F9 mode): Selectable, either OFF when no liquid is How to connect the fiber cables
Output operation
detected (NC) or ON when liquid is
detected (NO), with jog switch. Make sure to fit the fiber attachment (FX-AT4), enclosed with the fiber, to the
Short-circuit protection Incorporated fibers.
Response time 250µ s or less (Note 2) Please refer to the instruction manual of the fiber attachment for the fitting
Display 4 digit red LED display method.
Sensitivity setting method Individual teaching / Collective teaching
Fine sensitivity q Snap the fiber lock lever down.
Incorporated w Insert the fiber cables slowly into the inlets until
adjustment function e
Timer function Incorporated with delay timer [Effective only when Liquid is set (F9 mode)] they stop. (Note 1) q
0 to +50°C (If 8 to 16 units are connected together: 0 to +45°C) e Return the fiber lock lever to the original posi- Fiber
Ambient temperature tion, till it stops. lock lever
(No dew condensation or icing allowed), Storage: –20 to +70°C
Ambient humidity 35 to 85% RH, Storage: 35 to 85% RH Note: In case the fiber cables are not inserted to a position
where they stop, the sensing becomes unstable. w
Emitting element Red LED (modulated)
Material Enclosure: Heat-resistant ABS, Transparent cover: Polycarbonate Fiber attachment
Weight 20 g approx.
Fiber
Notes: 1) 50mA if five, or more, amplifiers are con- 1 sec.
250μs
v CONNECTION
nected together. approx.
2) If a leak is detected (Output: OFF) in
ON
Leak (F7 mode), since the emission is
put in blinking operation, only the re- Make sure to connect or disconnect the quick-connection cable in the power
sponse to return to ON gets delayed.
(1 sec.)
OFF supply off condition.
Note 2: When z MODE key is pressed for 1 sec., or more, the sensor returns to the RUN mode. (in
Dismantling method
MAIN mode only)
q Loosen the screws of the end plates
(MS-DIN-E).
w Remove the end plates (MS-DIN-E).
End plates
(MS-DIN-E) . RUN MODE
(optional)
e Slide the amplifiers and remove them one 䢇 When MODE indicator / RUN (green) lights up, the display setting or the sensitiv-
by one. ity select setting can be checked. Refer to ⁄5 SENSITIVITY SELECTION FUNC-
(For details, refer to c MOUNTING.) TION for further details of sensitivity select setting.
How to change to ‘percent display’
Slide
䢇 When c Jog switch is pressed for 2 sec., or more, the display changes as per the
diagram below.
n I/O CIRCUIT DIAGRAMS <Digit display> Press c Jog switch <Percent display>
䢇 FX-301-F / NPN output type for 2 sec., or more.
Terminal No.
Color code of quick-connection cable
Terminal
arrangement
1234 123P
D (Brown) +V (Note 1) diagram The incident light intensity is dis- The incident light intensity is displayed in
1 played within the range 0 to 4,000. percentage (within 0 to 999) based on the
Sensor circuit
Tr ZD
100mA max. (Note 2) – 䢇 If x Jog switch is turned to ‘ + ’ or ‘– ’ side, the present sensitivity state can be
(Blue) 0V (Note 1) 2 0V confirmed. After 2 sec., the display returns to ‘digit display’ or ‘percent display’.
2
<LO mode> <HI mode>
Lo HI
Internal circuit Users’ circuit
Or
Notes: 1) The quick-connection sub cable does not have +V (brown) and 0V (blue). The power is
supplied from the connector of the main cable.
2) 50mA max. if five, or more, amplifiers are connected together. Operating in the low sensitivity mode. Operating in the high sensitivity mode.
3) Do not use the amplifiers in a series (AND) connection.
Symbols... D : Reverse supply polarity protection diode
ZD : Surge absorption zener diode
⁄0 INDIVIDUAL TEACHING MODE
Tr : NPN output transistor The sensitivity selection function is set to the automatic sensitivity setting (Auto )
䢇 FX-301P-F / PNP output type at the time of factory shipment. In case sensitivity selection setting is done,
Terminal No. Terminal make sure to carry out ‘teaching’ after the sensitivity selection setting.
Color code of quick-connection cable arrangement For the sensitivity selection setting, refer to ⁄5 SENSITIVITY SELECTION FUNCTION.
(Brown) +V (Note 1) diagram 䢇 When MODE indicator / TEACH (yellow) lights up, threshold value can be set on a single unit.
1
Sensor circuit
3) Do not use the amplifiers in a series (AND) connection. • Press c Jog switch in no-leak condition with Leak detection fiber
Symbols... D : Reverse supply polarity protection diode
ZD : Surge absorption zener diode
e
1 (FD-F7M) or no-liquid condition with Liquid detection fiber (FT-F9M).
Then, ‘ 1 ’ on the display moves from left to right.
Tr : PNP output transistor
• When teaching is accepted, the result of threshold value setting is
m PART DESCRIPTION r
9ood displayed.
In case stable sensing is possible: ‘ 9ood ’ on the display blinks
MODE indicator / ADJ (Yellow) three times.
Output operation
indicator (Orange)
Model indicator
(Green) MODE indicator / DISP (Yellow) Er-3 In case stable sensing is not possible: ‘Er-3 ' on the display blinks.
(Note 1)
• If the teaching result is ‘9ood ’, the sensor returns to RUN mode au-
tomatically and the incident light intensity is shown on the display.
MODE indicator / RUN (Green)
MODE indicator /
t
1234 • MODE indicator / RUN (green) lights up.
MODE key • The setting is complete.
MODE indicator / TEACH (Yellow) OUT (Yellow)
Notes: 1) For details, refer to ⁄8 ERROR INDICATION.
MODE indicator / ALL (Yellow) Digital display (Red) Jog switch
2) The initial setting at the time of factory shipment is Liquid (F9) mode (-F9- ).
⁄1 COLLECTIVE TEACHING MODE ⁄3 DIGITAL DISPLAY SETTING MODE
䢇 When MODE indicator / ALL (yellow) lights up, a threshold value can be collec- 䢇 When MODE indicator / DISP (yellow) lights up, the digital display can be switched
tively set to amplifiers mounted in cascade. to the light-up mode, the eco mode or the inverse mode.
Step Display Description Step Display Description
• Inser t Leak detection fiber (FD-F7 M ) or Liquid detection fiber
q
1234 (FT-F9M).
• Press z MODE key to light up MODE indicator / ALL (yellow).
q
EcoF • Press z MODE key to light up MODE indicator / DISP (yellow).
• When x Jog switch is turned to the ‘+’ side or ‘–’ side, the mode in
w
-F7- • Turn x the jog switch to ‘+ ’ or ‘ –’ side to set to either Leak (F7)
mode (-F7- ) or Liquid (F9) mode (-F9- ).
EcoF
the digital display changes.
EcoF : This is the light-up mode in the digital display.
• In case Liquid (F9) mode (-F9- ) is set, the model indicator (Green) The digital display always lights up.
-F9- lights up. Econ : This is the eco mode. After confirmation, if key operation has not
been done for 8 sec., or more, ‘Eco ’ flashes, and then the digital
• Press c Jog switch in no-leak condition with Leak detection fiber
w
Econ display is turned off.
When a key operation is done after the display is turned off or when
(FD-F7M) fitted or no-liquid condition with Liquid detection fiber fitted
e
@ (FT-F9 M ). Then, ‘ @ ’ on the display moves from top left to top
right and from bottom right to bottom left (twice). turn
the collective teaching is carried out, the digital display lights up.
turn : This is the inverse mode of the digital display.
In the normal display condition, the display changes to the inverse display
• When teaching is accepted, the result of threshold value setting is and in the inverse condition, the display changes to the normal display.
9ood displayed.
• When c Jog switch is pressed, the set display blinks 3 times and is
r
In case stable sensing is possible: ‘ 9ood ’ on the display blinks
three times.
e
Econ confirmed.
Er-3 In case stable sensing is not possible: ‘Er-3 ' on the display blinks.
(Note 1)
• When z MODE key is pressed twice or for 1 sec., or more, the sen-
sor returns to RUN mode and the incident light intensity is displayed.
• If the teaching result is ‘9ood ’, the sensor returns to RUN mode au-
tomatically and the incident light intensity is shown on the display.
r
1234 • MODE indicator / RUN (green) lights up.
t
1234 • MODE indicator / RUN (green) lights up.
• The setting is complete.
• The setting is complete.
Note: The initial setting at the time of factory shipment is the light-up mode ( EcoF ).
Liquid (F9) mode • When x Jog switch is turned to the ‘+’ side or ‘–’ side, the output is
compulsory changed to ON or OFF.
4) The collective teaching transmits the information only in the direction of the arrow shown • Since the emitting element of the amplifier blinks, it is possible to
on the amplifier operation panel. The collective teaching is also possible from the middle of
the amplifiers mounted in cascade. Check the direction of the transmission before collec-
w
oFF check the fiber connected to the amplifier.
• When the output is compulsory changed to ON, the operation indi-
tive teaching is done.
cator (orange) lights up.
Direction of transmission
e
on • Press z MODE key to return the sensor to step q.
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
ALL
TEACH
RUN
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
OUT
DISP
ADJ
䢇 When MODE indicator / ADJ (yellow) lights up, the set threshold value can be fine • Press c Jog switch for 3 sec. or more.
adjusted. w
Auto (The sensor goes into the sensitivity setting condition.)
• MODE indicator / RUN (green) blinks.
Step Display Description
q
1234 • Press z MODE key to light up MODE indicator / ADJ (yellow).
Auto • When x Jog switch is turned to the ‘ +’ side or ‘–’ side, the display
and MODE indicator / RUN (green) blinks, and the sensitivity can be
selected.
• Turn x Jog switch to the ‘ +’ side, to increase the threshold value. Auto : Automatic sensitivity setting
w
1235 • Turn x Jog switch to the ‘ –’ side, to decrease the threshold value.
e
Lo After selecting the automatic sensitivity, the optimum sensi-
tivity is set by carrying out teaching.
Lo : Low sensitivity setting
• When c Jog switch is pressed, the changed threshold value blinks
e
1235 3 times and is confirmed. HI HI : High sensitivity setting
• When z MODE key is pressed 3 times, or for 2 sec., or more, the sensor re-
turns to the RUN mode and the incident light intensity is shown in the display. • When c Jog switch is pressed, the setting display blinks 3 times
r
1234 • MODE indicator / RUN (green) lights up.
r
Lo and is confirmed.
• The setting is complete.
Note: The adjustable area is limited as shown below. In order to adjust the threshold the outside the • MODE indicator / TEACH (green) lights up and ‘-F7- ’ or ‘-F9- ’ is
adjustable area, confirm it within the area once and then adjust it again.
t
-F7- displayed.
• After sensitivity selection, carry out the teaching.
Adjustable area in Leak (F7) mode: 70 to 110% Adjustable area in Liquid (F9) mode: 90 to 130% For the setting method of teaching, refer to ⁄0 INDIVIDUAL TEACH-
Sensing Liquid
q
-F9- TEACHING MODE or ⁄1 COLLECTIVE TEACHING MODE.
condition
Timer present
operation NO/NC
selection Liquid
absent
w
on • Press z MODE key to light up MODE indicator / OUT (yellow).
function
• Press c Jog switch for 3 sec., or more.
NC ON e
nc (The sensor goes into the NO/NC setting condition.)
( Normal
close ) • MODE indicator / RUN (green) blinks.
Normal
OFF
• When x Jog switch is turned to the ‘ +’ side or ‘–’ side, the display
NO
ON
nc and MODE indicator / RUN (green) blinks, and NO/NC can be cho-
( Normal
open ) OFF
r sen.
nc : Normal close (OFF in liquid absent condition.)
NC ON
no no : Normal open (OFF in liquid present condition.)
T T T
( Normal
)
Delay timer
close
OFF • When c Jog switch is pressed, setting display blinks 3 times and is
NO ON
t
no confirmed.
T T T
( Normal
open )
w
EcoF • Press z MODE key to light up MODE indicator / DISP (yellow).
⁄8 ERROR INDICATION
• Press c Jog switch for 3 sec., or more. 䢇 When an error is displayed, remedy as follows.
e
non (The sensor goes into the timer setting condition.)
• MODE indicator / RUN (green) blinks.
Error indication Cause
• Excessive current
Remedy
Er-1 flows due to a short- • Switch off the power supply and check the load.
non circuit.
• Check the installation condition of the fiber, or whether
• When x Jog switch is turned to the ‘+’ side or ‘–’ side, the display the fiber has come out, and then do teaching again.
• Press z MODE key to cancel ‘Er-3 ’. After the cancella-
10 and MODE indicator / RUN (green) blinks, and the timer period can
be chosen. Er-3 • The teaching is
abnormal.
tion, the sensor operates at the set value conditions be-
fore the error. However, in case the sensitivity selection
r non : Without timer function has been set to the automatic sensitivity setting
10 : 10ms timer (Auto ), the sensor operates at optimum sensitivity.
100 100 : 100ms timer
• The communica-
• Check if the amplifiers mounted in cascade are
1000 : 1,000ms timer
Er-5 tion is abnormal.
disconnected. After the confirmation, do the teach-
ing again.
1000
⁄9 DIMENSIONS
• When c Jog switch is pressed, setting display blinks 3 times and is
t
10 confirmed.
26.3
48.2 12
8.3 2.5
y
EcoF • The sensor returns to step w.
0.7
• When z MODE key is pressed twice or for 1 sec., or more, the sen- Output operation indicator (Orange) MODE key
sor returns to RUN mode and the incident light intensity is displayed.
u
1234 • MODE indicator / RUN (green) lights up.
Model indicator (Green)
Digital display (Red)
Jog switch
3 64.5 3
10 Communication
window 27.8
7
Emission
part
30.5
7 10.5
Receiving
7
part
3 3.95
13.5 36.5
Suitable for 35mm width DIN rail
Head Office
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-(0)568-33-7211 FAX: +81-(0)568-33-2631
Overseas Sales Dept.
Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591 PRINTED IN JAPAN