Parameter Reference

eNodeB
V100R005C00
Parameter Reference
Issue 06
Date 2012/09/20
HUAWEI TECHNOLOGIES CO., LTD.
Copyright Huawei Technologies Co., Ltd. 2012. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of H
Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All
products, services and features described in this document may not be within the purchase scope or the usage scope. Unl
specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without
guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the preparation of this
ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute
any kind, express or implied.
Huawei Technologies Co., Ltd.

Huawei Industrial Base
Bantian, Longgang
Address:
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: support@huawei.com
out prior written consent of Huawei
spective holders.
Huawei and the customer. All or part of the

ope or the usage scope. Unless otherwise
are provided "AS IS" without warranties,
ade in the preparation of this document to

document do not constitute a warranty of
Purpose
This document describes the MO parameters of eNodeB. For the details about the paramete
parameter list.
Intended Audience
This document is intended for:
Network planners
System engineers
Field engineers
Shift operators
Site maintainers
Network operators
Parameter Attribute Description

The following table describes the attributes of each parameter.
Parameter Attribute
MO
Parameter ID
Parameter Name
NE
MML Command
Meaning
IsKey
Mandatory
Dynamic Attribute
Feature ID
Feature Name
Value Type
GUI Value Range
Enumeration Number/Bit
Unit
Actual Value Range
Default Value
Recommended Value
Initial Value Source
Impact
Parameter Relationship
Access
Service Interrupted After Modification

Interruption Scope
Interruption Duration (min)
Caution
Validation of Modification
Impact on Radio Network
Performance
Introduced in Version
Attribute
Change History
For detailed parameter changes, see the release notes.
Issue Date
06 2012/9/20
05 2012/8/8
04 2012/6/29
03 2012/5/11
02 2012/4/28
01 2012/3/30
Draft B 2012/2/15
Draft A 2012/1/10
he MO parameters of eNodeB. For the details about the parameters related to northbound interface interconnectio
scription
es the attributes of each parameter.
Description
Managed object of NE.
A simple character string used for identifying a parameter.
Name of a parameter.
NEs on which the parameter is set.
Man Machine Language (MML) command related to the parameter.
Definition, purpose, and protocols of the parameter.
Whether the parameter is used to identify an MO instance.
Whether the parameter is mandatory for creating an MO instance.
Whether the parameter is dynamic for an MO. If the parameter is not dynamic, it can be added,
modified, or removed; if the parameter is dynamic, it cannot.
ID of the feature that uses the parameter.
Name of the feature that uses the parameter.
Type of a parameter value.
Range of the parameter values displayed on the GUI.
Enumeration number corresponding to the GUI value of a parameter of the enumeration type, or
bit
Unitposition corresponding
of a parameter to the GUIon
value displayed value of a parameter of the bit field type.
the GUI.
Range of the actual values corresponding to the parameter values displayed on the GUI.
Initial value assigned by the system for a parameter. For a mandatory parameter, no default value
is available. For a bit field parameter, if the value of a sub-parameter is ON, the bit representing
the sub-parameter is set to 1; if the value of a sub-parameter is OFF, the bit representing the sub-
parameter is set to 0. None indicates that no default value is available.
Generally, it is displayed on the configuration window of an ADD command but not displayed on
the configuration window of a MOD/RMV/DSP/LST command.
Parameter values recommended for different scenarios.

Source for the initial configuration of a parameter. The initial value source can be:
Radio planning (Internal planning): The parameter value comes from the radio network plan,
facilitating resource management on the NE.
Radio planning (Negotiation with the peer): The parameter value comes from the radio network
plan. The NE negotiates this value with the peer device to ensure successful interworking.
Transport planning (Internal planning): The parameter value comes from the transport network
plan, facilitating resource management on the NE.
Transport planning (Negotiation with the peer): The parameter value comes from the transport
network plan. The NE negotiates this value with the peer device to ensure successful
interworking.
Equipment planning: The parameter value comes from the equipment plan.
Engineering design: The parameter value comes from the algorithm or function design.
Default/recommended value: The parameter value uses the default or recommended value,
where the recommended value is preferential. The default/recommended value can be used in
most scenarios and adjusted for a specific scenario.
N/A: The parameter value is not required.
Parameter impact scope.
Relationship with other parameters. For example, to use this parameter, you need to set related
Whether this parameter is Read & Write or Read Only. If a parameter is not dynamic and is read
only, it can be set only when the MO is created and cannot be modified later. To modify the
parameter, you must delete the MO first and then create it again.
Whether modifying the parameter value interrupts the ongoing services.
Possible interruption scope.
Possible interruption duration (unit: minute).
Cautions to be taken during the modification.
How this parameter takes effect and whether the equipment needs to be restarted after the
Impact of the parameter on radio network performance.
Product version in which the parameter is introduced.

Whether the parameter is a radio parameter, a transport parameter, or an equipment parameter.
nges, see the release notes.
Description
This is the sixth official release.
This is the fifth official release.
This is the fourth official release.
This is the third official release.
This is the second official release.
This is the first official release.
This is the draft.
This is the draft.
rameters related to northbound interface interconnection, see the
parameter.
ed to the parameter.
eter.
O instance.
g an MO instance.
f the parameter is not dynamic, it can be added,
mic, it cannot.
e GUI.
value of a parameter of the enumeration type, or
.parameter of the bit field type.
e parameter values displayed on the GUI.
meter. For a mandatory parameter, no default value
e of a sub-parameter is ON, the bit representing
ub-parameter is OFF, the bit representing the sub-
efault value is available.
indow of an ADD command but not displayed on
LST command.
cenarios.
er. The initial value source can be:
ter value comes from the radio network plan,
parameter value comes from the radio network

r device to ensure successful interworking.
ameter value comes from the transport network
NE.
The parameter value comes from the transport
h the peer device to ensure successful
es from the equipment plan.

es from the algorithm or function design.
lue uses the default or recommended value,
The default/recommended value can be used in
ario.
e, to use this parameter, you need to set related

d Only. If a parameter is not dynamic and is read
and cannot be modified later. To modify the
en create it again.
pts the ongoing services.
e equipment needs to be restarted after the

rmance.
duced.
transport parameter, or an equipment parameter.
MO Parameter ID Parameter Name NE MML Command
ADD BFANT
DSP BFANT
BFANT DEVICENO Device No. eNodeB LST BFANT
MOD BFANT
RMV BFANT
ADD BFANT
Connect RRU MOD BFANT
BFANT CONNCN eNodeB
cabinet No. DSP BFANT
LST BFANT
ADD BFANT
Connect RRU MOD BFANT
BFANT CONNSRN eNodeB
subrack No. DSP BFANT
LST BFANT
ADD BFANT
Connect RRU slot MOD BFANT
BFANT CONNSN eNodeB
No. DSP BFANT
LST BFANT
ADD BFANT
Antenna model MOD BFANT
BFANT MODELNO eNodeB
number DSP BFANT
LST BFANT
ADD BFANT
MOD BFANT
BFANT TILT Tilt eNodeB
DSP BFANT
LST BFANT
ADD BFANT
MOD BFANT
BFANT BEAMWIDTH Beamwidth eNodeB
DSP BFANT
LST BFANT
ADD BFANT
MOD BFANT
BFANT Band Band eNodeB
DSP BFANT
LST BFANT
ADD BFANT
BFANT TYPE Antenna Type eNodeB MOD BFANT
LST BFANT
BFANT POLARMODE Polar Mode eNodeB DSP BFANT
Element Beamform
BFANT ELMTBMWTH eNodeB None
Width
BFANT AntPortNum Number of Port eNodeB DSP BFANT

Amplitude Offset of
BFANT CRS2Amp1 Physical Port 1 for eNodeB DSP BFANT
CRS2
Phase of Physical
BFANT CRS2Pha1 eNodeB DSP BFANT
Port 1 for CRS2
Amplitude Offset of
CRS2
Phase of Physical
Port 2 for CRS2
Amplitude Offset of
CRS2
Phase of Physical
Port 3 for CRS2
Amplitude Offset of
CRS2
Phase of Physical
Port 4 for CRS2
Amplitude Offset of
CRS4
Phase of Physical
Port 1 for CRS4
Amplitude Offset of
CRS4
Phase of Physical
Port 2 for CRS4
MOD ENODEB
eNodeB ENODEBID eNodeB ID eNodeB DSP ENODEB
LST ENODEB
MOD ENODEB
eNodeB NAME eNodeB name eNodeB
LST ENODEB
MOD ENODEB
eNodeB ENBTYPE eNodeB type eNodeB
LST ENODEB
AUTOPOWEROFF Auto power control MOD ENODEB

eNodeB eNodeB
SWITCH switch LST ENODEB
MOD ENODEB
eNodeB POWEROFFTIME Auto power off time eNodeB
LST ENODEB
MOD ENODEB
eNodeB POWERONTIME Auto power on time eNodeB
LST ENODEB
MOD ENODEB
eNodeB LONGITUDE Longitude eNodeB
LST ENODEB
MOD ENODEB
eNodeB LATITUDE Latitude eNodeB
LST ENODEB
Electronic Serial
eNodeB ElectriSerialNo eNodeB DSP ENODEB
Number
eNodeB LicenseState LicenseState eNodeB DSP ENODEB

eNodeB
eNodeB AutoPoweroffStatus eNodeB DSP ENODEB
autopoweroff status
MOD ENODEB
eNodeB LOCATION Site Location eNodeB
LST ENODEB
Geo-coordinate MOD ENODEB

eNodeB GCDF eNodeB
data format LST ENODEB
LATITUDESECFOR Latitude with MOD ENODEB

eNodeB eNodeB
MAT second format LST ENODEB
LONGITUDESECF Longitude with MOD ENODEB
eNodeB eNodeB
ORMAT second format LST ENODEB
MOD ENODEB
eNodeB PROTOCOL Protocol Type eNodeB
LST ENODEB
LST KPIALARM
KPIALARM KPITYPE KPITYPE eNodeB
MOD KPIALARM
MOD KPIALARM
KPIALARM REPORTSWITCH Report Switch eNodeB
LST KPIALARM
MOD KPIALARM
KPIALARM FLTTHRESHOLD FltThreshold eNodeB
LST KPIALARM
MOD KPIALARM
KPIALARM RESTHRESHOLD ResThreshold eNodeB
LST KPIALARM
MOD KPIALARM
KPIALARM MINCHECKTIMES MinCheckTimes eNodeB
LST KPIALARM
MOD KPIALARM
KPIALARM DETECTPERIOD DetectPeriod eNodeB
LST KPIALARM
DETECTBEGINTIM MOD KPIALARM

KPIALARM DetectBeginTime eNodeB
E LST KPIALARM
DETECTPERIODN MOD KPIALARM

KPIALARM DetectPeriodNum eNodeB
UM LST KPIALARM
ADD SECTOR
DSP SECTOR
Sector SECN Sector No. eNodeB LST SECTOR
MOD SECTOR
RMV SECTOR
ADD SECTOR
Sector LONGITUDE Longitude eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Sector LATITUDE Latitude eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Sector ANTM Antenna mode eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Sector SECM Sector mode eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Sector COMBM CombMode eNodeB MOD SECTOR
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
Sector CN1 eNodeB MOD SECTOR
antenna port 1 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
Sector SRN1 eNodeB MOD SECTOR
antenna port 1 is
LST SECTOR
located
Slot No. of the RRU ADD SECTOR

Sector SN1 where antenna port eNodeB MOD SECTOR
1 is located LST SECTOR
ADD SECTOR
Port No. of antenna
Sector PN1 eNodeB MOD SECTOR
connector 1
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 2 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 2 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 2
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 3 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 3 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 3
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 4 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 4 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 4
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 5 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 5 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 5
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 6 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 6 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 6
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 7 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 7 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 7
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 8 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 8 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 8
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 9 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 9 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 9
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 10 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 10 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 10
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 11 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 11 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 11
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 12 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 12 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 12
LST SECTOR
ADD SECTOR
Sector SECTORNAME Sector name eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Sector ALTITUDE Altitude eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
UNCERTSEMIMAJ
Sector UncertSemiMajor eNodeB MOD SECTOR
OR
LST SECTOR
ADD SECTOR
UNCERTSEMIMIN
Sector UncertSemiMinor eNodeB MOD SECTOR
OR
LST SECTOR
ADD SECTOR
ORIENTOFMAJOR
Sector OrientOfMajorAxis eNodeB MOD SECTOR
AXIS
LST SECTOR
ADD SECTOR
Sector UNCERTALTITUDE UncertAltitude eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Sector CONFIDENCE Confidence eNodeB MOD SECTOR
LST SECTOR
ADD SECTOR
Geo-coordinate
Sector GCDF eNodeB MOD SECTOR
data format
LST SECTOR
ADD SECTOR
ANTLATITUDESEC Antenna latitude
Sector eNodeB MOD SECTOR
FORMAT with second format
LST SECTOR
ADD SECTOR
ANTLONGITUDES Antenna longitude
Sector eNodeB MOD SECTOR
ECFORMAT with second format
LST SECTOR
ADD SECTOR
Sector OMNIFLAG Omni Mode eNodeB MOD SECTOR
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 13 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 13 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 13
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 14 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 14 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 14
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 15 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 15 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 15
LST SECTOR
Cabinet No. of the

ADD SECTOR
RRU where
antenna port 16 is
LST SECTOR
located
Subrack No. of the

ADD SECTOR
RRU where
antenna port 16 is
LST SECTOR
located

ADD SECTOR
Port No. of antenna
connector 16
LST SECTOR
Maximum transmit
Sector MaxTxPower power of each TX eNodeB DSP SECTOR
channel
Sector LicState License state eNodeB DSP SECTOR
RXFrequencyRang RX Frequency
Sector eNodeB DSP SECTOR
e Range
TXFrequencyRang TX Frequency
Sector eNodeB DSP SECTOR
e Range
SET
WEBLOGINPOLIC
WebLMT Login Y
WEBLOGINPOLICY POLICY eNodeB
Policy LST
WEBLOGINPOLIC
Y
DLD ALDSW
ALD DEVICENO Device No. eNodeB DSP ALDVER
RST ALD
ALD RtmVendorCode Actual Vendor Code eNodeB None
Actual Device Serial

ALD RtmDeviceSerialNo eNodeB DSP ALDVER
No.
ALD DEVICENAME Device Name eNodeB DSP ALDVER
DLD ALDSW
DLD RETCFGDATA
Control Port
ALD CTRLCN eNodeB DSP ALDVER
Cabinet No.
RST ALD
SCN ALD
DLD ALDSW
DLD RETCFGDATA
Control Port
ALD CTRLSRN eNodeB DSP ALDVER
Subrack No.
RST ALD
SCN ALD
DLD ALDSW
DLD RETCFGDATA
Control Port Slot
ALD CTRLSN eNodeB DSP ALDVER
No.
RST ALD
SCN ALD
ALD ProtocolVersion Protocol Version eNodeB DSP ALDVER
RtmTotalSubunitNu Actual Subunit

ALD eNodeB None
m Number
ALD VENDORCODE Vendor Code eNodeB None
ALD SERIALNO Serial No. eNodeB None
ALD HardwareVersion Hardware Version eNodeB DSP ALDVER
ALD SoftwareVersion Software Version eNodeB DSP ALDVER
ALD DeviceModel Device Model eNodeB DSP ALDVER
ALD DeviceType Device Type eNodeB DSP ALDVER

ALD CtrlPortNo Control Port No. eNodeB None
DSP
ANTENNAPORT
LST
AntennaPort CN Cabinet No. eNodeB
ANTENNAPORT
MOD
ANTENNAPORT
DSP
ANTENNAPORT
LST
AntennaPort SRN Subrack No. eNodeB
ANTENNAPORT
MOD
ANTENNAPORT
DSP
ANTENNAPORT
LST
AntennaPort SN Slot No. eNodeB
ANTENNAPORT
MOD
ANTENNAPORT
DSP
ANTENNAPORT
LST
AntennaPort PN Port No. eNodeB
ANTENNAPORT
MOD
ANTENNAPORT
MOD
ANTENNAPORT
AntennaPort FEEDERLENGTH Feeder Length eNodeB
LST
ANTENNAPORT
MOD
TMA Downlink ANTENNAPORT
AntennaPort DLDELAY eNodeB
Delay LST
ANTENNAPORT
MOD
ANTENNAPORT
AntennaPort DUDELAY TMA Uplink Delay eNodeB
LST
ANTENNAPORT
MOD
ANTENNAPORT
AntennaPort PWRSWITCH ALD Power Switch eNodeB
LST
ANTENNAPORT
MOD
Current Alarm ANTENNAPORT
AntennaPort THRESHOLDTYPE eNodeB
Threshold Type LST
ANTENNAPORT
MOD
Undercurrent Alarm ANTENNAPORT
AntennaPort UOTHD eNodeB
Occur Threshold LST
ANTENNAPORT
MOD
Undercurrent Alarm ANTENNAPORT
AntennaPort UCTHD eNodeB
Clear Threshold LST
ANTENNAPORT
MOD
Overcurrent Alarm ANTENNAPORT
AntennaPort OOTHD eNodeB
Occur Threshold LST
ANTENNAPORT
MOD
Overcurrent Alarm ANTENNAPORT
AntennaPort OCTHD eNodeB
Clear Threshold LST
ANTENNAPORT
DSP
AntennaPort ALDCurrValue ALD Current Value eNodeB
ANTENNAPORT
ALD Actual Power DSP

AntennaPort ALDRtmPwrSwitch eNodeB
Switch ANTENNAPORT
ADD RET
MOD RET
RET RETTYPE RET Type eNodeB
MOD RETTILT
LST RET
ADD RET
RET POLARTYPE Polar Type eNodeB MOD RET
LST RET
ADD RET
RET SCENARIO Antenna Scenario eNodeB MOD RET
LST RET
ADD RET
RET Subunit
RET SUBUNITNUM eNodeB MOD RET
Number
LST RET
RET RETCLASS RET Class eNodeB MOD RETTILT
ADD RET
DSP RET
RET DEVICENO Device No. eNodeB LST RET
MOD RET
RMV RET
RET RtmVendorCode Actual Vendor Code eNodeB DSP RET

RET RtmDeviceSerialNo eNodeB DSP RET
No.
ADD RET
RET DEVICENAME Device Name eNodeB MOD RET
LST RET
ADD RET
Control Port MOD RET
RET CTRLCN eNodeB
Cabinet No. DSP RET
LST RET
ADD RET
Control Port MOD RET
RET CTRLSRN eNodeB
Subrack No. DSP RET
LST RET
ADD RET
Control Port Slot MOD RET
RET CTRLSN eNodeB
No. DSP RET
LST RET
RET ProtocolVersion Protocol Version eNodeB None

RET eNodeB DSP RET
m Number
ADD RET
RET VENDORCODE Vendor Code eNodeB MOD RET
LST RET
ADD RET
RET SERIALNO Serial No. eNodeB MOD RET
LST RET
RET HardwareVersion Hardware Version eNodeB None
RET SoftwareVersion Software Version eNodeB None
RET DeviceModel Device Model eNodeB None
RET DeviceType Device Type eNodeB None

RET CtrlPortNo Control Port No. eNodeB DSP RET
DSP
RETDEVICEDATA
LST
RetDeviceData DEVICENO Device No. eNodeB
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RETDEVICEDATA
LST
RetDeviceData SUBUNITNO Subunit No. eNodeB
RETDEVICEDATA
MOD
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RetDeviceData BEARING Antenna Bearing eNodeB
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
Antenna Model DSP
RetDeviceData MODELNO eNodeB
Number RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RetDeviceData BSID Base Station ID eNodeB
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
RetDeviceData BEAMWIDTH1 Beamwidth1 eNodeB
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
RetDeviceData GAIN1 Gain1 eNodeB
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RetDeviceData DATE Installation Date eNodeB
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
Installed DSP
RetDeviceData TILT eNodeB
Mechanical Tilt RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RetDeviceData INSTALLERID Installer's ID eNodeB
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
RetDeviceData BAND1 Band1 eNodeB
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RetDeviceData SECTORID Sector ID eNodeB
RETDEVICEDATA
LST
RETDEVICEDATA
MOD
RETDEVICEDATA
DSP
RetDeviceData SERIALNO Antenna Serial No. eNodeB
RETDEVICEDATA
LST
RETDEVICEDATA
DSP
RetDeviceData MaxTilt Max Tilt eNodeB
RETDEVICEDATA
DSP
RetDeviceData MinTilt Min Tilt eNodeB
RETDEVICEDATA
RtmOpBandCodes DSP
RetDeviceData Band1 eNodeB
1 RETDEVICEDATA
RtmOpBandCodes DSP
2 RETDEVICEDATA
RtmOpBandCodes DSP
3 RETDEVICEDATA
RtmOpBandCodes DSP
4 RETDEVICEDATA
DSP
RetDeviceData RtmBeamWidth1 Beamwidth1 eNodeB
RETDEVICEDATA
DSP
RETDEVICEDATA
DSP
RETDEVICEDATA
DSP
RETDEVICEDATA
DSP
RetDeviceData RtmGainValue1 Gain1 eNodeB
RETDEVICEDATA
DSP
RETDEVICEDATA
DSP
RETDEVICEDATA
DSP
RETDEVICEDATA
DSP RETPORT
RetPort CN Cabinet No. eNodeB LST RETPORT
MOD RETPORT
DSP RETPORT
RetPort SRN Subrack No. eNodeB LST RETPORT
MOD RETPORT
DSP RETPORT
RetPort SN Slot No. eNodeB LST RETPORT
MOD RETPORT
DSP RETPORT
RetPort PN Port No. eNodeB LST RETPORT
MOD RETPORT
MOD RETPORT
RetPort PWRSWITCH ALD Power Switch eNodeB
LST RETPORT
Current Alarm MOD RETPORT
RetPort THRESHOLDTYPE eNodeB
Threshold LST RETPORT
Undercurrent Alarm MOD RETPORT

RetPort UOTHD eNodeB
Occur Threshold LST RETPORT
Undercurrent Alarm MOD RETPORT
RetPort UCTHD eNodeB
Clear Threshold LST RETPORT
Overcurrent Alarm MOD RETPORT

RetPort OOTHD eNodeB
Occur Threshold LST RETPORT
Overcurrent Alarm MOD RETPORT
RetPort OCTHD eNodeB
Clear Threshold LST RETPORT
RetPort ALDCurrValue ALD Current Value eNodeB DSP RETPORT
ALD Actual Power

RetPort ALDRtmPwrSwitch eNodeB DSP RETPORT
Switch
CLB RET
DLD RETCFGDATA
DSP RETSUBUNIT
RETSubunit DEVICENO Device No. eNodeB LST RETSUBUNIT
MOD
RETSUBUNIT
MOD RETTILT
CLB RET
DLD RETCFGDATA
DSP RETSUBUNIT
RETSubunit SUBUNITNO Subunit No. eNodeB
LST RETSUBUNIT
MOD
RETSUBUNIT
RETSubunit Status Online Status eNodeB DSP RETSUBUNIT
RETSubunit RtmTilt Actual Tilt eNodeB DSP RETSUBUNIT
RETSubunit RtmSectorId Sector Id eNodeB DSP RETSUBUNIT
MOD
Connect Port 1
RETSubunit CONNCN1 eNodeB RETSUBUNIT
Cabinet No.
LST RETSUBUNIT
MOD
Connect Port 1
RETSubunit CONNSRN1 eNodeB RETSUBUNIT
Subrack No.
LST RETSUBUNIT
MOD
Connect Port 1 Slot
RETSubunit CONNSN1 eNodeB RETSUBUNIT
No.
LST RETSUBUNIT
MOD
Connect Port 1 Port
RETSubunit CONNPN1 eNodeB RETSUBUNIT
No.
LST RETSUBUNIT
MOD
Connect Port 2
RETSubunit CONNCN2 eNodeB RETSUBUNIT
Cabinet No.
LST RETSUBUNIT
MOD
Connect Port 2
RETSubunit CONNSRN2 eNodeB RETSUBUNIT
Subrack No.
LST RETSUBUNIT
MOD
Connect Port 2 Slot
RETSubunit CONNSN2 eNodeB RETSUBUNIT
No.
LST RETSUBUNIT
MOD
Connect Port 2 Port
RETSubunit CONNPN2 eNodeB RETSUBUNIT
No.
LST RETSUBUNIT
MOD
RETSUBUNIT
RETSubunit TILT Tilt eNodeB
MOD RETTILT
LST RETSUBUNIT
MOD
Tilt Alarm Error
RETSubunit AER eNodeB RETSUBUNIT
Range
LST RETSUBUNIT
MOD
RETSUBUNIT
RETSubunit SUBNAME Subunit Name eNodeB
MOD RETTILT
LST RETSUBUNIT
ADD TMA
TMA Subunit
TMA SUBUNITNUM eNodeB MOD TMA
Number
LST TMA
ADD TMA
DSP TMA
TMA DEVICENO Device No. eNodeB LST TMA
MOD TMA
RMV TMA
TMA RtmVendorCode Actual Vendor Code eNodeB DSP TMA

TMA RtmDeviceSerialNo eNodeB DSP TMA
No.
ADD TMA
TMA DEVICENAME Device Name eNodeB MOD TMA
LST TMA
ADD TMA
Control Port MOD TMA
TMA CTRLCN eNodeB
Cabinet No. DSP TMA
LST TMA
ADD TMA
Control Port MOD TMA
TMA CTRLSRN eNodeB
Subrack No. DSP TMA
LST TMA
ADD TMA
Control Port Slot MOD TMA
TMA CTRLSN eNodeB
No. DSP TMA
LST TMA
TMA ProtocolVersion Protocol Version eNodeB None

TMA eNodeB DSP TMA
m Number
ADD TMA
TMA VENDORCODE Vendor Code eNodeB MOD TMA
LST TMA
ADD TMA
TMA SERIALNO Serial No. eNodeB MOD TMA
LST TMA
TMA HardwareVersion Hardware Version eNodeB None
TMA SoftwareVersion Software Version eNodeB None
TMA DeviceModel Device Model eNodeB None
TMA DeviceType Device Type eNodeB None

TMA CtrlPortNo Control Port No. eNodeB DSP TMA
DSP
TMADEVICEDATA
LST
TMADeviceData DEVICENO Device No. eNodeB
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADEVICEDATA
LST
TMADeviceData SUBUNITNO Subunit No. eNodeB
TMADEVICEDATA
MOD
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADeviceData BEARING Antenna Bearing eNodeB
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADeviceData BSID Base Station ID eNodeB
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
TMADeviceData BEAMWIDTH1 Beamwidth1 eNodeB
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
TMADeviceData GAIN1 Gain1 eNodeB
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADeviceData DATE Installation Date eNodeB
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
Installed DSP
TMADeviceData TILT eNodeB
Mechanical Tilt TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADeviceData INSTALLERID Installer's ID eNodeB
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
TMADeviceData BAND1 Band1 eNodeB
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADeviceData SECTORID Sector ID eNodeB
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
DSP
TMADeviceData SERIALNO Serial No. eNodeB
TMADEVICEDATA
LST
TMADEVICEDATA
MOD
TMADEVICEDATA
Connect Antenna DSP
TMADeviceData MODELNO eNodeB
Model Number TMADEVICEDATA
LST
TMADEVICEDATA
Max Supported DSP

TMADeviceData MaxSupportedGain eNodeB
Gain TMADEVICEDATA
DSP
TMADeviceData MinSupportedGain Min Supported Gain eNodeB
TMADEVICEDATA
RtmTmaSubunitTyp DSP
TMADeviceData Real Subunit type eNodeB
e TMADEVICEDATA
RtmTmaGainResol Real Gain DSP

TMADeviceData eNodeB
ution Resolution TMADEVICEDATA
DSP
TMADeviceData RtmOpBandCode1 Band1 eNodeB
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADeviceData RtmBeamWidth1 Beamwidth1 eNodeB
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADeviceData RtmGainValue1 Gain1 eNodeB
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADEVICEDATA
DSP
TMADEVICEDATA
RtmTmaRxMinFreB Real Received Min DSP

and Frequency Band TMADEVICEDATA
RtmTmaTxMaxFre Real Transmit Max DSP

Band Frequency Band TMADEVICEDATA
RtmTmaTxMinFreB Real Transmit Min DSP

and Frequency Band TMADEVICEDATA
RtmTmaRxMaxFre Real Received Max DSP

Band Frequency Band TMADEVICEDATA
DSP TMASUBUNIT
LST TMASUBUNIT
TMASubunit DEVICENO Device No. eNodeB
MOD
TMASUBUNIT
DSP TMASUBUNIT
LST TMASUBUNIT
TMASubunit SUBUNITNO Subunit No. eNodeB
MOD
TMASUBUNIT
TMASubunit RtmSectorId Actual Sector ID eNodeB DSP TMASUBUNIT
TMASubunit RtmGain Actual Gain eNodeB DSP TMASUBUNIT
TMASubunit RtmMode Actual Mode eNodeB DSP TMASUBUNIT

TMASubunit Status Online Status eNodeB DSP TMASUBUNIT
MOD
TMASubunit CONNPN Connect Port No. eNodeB TMASUBUNIT
LST TMASUBUNIT
MOD
Connect Port
TMASubunit CONNCN eNodeB TMASUBUNIT
Cabinet No.
LST TMASUBUNIT
MOD
Connect Port Slot
TMASubunit CONNSN eNodeB TMASUBUNIT
No.
LST TMASUBUNIT
MOD
Connect Port
TMASubunit CONNSRN eNodeB TMASUBUNIT
Subrack No.
LST TMASUBUNIT
MOD
TMASubunit GAIN Gain eNodeB TMASUBUNIT
LST TMASUBUNIT
MOD
TMASubunit MODE Mode eNodeB TMASUBUNIT
LST TMASUBUNIT
VAntennaPort CONNCN Cabinet No. eNodeB None
VAntennaPort CONNSRN Subrack No. eNodeB None
VAntennaPort CONNSN Slot No. eNodeB None
VAntennaPort PN Port No. eNodeB None
LST VRET
VRET DEVICENO Device No. eNodeB
MOD VRET
VRET CONNCN Cabinet No. eNodeB LST VRET

VRET CONNSRN Subrack No. eNodeB LST VRET
VRET CONNSN Slot No. eNodeB LST VRET
MOD VRET
VRET DEVICENAME Device Name eNodeB
LST VRET
SUBUNITQUANTIT MOD VRET

VRET Subunit Quantity eNodeB
Y LST VRET
VRETSubunit CONNCN Cabinet No. eNodeB None
MOD
VRETSUBUNIT
DSP
VRETSubunit CONNPN1 Connected Port 1 eNodeB
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSUBUNIT
VRETSubunit SUBNAME Device Name eNodeB
LST
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSubunit DEVICENO Device No. eNodeB
VRETSUBUNIT
MOD
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSubunit POLARTYPE1 Polar Type1 eNodeB
VRETSUBUNIT
LST
VRETSUBUNIT
VRETSubunit CONNSN Slot No. eNodeB None
VRETSubunit CONNSRN Subrack No. eNodeB None
DSP
VRETSUBUNIT
LST
VRETSubunit SUBUNITNO Subunit No. eNodeB
VRETSUBUNIT
MOD
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD RETTILT
MOD
VRETSUBUNIT
VRETSubunit DLTILT Downlink Tilt eNodeB DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD RETTILT
MOD
VRETSUBUNIT
VRETSubunit ULTILT Uplink Tilt eNodeB DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSUBUNIT
DSP
VRETSUBUNIT
LST
VRETSUBUNIT
MOD
VRETSubunit PORTNUM PORTNUM eNodeB
VRETSUBUNIT
ADD CTRLLNK
LST CTRLLNK
CTRLLNK LN Local Link No. eNodeB
MOD CTRLLNK
RMV CTRLLNK
ADD CTRLLNK
DSP
CTRLLNK CN Local Cabinet No. eNodeB CTRLLNKSTAT
MOD CTRLLNK
LST CTRLLNK
ADD CTRLLNK
DSP
CTRLLNK SRN Local Subrack No. eNodeB CTRLLNKSTAT
MOD CTRLLNK
LST CTRLLNK
ADD CTRLLNK
DSP
CTRLLNK SN Local Slot No. eNodeB CTRLLNKSTAT
MOD CTRLLNK
LST CTRLLNK
ADD CTRLLNK
CTRLLNK UPCN Upper Cabinet No. eNodeB MOD CTRLLNK
LST CTRLLNK
ADD CTRLLNK
CTRLLNK UPSRN Upper Subrack No. eNodeB MOD CTRLLNK
LST CTRLLNK
ADD CTRLLNK
CTRLLNK UPSN Upper Slot No. eNodeB MOD CTRLLNK
LST CTRLLNK
ADD CTRLLNK
CTRLLNK UPPT Upper Port No. eNodeB MOD CTRLLNK
LST CTRLLNK
DSP
CTRLLNK PT Port No. eNodeB
CTRLLNKSTAT
Measurement Start DSP

CTRLLNK TIMESTART eNodeB
Time CTRLLNKSTAT
ONEDAYERRPKG 1 Day Error DSP

CTRLLNK eNodeB
NUM Package Number CTRLLNKSTAT
ONEDAYERRPKG 1 Day Error DSP
CTRLLNK eNodeB
RATE Package Rate CTRLLNKSTAT
ONEDAYERRLOS DSP
CTRLLNK 1 Day LOS Rate eNodeB
RATE CTRLLNKSTAT
ONEDAYERRLOST DSP
CTRLLNK 1 Day LOS time eNodeB
IME CTRLLNKSTAT
ONEHOURERRPK 1 Hour Error DSP

CTRLLNK eNodeB
GNUM Package Number CTRLLNKSTAT
ONEHOURERRPK 1 Hour Error DSP

CTRLLNK eNodeB
GRATE Package Rate CTRLLNKSTAT
ONEHOURERRLO DSP
CTRLLNK 1 Hour LOS Rate eNodeB
SRATE CTRLLNKSTAT
ONEHOURERRLO DSP
CTRLLNK 1 Hour LOS Time eNodeB
STIME CTRLLNKSTAT
ONEWEEKERRPK 1 Week Error DSP
CTRLLNK eNodeB
GNUM Package Number CTRLLNKSTAT
ONEWEEKERRPK 1 Week Error DSP

CTRLLNK eNodeB
GRATE Package Rate CTRLLNKSTAT
ONEWEEKERRLO DSP
CTRLLNK 1 Week LOS Rate eNodeB
SRATE CTRLLNKSTAT
ONEWEEKERRLO DSP
CTRLLNK 1 Week LOS time eNodeB
STIME CTRLLNKSTAT
TOTALERRPKGNU Total Error Package DSP

CTRLLNK eNodeB
M Number CTRLLNKSTAT
DSP
CTRLLNK TOTALLOSTIME Total LOS Time eNodeB
CTRLLNKSTAT
Total Measurement DSP

CTRLLNK TOTALTSTIME eNodeB
Time CTRLLNKSTAT
Total Receive DSP

CTRLLNK TOTALRXPKGNUM eNodeB
Package Number CTRLLNKSTAT
ADD BITS
DSP BITS
BITS BN BITS Clock No. eNodeB MOD BITS
RMV BITS
LST BITS
ADD BITS
BITS CN Cabinet No. eNodeB
LST BITS
ADD BITS
BITS SRN Subrack No. eNodeB
LST BITS
ADD BITS
BITS SN Slot No. eNodeB
LST BITS
BITS ActiveState Link Active State eNodeB DSP BITS
BITS AvailableState Link Available State eNodeB DSP BITS
ADD BITS
BITS PRI Priority eNodeB MOD BITS
LST BITS
ADD LINECLK
DSP LINECLK
LineClk LN Line Clock No. eNodeB MOD LINECLK
RMV LINECLK
LST LINECLK
ADD LINECLK
LineClk CN Cabinet No. eNodeB
LST LINECLK
ADD LINECLK
LineClk SRN Subrack No. eNodeB
LST LINECLK
ADD LINECLK
LineClk SN Slot No. eNodeB
LST LINECLK
ADD LINECLK
LineClk PN Port No. eNodeB DSP LINECLK
LST LINECLK
LineClk ActiveState Link Active State eNodeB DSP LINECLK
LineClk AvailableState Link Available State eNodeB DSP LINECLK
ADD LINECLK
LineClk PRI Priority eNodeB MOD LINECLK
LST LINECLK
ADD PEERCLK
DSP PEERCLK
PeerClk PN Peer Clock No. eNodeB
RMV PEERCLK
LST PEERCLK
ADD PEERCLK
PeerClk PS Peer Standard eNodeB
LST PEERCLK
PeerClk ActiveState Link Active State eNodeB DSP PEERCLK
PeerClk AvailableState Link Available State eNodeB DSP PEERCLK
ADD TOD
DSP TOD
TOD TN TOD Clock No. eNodeB MOD TOD
RMV TOD
LST TOD
ADD TOD
TOD TYPE TOD Type eNodeB DSP TOD
LST TOD
ADD TOD
TOD CN Cabinet No. eNodeB
LST TOD
ADD TOD
TOD SRN Subrack No. eNodeB
LST TOD
ADD TOD
TOD SN Slot No. eNodeB
LST TOD
ADD TOD
TOD CABLETYPE Cable Type eNodeB MOD TOD
LST TOD
ADD TOD
TOD CABLE_LEN Cable Length eNodeB MOD TOD
LST TOD
TOD ActiveState Link Active State eNodeB DSP TOD
TOD AvailableState Link Available State eNodeB DSP TOD
TOD DELAY Delay eNodeB DSP TOD

ADD TOD
TOD PRI Priority eNodeB MOD TOD
LST TOD
ADD GPS
DSP GPS
MOD GPS
GPS GN GPS Clock No. eNodeB
RMV GPS
RST SATCARD
LST GPS
ADD GPS
GPS CN Cabinet No. eNodeB
LST GPS
ADD GPS
GPS SRN Subrack No. eNodeB
LST GPS
ADD GPS
GPS SN Slot No. eNodeB
LST GPS
MOD GPSPOS
GPS WPOS Way to Get Position eNodeB
LST GPSPOS
MOD GPSPOS
GPS LONG Antenna Longitude eNodeB DSP GPS
LST GPSPOS
MOD GPSPOS
GPS LAT Antenna Latitude eNodeB DSP GPS
LST GPSPOS
MOD GPSPOS
GPS ALT Antenna Altitude eNodeB DSP GPS
LST GPSPOS
MOD GPSPOS
GPS AGL Antenna Angle eNodeB DSP GPS
LST GPSPOS
GPS DELAY Feeder Delay eNodeB DSP GPS
MOD GPSPOS
GPS DURATION Duration eNodeB
LST GPSPOS
MOD GPSPOS
GPS PRECISION Precision eNodeB
LST GPSPOS
ADD GPS
GPS CABLETYPE Cable Type eNodeB MOD GPS
LST GPS
ADD GPS
GPS CABLE_LEN Cable Length eNodeB MOD GPS
LST GPS
GPS GpsVersion GPS Version eNodeB DSP GPS
GPS PosFix GPS Position Fixed eNodeB DSP GPS
GPS Almnac Almanac Validity eNodeB DSP GPS
GPS PosSolu Position Solution eNodeB DSP GPS
GPS FixPos Fixed Position eNodeB DSP GPS

GPS ClkSteer Clock Steering eNodeB DSP GPS
GPS ClkMode Clock Model Validity eNodeB DSP GPS
GLONASS
GPS GlonassNum eNodeB DSP GPS
Satellites Traced
GPS GpsCardState GPS Card State eNodeB DSP GPS

GPS GpsCardType GPS Card Type eNodeB DSP GPS
GPS Satellites
GPS GpsNum eNodeB DSP GPS
Traced
ADD GPS
MOD GPS
GPS MODE GPS Work Mode eNodeB
DSP GPS
LST GPS
COMPASS
GPS CompassNum eNodeB DSP GPS
Satellites Traced
GPS ActiveState Link Active State eNodeB DSP GPS
ADD GPS
GPS PRI Priority eNodeB MOD GPS
LST GPS
ADD IPCLKLINK
DSP IPCLKLINK
DSP PRICLASS
RMV IPCLKLINK
IPCLKLNK LN IP Clock No. eNodeB SET
CLASSIDENTIFY
SET PRICLASS
LST IPCLKLINK
LST PRICLASS
ADD IPCLKLINK
IPCLKLNK ICPT Protocol Type eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK CN Cabinet No. eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK SRN Subrack No. eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK SN Slot No. eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK CIP Client IPv4 eNodeB DSP IPCLKLINK
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK SIP Server IPv4 eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK DM Domain eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK DELAYTYPE Delay Type eNodeB
LST IPCLKLINK
SET
Priority Clock Class
IPCLKLNK CLASSIDENTIFY eNodeB CLASSIDENTIFY
Identify Flag
DSP PRICLASS
SET PRICLASS
Priority Clock
IPCLKLNK CLASS0 eNodeB DSP PRICLASS
Class0
LST PRICLASS
SET PRICLASS
Priority Clock
Class1
LST PRICLASS
SET PRICLASS
Priority Clock
Class2
LST PRICLASS
SET PRICLASS
Priority Clock
Class3
LST PRICLASS
Current Priority
IPCLKLNK CurClass eNodeB DSP PRICLASS
Clock Class
Clock Source ADD IPCLKLINK

IPCLKLNK MACMODE eNodeB
Specified or Not LST IPCLKLINK
ADD IPCLKLINK
Clock Source MAC
IPCLKLNK CLKMAC eNodeB DSP IPCLKLINK
Address
LST IPCLKLINK
IPCLKLNK ActiveState Link Active State eNodeB DSP IPCLKLINK
IPCLKLNK AvailableState Link Available State eNodeB DSP IPCLKLINK
ADD IPCLKLINK
IPCLKLNK CNM Clock Net Mode eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK CMPST Compensation eNodeB
LST IPCLKLINK
IPCLKLNK StepMode Step Mode eNodeB DSP IPCLKLINK
IPCLKLNK VlanId VLAN ID eNodeB DSP IPCLKLINK
IPCLKLNK UtcOffset UTC Offset eNodeB None

ADD IPCLKLINK
IPCLKLNK PRI Priority eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK ANNFREQ Announce Freq eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK SYNCFREQ Sync Freq eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK MASTERPRIO Master Priority eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK PROFILETYPE Profile Type eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK NEGDURATION Negotiate Duration eNodeB
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK IPMODE IP mode eNodeB DSP IPCLKLINK
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK CIPV6 Client IPv6 eNodeB DSP IPCLKLINK
LST IPCLKLINK
ADD IPCLKLINK
IPCLKLNK SIPV6 Server IPv6 eNodeB
LST IPCLKLINK
ADD SYNCETH
DSP SYNCETH
SyncEth LN SyncEth Clock No. eNodeB MOD SYNCETH
RMV SYNCETH
LST SYNCETH
ADD SYNCETH
SyncEth CN Cabinet No. eNodeB
LST SYNCETH
ADD SYNCETH
SyncEth SRN Subrack No. eNodeB
LST SYNCETH
ADD SYNCETH
SyncEth SN Slot No. eNodeB
LST SYNCETH
ADD SYNCETH
SyncEth PN Port No. eNodeB
LST SYNCETH
ADD SYNCETH
MOD SYNCETH
SyncEth SSM SSM Selection eNodeB
DSP SYNCETH
LST SYNCETH
SyncEth ActiveState Link Active State eNodeB DSP SYNCETH
SyncEth AvailableState Link Available State eNodeB DSP SYNCETH
ADD SYNCETH
SyncEth PRI Priority eNodeB MOD SYNCETH
LST SYNCETH
Tasm AvailableState Clock Source State eNodeB DSP CLKSRC
Tasm LicenseAuthorized License Authorized eNodeB DSP CLKSRC

Clock Source
Tasm PRI eNodeB DSP CLKSRC
Priority
SET CLKMODE
Tasm SRCNO Clock Source No. eNodeB DSP CLKSRC
LST CLKMODE
Selected Clock SET CLKMODE
Tasm CLKSRC eNodeB
Source LST CLKMODE
SET CLKMODE
Clock Working
Tasm MODE eNodeB DSP CLKSTAT
Mode
LST CLKMODE
SET
Clock CLKSYNCMODE
Tasm CLKSYNCMODE Synchronization eNodeB DSP CLKSTAT
Mode LST
CLKSYNCMODE
Current Clock
Tasm CurrentSrcStatus eNodeB DSP CLKSTAT
Source State
DSP CLKRECORD
Tasm PllStatus PLL Status eNodeB DSP CLKSTAT
DSP CLKTST
Current Clock
Tasm CurrentSrc eNodeB DSP CLKSTAT
Source
DSP CLKDA
DSP CLKRECORD
DSP CLKSTAT
DSP CLKTHD
DSP CLKTST
DSP DARECORD
DSP TSTCLKOUT
Tasm CN Cabinet No. eNodeB LST
CLKDATARECORD
MOD CENTERDA
MOD CURRDA
SET CLKTHD
SET TSTCLKOUT
STP CLKTST
STR CLKTST
DSP CLKDA
DSP CLKRECORD
DSP CLKSTAT
DSP CLKTHD
DSP CLKTST
DSP DARECORD
DSP TSTCLKOUT
Tasm SRN Subrack No. eNodeB LST
CLKDATARECORD
MOD CENTERDA
MOD CURRDA
SET CLKTHD
SET TSTCLKOUT
STP CLKTST
STR CLKTST
DSP CLKDA
DSP CLKRECORD
DSP CLKSTAT
DSP CLKTHD
DSP CLKTST
DSP DARECORD
DSP TSTCLKOUT
Tasm SN Slot No. eNodeB LST
CLKDATARECORD
MOD CENTERDA
MOD CURRDA
SET CLKTHD
SET TSTCLKOUT
STP CLKTST
STR CLKTST
SET LOCALCLKQL
Tasm QL Quality Level eNodeB DSP SYNCETH
LST LOCALCLKQL
LST BBP
BBP CN Cabinet No. eNodeB
MOD BBP
LST BBP
BBP SRN Subrack No. eNodeB
MOD BBP
LST BBP
BBP SN Slot No. eNodeB
MOD BBP
BBP TYPE Board Type eNodeB None

ADD BRD
BBP WM Work Mode eNodeB MOD BBP
LST BBP
BBP AdmState Administrative state eNodeB None
Duration of the
BBP TIME eNodeB BLK BRD
shutting down state
BBP BLKTP Block Type eNodeB BLK BRD
BBP AlarmState Alarm Status eNodeB None
BBP OpState Operational State eNodeB None

BBP AvailabilityStatus Availability Status eNodeB None
BBP Elabel Electronic Label eNodeB None
BBP BoardType Type eNodeB None
BBP BoardSerial Serial Number eNodeB None
BBP BoardDesc Description eNodeB None

Date of
BBP BoardManu eNodeB None
Manufacture
BBP BoardVendor Vendor eNodeB None
BBP BoardIssue Issue Number eNodeB None
BBP RuType Board Type eNodeB None
BBP CpuDspUsage CPU/DSP Usage eNodeB None
BBP ObjectNumber Object Number eNodeB None
BBP ObjectType Object Type eNodeB None

BBP BoardTemperature Board Temperature eNodeB None
BBP HPATemperature HPA Temperature eNodeB None
BBP OperateResult Operate Result eNodeB None
BBP ServiceType Service Type eNodeB None
BBP DEVTYPE DEVTYPE eNodeB None
BBP NeName Office Name eNodeB None
BBP SoftVer Software Version eNodeB None
BBP HardVer Hardware Version eNodeB None
BBP BtrmVer BootRom Version eNodeB None
BBP HwTestTime Test Time eNodeB None
BBP TestResult Test Result eNodeB None

Downlink
BBP DLFREQ eNodeB None
Frequency
BBP ULFREQ Uplink Frequency eNodeB None
BbuFan CN Cabinet No. eNodeB DSP FAN
BbuFan SRN Subrack No. eNodeB DSP FAN
BbuFan SN Slot No. eNodeB DSP FAN
BbuFan Temperature Temperature eNodeB DSP FAN

BbuFan SpeedRate Fan Speed Rate eNodeB DSP FAN
BbuFan AlarmState Alarm Status eNodeB None
BbuFan OpState Operational State eNodeB None

BbuFan AvailabilityStatus Availability Status eNodeB None
BbuFan Elabel Electronic Label eNodeB None
BbuFan BoardType Type eNodeB None
BbuFan BoardSerial Serial Number eNodeB None
BbuFan BoardDesc Description eNodeB None

Date of
BbuFan BoardManu eNodeB None
Manufacture
BbuFan BoardVendor Vendor eNodeB None
BbuFan BoardIssue Issue Number eNodeB None
BbuFan RuType Board Type eNodeB None
BbuFan CpuDspUsage CPU/DSP Usage eNodeB None
BbuFan ObjectNumber Object Number eNodeB None
BbuFan ObjectType Object Type eNodeB None

BbuFan BoardTemperature Board Temperature eNodeB None
BbuFan HPATemperature HPA Temperature eNodeB None
BbuFan OperateResult Operate Result eNodeB None
BbuFan ServiceType Service Type eNodeB None
BbuFan DEVTYPE DEVTYPE eNodeB None
BbuFan NeName Office Name eNodeB None
BbuFan SoftVer Software Version eNodeB None
BbuFan HardVer Hardware Version eNodeB None
BbuFan BtrmVer BootRom Version eNodeB None
BbuFan HwTestTime Test Time eNodeB None
BbuFan TestResult Test Result eNodeB None

Downlink
BbuFan DLFREQ eNodeB None
Frequency
BbuFan ULFREQ Uplink Frequency eNodeB None
ADD CCU
CLR CCUALM
DSP CCU
CCU CN Cabinet No. eNodeB
LST CCU
MOD CCU
RMV CCU
ADD CCU
CLR CCUALM
DSP CCU
CCU SRN Subrack No. eNodeB
LST CCU
MOD CCU
RMV CCU
ADD CCU
CLR CCUALM
DSP CCU
CCU SN Slot No. eNodeB
LST CCU
MOD CCU
RMV CCU
ADD CCU
Manager Cabinet
CCU MCN eNodeB MOD CCU
No.
LST CCU
ADD CCU
Manager Subrack
CCU MSRN eNodeB MOD CCU
No.
LST CCU
ADD CCU
CCU MPN Manager Port No. eNodeB MOD CCU
LST CCU
ADD CCU
CCU DCF DirectConnectFlag eNodeB MOD CCU
LST CCU
ADD CCU
MOD CCU
CCU CCN Cascade No. eNodeB
DSP CCU
LST CCU
ADD CCU
Connected
CCU CS eNodeB MOD CCU
Standard
LST CCU
ADD CCU
Special Boolean
CCU SBAF eNodeB MOD CCU
Alarm Flag
LST CCU
CCU LPortStatus Left Port Status eNodeB DSP CCU
CCU RPortStatus Right Port Status eNodeB DSP CCU
CCU SoftwareVersion Software Version eNodeB DSP CCU
CCU PCBVersion PCB Version eNodeB DSP CCU
CCU EPLDVersion EPLD Version eNodeB DSP CCU
DSP CPRILBR
CPRILBR RCN RRU Chain No. eNodeB
STR CPRILBRNEG
Current head line
CPRILBR CURLBR eNodeB DSP CPRILBR
bit rate
Current head
CPRILBR CURNEGSTAT eNodeB DSP CPRILBR
negotiation status
Current tail line bit

CPRILBR CURTAILLBR eNodeB DSP CPRILBR
rate
Current tail
CPRILBR CURNEGSTAT eNodeB DSP CPRILBR
negotiation status
CPRILBR CN Cabinet No. eNodeB DSP CPRILBR
CPRILBR SRN Subrack No. eNodeB DSP CPRILBR
CPRILBR SN Slot No. eNodeB DSP CPRILBR
CPRILBR NODE Node eNodeB DSP CPRILBR

CPRILBR MAXBR Max bit rate eNodeB DSP CPRILBR
DSP CPRIPORT
DSP
CpriPort CN Cabinet No. eNodeB
RRUCHAINPHYTO
PO
DSP CPRIPORT
DSP
CpriPort SRN Subrack No. eNodeB
RRUCHAINPHYTO
PO
DSP CPRIPORT
DSP
CpriPort SN Slot No. eNodeB
RRUCHAINPHYTO
PO
DSP CPRIPORT
DSP
CpriPort OPTN Optical Port No. eNodeB
RRUCHAINPHYTO
PO
CpriPort CpriRate CPRI Bit Rate eNodeB DSP CPRIPORT
CpriPort AdmState Block Status eNodeB DSP CPRIPORT
CpriPort InstallStatus Install Status eNodeB DSP CPRIPORT

CpriPort CPRIPortMode CPRI Port Mode eNodeB DSP CPRIPORT
CpriPort PortType Port Type eNodeB DSP CPRIPORT
CpriPort BackupMode Backup Mode eNodeB None
CpriPort CMChannelType CM Channel Type eNodeB None
CpriPort DLBandWidth DL Band Width eNodeB None
CpriPort DLIQConsnum DL IQ Consnum eNodeB None

CpriPort ULIQConsnum UL IQ Consnum eNodeB None
CPRI Port Mux

CpriPort CpriMuxStatus eNodeB DSP CPRIPORT
Status
Energy
SET ECMP
ENERGYCON MP Consumption eNodeB
LST ECMP
Measurement Point
MPT CN Cabinet No. eNodeB None
MPT SRN Subrack No. eNodeB None
MPT SN Slot No. eNodeB None
MPT TYPE Board Type eNodeB None
MPT StandbyStatus StandBy Status eNodeB DSP BRD

MPT AlarmState Alarm Status eNodeB None
MPT OpState Operational State eNodeB None

MPT AvailabilityStatus Availability Status eNodeB None
MPT Elabel Electronic Label eNodeB None
MPT BoardType Type eNodeB None
MPT BoardSerial Serial Number eNodeB None
MPT BoardDesc Description eNodeB None

Date of
MPT BoardManu eNodeB None
Manufacture
MPT BoardVendor Vendor eNodeB None
MPT BoardIssue Issue Number eNodeB None
MPT RuType Board Type eNodeB None
MPT CpuDspUsage CPU/DSP Usage eNodeB None
MPT ObjectNumber Object Number eNodeB None
MPT ObjectType Object Type eNodeB None

MPT BoardTemperature Board Temperature eNodeB None
MPT HPATemperature HPA Temperature eNodeB None
MPT OperateResult Operate Result eNodeB None
MPT ServiceType Service Type eNodeB None
MPT DEVTYPE DEVTYPE eNodeB None
MPT NeName Office Name eNodeB None
MPT SoftVer Software Version eNodeB None
MPT HardVer Hardware Version eNodeB None
MPT BtrmVer BootRom Version eNodeB None
MPT HwTestTime Test Time eNodeB None
MPT TestResult Test Result eNodeB None

Downlink
MPT DLFREQ eNodeB None
Frequency
MPT ULFREQ Uplink Frequency eNodeB None
PEU CN Cabinet No. eNodeB DSP UPEU
PEU SRN Subrack No. eNodeB DSP UPEU
PEU SN Slot No. eNodeB DSP UPEU
PEU UpeuSparePower UPEU Spare Power eNodeB DSP UPEU
PEU BbuSparePower BBU Spare Power eNodeB DSP UPEU

PEU AlarmState Alarm Status eNodeB None
PEU OpState Operational State eNodeB None

PEU AvailabilityStatus Availability Status eNodeB None
PEU Elabel Electronic Label eNodeB None
PEU BoardType Type eNodeB None
PEU BoardSerial Serial Number eNodeB None
PEU BoardDesc Description eNodeB None

Date of
PEU BoardManu eNodeB None
Manufacture
PEU BoardVendor Vendor eNodeB None
PEU BoardIssue Issue Number eNodeB None
PEU RuType Board Type eNodeB None
PEU CpuDspUsage CPU/DSP Usage eNodeB None
PEU ObjectNumber Object Number eNodeB None
PEU ObjectType Object Type eNodeB None

PEU BoardTemperature Board Temperature eNodeB None
PEU HPATemperature HPA Temperature eNodeB None
PEU OperateResult Operate Result eNodeB None
PEU ServiceType Service Type eNodeB None
PEU DEVTYPE DEVTYPE eNodeB None
PEU NeName Office Name eNodeB None
PEU SoftVer Software Version eNodeB None
PEU HardVer Hardware Version eNodeB None
PEU BtrmVer BootRom Version eNodeB None
PEU HwTestTime Test Time eNodeB None
PEU TestResult Test Result eNodeB None

Downlink
PEU DLFREQ eNodeB None
Frequency
PEU ULFREQ Uplink Frequency eNodeB None
PSU Intelligent SET PSUISS

PSUIS PSUISS eNodeB
Shutdown Switch LST PSUISS
SFP CN Cabinet No. eNodeB DSP SFP
SFP SRN Subrack No. eNodeB DSP SFP
SFP SN Slot No. eNodeB DSP SFP

SFP Module
SFP MODULEID eNodeB DSP SFP
Number
SFP InstallStatus Installed status eNodeB DSP SFP

SFP OptType SFP Module Type eNodeB DSP SFP
SFP VendorName Manufacturer name eNodeB DSP SFP
SFP TransMode Transmission Mode eNodeB DSP SFP
SFP WaveLength Wavelength eNodeB DSP SFP
Transmission code
SFP Rating eNodeB DSP SFP
rate
Transmission
distance of single-
SFP LinkLength0 mode fiber (9- eNodeB DSP SFP
micrometer core
diameter)
Transmission
distance of single-
micrometer core
diameter)
Transmission
distance of multi-
micrometer core
diameter)
Transmission
distance of multi-
SFP LinkLength3 mode fiber (62.5- eNodeB DSP SFP
micrometer core
diameter)
SFP Temperature Temperature eNodeB DSP SFP
SFP Voltage Voltage eNodeB DSP SFP
SFP Current Current eNodeB DSP SFP
SFP OutputPower TX optical power eNodeB DSP SFP
SFP InputPower RX optical power eNodeB DSP SFP
Transmission
CopperCableLengt
SFP distance of copper eNodeB None
h
cable
DSP BRDRAT
LST UTRP
TRP CN Cabinet No. eNodeB
MOD UTRP
SET BRDRAT
DSP BRDRAT
LST UTRP
TRP SRN Subrack No. eNodeB
MOD UTRP
SET BRDRAT
DSP BRDRAT
LST UTRP
TRP SN Slot No. eNodeB
MOD UTRP
SET BRDRAT
MOD UTRP
TRP SUBTYPE SubBoard Type eNodeB
LST UTRP
Board Standby
TRP StandbyStatus eNodeB None
Status
TRP AlarmState Alarm Status eNodeB None
TRP OpState Operational State eNodeB None

TRP AvailabilityStatus Availability Status eNodeB None
TRP Elabel Electronic Label eNodeB None
TRP BoardType Type eNodeB None
TRP BoardSerial Serial Number eNodeB None
TRP BoardDesc Description eNodeB None

Date of
TRP BoardManu eNodeB None
Manufacture
TRP BoardVendor Vendor eNodeB None
TRP BoardIssue Issue Number eNodeB None
TRP RuType Board Type eNodeB None
TRP CpuDspUsage CPU/DSP Usage eNodeB None
TRP ObjectNumber Object Number eNodeB None
TRP ObjectType Object Type eNodeB None

TRP BoardTemperature Board Temperature eNodeB None
TRP HPATemperature HPA Temperature eNodeB None
TRP OperateResult Operate Result eNodeB None
TRP ServiceType Service Type eNodeB None
TRP DEVTYPE DEVTYPE eNodeB None
TRP NeName Office Name eNodeB None
TRP SoftVer Software Version eNodeB None
TRP HardVer Hardware Version eNodeB None
TRP BtrmVer BootRom Version eNodeB None
TRP HwTestTime Test Time eNodeB None
TRP TestResult Test Result eNodeB None

Downlink
TRP DLFREQ eNodeB None
Frequency
TRP ULFREQ Uplink Frequency eNodeB None
UCIU CN Cabinet No. eNodeB None
UCIU SRN Subrack No. eNodeB None
UCIU SN Slot No. eNodeB None

UCIU AlarmState Alarm Status eNodeB None
UCIU OpState Operational State eNodeB None

UCIU AvailabilityStatus Availability Status eNodeB None
UCIU Elabel Electronic Label eNodeB None
UCIU BoardType Type eNodeB None
UCIU BoardSerial Serial Number eNodeB None
UCIU BoardDesc Description eNodeB None

Date of
UCIU BoardManu eNodeB None
Manufacture
UCIU BoardVendor Vendor eNodeB None
UCIU BoardIssue Issue Number eNodeB None
UCIU RuType Board Type eNodeB None
UCIU CpuDspUsage CPU/DSP Usage eNodeB None
UCIU ObjectNumber Object Number eNodeB None
UCIU ObjectType Object Type eNodeB None

UCIU BoardTemperature Board Temperature eNodeB None
UCIU HPATemperature HPA Temperature eNodeB None
UCIU OperateResult Operate Result eNodeB None
UCIU ServiceType Service Type eNodeB None
UCIU DEVTYPE DEVTYPE eNodeB None
UCIU NeName Office Name eNodeB None
UCIU SoftVer Software Version eNodeB None
UCIU HardVer Hardware Version eNodeB None
UCIU BtrmVer BootRom Version eNodeB None
UCIU HwTestTime Test Time eNodeB None
UCIU TestResult Test Result eNodeB None

Downlink
UCIU DLFREQ eNodeB None
Frequency
UCIU ULFREQ Uplink Frequency eNodeB None
UEIU CN Cabinet No. eNodeB None
UEIU SRN Subrack No. eNodeB None
UEIU SN Slot No. eNodeB None

UEIU AlarmState Alarm Status eNodeB None
UEIU OpState Operational State eNodeB None

UEIU AvailabilityStatus Availability Status eNodeB None
UEIU Elabel Electronic Label eNodeB None
UEIU BoardType Type eNodeB None
UEIU BoardSerial Serial Number eNodeB None
UEIU BoardDesc Description eNodeB None

Date of
UEIU BoardManu eNodeB None
Manufacture
UEIU BoardVendor Vendor eNodeB None
UEIU BoardIssue Issue Number eNodeB None
UEIU RuType Board Type eNodeB None
UEIU CpuDspUsage CPU/DSP Usage eNodeB None
UEIU ObjectNumber Object Number eNodeB None
UEIU ObjectType Object Type eNodeB None

UEIU BoardTemperature Board Temperature eNodeB None
UEIU HPATemperature HPA Temperature eNodeB None
UEIU OperateResult Operate Result eNodeB None
UEIU ServiceType Service Type eNodeB None
UEIU DEVTYPE DEVTYPE eNodeB None
UEIU NeName Office Name eNodeB None
UEIU SoftVer Software Version eNodeB None
UEIU HardVer Hardware Version eNodeB None
UEIU BtrmVer BootRom Version eNodeB None
UEIU HwTestTime Test Time eNodeB None
UEIU TestResult Test Result eNodeB None

Downlink
UEIU DLFREQ eNodeB None
Frequency
UEIU ULFREQ Uplink Frequency eNodeB None
USCU CN Cabinet No. eNodeB None
USCU SRN Subrack No. eNodeB None
USCU SN Slot No. eNodeB None

USCU AlarmState Alarm Status eNodeB None
USCU OpState Operational State eNodeB None

USCU AvailabilityStatus Availability Status eNodeB None
USCU Elabel Electronic Label eNodeB None
USCU BoardType Type eNodeB None
USCU BoardSerial Serial Number eNodeB None
USCU BoardDesc Description eNodeB None

Date of
USCU BoardManu eNodeB None
Manufacture
USCU BoardVendor Vendor eNodeB None
USCU BoardIssue Issue Number eNodeB None
USCU RuType Board Type eNodeB None
USCU CpuDspUsage CPU/DSP Usage eNodeB None
USCU ObjectNumber Object Number eNodeB None
USCU ObjectType Object Type eNodeB None

USCU BoardTemperature Board Temperature eNodeB None
USCU HPATemperature HPA Temperature eNodeB None
USCU OperateResult Operate Result eNodeB None
USCU ServiceType Service Type eNodeB None
USCU DEVTYPE DEVTYPE eNodeB None
USCU NeName Office Name eNodeB None
USCU SoftVer Software Version eNodeB None
USCU HardVer Hardware Version eNodeB None
USCU BtrmVer BootRom Version eNodeB None
USCU HwTestTime Test Time eNodeB None
USCU TestResult Test Result eNodeB None

Downlink
USCU DLFREQ eNodeB None
Frequency
USCU ULFREQ Uplink Frequency eNodeB None
SET EQUIPMENT
Equipment DID Deployment ID eNodeB
LST EQUIPMENT
Battery Intelligent
SET EQUIPMENT
Equipment BATIMS Management eNodeB
LST EQUIPMENT
Switch
Power Lose
SET EQUIPMENT
Equipment PAE Redundancy Alarm eNodeB
LST EQUIPMENT
Enabled
SET MNTMODE
Equipment MNTMode Maintenance Mode eNodeB
LST MNTMODE
Start Time of Status SET MNTMODE

Equipment ST eNodeB
Setting LST MNTMODE
End Time of Status SET MNTMODE
Equipment ET eNodeB
Setting LST MNTMODE
Maintenance Mode SET MNTMODE

Equipment MMSetRemark eNodeB
Setting Remark LST MNTMODE
Current
Equipment CurrMNTMode eNodeB DSP MNTMODE
Maintenance Mode
Direct Voltage SET DVAS

Equipment DVAS eNodeB
Alarm Switch LST DVAS
Direct Voltage
SET DVAS
Equipment DVAH Alarm Occured eNodeB
LST DVAS
Threshold
Direct Voltage
SET DVAS
Equipment DVAL Alarm Restored eNodeB
LST DVAS
Threshold
ADD CABINET
DSP CABMFRINFO
Cabinet CN Cabinet No. eNodeB LST CABINET
MOD CABINET
RMV CABINET
ADD CABINET
Cabinet TYPE Cabinet Type eNodeB MOD CABINET
LST CABINET
ADD CABINET
Cabinet DESC Cabinet Description eNodeB MOD CABINET
LST CABINET
Cabinet CabinetType Model eNodeB DSP CABMFRINFO

ADD SUBRACK
LST SUBRACK
Subrack CN Cabinet No. eNodeB
MOD SUBRACK
RMV SUBRACK
ADD SUBRACK
LST SUBRACK
Subrack SRN Subrack No. eNodeB
MOD SUBRACK
RMV SUBRACK
ADD SUBRACK
Subrack TYPE Subrack Type eNodeB
LST SUBRACK
ADD SUBRACK
Subrack DESC Subrack Description eNodeB MOD SUBRACK
LST SUBRACK
Subrack PWRTYPE Power Type eNodeB None

RU AlarmState Alarm Status eNodeB DSP BRD
RU OpState Operational State eNodeB DSP BRD

RU AvailabilityStatus Availability Status eNodeB DSP BRD
RU Elabel Electronic Label eNodeB DSP ELABEL
DSP
RU BoardType Type eNodeB
BRDMFRINFO
DSP
BRDMFRINFO
RU BoardSerial Serial Number eNodeB DSP CABMFRINFO
DSP
HWTSTRESULT
DSP
BRDMFRINFO
RU BoardDesc Description eNodeB DSP CABMFRINFO
DSP
HWTSTRESULT
DSP
Date of
RU BoardManu eNodeB BRDMFRINFO
Manufacture
DSP CABMFRINFO
DSP
RU BoardVendor Vendor eNodeB BRDMFRINFO
DSP CABMFRINFO
DSP
RU BoardIssue Issue Number eNodeB
BRDMFRINFO
RU RuType Board Type eNodeB DSP BRD
RU CpuDspUsage CPU/DSP Usage eNodeB DSP CPUUSAGE
RU ObjectNumber Object Number eNodeB DSP CPUUSAGE
RU ObjectType Object Type eNodeB DSP CPUUSAGE

RU BoardTemperature Board Temperature eNodeB DSP BRDTEMP
RU HPATemperature HPA Temperature eNodeB DSP BRDTEMP
RU OperateResult Operate Result eNodeB None
RU ServiceType Service Type eNodeB None
RU DEVTYPE DEVTYPE eNodeB DSP ELABEL
DSP
RU NeName Office Name eNodeB
HWTSTRESULT
DSP
RU SoftVer Software Version eNodeB
HWTSTRESULT
DSP
RU HardVer Hardware Version eNodeB
HWTSTRESULT
DSP
RU BtrmVer BootRom Version eNodeB
HWTSTRESULT
DSP
RU HwTestTime Test Time eNodeB
HWTSTRESULT
DSP
RU TestResult Test Result eNodeB
HWTSTRESULT
Downlink
RU DLFREQ eNodeB STR HWTST
Frequency
RU ULFREQ Uplink Frequency eNodeB STR HWTST
ADD EMU
CLR EMUALM
DSP EMU
EMU CN Cabinet No. eNodeB
LST EMU
MOD EMU
RMV EMU
ADD EMU
CLR EMUALM
DSP EMU
EMU SRN Subrack No. eNodeB
LST EMU
MOD EMU
RMV EMU
ADD EMU
CLR EMUALM
DSP EMU
EMU SN Slot No. eNodeB
LST EMU
MOD EMU
RMV EMU
Manager Cabinet ADD EMU
EMU MCN eNodeB
No. LST EMU
Manager Subrack ADD EMU

EMU MSRN eNodeB
No. LST EMU
ADD EMU
EMU MPN Manager Port No. eNodeB MOD EMU
LST EMU
ADD EMU
EMU ADDR Address eNodeB MOD EMU
LST EMU
ADD EMU
Temperature Alarm
EMU TLTHD eNodeB MOD EMU
Lower Threshold
LST EMU
ADD EMU
Temperature Alarm
EMU TUTHD eNodeB MOD EMU
Upper Threshold
LST EMU
ADD EMU
Humidity Alarm
EMU HLTHD eNodeB MOD EMU
Lower Threshold
LST EMU
ADD EMU
Humidity Alarm
EMU HUTHD eNodeB MOD EMU
Upper Threshold
LST EMU
ADD EMU
Special Analog
EMU SAAF eNodeB MOD EMU
Alarm Flag
LST EMU
ADD EMU
Special Boolean
EMU SBAF eNodeB MOD EMU
Alarm Flag
LST EMU
Ambient
EMU Temperature eNodeB DSP EMU
Temperature
EMU Humidity Ambient Humidity eNodeB DSP EMU
EMU Invol48 -48V Input Voltage eNodeB DSP EMU

Analog Port 1
EMU Anain1 eNodeB DSP EMU
Measurement Value
Analog Port 2
Measurement Value
Analog Port 3
Measurement Value
Analog Port 4
Measurement Value
EMU AlarmState Alarm Status eNodeB None
EMU OpState Operational State eNodeB None

EMU AvailabilityStatus Availability Status eNodeB None
EMU Elabel Electronic Label eNodeB None
EMU BoardType Type eNodeB None
EMU BoardSerial Serial Number eNodeB None
EMU BoardDesc Description eNodeB None

Date of
EMU BoardManu eNodeB None
Manufacture
EMU BoardVendor Vendor eNodeB None
EMU BoardIssue Issue Number eNodeB None
EMU RuType Board Type eNodeB None
EMU CpuDspUsage CPU/DSP Usage eNodeB None
EMU ObjectNumber Object Number eNodeB None
EMU ObjectType Object Type eNodeB None

EMU BoardTemperature Board Temperature eNodeB None
EMU HPATemperature HPA Temperature eNodeB None
EMU OperateResult Operate Result eNodeB None
EMU ServiceType Service Type eNodeB None
EMU DEVTYPE DEVTYPE eNodeB None
EMU NeName Office Name eNodeB None
EMU SoftVer Software Version eNodeB None
EMU HardVer Hardware Version eNodeB None
EMU BtrmVer BootRom Version eNodeB None
EMU HwTestTime Test Time eNodeB None
EMU TestResult Test Result eNodeB None

Downlink
EMU DLFREQ eNodeB None
Frequency
EMU ULFREQ Uplink Frequency eNodeB None
ADD FMU
CLR FMUALM
DSP FMU
FMU CN Cabinet No. eNodeB
LST FMU
MOD FMU
RMV FMU
ADD FMU
CLR FMUALM
DSP FMU
FMU SRN Subrack No. eNodeB
LST FMU
MOD FMU
RMV FMU
ADD FMU
CLR FMUALM
DSP FMU
FMU SN Slot No. eNodeB
LST FMU
MOD FMU
RMV FMU
ADD FMU
Manager Cabinet
FMU MCN eNodeB MOD FMU
No.
LST FMU
ADD FMU
Manager Subrack
FMU MSRN eNodeB MOD FMU
No.
LST FMU
ADD FMU
FMU MPN Manager Port No. eNodeB MOD FMU
LST FMU
ADD FMU
FMU ADDR Address eNodeB MOD FMU
LST FMU
ADD FMU
Special Boolean
FMU SBAF eNodeB MOD FMU
Alarm Flag
LST FMU
FMU SpeedRate Fan Speed Rate eNodeB DSP FMU
Temperature at Fan
FMU TempOut eNodeB DSP FMU
Air Outlet
Temperature at Fan
FMU TempIn eNodeB DSP FMU
Air Inlet
FMU AverageSpeed Fan Average Speed eNodeB DSP FMU
ADD FMU
Smart Temperature
FMU STC eNodeB MOD FMU
Control
LST FMU
ADD FMU
Temperature
FMU TCMODE eNodeB MOD FMU
Control Mode
LST FMU
FMU AlarmState Alarm Status eNodeB None

FMU OpState Operational State eNodeB None
FMU AvailabilityStatus Availability Status eNodeB None
FMU Elabel Electronic Label eNodeB None

FMU BoardType Type eNodeB None
FMU BoardSerial Serial Number eNodeB None
FMU BoardDesc Description eNodeB None
Date of
FMU BoardManu eNodeB None
Manufacture
FMU BoardVendor Vendor eNodeB None
FMU BoardIssue Issue Number eNodeB None
FMU RuType Board Type eNodeB None
FMU CpuDspUsage CPU/DSP Usage eNodeB None

FMU ObjectNumber Object Number eNodeB None
FMU ObjectType Object Type eNodeB None
FMU BoardTemperature Board Temperature eNodeB None
FMU HPATemperature HPA Temperature eNodeB None
FMU OperateResult Operate Result eNodeB None
FMU ServiceType Service Type eNodeB None
FMU DEVTYPE DEVTYPE eNodeB None
FMU NeName Office Name eNodeB None
FMU SoftVer Software Version eNodeB None
FMU HardVer Hardware Version eNodeB None
FMU BtrmVer BootRom Version eNodeB None
FMU HwTestTime Test Time eNodeB None
FMU TestResult Test Result eNodeB None

Downlink
FMU DLFREQ eNodeB None
Frequency
FMU ULFREQ Uplink Frequency eNodeB None
ADD TCU
CLR TCUALM
DSP TCU
TCU CN Cabinet No. eNodeB
LST TCU
MOD TCU
RMV TCU
ADD TCU
CLR TCUALM
DSP TCU
TCU SRN Subrack No. eNodeB
LST TCU
MOD TCU
RMV TCU
ADD TCU
CLR TCUALM
DSP TCU
TCU SN Slot No. eNodeB
LST TCU
MOD TCU
RMV TCU
Manager Cabinet ADD TCU

TCU MCN eNodeB
No. LST TCU
Manager Subrack ADD TCU

TCU MSRN eNodeB
No. LST TCU
ADD TCU
TCU MPN Manager Port No. eNodeB MOD TCU
LST TCU
ADD TCU
TCU ADDR Address eNodeB MOD TCU
LST TCU
ADD TCU
Temperature Alarm
TCU TLTHD eNodeB MOD TCU
Lower Threshold
LST TCU
ADD TCU
Temperature Alarm
TCU TUTHD eNodeB MOD TCU
Upper Threshold
LST TCU
ADD TCU
Special Boolean
TCU SBAF eNodeB MOD TCU
Alarm Flag
LST TCU
TCU DeviceType Device Type eNodeB DSP TCU
TCU TempIn Temperature In eNodeB DSP TCU
TCU TempOut Temperature Out eNodeB DSP TCU
TCU TempInner Temperature Inner eNodeB DSP TCU
Inner Cycle Fan

TCU InCycleSpeedRate eNodeB DSP TCU
Average Speed
OutCycleSpeedRat Outer Cycle Fan

TCU eNodeB DSP TCU
e Average Speed
TCU Power Power eNodeB DSP TCU
TCU SoftwareVersion Software Version eNodeB DSP TCU
TCU PCBVersion PCB Version eNodeB DSP TCU

TCU EPLDVersion EPLD Version eNodeB DSP TCU
TCU SoftwareBuildTime Software Build Time eNodeB DSP TCU
TCU VersionDescription Version Description eNodeB DSP TCU
TCU ProduceDate Produce Date eNodeB None
TCU Manufacturer Manufacturer eNodeB DSP TCU

TCU AlarmState Alarm Status eNodeB None
TCU OpState Operational State eNodeB None

TCU AvailabilityStatus Availability Status eNodeB None
TCU Elabel Electronic Label eNodeB None
TCU BoardType Type eNodeB None
TCU BoardSerial Serial Number eNodeB None
TCU BoardDesc Description eNodeB None

Date of
TCU BoardManu eNodeB None
Manufacture
TCU BoardVendor Vendor eNodeB None
TCU BoardIssue Issue Number eNodeB None
TCU RuType Board Type eNodeB None
TCU CpuDspUsage CPU/DSP Usage eNodeB None
TCU ObjectNumber Object Number eNodeB None
TCU ObjectType Object Type eNodeB None

TCU BoardTemperature Board Temperature eNodeB None
TCU HPATemperature HPA Temperature eNodeB None
TCU OperateResult Operate Result eNodeB None
TCU ServiceType Service Type eNodeB None
TCU DEVTYPE DEVTYPE eNodeB None
TCU NeName Office Name eNodeB None
TCU SoftVer Software Version eNodeB None
TCU HardVer Hardware Version eNodeB None
TCU BtrmVer BootRom Version eNodeB None
TCU HwTestTime Test Time eNodeB None
TCU TestResult Test Result eNodeB None

Downlink
TCU DLFREQ eNodeB None
Frequency
TCU ULFREQ Uplink Frequency eNodeB None
LST HTCDPA
HtCDPa CN Cabinet No. eNodeB
MOD HTCDPA
LST HTCDPA
HtCDPa SRN Subrack No. eNodeB
MOD HTCDPA
LST HTCDPA
HtCDPa SN Slot No. eNodeB
MOD HTCDPA
Low Temperature MOD HTCDPA

HtCDPa LTCP eNodeB
Critical Point LST HTCDPA
High Temperature MOD HTCDPA

HtCDPa HTCP eNodeB
Critical Point LST HTCDPA
Temperature Limit MOD HTCDPA
HtCDPa TLT eNodeB
at Air Outlet LST HTCDPA
MOD HTCDPA
HtCDPa DBD Dead Band eNodeB
LST HTCDPA
Normal
MOD HTCDPA
HtCDPa NTDI Temperature Delta eNodeB
LST HTCDPA
Tin
Normal
MOD HTCDPA
HtCDPa NTDO Temperature Delta eNodeB
LST HTCDPA
Tout
High Temperature MOD HTCDPA

HtCDPa HTDO eNodeB
Delta Tout LST HTCDPA
ADD PMU
CLR PMUALM
DSP PMU
PMU CN Cabinet No. eNodeB
LST PMU
MOD PMU
RMV PMU
ADD PMU
CLR PMUALM
DSP PMU
PMU SRN Subrack No. eNodeB
LST PMU
MOD PMU
RMV PMU
ADD PMU
CLR PMUALM
DSP PMU
PMU SN Slot No. eNodeB
LST PMU
MOD PMU
RMV PMU
Manager Cabinet ADD PMU

PMU MCN eNodeB
No. LST PMU
Manager Subrack ADD PMU
PMU MSRN eNodeB
No. LST PMU
ADD PMU
PMU MPN Manager Port No. eNodeB MOD PMU
LST PMU
ADD PMU
PMU ADDR Address eNodeB MOD PMU
LST PMU
ADD PMU
PMU PTYPE Power System Type eNodeB MOD PMU
LST PMU
ADD PMU
AC Voltage Alarm
PMU ACVLTHD eNodeB MOD PMU
Lower Threshold
LST PMU
ADD PMU
AC Voltage Alarm
PMU ACVUTHD eNodeB MOD PMU
Upper Threshold
LST PMU
ADD PMU
DC Voltage Alarm
PMU DCVLTHD eNodeB MOD PMU
Lower Threshold
LST PMU
ADD PMU
DC Voltage Alarm
PMU DCVUTHD eNodeB MOD PMU
Upper Threshold
LST PMU
ADD PMU
Load Shutdown
PMU LSDF eNodeB MOD PMU
Flag
LST PMU
ADD PMU
Load Shutdown
PMU LSDV eNodeB MOD PMU
Voltage
LST PMU
Cabinet ADD PMU

PMU ATLTHD Temperature Alarm eNodeB MOD PMU
Lower Threshold LST PMU
Cabinet ADD PMU

PMU ATUTHD Temperature Alarm eNodeB MOD PMU
Upper Threshold LST PMU
Cabinet Humidity ADD PMU
PMU AHLTHD Alarm Lower eNodeB MOD PMU
Threshold LST PMU
Cabinet Humidity ADD PMU

PMU AHUTHD Alarm Upper eNodeB MOD PMU
Threshold LST PMU
ADD PMU
Special Analog
PMU SAAF eNodeB MOD PMU
Alarm Flag
LST PMU
ADD PMU
Special Boolean
PMU SBAF eNodeB MOD PMU
Alarm Flag
LST PMU
PMU AcVol AC Voltage eNodeB DSP PMU
PMU DcVol Busbar Voltage eNodeB DSP PMU
PMU LoadCurrent Load Total Current eNodeB DSP PMU
PMU LoadTemp Temperature eNodeB DSP PMU
PMU Humidity Cabinet Humidity eNodeB DSP PMU
Secondary Load
PMU ScdLoadPwrState eNodeB DSP PMU
Power State
Charging/Dischargi
PMU BatChargeState eNodeB DSP BATTERY
ng State
PMU BatCurrent Battery Current eNodeB DSP BATTERY
BatCurrentLimitStat Current Limiting

PMU eNodeB None
e State
PMU BatPowerState Battery Power State eNodeB DSP BATTERY

PMU BatRemainCapacity Remaining Capacity eNodeB DSP BATTERY
Battery
PMU BatTemp eNodeB DSP BATTERY
Temperature
PMU BatTestPhase Battery Test Phase eNodeB DSP BATTERY
PhotovoltaicArrayC Photovoltaic Array

PMU eNodeB DSP PMU
urrent Total Current
Diesel Generator
PMU DieselCurrent eNodeB DSP PMU
Current
Auxiliary Battery
AuxBatCabinetTem
PMU Cabinet eNodeB DSP PMU
p
Temperature
PMU SoftwareVersion Software Version eNodeB DSP PMU
PMU PCBVersion PCB Version eNodeB DSP PMU
PMU EPLDVersion EPLD Version eNodeB DSP PMU
PMU SoftwareBuildTime Software Build Time eNodeB DSP PMU
PMU VersionDescription Version Description eNodeB DSP PMU
PMU ProduceDate Produce Date eNodeB DSP PMU

PMU Manufacturer Manufacturer eNodeB DSP PMU
PSU Intelligent
PMU ISCapability Shutdown eNodeB DSP PMU
Capability
PSU Intelligent
PMU ISSwitchState eNodeB DSP PMU
Shutdown Switch
PMU ISExecuteResult Execute Result eNodeB None
PMU BatRemainTime Remaining Time eNodeB DSP BATTERY
Battery
BatAccumulatedCh
PMU Accumulated eNodeB DSP BATTERY
argeTime
Charge Time
Battery
BatAccumulatedSle
PMU Accumulated eNodeB DSP BATTERY
epingTime
Sleeping Time
Battery Intelligent
PMU BatImsCapability Management eNodeB DSP PMU
Capability
Battery Intelligent
PMU BatImsSwitchState eNodeB DSP PMU
Management Mode
PMU AlarmState Alarm Status eNodeB None
PMU OpState Operational State eNodeB None

PMU AvailabilityStatus Availability Status eNodeB None
PMU Elabel Electronic Label eNodeB None
PMU BoardType Type eNodeB None
PMU BoardSerial Serial Number eNodeB None
PMU BoardDesc Description eNodeB None

Date of
PMU BoardManu eNodeB None
Manufacture
PMU BoardVendor Vendor eNodeB None
PMU BoardIssue Issue Number eNodeB None
PMU RuType Board Type eNodeB None
PMU CpuDspUsage CPU/DSP Usage eNodeB None
PMU ObjectNumber Object Number eNodeB None
PMU ObjectType Object Type eNodeB None

PMU BoardTemperature Board Temperature eNodeB None
PMU HPATemperature HPA Temperature eNodeB None
PMU OperateResult Operate Result eNodeB None
PMU ServiceType Service Type eNodeB None
PMU DEVTYPE DEVTYPE eNodeB None
PMU NeName Office Name eNodeB None
PMU SoftVer Software Version eNodeB None
PMU HardVer Hardware Version eNodeB None
PMU BtrmVer BootRom Version eNodeB None
PMU HwTestTime Test Time eNodeB None
PMU TestResult Test Result eNodeB None

Downlink
PMU DLFREQ eNodeB None
Frequency
PMU ULFREQ Uplink Frequency eNodeB None
ADD DIESELGEN
DSP DIESELGEN
LST DIESELGEN
MOD DIESELGEN
DieselGen CN Cabinet No. eNodeB RMV DIESELGEN
STP
DIESELGENTST
STR
DIESELGENTST
ADD DIESELGEN
DSP DIESELGEN
LST DIESELGEN
MOD DIESELGEN
DieselGen SRN Subrack No. eNodeB RMV DIESELGEN
STP
DIESELGENTST
STR
DIESELGENTST
ADD DIESELGEN
DSP DIESELGEN
LST DIESELGEN
MOD DIESELGEN
DieselGen SN Slot No. eNodeB RMV DIESELGEN
STP
DIESELGENTST
STR
DIESELGENTST
ADD DIESELGEN
Intelligent Control
DieselGen ICF eNodeB MOD DIESELGEN
Flag
LST DIESELGEN
ADD DIESELGEN
DieselGen POWER Rated Power eNodeB MOD DIESELGEN
LST DIESELGEN
DieselGen OL Oil Level eNodeB DSP DIESELGEN
Diesel Generator
DieselGen DGC eNodeB DSP DIESELGEN
Current
DieselGen TRT Total Running Time eNodeB DSP DIESELGEN
ADD BATTERY
DSP BATINDT
DSP BATTERY
Battery CN Cabinet No. eNodeB LST BATTERY
MOD BATINDT
MOD BATTERY
RMV BATTERY
ADD BATTERY
DSP BATINDT
DSP BATTERY
Battery SRN Subrack No. eNodeB LST BATTERY
MOD BATINDT
MOD BATTERY
RMV BATTERY
ADD BATTERY
DSP BATINDT
DSP BATTERY
Battery SN Slot No. eNodeB LST BATTERY
MOD BATINDT
MOD BATTERY
RMV BATTERY
ADD BATTERY
Battery INSTALLTYPE Installation Type eNodeB MOD BATTERY
LST BATTERY
ADD BATTERY
Boost-Charging
Battery BCD eNodeB MOD BATTERY
Duration
LST BATTERY
ADD BATTERY
Boost-Charging
Battery BCV eNodeB MOD BATTERY
Voltage
LST BATTERY
ADD BATTERY
Battery BC1 Battery 1 Capacity eNodeB MOD BATTERY
LST BATTERY
ADD BATTERY
Battery Current
Battery BCLC eNodeB MOD BATTERY
Limiting Coefficient
LST BATTERY
ADD BATTERY
Float-Charging
Battery FCV eNodeB MOD BATTERY
Voltage
LST BATTERY
ADD BATTERY
High Temperature
Battery HTSDF eNodeB MOD BATTERY
Shutdown Flag
LST BATTERY
ADD BATTERY
Shutdown
Battery SDT eNodeB MOD BATTERY
Temperature
LST BATTERY
ADD BATTERY
Low Voltage
Battery LVSDF eNodeB MOD BATTERY
Shutdown Flag
LST BATTERY
ADD BATTERY
Battery SDV Shutdown Voltage eNodeB MOD BATTERY
LST BATTERY
Temperature ADD BATTERY

Battery TCC Compensation eNodeB MOD BATTERY
Coefficient LST BATTERY
ADD BATTERY
Temperature Alarm
Battery TLTHD eNodeB MOD BATTERY
Lower Threshold
LST BATTERY
ADD BATTERY
Temperature Alarm
Battery TUTHD eNodeB MOD BATTERY
Upper Threshold
LST BATTERY
ADD BATTERY
MOD BATTERY
Battery BN Battery Number eNodeB
DSP BATTERY
LST BATTERY
ADD BATTERY
MOD BATTERY
Battery BTYPE Battery Type eNodeB
DSP BATTERY
LST BATTERY
Battery PCT Power Cut Times eNodeB DSP BATTERY
Charge Times In
Battery CTHALF eNodeB DSP BATTERY
Half an Hour
Charge Times In 1
Battery CT1H eNodeB DSP BATTERY
Hour
Charge Times In 2
Hours
Charge Times In 3
Hours
Charge Times In 4
Hours
Charge Times In 5
Hours
Charge Times In 6
Hours
Charge Times In 7
Hours
Charge Times In 8
Hours
Charge Times In
Battery CT8UH eNodeB DSP BATTERY
More than 8 Hours
Discharge Times In
Battery DCTHALF eNodeB DSP BATTERY
Half an Hour
Discharge Times In
Battery DCT1 eNodeB DSP BATTERY
1 Hour
Discharge Times In
2 Hours
Discharge Times In
3 Hours
Discharge Times In
4 Hours
Discharge Times In
5 Hours
Discharge Times In
6 Hours
Discharge Times In
7 Hours
Discharge Times In
8 Hours
Discharge Times In
Battery DCTU8 eNodeB DSP BATTERY
More than 8 Hours
MOD BATINDT
Battery DATE Installation Date eNodeB
DSP BATINDT
ADD BATTERY
Battery BC2 Battery 2 Capacity eNodeB MOD BATTERY
LST BATTERY
DSP BATTR
LST BATCTPA
BatCTPa CN Cabinet No. eNodeB MOD BATCTPA
STP BATTST
STR BATTST
DSP BATTR
LST BATCTPA
BatCTPa SRN Subrack No. eNodeB MOD BATCTPA
STP BATTST
STR BATTST
DSP BATTR
LST BATCTPA
BatCTPa SN Slot No. eNodeB MOD BATCTPA
STP BATTST
STR BATTST
0.05C10 Discharge MOD BATCTPA
BatCTPa DSCHGT0 eNodeB
Time LST BATCTPA

Time LST BATCTPA
Time LST BATCTPA

Time LST BATCTPA
Time LST BATCTPA

Time LST BATCTPA
Time LST BATCTPA

Time LST BATCTPA
Time LST BATCTPA

Time LST BATCTPA
Battery Charge MOD BATCTPA
BatCTPa EFF eNodeB
Efficiency LST BATCTPA
Discharge Test End MOD BATCTPA

BatCTPa ENDV eNodeB
Voltage LST BATCTPA
MOD BATCTPA
BatCTPa BATNUM Battery Number eNodeB
LST BATCTPA
Discharge Test MOD BATCTPA

BatCTPa DSTML eNodeB
Time Limit LST BATCTPA
Simple Discharge MOD BATCTPA

BatCTPa SDSTML eNodeB
Test Time Limit LST BATCTPA
Simple Discharge MOD BATCTPA

BatCTPa SDSEV eNodeB
Test End Voltage LST BATCTPA
Automatic Test MOD BATCTPA
BatCTPa ATMODE eNodeB
Mode LST BATCTPA
Timing Discharge MOD BATCTPA

BatCTPa TDSTM eNodeB
Test Time LST BATCTPA
Delayed Discharge MOD BATCTPA
BatCTPa DDSTM eNodeB
Test Time LST BATCTPA
STR BATTST
BatCTPa TYPE Battery Test Type eNodeB
DSP BATTR
BatCTPa TstStrDateTime Test Start Time eNodeB DSP BATTR
BatCTPa TstEndReason Test End Cause eNodeB DSP BATTR

BatCTPa TstResult Test Result eNodeB DSP BATTR
BatCTPa TstEffi Battery Efficency eNodeB DSP BATTR
Discharge Last
BatCTPa TstDischrLstTime eNodeB DSP BATTR
Time
Discharge End
BatCTPa TstDischrEndVol eNodeB DSP BATTR
Voltage
Discharge Average
BatCTPa TstDischrCurr eNodeB DSP BATTR
Current
BatCTPa TstDischrAh Discharge AH eNodeB DSP BATTR
Battery
BatCTPa TstBatTemp eNodeB DSP BATTR
Temperature
ADD PSU
DSP PSU
PSU CN Cabinet No. eNodeB
LST PSU
RMV PSU
ADD PSU
DSP PSU
PSU SRN Subrack No. eNodeB
LST PSU
RMV PSU
ADD PSU
DSP PSU
PSU SN Slot No. eNodeB
LST PSU
RMV PSU
PSU RunningStatus Running Status eNodeB DSP PSU
PSU ProduceDate Produce Date eNodeB DSP PSU

PSU Manufacturer Manufacturer eNodeB DSP PSU
PSU PCBVersion PCB Version eNodeB DSP PSU
PSU EPLDVersion EPLD Version eNodeB DSP PSU
PSU SoftwareBuildTime Software Build Time eNodeB DSP PSU

PSU AlarmState Alarm Status eNodeB None
PSU OpState Operational State eNodeB None

PSU AvailabilityStatus Availability Status eNodeB None
PSU Elabel Electronic Label eNodeB None
PSU BoardType Type eNodeB None
PSU BoardSerial Serial Number eNodeB None
PSU BoardDesc Description eNodeB None

Date of
PSU BoardManu eNodeB None
Manufacture
PSU BoardVendor Vendor eNodeB None
PSU BoardIssue Issue Number eNodeB None
PSU RuType Board Type eNodeB None
PSU CpuDspUsage CPU/DSP Usage eNodeB None
PSU ObjectNumber Object Number eNodeB None
PSU ObjectType Object Type eNodeB None

PSU BoardTemperature Board Temperature eNodeB None
PSU HPATemperature HPA Temperature eNodeB None
PSU OperateResult Operate Result eNodeB None
PSU ServiceType Service Type eNodeB None
PSU DEVTYPE DEVTYPE eNodeB None
PSU NeName Office Name eNodeB None
PSU SoftVer Software Version eNodeB DSP PSU
PSU HardVer Hardware Version eNodeB None
PSU BtrmVer BootRom Version eNodeB None
PSU HwTestTime Test Time eNodeB None
PSU TestResult Test Result eNodeB None

Downlink
PSU DLFREQ eNodeB None
Frequency
PSU ULFREQ Uplink Frequency eNodeB None
LST OUTPORT
OutPort CN Cabinet No. eNodeB
SET OUTPORT
LST OUTPORT
OutPort SRN Subrack No. eNodeB
SET OUTPORT
LST OUTPORT
OutPort SN Slot No. eNodeB
SET OUTPORT
LST OUTPORT
OutPort PN Port No. eNodeB
SET OUTPORT
SET OUTPORT
OutPort NAME Port Name eNodeB
LST OUTPORT
SET OUTPORT
OutPort SW Port Switch eNodeB
LST OUTPORT
LST ALMPORT
AlmPort CN Cabinet No. eNodeB
SET ALMPORT
LST ALMPORT
AlmPort SRN Subrack No. eNodeB
SET ALMPORT
LST ALMPORT
AlmPort SN Slot No. eNodeB
SET ALMPORT
LST ALMPORT
AlmPort PN Port No. eNodeB
SET ALMPORT
SET ALMPORT
AlmPort SW Switch eNodeB
LST ALMPORT
LST ALMPORT
AlmPort AID Alarm ID eNodeB
SET ALMPORT
SET ALMPORT
AlmPort PT Port Type eNodeB
LST ALMPORT
SET ALMPORT
AlmPort AVOL Alarm Voltage eNodeB
LST ALMPORT
SET ALMPORT
AlmPort UL Alarm Upper Limit eNodeB
LST ALMPORT
SET ALMPORT
AlmPort LL Alarm Lower Limit eNodeB
LST ALMPORT
SET ALMPORT
AlmPort ST Sensor Type eNodeB
LST ALMPORT
Sensor
SET ALMPORT
AlmPort SMUL Measurement eNodeB
LST ALMPORT
Upper Limit
Sensor
SET ALMPORT
AlmPort SMLL Measurement eNodeB
LST ALMPORT
Lower Limit
Sensor Output SET ALMPORT

AlmPort SOUL eNodeB
Upper Limit LST ALMPORT
Sensor Output SET ALMPORT
AlmPort SOLL eNodeB
Lower Limit LST ALMPORT
SET CONNTYPE
SSL CONNTYPE Connection Type eNodeB
LST SSLCONF
SET
Authentication
SSL AUTHMODE eNodeB SSLAUTHMODE
Mode
LST SSLCONF
AAU CN Cabinet No. eNodeB None

AAU SRN Subrack No. eNodeB None
AAU SN Slot No. eNodeB None
AAU RN RRU Name eNodeB None
AAU RT RRU Type eNodeB None
AAU AdmState Administrative state eNodeB None
AAU AlarmState Alarm Status eNodeB None
AAU OpState Operational State eNodeB None

AAU AvailabilityStatus Availability Status eNodeB None
AAU Elabel Electronic Label eNodeB None
AAU BoardType Type eNodeB None
AAU BoardSerial Serial Number eNodeB None
AAU BoardDesc Description eNodeB None

Date of
AAU BoardManu eNodeB None
Manufacture
AAU BoardVendor Vendor eNodeB None
AAU BoardIssue Issue Number eNodeB None
AAU RuType Board Type eNodeB None
AAU CpuDspUsage CPU/DSP Usage eNodeB None
AAU ObjectNumber Object Number eNodeB None
AAU ObjectType Object Type eNodeB None

AAU BoardTemperature Board Temperature eNodeB None
AAU HPATemperature HPA Temperature eNodeB None
AAU OperateResult Operate Result eNodeB None
AAU ServiceType Service Type eNodeB None
AAU DEVTYPE DEVTYPE eNodeB None

VSWR alarm post-
AAU ALMPROCSW eNodeB None
processing switch
VSWR alarm post-

ALMPROCTHRHL
AAU processing eNodeB None
D
threshold
VSWR alarm
AAU ALMTHRHLD eNodeB None
threshold
AAU PS RRU Position eNodeB None
AAU RCN RRU Chain No. eNodeB None
AAU TP RRU Topo Position eNodeB None

RRU Work
AAU RS eNodeB None
Standard
Number of RX
AAU RXNUM eNodeB None
channels
Number of TX
AAU TXNUM eNodeB None
channels
CarrierNumPerRxBr Number of carriers

AAU eNodeB None
anch on the RX channel
CarrierNumPerTxBr Number of carriers

AAU eNodeB None
anch on the TX channel
Minimum UL
AAU RxMinFreq eNodeB None
frequency
Maximum UL
AAU RxMaxFreq eNodeB None
frequency
Minimum DL
AAU TxMinFreq eNodeB None
frequency
Maximum DL
AAU TxMaxFreq eNodeB None
frequency
Maximum output
MaxOutPwrPerBran
AAU power on the TX eNodeB None
ch
channel
AAU UlBranchGain UL channel gain eNodeB None
Supported UL
AAU UlBandwidth eNodeB None
Bandwidth
AAU PATemperature PA Temperature eNodeB None
AAU Temperature Board Temperature eNodeB None
AAU Level Trunk Level eNodeB None
Physical RRU
AAU DeviceSerialNo eNodeB None
device serial No.
RRU standard
AAU RatType eNodeB None
capability
AAU AccessDirection Access Direction eNodeB None
Maximum Output
AAU MaxOutputOneCar Power of TX Unit 0 eNodeB None
(Single Carrier)
Maximum Output
AAU MaxOutputMutiCar Power of TX Unit 0 eNodeB None
(Multiple Carriers)
Supported DL
AAU DlBandwidth eNodeB None
Bandwidth
AAU PHYID Physical ID. eNodeB None
Periodical Report
AAU SW eNodeB None
Switch
AAU TM Test Time eNodeB None
AAU CM Check Mode eNodeB None
Power Statistic
AAU PSP eNodeB None
Period
Power Statistic
AAU PST eNodeB None
Time
AAU ULFREQ UL Freq eNodeB None
AAU BER Bit Error Rate eNodeB None

AAU InftDetectResult Result eNodeB None
AAU SETTYPE Set Type eNodeB None
AAU THRESHOLD Threshold eNodeB None
AAU CPRI Bit Rate CPRI Line Rate eNodeB None
AAU NeName Office Name eNodeB None
AAU SoftVer Software Version eNodeB None
AAU HardVer Hardware Version eNodeB None
AAU BtrmVer BootRom Version eNodeB None
AAU HwTestTime Test Time eNodeB None
AAU TestResult Test Result eNodeB None

Downlink
AAU DLFREQ eNodeB None
Frequency
AAU ULFREQ Uplink Frequency eNodeB None
RE AdmState Administrative state eNodeB LST RRU

ADD RRU
VSWR alarm post-
RE ALMPROCSW eNodeB MOD RRU
processing switch
LST RRU
VSWR alarm post- ADD RRU

ALMPROCTHRHL
RE processing eNodeB MOD RRU
D
threshold LST RRU
ADD RRU
VSWR alarm
RE ALMTHRHLD eNodeB MOD RRU
threshold
LST RRU
ADD RRU
RE PS RRU Position eNodeB
LST RRU
ADD RRU
RE RCN RRU Chain No. eNodeB
LST RRU
ADD RRU
DSP
RE TP RRU Topo Position eNodeB RRUCHAINPHYTO
PO
LST RRU
ADD RRU
RRU Work
RE RS eNodeB MOD RRU
Standard
LST RRU
ADD RRU
Number of RX MOD RRU
RE RXNUM eNodeB
channels DSP RRU
LST RRU
ADD RRU
Number of TX MOD RRU
RE TXNUM eNodeB
channels DSP RRU
LST RRU

RE eNodeB DSP RRU

RE eNodeB DSP RRU
Minimum UL
RE RxMinFreq eNodeB None
frequency
Maximum UL
RE RxMaxFreq eNodeB None
frequency
Minimum DL
RE TxMinFreq eNodeB None
frequency
Maximum DL
RE TxMaxFreq eNodeB None
frequency
Maximum output
MaxOutPwrPerBran
RE power on the TX eNodeB DSP RRU
ch
channel
RE UlBranchGain UL channel gain eNodeB DSP RRU
Supported UL
RE UlBandwidth eNodeB None
Bandwidth
RE PATemperature PA Temperature eNodeB None
RE Temperature Board Temperature eNodeB None
DSP
RE Level Trunk Level eNodeB RRUCHAINPHYTO
PO
DSP
Physical RRU
RE DeviceSerialNo eNodeB RRUCHAINPHYTO
device serial No.
PO
DSP
RRU standard
RE RatType eNodeB RRUCHAINPHYTO
capability
PO
RE AccessDirection Access Direction eNodeB DSP RRU
Maximum Output
RE MaxOutputOneCar Power of TX Unit 0 eNodeB None
(Single Carrier)
Maximum Output
RE MaxOutputMutiCar Power of TX Unit 0 eNodeB None
(Multiple Carriers)
Supported DL
RE DlBandwidth eNodeB None
Bandwidth
RE PHYID Physical ID. eNodeB None
Periodical Report
RE SW eNodeB STR RRULNKTST
Switch
RE TM Test Time eNodeB STR RRULNKTST
RE CM Check Mode eNodeB None
Power Statistic
RE PSP eNodeB None
Period
Power Statistic
RE PST eNodeB None
Time
RE ULFREQ UL Freq eNodeB None
RE BER Bit Error Rate eNodeB STR RRULNKTST

RE InftDetectResult Result eNodeB None
SET
RE SETTYPE Set Type eNodeB
CPRITHRESHOLD
SET
CPRITHRESHOLD
RE THRESHOLD Threshold eNodeB
DSP
CPRITHRESHOLD
DSP
RE CPRI Bit Rate CPRI Line Rate eNodeB
CPRITHRESHOLD
RE AlarmState Alarm Status eNodeB None
RE OpState Operational State eNodeB None

RE AvailabilityStatus Availability Status eNodeB None
RE Elabel Electronic Label eNodeB None
RE BoardType Type eNodeB None
RE BoardSerial Serial Number eNodeB None
RE BoardDesc Description eNodeB None

Date of
RE BoardManu eNodeB None
Manufacture
RE BoardVendor Vendor eNodeB None
RE BoardIssue Issue Number eNodeB None
RE RuType Board Type eNodeB None
RE CpuDspUsage CPU/DSP Usage eNodeB None
RE ObjectNumber Object Number eNodeB None
RE ObjectType Object Type eNodeB None

RE BoardTemperature Board Temperature eNodeB None
RE HPATemperature HPA Temperature eNodeB None
RE OperateResult Operate Result eNodeB None
RE ServiceType Service Type eNodeB None
RE DEVTYPE DEVTYPE eNodeB None
RE NeName Office Name eNodeB None
RE SoftVer Software Version eNodeB None
RE HardVer Hardware Version eNodeB None
RE BtrmVer BootRom Version eNodeB None
RE HwTestTime Test Time eNodeB None
RE TestResult Test Result eNodeB None

Downlink
RE DLFREQ eNodeB None
Frequency
RE ULFREQ Uplink Frequency eNodeB None
RFU CN Cabinet No. eNodeB None
RFU SRN Subrack No. eNodeB None
RFU SN Slot No. eNodeB None
RFU RT RRU type eNodeB None

RFU AdmState Administrative state eNodeB None
RFU AlarmState Alarm Status eNodeB None
RFU OpState Operational State eNodeB None

RFU AvailabilityStatus Availability Status eNodeB None
RFU Elabel Electronic Label eNodeB None
RFU BoardType Type eNodeB None
RFU BoardSerial Serial Number eNodeB None
RFU BoardDesc Description eNodeB None

Date of
RFU BoardManu eNodeB None
Manufacture
RFU BoardVendor Vendor eNodeB None
RFU BoardIssue Issue Number eNodeB None
RFU RuType Board Type eNodeB None
RFU CpuDspUsage CPU/DSP Usage eNodeB None
RFU ObjectNumber Object Number eNodeB None
RFU ObjectType Object Type eNodeB None

RFU BoardTemperature Board Temperature eNodeB None
RFU HPATemperature HPA Temperature eNodeB None
RFU OperateResult Operate Result eNodeB None
RFU ServiceType Service Type eNodeB None
RFU DEVTYPE DEVTYPE eNodeB None

VSWR alarm post-
RFU ALMPROCSW eNodeB None
processing switch
VSWR alarm post-

ALMPROCTHRHL
RFU processing eNodeB None
D
threshold
VSWR alarm
RFU ALMTHRHLD eNodeB None
threshold
RFU PS RRU Position eNodeB None
RFU RCN RRU Chain No. eNodeB None
RFU TP RRU Topo Position eNodeB None

RRU Work
RFU RS eNodeB None
Standard
Number of RX
RFU RXNUM eNodeB None
channels
Number of TX
RFU TXNUM eNodeB None
channels

RFU eNodeB None

RFU eNodeB None
Minimum UL
RFU RxMinFreq eNodeB None
frequency
Maximum UL
RFU RxMaxFreq eNodeB None
frequency
Minimum DL
RFU TxMinFreq eNodeB None
frequency
Maximum DL
RFU TxMaxFreq eNodeB None
frequency
Maximum output
MaxOutPwrPerBran
RFU power on the TX eNodeB None
ch
channel
RFU UlBranchGain UL channel gain eNodeB None
Supported UL
RFU UlBandwidth eNodeB None
Bandwidth
RFU PATemperature PA Temperature eNodeB None
RFU Temperature Board Temperature eNodeB None
RFU Level Trunk Level eNodeB None
Physical RRU
RFU DeviceSerialNo eNodeB None
device serial No.
RRU standard
RFU RatType eNodeB None
capability
RFU AccessDirection Access Direction eNodeB None
Maximum Output
RFU MaxOutputOneCar Power of TX Unit 0 eNodeB None
(Single Carrier)
Maximum Output
RFU MaxOutputMutiCar Power of TX Unit 0 eNodeB None
(Multiple Carriers)
Supported DL
RFU DlBandwidth eNodeB None
Bandwidth
RFU PHYID Physical ID. eNodeB None
Periodical Report
RFU SW eNodeB None
Switch
RFU TM Test Time eNodeB None
RFU CM Check Mode eNodeB None
Power Statistic
RFU PSP eNodeB None
Period
Power Statistic
RFU PST eNodeB None
Time
RFU ULFREQ UL Freq eNodeB None
RFU BER Bit Error Rate eNodeB None

RFU InftDetectResult Result eNodeB None
RFU SETTYPE Set Type eNodeB None
RFU THRESHOLD Threshold eNodeB None
RFU CPRI Bit Rate CPRI Line Rate eNodeB None
RFU NeName Office Name eNodeB None
RFU SoftVer Software Version eNodeB None
RFU HardVer Hardware Version eNodeB None
RFU BtrmVer BootRom Version eNodeB None
RFU HwTestTime Test Time eNodeB None
RFU TestResult Test Result eNodeB None

Downlink
RFU DLFREQ eNodeB None
Frequency
RFU ULFREQ Uplink Frequency eNodeB None
RRU CN Cabinet No. eNodeB None
RRU SRN Subrack No. eNodeB None
RRU SN Slot No. eNodeB None
ADD RRU
RRU RN RRU Name eNodeB MOD RRU
LST RRU
RRU RT RRU type eNodeB LST RRU
RRU TSTTYPE Test Type eNodeB None
RRU TSTTIME Test Time eNodeB None
DELTATHRESHOL
RRU Delta Threshold eNodeB None
D
RRU Ant No. Antenna Port No. eNodeB None
RRU Test Result Test Result eNodeB None
RRU RTWP Value RTWP Value eNodeB None
RRU RTWP Delta Value RTWP Delta Value eNodeB None
RRU RTWP Max Value RTWP Max Value eNodeB None
RRU AdmState Administrative state eNodeB None

RRU AlarmState Alarm Status eNodeB None
RRU OpState Operational State eNodeB None

RRU AvailabilityStatus Availability Status eNodeB None
RRU Elabel Electronic Label eNodeB None
RRU BoardType Type eNodeB None
RRU BoardSerial Serial Number eNodeB None
RRU BoardDesc Description eNodeB None

Date of
RRU BoardManu eNodeB None
Manufacture
RRU BoardVendor Vendor eNodeB None
RRU BoardIssue Issue Number eNodeB None
RRU RuType Board Type eNodeB None
RRU CpuDspUsage CPU/DSP Usage eNodeB None
RRU ObjectNumber Object Number eNodeB None
RRU ObjectType Object Type eNodeB None

RRU BoardTemperature Board Temperature eNodeB None
RRU HPATemperature HPA Temperature eNodeB None
RRU OperateResult Operate Result eNodeB None
RRU ServiceType Service Type eNodeB None
RRU DEVTYPE DEVTYPE eNodeB None

VSWR alarm post-
RRU ALMPROCSW eNodeB None
processing switch
VSWR alarm post-

ALMPROCTHRHL
RRU processing eNodeB None
D
threshold
VSWR alarm
RRU ALMTHRHLD eNodeB None
threshold
RRU PS RRU Position eNodeB None
RRU RCN RRU Chain No. eNodeB None
RRU TP RRU Topo Position eNodeB None

RRU Work
RRU RS eNodeB None
Standard
Number of RX
RRU RXNUM eNodeB None
channels
Number of TX
RRU TXNUM eNodeB None
channels

RRU eNodeB None

RRU eNodeB None
Minimum UL
RRU RxMinFreq eNodeB None
frequency
Maximum UL
RRU RxMaxFreq eNodeB None
frequency
Minimum DL
RRU TxMinFreq eNodeB None
frequency
Maximum DL
RRU TxMaxFreq eNodeB None
frequency
Maximum output
MaxOutPwrPerBran
RRU power on the TX eNodeB None
ch
channel
RRU UlBranchGain UL channel gain eNodeB None
Supported UL
RRU UlBandwidth eNodeB None
Bandwidth
RRU PATemperature PA Temperature eNodeB None
RRU Temperature Board Temperature eNodeB None
RRU Level Trunk Level eNodeB None
Physical RRU
RRU DeviceSerialNo eNodeB None
device serial No.
RRU standard
RRU RatType eNodeB None
capability
RRU AccessDirection Access Direction eNodeB None
Maximum Output
RRU MaxOutputOneCar Power of TX Unit 0 eNodeB None
(Single Carrier)
Maximum Output
RRU MaxOutputMutiCar Power of TX Unit 0 eNodeB None
(Multiple Carriers)
Supported DL
RRU DlBandwidth eNodeB None
Bandwidth
RRU PHYID Physical ID. eNodeB None
Periodical Report
RRU SW eNodeB None
Switch
RRU TM Test Time eNodeB None
RRU CM Check Mode eNodeB None
Power Statistic
RRU PSP eNodeB None
Period
Power Statistic
RRU PST eNodeB None
Time
RRU ULFREQ UL Freq eNodeB None
RRU BER Bit Error Rate eNodeB None

RRU InftDetectResult Result eNodeB None
RRU SETTYPE Set Type eNodeB None
RRU THRESHOLD Threshold eNodeB None
RRU CPRI Bit Rate CPRI Line Rate eNodeB None
RRU NeName Office Name eNodeB None
RRU SoftVer Software Version eNodeB None
RRU HardVer Hardware Version eNodeB None
RRU BtrmVer BootRom Version eNodeB None
RRU HwTestTime Test Time eNodeB None
RRU TestResult Test Result eNodeB None

Downlink
RRU DLFREQ eNodeB None
Frequency
RRU ULFREQ Uplink Frequency eNodeB None
ADD RRUCHAIN
DSP RRUCHAIN
RRUCHAIN RCN RRU Chain No. eNodeB LST RRUCHAIN
MOD RRUCHAIN
RMV RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN TT Topo Type eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
RRUCHAIN BM Backup Mode eNodeB MOD RRUCHAIN
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN HCN Head Cabinet No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN HSRN Head Subrack No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN HSN Head Slot No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN HPN Head Port No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN TCN Tail Cabinet No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN TSRN Tail Subrack No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN TSN Tail Slot No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
ADD RRUCHAIN
MOD RRUCHAIN
DSP
RRUCHAIN TPN Tail Port No. eNodeB
RRUCHAINPHYTO
PO
LST RRUCHAIN
BreakPoint MOD RRUCHAIN
RRUCHAIN BRKPOS1 eNodeB
Position1 LST RRUCHAIN
BreakPoint MOD RRUCHAIN
RRUCHAIN BRKPOS2 eNodeB
Position2 LST RRUCHAIN
ADD RRUCHAIN
RRUCHAIN AT Access Type eNodeB MOD RRUCHAIN
LST RRUCHAIN
ADD RRUCHAIN
RRUCHAIN CR CPRI Line Rate eNodeB MOD RRUCHAIN
LST RRUCHAIN
RRUCHAIN ChainLevel Chain Level eNodeB DSP RRUCHAIN
RRUCHAIN RRUNum RRU Number eNodeB DSP RRUCHAIN
DSP RXBRANCH
RxBranch CN Cabinet No. eNodeB LST RXBRANCH
MOD RXBRANCH
DSP RXBRANCH
RxBranch SRN Subrack No. eNodeB LST RXBRANCH
MOD RXBRANCH
DSP RXBRANCH
RxBranch SN Slot No. eNodeB LST RXBRANCH
MOD RXBRANCH
DSP RXBRANCH
RxBranch RXNO RX Channel No. eNodeB LST RXBRANCH
MOD RXBRANCH
MOD RXBRANCH
Logical Switch of
RxBranch RXSW eNodeB DSP RXBRANCH
RX Channel
LST RXBRANCH
MOD RXBRANCH
RxBranch ATTEN Attenuation eNodeB DSP RXBRANCH
LST RXBRANCH
Physical Switch of
RxBranch PhyStatus eNodeB DSP RXBRANCH
RX Channel
Band 1 Minimum
RxBranch RxMinFreq1 eNodeB DSP RXBRANCH
frequency
Band 1 Maximum
RxBranch RxMaxFreq1 eNodeB DSP RXBRANCH
frequency
Band 1 UL
RxBranch UlBandwidth1 eNodeB DSP RXBRANCH
Bandwidth
Band 2 Minimum
RxBranch RxMinFreq2 eNodeB DSP RXBRANCH
frequency
Band 2 Maximum
RxBranch RxMaxFreq2 eNodeB DSP RXBRANCH
frequency
Band 2 UL
RxBranch UlBandwidth2 eNodeB DSP RXBRANCH
Bandwidth
DSP TXBRANCH
DSP VSWR
LOC RRUTC
LST TXBRANCH
TxBranch CN Cabinet No. eNodeB MOD TXBRANCH
STR VSWRTEST
VER TXPOWER
STR
CROSFEEDTST
DSP TXBRANCH
DSP VSWR
LOC RRUTC
LST TXBRANCH
TxBranch SRN Subrack No. eNodeB MOD TXBRANCH
STR VSWRTEST
VER TXPOWER
STR
CROSFEEDTST
DSP TXBRANCH
DSP VSWR
LOC RRUTC
LST TXBRANCH
TxBranch SN Slot No. eNodeB MOD TXBRANCH
STR VSWRTEST
VER TXPOWER
STR
CROSFEEDTST
DSP TXBRANCH
DSP VSWR
LOC RRUTC
LST TXBRANCH
TxBranch TXNO TX Channel No. eNodeB MOD TXBRANCH
STR VSWRTEST
VER TXPOWER
STR
CROSFEEDTST
MOD TXBRANCH
Logical Switch of
TxBranch TXSW eNodeB DSP TXBRANCH
TX Channel
LST TXBRANCH
DSP TXBRANCH
TxBranch Vswr VSWR eNodeB DSP VSWR
STR VSWRTEST
Physical Switch of
TxBranch PhyStatus eNodeB DSP TXBRANCH
TX Channel
TxBranch TRVAL Turn OutPut Power eNodeB VER TXPOWER
Txbranch
TxBranch TFREQ eNodeB STR VSWRTEST
Frequency
Txbranch Power
TxBranch TPRV eNodeB STR VSWRTEST
Relative Value
TxBranch TESTTIME Test Time eNodeB STR VSWRTEST
TxBranch SiteNo Site No. eNodeB STR VSWRTEST
STR
TxBranch SectNo Sector No. eNodeB CROSFEEDTST
STR VSWRTEST
TxBranch SiteName Office Name eNodeB STR VSWRTEST
Maximum Output
Power Support
TxBranch TXMAXPWR eNodeB LOC RRUTC
Setting of the TX
Channel
Maximum Output
TXMAXPWRFORD
TxBranch Power of the TX eNodeB DSP TXBRANCH
SP
Channel
Maximum Output
TxBranch MaxOutputOneCar Power of TX Unit eNodeB DSP TXBRANCH
(Single Carrier)
Maximum Output
TxBranch MaxOutputMutiCar Power of TX Unit eNodeB DSP TXBRANCH
(Multiple Carriers)
Hardware Maximum
TxBranch TXHWMAXPWR Output Power of the eNodeB DSP TXBRANCH
TX Channel
Band 1 Minimum
TxBranch TxMinFreq1 eNodeB DSP TXBRANCH
frequency
Band 1 Maximum
TxBranch TxMaxFreq1 eNodeB DSP TXBRANCH
frequency
Band 1 DL
TxBranch DlBandwidth1 eNodeB DSP TXBRANCH
Bandwidth
Band 2 Minimum
TxBranch TxMinFreq2 eNodeB DSP TXBRANCH
frequency
Band 2 Maximum
TxBranch TxMaxFreq2 eNodeB DSP TXBRANCH
frequency
Band 2 DL
TxBranch DlBandwidth2 eNodeB DSP TXBRANCH
Bandwidth
Start Test STR

TxBranch STFREQ eNodeB
Frequency CROSFEEDTST
STR
TxBranch ETFREQ End Test Frequency eNodeB
CROSFEEDTST
STR
TxBranch CrossTestResult RESULT eNodeB
CROSFEEDTST
ADD NTPC
MOD NTPC
IPv4 Address of
NtpCp IP eNodeB RMV NTPC
NTP Server
SET
MASTERNTPS
ADD NTPC
Synchronization
NtpCp SYNCCYCLE eNodeB MOD NTPC
Period
LST NTPC
ADD NTPC
NtpCp PORT Port Number eNodeB MOD NTPC
LST NTPC
ADD NTPC
MOD NTPC
NtpCp MODE IP Mode eNodeB RMV NTPC
SET
MASTERNTPS
ADD NTPC
MOD NTPC
IPv6 Address of
NtpCp IPV6 eNodeB RMV NTPC
NTP Server
SET
MASTERNTPS
ADD NTPC
Authentication
NtpCp AUTHMODE eNodeB MOD NTPC
Mode
LST NTPC
ADD NTPC
NtpCp KEY Authentication Key eNodeB MOD NTPC
LST NTPC
ADD NTPC
Authentication Key
NtpCp KEYID eNodeB MOD NTPC
Index
LST NTPC
NtpCp MASTERFLAG Master Flag eNodeB LST NTPC

SET TZ
TZ ZONET Time Zone eNodeB
LST TZ
TZ DST Dst Tag Information eNodeB SET TZ

TZ SM Dst Start Mode eNodeB SET TZ
TZ SMONTH Dst Start Month eNodeB SET TZ
TZ SDAY Dst Start Day eNodeB SET TZ

Dst Start Week
TZ SWSEQ eNodeB SET TZ
Sequence
TZ SWEEK Dst Start Weekday eNodeB SET TZ
TZ ST Dst Start Time eNodeB SET TZ
TZ EM Dst End Mode eNodeB SET TZ
TZ EMONTH Dst End Month eNodeB SET TZ

TZ EDAY Dst End Day eNodeB SET TZ
Dst End Week

TZ EWSEQ eNodeB SET TZ
Sequence
TZ EWEEK Dst End Weekday eNodeB SET TZ
TZ ET Dst End Time eNodeB SET TZ
TZ TO DST Offset eNodeB SET TZ

TZ TIMEDIFF Time Difference eNodeB SET TZ
OmuCurTime DATE Date eNodeB SET TIME
OmuCurTime TIME Time eNodeB SET TIME
OmuCurTime DATETIME Time eNodeB DSP TIME
SET TIMESRC
DSP TIMESRC
LST
TimeSrc TIMESRC Time Source eNodeB
LATESTSUCCDAT
E
LST TIMESRC
Latest Successful LST

TimeSrc DATETIME Synchronization eNodeB LATESTSUCCDAT
Time E
Transport SET FTPSCLT
FTPCLT ENCRYMODE eNodeB
Encrypted Mode LST FTPSCLT
Support State SET FTPSCLT
FTPCLT SPTSTATEFWL eNodeB
Firewall LST FTPSCLT
Support SSL
SET FTPSCLT
FTPCLT SSLCERTAUTH Certificate eNodeB
LST FTPSCLT
Authentication
ADD
FTPSCLTDPORT
MOD
FTP Server IP FTPSCLTDPORT
FTPCLTPORT SERVERIP eNodeB
Address RMV
FTPSCLTDPORT
LST
FTPSCLTDPORT
ADD
FTPSCLTDPORT
MOD
FTPCLTPORT PORT Destination Port eNodeB
FTPSCLTDPORT
LST
FTPSCLTDPORT
ADD
CNOPERATOREXT
ENDEDQCI
LST
CNOPERATOREXT
ENDEDQCI
CnOperatorExtendedCnOperatorId CN Operator ID eNodeB
MOD
CNOPERATOREXT
ENDEDQCI
RMV
CNOPERATOREXT
ENDEDQCI
ADD
CNOPERATOREXT
ENDEDQCI
LST
CNOPERATOREXT
CN Operator ENDEDQCI
CnOperatorExtendedExtendedQci eNodeB
extended QCI MOD
CNOPERATOREXT
ENDEDQCI
RMV
CNOPERATOREXT
ENDEDQCI
ADD
CNOPERATOREXT
ENDEDQCI
Service-based inter- MOD
ServiceIrHoCfgGro
CnOperatorExtended RAT handover eNodeB CNOPERATOREXT
upId
policy group ID ENDEDQCI
LST
CNOPERATOREXT
ENDEDQCI
ADD
CNOPERATOREXT
ENDEDQCI
Service-based inter- MOD
ServiceIfHoCfgGrou
CnOperatorExtended Freq handover eNodeB CNOPERATOREXT
pId
policy group ID ENDEDQCI
LST
CNOPERATOREXT
ENDEDQCI
LST
CNOPERATORSTA
NDARDQCI
CnOperatorStandardCnOperatorId CN Operator ID eNodeB
MOD
CNOPERATORSTA
NDARDQCI
LST
CNOPERATORSTA
QoS Class NDARDQCI
CnOperatorStandardQci eNodeB
Indication MOD
CNOPERATORSTA
NDARDQCI
MOD
CNOPERATORSTA
Service-based inter-
ServiceIrHoCfgGro NDARDQCI
CnOperatorStandard RAT handover eNodeB
upId LST
policy group ID
CNOPERATORSTA
NDARDQCI
MOD
CNOPERATORSTA
ServiceIfHoCfgGrou NDARDQCI
CnOperatorStandard Freq handover eNodeB
pId LST
policy group ID
CNOPERATORSTA
NDARDQCI
LST
CSFALLBACKBLIN
DHOCFG
CSFallBackBlindHoCCnOperatorId CN Operator ID eNodeB
MOD
CSFALLBACKBLIN
DHOCFG
MOD
CSFALLBACKBLIN
Highest priority DHOCFG
CSFallBackBlindHoCInterRatHighestPri eNodeB
InterRat LST
CSFALLBACKBLIN
DHOCFG
MOD
CSFALLBACKBLIN
Second priority DHOCFG
CSFallBackBlindHoCInterRatSecondPri eNodeB
InterRat LST
CSFALLBACKBLIN
DHOCFG
MOD
CSFALLBACKBLIN
Lowest priority DHOCFG
CSFallBackBlindHoCInterRatLowestPri eNodeB
InterRat LST
CSFALLBACKBLIN
DHOCFG
MOD
CSFALLBACKBLIN
UTRAN LCS DHOCFG
CSFallBackBlindHoCUtranLcsCap eNodeB
capability LST
CSFALLBACKBLIN
DHOCFG
MOD
CSFALLBACKBLIN
GERAN LCS DHOCFG
CSFallBackBlindHoCGeranLcsCap eNodeB
capability LST
CSFALLBACKBLIN
DHOCFG
MOD
CSFALLBACKBLIN
CDMA2000 LCS DHOCFG
CSFallBackBlindHoCCdmaLcsCap eNodeB
capability LST
CSFALLBACKBLIN
DHOCFG
INTERPLMNHOLIS
T
LST
InterPlmnHoList CnOperatorId CN Operator ID eNodeB INTERPLMNHOLIS
T
RMV
INTERPLMNHOLIS
ADD
INTERPLMNHOLIS
T
LST
Target Mobile
InterPlmnHoList TarMcc eNodeB INTERPLMNHOLIS
country code
T
RMV
INTERPLMNHOLIS
T
ADD
INTERPLMNHOLIS
T
LST
Target Mobile
InterPlmnHoList TarMnc eNodeB INTERPLMNHOLIS
network code
T
RMV
INTERPLMNHOLIS
T
ADD
RATFREQPRIORIT
YGROUP
LST
RATFREQPRIORIT
RatFreqPriorityGrou RAT frequency YGROUP
RatFreqPriorityGrou eNodeB
pId priority group ID MOD
RATFREQPRIORIT
YGROUP
RMV
RATFREQPRIORIT
YGROUP
ADD
RATFREQPRIORIT
YGROUP
LST
RATFREQPRIORIT
YGROUP
RatFreqPriorityGrou RatType RAT Type eNodeB
MOD
RATFREQPRIORIT
YGROUP
RMV
RATFREQPRIORIT
YGROUP
ADD
RATFREQPRIORIT
YGROUP
LST
RATFREQPRIORIT
YGROUP
RatFreqPriorityGrou DlEarfcn Downlink EARFCN eNodeB
MOD
RATFREQPRIORIT
YGROUP
RMV
RATFREQPRIORIT
YGROUP
ADD
RATFREQPRIORIT
YGROUP
MOD
RatFreqPriorityGrou Priority Priority eNodeB RATFREQPRIORIT
YGROUP
LST
RATFREQPRIORIT
YGROUP
ADD
RATFREQPRIORIT
YGROUP
MOD
GERAN Frequency
RatFreqPriorityGrou BandIndicator eNodeB RATFREQPRIORIT
Indicator
YGROUP
LST
RATFREQPRIORIT
YGROUP
ADD
SERVICEIFHOCFG
GROUP
LST
SERVICEIFHOCFG
GROUP
ServiceIfHoCfgGrou CnOperatorId CN Operator ID eNodeB
MOD
SERVICEIFHOCFG
GROUP
RMV
SERVICEIFHOCFG
GROUP
ADD
SERVICEIFHOCFG
GROUP
LST
SERVICEIFHOCFG
ServiceIfHoCfgGrou GROUP
ServiceIfHoCfgGrou Freq handover eNodeB
pId MOD
policy group ID
SERVICEIFHOCFG
GROUP
RMV
SERVICEIFHOCFG
GROUP
ADD
SERVICEIFHOCFG
GROUP
MOD
Inter-Freq handover
ServiceIfHoCfgGrou InterFreqHoState eNodeB SERVICEIFHOCFG
state
GROUP
LST
SERVICEIFHOCFG
GROUP
ADD
SERVICEIFHOCFG
GROUP
MOD
ServiceIfHoCfgGrou DlEarfcn Downlink EARFCN eNodeB SERVICEIFHOCFG
GROUP
LST
SERVICEIFHOCFG
GROUP
ADD
SERVICEIRHOCF
GGROUP
LST
SERVICEIRHOCF
GGROUP
ServiceIrHoCfgGrou CnOperatorId CN Operator ID eNodeB
MOD
SERVICEIRHOCF
GGROUP
RMV
SERVICEIRHOCF
GGROUP
ADD
SERVICEIRHOCF
GGROUP
LST
SERVICEIRHOCF
ServiceIrHoCfgGro GGROUP
ServiceIrHoCfgGrou RAT handover eNodeB
upId MOD
policy group ID
SERVICEIRHOCF
GGROUP
RMV
SERVICEIRHOCF
GGROUP
ADD
SERVICEIRHOCF
GGROUP
MOD
Inter-RAT handover
ServiceIrHoCfgGrou InterRatHoState eNodeB SERVICEIRHOCF
state
GGROUP
LST
SERVICEIRHOCF
GGROUP
ADD SPIDCFG
LST SPIDCFG
SpidCfg Spid Spid eNodeB
MOD SPIDCFG
RMV SPIDCFG
ADD SPIDCFG
SpidCfg DrxStatus Drx status eNodeB MOD SPIDCFG
LST SPIDCFG
ADD SPIDCFG
RAT frequency
SpidCfg RatFreqPriorityInd eNodeB MOD SPIDCFG
priority indication
LST SPIDCFG
ADD SPIDCFG
RatFreqPriorityGrou RAT frequency
SpidCfg eNodeB MOD SPIDCFG
pId priority group ID
LST SPIDCFG
ADD SPIDCFG
SpidCfg PreallocationStatus PreallocationStatus eNodeB MOD SPIDCFG
LST SPIDCFG
ADD SPIDCFG
InterFreq Mlb
SpidCfg InterFreqMlbSwitch eNodeB MOD SPIDCFG
Switch
LST SPIDCFG
ADD SPIDCFG
SpidCfg InterRatMlbSwitch InterRat Mlb Switch eNodeB MOD SPIDCFG
LST SPIDCFG
SPID-based ADD SPIDCFG

HoBackToHPLMNS
SpidCfg Handover Back To eNodeB MOD SPIDCFG
witch
HPLMN Switch LST SPIDCFG
MOD
COUNTERCHECK
PARA
CounterCheckPara CounterCheckTimer Counter check timer eNodeB
LST
COUNTERCHECK
PARA
MOD
COUNTERCHECK
CounterCheckCoun Counter check PARA
CounterCheckPara eNodeB
tNum count number LST
COUNTERCHECK
PARA
MOD
COUNTERCHECK
CounterCheckUser Counter check user PARA
CounterCheckPara eNodeB
RelSwitch Release switch LST
COUNTERCHECK
PARA
MOD
ENODEBCIPHERC
Primary cipher AP
ENodeBCipherCap PrimaryCipherAlgo eNodeB
algorithm LST
ENODEBCIPHERC
AP
MOD
ENODEBCIPHERC
Second cipher AP
ENodeBCipherCap SecondCipherAlgo eNodeB
algorithm LST
ENODEBCIPHERC
AP
MOD
ENODEBCIPHERC
Third cipher AP
ENodeBCipherCap ThirdCipherAlgo eNodeB
algorithm LST
ENODEBCIPHERC
AP
MOD
ENODEBCONNSTA
S1MessageWaiting S1 Message TETIMER
ENodeBConnStateTi eNodeB
Timer Waiting Timer LST
ENODEBCONNSTA
TETIMER
MOD
ENODEBCONNSTA
X2MessageWaiting X2 Message TETIMER
ENODEBCONNSTA
TETIMER
MOD
ENODEBCONNSTA
UuMessageWaiting UU Message TETIMER
ENODEBCONNSTA
TETIMER
MOD
ENODEBINTEGRIT
PrimaryIntegrityAlg Primary integrity YCAP
ENodeBIntegrityCap eNodeB
o algorithm LST
ENODEBINTEGRIT
YCAP
MOD
ENODEBINTEGRIT
SecondIntegrityAlg Second integrity YCAP
ENodeBIntegrityCap eNodeB
o algorithm LST
ENODEBINTEGRIT
YCAP
MOD
ENODEBINTEGRIT
Third integrity YCAP
ENodeBIntegrityCap ThirdIntegrityAlgo eNodeB
algorithm LST
ENODEBINTEGRIT
YCAP
MOD
GLOBALPROCSWI
The Switch of X2 TCH
GlobalProcSwitch X2SonSetupSwitch eNodeB
setup by SON LST
GLOBALPROCSWI
TCH
MOD
GLOBALPROCSWI
X2SonLinkSetupTy The method of X2 TCH
GlobalProcSwitch eNodeB
pe setup by SON LST
GLOBALPROCSWI
TCH
MOD
GLOBALPROCSWI
TCH
GlobalProcSwitch SriAdaptiveSwitch SRI adaptive switch eNodeB
LST
GLOBALPROCSWI
TCH
MOD
GLOBALPROCSWI
TCH
GlobalProcSwitch LcgProfile LCG Profile eNodeB
LST
GLOBALPROCSWI
TCH
MOD
GLOBALPROCSWI
RncPoolHoRimSwit RNC POOL HO TCH
GlobalProcSwitch eNodeB
ch RIM Switch LST
GLOBALPROCSWI
TCH
MOD
GLOBALPROCSWI
UU Message
UuMsgSimulSendS TCH
GlobalProcSwitch Simultaneous eNodeB
witch LST
Sending Switch
GLOBALPROCSWI
TCH
MOD
GLOBALPROCSWI
Update eNB
X2BasedUptENode TCH
GlobalProcSwitch Configuration Via eNodeB
BCfgSwitch LST
X2 Switch
GLOBALPROCSWI
TCH
MOD
PDCPROHCPARA
PdcpRohcPara RohcSwitch ROHC switch eNodeB
LST
PDCPROHCPARA
MOD
ROHC Highest PDCPROHCPARA
PdcpRohcPara HighestMode eNodeB
mode LST
PDCPROHCPARA
MOD
Compression PDCPROHCPARA
PdcpRohcPara Profiles eNodeB
profiles LST
PDCPROHCPARA
MOD
RRCCONNSTATET
IMER
RrcConnStateTimer T302 Timer302 eNodeB
LST
RRCCONNSTATET
IMER
MOD
RRCCONNSTATET
T320ForLoadBalan Timer320 for load IMER
RrcConnStateTimer eNodeB
ce balance LST
RRCCONNSTATET
IMER
MOD
RRCCONNSTATET
Timer304 for IMER
RrcConnStateTimer T304ForEutran eNodeB
EUTRAN LST
RRCCONNSTATET
IMER
MOD
RRCCONNSTATET
Timer304 for IMER
RrcConnStateTimer T304ForGeran eNodeB
GERAN LST
RRCCONNSTATET
IMER
MOD
RRCCONNSTATET
IMER
RrcConnStateTimer T320ForOther Timer320 for other eNodeB
LST
RRCCONNSTATET
IMER
MOD
RRCCONNSTATET
IMER
RrcConnStateTimer UeInactiveTimer Ue inactive timer eNodeB
LST
RRCCONNSTATET
IMER
MOD
RRCCONNSTATET
IMER
RrcConnStateTimer UlSynTimer UlSynTimer eNodeB
LST
RRCCONNSTATET
IMER
ADD
TCEIPMAPPING
LST
TCEIPMAPPING
TceIpMapping TceId TCE ID eNodeB
MOD
TCEIPMAPPING
RMV
TCEIPMAPPING
ADD
TCEIPMAPPING
MOD
TceIpMapping IPMode IP Mode eNodeB
TCEIPMAPPING
LST
TCEIPMAPPING
ADD
TCEIPMAPPING
MOD
TceIpMapping TceIpV4Addr TCE IPv4 Address eNodeB
TCEIPMAPPING
LST
TCEIPMAPPING
ADD
TCEIPMAPPING
MOD
TceIpMapping TceIpV6Addr TCE IPv6 Address eNodeB
TCEIPMAPPING
LST
TCEIPMAPPING
ADD
ENBCELLQCIRSV
DPARA
LST
ENBCELLQCIRSV
DPARA
eNBCellQciRsvdPar LocalCellId Local cell ID eNodeB
MOD
ENBCELLQCIRSV
DPARA
RMV
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
LST
ENBCELLQCIRSV
QoS Class DPARA
eNBCellQciRsvdPar Qci eNodeB
Indication MOD
ENBCELLQCIRSV
DPARA
RMV
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved Switch
eNBCellQciRsvdPar RsvdSwPara0 eNodeB ENBCELLQCIRSV
Parameter 0
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved Switch
Parameter 1
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved Switch
Parameter 2
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
eNBCellQciRsvdPar RsvdPara2 eNodeB ENBCELLQCIRSV
Parameter 2
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 3
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 4
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 5
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 6
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 7
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 8
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 9
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 10
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 11
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 12
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 13
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 14
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 15
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 16
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 17
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 18
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 19
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 20
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCELLQCIRSV
DPARA
MOD
Reserved
Parameter 21
DPARA
LST
ENBCELLQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
LST
ENBCNOPQCIRSV
DPARA
eNBCnOpQciRsvdPaCnOperatorId CN Operator ID eNodeB
MOD
ENBCNOPQCIRSV
DPARA
RMV
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
LST
ENBCNOPQCIRSV
QoS Class DPARA
eNBCnOpQciRsvdPaQci eNodeB
Indication MOD
ENBCNOPQCIRSV
DPARA
RMV
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved Switch
eNBCnOpQciRsvdPaRsvdSwPara0 eNodeB ENBCNOPQCIRSV
Parameter 0
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved Switch
Parameter 1
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved Switch
Parameter 2
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
eNBCnOpQciRsvdPaRsvdPara2 eNodeB ENBCNOPQCIRSV
Parameter 2
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 3
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 4
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 5
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 6
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 7
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 8
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 9
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 10
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 11
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 12
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 13
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 14
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 15
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 16
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 17
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 18
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 19
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 20
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPQCIRSV
DPARA
MOD
Reserved
Parameter 21
DPARA
LST
ENBCNOPQCIRSV
DPARA
ADD
ENBCNOPRSVDP
ARA
LST
ENBCNOPRSVDP
ARA
eNBCnOpRsvdPara CnOperatorId CN Operator ID eNodeB
MOD
ENBCNOPRSVDP
ARA
RMV
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved Switch
eNBCnOpRsvdPara RsvdSwPara0 eNodeB ENBCNOPRSVDP
Parameter 0
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved Switch
Parameter 1
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved Switch
Parameter 2
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
eNBCnOpRsvdPara RsvdPara2 eNodeB ENBCNOPRSVDP
Parameter 2
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 3
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 4
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 5
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 6
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 7
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 8
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 9
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 10
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 11
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 12
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 13
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 14
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 15
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 16
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 17
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 18
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 19
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 20
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBCNOPRSVDP
ARA
MOD
Reserved
Parameter 21
ARA
LST
ENBCNOPRSVDP
ARA
ADD
ENBQCIRSVDPAR
A
LST
ENBQCIRSVDPAR
QoS Class A
eNBQciRsvdPara Qci eNodeB
Indication MOD
ENBQCIRSVDPAR
A
RMV
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved Switch
eNBQciRsvdPara RsvdSwPara0 eNodeB ENBQCIRSVDPAR
Parameter 0
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved Switch
Parameter 1
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved Switch
Parameter 2
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
eNBQciRsvdPara RsvdPara2 eNodeB ENBQCIRSVDPAR
Parameter 2
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 3
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 4
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 5
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 6
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 7
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 8
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 9
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 10
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 11
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 12
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 13
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 14
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 15
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 16
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 17
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 18
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 19
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 20
A
LST
ENBQCIRSVDPAR
A
ADD
ENBQCIRSVDPAR
A
MOD
Reserved
Parameter 21
A
LST
ENBQCIRSVDPAR
A
LST
CELLDLPCPDSCH
PA
CellDlpcPdschPa LocalCellId Local cell ID eNodeB
MOD
CELLDLPCPDSCH
PA
MOD
CELLDLPCPDSCH
PA
CellDlpcPdschPa PdschPaAdjSwitch PA adjusting switch eNodeB
LST
CELLDLPCPDSCH
PA
MOD
CELLDLPCPDSCH
PA for even power PA
CellDlpcPdschPa PaPcOff eNodeB
distribution LST
CELLDLPCPDSCH
PA
LST
CELLDRXPARA
CellDrxPara LocalCellId Local cell ID eNodeB
MOD
CELLDRXPARA
MOD
FDD enter DRX CELLDRXPARA
CellDrxPara FddEnterDrxThd eNodeB
threshold LST
CELLDRXPARA
MOD
FDD exit DRX CELLDRXPARA
CellDrxPara FddExitDrxThd eNodeB
threshold LST
CELLDRXPARA
MOD
TDD enter DRX CELLDRXPARA
CellDrxPara TddEnterDrxThdUl eNodeB
threshold Uplink LST
CELLDRXPARA
MOD
TDD exit DRX CELLDRXPARA
CellDrxPara TddExitDrxThdUl eNodeB
threshold Uplink LST
CELLDRXPARA
MOD
TDD enter DRX CELLDRXPARA
CellDrxPara TddEnterDrxThdDl eNodeB
threshold Downlink LST
CELLDRXPARA
MOD
TDD exit DRX CELLDRXPARA
CellDrxPara TddExitDrxThdDl eNodeB
threshold Downlink LST
CELLDRXPARA
MOD
DataAmountStatTi Data amount CELLDRXPARA
CellDrxPara eNodeB
mer Statistic timer LST
CELLDRXPARA
LST
CELLULPCDEDIC
CellUlpcDedic LocalCellId Local cell ID eNodeB
MOD
CELLULPCDEDIC
MOD
Delta-MCS enable CELLULPCDEDIC
CellUlpcDedic DeltaMcsEnabled eNodeB
or disable indication LST
CELLULPCDEDIC
Power Offset of
MOD
SRS to PUSCH
PSrsOffsetDeltaMc CELLULPCDEDIC
CellUlpcDedic with eNodeB
sDisable LST
DeltaMcsEnabled
CELLULPCDEDIC
Off
Power Offset of
MOD
SRS to PUSCH
PSrsOffsetDeltaMc CELLULPCDEDIC
CellUlpcDedic with eNodeB
sEnable LST
DeltaMcsEnabled
CELLULPCDEDIC
On
MOD
RSRP filtering CELLULPCDEDIC
CellUlpcDedic FilterRsrp eNodeB
coefficient LST
CELLULPCDEDIC
LST
DISTBASEDHO
DistBasedHO LocalCellId Local cell ID eNodeB
MOD
DISTBASEDHO
MOD
Distance-based
DistBasedMeasObj DISTBASEDHO
DistBasedHO Measurement eNodeB
Type LST
Object Type
DISTBASEDHO
MOD
Distance-based
DISTBASEDHO
DistBasedHO DistBasedHOThd Handover eNodeB
LST
Threshold
DISTBASEDHO
ADD
DRXPARAGROUP
LST
DRXPARAGROUP
DrxParaGroup LocalCellId Local cell ID eNodeB
MOD
DRXPARAGROUP
RMV
DRXPARAGROUP
ADD
DRXPARAGROUP
LST
DRX parameter DRXPARAGROUP
DrxParaGroup DrxParaGroupId eNodeB
group ID MOD
DRXPARAGROUP
RMV
DRXPARAGROUP
ADD
DRXPARAGROUP
MOD
DrxParaGroup EnterDrxSwitch Enter DRX Switch eNodeB
DRXPARAGROUP
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
MOD
DrxParaGroup OnDurationTimer On Duration Timer eNodeB
DRXPARAGROUP
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
DRX Inactivity MOD
DrxParaGroup DrxInactivityTimer eNodeB
Timer DRXPARAGROUP
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
DRX
MOD
DrxParaGroup DrxReTxTimer Retransmission eNodeB
DRXPARAGROUP
Timer
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
MOD
DrxParaGroup LongDrxCycle Long DRX Cycle eNodeB
DRXPARAGROUP
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
Short-cycle DRX
MOD
DrxParaGroup SupportShortDrx supported eNodeB
DRXPARAGROUP
indication
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
MOD
DrxParaGroup ShortDrxCycle Short DRX Cycle eNodeB
DRXPARAGROUP
LST
DRXPARAGROUP
ADD
DRXPARAGROUP
DRX Short Cycle MOD
DrxParaGroup DrxShortCycleTimer eNodeB
Timer DRXPARAGROUP
LST
DRXPARAGROUP
ADD
INTERRATHOCOM
MGROUP
LST
INTERRATHOCOM
MGROUP
InterRatHoCommGroLocalCellId Local cell ID eNodeB
MOD
INTERRATHOCOM
MGROUP
RMV
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
LST
INTERRATHOCOM
InterRatHoCommGr InterRAT handover MGROUP
InterRatHoCommGro eNodeB
oupId common group ID MOD
INTERRATHOCOM
MGROUP
RMV
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
InterRatHoA1A2Hy InterRAT A1A2
InterRatHoCommGro eNodeB INTERRATHOCOM
st hysteresis
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
InterRatHoA1A2Tim InterRAT A1A2 time
eToTrig to trigger
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
InterRatHoA1ThdR InterRAT A1 RSRP
srp trigger threshold
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
InterRatHoA1ThdR InterRAT A1 RSRQ
srq trigger threshold
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
InterRatHoA2ThdR InterRAT A2 RSRP
srp trigger threshold
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
InterRatHoA2ThdR InterRAT A2 RSRQ
srq trigger threshold
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCOM
MGROUP
MOD
BlindHoA2ThdOffse Blind HO A2
t Threshold Offset
MGROUP
LST
INTERRATHOCOM
MGROUP
ADD
INTERRATHOCDM
A1XRTTGROUP
LST
INTERRATHOCDM
A1XRTTGROUP
InterRatHoCdma1xRtLocalCellId Local cell ID eNodeB
MOD
INTERRATHOCDM
A1XRTTGROUP
RMV
INTERRATHOCDM
A1XRTTGROUP
ADD
INTERRATHOCDM
A1XRTTGROUP
LST
InterRAT handover INTERRATHOCDM
InterRatHoCdma1x to A1XRTTGROUP
InterRatHoCdma1xRt eNodeB
RttGroupId CDMA20001xRTT MOD
group ID INTERRATHOCDM
A1XRTTGROUP
RMV
INTERRATHOCDM
A1XRTTGROUP
ADD
INTERRATHOCDM
A1XRTTGROUP
CDMA20001XRTT MOD
InterRatHoCdmaB1
InterRatHoCdma1xRt handover eNodeB INTERRATHOCDM
Hyst
hysteresis A1XRTTGROUP
LST
INTERRATHOCDM
A1XRTTGROUP
ADD
INTERRATHOCDM
A1XRTTGROUP
CoverageBased MOD
InterRatHoCdmaB1
InterRatHoCdma1xRt CDMA20001XRTT eNodeB INTERRATHOCDM
ThdPs
trigger threshold A1XRTTGROUP
LST
INTERRATHOCDM
A1XRTTGROUP
ADD
INTERRATHOCDM
A1XRTTGROUP
MOD
InterRatHoCdmaB1 CDMA20001XRTT
InterRatHoCdma1xRt eNodeB INTERRATHOCDM
TimeToTrig time to trigger
A1XRTTGROUP
LST
INTERRATHOCDM
A1XRTTGROUP
ADD
INTERRATHOCDM
A1XRTTGROUP
Load Service
MOD
LdSvBasedHoCdm Based
InterRatHoCdma1xRt eNodeB INTERRATHOCDM
aB1ThdPs CDMA20001XRTT
A1XRTTGROUP
trigger threshold
LST
INTERRATHOCDM
A1XRTTGROUP
ADD
RLFTIMERCONST
GROUP
LST
RLFTIMERCONST
GROUP
RlfTimerConstGroup LocalCellId Local cell ID eNodeB
MOD
RLFTIMERCONST
GROUP
RMV
RLFTIMERCONST
GROUP
ADD
RLFTIMERCONST
GROUP
LST
RLFTIMERCONST
RlfTimerConstGrou RLF timer and GROUP
RlfTimerConstGroup eNodeB
pId constants group ID MOD
RLFTIMERCONST
GROUP
RMV
RLFTIMERCONST
GROUP
ADD
RLFTIMERCONST
GROUP
MOD
RlfTimerConstGroup T301 Timer 301 eNodeB RLFTIMERCONST
GROUP
LST
RLFTIMERCONST
GROUP
ADD
RLFTIMERCONST
GROUP
MOD
GROUP
LST
RLFTIMERCONST
GROUP
ADD
RLFTIMERCONST
GROUP
MOD
GROUP
LST
RLFTIMERCONST
GROUP
ADD
RLFTIMERCONST
GROUP
MOD
RlfTimerConstGroup N310 Constant N310 eNodeB RLFTIMERCONST
GROUP
LST
RLFTIMERCONST
GROUP
ADD
RLFTIMERCONST
GROUP
MOD
RlfTimerConstGroup N311 Constant N311 eNodeB RLFTIMERCONST
GROUP
LST
RLFTIMERCONST
GROUP
ADD
CELLEXTENDEDQ
CI
LST
CELLEXTENDEDQ
CI
CellExtendedQci ExtendedQci Extended QCI eNodeB
MOD
CELLEXTENDEDQ
CI
RMV
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
LST
CELLEXTENDEDQ
CI
CellExtendedQci LocalCellId Local cell ID eNodeB
MOD
CELLEXTENDEDQ
CI
RMV
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
InterFreqHoGroupI Interfreq handover
CellExtendedQci eNodeB CELLEXTENDEDQ
d group ID
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
InterRAT handover
MOD
InterRatHoCdma1x to
RttGroupId CDMA20001xRTT
CI
group ID
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
InterRAT handover
MOD
InterRatHoCdmaHr to
pdGroupId CDMA2000HRPD
CI
group ID
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
InterRatHoCommGr InterRAT handover
oupId common group ID
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
InterRatHoGeranGr InterRAT handover
oupId to GERAN group ID
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
InterRatHoUtranGro InterRAT handover
upId to UTRAN Group ID
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
IntraFreqHoGroupI Intrafreq handover
d group ID
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
DRX parameter
CellExtendedQci DrxParaGroupId eNodeB CELLEXTENDEDQ
group ID
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
RlfTimerConstCfgIn RLF timer and
d constants indication
CI
LST
CELLEXTENDEDQ
CI
ADD
CELLEXTENDEDQ
CI
MOD
RlfTimerConstGrou RLF timer and
pId constants group ID
CI
LST
CELLEXTENDEDQ
CI
LST
CELLSTANDARDQ
CI
CellStandardQci LocalCellId Local cell ID eNodeB
MOD
CELLSTANDARDQ
CI
LST
CELLSTANDARDQ
QoS Class CI
CellStandardQci Qci eNodeB
Indication MOD
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
InterFreqHoGroupI Interfreq handover CI
CellStandardQci eNodeB
d group ID LST
CELLSTANDARDQ
CI
MOD
InterRAT handover CELLSTANDARDQ
InterRatHoCdma1x to CI
RttGroupId CDMA20001xRTT LST
group ID CELLSTANDARDQ
CI
MOD
InterRAT handover CELLSTANDARDQ
InterRatHoCdmaHr to CI
pdGroupId CDMA2000HRPD LST
group ID CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
InterRatHoCommGr InterRAT handover CI
oupId common group ID LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
InterRatHoGeranGr InterRAT handover CI
oupId to GERAN group ID LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
InterRatHoUtranGro InterRAT handover CI
upId to UTRAN Group ID LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
IntraFreqHoGroupI Intrafreq handover CI
d group ID LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
DRX parameter CI
CellStandardQci DrxParaGroupId eNodeB
group ID LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
CI
CellStandardQci SriPeriod SRI Period eNodeB
LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
RlfTimerConstCfgIn RLF timer and CI
d constants indication LST
CELLSTANDARDQ
CI
MOD
CELLSTANDARDQ
RlfTimerConstGrou RLF timer and CI
pId constants group ID LST
CELLSTANDARDQ
CI
ADD
INTERRATHOCDM
AHRPDGROUP
LST
INTERRATHOCDM
AHRPDGROUP
InterRatHoCdmaHrp LocalCellId Local cell ID eNodeB
MOD
INTERRATHOCDM
AHRPDGROUP
RMV
INTERRATHOCDM
AHRPDGROUP
ADD
INTERRATHOCDM
AHRPDGROUP
LST
InterRAT handover INTERRATHOCDM
InterRatHoCdmaHr to AHRPDGROUP
InterRatHoCdmaHrp eNodeB
pdGroupId CDMA2000HRPD MOD
group ID INTERRATHOCDM
AHRPDGROUP
RMV
INTERRATHOCDM
AHRPDGROUP
ADD
INTERRATHOCDM
AHRPDGROUP
CDMA2000HRPD MOD
InterRatHoCdmaB1
InterRatHoCdmaHrp handover eNodeB INTERRATHOCDM
Hyst
hysteresis AHRPDGROUP
LST
INTERRATHOCDM
AHRPDGROUP
ADD
INTERRATHOCDM
AHRPDGROUP
CoverageBased MOD
InterRatHoCdmaB1
InterRatHoCdmaHrp CDMA2000HRPD eNodeB INTERRATHOCDM
ThdPs
trigger threshold AHRPDGROUP
LST
INTERRATHOCDM
AHRPDGROUP
ADD
INTERRATHOCDM
AHRPDGROUP
MOD
InterRatHoCdmaB1 CDMA2000HRPD
InterRatHoCdmaHrp eNodeB INTERRATHOCDM
TimeToTrig time to trigger
AHRPDGROUP
LST
INTERRATHOCDM
AHRPDGROUP
ADD
INTERRATHOCDM
AHRPDGROUP
Load Service
MOD
LdSvBasedHoCdm Based
InterRatHoCdmaHrp eNodeB INTERRATHOCDM
aB1ThdPs CDMA2000HRPD
AHRPDGROUP
trigger threshold
LST
INTERRATHOCDM
AHRPDGROUP
ADD
INTERRATHOGER
ANGROUP
LST
INTERRATHOGER
ANGROUP
InterRatHoGeranGroLocalCellId Local cell ID eNodeB
MOD
INTERRATHOGER
ANGROUP
RMV
INTERRATHOGER
ANGROUP
ADD
INTERRATHOGER
ANGROUP
LST
INTERRATHOGER
InterRatHoGeranGr InterRAT handover ANGROUP
InterRatHoGeranGro eNodeB
oupId to GERAN group ID MOD
INTERRATHOGER
ANGROUP
RMV
INTERRATHOGER
ANGROUP
ADD
INTERRATHOGER
ANGROUP
MOD
InterRatHoGeranB1 GERAN handover
InterRatHoGeranGro eNodeB INTERRATHOGER
Hyst hysteresis
ANGROUP
LST
INTERRATHOGER
ANGROUP
ADD
INTERRATHOGER
ANGROUP
CoverageBased MOD
InterRatHoGeranB1
InterRatHoGeranGro GERAN trigger eNodeB INTERRATHOGER
Thd
threshold ANGROUP
LST
INTERRATHOGER
ANGROUP
ADD
INTERRATHOGER
ANGROUP
MOD
InterRatHoGeranB1 GERAN time to
TimeToTrig trigger
ANGROUP
LST
INTERRATHOGER
ANGROUP
ADD
INTERRATHOGER
ANGROUP
Load Service
MOD
LdSvBasedHoGera Based Geran
nB1Thd EventB1 trigger
ANGROUP
threshold
LST
INTERRATHOGER
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
LST
INTERRATHOUTR
ANGROUP
InterRatHoUtranGro LocalCellId Local cell ID eNodeB
MOD
INTERRATHOUTR
ANGROUP
RMV
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
LST
INTERRATHOUTR
InterRatHoUtranGro InterRAT handover ANGROUP
InterRatHoUtranGro eNodeB
upId to UTRAN Group ID MOD
INTERRATHOUTR
ANGROUP
RMV
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
CoverageBased MOD
InterRatHoUtranB1
InterRatHoUtranGro UTRAN ECN0 eNodeB INTERRATHOUTR
ThdEcn0
trigger threshold ANGROUP
LST
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
CoverageBased MOD
InterRatHoUtranB1
InterRatHoUtranGro UTRAN RSCP eNodeB INTERRATHOUTR
ThdRscp
trigger threshold ANGROUP
LST
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
MOD
InterRatHoUtranB1 UTRAN handover
InterRatHoUtranGro eNodeB INTERRATHOUTR
Hyst hysteresis
ANGROUP
LST
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
MOD
InterRatHoUtranB1 UTRAN time to
TimeToTrig trigger
ANGROUP
LST
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
Load Service MOD
LdSvBasedHoUtran
InterRatHoUtranGro Based UTRANB1 eNodeB INTERRATHOUTR
B1ThdEcn0
ECN0 threshold ANGROUP
LST
INTERRATHOUTR
ANGROUP
ADD
INTERRATHOUTR
ANGROUP
Load Service
MOD
LdSvBasedHoUtran Based UTRAN
B1ThdRscp EventB1 RSCP
ANGROUP
trigger threshold
LST
INTERRATHOUTR
ANGROUP
ADD
INTERFREQHOGR
OUP
LST
INTERFREQHOGR
OUP
InterFreqHoGroup LocalCellId Local cell ID eNodeB
MOD
INTERFREQHOGR
OUP
RMV
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
LST
INTERFREQHOGR
InterFreqHoGroupI Interfreq handover OUP
InterFreqHoGroup eNodeB
d group ID MOD
INTERFREQHOGR
OUP
RMV
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA1A2H Interfreq A1A2
InterFreqHoGroup eNodeB INTERFREQHOGR
yst hysteresis
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA1A2Ti Interfreq A1A2 time
meToTrig to trigger
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA1Thd Interfreq A1 RSRP
Rsrp threshold
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA1Thd Interfreq A1 RSRQ
Rsrq threshold
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA2Thd Interfreq A2 RSRP
Rsrp threshold
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA2Thd Interfreq A2 RSRQ
Rsrq threshold
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
Interfreq handover
InterFreqHoGroup InterFreqHoA4Hyst eNodeB INTERFREQHOGR
hysteresis
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
CoverageBased MOD
InterFreqHoA4Thd
InterFreqHoGroup Interfreq RSRP eNodeB INTERFREQHOGR
Rsrp
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
CoverageBased MOD
InterFreqHoA4Thd
InterFreqHoGroup Interfreq RSRQ eNodeB INTERFREQHOGR
Rsrq
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA4Time Interfreq HandOver
ToTrig Time to Trigger
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
Load Based MOD
InterFreqLoadBase
InterFreqHoGroup Interfreq RSRP eNodeB INTERFREQHOGR
dHoA4ThdRsrp
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
Load Based MOD
InterFreqLoadBase
InterFreqHoGroup Interfreq RSRQ eNodeB INTERFREQHOGR
dHoA4ThdRsrq
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
Freq Priority Based MOD
FreqPriInterFreqHo
InterFreqHoGroup Interfreq A1 RSRP eNodeB INTERFREQHOGR
A1ThdRsrp
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
FreqPriInterFreqHo
InterFreqHoGroup Interfreq A1 RSRQ eNodeB INTERFREQHOGR
A1ThdRsrq
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
InterFreqHoA3Offse
InterFreqHoGroup Interfreq A3 offset eNodeB INTERFREQHOGR
t
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
A3InterFreqHoA1T A3 based interfreq
hdRsrp A1 RSRP threshold
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
MOD
A3InterFreqHoA2T A3 based Interfreq
hdRsrp A2 RSRP threshold
OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
FreqPriInterFreqHo
InterFreqHoGroup Interfreq A2 RSRP eNodeB INTERFREQHOGR
A2ThdRsrp
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTERFREQHOGR
OUP
FreqPriInterFreqHo
InterFreqHoGroup Interfreq A2 RSRQ eNodeB INTERFREQHOGR
A2ThdRsrq
threshold OUP
LST
INTERFREQHOGR
OUP
ADD
INTRAFREQHOGR
OUP
LST
INTRAFREQHOGR
OUP
IntraFreqHoGroup LocalCellId Local cell ID eNodeB
MOD
INTRAFREQHOGR
OUP
RMV
INTRAFREQHOGR
OUP
ADD
INTRAFREQHOGR
OUP
LST
INTRAFREQHOGR
IntraFreqHoGroupI Intrafreq handover OUP
IntraFreqHoGroup eNodeB
d group ID MOD
INTRAFREQHOGR
OUP
RMV
INTRAFREQHOGR
OUP
ADD
INTRAFREQHOGR
OUP
MOD
Intrafreq handover
IntraFreqHoGroup IntraFreqHoA3Hyst eNodeB INTRAFREQHOGR
hysteresis
OUP
LST
INTRAFREQHOGR
OUP
ADD
INTRAFREQHOGR
OUP
MOD
IntraFreqHoA3Offse Intrafreq handover
IntraFreqHoGroup eNodeB INTRAFREQHOGR
t offset
OUP
LST
INTRAFREQHOGR
OUP
ADD
INTRAFREQHOGR
OUP
MOD
IntraFreqHoA3Time Intrafreq handover
IntraFreqHoGroup eNodeB INTRAFREQHOGR
ToTrig time to trigger
OUP
LST
INTRAFREQHOGR
OUP
ADD
CNOPERATOR
LST
CNOPERATOR
CnOperator CnOperatorId CN Operator ID eNodeB
MOD
CNOPERATOR
RMV
CNOPERATOR
ADD
CNOPERATOR
MOD
CnOperator CnOperatorName CN Operator name eNodeB
CNOPERATOR
LST
CNOPERATOR
ADD
CNOPERATOR
MOD
CnOperator CnOperatorType CN Operator type eNodeB
CNOPERATOR
LST
CNOPERATOR
ADD
CNOPERATOR
Mobile country MOD
CnOperator Mcc eNodeB
code CNOPERATOR
LST
CNOPERATOR
ADD
CNOPERATOR
Mobile network MOD
CnOperator Mnc eNodeB
code CNOPERATOR
LST
CNOPERATOR
ADD
CNOPERATORIPP
ATH
LST
CNOPERATORIPP
ATH
CnOperatorIpPath IpPathId IP path ID eNodeB
MOD
CNOPERATORIPP
ATH
RMV
CNOPERATORIPP
ATH
ADD
CNOPERATORIPP
ATH
MOD
CnOperatorIpPath CnOperatorId CN Operator ID eNodeB CNOPERATORIPP
ATH
LST
CNOPERATORIPP
ATH
ADD
CNOPERATORTA
LST
CNOPERATORTA
CnOperatorTa TrackingAreaId Tracking area ID eNodeB
MOD
CNOPERATORTA
RMV
CNOPERATORTA
ADD
CNOPERATORTA
MOD
CnOperatorTa CnOperatorId CN Operator ID eNodeB
CNOPERATORTA
LST
CNOPERATORTA
ADD
CNOPERATORTA
MOD
CnOperatorTa Tac Tracking area code eNodeB
CNOPERATORTA
LST
CNOPERATORTA
LST EMC
Emc CnOperatorId CN Operator ID eNodeB
MOD EMC
Emergency call MOD EMC

Emc EmcEnable eNodeB
enabled switch LST EMC
Emergency call
EmcEnableInLimite MOD EMC
Emc enabled switch in eNodeB
dMode LST EMC
limited mode
EmcDedicatedBear The ARP of EMC MOD EMC

Emc eNodeB
erARP dedicated bearer LST EMC
EmcDefaultBearerA The ARP of EMC MOD EMC
Emc eNodeB
RP default bearer LST EMC
MOD
ENODEBSHARING
ENodeBSharingMo eNodeB sharing MODE
ENodeBSharingMod eNodeB
de mode LST
ENODEBSHARING
MODE
ADD
LICENSESHARING
POLICY
LST
LICENSESHARING
POLICY
LicenseSharingPolic CnOperatorId CN Operator ID eNodeB
MOD
LICENSESHARING
POLICY
RMV
LICENSESHARING
POLICY
ADD
LICENSESHARING
POLICY
The proportion of MOD
LicenseSharingPolic MaxUserNumRate the maximum eNodeB LICENSESHARING
number of users POLICY
LST
LICENSESHARING
POLICY
MOD
S1 reestablish min S1REESTTIMER
S1ReestTimer S1ReestMinTimer eNodeB
timer length LST
S1REESTTIMER
MOD
S1 reestablish max S1REESTTIMER
S1ReestTimer S1ReestMaxTimer eNodeB
timer length LST
S1REESTTIMER
S1INTERFACE
BLK
S1INTERFACE
DSP
S1INTERFACE
MOD
S1Interface S1InterfaceId S1Interface ID eNodeB
S1INTERFACE
RMV
S1INTERFACE
RST
S1INTERFACE
ADD
UBL
S1INTERFACE
MOD
S1Interface S1SctpLinkId S1 SCTP link ID eNodeB
S1INTERFACE
DSP
S1INTERFACE
ADD
S1INTERFACE
MOD
S1Interface CnOperatorId CN Operator ID eNodeB
S1INTERFACE
DSP
S1INTERFACE
ADD
S1INTERFACE
MOD
S1Interface MmeRelease MME Release eNodeB
S1INTERFACE
DSP
S1INTERFACE
ADD
S1INTERFACE
MOD
S1Interface S1InterfaceIsBlock S1Interface is block eNodeB
S1INTERFACE
DSP
S1INTERFACE
DSP
S1Interface S1InterfaceState S1Interface state eNodeB
S1INTERFACE
DSP
S1Interface S1SctpLinkState S1 SCTP Link State eNodeB
S1INTERFACE
DSP
S1Interface MmeIsOverLoad MME is overloaded eNodeB
S1INTERFACE
S1InterfaceUserNu S1Interface user DSP

S1Interface eNodeB
m number S1INTERFACE
DSP
S1Interface MmeName MME name eNodeB
S1INTERFACE
DSP
S1Interface ServedPlmns Served PLMNs eNodeB
S1INTERFACE
DSP
S1Interface ServedGummeis Served GUMMEIs eNodeB
S1INTERFACE
MME relative DSP

S1Interface RelativeMmeCap eNodeB
capacity S1INTERFACE
S1 Link Fault DSP

S1Interface S1LinkFaultReason eNodeB
Reason S1INTERFACE
LST
MMEFEATURECF
G
MmeFeatureCfg S1InterfaceId S1Interface ID eNodeB
MOD
MMEFEATURECF
G
MOD
MMEFEATURECF
MME supporting G
MmeFeatureCfg MdtEnable eNodeB
MDT or not LST
MMEFEATURECF
G
ADD
X2BLACKWHITELI
ST
RMV
Mobile country
X2BlackWhiteList Mcc eNodeB X2BLACKWHITELI
code
ST
LST
X2BLACKWHITELI
ST
ADD
X2BLACKWHITELI
ST
RMV
Mobile network
X2BlackWhiteList Mnc eNodeB X2BLACKWHITELI
code
ST
LST
X2BLACKWHITELI
ST
ADD
X2BLACKWHITELI
ST
RMV
X2BlackWhiteList ENodeBId eNodeB ID eNodeB X2BLACKWHITELI
ST
LST
X2BLACKWHITELI
ST
ADD
X2BLACKWHITELI
X2 Black or White ST
X2BlackWhiteList X2ListType eNodeB
List Type LST
X2BLACKWHITELI
ST
ADD
X2INTERFACE
DSP
X2INTERFACE
MOD
X2Interface X2InterfaceId X2Interface ID eNodeB
X2INTERFACE
RMV
X2INTERFACE
RST
X2INTERFACE
ADD
X2INTERFACE
MOD
X2Interface X2SctpLinkId X2 SCTP link ID eNodeB
X2INTERFACE
DSP
X2INTERFACE
ADD
X2INTERFACE
MOD
X2Interface CnOperatorId CN Operator ID eNodeB
X2INTERFACE
DSP
X2INTERFACE
ADD
X2INTERFACE
TargetENodeBRele Target eNodeB MOD
X2Interface eNodeB
ase release X2INTERFACE
DSP
X2INTERFACE
ADD
X2INTERFACE
Automatic removal MOD
X2Interface NoAutoRmvFlag eNodeB
flag X2INTERFACE
DSP
X2INTERFACE
Neighbor eNodeB DSP

X2Interface NbrENodeBId eNodeB
ID X2INTERFACE
Neighbor eNodeB DSP

X2Interface NbrENodeBPlmnId eNodeB
PLMN ID X2INTERFACE
DSP
X2Interface X2InterfaceState X2Interface state eNodeB
X2INTERFACE
X2AbnormalReaso X2Interface state DSP
X2Interface eNodeB
n abnormal reason X2INTERFACE
MOD DRX
Drx DrxAlgSwitch DRX switch eNodeB
LST DRX
Short-cycle DRX MOD DRX

Drx ShortDrxSwitch eNodeB
switch LST DRX
LongDrxCycleSpeci Special long DRX MOD DRX
Drx eNodeB
al cycle LST DRX
OnDurationTimerSp Special On MOD DRX
Drx eNodeB
ecial Duration timer LST DRX
DrxInactivityTimerS Special DRX MOD DRX
Drx eNodeB
pecial inactivity timer LST DRX
Special short-cycle
SupportShortDrxSp MOD DRX
Drx DRX supported eNodeB
ecial LST DRX
indication
ShortDrxCycleSpeci Special short DRX MOD DRX
Drx eNodeB
al cycle LST DRX
DrxShortCycleTimer Special DRX short MOD DRX

Drx eNodeB
Special cycle timer LST DRX
LongDrxCycleForA Long DRX Cycle for MOD DRX
Drx eNodeB
nr ANR LST DRX
LongDRXCycleforI Long DRX Cycle for MOD DRX

Drx eNodeB
RatAnr Inter-RAT ANR LST DRX
ADD
EXTENDEDQCI
LST
Extended QoS EXTENDEDQCI
ExtendedQci ExtendedQci eNodeB
Class Identifier MOD
EXTENDEDQCI
RMV
EXTENDEDQCI
ADD
EXTENDEDQCI
MOD
ExtendedQci ServiceType Service type eNodeB
EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
Uplink scheduling MOD
ExtendedQci UlschPriorityFactor eNodeB
priority factor EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
Downlink
MOD
ExtendedQci DlschPriorityFactor scheduling priority eNodeB
EXTENDEDQCI
factor
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
MOD
ExtendedQci UlMinGbr Uplink MinGBR eNodeB
EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
MOD
ExtendedQci DlMinGbr Downlink MinGBR eNodeB
EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
PreAllocationWeigh Pre-allocation MOD
ExtendedQci eNodeB
t weight EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
InterRatPolicyCfgGr InterRAT policy MOD
ExtendedQci eNodeB
oupId config group ID EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
MOD
ExtendedQci PrioritisedBitRate Prioritised bit rate eNodeB
EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
LogicalChannelPrio Logical channel MOD
ExtendedQci eNodeB
rity priority EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
RlcPdcpParaGroupI RLC PDCP MOD
ExtendedQci eNodeB
d parameter group ID EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
MOD
ExtendedQci FreeUserFlag Free user flag eNodeB
EXTENDEDQCI
LST
EXTENDEDQCI
ADD
EXTENDEDQCI
MOD
ExtendedQci FlowCtrlType Flow Control Type eNodeB
EXTENDEDQCI
LST
EXTENDEDQCI
ADD
INTERRATPOLICY
CFGGROUP
LST
INTERRATPOLICY
InterRatPolicyCfgGr InterRAT policy CFGGROUP
InterRatPolicyCfgGr eNodeB
oupId config group ID MOD
INTERRATPOLICY
CFGGROUP
RMV
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
MOD
UTRAN handover
InterRatPolicyCfgGr UtranHoCfg eNodeB INTERRATPOLICY
policy Configuration
CFGGROUP
LST
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
GERAN GSM MOD
InterRatPolicyCfgGr GeranGsmHoCfg handover policy eNodeB INTERRATPOLICY
Configuration CFGGROUP
LST
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
GERAN GPRS MOD
GeranGprsEdgeHo
InterRatPolicyCfgGr EDGE handover eNodeB INTERRATPOLICY
Cfg
policy Configuration CFGGROUP
LST
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
CDMA2000 1XRTT MOD
InterRatPolicyCfgGr Cdma1xRttHoCfg handover policy eNodeB INTERRATPOLICY
LST
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
CDMA2000 HRPD MOD
InterRatPolicyCfgGr CdmaHrpdHoCfg handover policy eNodeB INTERRATPOLICY
LST
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
MOD
InterRatPolicyCfgGr NoHoFlag No handover flag eNodeB INTERRATPOLICY
CFGGROUP
LST
INTERRATPOLICY
CFGGROUP
ADD
INTERRATPOLICY
CFGGROUP
MOD
InterRatPolicyCfgGr NoFastAnrFlag No fast ANR flag eNodeB INTERRATPOLICY
CFGGROUP
LST
INTERRATPOLICY
CFGGROUP
MOD
Delta Offset CQI PUSCHPARAM
PuschParam DeltaOffsetCqiIndex eNodeB
Index LST
PUSCHPARAM
MOD
Delta Offset RI PUSCHPARAM
PuschParam DeltaOffsetRiIndex eNodeB
Index LST
PUSCHPARAM
MOD
DeltaOffsetAckInde Delta Offset PUSCHPARAM
PuschParam eNodeB
x Acknowledge Index LST
PUSCHPARAM
ADD
RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
RlcPdcpParaGroupI RLC PDCP OUP
RlcPdcpParaGroup eNodeB
d parameter group ID MOD
RLCPDCPPARAGR
OUP
RMV
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RlcPdcpParaGroup DiscardTimer Discard timer eNodeB RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RLC-UM or RLC-
RlcPdcpParaGroup RlcMode eNodeB RLCPDCPPARAGR
AM mode
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
UeMaxRetxThresho MaxretxThreshold
RlcPdcpParaGroup eNodeB RLCPDCPPARAGR
ld for UE
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
ENodeBMaxRetxTh MaxRetxThreshold
reshold for eNodeB
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RlcPdcpParaGroup UePollByte PollByte for UE eNodeB RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
PollByte for
RlcPdcpParaGroup ENodeBPollByte eNodeB RLCPDCPPARAGR
eNodeB
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RlcPdcpParaGroup UePollPdu PollPdu for UE eNodeB RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RlcPdcpParaGroup ENodeBPollPdu PollPdu for eNodeB eNodeB RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
UePollRetransmitTi Poll retransmit timer
mer for UE
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
ENodeBPollRetrans Poll retransmit timer
mitTimer for eNodeB
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
UeStatusProhibitTi Status prohibit timer
mer for UE
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
ENodeBStatusProhi Status prohibit timer
bitTimer for eNodeB
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
UeAmReorderingTi AM reordering timer
mer for UE
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
ENodeBAmReorder AM reordering timer
ingTimer for eNodeB
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RlcPdcpParaGroup PdcpSnSize UM PDCP-SN size eNodeB RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
RlcPdcpParaGroup UlRlcSnSize Uplink RLC-Sn size eNodeB RLCPDCPPARAGR
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
Downlink RLC-SN
RlcPdcpParaGroup DlRlcSnSize eNodeB RLCPDCPPARAGR
size
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
UeUmReorderingTi UM reordering timer
mer for UE
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
MOD
ENodeBUmReorder UM reordering timer
ingTimer for eNodeB
OUP
LST
RLCPDCPPARAGR
OUP
ADD
RLCPDCPPARAGR
OUP
AM PDCP status MOD
RlcPdcpParaGroup PdcpStatusRptReq report required eNodeB RLCPDCPPARAGR
indication OUP
LST
RLCPDCPPARAGR
OUP
LST
QoS Class STANDARDQCI
StandardQci Qci eNodeB
Indication MOD
STANDARDQCI
MOD
STANDARDQCI
StandardQci UlschPriorityFactor Ulsch priority factor eNodeB
LST
STANDARDQCI
MOD
STANDARDQCI
StandardQci DlschPriorityFactor Dlsch priority factor eNodeB
LST
STANDARDQCI
MOD
STANDARDQCI
StandardQci UlMinGbr Uplink MinGBR eNodeB
LST
STANDARDQCI
MOD
STANDARDQCI
StandardQci DlMinGbr Downlink MinGBR eNodeB
LST
STANDARDQCI
MOD
PreAllocationWeigh Pre-allocation STANDARDQCI
StandardQci eNodeB
t weight LST
STANDARDQCI
MOD
InterRatPolicyCfgGr InterRAT policy STANDARDQCI
StandardQci eNodeB
oupId config group ID LST
STANDARDQCI
MOD
RlcPdcpParaGroupI RLC PDCP STANDARDQCI
StandardQci eNodeB
d parameter group ID LST
STANDARDQCI
MOD
STANDARDQCI
StandardQci PrioritisedBitRate Prioritised bit rate eNodeB
LST
STANDARDQCI
MOD
LogicalChannelPrio Logical channel STANDARDQCI
StandardQci eNodeB
rity priority LST
STANDARDQCI
MOD
STANDARDQCI
StandardQci FlowCtrlType Flow control type eNodeB
LST
STANDARDQCI
MOD
ALGODEFAULTPA
Default doppler RA
AlgoDefaultPara DefDopplerLevel eNodeB
level LST
ALGODEFAULTPA
RA
MOD
BFMIMOADAPTIVE
BfMimoAdaptiveSwi BfMIMO adaptive PARACFG
BfMimoAdaptivePara eNodeB
tch switch LST
BFMIMOADAPTIVE
PARACFG
MOD
BFMIMOADAPTIVE
Fixed BfMIMO PARACFG
BfMimoAdaptiveParaFixedBfMimoMode eNodeB
mode LST
BFMIMOADAPTIVE
PARACFG
MOD
CQI period adaptive CQIADAPTIVECFG
CqiAdaptiveCfg CqiPeriodAdaptive eNodeB
switch LST
CQIADAPTIVECFG
MOD
User CQI period CQIADAPTIVECFG
CqiAdaptiveCfg UserCqiPeriodCfg eNodeB
config LST
CQIADAPTIVECFG
MOD
MIMOADAPTIVEPA
MimoAdaptiveSwitc MIMO adaptive RACFG
MimoAdaptiveParaCf eNodeB
h switch LST
MIMOADAPTIVEPA
RACFG
MOD
MIMOADAPTIVEPA
RACFG
MimoAdaptiveParaCfFixedMimoMode Fixed MIMO mode eNodeB
LST
MIMOADAPTIVEPA
RACFG
MOD
SRSADAPTIVECF
SRS period G
SrsAdaptiveCfg SrsPeriodAdaptive eNodeB
adaptive switch LST
SRSADAPTIVECF
G
MOD
SRSADAPTIVECF
User SRS period G
SrsAdaptiveCfg UserSrsPeriodCfg eNodeB
config LST
SRSADAPTIVECF
G
LST TYPDRBBSR
TypDrbBsr Qci QoS Class Identifier eNodeB
MOD TYPDRBBSR
MOD TYPDRBBSR
TypDrbBsr TPerodicBSRTimer Periodic BSR Timer eNodeB
LST TYPDRBBSR
BSR
MOD TYPDRBBSR
TypDrbBsr RetxBsrTimer Retransmission eNodeB
LST TYPDRBBSR
Timer
MOD
GAP measurement HOMEASCOMM
HoMeasComm GapPatternType eNodeB
pattern LST
HOMEASCOMM
MOD
EutranFilterCoeffRs EUTRAN RSRP HOMEASCOMM
HoMeasComm eNodeB
rp filter coefficient LST
HOMEASCOMM
MOD
EutranFilterCoeffRs EUTRAN RSRQ HOMEASCOMM
HoMeasComm eNodeB
rq filter coefficient LST
HOMEASCOMM
MOD
GERAN filter HOMEASCOMM
HoMeasComm GeranFilterCoeff eNodeB
coefficient LST
HOMEASCOMM
MOD
HOMEASCOMM
HoMeasComm SMeasureInd SMeasureInd eNodeB
LST
HOMEASCOMM
MOD
HOMEASCOMM
HoMeasComm SMeasure SMeasure eNodeB
LST
HOMEASCOMM
MOD
HOMEASCOMM
HoMeasComm SpeedDepParaInd SpeedDependInd eNodeB
LST
HOMEASCOMM
MOD
TCRmax in HOMEASCOMM
HoMeasComm TcrMaxConnMode eNodeB
connected mode LST
HOMEASCOMM
MOD
TcrMaxHystConnM TCRmaxHyst in HOMEASCOMM
HoMeasComm eNodeB
ode connected mode LST
HOMEASCOMM
MOD
NcrMediumConnMo NCR Medium in HOMEASCOMM
HoMeasComm eNodeB
de connected mode LST
HOMEASCOMM
MOD
NCR High in HOMEASCOMM
HoMeasComm NcrHighConnMode eNodeB
connected mode LST
HOMEASCOMM
TTT Scaling factor MOD

for Medium mobility HOMEASCOMM
HoMeasComm TttSfMedium eNodeB
state in connected LST
mode HOMEASCOMM
TTT Scaling factor MOD
for High mobility HOMEASCOMM
HoMeasComm TttSfHigh eNodeB
state in connected LST
mode HOMEASCOMM
MOD
UtranFilterCoeffRsc UTRAN RSCP filter HOMEASCOMM
HoMeasComm eNodeB
p coefficient LST
HOMEASCOMM
MOD
UtranFilterCoeffEcn UTRAN ECN0 filter HOMEASCOMM
HoMeasComm eNodeB
0 coefficient LST
HOMEASCOMM
MOD
INTERRATHOCOM
InterRatHoMaxRprt Max report cell M
InterRatHoComm eNodeB
Cell number LST
INTERRATHOCOM
M
MOD
INTERRATHOCOM
InterRatHoRprtAmo Measurement M
unt report amount LST
INTERRATHOCOM
M
MOD
INTERRATHOCOM
Geran
InterRatHoGeranRp M
InterRatHoComm measurement eNodeB
rtInterval LST
report interval
INTERRATHOCOM
M
MOD
INTERRATHOCOM
InterRatHoUtranB1 Utran measurement M
MeasQuan trigger quantity LST
INTERRATHOCOM
M
MOD
INTERRATHOCOM
UTRAN FDD
InterRatHoUtranRpr M
tInterval LST
report interval
INTERRATHOCOM
M
MOD
INTERRATHOCOM
CDMA20001XRTT
InterRatHoCdma1x M
RttB1MeasQuan LST
trigger quantity
INTERRATHOCOM
M
MOD
INTERRATHOCOM
CDMA20001XRTT
InterRatCdma1xRtt M
RprtInterval LST
report interval
INTERRATHOCOM
M
MOD
INTERRATHOCOM
CDMA2000HRPD
InterRatHoCdmaHr M
pdB1MeasQuan LST
trigger quantity
INTERRATHOCOM
M
MOD
INTERRATHOCOM
CDMA2000HRPD
InterRatCdmaHrpd M
RprtInterval LST
report interval
INTERRATHOCOM
M
MOD
INTERRATHOCOM
InterRat A1A2
InterRatHoA1A2Tri M
gQuan LST
trigger quantity
INTERRATHOCOM
M
MOD
INTERRATHOCOM
InterRatHoEventTy Inter RAT HO M
pe Trigger Event Type LST
INTERRATHOCOM
M
MOD
INTRARATHOCOM
IntraRatHoMaxRprt Max report cell M
IntraRatHoComm eNodeB
Cell number LST
INTRARATHOCOM
M
MOD
INTRARATHOCOM
IntraRatHoRprtAmo Measurement M
unt report amount LST
INTRARATHOCOM
M
MOD
INTRARATHOCOM
IntraFreqHoA3Trig A3 measurement M
Quan trigger quantity LST
INTRARATHOCOM
M
MOD
INTRARATHOCOM
IntraFreqHoA3Rprt A3 measurement M
Quan report quantity LST
INTRARATHOCOM
M
MOD
INTRARATHOCOM
IntraFreqHoRprtInte A3 measurement M
rval report interval LST
INTRARATHOCOM
M
MOD
INTRARATHOCOM
InterFreqHoA4Rprt Measurement A4 M
Quan report quantity LST
INTRARATHOCOM
M
MOD
INTRARATHOCOM
Interfreq
InterFreqHoRprtInte M
IntraRatHoComm measurement eNodeB
rval LST
report interval
INTRARATHOCOM
M
MOD
INTRARATHOCOM
InterFreq A1A2
InterFreqHoA1A2Tri M
IntraRatHoComm Measurement eNodeB
gQuan LST
trigger quantity
INTRARATHOCOM
M
MOD
INTRARATHOCOM
A1A2 Measurement
FreqPriInterFreqHo M
IntraRatHoComm trigger quantity of eNodeB
A1TrigQuan LST
Freq Priority
INTRARATHOCOM
M
MOD
FreqPrior INTRARATHOCOM
InterFreqHoA4Trig loadBased A4 M
Quan Measurement LST
trigger quantity INTRARATHOCOM
M
LST
CSFALLBACKHO
CSFallBackHo LocalCellId Local cell ID eNodeB
MOD
CSFALLBACKHO
MOD
CSFB Utran
CsfbHoUtranTimeT CSFALLBACKHO
CSFallBackHo EventB1 Time To eNodeB
oTrig LST
Trig
CSFALLBACKHO
MOD
CSFB Geran
CsfbHoGeranTimeT CSFALLBACKHO
oTrig LST
Trig
CSFALLBACKHO
MOD
CSFB CDMA
CsfbHoCdmaTimeT CSFALLBACKHO
oTrig LST
Trig
CSFALLBACKHO
MOD
CSFB UTRAN
CsfbHoUtranB1Thd CSFALLBACKHO
CSFallBackHo EventB1 RSCP eNodeB
Rscp LST
Trigger Threshold
CSFALLBACKHO
MOD
CSFB UTRAN
CsfbHoUtranB1Thd CSFALLBACKHO
CSFallBackHo EventB1 ECN0 eNodeB
Ecn0 LST
Trigger Threshold
CSFALLBACKHO
MOD
CSFB GERAN
CsfbHoGeranB1Th CSFALLBACKHO
CSFallBackHo EventB1 Trigger eNodeB
d LST
Threshold
CSFALLBACKHO
MOD
CSFB CDMA2000
CsfbHoCdmaB1Thd CSFALLBACKHO
CSFallBackHo EventB1 Trigger eNodeB
Ps LST
Threshold
CSFALLBACKHO
LST CELLACBAR
CellAcBar LocalCellId Local cell ID eNodeB
MOD CELLACBAR
AC barring
AcBarringInfoCfgIn MOD CELLACBAR
CellAcBar information eNodeB
d LST CELLACBAR
configure indicator
AcBarringForEmerg Emergency call MOD CELLACBAR

CellAcBar eNodeB
ency barring state LST CELLACBAR
AC barring for
AcBarringForMoDat MOD CELLACBAR
CellAcBar mobile data eNodeB
aCfgInd LST CELLACBAR
configure indicator
Access probability
AcBarringFactorFor MOD CELLACBAR
CellAcBar factor for originating eNodeB
Call LST CELLACBAR
call
Mean access
MOD CELLACBAR
CellAcBar AcBarTimeForCall barring time for eNodeB
LST CELLACBAR
originating call
AC11 barring state MOD CELLACBAR

CellAcBar AC11BarforCall eNodeB
for originating call LST CELLACBAR


AC barring for
AcBarringForMoSig MOD CELLACBAR
CellAcBar mobile signal eNodeB
CfgInd LST CELLACBAR
configure indicator
AcBarringFactorFor Access probability MOD CELLACBAR
CellAcBar eNodeB
Sig factor for signaling LST CELLACBAR
Mean access
MOD CELLACBAR
CellAcBar AcBarTimeForSig barring time for eNodeB
LST CELLACBAR
signaling
CellAcBar AC11BarForSig eNodeB
for signaling LST CELLACBAR

for signalling LST CELLACBAR

for signalling LST CELLACBAR
LST CELLACCESS
CellAccess LocalCellId Local cell ID eNodeB MOD
CELLACCESS
MOD
CellAccess CellBarred Cell barring state eNodeB CELLACCESS
LST CELLACCESS
MOD
Cell reserved for
CellAccess CellReservedExt eNodeB CELLACCESS
extension
LST CELLACCESS
Intra-frequency MOD
CellAccess IntraFreqResel reselection eNodeB CELLACCESS
indication LST CELLACCESS
MOD
Plmn Broadcast
CellAccess BroadcastMode eNodeB CELLACCESS
Mode
LST CELLACCESS
MOD
Plmn Round
CellAccess RoundPeriod eNodeB CELLACCESS
Broadcast Period
LST CELLACCESS
ADD CELLOP
DSP
CELLBROADCAST
CellOp LocalCellId Local cell ID eNodeB CNOPERATOR
LST CELLOP
MOD CELLOP
RMV CELLOP
ADD CELLOP
LST CELLOP
CellOp TrackingAreaId Tracking area ID eNodeB
MOD CELLOP
RMV CELLOP
ADD CELLOP
Cell reserved for
CellOp CellReservedForOp eNodeB MOD CELLOP
operator
LST CELLOP
ADD CELLOP
Operator uplink RB
CellOp OpUlRbUsedRatio eNodeB MOD CELLOP
used ratio
LST CELLOP
ADD CELLOP
Operator downlink
CellOp OpDlRbUsedRatio eNodeB MOD CELLOP
RB used ratio
LST CELLOP
DSP
BroadcastCnOperat Broadcast CN
CellOp eNodeB CELLBROADCAST
orId operator ID
CNOPERATOR
LST CELLRESEL
CellResel LocalCellId Local cell ID eNodeB
MOD CELLRESEL
Hysteresis value for MOD CELLRESEL
CellResel Qhyst eNodeB
ranking criteria LST CELLRESEL
Speed-dependent
SpeedDepReselCfg reselection MOD CELLRESEL
CellResel eNodeB
Ind parameter LST CELLRESEL
configure indicator
The duration for
evaluating criteria MOD CELLRESEL
CellResel TEvaluation eNodeB
to enter mobility LST CELLRESEL
states
The additional
duration for
MOD CELLRESEL
CellResel THystNormal evaluating criteria eNodeB
LST CELLRESEL
to enter normal
mobility state
The number of cell
NCellChangeMediu changes to enter MOD CELLRESEL
CellResel eNodeB
m medium mobility LST CELLRESEL
state
The number of cell
MOD CELLRESEL
CellResel NCellChangeHigh changes to enter eNodeB
LST CELLRESEL
high mobility state
Additional
hysteresis applied MOD CELLRESEL
CellResel QHystSfMedium eNodeB
in medium mobility LST CELLRESEL
state to q-Hyst
Additional
hysteresis applied MOD CELLRESEL
CellResel QHystSfHigh eNodeB
in high mobility LST CELLRESEL
state to q-Hyst
Threshold for
EUTRAN inter-
SNonIntraSearchCf MOD CELLRESEL
CellResel frequency and inter- eNodeB
gInd LST CELLRESEL
RAT measurements
configure indicator
Threshold for
EUTRAN inter- MOD CELLRESEL
CellResel SNonIntraSearch eNodeB
frequency and inter- LST CELLRESEL
RAT measurements
Serving frequency
MOD CELLRESEL
CellResel ThrshServLow lower priority eNodeB
LST CELLRESEL
threshold
Cell reselection MOD CELLRESEL

CellResel CellReselPriority eNodeB
priority LST CELLRESEL
Minimum required MOD CELLRESEL
CellResel QRxLevMin eNodeB
RX level LST CELLRESEL
Ue max power
MOD CELLRESEL
CellResel PMaxCfgInd allowed configure eNodeB
LST CELLRESEL
indicator
Max transmit power MOD CELLRESEL

CellResel PMax eNodeB
allowed LST CELLRESEL
Threshold for intra
frequency MOD CELLRESEL
CellResel SIntraSearchCfgInd eNodeB
measurements LST CELLRESEL
configure indicator
Threshold for intra

MOD CELLRESEL
CellResel SIntraSearch frequency eNodeB
LST CELLRESEL
measurements
Measurement
MeasBandWidthCfg MOD CELLRESEL
CellResel bandwidth eNodeB
Ind LST CELLRESEL
configure indicator
Measurement MOD CELLRESEL
CellResel MeasBandWidth eNodeB
bandwidth LST CELLRESEL
Cell reselection
MOD CELLRESEL
CellResel TReselEutran timer value for eNodeB
LST CELLRESEL
EUTRAN
Speed state scale
SpeedStateSfCfgIn MOD CELLRESEL
CellResel factor configure eNodeB
d LST CELLRESEL
indicator
Scaling factor of
TReselEutranSfMe TReselEutra in MOD CELLRESEL
CellResel eNodeB
dium medium mobility LST CELLRESEL
state
Scaling factor of
TReselEutranSfHig MOD CELLRESEL
CellResel TReselEutra in high eNodeB
h LST CELLRESEL
mobility state
MOD CELLRESEL
CellResel NeighCellConfig Neighbor cell config eNodeB
LST CELLRESEL
PresenceAntennaP Presence antenna MOD CELLRESEL

CellResel eNodeB
ort1 port1 LST CELLRESEL
RSRQ Threshold
MOD CELLRESEL
CellResel SIntraSearchQ for intra frequency eNodeB
LST CELLRESEL
measurements
RSRQ Threshold
for EUTRAN inter- MOD CELLRESEL
CellResel SNonIntraSearchQ eNodeB
frequency and inter- LST CELLRESEL
RAT measurements
Serving frequency
ThrshServLowQCfg lower priority RSRQ MOD CELLRESEL
CellResel eNodeB
Ind threshold configure LST CELLRESEL
indicator
Serving frequency
MOD CELLRESEL
CellResel ThrshServLowQ lower priority RSRQ eNodeB
LST CELLRESEL
threshold
Minimum intra-
frequency
MOD CELLRESEL
CellResel QQualMinCfgInd reselection required eNodeB
LST CELLRESEL
quality level
configure indicator
Minimum intra-
frequency MOD CELLRESEL
CellResel QQualMin eNodeB
reselection required LST CELLRESEL
quality level
ADD
CELLRESELCDMA
2000
LST
CELLRESELCDMA
2000
CellReselCdma2000 LocalCellId Local cell ID eNodeB
MOD
CELLRESELCDMA
2000
RMV
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
System time MOD
CellReselCdma2000 SysTimeCfgInd information eNodeB CELLRESELCDMA
configure indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
CDMA and EUTRA
MOD
network
CellReselCdma2000 CdmaEutraSyn eNodeB CELLRESELCDMA
synchronised
2000
indicator
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
CDMA search MOD
SearchWndSizeCfg
CellReselCdma2000 window size eNodeB CELLRESELCDMA
Ind
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
CellReselCdma2000 SearchWndSize Search window size eNodeB CELLRESELCDMA
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
HRPD parameters
CellReselCdma2000 HrpdParamCfgInd eNodeB CELLRESELCDMA
configure indicator
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
HRPD cell MOD
HrpdCellReselectP
CellReselCdma2000 reselection eNodeB CELLRESELCDMA
aramCfgInd
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
HrpdPreRegistAllow HRPD pre-regist
CellReselCdma2000 eNodeB CELLRESELCDMA
ed allowed indicator
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
HrpdPreRegistZone HRPD pre-regist
Id zone ID
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
HRPD second pre- MOD
HrpdSecondPreRe
CellReselCdma2000 regist zone 0 eNodeB CELLRESELCDMA
gistZoneId0Ind
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
HrpdSecPreRegistZ HRPD secondary
oneId0 pre-regist zone ID 0
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
HRPD second pre- MOD
HrpdSecondPreRe
CellReselCdma2000 regist zone 1 eNodeB CELLRESELCDMA
gistZoneId1Ind
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
HrpdSecPreRegistZ HRPD secondary
oneId1 pre-regist zone ID 1
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cell reselection
CellReselCdma2000 TreselectionHrpd eNodeB CELLRESELCDMA
timer for HRPD
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
Speed state scale MOD
SpeedStateSfCfgIn
CellReselCdma2000 factor configure eNodeB CELLRESELCDMA
d
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
Scaling factor of
MOD
TReselCdmaHrpdSf TReselCdmaHrpd
High in high mobility
2000
state
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
Scaling factor of
MOD
TReselCdmaHrpdSf TReselCdmaHrpd
Medium in medium mobility
2000
state
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
1XRTT parameters
CellReselCdma2000 Cdma1XrttCfgInd eNodeB CELLRESELCDMA
configure indicator
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT csfb-
MOD
Cdma1XrttCsfbReg registration
CfgInd parameters
2000
configure indicator
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttCsfbReg
CellReselCdma2000 1XRTT system ID eNodeB CELLRESELCDMA
Sid
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttCsfbReg
CellReselCdma2000 1XRTT network ID eNodeB CELLRESELCDMA
Nid
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT multiple MOD
Cdma1XrttCsfbReg
CellReselCdma2000 system ID storage eNodeB CELLRESELCDMA
MultiSidInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT multiple MOD
Cdma1XrttCsfbReg
CellReselCdma2000 network ID storage eNodeB CELLRESELCDMA
MultiNidInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT home MOD
Cdma1XrttCsfbReg
CellReselCdma2000 registration eNodeB CELLRESELCDMA
HomeRegInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT system ID MOD
Cdma1XrttCsfbReg
CellReselCdma2000 roamer registration eNodeB CELLRESELCDMA
FrgnSidRegInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT network ID MOD
Cdma1XrttCsfbReg
CellReselCdma2000 roamer registration eNodeB CELLRESELCDMA
FrgnNidRegInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT parameter MOD
Cdma1XrttCsfbReg
CellReselCdma2000 change registration eNodeB CELLRESELCDMA
ParamRegInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT power up MOD
Cdma1XrttCsfbReg
CellReselCdma2000 registration eNodeB CELLRESELCDMA
PowerUpRegInd
indicator 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttCsfbReg 1XRTT registration
RegPeriod period
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttCsfbReg 1XRTT registration
RegZone zone
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT number of MOD
Cdma1XrttCsfbReg
CellReselCdma2000 registration zones eNodeB CELLRESELCDMA
TotalZone
to be retained 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttCsfbReg 1XRTT zone timer
ZoneTimer length
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT state of long
MOD
Cdma1XrttLongCod code generation
eStateCfgInd registers configure
2000
indicatorr
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT state of long MOD
Cdma1XrttLongCod
CellReselCdma2000 code generation eNodeB CELLRESELCDMA
eState
registers 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT cell MOD
Cdma1XrttCellRese
CellReselCdma2000 reselection eNodeB CELLRESELCDMA
lCfgInd
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttTreselect Cell reselection
ion timer for 1XRTT
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT speed state MOD
Cdma1XrttSpeedSt
CellReselCdma2000 scale factors eNodeB CELLRESELCDMA
ateCfgInd
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
Cdma1XrttSfMediu 1XRTT medium
m speed scale factor
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
MOD
1XRTT high speed
CellReselCdma2000 Cdma1XrttSfHigh eNodeB CELLRESELCDMA
scale factor
2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT power-down
MOD
CsfbRegPwrDownR registration
egCfgInd indicator configure
2000
indicator
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
1XRTT AC barring MOD
CellReselCdma2000 CsfbAcBarCfgInd information eNodeB CELLRESELCDMA
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
Persistence value MOD
CellReselCdma2000 CsfbAcBar0to9 for access overload eNodeB CELLRESELCDMA
classes 0 to 9 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
CellReselCdma2000 CsfbAcBar10 for access overload eNodeB CELLRESELCDMA
class 10 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
class 11 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
class 12 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
class 13 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
class 14 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
2000
class 15 2000
LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
Persistence 2000
modifier for access MOD
CellReselCdma2000 CsfbAcBarMsg barring factor for eNodeB CELLRESELCDMA
message 2000
transmissions LST
CELLRESELCDMA
2000
ADD
CELLRESELCDMA
Persistence 2000
modifier for access MOD
CellReselCdma2000 CsfbAcBarReg barring factor for eNodeB CELLRESELCDMA
autonomous 2000
registrations LST
CELLRESELCDMA
2000
ADD
Persistence value CELLRESELCDMA
for emergency calls 2000
and emergency MOD
CellReselCdma2000 CsfbAcBarEmg message eNodeB CELLRESELCDMA
transmissions for 2000
access overload LST
classes 0 to 9 CELLRESELCDMA
2000
ADD
CELLRESELGERA
N
LST
CELLRESELGERA
N
CellReselGeran LocalCellId Local cell ID eNodeB
MOD
CELLRESELGERA
N
RMV
CELLRESELGERA
N
ADD
CELLRESELGERA
N
Cell reselection MOD
CellReselGeran TReselGeran timer value for eNodeB CELLRESELGERA
GERAN N
LST
CELLRESELGERA
N
ADD
CELLRESELGERA
N
SpeedStateSfCfgIn
CellReselGeran factor configure eNodeB CELLRESELGERA
d
indicator N
LST
CELLRESELGERA
N
ADD
CELLRESELGERA
N
Scaling factor of
MOD
TReselGeranSfMed TReselGeran in
CellReselGeran eNodeB CELLRESELGERA
ium medium mobility
N
state
LST
CELLRESELGERA
N
ADD
CELLRESELGERA
N
Scaling factor of MOD
CellReselGeran TReselGeranSfHigh TReselGeran in eNodeB CELLRESELGERA
high mobility state N
LST
CELLRESELGERA
N
CELLRESELUTRA
N
LST
CELLRESELUTRA
N
CellReselUtran LocalCellId Local cell ID eNodeB
MOD
CELLRESELUTRA
N
RMV
CELLRESELUTRA
ADD
CELLRESELUTRA
N
CellReselUtran TReselUtran timer value for eNodeB CELLRESELUTRA
UTRAN N
LST
CELLRESELUTRA
N
ADD
CELLRESELUTRA
N
SpeedStateSfCfgIn
CellReselUtran factor configure eNodeB CELLRESELUTRA
d
indicator N
LST
CELLRESELUTRA
N
ADD
CELLRESELUTRA
N
Scaling factor of
MOD
TReselUtranSfMedi TReselUtran in
CellReselUtran eNodeB CELLRESELUTRA
um medium mobility
N
state
LST
CELLRESELUTRA
N
ADD
CELLRESELUTRA
N
CellReselUtran TReselUtranSfHigh TReselUtran in high eNodeB CELLRESELUTRA
mobility state N
LST
CELLRESELUTRA
N
LST CELLSEL
CellSel LocalCellId Local cell ID eNodeB
MOD CELLSEL
Minimum required MOD CELLSEL
CellSel QRxLevMin eNodeB
RX level LST CELLSEL

CellSel QRxLevMinOffset eNodeB
RX level offset LST CELLSEL
CellSel QQualMin eNodeB
RX quality level LST CELLSEL
Minimum required
QQualMinOffsetCfg RX quality level MOD CELLSEL
CellSel eNodeB
Ind offset configure LST CELLSEL
indicator
Minimum required
MOD CELLSEL
CellSel QQualMinOffset RX quality level eNodeB
LST CELLSEL
offset
LST CELLSIMAP
CellSiMap LocalCellId Local cell ID eNodeB
MOD CELLSIMAP
SIB mapping SI MOD CELLSIMAP

CellSiMap SiMapSwitch eNodeB
algorithm switch LST CELLSIMAP
MOD CELLSIMAP
CellSiMap Sib2Period SIB2 period eNodeB
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
MOD CELLSIMAP
LST CELLSIMAP
ETWS PN message MOD CELLSIMAP

CellSiMap EtwsPnDuration eNodeB
duration time LST CELLSIMAP
EtwsSnOverlapPoli ETWS SN message MOD CELLSIMAP
CellSiMap eNodeB
cy overlap policy LST CELLSIMAP
EtwsPnOverlapPoli ETWS PN message MOD CELLSIMAP
CellSiMap eNodeB
cy overlap policy LST CELLSIMAP
LST
CELLULPCCOMM
CellUlpcComm LocalCellId Local cell ID eNodeB
MOD
CELLULPCCOMM
MOD
CELLULPCCOMM
CellUlpcComm PassLossCoeff Path loss coefficient eNodeB
LST
CELLULPCCOMM
MOD
CELLULPCCOMM
CellUlpcComm P0NominalPUCCH P0 nominal PUCCH eNodeB
LST
CELLULPCCOMM
MOD
CELLULPCCOMM
CellUlpcComm P0NominalPUSCH P0 nominal PUSCH eNodeB
LST
CELLULPCCOMM
MOD
DeltaFPUCCHForm DeltaF for PUCCH CELLULPCCOMM
CellUlpcComm eNodeB
at1 format 1 LST
CELLULPCCOMM
MOD
CellUlpcComm eNodeB
at1b format 1b LST
CELLULPCCOMM
MOD
CellUlpcComm eNodeB
at2 format 2 LST
CELLULPCCOMM
MOD
CellUlpcComm eNodeB
at2a format 2a LST
CELLULPCCOMM
MOD
CellUlpcComm eNodeB
at2b format 2b LST
CELLULPCCOMM
MOD
DeltaPreambleMsg Delta preamble CELLULPCCOMM
CellUlpcComm eNodeB
3 value for msg3 LST
CELLULPCCOMM
ADD
ENBCELLOPRSVD
PARA
LST
ENBCELLOPRSVD
PARA
eNBCellOpRsvdParaLocalCellId Local cell ID eNodeB
MOD
ENBCELLOPRSVD
PARA
RMV
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
LST
ENBCELLOPRSVD
PARA
eNBCellOpRsvdParaTrackingAreaId Tracking area ID eNodeB
MOD
ENBCELLOPRSVD
PARA
RMV
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved Switch
eNBCellOpRsvdParaRsvdSwPara0 eNodeB ENBCELLOPRSVD
Parameter 0
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved Switch
Parameter 1
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved Switch
Parameter 2
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
eNBCellOpRsvdParaRsvdPara2 eNodeB ENBCELLOPRSVD
Parameter 2
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 3
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 4
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 5
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 6
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 7
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 8
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 9
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 10
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 11
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 12
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 13
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 14
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 15
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 16
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 17
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 18
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 19
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 20
PARA
LST
ENBCELLOPRSVD
PARA
ADD
ENBCELLOPRSVD
PARA
MOD
Reserved
Parameter 21
PARA
LST
ENBCELLOPRSVD
PARA
LST TATIMER
TimeAlignmentTimer LocalCellId Local cell ID eNodeB
MOD TATIMER
TimeAlignmentTime Uplink time MOD TATIMER

TimeAlignmentTimer eNodeB
r alignment timer LST TATIMER
LST
UETIMERCONST
UeTimerConst LocalCellId Local cell ID eNodeB
MOD
UETIMERCONST
MOD
UETIMERCONST
UeTimerConst T300 Timer 300 eNodeB
LST
UETIMERCONST
MOD
UETIMERCONST
LST
UETIMERCONST
MOD
UETIMERCONST
LST
UETIMERCONST
MOD
UETIMERCONST
LST
UETIMERCONST
MOD
UETIMERCONST
UeTimerConst N311 Constant N311 eNodeB
LST
UETIMERCONST
MOD
UETIMERCONST
UeTimerConst N310 Constant N310 eNodeB
LST
UETIMERCONST
ACT CELL
ADD CELL
BLK CELL
DEA CELL
DSP CELL
LST CELL
MOD CELL
Cell LocalCellId Local cell ID eNodeB
RMV CELL
STR
CELLRFLOOPBAC
K
STR
CELLSELFTEST
UBL CELL
ADD CELL
Cell CellName Cell name eNodeB MOD CELL
LST CELL
ADD CELL
Cell SectorId Sector No. eNodeB MOD CELL
LST CELL
ADD CELL
Cell CsgInd Csg indicator eNodeB MOD CELL
LST CELL
ADD CELL
Uplink cyclic prefix
Cell UlCyclicPrefix eNodeB MOD CELL
length
LST CELL
ADD CELL
Downlink cyclic
Cell DlCyclicPrefix eNodeB MOD CELL
prefix length
LST CELL
ADD CELL
Cell FreqBand Frequency band eNodeB MOD CELL
LST CELL
ADD CELL
Uplink earfcn
Cell UlEarfcnCfgInd eNodeB MOD CELL
indication
LST CELL
ADD CELL
Cell UlEarfcn Uplink earfcn eNodeB MOD CELL
LST CELL
ADD CELL
Cell DlEarfcn Downlink earfcn eNodeB MOD CELL
LST CELL
ADD CELL
Cell UlBandWidth Uplink bandwidth eNodeB MOD CELL
LST CELL
ADD CELL
Cell DlBandWidth Downlink bandwidth eNodeB MOD CELL
LST CELL
ADD CELL
Cell CellId Cell ID eNodeB MOD CELL
LST CELL
ADD CELL
Cell PhyCellId Physical cell ID eNodeB MOD CELL
LST CELL
ADD CELL
AdditionalSpectrum Additional spectrum
Cell eNodeB MOD CELL
Emission emission
LST CELL
Cell CellActiveState Cell active state eNodeB LST CELL

BLK CELL
Cell CellAdminState Cell admin state eNodeB
LST CELL
Cell middle block BLK CELL

Cell CellMidBlkTimer eNodeB
timer LST CELL
ADD CELL
Cell FDD TDD
Cell FddTddInd eNodeB MOD CELL
indication
LST CELL
ADD CELL
SubframeAssignme Subframe
nt assignment
LST CELL
ADD CELL
SpecialSubframePa Special subframe
tterns patterns
LST CELL
ADD CELL
Cell CellSpecificOffset Cell specific offset eNodeB MOD CELL
LST CELL
ADD CELL
Intra frequency
Cell QoffsetFreq eNodeB MOD CELL
offset
LST CELL
ADD CELL
Root sequence
Cell RootSequenceIdx eNodeB MOD CELL
index
LST CELL
ADD CELL
Cell HighSpeedFlag High speed flag eNodeB MOD CELL
LST CELL
ADD CELL
Cell PreambleFmt Preamble format eNodeB MOD CELL
LST CELL
ADD CELL
Cell CellRadius Cell radius eNodeB MOD CELL
LST CELL
Customized ADD CELL
CustomizedBandWi
Cell bandwidth eNodeB MOD CELL
dthCfgInd
configure indicator LST CELL
ADD CELL
CustomizedULBand Customized uplink
Width bandwidth
LST CELL
ADD CELL
CustomizedDLBand Customized
Width downlink bandwidth
LST CELL
ADD CELL
EmergencyAreaIdC Emergency Area Id
fgInd indicator
LST CELL
ADD CELL
Cell EmergencyAreaId Emergency Area ID eNodeB MOD CELL
LST CELL
Ue max power ADD CELL

Cell UePowerMaxCfgInd allowed configure eNodeB MOD CELL
indicator LST CELL
ADD CELL
Max transmit power
Cell UePowerMax eNodeB MOD CELL
allowed
LST CELL
ADD CELL
Flag of Multi-RRU
Cell MultiRruCellFlag eNodeB MOD CELL
Cell
LST CELL
ADD CELL
Mode of Multi-RRU
Cell MultiRruCellMode eNodeB MOD CELL
Cell
LST CELL
ADD CELL
Cell CPRICompression CPRI Compression eNodeB MOD CELL
LST CELL
Cell CellState Cell instance state eNodeB DSP CELL
Reason For Latest
Cell CellLatestAvailState eNodeB DSP CELL
State Change
CellLatestSetupTim Cell latest setup

Cell eNodeB DSP CELL
e time
CellLatestSetupTyp Cell latest setup
e operate type
CellLatestRemoveT Cell latest remove

ime time
CellLatestRemoveT Cell latest remove
ype operate type
CellPowerSaveStat Cell power save
e state
Cell BbiSlot Bbi slot eNodeB DSP CELL

Cell CellTopoType Cell topo type eNodeB DSP CELL
Cell CabinetNo Cabinet number eNodeB DSP CELL
Cell SubrackNo Subrack number eNodeB DSP CELL
Cell SlotNo Slot number eNodeB DSP CELL
SymbolShutdownSt Symbol shutdown

ate state
Maximum transmit
Cell MaxTxPower eNodeB DSP CELL
power
LST CELLBF
CellBf LocalCellId Local cell ID eNodeB
MOD CELLBF
Beamforming
MOD CELLBF
CellBf MaxBfRankPara maximum number eNodeB
LST CELLBF
of layers
LST
CELLDLICICMCPA
RA
CellDLIcicMcPara LocalCellId Local cell ID eNodeB
MOD
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
Downlink ICIC
RA
CellDLIcicMcPara ReportInterval measurement eNodeB
LST
report interval
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
Downlink ICIC
RA
CellDLIcicMcPara MaxReportCellNum measurement max eNodeB
LST
report cell number
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
DownLink ICIC
RA
CellDLIcicMcPara ReportAmount measurement eNodeB
LST
report amount
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
DownLink ICIC
RA
CellDLIcicMcPara ReportQuantity measurement eNodeB
LST
report quantity
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
DownLink ICIC
RA
CellDLIcicMcPara TriggerQuantity measurement eNodeB
LST
trigger quantity
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
DownLink ICIC
RA
CellDLIcicMcPara Hysteresis measurement eNodeB
LST
hysteresis
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
DownLink ICIC
RA
CellDLIcicMcPara TimeToTrigger measurement time eNodeB
LST
to trigger
CELLDLICICMCPA
RA
MOD
CELLDLICICMCPA
Downlink ICIC A3 RA
CellDLIcicMcPara A3Offset eNodeB
offset LST
CELLDLICICMCPA
RA
LST
CELLLOWPOWER
CellLowPower LocalCellId Local cell ID eNodeB
MOD
CELLLOWPOWER
MOD
Low power
CELLLOWPOWER
CellLowPower LowPwrSwitch consumption mode eNodeB
LST
switch
CELLLOWPOWER
MOD
Low power
CELLLOWPOWER
CellLowPower LowPwrOrder consumption mode eNodeB
LST
order
CELLLOWPOWER
MOD
CELLLOWPOWER
CellLowPower StartTime Start time eNodeB
LST
CELLLOWPOWER
MOD
CELLLOWPOWER
CellLowPower StopTime Stop time eNodeB
LST
CELLLOWPOWER
MOD
CellUsedPwrReduc Cell used power CELLLOWPOWER
CellLowPower eNodeB
eTimeLen reduce time length LST
CELLLOWPOWER
MOD
Reference signal
RsPwrReduceTime CELLLOWPOWER
CellLowPower power reduce time eNodeB
Len LST
length
CELLLOWPOWER
MOD
RfShutDownTimeLe RF shutdown time CELLLOWPOWER
CellLowPower eNodeB
n length LST
CELLLOWPOWER
MOD
Cell used power CELLLOWPOWER
CellLowPower CellUsedPwrRatio eNodeB
ratio LST
CELLLOWPOWER
MOD
Reference signal CELLLOWPOWER
CellLowPower RsPwrAdjOffset eNodeB
power adjust offset LST
CELLLOWPOWER
Time length for MOD
entering the low CELLLOWPOWER
CellLowPower EnterTimeLen eNodeB
power consumption LST
mode CELLLOWPOWER
LST CELLMRO
CellMro LocalCellId Local cell ID eNodeB
MOD CELLMRO
CIO adjustment
MOD CELLMRO
CellMro CioAdjLimitCfgInd range configuration eNodeB
LST CELLMRO
indicator
CIO adjustment MOD CELLMRO
CellMro CioAdjUpperLimit eNodeB
upper limit LST CELLMRO
CIO adjustment MOD CELLMRO

CellMro CioAdjLowerLimit eNodeB
lower limit LST CELLMRO
LST CELLRACTHD
CellRacThd LocalCellId Local cell ID eNodeB MOD
CELLRACTHD
MOD
Gold service arp
CellRacThd GoldServiceArpThd eNodeB CELLRACTHD
threshold
LST CELLRACTHD
MOD
SilverServiceArpTh Silver service arp
CellRacThd eNodeB CELLRACTHD
d threshold
LST CELLRACTHD
MOD
QCI1 handover
CellRacThd Qci1HoThd eNodeB CELLRACTHD
admission threshold
LST CELLRACTHD
MOD
QCI2 handover
admission threshold
LST CELLRACTHD
MOD
QCI3 handover
admission threshold
LST CELLRACTHD
MOD
QCI4 handover
admission threshold
LST CELLRACTHD
Gold new service MOD
NewGoldServiceOff
CellRacThd admission threshold eNodeB CELLRACTHD
set
offset LST CELLRACTHD
Silver new service MOD
NewSilverServiceOf
fset
Bronze new service MOD
NewCopperService
Offset
MOD
QCI1 congest
CellRacThd Qci1CongThd eNodeB CELLRACTHD
threshold
LST CELLRACTHD
MOD
QCI2 congest
threshold
LST CELLRACTHD
MOD
QCI3 congest
threshold
LST CELLRACTHD
MOD
QCI4 congest
threshold
LST CELLRACTHD
Gold-level GBR
MOD
GoldGbrCongPropo service congest
rtion scheduler
LST CELLRACTHD
proportion
Silver-level GBR
MOD
SilverGbrCongProp service congest
ortion scheduler
LST CELLRACTHD
proportion
Bronze-level GBR
MOD
CopperGbrCongPro service congest
portion scheduler
LST CELLRACTHD
proportion
GBR used resource MOD
GbrRbUsedHighTh
CellRacThd high proportion eNodeB CELLRACTHD
d
threshold LST CELLRACTHD
GBR used resource MOD

CellRacThd GbrRbUsedLowThd low proportion eNodeB CELLRACTHD
threshold LST CELLRACTHD
MOD
CellRacThd LdcMeaArpThd ARP threshold eNodeB CELLRACTHD
LST CELLRACTHD
MOD
Offset for service
CellRacThd CongRelOffset eNodeB CELLRACTHD
congest relieving
LST CELLRACTHD
MOD
Preemption ARP
CellRacThd PreemptionArpThd eNodeB CELLRACTHD
threshold
LST CELLRACTHD
MOD
Uplink RB used
CellRacThd UlRbHighThd eNodeB CELLRACTHD
ratio high threshold
LST CELLRACTHD
MOD
Downlink RB used
CellRacThd DlRbHighThd eNodeB CELLRACTHD
ratio high threshold
LST CELLRACTHD
MOD
Uplink RB used
CellRacThd UlRbLowThd eNodeB CELLRACTHD
ratio low threshold
LST CELLRACTHD
MOD
Downlink RB used
CellRacThd DlRbLowThd eNodeB CELLRACTHD
ratio low threshold
LST CELLRACTHD
MOD
MaxNonGbrBearer Non-GBR max
Num bearer number
LST CELLRACTHD
LST
CELLRFSHUTDO
WN
CellRfShutdown LocalCellId Local cell ID eNodeB
MOD
CELLRFSHUTDO
WN
MOD
CELLRFSHUTDO
RF intelligent WN
CellRfShutdown RfShutdownSwitch eNodeB
shutdown switch LST
CELLRFSHUTDO
WN
MOD
CELLRFSHUTDO
WN
CellRfShutdown StartTime Start time eNodeB
LST
CELLRFSHUTDO
WN
MOD
CELLRFSHUTDO
WN
CellRfShutdown StopTime Stop time eNodeB
LST
CELLRFSHUTDO
WN
MOD
CELLRFSHUTDO
Reference signal WN
CellRfShutdown RsPwrAdjOffset eNodeB
power adjust offset LST
CELLRFSHUTDO
WN
GET
CELLRICDATA
LST
CELLRICALGO
CellRicAlgo LocalCellId Local cell ID eNodeB
MOD
CELLRICALGO
SND
CELLRICPCISEQ
MOD
RIC algorithm CELLRICALGO
CellRicAlgo RicAlgoSwitch eNodeB
switch LST
CELLRICALGO
MOD
MuteUpPTSSymNu Mute UpPTS CELLRICALGO
CellRicAlgo eNodeB
m Symbol Number LST
CELLRICALGO
MOD
Whether to mute UL CELLRICALGO
CellRicAlgo MuteULSym eNodeB
symbol LST
CELLRICALGO
LST
CELLSHUTDOWN
CellShutdown LocalCellId Local cell ID eNodeB
MOD
CELLSHUTDOWN
MOD
CellShutdownSwitc Cell intelligent CELLSHUTDOWN
CellShutdown eNodeB
h shutdown switch LST
CELLSHUTDOWN
MOD
CELLSHUTDOWN
CellShutdown StartTime Start time eNodeB
LST
CELLSHUTDOWN
MOD
CELLSHUTDOWN
CellShutdown StopTime Stop time eNodeB
LST
CELLSHUTDOWN
MOD
Downlink PRB CELLSHUTDOWN
CellShutdown DlPrbThd eNodeB
threshold LST
CELLSHUTDOWN
MOD
Downlink PRB CELLSHUTDOWN
CellShutdown DlPrbOffset eNodeB
offset LST
CELLSHUTDOWN
MOD
Uplink PRB CELLSHUTDOWN
CellShutdown UlPrbThd eNodeB
threshold LST
CELLSHUTDOWN
MOD
CELLSHUTDOWN
CellShutdown UlPrbOffset Uplink PRB offset eNodeB
LST
CELLSHUTDOWN
LST
CELLULICICMCPA
RA
CellULIcicMcPara LocalCellId Local cell ID eNodeB
MOD
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara ReportInterval measurement eNodeB
LST
report interval
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara MaxReportCellNum measurement max eNodeB
LST
report cell number
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara ReportAmount measurement eNodeB
LST
report amount
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara ReportQuantity measurement eNodeB
LST
report quantity
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara TriggerQuantity measurement eNodeB
LST
trigger quantity
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara Hysteresis measurement eNodeB
LST
hysteresis
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC
RA
CellULIcicMcPara TimeToTrigger measurement time eNodeB
LST
to trigger
CELLULICICMCPA
RA
MOD
CELLULICICMCPA
Uplink ICIC A3 RA
CellULIcicMcPara A3Offset eNodeB
offset LST
CELLULICICMCPA
RA
LST
CELLULSCHALGO
CellUlschAlgo LocalCellId Local cell ID eNodeB
MOD
CELLULSCHALGO
MOD
Uplink Scheduling CELLULSCHALGO
CellUlschAlgo UlschStrategy eNodeB
Strategy LST
CELLULSCHALGO
MOD
adaptive HARQ CELLULSCHALGO
CellUlschAlgo AdaptHarqSwitch eNodeB
switch LST
CELLULSCHALGO
MOD
SinrAdjustTargetIble SINR target IBLER CELLULSCHALGO
CellUlschAlgo eNodeB
r adjustment LST
CELLULSCHALGO
System Bandwidth MOD

PreAllocationBand Ratio Used By Pre- CELLULSCHALGO
widthRatio schedule user per LST
TTI CELLULSCHALGO
MOD
PreAllocationMinPe minimal period of CELLULSCHALGO
riod pre-allocation LST
CELLULSCHALGO
MOD
data size of pre- CELLULSCHALGO
CellUlschAlgo PreAllocationSize eNodeB
allocation LST
CELLULSCHALGO
MOD
CELLULSCHALGO
CellUlschAlgo UlHoppingType Uplink hopping type eNodeB
LST
CELLULSCHALGO
MOD
FreeUserUlRbUsed Free Users Uplink CELLULSCHALGO
Ratio RB Ratio LST
CELLULSCHALGO
MOD
UL scheduling
CELLULSCHALGO
CellUlschAlgo UlSrSchDateLen request user data eNodeB
LST
length
CELLULSCHALGO
MOD
Semi-persistent
CELLULSCHALGO
CellUlschAlgo SpsRelThd resource implicit eNodeB
LST
release threshold
CELLULSCHALGO
ADD
ENBCELLRSVDPA
RA
LST
ENBCELLRSVDPA
RA
eNBCellRsvdPara LocalCellId Local cell ID eNodeB
MOD
ENBCELLRSVDPA
RA
RMV
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved Switch
eNBCellRsvdPara RsvdSwPara0 eNodeB ENBCELLRSVDPA
Parameter 0
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved Switch
Parameter 1
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved Switch
Parameter 2
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
eNBCellRsvdPara RsvdPara2 eNodeB ENBCELLRSVDPA
Parameter 2
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 3
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 4
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 5
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 6
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 7
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 8
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 9
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 10
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 11
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 12
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 13
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 14
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 15
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 16
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 17
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 18
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 19
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 20
RA
LST
ENBCELLRSVDPA
RA
ADD
ENBCELLRSVDPA
RA
MOD
Reserved
Parameter 21
RA
LST
ENBCELLRSVDPA
RA
LST
INTERRATCELLSH
UTDOWN
InterRatCellShutdow LocalCellId Local cell ID eNodeB
MOD
INTERRATCELLSH
UTDOWN
MOD
INTERRATCELLSH
ForceShutdownSwit Force shutdown UTDOWN
InterRatCellShutdow eNodeB
ch switch LST
INTERRATCELLSH
UTDOWN
MOD
INTERRATCELLSH
UTDOWN
InterRatCellShutdow StartTime Start time eNodeB
LST
INTERRATCELLSH
UTDOWN
MOD
INTERRATCELLSH
UTDOWN
InterRatCellShutdow StopTime Stop time eNodeB
LST
INTERRATCELLSH
UTDOWN
MOD
INTERRATCELLSH
Bear number UTDOWN
InterRatCellShutdow BearNumThd eNodeB
threshold LST
INTERRATCELLSH
UTDOWN
MOD
INTERRATCELLSH
Downlink PRB UTDOWN
InterRatCellShutdow DlPrbThd eNodeB
threshold LST
INTERRATCELLSH
UTDOWN
MOD
INTERRATCELLSH
Uplink PRB UTDOWN
InterRatCellShutdow UlPrbThd eNodeB
threshold LST
INTERRATCELLSH
UTDOWN
LST
CELLALGOSWITC
H
CellAlgoSwitch LocalCellId Local cell ID eNodeB
MOD
CELLALGOSWITC
H
MOD
CELLALGOSWITC
RACH algorithm H
CellAlgoSwitch RachAlgoSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
SoundingRS H
CellAlgoSwitch SrsAlgoSwitch eNodeB
algorithm switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
PUCCH algorithm H
CellAlgoSwitch PucchAlgoSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
AQM algorithm H
CellAlgoSwitch AqmAlgoSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
CQI adjust H
CellAlgoSwitch CqiAdjAlgoSwitch eNodeB
CELLALGOSWITC
H
MOD
CELLALGOSWITC
RlfDetectAlgoSwitc RLF detection H
CellAlgoSwitch eNodeB
h algorithm switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Dynamic adjust
H
CellAlgoSwitch DynAdjVoltSwitch voltage algorithm eNodeB
LST
switch
CELLALGOSWITC
H
MOD
CELLALGOSWITC
RAC algorithm H
CellAlgoSwitch RacAlgoSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Load balancing H
CellAlgoSwitch MlbAlgoSwitch eNodeB
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Downlink power
H
CellAlgoSwitch DlPcAlgoSwitch control algorithm eNodeB
LST
switch
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Uplink power
H
CellAlgoSwitch UlPcAlgoSwitch control algorithm eNodeB
LST
switch
CELLALGOSWITC
H
MOD
CELLALGOSWITC
H
CellAlgoSwitch BfAlgoSwitch BF algorithm switch eNodeB
LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
H
CellAlgoSwitch DlSchSwitch DL schedule switch eNodeB
LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Uplink schedule H
CellAlgoSwitch UlSchSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
RanShareModeSwit RAN Sharing Mode H
CellAlgoSwitch eNodeB
ch Switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Based on
FreqPriorityHoSwitc H
CellAlgoSwitch Frequency Priority eNodeB
h LST
HO Switch
CELLALGOSWITC
H
MOD
CELLALGOSWITC
MUBF algorithm H
CellAlgoSwitch MuBfAlgoSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
Distance-based H
CellAlgoSwitch DistBasedHoSwitch eNodeB
Handover Switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
AcBar algorithms H
CellAlgoSwitch AcBarAlgoSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
UlCoMP algorithms H
CellAlgoSwitch UlCompSwitch eNodeB
switch LST
CELLALGOSWITC
H
MOD
CELLALGOSWITC
MRC/IRC H
CellAlgoSwitch MrcIrcAdptSwitch eNodeB
adaptation switch LST
CELLALGOSWITC
H
LST CELLDLICIC
CellDlIcic LocalCellId Local cell ID eNodeB
MOD CELLDLICIC
Downlink band MOD CELLDLICIC

CellDlIcic BandMode eNodeB
division scheme LST CELLDLICIC
LST
CELLDLPCPDCCH
CellDlpcPdcch LocalCellId Local cell ID eNodeB
MOD
CELLDLPCPDCCH
MOD
DCI power offset for CELLDLPCPDCCH
CellDlpcPdcch DediDciPwrOffset eNodeB
dedicated control LST
CELLDLPCPDCCH
LST
CELLDLPCPDSCH
CellDlpcPdsch LocalCellId Local cell ID eNodeB
MOD
CELLDLPCPDSCH
MOD
CELLDLPCPDSCH
CellDlpcPdsch CcuPa Center UE PA eNodeB
LST
CELLDLPCPDSCH
MOD
CELLDLPCPDSCH
CellDlpcPdsch CeuPa Edge UE PA eNodeB
LST
CELLDLPCPDSCH
LST
CELLDLPCPHICH
CellDlpcPhich LocalCellId Local cell ID eNodeB
MOD
CELLDLPCPHICH
MOD
Phich Pc Off Power CELLDLPCPHICH
CellDlpcPhich PwrOffset eNodeB
Offset LST
CELLDLPCPHICH
LST
CELLDLSCHALGO
CellDlschAlgo LocalCellId Local cell ID eNodeB
MOD
CELLDLSCHALGO
MOD
Downlink CELLDLSCHALGO
CellDlschAlgo DlschStrategy eNodeB
scheduling Strategy LST
CELLDLSCHALGO
MOD
FreeUserDlRbUsed Free Users CELLDLSCHALGO
CellDlschAlgo eNodeB
Ratio Downlink RB Ratio LST
CELLDLSCHALGO
MOD
CELLDLSCHALGO
CellDlschAlgo BtServiceWeight P2P Service Weight eNodeB
LST
CELLDLSCHALGO
MOD
Other Service CELLDLSCHALGO
CellDlschAlgo OtherServiceWeight eNodeB
Weight LST
CELLDLSCHALGO
MOD
maximum number CELLDLSCHALGO
CellDlschAlgo MaxMimoRankPara eNodeB
of MIMO layers LST
CELLDLSCHALGO
LST CELLMLB
CellMLB LocalCellId Local cell ID eNodeB
MOD CELLMLB
Intra-Frequency
Mobility Load MOD CELLMLB
CellMLB IntraFreqMlbThd eNodeB
Balancing LST CELLMLB
Threshold
Inter-Frequency
CellMLB InterFreqMlbThd eNodeB
Balancing LST CELLMLB
Threshold
Inter-RAT Mobility
MOD CELLMLB
CellMLB InterRatMlbThd Load Balancing eNodeB
LST CELLMLB
Threshold
LoadExchangePeri Load Information MOD CELLMLB
CellMLB eNodeB
od Exchange Period LST CELLMLB
MOD CELLMLB
CellMLB LoadOffset Load Offset eNodeB
LST CELLMLB
Load Difference MOD CELLMLB
CellMLB LoadDiffThd eNodeB
Threshold LST CELLMLB
Inter-RAT Mobility
InterRatMlbUeNum MOD CELLMLB
CellMLB Load Balancing UE eNodeB
Thd LST CELLMLB
Number Threshold
UTRAN Idle Mode

CellMLB InitValidPeriod eNodeB
Balancing Initial LST CELLMLB
Valid Period
LST
CELLPDCCHALGO
CellPdcchAlgo LocalCellId Local cell ID eNodeB
MOD
CELLPDCCHALGO
MOD
SignalCongregateL CELLPDCCHALGO
CellPdcchAlgo ComSigCongregLv eNodeB
evel LST
CELLPDCCHALGO
MOD
Cce Ratio Adjust CELLPDCCHALGO
CellPdcchAlgo CceRatioAdjSwitch eNodeB
Switch LST
CELLPDCCHALGO
MOD
PDCCH Initial CELLPDCCHALGO
CellPdcchAlgo InitPdcchSymNum eNodeB
Symbol Number LST
CELLPDCCHALGO
MOD
PDCCH Virtual CELLPDCCHALGO
CellPdcchAlgo VirtualLoadPro eNodeB
Loading Proportion LST
CELLPDCCHALGO
MOD
PDCCH Symbol
PdcchSymNumSwit CELLPDCCHALGO
CellPdcchAlgo Number Adjust eNodeB
ch LST
Switch
CELLPDCCHALGO
MOD
CELLPDCCHALGO
CellPdcchAlgo CceUseRatio CCE use ratio eNodeB
LST
CELLPDCCHALGO
MOD
PDCCH
PdcchAggLvlCLAdj CELLPDCCHALGO
CellPdcchAlgo Aggregation Level eNodeB
ustSwitch LST
CL Switch
CELLPDCCHALGO
LST
CELLPUCCHALGO
CellPucchAlgo LocalCellId Local cell ID eNodeB
MOD
CELLPUCCHALGO
MOD
SRI Low Load CELLPUCCHALGO
CellPucchAlgo SriLowLoadThd eNodeB
Threshold LST
CELLPUCCHALGO
LST
CELLNOACCESSA
LMPARA
CellNoAccessAlmPa LocalCellId Local cell ID eNodeB
MOD
CELLNOACCESSA
LMPARA
MOD
CELLNOACCESSA
NoAccessStartDete No access detect LMPARA
CellNoAccessAlmPa eNodeB
ctTime start time LST
CELLNOACCESSA
LMPARA
MOD
CELLNOACCESSA
NoAccessStopDete No access detect LMPARA
ctTime stop time LST
CELLNOACCESSA
LMPARA
MOD
CELLNOACCESSA
NoAccessDetectTi No access detect LMPARA
mer timer LST
CELLNOACCESSA
LMPARA
LST CELLULICIC
CellUlIcic LocalCellId Local cell ID eNodeB
MOD CELLULICIC
Uplink band division MOD CELLULICIC

CellUlIcic BandMode eNodeB
scheme LST CELLULICIC
ADD
CELLSIMULOAD
DSP
CELLSIMULOAD
LST
CellSimuLoad LocalCellId Local cell ID eNodeB
CELLSIMULOAD
MOD
CELLSIMULOAD
RMV
CELLSIMULOAD
ADD
CELLSIMULOAD
MOD
CellSimuLoad SimLoadCfgIndex Configure Index eNodeB
CELLSIMULOAD
LST
CELLSIMULOAD
ADD
CELLSIMULOAD
SimuLoadTransMo SimuLoad MOD
CellSimuLoad eNodeB
de transmission mode CELLSIMULOAD
LST
CELLSIMULOAD
SimuLoad allocated DSP
CellSimuLoad SimuLoadRbNum eNodeB
RB Number CELLSIMULOAD
Commercial service DSP

CellSimuLoad CommercRbNum eNodeB
RB number CELLSIMULOAD

CellSimuLoad SimuLoadPower eNodeB
power CELLSIMULOAD

CellSimuLoad CommercPower eNodeB
power CELLSIMULOAD

CellSimuLoad SimuLoadUserNum eNodeB
user Number CELLSIMULOAD

CellSimuLoad CommercUserNum eNodeB
user number CELLSIMULOAD
LST BCCHCFG
BcchCfg LocalCellId Local cell ID eNodeB
MOD BCCHCFG
Modification period MOD BCCHCFG

BcchCfg ModifyPeriodCoeff eNodeB
coefficient LST BCCHCFG
LST
CELLCHPWRCFG
CellChPwrCfg LocalCellId Local cell ID eNodeB
MOD
CELLCHPWRCFG
MOD
CELLCHPWRCFG
CellChPwrCfg PcfichPwr PCFICH power eNodeB
LST
CELLCHPWRCFG
MOD
CELLCHPWRCFG
CellChPwrCfg PbchPwr PBCH power eNodeB
LST
CELLCHPWRCFG
MOD
CELLCHPWRCFG
CellChPwrCfg SchPwr SCH power eNodeB
LST
CELLCHPWRCFG
MOD
CELLCHPWRCFG
CellChPwrCfg DbchPwr DBCH power eNodeB
LST
CELLCHPWRCFG
MOD
CELLCHPWRCFG
CellChPwrCfg PchPwr PCH power eNodeB
LST
CELLCHPWRCFG
MOD
Rach response CELLCHPWRCFG
CellChPwrCfg RaRspPwr eNodeB
power LST
CELLCHPWRCFG
MOD
CELLCHPWRCFG
CellChPwrCfg PrsPwr Prs power eNodeB
LST
CELLCHPWRCFG
LST PDSCHCFG
PDSCHCfg LocalCellId Local cell ID eNodeB
MOD PDSCHCFG
ReferenceSignalPw Reference signal MOD PDSCHCFG
PDSCHCfg eNodeB
r power LST PDSCHCFG
MOD PDSCHCFG
PDSCHCfg Pb PB eNodeB
LST PDSCHCFG
LST RACHCFG
RACHCfg LocalCellId Local cell ID eNodeB
MOD RACHCFG
MOD RACHCFG
RACHCfg PwrRampingStep Power ramping step eNodeB
LST RACHCFG
Preamble initial
PreambInitRcvTarg MOD RACHCFG
RACHCfg received target eNodeB
etPwr LST RACHCFG
power
MessageSizeGroup Message size of MOD RACHCFG
RACHCfg eNodeB
A select group A LST RACHCFG
PRACH Frequency MOD RACHCFG

RACHCfg PrachFreqOffset eNodeB
Offset LST RACHCFG
Indication of
PrachConfigIndexC MOD RACHCFG
RACHCfg PRACH eNodeB
fgInd LST RACHCFG
Configuration Index
PRACH MOD RACHCFG
RACHCfg PrachConfigIndex eNodeB
Configuration Index LST RACHCFG
DSP SRSCFG
SRSCfg LocalCellId Local cell ID eNodeB LST SRSCFG
MOD SRSCFG
SRS subframe MOD SRSCFG
SRSCfg SrsSubframeCfg eNodeB
configuration LST SRSCFG
SRS ACK/NACK
MOD SRSCFG
SRSCfg AnSrsSimuTrans simultaneous eNodeB
LST SRSCFG
transmission
SRS Configuration MOD SRSCFG
SRSCfg SrsCfgInd eNodeB
Indicator LST SRSCFG
TDD SRS MOD SRSCFG
SRSCfg TddSrsCfgMode eNodeB
Configuration Mode LST SRSCFG
CellSrsBandwidthCf Cell srs bandwidth

SRSCfg eNodeB DSP SRSCFG
g configuration
LST PHICHCFG
PHICHCfg LocalCellId Local cell ID eNodeB
MOD PHICHCFG
MOD PHICHCFG
PHICHCfg PhichDuration PHICH duration eNodeB
LST PHICHCFG
MOD PHICHCFG
PHICHCfg PhichResource PHICH resource eNodeB
LST PHICHCFG
LST PCCHCFG
PCCHCfg LocalCellId Local cell ID eNodeB
MOD PCCHCFG
Default paging MOD PCCHCFG
PCCHCfg DefaultPagingCycle eNodeB
cycle LST PCCHCFG
MOD PCCHCFG
PCCHCfg Nb NB eNodeB
LST PCCHCFG
LST PUSCHCFG
PUSCHCfg LocalCellId Local cell ID eNodeB
MOD PUSCHCFG
MOD PUSCHCFG
PUSCHCfg Nsb Subband number eNodeB
LST PUSCHCFG
MOD PUSCHCFG
PUSCHCfg HoppingMode Hopping mode eNodeB
LST PUSCHCFG
MOD PUSCHCFG
PUSCHCfg HoppingOffset Hopping offset eNodeB
LST PUSCHCFG
GroupHoppingEnab Group hopping MOD PUSCHCFG
PUSCHCfg eNodeB
led enabled LST PUSCHCFG
GroupAssignPUSC Group assignment MOD PUSCHCFG
PUSCHCfg eNodeB
H PUSCH LST PUSCHCFG
SeqHoppingEnable Sequence hopping MOD PUSCHCFG
PUSCHCfg eNodeB
d enabled LST PUSCHCFG
MOD PUSCHCFG
PUSCHCfg CyclicShift Cyclic shift eNodeB
LST PUSCHCFG
MOD PUSCHCFG
PUSCHCfg Qam64Enabled Qam64 enabled eNodeB
LST PUSCHCFG
LST PUCCHCFG
PUCCHCfg LocalCellId Local cell ID eNodeB
MOD PUCCHCFG
MOD PUCCHCFG
PUCCHCfg DeltaShift Delta shift eNodeB
LST PUCCHCFG
ACK/SRI Channel MOD PUCCHCFG

PUCCHCfg NaSriChNum eNodeB
Number LST PUCCHCFG
MOD PUCCHCFG
PUCCHCfg CqiRbNum CQI RB number eNodeB
LST PUCCHCFG
ADD
CDMA2000EXTER
NALCELLPLMN
LST
Cdma2000ExternalCeCellGlobalId Cell global ID eNodeB CDMA2000EXTER
NALCELLPLMN
RMV
CDMA2000EXTER
NALCELLPLMN
ADD
CDMA2000EXTER
NALCELLPLMN
LST
Share mobile
Cdma2000ExternalCeShareMcc eNodeB CDMA2000EXTER
country code
NALCELLPLMN
RMV
CDMA2000EXTER
NALCELLPLMN
ADD
CDMA2000EXTER
NALCELLPLMN
LST
Share mobile
Cdma2000ExternalCeShareMnc eNodeB CDMA2000EXTER
network code
NALCELLPLMN
RMV
CDMA2000EXTER
NALCELLPLMN
ADD
CDMA2000HRPDN
CELL
LST
CDMA2000HRPDN
CELL
Cdma2000HrpdNcellLocalCellId Local cell ID eNodeB
MOD
CDMA2000HRPDN
CELL
RMV
CDMA2000HRPDN
CELL
ADD
CDMA2000HRPDN
CELL
LST
CDMA2000HRPDN
CELL
Cdma2000HrpdNcellCellGlobalId Cell global ID eNodeB
MOD
CDMA2000HRPDN
CELL
RMV
CDMA2000HRPDN
CELL
ADD
CDMA2000HRPDN
CELL
MOD
No handover
Cdma2000HrpdNcellNoHoFlag eNodeB CDMA2000HRPDN
indicator
CELL
LST
CDMA2000HRPDN
CELL
ADD
CDMA2000HRPDN
CELL
MOD
Cdma2000HrpdNcellNoRmvFlag No remove indicator eNodeB CDMA2000HRPDN
CELL
LST
CDMA2000HRPDN
CELL
ADD
CDMA2000HRPDN
CELL
MOD
Blind handover
Cdma2000HrpdNcellBlindHoPriority eNodeB CDMA2000HRPDN
priority
CELL
LST
CDMA2000HRPDN
CELL
LST
Cdma2000HrpdNcellAnrFlag ANR flag eNodeB CDMA2000HRPDN
CELL
ADD
CDMA2000HRPDN
CELL
MOD
Cdma2000HrpdNcellLocalCellName Local cell name eNodeB CDMA2000HRPDN
CELL
LST
CDMA2000HRPDN
CELL
ADD
CDMA2000HRPDN
CELL
MOD
NeighbourCellNam Neighbour cell
Cdma2000HrpdNcell eNodeB CDMA2000HRPDN
e name
CELL
LST
CDMA2000HRPDN
CELL
ADD
CDMA2000NFREQ
LST
CDMA2000NFREQ
Cdma2000Nfreq LocalCellId Local cell ID eNodeB
MOD
CDMA2000NFREQ
RMV
CDMA2000NFREQ
ADD
CDMA2000NFREQ
LST
CDMA2000NFREQ
Cdma2000Nfreq BandClass Band class eNodeB
MOD
CDMA2000NFREQ
RMV
CDMA2000NFREQ
ADD
CDMA2000NFREQ
LST
CDMA2000NFREQ
Cdma2000Nfreq Frequency Frequency eNodeB
MOD
CDMA2000NFREQ
RMV
CDMA2000NFREQ
ADD
CDMA2000NFREQ
MOD
Cdma2000Nfreq OffsetFreq Frequency offset eNodeB
CDMA2000NFREQ
LST
CDMA2000NFREQ
ADD
CDMA2000NFREQ
SearchWindowSize Search window size MOD
Cdma2000Nfreq eNodeB
CfgInd configure indicator CDMA2000NFREQ
LST
CDMA2000NFREQ
ADD
CDMA2000NFREQ
MOD
Cdma2000Nfreq SearchWindowSize Search window size eNodeB
CDMA2000NFREQ
LST
CDMA2000NFREQ
ADD
EUTRANEXTERNA
LCELLPLMN
LST
Mobile country
EutranExternalCellP Mcc eNodeB EUTRANEXTERNA
code
LCELLPLMN
RMV
EUTRANEXTERNA
LCELLPLMN
ADD
EUTRANEXTERNA
LCELLPLMN
LST
Mobile network
EutranExternalCellP Mnc eNodeB EUTRANEXTERNA
code
LCELLPLMN
RMV
EUTRANEXTERNA
LCELLPLMN
ADD
EUTRANEXTERNA
LCELLPLMN
LST
EutranExternalCellP eNodeBId eNodeB ID eNodeB EUTRANEXTERNA
LCELLPLMN
RMV
EUTRANEXTERNA
LCELLPLMN
ADD
EUTRANEXTERNA
LCELLPLMN
LST
EutranExternalCellP CellId Cell ID eNodeB EUTRANEXTERNA
LCELLPLMN
RMV
EUTRANEXTERNA
LCELLPLMN
ADD
EUTRANEXTERNA
LCELLPLMN
LST
Share mobile
EutranExternalCellP ShareMcc eNodeB EUTRANEXTERNA
country code
LCELLPLMN
RMV
EUTRANEXTERNA
LCELLPLMN
ADD
EUTRANEXTERNA
LCELLPLMN
LST
Share mobile
EutranExternalCellP ShareMnc eNodeB EUTRANEXTERNA
network code
LCELLPLMN
RMV
EUTRANEXTERNA
LCELLPLMN
ADD
GERANEXTERNAL
CELLPLMN
LST
GeranExternalCellP GeranCellId GERAN cell ID eNodeB GERANEXTERNAL
CELLPLMN
RMV
GERANEXTERNAL
CELLPLMN
ADD
GERANEXTERNAL
CELLPLMN
LST
GeranExternalCellP Lac Location area code eNodeB GERANEXTERNAL
CELLPLMN
RMV
GERANEXTERNAL
CELLPLMN
ADD
GERANEXTERNAL
CELLPLMN
LST
Mobile country
GeranExternalCellP Mcc eNodeB GERANEXTERNAL
code
CELLPLMN
RMV
GERANEXTERNAL
CELLPLMN
ADD
GERANEXTERNAL
CELLPLMN
LST
Mobile network
GeranExternalCellP Mnc eNodeB GERANEXTERNAL
code
CELLPLMN
RMV
GERANEXTERNAL
CELLPLMN
ADD
GERANEXTERNAL
CELLPLMN
LST
Share mobile
GeranExternalCellP ShareMcc eNodeB GERANEXTERNAL
country code
CELLPLMN
RMV
GERANEXTERNAL
CELLPLMN
ADD
GERANEXTERNAL
CELLPLMN
LST
Share mobile
GeranExternalCellP ShareMnc eNodeB GERANEXTERNAL
network code
CELLPLMN
RMV
GERANEXTERNAL
CELLPLMN
ADD
UTRANEXTERNAL
CELLPLMN
LST
UtranExternalCellPl UtranCellId UTRAN cell ID eNodeB UTRANEXTERNAL
CELLPLMN
RMV
UTRANEXTERNAL
CELLPLMN
ADD
UTRANEXTERNAL
CELLPLMN
LST
Mobile country
UtranExternalCellPl Mcc eNodeB UTRANEXTERNAL
code
CELLPLMN
RMV
UTRANEXTERNAL
CELLPLMN
ADD
UTRANEXTERNAL
CELLPLMN
LST
Mobile network
UtranExternalCellPl Mnc eNodeB UTRANEXTERNAL
code
CELLPLMN
RMV
UTRANEXTERNAL
CELLPLMN
ADD
UTRANEXTERNAL
CELLPLMN
LST
Share mobile
UtranExternalCellPl ShareMcc eNodeB UTRANEXTERNAL
country code
CELLPLMN
RMV
UTRANEXTERNAL
CELLPLMN
ADD
UTRANEXTERNAL
CELLPLMN
LST
Share mobile
UtranExternalCellPl ShareMnc eNodeB UTRANEXTERNAL
network code
CELLPLMN
RMV
UTRANEXTERNAL
CELLPLMN
ADD
CDMA2000EXTER
NALCELL
LST
CDMA2000EXTER
NALCELL
Cdma2000ExternalCeCellGlobalId Cell global ID eNodeB
MOD
CDMA2000EXTER
NALCELL
RMV
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
Cdma2000ExternalCeBandClass Band class eNodeB CDMA2000EXTER
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
Cdma2000ExternalCeFrequency Frequency eNodeB CDMA2000EXTER
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
Cdma2000ExternalCePnOffset Physical cell ID eNodeB CDMA2000EXTER
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
CDMA2000
Cdma2000ExternalCeCdma2000Type eNodeB CDMA2000EXTER
neighbor cell type
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
Mobile country
Cdma2000ExternalCeMcc eNodeB CDMA2000EXTER
code
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
Mobile network
Cdma2000ExternalCeMnc eNodeB CDMA2000EXTER
code
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA2000EXTER
NALCELL
MOD
Cdma2000ExternalCeCellName Cell name eNodeB CDMA2000EXTER
NALCELL
LST
CDMA2000EXTER
NALCELL
ADD
CDMA20001XRTT
NCELL
LST
CDMA20001XRTT
NCELL
Cdma20001XRTTNceLocalCellId Local cell ID eNodeB
MOD
CDMA20001XRTT
NCELL
RMV
CDMA20001XRTT
NCELL
ADD
CDMA20001XRTT
NCELL
LST
CDMA20001XRTT
NCELL
Cdma20001XRTTNceCellGlobalId Cell global ID eNodeB
MOD
CDMA20001XRTT
NCELL
RMV
CDMA20001XRTT
NCELL
ADD
CDMA20001XRTT
NCELL
MOD
No handover
Cdma20001XRTTNceNoHoFlag eNodeB CDMA20001XRTT
indicator
NCELL
LST
CDMA20001XRTT
NCELL
ADD
CDMA20001XRTT
NCELL
MOD
Cdma20001XRTTNceNoRmvFlag No remove indicator eNodeB CDMA20001XRTT
NCELL
LST
CDMA20001XRTT
NCELL
ADD
CDMA20001XRTT
NCELL
MOD
Blind handover
Cdma20001XRTTNceBlindHoPriority eNodeB CDMA20001XRTT
priority
NCELL
LST
CDMA20001XRTT
NCELL
LST
Cdma20001XRTTNceAnrFlag ANR flag eNodeB CDMA20001XRTT
NCELL
ADD
CDMA20001XRTT
NCELL
MOD
Cdma20001XRTTNceLocalCellName Local cell name eNodeB CDMA20001XRTT
NCELL
LST
CDMA20001XRTT
NCELL
ADD
CDMA20001XRTT
NCELL
MOD
Cdma20001XRTTNce eNodeB CDMA20001XRTT
e name
NCELL
LST
CDMA20001XRTT
NCELL
ADD
CDMA2000BANDC
LASS
LST
CDMA2000BANDC
LASS
Cdma2000BandClas LocalCellId Local cell ID eNodeB
MOD
CDMA2000BANDC
LASS
RMV
CDMA2000BANDC
LASS
ADD
CDMA2000BANDC
LASS
LST
CDMA2000BANDC
LASS
Cdma2000BandClas BandClass Band class eNodeB
MOD
CDMA2000BANDC
LASS
RMV
CDMA2000BANDC
LASS
ADD
CDMA2000BANDC
LASS
MOD
Cell reselection
Cdma2000BandClas CellReselPriority eNodeB CDMA2000BANDC
priority
LASS
LST
CDMA2000BANDC
LASS
ADD
CDMA2000BANDC
LASS
MOD
High priority
Cdma2000BandClas ThreshXHigh eNodeB CDMA2000BANDC
threshold
LASS
LST
CDMA2000BANDC
LASS
ADD
CDMA2000BANDC
LASS
MOD
Lower priority
Cdma2000BandClas ThreshXLow eNodeB CDMA2000BANDC
threshold
LASS
LST
CDMA2000BANDC
LASS
ADD
GERANEXTERNAL
CELL
LST
GERANEXTERNAL
Mobile country CELL
GeranExternalCell Mcc eNodeB
code MOD
GERANEXTERNAL
CELL
RMV
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
LST
GERANEXTERNAL
Mobile network CELL
GeranExternalCell Mnc eNodeB
code MOD
GERANEXTERNAL
CELL
RMV
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
GeranExternalCell GeranCellId GERAN cell ID eNodeB
MOD
GERANEXTERNAL
CELL
RMV
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
GeranExternalCell Lac Location area code eNodeB
MOD
GERANEXTERNAL
CELL
RMV
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
Routing area code
GeranExternalCell RacCfgInd eNodeB GERANEXTERNAL
configure indicator
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
GeranExternalCell Rac Routing area code eNodeB GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
GeranExternalCell BandIndicator Band indicator eNodeB GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
GeranExternalCell GeranArfcn GERAN ARFCN eNodeB GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
NetworkColourCod
GeranExternalCell Network color code eNodeB GERANEXTERNAL
e
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
BaseStationColour Base station color
GeranExternalCell eNodeB GERANEXTERNAL
Code code
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
GeranExternalCell DtmInd DTM indication eNodeB GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
GeranExternalCell CellName Cell name eNodeB GERANEXTERNAL
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANEXTERNAL
CELL
MOD
CS and PS
GeranExternalCell CsPsHOInd eNodeB GERANEXTERNAL
handover indication
CELL
LST
GERANEXTERNAL
CELL
ADD
GERANNCELL
DSP
GERANRIMINFO
GeranNcell LocalCellId Local cell ID eNodeB LST GERANNCELL
MOD
GERANNCELL
RMV
GERANNCELL
ADD
GERANNCELL
LST GERANNCELL
MOD
Mobile country
GeranNcell Mcc eNodeB GERANNCELL
code
RMV
GERANNCELL
DSP
GERANRIMINFO
ADD
GERANNCELL
LST GERANNCELL
MOD
Mobile network
GeranNcell Mnc eNodeB GERANNCELL
code
RMV
GERANNCELL
DSP
GERANRIMINFO
ADD
GERANNCELL
LST GERANNCELL
MOD
GeranNcell Lac Location area code eNodeB GERANNCELL
RMV
GERANNCELL
DSP
GERANRIMINFO
ADD
GERANNCELL
LST GERANNCELL
MOD
GeranNcell GeranCellId GERAN cell ID eNodeB GERANNCELL
RMV
GERANNCELL
DSP
GERANRIMINFO
ADD
GERANNCELL
GeranNcell NoRmvFlag No remove indicator eNodeB MOD
GERANNCELL
LST GERANNCELL
ADD
GERANNCELL
No handover
GeranNcell NoHoFlag eNodeB MOD
indicator
GERANNCELL
LST GERANNCELL
ADD
GERANNCELL
Blind handover
GeranNcell BlindHoPriority eNodeB MOD
priority
GERANNCELL
LST GERANNCELL
GeranNcell AnrFlag ANR flag eNodeB LST GERANNCELL
ADD
GERANNCELL
GeranNcell LocalCellName Local cell name eNodeB MOD
GERANNCELL
LST GERANNCELL
ADD
GERANNCELL
GeranNcell eNodeB MOD
e name
GERANNCELL
LST GERANNCELL
DSP
GeranNcell eNodeBId eNodeB ID eNodeB
GERANRIMINFO
GRimBeginningTim DSP
GeranNcell Rim latest start time eNodeB
e GERANRIMINFO
GLastRimUpdating Rim latest update DSP

GeranNcell eNodeB
Time time GERANRIMINFO
ADD
GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
GeranNfreqGroup LocalCellId Local cell ID eNodeB
MOD
GERANNFREQGR
OUP
RMV
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
GeranNfreqGroup BcchGroupId BCCH group ID eNodeB
MOD
GERANNFREQGR
OUP
RMV
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
GeranNfreqGroup GeranVersion GERAN version eNodeB GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
GeranNfreqGroup StartingArfcn Starting ARFCN eNodeB GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
GeranNfreqGroup BandIndicator Band indicator eNodeB GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
CellReselPriorityCfg
GeranNfreqGroup priority configure eNodeB GERANNFREQGR
Ind
indicator OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
Cell reselection
GeranNfreqGroup CellReselPriority eNodeB GERANNFREQGR
priority
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
PMAX configure
GeranNfreqGroup PmaxGeranCfgInd eNodeB GERANNFREQGR
indicator
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
GeranNfreqGroup PmaxGeran PMAX eNodeB GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
Minimum required
GeranNfreqGroup QRxLevMin eNodeB GERANNFREQGR
RX level
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
High priority
GeranNfreqGroup ThreshXHigh eNodeB GERANNFREQGR
threshold
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
Lower priority
GeranNfreqGroup ThreshXLow eNodeB GERANNFREQGR
threshold
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
GeranNfreqGroup OffsetFreq Frequency offset eNodeB GERANNFREQGR
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUP
MOD
NCC monitoring
GeranNfreqGroup NccPermitted eNodeB GERANNFREQGR
permitted
OUP
LST
GERANNFREQGR
OUP
ADD
GERANNFREQGR
OUPARFCN
LST
GeranNfreqGroupArfLocalCellId Local cell ID eNodeB GERANNFREQGR
OUPARFCN
RMV
GERANNFREQGR
OUPARFCN
ADD
GERANNFREQGR
OUPARFCN
LST
GeranNfreqGroupArfBcchGroupId BCCH group ID eNodeB GERANNFREQGR
OUPARFCN
RMV
GERANNFREQGR
OUPARFCN
ADD
GERANNFREQGR
OUPARFCN
LST
GeranNfreqGroupArfGeranArfcn GERAN ARFCN eNodeB GERANNFREQGR
OUPARFCN
RMV
GERANNFREQGR
OUPARFCN
ADD
INTRAFREQBLKC
ELL
LST
INTRAFREQBLKC
ELL
IntraFreqBlkCell LocalCellId Local cell ID eNodeB
MOD
INTRAFREQBLKC
ELL
RMV
INTRAFREQBLKC
ELL
ADD
INTRAFREQBLKC
ELL
LST
INTRAFREQBLKC
Start physical cell ELL
IntraFreqBlkCell PhyCellId eNodeB
ID MOD
INTRAFREQBLKC
ELL
RMV
INTRAFREQBLKC
ELL
ADD
INTRAFREQBLKC
ELL
MOD
IntraFreqBlkCell CellName Cell name eNodeB INTRAFREQBLKC
ELL
LST
INTRAFREQBLKC
ELL
ADD
INTRAFREQBLKC
ELL
MOD
Physical cell ID
IntraFreqBlkCell PhyCellIdRange eNodeB INTRAFREQBLKC
range
ELL
LST
INTRAFREQBLKC
ELL
ADD
EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
EutranIntraFreqNCel LocalCellId Local cell ID eNodeB
MOD
EUTRANINTRAFR
EQNCELL
RMV
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
Mobile country EQNCELL
EutranIntraFreqNCel Mcc eNodeB
code MOD
EUTRANINTRAFR
EQNCELL
RMV
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
Mobile network EQNCELL
EutranIntraFreqNCel Mnc eNodeB
code MOD
EUTRANINTRAFR
EQNCELL
RMV
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
EutranIntraFreqNCel eNodeBId eNodeB ID eNodeB
MOD
EUTRANINTRAFR
EQNCELL
RMV
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
EutranIntraFreqNCel CellId Cell ID eNodeB
MOD
EUTRANINTRAFR
EQNCELL
RMV
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
MOD
EutranIntraFreqNCel CellIndividualOffset Cell individual offset eNodeB EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
MOD
EutranIntraFreqNCel CellQoffset Cell offset eNodeB EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
MOD
No handover
EutranIntraFreqNCel NoHoFlag eNodeB EUTRANINTRAFR
indicator
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
MOD
EutranIntraFreqNCel NoRmvFlag No remove indicator eNodeB EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
LST
EutranIntraFreqNCel AnrFlag ANR flag eNodeB EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
MOD
EutranIntraFreqNCel LocalCellName Local cell name eNodeB EUTRANINTRAFR
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTRAFR
EQNCELL
MOD
EutranIntraFreqNCel eNodeB EUTRANINTRAFR
e name
EQNCELL
LST
EUTRANINTRAFR
EQNCELL
ADD
EUTRANINTERNF
REQ
LST
EUTRANINTERNF
REQ
EutranInterNFreq LocalCellId Local cell ID eNodeB
MOD
EUTRANINTERNF
REQ
RMV
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
LST
EUTRANINTERNF
REQ
EutranInterNFreq DlEarfcn Downlink EARFCN eNodeB
MOD
EUTRANINTERNF
REQ
RMV
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
Uplink EARFCN
EutranInterNFreq UlEarfcnCfgInd eNodeB EUTRANINTERNF
configure indicator
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
EutranInterNFreq UlEarfcn Uplink EARFCN eNodeB EUTRANINTERNF
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Inter frequency cell MOD
EutranInterNFreq resel priority eNodeB EUTRANINTERNF
Ind
configure indicator REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
Inter frequency cell
EutranInterNFreq CellReselPriority eNodeB EUTRANINTERNF
resel priority
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
EUTRAN
EutranInterNFreq EutranReselTime eNodeB EUTRANINTERNF
reselection time
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Speed dependent
MOD
SpeedDependSPCf resel parameter
EutranInterNFreq eNodeB EUTRANINTERNF
gInd configuring
REQ
indicator
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Scaling factor of
MOD
TReselEutranSfMe treseleutra in
dium medium mobility
REQ
state
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
TReselEutranSfHig
EutranInterNFreq treseleutra in high eNodeB EUTRANINTERNF
h
mobility state REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
Measurement
EutranInterNFreq MeasBandWidth eNodeB EUTRANINTERNF
bandwidth
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
EutranInterNFreq QoffsetFreq Frequency offset eNodeB EUTRANINTERNF
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
Inter frequency high
EutranInterNFreq ThreshXhigh eNodeB EUTRANINTERNF
priority threshold
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Inter frequency MOD
EutranInterNFreq ThreshXlow lower priority eNodeB EUTRANINTERNF
threshold REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
Minimum required
EutranInterNFreq QRxLevMin eNodeB EUTRANINTERNF
RX level
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
PMAX configure
EutranInterNFreq PmaxCfgInd eNodeB EUTRANINTERNF
indicator
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
EutranInterNFreq Pmax PMAX eNodeB EUTRANINTERNF
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
EutranInterNFreq NeighCellConfig Neighbor cell config eNodeB EUTRANINTERNF
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
PresenceAntennaP Presence antenna
ort1 port1
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
InterFreqHoEventTy Inter-Freq HO
pe trigger Event Type
REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Inter frequency high MOD
EutranInterNFreq ThreshXhighQ priority RSRQ eNodeB EUTRANINTERNF
threshold REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Inter frequency low MOD
EutranInterNFreq ThreshXlowQ priority RSRQ eNodeB EUTRANINTERNF
threshold REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
Minimum RX signal MOD
EutranInterNFreq QqualMinCfgInd quality configuration eNodeB EUTRANINTERNF
indicator REQ
LST
EUTRANINTERNF
REQ
ADD
EUTRANINTERNF
REQ
MOD
Minimum RX signal
EutranInterNFreq QqualMin eNodeB EUTRANINTERNF
quality
REQ
LST
EUTRANINTERNF
REQ
ADD
INTERFREQBLKC
ELL
LST
INTERFREQBLKC
ELL
InterFreqBlkCell LocalCellId Local cell ID eNodeB
MOD
INTERFREQBLKC
ELL
RMV
INTERFREQBLKC
ELL
ADD
INTERFREQBLKC
ELL
LST
INTERFREQBLKC
ELL
InterFreqBlkCell DlEarfcn Downlink EARFCN eNodeB
MOD
INTERFREQBLKC
ELL
RMV
INTERFREQBLKC
ELL
ADD
INTERFREQBLKC
ELL
LST
INTERFREQBLKC
Start physical cell ELL
InterFreqBlkCell PhyCellId eNodeB
ID MOD
INTERFREQBLKC
ELL
RMV
INTERFREQBLKC
ELL
ADD
INTERFREQBLKC
ELL
MOD
InterFreqBlkCell CellName Cell name eNodeB INTERFREQBLKC
ELL
LST
INTERFREQBLKC
ELL
ADD
INTERFREQBLKC
ELL
MOD
Physical cell ID
InterFreqBlkCell PhyCellIdRange eNodeB INTERFREQBLKC
range
ELL
LST
INTERFREQBLKC
ELL
ADD
EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
EutranInterFreqNCel LocalCellId Local cell ID eNodeB
MOD
EUTRANINTERFR
EQNCELL
RMV
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
Mobile country EQNCELL
EutranInterFreqNCel Mcc eNodeB
code MOD
EUTRANINTERFR
EQNCELL
RMV
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
Mobile network EQNCELL
EutranInterFreqNCel Mnc eNodeB
code MOD
EUTRANINTERFR
EQNCELL
RMV
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
EutranInterFreqNCel eNodeBId eNodeB ID eNodeB
MOD
EUTRANINTERFR
EQNCELL
RMV
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
EutranInterFreqNCel CellId Cell ID eNodeB
MOD
EUTRANINTERFR
EQNCELL
RMV
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
EutranInterFreqNCel CellIndividualOffset Cell individual offset eNodeB EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
EutranInterFreqNCel CellQoffset Cell offset eNodeB EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
No handover
EutranInterFreqNCel NoHoFlag eNodeB EUTRANINTERFR
indicator
EQNCELL
LST
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
EutranInterFreqNCel NoRmvFlag No remove indicator eNodeB EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
Blind handover
EutranInterFreqNCel BlindHoPriority eNodeB EUTRANINTERFR
Priority
EQNCELL
LST
EUTRANINTERFR
EQNCELL
LST
EutranInterFreqNCel AnrFlag ANR flag eNodeB EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
EutranInterFreqNCel LocalCellName Local cell name eNodeB EUTRANINTERFR
EQNCELL
LST
EUTRANINTERFR
EQNCELL
ADD
EUTRANINTERFR
EQNCELL
MOD
EutranInterFreqNCel eNodeB EUTRANINTERFR
e name
EQNCELL
LST
EUTRANINTERFR
EQNCELL
ADD
EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
Mobile country LCELL
EutranExternalCell Mcc eNodeB
code MOD
EUTRANEXTERNA
LCELL
RMV
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
Mobile network LCELL
EutranExternalCell Mnc eNodeB
code MOD
EUTRANEXTERNA
LCELL
RMV
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
EutranExternalCell eNodeBId eNodeB ID eNodeB
MOD
EUTRANEXTERNA
LCELL
RMV
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
EutranExternalCell CellId Cell ID eNodeB
MOD
EUTRANEXTERNA
LCELL
RMV
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
MOD
EutranExternalCell DlEarfcn Downlink EARFCN eNodeB EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
MOD
Uplink EARFCN
EutranExternalCell UlEarfcnCfgInd eNodeB EUTRANEXTERNA
indicator
LCELL
LST
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
MOD
EutranExternalCell UlEarfcn Uplink EARFCN eNodeB EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
MOD
EutranExternalCell PhyCellId Physical cell ID eNodeB EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
MOD
EutranExternalCell Tac Tracking area code eNodeB EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
ADD
EUTRANEXTERNA
LCELL
MOD
EutranExternalCell CellName Cell name eNodeB EUTRANEXTERNA
LCELL
LST
EUTRANEXTERNA
LCELL
GERANRANSHAR
E
LST
GERANRANSHAR
E
GeranRanShare LocalCellId Local cell ID eNodeB
MOD
GERANRANSHAR
E
RMV
GERANRANSHAR
GERANRANSHAR
E
LST
GERANRANSHAR
E
GeranRanShare BcchGroupId BCCH group ID eNodeB
MOD
GERANRANSHAR
E
RMV
GERANRANSHAR
ADD
GERANRANSHAR
E
LST
GERANRANSHAR
Mobile country E
GeranRanShare Mcc eNodeB
code MOD
GERANRANSHAR
E
RMV
GERANRANSHAR
E
ADD
GERANRANSHAR
E
LST
GERANRANSHAR
Mobile network E
GeranRanShare Mnc eNodeB
code MOD
GERANRANSHAR
E
RMV
GERANRANSHAR
E
ADD
GERANRANSHAR
E
GeranRanShare priority configure eNodeB GERANRANSHAR
Ind
indicator E
LST
GERANRANSHAR
E
ADD
GERANRANSHAR
E
MOD
Cell reselection
GeranRanShare CellReselPriority eNodeB GERANRANSHAR
priority
E
LST
GERANRANSHAR
E
UTRANNCELL
DSP
UTRANRIMINFO
UtranNCell LocalCellId Local cell ID eNodeB LST UTRANNCELL
MOD
UTRANNCELL
RMV
ADD
UTRANNCELL
LST UTRANNCELL
MOD
Mobile country
UtranNCell Mcc eNodeB UTRANNCELL
code
RMV
UTRANNCELL
DSP
UTRANRIMINFO
ADD
UTRANNCELL
LST UTRANNCELL
MOD
Mobile network
UtranNCell Mnc eNodeB UTRANNCELL
code
RMV
UTRANNCELL
DSP
UTRANRIMINFO
ADD
UTRANNCELL
LST UTRANNCELL
MOD
UtranNCell UtranCellId UTRAN cell ID eNodeB UTRANNCELL
RMV
UTRANNCELL
DSP
UTRANRIMINFO
ADD
UTRANNCELL
No handover
UtranNCell NoHoFlag eNodeB MOD
indicator
UTRANNCELL
LST UTRANNCELL
ADD
UTRANNCELL
UtranNCell NoRmvFlag No remove indicator eNodeB MOD
UTRANNCELL
LST UTRANNCELL
ADD
UTRANNCELL
Blind handover
UtranNCell BlindHoPriority eNodeB MOD
priority
UTRANNCELL
LST UTRANNCELL
UtranNCell AnrFlag ANR flag eNodeB LST UTRANNCELL

ADD
UTRANNCELL
UtranNCell LocalCellName Local cell name eNodeB MOD
UTRANNCELL
LST UTRANNCELL
ADD
UTRANNCELL
UtranNCell eNodeB MOD
e name
UTRANNCELL
LST UTRANNCELL
DSP
UtranNCell eNodeBId eNodeB ID eNodeB
UTRANRIMINFO
DSP
UtranNCell RncId RNC ID eNodeB
UTRANRIMINFO
URimBeginningTim DSP
UtranNCell Rim latest start time eNodeB
e UTRANRIMINFO
ULastRimUpdating RIM latest update DSP

UtranNCell eNodeB
Time time UTRANRIMINFO
UTRANRANSHAR
E
LST
UTRANRANSHAR
E
UtranRanShare LocalCellId Local cell ID eNodeB
MOD
UTRANRANSHAR
E
RMV
UTRANRANSHAR
ADD
UTRANRANSHAR
E
LST
UTRANRANSHAR
E
UtranRanShare UtranDlArfcn Downlink UARFCN eNodeB
MOD
UTRANRANSHAR
E
RMV
UTRANRANSHAR
E
ADD
UTRANRANSHAR
E
LST
UTRANRANSHAR
Mobile country E
UtranRanShare Mcc eNodeB
code MOD
UTRANRANSHAR
E
RMV
UTRANRANSHAR
E
ADD
UTRANRANSHAR
E
LST
UTRANRANSHAR
Mobile network E
UtranRanShare Mnc eNodeB
code MOD
UTRANRANSHAR
E
RMV
UTRANRANSHAR
E
ADD
UTRANRANSHAR
E
UtranRanShare priority configure eNodeB UTRANRANSHAR
Ind
indicator E
LST
UTRANRANSHAR
E
ADD
UTRANRANSHAR
E
MOD
Cell reselection
UtranRanShare CellReselPriority eNodeB UTRANRANSHAR
priority
E
LST
UTRANRANSHAR
E
ADD
UTRANNFREQ
LST
UTRANNFREQ
UtranNFreq LocalCellId Local cell ID eNodeB
MOD
UTRANNFREQ
RMV
UTRANNFREQ
ADD
UTRANNFREQ
LST
UTRANNFREQ
UtranNFreq UtranDlArfcn Downlink UARFCN eNodeB
MOD
UTRANNFREQ
RMV
UTRANNFREQ
ADD
UTRANNFREQ
MOD
UtranNFreq UtranVersion UTRAN version eNodeB
UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
UTRAN cell type MOD
UtranNFreq UtranFddTddType eNodeB
indicator UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
Uplink UARFCN MOD
UtranNFreq UtranUlArfcnCfgInd eNodeB
indicator UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
MOD
UtranNFreq UtranUlArfcn Uplink UARFCN eNodeB
UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
CellReselPriorityCfg Reselection priority MOD
UtranNFreq eNodeB
Ind configure indicator UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
UtranNFreq CellReselPriority eNodeB
priority UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
MOD
UtranNFreq PmaxUtran PMAX eNodeB
UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
MOD
UtranNFreq OffsetFreq Frequency offset eNodeB
UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
Minimum required MOD
UtranNFreq Qqualmin eNodeB
quality level UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
Minimum required MOD
UtranNFreq QRxLevMin eNodeB
RX level UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
UTRAN high priority MOD
UtranNFreq ThreshXHigh eNodeB
threshold UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
UTRAN lower MOD
UtranNFreq ThreshXLow eNodeB
priority threshold UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
UTRAN high priority MOD
UtranNFreq ThreshXHighQ eNodeB
RSRQ threshold UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
UTRAN low priority MOD
UtranNFreq ThreshXLowQ eNodeB
RSRQ threshold UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
MOD
UtranNFreq PsPriority PS service priority eNodeB
UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANNFREQ
MOD
UtranNFreq CsPriority CS service priority eNodeB
UTRANNFREQ
LST
UTRANNFREQ
ADD
UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
Mobile country CELL
UtranExternalCell Mcc eNodeB
code MOD
UTRANEXTERNAL
CELL
RMV
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
Mobile network CELL
UtranExternalCell Mnc eNodeB
code MOD
UTRANEXTERNAL
CELL
RMV
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
UtranExternalCell UtranCellId UTRAN cell ID eNodeB
MOD
UTRANEXTERNAL
CELL
RMV
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UTRAN cell type
UtranExternalCell UtranFddTddType eNodeB UTRANEXTERNAL
indicator
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UtranExternalCell UtranDlArfcn Downlink UARFCN eNodeB UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
Uplink UARFCN
UtranExternalCell UtranUlArfcnCfgInd eNodeB UTRANEXTERNAL
configure indicator
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UtranExternalCell UtranUlArfcn Uplink UARFCN eNodeB UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UtranExternalCell RncId RNC ID eNodeB UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
Routing area code
UtranExternalCell RacCfgInd eNodeB UTRANEXTERNAL
configure indicator
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UtranExternalCell Rac Routing area code eNodeB UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
Primary scrambling
UtranExternalCell PScrambCode eNodeB UTRANEXTERNAL
code
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UtranExternalCell Lac Location area code eNodeB UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
UtranExternalCell CellName Cell name eNodeB UTRANEXTERNAL
CELL
LST
UTRANEXTERNAL
CELL
ADD
UTRANEXTERNAL
CELL
MOD
CS and PS
UtranExternalCell CsPsHOInd eNodeB UTRANEXTERNAL
handover indicator
CELL
LST
UTRANEXTERNAL
CELL
ANR add cell MOD ANR
ANR AddCellThd eNodeB
threshold LST ANR
ANR delete cell MOD ANR
ANR DelCellThd eNodeB
threshold LST ANR
Least Handover MOD ANR

ANR NcellHoStatNum eNodeB
Num for Statistic LST ANR
MOD ANR
ANR StatisticPeriod Statistic cycle eNodeB
LST ANR
Fast ANR PCI MOD ANR

ANR FastAnrRprtAmount eNodeB
report amount LST ANR
Fast ANR PCI MOD ANR

ANR FastAnrRprtInterval eNodeB
report interval LST ANR
FastAnrCheckPerio Fast ANR checking MOD ANR

ANR eNodeB
d period LST ANR
Fast ANR
MOD ANR
ANR FastAnrRsrpThd measurement eNodeB
LST ANR
RSRP threshold
IntraRat Fast ANR
FastAnrIntraRatMe MOD ANR
ANR measurement UE eNodeB
asUeNum LST ANR
number
InterRat Fast ANR

FastAnrInterRatMe MOD ANR
ANR measurement UE eNodeB
asUeNum LST ANR
number
IntraRat Fast ANR

FastAnrIntraRatUe MOD ANR
ANR valid measurement eNodeB
NumThd LST ANR
min UE number
InterRat Fast ANR
FastAnrInterRatUe MOD ANR
ANR valid measurement eNodeB
NumThd LST ANR
min UE number
MOD ANR
ANR OptMode Optimization Mode eNodeB
LST ANR
StatisticPeriodForN Statistic Cycle For MOD ANR

ANR eNodeB
RTDel Delete NRT LST ANR
StatisticNumForNR Statistic Number MOD ANR
ANR eNodeB
TDel For Delete NRT LST ANR
ANR Active PCI

ActivePciConflictSw MOD ANR
ANR Conflict Detection eNodeB
itch LST ANR
Switch
MOD ANR
ANR StartTime Start time eNodeB
LST ANR
MOD ANR
ANR StopTime Stop time eNodeB
LST ANR
UTRAN Fast ANR MOD ANR

ANR FastAnrRscpThd eNodeB
RSCP threshold LST ANR
GERAN Fast ANR MOD ANR

ANR FastAnrRssiThd eNodeB
RSSI threshold LST ANR
CDMA2000 1XRTT
FastAnrCdma1xrttP MOD ANR
ANR Fast ANR Pilot eNodeB
ilotThd LST ANR
threshold
CDMA2000 HRPD
FastAnrCdmahrpdP MOD ANR
ANR Fast ANR Pilot eNodeB
ilotThd LST ANR
threshold
MOD
Period update CELLIDPRDUPT
CellIdPrdUpt PrdUptSwitch eNodeB
switch LST
CELLIDPRDUPT
MOD
CELLIDPRDUPT
CellIdPrdUpt ActionTime Action time eNodeB
LST
CELLIDPRDUPT
MOD
CELLIDPRDUPT
CellIdPrdUpt Period Period eNodeB
LST
CELLIDPRDUPT
ADD
ENBRSVDPARA
MOD
ENBRSVDPARA
eNBRsvdPara eNodeBId eNodeB ID eNodeB
RMV
ENBRSVDPARA
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved Switch MOD
eNBRsvdPara RsvdSwPara0 eNodeB
Parameter 0 ENBRSVDPARA
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved Switch MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved Switch MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
eNBRsvdPara RsvdPara2 eNodeB
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
ADD
ENBRSVDPARA
Reserved MOD
LST
ENBRSVDPARA
MOD
ENODEBALGOSWI
Handover Algo TCH
ENodeBAlgoSwitch HoAlgoSwitch eNodeB
switch LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
Handover Mode TCH
ENodeBAlgoSwitch HoModeSwitch eNodeB
switch LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
DlIcic algorithm TCH
ENodeBAlgoSwitch DlIcicSwitch eNodeB
switch LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
ANR algorithm TCH
ENodeBAlgoSwitch AnrSwitch eNodeB
switch LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch RedirectSwitch Redirection switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
MRO algorithm TCH
ENodeBAlgoSwitch MroSwitch eNodeB
switch LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch TpeSwitch TPE switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch UlIcicTimeSwitch UlIcic time switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch UlIcicFreqSwitch UlIcic freq switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch LcsSwitch LCS switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch TrmSwitch TRM switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
PciConflictAlmSwitc PCI conflict alarm TCH
ENodeBAlgoSwitch eNodeB
h switch LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch PowerSaveSwitch Power save switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
TCH
ENodeBAlgoSwitch RimSwitch RIM switch eNodeB
LST
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
ANR Under RAN
RanSharingAnrSwit TCH
ENodeBAlgoSwitch Sharing Algorithm eNodeB
ch LST
Switch
ENODEBALGOSWI
TCH
MOD
ENODEBALGOSWI
Frequency Layer TCH
ENodeBAlgoSwitch FreqLayerSwtich eNodeB
Switch LST
ENODEBALGOSWI
TCH
SET
LICENSEALMTHD
LICENSEALMTHD OPRD OPRD eNodeB
LST
LICENSEALMTHD
SET
LICENSEALMTHD
LICENSEALMTHD OTHD OTHD eNodeB
LST
LICENSEALMTHD
SET
LICENSEALMTHD
LICENSEALMTHD RPRD RPRD eNodeB
LST
LICENSEALMTHD
SET
LICENSEALMTHD
LICENSEALMTHD RTHD RTHD eNodeB
LST
LICENSEALMTHD
Uplink Traffic MOD LICRATIO

LicRatio UpLicRatio eNodeB
License Ratio LST LICRATIO
MOD LICRATIO
LicRatio TrafficSharingType Traffic Sharing Type eNodeB
LST LICRATIO
Operator 1 Traffic MOD LICRATIO

LicRatio Operator1TrfRatio eNodeB
Ratio LST LICRATIO
Ratio LST LICRATIO

Ratio LST LICRATIO

Ratio LST LICRATIO
Ratio LST LICRATIO

Ratio LST LICRATIO
Operator1TrfSharin Operator 1 Traffic MOD LICRATIO

LicRatio eNodeB
gRatio Sharing Ratio LST LICRATIO
LicRatio eNodeB

LicRatio eNodeB

LicRatio eNodeB
LicRatio eNodeB

LicRatio eNodeB
MRO optimization MOD MRO

MRO OptPeriod eNodeB
period LST MRO
Ncell optimization MOD MRO
MRO NcellOptThd eNodeB
threshold LST MRO
MRO statistics MOD MRO

MRO StatNumThd eNodeB
number threshold LST MRO
Pingpong handover MOD MRO

MRO PingpongTimeThd eNodeB
threshold LST MRO
Pingpong ratio MOD MRO
MRO PingpongRatioThd eNodeB
threshold LST MRO
Abnormal coverage MOD MRO

MRO CoverAbnormalThd eNodeB
threshold LST MRO
Serving cell RSRP MOD MRO
MRO ServingRsrpThd eNodeB
threshold LST MRO
Neighbour cell MOD MRO
MRO NeighborRsrpThd eNodeB
RSRP threshold LST MRO
LST SIMULOAD
SimuLoad SimuLoadCfgIndex configuration index eNodeB
MOD SIMULOAD
MOD SIMULOAD
SimuLoad SimuLoadRbThd RB usage threshold eNodeB
LST SIMULOAD
Power usage MOD SIMULOAD
SimuLoad SimuLoadPwrThd eNodeB
threshold LST SIMULOAD
SimuLoadReportPe MOD SIMULOAD

SimuLoad Report period eNodeB
riod LST SIMULOAD
SimuLoadStatPerio MOD SIMULOAD

SimuLoad Statistic period eNodeB
d LST SIMULOAD
Frequency selective MOD SIMULOAD

SimuLoad FreqSelSwitch eNodeB
switch LST SIMULOAD
MOD
TCPACKCTRLALG
TCP ACK Control O
TcpAckCtrlAlgo AckCtrlSwitch eNodeB
Switch LST
TCPACKCTRLALG
O
MOD
TCPACKCTRLALG
O
TcpAckCtrlAlgo DlMaxThroughput DL Max Throughput eNodeB
LST
TCPACKCTRLALG
O
MOD
TCPACKCTRLALG
Control Timer O
TcpAckCtrlAlgo CtrlTimerLength eNodeB
Length LST
TCPACKCTRLALG
O
MOD
TDDFRAMEOFFSE
T
TddFrameOffset TimeOffset TDD time offset eNodeB
LST
TDDFRAMEOFFSE
T
MOD TPEALGO
TpeAlgo PortListNum TCP Port Number eNodeB
LST TPEALGO
MOD TPEALGO
TpeAlgo Port1 TCP Port 1 eNodeB
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
MOD TPEALGO
LST TPEALGO
ADD
NODETORSCGRP
LST
OBJTORSCGROU NODETORSCGRP
NODETORSCGRP Mapping ID eNodeB
PID MOD
NODETORSCGRP
RMV
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP S1X2FLAG S1/X2 Identifier eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP ISALLMATCH IsAllMatch eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP ENDPOINTID Node Identifier eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP CABINETNO CabinetNo eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP SUBRACKNO SubrackNo eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP SLOTNO SlotNo eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
Transmission
MOD
NODETORSCGRP RSCGRPT Resource Group eNodeB
NODETORSCGRP
Bear Type
LST
NODETORSCGRP
ADD
NODETORSCGRP
Transmission MOD
NODETORSCGRP RSCGRPN eNodeB
Resource Group ID NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP SBT Subboard Type eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP PN Bearing Port No. eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
NODETORSCGRP
MOD
NODETORSCGRP PT Bearing Port Type eNodeB
NODETORSCGRP
LST
NODETORSCGRP
ADD
SONSECPARA
LST
SONSECPARANA Son IPsec SONSECPARA
SonSecPara eNodeB
ME Parameter Name MOD
SONSECPARA
RMV
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara PROPID IKE Proposal ID eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
IPsec Proposal MOD
SonSecPara PROPNAME eNodeB
Name SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara APPTYPE Application Type eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara IKEVERSION IKE Version eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara EXCHMODE Exchange Mode eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara PKEY Pre-shared Key eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara DPD DPD Mode eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara DPDIDLETIME DPD Idle Time eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
DPD
MOD
SonSecPara DPDRETRI Retransmission eNodeB
SONSECPARA
Interval
LST
SONSECPARA
ADD
SONSECPARA
DPD
MOD
SonSecPara DPDRETRN Retransmission eNodeB
SONSECPARA
Count
LST
SONSECPARA
ADD
SONSECPARA
Perfect Forward MOD
SonSecPara PFS eNodeB
Secrecy SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara LTCFG SA Duration Mode eNodeB
SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
Lifetime Based On MOD
SonSecPara LTS eNodeB
Time SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
Lifetime Based On MOD
SonSecPara LTKB eNodeB
Traffic SONSECPARA
LST
SONSECPARA
ADD
SONSECPARA
MOD
SonSecPara CNOPERATORID CN Operator ID eNodeB
SONSECPARA
LST
SONSECPARA
ADD MME6
DSP MME6
MME6 MMEID MME6 ID eNodeB LST MME6
MOD MME6
RMV MME6
ADD MME6
First Signaling IPv6
MME6 SIGIP1 eNodeB MOD MME6
Address
LST MME6
ADD MME6
First Signaling IP
MME6 SIGIP1SECFLAG eNodeB MOD MME6
IPsec Flag
LST MME6
ADD MME6
First IPv6 IKEPeer
MME6 IKEPEERNM1 eNodeB MOD MME6
Name
LST MME6
ADD MME6
First IPsec Proposal
MME6 IPSECPROPNM1 eNodeB MOD MME6
Name
LST MME6
ADD MME6
Second Signaling
MME6 SIGIP2 eNodeB MOD MME6
IPv6 Address
LST MME6
ADD MME6
Second Signaling
MME6 SIGIP2SECFLAG eNodeB MOD MME6
IP IPsec Flag
LST MME6
ADD MME6
Second IPv6
MME6 IKEPEERNM2 eNodeB MOD MME6
IKEPeer Name
LST MME6
ADD MME6
Second IPsec
MME6 IPSECPROPNM2 eNodeB MOD MME6
Proposal Name
LST MME6
ADD MME6
MME6 LOCPORT App Port No. eNodeB MOD MME6
LST MME6
ADD MME6
Description of IPv6
MME6 DESCRIPTION eNodeB MOD MME6
MME
LST MME6
ADD MME6
MME6 CNOPERATORID CN Operator ID eNodeB MOD MME6
LST MME6
ADD MME6
MME6 MMERELEASE MME Release eNodeB MOD MME6
LST MME6
ADD MME
DSP MME
MME MMEID MME ID eNodeB LST MME
MOD MME
RMV MME
ADD MME
MME FIRSTSIGIP First Signalling IP eNodeB MOD MME
LST MME
ADD MME
MME FIRSTIPSECFLAG First IPSec Flag eNodeB MOD MME
LST MME
ADD MME
MME FIRSTIKEPEERNM First IKEPeer Name eNodeB MOD MME
LST MME
ADD MME
FIRSTIPSECPROP First IPsec Proposal
MME eNodeB MOD MME
NM Name
LST MME
ADD MME
Second Signalling
MME SECSIGIP eNodeB MOD MME
IP
LST MME
ADD MME
MME SECIPSECFLAG Second IPSec Flag eNodeB MOD MME
LST MME
ADD MME
Second IKEPeer
MME SECIKEPEERNM eNodeB MOD MME
Name
LST MME
ADD MME
SECIPSECPROPN Second IPsec
MME eNodeB MOD MME
M Proposal Name
LST MME
ADD MME
MME LOCPORT App Port No. eNodeB MOD MME
LST MME
ADD MME
MME DESCRIPTION Description of MME eNodeB MOD MME
LST MME
ADD MME
MME CNOPERATORID CN Operator ID eNodeB MOD MME
LST MME
ADD MME
MME MMERELEASE MME Release eNodeB MOD MME
LST MME
ADD S1SERVIP
MOD S1SERVIP
S1ServIP CN Cabinet No. eNodeB
DSP X2ENODEB
LST S1SERVIP
ADD S1SERVIP
S1ServIP SRN Subrack No. eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP
S1ServIP SN Slot No. eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP
LST S1SERVIP
S1ServIP S1SERVIPID S1 Service IP ID eNodeB
MOD S1SERVIP
RMV S1SERVIP
ADD S1SERVIP
S1ServIP S1SERVIP S1 Service IP eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP
S1ServIP IPSECFLAG IPSec Flag eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP
S1ServIP IKEIP Local IKE IP eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP
S1ServIP PATHCHK Path Check eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP
S1ServIP CNOPERATORID CN Operator ID eNodeB MOD S1SERVIP
LST S1SERVIP
ADD S1SERVIP6
LST S1SERVIP6
S1ServIP6 S1ServIP6ID S1ServIP6 ID eNodeB
MOD S1SERVIP6
RMV S1SERVIP6
ADD S1SERVIP6
S1ServIP6 CN Cabinet No. eNodeB MOD S1SERVIP6
LST S1SERVIP6
ADD S1SERVIP6
S1ServIP6 SRN Subrack No. eNodeB MOD S1SERVIP6
LST S1SERVIP6
ADD S1SERVIP6
S1ServIP6 SN Slot No. eNodeB MOD S1SERVIP6
LST S1SERVIP6
ADD S1SERVIP6
Local Service IPv6
S1ServIP6 SERVIP eNodeB MOD S1SERVIP6
Address
LST S1SERVIP6
ADD S1SERVIP6
Service IP IPsec
S1ServIP6 SERVIPSECFLAG eNodeB MOD S1SERVIP6
Flag
LST S1SERVIP6
ADD S1SERVIP6
S1ServIP6 SERVIKEIP Service IPv6 IKE IP eNodeB MOD S1SERVIP6
LST S1SERVIP6
ADD S1SERVIP6
S1ServIP6 PATHCHK Path Check eNodeB MOD S1SERVIP6
LST S1SERVIP6
ADD S1SERVIP6
S1ServIP6 CNOPERATORID CN Operator ID eNodeB MOD S1SERVIP6
LST S1SERVIP6
ADD S1SIGIP
S1SigIP CN Cabinet No. eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP SRN Subrack No. eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP SN Slot No. eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
LST S1SIGIP
S1SigIP S1SIGIPID S1 Signal IP ID eNodeB
MOD S1SIGIP
RMV S1SIGIP
ADD S1SIGIP
S1SigIP LOCIP Local IP eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP LOCIPSECFLAG Local IPSec Flag eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP LOCIKEIP Local IKE IP eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP SECLOCIP Second Local IP eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
SECLOCIPSECFLA Second Local
S1SigIP eNodeB MOD S1SIGIP
G IPSec Flag
LST S1SIGIP
ADD S1SIGIP
Second Local IKE
S1SigIP SECLOCIKEIP eNodeB MOD S1SIGIP
IP
LST S1SIGIP
ADD S1SIGIP
S1SigIP LOCPORT Local Port No. eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP RTOMIN RTO Min Value eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP RTOMAX RTO Max Value eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP RTOINIT RTO Initial Value eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP RTOALPHA RTO Alpha Value eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP RTOBETA RTO Beta Value eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP HBINTER Heart-beat Interval eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
Max Association
S1SigIP MAXASSOCRETR eNodeB MOD S1SIGIP
Retransmission
LST S1SIGIP
ADD S1SIGIP
Max Path
S1SigIP MAXPATHRETR eNodeB MOD S1SIGIP
Retransmission
LST S1SIGIP
ADD S1SIGIP
Transmit Message
S1SigIP CHKSUMTX eNodeB MOD S1SIGIP
Checksum Flag
LST S1SIGIP
ADD S1SIGIP
Receive Message
S1SigIP CHKSUMRX eNodeB MOD S1SIGIP
Checksum Flag
LST S1SIGIP
ADD S1SIGIP
Checksum
S1SigIP CHKSUMTYPE eNodeB MOD S1SIGIP
Arithmetic Type
LST S1SIGIP
ADD S1SIGIP
SWITCHBACKFLA
S1SigIP Switch Back Flag eNodeB MOD S1SIGIP
G
LST S1SIGIP
ADD S1SIGIP
SWITCHBACKHBN Heart-beat Times
S1SigIP eNodeB MOD S1SIGIP
UM When Switch Back
LST S1SIGIP
ADD S1SIGIP
S1SigIP TSACK SACK Timeout eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP
S1SigIP CNOPERATORID CN Operator ID eNodeB MOD S1SIGIP
LST S1SIGIP
ADD S1SIGIP6
LST S1SIGIP6
S1SigIP6 S1SIGIP6ID S1SigIP6 ID eNodeB
MOD S1SIGIP6
RMV S1SIGIP6
ADD S1SIGIP6
S1SigIP6 CN Cabinet No. eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 SRN Subrack No. eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 SN Slot No. eNodeB MOD S1SIGIP6
LST S1SIGIP6
First Local ADD S1SIGIP6

S1SigIP6 SIGIP1 Signaling IPv6 eNodeB MOD S1SIGIP6
Address LST S1SIGIP6
ADD S1SIGIP6
First Signaling IP
S1SigIP6 SIGIP1SECFLAG eNodeB MOD S1SIGIP6
IPsec Flag
LST S1SIGIP6
ADD S1SIGIP6
First Sigaling IPv6
S1SigIP6 SIGIKEIP eNodeB MOD S1SIGIP6
IKE IP
LST S1SIGIP6
Second Local ADD S1SIGIP6
S1SigIP6 SIGIP2 Signaling IPv6 eNodeB MOD S1SIGIP6
Address LST S1SIGIP6
ADD S1SIGIP6
Second Signaling
S1SigIP6 SIGIP2SECFLAG eNodeB MOD S1SIGIP6
IP IPsec Flag
LST S1SIGIP6
ADD S1SIGIP6
Second Signaling
S1SigIP6 SIGIKEIP2 eNodeB MOD S1SIGIP6
IPv6 IKE IP
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 LOCPORT Local Port No. eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 RTOMIN RTO Min Value eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 RTOMAX RTO Max Value eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 RTOINIT RTO Initial Value eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 RTOALPHA RTO Alpha Value eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 RTOBETA RTO Beta Value eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 HBINTER Heart-beat Interval eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD S1SIGIP6
Max Association
S1SigIP6 MAXASSOCRETR eNodeB MOD S1SIGIP6
Retransmission
LST S1SIGIP6
ADD S1SIGIP6
Max Path
S1SigIP6 MAXPATHRETR eNodeB MOD S1SIGIP6
Retransmission
LST S1SIGIP6
ADD S1SIGIP6
Transmit Message
S1SigIP6 CHKSUMTX eNodeB MOD S1SIGIP6
Checksum Flag
LST S1SIGIP6
ADD S1SIGIP6
Receive Message
S1SigIP6 CHKSUMRX eNodeB MOD S1SIGIP6
Checksum Flag
LST S1SIGIP6
ADD S1SIGIP6
Checksum
S1SigIP6 CHKSUMTYPE eNodeB MOD S1SIGIP6
Arithmetic Type
LST S1SIGIP6
ADD S1SIGIP6
SWITCHBACKFLA
S1SigIP6 Switch Back Flag eNodeB MOD S1SIGIP6
G
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 eNodeB MOD S1SIGIP6
UM When Switch Back
LST S1SIGIP6
ADD S1SIGIP6
S1SigIP6 CNOPERATORID CN Operator ID eNodeB MOD S1SIGIP6
LST S1SIGIP6
ADD SGW
DSP SGW
SGW SGWID Service Gateway ID eNodeB LST SGW
MOD SGW
RMV SGW
ADD SGW
SGW SERVIP1 First Service IP eNodeB MOD SGW
LST SGW
ADD SGW
SERVIP1IPSECFL First Service IP
SGW eNodeB MOD SGW
AG IPSec Flag
LST SGW
ADD SGW
SERVIP1IKEPEER First Service IP
SGW eNodeB MOD SGW
NM IKEPeer Name
LST SGW
First Service IP ADD SGW

SERVIP1IPSECPR
SGW IPsec Proposal eNodeB MOD SGW
OPNM
Name LST SGW
ADD SGW
SGW SERVIP2 Second Service IP eNodeB MOD SGW
LST SGW
ADD SGW
SERVIP2IPSECFL Second Service IP
SGW eNodeB MOD SGW
AG IPSec Flag
LST SGW
ADD SGW
SERVIP2IKEPEER Second Service IP
SGW eNodeB MOD SGW
NM IKEPeer Name
LST SGW
Second Service IP ADD SGW

SERVIP2IPSECPR
OPNM
Name LST SGW
ADD SGW
SGW SERVIP3 Third Service IP eNodeB MOD SGW
LST SGW
ADD SGW
SERVIP3IPSECFL Third Service IP
SGW eNodeB MOD SGW
AG IPSec Flag
LST SGW
ADD SGW
SERVIP3IKEPEER Third Service IP
SGW eNodeB MOD SGW
NM IKEPeer Name
LST SGW
Third Service IP ADD SGW

SERVIP3IPSECPR
OPNM
Name LST SGW
ADD SGW
SGW SERVIP4 Fourth Service IP eNodeB MOD SGW
LST SGW
ADD SGW
SERVIP4IPSECFL Fourth Service IP
SGW eNodeB MOD SGW
AG IPSec Flag
LST SGW
ADD SGW
SERVIP4IKEPEER Fourth Service IP
SGW eNodeB MOD SGW
NM IKEPeer Name
LST SGW
Fourth Service IP ADD SGW

SERVIP4IPSECPR
OPNM
Name LST SGW
ADD SGW
SGW DESCRIPTION Description of SGW eNodeB MOD SGW
LST SGW
ADD SGW
SGW CNOPERATORID CN Operator ID eNodeB MOD SGW
LST SGW
ADD SGW6
DSP SGW6
SGW6 SGWID SGW6 ID eNodeB LST SGW6
MOD SGW6
RMV SGW6
ADD SGW6
First Service IPv6
SGW6 SERVIP1 eNodeB MOD SGW6
Address
LST SGW6
ADD SGW6
SGW6 eNodeB MOD SGW6
AG IPsec Flag
LST SGW6
ADD SGW6
First IPv6 IKEPeer
SGW6 IKEPEERNM1 eNodeB MOD SGW6
Name
LST SGW6
ADD SGW6
SGW6 IPSECPROPNM1 eNodeB MOD SGW6
Name
LST SGW6
ADD SGW6
Second Service
IPv6 Address
LST SGW6
ADD SGW6
AG IPsec Flag
LST SGW6
ADD SGW6
Second IPv6
IKEPeer Name
LST SGW6
ADD SGW6
Second IPsec
Proposal Name
LST SGW6
ADD SGW6
Third Service IPv6
Address
LST SGW6
ADD SGW6
AG IPsec Flag
LST SGW6
ADD SGW6
Third IPv6 IKEPeer
Name
LST SGW6
ADD SGW6
Third IPsec
Proposal Name
LST SGW6
ADD SGW6
Fourth Service IPv6
Address
LST SGW6
ADD SGW6
AG IPsec Flag
LST SGW6
ADD SGW6
Fourth IPv6
IKEPeer Name
LST SGW6
ADD SGW6
Fourth IPsec
Proposal Name
LST SGW6
ADD SGW6
Description of
SGW6 DESCRIPTION eNodeB MOD SGW6
SGW6
LST SGW6
ADD SGW6
SGW6 CNOPERATORID CN Operator ID eNodeB MOD SGW6
LST SGW6
ADD X2SERVIP
X2ServIP CN Cabinet No. eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP SRN Subrack No. eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP SN Slot No. eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
LST X2SERVIP
X2ServIP X2SERVIPID X2 service IP ID eNodeB
MOD X2SERVIP
RMV X2SERVIP
ADD X2SERVIP
X2ServIP X2SERVIP X2 Service IP eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP IPSECFLAG IPSec Flag eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP SEGWFLAG SeGW Flag eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP LOCIKEIP Local IKE IP eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP IKEPEERNM IKEPeer Name eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
IPsec Proposal
X2ServIP IPSECPROPNM eNodeB MOD X2SERVIP
Name
LST X2SERVIP
ADD X2SERVIP
X2ServIP PATHCHK Path Check eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SERVIP
X2ServIP CNOPERATORID CN Operator ID eNodeB MOD X2SERVIP
LST X2SERVIP
ADD X2SIGIP
X2SigIP CN Cabinet No. eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP SRN Subrack No. eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP SN Slot No. eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
LST X2SIGIP
X2SigIP X2SIGIPID X2 signal IP ID eNodeB
MOD X2SIGIP
RMV X2SIGIP
ADD X2SIGIP
X2SigIP LOCIP Local IP eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP IPSECFLAG IPSec Flag eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP SEGWFLAG SeGW Flag eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP IKEIP Local IKE IP eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP IKEPEERNM IKEPeer Name eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
IPsec Proposal
X2SigIP IPSECPROPNM eNodeB MOD X2SIGIP
Name
LST X2SIGIP
ADD X2SIGIP
X2SigIP SECLOCIP Second Local IP eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP SECIPSECFLAG Second IPSec Flag eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP SECSEGWFLAG Second SeGW Flag eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP SECLOCIKEIP Second Local IKEIP eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
Second IKEPeer
X2SigIP SECIKEPEERNM eNodeB MOD X2SIGIP
Name
LST X2SIGIP
ADD X2SIGIP
SECIPSECPROPN Second IPsec
X2SigIP eNodeB MOD X2SIGIP
M Proposal Name
LST X2SIGIP
ADD X2SIGIP
X2SigIP LOCPORT Local Port No. eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP RTOMIN RTO Min Value eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP RTOMAX RTO Max Value eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP RTOINIT RTO Initial Value eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP RTOALPHA RTO Alpha Value eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP RTOBETA RTO Beta Value eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP HBINTER Heart-beat Interval eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
Max Association
X2SigIP MAXASSOCRETR eNodeB MOD X2SIGIP
Retransmission
LST X2SIGIP
ADD X2SIGIP
Max Path
X2SigIP MAXPATHRETR eNodeB MOD X2SIGIP
Retransmission
LST X2SIGIP
ADD X2SIGIP
Transmit Message
X2SigIP CHKSUMTX eNodeB MOD X2SIGIP
Checksum Flag
LST X2SIGIP
ADD X2SIGIP
Receive Message
X2SigIP CHKSUMRX eNodeB MOD X2SIGIP
Checksum Flag
LST X2SIGIP
ADD X2SIGIP
Checksum
X2SigIP CHKSUMTYPE eNodeB MOD X2SIGIP
Arithmetic Type
LST X2SIGIP
ADD X2SIGIP
SWITCHBACKFLA
X2SigIP Switch Back Flag eNodeB MOD X2SIGIP
G
LST X2SIGIP
ADD X2SIGIP
X2SigIP eNodeB MOD X2SIGIP
UM When Switch Back
LST X2SIGIP
ADD X2SIGIP
X2SigIP TSACK SACK Timeout eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2SIGIP
X2SigIP CNOPERATORID CN Operator ID eNodeB MOD X2SIGIP
LST X2SIGIP
ADD X2ENODEB
DSP X2ENODEB
X2eNodeB X2ENODEBID X2eNodeB ID eNodeB LST X2ENODEB
MOD X2ENODEB
RMV X2ENODEB
ADD X2ENODEB
X2eNodeB FIRSTSIGIP First Signalling IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
First Signalling IP
X2eNodeB FIRSTIPSECFLAG eNodeB MOD X2ENODEB
IPSec Flag
LST X2ENODEB
ADD X2ENODEB
X2eNodeB FIRSTSEGWFLAG First SeGW Flag eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB FIRSTIKEIP First IKE IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
Second Signalling
X2eNodeB SECSIGIP eNodeB MOD X2ENODEB
IP
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SECIPSECFLAG Second IPSec Flag eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SECSEGWFLAG Second SeGW Flag eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SECIKEIP Second IKE IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB APPPORT App Port No. eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SERVIP1 First Service IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB eNodeB MOD X2ENODEB
AG IPSec Flag
LST X2ENODEB
ADD X2ENODEB
SERVIP1SEGWFL First Service IP
AG SeGW Flag
LST X2ENODEB
ADD X2ENODEB
First Service IP IKE
X2eNodeB SERVIP1IKEIP eNodeB MOD X2ENODEB
IP
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SERVIP2 Second Service IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
AG IPSec Flag
LST X2ENODEB
ADD X2ENODEB
SERVIP2SEGWFL Second Service IP
AG SeGW Flag
LST X2ENODEB
ADD X2ENODEB
Second Service IP
IKE IP
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SERVIP3 Third Service IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
AG IPSecFlag
LST X2ENODEB
ADD X2ENODEB
SERVIP3SEGWFL Third Service IP
AG SeGW Flag
LST X2ENODEB
ADD X2ENODEB
Third Service IP
IKE IP
LST X2ENODEB
ADD X2ENODEB
X2eNodeB SERVIP4 Fourth Service IP eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
AG IPSec Flag
LST X2ENODEB
ADD X2ENODEB
SERVIP4SEGWFL Fourth Service IP
AG SeGW Flag
LST X2ENODEB
ADD X2ENODEB
Fourth Service IP
IKE IP
LST X2ENODEB
ADD X2ENODEB
Mobile Country
X2eNodeB MCC eNodeB MOD X2ENODEB
Code
LST X2ENODEB
ADD X2ENODEB
Mobile Network
X2eNodeB MNC eNodeB MOD X2ENODEB
Code
LST X2ENODEB
ADD X2ENODEB
X2eNodeB ENODEBID eNodeB ID eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
Description of
X2eNodeB DESCRIPTION eNodeB MOD X2ENODEB
X2eNodeB
LST X2ENODEB
ADD X2ENODEB
X2eNodeB CNOPERATORID CN Operator ID eNodeB MOD X2ENODEB
LST X2ENODEB
ADD X2ENODEB
TARGETENODEBR Target eNodeB
ELEASE Release
LST X2ENODEB
ADD X2SERVIP6
LST X2SERVIP6
X2ServIP6 X2ServIP6ID X2ServIP6 ID eNodeB
MOD X2SERVIP6
RMV X2SERVIP6
ADD X2SERVIP6
X2ServIP6 CN Cabinet No. eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SERVIP6
X2ServIP6 SRN Subrack No. eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SERVIP6
X2ServIP6 SN Slot No. eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SERVIP6
X2ServIP6 SERVIP Service IP eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SERVIP6
Service IP IPsec
X2ServIP6 SERVIPSECFLAG eNodeB MOD X2SERVIP6
Flag
LST X2SERVIP6
ADD X2SERVIP6
SERVIPSECGWFL Service IP SecGW
X2ServIP6 eNodeB MOD X2SERVIP6
AG Flag
LST X2SERVIP6
ADD X2SERVIP6
X2ServIP6 SERVIKEIP Service IKE IP eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SERVIP6
IPv6 IKEPeer
X2ServIP6 IKEPEERNM eNodeB MOD X2SERVIP6
Name
LST X2SERVIP6
ADD X2SERVIP6
IPsec Proposal
X2ServIP6 IPSECPROPNM eNodeB MOD X2SERVIP6
Name
LST X2SERVIP6
ADD X2SERVIP6
X2ServIP6 PATHCHK Path Check eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SERVIP6
X2ServIP6 CNOPERATORID CN Operator ID eNodeB MOD X2SERVIP6
LST X2SERVIP6
ADD X2SIGIP6
LST X2SIGIP6
X2SigIP6 X2SIGIP6ID X2SigIP6 ID eNodeB
MOD X2SIGIP6
RMV X2SIGIP6
ADD X2SIGIP6
X2SigIP6 CN Cabinet No. eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 SRN Subrack No. eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 SN Slot No. eNodeB MOD X2SIGIP6
LST X2SIGIP6
First Local ADD X2SIGIP6

X2SigIP6 SIGIP1 Signaling IPv6 eNodeB MOD X2SIGIP6
Address LST X2SIGIP6
ADD X2SIGIP6
First Signaling IP
X2SigIP6 SIGIP1SECFLAG eNodeB MOD X2SIGIP6
IPsec Flag
LST X2SIGIP6
ADD X2SIGIP6
First Signaling IP
X2SigIP6 SIGIP1SEGWFLAG eNodeB MOD X2SIGIP6
SecGW Flag
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 SIGIKEIP1 eNodeB MOD X2SIGIP6
IKE IP
LST X2SIGIP6
ADD X2SIGIP6
First IPv6 IKEPeer
X2SigIP6 IKEPEERNM1 eNodeB MOD X2SIGIP6
Name
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 IPSECPROPNM1 eNodeB MOD X2SIGIP6
Name
LST X2SIGIP6
Second Local ADD X2SIGIP6

X2SigIP6 SIGIP2 Signaling IPv6 eNodeB MOD X2SIGIP6
Address LST X2SIGIP6
ADD X2SIGIP6
Second Signaling
X2SigIP6 SIGIP2SECFLAG eNodeB MOD X2SIGIP6
IP IPsec Flag
LST X2SIGIP6
ADD X2SIGIP6
Second Signaling
X2SigIP6 SIGIP2SEGWFLAG eNodeB MOD X2SIGIP6
IP SeGW Flag
LST X2SIGIP6
ADD X2SIGIP6
Second Signaling
X2SigIP6 SIGIKEIP2 eNodeB MOD X2SIGIP6
IPv6 IKE IP
LST X2SIGIP6
ADD X2SIGIP6
Second IPv6
X2SigIP6 IKEPEERNM2 eNodeB MOD X2SIGIP6
IKEPeer Name
LST X2SIGIP6
ADD X2SIGIP6
Second IPsec
X2SigIP6 IPSECPROPNM2 eNodeB MOD X2SIGIP6
Proposal Name
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 LOCPORT Local Port No. eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 RTOMIN RTO Min Value eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 RTOMAX RTO Max Value eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 RTOINIT RTO Initial Value eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 RTOALPHA RTO Alpha Value eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 RTOBETA RTO Beta Value eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 HBINTER Heart-beat Interval eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2SIGIP6
Max Association
X2SigIP6 MAXASSOCRETR eNodeB MOD X2SIGIP6
Retransmission
LST X2SIGIP6
ADD X2SIGIP6
Max Path
X2SigIP6 MAXPATHRETR eNodeB MOD X2SIGIP6
Retransmission
LST X2SIGIP6
ADD X2SIGIP6
Transmit Message
X2SigIP6 CHKSUMTX eNodeB MOD X2SIGIP6
Checksum Flag
LST X2SIGIP6
ADD X2SIGIP6
Receive Message
X2SigIP6 CHKSUMRX eNodeB MOD X2SIGIP6
Checksum Flag
LST X2SIGIP6
ADD X2SIGIP6
Checksum
X2SigIP6 CHKSUMTYPE eNodeB MOD X2SIGIP6
Arithmetic Type
LST X2SIGIP6
ADD X2SIGIP6
SWITCHBACKFLA
X2SigIP6 Switch Back Flag eNodeB MOD X2SIGIP6
G
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 eNodeB MOD X2SIGIP6
UM When Switch Back
LST X2SIGIP6
ADD X2SIGIP6
X2SigIP6 CNOPERATORID CN Operator ID eNodeB MOD X2SIGIP6
LST X2SIGIP6
ADD X2ENODEB6
DSP X2ENODEB6
X2eNodeB6 X2ENODEBID X2eNodeB6 ID eNodeB LST X2ENODEB6
MOD X2ENODEB6
RMV X2ENODEB6
ADD X2ENODEB6
X2eNodeB6 SIGIP1 eNodeB MOD X2ENODEB6
Address
LST X2ENODEB6
ADD X2ENODEB6
First Signaling IP
X2eNodeB6 SIGIP1SECFLAG eNodeB MOD X2ENODEB6
IPsec Flag
LST X2ENODEB6
ADD X2ENODEB6
First Signaling IP
X2eNodeB6 SIGIP1SEGWFLAG eNodeB MOD X2ENODEB6
SeGW Flag
LST X2ENODEB6
ADD X2ENODEB6
X2eNodeB6 SIGIKEIP1 eNodeB MOD X2ENODEB6
IKE IP
LST X2ENODEB6
ADD X2ENODEB6
Second Signaling
X2eNodeB6 SIGIP2 eNodeB MOD X2ENODEB6
IPv6 Address
LST X2ENODEB6
ADD X2ENODEB6
Second Signaling
X2eNodeB6 SIGIP2SECFLAG eNodeB MOD X2ENODEB6
IP IPsec Flag
LST X2ENODEB6
ADD X2ENODEB6
SIGIP2SECGWFLA Second Signaling
X2eNodeB6 eNodeB MOD X2ENODEB6
G IP SeGW Flag
LST X2ENODEB6
ADD X2ENODEB6
Second Signaling
X2eNodeB6 SIGIKEIP2 eNodeB MOD X2ENODEB6
IPv6 IKE IP
LST X2ENODEB6
ADD X2ENODEB6
X2eNodeB6 LOCPORT App Port No. eNodeB MOD X2ENODEB6
LST X2ENODEB6
ADD X2ENODEB6
First Service IPv6
X2eNodeB6 SERVIP1 eNodeB MOD X2ENODEB6
Address
LST X2ENODEB6
ADD X2ENODEB6
AG IPsec Flag
LST X2ENODEB6
ADD X2ENODEB6
SERVIP1SECGWF First Service IP
LAG SeGW Flag
LST X2ENODEB6
ADD X2ENODEB6
First Service IPv6
X2eNodeB6 SERVIKEIP1 eNodeB MOD X2ENODEB6
IKE IP
LST X2ENODEB6
ADD X2ENODEB6
Second Service
IPv6 Address
LST X2ENODEB6
ADD X2ENODEB6
AG IPsec Flag
LST X2ENODEB6
ADD X2ENODEB6
SERVIP2SEGWFL Second Service IP
AG SeGW Flag
LST X2ENODEB6
ADD X2ENODEB6
Second Service
IPv6 IKE IP
LST X2ENODEB6
ADD X2ENODEB6
Third Service IPv6
Address
LST X2ENODEB6
ADD X2ENODEB6
AG IPsec Flag
LST X2ENODEB6
ADD X2ENODEB6
SERVIP3SEGWFL Third Service IP
AG SeGW Flag
LST X2ENODEB6
ADD X2ENODEB6
Third Service IPv6
IKE IP
LST X2ENODEB6
ADD X2ENODEB6
Fourth Service IPv6
Address
LST X2ENODEB6
ADD X2ENODEB6
AG IPsec Flag
LST X2ENODEB6
ADD X2ENODEB6
SERVIP4SEGWFL Fourth Service IP
AG SeGW Flag
LST X2ENODEB6
ADD X2ENODEB6
Fourth Service IPv6
IKE IP
LST X2ENODEB6
ADD X2ENODEB6
Mobile Country
X2eNodeB6 MCC eNodeB MOD X2ENODEB6
Code
LST X2ENODEB6
ADD X2ENODEB6
Mobile Network
X2eNodeB6 MNC eNodeB MOD X2ENODEB6
Code
LST X2ENODEB6
ADD X2ENODEB6
X2eNodeB6 ENODEBID eNodeB ID eNodeB MOD X2ENODEB6
LST X2ENODEB6
ADD X2ENODEB6
Description of
X2eNodeB6 DESCRIPTION eNodeB MOD X2ENODEB6
X2eNodeB6
LST X2ENODEB6
ADD X2ENODEB6
X2eNodeB6 CNOPERATORID CN Operator ID eNodeB MOD X2ENODEB6
LST X2ENODEB6
ADD X2ENODEB6
TARGETENODEBR Target eNodeB
ELEASE Release
LST X2ENODEB6
ADD CA
LST CA
Certificate Authority
CA CANAME eNodeB MOD CA
Name
REQ DEVCERT
RMV CA
ADD CA
CA URL eNodeB MOD CA
URL
LST CA
ADD CA
CA SIGNALG Signature Algorithm eNodeB MOD CA
LST CA
ADD CA
Certificate Fetch
CA MODE eNodeB MOD CA
Mode
LST CA
ADD CA
Certificate Update
CA UPDSIP eNodeB MOD CA
Source IP
LST CA
ADD CA
CA URL During Site
CA INITREQURL eNodeB MOD CA
Deployment
LST CA
Source IP for
ADD CA
Applying for a
CA INITREQSIP eNodeB MOD CA
Certificate During
LST CA
Site Deployment
MOD CERTREQ
CERTREQ COMMNAME Common Name eNodeB
LST CERTREQ
Common Name MOD CERTREQ

CERTREQ USERADDINFO eNodeB
Additional Info. LST CERTREQ
MOD CERTREQ
CERTREQ COUNTRY Country eNodeB
LST CERTREQ
MOD CERTREQ
CERTREQ ORG Organization eNodeB
LST CERTREQ
MOD CERTREQ
CERTREQ ORGUNIT Organizational Unit eNodeB
LST CERTREQ
STATEPROVINCE MOD CERTREQ
CERTREQ State or Province eNodeB
NAME LST CERTREQ
MOD CERTREQ
CERTREQ LOCALITY Locality eNodeB
LST CERTREQ
MOD CERTREQ
CERTREQ KEYUSAGE Key Usage eNodeB LST CERTFILE
LST CERTREQ
MOD CERTREQ
CERTREQ SIGNALG Signature Algorithm eNodeB LST CERTFILE
LST CERTREQ
MOD CERTREQ
CERTREQ KEYSIZE Key Size eNodeB UPD DEVCERT
LST CERTREQ
MOD CERTREQ
CERTREQ LOCALNAME Local Name eNodeB LST CERTFILE
LST CERTREQ
MOD CERTREQ
CERTREQ LOCALIP Local IP eNodeB LST CERTFILE
LST CERTREQ
ADD CERTMK
DSP CERTMK
REQ DEVCERT
Certificate File RMV CERTMK
CERTMK APPCERT eNodeB
Name UPD DEVCERT
DSP
CMPSESSION
LST CERTMK
CERTMK SERIALNO Serial Number eNodeB DSP CERTMK

DSP CERTMK
CERTMK COMMNAME Common Name eNodeB
LST CERTFILE
DSP CERTMK
CERTMK ISSUER Issuer eNodeB
LST CERTFILE
CERTMK DATE Expiration Date eNodeB DSP CERTMK
CERTMK EFFECTDATE Effective Date eNodeB DSP CERTMK
DSP APPCERT
LST APPCERT
APPCERT APPTYPE Application Type eNodeB MOD APPCERT
TST APPCERT
LST CERTTYPE
MOD APPCERT
Certificate File TST APPCERT
APPCERT APPCERT eNodeB
Name DSP APPCERT
LST APPCERT
APPCERT ISSUER Issuer eNodeB DSP APPCERT
APPCERT COMMNAME Common Name eNodeB DSP APPCERT
APPCERT SERIALNO Serial Number eNodeB DSP APPCERT
APPCERT DATE Expiration Date eNodeB DSP APPCERT

APPCERT IKEPEER IKEPeer Name eNodeB TST APPCERT
APPCERT EFFECTDATE Effective Date eNodeB DSP APPCERT
APPCERT STATUS Status eNodeB DSP APPCERT
Application Type
APPCERT SUPPORTTYPE eNodeB None
Supported By NE
ADD CROSSCERT
Certificate File DSP CROSSCERT
CROSSCERT CERTNAME eNodeB
Name RMV CROSSCERT
LST CROSSCERT
CROSSCERT SERIALNO Serial Number eNodeB DSP CROSSCERT
CROSSCERT COMMNAME Common Name eNodeB DSP CROSSCERT
CROSSCERT ISSUER Issuer Name eNodeB DSP CROSSCERT

CROSSCERT DATE Expiring Date eNodeB DSP CROSSCERT
CROSSCERT STATUS Status eNodeB DSP CROSSCERT
CROSSCERT EFFECTDATE Effective Date eNodeB DSP CROSSCERT
ADD TRUSTCERT
Certificate File DSP TRUSTCERT
TRUSTCERT CERTNAME eNodeB
Name RMV TRUSTCERT
LST TRUSTCERT
TRUSTCERT SERIALNO Serial Number eNodeB DSP TRUSTCERT
TRUSTCERT COMMNAME Common Name eNodeB DSP TRUSTCERT
TRUSTCERT ISSUER Issuer Name eNodeB DSP TRUSTCERT
TRUSTCERT DATE Expiring Date eNodeB DSP TRUSTCERT
TRUSTCERT STATUS Status eNodeB DSP TRUSTCERT
TRUSTCERT EFFECTDATE Effective Date eNodeB DSP TRUSTCERT

ADD CRL
DSP CRL
CRL CERTNAME CRL File Name eNodeB
RMV CRL
LST CRL
CRL STATUS Status eNodeB DSP CRL
CRL ISSUER Issuer eNodeB DSP CRL
CRL NEXTDATE Next Update eNodeB DSP CRL
CRL THISDATE This Update eNodeB DSP CRL
ADD CRLTSK
CRLTSK IP IP Address eNodeB
LST CRLTSK
ADD CRLTSK
CRLTSK USR User Name eNodeB
LST CRLTSK
CRLTSK PWD Password eNodeB ADD CRLTSK

ADD CRLTSK
CRLTSK PORT Port No. eNodeB
LST CRLTSK
ADD CRLTSK
CRLTSK FILENAME File Name eNodeB
LST CRLTSK
Using CRL's Next ADD CRLTSK

CRLTSK ISCRLTIME eNodeB
Update LST CRLTSK
CRL Updating ADD CRLTSK

CRLTSK PERIOD eNodeB
Period LST CRLTSK
ADD CRLTSK
CRLTSK TSKID Task ID eNodeB LST CRLTSK
RMV CRLTSK
ADD CRLTSK
CRLTSK CRLGETMETHOD Access Method eNodeB
LST CRLTSK
ADD CRLTSK
CRLTSK SEARCHDN Distinguish Name eNodeB
LST CRLTSK
ADD CRLTSK
CRLTSK SIP Source IP eNodeB
LST CRLTSK
Certificate Validity SET CERTCHKTSK

CERTCHKTSK ISENABLE eNodeB
Period Checking LST CERTCHKTSK
SET CERTCHKTSK
CERTCHKTSK PERIOD Checking Period eNodeB
LST CERTCHKTSK
SET CERTCHKTSK
CERTCHKTSK ALMRNG Alarm Threshold eNodeB
LST CERTCHKTSK
SET CERTCHKTSK
CERTCHKTSK UPDATEMETHOD Update Method eNodeB
LST CERTCHKTSK
SET CRLPOLICY
CRLPOLICY CRLPOLICY CRL Using Policy eNodeB
LST CRLPOLICY
ADD ACL
LST ACL
ACL ACLID ACL ID eNodeB
MOD ACL
RMV ACL
ADD ACL
ACL ACLDESC Description eNodeB MOD ACL
LST ACL
ADD ACL6
LST ACL6
ACL6 ACLID IPv6 ACL ID eNodeB
MOD ACL6
RMV ACL6
ADD ACL6
ACL6 ACLDESC Description eNodeB MOD ACL6
LST ACL6
ADD ACLRULE
LST ACLRULE
ACLRULE ACLID ACL ID eNodeB
MOD ACLRULE
RMV ACLRULE
ADD ACLRULE
LST ACLRULE
ACLRULE RULEID Rule ID eNodeB
MOD ACLRULE
RMV ACLRULE
ADD ACLRULE
ACLRULE ACTION Action eNodeB
LST ACLRULE
ADD ACLRULE
ACLRULE PT Protocol Type eNodeB
LST ACLRULE
ADD ACLRULE
ACLRULE SIP Source IP Address eNodeB MOD ACLRULE
LST ACLRULE
ADD ACLRULE
ACLRULE SWC Source Wildcard eNodeB MOD ACLRULE
LST ACLRULE
ADD ACLRULE
ACLRULE SMPT Match Source Port eNodeB
LST ACLRULE
Source Port ADD ACLRULE
ACLRULE SOP eNodeB
Operate LST ACLRULE
ADD ACLRULE
ACLRULE SPT1 Source Port 1 eNodeB
LST ACLRULE
ADD ACLRULE
ACLRULE SPT2 Source Port 2 eNodeB
LST ACLRULE
ADD ACLRULE
Destination IP
ACLRULE DIP eNodeB MOD ACLRULE
Address
LST ACLRULE
ADD ACLRULE
Destination
ACLRULE DWC eNodeB MOD ACLRULE
Wildcard
LST ACLRULE
Match Destination ADD ACLRULE

ACLRULE DMPT eNodeB
Port LST ACLRULE
Destination Port ADD ACLRULE
ACLRULE DOP eNodeB
Operate LST ACLRULE
ADD ACLRULE
ACLRULE DPT1 Destination Port 1 eNodeB
LST ACLRULE
ADD ACLRULE
ACLRULE DPT2 Destination Port 2 eNodeB
LST ACLRULE
ADD ACLRULE
ACLRULE MDSCP Match DSCP eNodeB
LST ACLRULE
ADD ACLRULE
ACLRULE DSCP DSCP eNodeB
LST ACLRULE
Match Fragment ADD ACLRULE

ACLRULE MFRG eNodeB
Message LST ACLRULE
ADD ACLRULE
ACLRULE VLANIDOP VLAN ID Operate eNodeB MOD ACLRULE
LST ACLRULE
ADD ACLRULE
ACLRULE VLANID1 VLAN ID 1 eNodeB MOD ACLRULE
LST ACLRULE
ADD ACLRULE
ACLRULE VLANID2 VLAN ID 2 eNodeB MOD ACLRULE
LST ACLRULE
ADD ACLRULE6
LST ACLRULE6
ACLRULE6 ACLID IPv6 ACL ID eNodeB
MOD ACLRULE6
RMV ACLRULE6
ADD ACLRULE6
LST ACLRULE6
ACLRULE6 RULEID IPv6 Rule ID eNodeB
MOD ACLRULE6
RMV ACLRULE6
ADD ACLRULE6
ACLRULE6 ACTION IPv6 ACL Action eNodeB
LST ACLRULE6
ADD ACLRULE6
ACLRULE6 PT Protocol Type eNodeB
LST ACLRULE6
ADD ACLRULE6
Source IPv6
ACLRULE6 SIP eNodeB MOD ACLRULE6
Address
LST ACLRULE6
ADD ACLRULE6
Source Address
ACLRULE6 SPFXLEN eNodeB MOD ACLRULE6
Prefix Length
LST ACLRULE6
ADD ACLRULE6
ACLRULE6 SMPT Match Source Port eNodeB
LST ACLRULE6
Source Port ADD ACLRULE6
ACLRULE6 SOP eNodeB
Operate LST ACLRULE6
ADD ACLRULE6
ACLRULE6 SPT1 Source Port 1 eNodeB
LST ACLRULE6
ADD ACLRULE6
ACLRULE6 SPT2 Source Port 2 eNodeB
LST ACLRULE6
ADD ACLRULE6
Destination IPv6
ACLRULE6 DIP eNodeB MOD ACLRULE6
Address
LST ACLRULE6
ADD ACLRULE6
Destination Address
ACLRULE6 DPFXLEN eNodeB MOD ACLRULE6
Prefix Length
LST ACLRULE6
Match Destination ADD ACLRULE6

ACLRULE6 DMPT eNodeB
Port LST ACLRULE6
Destination Port ADD ACLRULE6
ACLRULE6 DOP eNodeB
Operate LST ACLRULE6
ADD ACLRULE6
ACLRULE6 DPT1 Destination Port 1 eNodeB
LST ACLRULE6
ADD ACLRULE6
ACLRULE6 DPT2 Destination Port 2 eNodeB
LST ACLRULE6
ADD ACLRULE6
ACLRULE6 MDSCP Match DSCP eNodeB
LST ACLRULE6
ADD ACLRULE6
ACLRULE6 DSCP DSCP eNodeB
LST ACLRULE6
ADD BFDSESSION
DSP BFDSESSION
MOD
BFDSESSION CN Cabinet No. eNodeB
BFDSESSION
RMV BFDSESSION
LST BFDSESSION
ADD BFDSESSION
DSP BFDSESSION
MOD
BFDSESSION SRN Subrack No. eNodeB
BFDSESSION
RMV BFDSESSION
LST BFDSESSION
ADD BFDSESSION
DSP BFDSESSION
MOD
BFDSESSION SN Slot No. eNodeB
BFDSESSION
RMV BFDSESSION
LST BFDSESSION
ADD BFDSESSION
DSP BFDSESSION
MOD
BFDSESSION BFDSN Session ID eNodeB
BFDSESSION
RMV BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION SRCIP Source IP eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION DSTIP Destination IP eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION HT Hop Type eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION MINTI Min TX Interval eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION MINRI Min RX Interval eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION DM Detection Multiplier eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION CATLOG Session Catalog eNodeB BFDSESSION
DSP BFDSESSION
LST BFDSESSION
ADD BFDSESSION
BFDSESSION DSCP DSCP eNodeB
LST BFDSESSION
BFDSESSION CLEAR Clear Statistic eNodeB DSP BFDSESSION
BFDSESSION FSMState Session State eNodeB DSP BFDSESSION
Active Detecting
BFDSESSION ActualMode eNodeB DSP BFDSESSION
Mode
Active Minimum Tx
BFDSESSION ActualMinTxInterval eNodeB DSP BFDSESSION
Interval
Active Minimum Rx
BFDSESSION ActualMinRxInterval eNodeB DSP BFDSESSION
Interval
Active Detection
BFDSESSION ActualDetectTime eNodeB DSP BFDSESSION
Time
BFDSESSION MyDiscreaminator My Discriminator eNodeB DSP BFDSESSION
BFDSESSION YourDiscreaminator Your Discriminator eNodeB DSP BFDSESSION
Number of TX
BFDSESSION TxPDUCount eNodeB DSP BFDSESSION
PDUs
Number of RX
BFDSESSION RxPDUCount eNodeB DSP BFDSESSION
PDUs
Total Number of Up
BFDSESSION UptoDownCount eNodeB DSP BFDSESSION
to Down Sessions
BFDSESSION Diagnostic Session Diagnosis eNodeB DSP BFDSESSION
ADD BFDSESSION
MOD
BFDSESSION VER Protocol Version eNodeB
BFDSESSION
LST BFDSESSION
SET
Certification Deploy
CERTDEPLOY DEPLOYTYPE eNodeB CERTDEPLOY
Position Type
LST CERTDEPLOY
SET
CERTDEPLOY CN Cabinet No. eNodeB CERTDEPLOY
LST CERTDEPLOY
SET
CERTDEPLOY SRN Subrack No. eNodeB CERTDEPLOY
LST CERTDEPLOY
SET
CERTDEPLOY SN Slot No. eNodeB CERTDEPLOY
LST CERTDEPLOY
ADD CFMBNDIP
CFMBNDIP MDNAME MD Name eNodeB RMV CFMBNDIP
LST CFMBNDIP
ADD CFMBNDIP
CFMBNDIP MANAME MA Name eNodeB RMV CFMBNDIP
LST CFMBNDIP
ADD CFMBNDIP
CFMBNDIP RMEPID RMEP ID eNodeB RMV CFMBNDIP
LST CFMBNDIP
ADD CFMBNDIP
CFMBNDIP BNDIP IP Address eNodeB RMV CFMBNDIP
LST CFMBNDIP
ADD CFMMA
DSP CFMMA
CFMMA MDNAME MD Name eNodeB MOD CFMMA
RMV CFMMA
LST CFMMA
ADD CFMMA
DSP CFMMA
CFMMA MANAME MA Name eNodeB MOD CFMMA
RMV CFMMA
LST CFMMA
ADD CFMMA
CFMMA CN Cabinet No. eNodeB
LST CFMMA
ADD CFMMA
CFMMA SRN Subrack No. eNodeB
LST CFMMA
ADD CFMMA
CFMMA SN Slot No. eNodeB
LST CFMMA
ADD CFMMA
CFMMA BNDVLAN Binding VLAN eNodeB DSP CFMMA
LST CFMMA
ADD CFMMA
CFMMA VLANID VLAN ID eNodeB DSP CFMMA
LST CFMMA
ADD CFMMA
MOD CFMMA
CFMMA VLANPRI VLAN Priority eNodeB
DSP CFMMA
LST CFMMA
ADD CFMMA
MOD CFMMA
CFMMA CCMINTL CCM TX Interval eNodeB
DSP CFMMA
LST CFMMA
CFMMA MEPNumber Number of MEPs eNodeB DSP CFMMA
CFMMA RMEPNumber Number of RMEPs eNodeB DSP CFMMA
CFMMA MEPList MEP List eNodeB DSP CFMMA
CFMMA RMEPList RMEP List eNodeB DSP CFMMA
ADD CFMMD
DSP CFMMD
CFMMD MDNAME MD Name eNodeB
RMV CFMMD
LST CFMMD
ADD CFMMD
DSP CFMMD
DSP CFMMA
CFMMD LEVEL MD Level eNodeB
DSP CFMMEP
DSP CFMRMEP
LST CFMMD
CFMMD MANumber MA Number eNodeB DSP CFMMD
CFMMD MANameList MA List eNodeB DSP CFMMD
ACT CFMCC
ADD CFMMEP
DEA CFMCC
CFMMEP MDNAME MD Name eNodeB
DSP CFMMEP
RMV CFMMEP
LST CFMMEP
ACT CFMCC
ADD CFMMEP
DEA CFMCC
CFMMEP MANAME MA Name eNodeB
DSP CFMMEP
RMV CFMMEP
LST CFMMEP
ACT CFMCC
ADD CFMMEP
DEA CFMCC
CFMMEP MEPID MEP ID eNodeB
DSP CFMMEP
RMV CFMMEP
LST CFMMEP
ADD CFMMEP
CFMMEP CN Cabinet No. eNodeB
LST CFMMEP
ADD CFMMEP
CFMMEP SRN Subrack No. eNodeB
LST CFMMEP
ADD CFMMEP
CFMMEP SN Slot No. eNodeB
LST CFMMEP
ADD CFMMEP
CFMMEP SBT Subboard Type eNodeB
LST CFMMEP
ADD CFMMEP
CFMMEP PT Port Type eNodeB
LST CFMMEP
ADD CFMMEP
CFMMEP PN Port No. eNodeB
LST CFMMEP
DSP CFMMEP
CFMMEP CCSW CC Switch eNodeB
LST CFMMEP
CFMMEP BindingVLAN Binding VLAN eNodeB DSP CFMMEP

CFMMEP VLANID VLAN ID eNodeB DSP CFMMEP
CFMMEP VLANPri VLAN Priority eNodeB DSP CFMMEP
Number of TX CCM
CFMMEP TxCCPDU eNodeB DSP CFMMEP
PDUs
Number of RX CCM
CFMMEP RxCCPDU eNodeB DSP CFMMEP
PDUs
Number of TX
CFMMEP TxLBPDU eNodeB DSP CFMMEP
Loopback PDUs
Number of RX
CFMMEP RxLBPDU eNodeB DSP CFMMEP
Loopback PDUs
Number of TX Link
CFMMEP TxLTPDU eNodeB DSP CFMMEP
Trace PDUs
Number of RX Link
CFMMEP RxLTPDU eNodeB DSP CFMMEP
Trace PDUs
Number of TX
CFMMEP TxSuccCFMPDU Success CFM eNodeB DSP CFMMEP
PDUs
Number of RX
CFMMEP RxSuccCFMPDU Success CFM eNodeB DSP CFMMEP
PDUs
Number of TX
TxDroppedCFMPD
CFMMEP Dropped CFM eNodeB DSP CFMMEP
U
PDUs
Number of RX
RxDroppedCFMPD
CFMMEP Dropped CFM eNodeB DSP CFMMEP
U
PDUs
ADD CFMRMEP
DSP CFMRMEP
CFMRMEP MDNAME MD Name eNodeB
RMV CFMRMEP
LST CFMRMEP
ADD CFMRMEP
DSP CFMRMEP
CFMRMEP MANAME MA Name eNodeB
RMV CFMRMEP
LST CFMRMEP
ADD CFMRMEP
DSP CFMRMEP
CFMRMEP RMEPID RMEP ID eNodeB
RMV CFMRMEP
LST CFMRMEP
ADD CFMRMEP
CFMRMEP MAC MAC Address eNodeB DSP CFMRMEP
LST CFMRMEP
CFMRMEP Status Status eNodeB DSP CFMRMEP
Actual MAC
CFMRMEP ActualMAC eNodeB DSP CFMRMEP
Address
CFMRMEP BindingVLAN Binding VLAN eNodeB DSP CFMRMEP
CFMRMEP VLANID VLAN ID eNodeB DSP CFMRMEP

Number of RX CCM
CFMRMEP RxCCMPDU eNodeB DSP CFMRMEP
PDUs
Number of Bound
CFMRMEP IPNumber eNodeB DSP CFMRMEP
IPs
CFMRMEP IPList IP Address List eNodeB DSP CFMRMEP
ADD DBGSVR
DSP DBGSVR
DBGSVR SERVICETYPE Service Type eNodeB MOD DBGSVR
RMV DBGSVR
LST DBGSVR
ADD DBGSVR
DSP DBGSVR
DBGSVR SERVICEPORT Service Port eNodeB MOD DBGSVR
RMV DBGSVR
LST DBGSVR
ADD DBGSVR
MOD DBGSVR
DBGSVR SWITCH Enable Flag eNodeB
DSP DBGSVR
LST DBGSVR
ADD DEVIP
DSP DEVIP
DEVIP CN Cabinet No. eNodeB
RMV DEVIP
LST DEVIP
ADD DEVIP
DSP DEVIP
DEVIP SRN Subrack No. eNodeB
RMV DEVIP
LST DEVIP
ADD DEVIP
DSP DEVIP
DEVIP SN Slot No. eNodeB
RMV DEVIP
LST DEVIP
ADD DEVIP
RMV DEVIP
DEVIP SBT Subboard Type eNodeB
DSP DEVIP
LST DEVIP
ADD DEVIP
RMV DEVIP
DEVIP PT Port Type eNodeB
DSP DEVIP
LST DEVIP
ADD DEVIP
RMV DEVIP
DEVIP PN Port No. eNodeB
DSP DEVIP
LST DEVIP
ADD DEVIP
RMV DEVIP
DEVIP IP IP Address eNodeB
DSP DEVIP
LST DEVIP
ADD DEVIP
DEVIP MASK Mask eNodeB DSP DEVIP
LST DEVIP
ADD DEVIP6
DSP DEVIP6
DEVIP6 ITFIDX Interface Index eNodeB
RMV DEVIP6
LST DEVIP6
ADD DEVIP6
RMV DEVIP6
DEVIP6 IPV6 IPv6 Address eNodeB
DSP DEVIP6
LST DEVIP6
ADD DEVIP6
DEVIP6 PFXLEN Prefix Length eNodeB DSP DEVIP6
LST DEVIP6
DEVIP6 AddressStatus Address Status eNodeB DSP DEVIP6
DEVIP6 ValidLifetime Valid Lifetime eNodeB DSP DEVIP6

DEVIP6 PreferredLifetime Preferred Lifetime eNodeB DSP DEVIP6
SET
DHCPRELAYSWIT
CH
DHCPRELAYSWITC ES DHCP Relay Switch eNodeB
LST
DHCPRELAYSWIT
CH
ADD DHCPSVRIP
DHCP Server IP
DHCPSVRIP DHCPSVRIP eNodeB RMV DHCPSVRIP
Address
LST DHCPSVRIP
OMCH Auto-
SET DHCPSW
DHCPSW SWITCH Establishment eNodeB
LST DHCPSW
Switch
SET DIFPRI
DIFPRI PRIRULE Priority Rule eNodeB
LST DIFPRI
SET DIFPRI
DIFPRI SIGPRI Signaling Priority eNodeB
LST DIFPRI
SET DIFPRI
DIFPRI OMHIGHPRI OM High Priority eNodeB
LST DIFPRI
SET DIFPRI
DIFPRI OMLOWPRI OM Low Priority eNodeB
LST DIFPRI
SET DIFPRI
DIFPRI PTPPRI IPClock Priority eNodeB
LST DIFPRI
SET DIFPRI
DIFPRI DT1PRI User Data 1 Priority eNodeB
LST DIFPRI
User Data 1
SET DIFPRI
DIFPRI DT1TYPE Primary Transport eNodeB
LST DIFPRI
Resource Type
User Data 1
SET DIFPRI
DIFPRI DT1PRIMTH Primary Port Load eNodeB
LST DIFPRI
Threshold
User Data 1
Primary To
DT1PRIMTOSECR SET DIFPRI
DIFPRI Secondary Port eNodeB
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 2
SET DIFPRI
LST DIFPRI
Resource Type
User Data 2
SET DIFPRI
LST DIFPRI
Threshold
User Data 2
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 3
SET DIFPRI
LST DIFPRI
Resource Type
User Data 3
SET DIFPRI
LST DIFPRI
Threshold
User Data 3
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 4
SET DIFPRI
LST DIFPRI
Resource Type
User Data 4
SET DIFPRI
LST DIFPRI
Threshold
User Data 4
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 5
SET DIFPRI
LST DIFPRI
Resource Type
User Data 5
SET DIFPRI
LST DIFPRI
Threshold
User Data 5
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 6
SET DIFPRI
LST DIFPRI
Resource Type
User Data 6
SET DIFPRI
LST DIFPRI
Threshold
User Data 6
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 7
SET DIFPRI
LST DIFPRI
Resource Type
User Data 7
SET DIFPRI
LST DIFPRI
Threshold
User Data 7
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 8
SET DIFPRI
LST DIFPRI
Resource Type
User Data 8
SET DIFPRI
LST DIFPRI
Threshold
User Data 8
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
SET DIFPRI
LST DIFPRI
User Data 9
SET DIFPRI
LST DIFPRI
Resource Type
User Data 9
SET DIFPRI
LST DIFPRI
Threshold
User Data 9
Primary To
ATIOTH LST DIFPRI
Load Ratio
Threshold
Bit Congestion
SET DLITFCALG
DLITFCALG BCDLITFCSW Down Link Internal eNodeB
LST DLITFCALG
Flow Control Switch
Packet Congestion
SET DLITFCALG
DLITFCALG PCDLITFCSW Down Link Internal eNodeB
LST DLITFCALG
Flow Control Switch
ACT DOT1X
DEA DOT1X
DOT1X CN Cabinet No. eNodeB
DSP DOT1X
LST DOT1X
ACT DOT1X
DEA DOT1X
DOT1X SRN Subrack No. eNodeB
DSP DOT1X
LST DOT1X
ACT DOT1X
DEA DOT1X
DOT1X SN Slot No. eNodeB
DSP DOT1X
LST DOT1X
ACT DOT1X
DEA DOT1X
DOT1X SBT Subboard Type eNodeB
DSP DOT1X
LST DOT1X
ACT DOT1X
DEA DOT1X
DOT1X PN Port No. eNodeB
DSP DOT1X
LST DOT1X
ACT DOT1X
DOT1X AM Authentic Method eNodeB DSP DOT1X
LST DOT1X
Abnormal Packet
DOT1X APN eNodeB DSP DOT1X
Number
DOT1X AFN Fail Number eNodeB DSP DOT1X
DOT1X AFR Fail Reason eNodeB DSP DOT1X
Receive EAP
DOT1X RPN eNodeB DSP DOT1X
Packet Number
DOT1X AR Authentic State eNodeB DSP DOT1X
Send EAP Packet

DOT1X SPN eNodeB DSP DOT1X
Number
Authentic Succeed
DOT1X ASN eNodeB DSP DOT1X
Number
DSP DSCPMAP
Differentiated
DSCPMAP DSCP eNodeB LST DSCPMAP
Service Codepoint
SET DSCPMAP
SET DSCPMAP
DSCPMAP VLANPRIO VLAN Priority eNodeB DSP DSCPMAP
LST DSCPMAP
ADD E1T1
DSP E1T1
E1T1 CN Cabinet No. eNodeB RMV E1T1
SET E1T1
LST E1T1
ADD E1T1
DSP E1T1
E1T1 SRN Subrack No. eNodeB RMV E1T1
SET E1T1
LST E1T1
ADD E1T1
DSP E1T1
E1T1 SN Slot No. eNodeB RMV E1T1
SET E1T1
LST E1T1
ADD E1T1
DSP E1T1
E1T1 PN Port No. eNodeB RMV E1T1
SET E1T1
LST E1T1
ADD E1T1
DSP E1T1
E1T1 PS Port Selection eNodeB RMV E1T1
SET E1T1
LST E1T1
ADD E1T1
E1T1 WORKMODE Work Mode eNodeB SET E1T1
LST E1T1
ADD E1T1
E1T1 FRAME Frame Format eNodeB SET E1T1
LST E1T1
ADD E1T1
E1T1 LNCODE Line Code eNodeB SET E1T1
LST E1T1
ADD E1T1
SET E1T1
E1T1 CLKM Clock Mode eNodeB
DSP E1T1
LST E1T1
Link Running
E1T1 LinkRunningStatus eNodeB DSP E1T1
Status
ExecuteLinkTestFla Link Test Execution

E1T1 eNodeB DSP E1T1
g Status
E1T1 UsedFlag Used Flag eNodeB DSP E1T1
E1T1 LoopLeftTime Loop Left Time eNodeB DSP E1T1
ADD E1T1
DSP E1T1
E1T1 SBT Subboard Type eNodeB RMV E1T1
SET E1T1
LST E1T1
DSP DHCPRSLT
E1T1 ActualWorkMode Actual Work Mode eNodeB
DSP E1T1
Actual Frame DSP DHCPRSLT

E1T1 ActualFrameFormat eNodeB
Format DSP E1T1
DSP DHCPRSLT
E1T1 ActualLineCode Actual Line Code eNodeB
DSP E1T1
E1/T1 BER SET E1T1BER

E1T1BER BTL eNodeB
Threshold Level LST E1T1BER
ACT ETHOAM3AH
DEA ETHOAM3AH
ETHOAM3AH CN Cabinet No. eNodeB
DSP ETHOAM3AH
LST ETHOAM3AH
ACT ETHOAM3AH
DEA ETHOAM3AH
ETHOAM3AH SRN Subrack No. eNodeB
DSP ETHOAM3AH
LST ETHOAM3AH
ACT ETHOAM3AH
DEA ETHOAM3AH
ETHOAM3AH SN Slot No. eNodeB
DSP ETHOAM3AH
LST ETHOAM3AH
ACT ETHOAM3AH
DEA ETHOAM3AH
ETHOAM3AH SBT Subboard Type eNodeB
DSP ETHOAM3AH
LST ETHOAM3AH
ACT ETHOAM3AH
DEA ETHOAM3AH
ETHOAM3AH PT Port Type eNodeB
DSP ETHOAM3AH
LST ETHOAM3AH
ACT ETHOAM3AH
DEA ETHOAM3AH
ETHOAM3AH PN Port No. eNodeB
DSP ETHOAM3AH
LST ETHOAM3AH
ACT ETHOAM3AH
ETHOAM3AH WORKMODE Working Mode eNodeB
LST ETHOAM3AH
ACT ETHOAM3AH
ETHOAM3AH DTPRD Detection Period eNodeB
LST ETHOAM3AH
ACT ETHOAM3AH
ETHOAM3AH PDUSIZE PDU Size eNodeB
LST ETHOAM3AH
ACT ETHOAM3AH
ETHOAM3AH RMTLBFLG Loopback Flag eNodeB
LST ETHOAM3AH
ACT ETHOAM3AH
ETHOAM3AH FLTINDFLG Fault Report Flag eNodeB
LST ETHOAM3AH
Error Frame Event ACT ETHOAM3AH

ETHOAM3AH ERRFRMEVTPRD eNodeB
Duration LST ETHOAM3AH
Error Frame Event ACT ETHOAM3AH

ETHOAM3AH ERRFRMEVTTHD eNodeB
Threshold LST ETHOAM3AH
Error Frame
ERRFRMSCDEVT ACT ETHOAM3AH
ETHOAM3AH Seconds Summary eNodeB
PRD LST ETHOAM3AH
Event Duration
Error Frame
ERRFRMSCDEVTT ACT ETHOAM3AH
ETHOAM3AH Seconds Summary eNodeB
HD LST ETHOAM3AH
Event Threshold
ETHOAM3AH FSMState Current State eNodeB DSP ETHOAM3AH
Number of RX
RxDropOAMPDUC
ETHOAM3AH Dropped eNodeB DSP ETHOAM3AH
ount
OAMPDUs
RxEventOAMPDUC Number of RX
ETHOAM3AH eNodeB DSP ETHOAM3AH
ount Event OAMPDUs
RxFaultOAMPDUC Number of RX Fault

ount OAMPDUs
Number of RX
RxInfoOAMPDUCo
ETHOAM3AH Information eNodeB DSP ETHOAM3AH
unt
OAMPDUs
Number of RX
RxLoopbackOAMP
ETHOAM3AH Loopback Control eNodeB DSP ETHOAM3AH
DUCount
OAMPDUs
RxTotalOAMPDUC Total Number of RX

ount OAMPDUs
Number of TX
TxDropOAMPDUCo
ETHOAM3AH Dropped eNodeB DSP ETHOAM3AH
unt
OAMPDUs
TxEventOAMPDUC Number of TX
ount Event OAMPDUs
TxFaultOAMPDUC Number of TX Fault

ount OAMPDUs
Number of TX
TxInfoOAMPDUCo
ETHOAM3AH Information eNodeB DSP ETHOAM3AH
unt
OAMPDUs
Number of TX
TxLoopbackOAMP
ETHOAM3AH Loopback Control eNodeB DSP ETHOAM3AH
DUCount
OAMPDUs
TxTotalOAMPDUCo Total Number of TX
unt OAMPDUs
ADD ETHPORT
DSP ETHPORT
RMV ETHPORT
ETHPORT CN Cabinet No. eNodeB
RST ETHPORT
SET ETHPORT
LST ETHPORT
ADD ETHPORT
DSP ETHPORT
RMV ETHPORT
ETHPORT SRN Subrack No. eNodeB
RST ETHPORT
SET ETHPORT
LST ETHPORT
ADD ETHPORT
DSP ETHPORT
RMV ETHPORT
ETHPORT SN Slot No. eNodeB
RST ETHPORT
SET ETHPORT
LST ETHPORT
ADD ETHPORT
DSP ETHPORT
RMV ETHPORT
ETHPORT SBT Subboard Type eNodeB
RST ETHPORT
SET ETHPORT
LST ETHPORT
ADD ETHPORT
DSP ETHPORT
RMV ETHPORT
ETHPORT PN Port No. eNodeB
RST ETHPORT
SET ETHPORT
LST ETHPORT
ADD ETHPORT
SET ETHPORT
ETHPORT PA Port Attribute eNodeB DSP DHCPRSLT
DSP ETHPORT
LST ETHPORT
ADD ETHPORT
Maximum SET ETHPORT
ETHPORT MTU eNodeB
Transmission Unit DSP ETHPORT
LST ETHPORT
ADD ETHPORT
SET ETHPORT
ETHPORT SPEED Speed eNodeB
DSP DHCPRSLT
LST ETHPORT
ADD ETHPORT
SET ETHPORT
ETHPORT DUPLEX Duplex eNodeB
DSP DHCPRSLT
LST ETHPORT
ADD ETHPORT
SET ETHPORT
ETHPORT ARPPROXY ARP Proxy eNodeB
DSP ETHPORT
LST ETHPORT
ADD ETHPORT
SET ETHPORT
ETHPORT FC Flow Control eNodeB
DSP ETHPORT
LST ETHPORT
MAC Frame Error ADD ETHPORT

ETHPORT FERAT Rate Occur eNodeB SET ETHPORT
Threshold LST ETHPORT
MAC Frame Error ADD ETHPORT

ETHPORT FERDT Rate Clear eNodeB SET ETHPORT
Threshold LST ETHPORT
ETHPORT MAC MAC Address eNodeB DSP ETHPORT

ETHPORT PortStatus Port Status eNodeB DSP ETHPORT
ETHPORT LoopbackStatus Loopback Status eNodeB DSP ETHPORT
InLoopbackTestMo In Loopback Mode

ETHPORT eNodeB DSP ETHPORT
de or Not
OAM3AHEnableFla Ethernet OAM 3AH

ETHPORT eNodeB DSP ETHPORT
g Flag
Number of RX
ETHPORT RxPackets eNodeB DSP ETHPORT
Packets
Number of RX
ETHPORT RxBytes eNodeB DSP ETHPORT
Bytes
Number of RX CRC
ETHPORT RxCRCError eNodeB DSP ETHPORT
Error Packets
ETHPORT RxFlowRate RX Traffic eNodeB DSP ETHPORT
Number of TX
ETHPORT TxPackets eNodeB DSP ETHPORT
Packets
Number of TX
ETHPORT TxBytes eNodeB DSP ETHPORT
Bytes
ETHPORT TxFlowRate TX Traffic eNodeB DSP ETHPORT
ETHPORT IPNum Number of IPs eNodeB DSP ETHPORT
ETHPORT IPList IP Address List eNodeB DSP ETHPORT
Local Configuration
ETHPORT LocCfgNegoMode eNodeB DSP ETHPORT
Negotiation Mode
Local Actual
ETHPORT LocRealNegoMode eNodeB DSP ETHPORT
Negotiation Mode
ETHPORT LocSpeed Local Speed eNodeB DSP ETHPORT
ETHPORT LocDuplex Local Duplex eNodeB DSP ETHPORT
Peer Actual
ETHPORT PeerNegoMode eNodeB DSP ETHPORT
Negotiation Mode
ETHPORT PeerSpeed Peer Speed eNodeB DSP ETHPORT
ETHPORT PeerDuplex Peer Duplex eNodeB DSP ETHPORT
Physical Layer
ETHPORT PhyLayerStat eNodeB DSP ETHPORT
Status
ADD ETHTRK
DSP ETHTRK
ETHTRK CN Cabinet No. eNodeB MOD ETHTRK
RMV ETHTRK
LST ETHTRK
ADD ETHTRK
DSP ETHTRK
ETHTRK SRN Subrack No. eNodeB MOD ETHTRK
RMV ETHTRK
LST ETHTRK
ADD ETHTRK
DSP ETHTRK
ETHTRK SN Slot No. eNodeB MOD ETHTRK
RMV ETHTRK
LST ETHTRK
ADD ETHTRK
DSP ETHTRK
ETHTRK TN Trunk No. eNodeB MOD ETHTRK
RMV ETHTRK
LST ETHTRK
ADD ETHTRK
MOD ETHTRK
ETHTRK LACP Trunk Type eNodeB DSP DHCPRSLT
DSP ETHTRK
LST ETHTRK
ADD ETHTRK
MOD ETHTRK
ETHTRK ARPPROXY ARP Proxy eNodeB
DSP ETHTRK
LST ETHTRK
ADD ETHTRK
DSP ETHTRK
ETHTRK SBT Subboard Type eNodeB MOD ETHTRK
RMV ETHTRK
LST ETHTRK
ADD ETHTRK
Max Transmission MOD ETHTRK
ETHTRK MTU eNodeB
Unit DSP ETHTRK
LST ETHTRK
Ethernet Trunk
ETHTRK EthTrunkStatus eNodeB DSP ETHTRK
Status
ETHTRK LocalMAC Local MAC Address eNodeB DSP ETHTRK

Peer System MAC
ETHTRK PeerSysMAC eNodeB DSP ETHTRK
Address
Number of Ethernet
ETHTRK EthTrunkLinkNum eNodeB DSP ETHTRK
Trunk Ports
Ethernet Trunk Port DSP ETHTRK

ETHTRK EthTrunkLinkIDs eNodeB
No. LST ETHTRK
EthTrunkLinkUpNu Number of Active

ETHTRK eNodeB DSP ETHTRK
m Trunk Ports
Active Trunk Port

ETHTRK EthTrunkLinkUpIDs eNodeB DSP ETHTRK
No.
Number of RX
ETHTRK RxPackets eNodeB DSP ETHTRK
Packets
Number of RX
ETHTRK RxBytes eNodeB DSP ETHTRK
Bytes
Number of RX
ETHTRK RxDroppedPackets eNodeB DSP ETHTRK
Dropped Packets
Number of RX
ETHTRK RxDroppedBytes eNodeB DSP ETHTRK
Dropped Bytes
Number of TX
ETHTRK TxPackets eNodeB DSP ETHTRK
Packets
Number of TX
ETHTRK TxBytes eNodeB DSP ETHTRK
Bytes
Number of TX
ETHTRK TxDroppedPackets eNodeB DSP ETHTRK
Dropped Packets
Number of TX
ETHTRK TxDroppedBytes eNodeB DSP ETHTRK
Dropped Bytes
ETHTRK IPNum Number of IPs eNodeB DSP ETHTRK
ETHTRK IPList IP Address List eNodeB DSP ETHTRK
ADD ETHTRKLNK
DSP ETHTRKLNK
ETHTRKLNK CN Cabinet No. eNodeB
RMV ETHTRKLNK
LST ETHTRKLNK
ADD ETHTRKLNK
DSP ETHTRKLNK
ETHTRKLNK SRN Subrack No. eNodeB
RMV ETHTRKLNK
LST ETHTRKLNK
ADD ETHTRKLNK
DSP ETHTRKLNK
ETHTRKLNK SN Slot No. eNodeB
RMV ETHTRKLNK
LST ETHTRKLNK
ADD ETHTRKLNK
DSP ETHTRKLNK
ETHTRKLNK TN Trunk No. eNodeB
RMV ETHTRKLNK
LST ETHTRKLNK
ADD ETHTRKLNK
DSP ETHTRKLNK
ETHTRKLNK PN Ethernet Port No. eNodeB
RMV ETHTRKLNK
LST ETHTRKLNK
ADD ETHTRKLNK
ETHTRKLNK PRI Port Priority eNodeB DSP ETHTRKLNK
LST ETHTRKLNK
ADD ETHTRKLNK
ETHTRKLNK FLAG Master Flag eNodeB
LST ETHTRKLNK
ADD ETHTRKLNK
DSP ETHTRKLNK
ETHTRKLNK SBT Subboard Type eNodeB
RMV ETHTRKLNK
LST ETHTRKLNK
ETHTRKLNK PortStatus Port Status eNodeB DSP ETHTRKLNK

ETHTRKLNK MAC MAC Address eNodeB DSP ETHTRKLNK
Local Timeout
ETHTRKLNK LocalTimeoutMode eNodeB DSP ETHTRKLNK
Mode
ETHTRKLNK PeerTimeoutMode Peer Timeout Mode eNodeB DSP ETHTRKLNK
Number of RX
ETHTRKLNK RxLACPPackets eNodeB DSP ETHTRKLNK
LACP Packets
Number of TX
ETHTRKLNK TxLACPPackets eNodeB DSP ETHTRKLNK
LACP Packets
ADD EXTUDT
User Data Type MOD EXTUDT
EXTUDT EXTUDTNO eNodeB
Number RMV EXTUDT
LST EXTUDT
Extern User Data

ADD EXTUDT
EXTUDTPARAGRP Type Transfer
EXTUDT eNodeB MOD EXTUDT
ID Parameter Group
LST EXTUDT
ID.
ADD
EXTUDTPARAGRP
Extern User Data LST
EXTUDTPARAGRP Type Transfer EXTUDTPARAGRP
EXTUDTPARAGRP eNodeB
ID Parameter Group MOD
ID. EXTUDTPARAGRP
RMV
EXTUDTPARAGRP
ADD
EXTUDTPARAGRP
MOD
EXTUDTPARAGRP PRI Priority eNodeB
EXTUDTPARAGRP
LST
EXTUDTPARAGRP
ADD
EXTUDTPARAGRP
MOD
EXTUDTPARAGRP ACTFACTOR Act Factor eNodeB
EXTUDTPARAGRP
LST
EXTUDTPARAGRP
ADD
EXTUDTPARAGRP
PRIMTRANRSCTY Primary Transport MOD
PE Resource Type EXTUDTPARAGRP
LST
EXTUDTPARAGRP
ADD
EXTUDTPARAGRP
Primary Port Load MOD
EXTUDTPARAGRP PRIMPTLOADTH eNodeB
Threshold EXTUDTPARAGRP
LST
EXTUDTPARAGRP
ADD
Primary To EXTUDTPARAGRP
PRIM2SECPTLOA Secondary Port MOD
DRATH Load Ratio EXTUDTPARAGRP
Threshold LST
EXTUDTPARAGRP
ADD
FLOODDEFEND
DSP
FLOODDEFEND
MOD
FLOODDEFEND FLDTYPE Flood Type eNodeB
FLOODDEFEND
RMV
FLOODDEFEND
LST
FLOODDEFEND
ADD
FLOODDEFEND
MOD
FLOODDEFEND DFDSW Defend Switch eNodeB
FLOODDEFEND
LST
FLOODDEFEND
ADD
FLOODDEFEND
MOD
FLOODDEFEND DFDTHD Defend Threshold eNodeB
FLOODDEFEND
LST
FLOODDEFEND
ADD
FLOODDEFEND
MOD
FLOODDEFEND ALMSW Alarm Switch eNodeB
FLOODDEFEND
LST
FLOODDEFEND
ADD
FLOODDEFEND
MOD
FLOODDEFEND ALMTHD Alarm Threshold eNodeB
FLOODDEFEND
LST
FLOODDEFEND
Number of Flood DSP

FLOODDEFEND Packets eNodeB
Droped Packets FLOODDEFEND
Receive Total DSP

FLOODDEFEND RcvTotalPkt eNodeB
packets FLOODDEFEND
Resource Group SET
GTRANSPARA LPSCHSW Scheduling Weight eNodeB GTRANSPARA
Switch LST GTRANSPARA
SET
GTRANSPARA RATECFGTYPE Rate Config Type eNodeB GTRANSPARA
LST GTRANSPARA
SET
GTRANSPARA SBTIME Switch Back Time eNodeB GTRANSPARA
LST GTRANSPARA
SET
GTRANSPARA ARPAGINGTIME ARP Aging Time eNodeB GTRANSPARA
LST GTRANSPARA
SET IKECFG
IKECFG IKELNM Local Name eNodeB DSP IKECFG
LST IKECFG
SET IKECFG
IKECFG IKEKLI Keepalive Interval eNodeB DSP IKECFG
LST IKECFG
SET IKECFG
IKECFG IKEKLT Keepalive Timeout eNodeB DSP IKECFG
LST IKECFG
SET IKECFG
IKECFG DSCP DSCP eNodeB DSP IKECFG
LST IKECFG
IKECFG CabinetNo Cabinet No. eNodeB DSP IKECFG
IKECFG SubrackNo Subrack No. eNodeB DSP IKECFG
IKECFG SlotNo Slot No. eNodeB DSP IKECFG

ADD IKEPEER
DSP IKEPEER
IKEPEER PEERNAME IKE Peer Name eNodeB LST IKEPEER
MOD IKEPEER
RMV IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER PROPID IKE Proposal ID eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER IKEVERSION Version eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER EXCHMODE Exchange Mode eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER IDTYPE Local ID Type eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER REMOTEIP Remote IP Address eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER REMOTENAME Remote Name eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER PKEY Pre-shared Key eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER DPD DPD Mode eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER DPDIDLETIME DPD Idle Time eNodeB
DSP IKEPEER
LST IKEPEER
ADD IKEPEER
DPD
MOD IKEPEER
IKEPEER DPDRETRI Retransmission eNodeB
DSP IKEPEER
Interval
LST IKEPEER
ADD IKEPEER
DPD
MOD IKEPEER
IKEPEER DPDRETRN Retransmission eNodeB
DSP IKEPEER
Count
LST IKEPEER
ADD IKEPEER
MOD IKEPEER
IKEPEER LOCALIP Local IP Address eNodeB
DSP IKEPEER
LST IKEPEER
IKEPEER CabinetNo Cabinet No. eNodeB DSP IKEPEER
IKEPEER SubrackNo Subrack No. eNodeB DSP IKEPEER
IKEPEER SlotNo Slot No. eNodeB DSP IKEPEER

ADD IKEPEER6
DSP IKEPEER6
IPv6 IKE Peer
IKEPEER6 PEERNAME eNodeB LST IKEPEER6
Name
MOD IKEPEER6
RMV IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 PROPID IKE Proposal ID eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 IKEVERSION Version eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 EXCHMODE Exchange Mode eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 IDTYPE Local ID Type eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
Remote IPv6 MOD IKEPEER6
IKEPEER6 REMOTEIP eNodeB
Address DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 REMOTENAME Remote Name eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 PKEY Pre-shared Key eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 DPD DPD Mode eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 DPDIDLETIME DPD Idle Time eNodeB
DSP IKEPEER6
LST IKEPEER6
ADD IKEPEER6
DPD
MOD IKEPEER6
IKEPEER6 DPDRETRI Retransmission eNodeB
DSP IKEPEER6
Interval
LST IKEPEER6
ADD IKEPEER6
DPD
MOD IKEPEER6
IKEPEER6 DPDRETRN Retransmission eNodeB
DSP IKEPEER6
Count
LST IKEPEER6
ADD IKEPEER6
MOD IKEPEER6
IKEPEER6 LOCALIP Local IPv6 Address eNodeB
DSP IKEPEER6
LST IKEPEER6
IKEPEER6 CabinetNo Cabinet No. eNodeB DSP IKEPEER6
IKEPEER6 SubrackNo Subrack No. eNodeB DSP IKEPEER6
IKEPEER6 SlotNo Slot No. eNodeB DSP IKEPEER6

ADD
IKEPROPOSAL
DSP
IKEPROPOSAL
LST
IKEPROPOSAL PROPID Proposal ID eNodeB
IKEPROPOSAL
MOD
IKEPROPOSAL
RMV
IKEPROPOSAL
ADD
IKEPROPOSAL
MOD
Encryption IKEPROPOSAL
IKEPROPOSAL ENCALG eNodeB
Algorithm DSP
IKEPROPOSAL
LST
IKEPROPOSAL
ADD
IKEPROPOSAL
MOD
Authentication IKEPROPOSAL
IKEPROPOSAL AUTHALG eNodeB
Algorithm DSP
IKEPROPOSAL
LST
IKEPROPOSAL
ADD
IKEPROPOSAL
MOD
Authentication IKEPROPOSAL
IKEPROPOSAL AUTHMETH eNodeB
Method DSP
IKEPROPOSAL
LST
IKEPROPOSAL
ADD
IKEPROPOSAL
MOD
Diffie-Hellman IKEPROPOSAL
IKEPROPOSAL DHGRP eNodeB
Group DSP
IKEPROPOSAL
LST
IKEPROPOSAL
ADD
IKEPROPOSAL
MOD
ISAKMP SA IKEPROPOSAL
IKEPROPOSAL DURATION eNodeB
Duration DSP
IKEPROPOSAL
LST
IKEPROPOSAL
ADD
IKEPROPOSAL
MOD
IKEPROPOSAL
IKEPROPOSAL PRFALG PRF Algorithm eNodeB
DSP
IKEPROPOSAL
LST
IKEPROPOSAL
DSP
IKEPROPOSAL CabinetNo Cabinet No. eNodeB
IKEPROPOSAL
DSP
IKEPROPOSAL SubrackNo Subrack No. eNodeB
IKEPROPOSAL
DSP
IKEPROPOSAL SlotNo Slot No. eNodeB
IKEPROPOSAL
ADD IP2RSCGRP
IP2RSCGRP CN Cabinet No. eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP SRN Subrack No. eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP SN Slot No. eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ADD IP2RSCGRP
Transmission
IP2RSCGRP RSCGRPID eNodeB RMV IP2RSCGRP
Resource Group ID
LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP DSTIP Destination IP eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP DSTMASK Mask eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
Transmission ADD IP2RSCGRP

IP2RSCGRP BEAR Resource Group eNodeB RMV IP2RSCGRP
Bear Type LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP SBT Subboard Type eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP PT Bearing Port Type eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ADD IP2RSCGRP
IP2RSCGRP PN Bearing Port No. eNodeB RMV IP2RSCGRP
LST IP2RSCGRP
ARPSPOOFCHKS ARP Spoofing SET IPGUARD

IPGUARD eNodeB
W Check Switch LST IPGUARD
ARPSPOOFALMTH ARP Spoofing SET IPGUARD
IPGUARD eNodeB
D Alarm Threshold LST IPGUARD
ARPLRNSTRICTS ARP Learning Strict SET IPGUARD

IPGUARD eNodeB
W Switch LST IPGUARD
INVALIDPKTCHKS Invalid Packet SET IPGUARD
IPGUARD eNodeB
W Check Switch LST IPGUARD
INVALIDPKTALMT SET IPGUARD

IPGUARD Alarm Threshold eNodeB
HD LST IPGUARD
IPSECREPLAYCH IPSec Replay Alarm SET IPGUARD

IPGUARD eNodeB
KSW Switch LST IPGUARD
IPSECREPLAYALM IPSec Replay Alarm SET IPGUARD
IPGUARD eNodeB
THD Threshold LST IPGUARD
DSP
IPGUARD PT Port Type eNodeB
INVALIDPKTINFO
DSP
IPGUARD PN Port No. eNodeB
INVALIDPKTINFO
Source MAC
DSP
IPGUARD SrcMacAddr Address of Invalid eNodeB
INVALIDPKTINFO
Packet
Destination MAC
DSP
IPGUARD DstMacAddr Address of Invalid eNodeB
INVALIDPKTINFO
Packet
VLAN ID of Invalid DSP

IPGUARD VlanID eNodeB
Packet INVALIDPKTINFO
Protocol Type of DSP

IPGUARD MacLayerProtocol eNodeB
MAC Layer INVALIDPKTINFO
Source IP Address DSP

IPGUARD SrcIP eNodeB
of Invalid Packet INVALIDPKTINFO
Destination IP
DSP
IPGUARD DstIP Address of Invalid eNodeB
INVALIDPKTINFO
Packet
Protocol Type of IP DSP

IPGUARD IPLayerProtocol eNodeB
Layer INVALIDPKTINFO
Source Port of DSP
IPGUARD SrcPort eNodeB
Invalid Packet INVALIDPKTINFO
Destination Port of DSP

IPGUARD DstPort eNodeB
Invalid Packet INVALIDPKTINFO
DSP
IPGUARD PacketData Invalid Packet Data eNodeB
INVALIDPKTINFO
ADD IPITF6
DSP IPITF6
IPITF6 ITFIDX Interface Index eNodeB
RMV IPITF6
LST IPITF6
ADD IPITF6
IPITF6 ITFTYPE Interface Type eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 CN Cabinet No. eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 SRN Subrack No. eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 SN Slot No. eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 SBT Subboard Type eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 PT Port Type eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 PN Port No. eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
IPITF6 VLANID VLAN ID eNodeB DSP IPITF6
LST IPITF6
ADD IPITF6
Maximum
IPITF6 MTU eNodeB DSP IPITF6
Transmission Unit
LST IPITF6
IPITF6 ItfStatus Interface Status eNodeB DSP IPITF6
IPITF6 LinkLocalAddr Link Local Address eNodeB DSP IPITF6
Global Unicast
IPITF6 GlobalAddrNum eNodeB DSP IPITF6
Address Number
Global Unicast
IPITF6 GlobalAddr eNodeB DSP IPITF6
Address(es)
Multicast Address
IPITF6 MulticastAddrNum eNodeB DSP IPITF6
Number
Multicast
IPITF6 MulticastAddr eNodeB DSP IPITF6
Address(es)
NDAddrConfictChe
IPITF6 ND DAD eNodeB DSP IPITF6
ck
ND DAD Attempts
IPITF6 NDAttempts eNodeB DSP IPITF6
Number
IPITF6 NDReachableTime ND Reachable Time eNodeB DSP IPITF6
ND Retransmit
IPITF6 NDRetransInterval eNodeB DSP IPITF6
Interval
LinkLocalAddrAuto Link Local Address

IPITF6 eNodeB DSP IPITF6
Config Autoconfig
StatelessAutoConfi Stateless
IPITF6 eNodeB DSP IPITF6
g Autoconfig
ADD IPPATH
DSP IPPATH
IPPATH PATHID IP Path ID eNodeB LST IPPATH
MOD IPPATH
RMV IPPATH
ADD IPPATH
IPPATH CN Cabinet No. eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH SRN Subrack No. eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH SN Slot No. eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH PT Port Type eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH PN Port No. eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH PATHTYPE Path Type eNodeB
LST IPPATH
ADD IPPATH
IPPATH DSCP DSCP eNodeB
LST IPPATH
ADD IPPATH
IPPATH LOCALIP Local IP eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH PEERIP Peer IP eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH ANI Adjacent Node ID eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
Transport Resource MOD IPPATH
IPPATH QT eNodeB
Type DSP IPPATH
LST IPPATH
ADD IPPATH
IPPATH APPTYPE Application Type eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH PATHCHK Path Check eNodeB MOD IPPATH
LST IPPATH
RealtimeTxBandwid Realtime TX
IPPATH eNodeB DSP IPPATH
th Bandwidth
RealtimeRxBandwi Realtime RX
dth Bandwidth
NonRealtimeTxBan Non-Realtime TX
dwidth Bandwidth
NonRealtimeRxBan Non-Realtime RX
dwidth Bandwidth
Non-Realtime
NonRealtimeReserv
IPPATH Reserved TX eNodeB DSP IPPATH
edTxBandwidth
Bandwidth
Non-Realtime
NonRealtimeReserv
IPPATH Reserved RX eNodeB DSP IPPATH
edRxBandwidth
Bandwidth
IP Path Check
IPPATH IppathCheckResult eNodeB DSP IPPATH
Result
ADD IPPATH
Transmission
IPPATH RSCGRPID eNodeB MOD IPPATH
Resource Group ID
LST IPPATH
ADD IPPATH
IPPATH DESCRI Description Info eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
IPPATH SBT Subboard Type eNodeB MOD IPPATH
LST IPPATH
ADD IPPATH
Join Transmission
IPPATH JNRSCGRP eNodeB MOD IPPATH
Resource Group
LST IPPATH
ADD IPPATH6
DSP IPPATH6
IPPATH6 PATHID IPv6 Path ID eNodeB MOD IPPATH6
RMV IPPATH6
LST IPPATH6
Join Transmission ADD IPPATH6

IPPATH6 JNRSCGRP eNodeB
Resource Group LST IPPATH6
Transmission ADD IPPATH6

IPPATH6 RSCGRPID eNodeB
Resource Group ID LST IPPATH6
ADD IPPATH6
IPPATH6 ITFIDX Interface Index eNodeB
LST IPPATH6
ADD IPPATH6
IPPATH6 PATHTYPE Path Type eNodeB
LST IPPATH6
ADD IPPATH6
IPPATH6 DSCP DSCP eNodeB
LST IPPATH6
ADD IPPATH6
IPPATH6 LOCALIP6 Local IPv6 Address eNodeB
LST IPPATH6
ADD IPPATH6
IPPATH6 PEERIP6 Peer IPv6 Address eNodeB
LST IPPATH6
ADD IPPATH6
IPPATH6 ANI Adjacent Node ID eNodeB MOD IPPATH6
LST IPPATH6
ADD IPPATH6
IPPATH6 APPTYPE Application Type eNodeB MOD IPPATH6
LST IPPATH6
ADD IPPATH6
IPPATH6 PATHCHK Path Check eNodeB MOD IPPATH6
LST IPPATH6
RealtimeTxBandwid Realtime TX
IPPATH6 eNodeB DSP IPPATH6
th Bandwidth
RealtimeRxBandwi Realtime RX
dth Bandwidth
NonRealtimeTxBan Non-Realtime TX
dwidth Bandwidth
NonRealtimeRxBan Non-Realtime RX
dwidth Bandwidth
Non-Realtime
NonRealtimeReserv
IPPATH6 Reserved TX eNodeB DSP IPPATH6
edTxBandwidth
Bandwidth
Non-Realtime
NonRealtimeReserv
IPPATH6 Reserved RX eNodeB DSP IPPATH6
edRxBandwidth
Bandwidth
IPv6 Path Check

IPPATH6 IppathCheckResult eNodeB DSP IPPATH6
Result
ADD IPPATH6
IPPATH6 DESCRI Description Info eNodeB MOD IPPATH6
LST IPPATH6
ADD IPPATHRT
DSP IPPATHRT
IPPATHRT SRCIP Source IP eNodeB
RMV IPPATHRT
LST IPPATHRT
ADD IPPATHRT
DSP IPPATHRT
IPPATHRT DSTIP Destination IP eNodeB
RMV IPPATHRT
LST IPPATHRT
ADD IPPATHRT
Transport Resource
IPPATHRT TRANRSCTYPE eNodeB DSP IPPATHRT
Type
LST IPPATHRT
ADD IPPATHRT
IPPATHRT NEXTHOPIP Next Hop IP eNodeB DSP IPPATHRT
LST IPPATHRT
ADD
IPPMSESSION
DSP
IPPMSESSION
IPPMSESSION IPPMSN IP PM Session ID eNodeB
RMV
IPPMSESSION
LST
IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION LOCALIP Local IP eNodeB
IPPMSESSION
LST
IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION PEERIP Peer IP eNodeB
IPPMSESSION
LST
IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION IPPMDSCP DSCP eNodeB
IPPMSESSION
LST
IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION DIR Activate Direction eNodeB
IPPMSESSION
LST
IPPMSESSION
DSP
IPPMSESSION TimeDelay Round Trip Time eNodeB
IPPMSESSION
DSP
IPPMSESSION RxJitter RX Jitter eNodeB
IPPMSESSION
DSP
IPPMSESSION TxJitter TX Jitter eNodeB
IPPMSESSION
DSP
IPPMSESSION RxLossRate RX Loss Rate eNodeB
IPPMSESSION
DSP
IPPMSESSION TxLossRate TX Loss Rate eNodeB
IPPMSESSION
DSP
IPPMSESSION IppmUpActState Activate State(Up) eNodeB
IPPMSESSION
Activate DSP
IPPMSESSION IppmDownActState eNodeB
State(Down) IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION IPPMTYPE IP PM Type eNodeB
IPPMSESSION
LST
IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION BINDPATH Bind IP Path eNodeB
IPPMSESSION
LST
IPPMSESSION
ADD
IPPMSESSION
DSP
IPPMSESSION PATHID IP Path ID eNodeB
IPPMSESSION
LST
IPPMSESSION
DLDscpChangeFla DSCP Change DSP

IPPMSESSION eNodeB
g Flag(Down) IPPMSESSION
DSCP Initial DSP

IPPMSESSION DLPreDscp eNodeB
Value(Down) IPPMSESSION
DSCP Changed DSP

IPPMSESSION DLModiDscp eNodeB
Value(Down) IPPMSESSION
DSCP Changed
DLDscpChangeDat DSP
IPPMSESSION Date And eNodeB
eTime IPPMSESSION
Time(Down)
ULDscpChangeFla DSCP Change DSP

IPPMSESSION eNodeB
g Flag(Up) IPPMSESSION
DSCP Initial DSP
IPPMSESSION ULPreDscp eNodeB
Value(Up) IPPMSESSION
DSCP Changed DSP

IPPMSESSION ULModiDscp eNodeB
Value(Up) IPPMSESSION
ULDscpChangeDat DSCP Changed DSP

IPPMSESSION eNodeB
eTime Date And Time(Up) IPPMSESSION
IP PM Protocol DSP
IPPMSESSION VER eNodeB
Version IPPMSESSION
ADD IPRT
DSP IPRT
IPRT CN Cabinet No. eNodeB MOD IPRT
RMV IPRT
LST IPRT
ADD IPRT
DSP IPRT
IPRT SRN Subrack No. eNodeB MOD IPRT
RMV IPRT
LST IPRT
ADD IPRT
DSP IPRT
IPRT SN Slot No. eNodeB MOD IPRT
RMV IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT SBT Subboard Type eNodeB
RMV IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT IFT Port Type eNodeB
RMV IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT IFNO Port No. eNodeB
RMV IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT RTTYPE Route Type eNodeB RMV IPRT
DSP IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT DSTIP Destination IP eNodeB RMV IPRT
DSP IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT DSTMASK Mask eNodeB RMV IPRT
DSP IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT NEXTHOP Next Hop IP eNodeB RMV IPRT
DSP IPRT
LST IPRT
ADD IPRT
MOD IPRT
IPRT PREF Preference eNodeB
DSP IPRT
LST IPRT
IPRT RTRouteType Protocol eNodeB DSP IPRT
ADD IPRT
IPRT DESCRI Description Info eNodeB MOD IPRT
LST IPRT
IPRT ActualPortType Actual Port Type eNodeB DSP IPRT
IPRT ActualPortNo Actual Port No. eNodeB DSP IPRT

ADD IPRT6
MOD IPRT6
Destination IPv6
IPRT6 DSTIP eNodeB RMV IPRT6
Address
DSP IPRT6
LST IPRT6
ADD IPRT6
MOD IPRT6
IPRT6 PFXLEN Prefix Length eNodeB RMV IPRT6
DSP IPRT6
LST IPRT6
ADD IPRT6
MOD IPRT6
IPRT6 RTTYPE Route Type eNodeB RMV IPRT6
DSP IPRT6
LST IPRT6
ADD IPRT6
MOD IPRT6
IPRT6 NEXTHOPIP6TYPE Next Hop IPv6 Type eNodeB
RMV IPRT6
LST IPRT6
ADD IPRT6
MOD IPRT6
Next Hop IPv6
IPRT6 NEXTHOPIP eNodeB RMV IPRT6
Address
DSP IPRT6
LST IPRT6
ADD IPRT6
MOD IPRT6
IPRT6 ITFIDX Interface Index eNodeB RMV IPRT6
DSP IPRT6
LST IPRT6
ADD IPRT6
MOD IPRT6
IPRT6 PREF Preference eNodeB
DSP IPRT6
LST IPRT6
IPRT6 RTRouteType Protocol eNodeB DSP IPRT6
ADD IPRT6
IPRT6 DESCRI Description Info eNodeB MOD IPRT6
LST IPRT6
ADD IPSECBIND
IPSECBIND CN Cabinet No. eNodeB RMV IPSECBIND
LST IPSECBIND
ADD IPSECBIND
IPSECBIND SRN Subrack No. eNodeB RMV IPSECBIND
LST IPSECBIND
ADD IPSECBIND
IPSECBIND SN Slot No. eNodeB RMV IPSECBIND
LST IPSECBIND
ADD IPSECBIND
IPSECBIND SBT Subboard Type eNodeB RMV IPSECBIND
LST IPSECBIND
ADD IPSECBIND
IPSECBIND PT Port Type eNodeB RMV IPSECBIND
LST IPSECBIND
ADD IPSECBIND
IPSECBIND PN Port No. eNodeB RMV IPSECBIND
LST IPSECBIND
ADD IPSECBIND
IPSECBIND SPGN Policy Group Name eNodeB
LST IPSECBIND
ADD IPSECBIND6
IPSECBIND6 ITFIDX Interface Index eNodeB RMV IPSECBIND6
LST IPSECBIND6
IPv6 IPSec Policy ADD IPSECBIND6

IPSECBIND6 SPGN6 eNodeB
Group Name LST IPSECBIND6
ADD IPSECDTNL
DSP IPSECDTNL
IPSec Dual Tunnel
IPSECDTNL DUALID eNodeB LST IPSECDTNL
ID
MOD IPSECDTNL
RMV IPSECDTNL
ADD IPSECDTNL
Master Policy MOD IPSECDTNL
IPSECDTNL MSPGN eNodeB
Group Name DSP IPSECDTNL
LST IPSECDTNL
ADD IPSECDTNL
Master IPSec MOD IPSECDTNL
IPSECDTNL MSPSN eNodeB
Sequence No. DSP IPSECDTNL
LST IPSECDTNL
ADD IPSECDTNL
Slave Policy Group MOD IPSECDTNL
IPSECDTNL SSPGN eNodeB
Name DSP IPSECDTNL
LST IPSECDTNL
ADD IPSECDTNL
Slave IPSec MOD IPSECDTNL
IPSECDTNL SSPSN eNodeB
Sequence No. DSP IPSECDTNL
LST IPSECDTNL
ADD IPSECDTNL
Master Tunnel's MOD IPSECDTNL
IPSECDTNL MBFDSN eNodeB
BFD Session ID DSP IPSECDTNL
LST IPSECDTNL
ADD IPSECDTNL
Slave Tunnel's BFD MOD IPSECDTNL
IPSECDTNL SBFDSN eNodeB
Session ID DSP IPSECDTNL
LST IPSECDTNL
Current Used IPSec
IPSECDTNL CurrentUsedTunnel eNodeB DSP IPSECDTNL
Policy
IPSECPOLICY
DSP
IPSECPOLICY
IPSECPOLICY SPGN Policy Group Name eNodeB LST IPSECPOLICY
MOD
IPSECPOLICY
RMV
IPSECPOLICY
DSP
IPSECPOLICY
IPSec Sequence
IPSECPOLICY SPSN eNodeB LST IPSECPOLICY
No.
MOD
IPSECPOLICY
RMV
IPSECPOLICY
MOD
IPSECPOLICY ACLID ACL ID eNodeB IPSECPOLICY
DSP
IPSECPOLICY
IPSECPOLICY
MOD
IPSec Proposal
IPSECPOLICY PROPNAME eNodeB IPSECPOLICY
Name
DSP
IPSECPOLICY
IPSECPOLICY
MOD
IPSECPOLICY PEERNAME IKE Peer Name eNodeB IPSECPOLICY
DSP
IPSECPOLICY
ADD
IPSECPOLICY
MOD
Perfect Forward
IPSECPOLICY PFS eNodeB IPSECPOLICY
Secrecy
DSP
IPSECPOLICY
LST IPSECPOLICY
ADD
IPSECPOLICY
MOD
IPSECPOLICY LTCFG SA Duration Mode eNodeB IPSECPOLICY
DSP
IPSECPOLICY
LST IPSECPOLICY
ADD
IPSECPOLICY
MOD
Lifetime Based On
IPSECPOLICY LTS eNodeB IPSECPOLICY
Time
DSP
IPSECPOLICY
LST IPSECPOLICY
ADD
IPSECPOLICY
MOD
Lifetime Based On
IPSECPOLICY LTKB eNodeB IPSECPOLICY
Traffic
DSP
IPSECPOLICY
LST IPSECPOLICY
DSP
IPSECPOLICY CabinetNo Cabinet No. eNodeB
IPSECPOLICY
DSP
IPSECPOLICY SubrackNo Subrack No. eNodeB
IPSECPOLICY
DSP
IPSECPOLICY SlotNo Slot No. eNodeB
IPSECPOLICY
ADD
IPSECPOLICY
MOD
Anti-Replay
IPSECPOLICY REPLAYWND eNodeB IPSECPOLICY
Window Size
DSP
IPSECPOLICY
LST IPSECPOLICY
ADD
IPSECPOLICY6
DSP
IPSECPOLICY6
IPv6 Policy Group LST
IPSECPOLICY6 SPGN eNodeB
Name IPSECPOLICY6
MOD
IPSECPOLICY6
RMV
IPSECPOLICY6
ADD
IPSECPOLICY6
DSP
IPSECPOLICY6
IPv6 IPSec LST
IPSECPOLICY6 SPSN eNodeB
Sequence No. IPSECPOLICY6
MOD
IPSECPOLICY6
RMV
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
IPSECPOLICY6
IPSECPOLICY6 ACLTYPE ACL Type eNodeB
DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
IPSECPOLICY6
IPSECPOLICY6 ACLID IPv4 ACL ID eNodeB
DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
IPSECPOLICY6
IPSECPOLICY6 ACL6ID IPv6 ACL ID eNodeB
DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
IPSec Proposal IPSECPOLICY6
IPSECPOLICY6 PROPNAME eNodeB
Name DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
IPv6 IKE Peer IPSECPOLICY6
IPSECPOLICY6 PEER6NAME eNodeB
Name DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
Perfect Forward IPSECPOLICY6
IPSECPOLICY6 PFS eNodeB
Secrecy DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
IPv6 SA Duration IPSECPOLICY6
IPSECPOLICY6 LTCFG eNodeB
Mode DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
Lifetime Based On IPSECPOLICY6
IPSECPOLICY6 LTS eNodeB
Time DSP
IPSECPOLICY6
LST
IPSECPOLICY6
ADD
IPSECPOLICY6
MOD
Lifetime Based On IPSECPOLICY6
IPSECPOLICY6 LTKB eNodeB
Traffic DSP
IPSECPOLICY6
LST
IPSECPOLICY6
DSP
IPSECPOLICY6 CabinetNo Cabinet No. eNodeB
IPSECPOLICY6
DSP
IPSECPOLICY6 SubrackNo Subrack No. eNodeB
IPSECPOLICY6
DSP
IPSECPOLICY6 SlotNo Slot No. eNodeB
IPSECPOLICY6
ADD
IPSECPROPOSAL
DSP
IPSECPROPOSAL
IPSec Proposal LST
IPSECPROPOSAL PROPNAME eNodeB
Name IPSECPROPOSAL
MOD
IPSECPROPOSAL
RMV
IPSECPROPOSAL
ADD
IPSECPROPOSAL
MOD
Encapsulation IPSECPROPOSAL
IPSECPROPOSAL ENCAPMODE eNodeB
Mode DSP
IPSECPROPOSAL
LST
IPSECPROPOSAL
ADD
IPSECPROPOSAL
MOD
IPSECPROPOSAL
IPSECPROPOSAL TRANMODE Transform eNodeB
DSP
IPSECPROPOSAL
LST
IPSECPROPOSAL
ADD
IPSECPROPOSAL
MOD
AH Authentication IPSECPROPOSAL
IPSECPROPOSAL AHAUTHALG eNodeB
Algorithm DSP
IPSECPROPOSAL
LST
IPSECPROPOSAL
ADD
IPSECPROPOSAL
MOD
ESP Authentication IPSECPROPOSAL
IPSECPROPOSAL ESPAUTHALG eNodeB
Algorithm DSP
IPSECPROPOSAL
LST
IPSECPROPOSAL
ADD
IPSECPROPOSAL
MOD
ESP Encryption IPSECPROPOSAL
IPSECPROPOSAL ESPENCALG eNodeB
Algorithm DSP
IPSECPROPOSAL
LST
IPSECPROPOSAL
DSP
IPSECPROPOSAL CabinetNo Cabinet No. eNodeB
IPSECPROPOSAL
DSP
IPSECPROPOSAL SubrackNo Subrack No. eNodeB
IPSECPROPOSAL
DSP
IPSECPROPOSAL SlotNo Slot No. eNodeB
IPSECPROPOSAL
DSP
LOCALETHPORT ConfigStatus Config Status eNodeB
LOCALETHPORT
DSP
LOCALETHPORT PortStatus Port Status eNodeB
LOCALETHPORT
Number of RX DSP
LOCALETHPORT RxDropped eNodeB
Discarded Packets LOCALETHPORT
Number of RX DSP
LOCALETHPORT RxPackets eNodeB
Packets LOCALETHPORT
Number of TX DSP
LOCALETHPORT TxDropped eNodeB
Discarded Packets LOCALETHPORT
Number of TX DSP
LOCALETHPORT TxPackets eNodeB
Packets LOCALETHPORT
SET LOCALIP
LOCALIP IP IP Address eNodeB DSP LOCALIP
LST LOCALIP
SET LOCALIP
LOCALIP MASK Mask eNodeB DSP LOCALIP
LST LOCALIP
SET LOCALIP6
LOCALIP6 IP6 IPv6 Address eNodeB DSP LOCALIP6
LST LOCALIP6
SET LOCALIP6
LOCALIP6 PFXLEN Prefix Length eNodeB DSP LOCALIP6
LST LOCALIP6
LOCALIP6 AddressStatus Address Status eNodeB DSP LOCALIP6
LOCALIP6 ValidLifetime Valid Lifetime eNodeB DSP LOCALIP6
LOCALIP6 PreferredLifetime Preferred Lifetime eNodeB DSP LOCALIP6

SET LR
LR CN Cabinet No. eNodeB
LST LR
SET LR
LR SRN Subrack No. eNodeB
LST LR
SET LR
LR SN Slot No. eNodeB
LST LR
SET LR
LR PT Port Type eNodeB
LST LR
SET LR
LR PN Port No. eNodeB
LST LR
SET LR
LR LRSW LR Switch eNodeB
LST LR
UL Committed SET LR
LR CIR eNodeB
Information Rate LST LR
Committed Burst SET LR
LR CBS eNodeB
Size LST LR
SET LR
LR EBS Excess Burst Size eNodeB
LST LR
SET LR
LR SBT Subboard Type eNodeB
LST LR
DL Committed SET LR
LR DLCIR eNodeB
Information Rate LST LR
ADD MPGRP
DSP MPGRP
MPGRP CN Cabinet No. eNodeB RMV MPGRP
RST MPGRP
LST MPGRP
ADD MPGRP
DSP MPGRP
MPGRP SRN Subrack No. eNodeB RMV MPGRP
RST MPGRP
LST MPGRP
ADD MPGRP
DSP MPGRP
MPGRP SN Slot No. eNodeB RMV MPGRP
RST MPGRP
LST MPGRP
ADD MPGRP
DSP MPGRP
RMV MPGRP
MPGRP MPGRPN MLPPP Group No. eNodeB
RST MPGRP
DSP DHCPRSLT
LST MPGRP
ADD MPGRP
MPGRP MCPPP Multi-Class PPP eNodeB DSP MPGRP
LST MPGRP
ADD MPGRP
MPGRP AUTH Authentication Type eNodeB
LST MPGRP
ADD MPGRP
MPGRP UN User Name eNodeB
LST MPGRP
ADD MPGRP
MPGRP PWD Password eNodeB
LST MPGRP
ADD MPGRP
MPGRP LOCALIP Local IP eNodeB DSP MPGRP
LST MPGRP
ADD MPGRP
MPGRP IPMASK Mask eNodeB DSP MPGRP
LST MPGRP
ADD MPGRP
MPGRP PEERIP Peer IP eNodeB DSP MPGRP
LST MPGRP
MP/MC Header ADD MPGRP

MPGRP MHO eNodeB
Option LST MPGRP
ADD MPGRP
MPGRP MUXCP PPPMUX eNodeB DSP MPGRP
LST MPGRP
MLPPP Fragment ADD MPGRP
MPGRP FRAGSIZE eNodeB
Size LST MPGRP
PPP Mux Subframe ADD MPGRP

MPGRP MAXSFLEN eNodeB
Max Length LST MPGRP
PPP Muxframe Max ADD MPGRP

MPGRP MAXMFLEN eNodeB
Length LST MPGRP
PPPMUX Combine ADD MPGRP
MPGRP MUXTIME eNodeB
Timeout LST MPGRP
ADD MPGRP
MPGRP MCCLASS MCPPP Class eNodeB
LST MPGRP
ADD MPGRP
IP Header
MPGRP IPHC eNodeB DSP MPGRP
Compression
LST MPGRP
MLPPP Packets
ADD MPGRP
MPGRP MPDAAT Discard Alarm eNodeB
LST MPGRP
Appear Threshold
MLPPP Packets
Discard Alarm ADD MPGRP
MPGRP MPDADT eNodeB
Disappear LST MPGRP
Threshold
MLPPP Group
MPGRP MPGroupStatus eNodeB DSP MPGRP
Status
MPGRP IPCPSTATUS IPCP Status eNodeB DSP MPGRP
MPGRP PPPMUXSTATUS PPPMUX Status eNodeB DSP MPGRP
Local IP Negotiation
MPGRP LOCALIPNEGRLT eNodeB DSP MPGRP
Result
Local IP Mask
MPGRP IPMASKNEGRLT eNodeB DSP MPGRP
Negotiation Result
Peer IP Negotiation
MPGRP PEERIPNEGRLT eNodeB DSP MPGRP
Result
Multi-Class PPP
MPGRP MCPPPNEGRLT eNodeB DSP MPGRP
Negotiation Result
Maximum Receive
MPGRP MRUNEGRLT Unit Negotiation eNodeB DSP MPGRP
Result
PPPMUX
MPGRP MUXNEGRLT eNodeB DSP MPGRP
Negotiation Result
ACFC Negotiation
MPGRP ACFCNEGRLT eNodeB DSP MPGRP
Result
PFC Negotiation
MPGRP PFCNEGRLT eNodeB DSP MPGRP
Result
IPHC Negotiation
MPGRP IPHCNEGRLT eNodeB DSP MPGRP
Result
Number of RX
MPGRP RXPKT eNodeB DSP MPGRP
Packets
Number of TX
MPGRP TXPKT eNodeB DSP MPGRP
Packets
MPGRP RXFLOW RX Flow eNodeB DSP MPGRP
MPGRP TXFLOW TX Flow eNodeB DSP MPGRP
MPGRP IPNum Number of IPs eNodeB DSP MPGRP
MPGRP IPList IP Address List eNodeB DSP MPGRP
ADD MPGRP
DSP MPGRP
MPGRP SBT Subboard Type eNodeB RMV MPGRP
RST MPGRP
LST MPGRP
Number of RX
MPGRP RXBYTE eNodeB DSP MPGRP
Bytes
Number of RX Drop
MPGRP RXDROPPKT eNodeB DSP MPGRP
Packets
Number of TX
MPGRP TXBYTE eNodeB DSP MPGRP
Bytes
Number of TX Drop
MPGRP TXDROPPKT eNodeB DSP MPGRP
Packets
ADD MPLNK
DSP MPLNK
MPLNK CN Cabinet No. eNodeB
RMV MPLNK
LST MPLNK
ADD MPLNK
DSP MPLNK
MPLNK SRN Subrack No. eNodeB
RMV MPLNK
LST MPLNK
ADD MPLNK
DSP MPLNK
MPLNK SN Slot No. eNodeB
RMV MPLNK
LST MPLNK
ADD MPLNK
DSP MPLNK
MPLNK PPPLNKN MLPPP Link No. eNodeB RMV MPLNK
DSP DHCPRSLT
LST MPLNK
ADD MPLNK
MPLNK MPGRPN MLPPP Group No. eNodeB DSP MPLNK
LST MPLNK
ADD MPLNK
MPLNK E1T1SRN E1/T1 Subrack No. eNodeB
LST MPLNK
ADD MPLNK
MPLNK E1T1SN E1/T1 Slot No. eNodeB
LST MPLNK
ADD MPLNK
MPLNK E1T1PN E1/T1 Port No. eNodeB
LST MPLNK
ADD MPLNK
MPLNK TSN Timeslot No. eNodeB
LST MPLNK
ADD MPLNK
Maximum Receive
MPLNK MRU eNodeB DSP MPLNK
Unit
LST MPLNK
ADD MPLNK
Protocol Field
MPLNK PFC eNodeB DSP MPLNK
Compression
LST MPLNK
Address and ADD MPLNK
MPLNK ACFC Control Field eNodeB DSP MPLNK
Compression LST MPLNK
ADD MPLNK
MPLNK RESTARTTMR Negotiation Time eNodeB
LST MPLNK
ADD MPLNK
DSP MPLNK
MPLNK SBT Subboard Type eNodeB
RMV MPLNK
LST MPLNK
MLPPP Group ADD MPLNK

MPLNK MPGRPSBT eNodeB
Subboard Type LST MPLNK
MPLNK MPLNKSTATUS MLPPP Link Status eNodeB DSP MPLNK

MPLNK LCPSTATUS LCP Status eNodeB DSP MPLNK
Maximum Receive
MPLNK MRUNEGRLT Unit Negotiation eNodeB DSP MPLNK
Result
PFC Negotiation
MPLNK PFCNEGRLT eNodeB DSP MPLNK
Result
ACFC Negotiation
MPLNK ACFCNEGRLT eNodeB DSP MPLNK
Result
E1/T1 Subboard ADD MPLNK

MPLNK E1T1SBT eNodeB
Type LST MPLNK
Number of RX
MPLNK RXPKT eNodeB DSP MPLNK
Packets
Number of RX
MPLNK RXBYTE eNodeB DSP MPLNK
Bytes
Number of RX Drop
MPLNK RXDROPPKT eNodeB DSP MPLNK
Packets
Number of TX
MPLNK TXPKT eNodeB DSP MPLNK
Packets
Number of TX
MPLNK TXBYTE eNodeB DSP MPLNK
Bytes
Number of TX Drop
MPLNK TXDROPPKT eNodeB DSP MPLNK
Packets
ADD OMCH
DSP OMCH
OMCH FLAG Master/Slave Flag eNodeB MOD OMCH
RMV OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH IP Local IP eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH MASK Local Mask eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH PEERIP Peer IP eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH PEERMASK Peer Mask eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH CN Cabinet No. eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH SRN Subrack No. eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH SN Slot No. eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
OMCH BEAR Bearer Type eNodeB MOD OMCH
DSP DHCPRSLT
ADD OMCH
MOD OMCH
OMCH BRT Binding Route eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH DSTIP Destination IP eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH DSTMASK Destination Mask eNodeB DSP DHCPRSLT
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH RT Route Type eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH IFT Interface Type eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH IFNO Interface No. eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH PREF Preference eNodeB
DSP OMCH
LST OMCH
ADD OMCH
MOD OMCH
OMCH NEXTHOP Next Hop IP eNodeB
DSP OMCH
LST OMCH
OMCH Status OM Channel Status eNodeB DSP OMCH
OMCH UsedState Used State eNodeB DSP OMCH
ADD OMCH
MOD OMCH
OMCH SBT Subboard Type eNodeB
DSP OMCH
LST OMCH
ADD OMCH6
MOD OMCH6
OMCH6 LOCALIP6 Local IPv6 Address eNodeB
DSP OMCH6
LST OMCH6
ADD OMCH6
MOD OMCH6
OMCH6 PEERIP6 Peer IPv6 Address eNodeB
DSP OMCH6
LST OMCH6
OMCH6 Status OM Channel Status eNodeB DSP OMCH6
ADD
PACKETFILTER
DSP
PACKETFILTER
PACKETFILTER CN Cabinet No. eNodeB
RMV
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER
PACKETFILTER SRN Subrack No. eNodeB
RMV
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER
PACKETFILTER SN Slot No. eNodeB
RMV
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER
PACKETFILTER PT Port Type eNodeB
RMV
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER
PACKETFILTER PN Port No. eNodeB
RMV
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER ACLID Advanced ACL ID eNodeB
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER MB Match Behavior eNodeB
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER
PACKETFILTER SBT Subboard Type eNodeB
RMV
PACKETFILTER
LST
PACKETFILTER
Number of TX DSP
PACKETFILTER TxPackets eNodeB
Packets PACKETFILTER
Number of RX DSP
PACKETFILTER RxPackets eNodeB
Number of TX DSP
PACKETFILTER TxPermitPacket eNodeB
Permit Packets PACKETFILTER
Number of RX DSP
PACKETFILTER RxPermitPacket eNodeB
Permit Packets PACKETFILTER
Number of TX Deny DSP

PACKETFILTER TxDenyPacket eNodeB
Number of RX Deny DSP

PACKETFILTER RxDenyPacket eNodeB
Bytes of TX DSP
PACKETFILTER TxBytes eNodeB
Bytes of RX DSP
PACKETFILTER RxBytes eNodeB
Bytes of TX Permit DSP

PACKETFILTER TxPermitBytes eNodeB
Bytes of RX Permit DSP

PACKETFILTER RxPermitBytes eNodeB
Bytes of TX Deny DSP

PACKETFILTER TxDenyBytes eNodeB
Bytes of RX Deny DSP

PACKETFILTER RxDenyBytes eNodeB
Bytes of RX
DSP
PACKETFILTER RxDefaultBytes Packets Matched eNodeB
PACKETFILTER
Default Behavior
Number of RX
DSP
PACKETFILTER RxDefaultPackets Packets Matched eNodeB
PACKETFILTER
Default Behavior
ADD
PACKETFILTER
DSP
PACKETFILTER ACLID2 Layer 2 ACL ID eNodeB
PACKETFILTER
LST
PACKETFILTER
ADD
PACKETFILTER
DSP
PACKETFILTER FM Filter Mode eNodeB
PACKETFILTER
LST
PACKETFILTER
ADD PINGFILTER
PINGFILTER IP IP Address eNodeB RMV PINGFILTER
LST PINGFILTER
ADD PINGFILTER
PINGFILTER MASK Mask eNodeB RMV PINGFILTER
LST PINGFILTER
SET PMTUCFG
PMTUCFG MODE Detection Mode eNodeB
LST PMTUCFG
SET PMTUCFG
PMTUCFG UDPPORT UDP Port No. eNodeB
LST PMTUCFG
SET PMTUCFG
PMTUCFG DETECTPERIOD Detection Period eNodeB
LST PMTUCFG
SET PMTUCFG
PMTUCFG AGINGPERIOD Aging Period eNodeB
LST PMTUCFG
SET PMTUCFG
PMTUCFG DSCP DSCP eNodeB
LST PMTUCFG
DSP
PORTSECURITY
SET
PORTSECURITY CN Cabinet No. eNodeB
PORTSECURITY
LST
PORTSECURITY
DSP
PORTSECURITY
SET
PORTSECURITY SRN Subrack No. eNodeB
PORTSECURITY
LST
PORTSECURITY
DSP
PORTSECURITY
SET
PORTSECURITY SN Slot No. eNodeB
PORTSECURITY
LST
PORTSECURITY
DSP
PORTSECURITY
SET
PORTSECURITY SBT Subboard Type eNodeB
PORTSECURITY
LST
PORTSECURITY
DSP
PORTSECURITY
SET
PORTSECURITY PT Port Type eNodeB
PORTSECURITY
LST
PORTSECURITY
DSP
PORTSECURITY
SET
PORTSECURITY PN Port No. eNodeB
PORTSECURITY
LST
PORTSECURITY
SET
PORTSECURITY
DSP
PORTSECURITY SWITCH Enable Flag eNodeB
PORTSECURITY
LST
PORTSECURITY
ADD PPPLNK
DSP PPPLNK
PPPLNK CN Cabinet No. eNodeB RMV PPPLNK
RST PPPLNK
LST PPPLNK
ADD PPPLNK
DSP PPPLNK
PPPLNK SRN Subrack No. eNodeB RMV PPPLNK
RST PPPLNK
LST PPPLNK
ADD PPPLNK
DSP PPPLNK
PPPLNK SN Slot No. eNodeB RMV PPPLNK
RST PPPLNK
LST PPPLNK
ADD PPPLNK
DSP PPPLNK
RMV PPPLNK
PPPLNK PPPLNKN PPP Link No. eNodeB
RST PPPLNK
DSP DHCPRSLT
LST PPPLNK
ADD PPPLNK
PPPLNK PN Port No. eNodeB
LST PPPLNK
ADD PPPLNK
PPPLNK AUTH Authentication Type eNodeB
LST PPPLNK
ADD PPPLNK
PPPLNK UN User Name eNodeB
LST PPPLNK
ADD PPPLNK
PPPLNK PWD Password eNodeB
LST PPPLNK
ADD PPPLNK
PPPLNK TSN Time Slot No. eNodeB
LST PPPLNK
ADD PPPLNK
PPPLNK LOCALIP Local IP eNodeB DSP PPPLNK
LST PPPLNK
ADD PPPLNK
PPPLNK IPMASK Mask eNodeB DSP PPPLNK
LST PPPLNK
ADD PPPLNK
PPPLNK PEERIP Peer IP eNodeB DSP PPPLNK
LST PPPLNK
ADD PPPLNK
PPPLNK MUXCP PPPMUX eNodeB DSP PPPLNK
LST PPPLNK
Maximum Length of ADD PPPLNK

PPPLNK MAXSFLEN eNodeB
PPP Mux Subframe LST PPPLNK
Maximum Length of ADD PPPLNK

PPPLNK MAXMFLEN eNodeB
PPP Muxframe LST PPPLNK
PPP Muxframe
ADD PPPLNK
PPPLNK MUXTIME Combination eNodeB
LST PPPLNK
Timeout
ADD PPPLNK
IP Header
PPPLNK IPHC eNodeB DSP PPPLNK
Compression
LST PPPLNK
ADD PPPLNK
Maximum Receive
PPPLNK MRU eNodeB DSP PPPLNK
Unit
LST PPPLNK
ADD PPPLNK
Protocol Field
PPPLNK PFC eNodeB DSP PPPLNK
Compression
LST PPPLNK
Address and ADD PPPLNK

PPPLNK ACFC Control Field eNodeB DSP PPPLNK
Compression LST PPPLNK
ADD PPPLNK
PPPLNK RESTARTTMR Negotiation Time eNodeB
LST PPPLNK
PPPLNK PPPLinkStatus Link Status eNodeB DSP PPPLNK
PPPLNK LCPSTATUS LCP Status eNodeB DSP PPPLNK
PPPLNK IPCPSTATUS IPCP Status eNodeB DSP PPPLNK

PPPLNK PPPMUXSTATUS PPPMUX Status eNodeB DSP PPPLNK
Local IP Negotiation
PPPLNK LOCALIPNEGRLT eNodeB DSP PPPLNK
Result
Local IP Mask
PPPLNK MASKNEGRLT eNodeB DSP PPPLNK
Negotiation Result
Peer IP Negotiation
PPPLNK PEERIPNEGRLT eNodeB DSP PPPLNK
Result
IPHC Negotiation
PPPLNK IPHCNEGRLT eNodeB DSP PPPLNK
Result
ACFC Negotiation
PPPLNK ACFCNEGRLT eNodeB DSP PPPLNK
Result
PFC Negotiation
PPPLNK PFCNEGRLT eNodeB DSP PPPLNK
Result
Maximum Receive
PPPLNK MRUNEGRLT Unit Negotiation eNodeB DSP PPPLNK
Result
PPPMUX
PPPLNK MUXNEGRLT eNodeB DSP PPPLNK
Negotiation Result
Number of RX
PPPLNK RXPKT eNodeB DSP PPPLNK
Packets
Number of TX
PPPLNK TXPKT eNodeB DSP PPPLNK
Packets
PPPLNK RXFLOW RX Flow eNodeB DSP PPPLNK
PPPLNK TXFLOW TX Flow eNodeB DSP PPPLNK
PPPLNK IPNum Number of IPs eNodeB DSP PPPLNK
PPPLNK IPList IP Address List eNodeB DSP PPPLNK
PPP Fault Frame

ADD PPPLNK
PPPLNK FFAPHOLD Occurrence eNodeB
LST PPPLNK
Threshold
PPP Fault Frame ADD PPPLNK

PPPLNK FFDPHOLD eNodeB
Clear Threshold LST PPPLNK
ADD PPPLNK
DSP PPPLNK
PPPLNK SBT Subboard Type eNodeB RMV PPPLNK
RST PPPLNK
LST PPPLNK
Number of RX
PPPLNK RXBYTE eNodeB DSP PPPLNK
Bytes
Number of RX Drop
PPPLNK RXDROPPKT eNodeB DSP PPPLNK
Packets
Number of TX
PPPLNK TXBYTE eNodeB DSP PPPLNK
Bytes
Number of TX Drop
PPPLNK TXDROPPKT eNodeB DSP PPPLNK
Packets
SET PRI2QUE
PRI2QUE PRI0 PriOfQue0 eNodeB
LST PRI2QUE
SET PRI2QUE
LST PRI2QUE
SET PRI2QUE
LST PRI2QUE
SET PRI2QUE
LST PRI2QUE
SET PRI2QUE
LST PRI2QUE
SET PRI2QUE
LST PRI2QUE
SET PRI2QUE
LST PRI2QUE
ADD RSCGRP
DSP RSCGRP
RSCGRP CN Cabinet No. eNodeB MOD RSCGRP
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
DSP RSCGRP
RSCGRP SRN Subrack No. eNodeB MOD RSCGRP
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
DSP RSCGRP
RSCGRP SN Slot No. eNodeB MOD RSCGRP
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
Transmission DSP RSCGRP
RSCGRP BEAR Resource Group eNodeB MOD RSCGRP
Bear Type RMV RSCGRP
LST RSCGRP
ADD RSCGRP
DSP RSCGRP
RSCGRP SBT Subboard Type eNodeB MOD RSCGRP
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
DSP RSCGRP
RSCGRP PT Bearing Port Type eNodeB MOD RSCGRP
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
DSP RSCGRP
RSCGRP PN Bearing Port No. eNodeB MOD RSCGRP
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
DSP RSCGRP
Transmission
RSCGRP RSCGRPID eNodeB MOD RSCGRP
Resource Group ID
RMV RSCGRP
LST RSCGRP
ADD RSCGRP
MOD RSCGRP
RSCGRP RU Rate Unit eNodeB
DSP RSCGRP
LST RSCGRP
ADD RSCGRP
MOD RSCGRP
RSCGRP TXBW Tx Bandwidth eNodeB
DSP RSCGRP
LST RSCGRP
ADD RSCGRP
MOD RSCGRP
RSCGRP RXBW Rx Bandwidth eNodeB
DSP RSCGRP
LST RSCGRP
ADD RSCGRP
TX Committed
RSCGRP TXCBS eNodeB MOD RSCGRP
Burst Size
LST RSCGRP
ADD RSCGRP
TX Excessive Burst
RSCGRP TXEBS eNodeB MOD RSCGRP
Size
LST RSCGRP
ADD RSCGRP
RSCGRP OID Operator ID eNodeB
LST RSCGRP
ADD RSCGRP
RSCGRP WEIGHT Scheduling Weight eNodeB MOD RSCGRP
LST RSCGRP
ADD RSCGRP
TX Committed
RSCGRP TXCIR eNodeB MOD RSCGRP
Information Rate
LST RSCGRP
ADD RSCGRP
RX Committed
RSCGRP RXCIR eNodeB MOD RSCGRP
Information Rate
LST RSCGRP
ADD RSCGRP
TX Peak
RSCGRP TXPIR eNodeB MOD RSCGRP
Information Rate
LST RSCGRP
ADD RSCGRP
RX Peak
RSCGRP RXPIR eNodeB MOD RSCGRP
Information Rate
LST RSCGRP
ADD RSCGRP
RSCGRP TXPBS TX Peak Burst Size eNodeB MOD RSCGRP
LST RSCGRP
Realtime TX
RSCGRP TxRTBw eNodeB DSP RSCGRP
Bandwidth
Realtime RX
RSCGRP RxRTBw eNodeB DSP RSCGRP
Bandwidth
Non-Realtime TX
RSCGRP TxNRTBw eNodeB DSP RSCGRP
Bandwidth
Non-Realtime RX
RSCGRP RxNRTBw eNodeB DSP RSCGRP
Bandwidth
Non-Realtime
RSCGRP TxNRTResvBw Reserved TX eNodeB DSP RSCGRP
Bandwidth
Non-Realtime
RSCGRP RxNRTResvBw Reserved RX eNodeB DSP RSCGRP
Bandwidth
RSCGRP TxGBRBwRlt GBR Tx Bandwidth eNodeB DSP RSCGRP
RSCGRP RxGBRBwRlt GBR Rx Bandwidth eNodeB DSP RSCGRP
Rate Configuration
RSCGRP RateCfgType eNodeB DSP RSCGRP
Type
UL Admission
RSCGRP ULAdminBw eNodeB DSP RSCGRP
Bandwidth
DL Admission
RSCGRP DLAdminBw eNodeB DSP RSCGRP
Bandwidth
UL CIR Admission
RSCGRP ULCirAdminBw eNodeB DSP RSCGRP
Bandwidth
DL CIR Admission
RSCGRP DLCirAdminBw eNodeB DSP RSCGRP
Bandwidth
UL PIR Admission
RSCGRP ULPirAdminBw eNodeB DSP RSCGRP
Bandwidth
DL PIR Admission
RSCGRP DLPirAdminBw eNodeB DSP RSCGRP
Bandwidth
RSCGRP TxLgcPortFlow Realtime Tx Traffic eNodeB DSP RSCGRP
SET RSCGRPALG
RSCGRPALG CN Cabinet No. eNodeB
LST RSCGRPALG
SET RSCGRPALG
RSCGRPALG SRN Subrack No. eNodeB
LST RSCGRPALG
SET RSCGRPALG
RSCGRPALG SN Slot No. eNodeB
LST RSCGRPALG
SET RSCGRPALG
RSCGRPALG SBT Subboard Type eNodeB
LST RSCGRPALG
SET RSCGRPALG
RSCGRPALG PT Bearing Port Type eNodeB
LST RSCGRPALG
SET RSCGRPALG
RSCGRPALG PN Bearing Port No. eNodeB
LST RSCGRPALG
Transmission SET RSCGRPALG
RSCGRPALG RSCGRPID eNodeB
Resource Group ID LST RSCGRPALG
TX Traffic Shaping SET RSCGRPALG

RSCGRPALG TXSSW eNodeB
Switch LST RSCGRPALG
TX Bandwidth SET RSCGRPALG
RSCGRPALG TXBWASW eNodeB
Adjustment Switch LST RSCGRPALG
RX Bandwidth SET RSCGRPALG
RSCGRPALG RXBWASW eNodeB
Adjustment Switch LST RSCGRPALG
Packet Loss Ratio SET RSCGRPALG

RSCGRPALG PLRDTH eNodeB
Down Threshold LST RSCGRPALG
Delay Variation SET RSCGRPALG
RSCGRPALG DDTH eNodeB
Down Threshold LST RSCGRPALG
TX Bandwidth SET RSCGRPALG

RSCGRPALG TXBWAMIN eNodeB
Adjust Minimum LST RSCGRPALG
RX Bandwidth SET RSCGRPALG
RSCGRPALG RXBWAMIN eNodeB
Adjust Minimum LST RSCGRPALG
Traffic Control SET RSCGRPALG

RSCGRPALG TCSW eNodeB
Switch LST RSCGRPALG
OM FTP Traffic SET RSCGRPALG
RSCGRPALG OMTCSW eNodeB
Control Switch LST RSCGRPALG
SET RSCGRPALG
RSCGRPALG PQN PQ Number eNodeB
LST RSCGRPALG
Congestion Time SET RSCGRPALG

RSCGRPALG CTTH eNodeB
Threshold LST RSCGRPALG
Congestion Clear SET RSCGRPALG
RSCGRPALG CCTTH eNodeB
Time Threshold LST RSCGRPALG
TX Reserved SET RSCGRPALG

RSCGRPALG TXRSVBW eNodeB
Bandwidth LST RSCGRPALG
RX Reserved SET RSCGRPALG
RSCGRPALG RXRSVBW eNodeB
Bandwidth LST RSCGRPALG
Drop Packet SET RSCGRPALG

RSCGRPALG DROPPKTNUM eNodeB
Number Threshold LST RSCGRPALG
ADD SCTPLNK
BLK SCTPLNK
DSP SCTPLNK
LST SCTPLNK
SCTPLNK SCTPNO SCTP Link No. eNodeB
MOD SCTPLNK
RMV SCTPLNK
RST SCTPLNK
UBL SCTPLNK
ADD SCTPLNK
SCTPLNK CN Cabinet No. eNodeB DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK SRN Subrack No. eNodeB DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK SN Slot No. eNodeB DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
Maximum Stream
SCTPLNK MAXSTREAM eNodeB MOD SCTPLNK
No.
LST SCTPLNK
ADD SCTPLNK
First Local IP MOD SCTPLNK
SCTPLNK LOCIP eNodeB
Address DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
Second Local IP MOD SCTPLNK
SCTPLNK SECLOCIP eNodeB
Address DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
Local SCTP Port MOD SCTPLNK
SCTPLNK LOCPORT eNodeB
No. DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
First Peer IP MOD SCTPLNK
SCTPLNK PEERIP eNodeB
Address DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
Second Peer IP MOD SCTPLNK
SCTPLNK SECPEERIP eNodeB
Address DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
Peer SCTP Port MOD SCTPLNK
SCTPLNK PEERPORT eNodeB
No. DSP SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK RTOMIN RTO Min Value eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK RTOMAX RTO Max Value eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK RTOINIT RTO Initial Value eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK RTOALPHA RTO Alpha Value eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK RTOBETA RTO Beta Value eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK HBINTER Heart-beat Interval eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
Max Association
SCTPLNK MAXASSOCRETR eNodeB MOD SCTPLNK
Retransmission
LST SCTPLNK
ADD SCTPLNK
Max Path
SCTPLNK MAXPATHRETR eNodeB MOD SCTPLNK
Retransmission
LST SCTPLNK
ADD SCTPLNK
Send Message
SCTPLNK CHKSUMTX eNodeB MOD SCTPLNK
Checksum Flag
LST SCTPLNK
ADD SCTPLNK
Receive Message
SCTPLNK CHKSUMRX eNodeB MOD SCTPLNK
Checksum Flag
LST SCTPLNK
ADD SCTPLNK
Checksum
SCTPLNK CHKSUMTYPE eNodeB MOD SCTPLNK
Arithmetic Type
LST SCTPLNK
ADD SCTPLNK
SCTPLNK AUTOSWITCH Switch Back Flag eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK eNodeB MOD SCTPLNK
UM When Switch Back
LST SCTPLNK
SCTPLNK AssocState SCTP Link Status eNodeB DSP SCTPLNK

Status Change
SCTPLNK TransferCause eNodeB DSP SCTPLNK
Cause
Status Change
SCTPLNK TransferTime eNodeB DSP SCTPLNK
Time
SCTPLNK OUTSTREAM Out Stream Number eNodeB DSP SCTPLNK
SCTPLNK INSTREAM In Stream Number eNodeB DSP SCTPLNK
SCTPLNK WORKADDRFLAG Work Address Flag eNodeB DSP SCTPLNK
DSP SCTPLNK
SCTPLNK BLKFLAG Block Flag eNodeB
LST SCTPLNK
ADD SCTPLNK
SCTPLNK TSACK SACK Timeout eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK
SCTPLNK DESCRI Description Info eNodeB MOD SCTPLNK
LST SCTPLNK
ADD SCTPLNK6
BLK SCTPLNK6
DSP SCTPLNK6
LST SCTPLNK6
SCTPLNK6 SCTPNO IPv6 SCTP Link No. eNodeB
MOD SCTPLNK6
RMV SCTPLNK6
RST SCTPLNK6
UBL SCTPLNK6
ADD SCTPLNK6
Maximum Stream
SCTPLNK6 MAXSTREAM eNodeB MOD SCTPLNK6
No.
LST SCTPLNK6
ADD SCTPLNK6
First Local IPv6 MOD SCTPLNK6
SCTPLNK6 LOCIP eNodeB
Address DSP SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
Second Local IPv6 MOD SCTPLNK6
SCTPLNK6 SECLOCIP eNodeB
LST SCTPLNK6
ADD SCTPLNK6
Local IPv6 SCTP MOD SCTPLNK6
SCTPLNK6 LOCPORT eNodeB
Port No. DSP SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
First Peer IPv6 MOD SCTPLNK6
SCTPLNK6 PEERIP eNodeB
LST SCTPLNK6
ADD SCTPLNK6
Second Peer IPv6 MOD SCTPLNK6
SCTPLNK6 SECPEERIP eNodeB
LST SCTPLNK6
ADD SCTPLNK6
Peer IPv6 SCTP MOD SCTPLNK6
SCTPLNK6 PEERPORT eNodeB
Port No. DSP SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 RTOMIN RTO Min Value eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 RTOMAX RTO Max Value eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 RTOINIT RTO Initial Value eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 RTOALPHA RTO Alpha Value eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 RTOBETA RTO Beta Value eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 HBINTER Heart-beat Interval eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD SCTPLNK6
Max Association
SCTPLNK6 MAXASSOCRETR eNodeB MOD SCTPLNK6
Retransmission
LST SCTPLNK6
ADD SCTPLNK6
Max Path
SCTPLNK6 MAXPATHRETR eNodeB MOD SCTPLNK6
Retransmission
LST SCTPLNK6
ADD SCTPLNK6
Checksum
SCTPLNK6 CHKSUMTYPE eNodeB MOD SCTPLNK6
Algorithm Type
LST SCTPLNK6
ADD SCTPLNK6
SWITCHBACKFLA
SCTPLNK6 Switch Back Flag eNodeB MOD SCTPLNK6
G
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 eNodeB MOD SCTPLNK6
UM When Switch Back
LST SCTPLNK6
IPv6 SCTP Link

SCTPLNK6 AssocState eNodeB DSP SCTPLNK6
Status
Status Change
SCTPLNK6 TransferCause eNodeB DSP SCTPLNK6
Cause
Status Change
SCTPLNK6 TransferTime eNodeB DSP SCTPLNK6
Time
SCTPLNK6 OUTSTREAM Out Stream Number eNodeB DSP SCTPLNK6
SCTPLNK6 INSTREAM In Stream Number eNodeB DSP SCTPLNK6
SCTPLNK6 WORKADDRFLAG Work Address Flag eNodeB DSP SCTPLNK6
DSP SCTPLNK6
SCTPLNK6 BLKFLAG Block Flag eNodeB
LST SCTPLNK6
ADD SCTPLNK6
SCTPLNK6 DESCRI Description Info eNodeB MOD SCTPLNK6
LST SCTPLNK6
ADD
SUBNETVLAN
LST SUBNETVLAN
SUBNETVLAN IP IP Address eNodeB MOD
SUBNETVLAN
RMV
SUBNETVLAN
ADD
SUBNETVLAN
LST SUBNETVLAN
SUBNETVLAN MASK Mask eNodeB MOD
SUBNETVLAN
RMV
SUBNETVLAN
ADD
SUBNETVLAN
SUBNETVLAN VLANID VLAN ID eNodeB MOD
SUBNETVLAN
LST SUBNETVLAN
Resource Group
RSCGRPULCACS Uplink Admission SET TACALG
TACALG eNodeB
WITCH Control Algorithm LST TACALG
Switch
Resource Group
RSCGRPDLCACS Downlink Admission SET TACALG
TACALG eNodeB
WITCH Control Algorithm LST TACALG
Switch
USERDATATYPE1 User Data Type 1 SET TACALG
TACALG eNodeB
ACTFACTOR Act Factor LST TACALG

TACALG eNodeB

TACALG eNodeB
TACALG eNodeB

TACALG eNodeB

TACALG eNodeB
TACALG eNodeB

TACALG eNodeB

TACALG eNodeB
Uplink Handover
SET TACALG
TACALG TRMULHOCACTH Service Admission eNodeB
LST TACALG
Threshold
Downlink Handover
SET TACALG
TACALG TRMDLHOCACTH Service Admission eNodeB
LST TACALG
Threshold
Uplink Golden New
TRMULGOLDCAC SET TACALG
TACALG Service Admission eNodeB
TH LST TACALG
Threshold
Downlink Golden
TRMDLGOLDCAC New Service SET TACALG
TACALG eNodeB
TH Admission LST TACALG
Threshold
Uplink Silver New
TRMULSILVERCA SET TACALG
CTH LST TACALG
Threshold
Downlink Silver
TRMDLSILVERCA New Service SET TACALG
TACALG eNodeB
CTH Admission LST TACALG
Threshold
Uplink Bronze New
TRMULBRONZEC SET TACALG
ACTH LST TACALG
Threshold
Downlink Bronze
TRMDLBRONZEC New Service SET TACALG
TACALG eNodeB
ACTH Admission LST TACALG
Threshold
Uplink GBR Service
TRMULGBRCACT SET TACALG
TACALG Admission eNodeB
H LST TACALG
Threshold
Downlink GBR
TRMDLGBRCACT SET TACALG
H LST TACALG
Threshold
Uplink Pre-emption SET TACALG
TACALG TRMULPRESW eNodeB
Algorithm Switch LST TACALG
Downlink Pre-
SET TACALG
TACALG TRMDLPRESW emption Algorithm eNodeB
LST TACALG
Switch
Physical Port Up
SET TACALG
TACALG PORTULOBSW Link OverBooking eNodeB
LST TACALG
Switch
Physical Port Down
SET TACALG
TACALG PORTDLOBSW Link OverBooking eNodeB
LST TACALG
Switch
Physical Port Up
SET TACALG
TACALG PORTULCACSW Link Admission eNodeB
LST TACALG
Switch
Physical Port Down
SET TACALG
TACALG PORTDLCACSW Link Admission eNodeB
LST TACALG
Switch
Uplink High Load SET TLDRALG

TLDRALG TRMULLDRTRGTH eNodeB
Trigger Threshold LST TLDRALG
Downlink High Load SET TLDRALG
TLDRALG TRMDLLDRTRGTH eNodeB
Trigger Threshold LST TLDRALG
Uplink High Load SET TLDRALG

TLDRALG TRMULLDRCLRTH eNodeB
Clear Threshold LST TLDRALG
Downlink High Load SET TLDRALG
TLDRALG TRMDLLDRCLRTH eNodeB
Clear Threshold LST TLDRALG
Uplink Medium
TRMULMLDTRGT SET TLDRALG
TLDRALG Load Trigger eNodeB
H LST TLDRALG
Threshold
Downlink Medium
TRMDLMLDTRGT SET TLDRALG
TLDRALG Load Trigger eNodeB
H LST TLDRALG
Threshold
Uplink Medium
SET TLDRALG
TLDRALG TRMULMLDCLRTH Load Clear eNodeB
LST TLDRALG
Threshold
Downlink Medium
SET TLDRALG
TLDRALG TRMDLMLDCLRTH Load Clear eNodeB
LST TLDRALG
Threshold
Transmission Link
SET TLFRSWITCH
TLFRSWITCH TLFRSWITCH Fault Recover eNodeB
LST TLFRSWITCH
Switch
TRMULOLCSWITC Uplink OLC SET TOLCALG
TOLCALG eNodeB
H Algorithm Switch LST TOLCALG
TRMDLOLCSWITC Downlink OLC SET TOLCALG

TOLCALG eNodeB
H Algorithm Switch LST TOLCALG
TRMULOLCTRIGT Uplink OLC Trigger SET TOLCALG
TOLCALG eNodeB
H Threshold LST TOLCALG
Uplink OLC SET TOLCALG

TOLCALG TRMULOLCRELTH eNodeB
Release Threshold LST TOLCALG
TRMOLCRELBEAR OLC Release SET TOLCALG

TOLCALG eNodeB
ERNUM Bearer No. LST TOLCALG
TRMDLOLCTRIGT Downlink OLC SET TOLCALG
TOLCALG eNodeB
H Trigger Threshold LST TOLCALG
Downlink OLC SET TOLCALG

TOLCALG TRMDLOLCRELTH eNodeB
Release Threshold LST TOLCALG
SET
PINGFILTERMODE
TRANSPORT MODE Ping Filter Mode eNodeB
LST
PINGFILTERMODE
Number of Packets
Discarded Due to
TRANSPORT BatchFailPkt eNodeB DSP IPSTAT
Fragmentation
Failures
Total Number of
Encrypted Packets
TRANSPORT InEncryptedPkt Received at the IP eNodeB DSP IPSTAT
Layer of the
Receiver
Number of Packets
Successfully
InDecryptSucceedP
TRANSPORT Decrypted at the IP eNodeB DSP IPSTAT
kt
Layer of the
Receiver
Total Number of
Packets Failed in
InEspDecryptFailPk
TRANSPORT ESP Decryption at eNodeB DSP IPSTAT
t
the IP Layer of the
Receiver Hardware
Total Number of
Packets Failed in
AH Authentication
TRANSPORT InAhAuthFailPkt eNodeB DSP IPSTAT
at the IP Layer of
the Receiver
Hardware
Total Number of
Packets Discarded
InShouldNotEncrypt at the IP Layer of
TRANSPORT eNodeB DSP IPSTAT
edPkt the Receiver Due to
Having Been
Encrypted
Total Number of
Packets Received
TRANSPORT InTotalPkt by the Decryption eNodeB DSP IPSTAT
Module of the
Receiver
Number of Failing
TRANSPORT InDecryptFailPkt Decrypted Packets eNodeB DSP IPSTAT
at the Receiver
Total Number of IKE

Packets Received
TRANSPORT InIkePkt eNodeB DSP IPSTAT
at the IP Layer of
the Receiver
Total Number of
Packets Discarded
InWrongSIPEncrypt at the IP Layer of
edPkt the Receiver Due to
Invalid Source IP
Addresses
Total Number of
Packets Discarded
InAntiReplayDropP
TRANSPORT at the IP Layer of eNodeB DSP IPSTAT
kt
the Receiver Due to
Replay Attacks
Total Number of
Packets Discarded
TRANSPORT InSaMissDropPkt at the IP Layer of eNodeB DSP IPSTAT
the Receiver Due to
No Inbound SA
Total Number of
Packets Discarded
InUnsupportAhAlgD at the IP Layer of
ropPkt the Receiver Due to
Unsupported AH
Algorithm
Total Number of
Packets Discarded
InUnsupportEspAlg at the IP Layer of
DropPkt the Receiver Due to
Unsupported ESP
Algorithm
Total Number of
Plain Packets
TRANSPORT InUnEncryptedPkt Received at the IP eNodeB DSP IPSTAT
Layer of the
Receiver
Number of Packets
Discarded at the IP
InShouldEncrypted
TRANSPORT Layer of the eNodeB DSP IPSTAT
Pkt
Receiver Due to not
Being Encrypted
Number of Packets
Successfully
OutEncryptSucceed
TRANSPORT Encrypted at the IP eNodeB DSP IPSTAT
Pkt
Layer of the
Transmitter
Total Number of
Packets Failed to
TRANSPORT OutEncryptFailPkt Be Encrypted at the eNodeB DSP IPSTAT
IP Layer of the
Transmitter
Total Number of
Packets Received
TRANSPORT OutTotalPkt by the Encryption eNodeB DSP IPSTAT
Module of the
Transmitter
Number of Packets
That Should be
TRANSPORT OutNeedEncryptPkt eNodeB DSP IPSTAT
Encrypted at the
Transmitter
Total Number of
Packets Discarded
TRANSPORT OutSaMissDropPkt at the IP Layer of eNodeB DSP IPSTAT
the Transmitter due
to No Outbound SA
Total Number of
Packets Discarded
OutUnsupportAhAlg at the IP Layer of
DropPkt the Transmitter Due
to Unsupported AH
Algorithm
Total Number of
Packets Discarded
OutUnsupportEspAl at the IP Layer of
gDropPkt the Transmitter Due
to Unsupported
ESP Algorithm
Total Number of
Packets Failed in
AH Authentication
TRANSPORT OutAhAuthFailPkt eNodeB DSP IPSTAT
at the IP Layer of
the Transmitter
Hardware
Total Number of
Packets Failed in
OutEspDecryptFail
TRANSPORT ESP Encryption at eNodeB DSP IPSTAT
Pkt
the IP Layer of the
Transmitter
Total Number of
Packets Discarded
OutSeqOverflowDro
TRANSPORT at the IP Layer of eNodeB DSP IPSTAT
pPkt
the Transmitter Due
to SN Overflow
Total Number of
Packets That
OutNoNeedEncrypt Should Not Have
Pkt Been Encrypted at
the IP Layer of the
Transmitter
Total Number of IKE
Packets Sent at the
TRANSPORT OutIkePkt eNodeB DSP IPSTAT
IP Layer of the
Transmitter
ADD TUNNEL
DSP TUNNEL
TUNNEL SCN Source Cabinet No. eNodeB MOD TUNNEL
RMV TUNNEL
LST TUNNEL
ADD TUNNEL
DSP TUNNEL
Source Subrack
TUNNEL SSRN eNodeB MOD TUNNEL
No.
RMV TUNNEL
LST TUNNEL
ADD TUNNEL
DSP TUNNEL
TUNNEL SSN Source Slot No. eNodeB MOD TUNNEL
RMV TUNNEL
LST TUNNEL
ADD TUNNEL
DSP TUNNEL
TUNNEL TUNNELID Tunnel No. eNodeB MOD TUNNEL
RMV TUNNEL
LST TUNNEL
ADD TUNNEL
Destination Cabinet MOD TUNNEL
TUNNEL DCN eNodeB
No. DSP TUNNEL
LST TUNNEL
ADD TUNNEL
Destination MOD TUNNEL
TUNNEL DSRN eNodeB
Subrack No. DSP TUNNEL
LST TUNNEL
ADD TUNNEL
MOD TUNNEL
TUNNEL DSN Destination Slot No. eNodeB
DSP TUNNEL
LST TUNNEL
Number of RX
TUNNEL RcvByte eNodeB DSP TUNNEL
Bytes
Number of RX
TUNNEL RcvPacket eNodeB DSP TUNNEL
Packets
Number of TX
TUNNEL SendByte eNodeB DSP TUNNEL
Bytes
Number of TX
TUNNEL SendPacket eNodeB DSP TUNNEL
Packets
ADD VLANCLASS
LST VLANCLASS
VLANCLASS VLANGROUPNO VLAN Group No. eNodeB
MOD VLANCLASS
RMV VLANCLASS
ADD VLANCLASS
MOD VLANCLASS
VLANCLASS TRAFFIC Traffic Type eNodeB
RMV VLANCLASS
LST VLANCLASS
ADD VLANCLASS
User Data Service MOD VLANCLASS
VLANCLASS SRVPRIO eNodeB
Priority RMV VLANCLASS
LST VLANCLASS
ADD VLANCLASS
VLANCLASS VLANID VLAN ID eNodeB MOD VLANCLASS
LST VLANCLASS
ADD VLANCLASS
VLANCLASS VLANPRIO VLAN Priority eNodeB MOD VLANCLASS
LST VLANCLASS
ADD VLANMAP
MOD VLANMAP
VLANMAP NEXTHOPIP Next Hop IP eNodeB
RMV VLANMAP
LST VLANMAP
ADD VLANMAP
MOD VLANMAP
VLANMAP MASK Mask eNodeB
RMV VLANMAP
LST VLANMAP
ADD VLANMAP
VLANMAP VLANMODE VLAN Mode eNodeB MOD VLANMAP
LST VLANMAP
ADD VLANMAP
VLANMAP VLANID VLAN ID eNodeB MOD VLANMAP
LST VLANMAP
ADD VLANMAP
VLANMAP VLANPRIO VLAN Priority eNodeB MOD VLANMAP
LST VLANMAP
ADD VLANMAP
VLANMAP VLANGROUPNO VLAN Group No. eNodeB MOD VLANMAP
LST VLANMAP
ADD VLANMAP
VLANMAP SETPRIO Set VLAN Priority eNodeB MOD VLANMAP
LST VLANMAP
ECHO Frame MOD GTPU
GTPU TIMEOUTTH eNodeB
Timeout LST GTPU
ECHO Frame MOD GTPU

GTPU TIMEOUTCNT eNodeB
Timeout Count LST GTPU
MOD GTPU
GTPU DSCP DSCP eNodeB
LST GTPU
MOD GTPU
GTPU STATICCHK Static Check Switch eNodeB
LST GTPU
Meaning IsKey Mandatory Dynamic Attribute Feature ID
Indicates the device

LOFD-001024 /
number of the BF YES YES No
TDLOFD-001024
antenna.
Indicates the
cabinet number of
LOFD-001024 /
the RRU NO NO No
TDLOFD-001024
connecting to the
BF antenna.
Indicates the
subrack number of
LOFD-001024 /
the RRU NO YES No
TDLOFD-001024
connecting to the
BF antenna.
Indicates the slot
number of the RRU LOFD-001024 /
NO NO No
connecting to the TDLOFD-001024
BF antenna.
Indicates the model LOFD-001024 /

NO NO No
of the BF antenna. TDLOFD-001024
Indicates the
LOFD-001024 /
configured tilt of the NO NO No
TDLOFD-001024
BF antenna.
Indicates the
LOFD-001024 /
beamwidth formed NO NO No
TDLOFD-001024
after beamforming.
Indicates the
frequency band in LOFD-001024 /
NO NO No
which the BF TDLOFD-001024
antenna operates.
Indicates the type LOFD-001024 /

NO NO No
of the BF antenna. TDLOFD-001024
Indicates the
LOFD-001024 /
polarization mode NO NO Yes
TDLOFD-001024
of the BF antenna.
Indicates the
LOFD-001024 /
beamwidth of the NO NO Yes
TDLOFD-001024
antenna element.
Indicates the
number of physical
antenna ports to LOFD-001024 /
NO NO Yes
which the BF TDLOFD-001024
antenna is
connected.
Indicates the
amplitude offset at
physical antenna
port 1 when the BF
LOFD-001024 /
antenna is used NO NO Yes
TDLOFD-001024
and cell-specific
reference signals
are transmitted from
two ports.
Indicates the phase

offset at physical
antenna port 1
when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the
amplitude offset at
physical antenna
port 2 when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the phase

offset at physical
antenna port 2
when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the
amplitude offset at
physical antenna
port 3 when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the phase

offset at physical
antenna port 3
when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the
amplitude offset at
physical antenna
port 4 when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the phase

offset at physical
antenna port 4
when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
two ports.
Indicates the
amplitude offset at
physical antenna
port 1 when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
four ports.
Indicates the phase

offset at physical
antenna port 1
when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
four ports.
Indicates the
amplitude offset at
physical antenna
port 2 when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
four ports.
Indicates the phase

offset at physical
antenna port 2
when the BF
LOFD-001024 /
TDLOFD-001024
and cell-specific
reference signals
four ports.
Indicates the ID of
the eNodeB, which
uniquely identifies
an eNodeB within a
PLMN(Public Land NO NO No None
Mobile Network).
This parameter is a
part of the CGI(Cell
Global Identifier).
Indicates the name

of the eNodeB,
which uniquely
NO NO No None
identifies an
eNodeB within a
PLMN.
Indicates the
NO NO No None
eNodeB type.
Indicates the switch

for automatically
powering on or off
the eNodeB. If the
switch is turned on,
the RF channels of
the RRUs/RFUs are
shut down. In this
situation, the
RRUs/RFUs work in NO NO No LOFD-001025
low power
consumption mode.
The RRUs/RFUs
are reset after the
eNodeB is powered
on automatically.
Then, the
RRUs/RFUs start to
carry services.
Indicates the
automatic power-off NO NO No LOFD-001025
time of the eNodeB.
Indicates the
automatic power-on NO NO No LOFD-001025
time of the eNodeB.
Indicates the
longitude of the
eNodeB. A negative
value indicates a
NO NO No None
west longitude, and
a positive value
indicates an east
longitude.
Indicates the
latitude of the
eNodeB. A negative
value indicates a
NO NO No None
south latitude, and
a positive value
indicates a north
latitude.
Indicates the ESN
of the eNodeB NO NO Yes None
backplane.
eNodeB enters the
demo license state
when a demo LKF
is installed on
eNodeB. In a
typical demo LKF,
resource items are
set to the maximum
values and function
items are all turned
on. When a demo
LKF expires, the
eNodeB status
changes from the
demo license state
to the protected
license state. An
eNodeB can stay in
the protected NO NO Yes None
license state for up
to 60 days. After 60
days elapse, the
eNodeB enters the
default license
state.
An operating
eNodeB enters the
protected license
state when any of
the following
conditions is met:1.
An Esn or Version
check on its LKF
fails. 2. Its demo
LKF expires. 3. Its
commercial LKF is
revoked. In the
Indicates whether
the eNodeB is
automatically
powered off. If this
parameter is
Poweroff, all
RRUs/RFUs in the
eNodeB enter the
NO NO Yes None
low power
consumption mode,
and all cells are
unavailable. If this
parameter is
Normal, the
eNodeB runs
normally.
Indicates the
position of the NO NO No None
eNodeB.
Indicates the format

of geographical NO NO No None
coordinates.
Indicates the
latitude of the
eNodeB in the NO NO No None
WGS-84 coordinate
system.
Indicates the
longitude of the
eNodeB in the NO NO No None
WGS-84 coordinate
system.
Indicates the
communication
protocol type used
between the BBU
and radio frequency
(RF) units. The
value CPRI
indicates the
Huawei proprietary
NO NO No None
protocol, and the
value TDL_IR
indicates the IR
communication
protocol defined by
China Mobile
Communication
Corporation
(CMCC).
Indicates the type
YES YES No None
of a KPI alarm.
Indicates whether
to report the KPI NO YES No None
alarm.
Indicates the
threshold for
generating a KPI
alarm. The
thresholds for delay
and variation on the
transport network
are expressed in
units of ms. The
thresholds for NO YES No None
packet loss rates on
the transport
network or on NE
ports are expressed
in units of
permillage. Other
alarm thresholds
are expressed in
units of percentage.
Indicates the
threshold for
clearing a KPI
alarm. The
thresholds for delay
and variation on the
transport network
are expressed in
units of ms. The
thresholds for NO YES No None
packet loss rates on
the transport
network or on NE
ports are expressed
in units of
permillage. Other
alarm thresholds
are expressed in
units of percentage.
Indicates the
minimum number of
KPI checks. If the
number of actual
checks is less than NO NO No None
the value of this
parameter, KPI
alarms are not
reported or cleared.
following ways: 1. If
the monitoring
period is set to 15
minutes, 30
minutes, or 60
minutes, the
configured start
time for monitoring
KPI alarms is
invalid. For
example, if a
command for a KPI
alarm monitoring is
started between
8:00 and 8:05
(excluding 8:05)
and the monitoring
period is 15
minutes, the KPIs
NO NO No None
generated between
8:00 and 8:15
(excluding 8:15) are
monitored. 2. If the
monitoring period is
set to one day, the
configured start
time for monitoring
KPI alarms is valid.
For example, if a
command for a KPI
alarm monitor is
started between
8:00 to 8:05
(excluding 8:05)
and the start time
for monitoring KPI
alarms is set to
8:00, the KPIs
Indicates the start
time for monitoring
KPI alarms. This
parameter is valid
only when the NO NO No None
monitoring period is
one day. The start
time must be on a
full hour.
Indicates the
number of detection NO NO No None
periods.
Indicates the sector

YES YES No None
number.
Indicates the
longitude of the
sector. A negative
value indicates a
NO YES No None
west longitude, and
a positive value
indicates an east
longitude.
Indicates the
latitude of the
sector. A negative
value indicates a
NO YES No None
south latitude, and
a positive value
indicates a north
latitude.
Indicates the
antenna mode of NO YES No None
the sector.
Indicates the
multiple-input
multiple-output
(MIMO) mode of the NO NO No LOFD-001038
sector, which can
be normal MIMO or
mutual-aid MIMO.
Indicates the
combination mode NO NO No None
of the sector.
Indicates the
cabinet number of
the RRU where the NO YES No None
antenna port 1 is
located.
Indicates the
subrack number of
the RRU where the NO YES No None
antenna port 1 is
located.
Indicates the slot
number of the RRU
NO YES No None
where the antenna
port 1 is located.
Indicates the port
number of the NO YES No None
antenna port 1.
Indicates the
cabinet number of
the RRU where the NO NO No None
antenna port 2 is
located.
Indicates the
subrack number of
antenna port 2 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 2 is located.
Indicates the port

number of the NO NO No None
antenna port 2.
Indicates the
cabinet number of
antenna port 3 is
located.
Indicates the
subrack number of
antenna port 3 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 3 is located.
Indicates the port
antenna port 3.
Indicates the
cabinet number of
antenna port 4 is
located.
Indicates the
subrack number of
antenna port 4 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 4 is located.
Indicates the port

antenna port 4.
Indicates the
cabinet number of
antenna port 5 is
located.
Indicates the
subrack number of
antenna port 5 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 5 is located.
Indicates the port
antenna port 5.
Indicates the
cabinet number of
antenna port 6 is
located.
Indicates the
subrack number of
antenna port 6 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 6 is located.
Indicates the port

antenna port 6.
Indicates the
cabinet number of
antenna port 7 is
located.
Indicates the
subrack number of
antenna port 7 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 7 is located.
Indicates the port
antenna port 7.
Indicates the
cabinet number of
antenna port 8 is
located.
Indicates the
subrack number of
antenna port 8 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 8 is located.
Indicates the port

antenna port 8.
Indicates the
cabinet number of
antenna port 9 is
located.
Indicates the
subrack number of
antenna port 9 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 9 is located.
Indicates the port
antenna port 9.
Indicates the
cabinet number of
antenna port 10 is
located.
Indicates the
subrack number of
antenna port 10 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 10 is located.
Indicates the port

antenna port 10.
Indicates the
cabinet number of
antenna port 11 is
located.
Indicates the
subrack number of
antenna port 11 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 11 is located.
Indicates the port
antenna port 11.
Indicates the
cabinet number of
antenna port 12 is
located.
Indicates the
subrack number of
antenna port 12 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 12 is located.
Indicates the port

antenna port 12.

name, which is a
string of a NO NO No None
maximum of 30
characters.
Indicates the
altitude of the
sector in the WGS-
84 coordinate
system. If the value
is greater than 0,
the sector is above
the ellipsoid surface
in the WGS-84
coordinate system. NO YES No None
If the value is less
than 0, the sector is
below the ellipsoid
surface in the
WGS-84 coordinate
system. For details,
see 3GPP TS
23.032 and 3GPP
TS 36.455.
Indicates the semi-

major axis length of
the uncertainty area
by which the
geographical
location of the
antennas in the
sector is to be
included. The
NO NO No None
smaller the
parameter value is,
the higher the
positioning
accuracy is. For
details about the
uncertainty area,
see 3GPP TS
23.032.
Indicates the semi-

minor axis length of
the uncertainty area
by which the
geographical
location of the
antennas in the
sector is to be
included. The
NO NO No None
smaller the
parameter value is,
the higher the
positioning
accuracy is. For
details about the
uncertainty area,
see 3GPP TS
23.032.
Indicates the major
axis orientation of
an uncertainty area
by which the
geographical
location of the
antennas in the
sector is to be
included. (The
orientation is the
counter-clockwise
angle in degrees NO NO No None
between the major
axis and north). The
smaller the
parameter value is,
the higher the
positioning
accuracy is. For
details about the
uncertainty area,
see 3GPP TS
23.032.
Indicates the
altitude of an
uncertainty area by
which the
geographical
location of the
antennas in the
sector is to be
included. The
altitude is in the
NO NO No None
WGS-84 coordinate
system. The smaller
the parameter value
is, the higher the
positioning
accuracy is. For
details about the
uncertainty area,
see 3GPP TS
23.032.
Indicates the
confidence level of
an uncertainty area
by which the
geographical
location of the
antennas in the
sector is to be
included. The
NO NO No None
smaller the
parameter value is,
the higher the
positioning
accuracy is. For
details about the
uncertainty area,
see 3GPP TS
23.032.
Indicates the format

of geographical NO NO No None
coordinates.
Indicates the
latitude of the
sector in the WGS- NO NO No None
84 coordinate
system.
Indicates the
longitude of the
sector in the WGS- NO NO No None
84 coordinate
system.
Indicates the flag of

the omnidirectional
cell. If this
parameter is set to
TRUE, the cell is an
NO NO No None
omnidirectional cell.
If this parameter is
set to FALSE, the
cell is not an
omnidirectional cell.
Indicates the
cabinet number of
antenna port 13 is
located.
Indicates the
subrack number of
antenna port 13 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 13 is located.
Indicates the port
antenna port 13.
Indicates the
cabinet number of
antenna port 14 is
located.
Indicates the
subrack number of
antenna port 14 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 14 is located.
Indicates the port

antenna port 14.
Indicates the
cabinet number of
antenna port 15 is
located.
Indicates the
subrack number of
antenna port 15 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 15 is located.
Indicates the port
antenna port 15.
Indicates the
cabinet number of
antenna port 16 is
located.
Indicates the
subrack number of
antenna port 16 is
located.
Indicates the slot
number of the RRU
NO NO No None
where the antenna
port 16 is located.
Indicates the port

antenna port 16.
Indicates the
maximum output
power that can be
configured for each
TX channel of the
sector. This
parameter is
specified based on
the capabilities of NO NO Yes None
all TX channels
configured for the
sector. It is set to
the minimum value
among the
maximum output
power of all TX
channels.
Indicates whether a
license is granted to
the sector. A license NO NO Yes None
is required only by
a dual-mode sector.
Indicates the range

of RX channel
frequencies
supported by the
sector. This
parameter is set to
the frequency band
between the
minimum and
maximum
frequencies on the
RX channels of the
RRU where the
antenna ports are
located. If a sector
is configured on NO NO Yes None
multiple RRUs, the
frequency band
supported by the
sector is the
intersection of
frequency bands
supported by the
RRUs. If a sector is
configured on a
single RRU, the
frequency band of
the sector is the
frequency band
supported by the
RRU.
Indicates the range
of TX channel
frequencies
supported by the
sector. This
parameter is set to
the frequency band
between the
minimum and
maximum
frequencies on the
TX channels of the
RRU where the
antenna ports are
located. If a sector
is configured on NO NO Yes None
multiple RRUs, the
frequency band
supported by the
sector is the
intersection of
frequency bands
supported by the
RRUs. If a sector is
configured on a
single RRU, the
frequency band of
the sector is the
frequency band
supported by the
RRU.
Indicates the policy
for logging in to the
Web LMT.
The value
COMPATIBLE
indicates that if http
is entered on the
IE, the policy for
logging in to the
WebLMT is http,
and if https is
entered on the IE,
the policy for
logging in to the
WebLMT is https.
The value
HTTPS_ONLY
NO NO No None
indicates that
whether http or
https is entered on
the IE, the policy for
logging in to the
WebLMT is https.
The value
LOGIN_HTTPS_O
NLY indicates that
whether http or
https is entered on
the IE, the policy for
logging in to the
WebLMT is https,
and then the policy
turns to http after
the logging.

number of the ALD.
LOFD-001024 /
The device number YES YES No
TDLOFD-001024
of the ALD must be
unique.
Indicates the
vendor code of the LOFD-001024 /
NO NO Yes
device in the TDLOFD-001024
scanning result.
Indicates the serial
number of the LOFD-001024 /
NO NO Yes
scanning result.
name of the ALD,
which identifies the
ALD. The format of
the name is as
follows:
site_sector_device
type_network type.
The meanings of
the parts are as
follows: Site:
indicates the
number of the BS
site. It is uniformly
assigned during the
network planning.
Sector: indicates
the number of the
sector. It is unique
LOFD-001024 /
within a site. Device NO NO No
TDLOFD-001024
type: indicates the
type of currently
connected device. It
can be
SINGLE_RET
(Single-antenna
Remote Electrical
Tilt Unit),
MULTI_RET (Multi-
antenna Remote
Electrical Tilt Unit),
TMA (Tower-
mounted Amplifier).
Network type:
indicates whether
the current ALD is
used for a 2G
network or 3G/LTE
Indicates the
cabinet number of
LOFD-001024 /
the RRU or RFU NO NO No
TDLOFD-001024
that controls the
ALD.
Indicates the
subrack number of
LOFD-001024 /
the RRU or RFU NO YES No
TDLOFD-001024
that controls the
ALD.
Indicates the slot
NO YES No
or RFU that controls TDLOFD-001024
the ALD.
Indicates the actual

protocol version of
the ALD. NULL
LOFD-001024 /
means that the NO NO Yes
TDLOFD-001024
protocol version
information fails to
be obtained.
Indicates the total
LOFD-001024 /
number of ALD NO NO Yes
TDLOFD-001024
subunits.
Indicates the LOFD-001024 /

NO NO No
vendor code. TDLOFD-001024

number of the ALD.
The vendor code LOFD-001024 /
NO NO No
and the serial TDLOFD-001024
number uniquely
identify an ALD.
Indicates the
version information LOFD-001024 /
NO NO Yes
about the ALD TDLOFD-001024
hardware.
Indicates the
NO NO Yes
software.
Indicates the device LOFD-001024 /
NO NO Yes
model of the ALD. TDLOFD-001024

NO NO Yes
type of the ALD. TDLOFD-001024
Indicates the port
number of the RRU
or RFU that controls
the ALD. It will be
NO NO Yes None
NULL if the
RRU/RFU does not
support to report
this parameter.
Indicates the
cabinet number of
LOFD-001024 /
the RRU or RFU YES NO No
TDLOFD-001024
where the antenna
port is located.
Indicates the
subrack number of
LOFD-001024 /
the RRU or RFU YES YES No
TDLOFD-001024
where the antenna
port is located.
Indicates the slot

number of the RRU
LOFD-001024 /
or RFU where the YES YES No
TDLOFD-001024
antenna port is
located.
Indicates the
YES YES No
antenna port on the TDLOFD-001024
RRU or RFU.
Indicates the length
of the feeder at the NO NO No None
antenna port.
Indicates the DL
delay of the TMA. It
should be specified
according to the
specification LOFD-001024 /
NO NO No
provided by the TDLOFD-001024
manufacturer.
Typically, this
parameter is
smaller than 30 ns.
Indicates the UL
delay of the TMA. It
should be specified
according to the
specification LOFD-001024 /
NO NO No
provided by the TDLOFD-001024
manufacturer.
Typically, this
parameter is
smaller than 30 ns.
Indicates the state

of the ALD power
supply switch. The
ALD power supply
switches for the
SINGLE_RET
(Single-antenna
Remote Electrical
Tilt), MULTI_RET
(Multi-antenna
Remote Electrical
Tilt), and STMA
(Smart Tower-
mounted LOFD-001024 /
NO NO No
Amplifier)must be TDLOFD-001024
set to ON. In actual
running, the system
may automatically
set the ALD power
supply switch of the
antenna port to
OFF when an ALD
current abnormal
alarm is reported.
For details, see
ALM-26530 RF
Module ALD
Current Abnormal.
Occur Threshold is
40 mA, the
Undercurrent Alarm
Clear Threshold is
60 mA, the
Overcurrent Occur
Alarm Threshold is
310 mA, and the
Overcurrent Alarm
Clear Threshold is
280 mA. For RET
(coaxial) only: the
Undercurrent Alarm
Occur Threshold is
25 mA, the
Undercurrent Alarm
Clear Threshold is
33 mA, the
Overcurrent Occur LOFD-001024 /
NO NO No
Alarm Threshold is TDLOFD-001024
150 mA, and the
Overcurrent Alarm
Clear Threshold is
120 mA. For 12 dB
TMA and RET or 12
dB TMA (AISG)
only: the
Undercurrent Alarm
Occur Threshold is
30 mA, the
Undercurrent Alarm
Clear Threshold is
40 mA, the
Overcurrent Occur
Alarm Threshold is
450 mA, and the
Overcurrent Alarm
Clear Threshold is
Indicates the
undercurrent alarm
occur threshold.
When the ALD
current value is
smaller than this
LOFD-001024 /
threshold, an ALM- NO NO No
TDLOFD-001024
26530 RF Module
ALD Current
Abnormal alarm is
reported. The
specific problem is
undercurrent.
Indicates the
undercurrent alarm
clear threshold.
When the ALD
current value is
LOFD-001024 /
greater than this NO NO No
TDLOFD-001024
threshold, the ALM-
26530 RF Module
ALD Current
Abnormal alarm is
cleared.
Indicates the
overcurrent alarm
occur threshold.
When the ALD
current value is
greater than this
threshold, an ALM-
26530 RF Module
ALD Current
Abnormal alarm is
reported. The
specific problem is
overcurrent. When
the overcurrent
alarm occur
threshold is lower
than the maximum
LOFD-001024 /
current supported NO NO No
TDLOFD-001024
by the hardware,
the overcurrent
alarm occur
threshold prevails.
When the
overcurrent alarm
occur threshold is
higher than the
maximum current
supported by the
hardware, the
maximum current
supported by the
hardware serves as
the overcurrent
alarm occur
threshold.
Indicates the
overcurrent alarm
clear threshold.
When the ALD
current value is
smaller than this
threshold, the ALM-
26530 RF Module
ALD Current
Abnormal alarm is
cleared. When the
overcurrent alarm
clear threshold is
lower than the
maximum value of
current supported
LOFD-001024 /
by the hardware, NO NO No
TDLOFD-001024
the overcurrent
alarm clear
threshold prevails.
When the
overcurrent alarm
clear threshold is
higher than the
maximum current
supported by the
hardware, the
maximum current
supported by the
hardware serves as
the overcurrent
alarm clear
threshold.
Indicates the
LOFD-001024 /
present value of the NO NO Yes
TDLOFD-001024
current of the ALD.
status of the ALD LOFD-001024 /
NO NO Yes
power supply TDLOFD-001024
switch.
Indicates the
antenna type. This
LOFD-001024 /
parameter can be NO YES No
TDLOFD-001024
set to SINGLE_RET
or MULTI_RET.
Indicates the
polarization type of
the antenna. This LOFD-001024 /
NO YES No
parameter can be TDLOFD-001024
set to SINGLE or
DUAL.
Indicates the
connection scenario
of the antenna. This
parameter must be
set based on the
hardware
installation. The
vendor code and LOFD-001024 /
NO YES No
serial number of the TDLOFD-001024
device must be
correctly configured
in a non-regular
scenario. This
parameter can be
set to REGULAR,
DAISY_CHAIN.
Indicates the
number of LOFD-001024 /
NO NO No
configured RET TDLOFD-001024
subunits.
Indicates the type
of the RET whose
NO NO Yes None
tilt needs to be
adjusted.
number of the ALD.
LOFD-001024 /
TDLOFD-001024
of the ALD must be
unique.
Indicates the
NO NO Yes
scanning result.
NO NO Yes
scanning result.
name of the ALD,
ALD. The format of
the name is as
follows:
site_sector_device
type_network type.
The meanings of
the parts are as
follows: Site:
indicates the
number of the BS
assigned during the
network planning.
Sector: indicates
the number of the
LOFD-001024 /
TDLOFD-001024
type: indicates the
type of currently
can be
SINGLE_RET
(Single-antenna
Remote Electrical
Tilt Unit),
MULTI_RET (Multi-
antenna Remote
TMA (Tower-
mounted Amplifier).
Network type:
indicates whether
the current ALD is
used for a 2G
network or 3G/LTE
Indicates the
cabinet number of
LOFD-001024 /
TDLOFD-001024
that controls the
ALD.
Indicates the
subrack number of
LOFD-001024 /
TDLOFD-001024
that controls the
ALD.
Indicates the slot
NO YES No
the ALD.

protocol version of
the ALD. NULL
LOFD-001024 /
TDLOFD-001024
protocol version
be obtained.
Indicates the total
LOFD-001024 /
TDLOFD-001024
subunits.

NO NO No

number of the ALD.
NO NO No
number uniquely
identify an ALD.
Indicates the
NO NO Yes
hardware.
Indicates the
NO NO Yes
software.
NO NO Yes

NO NO Yes
Indicates the port
number of the RRU
the ALD. It will be
NO NO Yes None
NULL if the
RRU/RFU does not
support to report
this parameter.

YES YES No
number of the RET. TDLOFD-001024
Indicates the RET

subunit number. LOFD-001024 /
YES YES No
The number starts TDLOFD-001024
from 1.

NO NO No
antenna azimuth. TDLOFD-001024
Indicates the model

LOFD-001024 /
of the RET antenna NO NO No
TDLOFD-001024
module.
Indicates the base

station ID.AISG1.1-
based RET
antennas support a
maximum sector ID
length of 4
LOFD-001024 /
characters. If the NO NO No
TDLOFD-001024
input sector ID has
more than 4
characters, only the
first 4 characters
are saved on the
RET antenna.
Indicates the
beamwidth of band
1. Beamwidth is
used to describe
the capability of the LOFD-001024 /
NO NO No
antenna to transmit TDLOFD-001024
RF signals. It is also
used to measure
the antenna
pattern.
Indicates the
beamwidth of band
2. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.
Indicates the
beamwidth of band
3. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.
Indicates the
beamwidth of band
4. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.
Indicates the gain LOFD-001024 /

NO NO No
of band 1. TDLOFD-001024

NO NO No

NO NO No

NO NO No
Indicates the date
LOFD-001024 /
when the antenna NO NO No
TDLOFD-001024
is installed.
Indicates the
LOFD-001024 /
mechanical tilt of NO NO No
TDLOFD-001024
the installation.
Indicates the ID of
the installation
LOFD-001024 /
technician who NO NO No
TDLOFD-001024
installed the
antenna.
Indicates band 1
LOFD-001024 /
supported by the NO NO No
TDLOFD-001024
antenna.
Indicates band 2
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates band 3
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates band 4
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates the sector LOFD-001024 /

NO NO No
ID. TDLOFD-001024
Indicates the serial LOFD-001024 /

NO NO No
number of the ALD. TDLOFD-001024
Indicates the
maximum tilt LOFD-001024 /
NO NO Yes
supported by the TDLOFD-001024
RET subunit.
Indicates the
minimum tilt LOFD-001024 /
NO NO Yes
RET subunit.
Indicates supported
NO NO Yes None
band 1.
Indicates supported
NO NO Yes None
band 2.
Indicates supported
NO NO Yes None
band 3.
Indicates supported
NO NO Yes None
band 4.
Indicates the
beamwidth of band
1. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
defines the width of
the antenna
pattern.
Indicates the
beamwidth of band
2. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the
beamwidth of band
3. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the
beamwidth of band
4. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the gain
NO NO Yes None
of band 1.
Indicates the gain
NO NO Yes None
of band 2.
Indicates the gain
NO NO Yes None
of band 3.
Indicates the gain
NO NO Yes None
of band 4.
Indicates the
cabinet number of LOFD-001024 /
YES YES No
the RRU where the TDLOFD-001024
RET port is located.
Indicates the
subrack number of LOFD-001024 /
YES YES No
the RRU where the TDLOFD-001024
RET port is located.
Indicates the slot
YES YES No
where the RET port TDLOFD-001024
is located.
Indicates the
number of the RET
antenna port on an LOFD-001024 /
YES YES No
RRU. This TDLOFD-001024
parameter is set to
RET_PORT.
Indicates the state
of the ALD power
supply switch. If
SINGLE_RET(Singl
e-antenna Remote
Electrical Tilt) or
MULTI_RET(Multi-
antenna Remote
Electrical Tilt) is
used, the ALD
power supply switch
must be set to ON.
In actual running,
the RRU/RFU
automatically sets
this switch to OFF
for an RET port
when the ALM-
26530 RF Module LOFD-001024 /
NO NO No
ALD Current TDLOFD-001024
Abnormal alarm is
reported due to
overcurrent,
overcurrent
protection, or
undercurrent
protection (the
RRU/RFU supports
undercurrent
protection and Low
Current Protect
Switch is set to ON
for the RRU/RFU)
on the RET port.
For details, see
ALM-26530 RF
Module ALD
Current Abnormal.
Indicates the type
of the ALD current
alarm threshold.
The current alarm
threshold for the
ALDs (excluding
user-defined ALDs),
that is, for RET
antennas only
(multi-wire cable),
must be selected
according to the
ALD type. The
Undercurrent Alarm
Occur Threshold is
LOFD-001024 /
10 mA, the NO NO No
TDLOFD-001024
Undercurrent Alarm
Clear Threshold is
15 mA, the
Overcurrent Alarm
Occur Threshold is
150 mA, and the
Overcurrent Alarm
Clear Threshold is
120 mA. This
parameter can be
set to
UER_SELF_DEFIN
E or
RET_ONLY_MULTI
CORE.
Indicates the
undercurrent alarm
occur threshold.
When the ALD
current value is
smaller than this
LOFD-001024 /
threshold, an ALM- NO NO No
TDLOFD-001024
26530 RF Module
ALD Current
Abnormal alarm is
reported. The
specific problem is
undercurrent.
Indicates the
undercurrent alarm
clear threshold.
When the ALD
current value is
LOFD-001024 /
greater than this NO NO No
TDLOFD-001024
threshold, the ALM-
26530 RF Module
ALD Current
Abnormal alarm is
cleared.
Indicates the
overcurrent alarm
occur threshold.
When the ALD
current value is
greater than this
threshold, an ALM-
26530 RF Module
ALD Current
Abnormal alarm is
reported. The
specific problem is
overcurrent. When
the overcurrent
alarm occur
threshold is lower
than the maximum
LOFD-001024 /
current supported NO NO No
TDLOFD-001024
by the hardware,
the overcurrent
alarm occur
threshold prevails.
When the
overcurrent alarm
occur threshold is
higher than the
maximum current
supported by the
hardware, the
maximum current
supported by the
hardware serves as
the overcurrent
alarm occur
threshold.
Indicates the
overcurrent alarm
clear threshold.
When the ALD
current value is
smaller than this
threshold, the ALM-
26530 RF Module
ALD Current
Abnormal alarm is
cleared. When the
overcurrent alarm
clear threshold is
lower than the
maximum value of
current supported
LOFD-001024 /
by the hardware, NO NO No
TDLOFD-001024
the overcurrent
alarm clear
threshold prevails.
When the
overcurrent alarm
clear threshold is
higher than the
maximum current
supported by the
hardware, the
maximum current
supported by the
hardware serves as
the overcurrent
alarm clear
threshold.
Indicates the
LOFD-001024 /
present value of the NO NO Yes
TDLOFD-001024
current of the ALD.
status of the ALD LOFD-001024 /
NO NO Yes
power supply TDLOFD-001024
switch.

YES YES No
number of the RET. TDLOFD-001024
Indicates the
number of the RET
LOFD-001024 /
subunit. The YES YES No
TDLOFD-001024
number starts from
1.
Indicates the online
LOFD-001024 /
status of the NO NO Yes
TDLOFD-001024
subunit.

LOFD-001024 /
tilt of the RET NO NO Yes
TDLOFD-001024
subunit.
ID of the RET NO NO Yes None
subunit.
Indicates the
cabinet number of
LOFD-001024 /
TDLOFD-001024
that is connected to
antenna port 1.
Indicates the
subrack number of
LOFD-001024 /
TDLOFD-001024
antenna port 1.
Indicates the slot
number of the RRU
LOFD-001024 /
or RFU that is NO NO No
TDLOFD-001024
connected to
antenna port 1.
Indicates the port

number of the RRU
LOFD-001024 /
or RFU that is NO NO No
TDLOFD-001024
connected to
antenna port 1.
Indicates the
cabinet number of
the RRU or RFU
LOFD-001024 /
antenna port 2. This NO NO No
TDLOFD-001024
parameter is valid
when a dual-
polarized antenna
is used.
Indicates the
subrack number of
the RRU or RFU
LOFD-001024 /
TDLOFD-001024
parameter is valid
when a dual-
polarized antenna
is used.
Indicates the slot
number of the RRU
or RFU that is
connected to
LOFD-001024 /
TDLOFD-001024
parameter is valid
when a dual-
polarized antenna
is used.
Indicates the port

number of RRU that
is connected to
antenna port 2. This LOFD-001024 /
NO NO No
parameter is valid TDLOFD-001024
when a dual-
polarized antenna
is used.
Indicates the
LOFD-001024 /
antenna tilt of the NO NO No
TDLOFD-001024
RET subunit.
Indicates the
allowed maximum
tilt inconsistency.
When the difference
between the actual
tilt of an RET
subunit and
configured tilt is
LOFD-001024 /
larger than the NO NO No
TDLOFD-001024
value of this
parameter, ALM-
26757 RET
Antenna Running
Data and
Configuration
Mismatch is
reported.
Indicates the name LOFD-001024 /

NO NO No
of the RET subunit. TDLOFD-001024
Indicates the
NO YES No
configured TMA TDLOFD-001024
subunits.
number of the ALD.
LOFD-001024 /
TDLOFD-001024
of the ALD must be
unique.
Indicates the
NO NO Yes
scanning result.
NO NO Yes
scanning result.
name of the ALD,
ALD. The format of
the name is as
follows:
site_sector_device
type_network type.
The meanings of
the parts are as
follows: Site:
indicates the
number of the BS
assigned during the
network planning.
Sector: indicates
the number of the
LOFD-001024 /
TDLOFD-001024
type: indicates the
type of currently
can be
SINGLE_RET
(Single-antenna
Remote Electrical
Tilt Unit),
MULTI_RET (Multi-
antenna Remote
TMA (Tower-
mounted Amplifier).
Network type:
indicates whether
the current ALD is
used for a 2G
network or 3G/LTE
Indicates the
cabinet number of
LOFD-001024 /
TDLOFD-001024
that controls the
ALD.
Indicates the
subrack number of
LOFD-001024 /
TDLOFD-001024
that controls the
ALD.
Indicates the slot
NO YES No
the ALD.

protocol version of
the ALD. NULL
LOFD-001024 /
TDLOFD-001024
protocol version
be obtained.
Indicates the total
LOFD-001024 /
TDLOFD-001024
subunits.

NO NO No

number of the ALD.
NO NO No
number uniquely
identify an ALD.
Indicates the
NO NO Yes
hardware.
Indicates the
NO NO Yes
software.
NO NO Yes

NO NO Yes
Indicates the port
number of the RRU
the ALD. It will be
NO NO Yes None
NULL if the
RRU/RFU does not
support to report
this parameter.

YES YES No
number of the TMA. TDLOFD-001024
Indicates the
number of the TMA
subunit. The
number starts from LOFD-001024 /
YES YES No
1. The subunit TDLOFD-001024
shares the same
HDLC address with
the ALD.

NO NO No
antenna azimuth. TDLOFD-001024
Indicates the base LOFD-001024 /

NO NO No
station ID. TDLOFD-001024
Indicates the
beamwidth of band
1. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.
Indicates the
beamwidth of band
2. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.
Indicates the
beamwidth of band
3. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.
Indicates the
beamwidth of band
4. Beamwidth is
used to describe
NO NO No
used to measure
the antenna
pattern.

NO NO No

NO NO No

NO NO No

NO NO No
Indicates the date

LOFD-001024 /
when the antenna NO NO No
TDLOFD-001024
is installed.
Indicates the
LOFD-001024 /
mechanical tilt of NO NO No
TDLOFD-001024
the installation.
Indicates the ID of
the installation
LOFD-001024 /
technician who NO NO No
TDLOFD-001024
installed the
antenna.
Indicates band 1
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates band 2
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates band 3
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates band 4
LOFD-001024 /
TDLOFD-001024
antenna.
Indicates the sector LOFD-001024 /

NO NO No
ID. TDLOFD-001024
Indicates the serial LOFD-001024 /

NO NO No
number of the ALD. TDLOFD-001024
Indicates the model

of the RET antenna LOFD-001024 /
NO NO No
connected to the TDLOFD-001024
TMA.
Indicates the
maximum gain LOFD-001024 /
NO NO Yes
TMA.
Indicates the
minimum gain LOFD-001024 /
NO NO Yes
TMA.
Indicates the type

of TMA subunit. It
indicates whether
the VS NO NO Yes None
measurement and
the bypass mode
are supported.
Indicates the step

for the TMA gain NO NO Yes None
change.
Indicates band 1
supported by the NO NO Yes None
antenna.
Indicates band 2
antenna.
Indicates band 3
antenna.
Indicates band 4
antenna.
Indicates the
beamwidth of band
1. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the
beamwidth of band
2. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the
beamwidth of band
3. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the
beamwidth of band
4. Beamwidth
describes the
capability of an
NO NO Yes None
antenna to transmit
RF signals. It also
the antenna
pattern.
Indicates the gain
NO NO Yes None
of band 1.
Indicates the gain
NO NO Yes None
of band 2.
Indicates the gain
NO NO Yes None
of band 3.
Indicates the gain
NO NO Yes None
of band 4.
Indicates the
minimum RX
frequency band NO NO Yes None
supported by the
TMA.
Indicates the
maximum TX
supported by the
TMA.
Indicates the
minimum TX
supported by the
TMA.
Indicates the
maximum RX
supported by the
TMA.

YES YES No
number of the TMA. TDLOFD-001024
Indicates the
number of the TMA LOFD-001024 /
YES YES No
subunit, which TDLOFD-001024
starts from 1.
LOFD-001024 /
ID of the TMA NO NO Yes
TDLOFD-001024
subunit.
LOFD-001024 /
gain of the TMA NO NO Yes
TDLOFD-001024
subunit.

LOFD-001024 /
working mode of NO NO Yes
TDLOFD-001024
the TMA subunit.
Indicates the online
LOFD-001024 /
status of the TMA NO NO Yes
TDLOFD-001024
subunit.
Indicates the
number of the
antenna port to LOFD-001024 /
NO NO No
which the TMA TDLOFD-001024
subunit is
connected.
Indicates the
cabinet number of
the RRU or RFU
that provides the LOFD-001024 /
NO NO No
antenna port to TDLOFD-001024
which the TMA
subunit is
connected.
Indicates the slot

number of the RRU
or RFU that
provides the LOFD-001024 /
NO NO No
which the TMA
subunit is
connected.
Indicates the
subrack number of
the RRU or RFU
that provides the LOFD-001024 /
NO NO No
which the TMA
subunit is
connected.
Indicates the gain

of the TMA
subunit.If this
LOFD-001024 /
parameter is set to NO NO No
TDLOFD-001024
255, it is invalid and
the actual gain is
not changed.
Indicates the
working mode of
the TMA subunit. If
the TMA subunit
works in BYPASS
mode, it does not
amplify the uplink LOFD-001024 /
NO NO No
signals.If this TDLOFD-001024
parameter is set to
DEVICE_DEFAULT
_VALUE, it is invalid
and the actual
mode is not
changed.
Indicates the
cabinet number of
the AAU where the YES YES No None
virtual antenna port
is located.
Indicates the
subrack number of
the AAU where the YES YES No None
is located.
Indicates the slot
number of the AAU
where the virtual YES YES No None
antenna port is
located.
Indicates the
number of the YES YES No None
virtual antenna port.

number of the
YES YES No None
virtual RET
antenna.
Indicates the
cabinet number of
the AAU where the NO YES No None
virtual RET antenna
is located.
Indicates the
subrack number of
virtual RET antenna
is located.
Indicates the slot
number of the AAU
where the virtual NO YES No None
RET antenna is
located.

name of the virtual NO YES No None
RET antenna.
Indicates the
number of subunits
contained in the NO NO No None
virtual RET
antenna.
Indicates the
cabinet number of
virtual RET subunit
is located.
Indicates the
number of the first
NO NO No None
to which the virtual
RET subunit is
connected.
Indicates the
number of the
second virtual
antenna port to NO NO No None
which the virtual
RET subunit is
connected.

name of the virtual NO YES No None
RET subunit.
number of the
virtual RET antenna
YES YES No None
where the virtual
RET subunit is
contained.
Indicates the
the virtual antenna
NO NO No None
port 1 to which the
virtual RET subunit
is connected.
Indicates the slot

number of the AAU
where the virtual NO YES No None
RET subunit is
located.
Indicates the
subrack number of
virtual RET subunit
is located.
Indicates the
virtual RET subunit.
Indicates the
number of the third
NO NO No None
to which the virtual
RET subunit is
connected.
Indicates the
the virtual antenna
NO NO No None
port 2 to which the
virtual RET subunit
is connected.
Indicates the
downlink tilt of the
virtual RET subunit.
NO NO No None
set to 32767, it is
invalid and the
actual tilt is not
changed.
Indicates the uplink

tilt of the virtual
RET subunit. If this
parameter is set to NO NO No None
32767, it is invalid
and the actual tilt is
not changed.
Indicates the
number of the
fourth virtual
antenna port to NO NO No None
which the virtual
RET subunit is
connected.
Indicates the
the virtual antenna
NO NO No None
port 3 to which the
virtual RET subunit
is connected.
Indicates the
the virtual antenna
NO NO No None
port 4 to which the
virtual RET subunit
is connected.
Indicates the
number of ports
that can be added NO NO No None
to a virtual RET
subunit.
Indicates the
number of the
YES YES No None
control link at the
local end.
Indicates the
cabinet number of
the local node at NO YES No None
one end of the
control link.
Indicates the
subrack number of
the local node at NO YES No None
one end of the
control link.
Indicates the slot
number of the local
NO YES No None
node at one end of
the control link.
Indicates the
cabinet number of
the upper-level
NO YES No None
node at the other
end of the control
link.
Indicates the
subrack number of
the upper-level
NO YES No None
node at the other
end of the control
link.
Indicates the slot
number of the
upper-level node at NO YES No None
the other end of the
control link.
Indicates the port

number of the
upper-level node at
the other end of the
NO YES No None
control link.Values 0
to 4 indicate the
ports M0 to M4 on
the board panel.
Indicates the
number of the port
whose control link
status is queried.
When this
parameter is set to
a value within the
range from 0 to 4,
this parameter
NO NO Yes None
indicates a primary
port on the UCIU
board. When this
parameter is set to
8, this parameter
indicates the
secondary port on
the UCIU and
UMPT board.
Indicates the start

time of the NO NO Yes None
measurement.
Indicates the
number of error
packets within the
NO NO Yes None
measurement
periods in the latest
one day.
Indicates the ratio
of the number of
error packets to that
of received packets
NO NO Yes None
within the
measurement
one day.
Indicates the ratio

of the Loss Of
Signal (LOS)
duration to one day.
The LOS duration is NO NO Yes None
measured within
the measurement
one day.
Indicates the Loss

Of Signal (LOS)
duration measured
within the NO NO Yes None
measurement
one day.
Indicates the
number of error
packets within the
NO NO Yes None
measurement
one hour.
Indicates the ratio

of the number of
of received packets
NO NO Yes None
within the
measurement
one hour.
Indicates the ratio
of the Loss Of
Signal (LOS)
duration to one
hour. The LOS
NO NO Yes None
duration is
measured within
the measurement
one hour.
Indicates the Loss
Of Signal (LOS)
duration measured
measurement
one hour.
Indicates the
number of error
packets within the
NO NO Yes None
measurement
one week.
Indicates the ratio

of the number of
of received packets
NO NO Yes None
within the
measurement
one week.
Indicates the ratio
of the Loss Of
Signal (LOS)
duration to one
week. The LOS
NO NO Yes None
duration is
measured within
the measurement
one week.
Indicates the Loss
Of Signal (LOS)
duration measured
measurement
one week.
Indicates the total

number of error
packets within the NO NO Yes None
measurement
periods.
Indicates the total
Loss Of Signal
(LOS) duration
NO NO Yes None
within the
measurement
periods.
Indicates the total
length of
NO NO Yes None
measurement
periods.
Indicates the total
number of received
packets within the NO NO Yes None
measurement
periods.
Indicates the
number of the BITS YES NO No None
clock link.
Indicates the
number of the
cabinet where the NO NO No None
BITS clock link is
configured.
Indicates the
number of the
subrack where the NO NO No None
BITS clock link is
configured.
Indicates the
number of the slot
where the BITS NO NO No None
clock link is
configured.
Indicates the
activation status of
the BITS clock link.
If the link is active,
NO NO Yes None
the BITS clock link
is the current clock
source of the
system.
Indicates the
availability of a
BITS clock link.
Only an available
clock link can serve
as the current clock NO NO Yes None
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates the
priority of the clock
source. The value 1
indicates that the
current clock source
has the highest NO NO No None
priority, and the
value 4 indicates
that the current
clock source has
the lowest priority.
Indicates the
number of the
YES NO No None
E1/T1 line clock
link.
Indicates the
number of the
E1/T1 line clock link
is configured.
Indicates the
number of the
E1/T1 line clock link
is configured.
Indicates the
number of the slot
where the E1/T1 NO NO No None
line clock link is
configured.
Indicates the
number of the port
where the E1/T1 NO NO No None
line clock link is
configured.
Indicates the
the E1/T1 line clock
link. If the link is
NO NO Yes None
active, the E1/T1
line clock link is the
of the system.
Indicates the
availability of the
E1/T1 line clock
link. Only an
available clock link
can serve as the
NO NO Yes None
current clock
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates the
source. The value 1
indicates that the
priority, and the
value 4 indicates
that the current
clock source has
Indicates the
number of the peer YES NO No None
reference clock link.
Indicates the
standard of the
peer reference
clock. The standard
of the peer NO NO No None
reference clock is
another standard in
the same BBU
subrack by default.
Indicates the
the peer reference
clock link. If the link
is active, the peer NO NO Yes None
reference clock link
source of the
system.
Indicates the
availability of the
peer reference
clock link. Only an
can serve as the
NO NO Yes None
current clock
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates the
number of a TOD
clock link. The
number of the TOD
clock link must
correspond to the
number of the TOD
port on the USCUb YES NO No None
or UMPT. For
example, clock link
No.0 corresponds
to port No.0, clock
link No.1
corresponds to port
No.1.
Indicates the type
of a TOD clock link.
It indicates whether
the corresponding
TOD port is an input
or output port. An
input port is used to
input clock signals
NO NO No None
to the BS, and an
output port is used
to provide clock
signals for other
BSs. Only the TOD
clock of input type
can serve as a
clock source.
Indicates the
number of the
TOD clock link is
configured.
Indicates the
number of the
TOD clock link is
configured.
Indicates the
number of the slot
where the TOD NO NO No None
clock link is
configured.
Indicates the type
of TOD feeder,
which can only be NO NO No None
the twisted-pair
cable currently.

of the TOD feeder.
The feeder delay is
calculated on the
basis of the TOD
feeder length to
ensure the clock
accuracy. The clock
accuracy is affected NO NO No None
if there is an
excessively large
difference (about 20
m) between the
value of this
parameter and the
actual feeder
length.
Indicates the
a TOD clock link. If
the link is active,
NO NO Yes None
the TOD clock link
source of the
system.
Indicates the
availability of an
TOD clock link.
Only an available
as the current clock NO NO Yes None
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates the feeder
delay of the TOD
clock link. If the
feeder delay is not
NO NO Yes None
supported by the
satellite card, this
parameter is set to
NULL.
Indicates the
source. The value 1
indicates that the
priority, and the
value 4 indicates
that the current
clock source has
Indicates the
number of the GPS YES NO No None
clock link.
Indicates the
cabinet number of
the board where the NO NO No None
satellite card is
attached.
Indicates the
subrack number of
the board where the NO NO No TDLOFD-009001
satellite card is
attached.
Indicates the slot
number of the
board where the NO NO No None
satellite card is
attached.
Indicates the mode

to obtain the
NO NO No None
position of the GPS
satellite.
Indicates the
longitude of the
GPS antenna. A
negative value
indicates the west NO NO No None
longitude, and a
positive value
indicates the east
longitude.
Indicates the
latitude of the GPS
antenna. A negative
value indicates the
NO NO No None
south latitude, and
a positive value
indicates the north
latitude.
Indicates the
altitude of the GPS
antenna. A negative
value indicates that
the GPS antenna is
NO NO No None
below the sea level,
and a positive value
indicates that the
GPS antenna is
above the sea level.
Indicates the
antenna angle,
which is the angle NO NO No None
with the horizontal
line.
Indicates the feeder

delay of the GPS
clock link. If the
feeder delay is not
NO NO Yes None
supported by the
satellite card, this
parameter is set to
NULL.
Indicates the
duration for tracing
NO NO No None
the position of the
GPS satellite.
Indicates the
precision
requirement for NO NO No None
tracing the position
of the GPS satellite.
Indicates the type
of the GPS feeder,
which can be the
twisted-pair cable or
coaxial cable. The
board-mounted NO NO No None
GPS antenna uses
the coaxial cable.
The RGPS antenna
uses the twisted-
pair cable.

of the GPS feeder.
The actual feeder
length is the one
between the GPS
antenna and the
board connected to
the GPS antenna.
Based on the
feeder length, the
feeder delay is NO NO No None
calculated to
ensure the clock
accuracy. The clock
accuracy is affected
if the error between
the value of this
parameter and the
actual feeder length
is greater than 20
m.
Indicates the
software version of
NO NO Yes None
the satellite
receiver.
Indicates whether
the position of the
GPS satellite is NO NO Yes None
locked by the GPS
reference receiver.
Indicates whether
the calendar
information of the NO NO Yes None
GPS reference
receiver is valid.
Indicates whether
the GPS satellite
positioned by the NO NO Yes None
GPS reference
receiver is valid.
Indicates whether
the position of the
GPS satellite is set NO NO Yes None
on the GPS
reference receiver.
Indicates the clock
adjusting state of
NO NO Yes None
the GPS reference
receiver.
Indicates whether
the clock mode of
NO NO Yes None
the GPS reference
receiver is valid.
Indicates the
number of locked
NO NO Yes None
GLONASS
satellites.
Indicates the
physical status of
the satellite card,
which can be
NOTEXIST
(Inexistent),
ANTENNASHORTE
D (Antenna
Shorted),
ANTENNAOPENE
D (Antenna
Opened),
SELF_CHECK_FAI
LURE (Self-check
NO NO Yes None
Failure),
COMEXCEPTION
(COM Port
Communication
Fault), NORMAL
(Normal),
UNKNOWN
(Unknown
Exception),
USCUINVALID
(USCU Invalid), or
UNKNOWN_STAR
_CARD (Unknown
Star Card).
Indicates the
physical type of the
satellite card, which
can be M12M, UT,
RT, K161, GG16,
JNS100, RGPS,
NO NO Yes None
CWAIN, RTSMT,
UBLOX5, BD7702,
NAVIOR, PPSTOD,
M1000, TRGPS,
BD7702CMS, or
OEM4.
Indicates the
number of locked NO NO Yes None
GPS satellites.
COMPASS,
GPS/GLONASS,
COMPASS/GPS
with COMPASS
prioritized, and
GPS/COMPASS
with GPS
prioritized. Satellite
cards are classified
into dual-mode
satellite cards and
single-mode
satellite cards. A
dual-mode satellite
card supports two
satellite searching
modes. For
example, the
working mode of a
NO NO No None
COMPASS/GPS
satellite card can be
COMPASS
prioritized or GPS
prioritized. In
COMPASS
prioritized mode,
the satellite card
processes signals
from COMPASS
satellites only. In
GPS prioritized
mode, the satellite
card processes
signals from GPS
satellites only. A
single-mode
satellite card
supports only one
Indicates the
number of locked
NO NO Yes None
COMPASS
satellites.
Indicates the
the GPS clock link.
NO NO Yes None
the GPS clock link
source of the
system.
Indicates the
source. The value 1
indicates the
priority, and the
value 4 indicates
the current clock
source has the
lowest priority.
Indicates the
number of the IP YES NO No None
clock link.
Indicates the type

of the IP clock
protocol, which can
be PTP or Huawei
proprietary protocol.
PTP includes
IEEE1588 V2 and
G.8265.1.
IEEE1588 V2,
defined by the
IEEE, supports both
time
synchronization and
frequency
LOFD-00301302 /
synchronization.
NO NO No TDLOFD-00301302
G.8265.1 supports
LOFD-00301303
frequency
synchronization
only. Huawei
proprietary protocol,
which is the
Huawei-defined IP
clock protocol,
applies to the
interconnection
between Huawei
equipment and
supports frequency
synchronization
only.
Indicates the
number of the
IP clock link is
configured.
Indicates the
number of the
IP clock link is
configured.
Indicates the
number of the slot
NO NO No None
where the IP clock
link is configured.
Indicates the client LOFD-00301302 /

IPv4 address of the NO NO No TDLOFD-00301302
IP clock link. LOFD-00301303
Indicates the server LOFD-00301302 /
Indicates the
domain to which the
IP clock link
belongs. The
LOFD-00301302 /
setting of this NO NO No
TDLOFD-00301302
parameter must be
the same as the
setting of the clock
server.
set to P2P. There
are two application
modes for
IEEE1588 V2: the
Point-to-Point mode
(P2P) and End-to-
End mode (E2E).
The Point-to-Point
mode, also known
as the full-
supported mode,
involves all clock
nodes: the OC, BC,
and TC. This mode
requires that the
Boundary clock or
Transparent clock
should be
supported by all NO NO No None
network devices
between the Time
Server and Time
Client. The delay
variation of time
stamp is
compensated by
the Boundary clock
or Transparent
clock, so the
frequency and time
of the BS can be
easily recovered. In
End-to-End mode,
the time stamp is
transmitted from the
Time Server to BS
by means of
Indicates whether
the BMC (Best
Master Clock)
algorithm is
enabled or not. ON
indicates that the NO NO No None
BMC algorithm is
enabled, and OFF
indicates that the
BMC algorithm is
disabled.
Indicates the
priority configured
by the user for the
BMC (Best Master
Clock) algorithm.
The information
about the priority
can be collected
from the Time
Server. This
parameter specifies
the clock quality NO NO No None
that is anticipated
by the user. The
Time Server with
the matching clock
quality is selected
as the target server.
Class0 has the
highest priority, and
Class0 to Class3
indicate priorities in
descending order.
Indicates the
priority configured
by the user for the
BMC (Best Master
Clock) algorithm.
The information
about the priority
can be collected
from the Time
Server. This
parameter specifies
that is anticipated
by the user. The
Time Server with
the matching clock
quality is selected
Class0 has the
Class0 to Class3
descending order.
Indicates the
priority configured
by the user for the
BMC (Best Master
Clock) algorithm.
The information
about the priority
can be collected
from the Time
Server. This
parameter specifies
that is anticipated
by the user. The
Time Server with
the matching clock
quality is selected
Class0 has the
Class0 to Class3
descending order.
Indicates the
priority configured
by the user for the
BMC (Best Master
Clock) algorithm.
The information
about the priority
can be collected
from the Time
Server. This
parameter specifies
that is anticipated
by the user. The
Time Server with
the matching clock
quality is selected
Class0 has the
Class0 to Class3
descending order.
Indicates the
current priority class NO NO Yes None
of the IP clock link.
Indicates whether
the clock source is NO NO No None
specified.
Indicates the MAC

address of the clock
source for the IP
clock server. The
NO NO No None
MAC address must
be in the format of
XXXX-XXXX-
XXXX.
Indicates the
the IP clock link. If
the IP clock link is NO NO Yes None
active, it is the
of the system.
Indicates the
availability of the IP
clock link. Only an
can serve as the
current clock NO NO Yes None
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates the
LOFD-00301302 /
networking type for NO NO No
TDLOFD-00301302
the IP clock.
Indicates the
compensation for LOFD-00301302 /
NO NO No
asymmetry of IP TDLOFD-00301302
clock links.
Indicates the step

mode, which can be
NO NO Yes None
ONE_STEP or
TWO_STEP.
Indicates the self-
acquired VLAN ID
NO NO Yes None
of the IP clock
server.
Indicates the offset
of the Universal
NO NO Yes None
Time Coordinated
(UTC).
Indicates the
source. The value 1
indicates that the
priority, and the
value 4 indicates
that the current
clock source has
Indicates the
frequency at which
the clock source
sends
NO NO No None
announcement
packets based on
its negotiation with
the BS.
Indicates the
frequency at which
the clock source
sends
NO NO No None
synchronization
packets based on
its negotiation with
the BS.
Indicates the
priority of the IP
clock server. The
value 0 indicate the
the value 255
indicates the lowest
priority.If two IP
clock servers are
required, the value
of this parameter is
NO NO No None
used to identify the
active and standby
IP clock servers.
The IP clock server
with a higher priority
serves as the active
server and the IP
clock server with a
lower priority serves
as the standby
server.
Indicates the type
of protocol
supported by the
IEEE 1588 V2-
compliant IP clock
link, which can be
ITU-T G.8265.1 or
IEEE 1588 V2. ITU-
T G.8265.1 is
defined by the
International
Telecommunication
Union (ITU) for
frequency
synchronization of
an IEEE 1588 V2-
compliant IP clock
NO NO No None
link with the
networking type of
UNICAST. An IP
clock link in
compliant with ITU-
T G.8265.1
supports
interconnection with
servers from other
vendors. An IP
clock link in
compliant with IEEE
1588 V2 does not
support
interconnection with
servers from other
vendors.
Indicates the
interval at which
negotiations are
performed between
the BS and IP clock
NO NO No None
server. After the
interval elapses, the
BS initiates another
negotiation with the
IP clock server.
Indicates the mode

NO NO No None
of the IP address.
Indicates the client
IPv6 address of the NO NO No None
IP clock link.
Indicates the server LOFD-00301302 /

Indicates the
number of the
synchronous-
Ethernet clock link. YES NO No None
Currently, only one
link (link No.0) can
be configured.
Indicates the
number of the
cabinet where the
NO NO No None
synchronous-
Ethernet clock link
is configured.
Indicates the
number of the
subrack where the
NO NO No None
synchronous-
Ethernet clock link
is configured.
Indicates the
number of the slot
where the
NO NO No None
synchronous-
Ethernet clock link
is configured.
Indicates the
number of the port
where the
NO NO No None
synchronous-
Ethernet clock link
is configured.
Indicates whether
handling of SSM
frames is
supported.
SSM:
NO NO No None
Synchronization
Status Message.
Recommendation
ITU-T
G.8264/Y.1364.
Indicates the
a synchronous-
Ethernet clock link.
NO NO Yes LOFD-00301301
the synchronous-
Ethernet clock link
source of the
system.
Indicates the
availability of a
synchronous-
Ethernet clock link.
Only an available
NO NO Yes LOFD-00301301
as the current clock
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates the
source. The value 1
indicates that the
priority, and the
value 4 indicates
that the current
clock source has
Indicates the
availability of the
clock source. Only
an available clock
link can serve as
the current clock NO NO Yes None
source. Otherwise,
the clock link
cannot be locked
even if it is
activated.
Indicates whether a
clock source is
licensed to be used.
Only a licensed NO NO Yes None
clock source can
serve as the current
clock source.
Indicates the
source. The value 1
indicates that the
has the highest NO NO Yes None
priority, and the
value 4 indicates
that the current
clock source has
Indicates the clock

link number of the
reference clock
source. When the
Selected Clock
Source parameter
is set to
GPS+SYNCETH,
this parameter
indicates the
number of the GPS
clock link. When the
Selected Clock
Source parameter
is set to
SYNCETH+IPCLK,
this parameter NO NO No None
indicates the
number of the IP
clock link. When
this parameter is
set to AUTO, the
system selects an
from those of the
specified reference
clock source. If
there is more than
one clock link and
the selected clock
link fails, another
will be used.
Indicates the type
of the user-selected NO NO No None
clock source.
Indicates the
working mode of
the system clock.
Manual indicates
that a clock source
must be specified
by the user. Auto
indicates that the
system
automatically
selects a clock
LBFD-00300501 /
source based on NO NO No
TDLBFD-00300501
the priority and
availability of the
clock source. Free
indicates that the
system clock works
in free-running
mode, that is, the
system clock does
not trace any
reference clock
source.
Indicates the clock

synchronization
mode of a BS,
which can be
NO NO No None
frequency
synchronization or
time
synchronization.
Indicates the status
of the current clock
source, which can
be Normal, Lost,
Unavailable, Jitter,
NO NO Yes None
Frequency
Deviation,
Phaseoutscope, or
Inconsistent Clock
References.
Indicates the
working mode of
the clock. It also
indicates whether
the system clock is
stable. The working NO NO Yes None
mode of the clock
can be Fast
tracking, Locked,
Holdover, or Free
running.
Indicates the clock

NO NO Yes None
source in use.
Indicates the
number of the
cabinet where the NO NO Yes None
system clock is
located.
Indicates the
number of the
subrack where the NO NO Yes None
system clock is
located.
Indicates the
number of the slot
NO NO Yes None
where the system
clock is located.
Indicates the clock
quality level of the
BS. The values for
this parameter are
listed in quality
descending order. NO NO No None
QL-PRC indicates
the highest quality
level and QL-DNU
quality level.
Indicates the
cabinet number of
YES NO No None
the baseband
processing board.
Indicates the
subrack number of
YES NO No None
the baseband
processing board.
Indicates the slot

number of the
YES YES No None
baseband
processing board.
Indicates the type

NO NO No None
of the board.
TDD_ENHANCE
indicates the TDD
mode integrated
with the
BeamForming (BF)
function. When
RRUs working in
LTE TDD 4T4R
mode are used, it is
recommended that
the baseband
processing board
work in TDD BF
mode. The BF
function provides
the data
transmission
service in
transmission modes
NO NO No None
7 and 8, as defined
in 3GPP TS 36.213.
When RRUs
working in TD-LTE
8T8R single mode
are used, it is
recommended that
the baseband
processing board
work in TDD_8T8R
mode. In addition,
the baseband
processing board
supports the BF
function and CPRI
specifications are
applied between
the BBU and the
RRU. In TDD_TL
Indicates the
administrative state
of the board. The
of the board can be NO NO No None
blocked, unblocked,
or shutting down.
For details, see
ITU-T X.731.
Indicates the
scheduled duration
NO NO No None
before a board is
blocked.
Indicates the block
type of the board.
IMMEDIATE
(Immediate):
indicates that the
board is blocked
and services carried
by the board are
interrupted
immediately after NO NO No None
the command is
executed. DELAY
(Delay): indicates
that the board is
blocked and
services carried by
the board are
interrupted after a
scheduled duration.
Indicates the alarm

status of the board.
The alarm state of
the board can be
normal, warning,
NO NO Yes None
minor or critical. For
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
operational state of
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
status of the board,
which can be
Uninstalled,
Starting up, Normal,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
lost, In test, or the
combination of
various states. For NO NO Yes None
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
label, a text file with
a maximum of 2
KB. It is used to
record the
manufacturing NO NO Yes None
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
code of the board NO NO Yes None
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
number of the NO NO Yes None
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
Indicates the object
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
temperature of a NO NO Yes None
board.
Indicates the
temperature of the NO NO Yes None
power amplifier.
Indicates the result
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
consist of uplink NO NO Yes None
and downlink
services. The
service types of the
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.
Indicates the Office

NO NO Yes None
name of the BS.
Indicates the
software version of NO NO Yes None
the board.
Indicates the
hardware version of NO NO Yes None
the board.
Indicates the
BootROM version NO NO Yes None
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
Channel Number: NO NO Yes None
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
cabinet where the YES NO No None
BBU FAN unit is
located.
Indicates the
number of the
subrack where the YES NO No None
BBU FAN unit is
located.
Indicates the
number of the slot
YES YES No None
where the BBU FAN
unit is located.
Indicates the
current temperature
NO NO Yes None
of the BBU FAN
unit.
Indicates the
rotation speed of a
fan in the BBU,
which is the ratio of
NO NO Yes None
the current rotation
speed of the fan to
its maximum
rotation speed.
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
cabinet number of YES YES No None
the CCU.
Indicates the
subrack number of YES NO No None
the CCU.
Indicates the slot

YES NO No None
number of the CCU.
Indicates the
cabinet number of
NO NO No None
the manager unit of
the CCU.
Indicates the
subrack number of
NO NO No None
the manager unit of
the CCU.
Indicates the
number of the serial
NO NO No None
port to which the
CCU is connected.
Indicates whether
the CCU is directly
connected to its NO NO No None
manager unit,
which is a BBU.
Indicates the
position of the CCU NO YES No None
on a CCU chain.
Indicates the
working standard of
the manager unit to NO NO No None
which the CCU is
connected.
Indicates whether
to allow the report
of a dedicated
Boolean alarm. If
the shield flag for a NO NO No None
Boolean alarm is
enabled, the
Boolean alarm
cannot be reported.
Indicates the
connecting status of
NO NO Yes None
the port on the left
of the CCU.
Indicates the
connecting status of
NO NO Yes None
the port on the right
of the CCU.
Indicates the
the CCU.
Indicates the PCB
NO NO Yes None
version of the CCU.
Indicates the
erasable
programmable logic NO NO Yes None
device (EPLD)
version of the CCU.
Indicates the ID of
YES NO No None
the RRU chain/ring.
Indicates the
current Common
Public Radio
Interface (CPRI) NO NO Yes None
line rate at the head
of the RRU
chain/ring.
NOTREADY(Not
ready),
NEGOTIATING(Ne
gotiating),
NEGOTIATED(Neg
otiated),
TIMEOUT(Timeout)
, or
USERCONFIG(US
ERCONFIG). The
value
NOTREADY(Not
ready) indicates
that the rate
negotiation has not
been started. The
value
NEGOTIATING(Ne
gotiating) indicates
NO NO Yes None
that the rate is
being negotiated.
The value
NEGOTIATED(Neg
otiated) indicates
that the rate
negotiation is
complete. The
value
TIMEOUT(Timeout)
indicates that the
rate negotiation
timed out due to a
software or
hardware fault
during the
negotiation. The
value
USERCONFIG(US
Indicates the
current Common
Public Radio
Interface (CPRI) NO NO Yes None
line rate at the tail
of the RRU
chain/ring.
ready),
NEGOTIATING(Ne
gotiating),
NEGOTIATED(Neg
otiated),
TIMEOUT(Timeout)
, or
USERCONFIG(US
ERCONFIG). The
value
NOTREADY(Not
ready) indicates
that the rate
negotiation has not
been started. The
value
NEGOTIATING(Ne
gotiating) indicates
that the rate is
NO NO Yes None
being negotiated.
The value
NEGOTIATED(Neg
otiated) indicates
that the rate
negotiation is
complete. The
value
TIMEOUT(Timeout)
indicates that the
rate negotiation
timed out due to a
software or
hardware fault
during the
negotiation. The
value
USERCONFIG(US
ERCONFIG)
Indicates the
NO NO Yes None
cabinet number.
Indicates the
NO NO Yes None
subrack number.
Indicates the slot
NO NO Yes None
number.
Indicates the
number of an RRU
carried on the RRU
chain/ring. The
RRUs are
numbered from 0 in
ascending order. If
the RRU chain is
NO NO Yes None
connected to the
ports located on the
baseband
processing boards,
the first port is the
head of the chain,
and the last port is
the tail of the chain.
Indicates the
maximum bit rate at
the Common Public
Radio Interface
(CPRI) port. If the
maximum bit rate is
NULL, the RF
NO NO Yes None
module or
baseband interface
board does not
support the rate
negotiation, or the
rate negotiation
fails.
Indicates the
cabinet number of
the board where the
CPRI port is
located. This
parameter is
configured
automatically when
the CPRI port is
created. A CPRI
YES NO No None
port is created
automatically when
a BBP is added by
running the ADD
BRD command.
The CPRI port is
used for the
configuration check
when an RRU
chain/ring is added.
Indicates the
subrack number of
the board where the
CPRI port is
located. This
parameter is
configured
automatically when
the CPRI port is
created. A CPRI
YES NO No None
port is created
automatically when
a BBP is added by
running the ADD
BRD command.
The CPRI port is
used for the
configuration check
when an RRU
Indicates the slot
number of the
board where the
CPRI port is
located. This
parameter is
configured
automatically when
the CPRI port is
created. A CPRI
YES YES No None
port is created
automatically when
a BBP is added by
running the ADD
BRD command.
The CPRI port is
used for the
configuration check
when an RRU
Indicates the optical

port number of the
board where the
CPRI port is
located. This
parameter is
configured
automatically when
the CPRI port is
created. A CPRI
YES YES No None
port is created
automatically when
a BBP is added by
running the ADD
BRD command.
The CPRI port is
used for the
configuration check
when an RRU
Indicates the rate at
NO NO Yes None
the CPRI port.
Indicates the
of the CPRI port.
When the CPRI
port is locked, it
indicates that a
breakpoint is
configured on the
RRU chain/ring. At
this moment,
although the optical
cables are
connected, the
NO NO Yes None
CPRI link is
disconnected. The
breakpoint is
configured to
prevent temporary
alarms from being
reported during
network operations.
When the CPRI
port is unlocked, it
indicates that there
is no breakpoint on
the RRU chain/ring.
Indicates the in-

position state of the NO NO Yes None
CPRI port.
Indicates the mode
of the CPRI port.
There are two
modes: Maser and
Slave. All CPRI
ports on a
baseband
processing board
work in master
mode. On the first-
level RRU in an
RRU chain, the
CPRI port
connected to a
baseband
processing board NO NO Yes None
works in slave
mode and the other
CPRI port
connected to the
second-level RRU
works in master
mode. When an
RRU and the
baseband
processing boards
are in dual-star
topology, the two
CPRI ports on the
RRU work in slave
mode.
Indicates the type

NO NO Yes None
of the CPRI port.
Indicates the
backup mode of the NO NO Yes None
CPRI port.
Indicates the
channel type of the NO NO Yes None
CPRI port.
Indicates the DL
bandwidth of the NO NO Yes None
CPRI port.
Indicates the
number of downlink
NO NO Yes None
connections of the
CPRI port.
Indicates the
number of uplink
NO NO Yes None
connections of the
CPRI port.
Indicates the Mux

Status of the CPRI NO NO Yes None
port.
Indicates the power

consumption
NO NO No None
measurement point
of the BS.
Indicates the
cabinet number of
the main control YES NO No None
and transmission
board.
Indicates the
subrack number of
the main control YES NO No None
and transmission
board.
Indicates the slot
number of the main
YES YES No None
control and
transmission board.
Indicates the type
NO YES No None
of the board.
Indicates the active

or standby status of
the main control
and transmission
board. The active or
standby status is
NO NO Yes None
available only to the
main control and
transmission board.
This parameter for
other types of board
is set to NULL.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
PEU is located.
Indicates the
number of the
YES NO No None
subrack where the
PEU is located.
Indicates the
number of the slot
YES YES No None
where the PEU is
located.
Indicates the spare
NO NO Yes None
power of the UPEU.
Indicates the spare
NO NO Yes None
power of the BBU.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates whether
the PSU intelligent
shutdown switch in NO NO No None
a BS is enabled or
disabled.
Indicates the
cabinet number of
YES YES No None
the optical or
electrical module.
Indicates the
subrack number of
YES YES No None
the optical or
electrical module.
Indicates the slot
number of the
YES YES No None
optical or electrical
module.
Indicates the
number of the
module. If a UCIU is
queried, values 0 to
4 indicate the ports
M0 to M4 on the
board panel, and
value 8 indicates
the port S0 on the
YES YES No None
board panel. If a
UMPT is queried,
value 8 indicates
the port CI on the
board panel. If a
LBBPd board is
queried, value 6
indicates the port
HEI on the board
panel.
Indicates whether
the optical or
NO NO Yes None
electrical module is
in position.
Indicates the type
of the optical or
electrical module,
which can be SFP,
enhanced SFP, or
electrical port.
These three types
are different in the
supported
transmission rates
and transmission
distance. The
transmission
distance of the
electrical port is
short, so it is used
NO NO Yes None
to connect the BBU
or RFU. The Small
Form-factor
Pluggable (SFP) is
a small hot-
swappable module,
which can be
connected to an
optical module or
an electrical
module. The
difference between
the enhanced SFP
and SFP is the
supported
transmission rates.
Indicates the
manufacturer of the
NO NO Yes None
module.
Indicates the
transmission mode
of the optical
NO NO Yes None
module, that is,
single-mode or
multi-mode.
Indicates the
wavelength of the NO NO Yes None
optical module.
Indicates the
transmission code
NO NO Yes None
rate of the optical or
electrical module.
Indicates the
maximum distance
that signals from
the optical module
can travel along a
single-mode optical
fiber with a 9- NO NO Yes None
micrometer core
diameter. The value
0 indicates that the
optical module does
not support this
type of optical fiber.
Indicates the
maximum distance
that signals from
the optical module
can travel along a
single-mode optical
micrometer core
diameter. The value
optical module does
not support this
Indicates the
maximum distance
that signals from
the optical module
can travel along a
multi-mode optical
micrometer core
diameter. The value
optical module does
not support this
Indicates the
maximum distance
that signals from
the optical module
can travel along a
multi-mode optical
fiber with a 62.5- NO NO Yes None
micrometer core
diameter. The value
optical module does
not support this
Indicates the
observed
temperature of the
optical module. This
NO NO Yes None
parameter is valid
only when the
optical module type
is ESFP.
Indicates the
observed voltage of
the optical module.
This parameter is NO NO Yes None
valid only when the
optical module type
is ESFP.
Indicates the
observed current of
the optical module.
This parameter is NO NO Yes None
valid only when the
optical module type
is ESFP.
Indicates the TX
optical power of the
parameter is valid NO NO Yes None
only when the
optical module type
is ESFP.
Indicates the RX
optical power of the
parameter is valid NO NO Yes None
only when the
optical module type
is ESFP.
Indicates the
transmission
NO NO Yes None
distance of the
electrical module.
Indicates the
cabinet number of
YES NO No None
the extension
transmission board.
Indicates the
subrack number of
YES NO No None
the extension
transmission board.
Indicates the slot
number of the
YES YES No None
extension
transmission board.
Indicates the type
NO YES No None
of the sub-board.

or standby status of
the extended NO NO Yes None
transmission
processing board.
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
Indicates the
670.1 Band7:
the UCIU.
Indicates the
subrack number of YES YES No None
the UCIU.
Indicates the slot
UCIU.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
UEIU is located.
Indicates the
number of the
YES NO No None
subrack where the
UEIU is located.
Indicates the
number of the slot
YES YES No None
where the UEIU is
located.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
USCU is located.
Indicates the
number of the
YES NO No None
subrack where the
USCU is located.
Indicates the
number of the slot
YES YES No None
where the USCU is
located.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
deployment ID. The
parameter value
can contain digits,
letters, left
parenthesis ((), right NO NO No None
parenthesis ()),
underlines (_), dots
(.), ampersands (&),
is less than (<), and
is greater than (>).
Indicates the
battery intelligent
management switch
status. Intelligent
battery power
NO NO No None
management
prolongs the
lifespan of a battery
using the floating
charge mode.
Whether to allow
the generation of
the Power Lose
Redundancy alarm.
The PSUs need to
be configured in
N+1 backup mode.
When this NO NO No None
parameter is set to
"YES", the BTS
reports the Power
Lose Redundancy
alarm if the PSUs
are not configured
in N+1 mode.
Indicates the
special alarm status
of the NE. The
status is set to NO NO No None
TESTING by
default by the
manufacturers.
Indicates the start

time of special
alarm status of the
NE. If the start time
NO NO No None
is not specified, the
special alarm status
takes effect
immediately.
Indicates the end
time of special
NO NO No None
alarm status of the
NE.
Indicates the
remarks of special
NO YES No None
alarm status of the
NE.
Indicates the
current
maintenance mode NO NO Yes None
of the network
element (NE).
Indicates the direct

voltage alarm
switch. The switch
controls whether to
report the ALM- NO NO No None
26113 Base Station
DC Power Supply
Abnormal in the
case of low voltage.
Indicates the DC
voltage alarm
occured threshold.
When the load
voltage is lower
than the DC voltage
alarm occured
threshold and the NO NO No None
direct voltage alarm
switch is set to
ENABLE, an ALM-
26113 Base Station
DC Power Supply
Abnormal is
reported.
Indicates the DC
voltage alarm
restored threshold.
When the load
voltage is higher
than the DC voltage
alarm restored
threshold and the NO NO No None
direct voltage alarm
switch is set to
ENABLE, an ALM-
26113 Base Station
DC Power Supply
Abnormal is
cleared.
Indicates the
YES YES No None
cabinet number.
Type of a cabinet.
This parameter is
set to VIRTUAL
when the type of a NO NO No None
cabinet is not within
the value range of
this parameter.
Indicates a brief
description of the
cabinet, which can
be the function, NO NO No None
location, and some
other information of
the cabinet.
Indicates the
NO NO Yes None
cabinet type.
Indicates the
the subrack.
Indicates the
subrack.
Indicates the type
NO YES No None
of the subrack.
Indicates a brief
description of the
subrack, which can
be the function, NO NO No None
location, and some
other information of
the subrack.
Indicates the type

of power supply to NO NO Yes None
the subrack.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar

or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
EMU is located.
Indicates the
number of the
YES NO No None
subrack where the
EMU is located.
Indicates the
number of the slot
YES NO No None
where the EMU is
located.
Indicates the
cabinet number of
the manager that
LBFD-004012 /
manages the EMU. NO NO No
TDLBFD-004012
The manager of the
EMU is usually a
BBU or RRU.
Indicates the
subrack number of
the manager. The LBFD-004012 /
NO NO No
manager of the TDLBFD-004012
EMU is usually a
BBU or RRU.
Indicates the
number of the serial LBFD-004012 /
NO YES No
port to which the TDLBFD-004012
EMU is connected.
Indicates the
communication
address of the
EMU, which is
determined by the
settings of the 4-bit
dual in-line package
(DIP) switch on the
EMU. The
communication
address is used by
the EMU to
communicate with
the main control
and transmission
board. The value of
this parameter must LBFD-004012 /
NO NO No
be consistent with TDLBFD-004012
the actual settings
of the DIP switch.
The 4-bit DIP switch
can be treated as a
4-bit binary number.
The settings of ON
and OFF are
represented by 1
and 0 respectively.
Convert the 4-bit
number from binary
to decimal, and
then the decimal
number is used as
the value of this
parameter.
Indicates the lower

limit of temperature.
When the
temperature is
LBFD-004012 /
below the lower NO NO No
TDLBFD-004012
limit, an ALM-25650
Temperature
Abnormal alarm is
reported.
Indicates the upper

When the
temperature
LBFD-004012 /
exceeds the upper NO NO No
TDLBFD-004012
limit, an ALM-25650
Temperature
Abnormal alarm is
reported.
Indicates the lower
limit of humidity.
When the humidity
LBFD-004012 /
is below the lower NO NO No
TDLBFD-004012
limit, an ALM-25651
Humidity Abnormal
alarm is reported.
Indicates the upper

limit of humidity.
When the humidity
LBFD-004012 /
exceeds the upper NO NO No
TDLBFD-004012
limit, an ALM-25651
Humidity Abnormal
alarm is reported.
Indicates whether
to allow the report
of a dedicated
analog alarm. If the
LBFD-004012 /
shield flag for an NO NO No
TDLBFD-004012
analog alarm is
enabled, the analog
alarm cannot be
reported.
Indicates whether
to allow the report
of a dedicated
Boolean alarm. If
LBFD-004012 /
the shield flag for a NO NO No
TDLBFD-004012
Boolean alarm is
enabled, the
Boolean alarm
cannot be reported.
Indicates the
LBFD-004012 /
current temperature NO NO Yes
TDLBFD-004012
of the environment.
Indicates the LBFD-004012 /
NO NO Yes
ambient humidity. TDLBFD-004012
Indicates the -48 V
input voltage from LBFD-004012 /
NO NO Yes
the power supply TDLBFD-004012
cabinet.
Indicates the
current value
measured by the
NO NO Yes None
external sensor that
is connected to
analog port 1.
Indicates the
current value
measured by the
NO NO Yes None
is connected to
analog port 2.
Indicates the
current value
measured by the
NO NO Yes None
is connected to
analog port 3.
Indicates the
current value
measured by the
NO NO Yes None
is connected to
analog port 4.
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
FMU is located.
Indicates the
number of the
YES NO No None
subrack where the
FMU is located.
Indicates the
number of the slot
YES NO No None
where the FMU is
located.
Indicates the
cabinet number of
NO NO No
FMU is usually a
BBU or RRU.
Indicates the
subrack number of
NO NO No
FMU is usually a
BBU or RRU.
Indicates the
NO YES No
port where the FMU TDLBFD-004012
is connected.
Indicates the
communication
address of the
FMU. The FMU
communicates with LBFD-004012 /
NO NO No
the main control TDLBFD-004012
and transmission
board by using this
communication
address.
Indicates whether
to allow the report
of a dedicated
Boolean alarm. If
Boolean alarm is
enabled, the
Boolean alarm
cannot be reported.
Indicates the ratio
of the current
rotation speed of LBFD-004012 /
NO NO Yes
the fan to its TDLBFD-004012
maximum rotation
speed.
Indicates the
temperature at the LBFD-004012 /
NO NO Yes
air outlet of the TDLBFD-004012
FMU.
Indicates the
LBFD-004012 /
temperature at the NO NO Yes
TDLBFD-004012
air inlet of the FMU.
Indicates the
average rotation LBFD-004012 /
NO NO Yes
speed of the fan per TDLBFD-004012
minute.

of smart
temperature
control. When the
smart temperature
control is enabled,
the rotation speed
of the fan is
adjusted by the
FMU according to
the temperature
NO NO No None
control parameters
delivered by the
BBU. When the
smart temperature
control is disabled,
the rotation speed
of the fan is
adjusted by the
FMU automatically
according to the
temperature.
Indicates the mode
that the fan speed
adjustment adopts.
Mode 0 is the
default mode, which
achieves balance in
system power
consumption, noise,
and temperature
control. It applies
to most scenarios.
Mode 9 is the
synchronization
mode, which brings
NO NO No None
low noise but poor
temperature
control.
Inappropriate use of
mode 9 may lead to
serious results such
as service
interruption on the
RF module due to
overtemperature.
You need to contact
Huawei technical
support before
adopting this mode.
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
TCU is located.
Indicates the
number of the
YES NO No None
subrack where the
TCU is located.
Indicates the
number of the slot
YES NO No None
where the TCU is
located.
Indicates the
cabinet number of
NO NO No
TCU is usually a
BBU or RRU.
Indicates the
subrack number of
NO NO No
TCU is usually a
BBU or RRU.
Indicates the
NO YES No
port where the TCU TDLBFD-004012
is connected.
Indicates the
communication
address of the TCU.
The TCU
communicates with LBFD-004012 /
NO NO No
the main control TDLBFD-004012
and transmission
board by using this
communication
address.
Indicates the lower

threshold of the
temperature. If the
cabinet air outlet
temperature is
LBFD-004012 /
lower than the NO NO No
TDLBFD-004012
value, the ALM-
25655 Cabinet Air
Outlet Temperature
Unacceptable is
reported.
Indicates the upper

threshold of the
temperature. If the
cabinet air outlet
temperature is
LBFD-004012 /
higher than the NO NO No
TDLBFD-004012
value, the ALM-
25655 Cabinet Air
Outlet Temperature
Unacceptable is
reported.
Indicates whether
to allow the report
of a dedicated
Boolean alarm. If
Boolean alarm is
enabled, the
Boolean alarm
cannot be reported.
NO NO Yes None
type of the TCU.
Indicates the
LBFD-004012 /
temperature at the NO NO Yes
TDLBFD-004012
air inlet of the TCU.
Indicates the
temperature at the LBFD-004012 /
NO NO Yes
air outlet of the TDLBFD-004012
TCU.
Indicates the
LBFD-004012 /
temperature inside NO NO Yes
TDLBFD-004012
the TCU.
Indicates the
average rotation
speed of the inner NO NO Yes None
circulation fan per
minute.
Indicates the
average rotation
speed of the outer NO NO Yes None
circulation fan per
minute.
Indicates the
current heating
power of the TCU. If
this parameter is
displayed as 0, the
TCU is not heating
the cabinet. If this
parameter is not
displayed as 0, the NO NO Yes None
TCU is heating the
cabinet. If this
parameter is
displayed as NULL,
the TCU used for
heating does not
exist or is not
supported.
Indicates the
the TCU.
Indicates the PCB
NO NO Yes None
version of the TCU.
Indicates the
erasable
device (EPLD)
version of the TCU.
Indicates the
compiling time of
the software NO NO Yes None
program in the
TCU.
Indicates the
version description NO NO Yes None
of the TCU.
Indicates the
manufacturing date NO NO Yes None
of the TCU.
Indicates the
manufacturer of the NO NO Yes None
TCU.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
TCU is located.
Indicates the
number of the
YES NO No None
subrack where the
TCU is located.
Indicates the
number of the slot
YES NO No None
where the TCU is
located.
Indicates the
LBFD-004012 /
threshold of the low NO NO No
TDLBFD-004012
temperature state.
Indicates the
threshold of the LBFD-004012 /
NO NO No
high temperature TDLBFD-004012
state.
Indicates the
expected lowest LBFD-004012 /
NO NO No
temperature at the TDLBFD-004012
air outlet.
Indicates the
tolerable error value LBFD-004012 /
NO NO No
of temperature TDLBFD-004012
control.
Indicates the
difference between
the temperature at
LBFD-004012 /
the air inlet and that NO NO No
TDLBFD-004012
of the environment
at the normal
temperature.
Indicates the
difference between
the temperature at
LBFD-004012 /
the air outlet and NO NO No
TDLBFD-004012
that of the air inlet
at the normal
temperature.
Indicates the
difference between
the temperature at
LBFD-004012 /
the air outlet and NO NO No
TDLBFD-004012
that of the
environment at the
high temperature.
Indicates the
number of the
YES NO No None
cabinet where the
PMU is located.
Indicates the
number of the
YES NO No None
subrack where the
PMU is located.
Indicates the
number of the slot
YES NO No None
where the PMU is
located.
Indicates the
cabinet number of
NO NO No
PMU is usually a
BBU or RRU.
Indicates the
subrack number of
NO NO No
PMU is usually a
BBU or RRU.
Indicates the
NO YES No
port where the PMU TDLBFD-004012
is connected.
Indicates the
communication
address of the
PMU, which is
determined by the
settings of the 4-bit
dual in-line package
(DIP) switch on the
PMU. The
communication
address is used by
the PMU to
communicate with
the main control
and transmission
board. The value of
this parameter must LBFD-004012 /
NO NO No
be consistent with TDLBFD-004012
the actual settings
of the DIP switch.
The 4-bit DIP switch
can be treated as a
4-bit binary number.
The settings of ON
and OFF are
represented by 1
and 0 respectively.
Convert the 4-bit
number from binary
to decimal, and
then the decimal
number is used as
the value of this
parameter.
Indicates the type
of the power LBFD-004012 /
NO NO No
system for the TDLBFD-004012
PMU.
Indicates the lower

threshold of AC
input voltage. When
the AC input
LBFD-004012 /
voltage is lower NO NO No
TDLBFD-004012
than the value, an
ALM-25622 Mains
Input Abnormal
alarm is reported.
Indicates the higher

threshold of AC
input voltage. When
the AC input
LBFD-004012 /
voltage is higher NO NO No
TDLBFD-004012
than the value, an
ALM-25622 Mains
Input Abnormal
alarm is reported.
Indicates the lower
threshold of the DC
voltage. When the
output voltage of
LBFD-004012 /
the busbar is lower NO NO No
TDLBFD-004012
than the value, an
ALM-25621 DC
Output Abnormal
alarm is reported.
Indicates the upper
threshold of the DC
voltage. When the
output voltage of
LBFD-004012 /
the busbar is higher NO NO No
TDLBFD-004012
than the value, an
ALM-25621 DC
Output Abnormal
alarm is reported.
Indicates the flag
for power-off
against low voltage,
LBFD-004012 /
which determines NO NO No
TDLBFD-004012
whether the load is
powered off in the
case of low voltage.
Indicates the load
voltage below
which the load is
powered off LBFD-004012 /
NO NO No
automatically when TDLBFD-004012
load power-off
against low voltage
is enabled.
Indicates the lower

threshold of the
cabinet
temperature. If the
cabinet temperature
LBFD-004012 /
is lower than the NO NO No
TDLBFD-004012
value, an ALM-
25652 Cabinet
Temperature
Abnormal alarm is
reported.
Indicates the upper

threshold of the
cabinet
temperature. If the
cabinet temperature
LBFD-004012 /
is higher than the NO NO No
TDLBFD-004012
value, an ALM-
25652 Cabinet
Temperature
Abnormal alarm is
reported.
Indicates the lower
threshold of the
cabinet humidity. If
the cabinet humidity
is lower than the NO NO No None
value, an ALM-
25653 Cabinet
Humidity Abnormal
alarm is reported.
Indicates the upper

threshold of the
cabinet humidity. If
the cabinet humidity
is higher than the NO NO No None
value, an ALM-
25653 Cabinet
Humidity Abnormal
alarm is reported.
Indicates whether
to allow the report
of a dedicated
analog alarm. If the
LBFD-004012 /
shield flag for an NO NO No
TDLBFD-004012
analog alarm is
enabled, the analog
alarm cannot be
reported.
Indicates whether
to allow the report
of a dedicated
Boolean alarm. If
LBFD-004012 /
the shield flag for a NO NO No
TDLBFD-004012
Boolean alarm is
enabled, the
Boolean alarm
cannot be reported.
Indicates the
current AC voltage,
LBFD-004012 /
that is, the input NO NO Yes
TDLBFD-004012
mains voltage to
the rectifier.
Indicates the DC
LBFD-004012 /
output voltage of NO NO Yes
TDLBFD-004012
the busbar.
Indicates the total
load current. The
total load current is
the sum of current LBFD-004012 /
NO NO Yes
supplied by all the TDLBFD-004012
DC output terminals
on the power
subrack.
Indicates the
current cabinet LBFD-004012 /
NO NO Yes
temperature of the TDLBFD-004012
cabinet.
Indicates the
LBFD-004012 /
ambient humidity of NO NO Yes
TDLBFD-004012
the cabinet.
Indicates the
power-on status of
the secondary load.
The secondary load
can be set to
automatically
powered off in the
following modes:
HighTemperaturePo
LBFD-004012 /
werOff(High NO NO Yes
TDLBFD-004012
temperature power
off),
LowTemperaturePo
werOff(Low
temperature power
off), and
LowVoltagePowerO
ff(Low voltage
power off).
charging voltage is
relatively high. After
the battery is
discharged,
generally, the
system
automatically starts
boost-charge on the
battery. Floating
charge is used to
compensate for the
power loss of the
battery due to self-
discharge and to
keep the capacity of
the battery. It can
also recover the
battery capacity.
During the floating LBFD-004012 /
NO NO Yes
charge, the TDLBFD-004012
charging voltage is
relatively low. Force
boost charge is an
enhanced mode of
the boost charge.
The charging
current and boost
charging voltage of
the force boost
charge are higher
than those of the
boost charge, while
the charging time is
shorter than that of
the boost charge. It
can be used in the
scenario where the
electricity network is
Indicates the
charging or LBFD-004012 /
NO NO Yes
discharging current TDLBFD-004012
of batteries.
Indicates whether
the batteries that
LBFD-004012 /
are being charged NO NO Yes
TDLBFD-004012
are in the current
limiting status.
Indicates the
power-on/power-off
status of the
battery. The battery
can be
disconnected LBFD-004012 /
NO NO Yes
manually or TDLBFD-004012
disconnected
automatically for
protection purpose
based on different
situations.
Indicates the
remaining capacity
of the battery by
LBFD-004012 /
displaying the NO NO Yes
TDLBFD-004012
percentage of the
current capacity to
the total capacity.
Indicates the
LBFD-004012 /
current temperature NO NO Yes
TDLBFD-004012
of the battery.
Indicates the phase

NO NO Yes None
of the battery test.
Indicates the total

current of the
NO NO Yes None
photovoltaic array
of the PMU.
Indicates the
current of the diesel
generator which is NO NO Yes None
managed by the
PMU.
Indicates the
temperature of
auxiliary battery
NO NO Yes None
cabinet which is
connected to the
PMU.
Indicates the
the PMU.
Indicates the PCB
NO NO Yes None
version of the PMU.
Indicates the
erasable
device version of
the PMU.
Indicate the
software compiling NO NO Yes None
time of the PMU.
Indicates the
version description NO NO Yes None
of the PMU.
Indicates the
of the PMU.
Indicates the
PMU.
Indicates the PSU

intelligent shutdown
NO NO Yes None
capability of the
PMU.
of the PSU
NO NO Yes None
switch of the PMU.
Indicates the
execution result of
the setting of the NO NO Yes None
PSU intelligent
shutdown switch.
Indicates the
remaining
NO NO Yes None
discharging time of
a battery.
Indicates the
accumulated
charging time of a
battery, including NO NO Yes None
floating charging
time and equalized
charging time.
Indicates the
accumulated
sleeping time of a
battery. Battery NO NO Yes None
sleeping effectively
prolongs the battery
lifespan.
Indicates the
battery intelligent
management NO NO Yes None
capability of the
PMU.
Indicates the
battery intelligent
NO NO Yes None
management mode
of the PMU.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
cabinet where the
YES NO No None
PMU managing the
diesel generator is
located.
Indicates the
number of the
subrack where the
YES NO No None
PMU managing the
diesel generator is
located.
Indicates the
number of the slot
where the PMU
YES NO No None
managing the
diesel generator is
located.
Indicates whether
intelligent control of
the diesel generator
is enabled. When
intelligent control is
enabled, the PMU
automatically
controls the diesel NO NO No None
generator according
to the preset
parameters, thus
reducing the
operation cost of
the diesel
generator.
Indicates the
maximum rated
output power of the
diesel generator. It
should be
configured NO NO No None
according to the
rated output power
printed on the name
plate of the diesel
generator.
Indicates the oil
level of the diesel NO NO Yes None
generator.
Indicates the
current of the diesel NO NO Yes None
generator.
Indicates the total
running time of the NO NO Yes None
diesel generator.
Indicates the
number of the
PMU managing the
battery is located.
Indicates the
number of the
PMU managing the
battery is located.
Indicates the
number of the slot
where the PMU YES NO No None
managing the
battery is located.
(silkscreen:
APM30H), this
parameter is set as
required. If the
power cabinet is not
APM30 of version
301 or 302, this
parameter is set to
INNER. The
reasons are as
follows: In an
APM30 of version
301 or 302, the
battery temperature
sensor is connected
to different ports on
the APMI board by
the battery
temperature sensor
NO NO No None
cable, depending
on the installation
type of lead-acid
battery. When the
installation type is
INNER, the battery
temperature sensor
is connected to the
BAT_TEM1 port.
When the
installation type is
OUTER, the battery
temperature sensor
is connected to the
BAT_TEM2 port.
The configuration
data on the
maintenance
console must be set
Indicates the
scheduled boost
charging interval.
Batteries are boost-
charged at this
interval (in the unit
of day), which
keeps the batteries NO NO No None
fully charged. This
parameter is
configured
according to the
instructions
provided by
manufacturers.
Indicates the boost

charging voltage.
Boost charge is
used to quickly
recover the
capacity of
batteries. During
the boost charge,
the charging
voltage is relatively
high. After the
batteries are NO NO No None
discharged, the
system
automatically starts
boost charge on the
batteries. This
parameter is
configured
according to the
instructions
provided by
manufacturers.
Indicates the
capacity of battery
1. This parameter
should be set
according to the
NO NO No None
actual situation.
Incorrect
configuration may
reduce the life span
of the battery.
Indicates the
battery charging
current limiting
coefficient.
Charging coefficient
x Storage capacity
= Maximum
charging current.
When the charging
current is not
smaller than the
NO NO No None
maximum charging
current plus 5 A, an
ALM-25625 Battery
Current Abnormal
alarm is reported.
This parameter is
configured
according to the
instructions
provided by
manufacturers.
Indicates the
floating charging
voltage. Floating
charge is used to
compensate for the
power loss of the
batteries due to
self-discharge. The
floating charging
NO NO No None
voltage is lower
than the boost
charging voltage.
This parameter is
configured
according to the
instructions
provided by
manufacturers.
Indicates whether
to enable battery
disconnection NO NO No None
against high
temperature.
Indicates the
temperature above
which the battery is
powered off
NO NO No None
automatically under
the condition that
HtempShutdownFlg
is enabled.
Indicates whether
to enable battery
NO NO No None
power-off against
low voltage.
Indicates the
voltage below
which the battery is
powered off
NO NO No None
automatically under
the condition that
LvolShutdownFlg is
enabled.
Indicates the
increased or
reduced charging
voltage of every
battery when the
ambient
temperature is 1
degree Celsius
higher or lower than
NO NO No None
the standard
temperature
specified by
manufacturers. This
parameter should
be set according to
the instructions
provided by
manufacturers.
Indicates the lower
When the battery
temperature is
below the lower
NO NO No None
limit, an ALM-25650
Environmental
Temperature
Abnormal alarm is
reported.
Indicates the upper

When the battery
temperature
exceeds the upper
NO NO No None
limit, an ALM-25650
Environmental
Temperature
Abnormal alarm is
reported.
Indicates the
number of battery NO NO No None
groups.
Indicates the type

NO NO No None
of the battery.
Indicates the
number of times
NO NO Yes None
that the battery is
powered off.
Indicates the
number of times
that the battery is NO NO Yes None
charged in half an
hour.
Indicates the
number of times
that the battery is
charged when the
battery is charged NO NO Yes None
for more than half
an hour and less
than one hour or for
one hour.
Indicates the
number of times
that the battery is
charged when the
for more than one
hour and less than
two hours or for two
hours.
Indicates the
number of times
that the battery is
charged when the
for more than two
hours and less than
three hours or for
three hours.
Indicates the
number of times
that the battery is
charged when the
for more than three
hours and less than
four hours or for
four hours.
Indicates the
number of times
that the battery is
charged when the
for more than four
hours and less than
five hours or for five
hours.
Indicates the
number of times
that the battery is
charged when the
for more than five
hours and less than
six hours or for six
hours.
Indicates the
number of times
that the battery is
charged when the
for more than six
hours and less than
seven hours or for
seven hours.
Indicates the
number of times
that the battery is
charged when the
for more than seven
hours and less than
eight hours or for
eight hours.
Indicates the
number of times
charged in more
than eight hours.
Indicates the
number of times
discharged in half
an hour.
Indicates the
number of times
that the battery is
discharged when
the battery is
NO NO Yes None
discharged for more
than half an hour
and less than one
hour or for one
hour.
Indicates the
number of times
that the battery is
discharged when
the battery is NO NO Yes None
discharged for more
than one hour and
less than two hours
or for two hours.
Indicates the
number of times
that the battery is
discharged when
the battery is
NO NO Yes None
discharged for more
than two hours and
less than three
hours or for three
hours.
Indicates the
number of times
that the battery is
discharged when
the battery is
NO NO Yes None
discharged for more
than three hours
and less than four
hours or for four
hours.
Indicates the
number of times
that the battery is
discharged when
discharged for more
than four hours and
less than five hours
or for five hours.
Indicates the
number of times
that the battery is
discharged when
discharged for more
than five hours and
less than six hours
or for six hours.
Indicates the
number of times
that the battery is
discharged when
the battery is
NO NO Yes None
discharged for more
than six hours and
less than seven
hours or for seven
hours.
Indicates the
number of times
that the battery is
discharged when
the battery is
NO NO Yes None
discharged for more
than seven hours
and less than eight
hours or for eight
hours.
Indicates the
number of times
discharged in more
than eight hours.
Indicates the date

when the battery is
installed. The
scheduled tests for NO NO Yes None
the battery are
dependent on the
installation date.
Indicates the
capacity of battery
2. This parameter
should be set
according to the
NO NO No None
actual situation.
Incorrect
configuration may
reduce the life span
of the battery.
Indicates the
number of the
PMU managing the
battery is located.
Indicates the
number of the
PMU managing the
battery is located.
Indicates the
number of the slot
where the PMU YES NO No None
managing the
battery is located.
Indicates the
duration of
discharging the
battery with the
current of 0.05C10
to the moment
when the
discharging voltage
is terminated. C10
indicates the
nominal capacity of
the battery, and
0.05C10 indicates NO NO No None
that the battery is
discharged with the
current of 0.05 x
norminal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.05C10
indicates that the
battery is
discharged with the
current of 5 AH.
Indicates the
duration of
discharging the
battery with the
current of 0.1C10 to
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.1 x
the battery. For
example, if the
battery capacity is
100 AH, 0.1C10
indicates that the
battery is
discharged with the
current of 10 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.2 x
the battery. For
example, if the
battery capacity is
100 AH, 0.2C10
indicates that the
battery is
discharged with the
current of 20 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.3 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.3C10
indicates that the
battery is
discharged with the
current of 30 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.4 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.4C10
indicates that the
battery is
discharged with the
current of 40 AH.
Indicates the
duration of
discharging the
battery with the
current x 0.5C10 to
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.5 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.5C10
indicates that the
battery is
discharged with the
current of 50 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.6 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.6C10
indicates that the
battery is
discharged with the
current of 60 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.7 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.7C10
indicates that the
battery is
discharged with the
current of 70 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.8 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.8C10
indicates that the
battery is
discharged with the
current of 80 AH.
Indicates the
duration of
discharging the
battery with the
the moment when
the discharging
voltage is
terminated. C10
indicates the
nominal capacity of
the battery, and
that the battery is
discharged with the
current of 0.9 x
nominal capacity of
the battery. For
example, if the
battery capacity is
100 AH, 0.9C10
indicates that the
battery is
discharged with the
current of 90 AH.
Indicates the
charging efficiency
of batteries. The
battery efficiency is
a percentage of
battery
performance to the
normal battery
capacity. For NO NO No None
example, a normal
battery can supply
power for 10 hours.
If a battery can
supply power for
only eight hours, its
battery efficiency is
80%.
Indicates the end

voltage of the NO NO No None
discharging test.
Indicates the
quantity of battery NO NO No None
in the battery group.
Indicates the time

limit of the NO NO No None
discharging test.
Indicates the time

limit for the
simplified
discharging test.
There are two types
of discharging tests
for a battery: a
standard test and a
NO NO No None
simplified test. A
standard test
calculates the
battery efficiency,
and a simplified test
judges only the
quality of the
battery.
Indicates the end

voltage of the
NO NO No None
simple discharging
test.
Indicates the test
mode. It specifies
whether to use the
automatic test and
which automatic
test mode is used.
There are four
types of test
modes:
NOAUTOTEST (No
Auto Test), PERIOD
(Period Auto Test),
POWERCUT
(Power Off Auto
Test), and
PERIODPOWERC
UT (Period and
Power Off Auto
Test). No Auto Test:
NO NO No None
indicates that the
battery test is
launched and
controlled by the
user. Period Auto
Test: indicates that
the battery test is
launched
automatically by the
system as
scheduled. Power
Off Auto Test:
indicates that the
battery test is
launched
system after the AC
power supply is cut
off.
Indicates the time

limit of the
NO NO No None
scheduled
discharging test.
Indicates the time
limit for the
discharging test
delay when the
power is off or the
discharging test is
launched
automatically. The
NO NO No None
interval between
two battery tests
must be greater
than this time limit.
Otherwise, the
execution of the
STR BATTST
command fails.
Indicates the type

There are two types
of battery tests:
STANDARD(Standa
rd Test) and
SIMPLE(Simple
Test). Standard Test
is used to calculate
NO NO Yes None
the efficiency of the
battery. Simple Test
is used only to
judge the quality of
the battery, but not
to calculate the
efficiency of the
battery. This test
takes a short time.
Indicates the test

start date, which is
NO NO Yes None
in the format of
YYYY/MM/DD.
Indicates the end

reason of the NO NO Yes None
battery test.
NO NO Yes None
Indicates the
battery efficiency.
The battery is
NO NO Yes None
normal when the
result is between
80% and 100%.
Indicates the
continued
NO NO Yes None
discharge duration
of the battery.
Indicates the
voltage of the
NO NO Yes None
battery when the
discharge is ended.
Indicates the
average current in
NO NO Yes None
the process of the
battery discharge.
Indicates the
accumulated
discharged power
NO NO Yes None
(Ah) from the
beginning of
discharge.
Indicates the
current temperature NO NO Yes None
of the battery.
Indicates the
number of the
YES NO No None
cabinet where the
PSU is located.
Indicates the
number of the
YES NO No None
subrack where the
PSU is located.
Indicates the
number of the slot
YES NO No None
where the PSU is
located.
Indicates the
running status of NO NO Yes None
the PSU.
Indicates the
of the PSU.
Indicates the
PSU.
Indicates the PCB

NO NO Yes None
version of the PSU.
Indicates the
erasable
device (EPLD)
version of the PSU.
Indicates the
compiling time of
the software NO NO Yes None
program in the
PSU.
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
cabinet number of
the board where the YES NO No None
output port is
located.
Indicates the
subrack number of
output port is
located.
Indicates the slot
number of the
board where the YES NO No None
output port is
located.
Indicates the
output port.
Indicates the name LBFD-004012 /

NO NO No
of the output port. TDLBFD-004012
Indicates the
enabled/disabled LBFD-004012 /
NO NO No
state of the output TDLBFD-004012
port.
Indicates the
cabinet number of
YES YES No None
the board where the
port is located.
Indicates the
subrack number of
YES YES No None
the board where the
port is located.
Indicates the slot
number of the
YES YES No None
board where the
port is located.
Indicates the port
YES YES No None
number.
Indicates the
enabled/disabled
state of the port.
Alarms can be
LBFD-004012 /
detected and NO NO No
TDLBFD-004012
reported through
the port only when
the state of the port
is ON.
Indicates the alarm

ID bound to the
alarm port. This
LBFD-004012 /
parameter is NO NO No
TDLBFD-004012
reported as the ID
of the alarm
detected at the port.
Indicates the alarm
port types: analog
alarm port and
digital alarm port.
An analog alarm
port is used to
monitor the external
environment that
changes
continuously. The
port is supported
only by the EMU. A
digital alarm port is
LBFD-004012 /
used to monitor the NO NO No
TDLBFD-004012
external
environment of
which the change is
indicated in
Boolean or discrete
values. It is
contained in the
EMU, PMU, TCU,
FMU, RRU, and
power boards. The
SC48200 PMU
does not support
digital ports.
Indicates the alarm

level. This
parameter specifies
whether alarms
generated by the
sensor over the port LBFD-004012 /
NO NO No
are in high or low TDLBFD-004012
voltage. The alarm
level is set
according to the
type of external
sensor.
Indicates the alarm
upper limit. If the
environment
measurement value
is greater than the
alarm upper limit
configured for the
sensor, the alarm is
reported.
Environment
measurement value
= Measurement
lower limit +
(Measurement
upper limit -
LBFD-004012 /
Measurement lower NO NO No
TDLBFD-004012
limit) x (Observed
electric current or
voltage - Output
lower limit)/(Output
upper limit - Output
lower
limit).Temperature
is measured in the
unit of degree
Celsius, voltage is
measured in the
unit of volt, and
current is measured
in the unit of
milliampere.
Indicates the alarm
lower limit. If the
environment
measurement value
is smaller than the
alarm lower limit
configured for the
sensor, the alarm is
reported.
Environment
measurement value
= Measurement
lower limit +
(Measurement
upper limit -
LBFD-004012 /
Measurement lower NO NO No
TDLBFD-004012
limit) x (Observed
electric current or
voltage - Output
lower limit)/(Output
upper limit - Output
lower
limit).Temperature
is measured in the
unit of degree
Celsius, voltage is
measured in the
unit of volt, and
current is measured
in the unit of
milliampere.
Indicates the
sensor type. The
user can set the
sensor type to
LBFD-004012 /
current type or NO NO No
TDLBFD-004012
voltage type
according to the
actual external
sensor.
Indicates the
measurement
upper limit of the
analog port. The
range is set based
on the actual
situations such as
the temperature
and LBFD-004012 /
NO NO No
humidity.Temperatu TDLBFD-004012
re is measured in
the unit of degree
Celsius, voltage is
measured in the
unit of volt, and
current is measured
in the unit of
milliampere.
Indicates the
measurement lower
limit of the analog
port. The range is
set based on the
actual situations
such as the
temperature and
LBFD-004012 /
humidity.Temperatu NO NO No
TDLBFD-004012
re is measured in
the unit of degree
Celsius, voltage is
measured in the
unit of volt, and
current is measured
in the unit of
milliampere.
Indicates the upper

limit of the output
signals from the
analog port. For
sensors of either
LBFD-004012 /
the current type or NO NO No
TDLBFD-004012
voltage type, the
upper limit should
be set according to
the specifications of
the sensor.
Indicates the lower
limit of the output
signals from the
analog port. For
sensors of either
LBFD-004012 /
the current type or NO NO No
TDLBFD-004012
voltage type, the
lower limit should
be set according to
the specifications of
the sensor.
Indicates the
connection type
NO NO No None
supported by the
NE.
Indicates the
authentication
mode of the SSL
connection.
If the authentication
mode is set to
NONE, the NE
does not verify the
certificate of the
M2000 or LMT
during setup of an
SSL connection. In
this case, both
parties must
support the same NO NO No None
algorithm for
anonymous
authentication.
If authentication
using the peer
certificate is used,
the NE must verify
the certificate of the
M2000 or LMT
during setup of an
SSL connection. If
the certificate
verification fails, the
SSL connection
cannot be set up.
Indicates the
the AAU.
Indicates the
subrack number of YES YES No None
the AAU.
Indicates the slot

YES YES No None
number of the AAU.
Indicates the AAU

NO NO No None
name.
Indicates the RRU

NO YES No None
type of the AAU.
Indicates the
NO NO No None
administrative state.
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.
power.
When this switch is
set to OFF, an RF
module decreases
the total TX power
of the TX channel
by 3 dB to minimize
the impacts of high
VSWR. Different
scenarios are
described as
follows:
1. An RF module
degrades its power
by decreasing the
TX power of
carriers sharing TX
channels by 3 dB.
2. In the scenario NO NO No None
where two TX
channels are
configured with
transmit diversity
and MIMO, the TX
power of one
channel is
decreased by 3 dB
if a major VSWR
alarm is generated
in this channel.
Meanwhile, the TX
power of the other
channel also needs
to be decreased by
3 dB for the power
balance of TX
channels.
Indicates the
VSWR alarm post-
processing
threshold. If the
VSWR alarm post-
processing switch is
set to ON and the
VSWR is greater
than the threshold,
NO NO No None
post-processing is
performed to shut
down the TX
channel. In this
case, the TX
channel cannot be
open automatically
after the VSWR is
normal.
is greater than the
threshold, a VSWR
Abnormal alarm is
reported.
It is recommended
that the VSWR
alarm threshold be
set according to the
VSWR required by
the engineering
quality to reduce
the probability that
the VSWR alarm is
reported falsely.
To stabilize the
false alarm
probability to 1%,
0.1%, and 0.01%,
you need to set the
NO NO No None
VSWR alarm
threshold to the
following
recommended
values:
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.4, the
recommended
thresholds are 1.8,
2.0, and 2.4,
respectively.
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.5, the
Indicates the
position of the
RRU, RFU on the
chain or ring. It is NO YES No None
calculated from the
start port one by
one.
Indicates the ID of
the RRU or RFU NO YES No None
chain/ring.
Indicates the
position where the
RRU or RFU is
installed in the
topology. The main
NO NO No None
chain/ring is the
one connected to
the optical port on
the baseband
processing board.
Indicates the
working mode of
the RRU or RFU.
MRFU, MRRU, and
PRRU support both
single-mode and
multi-mode base NO YES No None
stations. LRFU
supports only
LTE_FDD and
LRRU supports
LTE_TDD and
LTE_FDD.
Indicates the
number of RX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of TX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of carriers
NO NO Yes None
on each RX
channel.
Indicates the
number of carriers
NO NO Yes None
on each TX
channel.
Indicates the
minimum uplink
frequency
supported by the
RRU. For example,
if this parameter is
NO NO Yes None
set to 9250, the
minimum uplink
frequency of the
RRU is 9250 x 0.1
MHz, which equals
to 925 MHz.
Indicates the
maximum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9450, the
maximum uplink
frequency of the
RRU is 9450 x 0.1
MHz, which equals
to 945 MHz.
Indicates the
minimum downlink
frequency
supported by the
RRU. For example,
this parameter is
NO NO Yes None
set to 9650, the
minimum downlink
frequency of the
RRU is 9650 x 0.1
MHz, which equals
to 965 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9850, the
maximum downlink
frequency of the
RRU is 9850 x 0.1
MHz, which equals
to 985 MHz.
Indicates the
maximum output
power per TX NO NO Yes None
channel in the
RRU/RFU.
Indicates the UL
NO NO Yes None
channel gain.
Indicates the
bandwidth
supported by each NO NO Yes None
TX channel in the
uplink.
Indicates the
PA.
Indicates the
of the RRU or RFU.
Indicates the
RRU/RFU level on
NO NO Yes None
the trunk of the
chain/ring.
number of the RRU NO NO Yes None
or RFU.
Indicates the
standards that are
supported by the
RRU or RFU. NULL NO NO Yes None
means that the
standards fail to be
obtained.
Indicates the
access direction of NO NO Yes None
the service plane.
Indicates the
maximum output
power of TX unit 0 NO NO Yes None
(single carrier) of
the RRU or RFU.
Indicates the
maximum output
(multiple carriers) of
the RRU or RFU.
Indicates the
bandwidth
TX channel in the
downlink.
Indicates the
physical indicator of NO NO Yes None
the RRU.
Indicates the
periodical report
switch for the Bit
Error Rate (BER)
on the link. If the NO NO Yes None
switch is set to ON,
the result of BER
test is reported
periodically.
Indicates the test
time. When the test
time is over, the
system NO NO Yes None
automatically stops
the test and reports
the test result.
Indicates the
interference check
mode.
POW_IQ_MODE
indicates that both
power and IQ data
is collected.
NO NO Yes None
POW_MODE
indicates that only
power data is
collected.
IQ_MODE indicates
that only IQ data is
collected.
Indicates the short-
duration power NO NO Yes None
statistics period.
Indicates the
duration for a single
NO NO Yes None
collection of power
statistics.
Indicates the UL
NO NO Yes None
frequency.
Indicates the bit
NO NO Yes None
error rate.
Indicates the
interference check NO NO Yes None
sampling result.
Indicates the set

NO NO Yes None
type.
Indicates the BER

threshold. The BER
NO NO Yes None
threshold reflects
the link quality.
Indicates the
NO NO Yes None
Linerate.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
NO NO No None
power.
When this switch is
set to OFF, an RF
module decreases
the total TX power
of the TX channel
by 3 dB to minimize
the impacts of high
VSWR. Different
scenarios are
described as
follows:
1. An RF module
degrades its power
by decreasing the
TX power of
carriers sharing TX
channels by 3 dB.
where two TX
channels are
configured with
transmit diversity
and MIMO, the TX
power of one
channel is
decreased by 3 dB
if a major VSWR
alarm is generated
in this channel.
Meanwhile, the TX
power of the other
channel also needs
to be decreased by
3 dB for the power
balance of TX
channels.
Indicates the
VSWR alarm post-
processing
threshold. If the
VSWR alarm post-
set to ON and the
VSWR is greater
than the threshold,
NO NO No None
post-processing is
performed to shut
down the TX
channel. In this
case, the TX
channel cannot be
open automatically
after the VSWR is
normal.
is greater than the
threshold, a VSWR
Abnormal alarm is
reported.
It is recommended
that the VSWR
alarm threshold be
VSWR required by
the engineering
quality to reduce
the VSWR alarm is
reported falsely.
To stabilize the
false alarm
probability to 1%,
0.1%, and 0.01%,
you need to set the
NO NO No None
VSWR alarm
threshold to the
following
recommended
values:
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.4, the
recommended
thresholds are 1.8,
2.0, and 2.4,
respectively.
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.5, the
Indicates the
position of the
RRU, RFU on the
calculated from the
start port one by
one.
Indicates the ID of
chain/ring.
Indicates the
position where the
RRU or RFU is
installed in the
topology. The main
NO NO No None
chain/ring is the
one connected to
the optical port on
the baseband
processing board.
Indicates the
working mode of
the RRU or RFU.
MRFU, MRRU, and
PRRU support both
single-mode and
stations. LRFU
supports only
LTE_FDD and
LRRU supports
LTE_TDD and
LTE_FDD.
Indicates the
number of RX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of TX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of carriers
NO NO Yes None
on each RX
channel.
Indicates the
number of carriers
NO NO Yes None
on each TX
channel.
Indicates the
minimum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9250, the
minimum uplink
frequency of the
RRU is 9250 x 0.1
MHz, which equals
to 925 MHz.
Indicates the
maximum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9450, the
maximum uplink
frequency of the
RRU is 9450 x 0.1
MHz, which equals
to 945 MHz.
Indicates the
minimum downlink
frequency
supported by the
RRU. For example,
this parameter is
NO NO Yes None
set to 9650, the
minimum downlink
frequency of the
RRU is 9650 x 0.1
MHz, which equals
to 965 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9850, the
maximum downlink
frequency of the
RRU is 9850 x 0.1
MHz, which equals
to 985 MHz.
Indicates the
maximum output
channel in the
RRU/RFU.
Indicates the UL
NO NO Yes None
channel gain.
Indicates the
bandwidth
TX channel in the
uplink.
Indicates the
PA.
Indicates the
of the RRU or RFU.
Indicates the
RRU/RFU level on
NO NO Yes None
the trunk of the
chain/ring.
or RFU.
Indicates the
standards that are
supported by the
means that the
obtained.
Indicates the
the service plane.
Indicates the
maximum output
(single carrier) of
the RRU or RFU.
Indicates the
maximum output
the RRU or RFU.
Indicates the
bandwidth
TX channel in the
downlink.
Indicates the
the RRU.
Indicates the
periodical report
switch for the Bit
Error Rate (BER)
the result of BER
test is reported
periodically.
Indicates the test
time. When the test
time is over, the
automatically stops
the test result.
Indicates the
interference check
mode.
POW_IQ_MODE
indicates that both
power and IQ data
is collected.
NO NO Yes None
POW_MODE
indicates that only
power data is
collected.
IQ_MODE indicates
collected.
statistics period.
Indicates the
NO NO Yes None
collection of power
statistics.
Indicates the UL
NO NO Yes None
frequency.
Indicates the bit
NO NO Yes None
error rate.
Indicates the
sampling result.
Indicates the set

NO NO Yes None
type.
Indicates the BER

threshold. The BER
NO NO Yes None
threshold reflects
the link quality.
Indicates the
NO NO Yes None
Linerate.
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
RFU is located.
Indicates the
number of the
YES YES No None
subrack where the
RFU is located.
Indicates the slot

YES YES No None
number of the RFU.
Indicates the type

NO YES No None
of the RFU.
Indicates the
NO NO No None
Indicates the alarm

The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.
power.
When this switch is
set to OFF, an RF
module decreases
the total TX power
of the TX channel
by 3 dB to minimize
the impacts of high
VSWR. Different
scenarios are
described as
follows:
1. An RF module
degrades its power
by decreasing the
TX power of
carriers sharing TX
channels by 3 dB.
where two TX
channels are
configured with
transmit diversity
and MIMO, the TX
power of one
channel is
decreased by 3 dB
if a major VSWR
alarm is generated
in this channel.
Meanwhile, the TX
power of the other
channel also needs
to be decreased by
3 dB for the power
balance of TX
channels.
Indicates the
VSWR alarm post-
processing
threshold. If the
VSWR alarm post-
set to ON and the
VSWR is greater
than the threshold,
NO NO No None
post-processing is
performed to shut
down the TX
channel. In this
case, the TX
channel cannot be
open automatically
after the VSWR is
normal.
is greater than the
threshold, a VSWR
Abnormal alarm is
reported.
It is recommended
that the VSWR
alarm threshold be
VSWR required by
the engineering
quality to reduce
the VSWR alarm is
reported falsely.
To stabilize the
false alarm
probability to 1%,
0.1%, and 0.01%,
you need to set the
NO NO No None
VSWR alarm
threshold to the
following
recommended
values:
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.4, the
recommended
thresholds are 1.8,
2.0, and 2.4,
respectively.
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.5, the
Indicates the
position of the
RRU, RFU on the
calculated from the
start port one by
one.
Indicates the ID of
chain/ring.
Indicates the
position where the
RRU or RFU is
installed in the
topology. The main
NO NO No None
chain/ring is the
one connected to
the optical port on
the baseband
processing board.
Indicates the
working mode of
the RRU or RFU.
MRFU, MRRU, and
PRRU support both
single-mode and
stations. LRFU
supports only
LTE_FDD and
LRRU supports
LTE_TDD and
LTE_FDD.
Indicates the
number of RX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of TX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of carriers
NO NO Yes None
on each RX
channel.
Indicates the
number of carriers
NO NO Yes None
on each TX
channel.
Indicates the
minimum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9250, the
minimum uplink
frequency of the
RRU is 9250 x 0.1
MHz, which equals
to 925 MHz.
Indicates the
maximum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9450, the
maximum uplink
frequency of the
RRU is 9450 x 0.1
MHz, which equals
to 945 MHz.
Indicates the
minimum downlink
frequency
supported by the
RRU. For example,
this parameter is
NO NO Yes None
set to 9650, the
minimum downlink
frequency of the
RRU is 9650 x 0.1
MHz, which equals
to 965 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9850, the
maximum downlink
frequency of the
RRU is 9850 x 0.1
MHz, which equals
to 985 MHz.
Indicates the
maximum output
channel in the
RRU/RFU.
Indicates the UL
NO NO Yes None
channel gain.
Indicates the
bandwidth
TX channel in the
uplink.
Indicates the
PA.
Indicates the
of the RRU or RFU.
Indicates the
RRU/RFU level on
NO NO Yes None
the trunk of the
chain/ring.
or RFU.
Indicates the
standards that are
supported by the
means that the
obtained.
Indicates the
the service plane.
Indicates the
maximum output
(single carrier) of
the RRU or RFU.
Indicates the
maximum output
the RRU or RFU.
Indicates the
bandwidth
TX channel in the
downlink.
Indicates the
the RRU.
Indicates the
periodical report
switch for the Bit
Error Rate (BER)
the result of BER
test is reported
periodically.
Indicates the test
time. When the test
time is over, the
automatically stops
the test result.
Indicates the
interference check
mode.
POW_IQ_MODE
indicates that both
power and IQ data
is collected.
NO NO Yes None
POW_MODE
indicates that only
power data is
collected.
IQ_MODE indicates
collected.
statistics period.
Indicates the
NO NO Yes None
collection of power
statistics.
Indicates the UL
NO NO Yes None
frequency.
Indicates the bit
NO NO Yes None
error rate.
Indicates the
sampling result.
Indicates the set

NO NO Yes None
type.
Indicates the BER

threshold. The BER
NO NO Yes None
threshold reflects
the link quality.
Indicates the
NO NO Yes None
Linerate.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the
number of the
YES NO No None
cabinet where the
RRU is located.
Indicates the
number of the
YES YES No None
subrack where the
RRU is located.
Indicates the
number of the slot
YES NO No None
where the RRU is
located.
Indicates the RRU

NO NO No None
name.
Indicates the type
NO YES No None
of the RRU.
Indicates the test

NO NO Yes None
type.
Indicates the test
NO NO Yes None
time.
Indicates the
difference of the
RSSI voltage
threshold between
full power and no
power during the
NO NO Yes None
PIMOFFLINE test.
If the difference is
greater than this
threshold,
intermodulation
interference exists.
Indicates the
antenna port.
Indicates the test

NO NO Yes None
result.
Indicates the value

NO NO Yes None
of the RTWP.
Indicates the
difference of the NO NO Yes None
RTWP.
Indicates the
maximum value of NO NO Yes None
the RTWP.
Indicates the
NO NO No None
Indicates the alarm
The alarm state of
the board can be
normal, warning,
NO NO Yes None
details about the
definition of Alarm
Status, see ITU-T
X.731.
Indicates the
the board, which
can be set to
Enabled or
Disabled. Enabled
indicates that
NO NO Yes None
services can be
carried on the
board. Disabled
indicates that no
service can be
carried on the
board.
Indicates the
physical operation
which can be
Uninstalled,
Inconsistent,
Unconfigured,
Power off, Fault,
Communication
combination of
example, if a board
is not configured
and fails to
communicate with
the main control
and transmission
board, the physical
operation status of
the board is
Unconfigured,
Communication
lost.
Indicates the E-
a maximum of 2
KB. It is used to
record the
information about
equipment such as
the board, sub-
board, or optical
module.
Indicates the type
NO NO Yes None
of the board.
Indicates the bar
or the cabinet.
Indicates the
description about
the services and
NO NO Yes None
functions provided
by the board or the
cabinet.
Indicates the
manufacturing date
NO NO Yes None
of the board or the
cabinet.
Indicates the
manufacturer of the
NO NO Yes None
board or the
cabinet.
Indicates the issue
board.
Indicates the type

NO NO Yes None
of a board.
Indicates the CPU

NO NO Yes None
or DSP usage.
NO NO Yes None
number of a board.

type of a board,
NO NO Yes None
which is CPU or
DSP.
Indicates the
board.
Indicates the
power amplifier.
NO NO Yes None
of the operation.
Indicates the
service type of the
CPU or DSP of the
board. The service
types of the DSP
and downlink
services. The
CPU consist of
Master and Slave.
Indicates the type

NO NO Yes None
of the device.
power.
When this switch is
set to OFF, an RF
module decreases
the total TX power
of the TX channel
by 3 dB to minimize
the impacts of high
VSWR. Different
scenarios are
described as
follows:
1. An RF module
degrades its power
by decreasing the
TX power of
carriers sharing TX
channels by 3 dB.
where two TX
channels are
configured with
transmit diversity
and MIMO, the TX
power of one
channel is
decreased by 3 dB
if a major VSWR
alarm is generated
in this channel.
Meanwhile, the TX
power of the other
channel also needs
to be decreased by
3 dB for the power
balance of TX
channels.
Indicates the
VSWR alarm post-
processing
threshold. If the
VSWR alarm post-
set to ON and the
VSWR is greater
than the threshold,
NO NO No None
post-processing is
performed to shut
down the TX
channel. In this
case, the TX
channel cannot be
open automatically
after the VSWR is
normal.
is greater than the
threshold, a VSWR
Abnormal alarm is
reported.
It is recommended
that the VSWR
alarm threshold be
VSWR required by
the engineering
quality to reduce
the VSWR alarm is
reported falsely.
To stabilize the
false alarm
probability to 1%,
0.1%, and 0.01%,
you need to set the
NO NO No None
VSWR alarm
threshold to the
following
recommended
values:
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.4, the
recommended
thresholds are 1.8,
2.0, and 2.4,
respectively.
When the VSWR
required by the
engineering quality
is smaller than or
equal to 1.5, the
Indicates the
position of the
RRU, RFU on the
calculated from the
start port one by
one.
Indicates the ID of
chain/ring.
Indicates the
position where the
RRU or RFU is
installed in the
topology. The main
NO NO No None
chain/ring is the
one connected to
the optical port on
the baseband
processing board.
Indicates the
working mode of
the RRU or RFU.
MRFU, MRRU, and
PRRU support both
single-mode and
stations. LRFU
supports only
LTE_FDD and
LRRU supports
LTE_TDD and
LTE_FDD.
Indicates the
number of RX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of TX
NO YES No None
channels of the
RRU or RFU.
Indicates the
number of carriers
NO NO Yes None
on each RX
channel.
Indicates the
number of carriers
NO NO Yes None
on each TX
channel.
Indicates the
minimum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9250, the
minimum uplink
frequency of the
RRU is 9250 x 0.1
MHz, which equals
to 925 MHz.
Indicates the
maximum uplink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9450, the
maximum uplink
frequency of the
RRU is 9450 x 0.1
MHz, which equals
to 945 MHz.
Indicates the
minimum downlink
frequency
supported by the
RRU. For example,
this parameter is
NO NO Yes None
set to 9650, the
minimum downlink
frequency of the
RRU is 9650 x 0.1
MHz, which equals
to 965 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU. For example,
NO NO Yes None
set to 9850, the
maximum downlink
frequency of the
RRU is 9850 x 0.1
MHz, which equals
to 985 MHz.
Indicates the
maximum output
channel in the
RRU/RFU.
Indicates the UL
NO NO Yes None
channel gain.
Indicates the
bandwidth
TX channel in the
uplink.
Indicates the
PA.
Indicates the
of the RRU or RFU.
Indicates the
RRU/RFU level on
NO NO Yes None
the trunk of the
chain/ring.
or RFU.
Indicates the
standards that are
supported by the
means that the
obtained.
Indicates the
the service plane.
Indicates the
maximum output
(single carrier) of
the RRU or RFU.
Indicates the
maximum output
the RRU or RFU.
Indicates the
bandwidth
TX channel in the
downlink.
Indicates the
the RRU.
Indicates the
periodical report
switch for the Bit
Error Rate (BER)
the result of BER
test is reported
periodically.
Indicates the test
time. When the test
time is over, the
automatically stops
the test result.
Indicates the
interference check
mode.
POW_IQ_MODE
indicates that both
power and IQ data
is collected.
NO NO Yes None
POW_MODE
indicates that only
power data is
collected.
IQ_MODE indicates
collected.
statistics period.
Indicates the
NO NO Yes None
collection of power
statistics.
Indicates the UL
NO NO Yes None
frequency.
Indicates the bit
NO NO Yes None
error rate.
Indicates the
sampling result.
Indicates the set

NO NO Yes None
type.
Indicates the BER

threshold. The BER
NO NO Yes None
threshold reflects
the link quality.
Indicates the
NO NO Yes None
Linerate.

NO NO Yes None
name of the BS.
Indicates the
the board.
Indicates the
the board.
Indicates the
of the board.
Indicates the test
NO NO Yes None
time.
Indicates the test

NO NO Yes None
result.
[1162-1513] Offset:
1575 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1537-1738] Offset:
1805 Special
Frequencies
Channel Number:
(1887, 1912, 1937,
1962, 1987, 2012,
2037, 2062, 2087)
Offset: 1735.1
Band5: Common
Frequencies
[4357-4458] Offset:
0 Special
Frequencies
Channel Number:
(1007, 1012, 1032,
1037, 1062, 1087)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4387-4413] Offset:
0 Special
Frequencies
Channel Number:
(1037, 1062) Offset:
670.1 Band7:
Common
Frequencies
Band3: Common
Frequencies
Channel Number:
[937-1288] Offset:
1525 Special
Frequencies
Channel Number:
none Offset: 0
Band4: Common
Frequencies
Channel Number:
[1312-1513] Offset:
1450 Special
Frequencies
Channel Number:
(1662, 1687, 1712,
1737, 1762, 1787,
1812, 1837, 1862)
Offset: 1380.1
NO NO Yes None
Band5: Common
Frequencies
Channel Number:
[4132-4233] Offset:
0 Special
Frequencies
Channel Number:
(782, 787, 807,
812, 837, 862)
Offset: 670.1
Band6: Common
Frequencies
Channel Number:
[4162-4188] Offset:
0 Special
Frequencies
Channel Number:
(812, 837) Offset:
670.1 Band7:
Indicates the ID of
the RRU chain. It
uniquely identifies a YES YES No None
chain within a base
station.
Indicates the type
NO YES No None
of the topology.
Indicates the
backup mode of the
RRU chain/ring.
There are two
modes: cold backup
and hot backup.
Cold backup
indicates that when
the link on one end
of the chain/ring
fails, the service is
disrupted for a short
period of time, and
then re-established
on the other end of
the chain/ring. Hot
backup indicates
that when the link
on one end of the NO NO No None
chain/ring fails, the
service is taken
over by the other
end of the
chain/ring
immediately. There
is only one RRU on
the chain/ring in hot
backup mode.In the
RRUCHAIN MO, if
TT is set to RING
and BM is set to
HOT, the head
CPRI port and the
tail CPRI port of the
RRU ring must be
on different
baseband boards.
Indicates the
cabinet number of
head CPRI port is
located.
Indicates the
subrack number of
head CPRI port is
located.
Indicates the slot
number of the
board where the NO YES No None
head CPRI port is
located.
Indicates the
number of the head NO YES No None
CPRI port.
Indicates the
cabinet number of
tail CPRI port is
located.
Indicates the
subrack number of
tail CPRI port is
located.
Indicates the slot
number of the
board where the tail NO YES No None
CPRI port is
located.
Indicates the
number of the tail NO YES No None
CPRI port.
Indicates the
breakpoint position
1 on the chain/ring.
parameter is set to
255, the breakpoint
is disabled.
Indicates the
breakpoint position
2 on the chain/ring.
parameter is set to
255, the breakpoint
is disabled.
Indicates the
access type of the
RRU. When
AccessType is set
to the local port, the
LBBP is connected
to the RRU/RFU
through the CPRI
port. When
AccessType is set NO NO No None
to the peer port, the
peer LBBP is
directly connected
to the RRU/RFU,
and the local LBBP
is connected to the
peer LBBP through
the IDX2 port on
the backplane.
Indicates the user-

defined rate. The
value AUTO
indicates the the
auto negotiation
mode is adopted.
The value 1.25
indicates that the
CPRI rate is 1.25
Gbit/s. The value
2.5 indicates that
NO NO No None
the CPRI rate is 2.5
Gbit/s. The value
4.9 indicates that
Gbit/s. The value
6.1 indicates that
Gbit/s. The value
9.8 indicates that
Gbit/s.
Indicates the level
NO NO Yes None
of the RRU chain.
Indicates the
number of RRUs
NO NO Yes None
carried on the RRU
chain/ring.
Indicates the
cabinet number of
the RRU where the YES NO No None
RX channel of the
RRU is located.
Indicates the
subrack number of
the RRU where the YES YES No None
RX channel of the
RRU is located.
Indicates the slot
number of the RRU
where the RX YES NO No None
channel of the RRU
is located.
Indicates the
number of the RX
YES YES No None
channel of the
RRU.
Indicates the logical
switch of the RX
channel of the
RRU, which is set
to ON by default. NO NO No None
The switch can be
set by running the
MOD RXBRANCH
command.
Indicates the
attenuation of the
NO NO No None
RX channel of the
RRU.
physical status of
the RX channel of
the RRU, the switch
of which is set to
ON by default.
When the logical
switch of the RX
channel is OFF, the
physical switch of
NO NO Yes None
the RX channel
must be OFF. When
the logical switch of
the RX channel is
ON and the RRU is
running properly,
the physical switch
of the RX channel
of the RRU can be
ON.
Indicates the
minimum uplink
frequency
supported by the
RRU band 1. For
example, if this
NO NO Yes None
parameter is set to
9250, the minimum
uplink frequency of
the RRU is 9250 x
0.1 MHz, which
equals to 925 MHz.
Indicates the
maximum uplink
frequency
supported by the
RRU band 1. For
example, if this
NO NO Yes None
parameter is set to
9450, the maximum
uplink frequency of
the RRU is 9450 x
0.1 MHz, which
equals to 945 MHz.
Indicates the
bandwidth
supported by each
TX channel band 1
NO NO Yes None
in the downlink.
This bandwidth is
an instantaneous
bandwidth.
Indicates the
minimum uplink
frequency
supported by the
RRU band 2.This
parameter is
NULL,when the
RRU does not
supported many NO NO Yes None
bands. For
example, if this
parameter is set to
9250, the minimum
uplink frequency of
the RRU is 9250 x
0.1 MHz, which
equals to 925 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU band 2.This
parameter is
NULL,when the
RRU does not
bands. For
example, if this
parameter is set to
9850, the maximum
downlink frequency
of the RRU is 9850
x 0.1 MHz, which
equals to 985 MHz.
Indicates the
bandwidth
supported by each
TX channel band 2
in the uplink. This
bandwidth is an
NO NO Yes None
instantaneous
bandwidth. This
parameter is NULL,
when the RRU
does not supported
multi-bands.
Indicates the
cabinet number of
TX channel of the
RRU is located.
Indicates the
subrack number of
TX channel of the
RRU is located.
Indicates the slot
number of the RRU
where the TX YES YES No None
channel of the RRU
is located.
Indicates the
number of the TX
YES YES No None
channel of the
RRU.
Indicates the logical
switch of the TX
channel of the
RRU. This switch is
used to open or
close the TX
channel. The logical
switch of the TX
channel and the
ARFCNs on the TX
channel determine
the state of the NO NO No None
physical switch of
the TX channel:
When this switch is
ON and the TX
channel is
configured with
ARFCNs, the
physical switch is
ON. In other cases,
the physical switch
is OFF.
Indicates the
current VSWR of
the TX channel.
When the TX power
is relatively low , the
S/N of the reflected
signal passing
through the
NO NO Yes None
detector channel is
relatively low, which
leads to the
inaccuracy of the
VSWR calculation,
the value of this
field will be
displayed as NULL.
physical status of
the TX channel of
the RRU. The
logical switch of the
TX channel and the
ARFCN on the TX
channel determine
the state of the
physical switch of
the TX channel: If NO NO Yes None
the logical switch of
a TX channel is ON
and the ARFCN is
configured for the
TX channel, the
physical switch of
the TX channel is
ON. In other cases,
the physical switch
is OFF.
Indicates the
adjusted output
power on the TX NO NO Yes None
channel of the
RRU.
Indicates the test
frequency. Different
types of RRUs
support different
frequency ranges.
Therefore, the
frequency of the NO NO Yes None
cell is used as the
VSWR test
frequency. The
default test
frequency of an
RRU is 65535.
Indicates the
relative TX power. If
this parameter is
NO NO Yes None
not specified, the
maximum power is
used by all boards.
Indicates the
maximum duration
NO NO Yes None
of the VSWR test
on one channel.
Indicates the
NO NO Yes None
number of the site.
Indicates the
sector.
Indicates the name
NO NO Yes None
of the site.
Indicates the
maximum output
power on the TX
channel. The
adjustment step is 1
W (1000 mW).
NO NO Yes None
When the output
power is set to 0
mW, the maximum
output power is
unlocked and
restored.
Indicates the
maximum output
power on the TX
NO NO Yes None
channel. The error
is precise to +/-0.5
DB.
Indicates the
maximum output
power of the RRU NO NO Yes None
or RFU TX unit
(single carrier).
Indicates the
maximum output
power of the RRU NO NO Yes None
or RFU TX unit
(multiple carriers).
Indicates the
maximum output
power supported by
the TX channel
hardware. This
NO NO Yes None
parameter value
can have a 0.5 dB
difference from the
actual maximum
output power.
Indicates the
minimum downlink
frequency
supported by the
RRU band 1. For
example, this
NO NO Yes None
parameter is set to
9650, the minimum
downlink frequency
of the RRU is 9650
x 0.1 MHz, which
equals to 965 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU band 1. For
example, if this
NO NO Yes None
parameter is set to
9850, the maximum
downlink frequency
of the RRU is 9850
x 0.1 MHz, which
equals to 985 MHz.
Indicates the
bandwidth
supported by each
TX channel band 1
NO NO Yes None
in the downlink.
This bandwidth is
an instantaneous
bandwidth.
Indicates the
minimum downlink
frequency
supported by the
RRU band 2. This
parameter is
NULL,when the
RRU does not
bands.For example,
this parameter is
set to 9650, the
minimum downlink
frequency of the
RRU is 9650 x 0.1
MHz, which equals
to 965 MHz.
Indicates the
maximum downlink
frequency
supported by the
RRU band 2. This
parameter is
NULL,when the
RRU does not
bands.For example,
set to 9850, the
maximum downlink
frequency of the
RRU is 9850 x 0.1
MHz, which equals
to 985 MHz.
Indicates the
bandwidth
supported by each
TX channel band 2
in the downlink.
This bandwidth is
NO NO Yes None
an instantaneous
bandwidth. This
parameter is NULL,
when the RRU
does not supported
multi-bands.
Indicates the
minimal test NO NO Yes None
frequency.
Indicates the
maximal test NO NO Yes None
frequency. .
of the cross feed NO NO Yes None
test.
Indicates the IPv4

address of the NTP YES NO No None
server.
performed
periodically. The
switch for periodic
NTP time
synchronization is
turned on
automatically.The
time of an eNodeB
may have
differences with the
standard time, and
a large difference
affects the accuracy
of KPIs. Therefore,
a period must be
configured for the
eNodeB to perform
time
synchronization NO YES No None
with the NTP server
periodically to
ensure the accurate
time.
The period for
periodic NTP time
synchronization
must be configured
based on the NTP
server performance,
transport network
quality, and eNodeB
quantity.
A smaller period for
periodic NTP time
synchronization
leads to higher
loads for the NTP
Indicates the port
number of the NTP NO NO No None
server.
Indicates the mode

of the IP address of YES NO No None
the NTP server.
Indicates the IPv6

address of the NTP YES NO No None
server.
Indicates the mode

of the NTP NO NO No None
authentication.
each byte are used
to construct 56-bit
key data, and the
eighth bit is the odd
parity bit for each
byte. Any empty bit
is filled with 0 to
ensure that the key
data is composed
of 16 hexadecimal
digits and has an
odd number for
parity check. The
key used in the
DES_N algorithm is
similar to the key
used in the DES_S
algorithm. The only
difference is that in
NO YES No None
the key used in the
DES_N algorithm,
the most significant
bit is used for parity
check of each byte.
The key used in the
DES_A algorithm is
an ASCII string of
one to eight
characters. The
seven least
significant digits of
the ASCII value
corresponding to
each character are
used to construct
56-bit key data. For
any ASCII string of
less than eight
Indicates the
server-side index of
the NTP
authentication key.
NO YES No None
The index must be
the same as the
setting on the
server.
Indicates an NTP
server is an active
or standby server.
Users can run the
SET NO NO No None
MASTERNTPS
command to set an
NTP server as a
master NTP server.
Indicates the time
NO NO No None
zone of the NE.
Indicates whether
NO NO No None
DST is enabled.
Indicates the mode
in which the DST
start date is
specified. There are
three modes:
Date, for example,
April 1;
Day of the week, for
example, the first
Sunday in April;
NO NO No None
Date plus day of the
week, for example,
April 1 and Sunday.
If it is Sunday on
April 1, DST starts
on April 1.
Otherwise, DST
starts on the first
Sunday after April
1.
Indicates the month

in which the NE NO NO No None
DST starts.
Indicates the day

on which the NE NO NO No None
DST starts.
Indicates in which
week the NE DST NO NO No None
starts.
Indicates the week

DST starts.
Indicates the time

when the NE DST
starts. The value of
NO NO No None
this parameter
observes the
standard time.
Indicates the end

date mode of the
NE DST. There are
three formats:
date format, for
example, April 1st;
week format, for
example, the first
Sunday in April;
date and week NO NO No None
format, for example,
for example, April
1st and Sunday. If it
is Sunday on April
1st, April 1st is the
date. Otherwise,
the first Sunday
after April 1st is the
date.
Indicates the month

DST ends.
Indicates the day
on which the NE NO NO No None
DST ends.
Indicates the week

NO NO No None
in which DST ends.
Indicates the week

DST ends.
Indicates the time

when the DST of
the NE ends. The
NO NO No None
value of this
parameter observes
DST.
Indicates the DST
time offset of the
NE. This parameter
can be set to a
negative value. A
negative value
indicates that the NO NO No None
NE time is earlier
than the DST time,
and a positive value
indicates that the
NE time is later
than the DST time.
of time zone. This
parameter can be NO NO No None
set to a negative
value.
Indicates the date
to be set for the NE.
The format is as
follows: YYYY-MM-
DD. For example, NO NO Yes None
2006-09-08
indicates
September 8th of
2006.
Indicates the time
to be set for the NE.
The format is as
NO NO Yes None
follows: HH:MM:SS.
For example,
10:20:05.
Indicates the
current date and
time of the NE. The
query result is the
local time of the
NE, including the
year, month, day,
hour, minute,
second, and time
zone. If the DST of NO NO Yes None
the NE is effective,
the query result
contains a DST flag
(the flog used to
indicate whether
the DST is applied).
The format is as
follows: YYYY-MM-
DD HH:MM:SS.
Indicates the
external reference
NO NO No None
time source of the
NE.
Indicates the date

and time of the last
successfully-
synchronized time
NO NO Yes None
of the NE. The
format is as follows:
YYYY-MM-DD
HH:MM:SS.
Indicates the
encryption mode of
transmitted data. If
Transport
Encrypted Mode is
set to AUTO, the
FTP client performs
file transfer in the
form of ciphertext
first and then, if
failed, in the form of
plaintext.
If the FTP server
supports the cipher
text and the NO NO No None
encryption fails due
to the fault of a
transmission device
such as a security
gateway, the FTP
connection fails to
be set up because
the FTP client does
not attempt to set
up the FTP
connection again in
plain text mode
automatically in this
case.
Indicates whether
FTP connections in
encrypted mode
can be established
when there is a
state firewall. In
plain-text mode,
this parameter is
invalid. In encrypted
mode, if this
parameter is set to
YES(Yes), the FTP
client will send the
CCC command to
change the FTP
control connection
to plain-text mode
so that the state
firewall can identify
NO NO No None
and dynamically
open the port
required by the FTP
data connection; if
this parameter is
set to NO(No), the
FTP data
connection may not
established due to
the restrictions of
the state firewall on
the port used by the
FTP data
connection. It is
recommended that
this parameter be
set to YES(Yes)
with security
requirements met.
Indicates whether
the certificate
authentication
mode is supported NO NO No None
when encrypted
data is being
transmitted.
Indicates the IP
address of the FTP YES NO No None
server.
Indicates the port of

NO NO No None
the FTP server.
Indicates the index
YES YES No None
of the operator.
Indicates the
extended QoS
Class Identifier
(QCI), which is YES YES No None
required by the
operator for user
differentiation.
Indicates the ID of a LOFD-001043 /

service-based inter- TDLOFD-001043
NO NO No
RAT handover LOFD-001046 /
policy group. TDLOFD-001046
Indicates the ID of
the service-based
inter-frequency NO NO No LBFD-00201805
handover policy
group.
Indicates the index

YES YES No None
of the operator.
Indicates the QoS
Class Identifier
(QCI) of an EPS
bearer. Different
QCIs represent
different QoS
specifications such
as the packet delay
budget, packet YES YES No None
error loss rate, and
resource type
(whether the
service is a GBR
service or not). For
details, see Table
6.1.7 in 3GPP TS
23.203.

service-based inter- TDLOFD-001043
NO NO No
RAT handover LOFD-001046 /
Indicates the ID of
the service-based
handover policy
group.
Indicates the index

YES YES No None
of the operator.
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021 /
TDLOFD-001021
LOFD-001044 /
TDLOFD-001044
Ndicates the high-
LOFD-001045 /
priority system to be
TDLOFD-001045
considered in blind
LOFD-001033 /
handovers. It is
TDLOFD-001033
UTRAN by default. NO NO No
LOFD-001034 /
This parameter can
TDLOFD-001034
be set to UTRAN,
LOFD-001035 /
GERAN, or
TDLOFD-001035
CDMA2000.
LOFD-001068 /
TDLOFD-001068
LOFD-001069 /
TDLOFD-001069
LOFD-001052 /
TDLOFD-001052
LOFD-001053 /
TDLOFD-001053
LOFD-001019 /
TDLOFD-001019
medium-priority TDLOFD-001020
system to be LOFD-001021 /
considered in blind TDLOFD-001021
handovers. It is LOFD-001044 /
GERAN by default. TDLOFD-001044
This parameter can LOFD-001045 /
be set to UTRAN, TDLOFD-001045
GERAN, or LOFD-001033 /
CDMA2000. If this TDLOFD-001033
NO NO No
parameter is set to LOFD-001034 /
NULL, the system TDLOFD-001034
with the medium LOFD-001035 /
blind handover TDLOFD-001035
priority is not LOFD-001068 /
specified and only TDLOFD-001068
blind handovers to LOFD-001069 /
the high-priority TDLOFD-001069
system are LOFD-001052 /
applicable. TDLOFD-001052
LOFD-001053 /
TDLOFD-001053
LOFD-001019 /
TDLOFD-001019
Indicates the low-
LOFD-001020 /
priority system to be
TDLOFD-001020
considered in blind
LOFD-001021 /
handovers. It is
TDLOFD-001021
CDMA2000 by
LOFD-001044 /
default. This
TDLOFD-001044
parameter can be
LOFD-001045 /
set to UTRAN,
TDLOFD-001045
GERAN, or
LOFD-001033 /
CDMA2000. If this
TDLOFD-001033
LOFD-001034 /
NULL, the system
TDLOFD-001034
with the medium
LOFD-001035 /
blind handover
TDLOFD-001035
priority is not
LOFD-001068 /
specified and only
TDLOFD-001068
blind handovers to
LOFD-001069 /
the high- and
TDLOFD-001069
medium-priority
LOFD-001052 /
systems are
TDLOFD-001052
applicable.
LOFD-001053 /
TDLOFD-001053
Indicates the
Location Services
(LCS) capability of
the UTRAN. If this
LOFD-001033 /
parameter is set to
TDLOFD-001033
ON, the UTRAN NO NO No
LOFD-001047 /
supports LCS. If
TDLOFD-001047
this parameter is
set to OFF, the
UTRAN does not
support LCS.
Indicates the
Location Services
(LCS) capability of
the GERAN. If this
LOFD-001034 /
parameter is set to
TDLOFD-001034
ON, the GERAN NO NO No
LOFD-001047 /
supports LCS. If
TDLOFD-001047
this parameter is
set to OFF, the
GERAN does not
support LCS.
Indicates the
Location Services
(LCS) capability of
the CDMA2000. If
this parameter is
LOFD-001035
set to ON, the
NO NO No LOFD-001047 /
CDMA2000
TDLOFD-001047
supports LCS. If
this parameter is
set to OFF, the
CDMA20000 does
not support LCS.
Indicates the index

YES YES No None
of the operator.
LBFD-00201801 /
TDLBFD-00201801
LBFD-00201802 /
TDLBFD-00201802
LBFD-00201804 /
TDLBFD-00201804
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021 /
TDLOFD-001021
LOFD-001032 /
Indicates the mobile
TDLOFD-001032
country code of the YES YES No
LOFD-001044 /
target PLMN.
TDLOFD-001044
LOFD-001045 /
TDLOFD-001045
LOFD-001043 /
TDLOFD-001043
LOFD-001046 /
TDLOFD-001046
LOFD-001072 /
TDLOFD-001072
LOFD-001073 /
TDLOFD-001073
LBFD-00201805 /
TDLBFD-00201805
LBFD-00201801 /
TDLBFD-00201801
LBFD-00201802 /
TDLBFD-00201802
LBFD-00201804 /
TDLBFD-00201804
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021 /
TDLOFD-001021
LOFD-001032 /
TDLOFD-001032
network code of the YES YES No
LOFD-001044 /
target PLMN.
TDLOFD-001044
LOFD-001045 /
TDLOFD-001045
LOFD-001043 /
TDLOFD-001043
LOFD-001046 /
TDLOFD-001046
LOFD-001072 /
TDLOFD-001072
LOFD-001073 /
TDLOFD-001073
LBFD-00201805 /
TDLBFD-00201805
LOFD-001044 /
TDLOFD-001044
Indicates the ID of
LOFD-001045 /
the RAT/frequency YES YES No
TDLOFD-001045
priority group.
LOFD-001054
LOFD-00105401
LOFD-001044 /
TDLOFD-001044
Indicates the Radio
LOFD-001045 /
Access Technology YES YES No
TDLOFD-001045
(RAT).
LOFD-001054
LOFD-00105401
Indicates the
downlink EARFCN.
Before configuring
LOFD-001044 /
a priority for an
TDLOFD-001044
EARFCN specified
LOFD-001045 /
by this parameter, YES YES No
TDLOFD-001045
ensure that an
LOFD-001054
external or local cell
LOFD-00105401
working on this
EARFCN has been
configured.
Indicates the
LOFD-001044 /
priority of the RAT
TDLOFD-001044
or frequency. The NO NO No
LOFD-001045 /
value 0 indicates
TDLOFD-001045
LOFD-001044 /
TDLOFD-001044
Indicates the
LOFD-001045 /
GERAN frequency NO NO No
TDLOFD-001045
band.
LOFD-001054
LOFD-00105401
Indicates the ID of
YES YES No LBFD-00201805
the operator.
Indicates the ID of
the service-based
inter-frequency YES YES No LBFD-00201805
handover policy
group.
Indicates whether
the policy group
allows a target
frequency to be
specified for
service-based inter-
frequency
handovers. The
value 0 indicates
that the policy NO NO No LBFD-00201805
group does not
allow a target
frequency to be
specified, and the
value 1 indicates
that the policy
group allows a
target frequency to
be specified.
Indicates the
frequency to which
a service with a
NO NO No LBFD-00201805
specified QCI is
preferentially
handed over.
LOFD-001043 /
Indicates the index TDLOFD-001043
YES YES No
of the operator. LOFD-001046 /
TDLOFD-001046
Indicates the ID of LOFD-001043 /

the service-based TDLOFD-001043
YES YES No
inter-RAT handover LOFD-001046 /
Indicates whether
inter-RAT handover LOFD-001043 /
is required, allowed, TDLOFD-001043
NO NO No
or not allowed for LOFD-001046 /
services with the TDLOFD-001046
QCI.
LOFD-001032 /
TDLOFD-001032
LOFD-001044 /
TDLOFD-001044
LOFD-001045 /
Indicates the
TDLOFD-001045
subscriber profile ID YES YES No
LOFD-001054 /
(SPID).
TDLOFD-001054
LOFD-00105401 /
TDLOFD-00105401
LOFD-001059 /
TDLOFD-001059
Indicates whether
DRX is supported.
set to TRUE,
ordinary DRX
LBFD-002017 /
parameters are
TDLBFD-002017
applied to UEs with NO NO No
LOFD-001054 /
the SPID. If this
TDLOFD-001054
parameter is set to
FALSE, special
DRX parameters
are applied to UEs
with the SPID.
Indicates whether
to specify a
RAT/frequency
priority group. If this LOFD-001032 /
parameter is set to TDLOFD-001032
CFG, UEs LOFD-001044 /
preferentially camp TDLOFD-001044
NO NO No
on the specified LOFD-001045 /
RAT/frequency. If TDLOFD-001045
this parameter is LOFD-001054 /
set to NOT_CFG, TDLOFD-001054
UEs randomly
camp on an
RAT/frequency.
LOFD-001032 /
TDLOFD-001032
LOFD-001044 /
TDLOFD-001044
LOFD-001045 /
Indicates the ID of a
TDLOFD-001045
RAT/frequency NO NO No
LOFD-001054 /
priority group.
TDLOFD-001054
LOFD-00105401 /
TDLOFD-00105401
LOFD-001059 /
TDLOFD-001059
Indicates whether
to support
preallocation. If this
parameter is set to
LOFD-001054 /
TRUE, resources
TDLOFD-001054
can be preallocated NO NO No
LOFD-001059 /
to UEs. If this
TDLOFD-001059
parameter is set to
FALSE, resources
are not preallocated
to UEs.
Indicates whether
to enable or disable
inter-frequency load
balancing for the
SPID. The values
LOFD-001032 /
TRUE and FALSE
TDLOFD-001032
indicate that inter- NO NO No
LOFD-001054 /
frequency load
TDLOFD-001054
balancing is
allowed and
prohibited for UEs
with the SPID,
respectively.
Indicates whether
inter-RAT load
balancing for the LOFD-001044 /
SPID. The values TDLOFD-001044
TRUE and FALSE LOFD-001045 /
NO NO No
indicate that inter- TDLOFD-001045
RAT load balancing LOFD-001054 /
is allowed and TDLOFD-001054
prohibited for UEs
with the SPID,
respectively.
Indicates whether
to enable
handovers back to
the home public
land mobile network
(HPLMN) for UEs
LBFD-00201802 /
with the SPID. If
TDLBFD-00201802
this function is
LOFD-001019 /
enabled, a roaming
TDLOFD-001019
UE can be handed NO NO No
LOFD-001022 /
over to the HPLMN
TDLOFD-001022
when this UE
LOFD-001054 /
moves back to the
TDLOFD-001054
HPLMN. If this
function is disabled,
this UE cannot be
handed over to the
HPLMN based on
the SPID.
of the counter
check timer. When
the timer expires, a
counter check
procedure is
initiated. After the
procedure is
LBFD-002004 /
complete, the timer NO NO No
TDLBFD-002004
is restarted. A
length of 0 indicates
that the timer is
invalid. In this case,
the eNodeB cannot
initiate periodic
counter check
procedures.
Indicates the
COUNT value for
initiating counter
check procedures.
When the COUNT
value (used at the
PDCP layer) of any
DRB for a UE is a
multiple of the value
of this parameter, LBFD-002004 /
NO NO No
the eNodeB TDLBFD-002004
initiates a counter
check procedure.
The value 0
indicates that the
eNodeB does not
initiate a counter
check procedure
based on the
COUNT value.
Indicates whether
to release a DRB
when the counter LBFD-002004 /
NO NO No
check detects an TDLBFD-002004
unexpected result
in the DRB.
Indicates the
highest-priority
ciphering algorithm LOFD-00101001 /
NO NO No
eNodeB. The value LOFD-00101002 /
NULL indicates that TDLOFD-00101002
ciphering is not
applied.
Indicates the
second-priority
ciphering algorithm LOFD-00101001 /
NO NO No
eNodeB. The value LOFD-00101002 /
NULL indicates that TDLOFD-00101002
ciphering is not
applied.
Indicates the third-

priority ciphering
algorithm supported LOFD-00101001 /
by the eNodeB. The TDLOFD-00101001
NO NO No
value NULL LOFD-00101002 /
indicates that TDLOFD-00101002
ciphering is not
applied.
Indicates the timer
governing the
period the eNodeB
will NO NO No None
wait for a response
message from the
MME.
Indicates the timer
governing the
period the eNodeB
will
NO NO No None
wait for a response
message from the
neighboring
eNodeB.
Indicates the timer
governing the
period the eNodeB
will NO NO No None
wait for a response
message from the
UE.
Indicates the
highest-priority
integrity protection
algorithm supported
LBFD-002004 /
by the eNodeB. The NO NO No
TDLBFD-002004
value NULL
indicates that
is not applied.
Indicates the
second-priority
algorithm supported
LBFD-002004 /
by the eNodeB. The NO NO No
TDLBFD-002004
value NULL
indicates that
is not applied.
Indicates the third-
priority integrity
protection algorithm
supported by the LBFD-002004 /
NO NO No
eNodeB. The value TDLBFD-002004
NULL indicates that
is not applied.
LBFD-002018 /
TDLBFD-002018
Indicates whether
LBFD-00201801 /
to enable or disable NO NO No
TDLBFD-00201801
X2 setup by SON.
LBFD-00201802 /
TDLBFD-00201802
Indicates the
method of X2 setup
by SON, that is, the
method of
automatically
LBFD-002018 /
setting up X2
TDLBFD-002018
interfaces. The
LBFD-00201801 /
value NO NO No
TDLBFD-00201801
X2_OVER_M2000
LBFD-00201802 /
can be set only for
TDLBFD-00201802
Huawei eNodeBs,
and the value
X2_OVER_S1 can
be set for any
eNodeB.
Indicates whether
scheduling request
indication (SRI)
adaptation. If this
parameter is set to
LBFD-002025 /
ON, the SRI period
TDLBFD-002025
adaptively changes
LOFD-001015 /
based on the SRI NO NO No
TDLOFD-001015
algorithm. If this
LBFD-002003 /
parameter is set to
TDLBFD-002003
OFF, the SRI period
is the value of the
SriPeriod parameter
in the
CellStandardQci
MO.
Indicates whether
to set a logical
channel group
profile.
Currently, two
logical channel
group profiles are
available:
LCG_PROFILE_0
and
LCG_PROFILE_1.
If LCG_PROFILE_0
LBFD-002025 /
is used, only one
TDLBFD-002025
logical channel NO NO No
LOFD-001015 /
group is assigned
TDLOFD-001015
to non-GBR
services. If
LCG_PROFILE_1
is used, two logical
channel groups are
assigned to non-
GBR services: one
to high-priority non-
GBR services and
the other to low-
priority non-GBR
services.
Indicates whether
RAN information
management (RIM)
for handovers in
RNC pool
scenarios. An RNC LOFD-001019 /
NO NO No
pool can be used TDLOFD-001019
for load balancing
between RNCs. A
cell under an RNC
can be controlled
by another RNC in
the RNC pool.
Indicates whether
an eNodeB uses
serial or parallel
message
transmission mode
during security
mode activation
and RRC
reconfiguration LBFD-002007 /
NO NO No
procedures. If this TDLBFD-002007
parameter is set to
ON, the eNodeB
uses parallel
transmission mode.
set to OFF, the
eNodeB uses serial
transmission mode.
Indicates whether
the eNodeB
automatically
updates the
configuration of
neighboring cells
based on the
messages received
over the X2
interface. The
messages include
X2 SETUP
REQUEST, X2
SETUP
RESPONSE, and
ENB
CONFIGURATION NO NO No None
UPDATE.Before the
eNodeB
configuration data
is modified by using
the CME, it is
recommended that
this switch be
turned off to disable
the automatic
update. If this
the configuration
data may be lost or
become abnormal
during the
automatic update.
Indicates whether
to enable ROHC.
Set this parameter
to ON if the LOFD-001017 /
NO NO No
eNodeB is TDLOFD-001017
expected to support
VoIP or video
services.
decompressor, and
a feedback channel
is not mandatory.
Therefore, U-Mode
is less reliable than
Bidirectional
Optimistic Mode (O-
Mode) and
Bidirectional
Reliable Mode (R-
Mode), but its
feedback-induced
overhead is
minimum compared
with the overhead
in O-Mode and R-
Mode. In O-Mode,
the decompressor
LOFD-001017 /
can send feedback NO NO No
TDLOFD-001017
messages to the
compressor to
indicate
decompression
failures or
successful context
updates. O-Mode is
more reliable than
U-Mode and
requires a smaller
amount of feedback
than R-Mode. In R-
Mode, the reliability
of context
synchronization
between the
compressor and the
decompressor is
supported by the
eNodeB.
Under the ROHC
framework, header
compression
algorithms vary with
protocols. Profiles
define the header
compression
protocols (such as
RTP/UDP/IP or
TCP/IP), which are
under the same
ROHC framework,
for specific types of
packet streams.
Each profile has a
unique identifier.
As defined by LTE LOFD-001017 /
NO NO No
specifications, the TDLOFD-001017
eNodeB supports
the following
profiles: profile
0x0001 (usage:
RTP/UDP/IP;
reference: RFC
3095 and RFC
4815), profile
0x0002 (usage:
UDP/IP; reference:
RFC 3095 and RFC
4815), profile
0x0003 (usage:
ESP/IP; reference:
RFC 3095 and RFC
4815), and profile
0x0004 (usage: IP;
reference: RFC
of timer T302.
T302 specifies the
wait time for
retransmitting an
RRCConnectionRe
quest message
after the previous
request with a
cause other than
"MO-Data" and
"MO-Signalling" is LBFD-002007 /
NO NO No
rejected. TDLBFD-002007
This timer is started
after the UE
receives the
RRCConnectionRej
ect message.
This timer is
stopped when the
UE enters the
RRC_CONNECTE
D mode or performs
cell reselection.

of timer T320 for
load balancing.
T320 specifies the
time period during
which the dedicated
priorities (used for
cell reselection)
retain valid. The
time period is
contained in the
RRCConnectionRel
ease message that
is received by the LBFD-002018 /
UE. After T320 TDLBFD-002018
NO NO No
expires, the LBFD-00201803 /
dedicated priorities TDLBFD-00201803
become invalid.
when the UE
receives an
RRCConnectionRel
ease message
containing the t320
IE.
This timer is
stopped when the
UE enters the
RRC_CONNECTE
D mode.
of timer T304 for
intra-RAT handover.
If the UE does not
complete the LBFD-002018 /
handover before TDLBFD-002018
this timer expires, LBFD-00201803 /
NO NO No
the UE reverts back TDLBFD-00201803
to the associated LBFD-002007 /
configuration and TDLBFD-002007
initiates an RRC
connection
reestablishment
procedure.

of timer T304 for
inter-RAT handover
to GERAN. If the
UE does not
complete the
LBFD-002018 /
handover before
TDLBFD-002018
this timer expires, NO NO No
LBFD-00201803 /
the UE reverts back
TDLBFD-00201803
to the associated
configuration and
initiates an RRC
connection re-
establishment
procedure.
of timer T320 to be
contained in
RRCConnectionRel
ease messages
sent for reasons
other than load
balancing. T320
specifies the time
period during which
the dedicated
priorities (used for
cell reselection) are
valid. After T320
expires, the
LBFD-002018 /
dedicated priorities
TDLBFD-002018
become invalid. NO NO No
LBFD-00201803 /
This parameter is
TDLBFD-00201803
invalid for UEs to
be redirected based
on the subscriber
profile ID (SPID).
when the UE
receives an
RRCConnectionRel
ease message
containing the t320
IE. It is stopped
when the UE enters
the
RRC_CONNECTE
D mode.
of the UE inactivity
timer. The eNodeB
monitors whether
UEs are receiving
or sending data.
When a UE has
neither received nor
sent data for a LBFD-002007 /
NO NO No
duration exceeding TDLBFD-002007
this period of time,
the eNodeB
releases the radio
resources for the
UE. If this
parameter is set to
0, the UE inactivity
timer is not used.
Indicates the timer
used to govern the
period in which the
eNodeB maintains
uplink
synchronization for
a UE. After this
timer expires, the
eNodeB does not
send Timing
Advance Command
to the UE. If this LBFD-002007 /
NO NO No
parameter is set to TDLBFD-002007
0, this parameter
does not take effect
and, as a result, the
eNodeB will
constantly send
Timing Advance
Command to the
UE to maintain
uplink
synchronization for
the UE.
Indicates the ID of
YES YES No None
the TCE for MDT.
Indicates the IP
address version.
IPv4(IPv4 Address)
indicates that the
NO NO No None
version is IPv4.
IPv6(IPv6 Address)
indicates that the
version is IPv6.
Indicates the IPv4

NO NO No None
address of the TCE.
Indicates the IPv6
NO NO No None
address of the TCE.
Indicates the local

identity of the cell. It
cell within an
eNodeB.
Indicates the QoS

class identifier
(QCI) of an evolved
packet system
(EPS) bearer.
Different QCIs
represent different
QoS specifications
such as the packet
YES YES No None
delay budget,
packet error loss
rate, and resource
type (whether the
service is a GBR
details, see Table
6.1.7 in 3GPP TS
23.203.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
will be replaced with
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
patch versions and NO NO No None
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 10 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates the index

YES YES No None
of the operator.
Indicates the QoS

class identifier
(QCI) of an evolved
packet system
(EPS) bearer.
Different QCIs
represent different
QoS specifications
such as the packet
YES YES No None
delay budget,
packet error loss
rate, and resource
type (whether the
service is a GBR
details, see Table
6.1.7 in 3GPP TS
23.203.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates the index

YES YES No None
of the operator.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates the QoS

class identifier
(QCI) of an evolved
packet system
(EPS) bearer.
Different QCIs
represent different
QoS specifications
such as the packet
YES YES No None
delay budget,
packet error loss
rate, and resource
type (whether the
service is a GBR
details, see Table
6.1.7 in 3GPP TS
23.203.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates the local

ID of the cell. It
YES YES No None
uniquely identifies a
cell within a BS.

for adjusting the PA
through power
control on the
PDSCH. If this
parameter is set to LBFD-002016 /
NO NO No
ON, the PA is TDLBFD-002016
adjusted
dynamically when
the channel quality
is extremely good
or bad.
Indicates the PA to
be used when PA
adjustment for
PDSCH power
control is disabled, LBFD-002016 /
NO NO No
downlink ICIC is TDLBFD-002016
disabled, and the
even power
distribution is used
for the PDSCH.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
threshold for UEs to
enter DRX in the
cell that operates in
FDD mode. This
threshold is used in
the DRX algorithm.
It is expressed as a
proportion of the
transmission time
LBFD-002017 /
intervals (TTIs) with NO NO No
TDLBFD-002017
data transmission
to the total TTIs. If
the traffic volume at
a UE is equal to or
lower than this
threshold, the
eNodeB decides
that the UE should
retain its DRX state
or enter DRX.
Indicates the
exit DRX in the cell
that operates in
FDD mode. This
the DRX algorithm.
proportion of the
transmission time
intervals (TTIs) with
data transmission
to the total TTIs. If
LBFD-002017 /
the traffic volume at NO NO No
TDLBFD-002017
a UE is equal to or
higher than this
threshold, the
eNodeB decides
that the UE should
retain its non-DRX
state or exit DRX.If
this parameter is
set to 1000, UEs
will not exit the DRX
mode after they
enter the DRX
mode.
traffic volume
enter DRX in the
cell that operates in
TDD mode. This
the DRX algorithm.
proportion of the
transmission time
LBFD-002017 /
TDLBFD-002017
uplink data
transmission to the
total TTIs. If the
traffic volume at a
UE is equal to or
lower than this
threshold, the
eNodeB decides
that the UE should
or enter DRX.

traffic volume
exit DRX in the cell
that operates in
TDD mode. This
the DRX algorithm.
proportion of the
transmission time
LBFD-002017 /
TDLBFD-002017
uplink data
transmission to the
total TTIs. If the
traffic volume at a
UE is equal to or
higher than this
threshold, the
eNodeB decides
that the UE should
retain its non-DRX
state or exit DRX.
Indicates the
downlink traffic
volume threshold
for UEs to enter
DRX in the cell that
operates in TDD
mode. This
the DRX algorithm.
proportion of the
transmission time LBFD-002017 /
NO NO No
intervals (TTIs) with TDLBFD-002017
downlink data
transmission to the
total TTIs. If the
traffic volume at a
UE is equal to or
lower than this
threshold, the
eNodeB decides
that the UE should
or enter DRX.
Indicates the
downlink traffic
volume threshold
for UEs to exit DRX
in the cell that
operates in TDD
mode. This
the DRX algorithm.
proportion of the
transmission time LBFD-002017 /
NO NO No
intervals (TTIs) with TDLBFD-002017
downlink data
transmission to the
total TTIs. If the
traffic volume at a
UE is equal to or
higher than this
threshold, the
eNodeB decides
that the UE should
retain its non-DRX
state or exit DRX.
of the UE traffic
measurement
period. The traffic
volume of a UE
during this period is
measured. Based LBFD-002017 /
NO NO No
on the TDLBFD-002017
measurement
result, the DRX
algorithm decides
whether the UE
should enter or exit
DRX.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
Indicates whether
the transmit power
of the UE is
adjusted according
to the difference
between MCSs.
indication is
contained in an
RRC message
signaled to the UE.
In the message,this
indication occupies LBFD-002026 /
NO NO No
one bit. The value TDLBFD-002026
0, which means
disabled, indicates
that TF is equal to
0 because Ks is
equal to 0. The
value 1, which
means enabled,
indicates that TF
is calculated on the
condition that Ks is
equal to 1.25.
Indicates the power
offset of the
sounding reference
signal to the LBFD-002026 /
NO NO No
PUSCH when TDLBFD-002026
DeltaMcsEnabled is
set to
UU_DISABLE.
Indicates the power

offset of the
sounding reference
signal to the LBFD-002026 /
NO NO No
PUSCH when TDLBFD-002026
DeltaMcsEnabled is
set to
UU_ENABLE.
Indicates the alpha
filtering coefficient
used by the UE
LBFD-002026 /
during RSRP NO NO No
TDLBFD-002026
measurement for
path loss
estimation.
Indicates the local

cell within an
eNodeB.
Indicates the
measurement
LOFD-001072 /
object type for
TDLOFD-001072
distance-based
LOFD-001073 /
handovers. The NO NO No
TDLOFD-001073
measurement
LBFD-00201804 /
object type can be
TDLBFD-00201804
E-UTRAN, GERAN,
or UTRAN.
Indicates the
threshold for
distance-based
handovers. If the LBFD-00201804 /
distance between a TDLBFD-00201804
UE and the cell LOFD-001072 /
NO NO No
center is greater TDLOFD-001072
than this threshold, LOFD-001073 /
a distance-based TDLOFD-001073
handover is
triggered for this
UE.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the ID of
the DRX parameter YES YES No None
group.
Indicates whether
bearers to which
the parameter
group applies
support DRX. The
value ON indicates
that the bearers
support DRX. The LBFD-002017 /
NO NO No
value OFF indicates TDLBFD-002017
that the bearers do
not support DRX. A
UE can enter the
DRX mode only
when all bearers
running on it
support DRX.
of the On Duration
Timer. Due to the
impact of CQI
reporting intervals
and SRS
transmission LBFD-002017 /
NO NO No
intervals, there is a TDLBFD-002017
possibility that the
actual value of this
parameter assigned
to a UE is larger
than the configured
value.
LBFD-002017 /
of the DRX NO NO No
TDLBFD-002017
Inactivity Timer.
Indicates the length LBFD-002017 /

of the DRX TDLBFD-002017
NO NO No
Retransmission LBFD-002005 /
Timer. TDLBFD-002005
Due to the
constraints of the
SRS bandwidth and
the
TimeAlignmentTime
r parameter (TA
period), the actual
value of this
parameter assigned
to a UE may be
less than the LBFD-002017 /
NO NO No
configured value. If TDLBFD-002017
you hope that the
value actually
assigned to a UE is
equal to or greater
than 80 ms, set the
TimeAlignmentTime
r parameter to a
value equal to or
greater than 2560
ms.
Indicates whether
LBFD-002017 /
short DRX cycles NO NO No
TDLBFD-002017
are enabled.
LBFD-002017 /
of a short DRX NO NO No
TDLBFD-002017
cycle.

of the DRX Short
Cycle Timer. If this
parameter is set to
1, the length of this
timer is one short
DRX cycle. If this
parameter is set to
2, the length of this
timer is two short LBFD-002017 /
NO NO No
DRX cycles. If this TDLBFD-002017
parameter is set to
a large value, a UE
for which short DRX
cycles are enabled
stays in short-cycle
DRX for a long
time. For details,
see 3GPP TS
36.321 5.7.
LOFD-001019 /
Indicates the local
TDLOFD-001019
ID of the cell. It
YES YES No LOFD-001020 /
TDLOFD-001020
cell within a BS.
LOFD-001021

the common TDLOFD-001019
parameter group YES YES No LOFD-001020 /
related to inter-RAT TDLOFD-001020
handover. LOFD-001021
Indicates the
hysteresis for inter-
RAT measurement
events A1 and A2.
This parameter is
used to prevent
frequent triggering
LOFD-001019 /
of event evaluation
TDLOFD-001019
caused by radio
signal fluctuation. In
TDLOFD-001020
this way, the
LOFD-001021
probability of ping-
pong handovers or
handover decision
errors is reduced. A
larger value of this
parameter results in
a lower probability.
Indicates the time-
to-trigger for inter-
RAT measurement
event A1 or A2.
When detecting that
the signal quality in
the serving cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately.
Instead, the UE
sends a report only LOFD-001019 /
when the signal TDLOFD-001019
quality continuously NO NO No LOFD-001020 /
meets the entering TDLOFD-001020
condition during the LOFD-001021
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers, and the
number of wrong
handovers. In
summary, it helps
prevent
unnecessary
handovers.
Indicates the RSRP

threshold for inter-
RAT measurement
event A1.
When the
measured RSRP
value of the serving
cell exceeds this
threshold, an event LOFD-001019 /
A1 report will be TDLOFD-001019
sent. The value NO NO No LOFD-001020 /
-141 does not take TDLOFD-001020
effect and is LOFD-001021
reserved for
backward
compatibility. If this
parameter is set to
-141, the value -140
is used as the
threshold in
implementation.
Indicates the RSRQ
RAT measurement
event A1. LOFD-001019 /
When the TDLOFD-001019
measured RSRQ NO NO No LOFD-001020 /
value of the serving TDLOFD-001020
cell exceeds this LOFD-001021
threshold, an event
A1 report will be
sent.
Indicates the RSRP

RAT measurement
event A2.
When the
measured RSRP
value of the serving
cell is below this
threshold, an event LOFD-001019 /
A2 report will be TDLOFD-001019
sent. The value NO NO No LOFD-001020 /
-141 does not take TDLOFD-001020
effect and is LOFD-001021
reserved for
backward
parameter is set to
is used as the
threshold in
implementation.
Indicates the RSRQ

RAT measurement
event A2. LOFD-001019 /
measured RSRQ NO NO No LOFD-001020 /
value of the serving TDLOFD-001020
cell is below this LOFD-001021
threshold, an event
A2 report will be
sent.
of the A2 threshold
LOFD-001019 /
for inter-RAT blind
TDLOFD-001019
redirection against NO NO No
LOFD-001020 /
the A2 threshold for
TDLOFD-001020
inter-RAT
handovers.
Indicates the local

ID of the cell. It LBFD-001001 /
YES YES No
uniquely identifies a TDLBFD-001001
cell within a BS.
Indicates the ID of
the parameter
group related to
YES YES No LOFD-001021
inter-RAT handover
to CDMA2000
1xRTT.
Indicates the
hysteresis for event
B1 for inter-RAT
handover to
CDMA2000 1xRTT.
This parameter is
used to prevent
frequent triggering
of event evaluation
caused by radio
this way, the NO NO No LOFD-001021
pong handovers or
handover decision
a lower probability
of ping-pong
handovers or
handover decision
errors.
Indicates the pilot

strength threshold
for event B1 related
to coverage-based
inter-RAT handover
to CDMA2000
NO NO No LOFD-001021
1xRTT. When the
measurement value
exceeds this
threshold, a
measurement
report will be sent.
Indicates the time-
to-trigger for event
B1 related to inter-
RAT handover to
CDMA2000 1xRTT.
When detecting that
at least one
neighboring cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately.
Instead, the UE
sends a report only
when the signal
quality continuously
meets the entering
condition during the
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers and the
number of wrong
handovers,
preventing
unnecessary
handovers.
Indicates the pilot

strength threshold
to load- or service-
based inter-RAT
handover to
CDMA2000 1xRTT. NO NO No LOFD-001021
When the
measurement value
exceeds this
threshold, a
measurement
Indicates the local
ID of the cell. It
YES YES No LBFD-002007
cell within a BS.
Indicates the ID of
the parameter
group related to YES YES No LBFD-002007
RLF timer and
constants values.

of timer 301. For
details, see 3GPP
TS 36.331.
of timer 310. For
details, see 3GPP
TS 36.331.

of timer 311. For
details, see 3GPP
TS 36.331.
Indicates the
maximum number
of successive "out NO NO No LBFD-002007
of sync" indications
received from L1.
Indicates the
maximum number
of successive "in NO NO No LBFD-002007
sync" indications
received from L1.
Indicates the
extended QoS
LOFD-001015 /
Class Identifier
TDLOFD-001015
(QCI), which is YES YES No
LOFD-00101502 /
required by the
TDLOFD-00101502
operator for service
differentiation.
Indicates the local

YES YES No
cell within a BS.
parameter group
LBFD-00201802 /
related to inter- NO NO No
TDLBFD-00201802
frequency
handover.
parameter group
related to inter-RAT NO NO No LOFD-001021
handover to
CDMA2000 1xRTT.
parameter group
handover to
CDMA2000 HRPD.
group of common TDLOFD-001019
parameters related NO NO No LOFD-001020 /
to inter-RAT TDLOFD-001020
handover. LOFD-001021
parameter group
LOFD-001020 /
related to inter-RAT NO NO No
TDLOFD-001020
handover to
GERAN.
parameter group
LOFD-001019 /
TDLOFD-001019
handover to
UTRAN.
parameter group
LBFD-00201801 /
related to intra- NO NO No
TDLBFD-00201801
frequency
handover.
LBFD-002017 /
DRX parameter NO NO No
TDLBFD-002017
group.
Indicates whether
to config the
parameters related NO NO No LBFD-002007
to RLF timer and
constants values.
Indicates the ID of
the parameter
group related to NO NO No LBFD-002007
RLF timer and
constants values.
Indicates the local

YES YES No
cell within a BS.
Indicates the QoS

class identifier
(QCI) of an evolved
packet system
(EPS) bearer.
Different QCIs
LOFD-001015 /
indicate different
TDLOFD-001015
QoS requirements, YES YES No
LOFD-00101502 /
such as the packet
TDLOFD-00101502
delay budget,
packet error loss
rate, and resource
type. For details,
see Table 6.1.7 in
3GPP TS 23.203.
parameter group
LBFD-00201802 /
related to inter- NO NO No
TDLBFD-00201802
frequency
handovers.
parameter group
handover to
CDMA2000 1xRTT.
parameter group
handover to
CDMA2000 HRPD.
LOFD-001019 /
TDLOFD-001019
common parameter
group related to
TDLOFD-001020
inter-RAT handover.
LOFD-001021
parameter group
LOFD-001020 /
TDLOFD-001020
handover to
GERAN.
parameter group
LOFD-001019 /
TDLOFD-001019
handover to
UTRAN.
parameter group
LBFD-00201801 /
related to intra- NO NO No
TDLBFD-00201801
frequency
handover.
LBFD-002017 /
DRX parameter NO NO No
TDLBFD-002017
group.
LBFD-002025 /
Indicates the TDLBFD-002025
interval at which LOFD-001015 /
NO NO No
scheduling request TDLOFD-001015
indicators are sent. LBFD-002003 /
TDLBFD-002003
Indicates whether
to config the
parameters related NO NO No LBFD-002007
to RLF timer and
constants values.
Indicates the ID of
the parameter
group related to NO NO No LBFD-002007
RLF timer and
constants values.
Indicates the local

YES YES No
cell within a BS.
Indicates the ID of
the parameter
group related to
inter-RAT handover
to CDMA2000
HRPD.
Indicates the
RAT handover to
CDMA2000 HRPD.
This parameter is
used to prevent
frequent triggering
of event evaluation
caused by radio
this way, the NO NO No LOFD-001021
pong handovers or
handover decision
a lower probability
of ping-pong
handovers or
handover decision
errors.
Indicates the pilot

strength threshold
based inter-RAT
handover to
CDMA2000 HRPD. NO NO No LOFD-001021
When the
measurement value
exceeds this
threshold, a
measurement
Indicates the time-
RAT handover to
CDMA2000 HRPD.
When detecting that
at least one
neighboring cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately.
Instead, the UE
sends a report only
when the signal
meets the entering
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers and the
number of wrong
handovers,
preventing
unnecessary
handovers.
Indicates the pilot

strength threshold
based inter-RAT
handover to LOFD-001021
CDMA2000 HRPD. NO NO No LOFD-001032 /
measurement value
exceeds this
threshold, a
measurement
Indicates the local
YES YES No
cell within a BS.
Indicates the ID of
LOFD-001020 /
the parameter
TDLOFD-001020
group related to YES YES No
LOFD-001023 /
inter-RAT handover
TDLOFD-001023
to GERAN.
Indicates the
RAT handover to
GERAN. This
parameter is used
to prevent frequent
triggering of event
evaluation caused
LOFD-001020 /
by radio signal
TDLOFD-001020
fluctuation. In this
LOFD-001023 /
way, the probability NO NO No
TDLOFD-001023
of ping-pong
LOFD-001046 /
handovers or
TDLOFD-001046
handover decision
a lower probability
of ping-pong
handovers or
handover decision
errors.
Indicates the RSSI

threshold for event
B1 related to
coverage-based
inter-RAT handover
to GERAN.
A UE sends a
measurement
LOFD-001020 /
report related to
TDLOFD-001020
event B1 to the NO NO No
LOFD-001023 /
eNodeB when the
TDLOFD-001023
RSSI in at least one
GERAN cell
exceeds this
threshold and other
triggering
conditions are met.
For details, see
3GPP TS 36.331.
Indicates the time-
RAT handover to
GERAN. When
detecting that the
signal quality in at
least one
neighboring cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately. LOFD-001020 /
Instead, the UE TDLOFD-001020
NO NO No
quality continuously LOFD-001046 /
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers and the
number of wrong
handovers,
preventing
unnecessary
handovers.
Indicates the RSSI

threshold for event
B1 related to load-
or service-based LOFD-001020 /
inter-RAT handover TDLOFD-001020
to GERAN. LOFD-001032 /
NO NO No
measured RSSI LOFD-001046 /
value exceeds this TDLOFD-001046
threshold, a
measurement
Indicates the local
YES YES No
cell within a BS.
Indicates the ID of
LOFD-001019 /
the parameter
TDLOFD-001019
LOFD-001022 /
inter-RAT handover
TDLOFD-001022
to UTRAN.
Indicates the Ec/No
threshold for event
B1 related to
coverage-based
inter-RAT handover
to UTRAN.
This parameter
specifies the
requirement for
Ec/No of the target
UTRAN cell. For a
cell with large signal
fading variance, set
this parameter to a
large value to
prevent
unnecessary
handovers. For a LOFD-001019 /
cell with small TDLOFD-001019
NO NO No
signal fading LOFD-001022 /
variance, set this TDLOFD-001022
parameter to a
small value to
ensure timely
handovers. A large
value of this
a low probability of
handover to the
UTRAN cell, and a
small value leads to
a high probability.
When the
measurement value
exceeds this
threshold, a
measurement
Indicates the RSCP
threshold for event
B1 related to
coverage-based
inter-RAT handover
to UTRAN.
This parameter
LOFD-001019 /
specifies the
TDLOFD-001019
requirement for NO NO No
LOFD-001022 /
RSCP of the target
TDLOFD-001022
UTRAN cell.
When the
measurement value
exceeds this
threshold, a
measurement
Indicates the
RAT handover to
UTRAN. This
parameter is used
to prevent frequent
triggering of event
evaluation caused
LOFD-001019 /
by radio signal
TDLOFD-001019
fluctuation. In this
LOFD-001022 /
way, the probability NO NO No
TDLOFD-001022
of ping-pong
LOFD-001043 /
handovers or
TDLOFD-001043
handover decision
a lower probability
of ping-pong
handovers or
handover decision
errors.
Indicates the time-
RAT handover to
UTRAN. When
detecting that the
least one
neighboring cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately. LOFD-001019 /
Instead, the UE TDLOFD-001019
NO NO No
quality continuously LOFD-001043 /
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers and the
number of wrong
handovers,
preventing
unnecessary
handovers.
Indicates the Ec/No
threshold for event
B1 related to load-
or service-based
inter-RAT handover
to UTRAN.
This parameter
specifies the
requirement for
Ec/No of the target
UTRAN cell. When
the measurement
value exceeds this
LOFD-001019 /
threshold, a
TDLOFD-001019
measurement
LOFD-001032 /
report may be sent. NO NO No
TDLOFD-001032
For a cell with large
LOFD-001043 /
signal fading
TDLOFD-001043
variance, set this
parameter to a
large value to
prevent
unnecessary
handovers. For a
cell with small
signal fading
variance, set this
parameter to a
small value to
ensure timely
handovers.
Indicates the RSCP

threshold for event
B1 related to load-
or service-based
inter-RAT handover
to UTRAN.
LOFD-001019 /
This parameter
TDLOFD-001019
specifies the
LOFD-001032 /
requirement for NO NO No
TDLOFD-001032
RSCP of the target
LOFD-001043 /
UTRAN cell.
TDLOFD-001043
When the
measurement value
exceeds this
threshold, a
measurement
Indicates the local
YES YES No
cell within a BS.
Indicates the ID of
LBFD-00201801 /
the parameter
TDLBFD-00201801
LBFD-00201802 /
inter-frequency
TDLBFD-00201802
handover.
Indicates the
hysteresis for inter-
frequency
measurement
events A1 and A2.
This parameter is
used to prevent
frequent triggering
of event evaluation
LBFD-00201802 /
caused by radio NO NO No
TDLBFD-00201802
this way, the
pong handovers or
handover decision
Indicates the time-
to-trigger for inter-
frequency
measurement event
A1 or A2.
When detecting that
the serving cell
meets the triggering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately.
Instead, the UE
sends a report only
when the signal LBFD-00201802 /
NO NO No
quality continuously TDLBFD-00201802
meets the entering
time-to-trigger. This
parameter helps
decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers, and the
number of wrong
handovers. In
summary, it helps
prevent
unnecessary
handovers.
Indicates the RSRP

frequency
measurement event
A1.
When the
measured RSRP
value exceeds this
threshold, a
measurement
LBFD-00201802 /
report will be sent. NO NO No
TDLBFD-00201802
The value -141
and is reserved for
backward
parameter is set to
is used as the
threshold in
implementation.
Indicates the RSRQ
frequency
measurement event
A1.
LBFD-00201802 /
When the NO NO No
TDLBFD-00201802
measured RSRQ
value exceeds this
threshold, a
measurement
Indicates the RSRP

frequency
measurement event
A2.
When the
measured RSRP
value is below the
threshold, a
measurement
LBFD-00201802 /
report will be sent. NO NO No
TDLBFD-00201802
The value -141
and is reserved for
backward
parameter is set to
is used as the
threshold in
implementation.
Indicates the RSRQ
frequency
measurement event
A2.
LBFD-00201802 /
When the NO NO No
TDLBFD-00201802
measured RSRQ
value is below this
threshold, a
measurement
report may be sent.
Indicates the
A4. This parameter
is used to prevent
frequent triggering LBFD-00201802 /
of event evaluation TDLBFD-00201802
caused by radio LBFD-00201804 /
signal fluctuation. In TDLBFD-00201804
NO NO No
this way, the LOFD-001032 /
probability of ping- TDLOFD-001032
pong handovers or LBFD-00201805 /
handover decision TDLBFD-00201805
Indicates the RSRP
threshold for event
A4 related to
coverage-based
inter-frequency
handover. When
the measured
RSRP value
exceeds this
threshold, an inter-
LBFD-00201802 /
frequency
TDLBFD-00201802
measurement NO NO No
LBFD-00201804 /
TDLBFD-00201804
The value -141
and is reserved for
backward
parameter is set to
is used as the
threshold in
implementation.
Indicates the RSRQ

threshold for event
A4 related to
coverage-based
inter-frequency
LBFD-00201802 /
handover. When
TDLBFD-00201802
the measured NO NO No
LBFD-00201804 /
RSRQ value
TDLBFD-00201804
exceeds this
frequency
measurement
Indicates the time-
A4 for the inter-
frequency
handover. When
detecting that the
least one
neighboring cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
LBFD-00201802 /
immediately.
TDLBFD-00201802
Instead, the UE
LBFD-00201804 /
sends a report only
TDLBFD-00201804
when the signal NO NO No
LOFD-001032 /
TDLOFD-001032
meets the entering
LBFD-00201805 /
TDLBFD-00201805
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers, and the
number of wrong
handovers. In
summary, it helps
prevent
unnecessary
handovers.
Indicates the RSRP
threshold for event
A4 related to load-
or frequency-
priority-based inter-
frequency
handover. When
the measured
RSRP value
exceeds this
threshold, an inter- LOFD-001032 /
frequency TDLOFD-001032
NO NO No
measurement LBFD-00201805 /
report will be sent. TDLBFD-00201805
The value -141
and is reserved for
backward
parameter is set to
is used as the
threshold in
implementation.
Indicates the RSRQ

threshold for event
A4 related to load-
or frequency-
frequency LOFD-001032 /
handover. When TDLOFD-001032
NO NO No
the measured LBFD-00201805 /
RSRQ value TDLBFD-00201805
exceeds this
frequency
measurement
Indicates the RSRP
threshold for
frequency-priority-
based inter-
frequency
measurement event
A1.
When the
measured RSRP
value exceeds this
threshold, an event
A1 report will be NO NO No None
sent. The value
-141 does not take
effect, and is
reserved for
backward
parameter is set to
is used as the
threshold in
implementation.
Indicates the RSRQ

threshold for
frequency-priority-
based inter-
frequency
measurement event
A1. NO NO No None
When the
measured RSRQ
value exceeds this
threshold, an event
A1 report may be
sent.
for event A3
associated with
inter-frequency
handover. This
parameter
determines the
border between the
serving cell and the
neighboring cell. If
the parameter is set
to a large value, an
handover is
performed only
when the signal
quality of the
neighboring cell is
significantly better
than that of the
serving cell and
other triggering
conditions are met.
For details, see
3GPP TS 36.331.
Indicates the RSRP

threshold for event
A1 associated with
event-A3-triggered
inter-frequency
handover.
When the
measured RSRP
value exceeds this
threshold, a
measurement
Indicates the RSRP
threshold for event
A2 associated with
event-A3-triggered
inter-frequency
handover. When
the measured
RSRP value is
below the
threshold, a
measurement
Indicates the RSRP

threshold for
frequency-priority-
based inter-
frequency
measurement event
NO NO No None
A2.
If the measured
RSRP value is less
than this threshold,
an event A2 report
will be sent.
Indicates the RSRQ

frequency
measurement event
A2.
When the NO NO No None
measured RSRQ
value is below this
threshold, a
measurement
Indicates the local

YES YES No
cell within a BS.
Indicates the ID of
LBFD-00201801 /
the parameter
TDLBFD-00201801
LBFD-00201802 /
intra-frequency
TDLBFD-00201802
handover.
Indicates the
A3 associated with
intra-frequency
handover. This
parameter prevents
frequent triggering
of event evaluation
due to radio signal
fluctuations. This
reduces the
LBFD-00201801 /
pong handovers or
TDLBFD-00201801
handover decision NO NO No
LOFD-001032 /
errors. A larger
TDLOFD-001032
value of this
The hysteresis for
event A3
associated with
inter-frequency
handover is the
same as the value
of this parameter.
For details, see
3GPP TS 36.331.
for event A3. If the
parameter is set to
a large value, an
intra-frequency
handover is
performed only
when the signal
LBFD-00201801 /
quality of the NO NO No
TDLBFD-00201801
neighboring cell is
than that of the
serving cell and
other triggering
conditions are met.
For details, see
3GPP TS 36.331.
handover.
When the UE
detects that the
signal quality in the
serving cell and that
in at least one
neighboring cell
meet the entering
condition, it does
not immediately
send a
measurement
report to the
eNodeB. Instead,
the UE sends a
report only when
the signal quality
meets the entering
LBFD-00201801 /
condition NO NO No
TDLBFD-00201801
throughout the
time-to-trigger.
This parameter
helps decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers, and the
number of incorrect
handovers,
preventing
unnecessary
handovers. The
time-to-trigger for
event A3
associated with
LOFD-001036 /
YES YES No
TDLOFD-001037
Indicates the name

of the operator. The
name is a string of
a maximum of 32
characters. The
string cannot be all
null characters or
contain any of the
following
characters: double LOFD-001036 /
quotation marks ("), TDLOFD-001036
NO YES No
commas (,), LOFD-001037 /
semicolons (;), TDLOFD-001037
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
spaces, and two or
more consecutive
percent signs (%).
Indicates the type

of the operator. The
operator can be the
primary operator or
LOFD-001036 /
a secondary
TDLOFD-001036
operator. For each NO YES No
LOFD-001037 /
eNodeB, only one
TDLOFD-001037
primary operator
but more than one
secondary operator
can be configured.
LOFD-001036 /
TDLOFD-001036
country code (MCC) NO YES No
LOFD-001037 /
of the operator.
TDLOFD-001037
network code
(MNC) of the
operator. The value LOFD-001036 /
of this parameter is TDLOFD-001036
NO YES No
a string of two or LOFD-001037 /
three characters, TDLOFD-001037
each of which must
be a digit in the
range from 0 to 9.
Indicates the ID of
YES YES No None
the IP path.
LOFD-001036 /
Indicates the ID of TDLOFD-001036
NO YES No
the operator. LOFD-001037 /
TDLOFD-001037
Indicates the
tracking area ID, LOFD-001036 /
which uniquely TDLOFD-001036
YES YES No
identifies an entry LOFD-001037 /
of tracking area TDLOFD-001037
information.
LOFD-001036 /
NO YES No
TDLOFD-001037
Indicates the
tracking area code
(TAC), which is
used by the EPC to
determine the area
within which paging
messages are sent.
One tracking area
is comprised of one
or more cells. Two LOFD-001036 /
TAC values TDLOFD-001036
NO YES No
0x0000(0) and LOFD-001037 /
0xFFFE(65534) are TDLOFD-001037
reserved according
to the protocol and
will not be used in
future versions.
Therefore, do not
use 0 or 65534 as a
TAC value in TAC
planning or
configuration.
LOFD-001036 /
YES YES No
TDLOFD-001037
Indicates whether
emergency calls. It
is recommended
that this parameter LBFD-002028 /
NO NO No
be set to a value in TDLBFD-002028
accordance with the
actual emergency
call capability of the
operator.
Indicates whether
the operator
supports LBFD-002028 /
NO NO No
emergency calls TDLBFD-002028
initiated by UEs in
limited mode.
Indicates the
Allocation and
Retention Priority
LBFD-002028 /
(ARP) value of the NO NO No
TDLBFD-002028
dedicated
emergency call
bearer.
Indicates the
Allocation and
Retention Priority LBFD-002028 /
NO NO No
(ARP) value of the TDLBFD-002028
default emergency
call bearer.
Indicates the
eNodeB sharing
mode, which can be
independent LOFD-001036 /
Operator Mode, TDLOFD-001036
NO NO No
Shared Frequency LOFD-001037 /
Sharing Mode, or TDLOFD-001037
Separate
Frequency Sharing
Mode.
LOFD-001036 /
YES YES No
TDLOFD-001037
Indicates the
proportion of the
maximum number
of users for the
LOFD-001036 /
operator at the
TDLOFD-001036
shared eNodeB. NO YES No
LOFD-001037 /
This parameter
TDLOFD-001037
must be set
according to the
contract signed by
the operators.
Indicates the
minimum length of
NO NO No None
the S1 re-
establishment timer.
Indicates the
maximum length of
NO NO No None
the S1 re-
establishment timer.
YES YES No
the S1 interface. TDLOFD-001018
Indicates the ID of
the Stream Control
Transmission LOFD-001018 /
NO YES No
Protocol (SCTP) TDLOFD-001018
link on the S1
interface.
LOFD-001018 /
the operator that LOFD-001036 /
NO YES No
owns the S1 TDLOFD-001036
interface. LOFD-001037 /
TDLOFD-001037
Indicates the
compliance protocol
release of the MME
to which the
eNodeB is
connected through
the S1 interface.
The value of this
parameter must be
the same as the
MME-complied
protocol release.
The eNodeB sends
LBFD-001001 /
S1 messages NO NO No
TDLBFD-001001
complying with the
protocol release
specified by this
parameter. If the
parameter value is
different from the
MME-complied
protocol release,
the way in which
the MME handles
these message is
subject to the MME
implementation.
Indicates whether
the S1 interface is
blocked. The BLK
S1INTERFACE
command is used
to block the S1 NO NO No None
interface. The UBL
S1INTERFACE
command is used
to unblock the S1
interface.

NO NO Yes None
of the S1 interface.
of the SCTP link on NO NO Yes None
the S1 interface.
Indicates whether
the MME connected
to the eNodeB is
overloaded. This
parameter is valid
after the S1
interface is set up.
Before the S1
interface is
LOFD-001018 /
successfully set up, NO NO Yes
TDLOFD-001018
this parameter is
NULL. For details
about how to
determine whether
the MME is
overloaded after the
S1 interface is set
up, see 3GPP TS
36.413.
Indicates the
number of users
NO NO Yes None
that have accessed
the S1 interface.
Indicates the name
of the MME to
which the eNodeB
NO NO Yes None
is connected
through the S1
interface.
Indicates the IDs of
all served PLMNs of
the MME to which LOFD-001018 /
the eNodeB is TDLOFD-001018
connected. The ID LOFD-001036 /
NO NO Yes
of a served PLMN TDLOFD-001036
consists of the MCC LOFD-001037 /
and MNC. PLMN TDLOFD-001037
IDs are separated
by commas (,).
Indicates the Global
Unique MME
Identifiers
(GUMMEIs) of all
MME to which the
eNodeB is
connected. A
GUMMEI of a NO NO Yes None
serving MME
consists of the
MCC, MNC, MME
group ID, and MME
code. GUMMEIs
are separated by
commas (,).
Indicates the
capacity of the
connected MME
relative to that of
other MMEs. A
larger value of this NO NO Yes None
parameter indicates
a larger capacity
allowing UE access.
For details, see
3GPP TS 36.413.
Indicates the
reason of the fault NO NO Yes None
on the S1 link.
Indicates the ID of
YES YES No None
an S1 interface.
Indicates whether
the MME at the
other end of the S1
interface supports
Huawei-proprietary
positioning
procedures, which
are included in
minimization of
drive tests (MDT).
The value DISABLE
indicates that the
NO NO No None
MME does not
support the
procedures and
therefore the
eNodeB cannot
obtain UE location
information from the
MME through the
procedures. The
value ENABLE
indicates the
opposite.

country code of the
neighboring
eNodeB to be
added to the list. LOFD-002004 /
The value of this TDLOFD-002004
YES YES No
parameter is a LOFD-002001 /
string of three TDLOFD-002001
characters, each of
which must be a
digit in the range of
0 to 9.
network code of the
neighboring
eNodeB to be
added to the list. LOFD-002004 /
The value of this TDLOFD-002004
YES YES No
parameter is a LOFD-002001 /
string of two or TDLOFD-002001
three characters,
each of which must
be a digit in the
range of 0 to 9.

the neighboring TDLOFD-002004
YES YES No
eNodeB to be LOFD-002001 /
added to the list. TDLOFD-002001
Indicates whether
the list is a blacklist
or whitelist.If the
peer eNodeB is in
the X2 blacklist, the
X2 interface
between the two
eNodeBs cannot be LOFD-002004 /
manually or TDLOFD-002004
NO NO No
automatically set LOFD-002001 /
up. If the peer TDLOFD-002001
eNodeB is in the X2
whitelist, the X2
interface between
the two eNodeBs
cannot be
automatically
removed.
LBFD-002018 /
TDLBFD-002018
Indicates the ID of LBFD-00201801 /
YES YES No
the X2 interface. TDLBFD-00201801
LBFD-00201802 /
TDLBFD-00201802
Indicates the ID of
the Stream Control
Transmission
NO YES No None
Protocol (SCTP)
link on the X2
interface.
the operator that TDLOFD-001036
NO YES No
owns the X2 LOFD-001037 /
interface. TDLOFD-001037
Indicates the
protocol release LBFD-001001 /
NO NO No
with which the peer TDLBFD-001001
eNodeB complies.
Indicates whether
the X2 interface can
be automatically
removed when the
peer-eNodeB
configuration is
deleted. This
parameter is valid
only when peer-
eNodeB information
for SON is
configured. This
parameter will be NO NO No None
removed in later
versions. In this
version, the setting
still synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
Indicates the ID of
the neighboring
eNodeB to which
the local eNodeB is
connected through
the X2 interface.
The combination of NO NO Yes None
this parameter and
NbrEnbPlmnId
uniquely identifies
the neighboring
eNodeB around the
globe.
Indicates the PLMN

ID of the
neighboring
eNodeB to which NO NO Yes None
the local eNodeB is
connected through
the X2 interface.
of the X2 interface.
If the status is
normal, the X2
interface has been
NO NO Yes None
successfully set up.
If the status is
abnormal, the X2
interface has failed
to be set up.
Indicates the
reason why the X2
NO NO Yes None
interface is
abnormal.
Indicates the DRX LBFD-002017 /

NO NO No
switch. TDLBFD-002017
Indicates whether
short DRX cycles. LBFD-002017 /
NO NO No
Short DRX cycles TDLBFD-002017
reduce the traffic
delay.
of a long DRX cycle
that is applied only
to non-power-
saving UEs whose
subscriber profile ID
for RAT/frequency
priority (RFSP)
indexes are
contained in the
RFSP index set.
Due to the
constraints of the
SRS bandwidth and
the
TimeAlignmentTime
LBFD-002017 /
r parameter (TA NO NO No
TDLBFD-002017
period), the actual
value of this
parameter assigned
to a UE may be
less than the
configured value. If
you hope that the
value actually
assigned to a UE is
equal to or greater
than 80 ms, set the
TimeAlignmentTime
r parameter to a
value equal to or
greater than 2560
ms.
of the On Duration
Timer that applies
only to non-power-
saving UEs whose
RFSP indexes are
contained in the
RFSP index set.
For details about
this timer, see
3GPP TS 36.321. LBFD-002017 /
NO NO No
Due to the impact TDLBFD-002017
of CQI reporting
intervals and SRS
transmission
intervals, there is a
possibility that the
actual value of this
parameter assigned
to a UE is larger
than the configured
value.
of the DRX
Inactivity Timer that
applies only to non-
power-saving UEs
whose RFSP LBFD-002017 /
NO NO No
indexes are TDLBFD-002017
contained in the
RFSP index set.
For details about
this timer, see
3GPP TS 36.321.
Indicates whether
short DRX cycles
for non-power- LBFD-002017 /
NO NO No
saving UEs whose TDLBFD-002017
RFSP indexes are
contained in the
RFSP index set.
of a short DRX
cycle that applies
only to non-power- LBFD-002017 /
NO NO No
saving UEs whose TDLBFD-002017
RFSP indexes are
contained in the
RFSP index set.

of the DRX Short
Cycle Timer that
applies only to non-
power-saving UEs
whose RFSP
indexes are
contained in the
RFSP index set.
The length of this
timer is expressed
in the number of LBFD-002017 /
NO NO No
short DRX cycles. If TDLBFD-002017
this parameter is
set to 1, the length
of this timer is one
short DRX cycle. If
this parameter is
set to 2, the length
of this timer is two
short DRX cycles.
For details, see
3GPP TS 36.321
5.7.
Indicates the long
DRX cycle for intra-
RAT ANR. If intra-
RAT ANR is
enabled, this
parameter takes
effect regardless of
whether DRX is
enabled.If a long
DRX cycle is
configured for ANR
measurements, it is
recommended that
this parameter be
set to a value equal
to or greater than
256 ms to ensure
that the UE can
successfully obtain
the CGI of a cell.
However, if this
parameter is set to
a large value, the
delay of obtaining
the CGI is large,
and therefore the
system delay is also
large.
Indicates the long

DRX cycle for inter-
RAT ANR. If inter-
RAT ANR is
LBFD-002017 /
enabled, this NO NO No
TDLBFD-002017
parameter is valid
regardless of
whether DRX is
enabled.
Indicates the
extended QoS
LOFD-001015 /
Class Identifier
TDLOFD-001015
(QCI), which is YES YES No
LOFD-00101502 /
required by the
TDLOFD-00101502
operator for user
differentiation.
service type TDLOFD-001015
NO NO No
corresponding to LOFD-00101502 /
the extended QCI. TDLOFD-00101502
Indicates the weight LOFD-001015 /

factor used in the TDLOFD-001015
calculation of LOFD-00101502 /
NO NO No
connection priorities TDLOFD-00101502
during uplink LOFD-003011 /
scheduling. TDLOFD-003011
Indicates the weight

factor used in the LOFD-001015 /
calculation of TDLOFD-001015
NO NO No
connection priorities LOFD-00101502 /
during downlink TDLOFD-00101502
scheduling.
LBFD-002025 /
minimum
TDLBFD-002025
guaranteed bit rate NO NO No
LOFD-001015 /
of the non-GBR
TDLOFD-001015
service.
Indicates the
LBFD-002025 /
downlink minimum
TDLBFD-002025
LOFD-001015 /
of the non-GBR
TDLOFD-001015
service.
Indicates the pre-
allocation weight.
The pre-allocation
weight of a UE is
the pre-allocation
weight of services
carried by the
highest-priority
logical channel. If
services carried by
highest-priority
logical channels
have different pre-
allocation weights,
LBFD-002025 /
the UE takes the
TDLBFD-002025
highest pre- NO NO No
LOFD-001015 /
allocation weight.
TDLOFD-001015
When resources
are insufficient, pre-
allocation weights
affect the pre-
allocation
probabilities of
users. The pre-
allocation
probability has a
positive correlation
with the pre-
allocation weight.
This parameter is
QCI-specific.
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021
LOFD-001022 /
TDLOFD-001022
LOFD-001023 /
Indicates the group TDLOFD-001023
ID of the LOFD-001043 /
parameters related TDLOFD-001043
NO NO No
to the inter-RAT LOFD-001045 /
handover with the TDLOFD-001045
extended QCI. LOFD-001044 /
TDLOFD-001044
LOFD-001046 /
TDLOFD-001046
LOFD-001033 /
TDLOFD-001033
LOFD-001034 /
TDLOFD-001034
LOFD-001035
Indicates the
prioritized bit rate of
the logical channel.
The UE scheduler
guarantees LBFD-002025 /
prioritized bit rates TDLBFD-002025
NO NO No
of logical channels LOFD-001015 /
in descending order TDLOFD-001015
of logical channel
priority. For details,
see 3GPP TS
36.321.
Indicates the
priority of the logical
channel. The UE
scheduler
guarantees
prioritized bit rates
of logical channels
in descending order
LBFD-002025 /
of logical channel
TDLBFD-002025
priority. Resources NO NO No
LOFD-001015 /
are allocated in
TDLOFD-001015
descending order of
logical channel
priority after the
of all services are
guaranteed. For
details, see 3GPP
TS 36.321.
Indicates the ID of
LBFD-002008 /
an RLC/PDCP NO NO No
TDLBFD-002008
parameter group.
Indicates whether LBFD-002025 /

the extended QCI is TDLBFD-002025
NO NO No
specific to free LOFD-001015 /
users or paid users. TDLOFD-001015
LOFD-00301101 /
TDLOFD-00301101
LOFD-00301102 /
TDLOFD-00301102
LOFD-00301103 /
TDLOFD-00301103
Indicates whether
LOFD-00301202 /
to enable flow NO NO No
TDLOFD-00301202
control for the QCI.
LOFD-003016 /
TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-003011 /
TDLOFD-003011
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021
LOFD-001022 /
TDLOFD-001022
LOFD-001023 /
TDLOFD-001023
Indicates the group LOFD-001032 /
ID of the TDLOFD-001032
parameters related LOFD-001043 /
YES YES No
to the inter-RAT TDLOFD-001043
handover with a LOFD-001045 /
specific QCI. TDLOFD-001045
LOFD-001044 /
TDLOFD-001044
LOFD-001046 /
TDLOFD-001046
LOFD-001033 /
TDLOFD-001033
LOFD-001034 /
TDLOFD-001034
LOFD-001035
UTRAN.
If this switch is set
to On, the UE can
perform the PS
handover to the
UTRAN cell.
to Off, the UE
cannot perform the
PS handover to the
UTRAN cell.
SRVCC: Indicates
the switch used to
enable or disable
the QCI-specific
SRVCC handover
to UTRAN.
If this switch is set LOFD-001022 /
to On, the UE can TDLOFD-001022
NO NO No
perform the SRVCC LOFD-001019 /
handover to the TDLOFD-001019
UTRAN cell.
to Off, the UE
cannot perform the
SRVCC handover
to the UTRAN cell.
REDIRECTION:
used to enable or
disable QCI-specific
redirections to
UTRAN.
to On, the UE can
perform the
redirection to the
UTRAN cell.
used to enable or
disable the single
radio voice call
continuity (SRVCC)
handover to
GERAN GSM.
to On, the UE can LOFD-001023 /
NO NO No
perform the SRVCC TDLOFD-001023
handover to the
GERAN GSM cell.
to Off, the UE
cannot perform the
SRVCC handover
to the GERAN GSM
cell.
Indicates whether
PS handovers to
neighboring
GPRS/EDGE cells
are allowed.
NACC_HO:
Indicates whether
NACC handovers to
neighboring
GPRS/EDGE cells
are allowed. This
switch will be
removed in the later
versions. In this
of this switch is still
synchronized
between the M2000
and the eNodeB, LOFD-001020 /
NO NO No
but it is no longer TDLOFD-001020
used internally.
Therefore, avoid
using this
parameter.
CCO_HO:
Indicates whether
CCO handovers to
neighboring
GPRS/EDGE cells
are allowed.
SRVCC:
Indicates whether
SRVCC handovers
to neighboring
GPRS/EDGE cells
are allowed.
REDIRECTION:
Indicates whether
used to enable or
disable QCI-specific
SRVCC to
CDMA2000 1xRTT.
If this switch is
turned on, UEs can
perform SRVCC to
CDMA2000 1xRTT
cells.
If this switch is
turned off, UEs
cannot perform
SRVCC to
CDMA2000 1xRTT
cells.
PS_HO: Indicates
the switch used to
enable or disable
the QCI-specific PS
handover to
CDMA2000 HRPD.
to On, the UE can
perform the PS
handover to the
CDMA2000 HRPD
cell.
to Off, the UE
cannot perform the
PS handover to the
CDMA2000 HRPD
cell.
OMT_HO: Indicates
the switch used to
enable or disable
the QCI-specific
OMT handover to
CDMA2000 HRPD.
to On, the UE can
perform the OMT
handover to the
CDMA2000 HRPD
cell.
to Off, the UE
cannot perform the
OMT handover to
the CDMA2000
HRPD cell.
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021
LOFD-001022 /
TDLOFD-001022
LOFD-001023 /
TDLOFD-001023
LOFD-001032 /
Indicates whether
TDLOFD-001032
to permit or forbid
LOFD-001043 /
the inter-RAT NO NO No
TDLOFD-001043
handover under the
LOFD-001045 /
QCI.
TDLOFD-001045
LOFD-001044 /
TDLOFD-001044
LOFD-001046 /
TDLOFD-001046
LOFD-001033 /
TDLOFD-001033
LOFD-001034 /
TDLOFD-001034
LOFD-001035
Indicates whether
to allow the fast
ANR under the
QCI. The function
specified by this LOFD-002001 /
parameter is an NO NO No TDLOFD-002001
extended function LOFD-002002
and is reserved.
The current version
does not support
this function.
Indicates the index
mapped to the MCS
offset for channel
quality indicators NO NO No None
(CQIs) transmitted
with data on
PUSCH.
Indicates the index
mapped to the MCS
offset for rank
indications (RIs)
transmitted with
data on PUSCH.
The protocol does
not recommend the
values 13, 14, and NO NO No None
15. If this parameter
is set to 13, 14, or
15, If this value is
used, the UE
performance may
deteriorate. For
details, see 3GPP
TS 36.213.
Indicates the index

mapped to the MCS
offset for
acknowledgments
(ACKs) transmitted
with data on
PUSCH. The
protocol does not
recommend the NO NO No None
value 15. If this
parameter is set to
15, If this value is
used, the UE
performance may
deteriorate. For
details, see 3GPP
TS 36.213.
Indicates the ID of
LBFD-002008 /
the RLC/PDCP YES YES No
TDLBFD-002008
parameter group.
LBFD-002008 /
of the PDCP NO NO No
TDLBFD-002008
discard timer.
Indicates the RLC

transmission mode.
LBFD-002008 /
Only the AM and NO NO No
TDLBFD-002008
UM modes are
available.
Indicates the UE-
specific maximum
number of RLC
ARQ
retransmissions,
namely the
maximum number
of AM PDU LBFD-002008 /
NO NO No
retransmissions. TDLBFD-002008
When the number
of retransmissions
reaches the value
of this parameter,
RRC connection re-
establishment is
initiated.
Indicates the
eNodeB-specific
maximum number
of RLC ARQ
retransmissions,
namely the
maximum number
of AM PDU LBFD-002008 /
NO NO No
retransmissions. TDLBFD-002008
When the number
of retransmissions
reaches the value
of this parameter,
RRC connection re-
establishment is
initiated.
Indicates the UE-
specific data
volume threshold of
PDUs to trigger
polling. When the
LBFD-002008 /
transmitted data NO NO No
TDLBFD-002008
volume reaches the
value of this
parameter, the Poll
flag is set in the
PDU header.
Indicates the
eNodeB-specific
data volume
threshold of PDUs
to trigger polling.
When the LBFD-002008 /
NO NO No
transmitted data TDLBFD-002008
volume reaches the
value of this
parameter, the Poll
flag is set in the
PDU header.
Indicates the UE-
specific number of
PDUs to trigger
polling. When the
transmitted number LBFD-002008 /
NO NO No
of PDUs reaches TDLBFD-002008
the value of this
parameter, the Poll
flag is set in the
PDU header.
Indicates the
eNodeB-specific
number of PDUs to
trigger polling.
When the
LBFD-002008 /
transmitted number NO NO No
TDLBFD-002008
of PDUs reaches
the value of this
parameter, the Poll
flag is set in the
PDU header.
of the Polling PDU LBFD-002008 /
NO NO No
retransmission TDLBFD-002008
timer for the UE.
of the Polling PDU
LBFD-002008 /
retransmission NO NO No
TDLBFD-002008
timer for the
eNodeB.
of the UE-specific
timer for prohibiting LBFD-002008 /
NO NO No
status reporting TDLBFD-002008
from the receiver in
AM.
of the eNodeB-
specific timer for LBFD-002008 /
NO NO No
prohibiting status TDLBFD-002008
reporting from the
receiver in AM.
of the UE-specific
LBFD-002008 /
timer for reordering NO NO No
TDLBFD-002008
at the receiver in
AM.
of the eNodeB-
LBFD-002008 /
specific timer for NO NO No
TDLBFD-002008
reordering at the
receiver in AM.

of a PDCP
LBFD-002008 /
sequence number NO NO No
TDLBFD-002008
of a UL DRB in RLC
UM.
of a UL RLC
sequence number LBFD-002008 /
NO NO No
in UM. The length is TDLBFD-002008
permanently 10 bits
in AM.

of a DL RLC
sequence number LBFD-002008 /
NO NO No
in UM. The length is TDLBFD-002008
permanently 10 bits
in AM.
of the UE-specific
LBFD-002008 /
timer for reordering NO NO No
TDLBFD-002008
at the receiver in
UM.
of the eNodeB-
LBFD-002008 /
specific timer for NO NO No
TDLBFD-002008
reordering at the
receiver in UM.
Indicates whether a
PDCP status report LBFD-002008 /
NO NO No
is required upon TDLBFD-002008
handover in AM.
Indicates the QoS
Class Identifier
(QCI) of an EPS
bearer. Different
QCIs represent
different QoS
specifications such
LOFD-001015 /
as the packet delay
TDLOFD-001015
budget, packet YES YES No
LOFD-00101502 /
error loss rate, and
TDLOFD-00101502
resource type
(whether the
service is a GBR
details, see Table
6.1.7 in 3GPP TS
23.203.
Indicates the weight LOFD-001015 /

factor used in the TDLOFD-001015
calculation of LOFD-00101502 /
NO NO No
connection priorities TDLOFD-00101502
during uplink LOFD-003011 /
scheduling. TDLOFD-003011

factor used in the LOFD-001015 /
calculation of TDLOFD-001015
NO NO No
connection priorities LOFD-00101502 /
during downlink TDLOFD-00101502
scheduling.
LBFD-002025 /
TDLBFD-002025
LOFD-001015 /
TDLOFD-001015
minimum
LBFD-003002 /
TDLBFD-003002
of the non-GBR
LOFD-00101502 /
service.
TDLOFD-00101502
LOFD-003011 /
TDLOFD-003011
LBFD-002025 /
TDLBFD-002025
LOFD-001015 /
Indicates the
TDLOFD-001015
downlink minimum
LBFD-003002 /
TDLBFD-003002
of the non-GBR
LOFD-00101502 /
service.
TDLOFD-00101502
LOFD-003011 /
TDLOFD-003011
Indicates the pre-
allocation weight.
The pre-allocation
weight of a UE is
the pre-allocation
weight of services
carried by the
highest-priority
logical channel. If
services carried by
highest-priority
logical channels
have different pre-
LBFD-002025 /
allocation weights,
TDLBFD-002025
the UE takes the
LOFD-001015 /
highest pre- NO NO No
TDLOFD-001015
allocation weight.
LOFD-00101502 /
When resources
TDLOFD-00101502
are insufficient, pre-
allocation weights
affect the pre-
allocation
probabilities of
users. The pre-
allocation
probability has a
with the pre-
allocation weight.
This parameter is
QCI-specific.
LOFD-001019 /
TDLOFD-001019
LOFD-001020 /
TDLOFD-001020
LOFD-001021
LOFD-001022 /
TDLOFD-001022
LOFD-001023 /
TDLOFD-001023
parameter group TDLOFD-001043
NO NO No
related to inter-RAT LOFD-001045 /
handover. TDLOFD-001045
LOFD-001044 /
TDLOFD-001044
LOFD-001046 /
TDLOFD-001046
LOFD-001033 /
TDLOFD-001033
LOFD-001034 /
TDLOFD-001034
LOFD-001035
LBFD-002025 /
Indicates the ID of
TDLBFD-002025
an RLC/PDCP NO NO No
LOFD-001015 /
parameter group.
TDLOFD-001015
Indicates the
prioritized bit rate of
the logical channel.
The UE scheduler LBFD-002025 /
guarantees TDLBFD-002025
prioritized bit rates LOFD-001015 /
NO NO No
of logical channels TDLOFD-001015
in descending order LOFD-00101502 /
of logical channel TDLOFD-00101502
priority. For details,
see 3GPP TS
36.321.
Indicates the
priority of the logical
channel. The UE
scheduler
guarantees
of logical channels
in an ascending
order of logical LBFD-002025 /
channel priorities. TDLBFD-002025
NO NO No
Resources are LOFD-001015 /
allocated in an TDLOFD-001015
ascending order of
logical channel
priorities after the
of all services are
guaranteed. For
details, see 3GPP
TS 36.321.
LOFD-00301101 /
TDLOFD-00301101
LOFD-00301102 /
TDLOFD-00301102
LOFD-00301103 /
Indicates whether
TDLOFD-00301103
to enable flow NO NO No
LOFD-00301202 /
control for the QCI.
TDLOFD-00301202
LOFD-003016 /
TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
Indicates the
default Doppler shift
level. This is the
default parameter
used when Doppler LOFD-00101502 /
NO NO No
shift measurement TDLOFD-00101502
is not required. This
parameter is
unavailable in this
version.
of adaptive
beamforming and
MIMO (BFMIMO)
for a multi-antenna
eNodeB. The
values are
described as
follows:
NO_ADAPTIVE: A
fixed BFMIMO
transmission mode
is used. That is,
transition between
BFMIMO
transmission modes
is not supported.
TxD_BF_ADAPTIV LOFD-001001 /
E: The transmission TDLOFD-001001
mode changes NO NO No LOFD-001003 /
adaptively between TDLOFD-001003
TM2 and TM7 or TDLOFD-009003
between TM2 and
TM8, depending on
the protocol release
with which UEs
comply.
MIMO_BF_ADAPTI
VE: The
transmission mode
changes adaptively
between TM2, TM3,
and TM7 or
between TM2, TM3,
and TM8,
depending on the
protocol release
with which UEs
Indicates the fixed
beamforming and
MIMO (BFMIMO)
transmission mode
configured by a
multi-antenna
eNodeB for UEs.
This parameter is
valid only when
BfMimoAdaptiveSwi
tch is set to
NO_ADAPTIVE.
There are five LOFD-001001 /
values. TDLOFD-001001
TM2: Transmission NO NO No LOFD-001003 /
mode 2 is always TDLOFD-001003
used for UEs. TDLOFD-009003
TM3: Transmission
mode 3 is always
used for UEs.
TM7: Transmission
mode 7 is always
used for UEs.
TM8: Transmission
mode 8 is always
used for UEs.
TM4: Transmission
mode 4 is always
used for UEs.
Indicates whether
CQI reporting
LBFD-002025 /
period adaptation. NO NO No
TDLBFD-002025
This parameter is
valid only for FDD
cells.
Indicates the fixed
CQI reporting
period. A fixed CQI
reporting period is
used when CQI
reporting period
adaptation is
disabled. If the
UserCqiPeriodCfg
parameter is set to
32 ms, the eNodeB
automatically
changes the value
to 20 ms. If the
LBFD-002025 /
UserCqiPeriodCfg NO NO No
TDLBFD-002025
parameter is set to
64 ms, the eNodeB
automatically
changes the value
to 40 ms. If the
UserCqiPeriodCfg
parameter is set to
128 ms, the
eNodeB
automatically
changes the value
to 80 ms.This
parameter is valid
only for FDD cells.
of adaptive MIMO
for a multi-antenna
eNodeB. The
values are
described as
follows:
NO_ADAPTIVE: A
fixed MIMO
transmission mode
is used. That is,
transition between
MIMO transmission
modes is not
supported.
OL_ADAPTIVE:
open-loop adaptive
MIMO transmission
LOFD-001001 /
mode. UEs report
TDLOFD-001001
RANK and CQI NO NO No
LOFD-001003 /
values but do not
TDLOFD-001003
report PMI values
to the eNodeB.
CL_ADAPTIVE:
closed-loop
adaptive MIMO
transmission mode.
UEs report RANK,
CQI, and PMI
values to the
eNodeB.
OC_ADAPTIVE:
UEs switch
between the open-
loop and closed-
loop adaptive
MIMO transmission
modes
Indicates the fixed
MIMO transmission
mode for a multi-
antenna eNodeB.
This parameter is
valid only when
MimoAdaptiveSwitc
h is set to
NO_ADAPTIVE.
There are four
values.
TM2: Transmission
LOFD-001001 /
mode 2 is
TDLOFD-001001
permanently NO NO No
LOFD-001003 /
applied to UEs.
TDLOFD-001003
TM3: Transmission
mode 3 is
permanently
applied to UEs.
TM4: Transmission
mode 4 is
permanently
applied to UEs.
TM6: Transmission
mode 6 is
permanently
applied to UEs.
Indicates whether
SRS period
adaptation. If this
parameter is set to
ON, the SRS period
adaptively changes
LBFD-002025 /
based on the SRS NO NO No
TDLBFD-002025
algorithm. If this
parameter is set to
OFF, the SRS
period is the value
of the
UserSrsPeriodCfg
parameter.
Indicates the fixed
SRS period. A fixed
SRS period is used LBFD-002025 /
NO NO No
when SRS period TDLBFD-002025
adaptation is
disabled.
Indicates the QoS

class identifier
(QCI).
QCI 1 indicates
voice services.
QCI 2 indicates
video (live
streaming) services.
QCI 3 indicates
real-time gaming
services.
QCI 4 indicates
YES YES No None
video (buffered
streaming) services.
QCI 5 indicates IMS
signaling.
QCI 7 indicates
voice, video, and
interactive gaming
services.
QCIs 6, 8, and 9
indicate video
services and TCP-
based services.
of the timer for
periodic
transmission of
buffer status reports
(BSRs).
BSRs are sent
periodically or as
triggered by events.
Periodic
NO NO No None
transmission of
BSRs uses the
timer specified by
this parameter.
When the timer
expires, a BSR is
sent.
After the BSR is
sent, the timer is
restarted.

of the BSR
retransmission
NO NO No None
timer. This timer is
started after a BSR
is sent.
Indicates the
measurement gap
pattern.
The eNodeB
defines
measurement gaps
for UEs in
connected mode.
During the
LBFD-00201802 /
measurement gaps,
TDLBFD-00201802
a UE measures the
LBFD-00201804 /
signal quality of the
TDLBFD-00201804
cells on a specific
LOFD-001019 /
frequency.
TDLOFD-001019
There are two gap
LOFD-001020 /
patterns: pattern 1
TDLOFD-001020
and pattern 2. In
LOFD-001021 /
pattern 1, the gap NO NO No
TDLOFD-001021
width is 6 ms and
LOFD-001032 /
the repetition period
TDLOFD-001032
is 40 ms. In pattern
LOFD-001072 /
2, the gap width is 6
TDLOFD-001045
ms and the
LOFD-001073 /
repetition period is
TDLOFD-001073
80 ms.
LBFD-00201805 /
For details, see
TDLBFD-00201805
3GPP TS 36.331.
Pattern 1 and
pattern 2
correspond to Gap
Pattern Id 0 and
Gap Pattern Id 1
specified in 3GPP
TS 36.331,
respectively.
Indicates the upper-

layer filtering
coefficient for
RSRP
measurements on
LBFD-00201801 /
E-UTRAN.
TDLBFD-00201801
A large value of this
LBFD-00201802 /
parameter indicates
TDLBFD-00201802
a strong smoothing NO NO No
LBFD-00201804 /
effect and high
TDLBFD-00201804
resistance to fast
LOFD-001032 /
fading, but it
TDLOFD-001032
weakens the tracing
capability towards
varying signals. For
details, see 3GPP
TS 36.331.
layer filtering
coefficient for
RSRQ
measurements on
E-UTRAN. LBFD-00201801 /
A larger value of TDLBFD-00201801
this parameter LBFD-00201802 /
indicates a stronger TDLBFD-00201802
NO NO No
smoothing effect LBFD-00201804 /
and higher TDLBFD-00201804
resistance to fast LOFD-001032 /
fading, but it may TDLOFD-001032
weaken the tracing
capability towards
details, see 3GPP
TS 36.331.
Indicates the L3
used for the
measurement
quantity in inter-
LOFD-001020 /
RAT measurements
TDLOFD-001020
of GERAN.
LOFD-001045 /
A great value of this
TDLOFD-001045
parameter indicates NO NO No
LOFD-001046 /
a strong smoothing
TDLOFD-001046
effect and a high
LOFD-001073 /
anti-fast-fading
TDLOFD-001073
capability, but a low
signal change
tracing capability.
For details, see
3GPP TS 36.331.
LBFD-00201801 /
TDLBFD-00201801
LBFD-00201802 /
TDLBFD-00201802
LBFD-00201804 /
TDLBFD-00201804
Indicates whether LOFD-001019 /
the measurement TDLOFD-001019
threshold needs to LOFD-001020 /
be set. TDLOFD-001020
If this parameter is LOFD-001021 /
set to CFG, the TDLOFD-001021
SMeasure LOFD-001032 /
NO NO No
parameter needs to TDLOFD-001032
be set. If this LOFD-001044 /
NOT_CFG, the LOFD-001045 /
SMeasure TDLOFD-001045
parameter does not LOFD-001046 /
need to be set. TDLOFD-001046
LOFD-001072 /
TDLOFD-001072
LOFD-001073 /
TDLOFD-001073
LBFD-00201805 /
TDLBFD-00201805
Indicates the
threshold below
LBFD-00201801 /
which
TDLBFD-00201801
measurements on
LBFD-00201802 /
neighboring cells
TDLBFD-00201802
are started. If the
LBFD-00201804 /
TDLBFD-00201804
serving cell
LOFD-001019 /
exceeds this
TDLOFD-001019
threshold, the UE is
LOFD-001020 /
not required to
TDLOFD-001020
perform intra-
LOFD-001021 /
frequency, inter-
TDLOFD-001021
frequency, or inter-
LOFD-001032 /
RAT NO NO No
TDLOFD-001032
measurements,
LOFD-001044 /
leading to reduced
TDLOFD-001044
power
LOFD-001045 /
consumption. The
TDLOFD-001045
value -141 does not
LOFD-001046 /
take effect, and is
TDLOFD-001046
reserved for
LOFD-001072 /
backward
TDLOFD-001072
LOFD-001073 /
parameter is set to
TDLOFD-001073
LBFD-00201805 /
is used as the
TDLBFD-00201805
threshold in
implementation.
Indicates whether
mobility-based cell
handover
measurement
parameters need to
be set.
set to CFG, the
system supports
LOFD-001007 /
setting of mobility-
TDLOFD-001007
based handover NO NO No
LOFD-001008 /
measurement
TDLOFD-001008
parameters. If this
parameter is set to
NOT_CFG, the
system does not
support setting of
mobility-based
handover
measurement
parameters.
Indicates the cycle
during which
evaluations of the
UE medium and
high mobility states
in
RRC_CONNECTE
D mode are
performed. It is one
of the key
parameters in
deciding on a UE's
mobility state. If this LOFD-001007 /
NO NO No
a small value, LOFD-001008 /
switchings among TDLOFD-001008
mobility states are
frequent and the
decision precision is
relatively low. If this
parameter is set to
a large value,
switchings among
mobility states are
not frequent and
the decision
precision is
relatively high.
Indicates the cycle

during which
evaluations of the
UE normal mobility
state in
RRC_CONNECTE
D mode are
performed. It is one
of the key
parameters in
deciding on a UE's
mobility state. If this
LOFD-001007 /
parameter is set to
TDLOFD-001007
a small value, NO NO No
LOFD-001008 /
switchings among
TDLOFD-001008
mobility states are
frequent and the
decision precision is
relatively low. If this
parameter is set to
a large value,
switchings among
mobility states are
not frequent and
the decision
precision is
relatively high.
Indicates the
handover number
threshold used in
the UE medium
mobility state
evaluation. If the
number of
handovers
performed during a
period of time
LOFD-001007 /
specified by the NO NO No
TDLOFD-001007
TcrMaxConnMode
parameter exceeds
the value of this
parameter, the UE
is considered to be
in medium mobility
state and its
handover-related
parameters are
adjusted.
Indicates the
handover number
threshold used in
the UE high mobility
state evaluation. If
the number of
handovers
performed during a
period of time LOFD-001007 /
specified by the TDLOFD-001007
NO NO No
TcrMaxConnMode LOFD-001008 /
parameter exceeds TDLOFD-001008
the value of this
parameter, the UE
is considered to be
in high mobility
state and its
handover-related
parameters are
adjusted.
Indicates the
scaling factor for
the time-to-trigger
defined for medium-
mobility UEs. For a
UE in medium
LOFD-001007 /
mobility, the time-to- NO NO No
TDLOFD-001007
trigger used in
event evaluation is
multiplied by this
scaling factor, to
facilitate triggering
of the handover.
Indicates the
scaling factor for
the time-to-trigger
defined for high-
mobility UEs. For a
LOFD-001007 /
UE in high mobility,
TDLOFD-001007
the time-to-trigger NO NO No
LOFD-001008 /
used in event
TDLOFD-001008
evaluation is
multiplied by this
scaling factor, to
facilitate triggering
of the handover.
Indicates the
for RSCP
measurements on
UTRAN. LOFD-001019 /
A large value of this TDLOFD-001019
parameter indicates LOFD-001044 /
a strong smoothing TDLOFD-001044
NO NO No
effect and high LOFD-001043 /
resistance to fast TDLOFD-001043
fading, but it LOFD-001072 /
weakens the tracing TDLOFD-001072
capability towards
details, see 3GPP
TS 36.331.

layer filtering
coefficient for Ec/No
measurements on
UTRAN. LOFD-001019 /
A large value of this TDLOFD-001019
a strong smoothing TDLOFD-001044
NO NO No
effect and high LOFD-001043 /
resistance to fast TDLOFD-001043
fading, but it LOFD-001072 /
weakens the tracing TDLOFD-001072
capability towards
details, see 3GPP
TS 36.331.
Indicates the
LOFD-001020 /
maximum number
TDLOFD-001020
of cells to be
LOFD-001023 /
included in the
TDLOFD-001023
measurement
LOFD-001021
report after an inter-
LOFD-001019 /
RAT handover
event or a periodic
LOFD-001022 /
inter-RAT
TDLOFD-001022
measurement for
LOFD-001043 /
ANR purposes is
TDLOFD-001043
triggered. For
LOFD-001046 /
details, see 3GPP
TDLOFD-001046
TS 36.331.
Indicates the
number of
periodical LOFD-001020 /
measurement TDLOFD-001020
reports to be sent LOFD-001023 /
after an inter-RAT TDLOFD-001023
handover event is LOFD-001021
triggered. It is used LOFD-001019 /
to prevent the NO NO No TDLOFD-001019
impact of LOFD-001022 /
report loss and LOFD-001043 /
internal processing TDLOFD-001043
failure on the LOFD-001046 /
handover. For TDLOFD-001046
details, see 3GPP
TS 36.331.
Indicates the
interval at which
periodical
LOFD-001020 /
measurement
TDLOFD-001020
reports are sent
LOFD-001023 /
after the event for NO NO No
TDLOFD-001023
the handover to
LOFD-001046 /
GERAN is
TDLOFD-001046
triggered.
For details, see
3GPP TS 36.331.
Indicates the
quantity to be
included in the
measurements for
handovers to
UTRAN.
The RSCP values
are relatively stable,
while the Ec/No
values may vary LOFD-001019 /
with the network TDLOFD-001019
load. The value LOFD-001022 /
NO NO No
UTRAN_BOTH TDLOFD-001022
applies only to UEs LOFD-001043 /
complying with R10. TDLOFD-001043
For UEs complying
with R8 or R9, the
value
UTRAN_BOTH
takes the same
effect as the value
UTRAN_RSCP. For
details, see 3GPP
TS 23.003.
Indicates the
interval at which
periodical LOFD-001019 /
reports are sent LOFD-001022 /
NO NO No
after the event for TDLOFD-001022
the handover to LOFD-001043 /
UTRAN is triggered. TDLOFD-001043
For details, see
3GPP TS 36.331.
Indicates the
measurement
quantity required for
the inter-RAT
handover to
CDMA2000 1xRTT.
For details, see
3GPP TS 36.331.
Indicates the
interval at which
periodical
measurement
reports are sent
after the event for NO NO No LOFD-001021
the handover to
CDMA2000 1xRTT
is triggered.
For details, see
3GPP TS 36.331.
Indicates the
measurement
quantity required for
the inter-RAT
handover to
CDMA2000 HRPD.
For details, see
3GPP TS 36.331.
Indicates the
interval at which
periodic reports are
sent to the eNodeB
after the triggering
condition of the
event for inter-RAT
handover to
CDMA2000 HRPD
is met.
For details, see
3GPP TS 36.331.
Indicates the
quantity used to
evaluate the
triggering condition
for the inter-RAT
measurement event
A1 or A2. The
values are RSRP,
RSRQ and BOTH.
The measured
RSRP values are
LOFD-001020 /
stable, varying little
TDLOFD-001020
with the load, and
LOFD-001023 /
therefore there is
TDLOFD-001023
little signal
fluctuation. The
LOFD-001019 /
measured RSRQ
TDLOFD-001019
values vary with the
LOFD-001022 /
load and are likely
TDLOFD-001022
to reflect the signal
quality of the cell in
real time. By
default, the
reporting quantity
for the inter-RAT
handover event is
BOTH, that is, both
RSRP and RSRQ.
For details, see
3GPP TS 36.331.
Indicates the type
LOFD-001020 /
of the inter-RAT
TDLOFD-001020
handover event.
LOFD-001023 /
This parameter can
TDLOFD-001023
be set to EventB1
or EventB2. The
LOFD-001019 /
default value is
TDLOFD-001019
EventB1. For
LOFD-001022 /
details, see 3GPP
TDLOFD-001022
TS 36.331.
Indicates the
maximum number
of cells to be
included in the
measurement
report after an intra-
RAT inter-frequency
or intra-RAT intra- LBFD-00201801 /
frequency TDLBFD-00201801
NO NO No
measurement event LBFD-00201802 /
for handover TDLBFD-00201802
purposes or a
periodic intra-RAT
measurement for
ANR purposes is
triggered. For
details, see 3GPP
TS 36.331.
Indicates the
number of
periodical
measurement
reports to be sent
after an event for
the intra- or inter-
LBFD-00201801 /
frequency handover
TDLBFD-00201801
within the E-UTRAN
LBFD-00201802 /
is triggered. NO NO No
TDLBFD-00201802
It is used to prevent
LOFD-001032 /
the impact of
TDLOFD-001032
measurement
report loss and
internal processing
failure on the
handover. For
details, see 3GPP
TS 36.331.
Indicates the
quantity used to
evaluate the
for the intra-
frequency handover
event. The quantity
can be RSRP or
RSRQ.
The measured
RSRP values are
stable, varying little LBFD-00201801 /
NO NO No
with the load, and TDLBFD-00201801
therefore there is
little signal
fluctuation. The
measured RSRQ
load and are likely
real time.
For details, see
3GPP TS 36.331.
Indicates the
quantity to be
included in the
measurement
report for the intra-
frequency handover
event. The quantity
can be RSRP,
RSRQ, or both.
The measured
RSRP values are
with the load, and
therefore there is
little signal
fluctuation. The LBFD-00201801 /
NO NO No
measured RSRQ TDLBFD-00201801
load and are likely
real time. Even
when this
parameter is set to
BOTH, the eNodeB
triggers a handover
based on the
setting of the
IntraFreqHoA3Trig
Quan parameter.
For details, see
3GPP TS 36.331.
Indicates the
interval between
periodic
measurement
reports that are
sent after an intra-
frequency handover
LBFD-00201801 /
is triggered. The
TDLBFD-00201801
value of this NO NO No
LOFD-001032 /
parameter is also
TDLOFD-001032
used as the interval
between A3-related
inter-frequency
measurement
reports.
For details, see
3GPP TS 36.331.
Indicates the
quantity to be
included in the
measurement
report for inter-
frequency handover
events. Based on
the parameter
value, the eNodeB
instructs a UE to
report the
measured RSRP
value, RSRQ value,
LBFD-00201802 /
or both values. The
TDLBFD-00201802
measured RSRP NO NO No
LOFD-001032 /
values are stable
TDLOFD-001032
and vary little with
the load, and
therefore there is
little signal
fluctuation. The
measured RSRQ
load and are likely
real time. For
details, see 3GPP
TS 36.331.
Indicates the
interval at which
periodical
reports are sent TDLBFD-00201802
NO NO No
after an inter- LOFD-001032 /
frequency handover TDLOFD-001032
event is triggered.
For details, see
3GPP TS 36.331.
Indicates the
quantity used in the
evaluation for inter-
frequency
measurement event
A1 or A2. The
quantity can be
RSRP, RSRQ, or
both. The measured
RSRP values are
LBFD-00201802 /
with the load, and NO NO No
TDLBFD-00201802
therefore there is
little signal
fluctuation. The
measured RSRQ
load and are likely
real time. For
details, see 3GPP
TS 36.331.
Indicates the
triggering quantity
for frequency-
frequency
measurement
events A1 and A2.
The quantity can be
either RSRP or
RSRQ. The
measured RSRP
values are stable,
LBFD-00201802 /
varying little with NO NO No
TDLBFD-00201802
the load, and
therefore there is
little signal
fluctuation. The
measured RSRQ
load and are likely
real time. For
details, see 3GPP
TS 36.331.
Indicates the
triggering quantity
for frequency-
LBFD-00201802 /
priority- and load- NO NO No
TDLBFD-00201802
based inter-
frequency handover
event A4.
Indicates the local
YES YES No
cell within a BS.
UTRAN. When CS
fallback to UTRAN
is applicable, this
parameter is set for
UEs and used in
the evaluation of
whether to trigger
event B1. When
detecting that the
least one UTRAN
cell meets the
entering condition,
the UE does not
send a
measurement
report to the
eNodeB
LOFD-001033 /
immediately. NO NO No
TDLOFD-001033
Instead, the UE
sends a report only
when the signal
meets the entering
parameter helps
decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers, and the
number of wrong
handovers, and
thus helps prevent
GERAN. When CS
fallback to GERAN
is applicable, this
UEs and used in
the evaluation of
whether to trigger
event B1. When
detecting that the
least one GERAN
cell meets the
entering condition,
the UE does not
send a
measurement
report to the
eNodeB
LOFD-001034 /
immediately. NO NO No
TDLOFD-001034
Instead, the UE
sends a report only
when the signal
meets the entering
parameter helps
decrease the
number of
occasionally
triggered event
reports, the
average number of
handovers, and the
number of wrong
handovers, and
thus helps prevent
CDMA2000. When
CS fallback to
CDMA2000 is
applicable, this
UEs and used in
the evaluation of
whether to trigger
event B1. When
detecting that the
least one
CDMA2000 cell
meets the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately.
Instead, the UE
sends a report only
when the signal
meets the entering
parameter helps
reduce the number
of occasionally
triggered event
reports, the
average number of
handovers, and the
number of wrong
handovers, and
hence helps
prevent
Indicates the RSCP
threshold for event
B1, which is used in
CS fallback to
UTRAN. When CS
fallback to UTRAN
is applicable, this
UEs and used in
the evaluation
about whether to
trigger event B1.
This parameter
indicates the RSCP
requirement for the
LOFD-001033 /
UTRAN cells to be NO NO No
TDLOFD-001033
included in the
measurement
report. A UE sends
a measurement
report related to
event B1 to the
eNodeB when the
RSCP in at least
one UTRAN cell
exceeds this
threshold and other
triggering
conditions are met.
For details, see
3GPP TS 36.331.
UTRAN. When CS
fallback to UTRAN
is required, this
UEs and used in
the evaluation
about whether to
trigger event B1.
This parameter
indicates the Ec/No
requirement for the
UTRAN cells to be
included in the
measurement
report. A UE sends
a measurement
report related to
event B1 to the
eNodeB when the LOFD-001033 /
NO NO No
Ec/No in at least TDLOFD-001033
one UTRAN cell
exceeds this
threshold and other
triggering
conditions are met.
For a cell with large
signal fading
variance, set this
parameter to a
large value to
prevent
unnecessary
handovers. For a
cell with small
signal fading
variance, set this
parameter to a
small value to
Indicates the RSSI
threshold for event
B1 that is used in
CS fallback to
GERAN. A UE
sends a
measurement
report related to
event B1 to the LOFD-001034 /
NO NO No
eNodeB when the TDLOFD-001034
RSSI in at least one
GERAN cell
exceeds this
threshold and other
triggering
conditions are met.
For details, see
3GPP TS 36.331.
Indicates the pilot
strength threshold
related to event B1,
which is used in CS
fallback to
CDMA2000. A UE
sends a
measurement
report related to
event B1 to the
eNodeB when the
pilot strength in at
least one
CDMA2000 cell
exceeds this
threshold and other
triggering
conditions are met.
For details, see
3GPP TS 36.331.
Indicates the local

YES YES No
cell within a BS.

to configure the TDLBFD-001001
NO NO No
access barring LBFD-002009 /
information. TDLBFD-002009
UEs of access
classes 0 to 9 or
UEs without USIMs
are allowed to
initiate emergency
calls only if access
class 10 is not
barred.
If both access class LBFD-002028 /
NO NO No
10 and an access TDLBFD-002028
class in the range
of 11 to 15 are
barred, UEs of the
access class in the
range of 11 to 15
are not allowed to
initiate emergency
calls.
Indicates whether
to configure the LBFD-001001 /
access barring TDLBFD-001001
NO NO No
information for LBFD-002009 /
mobile-originated TDLBFD-002009
calls.
Indicates the
access probability
factor for mobile-
originated calls. A
mobile-originated
call is granted
LBFD-001001 /
access if the
TDLBFD-001001
random number NO NO No
LBFD-002009 /
generated by the
TDLBFD-002009
UE is smaller than
this access
probability factor;
otherwise, the
access request is
rejected.
Indicates the
LBFD-001001 /
average access
TDLBFD-001001
barring duration for NO NO No
LBFD-002009 /
mobile-originated
TDLBFD-002009
calls.
Indicates the
mobile-originated
call barring status
of access class 11,
indicating whether
UEs of access class
11 can initiate
mobile-originated
calls.
If this parameter is LBFD-001001 /
set to TDLBFD-001001
NO NO No
BOOLEAN_TRUE, LBFD-002009 /
UEs of access class TDLBFD-002009
11 cannot initiate
mobile-originated
calls. If this
parameter is set to
BOOLEAN_FALSE,
UEs of access class
11 can initiate
mobile-originated
calls.
Indicates the
mobile-originated
call barring status
of access class 12,
indicating whether
UEs of access class
12 can initiate
mobile-originated
calls.
NO NO No
12 cannot initiate
mobile-originated
calls. If this
parameter is set to
BOOLEAN_FALSE,
UEs of access class
12 can initiate
mobile-originated
calls.
Indicates the
mobile-originated
call barring status
of access class 13,
indicating whether
UEs of access class
13 can initiate
mobile-originated
calls.
NO NO No
13 cannot initiate
mobile-originated
calls. If this
parameter is set to
BOOLEAN_FALSE,
UEs of access class
13 can initiate
mobile-originated
calls.
Indicates the
mobile-originated
call barring status
of access class 14,
indicating whether
UEs of access class
14 can initiate
mobile-originated
calls.
NO NO No
14 cannot initiate
mobile-originated
calls. If this
parameter is set to
BOOLEAN_FALSE,
UEs of access class
14 can initiate
mobile-originated
calls.
Indicates the
mobile-originated
call barring status
of access class 15,
indicating whether
UEs of access class
15 can initiate
mobile-originated
calls.
NO NO No
15 cannot initiate
mobile-originated
calls. If this
parameter is set to
BOOLEAN_FALSE,
UEs of access class
15 can initiate
mobile-originated
calls.
Indicates whether
LBFD-001001 /
to configure the
TDLBFD-001001
access barring NO NO No
LBFD-002009 /
information for
TDLBFD-002009
signaling.
Indicates the
access probability
factor for signaling.
Signaling from a UE
is granted access if
LBFD-001001 /
the random number
TDLBFD-001001
generated by the NO NO No
LBFD-002009 /
UE is smaller than
TDLBFD-002009
this access
probability factor;
otherwise, the
access request is
rejected.

average access TDLBFD-001001
NO NO No
barring duration for LBFD-002009 /
signaling. TDLBFD-002009
Indicates the
signaling barring
status of access
class 11, indicating
whether UEs of
access class 11 can
initiate signaling
access.
NO NO No
11 cannot initiate
signaling access. If
this parameter is
set to
BOOLEAN_FALSE,
UEs of access class
11 can initiate
signaling access.
Indicates the
signaling barring
status of access
whether UEs of
access class 12
can initiate
signaling access.
NO NO No
12 cannot initiate
this parameter is
set to
BOOLEAN_FALSE,
UEs of access class
12 can initiate
signaling access.
Indicates the
signaling barring
status of access
whether UEs of
access class 13
can initiate
signaling access.
NO NO No
13 cannot initiate
this parameter is
set to
BOOLEAN_FALSE,
UEs of access class
13 can initiate
signaling access.
Indicates the
signaling barring
status of access
whether UEs of
access class 14
can initiate
signaling access.
NO NO No
14 cannot initiate
this parameter is
set to
BOOLEAN_FALSE,
UEs of access class
14 can initiate
signaling access.
Indicates the
signaling barring
status of access
whether UEs of
access class 15
can initiate
signaling access.
NO NO No
15 cannot initiate
this parameter is
set to
BOOLEAN_FALSE,
UEs of access class
15 can initiate
signaling access.
Indicates the local

YES YES No
cell within a BS.
Indicates whether
the cell is barred. If LBFD-001001 /
the cell is barred, TDLBFD-001001
the UE cannot LBFD-002009 /
camp on the TDLBFD-002009
NO NO No
serving cell. During LBFD-00201803 /
cell reselection, the TDLBFD-00201803
serving cell is not LOFD-002012 /
selected as a TDLOFD-002012
candidate cell.
If the cell is
reserved, whether a
UE can access the
cell depends on the
access class of the
UE and its serving
PLMN. Details are
described as
follows: (1) A UE of
access class 11 or
15 treats the cell as
a candidate if the
UE is served by its
home PLMN
(HPLMN) or
equivalent home
PLMN (EHPLMN); LBFD-001001 /
(2) A UE of access TDLBFD-001001
class 11 or 15 treats LBFD-002009 /
NO NO No
the cell as a barred TDLBFD-002009
cell if it is not LBFD-00201803 /
served by its TDLBFD-00201803
HPLMN or
EHPLMN; (3) A UE
of an access class
within the two
ranges of 0-9 and
12-14 treats the cell
as a barred cell. In
this version, the
parameter still
supports setting
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
Indicates whether
the cell can initiate
the intra-frequency
cell reselection
when the cell is
barred. LBFD-001001 /
NOT_ALLOWED TDLBFD-001001
means that the UE LBFD-002009 /
NO NO No
cannot initiate the TDLBFD-002009
intra-frequency cell LBFD-00201803 /
reselection, and TDLBFD-00201803
ALLOWED means
that the UE can
initiate the intra-
frequency cell
reselection.
broadcast mode of
the cell. In normal
mode, the PLMN ID
of the primary
operator ranks the
top of the PLMN ID
list in the system
information. In
round robin mode,
the sequence of
PLMN IDs in the list
is changed at an
interval specified by
the RoundPeriod
parameter. If certain
cells on the live LBFD-001001 /
network are in RAN TDLBFD-001001
sharing with LBFD-002009 /
common carriers TDLBFD-002009
NO NO No
mode and at least LBFD-00201803 /
one cell uses the TDLBFD-00201803
round Robin mode, LOFD-001036 /
NBSLTEPLMNRou TDLOFD-001036
ndSwitch under the
RanSharingAnrSwit
ch parameter must
be turned on for
eNodeBs whose
cells are configured
as neighboring cells
for the local cell.
Otherwise, UEs
may fail to be
handed over from
an neighboring cell
to an ANR-
established cell that
is in round Robin
LBFD-001001 /
TDLBFD-001001
LBFD-002009 /
Indicates the
TDLBFD-002009
changing period of NO NO No
LBFD-00201803 /
cell PLMN.
TDLBFD-00201803
LOFD-001036 /
TDLOFD-001036
Indicates the local

YES YES No
cell within a BS.
LBFD-001001 /
Indicates the
TDLBFD-001001
tracking area
LBFD-002009 /
identity of the cell,
TDLBFD-002009
which uniquely YES YES No
LBFD-00201803 /
identifies an
TDLBFD-00201803
operator within a
LOFD-001036 /
cell.
TDLOFD-001036
Indicates whether
the cell is reserved
for operator use.
set to
CELL_RESERVED
_FOR_OP, the cell
is reserved for
operator use. UEs
of AC11 or AC15 in
their HPLMN or
EHPLMN can
consider this cell as
a candidate cell for
cell selection or
reselection. UEs of
LBFD-001001 /
AC11 or AC15
TDLBFD-001001
outside their
LBFD-002009 /
HPLMN/EHPLMN NO NO No
TDLBFD-002009
and UEs of AC0-
LBFD-00201803 /
9/AC12-14 consider
TDLBFD-00201803
this cell as a barred
cell during cell
selection or
reselection.
set to
CELL_NOT_RESE
RVED_FOR_OP,
the cell is not
reserved for
operator use. All
UEs can consider
this cell as a
candidate cell for
cell selection or
reselection.
Indicates the
percentage of RBs
occupied by the
operator on the
PUSCH when RAN
sharing is enabled
at the eNodeB and
LBFD-001001 /
the cell-level switch
TDLBFD-001001
of RAN sharing is
LBFD-002009 /
turned on. When
TDLBFD-002009
the data volume is NO NO No
LBFD-00201803 /
sufficiently large,
TDLBFD-00201803
the percentage of
LOFD-001036 /
RBs occupied by
TDLOFD-001036
each operator will
reach the preset
value. Modifications
on this parameter
affect operators'
percentages of
RBs.
Indicates the
percentage of RBs
occupied by the
operator on the
PDSCH when RAN
sharing is enabled
at the eNodeB and
LBFD-001001 /
the cell-level switch
TDLBFD-001001
of RAN sharing is
LBFD-002009 /
turned on. When
TDLBFD-002009
the data volume is NO NO No
LBFD-00201803 /
sufficiently large,
TDLBFD-00201803
the percentage of
LOFD-001036 /
RBs occupied by
TDLOFD-001036
each operator will
reach the preset
value. Modifications
on this parameter
affect operators'
percentages of
RBs.
Indicates the
operator index that
is broadcast in the NO NO Yes None
cell system
information.
Indicates the local
YES YES No
cell within a BS.
Indicates the
hysteresis for cell
reselection when
RSRP values are
used in the
evaluation. This
parameter must be
set based on the
slow fading
characteristic of the
LBFD-001001 /
area covered by the
TDLBFD-001001
cell. The greater the
LBFD-002009 /
slow fading NO NO No
TDLBFD-002009
variance is, the
LBFD-00201803 /
larger the value of
TDLBFD-00201803
this parameter must
be set to. A larger
value of the
hysteresis results in
a larger boundary
of the serving cell
and a higher
probability of cell
reselection to
neighboring cells.
LBFD-001001 /
Indicates whether
TDLBFD-001001
to set the
LBFD-002009 /
parameters related NO NO No
TDLBFD-002009
to speed-dependent
LBFD-00201803 /
cell reselection.
TDLBFD-00201803
Indicates the
duration in which
the mobility status
of the UE is
evaluated. This
parameter is one of
the key parameters
LBFD-001001 /
in deciding on the
TDLBFD-001001
UE mobility. A
LBFD-002009 /
smaller value of this NO NO No
TDLBFD-002009
parameter may lead
LBFD-00201803 /
to more frequent
TDLBFD-00201803
switching among
mobility status and
lower decision
accuracy. A larger
value of this
parameter leads to
the opposite effect.
Indicates the extra

duration required in
the evaluation
before the UE can
enter the normal-
mobility state. This
parameter can
prevent UEs from
frequently switching
from the high- or
medium-mobility
state to the normal-
mobility state, and LBFD-001001 /
is one of the key TDLBFD-001001
parameters in LBFD-002009 /
NO NO No
deciding on the UE TDLBFD-002009
mobility. A larger LBFD-00201803 /
value of this TDLBFD-00201803
parameter leads to
a lower probability
of transition from
the high- or
medium-mobility
state to the normal-
mobility state but
higher decision
accuracy. A smaller
value of this
parameter leads to
Indicates the
threshold for a UE
to enter the medium
mobility state.
Based on the
number of cell
reselections, this
parameter is one of
the key parameters
in determining the
mobility state of the
UE. During the UE
mobility evaluation,
if the number of
reselections is LBFD-001001 /
above or equal to TDLBFD-001001
the value of this LBFD-002009 /
NO NO No
parameter and TDLBFD-002009
below than the LBFD-00201803 /
value of TDLBFD-00201803
NCellChangeHigh,
the UE enters the
medium mobility
state.
A smaller value of
this parameter
results in a higher
probability of a UE
entering the
medium mobility
state. A larger value
of this parameter
leads to a lower
probability.
Indicates the
threshold for a UE
to enter the high
mobility state.
Based on the
number of cell
reselections, this
parameter is one of
the key parameters
in determining the
mobility state of the
UE. During the UE
LBFD-001001 /
mobility evaluation,
TDLBFD-001001
if the number of cell
LBFD-002009 /
reselections is NO NO No
TDLBFD-002009
above or equal to
LBFD-00201803 /
the value of this
TDLBFD-00201803
parameter, the UE
enters the high
mobility state.
A smaller value of
this parameter
results in a higher
probability of a UE
entering the high
mobility state. A
parameter leads to
Indicates the
scaling factor (or
known as additional
hysteresis) applied
to Qhyst for
medium-mobility
UEs.
For example, the LBFD-001001 /
value TDLBFD-001001
DB_6_Q_HYST_SF LBFD-002009 /
NO NO No
_MEDIUM indicates TDLBFD-002009
-6 dB additional LBFD-00201803 /
hysteresis applied TDLBFD-00201803
to Qhyst for
medium-mobility
UEs, and
DB_4_Q_HYST_SF
_MEDIUM indicates
-4 dB additional
hysteresis.
Indicates the
scaling factor (or
known as additional
hysteresis) applied
to Qhyst for high-
mobility UEs.
For example, the LBFD-001001 /
value TDLBFD-001001
DB_6_Q_HYST_SF LBFD-002009 /
NO NO No
_HIGH indicates -6 TDLBFD-002009
dB additional LBFD-00201803 /
hysteresis applied TDLBFD-00201803
to Qhyst for high-
mobility UEs, and
DB_4_Q_HYST_SF
_HIGH indicates -4
dB additional
hysteresis.
Indicates whether
LBFD-001001 /
to set the
TDLBFD-001001
measurement
LBFD-002009 /
triggering threshold NO NO No
TDLBFD-002009
for reselection to
LBFD-00201803 /
inter-frequency or
TDLBFD-00201803
inter-RAT cells.
Indicates the
measurement
triggering threshold
for reselection to
inter-frequency or
inter-RAT cells. The
step is 2 dB.
If the cell
reselection priority
of a frequency or
RAT is higher than
that of the serving
frequency, the UEs
always start inter-
frequency or inter-
RAT
LBFD-001001 /
measurements.
TDLBFD-001001
If the cell
LBFD-002009 /
reselection priority NO NO No
TDLBFD-002009
of a frequency is
LBFD-00201803 /
lower than or equal
TDLBFD-00201803
to that of the
serving frequency
or if the cell
of an RAT is lower
than that of the
serving frequency,
the UEs start inter-
frequency or inter-
RAT measurements
only when the value
of Cell selection RX
level value (dB) is
lower than or equal
to the value of this
parameter.
Indicates the
threshold used in
the evaluation of
reselection to a cell
on a lower priority
E-UTRAN
frequency or on an
inter-RAT
frequency. Cell
reselection to a cell
LBFD-001001 /
on a lower priority
TDLBFD-001001
E-UTRAN
LBFD-002009 /
frequency or on an NO NO No
TDLBFD-002009
inter-RAT frequency
LBFD-00201803 /
is performed if no
TDLBFD-00201803
cell on the serving
frequency or on a
higher priority E-
UTRAN frequency
fulfills criteria 1 for
inter-frequency and
inter-RAT
reselections. For
details, see 3GPP
TS 36.304.
Indicates the cell

of the serving
frequency. 0
priority. The value
of this parameter
LBFD-001001 /
must be determined
TDLBFD-001001
together with the
LBFD-002009 /
priorities of other NO NO No
TDLBFD-002009
frequencies during
LBFD-00201803 /
the network
TDLBFD-00201803
planning.
Frequencies used
for different RATs
must be assigned
different cell
reselection
priorities.
Indicates the
minimum required
RX level used in
intra-frequency E-
UTRAN cell
LBFD-001001 /
reselection, which
TDLBFD-001001
corresponds to the
LBFD-002009 /
IE q-RxLevMin in NO NO No
TDLBFD-002009
SIB3. This value is
LBFD-00201803 /
included in criteria
TDLBFD-00201803
R and used in the
evaluation of cell
reselection. For
details, see 3GPP
TS 36.304.
Indicates whether
to configure the
maximum TX power
of the UE in the
intra-frequency
neighboring cell. LBFD-001001 /
When the TDLBFD-001001
NO NO No
CFG, the maximum TDLBFD-002009
TX power of the UE LBFD-00201803 /
is configured. When TDLBFD-00201803
to NOT_CFG, the
maximum TX power
of the UE is not
configured.
Indicates the
maximum TX power
of the UE in the
cell. If this LBFD-001001 /
parameter is not TDLBFD-001001
specified in SIB3, LBFD-002009 /
NO NO No
the maximum TX TDLBFD-002009
power that the UE LBFD-00201803 /
can physically TDLBFD-00201803
achieve is used as
this maximum TX
power.
Indicates whether
LBFD-001001 /
to set the
TDLBFD-001001
measurement
LBFD-002009 /
triggering threshold NO NO No
TDLBFD-002009
for reselection to
LBFD-00201803 /
intra-frequency
TDLBFD-00201803
cells.
Indicates the
measurement
triggering threshold
for reselection to
intra-frequency
cells. The step is 2 LBFD-001001 /
dB. TDLBFD-001001
The UEs start intra- LBFD-002009 /
NO NO No
frequency TDLBFD-002009
measurements only LBFD-00201803 /
if the value of Cell TDLBFD-00201803
selection RX level
value (dB) is lower
than or equal to the
value of this
parameter.
LBFD-001001 /
Indicates whether TDLBFD-001001
to set the LBFD-002009 /
NO NO No
measurement TDLBFD-002009
bandwidth. LBFD-00201803 /
TDLBFD-00201803
Indicates the
measurement
bandwidth on the
serving frequency
on which the UE
camps. It is used in
intra-frequency LBFD-001001 /
measurements for TDLBFD-001001
cell reselection and LBFD-002009 /
NO NO No
those by UEs in TDLBFD-002009
RRC_CONNECTE LBFD-00201803 /
D mode. This TDLBFD-00201803
parameter is
optional; if it is not
set, the downlink
bandwidth of the
serving cell is used
by default.
Indicates the cell

reselection duration
of the E-UTRAN.
When the signal
quality of the new
cell is better than
the serving cell all
the time and the UE
stays in the current
serving cell for
more than 1s, the
UE is initiating cell
reselection request
to the new cell. The LBFD-001001 /
smaller the TDLBFD-001001
parameter is, the LBFD-002009 /
NO NO No
easier the cell TDLBFD-002009
reselection from the LBFD-00201803 /
serving cell is TDLBFD-00201803
triggered, and the
more possibly that
the pingpong
reselection occurs.
The bigger the
parameter is, the
more difficult the
cell reselection from
the serving cell is
triggered, and the
less possibly that
the pingpong
reselection occurs.
to set the scaling TDLBFD-001001
parameters for LBFD-002009 /
NO NO No
speed-dependent TDLBFD-002009
cell reselection LBFD-00201803 /
within E-UTRAN. TDLBFD-00201803
Indicates the
scaling factor
applied to
TReselEutra for
medium-mobility LBFD-001001 /
UEs. The actual TDLBFD-001001
duration of cell LBFD-002009 /
NO NO No
reselection for TDLBFD-002009
medium-mobility LBFD-00201803 /
UEs to E-UTRAN is TDLBFD-00201803
equal to the product
of TReselEutra and
TReselEutranSfMe
dium.
Indicates the
scaling factor
applied to
TReselEutran for
LBFD-001001 /
high-mobility UEs.
TDLBFD-001001
The actual duration
LBFD-002009 /
of cell reselection of NO NO No
TDLBFD-002009
high-mobility UEs to
LBFD-00201803 /
E-UTRAN is equal
TDLBFD-00201803
to TReselEutran
multiplied by
TReselEutranSfHig
h.
Indicates the
information related
to MBSFN and TDD
UL/DL
configurations of
intra-frequency
neighboring cells of
the serving cell.
The value 00
indicates that some
neighboring cells
have the same
MBSFN subframe
configuration as the
serving cell.
The value 01
indicates that none LBFD-001001 /
of the neighboring TDLBFD-001001
cells is configured LBFD-002009 /
NO NO No
with MBSFN TDLBFD-002009
subframes. LBFD-00201803 /
The value 10 TDLBFD-00201803
indicates that the
MBSFN subframe
configurations of all
neighboring cells
are the same as or
subsets of that of
the serving cell.
The value 11
indicates that some
neighboring cells
have different UL-
DL configurations
from the serving
TDD cell.
For details, see
3GPP TS 36.331.
Indicates whether
the intra-frequency
neighboring cells
are configured with
the 2TX antenna.
Set this parameter
to TRUE when all LBFD-001001 /
the intra-frequency TDLBFD-001001
neighboring cells LBFD-002009 /
NO NO No
are configured with TDLBFD-002009
the 2TX antenna. LBFD-00201803 /
Set this parameter TDLBFD-00201803
to FALSE when one
of the intra-
frequency
neighboring cells is
not configured with
the 2TX antenna.
Indicates the RSRQ
threshold for
starting intra-
frequency
measurements. It
LBFD-002009 /
determines the
TDLBFD-002009
probability of NO NO No
LBFD-00201803 /
triggering cell
TDLBFD-00201803
reselection to an
intra-frequency
neighboring cell.
For details, see
3GPP TS 36.304.
Indicates the RSRQ

threshold for
starting inter-
frequency or inter-
RAT
measurements. It
LBFD-002009 /
determines the
TDLBFD-002009
LBFD-00201803 /
triggering cell
TDLBFD-00201803
reselection to an
inter-frequency or
inter-RAT
neighboring cell.
For details, see
3GPP TS 36.304.
Indicates whether
to set the RSRQ LBFD-002009 /
threshold for TDLBFD-002009
NO NO No
reselection to cells LBFD-00201803 /
on lower-priority TDLBFD-00201803
frequencies.
Indicates the RSRQ

threshold for cell
reselection to cells
on lower-priority
frequencies. It
determines the
LBFD-002009 /
probability of
TDLBFD-002009
triggering cell NO NO No
LBFD-00201803 /
reselection to inter-
TDLBFD-00201803
frequency or inter-
RAT neighboring
cells on lower-
priority frequencies.
For details, see
3GPP TS 36.304.
Indicates whether
to set the RX level
of an intra-
LBFD-002009 /
frequency
TDLBFD-002009
neighboring cell, NO NO No
LBFD-00201803 /
which is required for
TDLBFD-00201803
it to become a
candidate for cell
reselection.
Indicates the
minimum required
RX signal quality
used in intra-
frequency E-
UTRAN cell
reselection, which LBFD-002009 /
corresponds to the TDLBFD-002009
NO NO No
IE q-QualMin in LBFD-00201803 /
SIB3. This value is TDLBFD-00201803
R and used in the
evaluation of cell
reselection. For
details, see 3GPP
TS 36.304.
Indicates the local

YES YES No
cell within a BS.

to configure the TDLBFD-001001
CDMA2000 system LBFD-002009 /
NO NO No
time information. TDLBFD-002009
For details, see LBFD-00201803 /
3GPP TS 36.331. TDLBFD-00201803
Indicates the
network
synchronization
status. If this
parameter is set to
BOOLEAN_TRUE,
the E-UTRAN and
the CDMA2000
RAN are LBFD-001001
synchronized NO NO No LBFD-002009
without drifts. If this LBFD-00201803
parameter is set to
BOOLEAN_FALSE,
the E-UTRAN and
the CDMA2000
RAN are not
synchronized. For
details, see 3GPP
TS 36.331.
Indicates whether
to set the search
window size. If this
parameter is set to
CFG, the cell is LBFD-001001 /
configured with the TDLBFD-001001
search window. If LBFD-002009 /
NO NO No
the parameter is set TDLBFD-002009
to NOT_CFG, the LBFD-00201803 /
cell is not TDLBFD-00201803
configured with the
search window. For
details, see 3GPP
TS 36.331.
Indicates the size of

the CDMA2000
LBFD-001001 /
search window, and
TDLBFD-001001
can be used to
LBFD-002009 /
assist in searching NO NO No
TDLBFD-002009
for the neighboring
LBFD-00201803 /
pilots. For details,
TDLBFD-00201803
see 3GPP TS
36.331.
Indicates whether
to set the HRPD
parameters. If this
CFG, the cell is TDLBFD-001001
configured with the LBFD-002009 /
NO NO No
HRPD parameters. TDLBFD-002009
If the parameter is LBFD-00201803 /
set to NOT_CFG, TDLBFD-00201803
the cell is not
configured with the
HRPD parameters.
Indicates whether
to set the
parameters related
to cell reselection to
CDMA2000 HRPD.
If the parameter is
set to CFG, the cell
LBFD-001001 /
is configured with
TDLBFD-001001
the parameters
LBFD-002009 /
related to cell NO NO No
TDLBFD-002009
reselection to
LBFD-00201803 /
CDMA2000 HRPD.
TDLBFD-00201803
If the parameter is
set to NOT_CFG,
the cell is not
configured with the
parameters related
CDMA2000 HRPD.
Indicates whether
pre-registration with
CDMA2000 HRPD
is allowed when the
UE does not have a
valid pre-
registration. If the
LBFD-001001 /
parameter is set to
TDLBFD-001001
BOOLEAN_TRUE,
LBFD-002009 /
the UE is allowed to NO NO No
TDLBFD-002009
perform the pre-
LBFD-00201803 /
registration. If the
TDLBFD-00201803
parameter is set to
BOOLEAN_FALSE,
the UE is not
allowed to perform
the pre-registration.
For details, see
3GPP TS 36.331.
Indicates the ID of
the pre-registration
CDMA2000 HRPD
zone. This
parameter is used
to control the re- LBFD-001001
registration of the NO NO No LBFD-002009
UE and is valid only LBFD-00201803
when pre-
registration is
allowed. For details,
see 3GPP TS
36.331.
Indicates whether
secondary pre-
registration zone ID
0 needs to be set.
The value CFG
indicates that LBFD-001001 /
secondary pre- TDLBFD-001001
registration zone ID LBFD-002009 /
NO NO No
0 exists, and the TDLBFD-002009
value NOT_CFG LBFD-00201803 /
indicates that TDLBFD-00201803
secondary pre-
0 does not exist.
For details, see
3GPP TS 36.331.
Indicates secondary
LBFD-001001 /
pre-registration
TDLBFD-001001
zone ID 0. It is used
LBFD-002009 /
to control the re- NO NO No
TDLBFD-002009
registration of the
LBFD-00201803 /
UE. For details, see
TDLBFD-00201803
3GPP TS 36.331.
Indicates whether
secondary pre-
1 needs to be set.
The value CFG
indicates that LBFD-001001 /
secondary pre- TDLBFD-001001
registration zone ID LBFD-002009 /
NO NO No
1 exists, and the TDLBFD-002009
value NOT_CFG LBFD-00201803 /
indicates that TDLBFD-00201803
secondary pre-
1 does not exist.
For details, see
3GPP TS 36.331.
Indicates secondary
LBFD-001001 /
pre-registration
TDLBFD-001001
zone ID 1. It is used
LBFD-002009 /
to control the re- NO NO No
TDLBFD-002009
registration of the
LBFD-00201803 /
UE. For details, see
TDLBFD-00201803
3GPP TS 36.331.
CDMA2000 HRPD.
The UE initiates
reselection to a
CDMA2000 HRPD
cell when all the
following conditions
are met: (1) The
serving cell is
continuously lower
than its low-priority
reselection
threshold during the
time; (2) The signal
quality in the
CDMA2000 HRPD
cell is continuously LBFD-001001 /
higher than its low- TDLBFD-001001
priority reselection LBFD-002009 /
NO NO No
threshold during the TDLBFD-002009
time; and (3) The LBFD-00201803 /
UE camps on the TDLBFD-00201803
current serving cell
for more than 1s. A
smaller value of this
parameter indicates
a higher probability
of initiating cell
reselection but a
higher probability of
ping-pong
reselection. A larger
value indicates a
lower probability of
initiating cell
reselection but a
ping-pong
Indicates whether
to set the speed-
dependent scaling
parameters related
CDMA2000 HRPD.
set to CFG, the LBFD-001001 /
system supports TDLBFD-001001
the speed- LBFD-002009 /
NO NO No
dependent scaling TDLBFD-002009
parameters. If this LBFD-00201803 /
NOT_CFG, the
system does not
support the speed-
dependent scaling
parameters. For
details, see 3GPP
TS 36.331.
Indicates the
scaling factor
applied to
TReselCdmaHrpd
for high-mobility
UEs. The actual
duration of cell
reselection of high-
mobility UEs to
CDMA2000 HRPD
LBFD-001001 /
is equal to
TDLBFD-001001
TReselCdmaHrpd
LBFD-002009 /
multiplied by NO NO No
TDLBFD-002009
TReselCdmaHrpdSf
LBFD-00201803 /
High.
TDLBFD-00201803
The value
T_RESEL_SF_0DO
T25 means a
scaling factor of
0.25,
T_RESEL_SF_0DO
T5 means 0.5, and
so on. For details,
see 3GPP TS
36.331.
Indicates the
scaling factor
applied to
TReselCdmaHrpd
for medium-mobility
UEs. The actual
duration of cell
reselection of
medium-mobility
UEs to CDMA2000
LBFD-001001 /
HRPD is equal to
TDLBFD-001001
TReselCdmaHrpd
LBFD-002009 /
multiplied by NO NO No
TDLBFD-002009
TReselCdmaHrpdSf
LBFD-00201803 /
Medium.
TDLBFD-00201803
The value
T_RESEL_SF_0DO
T25 means a
scaling factor of
0.25,
T_RESEL_SF_0DO
T5 means 0.5, and
so on. For details,
see 3GPP TS
36.331.
Indicates whether
the parameters
applicable only for
interworking with
CDMA2000 1xRTT
need to be set. If
LBFD-001001 /
this parameter is
TDLBFD-001001
LBFD-002009 /
needs to be NO NO No
TDLBFD-002009
configured with the
LBFD-00201803 /
1xRTT parameters.
TDLBFD-00201803
set to NOT_CFG,
the cell does not
need to be
configured with the
1xRTT parameters.
Indicates whether
registration
parameters need to
be set for CS
fallback to
CDMA2000 1xRTT.
needs to be LBFD-001001 /
configured with the TDLBFD-001001
registration LBFD-002009 /
parameters for CS NO NO No TDLBFD-002009
fallback to LBFD-00201803 /
CDMA2000 1xRTT. TDLBFD-00201803
If this parameter is LOFD-001035
set to NOT_CFG,
the cell does not
need to be
configured with the
registration
parameters for CS
fallback to
CDMA2000 1xRTT.
LBFD-001001 /
CDMA2000 1xRTT LBFD-002009 /
system ID. For NO NO No TDLBFD-002009
details, see 3GPP LBFD-00201803 /
TS 36.331. TDLBFD-00201803
LOFD-001035
LBFD-001001 /
CDMA2000 1xRTT LBFD-002009 /
network ID. For NO NO No TDLBFD-002009
TS 36.331. TDLBFD-00201803
LOFD-001035
LBFD-001001 /
Indicates the
TDLBFD-001001
1xRTT-specific
LBFD-002009 /
multiple system ID
NO NO No TDLBFD-002009
storage is allowed.
LBFD-00201803 /
For details, see
TDLBFD-00201803
3GPP TS 36.331.
LOFD-001035
LBFD-001001 /
Indicates the
TDLBFD-001001
1xRTT-specific
LBFD-002009 /
multiple network ID
storage is allowed.
LBFD-00201803 /
For details, see
TDLBFD-00201803
3GPP TS 36.331.
LOFD-001035
LBFD-001001 /
Indicates the
TDLBFD-001001
1xRTT-specific
LBFD-002009 /
home registration is
LBFD-00201803 /
see 3GPP TS
TDLBFD-00201803
36.331.
LOFD-001035
LBFD-001001 /
Indicates the
TDLBFD-001001
1xRTT-specific SID
LBFD-002009 /
roamer registration
is allowed. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001001 /
Indicates the
TDLBFD-001001
1xRTT-specific NID
LBFD-002009 /
roamer registration
is allowed. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
1xRTT-specific TDLBFD-001001
parameter-change LBFD-002009 /
registration is NO NO No TDLBFD-002009
allowed. For details, LBFD-00201803 /
see 3GPP TS TDLBFD-00201803
36.331. LOFD-001035

power-up LBFD-002009 /
registration is NO NO No TDLBFD-002009
allowed. For details, LBFD-00201803 /
see 3GPP TS TDLBFD-00201803
36.331. LOFD-001035
LBFD-001001 /
1xRTT-specific LBFD-002009 /
registration period. NO NO No TDLBFD-002009
3GPP TS 36.331. TDLBFD-00201803
LOFD-001035
LBFD-001001 /
1xRTT-specific LBFD-002009 /
registration zone. NO NO No TDLBFD-002009
3GPP TS 36.331. TDLBFD-00201803
LOFD-001035

number of LBFD-002009 /
registration zones NO NO No TDLBFD-002009
to be retained. For LBFD-00201803 /
details, see 3GPP TDLBFD-00201803
TS 36.331. LOFD-001035
LBFD-001001 /
Indicates the length TDLBFD-001001
of the 1xRTT- LBFD-002009 /
specific zone timer. NO NO No TDLBFD-002009
3GPP TS 36.331. TDLBFD-00201803
LOFD-001035
Indicates whether
the CDMA2000
1xRTT-specific long
code state needs to
be set. If this
parameter is set to
CFG, the cell needs
to be configured
with the long code
state. If this
parameter is set to
LBFD-001001 /
NOT_CFG, the cell
TDLBFD-001001
does not need to be
LBFD-002009 /
configured with the NO NO No
TDLBFD-002009
long code state. In
LBFD-00201803 /
this version, the
TDLBFD-00201803
setting of this
parameter is still
synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Avoid using this
parameter as it will
be removed from
later versions.
Indicates the
CDMA2000 1xRTT-
specific long code
state. For details,
see 3GPP TS
36.331. In this
LBFD-001001 /
TDLBFD-001001
LBFD-002009 /
still synchronized NO NO No
TDLBFD-002009
between the M2000
LBFD-00201803 /
and the eNodeB,
TDLBFD-00201803
but it is no longer
used internally.
Avoid using this
be removed from
later versions.
Indicates whether
the parameters
applicable only for
cell reselection to
CDMA2000 1xRTT
need to be set. If
this parameter is
LBFD-001001 /
needs to be
TDLBFD-001001
configured with the
LBFD-002009 /
parameters related NO NO No
TDLBFD-002009
LBFD-00201803 /
CDMA2000 1xRTT.
TDLBFD-00201803
set to NOT_CFG,
the cell does not
need to be
configured with the
parameters related
CDMA2000 1xRTT.
duration used in cell TDLBFD-001001
reselection to LBFD-002009 /
NO NO No
CDMA2000 1xRTT. TDLBFD-002009
3GPP TS 36.331. TDLBFD-00201803
Indicates whether
speed-dependent
scaling parameters
need to be set for
cell reselection to
CDMA2000 1xRTT.
When the LBFD-001001 /
CFG, the system LBFD-002009 /
NO NO No
supports the speed- TDLBFD-002009
dependent scaling LBFD-00201803 /
parameters. When TDLBFD-00201803
to NOT_CFG, the
system does not
support the speed-
dependent scaling
parameters.
Indicates the
scaling factor
LBFD-001001 /
applicable to cell
TDLBFD-001001
reselection of
LBFD-002009 /
medium-mobility NO NO No
TDLBFD-002009
UEs to CDMA2000
LBFD-00201803 /
1xRTT. For details,
TDLBFD-00201803
see 3GPP TS
36.331.
Indicates the
scaling factor LBFD-001001 /
applicable to cell TDLBFD-001001
reselection of high- LBFD-002009 /
NO NO No
mobility UEs to TDLBFD-002009
CDMA2000 1xRTT. LBFD-00201803 /
For details, see TDLBFD-00201803
3GPP TS 36.331.
Indicates whether
LBFD-001007 /
to configure
TDLBFD-001007
CDMA2000 1xRTT
LBFD-002009 /
power-down NO NO No
TDLBFD-002009
registration. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LBFD-001007 /
Indicates whether TDLBFD-001007
to configure access LBFD-002009 /
NO NO No
class barring for TDLBFD-002009
CDMA2000 1xRTT. LBFD-00201803 /
TDLBFD-00201803
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
classes 0 to 9. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
class 10. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
class 11. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
class 12. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
class 13. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
class 14. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
LBFD-001007 /
Indicates the
TDLBFD-001007
persistence value
LBFD-002009 /
for access overload
class 15. For
LBFD-00201803 /
details, see 3GPP
TDLBFD-00201803
TS 36.331.
LOFD-001035
Indicates the
LBFD-001007 /
adjustment to the
TDLBFD-001007
access class
LBFD-002009 /
barring factor for
message
LBFD-00201803 /
transmissions. For
TDLBFD-00201803
details, see 3GPP
LOFD-001035
TS 36.331.
Indicates the
LBFD-001007 /
adjustment to the
TDLBFD-001007
access class
LBFD-002009 /
barring factor for
autonomous
LBFD-00201803 /
registrations. For
TDLBFD-00201803
details, see 3GPP
LOFD-001035
TS 36.331.
Indicates the
persistence value LBFD-001007 /
for emergency calls TDLBFD-001007
and emergency LBFD-002009 /
messages for NO NO No TDLBFD-002009
access overload LBFD-00201803 /
classes 0 to 9. For TDLBFD-00201803
details, see 3GPP LOFD-001035
TS 36.331.
Indicates the local

YES YES No
cell within a BS.
of GERAN cell
reselection. When
the signal quality of
the serving cell is
lower than the low
priority reselection
threshold all the
time and the signal
of the new cell is
higher than the low
threshold all the
time, and the UE
serving cell for
more than 1s, then LBFD-001001 /
the UE is initiating TDLBFD-001001
NO NO No
request to the new TDLBFD-002009
cell. The lower the LBFD-00201803 /
parameter is, the TDLBFD-00201803
easier it is for the
UE to initiate cell
reselection.
However, the Ping-
Pong reselection
probability is
increased. The
higher the
parameter is, the
harder it is for the
UE to initiate cell
reselection. The
Ping-Pong
reselection
probability,
however, is
Indicates whether
to set the speed-
dependent scaling
parameters related
GERAN. LBFD-001001 /
If this parameter is TDLBFD-001001
NO NO No
NOT_CFG, the
system does not
support the speed-
dependent scaling
parameters.
Indicates the
scaling factor
applied to
TReselGeran for
medium-mobility
UEs. The actual
duration of cell
reselection of
LBFD-001001 /
medium-mobility
TDLBFD-001001
UEs to GERAN is
LBFD-002009 /
equal to
TDLBFD-002009
TReselGeran NO NO No
LBFD-00201803 /
multiplied by
TDLBFD-00201803
TReselGeranSfMed
LBFD-002018 /
ium.
TDLBFD-002018
The value
T_RESEL_SF_0DO
T25 means a
scaling factor of
0.25,
T_RESEL_SF_0DO
T5 means 0.5, and
so on.
Indicates the
scaling factor
applied to
TReselGeran for
high-mobility UEs.
The actual duration
of cell reselection of LBFD-001001 /
high-mobility UEs to TDLBFD-001001
GERAN is equal to LBFD-002009 /
TReselGeran TDLBFD-002009
NO NO No
multiplied by LBFD-00201803 /
TReselGeranSfHigh TDLBFD-00201803
. The value LBFD-002018 /
T_RESEL_SF_0DO TDLBFD-002018
T25 means a
scaling factor of
0.25,
T_RESEL_SF_0DO
T5 means 0.5, and
so on.
Indicates the local

YES YES No
cell within a BS.
of UTRAN cell
reselection. When
the serving cell is
lower than the low
threshold all the
time and the signal
of the new cell is
higher than the low
threshold all the
time, and the UE
serving cell for
more than 1s, then LBFD-001001 /
the UE is initiating TDLBFD-001001
NO NO No
request to the new TDLBFD-002009
cell. The lower the LBFD-00201803 /
parameter is, the TDLBFD-00201803
easier it is for the
UE to initiate cell
reselection.
However, the Ping-
Pong reselection
probability is
increased. The
higher the
parameter is, the
harder it is for the
UE to initiate cell
reselection. The
Ping-Pong
reselection
probability,
however, is
Indicates whether
to set the speed-
dependent scaling
parameters related
UTRAN. LBFD-001001 /
NO NO No
NOT_CFG, the
system does not
support the speed-
dependent scaling
parameters.
Indicates the
scaling factor
applied to
TReselUtran for
medium-mobility
UEs. The actual
duration of cell
reselection of
LBFD-001001 /
medium-mobility
TDLBFD-001001
UEs to UTRAN is
LBFD-002009 /
equal to
TDLBFD-002009
TReselUtran NO NO No
LBFD-00201803 /
multiplied by
TDLBFD-00201803
TReselUtranSfMedi
LBFD-002018 /
um.
TDLBFD-002018
The value
T_RESEL_SF_0DO
T25 means a
scaling factor of
0.25,
T_RESEL_SF_0DO
T5 means 0.5, and
so on.
Indicates the
scaling factor
applied to
TReselUtran for
high-mobility UEs.
The actual duration
of cell reselection of LBFD-001001 /
high-mobility UEs to TDLBFD-001001
UTRAN is equal to LBFD-002009 /
TReselUtran TDLBFD-002009
NO NO No
multiplied by LBFD-00201803 /
TReselUtranSfHigh. TDLBFD-00201803
The value LBFD-002018 /
T_RESEL_SF_0DO TDLBFD-002018
T25 means a
scaling factor of
0.25,
T_RESEL_SF_0DO
T5 means 0.5, and
so on.
Indicates the local
YES YES No
cell within a BS.
Indicates the
minimum required
RX level for the cell
to become a
candidate for cell
LBFD-001001 /
selection, which
TDLBFD-001001
corresponds to the
LBFD-002009 /
IE q-RxLevMin in NO NO No
TDLBFD-002009
SIB1. This value is
LBFD-00201803 /
TDLBFD-00201803
S and used in the
evaluation of cell
selection. For
details, see 3GPP
TS 36.304.

to the minimum
required RX level.
This value is
S and used in the
evaluation of cell
selection. This
LBFD-001001 /
parameter is valid
TDLBFD-001001
only when the cell
LBFD-002009 /
selection is NO NO No
TDLBFD-002009
triggered by
LBFD-00201803 /
periodic searches
TDLBFD-00201803
for higher-priority
PLMNs and the UE
is served by a
Visited Public Land
Mobile Network
(VPLMN). For
details, see 3GPP
TS 36.304.
Indicates the
minimum required
RX signal quality for
the cell to become
a candidate for cell
selection, which
LBFD-002009 /
corresponds to the
TDLBFD-002009
IE q-QualMin in NO NO No
LBFD-00201803 /
SIB1. This value is
TDLBFD-00201803
S and used in the
evaluation of cell
selection. For
details, see 3GPP
TS 36.304.
Indicates whether
to set the offset to
the minimum
required RX level
for the cell. If this LBFD-002009 /
NO NO No
CFG, the offset is LBFD-00201803 /
required. If this TDLBFD-00201803
parameter is set to
NOT_CFG, the
offset does not
need to be set.

to the minimum
required RX level
for the cell. It is
S and used in the
evaluation of cell
selection. This
parameter is
LBFD-002009 /
required only when
TDLBFD-002009
the cell selection is NO NO No
LBFD-00201803 /
triggered by
TDLBFD-00201803
periodic searches
for higher-priority
PLMNs and the UE
is served by a
Visited Public Land
Mobile Network
(VPLMN). For
details, see 3GPP
TS 36.304.
Indicates the local
YES YES No
cell within a BS.
Indicates whether
the mapping from
SIBs to SI
messages is
enabled.If it is
disabled, a fixed
configuration is
used for the
mapping from SIBs LBFD-001001 /
to SI messages and TDLBFD-001001
NO NO No
the SI window size. LBFD-002009 /
If it is enabled, the TDLBFD-002009
mapping from SIBs
to SI messages and
the SI window size
are determined
based on the
transmission period,
quantity, and data
traffic of SIBs.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
information block NO NO No
LBFD-002009 /
type 2 (SIB2). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 3 (SIB3). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 4 (SIB4). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 5 (SIB5). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 6 (SIB6). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 7 (SIB7). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 8 (SIB8). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 10 (SIB10).
TDLBFD-002009
For details, see
3GPP TS 36.331.
Indicates the
transmission period
LBFD-001001 /
for system
TDLBFD-001001
LBFD-002009 /
type 11 (SIB11). For
TDLBFD-002009
details, see 3GPP
TS 36.331.
Indicates the
duration of the
LBFD-001001 /
primary notification
TDLBFD-001001
(PN) broadcast for NO NO No
LBFD-002009 /
the Earthquake and
TDLBFD-002009
Tsunami Warning
System (ETWS).
of processing
repeated secondary
notification (SN)
broadcast for the
Earthquake and
Tsunami Warning
System (ETWS). A
repeated SN is a
second SN that has
the same IEs
Message Identifier
and Serial Number LBFD-001001 /
as those in the first TDLBFD-001001
NO NO No
SN. The value LBFD-002009 /
MERGE indicates TDLBFD-002009
that the cell stops
broadcasting the
first SN and then
broadcasts the
second SN. The
value DISCARD
indicates that the
cell ignores the
second SN and
continues
broadcasting the
first SN.
of processing
repeated primary
notification (PN)
broadcast for the
Earthquake and
Tsunami Warning
System (ETWS). A
repeated PN is a
second PN that has
the same IEs
Message Identifier
and Serial Number LBFD-001001 /
as those in the first TDLBFD-001001
NO NO No
PN. The value LBFD-002009 /
MERGE indicates TDLBFD-002009
that the cell stops
broadcasting the
first PN and then
broadcasts the
second PN. The
value DISCARD
indicates that the
cell ignores the
second PN and
continues
broadcasting the
first PN.
Indicates the local

YES YES No
cell within a BS.
Indicates the
LBFD-001001 /
compensation
TDLBFD-001001
factor for path loss.
LBFD-002009 /
It is used in UL NO NO No
TDLBFD-002009
power control. For
LBFD-002026 /
details, see 3GPP
TDLBFD-002026
TS 36.213.
Indicates the target

UE transmit power
for the PUCCH
LBFD-001001 /
expected by the
TDLBFD-001001
eNodeB on
LBFD-002009 /
condition that NO NO No
TDLBFD-002009
normal
LBFD-002026 /
demodulation can
TDLBFD-002026
be performed. For
details, see 3GPP
TS 36.213.
Indicates the
LBFD-001001 /
nominal P0 value of
TDLBFD-001001
the PUSCH. It is
LBFD-002009 /
used in UL power NO NO No
TDLBFD-002009
control. For details,
LBFD-002026 /
see 3GPP TS
TDLBFD-002026
36.213.
Indicates the Delta LBFD-001001 /

value TDLBFD-001001
corresponding to LBFD-002009 /
NO NO No
PUCCH format 1. TDLBFD-002009
3GPP TS 36.213. TDLBFD-002026

value TDLBFD-001001
NO NO No
PUCCH format 1b. TDLBFD-002009
3GPP TS 36.213. TDLBFD-002026

value TDLBFD-001001
NO NO No
PUCCH format 2. TDLBFD-002009
3GPP TS 36.213. TDLBFD-002026
value TDLBFD-001001
NO NO No
PUCCH format 2a. TDLBFD-002009
3GPP TS 36.213. TDLBFD-002026

value TDLBFD-001001
NO NO No
PUCCH format 2b. TDLBFD-002009
3GPP TS 36.213. TDLBFD-002026
Indicates the power

offset (delta value)
LBFD-001001 /
of message 3
TDLBFD-001001
relative to the
LBFD-002009 /
preamble. This NO NO No
TDLBFD-002009
power offset has a
LBFD-002026 /
step size of 2. For
TDLBFD-002026
details, see 3GPP
TS 36.213.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
tracking area
identity of the cell,
which uniquely YES YES No None
identifies an
operator within a
cell.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates the local

LBFD-001001 /
uniquely identifies a YES YES No
TDLBFD-001001
cell within an
eNodeB.

of the uplink time
alignment timer for LBFD-001001 /
UEs in the cell. A TDLBFD-001001
NO NO No
UE is considered LBFD-002009 /
not time-aligned in TDLBFD-002009
the uplink if the
timer expires.
Indicates the local

YES YES No
cell within a BS.
Indicates the timer
value of Timer 300.
For details, see
3GPP TS 36.331.
when the UE sends
RRCConnectionRe
quest.
Before the timer LBFD-001001 /
expires, it is TDLBFD-001001
NO NO No
stopped if the UE LBFD-002009 /
receives TDLBFD-002009
RRCConnectionSet
up or
RRCConnectionRej
ect.
After the timer
expires, the UE
directly enters the
RRC_IDLE state.

of timer 301. For
details, see 3GPP
TS 36.331.
when the UE sends
an RRC Connection
Reestablishment
Request message.
The timer is
stopped if, before it
expires, the UE
receives an RRC
Connection LBFD-001001 /
Reestablishment or TDLBFD-001001
NO NO No
RRC Connection LBFD-002009 /
Reestablishment TDLBFD-002009
Reject message.
The timer is also
stopped if the
selected cell
becomes an
unsuitable cell. For
the definition of a
suitable cell, see
3GPP TS 36.331.
After the timer
expires, the UE
enters the
RRC_IDLE mode.
of timer 310. For
details, see 3GPP
TS 36.331.
when the UE
detects any fault at
the physical layer.
The timer is
stopped if the UE
detects one of the
following before the
timer expires: (1)
The physical-layer
fault is rectified; (2)
LBFD-001001 /
A handover is
TDLBFD-001001
triggered; (3) The NO NO No
LBFD-002009 /
UE initiates an RRC
TDLBFD-002009
connection
reestablishment
procedure.
After the timer
expires, the UE
enters the
RRC_IDLE mode if
the security mode is
not activated. If the
security mode is
activated, the UE
initiates an RRC
connection
reestablishment
procedure.

of timer 311. For
details, see 3GPP
TS 36.331.
when the UE starts
the RRC
connection
reestablishment
LBFD-001001 /
procedure.
TDLBFD-001001
The timer is NO NO No
LBFD-002009 /
stopped if, before
TDLBFD-002009
the timer expires,
the UE selects an
E-UTRAN or inter-
RAT cell to camp
on.
After the timer
expires, the UE
enters the
RRC_IDLE mode.
Indicates the
LBFD-001001 /
maximum number
TDLBFD-001001
of successive "in NO NO No
LBFD-002009 /
sync" indications
TDLBFD-002009
received from L1.
Indicates the
LBFD-001001 /
maximum number
TDLBFD-001001
of successive "out NO NO No
LBFD-002009 /
of sync" indications
TDLBFD-002009
received from L1.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the name

NO YES No None
of the cell.
Indicates the ID of
the sector to which NO YES No None
the cell belongs.
Indicates whether
the cell is a closed
subscriber group
(CSG) cell. A CSG
cell has restrictions
on UE access. It
broadcasts a
specific CSG ID in
the SIB and only
those UEs of the
group can access LBFD-002009 /
NO NO No
the CSG cell. TDLBFD-002009
BOOLEAN_FALSE
indicates that the
cell is not a CSG
cell, and
BOOLEAN_TRUE
indicates that the
cell is a CSG cell.
Currently, Huawei
eNodeBs do not
support CSG cells.
Indicates the UL
cyclic prefix length
of a cell. A cyclic
prefix can be a
common or
extended cyclic
prefix. An extended
cyclic prefix is
generally used in a
complex
LBFD-002009 /
environment with a
TDLBFD-002009
strong multi-path
LBFD-001004 /
effect and long
delay. In a cell, the
LBFD-00100401 /
UL cyclic prefix
TDLBFD-00100401
length can be
LOFD-001031
different from the
DL one. In addition,
the UL or DL cyclic
prefix length of a
cell must be the
same as that of the
cell using the same
LBBP. For details,
see 3GPP TS
36.211.
of the DL cyclic
prefix of a cell. A DL
cyclic prefix can be
a common or
extended cyclic
prefix. An extended
cyclic prefix is
generally used in a
complex
environment with a
LBFD-001004 /
strong multi-path
TDLBFD-001004
effect and long
NO NO No LBFD-00100401 /
delay. In a cell, the
TDLBFD-00100401
UL cyclic prefix
LOFD-001031
length can be
different from the
DL one. In addition,
the UL or DL cyclic
prefix length of a
cell must be the
same as that of the
cell using the same
LBBP. For details,
see 3GPP TS
36.211.
Indicates the
LBFD-002009 /
frequency band in
TDLBFD-002009
which the cell
LBFD-001007 /
operates. For NO YES No
TDLBFD-001008
details about this
LBFD-001008 /
parameter, see
TDLBFD-001009
3GPP TS 36.104.
Indicates whether
to configure the UL
EARFCN of the cell.
For an FDD cell, if
no UL EARFCN is
configured, the UL
LBFD-002009 /
EARFCN equals NO NO No
TDLBFD-002009
the sum of the DL
EARFCN and
18000 by default.
For a TDD cell, the
UL EARFCN equals
the DL EARFCN.
Indicates the UL
EARFCN of the cell.
It is optional,
depending on the
setting of the UL
EARFCN
configuration LBFD-002009 /
indicator TDLBFD-002009
(UlEarfcnCfgInd). If LBFD-001007 /
NO NO No
the value of this TDLBFD-001008
parameter is not LBFD-001008 /
specified, the TDLBFD-001009
default UL EARFCN
is used, which is
calculated based on
the DL EARFCN.
For details, see
3GPP TS 36.104.
LBFD-002009 /
Indicates the DL TDLBFD-002009
EARFCN of the cell. LBFD-001007 /
NO YES No
For details, see the TDLBFD-001008
3GPP TS 36.104. LBFD-001008 /
TDLBFD-001009
Indicates the UL
bandwidth of the
cell, which is based
on the number of
resource blocks
(RBs). The value
CELL_BW_N25
indicates a cell
bandwidth of 25
RBs. The value
LBFD-001003 /
CELL_BW_N50
TDLBFD-001003
indicates a cell NO YES No
LBFD-002009 /
bandwidth of 50
TDLBFD-002009
RBs. The mapping
between the
parameter value
and the actual cell
bandwidth (that is,
the number of RBs)
can be deduced
similarly. For
details, see 3GPP
TS 36.104.
Indicates the DL
bandwidth of the
cell, which is based
on the number of
resource blocks
(RBs). The value
CELL_BW_N25
indicates a cell
bandwidth of 25
RBs. The value
LBFD-001003 /
CELL_BW_N50
TDLBFD-001003
indicates a cell NO YES No
LBFD-002009 /
bandwidth of 50
TDLBFD-002009
RBs. The mapping
between the
parameter value
and the actual cell
bandwidth (that is,
the number of RBs)
can be deduced
similarly. For
details, see 3GPP
TS 36.104.
Indicates the ID of
the E-UTRAN cell.
The combination of
this parameter and
the eNodeB ID
forms the E-UTRAN
cell identity. The LBFD-002009 /
NO YES No
combination of the TDLBFD-002009
E-UTRAN cell
identity and the
PLMN identity
forms the ECGI. For
details, see 3GPP
TS 36.413.
Indicates the
physical cell ID. For LBFD-002009 /
NO YES No
details, see 3GPP TDLBFD-002009
TS 36.331.
Indicates the
additional spectrum
emission, which
restricts the LBFD-002009 /
NO NO No
emission power of TDLBFD-002009
the UEs in the cell.
For details, see the
3GPP TS 36.101.

state of the cell. It
consists of the NO NO No None
activated and
deactivated states.
Indicates the
administrative state,
which can be
Unblock, High
block, Middle block,
or Low block.If the
CellAdminState
parameter is set to
CELL_HIGH_BLOC
K, the cell is
deactivated
immediately. If the
CellAdminState
parameter is set to
CELL_MIDDLE_BL
OCK, the cell is
deactivated when it
has no user to
NO NO No None
serve during the
time period
specified by the
CellMidBlkTimer
parameter, and is
deactivated when
the timer expires
irrespective of
whether it has
users to serve. If
the CellAdminState
parameter is set to
CELL_LOW_BLOC
K, the cell is
deactivated only
when the cell does
not have any users
to serve.

of the timer used to
determine whether
to block a middle-
blocking-priority
cell. If
CellAdminState is
set to
CELL_MIDDLE_BL
NO NO No None
OCK, the cell is
deactivated when
no user accesses
the cell during the
period of time
specified by this
parameter. The cell
is also deactivated
if the timer expires.
Indicates the duplex
mode of the cell.
CELL_FDD
indicates the FDD LBFD-002009 /
NO YES No
mode, and TDLBFD-002009
CELL_TDD
indicates the TDD
mode.
Indicates the ratio
of UL subframes to LBFD-002009 /
DL subframes in a TDLBFD-002009
NO NO No
TDD cell. For TDLBFD-00100701
details, see 3GPP TDLOFD-00102601
TS 36.211.
Indicates the ratio
of special UL LBFD-002009 /
subframes to TDLBFD-002009
special DL NO NO No TDLBFD-00100702
subframes in a TDD TDLOFD-00102602
cell. For details, see TDLOFD-00102603
3GPP TS 36.211.
Indicates the cell
specific offset for
the serving cell. It
affects the
probability of
triggering
handovers from the
serving cell to its NO NO No None
intra-frequency
neighboring cells. A
parameter leads to
a higher probability.
For details, see
3GPP TS 36.331.
Indicates the
specific frequency
offset of the serving
cell. This parameter
is contained in the
intra-frequency
measurement
control information NO NO No None
and is related to the
handover difficulty
between the
serving cell and the
neighboring cell.
For details, see
3GPP TS 36.331.
Indicates the first
logical root
sequence, which is
used to generate
the preamble
sequence. Each
logical root
sequence
LBFD-002010 /
corresponds to a NO YES No
TDLBFD-002010
physical root
sequence. For the
mapping between
logical root
sequences and
physical root
sequences, see
3GPP TS 36.211.
Indicates the speed
flag of the cell. Set
this parameter to
ULTRA_HIGH_SPE
ED if the cell is
used to provide
coverage for an
LOFD-001007 /
ultra-high-speed
TDLOFD-001007
railway. Set this NO NO No
LOFD-001008 /
parameter to
TDLOFD-001008
HIGH_SPEED if the
cell is used to
provide coverage
for a high way. Set
this parameter to
LOW_SPEED in
other scenarios.
Indicates the
preamble format
used in the cell.
Cells set up on one
LBFD-002010 /
LBBP must use the NO NO No
TDLBFD-002010
same preamble
format. For details,
see 3GPP TS
36.211.
Indicates the radius LBFD-002010 /
NO NO No
of the cell. TDLBFD-002010
Indicates whether
to configure
bandwidth
customization for
LOFD-001051
the cell. Bandwidth
customization is
TDLBFD-001003
available only when
the bandwidth is 5
MHz, 10 MHz, 15
MHz, or 20 MHz.
Indicates the
customized UL cell
bandwidth.
Bandwidth LOFD-001051
customization is NO NO No LBFD-001003 /
available only when TDLBFD-001003
the bandwidth is 5
MHz, 10 MHz, 15
MHz, or 20 MHz.
Indicates the
customized DL cell
bandwidth.
Bandwidth LOFD-001051
customization is NO NO No LBFD-001003 /
available only when TDLBFD-001003
the bandwidth is 5
MHz, 10 MHz, 15
MHz, or 20 MHz.
Indicates whether
LBFD-002009 /
to set an NO NO No
TDLBFD-002009
emergency area ID.
Indicates the
emergency area ID. LBFD-002009 /
NO NO No
3GPP TS 36.413.
Indicates whether
to set the maximum
LBFD-001001
transmit power that
a UE can apply to
LBFD-002026
uplink transmission
in the cell.
Indicates the
maximum transmit
power that a UE
can apply to uplink
transmission in the
cell. It is contained
in system
information block
LBFD-001001
type 1 (SIB1). If this
parameter is not
LBFD-002026
specified in SIB1,
the maximum
transmit power that
the UE can
physically achieve
is used as this
maximum transmit
power.
Indicates whether
the multi-RRU cell
feature.
Indicates the type
of the multi-RRU
cell.The value
TWO_RRU_COMBI
NATION(TWO RRU NO NO No TDLOFD-001075
Combination)
applies to ultra-
high-speed railway
scenarios.
Indicates the CPRI
compression type
of the cell. CPRI
compression is
used in RRU
cascading
scenarios to
improve the
cascading
specifications
without changing
the CPRI data rate.
This parameter can
be set to
NO NO No None
NO_COMPRESSIO
N or
NORMAL_COMPR
ESSION. The value
NO_COMPRESSIO
N indicates that
CPRI compression
is not used, and the
value
NORMAL_COMPR
ESSION indicates
that CPRI
compression is
used.
Indicates the state
NO NO Yes None
of the cell instance.
Indicates the
reason that causes
the latest state
change of the cell,
NO NO Yes None
which can be a cell
activation success
or a cell setup
failure.
Indicates the latest

setup time of the NO NO Yes None
cell.
setup type of the NO NO Yes None
cell.

remove time of the NO NO Yes None
cell.
remove type of the NO NO Yes None
cell.
Indicates the
energy saving
status of the cell.
There are five
states: RF
intelligent
shutdown, cell
intelligent NO NO Yes None
shutdown, low
power consumption
mode, automatic
power-off at a
specified time, and
inter-rat cell
shutdown mode.
Indicates the slot

number of the
baseband
NO NO Yes None
processing board
where the cell is
configured.
Indicates the
NO NO Yes None
topology of the cell.
Indicates the
cabinet number of
NO NO Yes None
the RRU or RFU
that serves the cell.
Indicates the
subrack number of
NO NO Yes None
the RRU or RFU
that serves the cell.
Indicates the slot
number of the RRU
NO NO Yes None
or RFU that serves
the cell.
Indicates whether
the cell is in the
NO NO Yes None
symbol power
saving state.
Indicates the
maximum transmit
power of the cell in
theory. The value
65535 indicates
that this parameter
is invalid, which can
be changed by NO NO Yes None
modifying the
PDSCH
configuration or the
PA parameters
related to power
control for the
PDSCH.
Indicates the cell ID
of the local cell. It
cell within an
eNodeB.
Indicates the
maximum number
of beamforming
layers, that is, the
rank of
beamforming. The
value
SINGLE_LAYER_B
F indicates single-
stream TDLOFD-001049
NO NO No
beamforming (that TDLOFD-009003
is, beamforming
with the rank of 1),
and the value
DUAL_LAYER_BF
indicates dual-
stream
beamforming (that
is, beamforming
with the rank of 2).
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
interval between
periodic
reports that are TDLBFD-00202201
NO NO No
sent after a DL ICIC LOFD-00101401 /
measurement event TDLOFD-00101401
is triggered. For
details, see 3GPP
TS 36.331.
Indicates the
maximum number
of cells to be
included in each LBFD-00202201 /
measurement TDLBFD-00202201
NO NO No
report after a DL LOFD-00101401 /
ICIC measurement TDLOFD-00101401
event is triggered.
For details, see
3GPP TS 36.331.
Indicates the
number of periodic
reports after a DL TDLBFD-00202201
NO NO No
ICIC measurement LOFD-00101401 /
event is triggered. TDLOFD-00101401
For details, see
3GPP TS 36.331.
Indicates the
quantity to be
included in the
measurement
report after a DL
ICIC measurement
event is triggered.
The quantity can be
RSRP or RSRQ.
The measured
RSRP values are
with the load, and
therefore there is
LBFD-00202201 /
little signal
TDLBFD-00202201
fluctuation. The NO NO No
LOFD-00101401 /
measured RSRQ
TDLOFD-00101401
load and are likely
real time. If this
parameter is set to
BOTH, the actual
quantity to be used
is the same as the
DL ICIC
measurement
trigger quantity. For
details, see 3GPP
TS 36.331.
Indicates the
evaluation of a DL
ICIC measurement
event. The quantity
can be RSRP or
RSRQ. The
measured RSRP
values are stable, LBFD-00202201 /
varying little with TDLBFD-00202201
NO NO No
the load, and LOFD-00101401 /
therefore there is TDLOFD-00101401
little signal
fluctuation. The
measured RSRQ
load but are likely to
reflect the signal
real time.
Indicates the
hysteresis for the
DL ICIC
measurement
event. This
parameter is used
to decrease
frequent triggering LBFD-00202201 /
of event evaluations TDLBFD-00202201
NO NO No
due to radio signal LOFD-00101401 /
fluctuations. In this TDLOFD-00101401
way, the probability
of ping-pong
handovers or
handover decision
errors is reduced.
For details, see
3GPP TS 36.331.
Indicates the time-

to-trigger for the DL
ICIC measurement
event. When
detecting that the
in at least one
neighboring cell
meet the entering
LBFD-00202201 /
condition, the UE
TDLBFD-00202201
does not send a NO NO No
LOFD-00101401 /
measurement
TDLOFD-00101401
report to the
eNodeB
immediately.
Instead, the UE
sends a report only
when the signal
meets the entering
time-to-trigger.
for the DL ICIC
measurement
event. This offset
specifies the
difference between
a neighboring cell
and that of the
serving cell before
a DL ICIC
measurement event LBFD-00202201 /
can be triggered. If TDLBFD-00202201
NO NO No
set to a large value, TDLOFD-00101401
the neighboring cell
must be
than that of the
serving cell before
a DL ICIC
measurement event
can be triggered.
For details, see
3GPP TS 36.331.
Indicates the local

ID of the cell. It LOFD-001040 /
YES YES No
uniquely identifies a TDLOFD-001040
cell within a BS.

for the functionality
of the low power
consumption mode.
The cell can enter
LOFD-001040 /
the low power NO NO No
TDLOFD-001040
consumption mode
only when this
parameter is set to
ON and specific
conditions are met.
for forcibly entering
the low power
consumption mode.
When both this
switch and the
functionality switch
are set to ON, the
cell enters the low
power consumption
mode as soon as
the wait time for
entering the mode
elapses, regardless
of whether it is
within the low
power consumption
period. When the LOFD-001040 /
NO NO No
functionality switch TDLOFD-001040
is set to ON but this
switch is set to OFF,
the cell enters the
low power
consumption mode
as soon as the wait
time for entering the
mode elapses, if a
Mains Input
Abnormal alarm
indicating an
absence of AC
power supplies is
reported within the
low power
consumption
period.
Indicates the start
time of the low LOFD-001040 /
NO NO No
power consumption TDLOFD-001040
mode.
Indicates the stop

time of the low
power consumption
mode. If the stop
time is earlier than LOFD-001040 /
NO NO No
or the same as the TDLOFD-001040
start time, the stop
time is assumed to
be a time of the
next day.
Indicates the
duration in which
the transmit power
LOFD-001040 /
for services is NO NO No
TDLOFD-001040
reduced in the cell
in low power
consumption mode.
Indicates the
duration in which
the reference signal
LOFD-001040 /
transmit power is NO NO No
TDLOFD-001040
reduced in the cell
in low power
consumption mode.
Indicates the
duration in which
RF channels are LOFD-001040 /
NO NO No
shut down in the TDLOFD-001040
cell in low power
consumption mode.
Indicates the
percentage of the
transmit power for
services to the total
transmit power for
services when the LOFD-001040 /
NO NO No
low power TDLOFD-001040
consumption mode
is implemented by
means of reducing
the transmit power
for services.
Indicates the
amount by which
LOFD-001040 /
transmit power is NO NO No
TDLOFD-001040
reduced in the cell
in low power
consumption mode.
entering the low
power consumption
mode. In low power
consumption mode,
a cell automatically
takes the following
actions in
sequence: (1)
reduces the
transmit power for
services; (2)
reduces the
transmit power for
reference signals;
(3) shuts down
power amplifiers
(PAs) for half of the
TX channels in the
LOFD-001040 /
cell; (4) shuts down NO NO No
TDLOFD-001040
the cell. This
duration smoothes
the transition from
the normal mode to
the low power
consumption mode
for the cell. If the
conditions for the
cell to enter the low
power consumption
mode are no longer
met during this
period of time, the
cell will not enter
the low power
consumption mode;
otherwise, it enters
the low power
Indicates the local
ID of the cell. It
cell within an
eNodeB.
upper and lower
limits of the CIO
adjustment range
for the cell in intra-
frequency MRO are
calculated by using
the following
formulas: Lower
limit = Off + ofs +
ocs - ofn + Hys - 5,
Upper limit = Off +
ofs + ocs - ofn +
Hys - 2, where Off
is the offset for
intra-frequency
handover, ofs and
ofn are the
frequency-specific
LOFD-002005 /
offsets for the NO NO No
TDLOFD-002005
serving frequency
and neighboring
frequency
respectively, ocs is
the cell-specific
offset for the
serving cell, and
Hys is the
hysteresis for intra-
frequency
handover. If this
parameter is set to
NOT_CFG, the
upper and lower
limits of the CIO
adjustment range
for the cell in inter-
frequency MRO are
Indicates the upper
limit of the CIO LOFD-002005 /
NO NO No
adjustment range TDLOFD-002005
for the cell.
Indicates the lower

limit of the CIO LOFD-002005 /
NO NO No
adjustment range TDLOFD-002005
for the cell.
Indicates the local

cell ID. It uniquely LBFD-001001 /
YES YES No
identifies a cell TDLBFD-001001
within a BS.
Indicates the
Allocation and
Retention Priority
(ARP) threshold for
the Golden-level
services. A service LBFD-002023 /
is defined as a TDLBFD-002023
Golden-level LBFD-002024 /
NO NO No
service if its ARP TDLBFD-002024
value is smaller LBFD-003002 /
than or equal to this TDLBFD-003002
threshold. The
service priority has
a negative
correlation with the
ARP value.
Indicates the
Allocation and
Retention Priority
(ARP) threshold for
the Silver-level
services. A service
is defined as a
Silver-level service
if its ARP value is
smaller than or
equal to the value LBFD-002023 /
of this parameter TDLBFD-002023
and is larger than LBFD-002024 /
NO NO No
the value of TDLBFD-002024
GoldServiceArpThd LBFD-003002 /
. A service is TDLBFD-003002
defined as a
Bronze-level
service if its ARP
value is larger than
the value of this
parameter. The
service priority has
a negative
ARP value.
Indicates the
admission threshold
for the handed-over
service with QCI of
1. This threshold
applies to both UL
and DL.
If the satisfaction
rate of services with
QCI of 1 is above or
LBFD-001001 /
equal to this
TDLBFD-001001
threshold, the NO NO No
LBFD-002023 /
handed-over
TDLBFD-002023
service with QCI of
1 can be admitted.
If the satisfaction
QCI of 1 is below
this threshold, the
handed-over
service with QCI of
1 cannot be
admitted.
Indicates the
admission threshold
for the handed-over
service with QCI of
2. This threshold
applies to both UL
and DL.
If the satisfaction
LBFD-001001 /
equal to this
TDLBFD-001001
LBFD-002023 /
handed-over
TDLBFD-002023
service with QCI of
2 can be admitted.
If the satisfaction
QCI of 2 is below
this threshold, the
handed-over
service with QCI of
2 cannot be
admitted.
Indicates the
admission threshold
for the handed-over
service with QCI of
3. This threshold
applies to both UL
and DL.
If the satisfaction
LBFD-001001 /
equal to this
TDLBFD-001001
LBFD-002023 /
handed-over
TDLBFD-002023
service with QCI of
3 can be admitted.
If the satisfaction
QCI of 3 is below
this threshold, the
handed-over
service with QCI of
3 cannot be
admitted.
Indicates the
admission threshold
for the handed-over
service with QCI of
4. This threshold
applies to both UL
and DL.
If the satisfaction
LBFD-001001 /
equal to this
TDLBFD-001001
LBFD-002023 /
handed-over
TDLBFD-002023
service with QCI of
4 can be admitted.
If the satisfaction
QCI of 4 is below
this threshold, the
handed-over
service with QCI of
4 cannot be
admitted.
for admission of
new Gold-level
services. The value
of this parameter
applies in both UL
and DL. New Gold-
level services with
QCI N can be
admitted if both the
are met: (1) The
satisfaction rate of
services with QCI N LBFD-001001 /
is higher than or TDLBFD-001001
NO NO No
equal to the sum of LBFD-002023 /
this offset and the TDLBFD-002023
admission threshold
for the handed-over
services with QCI
N; (2) The
services with any
other QCI is higher
corresponding
admission threshold
for the handed-over
services with that
QCI.
for admission of
new Silver-level
services. The value
of this parameter
applies in both UL
and DL. New Silver-
level services with
QCI N can be
admitted if both the
are met: (1) The
services with QCI N LBFD-001001 /
is higher than or TDLBFD-001001
NO NO No
equal to the sum of LBFD-002023 /
this offset and the TDLBFD-002023
admission threshold
for the handed-over
services with QCI
N; (2) The
services with any
other QCI is higher
corresponding
admission threshold
for the handed-over
services with that
QCI.
for admission of
new Bronze-level
services. The value
of this parameter
applies in both UL
and DL. New
Bronze-level
services with QCI N
can be admitted if
both the following
conditions are met:
(1) The satisfaction
LBFD-001001 /
QCI N is higher
TDLBFD-001001
than or equal to the NO NO No
LBFD-002023 /
sum of this offset
TDLBFD-002023
and the admission
threshold for the
handed-over
services with QCI
N; (2) The
services with any
other QCI is higher
corresponding
admission threshold
for the handed-over
services with that
QCI.
Indicates the
congestion
threshold for
services with QCI of
1. This threshold
applies to both UL
and DL.
If the satisfaction
QCI of 1 in the cell
becomes lower
than this threshold, LBFD-001001 /
the services with TDLBFD-001001
NO NO No
QCI of 1 enter the LBFD-002024 /
congested state. TDLBFD-002024
If the satisfaction
becomes higher
than the sum of this
threshold and the
congestion relief
offset, the services
with QCI of 1 leave
the congested
state.
Indicates the
congestion
threshold for
2. This threshold
applies to both UL
and DL.
If the satisfaction
becomes lower
NO NO No
If the satisfaction
becomes higher
threshold and the
congestion relief
with QCI of 2 leave
the congested
state.
Indicates the
congestion
threshold for
3. This threshold
applies to both UL
and DL.
If the satisfaction
rate of the services
with QCI of 3 in the
cell becomes lower
NO NO No
If the satisfaction
becomes higher
threshold and the
congestion relief
with QCI of 3 leave
the congested
state.
Indicates the
congestion
threshold for
4. This threshold
applies to both UL
and DL.
If the satisfaction
becomes lower
NO NO No
If the satisfaction
becomes higher
threshold and the
congestion relief
with QCI of 4 leave
the congested
state.
Indicates the rate
reduction proportion
for Gold-level GBR
services. When
congestion occurs,
the rate that the
scheduling
algorithm provides
for Gold-level GBR
services (except
VoIP services) is
the product of GBR
LBFD-001001 /
and this
TDLBFD-001001
proportion.This NO NO No
LBFD-002024 /
parameter will be
TDLBFD-002024
versions. In this
still synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
Indicates the rate

for Silver-level GBR
services. When
congestion occurs,
the rate that the
scheduling
algorithm provides
for Silver-level GBR
services (except
VoIP services) is
the product of the
LBFD-001001 /
GBR and this
TDLBFD-001001
proportion.This NO NO No
LBFD-002024 /
parameter will be
TDLBFD-002024
versions. In this
still synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
Indicates the rate
for Bronze-level
GBR services.
When congestion
occurs, the rate that
the scheduling
algorithm provides
for Bronze-level
GBR services
(except VoIP
services) is the
LBFD-001001 /
product of GBR and
TDLBFD-001001
this proportion.This NO NO No
LBFD-002024 /
parameter will be
TDLBFD-002024
versions. In this
still synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
Indicates the
threshold for high
PRB usage by GBR
services. The value
expressed in
percentage and
applies to both UL
and DL. If the MAC
layer detects that
LBFD-001001 /
the PRB usage by
TDLBFD-001001
GBR services NO NO No
LBFD-002023 /
exceeds the
TDLBFD-002023
threshold, the
usage is high. In
this situation, new
GBR services are
not admitted if
GbrUsageSwitch
under the
RacAlgoSwitch
parameter is turned
on.
Indicates the
threshold for low
PRB usage by GBR
services. The value
expressed in
percentage and LBFD-001001 /
applies to both UL TDLBFD-001001
NO NO No
and DL. If the MAC LBFD-002023 /
layer detects that TDLBFD-002023
the PRB usage by
GBR services falls
below the
threshold, the
usage is considered
to be low.
Indicates the
Allocation and
Retention Priority
(ARP) threshold for
low Energy
Efficiency Ratio
(EER) services. If
the ARP value of a
service is less than
the value of this
parameter, the
service will not be
released for LBFD-001001 /
congestion TDLBFD-001001
NO NO No
control.This LBFD-002024 /
parameter will be TDLBFD-002024
versions. In this
still synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
Indicates the
congestion release
offset. The service
of a specific QCI
exits the congestion
state if the
the service exceeds
the sum of this
congestion release
LBFD-001001 /
offset and the
TDLBFD-001001
congestion NO NO No
LBFD-002024 /
threshold for the
TDLBFD-002024
QCI. The service
retains the
congestion state if
the satisfaction rate
is below the sum of
this congestion
release offset and
the congestion
threshold for the
QCI.
Indicates the
Allocation and
Retention Priority
(ARP) threshold for
preemption. The
services that have
ARP values larger
value of this
parameter are
preemptible.This LBFD-001001 /
parameter will be TDLBFD-001001
NO NO No
removed in the later LOFD-00102901 /
versions. In this TDLOFD-00102901
still synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
Indicates the
threshold for
deciding on
whether the UL RB
usage is high. This
LBFD-001001 /
threshold applies to
TDLBFD-001001
UL admission
LBFD-002023 /
decision. If the UL NO NO No
TDLBFD-002023
RB usage reported
LBFD-002024 /
by the MAC layer is
TDLBFD-002024
above this
threshold, the UL
RB usage is
assumed to be
high.
Indicates the
threshold for
deciding on
whether the DL
resource block (RB)
usage is high. This LBFD-001001 /
threshold applies to TDLBFD-001001
DL admission LBFD-002023 /
NO NO No
decision. If the TDLBFD-002023
usage of the DL RB LBFD-002024 /
reported by the TDLBFD-002024
MAC layer is above
this threshold, the
DL RB usage is
assumed to be
high.
Indicates the
threshold for
deciding on
whether the UL RB
LBFD-001001 /
usage is low. It
TDLBFD-001001
applies to UL
LBFD-002023 /
admission decision. NO NO No
TDLBFD-002023
If the UL RB usage
LBFD-002024 /
reported by the
TDLBFD-002024
MAC layer is below
this threshold, the
UL RB usage is
assumed to be low.
Indicates the
threshold for
deciding on
whether the DL
resource block (RB)
usage is low. This LBFD-001001 /
threshold applies to TDLBFD-001001
DL admission LBFD-002023 /
NO NO No
decision. If the TDLBFD-002023
usage of the DL RB LBFD-002024 /
reported by the TDLBFD-002024
MAC layer is below
this threshold, the
usage of the DL RB
is assumed to be
low.
Indicates the
maximum number
of non-GBR
services (excluding
IP Multimedia LBFD-001001 /
Subsystem [IMS] TDLBFD-001001
NO NO No
services) that can LBFD-002023 /
be provided by a TDLBFD-002023
cell. The value of
this parameter is
applied to both UL
and DL.
Indicates the local

YES YES No
cell within a BS.
Indicates whether
RF channel
for the cell. RF
channel intelligent LOFD-001039 /
NO NO No
shutdown can be TDLOFD-001039
performed in the
cell only when this
parameter is set to
ON and certain
conditions are met.
Indicates the start

time of the cell RF
intelligent
shutdown.
Indicates the stop
time of RF channel
for the cell. If the
stop time is earlier LOFD-001039 /
NO NO No
than or the same as TDLOFD-001039
the start time, the
stop time is
assumed to be a
time of the next day.
Indicates the value

by which the
reference signal
power is increased
during the RF
channel intelligent
shutdown period.
The reference
signal power LOFD-001039 /
NO NO No
increases by the TDLOFD-001039
value specified by
this parameter to
ensure coverage of
the cell. If this
parameter is set to
a value greater than
3, the value 3
applies in effect.
Indicates the local

cell within an
eNodeB.

for the remote
interference
cancellation
algorithm. If this
the eNodeB
performs remote
interference
detection and
NO NO No None
records in call
history record
(CHR) logs if any
interference is
detected. If this
switch is turned off,
the eNodeB does
not perform remote
interference
detection.
Indicates the
number of empty
symbols in an
uplink pilot timeslot
(UpPTS). If this
parameter is set to
a non-zero value N,
then no data is
transmitted within
the N symbols
starting from the
NO NO No None
first symbol in the
UpPTS. Note that,
for any given
special subframe
configuration, the
value of this
parameter cannot
be greater than the
total number of
symbols contained
in the UpPTS.
Indicates whether
to empty the last
NO NO No None
symbol in each
uplink subframe.
Indicates the local
YES YES No
cell within a BS.
Indicates whether
cell intelligent
shutdown. Cell
can be performed
only when this
parameter is set to
ON and specific LOFD-001042 /
NO NO No
conditions are met. TDLOFD-001042
For cell intelligent
shutdown, each
basic cell must
have its cell
enabled and the UL
or DL PRB usage
threshold set to 0.
Indicates the start
time of cell
intelligent
shutdown. If the
NO NO No
the start time, the
stop time is
assumed to be a
Indicates the stop
time of cell
intelligent
shutdown. If the
NO NO No
the start time, the
stop time is
assumed to be a
time of thefor
threshold next
cellday.
intelligent
shutdown. For cell
intelligent
shutdown, each
basic cell must
have its cell
enabled and the UL
or DL PRB usage
threshold set to 0.
The local cell enters
cell intelligent
shutdown mode if
its UL and DL loads
are lower than the
UL and DL PRB
usage thresholds,
respectively, and LOFD-001042 /
NO NO No
the total load of the TDLOFD-001042
local and basic cells
is lower than the
sum of the UL PRB
usage threshold
and offset as well
as the sum of the
DL PRB usage
threshold and
offset. The local cell
exits cell intelligent
shutdown mode if
the load of any
basic cell is higher
sum of the UL PRB
usage threshold
and offset, or the
sum of the DL PRB
for cell intelligent
shutdown. For cell
intelligent
shutdown, each
basic cell must
have its cell
enabled and the UL
or DL PRB usage
threshold set to 0.
cell intelligent
shutdown mode if
its UL and DL loads
are lower than the
UL and DL PRB
usage thresholds,
respectively, and
LOFD-001042 /
the total load of the NO NO No
TDLOFD-001042
is lower than the
sum of the UL PRB
usage threshold
and offset as well
as the sum of the
DL PRB usage
threshold and
shutdown mode if
the load of any
sum of the UL PRB
usage threshold
and offset, or the
sum of the DL PRB
threshold for cell
intelligent
shutdown. For cell
intelligent
shutdown, each
basic cell must
have its cell
enabled and the UL
or DL PRB usage
threshold set to 0.
cell intelligent
shutdown mode if
its UL and DL loads
are lower than the
UL and DL PRB
usage thresholds,
respectively, and LOFD-001042 /
NO NO No
the total load of the TDLOFD-001042
is lower than the
sum of the UL PRB
usage threshold
and offset as well
as the sum of the
DL PRB usage
threshold and
shutdown mode if
the load of any
sum of the UL PRB
usage threshold
and offset, or the
sum of the DL PRB
shutdown. For cell
intelligent
shutdown, each
basic cell must
have its cell
enabled and the UL
or DL PRB usage
threshold set to 0.
cell intelligent
shutdown mode if
its UL and DL loads
are lower than the
UL and DL PRB
usage thresholds,
respectively, and
LOFD-001042 /
the total load of the NO NO No
TDLOFD-001042
is lower than the
sum of the UL PRB
usage threshold
and offset as well
as the sum of the
DL PRB usage
threshold and
shutdown mode if
the load of any
sum of the UL PRB
usage threshold
and offset, or the
sum of the DL PRB
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
interval between
periodic
measurement
reports that are
sent after a UL ICIC
measurement event
is triggered. For
details, see 3GPP
TS 36.331. LBFD-00202202 /
In this version, this TDLBFD-00202202
NO NO No
parameter still LOFD-00101402 /
supports setting TDLOFD-00101402
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.
Indicates the
maximum number
of cells to be
included in each
measurement
report after a UL
ICIC measurement
event is triggered.
For details, see
3GPP TS 36.331. LBFD-00202202 /
In this version, this TDLBFD-00202202
NO NO No
parameter still LOFD-00101402 /
supports setting TDLOFD-00101402
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.
Indicates the
number of periodic
measurement
reports after a UL
ICIC measurement
event is triggered.
For details, see
3GPP TS 36.331.
In this version, this LBFD-00202202 /
parameter still TDLBFD-00202202
NO NO No
supports setting LOFD-00101402 /
synchronization TDLOFD-00101402
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.
measurement
report for a UL ICIC
measurement
event. The quantity
can be RSRP or
RSRQ. The
measured RSRP
values are stable,
varying little with
the load, and
therefore there is
little signal
fluctuation. The
measured RSRQ
load and are likely
quality of the cell in LBFD-00202202 /
real time. If this TDLBFD-00202202
NO NO No
BOTH, the actual TDLOFD-00101402
quantity to be used
is the same as the
triggering quantity
for the UL ICIC
measurement
event. For details,
see 3GPP TS
36.331.
In this version, this
parameter still
supports setting
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
Indicates the
evaluation of a UL
ICIC measurement
event. The quantity
can be RSRP or
RSRQ. The
measured RSRP
values are stable,
varying little with
the load, and
therefore there is
little signal
fluctuation. The
measured RSRQ LBFD-00202202 /
values vary with the TDLBFD-00202202
NO NO No
load and are likely LOFD-00101402 /
to reflect the signal TDLOFD-00101402
real time.
parameter still
supports setting
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.
Indicates the
hysteresis for the
UL ICIC
measurement
event. This
parameter is used
to decrease
frequent triggering
of event evaluations
due to radio signal
fluctuations. For
LBFD-00202202 /
details, see 3GPP
TDLBFD-00202202
TS 36.331. NO NO No
LOFD-00101402 /
TDLOFD-00101402
parameter still
supports setting
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.
Indicates the time-
to-trigger for the UL
ICIC measurement
event. When
detecting that the
in at least one
neighboring cell
meet the entering
condition, the UE
does not send a
measurement
report to the
eNodeB
immediately.
LBFD-00202202 /
Instead, the UE
TDLBFD-00202202
sends a report only NO NO No
LOFD-00101402 /
when the signal
TDLOFD-00101402
meets the entering
time-to-trigger.
parameter still
supports setting
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.
for the UL ICIC
measurement
event. If this
parameter is set to
a large value, the
LBFD-00202202 /
neighboring cell
TDLBFD-00202202
must be NO NO No
LOFD-00101402 /
TDLOFD-00101402
than that of the
serving cell before
a UL ICIC
measurement event
is triggered. For
details, see 3GPP
TS 36.331.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
proportional fair
(PF), round Robin
(RR), and
enhanced
proportional fair
(EPF). The MAX C/I
policy schedules
UEs in descending
order of average
signal to
interference plus
noise ratio (SINR).
The PF policy
schedules UEs in
ascending order of
ratio of the data
rate to the SINR.
The RR policy LBFD-002025 /
schedules each UE TDLBFD-002025
NO NO No
in sequence, and LOFD-001015 /
therefore each UE TDLOFD-001015
has an equal
opportunity to be
scheduled. The
EPF policy
schedules UEs in
ascending order of
priority. In EPF, the
priority of an UE is
calculated based on
the following
factors: the data
rate, average SINR,
QoS-satisfying data
rate for each
service, and service
differentiation
requirements of the
that is used to
control whether to
enable or disable
UL adaptive HARQ.
to
ADAPTIVE_HARQ_
SW_OFF, UL data
is retransmitted by
non-adaptive
synchronous
HARQ. If this switch
is set to
ADAPTIVE_HARQ_
SW_ON, UL data is
retransmitted by
adaptive LBFD-002006 /
NO NO No
synchronous TDLBFD-002006
HARQ. If this switch
is set to
ADAPTIVE_HARQ_
SW_SEMION,
adaptive HARQ is
triggered when a
UL grant is
delivered to an
HARQ process that
is previously
suspended due to
reasons such as
resource collision,
activation of a
measurement gap,
and PDCCH
congestion.

IBLER of the SINR
adjustment
algorithm. A greater
parameter value LBFD-001006 /
NO NO No
indicates a greater TDLBFD-001006
SINR adjustment
value, and thus a
higher-level MCS is
used.
Indicates the ratio

of the maximum
bandwidth
resources that the
LOFD-00101502 /
uplink scheduler NO NO No
TDLOFD-00101502
can allocate to
preallocation users
to the total system
bandwidth.
Indicates the
minimum interval
between two pre-
allocations. That is,
the actual interval
LOFD-00101502 /
between two pre- NO NO No
TDLOFD-00101502
allocations of one
UE must be longer
value of this
parameter.
Indicates the data

amount pre- LOFD-00101502 /
NO NO No
allocated to each TDLOFD-00101502
user.
Indicates whether
frequency hopping
(FH) is enabled or
disabled and which
FH type is used.
Hopping_OFF:
indicates that FH is
disabled.
Hopping_Type1:
indicates that
adaptive FH is
enabled and FH
type 1 is used. In
this scenario, UEs
in the cell can
determine whether
to use FH based on LBFD-002025 /
the actual situation. TDLBFD-002025
NO NO No
Hopping_Type2: LOFD-001015 /
indicates that TDLOFD-001015
adaptive FH is
enabled and FH
type 2 is used. In
this scenario, UEs
in the cell can
determine whether
to use FH based on
the actual situation.
Hopping_Type2_R
ANDOM: indicates
that random FH is
enabled and FH
type 2 is used. In
this scenario, all
UEs in the cell use
FH.
Indicates the
percentage of free
shared RBs on the
PUSCH in
scheduling based
on free users and
subscribers. The
other RBs on the
PUSCH are
allocated to
subscribers. When
sufficient capacity is
LOFD-00101502 /
available, the
TDLOFD-00101502
percentage of RBs
LBFD-002023 /
occupied by free NO NO No
TDLBFD-002023
users and that
LBFD-002024 /
occupied by
TDLBFD-002024
subscribers will
reach the preset
values. Changes in
this parameter
affect the
percentage of RBs
for free users and
that for subscribers.
The value of this
parameter cannot
be changed when
the cell is active.
Indicates the data

length that the UL
scheduler assigns
to UEs that have
sent scheduling
LOFD-00101502 /
requests. Within the NO NO No
TDLOFD-00101502
data length, the
UEs reports their
buffer status and
transmit certain
data.
Indicates the
threshold for the
number of
consecutive zero-
payload packets
received by the
eNodeB. After
receiving
consecutive zero- LOFD-00101502 /
NO NO No
payload packets of TDLOFD-00101502
a number that is
equal to the value
of this parameter,
the eNodeB
performs implicit
release of semi-
persistent
resources.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates the local

uniquely identifies a YES YES No LOFD-001074
cell within an
eNodeB.

used to enable or
disable inter-RAT
cell shutdown. If
this switch is turned
on, regardless of
the inter-RAT cell
load, UEs in a
lightly loaded E-
UTRAN cell are
handed over or
redirected to
neighboring
GERAN or UTRAN NO NO No LOFD-001074
cells. Then, the E-
UTRAN cell does
not serve any UEs.
In this situation, the
carrier of this cell
can be shut down
to save energy.
Currently, inter-RAT
cell shutdown
applies only to
overlapping areas
of the E-UTRAN
and the UTRAN.
Indicates the start
time of inter-RAT
cell shutdown. If the
stop time is earlier
than or the same as
the start time, the
stop time is
assumed to be the
If the switch for
inter-RAT cell
shutdown is turned
on, inter-RAT cell
shutdown can be
performed during
the period specified
by the start time
and stop time of
inter-RAT cell
shutdown.
Indicates the stop

time of inter-RAT
cell shutdown. If the
stop time is earlier
than or the same as
the start time, the
stop time is
assumed to be the
If the switch for
inter-RAT cell
shutdown is turned
on, inter-RAT cell
shutdown can be
performed during
the period specified
by the start time
and stop time of
inter-RAT cell
shutdown.
Indicates the
threshold number of
UEs served by the
cell. Inter-RAT cell
shutdown is
performed if
shutdown
conditions are met
and the number of
UEs served by the
cell is less than or
equal to this
threshold. The
shutdown
conditions include
the inter-RAT cell
shutdown switch,
specified duration,
and UL/DL physical
resource block
(PRB) thresholds.
eNodeB
automatically hands
over or redirects the
UEs in the E-
UTRAN cell to
GERAN or UTRAN
cells, and then
shuts down the
carrier of the E-
UTRAN cell.
Indicates the
threshold of DL RB
usage in the cell.
Inter-RAT cell
shutdown is
performed if
shutdown
conditions are met
and the real-time
UL RB usage and
DL RB usage in the
cell are less than or
equal to the
thresholds specified
by UlPrbThd and
DlPrbThd,
respectively. The
shutdown
conditions include NO NO No LOFD-001074
the setting of the
inter-RAT cell
shutdown switch,
specified duration,
and threshold of the
number of UEs
served by the cell.
eNodeB
automatically hands
UEs in the E-
UTRAN cell to
GERAN or UTRAN
cells, and then
shuts down the
carrier of the E-
UTRAN cell.
Indicates the
threshold of UL RB
usage in the cell.
Inter-RAT cell
shutdown is
performed if
shutdown
conditions are met
and the real-time
UL RB usage and
DL RB usage in the
cell are less than or
equal to the
thresholds specified
by UlPrbThd and
DlPrbThd,
respectively. The
shutdown
conditions include NO NO No LOFD-001074
the setting of the
inter-RAT cell
shutdown switch,
specified duration,
and threshold of the
number of UEs
served by the cell.
eNodeB
automatically hands
UEs in the E-
UTRAN cell to
GERAN or UTRAN
cells, and then
shuts down the
carrier of the E-
UTRAN cell.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
mode during
handovers.
If the switch is
turned off, the
eNodeB instructs
UEs to use the
contention-based
random access
mode during
handovers.
UnsyncRaSwitch:
used to control the
random access
mode applied when
UEs are out of
LBFD-001001 /
synchronization in
TDLBFD-001001
the uplink.
LBFD-002010 /
If the switch is NO NO No
TDLBFD-002010
turned on, the
LOFD-002015 /
eNodeB instructs
TDLOFD-002015
UEs to use the non-
contention-based
random access
mode upon DL data
arrivals in the case
of out-of-
synchronization.
If the switch is
turned off, the
eNodeB instructs
UEs to use the
contention-based
random access
mode upon DL data
arrivals in the case
of out-of-
used to enable or
disable change in
the cell-specific
SRS subframe
configuration (that
is, the adjustment
on the setting of the
SrsSubframeCfg
parameter).
If the switch is
LBFD-001001 /
turned on, the
TDLBFD-001001
algorithm NO NO No
LBFD-002003 /
dynamically adjusts
TDLBFD-002003
the SRS subframe
configuration based
on the usage of cell
resources.
If the switch is
turned off, the
algorithm uses the
initial configuration
and does not
perform dynamic
switching.

used to enable or
disable the PUCCH
resource
adjustment
algorithm.
If the switch is
turned on, PUCCH
LBFD-001001 /
resource
TDLBFD-001001
adjustment is NO NO No
LBFD-002003 /
initiated when the
TDLBFD-002003
PUCCH resources
are insufficient or
excessive.
If the switch is
turned off, PUCCH
resource
adjustment is
disabled.
that is used to
enable and disable
the Active Queue
Management
(AQM) algorithm.
to ON, the AQM
function is enabled
to prevent or control
congestion. The
length of the PDCP LOFD-001027 /
NO NO No
packet queue is TDLOFD-001027
maintained at a
relatively small
value to help
achieve an
appropriate trade-
off between
throughput and time
latency.
to OFF, the AQM
function is disabled.
enabled. In the
case, the eNodeB
would adjust the
UE-reported CQI
based on the
IBLER.
If this switch is
turned off, the CQI
adjustment
algorithm is
disabled. In this
case, the eNodeB
would not adjust the
UE-reported CQI
based on the
IBLER.
LOFD-001002 /
StepVarySwitch:
TDLOFD-001002
LOFD-00101501 /
used to enable or NO NO No
TDLOFD-00101501
disable the
LOFD-00101502 /
variable-step-based
TDLOFD-00101502
adjustment
algorithm.
If this switch is
turned on, the
variable-step-based
adjustment
algorithm is
enabled to
accelerate the
convergence of
IBLER. In this case,
rapid adjustment at
large steps is
applied if there is a
relatively large
difference between
used to enable or
disable radio link LBFD-002007 /
NO NO No
failure (RLF) LBFD-002007
detection for UL
links.
used to enable or
disable dynamic
voltage adjustment.
Indicates whether
the check on the
number of PRBs
used by GBR
services. If this
a check is
performed on
whether the number
of PRBs used by
admitted GBR
services exceeds
the related
threshold during the
LBFD-001001 /
admission
TDLBFD-001001
evaluation of a new
LBFD-002023 /
GBR service. If this
TDLBFD-002023
switch is turned off, NO NO No
LBFD-002024 /
the check is not
TDLBFD-002024
performed during
LOFD-00102901 /
the admission
TDLOFD-00102901
evaluation of a new
GBR service.
DlLdcSwitch:
Indicates whether
the downlink load
control algorithm. If
on, downlink
congestion checks
are performed and
if the cell is
congested,
corresponding
actions can be
If
IntraFreqMlbSwitch
is set to OFF, the
intra-frequency load
balancing is
disabled and
therefore
IntraFreqIdleMlbSwi
tch does not take
effect. If
InterFreqMlbSwitch
is set to ON, the
balancing is
enabled. If
LBFD-001001 /
InterFreqMlbSwitch
TDLBFD-001001
is set to OFF, the
LOFD-001032 /
TDLOFD-001032
balancing is NO NO No
LOFD-001044 /
disabled. If
TDLOFD-001044
UtranMlbSwitch is
LOFD-001045 /
set to ON, the
TDLOFD-001045
UTRAN load
balancing is
enabled. If
UtranMlbSwitch is
set to OFF, the
UTRAN load
balancing is
disabled. If
GeranMlbSwitch is
set to ON, the
GERAN load
balancing is
enabled. If
GeranMlbSwitch is
set to OFF, the
scheduling on the
PDSCH. If the
power is allocated
evenly during semi-
persistent
scheduling on the
PDSCH. If the
power control is
applied during
semi-persistent
scheduling on the
PDSCH, ensuring
communication
quality (indicated by
LBFD-002003 /
IBLER) of VoIP
TDLBFD-002003
services in the
LBFD-002009 /
QPSK modulation NO NO No
TDLBFD-002009
scheme.
LBFD-002016 /
PhichInnerLoopPcS
TDLBFD-002016
witch: Indicates the
switch for PHICH
inner-loop power
control. If the switch
is turned off, only
the initial transmit
power for the
PHICH is set. If the
the eNodeB
controls the
physical channel
transmit power to
enable the receive
SINR to converge
to the target SINR.
disable PH-based
SINR target
updates in dynamic
scheduling mode.
This switch will be
versions. In this
synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this switch.
This function is
LBFD-002009 /
incorporated into
TDLBFD-002009
inner-loop power NO NO No
LBFD-002026 /
control for PUSCH
TDLBFD-002026
in dynamic
scheduling mode.
Therefore, to
enable this function,
set
InnerLoopPuschSwi
tch to On.
InnerLoopPucchSwi
tch: If this switch is
turned off, inner-
loop power control
is not performed for
PUCCH. If this
inner-loop power
control is performed
for PUCCH.
BfSwitch: Indicates
whether to enable
or disable the
beamforming
algorithm. If the
UEs in the cell can
be served by the
beamforming
algorithm. If the TDLOFD-001049
switch is turned off, NO NO No TDLOFD-001061
UEs in the cell TDLOFD-009003
cannot be served
by the beamforming
algorithm. The
beamforming
algorithm is
disabled by default.
It must be enabled
manually if
required.
differentiation is
available. If this
service
differentiation is
unavailable.
SpsSchSwitch:
Indicates whether
semi-persistent
scheduling during
talk spurts of VoIP
services. If this
semi-persistent
scheduling is LBFD-002025 /
applied. If this TDLBFD-002025
switch is turned off, LOFD-001015 /
dynamic scheduling TDLOFD-001015
NO NO No
is applied. LOFD-001016 /
MBSFNShutDownS TDLOFD-001016
witch: Indicates LOFD-001070 /
whether to enable TDLOFD-001070
or disable
Multimedia
Broadcast Single
Frequency Network
(MBSFN) subframe
shutdown. If this
MBSFN subframe
shutdown is
available. If this
MBSFN subframe
shutdown is
unavailable. This
switch is valid only
shortens end-to-
end service delays
when the UL load is
light. Preallocation
reduces the
probability of UEs
entering DRX and
therefore shortens
the service time of
the UEs.
UlVmimoSwitch:
Indicates whether
to enable or disable LBFD-002025 /
UL MU-MIMO. If UL TDLBFD-002025
MU-MIMO is LOFD-001015 /
enabled, the TDLOFD-001015
eNodeB selects LOFD-001016 /
UEs for pairing TDLOFD-001016
according to pairing NO NO No LOFD-001002 /
rules. Then, the pair LOFD-001002
of UEs transmits LOFD-001058 /
data using the LOFD-001058
same frequency- LOFD-001048 /
time resources, TDLOFD-001048
increasing system LOFD-001067
throughput and
spectral efficiency.
TtiBundlingSwitch:
Indicates whether
TTI bundling. If TTI
bundling is enabled,
more transmission
opportunities are
available to UEs
within the delay
budget for VoIP
Indicates whether
eRAN sharing for
admission and LOFD-001036 /
scheduling. If this TDLOFD-001036
switch is turned on, LBFD-002023 /
NO NO No
operators share TDLBFD-002023
data channel LBFD-002025 /
resources TDLBFD-002025
according to the
specified
percentages.
switch.Frequency-
frequency handover
is applicable when
the eNodeB
provides dual
coverage and one
frequency is
preferred for
carrying services. If
this switch is set to
On, the frequency-
frequency handover
will be triggered
even when the
serving cell
provides a good
signal quality. If this LOFD-001032 /
NO NO No
switch is set to Off, TDLOFD-001032
the frequency-
frequency handover
is disabled.
FreqPriorIFBlindHO
Switch: Indicates
the frequency-
frequency blind
handover switch. If
this switch is set to
On, the frequency-
frequency blind
handover is
enabled. If this
switch is set to Off,
the eNodeB
used to enable or
disable the multi-
user beamforming
algorithm.
If this switch and
the switch for the
beamforming
algorithm are both LBFD-001001 /
NO NO No
turned on, the multi- TDLBFD-001001
user beamforming
algorithm is
enabled.
If this switch is
turned off, the multi-
user beamforming
algorithm is
disabled.
used to enable or
disable distance-
based handovers. If LBFD-00201804 /
this switch is turned TDLBFD-00201804
on, distance-based LOFD-001072 /
NO NO No
handovers are TDLOFD-001072
allowed. If this LOFD-001073 /
switch is turned off, TDLOFD-001073
distance-based
handovers are
prohibited.
for the access
barring algorithm. If
this parameter is
set to
ACBAR_SWITCH_
DYNAMIC, dynamic
access barring is
enabled. In this
situation, the
access probability
factor and the
average access
barring duration for
mobile-originated
calls are
dynamically
adjusted based on
LBFD-001001 /
the current cell
TDLBFD-001001
load. If this NO NO No
LBFD-002009 /
parameter is set to
TDLBFD-002009
ACBAR_SWITCH_
STATIC, static
access barring is
also enabled. In this
situation, the
access probability
factor and the
average access
barring duration for
mobile-originated
calls are configured
in the access
barring information.
set to
ACBAR_SWITCH_
DISABLE, access
used to enable or LOFD-001066 /
NO NO No
disable the UL TDLOFD-001066
CoMP algorithm.
used to enable or
disable MRC/IRC
adaptation. MRC is
short for maximum NO NO No None
ratio combining,
and IRC is short for
interference
rejection combining.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the band

division scheme
used in downlink
ICIC. The band
division in the cell is
adjusted according
to the setting of this LBFD-00202201 /
parameter so that TDLBFD-00202201
NO NO No
the edge bands for LOFD-00101401 /
neighboring cells do TDLOFD-00101401
not overlap. If this
parameter is set to
INVALID, the cell
does not distinguish
center and edge
bands.
Indicates the local

YES YES No
cell within a BS.

of the DCI power
relative to the
reference signal LBFD-002016 /
NO NO No
power when the TDLBFD-002016
PDCCH channel
carries dedicated
control information.
Indicates the local

YES YES No
cell within a BS.
Indicates the PA LBFD-002016 /
value of cell center TDLBFD-002016
NO NO No
UEs when DL ICIC LOFD-00101401 /
is enabled. TDLOFD-00101401
Indicates the PA LBFD-002016 /

value of cell edge TDLBFD-002016
NO NO No
UEs when DL ICIC LOFD-00101401 /
is enabled. TDLOFD-00101401
Indicates the local

YES YES No
cell within a BS.
Indicates the power
offset between the
PHICH TX power
LBFD-002016 /
and the RS power. NO NO No
TDLBFD-002016
This offset is used
when PHICH power
control is disabled.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
high. The QoS and
fairness among
users, however,
cannot be ensured.
The Max C/I
scheduling policy
can be used to
verify the maximum
capacity of the
system. The RR
scheduling policy is
the fairest
scheduling policy.
When RR is
adopted, the
system capacity is
the smallest.
Therefore, RR is LBFD-002025 /
used only to verify TDLBFD-002025
NO NO No
the upper bound of LOFD-001015 /
the scheduling TDLOFD-001015
fairness in the
system. In terms of
the scheduling
effect, the PF
scheduling policy is
between the
previous two
policies. Therefore,
PF can be used to
verify the capacity,
coverage, and
fairness of the
system. The EPF
scheduling policy
supports the
features such as
user QoS, system
Indicates the
percentage of free
shared RBs on the
PDSCH in
scheduling based
on pay-free users
and pay users. The
other RBs on the
PDSCH are
allocated to pay
users. When
sufficient capacity is
available, the LOFD-00101502 /
percentage of RBs TDLOFD-00101502
occupied by pay- LBFD-002023 /
NO NO No
free users and that TDLBFD-002023
occupied by pay LBFD-002024 /
users will reach the TDLBFD-002024
preset values.
Changes in this
parameter affect the
percentage of RBs
for pay-free users
and that for pay
users. Modifying
the value of this
parameter for an
active cell will lead
to the re-setup of
the cell.
of the point-to-point
(P2P) service,
which is used in
enhanced
proportional fair
(EPF) scheduling.
The value of this
parameter is used
in calculating the
priority of a UE
during scheduling
and therefore
determines the
LOFD-00101502 /
amount of physical NO NO No
TDLOFD-00101502
resources to be
allocated to the UE
that requests the
P2P service. The
P2P service priority
has a positive
value of this
parameter. This
parameter is valid
only when the
service
differentiation
function is enabled.

of the non-P2P
service used in
enhanced
proportional fair
(EPF) scheduling.
The value of this
parameter is used
in calculating the
priority of a UE
during scheduling
and therefore
determines the
amount of physical
LOFD-00101502 /
resources to be NO NO No
TDLOFD-00101502
allocated to the UE
that requests the
non-P2P service.
The priority of the
non-P2P service
has a positive
value of this
parameter. This
parameter is valid
only when the
service
differentiation
function is enabled.
Indicates the
maximum number
of layers (the rank) LOFD-001001 /
in the TDLOFD-001001
implementation of NO NO No LOFD-001003 /
multiple-input TDLOFD-001003
multiple-output LOFD-001060
(MIMO) in DL
scheduling.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
threshold for
triggering intra-
frequency load
balancing. Intra-
frequency load
balancing is started
if the cell load
exceeds the sum of
the threshold and
LBFD-001001 /
the offset, and is
TDLBFD-001001
stopped if the cell NO NO No
LOFD-001032 /
load falls below the
TDLOFD-001032
threshold.The sum
of this threshold
and the load offset
must be greater
than the sum of the
UL/DL PRB usage
threshold and
UL/DL PRB offset
shutdown.
Indicates the
threshold for
triggering inter-
frequency load
balancing. Load
balancing between
the cell and its
inter-frequency
neighboring cell is
triggered if the cell
load exceeds the
sum of this LBFD-001001 /
threshold and the TDLBFD-001001
NO NO No
offset, and is LOFD-001032 /
stopped if the cell TDLOFD-001032
load falls below this
threshold.The sum
of this threshold
and the load offset
must be greater
than the sum of the
UL/DL PRB usage
threshold and
UL/DL PRB offset
shutdown.
Indicates the
threshold for
triggering inter-RAT
load balancing.
Load balancing
between the cell
and its inter-RAT
neighboring cell is
triggered if the cell
load exceeds the
LBFD-001001 /
sum of this
TDLBFD-001001
threshold and the
LOFD-001044 /
offset, and is NO NO No
TDLOFD-001044
stopped if the cell
LOFD-001045 /
load falls below this
TDLOFD-001045
threshold.The sum
of this threshold
and the load offset
must be greater
than the sum of the
UL/DL PRB usage
threshold and
UL/DL PRB offset
shutdown.
Indicates the period
of the inter-cell load
exchange. This
parameter is
contained in the
load exchange
request message. If
the source cell
sends a load
exchange request
message containing
a period, the target
cell reports its load
to the source cell at
LBFD-001001 /
intervals based on
TDLBFD-001001
the period. If the
LOFD-001032 /
source cell sends
TDLOFD-001032
such a message NO NO No
LOFD-001044 /
without a period,
TDLOFD-001044
the target cell
LOFD-001045 /
reports its load to
TDLOFD-001045
the source cell at a
default interval of
5s. In this version,
the parameter still
supports setting
synchronization
between the M2000
and the eNodeB,
but is no longer
used internally.
Avoid using this
be removed from
later versions.

used in the
evaluation of
whether to trigger
load balancing. To
prevent load
fluctuations from LBFD-001001 /
frequently triggering TDLBFD-001001
or stopping load LOFD-001032 /
balancing, an offset TDLOFD-001032
NO NO No
needs to be set. LOFD-001044 /
That is, a specific TDLOFD-001044
load balancing LOFD-001045 /
action is taken only TDLOFD-001045
if the cell load
exceeds the sum of
the corresponding
load balancing
threshold and this
offset.
Indicates the
threshold of load
difference between
two cells for load
balancing. If the
load difference
between cells
exceeds this
threshold, the
LBFD-001001 /
eNodeB determines
TDLBFD-001001
that load imbalance
LOFD-001032 /
occurs and
TDLOFD-001032
therefore initiates NO NO No
LOFD-001044 /
load balancing
TDLOFD-001044
between the cells. If
LOFD-001045 /
the load difference
TDLOFD-001045
between cells falls
below this
threshold, the
eNodeB determines
that load imbalance
is resolved and
therefore stops load
balancing between
the cells.
used in the
evaluation of inter-
RAT load balancing.
This parameter
value multiplied by
1000 is the
threshold for the
number of UL-
synchronized users.
Load balancing
between the cell
and its inter-RAT
neighboring cell is
triggered if the
number of UL-
synchronized users
in the cell exceeds LBFD-001001 /
this threshold, and TDLBFD-001001
is stopped if the LOFD-001044 /
NO NO No
number of UL- TDLOFD-001044
synchronized users LOFD-001045 /
falls below this TDLOFD-001045
threshold. For
example, GUI value
1 is mapped to
actual value
10(1000*1%), GUI
value 2 is mapped
to actual value 20,
GUI value 10 is
mapped to actual
value 100. Note:
there is special
mapping of two GUI
values, GUI value
100 is mapped to
actual value 1 and
GUI value 99 is
Indicates the
standard duration of
the UTRAN load
LBFD-001001 /
balancing in idle
TDLBFD-001001
mode. The actual
LOFD-001044 /
duration has a NO NO No
TDLOFD-001044
LOFD-001045 /
with the number of
TDLOFD-001045
UEs in the uplink
synchronization
state.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the CCE LBFD-001001 /
aggregation level TDLBFD-001001
NO NO No
for common LBFD-002003 /
signaling. TDLBFD-002003
Indicates the CCE

ratio adjustment
switch for the
PDCCH. If this
the resource
allocation algorithm
of the PDCCH
dynamically adjusts LBFD-001001 /
the UL and DL CCE TDLBFD-001001
NO NO No
ratios within each LBFD-002003 /
transmission time TDLBFD-002003
interval (TTI) based
on CCE usages in
UL and DL. If this
the UL and DL CCE
ratios are not
dynamically
adjusted.
to the number of
OFDM symbols
occupied by the
PDCCH is turned
off, this parameter
indicates the
number of OFDM
symbols that are
always occupied by
the PDCCH.
If the switch for
dynamic adjustment
to the number of
OFDM symbols
occupied by the
PDCCH is turned
on, the number of
OFDM symbols LBFD-001001 /
occupied by the TDLBFD-001001
NO NO No
PDCCH is always 4 LBFD-002003 /
and 3 for the TDLBFD-002003
bandwidths of 1.4
MHz and 3 MHz,
respectively, and
therefore the
parameter setting is
invalid. For the
bandwidth of 5
MHz,10 MHz, 15
MHz, or 20 MHz,
this parameter is
set to 1 by default
and the number of
OFDM symbols
occupied by the
PDCCH is
adaptively adjusted
among 1, 2, and 3;
Indicates the virtual
CCE ratio for the
PDCCH. Based on
the observed
impact of different LBFD-001001 /
virtual CCE ratios TDLBFD-001001
NO NO No
on PDCCH LBFD-002003 /
demodulation TDLBFD-002003
performance, the
intra-frequency LTE
networking can be
optimized.
that is used to
control whether to
LBFD-001001 /
enable and disable
TDLBFD-001001
dynamic adjustment NO NO No
LBFD-002003 /
on the number of
TDLBFD-002003
OFDM symbols
occupied by
PDCCH.
Indicates the upper
limit for the CCE
usage within each
TTI. Note that this
parameter stops
LBFD-001001 /
taking effect if the
TDLBFD-001001
switch for NO NO No
LBFD-002003 /
dynamically
TDLBFD-002003
adjusting the
number of OFDM
symbols on the
PDCCH is turned
on.
used to enable or
disable closed-loop
adjustment to the
PDCCH
aggregation level. If
on, PDCCH
LBFD-001001 /
aggregation level is
TDLBFD-001001
adjusted based on NO NO No
LBFD-002003 /
the block error rate
TDLBFD-002003
(BLER) of the
PDCCH. If this
PDCCH
aggregation level is
not adjusted based
on the BLER of the
PDCCH.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
threshold for the
low load state of the
SRI resources. The
SRI resources enter
the low load state if
the PUCCH LBFD-002003 /
NO NO No
resource allocation TDLBFD-002003
algorithm detects
that the number of
admitted UEs is
smaller than the
value of this
parameter.
Indicates the local

ID of the cell. It
cell within a BS.
Indicates the time
when the cell no-
traffic detection
starts. If the stop
time is earlier than
or the same as the
start time, the end
time is assumed to
be a time of the
next day. If the
timer for reporting
the no-traffic alarm
is not set to 0, the
eNodeB performs
the cell no-traffic
detection from the
start time to the
stop time.
Indicates the time

when the cell no-
traffic detection
stops. If the stop
time is earlier than
or the same as the
start time, the stop
time is assumed to
be a time of the
next day. If the
timer for reporting
the no-traffic alarm
is not set to 0, the
eNodeB performs
the cell no-traffic
detection from the
start time to the
stop time.
of the timer for the
cell no-traffic
detection. If there is
no traffic in the cell
within the duration
specified by this
parameter, the
eNodeB reports the
no-access alarm
and resets the cell.
set to 0, the cell no-
traffic detection is
not performed. If
the timer for
reporting the no-
traffic alarm is set to
a non-zero value,
the eNodeB
performs the cell
no-traffic detection
from the start time
to the stop time.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the band

division scheme
used in uplink ICIC.
The band division in
the cell is changed
according to the
setting of this
LBFD-00202202 /
parameter so that
TDLBFD-00202202
the edge bands do NO NO No
LOFD-00101402 /
not overlap
TDLOFD-00101402
between
neighboring cells. If
this parameter is
set to INVALID, the
cell does not
distinguish center
and edge bands.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
Indicates the index

of a simulated load
configuration. The
value of this
parameter
corresponds to
SimuLoadCfgIndex
in a SimuLoad MO.
That is, each index
NO NO No None
corresponds to a
specific set of
parameters that
consistitute one of
the multiple
simulated load
configurations
stored in the
eNodeB.
Indicates the
transmission mode
adopted by the
simulated load
configuration for
beamforming in
TDD cells,
including:
TM1: indicates
transmission mode
1 for the simulated
load configuration
NO NO No None
TM2: indicates
transmission mode
2 for the simulated
load configuration
TM7: indicates
transmission mode
7 for the simulated
load configuration
TM8: indicates
transmission mode
8 for the simulated
load configuration
Indicates the
number of RBs
allocated by a NO NO Yes None
simulated load
configuration.
Indicates the
number of RBs for
NO NO Yes None
commercial
services in the cell.
Indicates the power
allocated by a
NO NO Yes None
simulated load
configuration.
Indicates the power
for commercial NO NO Yes None
services in the cell.
Indicates the
number of UEs
allocated by a NO NO Yes None
simulated load
configuration.
Indicates the
number of
commercial service
UEs, that is, the NO NO Yes None
number of UEs that
are actually served
by the cell.
Indicates the local
YES YES No
cell within a BS.
Indicates the
modification period
coefficient for the
BCCH. BCCH
modification period
= Modification
period coefficient x
Default paging
cycle, where the LBFD-002009 /
NO NO No
BCCH modification TDLBFD-002009
period and default
paging cycle are
measured in unit of
radio frames, and
the modification
period coefficient is
specified by this
parameter.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
Indicates the offset LBFD-002003 /

of the PCFICH TDLBFD-002003
transmit power LBFD-002009 /
NO NO No
relative to the TDLBFD-002009
power. TDLBFD-002016

of the PBCH TDLBFD-002003
transmit power LBFD-002009 /
NO NO No
relative to the TDLBFD-002009
LBFD-002003 /
of the transmit
TDLBFD-002003
power for the cell
LBFD-002009 /
synchronization NO NO No
TDLBFD-002009
signals relative to
LBFD-002016 /
TDLBFD-002016
power.

of the transmit LBFD-002003 /
power for broadcast TDLBFD-002003
information on the LBFD-002009 /
NO NO No
PDSCH channel TDLBFD-002009
relative to the LBFD-002016 /
reference signal TDLBFD-002016
power.
of the transmit TDLBFD-002003
power for the LBFD-002009 /
paging information TDLBFD-002009
NO NO No
on the PDSCH LBFD-002011 /
channel relative to TDLBFD-002011
the reference signal LBFD-002016 /

LBFD-002003 /
of the transmit
TDLBFD-002003
power for the
LBFD-002009 /
random access
TDLBFD-002009
responses on the NO NO No
LBFD-002010 /
PDSCH channel
TDLBFD-002010
relative to the
LBFD-002016 /
reference signal
TDLBFD-002016
power.

of the pilot power
LOFD-001047 /
relative to the NO NO No
TDLOFD-001047
reference signal
power.
Indicates the local
ID of the cell. It
YES YES No None
cell within a BS.
LBFD-002003 /
Indicates the
TDLBFD-002003
reference signal
LBFD-002009 /
power of the cell. NO NO No
TDLBFD-002009
For details, see
LBFD-002016 /
3GPP TS 36.213.
TDLBFD-002016
Indicates the
scaling factor index
of the Energy Per
Resource Element
LBFD-002003 /
(EPRE) on the
TDLBFD-002003
PDSCH. This
LBFD-002009 /
scaling factor is NO NO No
TDLBFD-002009
determined by the
LBFD-002016 /
value of this
TDLBFD-002016
parameter and the
antenna port. For
details, see 3GPP
TS 36.213.
Indicates the local

YES YES No
cell within a BS.
Indicates the step
by which the TX
power for random
access preambles
is increased each
time after a RACH
access failure. If
multiple attempts to
access the PRACH
LBFD-001001 /
fail, the UE
TDLBFD-001001
increases the TX NO NO No
LBFD-002026 /
power for random
TDLBFD-002026
access preambles
by a step specified
by this parameter
each time after an
access failure to
ensure successful
access.
For details, see
3GPP TS 36.321.

UE transmit power
for the PRACH
expected by the
eNodeB when
PRACH preamble LBFD-001001 /
format 0 is applied TDLBFD-001001
NO NO No
on condition that LBFD-002026 /
requirements for TDLBFD-002026
preamble detection
performance are
met.
For details, see
3GPP TS 36.321.
Indicates the
threshold for
determining the
size of Msg3 when
a UE selects a LBFD-001001 /
preamble from TDLBFD-001001
NO NO No
random access LBFD-002002 /
preamble group A TDLBFD-002002
during a random
access procedure.
For details, see
3GPP TS 36.321.

to the starting LBFD-001001 /
position of each TDLBFD-001001
NO NO No
PRACH in the LBFD-002003 /
frequency domain TDLBFD-002003
of the FDD cell.
Indicates whether
LBFD-001001 /
to configure the
TDLBFD-001001
PRACH NO NO No
LBFD-002003 /
configuration index
TDLBFD-002003
of the FDD cell.
PRACH TDLBFD-001001
NO NO No
configuration index LBFD-002003 /
of the FDD cell. TDLBFD-002003
Indicates the local

YES YES No
cell within a BS.
configuration for the
cell.
The value SCn,
where n is variable,
represents
configuration n. For
example, the value
SC0 indicates
subframe
configuration 0, and
the value SC1
indicates subframe
configuration 1. If
the cell operates in
FDD mode, the
value SC15 is
reserved. If the cell
operates in TDD LBFD-001001 /
mode, the values TDLBFD-001001
NO NO No
SC14 and SC15 LBFD-002003 /
are reserved. The TDLBFD-002003
reserved values
cannot be used. For
the relationship
between the
subframe
configuration index
and the cell-specific
subframe
cycle/offset, see
3GPP TS 36.211. In
FDD mode, this
parameter is
permanently valid.
In TDD mode, this
parameter is valid
only if
TddSrsCfgMode is
Indicates whether
the sounding
reference signal
(SRS) of a UE and
the ACK/NACK or
scheduling request
(SR) on the PUCCH
are allowed to use
the same time
resources for
simultaneous
transmission.
set to
BOOLEAN_FALSE,
simultaneous
transmission is not LBFD-001001
NO NO No
allowed. In this LBFD-002003
situation, the UE
discards the SRS
and only transmits
the ACK/NACK or
SR on the PUCCH.
set to
BOOLEAN_TRUE,
simultaneous
transmission is
allowed. In this
situation, the UE
transmits truncated
ACK/NACK or SR.
For details, see
3GPP TS 36.211.
Indicates whether a
cell has available
SRS resources. If
this parameter is
set to
BOOLEAN_TRUE,
the cell has
available SRS
resources for its
UEs. If this
BOOLEAN_FALSE, TDLBFD-001001
NO NO No
the cell has no SRS LBFD-002003 /
resources for its TDLBFD-002003
UEs. This
parameter applies
only to cells
established on an
LBBPd. If cells are
established on an
LBBPc, the cell has
available SRS
resources for its
UEs by default.
Indicates the TDD
SRS configuration
to be used. If this
parameter is set to
EXPERIENCE_FIR
ST, the TDD SRS
configuration that is
designed to
preferentially
guarantee user
experience (for
example,
beamforming
performance) is LBFD-001001 /
used. If this TDLBFD-001001
NO NO No
ACCESS_FIRST, TDLBFD-002003
the TDD SRS
configuration that is
designed to
preferentially
guarantee the
specifications (for
example, accessed
UEs and CAPs) is
used. CAP is short
for call attempt per
second. This
parameter is valid
only in TDD mode.
Indicates the cell-

LBFD-001001 /
specific SRS
TDLBFD-001001
bandwidth. For NO NO Yes
LBFD-002003 /
details, see 3GPP
TDLBFD-002003
TS 36.211.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the type
of the PHICH
duration.
set to NORMAL,
the number of
OFDM symbols
occupied by the
PDCCH can be
adaptively adjusted.
set to EXTENDED
for a cell with a 1.4
MHz bandwidth, the LBFD-002003 /
number of OFDM TDLBFD-002003
NO NO No
symbols occupied LBFD-002009 /
by the PDCCH can TDLBFD-002009
be 3 or 4. If this
parameter is set to
EXTENDED for a
cell with another
bandwidth, the
number of OFDM
symbols occupied
by the PDCCH is 3.
For the mapping
between the type
and the duration,
see 3GPP TS
36.211.
Indicates a
coefficient that is
used to calculate
the resources used
by the PHICH for
LBFD-002003 /
the cell. It
TDLBFD-002003
corresponds to the NO NO No
LBFD-002009 /
Ng parameter in the
TDLBFD-002009
protocol.
For details on the
usage of the Ng
parameter, see
3GPP TS 36.211.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
default paging
period for the cell. It
is also called the
discontinuous
reception (DRX)
period. If the EPC
specifies a DRX
period for a UE, the
UE compares this
period with the
LBFD-002009 /
value of this
TDLBFD-002009
parameter and uses NO NO No
LBFD-002011 /
the smaller one as
TDLBFD-002011
its DRX period. If
the EPC does not
specify a DRX
period, the UE uses
the value of this
parameter, which is
delivered in the
system information,
as its DRX period.
For details, see
3GPP TS 36.304.
Indicates the
number of paging
occasions
LBFD-002009 /
(subframes or times
TDLBFD-002009
of paging) NO NO No
LBFD-002011 /
contained in a
TDLBFD-002011
paging cycle.
For details, see
3GPP TS 36.304.
Indicates the local

ID of the cell. It
YES YES No None
cell within a BS.
Indicates the
LBFD-002003 /
number of PUSCH
TDLBFD-002003
sub-bands. NO NO No
LBFD-002009 /
For details, see
TDLBFD-002009
3GPP TS 36.211.
Indicates the
LBFD-002003 /
hopping mode of
TDLBFD-002003
the PUSCH. NO NO No
LBFD-002009 /
For details, see
TDLBFD-002009
3GPP TS 36.211.
Indicates the
LBFD-002003 /
hopping offset of
TDLBFD-002003
the PUSCH. NO NO No
LBFD-002009 /
For details, see
TDLBFD-002009
3GPP TS 36.211.
Indicates whether
group hopping of LBFD-002003 /
the PUSCH is TDLBFD-002003
NO NO No
enabled. LBFD-002009 /
3GPP TS 36.211.
Indicates the group
LBFD-002003 /
assignment of the
TDLBFD-002003
PUSCH. NO NO No
LBFD-002009 /
For details, see
TDLBFD-002009
3GPP TS 36.211.
Indicates whether
sequence hopping LBFD-002003 /
of the PUSCH is TDLBFD-002003
NO NO No
enabled. LBFD-002009 /
3GPP TS 36.211.
Indicates the cyclic LBFD-002003 /

shift of the PUSCH. TDLBFD-002003
NO NO No
3GPP TS 36.211. TDLBFD-002009
Indicates whether
64QAM of the
LOFD-001006 /
PUSCH is enabled. NO NO No
TDLOFD-001006
For details, see
3GPP TS 36.211.
Indicates the local
YES YES No
cell within a BS.
Indicates the cyclic

shift interval of the
PUCCH. The cyclic
shift interval of the
PUCCH can be
acquired based on
the average delay
spread of the cell,
and the average
delay spread is
acquired based on
the networking
environment. The
parameter value
LBFD-001001 /
DS1_DELTA_SHIF
TDLBFD-001001
T is not supported NO NO No
LBFD-002003 /
by the LBBPc. As a
TDLBFD-002003
result, if the cell is
established on an
LBBPc but this
parameter is set to
DS1_DELTA_SHIFT
, the value of this
parameter will be
automatically
changed to
DS2_DELTA_SHIF
T when put into
effect. For details,
see 3GPP TS
36.211.
Indicates the
number of resource
indexes allocated to
SRIs and semi- LBFD-001001 /
persistent ACKs at TDLBFD-001001
NO NO No
the RRC layer for LBFD-002003 /
the FDD cell. If this TDLBFD-002003
parameter is set to
0, UEs may fail to
access the cell.
Indicates the
LBFD-001001 /
number of RBs
TDLBFD-001001
allocated to the NO NO No
LBFD-002003 /
CQIs at the RRC
TDLBFD-002003
layer of FDD cell.
remaining 16
hexadecimal digits
cannot be set to the
same digits as the
original
configuration of a
16 decimal-digit
CGI. For example, if
the original
configuration is
1234567890123456
, the new
configuration
cannot be
1234567890123456
0000000000000000
. The CGI of an
LOFD-001036 /
external
TDLOFD-001036
CDMA2000 1xRTT
cell is 47 bits or 12
TDLOFD-001037
hexadecimal digits
LOFD-001021
in length. A 12
hexadecimal-digit
CGI is converted
from a string of
binary digits, from
the left of which the
BASEID occupies
bits 1 to 16, the SID
occupies bits 17 to
31, the NID
occupies bits 32 to
47, and 0 always
occupies bit 48. If
the length of the
BASEID, SID, and
NID is less than 16,
15, and 16 bits,
country code of the
external
CDMA2000 cell that
is shared among
multiple operators.
A PLMN ID is
LOFD-001036 /
comprised of an
TDLOFD-001036
MCC and an MNC.
The MCC consists
TDLOFD-001037
of three digits.
LOFD-001021
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code of the
external
CDMA2000 cell that
is shared among
multiple operators.
A PLMN ID is
LOFD-001036 /
comprised of an
TDLOFD-001036
MCC and an MNC.
The MCC consists
TDLOFD-001037
of three digits.
LOFD-001021
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

cell within an
eNodeB.
see the
CellGlobalIdCDMA2
000 IE defined in
section 6.3.4 of
3GPP TS 36.331.
The cell global ID
(CGI) of an external
CDMA2000 HRPD
hexadecimal digits
in length. A 16
decimal-digit CGI is
still synchronized
between the M2000
and the eNodeB in
the current version,
but is incompatible
with the protocol
and will be removed
from later versions.
Therefore, avoid
using 16 decimal-
digit CGIs. In the
new configuration
of a 32
hexadecimal-digit
CGI, if the 16
hexadecimal digits
from right to left are
all set to 0, the
remaining 16
hexadecimal digits
same digits as the
original
configuration of a
16 decimal-digit
Indicates whether
handovers of UEs LOFD-001021
to the associated NO NO No LOFD-002002 /
neighboring cell are TDLOFD-002002
prohibited.
Indicates whether
to permit or prohibit LOFD-002001 /
removal of the TDLOFD-002001
NO NO No
neighboring LOFD-002002 /
relationship by TDLOFD-002002
ANR.
Indicates the
priority of the
neighboring cell
during blind
handovers. Blind
handover is a
process in which
the eNodeB
instructs a UE to
hand over to a
specified
LOFD-002001 /
neighboring cell
TDLOFD-002001
without NO NO No
LBFD-002018 /
measurements.
TDLBFD-002018
There are 32
priorities altogether.
The priority has a
with the value of
this parameter.
Note that the value
0 indicates that
blind handovers to
are prohibited.
Indicates whether
LOFD-002001 /
this neighboring cell
TDLOFD-002001
is automatically NO NO No
LOFD-002002 /
discovered by the
TDLOFD-002002
ANR algorithm.
LOFD-002001 /
Indicates the name TDLOFD-002001
NO NO No
of the local cell. LOFD-002002 /
TDLOFD-002002
of the neighboring TDLOFD-002001
NO NO No
CDMA2000 HRPD LOFD-002002 /
cell. TDLOFD-002002

cell within an
eNodeB.
Indicates the
neighboring
CDMA2000 band
class. Signals on a
LOFD-001021
frequency within the
LBFD-00201803 /
band class can be YES YES No
TDLBFD-00201803
obtained by UEs.
LOFD-002002
BandclassCDMA20
00 IE defined in
3GPP 36.331 6.3.4.
Indicates the
neighboring
CDMA2000
frequency of the LOFD-001021
serving cell. For LBFD-00201803 /
YES YES No
details, see the IE TDLBFD-00201803
CDMA2000- LOFD-002002
CarrierInfo in the
3GPP 36.331 6.3.4
protocol.
Indicates the
frequency-specific
offset of the local
cell to the
neighboring
CDMA2000 cell on
the frequency. A
LOFD-001021
parameter leads to NO NO No
LOFD-002002
of triggering
measurement
reports. For details,
see the Q-
OffsetRangeInterRA
T IE defined in
3GPP 36.331 6.3.4.
Indicates whether
to set the size of
the CDMA2000
LBFD-001001 /
search window. If
this parameter is
LOFD-001021
set to NOT_CFG,
the default size (8)
is used.

the CDMA2000
search window.
UEs search for
pilots for
neighboring
CDMA2000 cells LBFD-001001
NO NO No
within the time LOFD-001021
period specified by
this parameter. For
details, see the
MeasObjectCDMA2
000 IE defined in
3GPP TS 36.331.
country code of the
external cell.
A PLMN ID is
comprised of an
MCC and an MNC.
LOFD-001036 /
The MCC consists
TDLOFD-001036
of three digits. YES YES No
LOFD-001037 /
The MNC consists
TDLOFD-001037
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code of the
external cell.
A PLMN ID is
comprised of an
MCC and an MNC.
LOFD-001036 /
The MCC consists
TDLOFD-001036
LOFD-001037 /
The MNC consists
TDLOFD-001037
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
Indicates the
eNodeB identity of
the external E-
UTRAN cell. It
uniquely identifies
an eNodeB within a
PLMN. The 28-bit
E-UTRAN cell
identity is
comprised of the LOFD-001036 /
cell identity and the TDLOFD-001036
YES YES No
eNodeB identity LOFD-001037 /
(represented by the TDLOFD-001037
most significant 20
bits). The cell global
identity (CGI) of an
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
Indicates the cell
identity of the
external E-UTRAN
cell. It uniquely
identifies a cell
within an eNodeB.
The 28-bit E-
UTRAN cell identity
is comprised of the
cell identity LOFD-001036 /
(represented by the TDLOFD-001036
YES YES No
least significant LOFD-001037 /
eight bits) and the TDLOFD-001037
eNodeB identity.
The cell global
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.

country code of the
external E-UTRAN
cell that is shared
among multiple
operators.
A PLMN ID is
comprised of an LOFD-001036 /
MCC and an MNC. TDLOFD-001036
YES YES No
The MCC consists LOFD-001037 /
of three digits. TDLOFD-001037
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
network code of the
external E-UTRAN
cell that is shared
among multiple
operators.
A PLMN ID is
YES YES No
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
Indicates the
identity of the LOFD-001036 /
external GERAN TDLOFD-001036
YES YES No
cell. It uniquely LOFD-001037 /
identifies a GERAN TDLOFD-001037
cell within a PLMN.
LOFD-001036 /
Indicates the LAC
TDLOFD-001036
of the external YES YES No
LOFD-001037 /
GERAN cell.
TDLOFD-001037

country code of the
external cell.
A PLMN ID is
comprised of an
MCC and an MNC.
LOFD-001036 /
The MCC consists
TDLOFD-001036
LOFD-001037 /
The MNC consists
TDLOFD-001037
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
network code of the
external cell.
A PLMN ID is
comprised of an
MCC and an MNC.
LOFD-001036 /
The MCC consists
TDLOFD-001036
LOFD-001037 /
The MNC consists
TDLOFD-001037
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

country code of the
external GERAN
cell that is shared
among multiple
operators.
A PLMN ID is
YES YES No
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code of the
external GERAN
cell that is shared
among multiple
operators.
A PLMN ID is
YES YES No
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
Indicates the ID of
the external UTRAN
cell. It uniquelly
identifies a cell in a
PLMN. The 28-bit
ID of the external
UTRAN cell
consists of a 12-bit
RNC ID (indicated
LOFD-001036 /
by RncId) and a 16-
TDLOFD-001036
bit RNC cell ID YES YES No
LOFD-001037 /
(indicated by
TDLOFD-001037
RncCellId). The
formula for
calculating the ID of
the external UTRAN
cell is as follows:
External UTRAN
cell ID = RNC ID x
65536 + RNC cell
ID.

country code of the
external UTRAN
cell.
A PLMN ID is
comprised of an
MCC and an MNC. LOFD-001036 /
The MCC consists TDLOFD-001036
YES YES No
of three digits. LOFD-001037 /
The MNC consists TDLOFD-001037
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code of the
external UTRAN
cell.
A PLMN ID is
comprised of an
MCC and an MNC. LOFD-001036 /
The MCC consists TDLOFD-001036
YES YES No
of three digits. LOFD-001037 /
The MNC consists TDLOFD-001037
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
country code of the
external UTRAN
cell that is shared
among multiple
operators.
A PLMN ID is
YES YES No
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code of the
external UTRAN
cell that is shared
among multiple
operators.
A PLMN ID is
YES YES No
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
remaining 16
hexadecimal digits
same digits as the
original
configuration of a
16 decimal-digit
the original
configuration is
1234567890123456
, the new
configuration
cannot be
1234567890123456
0000000000000000
. The CGI of an
external
CDMA2000 1xRTT
hexadecimal digits
in length. A 12
hexadecimal-digit
CGI is converted
from a string of
binary digits, from
BASEID occupies
occupies bits 17 to
31, the NID
occupies bits 32 to
47, and 0 always
occupies bit 48. If
the length of the
BASEID, SID, and
15, and 16 bits,
Indicates the band

class on which the LOFD-001021
external LBFD-00201803 /
CDMA2000 cell NO YES No TDLBFD-00201803
operates. For LOFD-002002 /
TS 36.331.
Indicates the
frequency on which LOFD-001021
the external LBFD-00201803 /
CDMA2000 cell NO YES No TDLBFD-00201803
operates. For LOFD-002002 /
TS 36.331.
Indicates the
scrambling code, LBFD-001001 /
which is used as TDLBFD-001001
the physical cell NO YES No LOFD-001021
identifier of the LBFD-00201803 /
external TDLBFD-00201803
CDMA2000 cell.
Indicates the type

of the external
CDMA2000 cell. By
default, the cell is a
CDMA2000 HRPD
cell.
Note that the cell LOFD-001021
global identity of a NO NO No LBFD-00201803 /
CDMA2000 1xRTT TDLBFD-00201803
cell consists of 6
decimal digits, and
that of a
CDMA2000 HRPD
cell consists of 16
decimal digits.

country code of the
external cell.
A PLMN ID is
comprised of an
MCC and an MNC. LOFD-001021
of three digits. NO YES No TDLOFD-001036
The MNC consists LOFD-001037 /
of two to three TDLOFD-001037
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code of the
external cell.
A PLMN ID is
comprised of an
MCC and an MNC. LOFD-001021
of three digits. NO YES No TDLOFD-001036
The MNC consists LOFD-001037 /
of two to three TDLOFD-001037
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
LOFD-001021
of the external NO NO No TDLBFD-00201803
CDMA2000 cell. LOFD-002002 /
TDLOFD-002002

cell within an
eNodeB.
hexadecimal digits
in length. A 12
hexadecimal-digit
CGI is converted
from a string of
binary digits, from
BASEID occupies
occupies bits 17 to
31, the NID
occupies bits 32 to
47, and 0 always
occupies bit 48. If
the length of the
BASEID, SID, and
15, and 16 bits,
respectively, YES YES No LOFD-001021
supplement zeros
to the left of each
ID. A 6 decimal-digit
CGI is still
synchronized
between the M2000
and the eNodeB in
the current version,
but is incompatible
with the protocol
and will be removed
from later versions.
Therefore, avoid
using 6 decimal-
digit CGIs. In the
new configuration
of a 12
hexadecimal-digit
Indicates whether
handovers of UEs LOFD-001021
to the associated NO NO No LOFD-002002 /
neighboring cell are TDLOFD-002002
prohibited.
Indicates whether
NO NO No
ANR.
Indicates the
priority of the
neighboring cell
during blind
handovers. Blind
handover is a
process in which
the eNodeB
instructs a UE to
hand over to a
specified
LOFD-002001 /
neighboring cell
TDLOFD-002001
without NO NO No
LBFD-002018 /
measurements.
TDLBFD-002018
There are 32
The priority has a
with the value of
this parameter.
Note that the value
0 indicates that
blind handovers to
are prohibited.
Indicates whether
LOFD-002001 /
TDLOFD-002001
LOFD-002002 /
discovered by the
TDLOFD-002002
ANR algorithm.
LOFD-002001 /
NO NO No
TDLOFD-002002
of the neighboring NO NO No TDLOFD-002001
cell. LOFD-002002

cell within an
eNodeB.
Indicates the
neighboring
CDMA2000 band
class. Signals on a
LOFD-001021
frequency within the
LBFD-00201803 /
band class can be YES YES No
TDLBFD-00201803
obtained by UEs.
LOFD-002002
BandclassCDMA20
00 IE defined in
3GPP 36.331.
Indicates the
absolute priority of
the CDMA2000
band class to be
used during cell
reselection. The
value 0 indicates
LOFD-001021
Frequencies used
for different RATs
TDLBFD-00201803
must be assigned
different cell
reselection
priorities. The
information is
contained in SIB8.
For details, see
3GPP TS 36.331.
Indicates the
minimum RX level
required for a
neighboring cell on
a frequency in the
CDMA2000 band
class to become a
candidate for
reselection if the
priority of the
frequency is higher
than that of the
serving frequency.
After
LBFD-00201803 /
measurements are NO NO No
TDLBFD-00201803
started for
neighboring cells on
a frequency in the
band class, the UE
reselects to a
neighboring cell
only if the RX level
of the cell is higher
than the value
specified by this
parameter for a
time-to-trigger. For
details, see 3GPP
TS 36.304 5.2.4.5.
Indicates the
minimum RX level
required for a
neighboring cell on
a frequency in the
CDMA2000 band
class to become a
candidate for
reselection if the
priority of the
frequency is lower
than that of the
serving frequency.
After
measurements are
started for LBFD-00201803 /
NO NO No
neighboring cells on TDLBFD-00201803
a frequency in the
band class, the UE
reselects to a cell
on the frequency
only if the RX level
of the serving cell is
lower than a
specified threshold
and that of the cell
is higher than the
value specified by
this parameter for a
details, see 3GPP
TS 36.304 5.2.4.5.

country code of the
external cell.
The PLMN consists
of the MCC and the
MNC.
YES YES No
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
network code of the
external cell.
The PLMN consists
of the MCC and the
MNC.
YES YES No
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.

of the external
GERAN cell. It
GERAN cell within
LOFD-001020 /
the area specified YES YES No
TDLOFD-001020
by the location area
identity (LAI). An
LAI consists of the
MCC, MNC, and
LAC.
Indicates the LAC

of the external
GERAN cell. It LOFD-001020 /
YES YES No
location within a
PLMN.
Indicates whether
to set the routing
area code (RAC) of
the external
GERAN cell. This
LOFD-001020 /
parameter is NO NO No
TDLOFD-001020
required if the
external GERAN
cell supports packet
switched (PS)
services.
NO NO No
routing area code. TDLOFD-001020
Indicates the
GERAN band
indicator. If the
GERAN ARFCN is
a value in the range
LOFD-001020 /
of 512 to 810, the
TDLOFD-001020
value of this
LOFD-001023 /
parameter is used
TDLOFD-001023
to indicate whether
LOFD-001034 /
the GERAN ARFCN
TDLOFD-001034
is in the 1800 MHz NO YES No
LOFD-001046 /
band or the 1900
TDLOFD-001046
MHz band. If the
LOFD-001073 /
GERAN ARFCN is
TDLOFD-001073
not in either band,
LOFD-001045 /
this parameter does
TDLOFD-001045
not take effect and
can be set to either
value. For details,
see 3GPP TS
36.331.
LOFD-001020 /
TDLOFD-001020
Indicates the
LOFD-001045 /
GERAN BCCH
TDLOFD-001045
ARFCN. For details, NO YES No
LOFD-001046 /
see 3GPP TS
TDLOFD-001046
45.005.
LOFD-001073 /
TDLOFD-001073
Indicates the
network color code
(NCC) of GERAN. It
is operator-specific
and identifies a LOFD-001020 /
network within the TDLOFD-001020
whole country. LOFD-001045 /
The base TDLOFD-001045
NO YES No
transceiver station LOFD-001046 /
identity code (BSIC) TDLOFD-001046
consists of the NCC LOFD-001073 /
and the base TDLOFD-001073
station color code
(BCC). For details,
see 3GPP TS
23.003.
Indicates the base

station color code
(BCC) of the LOFD-001020 /
external GERAN TDLOFD-001020
cell. The base LOFD-001045 /
transceiver station TDLOFD-001045
NO YES No
identity code (BSIC) LOFD-001046 /
consists of the BCC TDLOFD-001046
and the network LOFD-001073 /
color code (NCC). TDLOFD-001073
For details, see
3GPP TS 23.003.
Indicates whether
the cell supports
the dual
transmission mode.
LOFD-001020 /
If the cell supports
TDLOFD-001020
the dual
LOFD-001045 /
transmission mode,
TDLOFD-001045
both CS and PS NO NO No
LOFD-001046 /
services can be
TDLOFD-001046
handed over to the
LOFD-001073 /
cell. Otherwise, only
TDLOFD-001073
the CS service or
the PS service can
be handed over to
the cell.
Indicates the name
LOFD-001020 /
of the external NO NO No
TDLOFD-001020
GERAN cell.
Indicates whether
the external
GERAN cell
supports single
radio voice call
LOFD-001020 /
continuity (SRVCC)
TDLOFD-001020
for both CS and PS NO NO No
LOFD-001046 /
services. If this
TDLOFD-001046
parameter is set to
BOOLEAN_FALSE,
the cell supports
only SRVCC for CS
services.

cell within an
eNodeB.
country code of the
neighboring
GERAN cell.
The PLMN consists
of the MCC and the
MNC.
LOFD-001020 /
The MCC consists YES YES No
TDLOFD-001020
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.

network code of the
neighboring
GERAN cell.
The PLMN consists
of the MCC and the
MNC.
LOFD-001020 /
TDLOFD-001020
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
Indicates the LAC

of the GERAN
neighboring cell. It LOFD-001020 /
YES YES No
location within a
PLMN.

of the GERAN
neighboring cell. It
GERAN cell within
LOFD-001020 /
the area specified YES YES No
TDLOFD-001020
by the location area
identity (LAI). An
LAI consists of the
MCC, MNC, and
LAC.
Indicates whether
to permit or prohibit
LOFD-002001 /
removal of the
neighboring
LOFD-002002
relationship by
ANR.
Indicates whether
handovers of UEs
to the neighboring
cell are prohibited.
Indicates the
priority of the
neighboring cell
during blind
handovers. Blind
handover is a
process in which
LBFD-002018 /
the eNodeB
TDLBFD-002018
instructs a UE to
LOFD-001020 /
hand over to a
TDLOFD-001020
specified
LOFD-001045 /
neighboring cell. NO NO No
TDLOFD-001045
There are 32
LOFD-001046 /
TDLOFD-001046
The priority has a
LOFD-001073 /
TDLOFD-001073
with the value of
this parameter.
Note that the value
0 indicates that
blind handovers to
are not allowed.
Indicates whether
this neighboring cell LOFD-002001 /
is automatically NO NO No TDLOFD-002001
discovered by the LOFD-002002
ANR algorithm.
LOFD-002001 /
NO NO No
TDLOFD-002002
of the GERAN NO NO No TDLOFD-002001
neighboring cell. LOFD-002002
Indicates the ID of
the eNodeB, which
LOFD-001053 /
uniquely identifies NO NO Yes
TDLOFD-001053
an eNodeB within a
PLMN.
Indicates the start
time of the latest
RIM procedure LOFD-001053 /
NO NO Yes
towards the TDLOFD-001053
neighboring
GERAN cell.
Indicates the time
of the latest RIM
LOFD-001053 /
request received by NO NO Yes
TDLOFD-001053
the neighboring
GERAN cell.

cell within an
eNodeB.
Indicates a GERAN
carrier frequency
group. In the cell
reselection
procedure, the
GERAN carrier
frequencies are LOFD-001020 /
YES YES No
organized in groups TDLOFD-001020
and the cell
reselection
parameters are
provided per group
of GERAN carrier
frequencies.
LOFD-001020 /
TDLOFD-001020
Indicates the
LOFD-001045 /
standard that is
TDLOFD-001045
supported by the NO YES No
LOFD-001046 /
current carrier
TDLOFD-001046
frequency group.
LOFD-001073 /
TDLOFD-001073
LOFD-001020 /
Indicates the first TDLOFD-001020
ARFCN value in the LOFD-001045 /
GERAN carrier TDLOFD-001045
NO YES No
frequency group. LOFD-001046 /
For details, see TDLOFD-001046
3GPP TS 36.331. LOFD-001073 /
TDLOFD-001073
Indicates the
GERAN band
indicator. If the
GERAN ARFCN is
a value in the range
of 512 to 810, the
value of this
LOFD-001020 /
parameter is used
TDLOFD-001020
to indicate whether
LOFD-001045 /
the GERAN ARFCN
TDLOFD-001045
is in the 1800 MHz NO YES No
LOFD-001046 /
band or the 1900
TDLOFD-001046
MHz band. If the
LOFD-001073 /
GERAN ARFCN is
TDLOFD-001073
not in either band,
this parameter does
not take effect and
can be set to either
value. For details,
see 3GPP TS
36.331.
Indicates whether
to set the
of the frequencies
in the GERAN
carrier frequency
group. If the value
LBFD-00201803 /
of this parameter is NO NO No
TDLBFD-00201803
not specified, the
UE does not
reselect to
the frequencies in
the GERAN carrier
frequency group.
the GERAN carrier
frequency group
based on the value
of this parameter
and the absolute
priority of the
serving cell.
If the value of this
parameter is larger
than the absolute
priority of the
serving cell, the UE
starts
measurements on
the frequencies in
the GERAN carrier
frequency group;
then if the signal LBFD-00201803 /
NO NO No
quality of some TDLBFD-00201803
neighboring cells
meets the related
conditions, the UE
starts cell
reselection. If the
value of this
parameter is
smaller than the
the serving cell, the
UE starts the
measurements only
when the signal
quality of the
serving cell is poor;
then if the signal
quality of some
neighboring cells
Indicates whether
to set the maximum
power that the UE
can apply to
transmission on a
frequency in the
GERAN carrier LBFD-00201803 /
NO NO No
frequency group. It TDLBFD-00201803
is used in criteria S
to calculate the
compensated
power. For details,
see 3GPP TS
36.104.
Indicates the
maximum power
that the UE can
apply to
transmission on a LBFD-00201803 /
NO NO No
frequency in the TDLBFD-00201803
GERAN carrier
frequency group.
For details, see
3GPP TS 36.331.
Indicates the RX
level required for a
neighboring cell on
a frequency in the
GERAN carrier
frequency group to
become a
candidate for
selection. It is
S and used in the
evaluation for cell
selection. During
the evaluation for
cell reselection, the
UE performs the
following
calculation: Srxlev = LBFD-00201803 /
NO NO No
Measured RSSI TDLBFD-00201803
value of a
neighboring cell on
a frequency in the
GERAN carrier
frequency group -
Value of this
parameter -
Compensated
power. If Srxlev for
a neighboring cell is
better than a
threshold for a time-
to-trigger,
reselection to the
cell is started. For
details, see 3GPP
TS 36.104.
Indicates the RX
neighboring cell on
a frequency in the
GERAN carrier
frequency group to
become a
candidate for
reselection if the
priority of the
frequency is higher
than that of the
serving frequency.
After
measurements are LBFD-00201803 /
NO NO No
started for TDLBFD-00201803
a frequency in the
GERAN carrier
frequency group,
the UE reselects to
a cell on the
frequency only if
the RX level of the
cell is better than
the value specified
by this parameter
for a time-to-trigger.
For details, see
3GPP TS 36.104.
Indicates the RX
neighboring cell on
a frequency in the
GERAN carrier
frequency group to
become a
candidate for
reselection if the
priority of the
frequency is lower
than that of the
serving frequency.
After
measurements are
started for
neighboring cells on LBFD-00201803 /
NO NO No
a frequency in the TDLBFD-00201803
GERAN carrier
frequency group,
the UE reselects to
a cell on the
frequency only if
the RX level of the
serving cell is lower
than a specified
threshold and that
of the cell is better
than the value
specified by this
parameter for a
details, see 3GPP
TS 36.104.
Indicates the
frequency specific
offset of the group
of neighboring
GERAN carrier
frequencies. This
LOFD-001020 /
parameter is used
in the decision of
LOFD-002002
the UE to send
measurement
reports for inter-
RAT handovers. For
details, see 3GPP
TS 36.331.
Indicates whether a
BCCH carrier with
the specific NCC is
LBFD-00201803 /
permitted for NO NO No
TDLBFD-00201803
monitoring. For
details, see 3GPP
TS 36.331.

cell within an
eNodeB.
Indicates the index
of the BCCH carrier LBFD-002009 /
frequency group. It TDLBFD-002009
YES YES No
identifies a BCCH LOFD-001020 /
carrier frequency TDLOFD-001020
group.
Indicates the
LBFD-002009 /
GERAN BCCH
TDLBFD-002009
ARFCN. For details, YES YES No
LOFD-002002 /
see 3GPP TS
TDLOFD-002002
45.005.

cell within an
eNodeB.
Indicates the
starting physical cell
LBFD-00201803 /
ID of the intra-
TDLBFD-00201803
frequency YES YES No
LBFD-00201801 /
blacklisted cell. For
TDLBFD-00201801
details, see 3GPP
TS 36.331.

of the intra- TDLBFD-00201803
NO NO No
frequency LBFD-00201801 /
blacklisted cell. TDLBFD-00201801
Indicates the
physical cell ID
LBFD-00201803 /
range of the intra-
TDLBFD-00201803
frequency NO NO No
LBFD-00201801 /
TDLBFD-00201801
details, see 3GPP
TS 36.331.

cell within an
eNodeB.

country code of the
E-UTRAN
neighboring cell.
The PLMN consists
of the MCC and the
MNC.
LBFD-00201801 /
TDLBFD-00201801
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.

network code of the
E-UTRAN
neighboring cell.
The PLMN consists
of the MCC and the
MNC.
LBFD-00201801 /
TDLBFD-00201801
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
Indicates the
eNodeB identity of
the intra-frequency
uniquely identifies
an eNodeB within a
PLMN. The 28-bit
E-UTRAN cell
identity is
comprised of the
cell identity and the LBFD-00201801 /
YES YES No
eNodeB identity TDLBFD-00201801
(represented by the
most significant 20
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
Indicates the local

identity of the intra-
frequency
cell within an
eNodeB. The 28-bit
E-UTRAN cell
identity is
comprised of the
cell identity
LBFD-00201801 /
(represented by the YES YES No
TDLBFD-00201801
least significant
eight bits) and the
eNodeB identity.
The cell global
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
Indicates the cell
individual offset for
the intra-frequency
neighboring cell,
which is used in
evaluation for
handovers. It LBFD-00201801 /
affects the TDLBFD-00201801
probability of LOFD-002005 /
NO NO No
triggering intra- TDLOFD-002005
reports. A larger
value of this
parameter indicates
For details, see
3GPP TS 36.331.

for the intra-
frequency
neighboring cell,
which is used in
evaluation for cell
reselections. A
LBFD-00201803 /
larger value of this NO NO No
TDLBFD-00201803
a lower probability
of cell reselections.
This parameter is
contained in SIB4.
For details, see
3GPP TS 36.331.
LBFD-00201801 /
TDLBFD-00201801
handovers of UEs TDLOFD-002001
NO NO No
to the neighboring LOFD-002002 /
cell are prohibited. TDLOFD-002002
LOFD-002012 /
TDLOFD-002012

to permit or prohibit TDLOFD-002001
removal of the LOFD-002002 /
NO NO No
neighboring TDLOFD-002002
relationship by LOFD-002012 /
ANR. TDLOFD-002012
Indicates whether
LOFD-002001 /
TDLOFD-002001
discovered by the
ANR algorithm.
Indicates the name LBFD-00201801

NO NO No
of the local cell. LOFD-002001
Indicates the name
of the intra-
frequency
neighboring E-
UTRAN cell. The
name is a string of
a maximum of 99
characters. The
null characters or
contain any of the
following LBFD-00201801 /
characters: double TDLBFD-00201801
NO NO No
quotation marks ("), LOFD-002001 /
commas (,), TDLOFD-002001
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).

cell within an
eNodeB.
Band 13: DL
EARFCN range:
5180 to 5289,
lowest frequency of
the DL operating
band: 746;
Band 14: DL
EARFCN range:
5280 to 5379,
lowest frequency of
the DL operating
band: 758;
Band 17: DL
EARFCN range:
5730 to 5849,
lowest frequency of
the DL operating LBFD-001001 /
band: 734; TDLBFD-001001
Band 18: DL LBFD-00201803 /
YES YES No
EARFCN range: TDLBFD-00201803
5850 to 5999, LBFD-00201802 /
lowest frequency of TDLBFD-00201802
the DL operating
band: 860;
Band 19: DL
EARFCN range:
6000 to 6149,
lowest frequency of
the DL operating
band: 875;
Band 20: DL
EARFCN range:
6150 to 6449,
lowest frequency of
the DL operating
band: 791;
Band 21: DL
EARFCN range:
Indicates whether
to set the UL
EARFCN. If this
NOT_CFG, the UL TDLBFD-001001
EARFCN is the DL LBFD-00201803 /
NO NO No
EARFCN plus TDLBFD-00201803
18000 in FDD LBFD-00201802 /
mode and is the TDLBFD-00201802
same as the DL
EARFCN in TDD
mode.
23010 to 23179,
lowest frequency of
the UL operating
band: 699;
Band 13: UL
EARFCN range:
23170 to 23279,
lowest frequency of
the UL operating
band: 776;
Band 14: UL
EARFCN range:
23280 to 23379,
lowest frequency of
the UL operating
band: 788;
Band 17: UL LBFD-001001 /
EARFCN range: TDLBFD-001001
23730 to 23849, LBFD-00201803 /
NO NO No
lowest frequency of TDLBFD-00201803
the UL operating LBFD-00201802 /
band: 704; TDLBFD-00201802
Band 18: UL
EARFCN range:
23850 to 23999,
lowest frequency of
the UL operating
band: 815;
Band 19: UL
EARFCN range:
24000 to 24149,
lowest frequency of
the UL operating
band: 830;
Band 20: UL
EARFCN range:
24150 to 24449,
lowest frequency of
Indicates whether
to set the
of the neighboring
E-UTRAN
frequency. If the LBFD-00201803 /
NO NO No
parameter is not
specified, the UE
does not reselect to
the frequency.
a neighboring cell
on the frequency
based on the value
of this parameter
and the absolute
priority of the
serving cell.
parameter is larger
than the absolute
priority of the
starts
measurements on
the frequency; then
if the signal quality
of some
NO NO No
meets the related TDLBFD-00201803
conditions, the UE
starts cell
reselection.
parameter is less
UE starts the
measurements only
when the signal
quality of the
then if the signal
quality of some
neighboring cells
meets the related
conditions, the UE
Indicates the time

frequency cell
reselection. A UE
initiates a
reselection to the
inter-frequency
neighboring cell
only after the signal
quality in the cell is
better than that in LBFD-00201803 /
NO NO No
the serving cell for TDLBFD-00201803
a period defined by
this parameter and,
in addition, after the
UE camps on the
serving cell for
longer than 1s. This
parameter is
contained in SIB5.
For details, see
3GPP TS 36.331.
Indicates whether
to set the speed-
dependent scaling
parameters related
to cell reselection.
LBFD-00201803 /
If this parameter is NO NO No
TDLBFD-00201803
set to NOT_CFG,
speed-dependent
cell reselections are
not supported by
default.
Indicates the
scaling factor
applied to the cell
for medium-mobility LBFD-00201803 /
NO NO No
UEs. This TDLBFD-00201803
parameter is
delivered in SIB5.
For details, see
3GPP TS 36.331.
Indicates the
scaling factor
applied to the cell
for high-mobility LBFD-00201803 /
NO NO No
UEs. This TDLBFD-00201803
parameter is
delivered in SIB5.
For details, see
3GPP TS 36.331.
Indicates the
measurement
bandwidth of the
inter-frequency
neighboring cell on
the frequency. The
setting of this
LBFD-001001 /
parameter depends
TDLBFD-001001
on the bandwidth
LOFD-001032 /
configuration of the
TDLOFD-001032
cell. In E-UTRAN, a
LBFD-00201802 /
cell bandwidth is
NO YES No TDLBFD-00201802
also expressed in
LBFD-00201803 /
units of resource
TDLBFD-00201803
blocks (RBs). Cell
LBFD-00201804 /
bandwidths 1.4
TDLBFD-00201804
MHz, 3 MHz, 5
LBFD-00201805
MHz, 10 MHz, 15
MHz, and 20 MHz
correspond to 6
RBs, 15 RBs, 25
RBs, 50 RBs, 75
RBs, and 100 RBs,
respectively.
Indicates the
frequency offset of
LBFD-001001 /
TDLBFD-001001
on the frequency. It
LOFD-001032 /
is delivered in
TDLOFD-001032
system information
LBFD-00201802 /
block type 5 (SIB5).
It is used in the
LBFD-00201803 /
evaluation for cell
TDLBFD-00201803
reselection and for
LBFD-00201804 /
the triggering and
TDLBFD-00201804
stopping of event
LBFD-00201805
A4. For details, see
3GPP TS 36.331.
Indicates the RX
neighboring cell on
the frequency to
become a
candidate for
reselection if the
priority of the
frequency is higher
than that of the
serving frequency.
After
measurements are
LBFD-00201803 /
started for NO NO No
TDLBFD-00201803
the frequency, the
UE reselects to a
neighboring cell on
the frequency only
if the RX level of
the cell is better
than the value
specified by this
parameter for a
details, see 3GPP
TS 36.331.
Indicates the
minimum RX level
required for a
neighboring cell on
the frequency to
become a
candidate for
reselection if the
priority of the
frequency is lower
than or equal to that
of the serving
frequency. After
measurements are
started for
LBFD-00201803 /
neighboring cells on NO NO No
TDLBFD-00201803
the frequency, the
UE reselects to a
neighboring cell on
the frequency only
if the RX level of
the serving cell is
lower than a
specified threshold
is higher than the
value specified by
details, see 3GPP
TS 36.331.
Indicates the RX
neighboring cell on
the frequency to
become a suitable
cell for selection. It
is included in
criteria S and used
in the evaluation for
cell selection.
During the
evaluation for cell
reselection, the UE
performs the
following
LBFD-00201803 /
calculation: Srxlev = NO NO No
TDLBFD-00201803
Measured RSRP
value of a
neighboring cell on
the frequency -
Value of this
parameter -
Compensated
a cell is better than
a threshold for a
time-to-trigger,
reselection to the
details, see 3GPP
TS 36.304.
Indicates whether
to set the maximum
power that the UE
can apply to
transmission on the
neighboring E-
UTRAN frequency.
LBFD-00201803 /
If the value of this NO NO No
TDLBFD-00201803
parameter is not
specified, the
maximum power is
subject to the UE
capability. For
details, see 3GPP
TS 36.101.
Indicates the
maximum power
that the UE can
apply to
transmission on the
neighboring E-
UTRAN frequency.
It is used in criteria
S to calculate the LBFD-00201803 /
NO NO No
compensated TDLBFD-00201803
power. If the value
not specified, the
maximum power is
subject to the UE
capability. For
details, see 3GPP
TS 36.101.
Indicates the
configuration
information about
the intra-frequency
neighboring cell of
the serving cell.
BitString00:
Indicates that
certain neighboring
cells have the same
MBSFN subframe.
BitString01:
Indicates that all
have the same TDLBFD-00201803
NO NO No
MBSFN subframe. LBFD-00201802 /
BitString10: TDLBFD-00201802
Indicates that all
neighboring cells
have mutually
different MBSFN
subframes.
BitString11:
Indicates that the
serving TDD cells
have neighboring
cells of different UL-
DL configurations.
For details, see
3GPP TS 36.331.
Indicates whether
all inter-frequency
this frequency are
configured with at
least two antenna
ports.
Set this parameter
to TRUE if all inter-
NO NO No
this frequency are LBFD-00201802 /
configured with at TDLBFD-00201802
least two antenna
ports.
Set this parameter
to FALSE if one
inter-frequency
neighboring cell on
this frequency is
configured with only
one antenna port.
Indicates the event

to trigger coverage-
based inter-
frequency
handovers. This
parameter can be
set to EventA3,
EventA4, or
EventA5. If the
neighboring E-
UTRAN frequency LOFD-001032 /
and the serving TDLOFD-001032
frequency are in the LBFD-00201802 /
same frequency NO NO No TDLBFD-00201802
band, event A3 is LBFD-00201804 /
recommended as it TDLBFD-00201804
provides better LBFD-00201805
handover
performance in this
situation. If the
neighboring E-
UTRAN frequency
and the serving
frequency are in
different frequency
bands, event A4 or
A5 is used.
Indicates the
RSRQ-based
minimum RX level
required for a
neighboring cell on
the frequency to
become a
candidate for
reselection if the
RSRQ-based
priority of the
frequency is higher
than that of the
serving frequency.
After
NO NO No
the neighboring E-
UTRAN frequency,
the UE reselects to
a neighboring cell
on the frequency
only if the RSRQ-
based RX level of
the cell is higher
than the value
specified by this
parameter for a
details, see 3GPP
TS 36.331.
Indicates the
RSRQ-based
minimum RX level
required for a
neighboring cell on
the frequency to
become a
candidate for
reselection if the
RSRQ-based
priority of the
frequency is lower
than that of the
serving frequency.
After
measurements are
started for
neighboring cells on LBFD-00201803 /
NO NO No
a frequency in the TDLBFD-00201803
GERAN carrier
frequency group,
the UE reselects to
a neighboring cell
on the frequency
only if the RSRQ-
based RX level of
the serving cell is
lower than a
specified threshold
is higher than the
value specified by
details, see 3GPP
TS 36.331.
Indicates whether
LBFD-00201803 /
to set the minimum NO NO No
TDLBFD-00201803
required RX level.
Indicates the
minimum RX level
of an inter-
frequency
neighboring cell,
it to become a
candidate for cell
reselection. It
determines the
LBFD-00201803 /
TDLBFD-00201803
triggering cell
reselection to inter-
frequency
the frequency. The
value of this
parameter is
contained in SIB5.
For details, see
3GPP TS 36.331.

cell within an
eNodeB.
EARFCN range:
5180 to 5289,
lowest frequency of
the DL operating
band: 746;
Band 14: DL
EARFCN range:
5280 to 5379,
lowest frequency of
the DL operating
band: 758;
Band 17: DL
EARFCN range:
5730 to 5849,
lowest frequency of
the DL operating
band: 734;
LBFD-00201803 /
Band 18: DL
TDLBFD-00201803
EARFCN range: YES YES No
LBFD-00201802 /
5850 to 5999,
TDLBFD-00201802
lowest frequency of
the DL operating
band: 860;
Band 19: DL
EARFCN range:
6000 to 6149,
lowest frequency of
the DL operating
band: 875;
Band 20: DL
EARFCN range:
6150 to 6449,
lowest frequency of
the DL operating
band: 791;
Band 21: DL
EARFCN range:
Indicates the
starting physical cell
LBFD-00201803 /
ID of the inter-
TDLBFD-00201803
frequency YES YES No
LBFD-00201802 /
TDLBFD-00201802
details, see 3GPP
TS 36.331.

of the inter- TDLBFD-00201803
NO NO No
blacklisted cell. TDLBFD-00201802
Indicates the
physical cell ID
LBFD-00201803 /
range of the inter-
TDLBFD-00201803
frequency NO NO No
LBFD-00201802 /
TDLBFD-00201802
details, see 3GPP
TS 36.331.

cell within an
eNodeB.

country code of the
E-UTRAN
neighboring cell.
The PLMN consists
of the MCC and the
MNC.
LBFD-00201802 /
TDLBFD-00201802
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.

network code of the
E-UTRAN
neighboring cell.
The PLMN consists
of the MCC and the
MNC.
LBFD-00201802 /
TDLBFD-00201802
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
Indicates the
eNodeB identity of
the inter-frequency
uniquely identifies
an eNodeB within a
PLMN. The 28-bit
E-UTRAN cell
identity is
comprised of the
cell identity and the LBFD-00201802 /
YES YES No
eNodeB identity TDLBFD-00201802
(represented by the
most significant 20
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
Indicates the local

identity of the inter-
frequency
cell within an
eNodeB. The 28-bit
E-UTRAN cell
identity is
comprised of the
cell identity
(represented by the YES YES No LBFD-00201802
least significant
eight bits) and the
eNodeB identity.
The cell global
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
Indicates the cell
individual offset for
the inter-frequency
neighboring cell,
which is used in
LOFD-001032 /
evaluation for
TDLOFD-001032
handovers. It
LOFD-002005 /
affects the
TDLOFD-002005
probability of
triggering inter-
TDLBFD-00201802
frequency
LBFD-00201804 /
measurement
TDLBFD-00201804
reports. A larger
LBFD-00201805
value of this
parameter indicates
For details, see
3GPP TS 36.331.

for the inter-
frequency
neighboring cell,
which is used in
evaluation for cell
reselections. A
LBFD-00201803 /
larger value of this NO NO No
TDLBFD-00201803
a lower probability
of cell reselections.
This parameter is
contained in SIB5.
For details, see
3GPP TS 36.331.
handovers of UEs TDLBFD-00201802
NO NO No
to the neighboring LOFD-002001 /
cell are prohibited. TDLOFD-002001
Indicates whether
to permit or prohibit
removal of the LOFD-002001 /
NO NO No
relationship by
ANR.
The parameter
values are divided
into three value
ranges, indicating
the blind-handover
priority, frequency-
based-handover
priority, and 0. In
the same value
range, a larger
value indicates a
higher priority. Blind
handover is a
process in which
the eNodeB
LOFD-001032 /
instructs a UE to
TDLOFD-001032
hand over to a
LBFD-00201802 /
specified
TDLBFD-00201802
neighboring cell
without
TDLBFD-00201803
measurements. The
LBFD-00201804 /
value 0 indicates
TDLBFD-00201804
that blind
LBFD-00201805
handovers and
frequency-priority-
based handovers
are not allowed.
Values 1 to 16 are
designated only for
blind handovers.
Values 17 to 32 are
designated for
frequency-priority-
based handovers,
including
frequency-priority-
based blind
handovers and
Indicates whether
LOFD-002001 /
TDLOFD-002001
discovered by the
ANR algorithm.
LBFD-00201802 /
Indicates the name TDLBFD-00201802
NO NO No
TDLOFD-002001
of the inter- TDLBFD-00201802
NO NO No
neighboring cell. TDLOFD-002001

country code of the
external E-UTRAN
cell.
The PLMN consists
of the MCC and the
LBFD-00201801 /
MNC.
TDLBFD-00201801
LBFD-00201802 /
of three digits.
TDLBFD-00201802
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
network code of the
external E-UTRAN
cell.
The PLMN consists
of the MCC and the
LBFD-00201801 /
MNC.
TDLBFD-00201801
LBFD-00201802 /
of three digits.
TDLBFD-00201802
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
Indicates the
eNodeB identity of
the external E-
UTRAN cell. It
uniquely identifies
an eNodeB within a
PLMN. The 28-bit
E-UTRAN cell
identity is
comprised of the LBFD-00201801 /
cell identity and the TDLBFD-00201801
YES YES No
eNodeB identity LBFD-00201802 /
(represented by the TDLBFD-00201802
most significant 20
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
Indicates the cell
identity of the
external E-UTRAN
cell. It uniquely
identifies a cell
within an eNodeB.
The 28-bit E-
UTRAN cell identity
is comprised of the
cell identity LBFD-00201801 /
(represented by the TDLBFD-00201801
YES YES No
least significant LBFD-00201802 /
eight bits) and the TDLBFD-00201802
eNodeB identity.
The cell global
E-UTRAN cell is
comprised of the E-
UTRAN cell identity
and the PLMN ID.
For details, see
3GPP TS 36.413.
EARFCN range:
5180 to 5289,
lowest frequency of
the DL operating
band: 746;
Band 14: DL
EARFCN range:
5280 to 5379,
lowest frequency of
the DL operating
band: 758;
Band 17: DL
EARFCN range:
5730 to 5849,
lowest frequency of
the DL operating
band: 734;
LBFD-00201801 /
Band 18: DL
TDLBFD-00201801
EARFCN range: NO YES No
LBFD-00201802 /
5850 to 5999,
TDLBFD-00201802
lowest frequency of
the DL operating
band: 860;
Band 19: DL
EARFCN range:
6000 to 6149,
lowest frequency of
the DL operating
band: 875;
Band 20: DL
EARFCN range:
6150 to 6449,
lowest frequency of
the DL operating
band: 791;
Band 21: DL
EARFCN range:
Indicates whether
to set the UL
EARFCN for the
external E-UTRAN
cell. If this
NOT_CFG, the UL TDLBFD-00201801
NO NO No
EARFCN is the DL LBFD-00201802 /
EARFCN plus TDLBFD-00201802
18000 in FDD
mode and is the
same as the DL
EARFCN in TDD
mode.
lowest frequency of
the UL operating
band: 699;
Band 13: UL
EARFCN range:
23170 to 23279,
lowest frequency of
the UL operating
band: 776;
Band 14: UL
EARFCN range:
23280 to 23379,
lowest frequency of
the UL operating
band: 788;
Band 17: UL
EARFCN range:
23730 to 23849,
LBFD-00201801
lowest frequency of NO NO No
LBFD-00201802
the UL operating
band: 704;
Band 18: UL
EARFCN range:
23850 to 23999,
lowest frequency of
the UL operating
band: 815;
Band 19: UL
EARFCN range:
24000 to 24149,
lowest frequency of
the UL operating
band: 830;
Band 20: UL
EARFCN range:
24150 to 24449,
lowest frequency of

physical cell ID of TDLBFD-00201801
the external E- LBFD-00201802 /
NO YES No
UTRAN cell. For TDLBFD-00201802
TS 36.331. TDLBFD-00201803
Indicates the
tracking area code
(TAC) of the
external E-UTRAN
cell. Two TAC
values 0x0000(0)
and
LBFD-00201801 /
0xFFFE(65534) are
TDLBFD-00201801
reserved according NO YES No
LBFD-00201802 /
to the protocol and
TDLBFD-00201802
will not be used in
future versions.
Therefore, do not
use 0 or 65534 as a
TAC value in TAC
planning or
configuration.
LBFD-00201801 /
Indicates the name
TDLBFD-00201801
of the external E- NO NO No
LBFD-00201802 /
UTRAN cell.
TDLBFD-00201802
Indicates the cell

identity of the local
LBFD-00201803 /
cell. It uniquely YES YES No
TDLBFD-00201803
identifies a cell
within an eNodeB.
Indicates the index
of the GERAN
carrier frequency
LBFD-00201803 /
group. It uniquely YES YES No
TDLBFD-00201803
identifies a GERAN
carrier frequency
group.

country code (MCC)
of the operator that
shares the
neighboring
GERAN carrier
frequency group.
A public land mobile
network (PLMN) ID
is comprised of an
MCC and a mobile LBFD-00201803 /
YES YES No
network code TDLBFD-00201803
(MNC).
The MCC consists
of three digits.
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.

network code
(MNC) of the
operator that
shares the
neighboring
GERAN carrier
frequency group.
network (PLMN) ID
is comprised of a
LBFD-00201803 /
mobile country YES YES No
TDLBFD-00201803
code (MCC) and an
MNC.
The MCC consists
of three digits.
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
Indicates whether
to configure the cell
of the operator that LBFD-00201803 /
NO NO No
shares the TDLBFD-00201803
neighboring
GERAN carrier
frequency group.
shares the
neighboring
GERAN carrier
frequency group. If
the related SPID
configuration is
specified, set this
priority to the one
specified in the
SPID configuration.
If no related SPID
configuration is
specified but this
parameter is set,
the eNodeB
delivers the cell
reselection priorities
LBFD-00201803 /
of all PLMNs NO NO No
TDLBFD-00201803
supported by a UE
by using the IE
idleModeMobilityCo
ntrolInfo in an RRC
Connection
Release message
to the UE. If no
related SPID
configuration is
specified and this
parameter is not
set, a UE uses the
cell reselection
priority of the
neighboring
GERAN carrier
frequency group,
which is broadcast
cell within an
eNodeB.
country code of the
neighboring UTRAN
cell.
The PLMN consists
of the MCC and the
MNC.
LOFD-001019 /
TDLOFD-001019
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.

network code of the
neighboring UTRAN
cell.
The PLMN consists
of the MCC and the
MNC.
LOFD-001019 /
TDLOFD-001019
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
Indicates the
UTRAN cell ID. It
cell within a
PLMN.The 28-bit ID
of the UTRAN cell
RNC ID (indicated
by RncId) and a 16-
bit RNC cell ID LOFD-001019 /
YES YES No
(indicated by TDLOFD-001019
RncCellId). The
formula for
the external UTRAN
cell is as follows:
External UTRAN
cell ID = RNC ID x
65536 + RNC cell
ID.
Indicates whether
to allow handover
LOFD-001019 /
of UEs to the
TDLOFD-001019
neighboring cell NO NO No
LOFD-002002 /
that is determined
LOFD-002002
by the neighboring
relation.
Indicates whether
NO NO No
ANR.
Indicates the
priority of the
neighboring cell
during blind
handovers. Blind
handover is a
process in which
the eNodeB
instructs a UE to
hand over to a
specified
LBFD-002018 /
neighboring cell. NO NO No
TDLBFD-002018
There are 32
The priority has a
with the value of
this parameter.
Note that the value
0 indicates that
blind handovers to
are not allowed.
Indicates whether
LOFD-002001 /
TDLOFD-002001
LOFD-002002 /
discovered by the
TDLOFD-002002
ANR algorithm.
Indicates the name
of the local cell.
Indicates the name

LOFD-001019 /
of the UTRAN NO NO No
TDLOFD-001019
neighboring cell.
Indicates the ID of
the eNodeB, which
LOFD-001052 /
uniquely identifies NO NO Yes
TDLOFD-001052
an eNodeB within a
PLMN.
Indicates the RNC
ID of the
neighboring UTRAN
cell. This RNC ID
LOFD-001052 /
must be the same NO NO Yes
TDLOFD-001052
as the 12 bits on
the left of the
corresponding
UTRAN cell ID.
updated time of the
system information
that the eNodeB LOFD-001052 /
NO NO Yes
receives from the TDLOFD-001052
neighboring UTRAN
cell through the
RIM procedure.
Indicates the time

of the latest RIM
LOFD-001052 /
request received by NO NO Yes
TDLOFD-001052
the neighboring
UTRAN cell.
Indicates the cell

identity of the local
LBFD-00201803 /
cell. It uniquely YES YES No
TDLBFD-00201803
identifies a cell
within an eNodeB.
Normal UARFCNs:
[4357-4458]
Special UARFCNs:
(1007, 1012, 1032,
1037, 1062, 1087)
Band 6:
Normal UARFCNs:
[4387-4413]
Special UARFCNs:
(1037, 1062)
Band 7:
Normal UARFCNs:
[2237-2563]
Special UARFCNs:
(2587, 2612, 2637,
2662, 2687, 2712,
2737, 2762, 2787,
2812, 2837, 2862,
LBFD-00201803 /
2887, 2912) YES YES No
TDLBFD-00201803
Band 8:
Normal UARFCNs:
[2937-3088]
Special UARFCNs:
none
Band 9:
Normal UARFCNs:
[9237-9387]
Special UARFCNs:
none
The UARFCN
range in each TDD
frequency band is
shown as follows:
Band 1:
Normal UARFCNs:
[9500-9600] and
[10050-10125]

country code (MCC)
of the neighboring
UTRAN cell.
network (PLMN) ID
is comprised of an
MCC and a mobile
network code
LBFD-00201803 /
(MNC). YES YES No
TDLBFD-00201803
The MCC consists
of three digits.
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
network code
(MNC) of the
neighboring UTRAN
cell.
network (PLMN) ID
is comprised of a
mobile country
code (MCC) and an LBFD-00201803 /
YES YES No
MNC. TDLBFD-00201803
The MCC consists
of three digits.
The MNC consists
of two to three
digits.
For example, if the
MCC is 123 and the
MNC is 45, then the
PLMN ID is 12345.
Indicates whether
to configure the cell
LBFD-00201803 /
of the operator that NO NO No
TDLBFD-00201803
shares the
neighboring UTRAN
frequency.
Indicates the cell
shares the
neighboring UTRAN
frequency. If the
related SPID
configuration is
specified, set this
priority to the one
specified in the
SPID configuration.
If no related SPID
configuration is
specified but this
parameter is set,
the eNodeB
delivers the cell
reselection priorities LBFD-00201803 /
NO NO No
of all PLMNs TDLBFD-00201803
supported by a UE
by using the IE
idleModeMobilityCo
ntrolInfo in an RRC
Connection
Release message
to the UE. If no
related SPID
configuration is
specified and this
parameter is not
set, a UE uses the
cell reselection
priority of the
neighboring UTRAN
frequency, which is
broadcast in the
system information.
cell within an
eNodeB.
Normal UARFCNs:
[4357-4458]
Special UARFCNs:
(1007, 1012, 1032,
1037, 1062, 1087)
Band 6:
Normal UARFCNs:
[4387-4413]
Special UARFCNs:
(1037, 1062)
Band 7:
Normal UARFCNs:
[2237-2563]
Special UARFCNs:
(2587, 2612, 2637,
2662, 2687, 2712,
2737, 2762, 2787, LBFD-002009 /
2812, 2837, 2862, TDLBFD-002009
2887, 2912) LOFD-001019 /
YES YES No
Band 8: TDLOFD-001019
Normal UARFCNs: LOFD-002002 /
[2937-3088] TDLOFD-002002
Special UARFCNs:
none
Band 9:
Normal UARFCNs:
[9237-9387]
Special UARFCNs:
none
The UARFCN
range in each TDD
frequency band is
shown as follows:
Band 1:
Normal UARFCNs:
[9500-9600] and
[10050-10125]
Special UARFCNs:
Indicates the
LOFD-001019 /
working mode
TDLOFD-001019
LBFD-00201803 /
UTRAN in the
TDLBFD-00201803
current UARFCN.
Indicates the
LOFD-001019 /
TDD/FDD mode of
the inter-RAT
LOFD-002002
UTRAN.
follows if the DL
frequency is a
normal one:
Band 1: UL
UARFCN = DL
UARFCN - 950;
Band 2: UL
UARFCN = DL
UARFCN - 400;
Band 3: UL
UARFCN = DL
UARFCN - 475;
Band 4: UL
UARFCN = DL
UARFCN - 2000;
Band 5: UL
UARFCN = DL
LOFD-001019 /
UARFCN - 225;
TDLOFD-001019
Band 6: UL NO NO No
LBFD-00201803 /
UARFCN = DL
TDLBFD-00201803
UARFCN - 225;
Band 7: UL
UARFCN = DL
UARFCN - 600;
Band 8: UL
UARFCN = DL
UARFCN - 225;
Band 9: UL
UARFCN = DL
UARFCN - 475;
The default UL
UARFCN is
calculated as
follows if the DL
frequency is a
special one:
Band 2: UL
Normal UARFCNs:
[4132-4233]
Special UARFCNs:
(782, 787, 807,
812, 837, 862)
Band 6:
Normal UARFCNs:
[4162-4188]
Special UARFCNs:
(812, 837)
Band 7:
Normal UARFCNs:
[2012-2338]
Special UARFCNs:
(2362, 2387, 2412,
2437, 2462, 2487,
2512, 2537, 2562, LBFD-002009 /
2587, 2612, 2637, TDLBFD-002009
2662, 2687) LOFD-001019 /
NO NO No
[2712-2863] TDLOFD-002002
Special UARFCNs:
none
Band 9:
Normal UARFCNs:
[8762-8912]
Special UARFCNs:
none
The UARFCN
range in each TDD
frequency band is
shown as follows:
Band 1:
Normal UARFCNs:
[9500-9600] and
[10050-10125]
Special UARFCNs:
Indicates whether
to set the priority of
a cell assigned with LBFD-00201803 /
NO NO No
the UARFCN used TDLBFD-00201803
in cell reselection to
UTRAN.
parameter and the
the serving cell.
parameter is larger
than the absolute
priority of the
starts
measurements on
the UTRAN
frequency; then if
some neighboring
cells meets the
related conditions,
the UE starts cell LBFD-00201803 /
reselection. TDLBFD-00201803
NO NO No
If the value of this LBFD-002009 /
parameter is TDLBFD-002009
smaller than the
UE starts the
measurements only
when the signal
quality of the
then if the signal
quality of some
neighboring cells
meets the related
conditions, the UE
starts cell
reselection.
Frequencies used
for different RATs
Indicates the
maximum power
that the UE can
apply to
transmission on the
UTRAN frequency. LBFD-00201803 /
NO NO No
It is used in criteria TDLBFD-00201803
S to calculate the
compensated
power. For details,
see 3GPP TS
25.104.
Indicates the
frequency offset of
the cell on the
UTRAN frequency.
LOFD-001019 /
It determines the
TDLOFD-001019
LOFD-002002 /
triggering
TDLOFD-002002
measurement
reports for event
B1. For details, see
3GPP TS 36.331.
Indicates the
minimum quality
cell on the UTRAN
frequency to
become a
candidate for
reselection. This
parameter is
applied only to
reselection to
LBFD-00201803 /
UTRAN FDD cells. NO NO No
TDLBFD-00201803
A neighboring cell
on the UTRAN
frequency can
become a
candidate for
reselection only
when the signal
quality of the cell is
better than the
value of this
parameter.
Indicates the RX
neighboring cell on
the UTRAN
frequency to
become a
candidate for
selection. It is
S and used in the
evaluation for cell
selection. During
the evaluation for
cell reselection, the
UE performs the
following
LBFD-00201803 /
calculation: Srxlev = NO NO No
TDLBFD-00201803
Measured RSRP
value of a
neighboring cell on
the frequency -
Value of this
parameter -
Compensated
a neighboring cell is
better than a
threshold for a time-
to-trigger,
reselection to the
details, see 3GPP
TS 25.304.
Indicates the
minimum RX level
required for a
neighboring cell on
the UTRAN
frequency to
become a
candidate for
reselection if the
priority of the
frequency is higher
than that of the
serving frequency.
After
NO NO No
the UTRAN
frequency, the UE
reselects to a
neighboring cell on
the frequency only
if the RX level of
the cell is higher
than the value
specified by this
parameter for a
details, see 3GPP
TS 36.331.
Indicates the
minimum RX level
required for a
neighboring cell on
the UTRAN
frequency to
become a
candidate for
reselection if the
priority of the
frequency is lower
than that of the
serving frequency.
After
measurements are
started for
LBFD-00201803 /
neighboring cells on NO NO No
TDLBFD-00201803
the UTRAN
frequency, the UE
reselects to a
neighboring cell on
the frequency only
if the RX level of
the serving cell is
lower than a
specified threshold
is higher than the
value specified by
details, see 3GPP
TS 36.331.
Indicates the
RSRQ-based
minimum RX level
required for a
neighboring cell on
the frequency to
become a
candidate for
reselection if the
RSRQ-based
priority of the
frequency is higher
than that of the
serving frequency.
After
LBFD-00201803 /
measurements are NO NO No
TDLBFD-00201803
started for
the UTRAN
frequency, the UE
reselects to a
neighboring cell on
the frequency only
if the RSRQ-based
RX level of the cell
is higher than the
value specified by
details, see 3GPP
TS 36.331.
Indicates the
RSRQ-based
minimum RX level
required for a
neighboring cell on
the frequency to
become a
candidate for
reselection if the
RSRQ-based
priority of the
frequency is lower
than that of the
serving frequency.
After
measurements are
started for LBFD-00201803 /
NO NO No
the frequency, the
UE reselects to a
cell on the
frequency only if
the RSRQ-based
RX level of the
serving cell is lower
than a specified
threshold and that
of the cell is higher
than the value
specified by this
parameter for a
details, see 3GPP
TS 36.331.
the priority for the
neighboring UTRAN
frequency to carry
PS services. It is
used in coverage-
based handovers.
When
UtranFreqLayerMea
sSwitch is turned
on: If there are both
high and low PS-
priority UTRAN
frequencies, the
high PS-priority
UTRAN frequencies
are preferentially
measured; if there
are only low PS-
priority UTRAN LOFD-001019 /
NO NO No
frequencies, these TDLOFD-001019
low PS-priority
UTRAN frequencies
are measured.
If
UtranFreqLayerBlin
dSwitch is turned
on, the target cell
for a blind
coverage-based
handover is
preferentially
selected from the
neighboring UTRAN
cells on high PS-
If all neighboring
UTRAN cells are on
low PS-priority
the priority for the
neighboring UTRAN
frequency to carry
CS services. It is
used in CSFB-
triggered
handovers.
When
UtranFreqLayerMea
sSwitch is turned
on: If there are both
high and low CS-
priority UTRAN
frequencies, the
high CS-priority
UTRAN frequencies
are preferentially
LOFD-001033 /
measured; if there
TDLOFD-001033
are only low CS- NO NO No
LOFD-001078 /
priority UTRAN
TDLBFD-001078
frequencies, these
low CS-priority
UTRAN frequencies
are measured.
If
UtranFreqLayerBlin
dSwitch is turned
on, the target cell
for a blind handover
is preferentially
selected from the
neighboring UTRAN
cells on high CS-
If all neighboring
UTRAN cells are on
low CS-priority

country code of the
external UTRAN
cell.
The PLMN consists
of the MCC and the
MNC.
LOFD-001019 /
TDLOFD-001019
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
network code of the
external UTRAN
cell.
The PLMN consists
of the MCC and the
MNC.
LOFD-001019 /
TDLOFD-001019
of three digits.
The MNC consists
of two to three
digits.
For example, MCC
= 123, MNC = 45,
PLMN = 12345.
Indicates the ID of
the external UTRAN
cell. It uniquely
identifies a UTRAN
cell within a
PLMN.The 28-bit ID
of the external
UTRAN cell
RNC ID (indicated
by RncId) and a 16- LOFD-001019 /
YES YES No
bit RNC cell ID TDLOFD-001019
(indicated by
RncCellId). The
formula for
the external UTRAN
cell is as follows:
External UTRAN
cell ID = RNC ID x
65536 + RNC cell
ID.

NO NO No
of the UTRAN cell. TDLOFD-001019
[4357-4458]
Special UARFCNs:
(1007, 1012, 1032,
1037, 1062, 1087)
Band 6:
Normal UARFCNs:
[4387-4413]
Special UARFCNs:
(1037, 1062)
Band 7:
Normal UARFCNs:
[2237-2563]
Special UARFCNs:
(2587, 2612, 2637,
2662, 2687, 2712,
2737, 2762, 2787, LOFD-001019 /
2812, 2837, 2862, TDLOFD-001019
2887, 2912) LOFD-001044 /
NO YES No
[2937-3088] TDLOFD-001043
Special UARFCNs: LOFD-001072 /
none TDLOFD-001072
Band 9:
Normal UARFCNs:
[9237-9387]
Special UARFCNs:
none
The UARFCN
range in each TDD
frequency band is
shown as follows:
Band 1:
Normal UARFCNs:
[9500-9600] and
[10050-10125]
Special UARFCNs:
none
follows if the DL
frequency is a
normal one:
Band 1: UL
UARFCN = DL
UARFCN - 950;
Band 2: UL
UARFCN = DL
UARFCN - 400;
Band 3: UL
UARFCN = DL
UARFCN - 475;
Band 4: UL
UARFCN = DL
UARFCN - 2000;
Band 5: UL
UARFCN = DL
UARFCN - 225;
Band 6: UL LOFD-001019 /
NO NO No
UARFCN = DL TDLOFD-001019
UARFCN - 225;
Band 7: UL
UARFCN = DL
UARFCN - 600;
Band 8: UL
UARFCN = DL
UARFCN - 225;
Band 9: UL
UARFCN = DL
UARFCN - 475;
The default UL
UARFCN is
calculated as
follows if the DL
frequency is a
special one:
Band 2: UL
UARFCN = DL
[4132-4233]
Special UARFCNs:
(782, 787, 807,
812, 837, 862)
Band 6:
Normal UARFCNs:
[4162-4188]
Special UARFCNs:
(812, 837)
Band 7:
Normal UARFCNs:
[2012-2338]
Special UARFCNs:
(2362, 2387, 2412,
2437, 2462, 2487,
2512, 2537, 2562,
2587, 2612, 2637,
2662, 2687)
Band 8: LOFD-001019 /
NO NO No
Normal UARFCNs: TDLOFD-001019
[2712-2863]
Special UARFCNs:
none
Band 9:
Normal UARFCNs:
[8762-8912]
Special UARFCNs:
none
The UARFCN
range in each TDD
frequency band is
shown as follows:
Band 1:
Normal UARFCNs:
[9500-9600] and
[10050-10125]
Special UARFCNs:
none
Indicates the RNC
ID of the external
UTRAN cell. The
most left 12 bits of LOFD-001019 /
NO YES No
external UTRAN TDLOFD-001019
cell ID must be set
to the RNC ID of
the external cell.
Indicates whether
to set the routing
area code (RAC) of
the external UTRAN
cell. This parameter
LOFD-001019 /
must be set to CFG NO NO No
TDLOFD-001019
if the external
UTRAN cell
supports packet
switched (PS)
services.
NO NO No
routing area code. TDLOFD-001019
LOFD-001019 /
Indicates the TDLOFD-001019
primary DL LOFD-001044 /
scrambles of the TDLOFD-001044
NO YES No
external UTRAN LOFD-001043 /
cell. For details, see TDLOFD-001043
3GPP TS 25.331. LOFD-001072 /
TDLOFD-001072
LOFD-001019 /
TDLOFD-001019
LOFD-001044 /
Indicates the LAC
TDLOFD-001044
of the external NO YES No
LOFD-001043 /
UTRAN cell.
TDLOFD-001043
LOFD-001072 /
TDLOFD-001072
Indicates the name
LOFD-001019 /
of the external NO NO No
TDLOFD-001019
UTRAN cell.
Indicates whether
the external UTRAN
cell supports single
radio voice call
continuity (SRVCC)
for both CS and PS LOFD-001019 /
NO NO No
services. If this TDLOFD-001019
parameter is set to
BOOLEAN_FALSE,
the cell supports
only SRVCC for CS
services.
Indicates the
threshold above
which a neighboring
cell is added to a
serving cell by ANR.
The threshold is the
percentage of the
number of
successful
handovers to the
total number of
handovers from the
serving cell to the LOFD-002001 /
NO NO No
neighboring cell. In TDLOFD-002001
this version, this
parameter is no
longer used
internally although it
supports setting
synchronization
between the M2000
and the eNodeB.
Avoid using this
be removed from
later versions.
relationship with a
cell by ANR based
on the handover
success rate. The
threshold is the
percentage of the
number of
successful
handovers to the
total number of
handovers from the
local cell to the
neighboring cell.
For example, an
external cell is
configured as a
neighboring cell for
all cells under an
LOFD-002001 /
eNodeB, and this NO NO No
TDLOFD-002001
neighboring cell
permits automatic
removal of the
neighboring
relationship by
ANR. If the success
rate of handovers
from each cell
under the eNodeB
to this neighboring
cell is lower than or
equal to this
threshold after a
measurement
period, the
corresponding
external cell and
the neighbor
Indicates the
threshold for the
total number of
handovers to an
intra-RAT
neighboring cell,
LOFD-002001 /
above which ANR NO NO No
TDLOFD-002001
begins to evaluate
the removal of the
neighboring relation
in the case of a low
handover success
rate.
during which the
total number of
handovers to an
intra-RAT
neighboring cell is
LOFD-002001 /
measured by ANR NO NO No
TDLOFD-002001
to evaluate the
removal of the
in the case of a low
handover success
rate.
Indicates the
LOFD-002001 /
number of periodic
TDLOFD-002001
measurement NO NO No
LOFD-002002 /
reports sent for fast
TDLOFD-002002
ANR.
Indicates the
interval at which LOFD-002001 /
periodic TDLOFD-002001
NO NO No
measurement LOFD-002002 /
reports are sent for TDLOFD-002002
fast ANR.
Indicates the fast

ANR checking
timer. When the LOFD-002001 /
timer is expired, the TDLOFD-002001
NO NO No
eNodeB LOFD-002002 /
automatically TDLOFD-002002
checks whether to
disable fast ANR.
Indicates the
reference signal
received power
(RSRP) threshold
for intra-RAT fast
ANR. If the signal
quality in a LOFD-002001 /
neighboring E- TDLOFD-002001
NO NO No
UTRAN cell LOFD-002002 /
reported by the UE TDLOFD-002002
is lower than the
threshold, the cell is
not automatically
added as an
external cell of the
eNodeB.
Indicates the
maximum allowed
number of UEs that
perform intra-RAT
measurements for
fast ANR. After the
number of UEs
performing intra-
LOFD-002001 /
RAT measurements NO NO No
TDLOFD-002001
for fast ANR
reaches the
maximum number,
intra-RAT
measurements for
fast ANR will not be
performed on other
UEs.
Indicates the
maximum allowed
number of UEs that
perform inter-RAT
measurements for
fast ANR. After the
number of UEs
performing inter-
LOFD-002002 /
RAT measurements NO NO No
TDLOFD-002002
for fast ANR
reaches the
maximum number,
inter-RAT
measurements for
fast ANR will not be
performed on other
UEs.
Indicates the
threshold above
which the eNodeB
enters the
monitoring state for
intra-RAT fast ANR. LOFD-002001 /
NO NO No
The threshold is TDLOFD-002001
expressed as the
number of UEs that
have performed
measurements for
intra-RAT fast ANR.
Indicates the
threshold above
which the eNodeB
enters the
monitoring state for
inter-RAT fast ANR. LOFD-002002 /
NO NO No
The threshold is TDLOFD-002002
expressed as the
number of UEs that
have performed
measurements for
inter-RAT fast ANR.
Indicates the mode

for optimizing
neighboring
relations. If this
parameter is set to
FREE, neighboring
relations are
optimized
automatically by
ANR. If this LOFD-002001 /
NO NO No
CONTROLLED,
neighboring
relations to be
added or removed
are reported to the
M2000 and then
subject to manual
processing for
optimization.

during which the
number of
handovers are
measured for
removal from a
neighbor relation
table (NRT). In a
measurement
period for LOFD-002001 /
neighboring relation TDLOFD-002001
NO NO No
removal, when the LOFD-002002 /
total number of TDLOFD-002002
handovers from a
cell exceeds the
threshold for
removal, the
neighboring cells
that are not
detected by UEs
are removed from
the NRT.
Indicates the
number of
handovers above
which neighboring
relations are to be
removed from a
neighbor relation
table (NRT). In a
measurement
period for LOFD-002001 /
neighboring relation TDLOFD-002001
NO NO No
removal, when the LOFD-002002 /
total number of TDLOFD-002002
handovers from a
cell exceeds the
value of this
parameter, the
neighboring cells
that are not
detected by UEs
are removed from
the NRT.

used to enable or
disable proactive
PCI conflict
detection. Within a
specified duration
after this switch is
turned on, the
eNodeB delivers
measurement
configurations for LOFD-002001 /
NO NO No
proactive PCI TDLOFD-002001
conflict detection to
UEs that meet
specific
requirements. Then,
the eNodeB starts
the detection based
on the
measurement
reports from the
UEs.
Indicates the start

time of the active
PCI conflict
detection. If the
NO NO No
the start time, the
stop time is
assumed to be the
Indicates the stop
time of the active
PCI conflict
detection. If the
NO NO No
the start time, the
stop time is
assumed to be the
Indicates the
received signal
code power (RSCP)
threshold for fast
ANR with UTRAN.
If the signal quality
in a neighboring LOFD-002001 /
UTRAN cell NO NO No TDLOFD-002001
reported by the UE LOFD-002002
is lower than the
not automatically
added as an
eNodeB.
Indicates the
received signal
strength indicator
(RSSI) threshold for
fast ANR with
GERAN. If the
signal quality in a LOFD-002001 /
NO NO No
GERAN cell LOFD-002002 /
reported by the UE TDLOFD-002002
is lower than the
not automatically
added as an
eNodeB.
Indicates the pilot

strength threshold
for fast ANR with
CDMA2000 1xRTT.
CDMA2000 1xRTT TDLOFD-002001
NO NO No
cell reported by the LOFD-002002 /
UE is lower than TDLOFD-002002
the threshold, the
cell is not
automatically added
as an external cell
of the eNodeB.
Indicates the pilot
strength threshold
for fast ANR with
CDMA2000 HRPD.
CDMA2000 HRPD TDLOFD-002001
NO NO No
cell reported by the LOFD-002002 /
UE is lower than TDLOFD-002002
the threshold, the
cell is not
automatically added
as an external cell
of the eNodeB.

for the algorithm for
periodically
updating cell IDs. If
this parameter is
set to
BOOLEAN_TRUE,
cell IDs are
periodically LBFD-002009 /
NO NO No
updated, inserted TDLBFD-002009
into the system
information, and
broadcast to the
associated UEs
once the time at
which the algorithm
begins to take
effect is reached.
Indicates the time

at which the
algorithm for
periodically
updating cell IDs
begins to take
effect. If the switch
for the algorithm is
turned on, cell IDs
LBFD-002009 /
are periodically NO NO No
TDLBFD-002009
updated, inserted
into the system
information, and
broadcast to the
associated UEs
once the time
specified by this
parameter is
reached.
Indicates the period LBFD-002009 /

NO NO No
of updating cell IDs. TDLBFD-002009
Indicates the ID of
the eNodeB, which
uniquely identifies YES YES No None
an eNodeB within a
PLMN.
Indicates reserved
32-bit switch
parameter 0 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 1 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
32-bit switch
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
NO NO No None
patch versions and
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 2 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 3 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 4 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 5 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 6 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 7 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 8 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
parameter 9 that is
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
Indicates reserved
reserved for future
requirements.
Note on parameter
replacement:
Reserved
parameters are
temporarily used in
new parameters.
For example, the ID
of a new parameter
can signify the
parameter function.
Therefore, avoid
using this
parameter.
LBFD-00201801 /
collective switch LBFD-00201802 /
used to enable or TDLBFD-00201802
disable handover. LOFD-001043 /
Flash CS fallback to TDLOFD-001043
UTRAN: If the LOFD-001046 /
switch for CS TDLOFD-001046
fallback to UTRAN LBFD-00201805 /
is turned off, this TDLBFD-00201805
NO NO No
switch does not LOFD-001033 /
take effect; TDLOFD-001033
Flash CS fallback to LOFD-001034 /
GERAN: If the TDLOFD-001034
switch for CS LOFD-001035 /
fallback to GERAN TDLOFD-001035
is turned off, this LOFD-001052 /
switch does not TDLOFD-001052
take effect. LOFD-001053 /
TDLOFD-001053
Indicates the
switches
corresponding to
the inputs based on
which the eNodeB
determines
LOFD-001019 /
handover policies.
TDLOFD-001019
Note that
LOFD-001020 /
EutranVoipCapSwit
TDLOFD-001020
ch will be removed
LOFD-001021 /
in the later NO NO No
TDLOFD-001021
versions. In this
LOFD-001022 /
TDLOFD-001022
LOFD-001023 /
synchronized
TDLOFD-001023
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this switch.
Indicates the DL
ICIC algorithm
switch. There are
four states.
DlIcicSwitch_OFF_
ENUM:Indicates
that DL ICIC is
disabled.
DlIcicDynamicSwitc
h_ON_ENUM:Indic
ates that dynamic
DL ICIC is enabled.
DlIcicStaticSwitch_
ON_ENUM:Indicate LBFD-00202201 /
s that static DL ICIC TDLBFD-00202201
NO NO No
is enabled. LOFD-00101401 /
DlIcicReuse3Switch TDLOFD-00101401
_ON_ENUM: This
state will be
versions. In this
of this state is still
synchronized
between the M2000
and the eNodeB,
but it is no longer
used internally.
Therefore, avoid
using this state.
measured in
handovers, you are
advised to turn on
UtranEventAnrSwitc
h as well.
GeranFastAnrSwitc
h: If this switch is
turned on, fast ANR
with GERAN is
enabled to
construct and
optimize inter-RAT
neighboring
relations with
GERAN cells by
performing periodic
inter-RAT
measurements on LOFD-002001 /
GERAN. TDLOFD-002001
NO NO No
CdmaFastAnrSwitc LOFD-002002 /
h: If this switch is TDLOFD-002002
turned on, fast ANR
with CDMA2000 is
enabled to
construct and
optimize inter-RAT
neighboring
relations with
CDMA2000 cells by
performing periodic
intra-RAT
measurements on
CDMA2000
networks.
UtranAutoNrtDelete
Switch: If both
UtranEventAnrSwitc
h and this switch
used to enable or
disable the
redirection
algorithm. This
switch does not
control redirection
for CS fallback or
flash CS fallback.
GeranFlashRedirect
Switch: If both this
LOFD-001019 /
switch and the
TDLOFD-001019
switch for
LOFD-001020 /
redirection to NO NO No
TDLOFD-001020
GERAN are turned
LBFD-00201803 /
on, fast redirection
TDLBFD-00201803
to GERAN is
enabled.
UranFlashRedirect
Switch: If both this
switch and the
switch for
redirection to
UTRAN are turned
on, fast redirection
to UTRAN is
enabled.
: If this switch is
turned on, the
eNodeB can
dynamically adjust
the intra-frequency
handover
parameters to
increase the intra-
frequency handover
success rate; if the
the adjustment is
not performed.
InterFreqMroSwitch
: If this switch is
turned on, the
eNodeB can
dynamically adjust
LOFD-002005 /
the inter-frequency NO NO No
TDLOFD-002005
handover
parameters to
increase the inter-
frequency handover
success rate; if the
the adjustment is
not performed.
UtranMroSwitch: If
on, the eNodeB can
dynamically adjust
the UTRAN
handover
parameters to
increase the
success rate of
handovers to
for the TCP proxy
enhancer (TPE)
algorithm. The TPE
algorithm increases
the rates of TCP
services by
measures such as
ACK copying, ACK
splitting, and local
ACK
retransmission. LBFD-001001 /
If this switch is TDLBFD-001001
NO NO No
turned on, the TPE LOFD-001026 /
algorithm is TDLOFD-001028
enabled. In this
situation, the
algorithm is valid
only for UEs that
newly access or
reaccess the
network.
If this switch is
turned off, the TPE
algorithm is
disabled.
This parameter will
be removed in the
later versions. In
this version, the
setting of this
parameter is still LBFD-00202202 /
synchronized TDLBFD-00202202
NO NO No
between the M2000 LOFD-00101402 /
and the eNodeB, TDLOFD-00101402
but it is no longer
used internally.
Therefore, avoid
using this
parameter.
used to enable or
disable UL ICIC in
the frequency
domain. If this
UL ICIC in the
frequency domain
is disabled in the
eNodeB cells. If this LBFD-00202202 /
switch is set to TDLBFD-00202202
NO NO No
STATIC, static UL LOFD-00101402 /
ICIC in the TDLOFD-00101402
frequency domain
is enabled in the
eNodeB cells. If this
switch is set to
DYNAMIC, dynamic
UL ICIC in the
frequency domain
is enabled in the
eNodeB cells.
Indicates the
location services
(LCS) switch.
OtdoaSwitch: If the
observed time
difference of arrival- LOFD-001047 /
NO NO No
based (OTDOA- TDLOFD-001047
based) positioning
is enabled. If the
OTDOA-based
positioning is
disabled.
to UL data from
UEs in the case of
UL congestion. In
this case, UL
congestion may
occur in an
eNodeB, but
fairness and
differentiation for
combined services
are ensured.
A UE is considered
to have combined
services if the UE
has two or more
flow-controllable
non-GBR bearers.
Fairness and
LOFD-003011 /
differentiation for NO NO No
TDLOFD-003011
combined services
are ensured if the
UL scheduling
algorithm allocates
bandwidths to these
flow-controllable
non-GBR bearers
based on weighting
factors
(UlschPriorityFactor
) for UL scheduling
priorities. If the
the scheduling
algorithm is
instructed to limit
the number of
resource blocks

for reporting PCI
conflict alarms. If
the switch is turned
on, the PCI conflict
alarm is displayed
on the local
maintenance
terminal (LMT)
when a PCI LOFD-002007 /
NO NO No
collision among TDLOFD-002007
external cells or a
confusion among
neighboring cell
occurs. If the switch
is turned off, the
PCI conflict alarm is
not displayed when
such a PCI conflict
actually occurs.
used to enable or
disable the
eNodeB-level
energy
conservation
function. This
function is achieved
through the symbol-
based power
amplifier (PA)
shutdown. Symbol-
based PA shutdown
is applicable in
single-mode
LOFD-001070 /
eNodeBs. If this NO NO No
TDLOFD-001070
function is enabled,
the eNodeB shuts
down power
amplifiers (PAs) on
the corresponding
RF unit when it
detects no signal
transmitted on
OFDM symbols in
DL subframes. This
reduces static
power consumption
and hence
conserves energy
for the eNodeB.
UTRAN cells.
If this switch is
turned on, the
eNodeB can send
RAN-
INFORMATION-
REQUEST protocol
data units (PDUs)
to UTRAN cells to
request multiple
event-driven
reports.
If this switch is
turned off, the
eNodeB cannot
send RAN-
INFORMATION-
LOFD-001052 /
REQUEST PDUs to
TDLOFD-001052
UTRAN cells to NO NO No
LOFD-001053 /
request multiple
TDLOFD-001053
event-driven
reports.
GERAN_RIM_SWI
TCH: Indicates the
switch used to
enable or disable
the RIM procedure
that requests event-
driven multiple
reports from
GERAN cells.
If this switch is
turned on, the
eNodeB can send
RAN-
INFORMATION-
REQUEST PDUs to
PLMN lists in a
round robin (RR)
manner. In this
situation, if
IntraRatEventAnrS
witch or
IntraRatFastAnrSwit
ch is turned on for
the local eNodeB,
the local eNodeB
will ask the M2000
for the actual cell
global identifier
(CGI) and PLMN list
for a cell
broadcasting PLMN
IDs in an RR
manner after the LOFD-002001 /
UE reports the CGI TDLOFD-002001
NO NO No
of the cell during LOFD-002002 /
ANR TDLOFD-002002
measurements.
NBSLTERANSharin
gSwitch: If this
some neighboring
eNodeBs provide
cells that work in
RAN sharing mode.
In this situation, if
IntraRatEventAnrS
witch or
IntraRatFastAnrSwit
ch is turned on for
the local eNodeB,
the local eNodeB
will ask the M2000
for the PLMN list for
used to enable or
disable the UTRAN
hierarchy-based
measurement
algorithm and the
UTRAN hierarchy-
based blind-
handover
algorithm.If
UtranFreqLayerMea
sSwitch is turned
on, the UTRAN
hierarchy-based
measurement
algorithm takes
effect for
LOFD-001078 /
measurements NO NO No
TDLOFD-001078
related to coverage-
based and CSFB-
triggered handovers
from the E-UTRAN
to the UTRAN.
If
UtranFreqLayerBlin
dSwitch is turned
on, the UTRAN
hierarchy-based
blind-handover
algorithm takes
effect for coverage-
based and CSFB-
triggered handovers
from the E-UTRAN
to the UTRAN.
Indicates the
interval for
detecting license
alarms. During this
interval, the
eNodeB detects
NO NO No None
license control
items and reports
license alarms if the
condition for
generating license
alarms is met.
Indicates the
threshold for
generating license
alarms. A license
alarm is generated
if the proportion of
NO NO No None
the actually used
value to the
allocated value of
the license control
item exceeds this
threshold.
Indicates the
interval for clearing
license alarms.
During this interval,
the eNodeB detects
license control NO NO No None
items and clears
license alarms if the
condition for
clearing license
alarms is met.
Indicates the
threshold for
clearing license
alarms. A license
alarm is cleared if
the proportion of
NO NO No None
the actually used
value to the
allocated value of
the license control
item is below this
threshold.
Indicates the
proportion of the UL
licensed traffic to
the total licensed
traffic of the
eNodeB. The total
licensed traffic is LOFD-001036 /
NO NO No
the sum of UL and TDLOFD-001036
DL licensed traffic.
set to 100, there is
no DL licensed
traffic, affecting
service admission.
Indicates the mode
of traffic sharing
between the
operators in eRAN
sharing scenarios.
set to SHARING, all
the operators share
the total traffic of
the eNodeB without
proportional limits. If
LOFD-001036 /
this parameter is NO NO No
TDLOFD-001036
set to DEDICATE,
all the operators
share the total
traffic of the
eNodeB based on
specific proportions.
However, the
vacant traffic of an
operator can be
used by other
operators.
Indicates the
proportion of the
traffic used by the
operator with index
zero to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
all operators share NO NO No
TDLOFD-001036
traffic based on
specific proportions
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
traffic used by the
operator with index
one to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
traffic used by the
operator with index
two to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
traffic used by the
operator with index
three to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
traffic used by the
operator with index
four to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
traffic used by the
operator with index
five to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
traffic shared by the
operator with index
zero to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
operator with index
one to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
operator with index
two to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
operator with index
three to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
operator with index
four to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.
Indicates the
proportion of the
operator with index
five to the total
licensed traffic of
the eNodeB when
LOFD-001036 /
TDLOFD-001036
traffic based on
in eRAN sharing
scenarios and the
eNodeB does not
work in
independent mode.

of measurement for
MRO. During the
period, the number
of handovers is
measured and
abnormal scenarios
(including
premature LOFD-002005 /
NO NO No
handover, delayed TDLOFD-002005
handover, and ping-
pong handover) are
identified. After the
period elapses, the
eNodeB makes a
decision on
parameter
adjustment.
Indicates the
threshold for
enabling MRO
based on the
handover success
rate. MRO is
applied and
parameter LOFD-002005 /
NO NO No
adjustment is TDLOFD-002005
started only if the
success rate of
handovers from the
local cell to a
neighboring cell is
below this
threshold.
Indicates the
threshold of the
number of
handovers required
for enabling MRO.
MRO is applied and
parameter
LOFD-002005 /
adjustment is NO NO No
TDLOFD-002005
started only if the
number of
handovers from the
local cell to a
neighboring cell
reaches this
threshold.
Indicates the time

threshold for ping-
pong handover. If a
UE is handed over
back to the source
cell after staying in
the target cell for a
LOFD-002005 /
period shorter than NO NO No
TDLOFD-002005
this threshold, the
eNodeB decides
that a ping-pong
handover occurs
based on the
history information
about this UE.
Indicates the
threshold for the
percentage of intra-
RAT ping-pong
handovers. If the
percentage of intra-
RAT ping-pong
handovers exceeds
the threshold,
parameter LOFD-002005 /
NO NO No
adjustment is TDLOFD-002005
performed to
reduce the number
of ping-pong
handovers. If the
percentage is lower
than the threshold,
parameter
adjustment is not
performed.
Indicates the
threshold for
identifying
abnormal coverage
of the serving cell.
Weak coverage or
no coverage in the
overlapping area
between cells leads
to radio link failures
or handover
failures. Within a LOFD-002005 /
NO NO No
period, if the
number of such
failures between
the serving cell and
a neighboring cell
exceeds this
threshold, the
eNodeB does not
tune MRO-related
parameters of the
neighboring cell.
for a serving cell.
The threshold is
used to identify
abnormal coverage
in a serving cell.
When a UE
successfully
reaccesses a
network after a
radio link failure
(RLF) or handover
failure, the UE
submits an RLF
report. In the report,
if the RSRP value
less than the RSRP
threshold for the
LOFD-002005 /
serving cell and the NO NO No
TDLOFD-002005
RSRP value of a
neighboring cell is
less than the RSRP
threshold for
neighboring cells,
abnormal coverage
exists in the
overlapping area
between the
serving cell and this
the RSRP values of
neighboring cells
are not shown in
the RLF report,
abnormal coverage
definitely exists in
the serving cell.
for neighboring
cells, which is used
to identify abnormal
coverage between
a serving cell and
its neighboring
cells. When a UE
successfully
reaccesses a
network after a
radio link failure
(RLF) or handover
failure, the UE
submits an RLF
report. In the report,
if the RSRP value
less than the RSRP
threshold for the LOFD-002005 /
NO NO No
serving cell and the TDLOFD-002005
RSRP value of a
neighboring cell is
less than the RSRP
threshold for
neighboring cells,
abnormal coverage
exists in the
overlapping area
between the
serving cell and this
the RSRP values of
neighboring cells
are not shown in
the RLF report,
abnormal coverage
definitely exists in
the serving cell.
Indicates the index
of a simulated load
configuration. One
BS can store 10
YES YES No None
simulated load
configurations,
which are identified
by the indexes.
Indicates the RB
usage threshold of
a simulated load
configuration. If the
RB usage of a cell
NO NO No None
is below this
threshold, the
simulated load
scheduling is
performed.
Indicates the power
usage threshold of
a simulated load
power usage of a
NO NO No None
cell is below this
threshold, the
simulated load
scheduling is
performed.
Indicates the
reporting period for
simulated load. The
NO NO No None
value 0 indicates
that simulated load
is not reported.
Indicates the
measurement
period for simulated
load. The value 0 NO NO No None
indicates that
simulated load is
not measured.
that is used to
control whether to
enable and disable
the frequency-
selective
scheduling in
simulated load
NO NO No None
the frequency-
selective
scheduling is
enabled. If the
the frequency-
diversity scheduling
is used.
Indicates whether
to enable or disable LBFD-002008 /
NO NO No
the TCP ACK TDLBFD-002008
control algorithm.
Indicates the
maximum downlink
LBFD-002008 /
throughput for the NO NO No
TDLBFD-002008
TCP ACK control
algorithm.
Indicates the timer

length for the TCP
ACK control
algorithm. This
timer can be used
to control traffic of LBFD-002008 /
NO NO No
the ACKs to uplink TDLBFD-002008
TCP packets,
therefore
preventing traffic
bursts in the
downlink.
Indicates the time

delay of the frame
start time for all
TDD E-UTRAN
NO NO No None
cells under the
eNodeB to the time
of the reference
clock.
Indicates the
number of ports LOFD-001026 /
NO NO No
that enable TCP TDLOFD-001028
acceleration.
Indicates port 1 to
LOFD-001026 /
which TPE is to be NO NO No
TDLOFD-001028
applied.
Indicates port 2 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 3 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 4 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 5 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 6 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 7 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 8 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 9 to
LOFD-001026 /
TDLOFD-001028
applied.
Indicates port 10 to
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.
LOFD-001026 /
TDLOFD-001028
applied.

YES YES No
mapping identifier. TDLOFD-002004
Indicates the type
of the peer device,
which can be an S- LOFD-002004 /
NO YES No
GW or a TDLOFD-002004
neighboring
eNodeB.
Indicates whether
to use one
transmission
resource group for
all S-GWs or
neighboring
eNodeBs. If this
parameter is set to
YES, the eNodeB
uses one
transmission
LOFD-002004 /
resource group for NO YES No
TDLOFD-002004
all S-GWs or all
neighboring
eNodeBs. If this
parameter is set to
NO, the eNodeB
uses a unique
transmission
resource group for
each S-GW or each
neighboring
eNodeB.
Indicates the ID of
the peer device,
which can be an S-
GW or neighboring
eNodeB. If the peer
device is an S-GW,
this parameter must
be set to the S-GW LOFD-002004 /
NO NO No
ID. If the peer TDLOFD-002004
device is a
neighboring
eNodeB, this
parameter must be
set to the
neighboring
eNodeB ID.
Indicates the
cabinet number of
LOFD-002004 /
the target NO NO No
TDLOFD-002004
transmission
resource group.
Indicates the
subrack number of
LOFD-002004 /
the target NO NO No
TDLOFD-002004
transmission
resource group.
Indicates the slot

NO YES No
target transmission TDLOFD-002004
resource group.
Indicates the bear

type of the LOFD-002004 /
NO YES No
transmission TDLOFD-002004
resource group.
Indicates the ID of
the target LOFD-002004 /
NO YES No
resource group.
Indicates the type
of sub-board on the
board where a LOFD-002004 /
NO YES No
resource group is
established.
Indicates the
number of the port
where a LOFD-002004 /
NO NO No
resource group is
carried.
Indicates the type
of port where a
LOFD-002004 /
transmission NO YES No
TDLOFD-002004
resource group is
carried.
LOFD-002004 /
Indicates the name
TDLOFD-002004
of the SON security YES YES No
LOFD-003009 /
parameter group.
TDLOFD-003009
LOFD-002004 /
NO YES No
the IKE proposal. LOFD-003009 /
TDLOFD-003009
LOFD-002004 /
Indicates the name
TDLOFD-002004
of the IPSec NO YES No
LOFD-003009 /
proposal.
TDLOFD-003009

application type of TDLOFD-002004
NO NO No
the SON security LOFD-003009 /
parameter group. TDLOFD-003009
LOFD-002004 /
Indicates the IKE TDLOFD-002004
NO NO No
protocol version. LOFD-003009 /
TDLOFD-003009
Indicates the
exchange mode of
IKEv1. There are
two exchange
modes: main mode
and aggressive
mode. In main
mode, keys are
exchanged
separately from
identity information.
This protects
identity information
and hence
enhances security. LOFD-002004 /
The aggressive TDLOFD-002004
NO NO No
mode does not LOFD-003009 /
protect identity TDLOFD-003009
information, but is
useful in some
network
environments. If the
IKE proposal uses
the preshared key
(PSK)
authentication
method, the fully
qualified domain
name (FQDN) is
supported in main
mode but not in
aggressive mode.
Indicates the
LOFD-002004 /
preshared key. Both
TDLOFD-002004
ends must use the NO YES No
LOFD-003009 /
same preshared
TDLOFD-003009
key in negotiation.

to enable the dead TDLOFD-002004
NO NO No
peer detection LOFD-003009 /
(DPD) function. TDLOFD-003009
Indicates the dead
peer detection
(DPD) idle time. If
the local end does
not receive
encrypted packets
for a time defined
by this parameter, it
LOFD-002004 /
sends a DPD
TDLOFD-002004
message to perform NO NO No
LOFD-003009 /
dead peer
TDLOFD-003009
detection. However,
the exact time at
which the eNodeB
sends DPD
messages varies
depending on
network
environment.
Indicates the
interval at which the
eNodeB sends
DPD frames.
LOFD-002004 /
However, the exact
TDLOFD-002004
interval at which the NO NO No
LOFD-003009 /
eNodeB sends
TDLOFD-003009
DPD frames varies
depending on
network
environment.
Indicates the
maximum allowed
number of DPD LOFD-002004 /
frame TDLOFD-002004
NO NO No
retransmissions LOFD-003009 /
after a dead peer TDLOFD-003009
detection (DPD)
failure.
eNodeB to use a
key that is not
derived from the
first-phase key,
ensuring that the
two keys are
independent of
each other.
According to PFS,
each key protects a
unique set of data.
The elements used
to generate a key
are not reusable,
preventing the
disclosure of a key
from affecting
security of other LOFD-002004 /
keys. If the TDLOFD-002004
NO NO No
PFS_GROUP1 or TDLOFD-003009
PFS_GROUP2 at
the local eNodeB,
the peer device
must launch a PFS
exchange when
initiating IPSec
negotiation. During
this PFS exchange,
both ends must use
the same Diffie-
Hellman (DH) group
to calculate the key;
otherwise, the
negotiation fails.
Compared with the
768-bit DH group
(DH group 1), the
Indicates the
application mode of
the IPSec SA
lifetime. The value
GLOBAL indicates
that this lifetime
applies to all IPSec
LOFD-002004 /
SAs of the eNodeB,
TDLOFD-002004
while the value NO NO No
LOFD-003009 /
LOCAL indicates
TDLOFD-003009
that this lifetime
applies only to the
IPSec SAs
generated using the
IPSec proposal
specified in the
same MO.
Indicates the
lifetime of an IPSec
SA. An IPSec SA
becomes invalid if
its lifetime elapses.
Before an IPSec SA
becomes invalid,
IKE establishes a
new IPSec SA
through negotiation.
Before a new IPSec
SA is established,
the old IPSec SA is
still used to ensure LOFD-002004 /
communication TDLOFD-002004
NO NO No
security. Once the LOFD-003009 /
negotiation is TDLOFD-003009
complete, the new
IPSec SA is
immediately used.
IPSec SA
negotiation takes
some time. To
prevent SA updates
from affecting
communication
security, a lifetime
longer than 900
seconds is
recommended.
Indicates the
LOFD-002004 /
effective traffic of
TDLOFD-002004
the IPSec policy NO NO No
LOFD-003009 /
specified in the
TDLOFD-003009
same MO.
LOFD-002004 /
NO YES No
the operator. LOFD-003009 /
TDLOFD-003009
LBFD-003006 /
Indicates the ID of TDLBFD-003006
YES YES No
the IPv6 MME. LOFD-002004 /
TDLOFD-002004
Indicates the first
signaling IPv6
address of the IPv6
MME, which is to be LBFD-003006 /
used as the first TDLBFD-003006
NO YES No
peer IPv6 address LOFD-002004 /
for an automatically TDLOFD-002004
set up IPv6 SCTP
link on the S1
interface.
Indicates whether
to enable automatic
configuration of four
IPv6 IPSec MOs
(ACLRULE6, ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
LBFD-003006 /
(IKEPEER6,
TDLBFD-003006
IKEPROPOSAL,
LOFD-002004 /
and NO NO No
TDLOFD-002004
IPSECPROPOSAL)
LOFD-003024 /
to set up an IPv6
TDLOFD-003024
IPSec tunnel
between the
eNodeB and the
SeGW for the IPv6
MME to protect
data transmission
over the primary
path of the IPv6
SCTP link for the
S1 interface.
Indicates the name

of the IPv6 IKE LBFD-003006 /
peer that performs TDLBFD-003006
IPv6 IKE LOFD-002004 /
NO NO No
negotiation with the TDLOFD-002004
eNodeB when LOFD-003024 /
SIGIP1SECFLAG is TDLOFD-003024
set to ENABLE.
Indicates the name
of the IPSec
proposal used
when
LBFD-003006 /
SIGIP1SECFLAG is
TDLBFD-003006
set to ENABLE.
LOFD-002004 /
This IPv6 IPSec NO NO No
TDLOFD-002004
proposal is required
LOFD-003024 /
for IPv6 IPSec
TDLOFD-003024
negotiation
between the IPv6
MME and the
eNodeB.
Indicates the
second signaling
IPv6 address of the
IPv6 MME, which is LBFD-003006 /
to be used as the TDLBFD-003006
NO NO No
second peer IPv6 LOFD-002004 /
address for an TDLOFD-002004
automatically set up
IPv6 SCTP link on
the S1 interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE6, ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
LBFD-003006 /
(IKEPEER6,
TDLBFD-003006
IKEPROPOSAL,
LOFD-002004 /
and NO NO No
TDLOFD-002004
IPSECPROPOSAL)
LOFD-003024 /
to set up an IPv6
TDLOFD-003024
IPSec tunnel
between the
eNodeB and the
SeGW for the IPv6
MME to protect
data transmission
over the secondary
path of the IPv6
SCTP link for the
S1 interface.
Indicates the name

of the IPv6 IKE LBFD-003006 /
peer that performs TDLBFD-003006
NO NO No
negotiation with the TDLOFD-002004
eNodeB when LOFD-003024 /
SIGIP2SECFLAG is TDLOFD-003024
set to ENABLE.
Indicates the name

of the IPSec
proposal used
when
LBFD-003006 /
SIGIP2SECFLAG is
TDLBFD-003006
set to ENABLE.
LOFD-002004 /
This IPv6 IPSec NO NO No
TDLOFD-002004
proposal is required
LOFD-003024 /
for IPv6 IPSec
TDLOFD-003024
negotiation
between the IPv6
MME and the
eNodeB.
Indicates the local
port number of the
IPv6 MME, which is
LBFD-003006 /
to be used as the
TDLBFD-003006
peer port number NO YES No
LOFD-002004 /
for an automatically
TDLOFD-002004
set up IPv6 SCTP
link on the S1
interface.
LBFD-003006 /
Indicates the
TDLBFD-003006
description of the NO NO No
LOFD-002004 /
MME6.
TDLOFD-002004

the operator that TDLBFD-003006
NO NO No
owns the IPv6 LOFD-002004 /
MME. TDLOFD-002004
Indicates the
compliance protocol
release of the
MME. The value of
this parameter must
be the same as the
actual compliance
protocol release of
the MME. The
eNodeB sends S1
messages
LBFD-003006 /
complying with the
TDLBFD-003006
protocol release NO NO No
LOFD-002004 /
specified by this
TDLOFD-002004
parameter. If the
parameter value is
different from the
actual compliance
protocol release of
the MME, the way
in which the MME
handles these
message is subject
to the MME
implementation.
Indicates the MME LOFD-002004 /

YES YES No
ID. TDLOFD-002004
Indicates the first
signaling IP
address of the
MME, which is to be
LOFD-002004 /
used as the first NO YES No
TDLOFD-002004
peer IP address for
an automatically set
up SCTP link on the
S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
MOs (IKEPEER, LOFD-002004 /
IKEPROPOSAL, TDLOFD-002004
NO NO No
and LOFD-003009 /
IPSECPROPOSAL) TDLOFD-003009
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the MME
to protect data
transmission over
the primary path of
the SCTP link for
the S1 interface.
Indicates the name
of the SeGW
between which and
the eNodeB an
IPSec tunnel can
be automatically set LOFD-002004 /
up for the SCTP link TDLOFD-002004
NO NO No
using the first LOFD-003009 /
signaling IP TDLOFD-003009
address of the
MME. The SeGW
performs IKE
eNodeB.
Indicates the name
of the IPSec
proposal used
when
FIRSTIPSECFLAG LOFD-002004 /
is set to ENABLE. TDLOFD-002004
NO NO No
This IPSec LOFD-003009 /
proposal is required TDLOFD-003009
for IPSec
negotiation
between the MME
and the eNodeB.
Indicates the
second signaling IP
address of the
MME, which is to be
LOFD-002004 /
used as the second NO NO No
TDLOFD-002004
peer IP address for
up SCTP link on the
S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
NO NO No
and LOFD-003009 /
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the MME
to protect data
transmission over
the secondary path
of the SCTP link for
the S1 interface.
Indicates the name
of the SeGW
between which and
the eNodeB an
IPSec tunnel can
be automatically set LOFD-002004 /
up for the SCTP link TDLOFD-002004
NO NO No
using the second LOFD-003009 /
signaling IP TDLOFD-003009
address of the
MME. The SeGW
performs IKE
eNodeB.
Indicates the name
of the IPSec
proposal used
when
SECIPSECFLAG is LOFD-002004 /
set to ENABLE. TDLOFD-002004
NO NO No
This IPSec LOFD-003009 /
proposal is required TDLOFD-003009
for IPSec
negotiation
between the MME
and the eNodeB.
Indicates the local
port number of the
MME, which is to be
used as the peer LOFD-002004 /
NO YES No
port number for an TDLOFD-002004
SCTP link on the
S1 interface.
Indicates the
LOFD-002004 /
TDLOFD-002004
MME.
Indicates the ID of
LOFD-002004 /
the operator that NO NO No
TDLOFD-002004
owns the MME.
Indicates the
compliance protocol
release of the
MME. The value of
this parameter must
be the same as the
actual compliance
protocol release of
the MME. The
eNodeB sends S1
messages
complying with the
LOFD-002004 /
protocol release NO NO No
TDLOFD-002004
specified by this
parameter. If the
parameter value is
different from the
actual compliance
protocol release of
the MME, the way
in which the MME
handles these
message is subject
to the MME
implementation.
Indicates the
cabinet number of
LOFD-002004 /
the board where the NO NO No
TDLOFD-002004
S1 service IP
address is located.
Indicates the
subrack number of
LOFD-002004 /
TDLOFD-002004
S1 service IP
address is located.
Indicates the slot
number of the
LOFD-002004 /
board where the S1 NO YES No
TDLOFD-002004
service IP address
is located.
Indicates the ID of
LOFD-002004 /
the S1 service IP YES YES No
TDLOFD-002004
address.
Indicates the S1
service IP address
of the eNodeB,
which is to be used
LOFD-002004 /
as the local IP NO YES No
TDLOFD-002004
address for an
IP path on an S1
interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
LOFD-002004 /
MOs (IKEPEER,
TDLOFD-002004
IKEPROPOSAL, NO NO No
LOFD-003009 /
and
TDLOFD-003009
IPSECPROPOSAL)
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the SGW
to protect data
transmission over
the IP Paths for the
S1 interface.
Indicates the local
IP address used
when IPSECFLAG LOFD-002004 /
NO NO No
The eNodeB uses LOFD-003009 /
this IP address in TDLOFD-003009
IKE negotiation with
a peer device.
Indicates whether
to enable the PING
detection to check
the connectivity of
up IP path.If the
PING detection is
disabled in the
firewall located in
the transport
network or in the
CN equipment, a LOFD-002004 /
NO NO No
detection failure is TDLOFD-002004
resulted, which will
cause the re-
establishment of
the S1 interface
and disrupt services
in the cell.
Therefore, this
parameter must be
set to DISABLE
under such
scenarios.

NO NO No
the operator. TDLOFD-002004
LBFD-003006 /
Indicates the ID of
TDLBFD-003006
the S1 service IPv6 YES YES No
LOFD-002004 /
address.
TDLOFD-002004
Indicates the
LBFD-003006 /
cabinet number of
TDLBFD-003006
LOFD-002004 /
S1 service IP
TDLOFD-002004
address is located.
Indicates the
LBFD-003006 /
subrack number of
TDLBFD-003006
LOFD-002004 /
S1 service IPv6
TDLOFD-002004
address is located.
Indicates the slot
LBFD-003006 /
number of the
TDLBFD-003006
LOFD-002004 /
service IPv6
TDLOFD-002004
address is located.
Indicates the S1
service IPv6
address of the
LBFD-003006 /
eNodeB, which is to
TDLBFD-003006
be used as the local NO YES No
LOFD-002004 /
IPv6 address for an
TDLOFD-002004
IPv6 path on an S1
interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE,6 ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
LBFD-003006 /
IPv6 IPSec MOs
TDLBFD-003006
(IKEPEER6,
LOFD-002004 /
IKEPROPOSAL, NO NO No
TDLOFD-002004
and
LOFD-003024 /
IPSECPROPOSAL)
TDLOFD-003024
to set up an IPv6
IPSec tunnel
between the
eNodeB and the
SeGW for the IPv6
SGW to protect
data transmission
over the IPv6 Paths
for the S1 interface.
Indicates the local
IPv6 address used
when LBFD-003006 /
SERVIPSECFLAG TDLBFD-003006
is set to ENABLE. LOFD-002004 /
NO NO No
The eNodeB uses TDLOFD-002004
this IPv6 address in LOFD-003024 /
IPv6 IKE TDLOFD-003024
negotiation with a
peer device.
Indicates whether
to enable the PING
detection check the
connectivity of an
IPv6 path.If the
PING detection is
disabled in the
firewall located in
the transport
network or in the LBFD-003006 /
CN equipment, a TDLBFD-003006
NO NO No
detection failure is LOFD-002004 /
resulted, which will TDLOFD-002004
cause the re-
establishment of
the S1 interface
in the cell.
Therefore, this
parameter must be
set to DISABLE
under such
scenarios.
Indicates the ID of
LBFD-003006 /
the operator that
TDLBFD-003006
owns the S1 NO NO No
LOFD-002004 /
service IPv6
TDLOFD-002004
address.
Indicates the
cabinet number of
LOFD-002004 /
TDLOFD-002004
S1 signaling IP
address is located.
Indicates the
subrack number of
LOFD-002004 /
TDLOFD-002004
S1 signaling IP
address is located.
Indicates the slot
number of the
LOFD-002004 /
TDLOFD-002004
signaling IP
address is located.
Indicates the ID of
LOFD-002004 /
the S1 signaling IP YES YES No
TDLOFD-002004
address.
Indicates the first
S1 signaling IP
address of the
eNodeB, which is to
LOFD-002004 /
be used as the first NO YES No
TDLOFD-002004
local IP address for
up SCTP link on an
S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
NO NO No
and LOFD-003009 /
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the MME
to protect data
transmission over
the primary path of
the SCTP link for
the S1 interface.
Indicates the first
local IP address
used when
LOFD-002004 /
LOCIPSECFLAG is
TDLOFD-002004
set to ENABLE. The NO NO No
LOFD-003009 /
eNodeB uses this
TDLOFD-003009
IP address in IKE
negotiation with a
peer device.
Indicates the
second S1
signaling IP
address of the
eNodeB, which is to
LOFD-002004 /
be used as the NO NO No
TDLOFD-002004
second local IP
address for an
SCTP link on an S1
interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
NO NO No
and LOFD-003009 /
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the MME
to protect data
transmission over
the secondary path
of the SCTP link for
the S1 interface.
Indicates the
second local IP
address used when
SECLOCIPSECFLA LOFD-002004 /
G is set to TDLOFD-002004
NO NO No
ENABLE. The LOFD-003009 /
eNodeB uses this TDLOFD-003009
IP address in IKE
negotiation with a
peer device.
Indicates the SCTP

port number of the
eNodeB, which is to
be used as the local LOFD-002004 /
NO YES No
SCTP port number TDLOFD-002004
set up SCTP link on
an S1 interface.
Indicates the
minimum value of
the retransmission
timeout (RTO).
According to the
SCTP protocol, if
the calculated RTO
is less than this LOFD-002004 /
NO NO No
parameter value, TDLOFD-002004
the round trip delay
is set to this
parameter value to
reduce the
probability of
retransmission
timeout.
Indicates the
maximum value of
the retransmission
timeout (RTO).
According to the
LOFD-002004 /
SCTP protocol, it is NO NO No
TDLOFD-002004
the upper limit for
the doubling
operation of the
retransmission
timeout timer.
Indicates the initial

value of the
Retransmission
TimeOut (RTO). It is
used as the initial LOFD-002004 /
NO NO No
value when TDLOFD-002004
calculating the
retransmission
timeout in the SCTP
protocol.
For details about

the RtoAlpha
parameter, see
RFC4960. Indicates
the value of
RtoAlpha. It is used
as smooth factor of
the round-trip delay
LOFD-002004 /
calculation in the NO NO No
TDLOFD-002004
SCTP protocol. In a
new estimation,
(RtoAlpha/100) is
taken from a new
measurement, and
1-(RtoAlpha/100) is
taken from the last
estimation.
For details about
the RtoBeta
parameter, see
RFC4960. Indicates
the value of
RtoBeta. It is used
as smooth factor of
the round-trip delay
LOFD-002004 /
calculation in the NO NO No
TDLOFD-002004
SCTP protocol. In a
new estimation,
(RtoAlpha/100) is
taken from the
offset gain, and 1-
(RtoBeta/100) is
taken from the last
estimation.
Indicates the
heartbeat interval,
corresponding to
the HBINTER
parameter specified
in RFC4960. SCTP
periodically
transmits heartbeat
messages to an idle
destination address
to detect the LOFD-002004 /
NO NO No
reachability. TDLOFD-002004
According to
RFC4960, the
actual interval at
which heartbeat
messages are
transmitted equals
the parameter value
(HBINTER) plus the
retransmission
timeout (RTO).
Indicates the
maximum number
of retransmissions
on the SCTP link. If
the number of
retransmissions on
the SCTP link LOFD-002004 /
NO NO No
reaches this TDLOFD-002004
parameter value,
this SCTP link is
considered broken
and the eNodeB
reports a link failure
alarm.
Indicates the
maximum number
of retransmissions
over a path. When
the number of
retransmissions
over a path
exceeds the value
of this parameter, LOFD-002004 /
NO NO No
the path is regarded TDLOFD-002004
as failed if no
heartbeat
acknowledgment is
received. If multiple
paths are used,
path switching is
automatically
performed.
Indicates whether
to calculate the
checksum of each
message to be
transmitted. If this
parameter is set to
ENABLE, the
eNodeB calculates
LOFD-002004 /
the checksum. If NO NO No
TDLOFD-002004
the calculated
checksum is
different from that
contained in the
message, the local
eNodeB does not
transmit the
message.
Indicates whether
to calculate the
checksum of each
received message.
set to ENABLE, the
eNodeB calculates
LOFD-002004 /
the checksum. If NO NO No
TDLOFD-002004
the calculated
checksum is
different from that
contained in the
message, the local
eNodeB discards
the message.
Indicates the type

LOFD-002004 /
of the checksum NO NO No
TDLOFD-002004
calculation.
Indicates whether
to switch back to
the primary path
LOFD-002004 /
upon restoration of NO NO No
TDLOFD-002004
the automatically
set up SCTP link on
the S1 interface.
Indicates the
number of
consecutive
heartbeat
messages that
must be transmitted
on the primary path
LOFD-002004 /
before the eNodeB NO NO No
TDLOFD-002004
can switch back to
the primary path.
This parameter is
valid only when
SWITCHBACKFLA
G is set to
ENABLE.
Indicates the time

interval that one
end of SCPT link
has to wait before it
can send an SACK
message in
response to data
reception. A larger
LOFD-002004 /
TDLOFD-002004
parameter indicates
a longer time
interval between
the reception of
data and the
sending of the
corresponding
SACK message.
Indicates the ID of
the operator that
LOFD-002004 /
TDLOFD-002004
signaling IP
address.
LBFD-003006 /
Indicates the ID of
TDLBFD-003006
the S1 signaling YES YES No
LOFD-002004 /
IPv6 address.
TDLOFD-002004
Indicates the
LBFD-003006 /
cabinet number of
TDLBFD-003006
LOFD-002004 /
S1 signaling IPv6
TDLOFD-002004
address is located.
Indicates the slot
LBFD-003006 /
number of the
TDLBFD-003006
board where the S1 NO NO No
LOFD-002004 /
signaling IPv6
TDLOFD-002004
address is located.
Indicates the slot
LBFD-003006 /
number of the
TDLBFD-003006
LOFD-002004 /
signaling IPv6
TDLOFD-002004
address is located.
Indicates the first

S1 signaling IPv6
address of the
eNodeB, which is to LBFD-003006 /
be used as the first TDLBFD-003006
NO YES No
local IPv6 address LOFD-002004 /
set up IPv6 SCTP
link on an S1
interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE6, ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
LBFD-003006 /
(IKEPEER6,
TDLBFD-003006
IKEPROPOSAL,
LOFD-002004 /
and NO NO No
TDLOFD-002004
IPSECPROPOSAL)
LOFD-003024 /
to set up an IPv6
TDLOFD-003024
IPSec tunnel
between the
eNodeB and the
SeGW for the IPv6
MME to protect
data transmission
over the primary
path of the IPv6
SCTP link for the
S1 interface.
Indicates the first
local IPv6 address
used when LBFD-003006 /
SIGIP1SECFLAG is TDLBFD-003006
set to ENABLE. The LOFD-002004 /
NO NO No
IPv6 address in LOFD-003024 /
negotiation with a
peer device.
Indicates the
second S1
signaling IPv6
address of the
LBFD-003006 /
eNodeB, which is to
TDLBFD-003006
LOFD-002004 /
second local IPv6
TDLOFD-002004
address for an
IPv6 SCTP link on
an S1 interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE6, ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
LBFD-003006 /
(IKEPEER6,
TDLBFD-003006
IKEPROPOSAL,
LOFD-002004 /
and NO NO No
TDLOFD-002004
IPSECPROPOSAL)
LOFD-003024 /
to set up an IPv6
TDLOFD-003024
IPSec tunnel
between the
eNodeB and the
SeGW for the IPv6
MME to protect
data transmission
over the secondary
path of the IPv6
SCTP link for the
S1 interface.
Indicates the
second local IPv6
address used when LBFD-003006 /
NO NO No
IPv6 address in LOFD-003024 /
negotiation with a
peer device.
Indicates the SCTP

port number of the
eNodeB, which is to
LBFD-003006 /
be used as the local
TDLBFD-003006
SCTP port number NO YES No
LOFD-002004 /
TDLOFD-002004
set up IPv6 SCTP
link on an S1
interface.
Indicates the
minimum
retransmission
timeout (RTO)
value of an IPv6 LBFD-003006 /
SCTP link. The time TDLBFD-003006
NO NO No
that a link LOFD-002004 /
connectivity check TDLOFD-002004
takes has a positive
value of this
parameter.
Indicates the
maximum RTO
value of an IPv6
SCTP link. The time LBFD-003006 /
that a link TDLBFD-003006
NO NO No
connectivity check LOFD-002004 /
takes has a positive TDLOFD-002004
value of this
parameter.
RTO value of an
IPv6 SCTP link.
LBFD-003006 /
The time that a link
TDLBFD-003006
connectivity check NO NO No
LOFD-002004 /
TDLOFD-002004
value of this
parameter.
Indicates the Alpha

value for RTO for
an IPv6 SCTP link.
A larger value of
LBFD-003006 /
this parameter
TDLBFD-003006
indicates a lower NO NO No
LOFD-002004 /
sensitivity of the
TDLOFD-002004
IPv6 SCTP link to
the time delay. For
details, see
RFC4960.
Indicates the Beta
value for RTO for
an IPv6 SCTP link.
A larger value of
LBFD-003006 /
this parameter
TDLBFD-003006
LOFD-002004 /
sensitivity of the
TDLOFD-002004
IPv6 SCTP link to
the time delay. For
details, see
RFC4960.
Indicates the
heartbeat interval of
the IPv6 SCTP link.
The status of an
IPv6 SCTP link is
checked by each
end sending
heartbeat
messages to the
other end. If one
end receives one
heartbeat
acknowledgment,
then it considers LBFD-003006 /
the IPv6 SCTP link TDLBFD-003006
NO NO No
as connected. LOFD-002004 /
However, if one end TDLOFD-002004
has transmitted
heartbeat
messages for a
number greater
than the
MAXASSOCRETR
value but has not
received any
heartbeat
acknowledgments,
then it considers
the IPv6 SCTP link
as broken.
Indicates the
maximum number
of retransmissions
over an IPv6 SCTP
link. If this IPv6
SCTP link has
multiple paths, then
this IPv6 SCTP link
is also called an
IPv6 SCTP
association and this
parameter indicates
LBFD-003006 /
the maximum
TDLBFD-003006
number of NO NO No
LOFD-002004 /
retransmissions
TDLOFD-002004
over an IPv6 SCTP
association. When
the number of
retransmissions on
the association
exceeds the value
of this parameter,
the eNodeB
considers the IPv6
SCTP link as
broken and reports
a link failure alarm.
Indicates the
maximum number
of retransmissions
over a path. If the
number of
retransmissions
over a path
exceeds the value LBFD-003006 /
of this parameter TDLBFD-003006
NO NO No
but no response LOFD-002004 /
message is TDLOFD-002004
received, the
eNodeB considers
this path as
unreachable, and
switches to another
path if multihoming
is used.
Indicates whether
to calculate the
checksum of each
message to be
transmitted. If the
calculated
checksum of a LBFD-003006 /
message is different TDLBFD-003006
NO NO No
from the checksum LOFD-002004 /
contained in the TDLOFD-002004
message, the
eNodeB considers
this message to
have bit errors and
does not transmit
the message.

to check the TDLBFD-003006
NO NO No
checksum of each LOFD-002004 /
received message. TDLOFD-002004
checksum TDLBFD-003006
NO NO No
calculation LOFD-002004 /
algorithm. TDLOFD-002004
Indicates whether
to switch back to
the primary path
when the primary
path is restored.
When the primary
path is
LBFD-003006 /
unreachable, the
TDLBFD-003006
eNodeB switches to NO NO No
LOFD-002004 /
the secondary path.
TDLOFD-002004
This parameter is
used to set whether
the eNodeB
switches back to
the primary path
when the primary
path is restored.
Indicates the
number of
consecutive
heartbeat response
messages that
must be detected
over the primary
path of an IPv6
SCTP link before
the eNodeB can
LBFD-003006 /
switch back to this
TDLBFD-003006
primary path. After NO NO No
LOFD-002004 /
the primary path is
TDLOFD-002004
restored and the
number of
consecutive
heartbeat response
messages reaches
the value of this
parameter, the
eNodeB switches
back to the primary
path.
Indicates the ID of
LBFD-003006 /
the operator that
TDLBFD-003006
LOFD-002004 /
signaling IPv6
TDLOFD-002004
address.
Indicates the ID of
the service gateway
(S-GW). A
maximum of 128 S- LOFD-002004 /
YES YES No
GWs can establish TDLOFD-002004
S1 user plane
connections with
each eNodeB.
Indicates the first

service IP address
of the S-GW, which
LOFD-002004 /
is to be used in NO YES No
TDLOFD-002004
automatic setup of
an IP Path on the
S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
MOs (IKEPEER,
LOFD-002004 /
IKEPROPOSAL,
TDLOFD-002004
and NO NO No
LOFD-003009 /
IPSECPROPOSAL)
TDLOFD-003009
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the SGW
to protect data
transmission over
the IP Path set up
using the first
service IP address
Indicates the name

of the SeGW used
when
LOFD-002004 /
SERVIP1IPSECFL
TDLOFD-002004
AG is set to NO NO No
LOFD-003009 /
ENABLE. The
TDLOFD-003009
SeGW performs
the eNodeB.
Indicates the name

of the IPSec
proposal used
when
SERVIP1IPSECFL LOFD-002004 /
AG is set to TDLOFD-002004
NO NO No
ENABLE. This LOFD-003009 /
IPSec proposal is TDLOFD-003009
required for IPSec
negotiation
between the S-GW
and the eNodeB.
Indicates the
second service IP
address of the S-
LOFD-002004 /
GW, which is to be NO NO No
TDLOFD-002004
used in automatic
setup of an IP Path
on the S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
MOs (IKEPEER,
LOFD-002004 /
IKEPROPOSAL,
TDLOFD-002004
and NO NO No
LOFD-003009 /
IPSECPROPOSAL)
TDLOFD-003009
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the SGW
to protect data
transmission over
the IP Path set up
using the second
service IP address
Indicates the name

of the SeGW used
when
LOFD-002004 /
SERVIP2IPSECFL
TDLOFD-002004
LOFD-003009 /
ENABLE. The
TDLOFD-003009
SeGW performs
the eNodeB.
Indicates the name

of the IPSec
proposal used
when
NO NO No
required for IPSec
negotiation
between the S-GW
and the eNodeB.
Indicates the third
service IP address
of the S-GW, which
LOFD-002004 /
is to be used in NO NO No
TDLOFD-002004
automatic setup of
an IP Path on the
S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
MOs (IKEPEER,
LOFD-002004 /
IKEPROPOSAL,
TDLOFD-002004
and NO NO No
LOFD-003009 /
IPSECPROPOSAL)
TDLOFD-003009
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the SGW
to protect data
transmission over
the IP Path set up
using the third
service IP address
Indicates the name

of the SeGW used
when
LOFD-002004 /
SERVIP3IPSECFL
TDLOFD-002004
LOFD-003009 /
ENABLE. The
TDLOFD-003009
SeGW performs
the eNodeB.
Indicates the name

of the IPSec
proposal used
when
NO NO No
required for IPSec
negotiation
between the S-GW
and the eNodeB.
Indicates the fourth
service IP address
of the S-GW, which
LOFD-002004 /
is to be used in NO NO No
TDLOFD-002004
automatic setup of
an IP Path on the
S1 interface.
Indicates whether
to enable automatic
IPSec MOs
(ACLRULE, ACL,
IPSECPOLICY, and
IPSECBIND) based
on the other user-
configured IPSec
MOs (IKEPEER,
LOFD-002004 /
IKEPROPOSAL,
TDLOFD-002004
and NO NO No
LOFD-003009 /
IPSECPROPOSAL)
TDLOFD-003009
to set up an IPSec
tunnel between the
eNodeB and the
SeGW for the SGW
to protect data
transmission over
the IP Path set up
using the fourth
service IP address
Indicates the name

of the SeGW used
when
LOFD-002004 /
SERVIP4IPSECFL
TDLOFD-002004
LOFD-003009 /
ENABLE. The
TDLOFD-003009
SeGW performs
the eNodeB.
Indicates the name

of the IPSec
proposal used
when
NO NO No
required for IPSec
negotiation
between the S-GW
and the eNodeB.
Indicates the
LOFD-002004 /
TDLOFD-002004
SGW.
Indicates the ID of
LOFD-002004 /
the operator that NO NO No
TDLOFD-002004
owns the S-GW.
LBFD-003006 /
YES YES No
the IPv6 S-GW. LOFD-002004 /
TDLOFD-002004
Indicates the first

service IPv6
address of the IPv6 LBFD-003006 /
S-GW, which is to TDLBFD-003006
NO YES No
be used in LOFD-002004 /
automatic setup of TDLOFD-002004
an IP path on the
S1 interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE,6 ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
(IKEPEER6, LBFD-003006 /
IKEPROPOSAL, TDLBFD-003006
and LOFD-002004 /
NO NO No
to set up an IPv6 LOFD-003024 /
IPSec tunnel TDLOFD-003024
between the
eNodeB and the
SeGW for the IPv6
SGW to protect
data transmission
over the IPv6 Path
set up using the
first service IPv6
address for the S1
interface.
Indicates the name

of the security
gateway (SeGW) of
the serving gateway
LBFD-003006 /
(S-GW), which
TDLBFD-003006
performs IKE
LOFD-002004 /
negotiation with the NO NO No
TDLOFD-002004
local eNodeB. This
LOFD-003024 /
parameter is valid
TDLOFD-003024
only when
SERVIP1IPSECFL
AG is set to
ENABLE.
Indicates the name

of the IP security
(IPsec) proposal,
LBFD-003006 /
IPsec negotiation
TDLBFD-003006
between the S-GW
LOFD-002004 /
and the local NO NO No
TDLOFD-002004
eNodeB. This
LOFD-003024 /
parameter is valid
TDLOFD-003024
only when
SERVIP1IPSECFL
AG is set to
ENABLE.
Indicates the
second service
IPv6 address of the LBFD-003006 /
IPv6 S-GW, which TDLBFD-003006
NO NO No
is to be used in LOFD-002004 /
an IPv6 path on the
S1 interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE,6 ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
and LOFD-002004 /
NO NO No
between the
eNodeB and the
SeGW for the IPv6
SGW to protect
data transmission
over the IPv6 Path
set up using the
second service
IPv6 address for
the S1 interface.
Indicates the name

of the SeGW used
when LBFD-003006 /
SERVIP2IPSECFL TDLBFD-003006
AG is set to LOFD-002004 /
NO NO No
ENABLE. The TDLOFD-002004
SeGW performs LOFD-003024 /
eNodeB.
Indicates the name

of the IP security
(IPsec) proposal,
LBFD-003006 /
IPsec negotiation
TDLBFD-003006
between the S-GW
LOFD-002004 /
TDLOFD-002004
eNodeB. This
LOFD-003024 /
parameter is valid
TDLOFD-003024
only when
SERVIP2IPSECFL
AG is set to
ENABLE.
Indicates the third
service IPv6
NO NO No
an IPv6 path on the
S1 interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE,6 ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
and LOFD-002004 /
NO NO No
between the
eNodeB and the
SeGW for the IPv6
SGW to protect
data transmission
over the IPv6 Path
set up using the
third service IPv6
address for the S1
interface.
Indicates the name

of the SeGW used
when LBFD-003006 /
NO NO No
eNodeB.
Indicates the name

of the IP security
(IPsec) proposal,
LBFD-003006 /
IPsec negotiation
TDLBFD-003006
between the S-GW
LOFD-002004 /
TDLOFD-002004
eNodeB. This
LOFD-003024 /
parameter is valid
TDLOFD-003024
only when
SERVIP3IPSECFL
AG is set to
ENABLE.
service IPv6
NO NO No
an IPv6 path on the
S1 interface.
Indicates whether
to enable automatic
IPv6 IPSec MOs
(ACLRULE,6 ACL6,
IPSECPOLICY6,
and IPSECBIND6)
based on the other
user-configured
IPv6 IPSec MOs
and LOFD-002004 /
NO NO No
between the
eNodeB and the
SeGW for the IPv6
SGW to protect
data transmission
over the IPv6 Path
set up using the
fourth service IPv6
address for the S1
interface.
Indicates the name

of the SeGW used
when LBFD-003006 /
NO NO No
eNodeB.
Indicates the name

of the IP security
(IPsec) proposal,
LBFD-003006 /
IPsec negotiation
TDLBFD-003006
between the S-GW
LOFD-002004 /
TDLOFD-002004
eNodeB. This
LOFD-003024 /
parameter is valid
TDLOFD-003024
only when
SERVIP4IPSECFL
AG is set to
ENABLE.
LBFD-003006 /
Indicates the
TDLBFD-003006
LOFD-002004 /
SGW6.
TDLOFD-002004
Indicates the ID of
the operator that LBFD-003006 /
owns the IPv6 S- TDLBFD-003006
NO NO No
GW, by which the LOFD-002004 /
eNodeB identifies TDLOFD-002004
this IPv6 S-GW.
Indicates the
cabinet number of
LOFD-002004 /
TDLOFD-002004
X2 service IP
address is located.
Indicates the
subrack number of
LOFD-002004 /
TDLOFD-002004
X2 service IP
address is located.
Indicates the slot
number of the
LOFD-002004 /
board where the X2 NO YES No
TDLOFD-002004
service IP address
is located.
Indicates the ID of
LOFD-002004 /
the X2 service IP YES YES No
TDLOFD-002004
address.
Indicates the X2
service IP address
of the local
eNodeB, which is to
LOFD-002004 /
TDLOFD-002004
IP address for an
IP path on an X2
interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and a
LOFD-002004 /
neighboring
TDLOFD-002004
eNodeB to protect NO NO No
LOFD-003009 /
data transmission
TDLOFD-003009
on the IP path that
is set up using the
X2 service IP
address of the local
eNodeB.
Indicates whether
to enable the local
eNodeB to perform
IPSec negotiation
with the
neighboring
eNodeB through an
SeGW when
IPSECFLAG is set
to ENABLE. If this
LOFD-002004 /
parameter is set to
TDLOFD-002004
DISABLE, the local NO NO No
LOFD-003009 /
eNodeB directly
TDLOFD-003009
negotiates with the
neighboring
eNodeB. If this
parameter is set to
ENABLE, the local
eNodeB negotiates
with the
neighboring
eNodeB through an
SeGW.
Indicates the local

IP address used
when IPSECFLAG
LOFD-002004 /
is set to ENABLE.
TDLOFD-002004
The local eNodeB NO NO No
LOFD-003009 /
uses this IP
TDLOFD-003009
address in IKE
negotiation with a
peer device.
Indicates the name
of the SeGW used
when IPSECFLAG
and SEGWFLAG
LOFD-002004 /
are both set to NO NO No
TDLOFD-002004
ENABLE. The
SeGW performs
the local eNodeB.
Indicates the name

of the IPSec
proposal used
when IPSECFLAG
and SEGWFLAG
are both set to
LOFD-002004 /
ENABLE. This
TDLOFD-002004
IPSec proposal is NO NO No
LOFD-003009 /
required for IPSec
TDLOFD-003009
negotiation
between the local
eNodeB and a
neighboring
eNodeB through
the SeGW.
Indicates whether
to enable Ping
detection to check
the connectivity of
up IP path. If the
neighboring
eNodeB or the
LOFD-002004 /
firewall in the NO NO No
TDLOFD-002004
transport network is
configured to block
Ping packets, set
this parameter to
disable Ping
detection.
Otherwise, Ping
detection fails.

NO NO No
Indicates the
cabinet number of
LOFD-002004 /
TDLOFD-002004
X2 signaling IP
address is located.
Indicates the
subrack number of
LOFD-002004 /
TDLOFD-002004
X2 signaling IP
address is located.
Indicates the slot
number of the
LOFD-002004 /
TDLOFD-002004
signaling IP
address is located.
Indicates the ID of
LOFD-002004 /
the X2 signaling IP YES YES No
TDLOFD-002004
address.
Indicates the first

X2 signaling IP
eNodeB, which is to
LOFD-002004 /
TDLOFD-002004
local IP address for
up SCTP link on an
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and a
eNodeB to protect TDLOFD-002004
NO NO No
data transmission LOFD-003009 /
on the SCTP link TDLOFD-003009
that is set up using
the first X2
signaling IP
eNodeB.
Indicates whether
to enable the local
eNodeB to perform
IPSec negotiation
with the
neighboring
eNodeB through an
SeGW when
FIRSTIPSECFLAG
is set to ENABLE. If
set to DISABLE, the TDLOFD-002004
NO NO No
local eNodeB LOFD-003009 /
directly negotiates TDLOFD-003009
with the
neighboring
eNodeB. If this
parameter is set to
ENABLE, the local
eNodeB negotiates
with the
neighboring
eNodeB through an
SeGW.
Indicates the local
IP address used
when IPSECFLAG
LOFD-002004 /
is set to ENABLE.
TDLOFD-002004
LOFD-003009 /
uses this IP
TDLOFD-003009
address in IKE
negotiation with a
peer device.
Indicates the name

of the SeGW used
when IPSECFLAG
and SEGWFLAG LOFD-002004 /
are both set to TDLOFD-002004
NO NO No
SeGW performs TDLOFD-003009
a neighboring
eNodeB.
Indicates the name
of the IPSec
proposal used
when IPSECFLAG
and SEGWFLAG
are both set to
LOFD-002004 /
ENABLE. This
TDLOFD-002004
IPSec proposal is NO NO No
LOFD-003009 /
required for IPSec
TDLOFD-003009
negotiation
between the local
eNodeB and a
neighboring
eNodeB through
the SeGW.
Indicates the
second X2
signaling IP
eNodeB, which is to
LOFD-002004 /
TDLOFD-002004
second local IP
address for an
SCTP link on an X2
interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and a
NO NO No
the second X2
signaling IP
eNodeB.
Indicates whether
to enable the local
eNodeB to perform
IPSec negotiation
with the
neighboring
eNodeB through an
SeGW when
SECIPSECFLAG is
set to ENABLE. If
NO NO No
local eNodeB LOFD-003009 /
directly negotiates TDLOFD-003009
with the
neighboring
eNodeB. If this
parameter is set to
ENABLE, the local
eNodeB negotiates
with the
neighboring
eNodeB through an
SeGW.
Indicates the
second local IP
address used when
SECIPSECFLAG is
LOFD-002004 /
set to ENABLE. The NO NO No
TDLOFD-002004
local eNodeB uses
this IP address in
a peer device.
Indicates the name

of the SeGW used
when
SECIPSECFLAG
and LOFD-002004 /
SECSEGWFLAG TDLOFD-002004
NO NO No
are both set to LOFD-003009 /
SeGW performs
a neighboring
eNodeB.
Indicates the name
of the IPSec
proposal used
when
SECIPSECFLAG
and
LOFD-002004 /
SECSEGWFLAG
TDLOFD-002004
LOFD-003009 /
ENABLE. This
TDLOFD-003009
IPSec proposal is
required for IPSec
negotiation
between the local
eNodeB and the
SeGW.
Indicates the SCTP

port number of the
eNodeB, which is to
be used as the local
SCTP port number
created SCTP link
on an X2 interface.
If the
LOFD-002004 /
X2SonLinkSetupTy NO NO No
TDLOFD-002004
pe parameter in the
GlobalProcSwitch
MO is set to
X2_OVER_S1 or is
to be changed to
X2_OVER_S1 from
X2_OVER_M2000,
this parameter must
be set to 36422.
Indicates the
minimum
Retransmission
Timeout (RTO)
value for the SCTP
link. A smaller value
of this parameter
indicates a shorter LOFD-002004 /
NO NO No
time required to TDLOFD-002004
check link
connectivity. The
time required to
check link
connectivity is twice
the sum of the new
RTO and heartbeat
Indicates the
maximum RTO
value of an SCTP
link. A larger value LOFD-002004 /
NO NO No
indicates a longer TDLOFD-002004
period required for
checking link
connectivity.

value of the
Retransmission
TimeOut (RTO). It is
used as the initial LOFD-002004 /
NO NO No
value when TDLOFD-002004
calculating the
retransmission
timeout in the SCTP
protocol.
Indicates the value

of RtoAlpha. It is
used as smooth
factor of the round-
trip delay
calculation in the
SCTP protocol. In a LOFD-002004 /
NO NO No
new estimation, TDLOFD-002004
(RtoAlpha/100) is
taken from a new
measurement, and
1-(RtoAlpha/100) is
taken from the last
estimation.
Indicates the value

of RtoBeta. It is
used as smooth
factor of the round-
trip delay
calculation in the
SCTP protocol. In a LOFD-002004 /
NO NO No
new estimation, TDLOFD-002004
(RtoBeta/100) is
taken from the
offset gain, and 1-
(RtoBeta/100) is
taken from the last
estimation.
Indicates the
heartbeat interval,
corresponding to
the HBInter
parameter specified
in RFC4960. SCTP
periodically
transmits heartbeat
messages to an idle
destination address
to detect the LOFD-002004 /
NO NO No
reachability. TDLOFD-002004
According to
RFC4960, the
actual interval at
which heartbeat
messages are
transmitted equals
the parameter value
(HBInter) plus the
retransmission
timeout (RTO).
Indicates the
maximum number
of retransmissions
on the SCTP link. If
the number of
retransmissions on
LOFD-002004 /
the SCTP link NO NO No
TDLOFD-002004
reaches this
parameter value,
the eNodeB breaks
this SCTP link and
reports a link failure
alarm.
Indicates the
maximum number
of retransmissions
over a path. When
the number of
retransmissions
over a path
exceeds the value
of this parameter, LOFD-002004 /
NO NO No
the path is regarded TDLOFD-002004
as failed if no
heartbeat
acknowledgment is
paths are used,
path switchover is
automatically
performed.
Indicates whether
to calculate the
checksum of each
message to be
transmitted.
set to ENABLE, the
local eNodeB
calculates the LOFD-002004 /
NO NO No
checksum. If the TDLOFD-002004
calculated
checksum is
different from that
contained in the
message, the local
eNodeB does not
transmit the
message.
Indicates whether
to calculate the
checksum of each
received message.
set to ENABLE, the
local eNodeB
calculates the LOFD-002004 /
NO NO No
checksum. If the TDLOFD-002004
calculated
checksum is
different from that
contained in the
message, the local
eNodeB discards
the message.
Indicates the type

LOFD-002004 /
of the checksum NO NO No
TDLOFD-002004
calculation.
Indicates whether
to switch back to
the primary path of
up SCTP link when
the primary path is LOFD-002004 /
NO NO No
restored. When the TDLOFD-002004
primary path of an
SCTP link becomes
unreachable, the
secondary path
takes over.
Indicates the
number of
consecutive
heartbeat
messages that
must be transmitted
on the primary path
LOFD-002004 /
before the eNodeB NO NO No
TDLOFD-002004
can switch back to
the primary path.
This parameter is
valid only when the
SWITCHBACKFLA
G parameter is set
to ENABLE.
Indicates the time

interval that one
end of SCTP link
can send an SACK
message in
response to the
reception of certain
LOFD-002004 /
data. A larger value NO NO No
TDLOFD-002004
of this parameter
indicates a longer
time interval
between the
reception of data
and the sending of
the corresponding
SACK message.

NO NO No

YES YES No
the X2eNodeB. TDLOFD-002004
Indicates the first
signaling IP
address of the
neighboring
eNodeB, which is to LOFD-002004 /
NO YES No
be used as the first TDLOFD-002004
peer IP address for
up SCTP link on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and
the neighboring LOFD-002004 /
NO NO No
the first signaling IP
address of the
neighboring
eNodeB.
Indicates whether
to enable the
neighboring
eNodeB to perform
IPSec negotiation
with the local
eNodeB through an
SeGW when
FIRSTIPSECFLAG
is set to ENABLE. If
LOFD-002004 /
this parameter is
TDLOFD-002004
set to DISABLE, the NO NO No
LOFD-003009 /
neighboring
TDLOFD-003009
eNodeB directly
negotiates with the
local eNodeB. If this
parameter is set to
ENABLE, the
neighboring
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the first

local IP address
used when
FIRSTIPSECFLAG LOFD-002004 /
NO NO No
The neighboring LOFD-003009 /
IP address in IKE
local eNodeB.
Indicates the
second signaling IP
address of the
neighboring
eNodeB, which is to
LOFD-002004 /
TDLOFD-002004
second peer IP
address for an
SCTP link on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and
the neighboring
LOFD-002004 /
eNodeB to protect
TDLOFD-002004
data transmission NO NO No
LOFD-003009 /
on the SCTP link
TDLOFD-003009
the second
signaling IP
address of the
neighboring
eNodeB.
Indicates whether
the neighboring
eNodeB is enabled
to perform IPSec
local eNodeB
through an SeGW
when
SECIPSECFLAG is
set to ENABLE. If
LOFD-002004 /
this parameter is
TDLOFD-002004
set to DISABLE, the NO NO No
LOFD-003009 /
neighboring
TDLOFD-003009
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the
neighboring
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the
second local IP
address used when
SECIPSECFLAG is LOFD-002004 /
set to ENABLE. The TDLOFD-002004
NO NO No
IP address in IKE
local eNodeB.
Indicates the SCTP

port number of the
neighboring
eNodeB, which is to
be used as the peer
SCTP port number
set up SCTP link on
LOFD-002004 /
the X2 interface. If NO NO No
TDLOFD-002004
the
X2SonLinkSetupTy
pe parameter in the
GlobalProcSwitch
MO is set to
X2_OVER_S1, this
parameter must be
set to 36422.
Indicates the first
service IP address
of the neighboring
NO NO No
be used in TDLOFD-002004
automatic setup of
an IP path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and
NO NO No
on the IP path that TDLOFD-003009
is set up using the
first service IP
address of the
neighboring
eNodeB.
Indicates whether
the neighboring
eNodeB is enabled
to perform IPSec
local eNodeB
through an SeGW
when
SERVIP1IPSECFL
AG is set to
ENABLE. If this LOFD-002004 /
NO NO No
DISABLE, the LOFD-003009 /
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the
neighboring
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the first

local IP address
used when
SERVIP1IPSECFL
LOFD-002004 /
AG is set to
TDLOFD-002004
ENABLE. The NO NO No
LOFD-003009 /
neighboring
TDLOFD-003009
eNodeB uses this
IP address in IKE
local eNodeB.
Indicates the
second service IP
address of the
neighboring
LOFD-002004 /
eNodeB, which is to NO NO No
TDLOFD-002004
be used in
automatic setup of
an IP path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and
NO NO No
is set up using the
second service IP
address of the
neighboring
eNodeB.
Indicates whether
the neighboring
eNodeB is enabled
to perform IPSec
local eNodeB
through an SeGW
when
SERVIP2IPSECFL
AG is set to
NO NO No
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the
neighboring
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the
second local IP
address used when
SERVIP2IPSECFL
LOFD-002004 /
AG is set to
TDLOFD-002004
LOFD-003009 /
neighboring
TDLOFD-003009
eNodeB uses this
IP address in IKE
local eNodeB.
Indicates the third
service IP address
of the neighboring
NO NO No
automatic setup of
an IP path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and
NO NO No
is set up using the
third service IP
address of the
neighboring
eNodeB.
Indicates whether
the neighboring
eNodeB is enabled
to perform IPSec
local eNodeB
through an SeGW
when
SERVIP3IPSECFL
AG is set to
NO NO No
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the
neighboring
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the third

local IP address
used when
SERVIP3IPSECFL
LOFD-002004 /
AG is set to
TDLOFD-002004
LOFD-003009 /
neighboring
TDLOFD-003009
eNodeB uses this
IP address in IKE
local eNodeB.
service IP address
of the neighboring
NO NO No
automatic setup of
an IP path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPSec
tunnel between the
local eNodeB and
NO NO No
is set up using the
fourth service IP
address of the
neighboring
eNodeB.
Indicates whether
the neighboring
eNodeB is enabled
to perform IPSec
local eNodeB
through an SeGW
when
SERVIP4IPSECFL
AG is set to
NO NO No
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the
neighboring
eNodeB negotiates
with the local
eNodeB through an
SeGW.

local IP address
used when
SERVIP4IPSECFL
LOFD-002004 /
AG is set to
TDLOFD-002004
LOFD-003009 /
neighboring
TDLOFD-003009
eNodeB uses this
IP address in IKE
local eNodeB.

country code (MCC)
of the neighboring
eNodeB. An MCC
consists of three
digits.In RAN
sharing with LOFD-002004 /
NO NO No
common carriers TDLOFD-002004
scenarios, this
parameter indicates
the MCC of the
primary operator of
the neighboring
eNodeB.
network code
(MNC) of the
neighboring
eNodeB. An MNC
consists of two or
three digits.In RAN
LOFD-002004 /
sharing with NO NO No
TDLOFD-002004
common carriers
scenarios, this
parameter indicates
the MNC of the
primary operator of
the neighboring
eNodeB.
Indicates the ID of
LOFD-002004 /
the neighboring NO NO No
TDLOFD-002004
eNodeB.
Indicates the
LOFD-002004 /
TDLOFD-002004
X2eNodeB.
Indicates the ID of
the operator that
LOFD-002004 /
owns the NO NO No
TDLOFD-002004
neighboring
eNodeB.
Indicates the
compliance protocol
LOFD-002004 /
release of the NO NO No
TDLOFD-002004
neighboring
eNodeB.
LBFD-003006 /
Indicates the ID of
TDLBFD-003006
the X2 service IPv6 YES YES No
LOFD-002004 /
address.
TDLOFD-002004
Indicates the
LBFD-003006 /
cabinet number of
TDLBFD-003006
LOFD-002004 /
X2 service IPv6
TDLOFD-002004
address is located.
Indicates the
LBFD-003006 /
subrack number of
TDLBFD-003006
LOFD-002004 /
X2 service IPv6
TDLOFD-002004
address is located.
Indicates the slot
LBFD-003006 /
number of the
TDLBFD-003006
LOFD-002004 /
service IPv6
TDLOFD-002004
address is located.
Indicates the X2
service IPv6
LBFD-003006 /
eNodeB, which is to
TDLBFD-003006
LOFD-002004 /
IPv6 address for an
TDLOFD-002004
IPv6 path on an S1
interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local LBFD-003006 /
eNodeB and a TDLBFD-003006
neighboring IPv6 LOFD-002004 /
NO NO No
on the IPv6 path TDLOFD-003024
the X2 service IPv6
eNodeB.
Indicates whether
to enable the local
eNodeB to perform
IPv6 IPSec
neighboring IPv6
eNodeB through an
SeGW when
SERVIPSECFLAG
is set to ENABLE. If LBFD-003006 /
this parameter is TDLBFD-003006
set to DISABLE, the LOFD-002004 /
NO NO No
local eNodeB TDLOFD-002004
directly negotiates LOFD-003024 /
with the TDLOFD-003024
neighboring IPv6
eNodeB. If this
parameter is set to
ENABLE, the local
eNodeB negotiates
with the
neighboring IPv6
eNodeB through an
SeGW.
Indicates the local

IPv6 address used
LBFD-003006 /
when IPSECFLAG
TDLBFD-003006
is set to ENABLE.
LOFD-002004 /
TDLOFD-002004
uses this IPv6
LOFD-003024 /
address in IPv6 IKE
TDLOFD-003024
negotiation with a
peer device.
Indicates the name
of the IPv6 IKE
peer used when
SERVIPSECFLAG LBFD-003006 /
and TDLBFD-003006
SERVIPSECGWFL LOFD-002004 /
NO NO No
AG are both set to TDLOFD-002004
ENABLE. The IPv6 LOFD-003024 /
IKE peer performs TDLOFD-003024
IPv6 IKE
local eNodeB.
Indicates the name

of the IPsec
proposal used in
IPsec negotiation
between the local LBFD-003006 /
eNodeB and the TDLBFD-003006
security gateway LOFD-002004 /
NO NO No
(SeGW). This TDLOFD-002004
parameter is valid LOFD-003024 /
only when TDLOFD-003024
IPSECFLAG and
SEGWFLAG are
both set to
ENABLE.
Indicates whether
to enable Ping
detection to check
the connectivity of
up IP path. If the
neighboring
LBFD-003006 /
eNodeB or the
TDLBFD-003006
firewall in the NO NO No
LOFD-002004 /
transport network is
TDLOFD-002004
configured to block
Ping packets, set
this parameter to
disable Ping
detection.
Otherwise, Ping
detection fails.
Indicates the ID of
LBFD-003006 /
the operator that
TDLBFD-003006
owns the X2 NO NO No
LOFD-002004 /
service IPv6
TDLOFD-002004
address.
LBFD-003006 /
Indicates the ID of
TDLBFD-003006
the X2 signaling YES YES No
LOFD-002004 /
IPv6 address.
TDLOFD-002004
Indicates the
LBFD-003006 /
cabinet number of
TDLBFD-003006
LOFD-002004 /
X2 signaling IPv6
TDLOFD-002004
address is located.
Indicates the
LBFD-003006 /
subrack number of
TDLBFD-003006
LOFD-002004 /
X2 signaling IPv6
TDLOFD-002004
address is located.
Indicates the slot
LBFD-003006 /
number of the
TDLBFD-003006
LOFD-002004 /
signaling IPv6
TDLOFD-002004
address is located.
Indicates the first

X2 signaling IPv6
eNodeB, which is to LBFD-003006 /
be used as the first TDLBFD-003006
NO YES No
local IPv6 address LOFD-002004 /
set up IPv6 SCTP
link on an X2
interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
LBFD-003006 /
eNodeB and a
TDLBFD-003006
neighboring IPv6
LOFD-002004 /
TDLOFD-002004
data transmission
LOFD-003024 /
on the IPv6 SCTP
TDLOFD-003024
link that is set up
using the first X2
signaling IPv6
eNodeB.
Indicates whether
to enable the local
eNodeB to perform
IPv6 IPSec
negotiation with a
neighboring IPv6
eNodeB through an
SeGW when
SIGIP1SECFLAG is
set to ENABLE. If LBFD-003006 /
NO NO No
neighboring IPv6
eNodeB. If this
parameter is set to
ENABLE, the local
eNodeB negotiates
with the
neighboring IPv6
eNodeB through an
SeGW.
Indicates the first
local IPv6 address
used when LBFD-003006 /
NO NO No
local eNodeB uses TDLOFD-002004
negotiation with a
peer device.
Indicates the name

of the IPv6 IKE
peer used when
SIGIP1SECFLAG LBFD-003006 /
and TDLBFD-003006
SIGIP1SEGWFLAG LOFD-002004 /
NO NO No
are both set to TDLOFD-002004
ENABLE. This IPv6 LOFD-003024 /
IKE peer performs TDLOFD-003024
IPv6 IKE
negotiation with a
local IPv6 eNodeB.
Indicates the name
of the IPSec
proposal used
when
SIGIP1SECFLAG
LBFD-003006 /
and
TDLBFD-003006
SIGIP1SEGWFLAG
LOFD-002004 /
TDLOFD-002004
ENABLE. This IPv6
LOFD-003024 /
IPSec proposal is
TDLOFD-003024
required for IPv6
IPSec negotiation
between the local
eNodeB and the
IPv6 SeGW.
Indicates the
second X2
signaling IPv6
LBFD-003006 /
eNodeB, which is to
TDLBFD-003006
LOFD-002004 /
second local IPv6
TDLOFD-002004
address for an
IPv6 SCTP link on
an X2 interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
LBFD-003006 /
eNodeB and a
TDLBFD-003006
neighboring IPv6
LOFD-002004 /
TDLOFD-002004
data transmission
LOFD-003024 /
on the IPv6 SCTP
TDLOFD-003024
link that is set up
using the second
X2 signaling IPv6
eNodeB.
Indicates whether
to enable the local
eNodeB to perform
IPv6 IPSec
negotiation with a
neighboring IPv6
eNodeB through an
SeGW when
SIGIP2SECFLAG is
set to ENABLE. If LBFD-003006 /
NO NO No
neighboring IPv6
eNodeB. If this
parameter is set to
ENABLE, the local
eNodeB negotiates
with the
neighboring IPv6
eNodeB through an
SeGW.
Indicates the
second local IPv6
address used when LBFD-003006 /
NO NO No
local eNodeB uses TDLOFD-002004
negotiation with a
peer device.
Indicates the name

of the IPv6 IKE
peer used when
SIGIP2SECFLAG
LBFD-003006 /
and
TDLBFD-003006
SIGIP2SEGWFLAG
LOFD-002004 /
TDLOFD-002004
ENABLE. This IPv6
LOFD-003024 /
IKE peer performs
TDLOFD-003024
IPv6 IKE
negotiation with a
neighboring IPv6
eNodeB.
Indicates the name
of the IPSec
proposal used
when
SIGIP2SECFLAG
LBFD-003006 /
and
TDLBFD-003006
SIGIP2SEGWFLAG
LOFD-002004 /
TDLOFD-002004
ENABLE. This IPv6
LOFD-003024 /
IPSec proposal is
TDLOFD-003024
required for IPv6
IPSec negotiation
between the local
eNodeB and the
IPv6 SeGW.
Indicates the IPv6

SCTP port number
of the eNodeB,
which is to be used
as the local IPv6
SCTP port number
created IPv6 SCTP
link on an X2 LBFD-003006 /
interface. If the TDLBFD-003006
NO NO No
X2SonLinkSetupTy LOFD-002004 /
pe parameter in the TDLOFD-002004
GlobalProcSwitch
MO is set to
X2_OVER_S1 or is
to be changed to
X2_OVER_S1 from
X2_OVER_M2000,
this parameter must
be set to 36422.
Indicates the
minimum
retransmission
timeout (RTO)
value of an IPv6 LBFD-003006 /
SCTP link. The time TDLBFD-003006
NO NO No
that a link LOFD-002004 /
connectivity check TDLOFD-002004
value of this
parameter.
Indicates the
maximum RTO
value of an IPv6
LBFD-003006 /
SCTP link. The time
TDLBFD-003006
that a link check NO NO No
LOFD-002004 /
TDLOFD-002004
value of this
parameter.
RTO value of an
IPv6 SCTP link.
LBFD-003006 /
The time that a link
TDLBFD-003006
connectivity check NO NO No
LOFD-002004 /
TDLOFD-002004
value of this
parameter.
Indicates the Alpha

value for RTO for
an IPv6 SCTP link.
A larger value of
LBFD-003006 /
this parameter
TDLBFD-003006
LOFD-002004 /
sensitivity of the
TDLOFD-002004
IPv6 SCTP link to
the time delay. For
details, see
RFC4960.
Indicates the Beta
value for RTO for
an IPv6 SCTP link.
A larger value of
LBFD-003006 /
this parameter
TDLBFD-003006
LOFD-002004 /
sensitivity of the
TDLOFD-002004
IPv6 SCTP link to
the time delay. For
details, see
RFC4960.
Indicates the
heartbeat interval of
the IPv6 SCTP link.
The status of an
IPv6 SCTP link is
checked by each
end sending
heartbeat
messages to the
other end. If one
end receives one
heartbeat
acknowledgment,
LBFD-003006 /
then it considers
TDLBFD-003006
the IPv6 SCTP link NO NO No
LOFD-002004 /
as connected.
TDLOFD-002004
However, if one end
has transmitted
heartbeat
messages for a
number equal to the
MAXASSOCRETR
value but has not
received any
heartbeat
acknowledgments,
then it considers
the IPv6 SCTP link
as broken.
Indicates the
maximum number
of retransmissions
over an IPv6 SCTP
link. If this IPv6
SCTP link has
multiple paths, then
this IPv6 SCTP link
is also called an
IPv6 SCTP
association and this
parameter indicates
LBFD-003006 /
the maximum
TDLBFD-003006
number of NO NO No
LOFD-002004 /
retransmissions
TDLOFD-002004
over an IPv6 SCTP
association. When
the number of
retransmissions on
the association
exceeds the value
of this parameter,
the eNodeB
considers the IPv6
SCTP link as
broken and reports
a link failure alarm.
Indicates the
maximum number
of retransmissions
over a path. If the
number of
retransmissions
over a path
exceeds the value
of this parameter
LBFD-003006 /
but no response
TDLBFD-003006
message is NO NO No
LOFD-002004 /
received, the
TDLOFD-002004
eNodeB considers
this path as
unreachable. If the
IPv6 SCTP link
uses multihoming,
that is, multiple
paths, the eNodeB
switches to another
path.
Indicates whether
to calculate the
checksum of each
message to be
transmitted. If the
calculated
checksum of a LBFD-003006 /
message is different TDLBFD-003006
NO NO No
from the checksum LOFD-002004 /
contained in the TDLOFD-002004
message, the
eNodeB considers
this message to
have bit errors and
does not transmit
the message.

to check the TDLBFD-003006
NO NO No
checksum of each LOFD-002004 /
received message. TDLOFD-002004
checksum TDLBFD-003006
NO NO No
calculation LOFD-002004 /
algorithm. TDLOFD-002004
Indicates whether
to switch back to
the primary path
when the primary
path is restored.
When the primary
path is
LBFD-003006 /
unreachable, the
TDLBFD-003006
eNodeB switches to NO NO No
LOFD-002004 /
the secondary path.
TDLOFD-002004
This parameter is
used to set whether
the eNodeB
switches back to
the primary path
when the primary
path is restored.
Indicates the
number of
consecutive
heartbeat response
messages that
must be detected
over the primary
path of an IPv6
SCTP link before
the eNodeB can
LBFD-003006 /
switch back to this
TDLBFD-003006
primary path. After NO NO No
LOFD-002004 /
the primary path is
TDLOFD-002004
restored and the
number of
consecutive
heartbeat response
messages reaches
the value of this
parameter, the
eNodeB switches
back to the primary
path.
Indicates the ID of
LBFD-003006 /
the operator that
TDLBFD-003006
owns the X2 NO NO No
LOFD-002004 /
signaling IPv6
TDLOFD-002004
address.
LBFD-003006 /
Indicates the ID of
TDLBFD-003006
the neighboring YES YES No
LOFD-002004 /
IPv6 eNodeB.
TDLOFD-002004
Indicates the first
signaling IPv6
address of the
neighboring IPv6
LBFD-003006 /
eNodeB, which is to
TDLBFD-003006
LOFD-002004 /
peer IPv6 address
TDLOFD-002004
set up IPv6 SCTP
link on the X2
interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
eNodeB and the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
eNodeB. The IPv6
LOFD-002004 /
IPSec tunnel is NO NO No
TDLOFD-002004
used to protect data
LOFD-003024 /
transmission on the
TDLOFD-003024
IPv6 SCTP link that
is set up using the
first signaling IPv6
address of the
neighboring IPv6
eNodeB.
Indicates whether
to enable the
neighboring IPv6
eNodeB to perform
IPv6 IPSec
local eNodeB
through an SeGW
when
SIGIP1SECFLAG is LBFD-003006 /
set to ENABLE. If TDLBFD-003006
NO NO No
eNodeB directly TDLOFD-003024
negotiates with the
parameter is set to
ENABLE, the
neighboring IPv6
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the local

IPv6 address used
by the neighboring
IPv6 eNodeB in
IPv6 IKE
negotiation with the LBFD-003006 /
local eNodeB. The TDLBFD-003006
value of this LOFD-002004 /
NO NO No
parameter is the TDLOFD-002004
same as the value LOFD-003024 /
of the SIGIKEIP1 TDLOFD-003024
parameter in the
X2SigIP6 MO
configured on the
neighboring IPv6
eNodeB.
Indicates the
second signaling
IPv6 address of the
neighboring IPv6
LBFD-003006 /
eNodeB, which is to
TDLBFD-003006
LOFD-002004 /
second peer IPv6
TDLOFD-002004
address for an
IPv6 SCTP link on
the X2 interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
eNodeB and the LBFD-003006 /
neighboring IPv6 TDLBFD-003006
eNodeB to protect LOFD-002004 /
NO NO No
data transmission TDLOFD-002004
on the SCTP link LOFD-003024 /
that is set up using TDLOFD-003024
the second
signaling IPv6
address of the
neighboring IPv6
eNodeB.
Indicates whether
to enable the
neighboring IPv6
eNodeB to perform
IPv6 IPSec
local eNodeB
through an SeGW
when
SIGIP2SECFLAG is LBFD-003006 /
set to ENABLE. If TDLBFD-003006
NO NO No
eNodeB directly TDLOFD-003024
negotiates with the
parameter is set to
ENABLE, the
neighboring IPv6
eNodeB negotiates
with the local
eNodeB through an
SeGW.
Indicates the local

IPv6 address used
by the neighboring
IPv6 eNodeB in
IPv6 IKE
negotiation with the LBFD-003006 /
local eNodeB. The TDLBFD-003006
NO NO No
parameter is the TDLOFD-002004
same as the value LOFD-003024 /
of the SIGIKEIP2 TDLOFD-003024
parameter in the
X2SigIP6 MO
configured on the
neighboring IPv6
eNodeB.
Indicates the SCTP
port number of the
neighboring IPv6
eNodeB, which is to
be used as the peer
SCTP port number
LBFD-003006 /
set up IPv6 SCTP
TDLBFD-003006
link on the X2 NO NO No
LOFD-002004 /
interface. If the
TDLOFD-002004
X2SonLinkSetupTy
pe parameter in the
GLOBALPROCSWI
TCH MO is set to
X2_OVER_S1, this
parameter must be
set to 36422.
Indicates the first

service IPv6
address of the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
be used in
TDLOFD-002004
automatic setup of
an IPv6 path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
eNodeB and the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
data transmission
TDLOFD-002004
on the IPv6 path
the first service
IPv6 address of the
neighboring IPv6
eNodeB.
Indicates whether
to enable the peer
eNodeB to perform
IP security (IPsec)
local eNodeB
through a security
gateway (SeGW).
This parameter is
valid only when
SERVIP1IPSECFL LBFD-003006 /
AG is set to TDLBFD-003006
NO NO No
DISABLE, the peer
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the peer
eNodeB negotiates
with the local
eNodeB through
the SeGW.
Indicates the local

IPv6 address used
by the neighboring
IPv6 eNodeB in
IPv6 IKE
local eNodeB. The LBFD-003006 /
NO NO No
parameter is the LOFD-002004 /
same as the value TDLOFD-002004
of the SERVIKEIP
parameter in the
X2ServIP6 MO
configured on the
neighboring IPv6
eNodeB.
Indicates the
second service
IPv6 address of the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
be used in
TDLOFD-002004
automatic setup of
an IPv6 path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
eNodeB and the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
data transmission
TDLOFD-002004
on the IPv6 path
the second service
IPv6 address of the
neighboring IPv6
eNodeB.
Indicates whether
to enable the peer
eNodeB to perform
IP security (IPsec)
local eNodeB
through a security
gateway (SeGW).
This parameter is
valid only when
NO NO No
DISABLE, the peer
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the peer
eNodeB negotiates
with the local
eNodeB through
the SeGW.
Indicates the local

IPv6 address used
by the neighboring
IPv6 eNodeB in
IPv6 IKE
NO NO No
of the SERVIKEIP
parameter in the
X2ServIP6 MO
configured on the
neighboring IPv6
eNodeB.
Indicates the third
service IPv6
address of the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
be used in
TDLOFD-002004
automatic setup of
an IPv6 path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
eNodeB and the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
data transmission
TDLOFD-002004
on the IPv6 path
the third service
IPv6 address of the
neighboring IPv6
eNodeB.
Indicates whether
to enable the peer
eNodeB to perform
IP security (IPsec)
local eNodeB
through a security
gateway (SeGW).
This parameter is
valid only when
NO NO No
DISABLE, the peer
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the peer
eNodeB negotiates
with the local
eNodeB through
the SeGW.
Indicates the local

IPv6 address used
by the neighboring
IPv6 eNodeB in
IPv6 IKE
NO NO No
of the SERVIKEIP
parameter in the
X2ServIP6 MO
configured on the
neighboring IPv6
eNodeB.
service IPv6
address of the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
be used in
TDLOFD-002004
automatic setup of
an IPv6 path on the
X2 interface.
Indicates whether
to enable automatic
setup of an IPv6
IPSec tunnel
between the local
eNodeB and the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
LOFD-002004 /
data transmission
TDLOFD-002004
on the IPv6 path
the fourth service
IPv6 address of the
neighboring IPv6
eNodeB.
Indicates whether
to enable the peer
eNodeB to perform
IP security (IPsec)
local eNodeB
through a security
gateway (SeGW).
This parameter is
valid only when
NO NO No
DISABLE, the peer
eNodeB directly
negotiates with the
parameter is set to
ENABLE, the peer
eNodeB negotiates
with the local
eNodeB through
the SeGW.
Indicates the local

IPv6 address used
by the neighboring
IPv6 eNodeB in
IPv6 IKE
NO NO No
of the SERVIKEIP
parameter in the
X2ServIP6 MO
configured on the
neighboring IPv6
eNodeB.

country code (MCC)
of the neighboring
IPv6 eNodeB. An
MCC consists of
three digits.In RAN LBFD-003006 /
sharing with TDLBFD-003006
NO NO No
common carriers LOFD-002004 /
scenarios, this TDLOFD-002004
parameter indicates
the MCC of the
primary operator of
the neighboring
IPv6 eNodeB.
network code
(MNC) of the
neighboring IPv6
eNodeB. An MNC
consists of two or
LBFD-003006 /
three digits.In RAN
TDLBFD-003006
sharing with NO NO No
LOFD-002004 /
common carriers
TDLOFD-002004
scenarios, this
parameter indicates
the MNC of the
primary operator of
the neighboring
IPv6 eNodeB.
LBFD-003006 /
NO NO No
the peer eNodeB. LOFD-002004 /
TDLOFD-002004
LBFD-003006 /
Indicates the
TDLBFD-003006
description of NO NO No
LOFD-002004 /
X2eNodeB6.
TDLOFD-002004
Indicates the ID of
the operator that
owns the
LBFD-003006 /
neighboring IPv6
TDLBFD-003006
eNodeB, by which NO NO No
LOFD-002004 /
the local eNodeB
TDLOFD-002004
identifies the
neighboring IPv6
eNodeB.
Indicates the
LBFD-003006 /
compliance protocol
TDLBFD-003006
release of the NO NO No
LOFD-002004 /
neighboring
TDLOFD-002004
eNodeB.

YES YES No
of the CA. TDLOFD-003010
Indicates the URL

of the CA. The URL
can be either an
HTTP or HTTPS
URL. The IP
LOFD-003010 /
address in the URL NO YES No
TDLOFD-003010
must be a valid IP
address. The
default port number
is 80 for HTTP or
443 for HTTPS.
Indicates the
signature algorithm
for message of
CMP. The signature
algorithm can be NO NO No None
Secure Hash
Algorithm 1 (SHA1)
or Hash Algorithm
256 (SHA256).
for configuring the
following
parameters:
-Certificate Update
Source IP
-CA URL During
Site Deployment
-Source IP for
Applying for a
Certificate During
Site Deployment
set to
DEFAULT_MODE,
all of the preceding
parameters do not
need to be
configured; the BS
NO NO No None
automatically uses
the OM IP address
of the main control
board as the source
IP address to apply
and update a
certificate. If this
parameter is set to
CFG_INIT_UPD_A
DDR, all of the
preceding
parameters need to
be configured. If
this parameter is
set to
CFG_UPD_SIP,
only Certificate
Update Source IP
needs to be set.
Indicates the
source IP address
used when a
certificate is
updated. If the
source IP for
applying for a
certificate during NO NO No None
site deployment is
not configured, this
parameter can also
be used as the
source IP address
during site
deployment.
Indicates the URL

of the CA that is
used during site
deployment. The
URL can be either
an HTTP or HTTPS
URL. In the URL,
the IP address must
be a valid IP
address, and the
NO YES No None
default port number
is 80 for HTTP or
443 for HTTPS.
This parameter is
mandatory when
the CA uses
different URLs
during site
deployment or
certificate update.
Indicates the
source IP address
for the BS to
access the CA and
to initially obtain a
certificate. This
parameter is
mandatory when
the CA uses
NO YES No None
different URLs in
the following
scenarios:
-The BS initially
obtains a certificate
during site
deployment.
-A certificate is
updated.
Indicates the
common name of
the certificate
request file, which
can be the
LOFD-003010 /
electronic serial NO NO No
TDLOFD-003010
number (ESN),
media access
control (MAC)
address, or IP
address of a board.
Indicates the
additional
information about a
certificate common
name. The
information will be
added behind the
value of the
LOFD-003010 /
COMMNAME NO NO No
TDLOFD-003010
parameter to
compose a
complete common
name for a
certificate request
file. The default
value is
.huawei.com.
Indicates the
LOFD-003010 /
country where a BS NO NO No
TDLOFD-003010
is located.
Indicates the
LOFD-003010 /
organization that NO NO No
TDLOFD-003010
owns a BS.
Indicates the
LOFD-003010 /
organization unit NO NO No
TDLOFD-003010
that owns a BS.
Indicates the state
LOFD-003010 /
or province where a NO NO No
TDLOFD-003010
BS is located.

NO NO No
location of a BS. TDLOFD-003010
Indicates the usage

for a key, including
KEY_AGREEMENT
(key negotiation),
DATA_ENCIPHER
MENT (data
encryption),
KEY_ENCIPHERM LOFD-003010 /
NO NO No
ENT (key TDLOFD-003010
encryption), and
DIGITAL_SIGNATU
RE (digital
signature). This
parameter can be
set to one or
multiple values.
Indicates the
signature algorithm
for a certificate
request file. The
signature algorithm
can be Secure LOFD-003010 /
NO NO No
Hash Algorithm 1 TDLOFD-003010
(SHA1), Message-
Digest Algorithm 5
(MD5) or Hash
Algorithm 256
(SHA256).
of a key, which can LOFD-003010 /
NO NO No
be 1024 bits or TDLOFD-003010
2048 bits.
Indicates the local
name of a BS. This
parameter is used
to generate the
DNS name of the
subject alternative
name of a
certificate, so as to
verify the peer's
LOFD-003010 /
identification in IKE NO NO No
TDLOFD-003010
negotiation. If this
parameter is not
configured, the BS
automatically uses
the common name
and its additional
information to
generate the DNS
name.
Indicates the local LOFD-003010 /

NO NO No
IP address of a BS. TDLOFD-003010
Indicates the file

name of a device
certificate. The file
name cannot
include any of the
following
characters:
backslashes (\), LOFD-003010 /
YES YES No
slashes (/), colons TDLOFD-003010
(:), asterisks (*),
question marks (?),
double quotation
marks ("), left angle
brackets (<), right
angle brackets (>),
and bars (|).

LOFD-003010 /
number of a device NO NO Yes
TDLOFD-003010
certificate.
Indicates the
LOFD-003010 /
common name of a NO NO Yes
TDLOFD-003010
device certificate.
Indicates the issuer
LOFD-003010 /
of a device NO NO Yes
TDLOFD-003010
certificate.
Indicates the
LOFD-003010 /
expiration date of a NO NO Yes
TDLOFD-003010
device certificate.
Indicates the date
when a device LOFD-003010 /
NO NO Yes
certificate begins to TDLOFD-003010
take effect.
Indicates the
application type of
activated device LOFD-003010 /
YES YES No
certificate. There TDLOFD-003010
are two types: IKE
and SSL.
Indicates the file
name of an
activated device
name cannot
include any of the
following
characters:
LOFD-003010 /
backslashes (\), NO YES No
TDLOFD-003010
slashes (/), colons
(:), asterisks (*),
question marks (?),
double quotation
brackets (<), right
angle brackets (>),
and bars (|).
LOFD-003010 /
of an activated NO NO Yes
TDLOFD-003010
device certificate.
Indicates the
common name of LOFD-003010 /
NO NO Yes
an activated device TDLOFD-003010
certificate.
number of an LOFD-003010 /
NO NO Yes
activated device TDLOFD-003010
certificate.
Indicates the
expiration date of LOFD-003010 /
NO NO Yes
an activated device TDLOFD-003010
certificate.
Indicates the IKE
name of the peer
device, which is
used in IKE
local end to test an
activated device
LOFD-003010 /
certificate. This NO NO No
TDLOFD-003010
parameter is used
only in the TST
APPCERT
command in the
current version and
will be removed in
later versions.
Indicates the date

when an activated
LOFD-003010 /
device certificate NO NO Yes
TDLOFD-003010
begins to take
effect.
Indicates the
loading status of an LOFD-003010 /
NO NO Yes
activated device TDLOFD-003010
certificate.
Indicates the
certificate LOFD-003010 /
NO NO Yes
application type TDLOFD-003010
supported by a BS.
Indicates the name

of the cross-
name cannot
include any of the
following
characters:
YES YES No
(:), asterisks (*),
question marks (?),
double quotation
brackets (<), right
angle brackets (>),
and bars (|).
LOFD-003010 /
number of the NO NO Yes
TDLOFD-003010
cross-certificate.
Indicates the
LOFD-003010 /
common name of NO NO Yes
TDLOFD-003010
the cross-certificate.
LOFD-003010 /
of the cross- NO NO Yes
TDLOFD-003010
certificate.
Indicates the
LOFD-003010 /
expiration date of NO NO Yes
TDLOFD-003010
Indicates the
LOFD-003010 /
loading status of NO NO Yes
TDLOFD-003010
Indicates the date

when the cross- LOFD-003010 /
NO NO Yes
take effect.
Indicates the file

name of the trusted
name cannot
include any of the
following
characters:
YES YES No
(:), asterisks (*),
question marks (?),
double quotation
brackets (<), right
angle brackets (>),
and bars (|).

LOFD-003010 /
number of the NO NO Yes
TDLOFD-003010
trusted certificate.
Indicates the
common name of LOFD-003010 /
NO NO Yes
the trusted TDLOFD-003010
certificate.
LOFD-003010 /
of the trusted NO NO Yes
TDLOFD-003010
certificate.
Indicates the
expiration date of LOFD-003010 /
NO NO Yes
certificate.
Indicates the
loading status of LOFD-003010 /
NO NO Yes
certificate.
Indicates the date

when the trusted LOFD-003010 /
NO NO Yes
take effect.
Indicates the file
name of a CRL.
The file name
cannot include any
of the following
characters:
backslashes (\),
LOFD-003010 /
slashes (/), colons YES YES No
TDLOFD-003010
(:), asterisks (*),
question marks (?),
double quotation
brackets (<), right
angle brackets (>),
and bars (|).
Indicates the
LOFD-003010 /
loading status of a NO NO Yes
TDLOFD-003010
CRL.
Indicates the issuer LOFD-003010 /

NO NO Yes
of a CRL. TDLOFD-003010
Indicates the next
LOFD-003010 /
update time of the NO NO Yes
TDLOFD-003010
CRL.
Indicates the
LOFD-003010 /
current update time NO NO Yes
TDLOFD-003010
of the CRL.
Indicates the IP
address of an FTP LOFD-003010 /
NO YES No
server or LDAP TDLOFD-003010
server.
Indicates the user

name used to log in LOFD-003010 /
NO NO No
to an FTP server or TDLOFD-003010
LDAP server.
Indicates the
password used to
LOFD-003010 /
log in to an FTP NO NO No
TDLOFD-003010
server or LDAP
server.
Indicates the port
LOFD-003010 /
number of an LDAP NO NO No
TDLOFD-003010
server.
Indicates the file

name of a CRL.
The file name
cannot include any
of the following
characters:
backslashes (\),
LOFD-003010 /
slashes (/), colons NO YES No
TDLOFD-003010
(:), asterisks (*),
question marks (?),
double quotation
brackets (<), right
angle brackets (>),
and bars (|).
Indicates whether
to update the CRL
at the next update
time specified in the
CRL that is
obtained during the
latest update. If this
parameter is set to
ENABLE, the BS
automatically
updates the CRL LOFD-003010 /
NO NO No
when the next TDLOFD-003010
update time
specified in the CRL
arrives. If this
parameter is set to
DISABLE, the BS
automatically
updates the CRL
based on the
configured updating
period.
Indicates the
BS automatically LOFD-003010 /
NO NO No
obtains the CRL TDLOFD-003010
from the FTP server
or LDAP server.
Indicates the ID of
the task for LOFD-003010 /
YES YES No
periodically TDLOFD-003010
obtaining the CRL.
Indicates the
method using which LOFD-003010 /
NO NO No
the BS periodically TDLOFD-003010
obtains a CRL.
Indicates the name

LOFD-003010 /
of a node found in NO NO No
TDLOFD-003010
an LDAP server.
Indicates the
source IP address
for downloading
CRLs. If this
parameter is set to
0.0.0.0, the BS
automatically uses NO NO No None
the OM IP address
of the main control
board as the source
IP to access the CA
and to update a
certificate.
Indicates whether a
task of certificate LOFD-003010 /
NO NO No
validity checking is TDLOFD-003010
started.
Indicates the
interval between LOFD-003010 /
NO NO No
certificate validity TDLOFD-003010
checking tasks.
Indicates the
threshold for
reporting a
certificate expiration
alarm. If a BS
detects that the
interval between its
LOFD-003010 /
current time and the NO NO No
TDLOFD-003010
expiration date of
an activated device
certificate is shorter
than the threshold,
a certificate
expiration alarm is
reported.
Indicates the
method for updating
a certificate that
has expired or is
about to expire.
There are two
methods: proxy and
CMP. If the proxy
method is used, the
LOFD-003010 /
BS uses the M2000 NO NO No
TDLOFD-003010
as the proxy to
update the
certificate from the
(CA). If the CMP
method is used, the
BS directly updates
the certificate from
the CA.

type. There are
three policies to use
CRLs. The value
NOVERIFY
indicates that the
BS does not
perform CRL-based
certificate checks.
The value ALARM
indicates that the
BS performs CRL-
based certificate
checks on the peer
device and reports
LOFD-003010 /
an alarm if the NO NO No
TDLOFD-003010
certificate is found
in the CRL. The
value
DISCONNECT
indicates that the
BS performs CRL-
based certificate
checks on the peer
device and cuts off
the communication
with the peer device
and reports an
alarm if the
certificate is found
in the CRL.
Indicates the ID of
the Access Control
List (ACL) to which
the access control
rule belongs. ACL
ID in the range from
3000 to 3999
LOFD-003009 /
identifies high-level
TDLOFD-003009
rules based on the YES YES No
LOFD-00301401 /
layer 3 and layer 4
TDLOFD-00301401
information. ACL ID
in the range from
4000 to 4999
identifies access
control rules based
on the MAC layer
information.
LOFD-003009 /
Indicates the brief
TDLOFD-003009
description of the NO YES No
LOFD-00301401 /
ACL.
TDLOFD-00301401
Indicates the ID of
the IPv6 Access LBFD-003006 /
Control List (ACL) TDLBFD-003006
YES YES No
to which the IPv6 LOFD-00301401 /
access control rule TDLOFD-00301401
belongs.
LBFD-003006 /
Indicates the brief
TDLBFD-003006
description of an NO YES No
LOFD-00301401 /
IPv6 ACL.
TDLOFD-00301401
Indicates the ID of
LOFD-003009 /
the Access Control
TDLOFD-003009
List (ACL) to which YES YES No
LOFD-00301401 /
the ACL rule
TDLOFD-00301401
belongs.
LOFD-003009 /
YES YES No
the ACL rule. LOFD-00301401 /
TDLOFD-00301401
Indicates the action
taken on the data
that matches the
ACL rule. When the
ACL to which the
ACL rule belongs is
referenced by a
packet filter, the BS
accepts or transmits
the data that
matches the rule if
this parameter is
set to PERMIT, and
rejects the data if
LOFD-003009 /
this parameter is
TDLOFD-003009
set to DENY. When NO NO No
LOFD-00301401 /
the ACL is
TDLOFD-00301401
referenced by an
IPSec policy, the
BS encrypts or
decrypts the data
that matches the
rule if this
parameter is set to
PERMIT, and does
not perform any
encryption or
decryption on the
data if this
parameter is set to
DENY.

protocol type of the TDLOFD-003009
NO YES No
data to which the LOFD-00301401 /
ACL rule is applied. TDLOFD-00301401
Indicates the
source IP address
of data to which the
ACL rule is applied. LOFD-003009 /
To add an ACL rule TDLOFD-003009
NO YES No
that is applicable to LOFD-00301401 /
data of all source IP TDLOFD-00301401
addresses, set this
parameter to
0.0.0.0.
Indicates the
wildcard of the
source IP address.
The wildcard is
used to determine
which bits can be LOFD-003009 /
neglected when IP TDLOFD-003009
NO YES No
address matching is LOFD-00301401 /
being performed. TDLOFD-00301401
Generally, it can be
considered as the
inverse of the
corresponding
subnet mask.
Indicates whether
to check the source LOFD-003009 /
port number of TDLOFD-003009
NO YES No
each data stream LOFD-00301401 /
before applying the TDLOFD-00301401
ACL rule.
set to OP_LT, the
ACL rule is applied
to the data stream
whose source port
number is smaller
configured port
number. If this
parameter is set to
OP_GT, the ACL
rule is applied to
the data stream
whose source port
number is larger
configured port
number. If this
LOFD-003009 /
parameter is set to
TDLOFD-003009
OP_EQ, the ACL NO YES No
LOFD-00301401 /
rule is applied to
TDLOFD-00301401
the data stream
whose source port
number is equal to
the configured port
number. If this
parameter is set to
OP_NEQ, the ACL
rule is applied to
the data stream
whose source port
number is not equal
to the configured
port number. If this
parameter is set to
OP_RANGE, the
ACL rule is applied
to the data stream
Indicates the
source port number
used when SMPT is
set to YES. If SOP
is set to
OP_RANGE, this LOFD-003009 /
parameter indicates TDLOFD-003009
NO YES No
the smallest source LOFD-00301401 /
port number. If SOP TDLOFD-00301401
is not set to
OP_RANGE, this
parameter indicates
a specific source
port number.
Indicates the
source port number
used when SMPT is
set to YES. If SOP
is set to LOFD-003009 /
OP_RANGE, this TDLOFD-003009
NO YES No
the largest source TDLOFD-00301401
port number. This
parameter is valid
only when SOP is
set to OP_RANGE.
Indicates the
destination IP
address of data to
which the ACL rule
LOFD-003009 /
is applied. To add
TDLOFD-003009
an ACL rule that is NO YES No
LOFD-00301401 /
applicable to data
TDLOFD-00301401
of all destination IP
addresses, set this
parameter to
0.0.0.0.
Indicates the
wildcard of the
destination IP
address. The
wildcard is used to
determine which
LOFD-003009 /
bits can be
TDLOFD-003009
neglected when IP NO YES No
LOFD-00301401 /
address matching is
TDLOFD-00301401
being performed.
Generally, it can be
considered as the
inverse of the
corresponding
subnet mask.
Indicates whether
to check the
LOFD-003009 /
destination port
TDLOFD-003009
number of each NO YES No
LOFD-00301401 /
data stream before
TDLOFD-00301401
applying the ACL
rule.
parameter is set to
OP_LT, the ACL
rule is applied to
the data stream
whose destination
port number is
smaller than or
equal to the
configured port
number. If this
parameter is set to
OP_GT, the ACL
rule is applied to
the data stream
whose destination
port number is
larger than or equal
to the configured LOFD-003009 /
port number. If this TDLOFD-003009
NO YES No
OP_EQ, the ACL TDLOFD-00301401
rule is applied to
the data stream
whose destination
port number is
equal to the
configured port
number. If this
parameter is set to
OP_NEQ, the ACL
rule is applied to
the data stream
whose destination
port number is not
equal to the
configured port
number. If this
parameter is set to
Indicates the
destination port
number used when
DMPT is set to
YES. If DOP is set
to OP_RANGE, this
the smallest TDLOFD-003009
NO YES No
destination port LOFD-00301401 /
number. If DOP is TDLOFD-00301401
not set to
OP_RANGE, this
parameter indicates
a specific
destination port
number.
Indicates the
destination port
number used when
DMPT is set to
YES. If DOP is set
LOFD-003009 /
to OP_RANGE, this
TDLOFD-003009
parameter indicates NO YES No
LOFD-00301401 /
the largest
TDLOFD-00301401
destination port
number. This
parameter is valid
only when DOP is
set to OP_RANGE.
Indicates whether
LOFD-003009 /
to check the DSCP
TDLOFD-003009
of each data stream NO NO No
LOFD-00301401 /
before applying the
TDLOFD-00301401
ACL rule.

Differentiated TDLOFD-003009
NO YES No
Services Code LOFD-00301401 /
Point (DSCP). TDLOFD-00301401
Indicates whether
to match the
fragment message.
The ACL rules for LOFD-003009 /
matching fragment TDLOFD-003009
NO NO No
messages apply to LOFD-00301401 /
only packet filtering TDLOFD-00301401
and does not apply
to the IPSec
function.
Indicates the filter

criteria for VLAN
IDs. This parameter
is valid only when
ACLID ranges from
4000 to 4999.
When this
parameter is set to
LOFD-003009 /
OP_EQ, only the
TDLOFD-003009
VLAN ID specified NO YES No
LOFD-00301401 /
by VLANID1 is a
TDLOFD-00301401
valid one. When
this parameter is
set to OP_RANGE,
all the VLAN IDs
within the range of
VLANID1 to
VLANID2 are valid
ones.
VLAN to which
service data
belongs. When
Source Port
Operate is set to
OP_EQ, this
LOFD-003009 /
parameter specifies
TDLOFD-003009
the ID of the NO YES No
LOFD-00301401 /
matching VLAN.
TDLOFD-00301401
When Source Port
Operate is set to
OP_RANGE, this
parameter specifies
the minimum ID of
the matching
VLANs.
VLAN to which
service data
belongs. When
Source Port
Operate is set to
LOFD-003009 /
OP_RANGE, this
TDLOFD-003009
parameter specifies NO YES No
LOFD-00301401 /
the maximum ID of
TDLOFD-00301401
the matching
VLANs. This
parameter is valid
only when Source
Port Operate is set
to OP_RANGE.
Indicates the ID of
the IPv6 Access LBFD-003006 /
Control List (ACL) TDLBFD-003006
YES YES No
to which the IPv6 LOFD-00301401 /
access control rule TDLOFD-00301401
belongs.
LBFD-003006 /
YES YES No
the IPv6 ACL rule. LOFD-00301401 /
TDLOFD-00301401
Indicates the action
taken on the data
that matches the
IPv6 ACL rule.
When the IPv6 ACL
is referenced by an
IPv6 IPSec policy,
the BS encrypts or
LBFD-003006 /
decrypts the data
TDLBFD-003006
that matches the NO NO No
LOFD-00301401 /
rule if this
TDLOFD-00301401
parameter is set to
PERMIT, and does
not perform any
encryption or
decryption on the
data if this
parameter is set to
DENY.
Indicates the
LBFD-003006 /
protocol type of the
TDLBFD-003006
data to which the NO YES No
LOFD-00301401 /
IPv6 ACL rule is
TDLOFD-00301401
applied.
Indicates the
LBFD-003006 /
source IPv6
TDLBFD-003006
address of data to NO YES No
LOFD-00301401 /
which the IPv6 ACL
TDLOFD-00301401
rule is applied.
Indicates the prefix
length of the source
IPv6 address. The
prefix length is used
LBFD-003006 /
to determine which
TDLBFD-003006
bits must be NO YES No
LOFD-00301401 /
compared for
TDLOFD-00301401
matching when
IPv6 address
matching is being
performed.
Indicates whether
to check the source LBFD-003006 /
port number of TDLBFD-003006
NO YES No
each data stream LOFD-00301401 /
before applying the TDLOFD-00301401
ACL rule.
OP_LT, the ACL
rule is applied to
the data stream
whose source port
number is smaller
configured port
number. If this
parameter is set to
OP_GT, the ACL
rule is applied to
the data stream
whose source port
number is larger
configured port
number. If this
LBFD-003006 /
parameter is set to
TDLBFD-003006
OP_EQ, the ACL NO YES No
LOFD-00301401 /
rule is applied to
TDLOFD-00301401
the data stream
whose source port
number is equal to
the configured port
number. If this
parameter is set to
OP_NEQ, the ACL
rule is applied to
the data stream
whose source port
number is not equal
to the configured
port number. If this
parameter is set to
OP_RANGE, the
ACL rule is applied
to the data stream
Indicates the
source port number
used when SMPT is
set to YES. If SOP
is set to
OP_RANGE, this LBFD-003006 /
parameter indicates TDLBFD-003006
NO YES No
the smallest source LOFD-00301401 /
port number. If SOP TDLOFD-00301401
is not set to
OP_RANGE, this
parameter indicates
a specific source
port number.
Indicates the
source port number
used when SMPT is
set to YES. If SOP
is set to LBFD-003006 /
OP_RANGE, this TDLBFD-003006
NO YES No
the largest source TDLOFD-00301401
port number. This
parameter is valid
only when SOP is
set to OP_RANGE.
Indicates the
LBFD-003006 /
destination IPv6
TDLBFD-003006
address of data to NO YES No
LOFD-00301401 /
which the IPv6 ACL
TDLOFD-00301401
rule is applied.
length of the
destination IPv6
address. The prefix
length is used to LBFD-003006 /
determine which TDLBFD-003006
NO YES No
bits must be LOFD-00301401 /
compared for TDLOFD-00301401
matching when
IPv6 address
matching is being
performed.
Indicates whether
to check the
LBFD-003006 /
destination port
TDLBFD-003006
number of each NO YES No
LOFD-00301401 /
data stream before
TDLOFD-00301401
applying the ACL
rule.
parameter is set to
OP_LT, the ACL
rule is applied to
the data stream
whose destination
port number is
smaller than or
equal to the
configured port
number. If this
parameter is set to
OP_GT, the ACL
rule is applied to
the data stream
whose destination
port number is
larger than or equal
to the configured LBFD-003006 /
port number. If this TDLBFD-003006
NO YES No
OP_EQ, the ACL TDLOFD-00301401
rule is applied to
the data stream
whose destination
port number is
equal to the
configured port
number. If this
parameter is set to
OP_NEQ, the ACL
rule is applied to
the data stream
whose destination
port number is not
equal to the
configured port
number. If this
parameter is set to
Indicates the
destination port
number used when
DMPT is set to
YES. If DOP is set
to OP_RANGE, this
parameter indicates LBFD-003006 /
the smallest TDLBFD-003006
NO YES No
number. If DOP is TDLOFD-00301401
not set to
OP_RANGE, this
parameter indicates
a specific
destination port
number.
Indicates the
destination port
number used when
DMPT is set to
YES. If DOP is set
LBFD-003006 /
to OP_RANGE, this
TDLBFD-003006
parameter indicates NO YES No
LOFD-00301401 /
the largest
TDLOFD-00301401
destination port
number. This
parameter is valid
only when DOP is
set to OP_RANGE.
Indicates whether
LBFD-003006 /
to check the DSCP
TDLBFD-003006
of each data stream NO NO No
LOFD-00301401 /
before applying the
TDLOFD-00301401
IPv6 ACL rule.
LBFD-003006 /
Indicates the DSCP
TDLBFD-003006
that complies with NO YES No
LOFD-00301401 /
an IPv6 ACL rule.
TDLOFD-00301401
Indicates the
cabinet No. to LOFD-003007 /
YES NO No
which a BFD TDLOFD-003007
session belongs.
Indicates the
subrack No. to LOFD-003007 /
YES NO No
which a BFD TDLOFD-003007
session belongs.
Indicates the slot

LOFD-003007 /
No. to which a BFD YES YES No
TDLOFD-003007
session belongs.
BFD session. The
session ID plus 1 is
the local
discriminator of the
LOFD-003007 /
BFD session. The YES YES No
TDLOFD-003007
local discriminator
must be consistent
with the
configuration at the
peer side.
Indicates the
source IP address
of the BFD session.
The source IP
address of a BFD
session must be a
device IP address
(for example, the IP
address of an
Ethernet port) of a
specified board or a
logical IP address
(for example, the IP
address of the
LOFD-003007 /
loopback port), but NO YES No
TDLOFD-003007
IP address of a
remote
maintenance
channel or a
negotiated IP
address. Note that
a BFD session
cannot be
configured as a
single-hope session
if its source IP
address is a logical
IP address.
Indicates the
destination IP
address of a BFD
session. The
destination IP
address must be a
valid IP address,
and cannot be set
to 0.0.0.0 or any
existing IP
addresses in the
system. If Virtual
LOFD-003007 /
Router Redundancy NO YES No
TDLOFD-003007
Protocol (VRRP) is
used in the
network, two BFD
sessions must be
configured with the
destination IP
addresses set to
the active and
standby physical IP
addresses of the
virtual router,
respectively.
Indicates the hop
type of the BFD
session. The single-
hop BFD session is
used to perform
point-to-point
detection at the
data link layer, and
often used in layer
2 networking LOFD-003007 /
NO YES No
scenarios. The TDLOFD-003007
multi-hop BFD
session is used to
perform end-to-end
connectivity checks
at the transport
layer, and often
used in layer 3
networking
scenarios.
Indicates the
minimum interval at
LOFD-003007 /
which the BFD NO NO No
TDLOFD-003007
session transmits
control packets.
Indicates the
minimum interval at
LOFD-003007 /
which the BFD NO NO No
TDLOFD-003007
session receives
control packets.
Indicates the
LOFD-003007 /
detection multiplier NO NO No
TDLOFD-003007
of a BFD session.
Indicates the type
of the BFD session.
set to
MAINTENANCE,
this BFD session is
used only for
continuity check
(CC). If this
parameter is set to
RELIABILITY, the
BFD session is LOFD-003007 /
NO NO No
used to trigger TDLOFD-003007
route interlock.
Route interlock
enables the
standby route to
take over once the
active route
becomes faulty, and
therefore prevents
service interruption
caused by route
failures.
Indicates the
Differentiated
Services Code
Point (DSCP). The LOFD-003007 /
NO NO No
priority has a TDLOFD-003007
with the value of
this parameter.
Indicates whether
to delete the
historical statistics.
set to YES, the
historical statistics LOFD-003007 /
NO NO Yes
are deleted and a TDLOFD-003007
new round of
statistics collecting
starts upon
completion of the
query.
Indicates the state LOFD-003007 /

NO NO Yes
of a BFD session. TDLOFD-003007
Indicates the
effective detection LOFD-003007 /
NO NO Yes
mode through TDLOFD-003007
negotiation.
Indicates the
effective minimum LOFD-003007 /
NO NO Yes
TX interval through TDLOFD-003007
negotiation.
Indicates the
effective minimum LOFD-003007 /
NO NO Yes
RX interval through TDLOFD-003007
negotiation.
Indicates the
detection time when LOFD-003007 /
NO NO Yes
the negotiation TDLOFD-003007
takes effect.
Indicates the local
discriminator of the
BFD session. The
LOFD-003007 /
value of this NO NO Yes
TDLOFD-003007
parameter is equal
to the session
number plus 1.
Indicates the peer
LOFD-003007 /
descriminator of a NO NO Yes
TDLOFD-003007
BFD session.
Indicates the
NO NO Yes
transmitted packets TDLOFD-003007
of a BFD session.
Indicates the
number of
LOFD-003007 /
messages received NO NO Yes
TDLOFD-003007
by the BFD
session.
Indicates the up-to-
LOFD-003007 /
down number of a NO NO Yes
TDLOFD-003007
BFD session.
Indicates the
diagnostic field of
LOFD-003007 /
the BFD session, NO NO Yes
TDLOFD-003007
that is, the cause of
the latest failure.
Indicates the
LOFD-003007 /
protocol version of NO NO No
TDLOFD-003007
a BFD session.
Indicates the
deployment position
of a digital
certificate. If this
parameter is set to
DEFAULT, the
certificate is
LOFD-003010 /
configured on the NO NO No
TDLOFD-003010
main control board.
set to SPECIFIC,
the certificate is
configured on the
board in the
specified slot.
Indicates the
NO NO No
cabinet where a TDLOFD-003010
board is located.
Indicates the
NO NO No
subrack where a TDLOFD-003010
board is located.
Indicates the
number of the slot LOFD-003010 /
NO NO No
where a board is TDLOFD-003010
located.
Indicates the name

LOFD-00300402 /
of the MD to which YES YES No
TDLOFD-00300402
the RMEP belongs.
Indicates the name

LOFD-00300402 /
of the MA to which YES YES No
TDLOFD-00300402
the RMEP belongs.
Indicates the RMEP LOFD-00300402 /

YES YES No
ID. TDLOFD-00300402
cannot be the same
as the existing local
IP address or any
IP address of an
effective physical or
loopback port. The
bound IP address
cannot be the same
as the local IP
address
dynamically
negotiated on the
PPP/MLPPP link.
When the IP
address is bound,
the existing IP
address of the
system may conflict
with the IP address LOFD-00300402 /
YES YES No
to be configured, TDLOFD-00300402
run the LST/DSP
(DEVIP, OMCH,
PPPLNK, LOCALIP,
MPGRP, or IPRT)
command to query
the IP address of
the system (such as
device IP address,
local IP address of
the remote
maintenance
channel, local IP
address of the PPP
link, IP address of
the local
maintenance
channel, local IP
address of the
Indicates the name

LOFD-00300402 /
TDLOFD-00300402
the MA belongs.

YES YES No
of the MA. TDLOFD-00300402
Indicates cabinet
NO NO No
board to which the TDLOFD-00300402
MA belongs.
Indicates subrack
NO NO No
MA belongs.
Indicates slot
NO YES No
MA belongs.
Indicates whether
the MA is LOFD-00300402 /
NO NO No
associated with the TDLOFD-00300402
VLAN.
Indicates the ID of
the VLAN with LOFD-00300402 /
NO NO No
which the MA is TDLOFD-00300402
associated.
Indicates the
priority of the VLAN LOFD-00300402 /
NO NO No
with which the MA TDLOFD-00300402
is associated.
Indicates the
LOFD-00300402 /
CFM MA transmits NO NO No
TDLOFD-00300402
continuity check
messages (CCMs).
Indicates the
LOFD-00300402 /
number of local NO NO Yes
TDLOFD-00300402
MEPs in an MA.
Indicates the
LOFD-00300402 /
number of RMEPs NO NO Yes
TDLOFD-00300402
in an MA.
Indicates the list of
LOFD-00300402 /
local MEPs in an NO NO Yes
TDLOFD-00300402
MA.
Indicates the list of LOFD-00300402 /
NO NO Yes
RMEPs in an MA. TDLOFD-00300402

YES YES No
of the CFM MD. TDLOFD-00300402
Indicates the level LOFD-00300402 /
NO NO No
of the CFM MD. TDLOFD-00300402
Indicates the
LOFD-00300402 /
number of MAs in a NO NO Yes
TDLOFD-00300402
CFMMD.
LOFD-00300402 /
all MAs in a NO NO Yes
TDLOFD-00300402
CFMMD.
Indicates the name

LOFD-00300402 /
TDLOFD-00300402
the MEP belongs.
Indicates the name

LOFD-00300402 /
TDLOFD-00300402
the MEP belongs.
Indicates the MEP LOFD-00300402 /

YES YES No
ID. TDLOFD-00300402
Indicates cabinet
NO NO No
MEP belongs.
Indicates subrack
NO NO No
MEP belongs.
Indicates slot
NO YES No
MEP belongs.
Indicates the type
of subboard on the LOFD-00300402 /
NO YES No
board where the TDLOFD-00300402
MEP is located.
Indicates the port LOFD-00300402 /

NO YES No
type of MEP. TDLOFD-00300402

NO YES No
number of the MEP. TDLOFD-00300402
Indicates whether
to enable the LOFD-00300402 /
NO NO No
continuity check TDLOFD-00300402
(CC) of the CFM.
VLAN of the MA to LOFD-00300402 /
NO NO Yes
which the MEP TDLOFD-00300402
belongs.
NO NO Yes
which the MEP TDLOFD-00300402
belongs.
Indicates the
priority of a VLAN LOFD-00300402 /
NO NO Yes
of the MA to which TDLOFD-00300402
the MEP belongs.
Indicates the
number of
LOFD-00300402 /
transmitted NO NO Yes
TDLOFD-00300402
Connectivity Check
(CC) packets.
Indicates the
number of received LOFD-00300402 /
NO NO Yes
Connectivity Check TDLOFD-00300402
(CC) packets.
Indicates the
NO NO Yes
transmitted TDLOFD-00300402
loopback packets.
Indicates the
LOFD-00300402 /
number of received NO NO Yes
TDLOFD-00300402
loopback packets.
Indicates the
NO NO Yes
transmitted traced TDLOFD-00300402
over packets.
Indicates the
NO NO Yes
traced over TDLOFD-00300402
packets.
Indicates the
NO NO Yes
CFM packets.
Indicates the
NO NO Yes
CFM packets.
Indicates the
number of
LOFD-00300402 /
transmitted packets NO NO Yes
TDLOFD-00300402
CFM packets
discarded.
Indicates the
NO NO Yes
packets CFM TDLOFD-00300402
packets discarded.
Indicates the name

LOFD-00300402 /
TDLOFD-00300402
the RMEP belongs.
Indicates the name
LOFD-00300402 /
TDLOFD-00300402
the RMEP belongs.
Indicates the RMEP LOFD-00300402 /

YES YES No
ID. TDLOFD-00300402
Indicates the MAC

address of the
RMEP. It must be a
valid unicast
address in the
format of XXXX-
XXXX-XXXX. The
MAC address of the
RMEP can be
obtained from the
LOFD-00300402 /
MAC address field NO NO No
TDLOFD-00300402
carried in the CCM
message. If the
MAC address
configured by the
user is different
from that carried in
the CCM message,
the MAC address
carried in the MAC
message prevails.
Indicates the status LOFD-00300402 /

NO NO Yes
of the RMEP. TDLOFD-00300402
MAC address of the
LOFD-00300402 /
RMEP. The format NO NO Yes
TDLOFD-00300402
is XXXX-XXXX-
XXXX.
Indicates the
priority of a VLAN LOFD-00300402 /
NO NO Yes
of the MA to which TDLOFD-00300402
the RMEP belongs.
NO NO Yes
which the RMEP TDLOFD-00300402
belongs.
Indicates the
NO NO Yes
CCM packets from TDLOFD-00300402
the RMEP.
Indicates the
number of the IP LOFD-00300402 /
NO NO Yes
addresses bound to TDLOFD-00300402
the RMEP.
LOFD-00300402 /
the IP addresses NO NO Yes
TDLOFD-00300402
bound to the RMEP.
Indicates the type

of the LOFD-003014 /
YES YES No
commissioning TDLOFD-003014
service.
Indicates the
LOFD-003014 /
number of the YES YES No
TDLOFD-003014
commissioning port.
used to enable or
disable the
commissioning port
to run
commissioning
services. This port
is physically located
at the local
maintenance
Ethernet port. If this
parameter is set to
DISABLE, the
commissioning port
cannot run
LOFD-003014 /
commissioning NO YES No
TDLOFD-003014
services. If this
parameter is set to
ENABLE, the
commissioning port
can run
commissioning
services. In this
situation, this
commissioning port
receives cyber
attacks, therefore
special caution
must be exercised
during the setting of
this parameter.
Indicates the
cabinet number of
YES NO No None
the board where the
port is located.
Indicates the
subrack number of
YES NO No None
the board where the
port is located.
Indicates the slot
number of the
YES YES No None
board where the
port is located.
Indicates the type
of sub-board on the
YES YES No None
board where a port
is located.
Indicates the port

YES YES No None
type.
Indicates the
YES YES No None
number of a port.
Indicates the IP
address configured YES YES No None
for the port.
Indicates the
subnet mask of the
device IP address NO YES No None
configured on the
port.
Indicates the
interface index of LBFD-003006 /
YES YES No
the device IPv6 TDLBFD-003006
address.

YES YES No None
IPv6 address.

of the prefix of the LBFD-003006 /
NO YES No
device IPv6 TDLBFD-003006
address.

LBFD-003006 /
of the device IPv6 NO NO Yes
TDLBFD-003006
address.
Indicates the time

interval during
LBFD-003006 /
which the device NO NO Yes
TDLBFD-003006
IPv6 address is in
the valid state.
Indicates the time
interval during
which the device
IPv6 address is in
the preferred state.
Valid states are
categorized into the
preferred state and
the deprecated
state. In the
preferred state, an
LBFD-003006 /
address can be NO NO Yes
TDLBFD-003006
freely used; in the
deprecated state,
the connections
previously
established on this
address are still
usable, whereas
any connection
newly established
on this address is
not usable.
Indicates whether
to enable the DHCP NO NO No None
relay switch.
LBFD-00300102 /
TDLBFD-00300102
Indicates the IP
LBFD-00300103 /
address of the YES YES No
TDLBFD-00300103
DHCP server.
LOFD-002004 /
TDLOFD-002004
Indicates whether
to enable detection
of automatic
LOFD-002004 /
establishment of NO NO No
TDLOFD-002004
the remote
maintenance
channel.
Indicates the rule
for prioritizing traffic
to meet service
requirements. If this
parameter is set to
IPPRECEDENCE,
the protocol stack LBFD-00300201 /
NO NO No
of the earlier TDLBFD-00300201
version is adopted,
which firstly
converts types of
service (TOSs) to
DSCPs and then
prioritizes traffic.
Indicates the
priority of signaling.
The priority has a LBFD-00300201 /
NO NO No
positive correlation TDLBFD-00300201
with the value of
this parameter.
Indicates the
priority of the high-
level OM data. The
priority has a
with the value of
this parameter. The LBFD-00300201 /
NO NO No
high-level OM data TDLBFD-00300201
includes the
packets related to
remote
maintenance
channel switchover
and DHCP relay.
Indicates the
priority of the low-
level OM data, such
as the data to be
uploaded or
downloaded. The
priority has a
LBFD-00300201 /
positive correlation NO NO No
TDLBFD-00300201
with the value of
this parameter. The
low-level OM data
includes the
packets related to
File Transfer
Protocol (FTP).
Indicates the DSCP

of the IP clock
packet. If the clock
that follows the
Precision Time
Protocol (PTP) is
used, the DSCP of
LBFD-00300201 /
the PTP packets NO NO No
TDLBFD-00300201
takes effect. If the
clock that follows
the Huawei
proprietary protocol
is used, the DSCP
of the protocol
packet takes effect.
Indicates the
priority of user data
type 1. The priority
LBFD-00300201 /
has a positive NO NO No
TDLBFD-00300201
value of this
parameter.
Indicates the type

of primary transport LBFD-00300201 /
NO NO No
resource for user TDLBFD-00300201
data type 1.
Indicates the
primary port load
threshold of user
data type 1. This
threshold equals LBFD-00300201 /
NO NO No
the ratio of the TDLBFD-00300201
bandwidth occupied
by the type-1 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 1. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
by the type-1 data LBFD-00300201 /
NO NO No
to the secondary- TDLBFD-00300201
port bandwidth
occupied by the
type-1 data. When
this threshold is
exceeded, the type-
1 data is
preferentially
admitted through
the port with a light
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 2.
Indicates the
primary port load
threshold of user
data type 2. This
NO NO No
bandwidth occupied
by the type-2 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 2. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-2 data. When
this threshold is
exceeded, the type-
2 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 3.
Indicates the
primary port load
threshold of user
data type 3. This
NO NO No
bandwidth occupied
by the type-3 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 3. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-3 data. When
this threshold is
exceeded, the type-
3 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 4.
Indicates the
primary port load
threshold of user
data type 4. This
NO NO No
bandwidth occupied
by the type-4 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 4. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-4 data. When
this threshold is
exceeded, the type-
4 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 5.
Indicates the
primary port load
threshold of user
data type 5. This
NO NO No
bandwidth occupied
by the type-5 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 5. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-5 data. When
this threshold is
exceeded, the type-
5 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 6.
Indicates the
primary port load
threshold of user
data type 6. This
NO NO No
bandwidth occupied
by the type-6 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 6. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-6 data. When
this threshold is
exceeded, the type-
6 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 7.
Indicates the
primary port load
threshold of user
data type 7. This
NO NO No
bandwidth occupied
by the type-7 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 7. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-7 data. When
this threshold is
exceeded, the type-
7 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 8.
Indicates the
primary port load
threshold of user
data type 8. This
NO NO No
bandwidth occupied
by the type-8 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 8. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-8 data. When
this threshold is
exceeded, the type-
8 data is
preferentially
admitted through
load.
Indicates the
LBFD-00300201 /
TDLBFD-00300201
value of this
parameter.
Indicates the type

NO NO No
data type 9.
Indicates the
primary port load
threshold of user
data type 9. This
NO NO No
bandwidth occupied
by the type-9 data
to the total port
bandwidth.
Indicates the
threshold of the
primary-to-
secondary port load
ratio of user data
type 9. This
threshold equals
the ratio of the
primary-port
bandwidth occupied
NO NO No
port bandwidth
occupied by the
type-9 data. When
this threshold is
exceeded, the type-
9 data is
preferentially
admitted through
load.
This parameter
indicates whether to
limit S1 interface
downlink rate
measured in bit per
second (bps) in
case of LBBP CPU
overload. When S1
interface downlink
traffic volume
NO NO No None
exceeds LBBP
process ability, CPU
in LBBP will
overload and it will
lead to degradation
of air interface. This
switch can be
turned on to limit S1
interface downlink
rate.
This parameter
indicates whether to
limit S1 interface
downlink rate
measured in packet
per second (pps) in
case of LBBP CPU
overload. When S1
interface downlink
traffic volume
NO NO No None
exceeds LBBP
process ability, CPU
in LBBP will
overload and it will
lead to degradation
of air interface. This
switch can be
turned on to limit S1
interface downlink
rate.
Indicates the
number of the
cabinet that
provides the port on YES NO No None
which IEEE 802.1X
authentication is
configured.
Indicates the
number of the
subrack that
provides the port on YES NO No None
which IEEE 802.1X
authentication is
configured.
Indicates the
number of the slot
that provides the
port on which IEEE YES YES No None
802.1X
authentication is
configured.
Indicates the type

of sub-board that
provides the port on
YES YES No None
which IEEE 802.1X
authentication is
configured.
Indicates the
number of the port
on which IEEE LOFD-003015 /
YES YES No
802.1X TDLOFD-003015
authentication is
configured.
Indicates the IEEE

802.1X
authentication
method. Currently,
only Extensible
Authentication
LOFD-003015 /
Protocol Transport NO NO No
TDLOFD-003015
Layer Security
(EAP-TLS), a
unidirectional
authentication
method, is
supported.
Indicates the
number of
abnormal packets LOFD-003015 /
NO NO Yes
received during the TDLOFD-003015
802.1X
authentication.
Indicates the
number of IEEE
LOFD-003015 /
802.1X NO NO Yes
TDLOFD-003015
authentication
failures.
Indicates the cause

of the latest IEEE
802.1X
authentication
failure or the latest
unauthentication
where the BS does
LOFD-003015 /
not initiate the NO NO Yes
TDLOFD-003015
authentication. The
value of this
parameter is
deleted after a
successful IEEE
802.1X
authentication.
Indicates the
number of received
Extensible LOFD-003015 /
NO NO Yes
Authentication TDLOFD-003015
Protocol (EAP)
messages.
of IEEE 802.1X
authentication.
Possible states are
as follows:
UNAUTHENTICAT
ED(Unauthenticate
d),
AUTHENTICATING
(Authenticating), LOFD-003015 /
NO NO Yes
AUTHENTIC_SUC TDLOFD-003015
CEED(Authenticate
Succeed),
AUTHENTIC_FAIL(
Authenticate Fail),
and
DHCP_AUTHENTI
CATING(DHCP
Activation
Authenticating).
Indicates the
number of
transmitted
LOFD-003015 /
Extensible NO NO Yes
TDLOFD-003015
Authentication
Protocol (EAP)
messages.
Indicates the
number of
LOFD-003015 /
successful IEEE NO NO Yes
TDLOFD-003015
802.1X
authentications.
Indicates the
priority of a DSCP.
A larger value of LBFD-00300201 /
YES YES No
this parameter TDLBFD-00300201
indicates a higher
priority.
Indicates the
priority of a VLAN. A
LBFD-003003 /
larger value of this NO YES No
TDLBFD-003003
parameter indicates
a higher priority.
Indicates the
number of the
cabinet housing the
YES NO No None
board where an
E1/T1 port is
located.
Indicates the
number of the
subrack housing
YES NO No None
the board where the
E1/T1 port is
located.
Indicates the
number of the slot
housing the board YES YES No None
where the E1/T1
port is located.
Indicates the
number of the YES NO No None
E1/T1 port.
Indicates the range

of E1/T1 ports.
Note that the E1T1
MO with this
NO NO No None
parameter set to
ALLPORT is
actually not created
on the BS.
Indicates the
working mode of
the E1/T1 port. This
parameter must be NO NO No None
set to the same
value as that at the
peer end.
Indicates the frame
format used by the NO YES No None
E1/T1 port.
Indicates the line
coding mode of an NO YES No None
E1/T1 port.
Indicates the clock
mode of the E1/T1
port.
1. If the BS extracts
the line clock from
the E1/T1 port, the
clock mode of the
E1/T1 port must be
set to SLAVE. If the
BS provides the line
clock for the lower-
level equipment
through the E1/T1
port, the clock
mode of the E1/T1
port must be set to
MASTER.
NO NO No None
Otherwise, the line
clock may fail to
work properly.
2. When the E1/T1
port provides an 8K
clock reference for
the transmission
interface board, the
clock mode of the
E1/T1 port must be
set to SLAVE.
3. The clock modes
of E1/T1 ports used
by an inter-board
MLPPP group
cannot be all set to
SLAVE.
Indicates the link
running status. The
link running status
is classified into
OK, LOCAL_LOOP,
REMOTE_LOOP,
PAYLOAD_LOOP,
NO NO Yes None
SINGLE_CH_LOOP
,
PHYSICAL_LOOP,
LOS, AIS, RA, LFA,
LMFA, SLIP,
BACKUP, and
OTHERS.
Indicates whether
to perform the link
test and the test
type. The test types
NO NO Yes None
are classified into
No Test, Offline
Test, and Online
Test.
Indicates whether
the E1/T1 port is NO NO Yes None
used.
Indicates the left
loop time of the NO NO Yes None
E1/T1 port.
Indicates the type

of sub-board on the
board where the YES YES No None
E1/T1 port is
located.
Indicates the in-use
work mode of the NO NO Yes None
E1/T1 port.

frame format of the NO NO Yes None
E1/T1 port.

line coding mode of NO NO Yes None
the E1/T1 port.
Indicates the BER

NO NO No None
threshold.
Indicates the
cabinet number of
LOFD-00300401 /
the board where the YES NO No
TDLOFD-00300401
Ethernet port is
located.
Indicates the
subrack number of
LOFD-00300401 /
TDLOFD-00300401
Ethernet port is
located.
Indicates the slot
number of the
LOFD-00300401 /
board where the YES YES No
TDLOFD-00300401
Ethernet port is
located.
Indicates the type
of sub-board on the
LOFD-00300401 /
TDLOFD-00300401
Ethernet port is
located.

YES YES No
of the Ethernet port. TDLOFD-00300401
Indicates the
LOFD-00300401 /
TDLOFD-00300401
Ethernet port.
Indicates the work

mode of the
IEEE802.3ah
Ethernet OAM.
set to ACTIVE, the
local end initiates
the IEEE802.3ah
Ethernet OAM
negotiation. LOFD-00300401 /
NO NO No
If this parameter is TDLOFD-00300401
set to PASSIVE, the
local end does not
initiate the
negotiation;
instead, the local
end waits for
receiving
negotiation packets
from the peer end.
Indicates the
internal at which a
Protocol Data Unit
(PDU) is
transmitted for fault
LOFD-00300401 /
detection. A shorter NO NO No
TDLOFD-00300401
interval indicates
that Ethernet link
faults can be
detected more
quickly.
LOFD-00300401 /
the Protocol Data NO NO No
TDLOFD-00300401
Unit (PDU).
Indicates whether
remote loopback
can be enabled at
the port where 3AH
detection is
activated. If remote
loopback is
enabled, the OAM
3AH loopback is
see the STR LOFD-00300401 /
NO NO No
ETHOAMLOOPTST TDLOFD-00300401
command. During
the loopback, only
3AH packets rather
than other types of
packet can be
transmitted. If
remote loopback is
disabled, the local
end cannot initiate
the loopback.
Indicates whether
LOFD-00300401 /
to enable indication NO NO No
TDLOFD-00300401
of link faults.
Indicates the
duration of the LOFD-00300401 /
NO NO No
erroneous frame TDLOFD-00300401
event.
Indicates the
threshold for the
erroneous frame
event. If the number
of erroneous
frames within a LOFD-00300401 /
NO NO No
second exceeds the TDLOFD-00300401
threshold, an
erroneous frame
event occurs. This
event is checked
every other second.
Indicates the
duration of the Error
Frame Seconds
Summary Event. An
LOFD-00300401 /
error frame second NO NO No
TDLOFD-00300401
refers to a second
within which one or
more error frames
are detected.
Indicates the
threshold for the
accumulated
erroneous frame
event. If the length
of time that
erroneous frames
occupy within a
sampling period LOFD-00300401 /
NO NO No
specified through TDLOFD-00300401
the
ERRFRMSCDEVT
PRD parameter
exceeds the
threshold, an
accumulated
erroneous frame
event occurs.
Indicates the Finite

State Machine LOFD-00300401 /
NO NO Yes
(FSM) status of an TDLOFD-00300401
Ethernet OAM 3AH.
Indicates the
number of
LOFD-00300401 /
discarded OAM NO NO Yes
TDLOFD-00300401
PDUs on the RX
channel.
Indicates the
LOFD-00300401 /
TDLOFD-00300401
Event OAM PDUs.
Indicates the
LOFD-00300401 /
TDLOFD-00300401
Fault OAM PDUs.
Indicates the
number of Info LOFD-00300401 /
NO NO Yes
OAM PDUs TDLOFD-00300401
received on a port.
Indicates the
NO NO Yes
Loopback Control TDLOFD-00300401
OAM PDUs.
Indicates the total

number of received
OAM PDUs,
including the
information OAM LOFD-00300401 /
NO NO Yes
PDUs, event OAM TDLOFD-00300401
PDUs, loopback
OAM PDUs, and
discarded OAM
PDUs.
Indicates the
number of
LOFD-00300401 /
discarded OAM NO NO Yes
TDLOFD-00300401
PDUs on the TX
channel.
Indicates the
number of
transmitted Event
OAM PDUs. The LOFD-00300401 /
NO NO Yes
Event OAM PDUs TDLOFD-00300401
are used to notify
the peer end of a
link event.
Indicates the
number of
transmitted Fault
OAM PDUs. The LOFD-00300401 /
NO NO Yes
Fault OAM PDUs TDLOFD-00300401
are used to notify
the peer end of a
link failure.
Indicates the
number of
transmitted Info
OAM Protocol Data LOFD-00300401 /
NO NO Yes
Units (PDUs). The TDLOFD-00300401
Info OAM PDUs are
used to finish the
search process.
Indicates the
number of
transmitted
loopback OAM
LOFD-00300401 /
PDUs. The NO NO Yes
TDLOFD-00300401
loopback OAM
PDUs are used for
remote loopback
control.
Indicates the total
number of
transmitted OAM
PDUs, including the
information OAM LOFD-00300401 /
NO NO Yes
PDUs, event OAM TDLOFD-00300401
PDUs, loopback
OAM PDUs, and
discarded OAM
PDUs.
Indicates the
cabinet number of
Ethernet port is
located.
Indicates the
subrack number of
Ethernet port is
located.
Indicates the slot

number of the
Ethernet port is
located.
Indicates the type

of sub-board on the
Ethernet port is
located.
Indicates the
Ethernet port.
Indicates whether
an Ethernet port is
an electrical port or
optical port. When
the system starts,
the system binds an
Ethernet port to an
optical port
NO YES No None
preferentially if the
default value of the
port attribute is
AUTO. If the BS
does not support
cascading, the port
attribute is set to
AUTO.
Indicates the
maximum
transmission unit
(MTU) for the
Ethernet port. It
specifies the
maximum size of
the IP packet
(including the IP
header) that can
flow through the
Ethernet port. A
value equal to or
larger than 776 is
recommended,
because broadcast
packets, such as
NO NO No None
the DHCP packet,
may experience
reception or
transmission
failures if the MTU
is smaller than 776.
After the Ethernet
port is added to an
Ethernet trunk, this
parameter stops
taking effect and
the actual MTU for
the Ethernet port
depends on the
setting of the same
parameter in the
Ethernet trunk.
Indicates the speed
mode of the
Ethernet port. This
parameter must be
set to the same
value as that of the
peer port. GE
electrical ports of
base board support
1000 Mbit/s only
when working in
auto-negotiation
NO NO No None
mode. If SPEED of
a GE optical port is
set to AUTO, the
port works at 1000
Mbit/s in auto-
negotiation mode. If
SPEED of a GE
optical port is set to
1000M, the port
works at 1000
Mbit/s in manual
configuration mode.

mode of the NO NO No None
Ethernet port.
Indicates whether
to enable the proxy
ARP function. If this
function is enabled,
the BS serves as
an ARP proxy for
the IP address of a
loopback interface
on the BS or a port
IP address of a
lower-level BS. If
this function is
disabled, an
external device can
access a loopback
interface in the BS
or a lower-level BS NO NO No None
on the same subnet
only by using a
route. After the
Ethernet port is
added to an
Ethernet trunk, this
parameter stops
taking effect and
whether the proxy
ARP function is
enabled for the
Ethernet port
depends on the
setting of the same
parameter in the
Ethernet trunk.
Indicates whether
to enable flow
control on the
Ethernet port. Flow
control is
implemented to
prevent congestion.
When flow control is
enabled, the RX
end repeatedly
sends PAUSE
frames to the TX
end, instructing the NO NO No None
TX end to lower the
TX rate if
congestion occurs
on the RX end.
Upon receiving
PAUSE frames, the
TX end stops
sending data during
a period of time to
prevent congestion.
For details, see
IEEE 802.3ah.
Indicates the
generation
threshold for the
MAC Excessive
Frame Error Rate
alarm (ID: 25881).
When the number NO NO No None
of erroneous MAC
frames exceeds this
threshold, the MAC
Excessive Frame
Error Rate alarm is
reported.
Indicates the
clearance threshold
for the MAC
Excessive Frame
Error Rate alarm
(ID: 25881). When
the number of NO NO No None
erroneous MAC
frames falls below
this threshold, the
MAC Excessive
Frame Error Rate
alarm is cleared.
Indicates the MAC
address (six bytes)
configured for the
NO NO Yes None
Ethernet port. The
format is XXXX-
XXXX-XXXX.
NO NO Yes None
of the Ethernet port.
Indicates the
loopback status of NO NO Yes None
the Ethernet port.
Indicates whether
the Ethernet port is
in the steady state
of the OAM 3AH NO NO Yes None
loopback response.
For details, see
IEEE 802.3ah.
Indicates whether
the Ethernet OAM NO NO Yes None
3AH is enabled.
Indicates the
number of packets
NO NO Yes None
received at the
Ethernet port.
Indicates the
number of bytes
NO NO Yes None
received at the
Ethernet port.
Indicates the
number of CRC
error packets NO NO Yes None
received at the
Ethernet port.
Indicates the traffic
received at the NO NO Yes None
Ethernet port.
Indicates the
number of packets
NO NO Yes None
transmitted at the
Ethernet port.
Indicates the
number of bytes
NO NO Yes None
transmitted at the
Ethernet port.
transmitted at the NO NO Yes None
Ethernet port.
Indicates the
number of IP
addresses NO NO Yes None
configured for the
Ethernet port.
Indicates the IP
address and mask
NO NO Yes None
list configured for
the Ethernet port.
Indicates the
negotiation mode
NO NO Yes None
configured on the
Ethernet port.
negotiation mode of NO NO Yes None
the Ethernet port.
Indicates the speed
mode of the
Ethernet port. This
parameter must be NO NO Yes None
set to the same
value as that of the
peer port.

mode of the
Ethernet port. If an
Ethernet electrical
port is used, this
parameter is valid
NO NO Yes None
when SPEED is not
set to AUTO. If an
Ethernet optical
port is used, this
parameter must be
set to FULL.
Indicates the
negotiation mode of
NO NO Yes None
the NE connecting
to the Ethernet port.
Indicates the speed

mode of the NE
NO NO Yes None
connecting to the
Ethernet port.

mode of the NE
NO NO Yes None
connecting to the
Ethernet port.
Indicates the
physical layer
NO NO Yes None
status of the
Ethernet port.
Indicates the
cabinet number of
LOFD-003008 /
TDLOFD-003008
Ethernet trunk is
established.
Indicates the
number of the
subrack housing LOFD-003008 /
YES NO No
the board where the TDLOFD-003008
Ethernet trunk is
established.
Indicates the
number of the slot
LOFD-003008 /
housing the board YES YES No
TDLOFD-003008
where the Ethernet
trunk is established.
Indicates the
number of the
Ethernet
trunk.When the
board is a UTRPc
board, the value of
this parameter LOFD-003008 /
YES NO No
ranges from 0 to 2. TDLOFD-003008
When the board is
a board other than
the UTRPc board,
the value of this
parameter ranges
from 0 to 1.
Indicates the type

of Ethernet trunk.
set to DISABLE,
member ports of
the Ethernet trunk
must be manually
configured. In this
case, the
configured member
ports are
considered as valid
member ports of
the Ethernet trunk. LOFD-003008 /
NO NO No
set to ENABLE,
member ports of
the Ethernet trunk
must also be
manually
configured. In this
case, the valid
member ports of
the Ethernet trunk
are negotiated
between the BS
and the peer end
according to LACP.
Indicates whether
to enable the ARP
proxy function on
the Ethernet trunk.
set to ENABLE, the
BS performs the
ARP proxy on the
IP addresses of its
loopback interfaces
(or of the lower-
level BS). If this
LOFD-003008 /
TDLOFD-003008
DISABLE, the BS
does not perform
the ARP proxy on
the IP addresses of
its loopback
interfaces (or of the
lower-level BS).
The external device
on the same subnet
needs to access the
IP address through
a configured route.
Indicates the type

of subboard on the
LOFD-003008 /
TDLOFD-003008
Ethernet trunk is
established.
the Maximum
Transmission Unit
(MTU) in the
Ethernet trunk. The
recommended MTU
value is above 776. LOFD-003008 /
NO NO No
If the value is TDLOFD-003008
smaller than 776,
broadcast packets
such as the DHCP
packet fail to be
received or
transmitted.

of the Ethernet
trunk. The state of
the Ethernet trunk
depends on the
state of the member
LOFD-003008 /
ports. If the state of NO NO Yes
TDLOFD-003008
the member ports
of the existing
Ethernet trunk is
activated, the state
of the Ethernet
trunk is activated.
Indicates the MAC

address of the
Ethernet trunk. The
format is XXXX-
XXXX-XXXX. The LOFD-003008 /
NO NO Yes
MAC address of an TDLOFD-003008
Ethernet port is that
of the first Ethernet
port added to the
Ethernet trunk.
Indicates the MAC
address of the
Ethernet trunk at
the peer end. The
format is XXXX-
XXXX-XXXX. If the
Ethernet trunk type
is set to ENABLE,
this parameter LOFD-003008 /
NO NO Yes
specifies the MAC TDLOFD-003008
address of the peer
end, which is
negotiated between
the BS and the peer
end by using the
LACP protocol. For
details, see IEEE
802.3ad.
Indicates the
number of member LOFD-003008 /
NO NO Yes
ports in the TDLOFD-003008
Ethernet trunk.
Indicates the
NO NO Yes
member port of the TDLOFD-003008
Ethernet trunk.
Indicates the
number of active LOFD-003008 /
NO NO Yes
member ports of TDLOFD-003008
the Ethernet trunk.
Indicates the
number of an active LOFD-003008 /
NO NO Yes
member port of the TDLOFD-003008
Ethernet trunk.
Indicates the
number of packets
(including the LOFD-003008 /
NO NO Yes
discarded packets) TDLOFD-003008
received by the
Ethernet trunk.
Indicates the
number of bytes
NO NO Yes
discarded bytes) TDLOFD-003008
received by the
Ethernet trunk.
Indicates the
number of
LOFD-003008 /
discarded packets NO NO Yes
TDLOFD-003008
received by the
Ethernet trunk.
Indicates the
number of
LOFD-003008 /
discarded bytes NO NO Yes
TDLOFD-003008
received by the
Ethernet trunk.
Indicates the
number of packets
NO NO Yes
discarded packets) TDLOFD-003008
transmitted by the
Ethernet trunk.
Indicates the
number of bytes
NO NO Yes
discarded bytes) TDLOFD-003008
transmitted by the
Ethernet trunk.
Indicates the
number of
LOFD-003008 /
TDLOFD-003008
transmitted by the
Ethernet trunk.
Indicates the
number of
LOFD-003008 /
discarded bytes NO NO Yes
TDLOFD-003008
transmitted by the
Ethernet trunk.
Indicates the
number of IP
LOFD-003008 /
addresses NO NO Yes
TDLOFD-003008
configured for the
Ethernet trunk.
Indicates the IP
LOFD-003008 /
address list of the NO NO Yes
TDLOFD-003008
Ethernet trunk.
Indicates the
number of the
cabinet housing the
LOFD-003008 /
board where the YES NO No
TDLOFD-003008
member port of an
Ethernet trunk is
located.
Indicates the
number of the
subrack housing
LOFD-003008 /
TDLOFD-003008
member port of an
Ethernet trunk is
located.
Indicates the
number of the slot
housing the board LOFD-003008 /
YES YES No
where the member TDLOFD-003008
port of an Ethernet
trunk is located.
Indicates the
YES NO No
parent Ethernet TDLOFD-003008
trunk of the port.
Indicates the
YES YES No
member port in an TDLOFD-003008
Ethernet trunk.
Indicates the
priority of the
member port in an
LOFD-003008 /
Ethernet trunk. A NO NO No
TDLOFD-003008
smaller parameter
value indicates a
higher priority.
Indicates whether
the member port is
the primary port of
an Ethernet trunk.
Each Ethernet trunk
has one and only
one primary port. LOFD-003008 /
NO YES No
The primary port TDLOFD-003008
must be the first
port added to an
Ethernet trunk and
the last port
removed from the
Ethernet trunk.
Indicates the type

of sub-board on the
board where the LOFD-003008 /
YES YES No
member port of an TDLOFD-003008
Ethernet trunk is
located.

of the member port LOFD-003008 /
NO NO Yes
in an Ethernet TDLOFD-003008
trunk.
Indicates the MAC
address of the
member port when
being added to an LOFD-003008 /
NO NO Yes
Ethernet trunk. The TDLOFD-003008
format of the MAC
address is XXXX-
XXXX-XXXX.

mode of
transmitting the
LACP Protocol Data
Units (PDUs) at the
local end. In long LOFD-003008 /
NO NO Yes
period mode, the TDLOFD-003008
time interval for
periodically
transmitting the
LACP PDUs is
large.
mode of
LOFD-003008 /
transmitting the NO NO Yes
TDLOFD-003008
LACP PDUs at the
peer end.
Indicates the
number of received
LOFD-003008 /
LACP PDUs on the NO NO Yes
TDLOFD-003008
member port of an
Ethernet trunk.
Indicates the
number of
transmitted LACP LOFD-003008 /
NO NO Yes
PDUs on the TDLOFD-003008
member port of an
Ethernet trunk.
Indicates the
number of the
YES YES No None
extension user data
type.
Indicates the ID of
the transport
parameter group
related to the NO YES No None
services
corresponding to an
extended QCI.
Indicates the ID of
the transport
parameter group
related to the
service that
YES YES No None
corresponds to the
extended QCI. It
transport parameter
group.
Indicates the
priority of the
service data, which
is identified by a
DSCP value. The
NO YES No None
priority of the
service data has a
with the DSCP
value.
Indicates the
activity factor of the
services NO NO No None
corresponding to an
extended QCI.
Indicates the type

of primary transport
resource used to
transmit the user
date when hybrid
transmission is
adopted. HQ
indicates that high-
quality transport
resources are used,
while LQ indicates
that low-quality
transport resources NO YES No None
are used. When a
new service
requests admission
and admission
control is
performed, one of
the IP path routes
with transport
resources of the
same quality is
used as the primary
transport path.
Indicates the
primary port load
threshold of the
user data in the
hybrid transmission
NO YES No None
scenario. A larger
services are more
likely to be admitted
to the primary path.
Indicates the
primary-to-
secondary port load
ratio threshold of
user data in the
hybrid transmission NO YES No None
scenario. A smaller
services are more
likely to be admitted
to the primary path.
Indicates the type

LOFD-003014 /
of the flood packet YES YES No
TDLOFD-003014
to be measured.
Indicates whether
to enable the
LOFD-003014 /
protection against NO NO No
TDLOFD-003014
excessive flood
packets.
Indicates the
threshold for
starting the
protection against
excessive flood
packets. If the
DFDSW parameter
is set to ENABLE,
the system discards
the extra packets
LOFD-003014 /
when the RX rate of NO YES No
TDLOFD-003014
flood packets
exceeds the
threshold. It is
recommended that
the difference
between Defend
Threshold and
Alarm Threshold is
greater than 3% of
Defend Threshold.
Indicates whether
to report an alarm
when the local end LOFD-003014 /
NO NO No
receives excessive TDLOFD-003014
flood packets from
the peer end.
Indicates the
threshold for the
excessive flood
packet alarm. If the
ALMSW parameter
is set to ENABLE,
the system
measures the RX
rate of flood
packets every 10
seconds. If the
measured value
exceeds the
threshold, an
excessive flood LOFD-003014 /
NO YES No
packet alarm is TDLOFD-003014
reported. The alarm
is cleared if the RX
rate of flood
packets keeps
below the threshold
for five consecutive
minutes. It is
recommended that
the difference
between Defend
Threshold and
Alarm Threshold is
greater than 3% of
Defend Threshold.
Indicates the
number of packets
discarded because
LOFD-003014 /
the number of flood NO NO Yes
TDLOFD-003014
packets exceeds
the specified
threshold.
Indicates the total
LOFD-003014 /
TDLOFD-003014
attack packets.
associated
resource groups
exceeds the
bandwidth of the
physical port, each
resource group is
allocated a
bandwidth that is
directly proportional
to its configured TX
bandwidth; (2) If
this parameter is
set to ENABLE and
the sum of TX
bandwidths of the
associated
resource groups
exceeds the
bandwidth of the LOFD-00301101 /
NO NO No
physical port, each TDLOFD-00301101
resource group is
allocated a
bandwidth that is
directly proportional
to its scheduling
weight. When
RATECFGTYPE
(the rate
configuration type)
is set to
DUAL_RATE,
different values of
this parameter lead
to different CIR
allocation methods
as follows: (1) If the
sum of CIRs of the
associated
Indicates the rate
configuration mode
of transmission
resource groups in
the BS, which can
be set to
SINGLE_RATE or
DUAL_RATE. The
dual rate
configuration refers
to the hybrid of the
peak information
rate (PIR) and
committed
information rate
(CIR). If this
parameter is set to
SINGLE_RATE, the
transmission LOFD-003011 /
NO NO No
resource group TDLOFD-003011
performs traffic
shaping based on
its transmit
bandwidth. If this
parameter is set to
DUAL_RATE, the
transmission
resource group
performs traffic
shaping based on
PIR and the
transmission
admission algorithm
ensures that the
non-flow-
controllable traffic
does not exceed
CIR.
Indicates the
interval between
the time single-hop
BFD detects that
the state of the
LOFD-003011 /
active route NO NO No
TDLOFD-003011
changes from
DOWN to UP and
the time the active
route becomes
available.
Indicates the aging

time of a dynamic
ARP entry of the
BS. This parameter
does not change NO NO No None
the ARP aging time
of the local
maintenance
Ethernet port.
Indicates the IKE LOFD-003009 /
NO NO No
local name. TDLOFD-003009
Indicates the time

interval for sending
the keepalive
packets. If the LOFD-003009 /
NO NO No
0, keepalive
packets are not
sent.
Indicates the
timeout duration for
waiting for the
keepalive packets. LOFD-003009 /
NO NO No
set to 0, keepalive
packets are not
sent.
Indicates the DSCP

LOFD-003009 /
for IKE negotiation NO NO No
TDLOFD-003009
packets.
Indicates the
LOFD-003009 /
cabinet number of NO NO Yes
TDLOFD-003009
the IKE local board.
Indicates the
LOFD-003009 /
subrack number of NO NO Yes
TDLOFD-003009
the IKE local board.
Indicates the slot
LOFD-003009 /
number of the IKE NO NO Yes
TDLOFD-003009
local board.
Indicates the name
YES YES No None
of the IKE peer.
Indicates the ID of
LOFD-003009 /
the IKE proposal in NO YES No
TDLOFD-003009
use.
Indicates the IKE LOFD-003009 /

NO NO No
protocol version. TDLOFD-003009
Indicates the IKE
exchange mode. In
main mode, keys
are exchanged
independently from
identity
authentications.
This protects LOFD-003009 /
NO NO No
identity information TDLOFD-003009
and hence
enhances security.
The aggressive
mode does not
have identity
authentication
protection.
Indicates the type

of the identification
payload that the
local end transmits.
LOFD-003009 /
The authentication NO YES No
TDLOFD-003009
can be performed
based on IP or fully
qualified domain
name (FQDN).
Indicates the IP
address of the peer
end. When the
encapsulation
mode of the IPSec
proposal is the
transmission mode,
the IP address of LOFD-003009 /
NO YES No
the IKE peer must TDLOFD-003009
be the same as the
destination IP
address of the ACL
rule. If they are
different, encoded
packets will fail to
be decoded.

NO YES No
of the peer end. TDLOFD-003009
Indicates the pre-
shared key. The two
negotiation ends
must be configured
with the same
authenticator. This
parameter takes
LOFD-003009 /
effect only when NO YES No
TDLOFD-003009
Authentication
Method in the
corresponding
IKEPROPOSAL is
set to
PRE_SHARED_KE
Y.
Indicates whether
to enable the dead LOFD-003009 /
NO NO No
peer detection TDLOFD-003009
(DPD) function.
Indicates the DPD
idle time. If the local
end does not
receive encrypted
packets for a time
defined by this
parameter, it sends
LOFD-003009 /
a DPD packet to NO NO No
TDLOFD-003009
perform dead peer
detection. The
a DPD packet
slightly varies in
various network
environments.
Indicates the
interval at which
DPD detection
frames are sent.
The interval at
which DPD
detection frames LOFD-003009 /
NO NO No
are sent may TDLOFD-003009
slightly vary in
various network
environments such
as network
congestion, delay,
and jitter.
Indicates the
number of
LOFD-003009 /
retransmission NO NO No
TDLOFD-003009
attempts after a
DPD detection fails.
Indicates the IP
end, which is used
in IKE negotiation.
This IP address can
be set to 0.0.0.0 or
a configured
interface IP address
at the local end. If
this parameter is
set to 0.0.0.0, the
BS automatically
uses the interface
IP address to
negotiate with the
peer. If multiple IP
addresses are LOFD-003009 /
NO NO No
configured at the TDLOFD-003009
port, it is
recommended that
you specify one IP
address for the
negotiation. If the
local BS uses the
digital certificate
and IP address for
authentication in
the negotiation,
ensure that the IP
address in the
certificate is the
same as the local
IP address of the
BS.
Indicates the
LOFD-003009 /
cabinet number of NO NO Yes
TDLOFD-003009
the IKE peer board.
Indicates the
LOFD-003009 /
subrack number of NO NO Yes
TDLOFD-003009
the IKE peer board.
Indicates the slot
LOFD-003009 /
number of the IKE NO NO Yes
TDLOFD-003009
peer board.
Indicates the name
of the IPv6 IKE YES YES No None
peer.
Indicates the ID of
LBFD-003006 /
the security
TDLBFD-003006
proposal used by NO YES No
LOFD-003024 /
an IPv6 IKE
TDLOFD-003024
negotiation.
LBFD-003006 /
Indicates the
TDLBFD-003006
protocol version of NO NO No
LOFD-003024 /
the IPv6 IKE.
TDLOFD-003024
Indicates the IPv6
IKE negotiation
mode. In main
mode, keys are
exchanged
independently from
identity
authentications.
This protects
identity information LBFD-003006 /
and hence TDLBFD-003006
NO NO No
enhances security. LOFD-003024 /
The aggressive TDLOFD-003024
mode does not
have identity
authentication
protection. This
mode, however,
meets the
requirements in
specific network
environments.
Indicates the type

of the identification
payload that the
local end transmits
LBFD-003006 /
in IPv6 networks.
TDLBFD-003006
The authentication NO YES No
LOFD-003024 /
can be performed
TDLOFD-003024
based on IPv6
address or fully
qualified domain
name (FQDN).
Indicates the IPv6

address of the peer
end. If the
encapsulation
mode of an IPSec
proposal is set to
LBFD-003006 /
TRANSPORT, the
TDLBFD-003006
peer IPv6 address NO YES No
LOFD-003024 /
must be the same
TDLOFD-003024
as the destination
IPv6 address of the
ACL rule.
Otherwise,
encrypted packets
fail to be decrypted.
Indicates the peer LBFD-003006 /
name used by an TDLBFD-003006
NO YES No
negotiation. TDLOFD-003024
Indicates the
authenticator of the
pre-shared key in LBFD-003006 /
IPv6 networks. The TDLBFD-003006
NO YES No
two negotiation LOFD-003024 /
ends must be TDLOFD-003024
configured with the
same authenticator.
Indicates whether
LBFD-003006 /
to enable the Dead
TDLBFD-003006
Peer Detection NO NO No
LOFD-003024 /
(DPD) function in
TDLOFD-003024
IPv6 networks.
Indicates the IPv6

DPD idle time. If the
local end does not
receive encrypted
packets for a period
specified by this LBFD-003006 /
parameter, it sends TDLBFD-003006
NO NO No
a DPD packet to LOFD-003024 /
perform dead peer TDLOFD-003024
detection. Time
required to transmit
DPD packets varies
with network
conditions.
Indicates the
the IPv6 DPD
detection frame.
The interval at
which IPv6 DPD LBFD-003006 /
detection frames TDLBFD-003006
NO NO No
are sent may LOFD-003024 /
slightly vary in TDLOFD-003024
various network
environments such
as network
congestion, delay,
and jitter.
Indicates the
LBFD-003006 /
number of
TDLBFD-003006
retransmissions NO NO No
LOFD-003024 /
after the IPv6 DPD
TDLOFD-003024
detection fails.
Indicates the IPv6
address that is
used by the local
end in IPv6 IKE
negotiation. This IP
address can be set
to either
0:0:0:0:0:0:0:0 or a
device IPv6
address configured
at the local end. If
this parameter is
LBFD-003006 /
set to
TDLBFD-003006
0:0:0:0:0:0:0:0, the NO NO No
LOFD-003024 /
BS automatically
TDLOFD-003024
uses a local
interface IP address
to negotiate with
the peer end. If
multiple interface
IPv6 addresses are
configured for a
port, it is
recommended that
this parameter be
set to one of the IP
addresses.
cabinet number of TDLBFD-003006
NO NO Yes
the IPv6 IKE peer LOFD-003024 /
board. TDLOFD-003024
subrack number of TDLBFD-003006
NO NO Yes
the IPv6 IKE peer LOFD-003024 /
board. TDLOFD-003024
LBFD-003006 /
Indicates the slot
TDLBFD-003006
number of the IPv6 NO NO Yes
LOFD-003024 /
IKE peer board.
TDLOFD-003024
Indicates the ID of
YES YES No None
the IKE proposal.
Indicates the
encryption
algorithm used in
the IKE proposal.
The Data
Encryption
Standard (DES) is
an internationally
used data
encryption
algorithm, which
uses a 56-bit key.
The 3DES is also
an internationally
used encryption
algorithm, which LOFD-003009 /
NO NO No
uses a 168-bit key. TDLOFD-003009
The Advanced
Encryption
Standard (AES) is
an advanced
encryption
algorithm, which
provides three
types of key of
different lengths:
128, 192, and 256
bits. Thus, different
protection levels
are available. For
details, see
RFC2401.
IKE uses hashed
message
authentication code
(HMAC) or cipher
block chaining-
message
authentication code
(CBC-MAC) for
identity
authentication and
data integrity check.
HMAC is based on
two hash functions:
message digest
algorithm 5 (MD5)
and secure hash
algorithm 1 (SHA1).
MD5 uses a 128-bit
secret key, whereas NO NO No None
SHA1 uses a 160-
bit secret key. MD5
provides faster
calculation but
lower security than
SHA1. For details
about the two
algorithms without
HMAC, see
RFC2409. For
details about the
two algorithms with
HMAC, see
RFC4306. AES-
XCBC-MAC-96 is
an enhancement to
CBC-MAC and
applies only to
Indicates the
authentication
mode used in the LOFD-003009 /
NO NO No
IKE proposal. For TDLOFD-003009
details, see
RFC2409.
Indicates the Diffie-
Hellman (DH) group
of the IKE proposal.
The core
technology used in
an IKE proposal is
the Diffie-Hellman
(DH) exchange
technology. The DH
exchange
technology is used LOFD-003009 /
NO NO No
to calculate private TDLOFD-003009
information based
on public
information. It is
mathematically
proven that
decrypting the DH
information is
impractical due to
calculation
complexity.
Indicates the life

cycle of an ISAKMP
SA. ISAKMP refers
to Internet Security
Association and
Key Management
Protocol, and SA
refers to security
association.
IKE negotiation
requires a long time
to calculate Diffie-
Hellman (DH) keys.
It is recommended
that this parameter
be set to greater
than 10 minutes so
that the update of LOFD-003009 /
NO NO No
the ISAKMP SA TDLOFD-003009
does not affect the
secure
communication.
Before the SA life
cycle elapses, local
and peer ends will
negotiate with each
other to generate a
new SA to replace
the original one.
The new SA is used
upon completion of
the negotiation, and
the original SA is
automatically
removed once its
life cycle elapses.
Indicates the
Pseudo-random
Function (PRF)
algorithm used in
IKEv2. The PRF
algorithm is used to
generate the LOFD-003009 /
NO NO No
materials required TDLOFD-003009
for IKE
authentication and
encryption. For
details about how to
generate materials,
see RFC4306.
Indicates the
cabinet number of
LOFD-003009 /
the board that NO NO Yes
TDLOFD-003009
adopts the IKE
security proposal.
Indicates the
subrack number of
LOFD-003009 /
TDLOFD-003009
adopts the IKE
security proposal.
Indicates the slot
number of the
LOFD-003009 /
board that adopts NO NO Yes
TDLOFD-003009
the IKE security
proposal.
Indicates the
number of the
cabinet housing the MRFD-231501
board where a YES NO No LOFD-003002 /
resource group is
established.
Indicates the
number of the
subrack that
MRFD-231501
houses the board
YES NO No LOFD-003002 /
where a
TDLOFD-003002
transmission
resource group is
established.
Indicates the
number of the slot
corresponding to MRFD-231501
the board where a YES YES No LOFD-003002 /
resource group is
established.
Indicates the ID of a MRFD-231501

transmission YES NO No LOFD-003002 /
resource group. TDLOFD-003002
Indicates the
destination IP
address of the MRFD-231501
service flow that is YES YES No LOFD-003002 /
bound to a TDLOFD-003002
transmission
resource group.
Indicates the
subnet mask of the
destination IP MRFD-231501
address of the YES YES No LOFD-003002 /
service traffic bound TDLOFD-003002
to a transmission
resource group.
Indicates the bearer MRFD-231501

type of transmission YES NO No LOFD-003002 /
Indicates the type

of sub-board on the
MRFD-231501
board where a
transmission
TDLOFD-003002
resource group is
established.
Indicates the type
of port where a MRFD-231501
transmission YES YES No LOFD-003002 /
resource group is TDLOFD-003002
carried.
Indicates the
number of the port
MRFD-231501
where a
YES NO No LOFD-003002 /
transmission
TDLOFD-003002
resource group is
carried.
Indicates whether
to perform ARP
spoofing checks. If
this parameter is
set to ENABLE, an
alarm is reported
LOFD-003014 /
when ARP spoofing NO NO No
TDLOFD-003014
attacks occur. If this
parameter is set to
DISABLE, no alarm
is reported when
ARP spoofing
attacks occur.
Indicates the ARP
spoofing alarm
threshold. When
the ARP spoofing
check switch is
turned on, an ARP
spoofing alarm is
reported if the
number of ARP
update attempts
reaches this
threshold within one LOFD-003014 /
NO NO No
minute. Note that TDLOFD-003014
the number of ARP
update attempts
from trusted MAC
addresses is not
counted. This alarm
is cleared if no ARP
update attempt is
made in one minute
after the ARP
spoofing alarm is
reported.
Indicates whether
to enable APR
learning strict. ARP
learning strict is a
function that
enables a BS to
learn the
acknowledgement
LOFD-003014 /
packets in response NO NO No
TDLOFD-003014
to only ARP request
packets sent by
itself. With ARP
learning strict, the
BS can reject most
ARP request and
acknowledge
packet attacks.
Indicates whether
to report an alarm
when the number of
invalid packets
received by a BS
exceeds the
specified threshold.
set to ENABLE, an
alarm is reported
when the number of
invalid packets
received by a BS
LOFD-003014 /
exceeds the NO NO No
TDLOFD-003014
set to DISABLE, no
alarm is reported
when the number of
invalid packets
received by a BS
exceeds the
Invalid packets are
those filtered
according to the
packet filter criteria.
Indicates the
threshold for the
excessive flood
packet alarm. When
Invalid Packet
Check Switch is set
to ENABLE, the
system measures
the RX rate of
invalid packets
every 10 seconds.
LOFD-003014 /
If the measured NO NO No
TDLOFD-003014
value exceeds this
threshold, an
excessive invalid
packet alarm is
reported. The alarm
is cleared if the RX
rate of invalid
packets keeps
below the threshold
for 5 consecutive
minutes.
Indicates whether
LOFD-003014 /
to detect IPSec NO NO No
TDLOFD-003014
packet replay.
Indicates the IPSec
LOFD-003014 /
anti-replay alarm NO NO No
TDLOFD-003014
threshold.

NO NO Yes
of physical port. TDLOFD-003014

NO NO Yes
number of a port. TDLOFD-003014
Indicates the
source MAC LOFD-003014 /
NO NO Yes
address of an TDLOFD-003014
invalid packet.
Indicates the
destination MAC LOFD-003014 /
NO NO Yes
invalid packet.
Indicates the VLAN
LOFD-003014 /
ID of an invalid NO NO Yes
TDLOFD-003014
packet.
Indicates the type

of MAC-layer
protocol used by an
invalid packet. A BS
interprets only the
LOFD-003014 /
supported MAC- NO NO Yes
TDLOFD-003014
layer protocols and
only displays the
protocol numbers of
other MAC-layer
protocols.
Indicates the
LOFD-003014 /
source IP address NO NO Yes
TDLOFD-003014
of an invalid packet.
Indicates the
destination IP LOFD-003014 /
NO NO Yes
invalid packet.
Indicates the
protocol used at the
IP layer of an
invalid packet. A BS
interprets only the
LOFD-003014 /
supported IP-layer NO NO Yes
TDLOFD-003014
protocols and only
displays the
protocol numbers of
other IP-layer
protocols.
Indicates the
LOFD-003014 /
source port number NO NO Yes
TDLOFD-003014
of an invalid packet.
Indicates the
NO NO Yes
number of an TDLOFD-003014
invalid packet.
Indicates at most
LOFD-003014 /
the first 64 bytes of NO NO Yes
TDLOFD-003014
an invalid packet.
Indicates the index

LBFD-003006 /
of the IPv6 YES YES No
TDLBFD-003006
interface.
Indicates the type

of the IPv6
LBFD-003006 /
interface, which can NO NO No
TDLBFD-003006
be set to NORMAL
or VLAN.
Indicates the
number of the
cabinet housing the LBFD-003006 /
NO NO No
board where the TDLBFD-003006
IPv6 interface is
located.
Indicates the
subrack number of
LBFD-003006 /
TDLBFD-003006
IPv6 interface is
located.
Indicates the slot
number of the
LBFD-003006 /
board where the NO YES No
TDLBFD-003006
IPv6 interface is
located.
Indicates the type
of sub-board on the
LBFD-003006 /
board where the NO YES No
TDLBFD-003006
IPv6 interface is
located.
Indicates the port

LBFD-003006 /
type of IPv6 NO YES No
TDLBFD-003006
interface.
Indicates the port
LBFD-003006 /
number of the IPv6 NO YES No
TDLBFD-003006
interface.
Indicates the ID of
LBFD-003006 /
the VLAN-type IPv6 NO YES No
TDLBFD-003006
interface.
Indicates the
maximum LBFD-003006 /
NO NO No
transmission unit of TDLBFD-003006
the IPv6 interface.
Indicates whether
LBFD-003006 /
an IPv6 interface is NO NO Yes
TDLBFD-003006
already activated.
Indicates the valid
LBFD-003006 /
link-local address of NO NO Yes
TDLBFD-003006
an IPv6 interface.
Indicates the
number of valid
LBFD-003006 /
global unicast NO NO Yes
TDLBFD-003006
addresses of an
IPv6 interface.
valid global unicast LBFD-003006 /
NO NO Yes
addresses of an TDLBFD-003006
IPv6 interface.
Indicates the
number of valid LBFD-003006 /
NO NO Yes
multicast addresses TDLBFD-003006
of an IPv6 interface.
valid multicast LBFD-003006 /
NO NO Yes
IPv6 interface.
Indicates whether
to enable the IPv6
interface to detect LBFD-003006 /
NO NO Yes
address conflicts TDLBFD-003006
during neighbor
discovery.
Indicates the
number of detection
times during the LBFD-003006 /
NO NO Yes
neighbor discovery TDLBFD-003006
procedure of the
IPv6 interface.
Indicates the time
for the IPv6
LBFD-003006 /
interface to start a NO NO Yes
TDLBFD-003006
neighbor discovery
procedure.
Indicates the
interval between
the time the IPv6
interface reinitiates
neighbor discovery LBFD-003006 /
NO NO Yes
and the time TDLBFD-003006
neighbor discovery
fails or the ND table
entry becomes
invalid.
Indicates whether
to enable the IPv6
interface to LBFD-003006 /
NO NO Yes
automatically TDLBFD-003006
generate a link local
address.
Indicates the
stateless automatic
LBFD-003006 /
configuration switch NO NO Yes
TDLBFD-003006
of the IPv6
interface.
Indicates the ID of
YES YES No None
an IP path.
Indicates the
cabinet number of
NO NO No None
the board where the
IP path is located.
Indicates the
subrack number of
NO NO No None
the board where the
IP path is located.
Indicates the slot
number of the
NO YES No None
board where the IP
path is located.
Indicates the
physical port type of NO YES No None
the IP path.
Indicates the
number of the
NO NO No None
physical port of the
IP path.
Indicates the type

of the IP path. QOS
indicates that this IP
path is used to
carry the service
with specified
Quality of Service
(QoS), that is, with
a specified DSCP. NO NO No None
ANY indicates that
this IP Path can be
used to carry
services of any
QoS and hence is
used to carry the
service without a
specified DSCP.
Indicates the
differentiated
services code point
NO YES No None
(DSCP) of the
services carried on
an IP path.
Indicates the local
IP address of an IP
path. The value
0.0.0.0 indicates NO YES No None
that the local IP
address needs to
be negotiated.
Indicates the peer

IP address of the IP NO YES No None
path.
Indicates the ID of
the adjacent
signaling point to
which the IP path
belongs. This
parameter is valid
only when the
APPTYPE
parameter is set to
NO YES No None
X2 and must be set
to the ID of the
associated X2
interface. Note that
the SCTP link
referenced by this
X2 interface must
be an IPv4 SCTP
link.
Indicates the type
of transport
resource for the IP
path. The value HQ
indicates high-
quality transport
resources, and the
value LQ indicates
low-quality transport NO NO No None
resources. This
parameter must be
set in the
hybridtransmission
scenario. In other
scenarios, the
default value of this
parameter is used.
Indicates the
application type of NO YES No None
IP path.
Indicates whether
to enable the PING
detection to check
the IP path. The
PING detection is
used to check the
connectivity of an IP
path. If the PING
detection is
disabled in the
firewall located in
the transport
network or in the
NO NO No None
CN equipment, a
detection failure will
be resulted, which
will cause the re-
establishment of
the S1 interface
in the cell.
Therefore, this
parameter must be
set to DISABLE
under such
scenarios.

real-time traffic
NO NO Yes None
transmitted on the
IP path.
real-time traffic
NO NO Yes None
received on the IP
path.
non-real-time traffic
NO NO Yes None
transmitted on the
IP path.
NO NO Yes None
received on the IP
path.
TX bandwidth
reserved for the
NO NO Yes None
non-real-time
service transmitted
on the IP path.

RX bandwidth
reserved for the
NO NO Yes None
non-real-time
service received on
the IP path.
Indicates the check

result for an IP
path. If ping
detection and GTP-
U static detection
are simultaneously NO NO Yes None
enabled, the
parameter value
uses the result of
the GTP-U static
detection.
Indicates the ID of
the transmission
resource group NO YES No None
established on an
IP path.
Indicates the
description about
NO NO No None
the peer of the IP
path.
Indicates the type
of sub-board on the
NO YES No None
board where the IP
path is established.
Indicates whether
the IP path joins a
transmission
resource group. If
this parameter is
set to DISABLE, the
NO NO No None
IP path is
established on the
default transmission
resource group on
a specific physical
port.

an IPv6 path, which TDLBFD-003006
YES YES No
identifies a unique LOFD-003017 /
IPv6 path. TDLOFD-003017

the IPv6 path joins TDLBFD-003006
NO NO No
a transmission LOFD-003017 /
Indicates the ID of
LBFD-003006 /
the transmission
TDLBFD-003006
resource group to NO YES No
LOFD-003017 /
which an IPv6 path
TDLOFD-003017
is added.
Indicates the index LBFD-003006 /
of the IPv6 interface TDLBFD-003006
NO YES No
used by an IPv6 LOFD-003017 /
path. TDLOFD-003017
Indicates the type
of IPv6 path. The
value QOS
indicates that the
current IPv6 path
LBFD-003006 /
only carries
TDLBFD-003006
services of a fixed NO YES No
LOFD-003017 /
QoS. The value
TDLOFD-003017
ANY indicates that
the current IPv6
path can carry
services of any
QoS.
Indicates the
Differentiated
LBFD-003006 /
Services Code
TDLBFD-003006
Point (DSCP) of NO YES No
LOFD-003017 /
services allowed to
TDLOFD-003017
be carried on an
IPv6 path.
Indicates the local

IPv6 address of an LBFD-003006 /
IPv6 path. This IPv6 TDLBFD-003006
NO YES No
address must be a LOFD-003017 /
global unicast TDLOFD-003017
address.
Indicates the peer

IPv6 address of an LBFD-003006 /
IPv6 path. This IPv6 TDLBFD-003006
NO YES No
global unicast TDLOFD-003017
address.
Indicates the ID of
the adjacent
signaling point to
which the IPv6 path
belongs. This
parameter is valid
only when the
APPTYPE LBFD-003006 /
NO YES No
X2 and must be set LOFD-003017 /
to the ID of the TDLOFD-003017
associated X2
interface. Note that
the SCTP link
referenced by this
X2 interface must
be an IPv6 SCTP
link.
Indicates the
application type of NO YES No None
IP path.
Indicates whether
to enable ping
detection for an LBFD-003006 /
IPv6 path. Ping TDLBFD-003006
NO NO No
detection can be LOFD-003017 /
used to check the TDLOFD-003017
connectivity of an
IPv6 path.
Indicates the actual LBFD-003006 /

real-time services TDLBFD-003006
NO NO Yes
transmitted on an LOFD-003017 /
IPv6 path. TDLOFD-003017
real-time services TDLBFD-003006
NO NO Yes
received on an IPv6 LOFD-003017 /
path. TDLOFD-003017
non-real-time TDLBFD-003006
NO NO Yes
services transmitted LOFD-003017 /
on an IPv6 path. TDLOFD-003017
non-real-time TDLBFD-003006
NO NO Yes
services received LOFD-003017 /
on an IPv6 path. TDLOFD-003017
Indicates the TX
LBFD-003006 /
bandwidth reserved
TDLBFD-003006
for non-real-time NO NO Yes
LOFD-003017 /
services on an IPv6
TDLOFD-003017
path.
Indicates the RX
LBFD-003006 /
bandwidth reserved
TDLBFD-003006
for non-real-time NO NO Yes
LOFD-003017 /
services on an IPv6
TDLOFD-003017
path.
LBFD-003006 /
Indicates the ping
TDLBFD-003006
check result of the NO NO Yes
LOFD-003017 /
IPv6 path.
TDLOFD-003017

description about TDLBFD-003006
NO NO No
the peer of the IPv6 LOFD-003017 /
path. TDLOFD-003017
Indicates the
source IP address
of an IP path route.
The source IP
YES YES No None
address must be
the same as the
configured device
IP address.
Indicates the
destination IP
YES YES No None
address of an IP
path route.
Indicates the type

of transport
resource carried on
an IP path route.
The value HQ
indicates high- NO YES No None
quality transport
resources, and the
value LQ indicates
low-quality transport
resources.
Indicates the next
hop IP address of
an IP path route.
The next hop IP
address and the
configured device NO YES No None
IP address must be
on the same
network segment,
but cannot be the
same.
Indicates the ID of
LOFD-00301201 /
an IP PM session of YES YES No
TDLOFD-00301201
an NE.
Indicates the local

IP address of an IP
PM session. This IP
address excluding
LOFD-00301201 /
0.0.0.0 must be NO YES No
TDLOFD-00301201
configured at the
Ethernet port,
Ethernet trunk, or
loopback interface.
Indicates the peer
IP address of the IP
PM session. This IP
address must be a
valid IP address of
Class A, B, or C LOFD-00301201 /
NO YES No
and different from TDLOFD-00301201
any existing IP
end. In addition, it
cannot be set to
0.x.x.x or 127.x.x.x.
Indicates the
Differentiated
LOFD-00301201 /
Services Code NO YES No
TDLOFD-00301201
Point (DSCP) of an
IP PM session.
Indicates that the

activation direction
of the IP PM
session. For this
parameter to be
valid, the peer must
also support the IP
PM session. If this
NO NO No
UP, the IP PM TDLOFD-00301201
session initiated by
the BS is activated.
set to BIDIR, the IP
PM sessions
initiated by BS and
the peer are
activated.
Indicates the round-

trip delay calculated
by an IP PM
session detection.
The round-trip
delay is the time LOFD-00301201 /
NO NO Yes
that is consumed to TDLOFD-00301201
transmit IP PM
detection packets to
and fro between the
local and peer
ends.
Indicates the DL
jitter calculated by LOFD-00301201 /
NO NO Yes
an IP PM session TDLOFD-00301201
detection.
Indicates the UL
jitter calculated by LOFD-00301201 /
NO NO Yes
an IP PM session TDLOFD-00301201
detection.
Indicates the DL
packet loss rate
LOFD-00301201 /
calculated by an IP NO NO Yes
TDLOFD-00301201
PM session
detection.
Indicates the UL
packet loss rate
LOFD-00301201 /
calculated by an IP NO NO Yes
TDLOFD-00301201
PM session
detection.
Indicates the UL
LOFD-00301201 /
activation status of NO NO Yes
TDLOFD-00301201
an IP PM session.
Indicates the DL
LOFD-00301201 /
activation status of NO NO Yes
TDLOFD-00301201
an IP PM session.
Indicates the type

of IP PM session. A
triplet consists of
the local IP
address, peer IP
address, and LOFD-00301201 /
NO NO No
protocol type; a TDLOFD-00301201
quadbit consists of
the local IP
address, peer IP
address, protocol
type, and DSCP.
Indicates whether
to bind the IP PM
session to an IP
path. If the IP PM
session is bound to
an IP path, the IP
PM session uses
the local and peer
IP addresses of the
IP path in data
transmission. In
addition, if
TXBWASW or
RXBWASW is set LOFD-00301201 /
NO NO No
to ON and TCSW is TDLOFD-00301201
set to ENABLE in
the algorithm for the
transmission
resource group
associated with the
IP path, the system
dynamically adjusts
the TX or RX
bandwidth of the
transmission
resource group
based on the IP PM
detection result.
Indicates the ID of
the IP path to which LOFD-00301201 /
NO YES No
an IP PM session is TDLOFD-00301201
bound.
Indicates whether
the DSCP value of LOFD-00301201 /
NO NO Yes
a DL IP PM session TDLOFD-00301201
changes.
LOFD-00301201 /
DSCP value of a DL NO NO Yes
TDLOFD-00301201
IP PM session.
Indicates the
modified DSCP LOFD-00301201 /
NO NO Yes
value of a DL IP PM TDLOFD-00301201
session.
Indicates the time
when the DSCP
NO NO Yes None
value of a DL IP PM
session changes.
Indicates whether
the DSCP value of
NO NO Yes None
an UL IP PM
session changes.
DSCP value of an NO NO Yes None
UL IP PM session.
Indicates the
modified DSCP
NO NO Yes None
value of an UL IP
PM session.
Indicates the time
when the DSCP
value of an UL IP NO NO Yes None
PM session
changes.
Indicates the
version of the
negotiated data, NO NO Yes None
when the status of
IP PM is UP.
Indicates the
cabinet number of
YES NO No None
the board where the
IP route is located.
Indicates the
subrack number of
YES NO No None
the board where the
IP route is located.
Indicates the slot

number of the
YES YES No None
board where the IP
route is located.
Indicates the type

of sub-board on the
YES YES No None
board where the IP
route is established.
Indicates the type
YES NO No None
of port.
Indicates the port

YES NO No None
number.
Indicates the type
of route. If this
parameter is set to
NEXTHOP, all the
IP packets that
meet the route
direction are first
forwarded to the
specified next hop YES YES No None
IP address. If this
parameter is set to
IF, all the IP packets
that meet the route
direction are first
forwarded to the
specified egress
port.
Indicates the
destination IP
YES YES No None
address of the
route.
Indicates the
subnet mask for the
destination IP YES YES No None
address of the
route.
Indicates the IP
address of the next YES NO No None
hop.
Indicates the
priority of the
routing table entry.
NO NO No None
A smaller parameter
value indicates a
higher priority.
of the IP route. A
static host route is a
manually
configured route
with the subnet
mask set to
255.255.255.255. A
static gateway route
is a manually
configured route, in
which the subnet
mask is not set to
255.255.255.255
and the next hop IP
address is on a
different network
segment from the
egress port IP
address. A dynamic NO NO Yes None
host route is a
dynamically
generated route
with the subnet
mask set to
255.255.255.255. A
dynamic gateway
route is a
dynamically
generated route, in
which the subnet
mask is not set to
255.255.255.255
and the next hop IP
address is on a
different network
segment from the
egress port IP
Indicates the
description about
NO NO No None
the destination of
the route.
Indicates the type

NO NO Yes None
of the port.
Indicates the port

NO NO Yes None
number.
Indicates the
destination IPv6
YES YES No None
address of the
static IPv6 route.

length of the
LBFD-003006 /
destination IPv6 YES YES No
TDLBFD-003006
address of the
static IPv6 route.
Indicates the next

hop type of static
IPv6 route.
set to NEXTHOP,
all the IP packets
LBFD-003006 /
meeting the route YES NO No
TDLBFD-003006
direction are first
forwarded to the
next hop IPv6
address, and then
forwarded to other
addresses.
Indicates the type
LBFD-003006 /
of next hop IPv6 YES YES No
TDLBFD-003006
address.
Indicates the next

hop IPv6 address of LBFD-003006 /
YES YES No
the static IPv6 TDLBFD-003006
route.
Indicates the index

of the IPv6 interface LBFD-003006 /
YES NO No
to which a static TDLBFD-003006
IPv6 route belongs.
Indicates the
priority of a static
IPv6 route. A LBFD-003006 /
NO NO No
smaller parameter TDLBFD-003006
value indicates a
higher priority.
Indicates the type
of the static IPv6
route. A static host
route is a manually
configured route
with a 128-bit
prefix. A static
gateway route is a
manually
configured route
with a non-128-bit
prefix, with the next
hop IP address on
a different network
segment from the
egress port IP
LBFD-003006 /
address. A dynamic NO NO Yes
TDLBFD-003006
host route is a
dynamically learned
(not manually
configured) route
with a 128-bit
prefix. A dynamic
gateway route is a
dynamically learned
(not manually
configured) route
with a non-128-bit
prefix, with the next
hop IP address on
a different segment
from the egress
port IP address.
Indicates the
description about LBFD-003006 /
NO NO No
the destination of a TDLBFD-003006
static IPv6 route.
Indicates the
cabinet number of
LOFD-003009 /
the port to which YES NO No
TDLOFD-003009
the IPSec policy
group is bound.
Indicates the
subrack number of
LOFD-003009 /
the port to which YES NO No
TDLOFD-003009
the IPSec policy
group is bound.
Indicates the slot
number of the port
LOFD-003009 /
to which the IPSec YES YES No
TDLOFD-003009
policy group is
bound.
Indicates the type
of sub-board on the
board with the port LOFD-003009 /
YES YES No
to which the IPSec TDLOFD-003009
policy group is
bound.
Indicates the type

of port to which the LOFD-003009 /
YES YES No
IPSec policy group TDLOFD-003009
is bound.
Indicates the
number of the port
LOFD-003009 /
to which the IPSec YES YES No
TDLOFD-003009
policy group is
bound.
Indicates the name

LOFD-003009 /
of the IPSec policy NO YES No
TDLOFD-003009
group.
Indicates the
LBFD-003006 /
number of the port
TDLBFD-003006
to which the IPv6 YES YES No
LOFD-003024 /
security policy
TDLOFD-003024
group is bound.
LBFD-003006 /
Indicates the name
TDLBFD-003006
of the IPv6 security NO YES No
LOFD-003024 /
policy group.
TDLOFD-003024
Indicates the ID of
the IPSec tunnel
pair. It uniquely
LOFD-003009 /
identifies a pair of YES YES No
TDLOFD-003009
primary and
secondary IPSec
tunnels.
Indicates the name

of the primary
IPSec policy group.
The primary IPSec LOFD-003009 /
NO YES No
tunnel uses an TDLOFD-003009
IPSec policy in the
primary IPSec
policy group.
Indicates the ID of
the primary IPSec
policy. The primary
IPSec tunnel uses
the primary IPSec LOFD-003009 /
NO YES No
policy, which is TDLOFD-003009
identified by this
parameter and the
MSPGN parameter
together.
Indicates the name

of the secondary
IPSec policy group.
The secondary LOFD-003009 /
NO YES No
IPSec tunnel uses TDLOFD-003009
an IPSec policy in
the secondary
IPSec policy group.
Indicates the ID of
the secondary
IPSec policy. The
secondary IPSec
tunnel uses the
LOFD-003009 /
secondary IPSec NO YES No
TDLOFD-003009
policy, which is
identified by this
parameter and the
SSPGN parameter
together.
Indicates the ID of
the BFD session
LOFD-003009 /
referenced by the NO YES No
TDLOFD-003009
primary IPSec
tunnel.
Indicates the ID of
the BFD session
LOFD-003009 /
referenced by the NO YES No
TDLOFD-003009
secondary IPSec
tunnel.
Indicates the IPSec
policy in use. If the
primary IPSec
tunnel is used, the
IPSec policy in use
is the primary IPSec LOFD-003009 /
NO NO Yes
policy. If the TDLOFD-003009
secondary IPSec
policy is used, the
IPSec policy in use
is the secondary
IPSec policy.
Indicates the name

LOFD-003009 /
of the IPSec policy YES YES No
TDLOFD-003009
group.
Indicates the
sequence No. of
the IPSec policy LOFD-003009 /
YES YES No
group. The smaller TDLOFD-003009
the number, the
higher the priority.
Indicates the ID of
LOFD-003009 /
the access control NO YES No
TDLOFD-003009
list.
Indicates the name

LOFD-003009 /
of the IPSec NO YES No
TDLOFD-003009
proposal.
Indicates the name

of the IKE peer that LOFD-003009 /
NO YES No
is referenced by the TDLOFD-003009
IPSec policy.
BS to use a key
that is not derived
from the first-phase
key, ensuring that
the two keys are
independent of
each other.
According to PFS, a
key protects a
unique set of data.
The elements used
to generate keys
are not reusable. If
a key is decrypted,
other keys are still
secure.
If the IPSec policy
is used to initiate
IPSec negotiation, LOFD-003009 /
NO NO No
a PFS exchange is TDLOFD-003009
launched. If the
PFS is assigned to
the local end, then
the PFS exchange
is required when
the negotiation is
launched at the
peer end. The DH
group assigned to
the local end and
the peer end should
be the same.
Otherwise, the
negotiation fails.
The security level of
the 1024-bit Diffie-
Hellman group (Dh-
group2) is higher
Indicates the
configuration mode
of the IPSec SA life
cycle. If this
parameter is set to
GLOBAL, the
default SA life cycle
is used. In this
LOFD-003009 /
case, LTS and NO NO No
TDLOFD-003009
LTKB are set to the
default values 3600
and 69120000,
respectively. If this
parameter is set to
LOCAL, the SA life
cycle is
configurable.
Indicates the life
cycle of an IPSec
SA. An IPSec SA
becomes invalid
once its life cycle
specified by this
parameter elapses.
Before the life cycle
of an IPSec SA
elapses, the IPSec
policy is used in an
attempt to establish
a new IPSec SA
through negotiation
to ensure secure
transmission;
before the LOFD-003009 /
NO NO No
negotiation is TDLOFD-003009
complete, the
original IPSec SA is
still used. After the
negotiation is
complete, the new
SA is immediately.
IPSec SA
negotiation takes a
period. To prevent
SA updating from
affecting
communication
security, a life cycle
longer than 900
seconds is
recommended.
Indicates the
effective traffic LOFD-003009 /
NO NO No
under the IPSec TDLOFD-003009
policy.
Indicates the
cabinet number of
LOFD-003009 /
TDLOFD-003009
adopts the IPSec
policy.
Indicates the
subrack number of
LOFD-003009 /
TDLOFD-003009
adopts the IPSec
policy.
Indicates the slot
NO NO Yes
board that adopts TDLOFD-003009
the IPSec policy.
the IPSec packet
anti-replay window.
parameter is set to
0, the IPSec packet
anti-replay function
is disabled. If the
value of this
parameter is set to
32, 64, 128, 256,
512, 1024, 2048 or
4096, the system
checks whether the
packets are LOFD-003009 /
NO NO No
duplicate in the TDLOFD-003009
window. A packet is
discarded if it has a
duplicate packet or
its sequence
number is smaller
than any packet in
the window. The
window slides if the
sequence number
of the packet is
larger than any
packet that is
received in the
window.
LBFD-003006 /
Indicates the name
TDLBFD-003006
of the IPv6 IPSec YES YES No
LOFD-003024 /
policy group.
TDLOFD-003024
Indicates the
sequence number
LBFD-003006 /
of the IPv6 IPSec
TDLBFD-003006
policy. A larger YES YES No
LOFD-003024 /
value of this
TDLOFD-003024
parameter indicates
a lower priority.
LBFD-003006 /
Indicates the type
TDLBFD-003006
of the ID of the NO YES No
LOFD-003024 /
access control list.
TDLOFD-003024
LBFD-003006 /
NO YES No
the IPv4 ACL. LOFD-003024 /
TDLOFD-003024
LBFD-003006 /
NO YES No
the IPv6 ACL. LOFD-003024 /
TDLOFD-003024
LBFD-003006 /
Indicates the name
TDLBFD-003006
of the security NO YES No
LOFD-003024 /
proposal.
TDLOFD-003024
Indicates the name

LBFD-003006 /
of the IPv6 IKE
TDLBFD-003006
peer that is NO YES No
LOFD-003024 /
referenced by the
TDLOFD-003024
IPv6 IPSec policy.
that is not derived
from the first-phase
key, ensuring that
the two keys are
independent of
each other.
According to PFS, a
key protects a
unique set of data.
The elements used
to generate keys
are not reusable. If
a key is
compromised, other
keys are still
secure.
If the IPSec policy
LBFD-003006 /
is used to initiate
TDLBFD-003006
IPSec negotiation, NO NO No
LOFD-003024 /
a PFS exchange is
TDLOFD-003024
launched. If the
PFS is assigned to
the local end, then
the PFS exchange
is required when
the negotiation is
launched at the
peer end. The DH
group assigned to
the local end and
the peer end should
be the same.
Otherwise, the
negotiation fails.
The security level of
the 1024-bit Diffie-
Hellman group (Dh-
Indicates the
configuration mode
of the IPv6 IPSec
SA life cycle. The
value GLOBAL
indicates that the
life cycle applies to
all IPSec SAs of the
BS, and the value LBFD-003006 /
LOCAL indicates TDLBFD-003006
NO NO No
the life cycle LOFD-003024 /
applies only to the TDLOFD-003024
current IPSec SA.
When this
parameter is set to
GLOBAL, Lifetime
Based On Time is
3600s and Lifetime
Based On Traffic is
69120000 KB.
Indicates the life
cycle of an IPv6
IPSec SA. When
the lifetime reaches
a specified value,
the IPv6 IPSec SA
becomes invalid.
Before the life cycle
of an IPv6 IPSec
SA elapses, the
IPSec policy is
used in an attempt
to establish a new
IPv6 IPSec SA
through negotiation
to ensure secure
transmission;
LBFD-003006 /
before the
TDLBFD-003006
negotiation is NO NO No
LOFD-003024 /
complete, the
TDLOFD-003024
original IPv6 IPSec
SA is still used.
After the
negotiation is
completed, the new
SA is immediately
used. IPv6 IPSec
SA negotiation
takes a period. To
prevent SA
updating from
affecting
communication
security, a life cycle
longer than 900
seconds is
recommended.

effective traffic of TDLBFD-003006
NO NO No
the IPv6 IPSec LOFD-003024 /
policy. TDLOFD-003024
Indicates the
LBFD-003006 /
cabinet number of
TDLBFD-003006
LOFD-003024 /
adopts the IPv6
TDLOFD-003024
IPsec policy.
Indicates the
LBFD-003006 /
subrack number of
TDLBFD-003006
LOFD-003024 /
adopts the IPv6
TDLOFD-003024
IPSec policy.
Indicates the slot
LBFD-003006 /
number of the
TDLBFD-003006
board that adopts NO NO Yes
LOFD-003024 /
the IPv6 IPSec
TDLOFD-003024
policy.
Indicates the name
of the IPSec YES YES No None
proposal.
Indicates the
encapsulation
mode of an IPSec
proposal, which can
be set to TUNNEL
or TRANSPORT. In
TRANSPORT
mode, only data is
encrypted. In
TUNNEL mode, the
whole IP packet is
protected, and a
new IP header is
added to the
original IP packet.
The source IP
LOFD-003009 /
address and the NO NO No
TDLOFD-003009
destination IP
address of the new
IP header are the IP
addresses of two
ends of the security
tunnel. Both the
TRANSPORT mode
and the TUNNEL
mode are used for
end-to-end IPSec
protection. The
TUNNEL mode,
however, is also
applied to the
protection of a
certain segment.
Indicates the
security protocol
used in an IPSec
proposal. The value
AH indicates the
Authentication
Header (AH)
protocol specified in
RFC2402. The
value ESP indicates
the Encapsulating LOFD-003009 /
NO NO No
Security Payload TDLOFD-003009
(ESP) protocol
specified in
RFC2406. The
value AH_ESP
indicates that the
ESP protocol is
preferentially used
to protect packets,
but not the AH
protocol.
Indicates the
authentication
algorithm used in
AH. IPSec uses
hashed message
authentication code
(HMAC) or cipher
block chaining-
message
authentication code
(CBC-MAC) for
identity
authentication and
data integrity check.
HMAC is based on
three hash
functions: message
digest algorithm 5
LOFD-003009 /
(MD5), secure hash NO NO No
TDLOFD-003009
algorithm 1 (SHA1),
and secure hash
algorithm 256
(SHA256). For
details about the
three algorithms
without HMAC, see
RFC2409. For
details about the
three algorithms
with HMAC, see
RFC4306. AES-
XCBC-MAC-96 is
an enhancement to
CBC-MAC. For
details about AES-
XCBC-MAC-96, see
RFC3566.
Indicates the
authentication LOFD-003009 /
NO NO No
algorithm used in TDLOFD-003009
the ESP.
Indicates the
encryption LOFD-003009 /
NO NO No
algorithm used in TDLOFD-003009
the ESP.
Indicates the
cabinet number of
LOFD-003009 /
TDLOFD-003009
adopts the IPSec
proposal.
Indicates the
subrack number of
LOFD-003009 /
TDLOFD-003009
adopts the IPSec
proposal.
Indicates the slot
NO NO Yes
board that adopts TDLOFD-003009
the IPSec proposal.
Indicates whether
to enable the local
NO NO Yes None
maintenance
Ethernet port.
Indicates the
physical layer
status of the local NO NO Yes None
maintenance
Ethernet port.
Indicates the
number of
discarded packets
that are received at NO NO Yes None
the local
maintenance
Ethernet port.
Indicates the
number of packets
received at the local NO NO Yes None
maintenance
Ethernet port.
Indicates the
number of
discarded packets
that are transmitted NO NO Yes None
at the local
maintenance
Ethernet port.
Indicates the
number of packets
transmitted at the NO NO Yes None
local maintenance
Ethernet port.
maintenance. The
value of this
parameter must
meet the following
conditions:
(1) It must be a
valid IP address of
Class A, B, or C,
and cannot be set
to 0.x.x.x or
127.x.x.x.
(2) It must be
different from the
local IP address of
any remote
maintenance
channel and from
any device IP
address. NO NO No None
(3) It must be on
different network
segments from the
IP address of any
remote
maintenance
channel and from
any device IP
address.
(4) It must be
different from any
IP address
configured on other
ports.
(5) It must be on
different network
segments from the
destination IP
Indicates the
subnet mask of a
local maintenance
channel. This
subnet mask must NO NO No None
be a valid mask
address and cannot
be 0.0.0.0 or
255.255.255.255.
Indicates the IPv6
maintenance
channel. This IPv6 LBFD-003006 /
NO NO No
address must be a TDLBFD-003006
global unicast
address or a link-
local address.

length of the IPv6
LBFD-003006 /
address of a local NO NO No
TDLBFD-003006
maintenance
channel.

of the IPv6 address
LBFD-003006 /
of the local NO NO Yes
TDLBFD-003006
maintenance
channel.
Indicates the time

period during which
the IPv6 address of
LBFD-003006 /
the local NO NO Yes
TDLBFD-003006
maintenance
channel is in valid
state.
Indicates the time

period during which
the IPv6 address of
the local
maintenance
channel is in
preferred state. The
valid state is
categorized into the
preferred state and
the deprecated
state. In preferred
LBFD-003006 /
state, the address NO NO Yes
TDLBFD-003006
can be freely used.
In deprecated state,
the connections
previously
established through
this address are still
usable, whereas
any connection
newly established
through this
address is not
usable.
cabinet number of TDLOFD-00301101
YES NO No
the board where the LOFD-00301102 /
port is located. TDLOFD-00301102

subrack number of TDLOFD-00301101
YES NO No
the board where the LOFD-00301102 /
Indicates the slot LOFD-00301101 /

number of the TDLOFD-00301101
YES YES No
board where the LOFD-00301102 /
LOFD-00301101 /
Indicates the port TDLOFD-00301101
YES YES No
type. LOFD-00301102 /
TDLOFD-00301102
LOFD-00301101 /
Indicates the port TDLOFD-00301101
YES YES No
number. LOFD-00301102 /
TDLOFD-00301102
LOFD-00301101 /
TDLOFD-00301101
for limiting the line NO NO No
LOFD-00301102 /
rate at the port.
TDLOFD-00301102
Indicates the UL
committed LOFD-00301101 /
information rate TDLOFD-00301101
NO YES No
after rate limitation LOFD-00301102 /
is configured at a TDLOFD-00301102
port.
Indicates the
LOFD-00301101 /
Committed Burst
TDLOFD-00301101
Size (CBS) after NO YES No
LOFD-00301102 /
rate limitation is
TDLOFD-00301102
configured at a port.
Indicates the
LOFD-00301101 /
Excess Burst Size
TDLOFD-00301101
(EBS) after rate NO YES No
LOFD-00301102 /
limitation is
TDLOFD-00301102
configured at a port.

of sub-board on the TDLOFD-00301101
YES YES No
board where a port LOFD-00301102 /
is located. TDLOFD-00301102
Indicates the DL
committed
information rate
after rate limitation
LOFD-00301101 /
is configured at a
TDLOFD-00301101
port. This NO YES No
LOFD-00301102 /
parameter
TDLOFD-00301102
computes the value
of Physical Port
Down Link
Admission.
Indicates the
number of the
LBFD-00300403 /
cabinet where the YES NO No
TDLBFD-00300403
MLPPP group is
located.
Indicates the
number of the
LBFD-00300403 /
subrack where the YES NO No
TDLBFD-00300403
MLPPP group is
located.
Indicates the
number of the slot LBFD-00300403 /
YES YES No
where the MLPPP TDLBFD-00300403
group is located.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
MLPPP group.
Indicates whether
an MLPPP group
supports the multi-
class feature.
set to ENABLE, the
LBFD-00300403 /
MLPPP group NO NO No
TDLBFD-00300403
supports the Class
of Service (CoS)
feature and four or
eight service types
of different
priorities.
Indicates the
authentication type LBFD-00300403 /
NO NO No
of the MLPPP TDLBFD-00300403
group.
Indicates the
authentication user LBFD-00300403 /
NO YES No
name of an MLPPP TDLBFD-00300403
group.
Indicates the
LBFD-00300403 /
authentication NO YES No
TDLBFD-00300403
password.
Indicates the local
IP address. If this
parameter is set to
0.0.0.0, this IP
address needs to
be negotiated. If
this parameter is LBFD-00300403 /
NO NO No
not set to 0.0.0.0, it TDLBFD-00300403
must be set to a
valid IP address of
class A, B, or C but
must not be the
reserved address
0.x.x.x or 127.x.x.x.
Indicates the
subnet mask of the
local IP address. If
LBFD-00300403 /
TDLBFD-00300403
set to 0.0.0.0, it
needs to be
negotiated.
Indicates the peer

IP address. When
the eNodeB is
connected to a peer
equipment, the peer
IP address can be
either user- LBFD-00300403 /
NO NO No
specified or set to TDLBFD-00300403
0.0.0.0. If this
parameter is set to
0.0.0.0, this IP
address is obtained
by means of
negotiation.
Indicates the
LBFD-00300403 /
MP/MC head option NO NO No
TDLBFD-00300403
of the MLPPP.
Indicates whether
to enable PPP LBFD-00300403 /
NO NO No
multi-frame TDLBFD-00300403
multiplexing.
Indicates the
LBFD-00300403 /
fragment size of an NO NO No
TDLBFD-00300403
MLPPP group.
Indicates the
maximum length of LBFD-00300403 /
NO NO No
the PPP MUX TDLBFD-00300403
subframe.
Indicates the
maximum length of LBFD-00300403 /
NO NO No
the PPP MUX TDLBFD-00300403
frame.
Indicates the
timeout duration of
a PPP MUX
combination. If the
PPP MUX
combination takes LBFD-00300403 /
NO NO No
longer time than TDLBFD-00300403
this parameter
value, an alarm
related to the PPP
MUX combination
timeout is reported.
Indicates the
LBFD-00300403 /
number of classes NO NO No
TDLBFD-00300403
of service.
Indicates whether
LBFD-00300403 /
to enable IP header NO NO No
TDLBFD-00300403
compression.
Indicates the
threshold above
LBFD-00300403 /
which the MLPPP NO NO No
TDLBFD-00300403
packet loss alarm is
generated.
Indicates the
threshold below
LBFD-00300403 /
which the MLPPP NO NO No
TDLBFD-00300403
packet loss alarm is
cleared.
LBFD-00300403 /
of an MLPPP NO NO Yes
TDLBFD-00300403
group.
LBFD-00300403 /
of the IPCP NO NO Yes
TDLBFD-00300403
protocol.
Indicates the status LBFD-00300403 /

NO NO Yes
of the PPP MUX. TDLBFD-00300403
Indicates the
negotiation result of LBFD-00300403 /
NO NO Yes
the local IP TDLBFD-00300403
address.
Indicates the
LBFD-00300403 /
negotiation result of NO NO Yes
TDLBFD-00300403
the local IP mask.
Indicates the
NO NO Yes
the peer IP TDLBFD-00300403
address.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
the multi-class PPP.
Indicates the
NO NO Yes
the maximum RX TDLBFD-00300403
unit.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
the PPP MUX.
Indicates the
NO NO Yes
the address field TDLBFD-00300403
and control field.
Indicates the
NO NO Yes
the protocol field TDLBFD-00300403
compression.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
the IPHC.
Indicates the
LBFD-00300403 /
number of packets NO NO Yes
TDLBFD-00300403
received.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
sent.
Indicates the RX LBFD-00300403 /
NO NO Yes
traffic. TDLBFD-00300403
Indicates the TX LBFD-00300403 /
NO NO Yes
traffic. TDLBFD-00300403
Indicates the
number of IP LBFD-00300403 /
NO NO Yes
MLPPP group.
LBFD-00300403 /
IP addresses of an NO NO Yes
TDLBFD-00300403
MLPPP group.
Indicates the type

of sub-board on the
LBFD-00300403 /
board where an YES YES No
TDLBFD-00300403
MLPPP group is
established.
Indicates the
LBFD-00300403 /
number of bytes NO NO Yes
TDLBFD-00300403
received.
Indicates the
NO NO Yes
discarded packets TDLBFD-00300403
received.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
transmitted.
Indicates the
NO NO Yes
transmitted.
Indicates the
number of the
LBFD-00300403 /
cabinet where the YES NO No
TDLBFD-00300403
MLPPP sublink is
located.
Indicates the
number of the
LBFD-00300403 /
subrack where the YES NO No
TDLBFD-00300403
MLPPP sublink is
located.
Indicates the
number of the slot LBFD-00300403 /
YES YES No
where the MLPPP TDLBFD-00300403
sublink is located.
Indicates the
LBFD-00300403 /
number of the YES NO No
TDLBFD-00300403
MLPPP sublink.
Indicates the
LBFD-00300403 /
number of the NO NO No
TDLBFD-00300403
MLPPP group.
Indicates the
number of the
subrack housing
LBFD-00300403 /
TDLBFD-00300403
E1/T1 port carrying
the MLPPP sublink
is located.
Indicates the
number of slot
holding the board
LBFD-00300403 /
where the E1/T1 NO YES No
TDLBFD-00300403
port carrying the
MLPPP sublink is
located.
Indicates the
number of the LBFD-00300403 /
NO NO No
E1/T1 port carrying TDLBFD-00300403
the MLPPP sublink.
Indicates the
number of the LBFD-00300403 /
NO YES No
E1/T1 slot carrying TDLBFD-00300403
the MLPPP sublink.
Indicates the
Maximum Receive
Unit (MRU). The
received packet LBFD-00300403 /
NO NO No
whose length is TDLBFD-00300403
greater than this
parameter value is
discarded.
Indicates whether
LBFD-00300403 /
to enable protocol NO NO No
TDLBFD-00300403
field compression.
Indicates whether
to enable the
LBFD-00300403 /
compression of the NO NO No
TDLBFD-00300403
address field and
control field.
Indicates the
timeout duration of LBFD-00300403 /
NO NO No
the MLPPP sublink TDLBFD-00300403
negotiation.
Indicates the type

of sub-board where LBFD-00300403 /
YES YES No
an MLPPP sublink TDLBFD-00300403
is established.
Indicates the type

of sub-board where LBFD-00300403 /
NO YES No
an MLPPP group is TDLBFD-00300403
established.

LBFD-00300403 /
of the MLPPP NO NO Yes
TDLBFD-00300403
sublink.
of the Link Control LBFD-00300403 /
NO NO Yes
Protocol (LCP) TDLBFD-00300403
protocol.
Indicates the
NO NO Yes
the maximum RX TDLBFD-00300403
unit.
Indicates the
NO NO Yes
the protocol field TDLBFD-00300403
compression.
Indicates the
negotiation result of
the Address-And- LBFD-00300403 /
NO NO Yes
Control-Field- TDLBFD-00300403
Compression
(ACFC).
Indicates the type

of sub-board on the
board where the LBFD-00300403 /
NO YES No
E1/T1 port carrying TDLBFD-00300403
the MLPPP sublink
is located.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
received.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
received.
Indicates the
NO NO Yes
received.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
transmitted.
Indicates the
LBFD-00300403 /
TDLBFD-00300403
transmitted.
Indicates the
NO NO Yes
transmitted.
Indicates the
master/slave flag of
LBFD-004002 /
the remote YES YES No
TDLBFD-004002
maintenance
channel.
Indicates the local

IP address of a
LBFD-004002 /
remote NO YES No
TDLBFD-004002
maintenance
channel.
Indicates the local
subnet mask of a
LBFD-004002 /
remote NO YES No
TDLBFD-004002
maintenance
channel.
Indicates the peer

IP address of the
remote
LBFD-004002 /
maintenance NO YES No
TDLBFD-004002
channel, that is, the
IP address of the
M2000.
Indicates the
subnet mask of the
peer IP address for LBFD-004002 /
NO YES No
the remote TDLBFD-004002
maintenance
channel.
Indicates the
cabinet number of
the board where the LBFD-004002 /
NO NO No
remote TDLBFD-004002
maintenance
channel is located.
Indicates the
subrack number of
NO NO No
maintenance
channel is located.
Indicates the slot
number of the
NO YES No
maintenance
channel is located.
Indicates the bearer
type of a remote LBFD-004002 /
NO NO No
maintenance TDLBFD-004002
channel.
Indicates whether
to add a route for
the remote
maintenance
channel. If this
parameter is set to
YES, a route is
automatically added
for the remote
maintenance
channel according
to the
configurations. If
this parameter is
set to NO,
operators must run
the ADD IPRT
LBFD-004002 /
command to NO NO No
TDLBFD-004002
manually add a
route for the remote
maintenance
channel when the
are met: The peer
IP address and the
device IP address
are not on the same
network segment
and the network
segment containing
the device IP
address does not
cover that
containing the peer
IP address.
Indicates the
destination IP
address used in the
routing table for a
remote
maintenance
LBFD-004002 /
channel. This IP NO YES No
TDLBFD-004002
address is a
Network ID, which
is usually the
address of the
network where the
M2000 is located.
Indicates the
subnet mask of the
destination IP
address used in the
routing table for a
LBFD-004002 /
remote NO YES No
TDLBFD-004002
maintenance
channel, that is, the
destination network
segment where the
EMS is located.
Indicates the type
of route in the
routing table for a
remote
maintenance
channel. LBFD-004002 /
NO NO No
set to NEXTHOP,
the next hop IP
address must be
specified in the
routing table.
Indicates the type

of egress port used
in the route for a LBFD-004002 /
NO YES No
maintenance
channel.
Indicates the
number of the
egress port used in
LBFD-004002 /
the route for a NO YES No
TDLBFD-004002
remote
maintenance
channel.
Indicates the
priority of the route
for the remote
maintenance
channel. The LBFD-004002 /
NO NO No
priority of the route TDLBFD-004002
has a negative
value of this
parameter.
Indicates the next
hop IP address of
the route added for LBFD-004002 /
NO YES No
a remote TDLBFD-004002
maintenance
channel.

of a remote LBFD-004002 /
NO NO Yes
channel.
Indicates whether
the remote
LBFD-004002 /
maintenance NO NO Yes
TDLBFD-004002
channel is being
used.
Indicates the type

of sub-board on the
board where a
LBFD-004002 /
remote NO YES No
TDLBFD-004002
maintenance
channel is
established.
Indicates the local

IPv6 address of a
remote LBFD-003006 /
YES YES No
channel. This LBFD-004002 /
global unicast
address.
Indicates the peer
IPv6 address of a
remote LBFD-003006 /
NO YES No
channel. This LBFD-004002 /
global unicast
address.

of an IPv6 remote TDLBFD-003006
NO NO Yes
maintenance LBFD-004002 /
channel. TDLBFD-004002
Indicates the
cabinet number of
LOFD-003014 /
TDLOFD-003014
packet filtering is
used.
Indicates the
subrack number of
LOFD-003014 /
TDLOFD-003014
packet filtering is
used.
Indicates the slot

number of the
LOFD-003014 /
TDLOFD-003014
packet filtering is
used.

YES YES No
of the port. TDLOFD-003014
YES YES No
number. TDLOFD-003014
Indicates the ID of
an advanced ACL.
LOFD-003014 /
The value of this NO YES No
TDLOFD-003014
parameter ranges
from 3000 to 3999.
Indicates whether
to permit or reject
access of the data
that does not match
the ACL rule. If this
parameter is set to
PERMIT, data that
LOFD-003014 /
does not match the NO NO No
TDLOFD-003014
ACL rule is allowed
to pass. If this
parameter is set to
DENY, data that
does not match the
ACL rule is
discarded.
Indicates the type
of sub-board on the LOFD-003014 /
YES YES No
board where packet TDLOFD-003014
filter is enabled.
Indicates the
number of
transmitted
LOFD-003014 /
packets. This NO NO Yes
TDLOFD-003014
parameter is
reserved for further
extension.
Indicates the
LOFD-003014 /
TDLOFD-003014
packets.
Indicates the
number of
permitted packets
LOFD-003014 /
on the TX channel. NO NO Yes
TDLOFD-003014
This parameter is
extension.
Indicates the
NO NO Yes
permitted packets TDLOFD-003014
on the RX channel.
Indicates the
number of rejected
packets on the TX
LOFD-003014 /
channel. This NO NO Yes
TDLOFD-003014
parameter is
extension.
Indicates the
number of rejected LOFD-003014 /
NO NO Yes
packets on the RX TDLOFD-003014
channel.
Indicates the
number of bytes
contained in
transmitted LOFD-003014 /
NO NO Yes
packets. This TDLOFD-003014
parameter is
extension.
Indicates the
number of bytes LOFD-003014 /
NO NO Yes
contained in TDLOFD-003014
received packets.
Indicates the
number of bytes
contained in
permitted packets LOFD-003014 /
NO NO Yes
on the TX channel. TDLOFD-003014
This parameter is
extension.
Indicates the
number of bytes
LOFD-003014 /
contained in NO NO Yes
TDLOFD-003014
permitted packets
on the RX channel.
Indicates the
number of bytes
contained in
rejected packets on LOFD-003014 /
NO NO Yes
the TX channel. TDLOFD-003014
This parameter is
extension.
Indicates the
number of bytes
LOFD-003014 /
contained in NO NO Yes
TDLOFD-003014
rejected packets on
the RX channel.
Indicates the
number of bytes
contained in the
packets that do not
match the ACL
rules for packet
filtering. If MB is set
to PERMIT, this
parameter
measures the
number of bytes
contained in the LOFD-003014 /
NO NO Yes
accessed packets. TDLOFD-003014
If MB is set to
DENY, this
parameter
measures the
number of bytes
contained in the
discarded packets.
This parameter is
valid only when
CATALOG is set to
PORT.
Indicates the
number of the
packets that do not
match the ACL
rules for packet
filtering. If MB is set
to PERMIT, this
parameter
measures the
number of
LOFD-003014 /
accessed packets. NO NO Yes
TDLOFD-003014
If MB is set to
DENY, this
parameter
measures the
number of
discarded packets.
This parameter is
valid only when
CATALOG is set to
PORT.
Indicates the ID of
an ACL at layer 2.
The value of this
parameter ranges LOFD-003014 /
NO YES No
from 4000 to 4999. TDLOFD-003014
The BS filters
packets based on
only VLAN IDs.
Indicates the packet
filtering mode. The
BS can filter
LOFD-003014 /
packets based on NO NO No
TDLOFD-003014
the advanced ACL,
layer-2 ACL, or both
at the same time.
Indicates the
destination IP
address in a ping
filter entry. This
YES YES No
valid IP address of TDLOFD-003014
class A, B, or C. It
can also be a
network segment
address.
Indicates the
subnet mask
corresponding to
LOFD-003014 /
the IP address in a YES YES No
TDLOFD-003014
ping filter entry. The
subnet mask
cannot be 0.0.0.0.
Indicates the PMTU

detection mode:
active or passive.
When this
parameter is set to
ACTIVE, PMTU
detection is
periodically
LBFD-003006 /
performed. When NO NO No
TDLBFD-003006
this parameter is
set to PASSIVE, the
PMTU is adjusted
according to the
ultra-large Internet
Control Message
Protocol (ICMP)
messages received.
Indicates the
destination port
number of the UDP
packets for PMTU
detection. Ports
65020, 65010,
LBFD-003006 /
65099, and 65100 NO NO No
TDLBFD-003006
are used for IP PM,
FPMUX, and AACP,
and therefore these
ports should not be
used for PMTU
detection.
Indicates the
timeout duration of LBFD-003006 /
NO NO No
a single PMTU TDLBFD-003006
detection.
Indicates the aging

LBFD-003006 /
period of the PMTU NO NO No
TDLBFD-003006
table.
Indicates the
default DSCP. If no
DSCP is specified
for a link, the
LBFD-003006 /
default DSCP is NO NO No
TDLBFD-003006
used when a PMTU
detection is
performed on the
link.
Indicates the
number of the
cabinet that houses LOFD-003014 /
YES NO No
the board where TDLOFD-003014
port security is
enabled.
Indicates the
number of the
subrack that LOFD-003014 /
YES NO No
houses the board TDLOFD-003014
where port security
is enabled.
Indicates the
number of the slot
corresponding to LOFD-003014 /
YES YES No
the board where TDLOFD-003014
port security is
enabled.
Indicates the type
of sub-board on the LOFD-003014 /
YES YES No
board where port TDLOFD-003014
security is enabled.
Indicates the type

of port on which LOFD-003014 /
YES NO No
port security is TDLOFD-003014
enabled.
Indicates the
number of the port
LOFD-003014 /
on which port YES YES No
TDLOFD-003014
security is
configured.
Indicates whether
to disable services
on a specified port
to implement port
security. If this
NO NO No
DISABLE, running TDLOFD-003014
services on the port
is prohibited,
thereby
guaranteeing the
security of the port.

cabinet number of TDLBFD-003004
YES NO No
PPP link is located. TDLBFD-00300402

subrack number of TDLBFD-003004
YES NO No
Indicates the slot LBFD-003004 /
number of the TDLBFD-003004
YES YES No
LBFD-003004 /
Indicates the
TDLBFD-003004
number of the PPP YES YES No
LBFD-00300402 /
link.
TDLBFD-00300402
Indicates the
LBFD-003004 /
number of the
TDLBFD-003004
ET/T1 port that NO YES No
LBFD-00300402 /
carries the PPP
TDLBFD-00300402
link.
Indicates the mode
in which the local
end of a PPP link
authenticates the
peer end. The
authentication
mode is classified
into NONAUTH,
PAP, and CHAP. In
PAP mode, user
names and
passwords are
transmitted
explicitly on the
network. If they are
intercepted during
transmission, a
LBFD-003004 /
great threat to
TDLBFD-003004
network security is NO NO No
LBFD-00300402 /
caused. Thus, the
TDLBFD-00300402
PAP is applied only
to the network
environment with
low security
requirements. With
three handshakes,
the CHAP provides
a more secure
authentication. In
CHAP mode, only
user accounts
rather than
passwords are
transmitted,
enhancing security
compared to the
PAP.
authentication user TDLBFD-003004
NO YES No
name of the PPP LBFD-00300402 /
link. TDLBFD-00300402
password for TDLBFD-003004
NO YES No
authenticating a LBFD-00300402 /
PPP link. TDLBFD-00300402
Indicates the
LBFD-003004 /
number of the
TDLBFD-003004
ET/T1 timeslot that NO YES No
LBFD-00300402 /
carries the PPP
TDLBFD-00300402
link.
Indicates the local
IP address. If this LBFD-003004 /
NO NO No
0.0.0.0, this LBFD-00300402 /
parameter needs to TDLBFD-00300402
be negotiated.
Indicates the
subnet mask of the
LBFD-003004 /
local IP address. If
TDLBFD-003004
LBFD-00300402 /
set to 0.0.0.0, it
TDLBFD-00300402
needs to be
negotiated.
Indicates the peer

IP address. If the
BS is connected to
an upper-level
node, this address
is specified LBFD-003004 /
according to the TDLBFD-003004
NO NO No
upper-level node. If LBFD-00300402 /
the BS is cascaded TDLBFD-00300402
to a lower-level
node, this address
must be specified.
This parameter can
be set to 0.0.0.0.
Indicates whether
to enable the PPP
multiframe
multiplexing
function. If this LBFD-003004 /
NO NO No
ENABLE, multiple LBFD-00300402 /
PPP frames are TDLBFD-00300402
multiplexed on the
PPP link to reduce
the bandwidth
overhead.
Indicates the
LBFD-003004 /
maximum length of
TDLBFD-003004
the PPP NO NO No
LBFD-00300402 /
Multiplexing (MUX)
TDLBFD-00300402
subframe.

maximum length of TDLBFD-003004
NO NO No
the PPP MUX LBFD-00300402 /
frame. TDLBFD-00300402
timeout duration of TDLBFD-003004
NO NO No
the PPP MUX LBFD-00300402 /
combination. TDLBFD-00300402
LBFD-003004 /
Indicates whether
TDLBFD-003004
to enable IP header NO NO No
LBFD-00300402 /
compression.
TDLBFD-00300402
Indicates the
Maximum Receive
Unit (MRU). If the LBFD-003004 /
size of a received TDLBFD-003004
NO NO No
packet is greater LBFD-00300402 /
than the MRU TDLBFD-00300402
value, the packet is
discarded.
LBFD-003004 /
Indicates whether
TDLBFD-003004
to enable protocol NO NO No
LBFD-00300402 /
field compression.
TDLBFD-00300402
Indicates whether
LBFD-003004 /
to enable the
TDLBFD-003004
compression of the NO NO No
LBFD-00300402 /
address field and
TDLBFD-00300402
control field.

timeout duration for TDLBFD-003004
NO NO No
the PPP link LBFD-00300402 /
negotiation. TDLBFD-00300402
LBFD-003004 /
Indicates the status TDLBFD-003004
NO NO Yes
of the PPP link. LBFD-00300402 /
TDLBFD-00300402

of the Link Control TDLBFD-003004
NO NO Yes
Protocol (LCP) LBFD-00300402 /
protocol. TDLBFD-00300402
LBFD-003004 /
TDLBFD-003004
of the IP Control NO NO Yes
LBFD-00300402 /
Protocol (IPCP).
TDLBFD-00300402
LBFD-003004 /
Indicates the status TDLBFD-003004
NO NO Yes
of the PPP MUX. LBFD-00300402 /
TDLBFD-00300402
Indicates the local LBFD-003004 /

IP address TDLBFD-003004
NO NO Yes
negotiated with the LBFD-00300402 /
peer end. TDLBFD-00300402
Indicates the mask
LBFD-003004 /
of the local IP
TDLBFD-003004
address that is NO NO Yes
LBFD-00300402 /
negotiated with the
TDLBFD-00300402
peer end.
IP address TDLBFD-003004
NO NO Yes
negotiated with the LBFD-00300402 /
peer end. TDLBFD-00300402
negotiation result of TDLBFD-003004
NO NO Yes
the IP header LBFD-00300402 /
compression. TDLBFD-00300402
Indicates the
the compression TDLBFD-003004
NO NO Yes
switch of the LBFD-00300402 /
address field and TDLBFD-00300402
control field.
Indicates the
LBFD-003004 /
negotiation result of
TDLBFD-003004
the compression NO NO Yes
LBFD-00300402 /
switch of the
TDLBFD-00300402
protocol field.
negotiation result of TDLBFD-003004
NO NO Yes
the maximum RX LBFD-00300402 /
unit. TDLBFD-00300402
LBFD-003004 /
Indicates the
TDLBFD-003004
LBFD-00300402 /
the PPP MUX.
TDLBFD-00300402
number of packets TDLBFD-003004
NO NO Yes
received on the LBFD-00300402 /
number of packets TDLBFD-003004
NO NO Yes
transmitted on the LBFD-00300402 /
LBFD-003004 /
Indicates the RX
TDLBFD-003004
traffic of the PPP NO NO Yes
LBFD-00300402 /
link.
TDLBFD-00300402
LBFD-003004 /
Indicates the TX
TDLBFD-003004
traffic of the PPP NO NO Yes
LBFD-00300402 /
link.
TDLBFD-00300402
number of IP TDLBFD-003004
NO NO Yes
addresses of the LBFD-00300402 /
LBFD-003004 /
TDLBFD-003004
IP addresses of the NO NO Yes
LBFD-00300402 /
PPP link.
TDLBFD-00300402
Indicates the PPP
LBFD-003004 /
frame error rate
TDLBFD-003004
threshold above NO NO No
LBFD-00300402 /
which the related
TDLBFD-00300402
alarm is generated.
Indicates the PPP
LBFD-003004 /
frame error rate
TDLBFD-003004
threshold below NO NO No
LBFD-00300402 /
which the related
TDLBFD-00300402
alarm is cleared.
Indicates the type LBFD-003004 /

of sub-board on the TDLBFD-003004
YES YES No
board where a PPP LBFD-00300402 /
link is located. TDLBFD-00300402

number of bytes TDLBFD-003004
NO NO Yes
received on the LBFD-00300402 /
Indicates the
LBFD-003004 /
number of
TDLBFD-003004
LBFD-00300402 /
received on the
TDLBFD-00300402
PPP link.
number of bytes TDLBFD-003004
NO NO Yes
transmitted on the LBFD-00300402 /
Indicates the
LBFD-003004 /
number of
TDLBFD-003004
LBFD-00300402 /
transmitted on the
TDLBFD-00300402
PPP link.
Indicates the lowest

priority of queue 0.
If the Differentiated
Services Code
Point (DSCP) value
of a service packet LBFD-00300201 /
NO NO No
is greater than or TDLBFD-00300201
equal to this
parameter value,
the service packet
is assigned to
queue 0.

If the DSCP value
of a service packet
is smaller than the
PRI0 value but LBFD-00300201 /
NO NO No
greater than or TDLBFD-00300201
equal to this
parameter value,
the service packet
is assigned to
queue 1.
If the DSCP value
of a service packet
is smaller than the
NO NO No
equal to this
parameter value,
the service packet
is assigned to
queue 2.

If the DSCP value
of a service packet
is smaller than the
NO NO No
equal to this
parameter value,
the service packet
is assigned to
queue 3.

If the DSCP value
of a service packet
is smaller than the
NO NO No
equal to this
parameter value,
the service packet
is assigned to
queue 4.
If the DSCP value
of a service packet
is smaller than the
NO NO No
equal to this
parameter value,
the service packet
is assigned to
queue 5.

If the DSCP value
of a service packet
is smaller than the
NO NO No
equal to this
parameter value,
the service packet
is assigned to
queue 6.
Indicates the
number of the
cabinet that houses
LOFD-003011 /
the board where a YES NO No
TDLOFD-003011
transmission
resource group is
established.
Indicates the
number of the
subrack that
houses the board LOFD-003011 /
YES NO No
where a TDLOFD-003011
transmission
resource group is
established.
Indicates the
number of the slot
corresponding to
LOFD-003011 /
the board where a YES YES No
TDLOFD-003011
transmission
resource group is
established.
Indicates the bearer

type of a LOFD-003011 /
YES YES No
resource group.
Indicates the type

of sub-board on the
YES YES No
resource group is
established.
Indicates the type

of port where a
LOFD-003011 /
transmission YES YES No
TDLOFD-003011
resource group is
carried.
Indicates the
number of the port
where a LOFD-003011 /
YES NO No
resource group is
carried.
transmission
resource group.
When you add a
PPP link, an MP
group, an Ethernet
port, an Ethernet
trunk, or a tunnel,
the system
automatically
creates an
algorithm for the
transmission
resource group with YES YES No None
Transmission
Resource Group ID
set to
DEFAULTPORT(De
fault Port). When
you remove any of
the preceding
objects, the system
automatically
removes the
algorithm for the
transmission
resource group.
Indicates the rate

unit of the TX
bandwidth, RX
bandwidth, TX CIR, LOFD-003011 /
NO NO No
RX CIR, TX PIR TDLOFD-003011
and RX PIR of the
transmission
resource group.
Indicates the
maximum uplink
bandwidth of a
transmission
resource group at
the MAC layer
when the
NO YES No
carried over IP. This
parameter value is
used as the uplink
transport admission
bandwidth and TX
traffic shaping
bandwidth.
Indicates the RX
bandwidth of a LOFD-003011 /
NO YES No
resource group.
Indicates the TX
committed burst
LOFD-003011 /
size of a NO NO No
TDLOFD-003011
transmission
resource group.
Indicates the TX
excessive burst size LOFD-003011 /
NO NO No
of a transmission TDLOFD-003011
resource group.
Indicates the index

of the operator. This
parameter is used
to differentiate
between operators. LOFD-003011 /
NO NO No
This parameter is TDLOFD-003011
reserved for future
extension and does
not take effect
currently.
Indicates the
scheduling weight
of a transmission
resource group.
This parameter is
used in calculating LOFD-003011 /
NO NO No
the bandwidth TDLOFD-003011
scheduled to a
resource group,
which helps
achieve the user
admission control.
Indicates the
transmit CIR of the LOFD-003011 /
NO YES No
resource group.
Indicates the
receive CIR of the LOFD-003011 /
NO YES No
resource group.
Indicates the
transmit PIR of the LOFD-003011 /
NO YES No
resource group.
Indicates the
receive PIR of the LOFD-003011 /
NO YES No
resource group.

the peak burst
LOFD-003011 /
transmitted from the NO YES No
TDLOFD-003011
transmission
resource group.
Indicates the local
real-time traffic that
is transmitted in a
transmission
resource group.
The local traffic LOFD-003011 /
NO NO Yes
includes only the TDLOFD-003011
local traffic stream
exclusive of the
passing-by data
flow and non-traffic
stream.
Indicates the local
real-time traffic that
is received in a
transmission
resource group.
NO NO Yes
exclusive of the
passing-by data
stream.
Indicates the local
that is transmitted
in a transmission
resource group.
NO NO Yes
exclusive of the
passing-by data
stream.
Indicates the local
that is received in a
transmission
resource group.
NO NO Yes
exclusive of the
passing-by data
stream.
Indicates the TX
bandwidth reserved
for non-real-time LOFD-003011 /
NO NO Yes
services in a TDLOFD-003011
transmission
resource group.
Indicates the RX
bandwidth reserved
for non-real-time LOFD-003011 /
NO NO Yes
services in a TDLOFD-003011
transmission
resource group.
Indicates the GBR
service traffic that is
LOFD-003011 /
transmitted by the NO NO Yes
TDLOFD-003011
transmission
resource group.
Indicates the GBR
service traffic
LOFD-003011 /
received by the NO NO Yes
TDLOFD-003011
transmission
resource group.
Indicates the rate
configuration mode LOFD-003011 /
NO NO Yes
of the transmission TDLOFD-003011
resource group.
admission
LOFD-003011 /
bandwidth of the NO NO Yes
TDLOFD-003011
transmission
resource group.
Indicates the
downlink admission
LOFD-003011 /
TDLOFD-003011
transmission
resource group.
Indicates the UL
Committed
Information Rate
LOFD-003011 /
(CIR) admission NO NO Yes
TDLOFD-003011
bandwidth for the
transmission
resource group.
Indicates the CIR

admission
NO NO Yes
resource group in
DL.
Indicates the UL
PIR admission
LOFD-003011 /
TDLOFD-003011
transmission
resource group.
Indicates the PIR
admission
NO NO Yes
resource group in
DL.
Indicates the
realtime traffic sent LOFD-003011 /
NO NO Yes
on a transmission TDLOFD-003011
resource group.
Indicates the
LOFD-00301101 /
number of the
TDLOFD-00301101
cabinet that houses
LOFD-00301102 /
the board where a YES NO No
TDLOFD-00301102
transmission
LOFD-00301103 /
resource group is
TDLOFD-00301103
established.
Indicates the
subrack that TDLOFD-00301101
houses the board LOFD-00301102 /
YES NO No
where a TDLOFD-00301102
established.
Indicates the
LOFD-00301101 /
number of the slot
TDLOFD-00301101
corresponding to
LOFD-00301102 /
the board where a YES YES No
TDLOFD-00301102
transmission
LOFD-00301103 /
resource group is
TDLOFD-00301103
occupied.

of sub-board on the TDLOFD-00301101
YES YES No
resource group is LOFD-00301103 /
established. TDLOFD-00301103
LOFD-00301101 /
Indicates the type
TDLOFD-00301101
of port on which a
LOFD-00301102 /
transmission YES YES No
TDLOFD-00301102
resource group is
LOFD-00301103 /
carried.
TDLOFD-00301103
number of the port TDLOFD-00301101
on which a LOFD-00301102 /
YES NO No
resource group is LOFD-00301103 /
carried. TDLOFD-00301103
transmission
resource group.
When you add a
PPP link, an MP
group, an Ethernet
port, an Ethernet
trunk, or a tunnel,
the system
automatically
LOFD-00301101 /
creates a
TDLOFD-00301101
transmission
LOFD-00301102 /
resource group with YES YES No
TDLOFD-00301102
Transmission
LOFD-00301103 /
Resource Group ID
TDLOFD-00301103
set to
DEFAULTPORT(De
fault Port). When
you remove any of
the preceding
objects, the system
automatically
removes the
transmission
resource group.
Indicates whether
to enable traffic
shaping for a
transmission
resource group.
set to ON, traffic
shaping is
performed
according to the TX
LOFD-00301101 /
bandwidth so that
TDLOFD-00301101
the transmit traffic
LOFD-00301102 /
would not exceed NO NO No
TDLOFD-00301102
the capability of
LOFD-00301103 /
downstream
TDLOFD-00301103
routers, thus
avoiding
unnecessary packet
loss and
congestion.
set to OFF, traffic
shaping is not
performed during
data transmission.
Indicates whether
to enable the
dynamic adjustment
of the RX
bandwidth of a
transmission
resource group.
set to ON, the TX
bandwidth is
adjusted according
to the network
performance and
dynamic bandwidth LOFD-00301101 /
adjustment TDLOFD-00301101
parameters (down LOFD-00301102 /
NO NO No
speed PLR TDLOFD-00301102
threshold and down LOFD-00301103 /
speed delay TDLOFD-00301103
threshold). The
network
performance is
monitored through
IP PM sessions,
which can be
enabled at the local
end or at the peer
end.
set to OFF, the TX
bandwidth is not
adjusted.
Indicates whether
to enable the
dynamic adjustment
of the RX
bandwidth of a
transmission
resource group.
set to ON, the RX
bandwidth is
adjusted according
to the network
performance and
dynamic bandwidth LOFD-00301101 /
adjustment TDLOFD-00301101
parameters (down LOFD-00301102 /
NO NO No
speed PLR TDLOFD-00301102
threshold and down LOFD-00301103 /
speed delay TDLOFD-00301103
threshold). The
network
performance is
monitored through
IP PM sessions,
which can be
enabled at the local
end or at the peer
end.
set to OFF, the RX
bandwidth is not
adjusted.
Indicates the rate

downsizing packet
loss rate threshold
for bandwidth
adjustment. When
RXBWASW or
TXBWASW is set to
ON, the estimated
available transport
bandwidth is LOFD-00301101 /
reduced if the TDLOFD-00301101
packet loss rate LOFD-00301102 /
NO NO No
detected through IP TDLOFD-00301102
Performance LOFD-00301103 /
Monitoring (IP PM) TDLOFD-00301103
is higher than this
threshold. If the
packet loss rate
detected through IP
PM is lower than
this threshold, the
estimated available
transport bandwidth
is increased.
Indicates the
threshold for delay
variation due to rate
reduction. When
RXBWASW or LOFD-00301101 /
TXBWASW is set to TDLOFD-00301101
ON, the estimated LOFD-00301102 /
NO NO No
available transport TDLOFD-00301102
bandwidth is LOFD-00301103 /
reduced if the delay TDLOFD-00301103
variation detected
by an IP PM
session is above
this threshold.
Indicates the
minimum TX
bandwidth that
adjustments can
achieve. If the
RATECFGTYPE
(global rate
configuration type)
LOFD-00301101 /
and TXBWASW (TX
TDLOFD-00301101
bandwidth
LOFD-00301102 /
adjustment switch) NO NO No
TDLOFD-00301102
parameters are set
LOFD-00301103 /
to SINGLE_RATE
TDLOFD-00301103
and ON,
respectively, the TX
bandwidth obtained
after each
adjustment is equal
to or larger than the
value of this
parameter.
Indicates the
minimum RX
bandwidth that
adjustments can
achieve. If the
RATECFGTYPE
(global rate
configuration type)
LOFD-00301101 /
and RXBWASW
TDLOFD-00301101
(RX bandwidth
LOFD-00301102 /
adjustment switch) NO NO No
TDLOFD-00301102
parameters are set
LOFD-00301103 /
to SINGLE_RATE
TDLOFD-00301103
and ON,
respectively, the RX
bandwidth obtained
after each
adjustment is equal
to or larger than the
value of this
parameter.
the data buffered in

the queues of each
transmission
resource group,
determines whether
the transmission
resource group is
congested, and
transmits the
backpressure
signals (number
and congestion
status of the
transmission
resource group) to
each flow control
LOFD-00301101 /
service.
TDLOFD-00301101
If the number of
LOFD-00301102 /
data packets in the NO NO No
TDLOFD-00301102
buffer of any
LOFD-00301103 /
backpressure
TDLOFD-00301103
queue exceeds
75% of the queue
capacity, the BS
regards this
transmission
resource group as
congested and
transmits
congestion signals.
If the buffered back-
pressure packets
are less than 50%
of the total buffer
capacity, the BS
decides that the
transmission
performed on the
OM FTP queue in a
transmission
resource group. If
this parameter is
set to ENABLE, the
OM FTP queue
participates the
decision of the
congestion status of
the transmission
resource group,
and the OM low-
level upload and
download data
preempts the
LOFD-00301101 /
bandwidth of non-
TDLOFD-00301101
real-time services. If
LOFD-00301102 /
TDLOFD-00301102
set to DISABLE, the
LOFD-00301103 /
OM FTP queue
TDLOFD-00301103
does not participate
the decision of the
congestion status of
the transmission
resource group,
and the OM low-
level upload and
download data
does not preempt
the bandwidth of
non-real-time
services. The
bandwidth of OM
low-level upload
and download data
is far smaller than
Indicates the
number of Priority
Queues (PQs) in a
transmission
resource group.
The queues in a
transmission
resource group are
classified into PQs
and non-PQs. The
scheduling priority
of any PQ is higher
than that of any
non-PQ. There is
no Priority Queues
LOFD-00301101 /
when this
TDLOFD-00301101
parameter value is
LOFD-00301102 /
0.The queues NO NO No
TDLOFD-00301102
numbered from 0 to
LOFD-00301103 /
the result after this
TDLOFD-00301103
parameter value
minus 1 are PQs.
PQ scheduling is
used between PQs.
A smaller PQ
number indicates a
higher scheduling
priority. The queues
numbered from this
parameter value to
6 are non-PQs.
Weight Round
Robin (WPR)
scheduling is used
between non-PQs.
Indicates the
congestion time
threshold of a
transmission
resource group.
When TCSW is set
to ENABLE, if the
buffer time of non-
LOFD-00301101 /
real-time service
TDLOFD-00301101
data in a
LOFD-00301102 /
transmission NO NO No
TDLOFD-00301102
resource group
LOFD-00301103 /
exceeds the
TDLOFD-00301103
threshold, it
indicates that the
transmission
resource group is
congested and the
backpressure
signals are
transmitted.
Indicates the
congestion clear
time threshold of a
transmission
resource group.
When TCSW is set
to ENABLE, if the
buffer time of non-
real-time service LOFD-00301101 /
data in a TDLOFD-00301101
NO NO No
below the LOFD-00301103 /
threshold, it TDLOFD-00301103
indicates that the
transmission
resource group is
not congested and
therefore the
congestion clear
signals are
transmitted.
Indicates the TX
bandwidth reserved
for signaling or OM
data. This
parameter should
be set to a value
LOFD-00301101 /
smaller than the TX
TDLOFD-00301101
bandwidth of a
LOFD-00301102 /
transmission NO NO No
TDLOFD-00301102
resource group.
LOFD-00301103 /
The recommended
TDLOFD-00301103
reserved TX
bandwidth is lower
than or equal to 3%
of the TX bandwidth
of a transmission
resource group.
Indicates the
reserved RX
LOFD-00301101 /
bandwidth, which
TDLOFD-00301101
should be set to a
LOFD-00301102 /
value smaller than NO NO No
TDLOFD-00301102
or equal to the RX
LOFD-00301103 /
bandwidth of a
TDLOFD-00301103
transmission
resource group.
capability of the
queue in a
transmission
resource group to
buffer packets. A
greater parameter
value indicates a
stronger capability.
set to 0, the queue
in a transmission
resource group
cannot buffer
packets, and thus
all the delayed
packets on the TX
channel are LOFD-00301101 /
discarded. The TDLOFD-00301101
number threshold of LOFD-00301102 /
NO NO No
discarded packets TDLOFD-00301102
determines the LOFD-00301103 /
maximum amount TDLOFD-00301103
of data that can be
buffered in a
transmission
resource group.
The congestion
time threshold of a
transmission
resource group
determines the
amount of data that
is buffered when
the transmission
resource group is
congested. Ensure
that the maximum
amount of data that
Indicates the
SCTP link.
Indicates the
cabinet number of NO NO No None
the SCTP link.
Indicates the
subrack number of NO NO No None
the SCTP link.
Indicates the slot
number of the NO YES No None
SCTP link.
Indicates the
maximum stream
NO NO No None
number of the
SCTP link.
Indicates the first

local IP address of NO YES No None
the SCTP link.
Indicates the
second local IP
NO NO No None
address of the
SCTP link.
Indicates the local

port number of the NO YES No None
SCTP link.
Indicates the first

peer IP address of NO YES No None
the SCTP link.
Indicates the
second peer IP
NO NO No None
address of the
SCTP link.
Indicates the peer

port number of the NO YES No None
SCTP link.
Indicates the
minimum
Retransmission
Timeout (RTO)
value for the SCTP
link. A smaller value
of this parameter
indicates a shorter
time required to
check link
connectivity. The NO NO No None
time required to
check link
connectivity is twice
the sum of the new
RTO and heartbeat
interval. The new
RTO ranges from
the minimum RTO
value to maximum
RTO value.
Indicates the
maximum RTO
value of an SCTP
link. A larger value
NO NO No None
indicates a longer
period required for
checking link
connectivity.
RTO value of an
SCTP link. A larger
value indicates a
NO NO No None
longer period
required for
checking link
connectivity.
a higher importance
to the last RTT
measurement. For
definitions of the
alpha value, see
RFC4960.
RTO Calculation:
The rules governing
the computation of
SRTT, RTTVAR,
and RTO are as
follows:
1) Until an RTT
measurement has
been made for a
packet sent to the
given destination
transport address,
set RTO to the NO NO No None
protocol parameter
'RTO.Initial'.
2) When the first
RTT measurement
R is made, set
SRTT = R, RTTVAR
= R/2, and RTO =
SRTT + 4 *
RTTVAR.
3) When a new RTT
measurement R' is
made, set RTTVAR
= (1 - RTO.Beta) *
RTTVAR +
RTO.Beta * |SRTT -
R'|, SRTT = (1 -
RTO.Alpha) * SRTT
+ RTO.Alpha * R'.
a higher importance
to the last RTT
measurement. For
definitions of the
beta value, see
RFC4960.
RTO Calculation:
The rules governing
the computation of
SRTT, RTTVAR,
and RTO are as
follows:
1) Until an RTT
measurement has
been made for a
packet sent to the
given destination
transport address,
set RTO to the NO NO No None
protocol parameter
'RTO.Initial'.
2) When the first
RTT measurement
R is made, set
SRTT = R, RTTVAR
= R/2, and RTO =
SRTT + 4 *
RTTVAR.
3) When a new RTT
measurement R' is
made, set RTTVAR
= (1 - RTO.Beta) *
RTTVAR +
RTO.Beta * |SRTT -
R'|, SRTT = (1 -
RTO.Alpha) * SRTT
+ RTO.Alpha * R'.
Indicates the
heartbeat interval
for an SCTP link.
The heartbeat
check is
independently
initiated by each
end of an
association and
then confirmed by
the peer end
through the HB
ACK packet. When
no services are NO NO No None
carried, a link
disconnection is
determined if the
number of
heartbeat check
attempts reaches
the maximum
retransmission
attempts on an
association but the
HB ACK packet is
not received from
the peer end.
Indicates the
maximum number
of retransmissions
for the SCTP
association. When
the number of
retransmissions for
NO NO No None
the association
exceeds the value
of this parameter,
the SCTP link is
broken and a link
failure alarm is
reported.
Indicates the
maximum number
of retransmissions
over a path. When
the number of
retransmissions
over a path
exceeds the value
of this parameter,
NO NO No None
the path is regarded
as failed if no
heartbeat
acknowledgment is
paths are used,
path switching is
automatically
performed.
Indicates whether
to calculate the
checksum of the
data to be sent.
This parameter will
be removed in later
versions. In this
NO NO No None
still synchronized
between the M2000
and the BS, but it is
always set to
ENABLE internally.
Therefore, avoid
setting this
parameter to
DISABLE.
Indicates whether
to check the
checksum of the
packet that is
received. This
parameter will be
removed in later
versions. In this
of this parameter is NO NO No None
still synchronized
between the M2000
and the BS, but it is
always set to
ENABLE internally.
Therefore, avoid
setting this
parameter to
DISABLE.
Indicates the
checksum NO NO No None
algorithm.
Indicates whether
to switch back to
the primary path
when it is restored.
The SCTP link
switches to the
secondary path
when the primary
path cannot be
reached. If this
parameter is set to
ENABLE, the SCTP NO NO No None
link switches to the
primary path when
the primary path is
restored. If this
parameter is set to
DISABLE, the
SCTP link does not
switch to the
primary path when
the primary path is
restored.
Indicates the
number of
heartbeats to be
detected before the
transmission
switches back to
the primary path.
After the primary NO NO No None
path is restored, the
transmission
switches back to
the primary path
when the number of
heartbeats detected
reaches this value.

NO NO Yes None
of the SCTP link.
Indicates the cause
of the latest change
that the operational
state of the SCTP NO NO Yes None
link transits from
available to
unavailable.
Indicates the time

that the operational
state of the SCTP NO NO Yes None
link transits from
available to
unavailable.
Indicates the
number of
outbound streams NO NO Yes None
negotiated for the
SCTP link.
Indicates the
number of inbound
NO NO Yes None
streams negotiated
for the SCTP link.
Indicates the
working address
NO NO Yes None
flag of the SCTP
link.
Indicates whether
the SCTP link is NO NO No None
blocked or not.
Indicates the time
interval that one
end of an SCTP link
can send an SACK
message in
response to the
reception of data. A
larger value of this NO NO No None
parameter indicates
a longer time
interval between
the reception of
data and the
sending of the
corresponding
SACK message.
Indicates the peer

description
NO NO No None
information of the
SCTP link.
LBFD-003006 /
Indicates the
TDLBFD-003006
number of an IPv6 YES YES No
LOFD-003017 /
SCTP link.
TDLOFD-003017
Indicates the
LBFD-003006 /
number of streams
TDLBFD-003006
supported NO NO No
LOFD-003017 /
simultaneously by
TDLOFD-003017
an IPv6 SCTP link.
Indicates the first LBFD-003006 /

local IPv6 address TDLBFD-003006
NO YES No
of an IPv6 SCTP LOFD-003017 /
link. TDLOFD-003017
second local IPv6 TDLBFD-003006
NO NO No
address of an IPv6 LOFD-003017 /
SCTP link. TDLOFD-003017
Indicates the local

SCTP port number
of the IPv6 SCTP
link. This parameter
LBFD-003006 /
must be set to the
TDLBFD-003006
same value as that NO YES No
LOFD-003017 /
of the peer SCTP
TDLOFD-003017
port number in the
IPv6 SCTP link
configured at the
peer end.
Indicates the first LBFD-003006 /

peer IPv6 address TDLBFD-003006
NO YES No
of an IPv6 SCTP LOFD-003017 /
link. TDLOFD-003017
second peer IPv6 TDLBFD-003006
NO NO No
address of an IPv6 LOFD-003017 /
Indicates the peer

SCTP port number
of the IPv6 SCTP
link. This parameter
LBFD-003006 /
must be set to the
TDLBFD-003006
same value as that NO YES No
LOFD-003017 /
of the local SCTP
TDLOFD-003017
port number in the
IPv6 SCTP link
configured at the
peer end.
Indicates the
minimum
Retransmission
Timeout (RTO)
LBFD-003006 /
value for the SCTP
TDLBFD-003006
IPv6 link. A smaller NO NO No
LOFD-003017 /
value of this
TDLOFD-003017
parameter indicates
a shorter time
required to check
link connectivity.
Indicates the
maximum RTO
value of an IPv6
LBFD-003006 /
SCTP link. A larger
TDLBFD-003006
value indicates a NO NO No
LOFD-003017 /
longer period
TDLOFD-003017
required for
checking link
connectivity.
RTO value of an
IPv6 SCTP link. A LBFD-003006 /
larger value TDLBFD-003006
NO NO No
indicates a longer LOFD-003017 /
period required for TDLOFD-003017
checking link
connectivity.
Indicates the RTO
alpha value of an
NO NO No
indicates less LOFD-003017 /
sensitivity to the link TDLOFD-003017
delay. For details,
see RFC4960.
Indicates the RTO
beta value of an
NO NO No
indicates less LOFD-003017 /
sensitivity to the link TDLOFD-003017
delay. For details,
see RFC4960.
Indicates the
heartbeat interval
for an IPv6 SCTP
link. The heartbeat
check is
independently
initiated by each
end of an
association and
then confirmed by
the peer end
through the HB
LBFD-003006 /
ACK packet
TDLBFD-003006
indicating normal NO NO No
LOFD-003017 /
link connection.
TDLOFD-003017
If the number of
heartbeat check
attempts reaches
the maximum
retransmission
attempts on an
association but the
HB ACK packet is
not received from
the peer end, a link
disconnection is
determined.
Indicates the
maximum number
of association
retransmissions on
the IPv6 SCTP link.
LBFD-003006 /
If the number of
TDLBFD-003006
retransmissions NO NO No
LOFD-003017 /
exceeds the value
TDLOFD-003017
of this parameter,
the SCTP link is
broken and a link
failure alarm is
reported.
Indicates the
maximum number
of retransmissions
over a path of the
IPv6 SCTP link. If
no heartbeat
response is
received when the
number of
LBFD-003006 /
retransmissions
TDLBFD-003006
over a path NO NO No
LOFD-003017 /
exceeds the value
TDLOFD-003017
of this parameter, it
indicates that the
current path cannot
be reached. If
multiple paths are
used on the IPv6
SCTP link, path
switching is
performed.
LBFD-003006 /
Indicates the
TDLBFD-003006
checksum NO NO No
LOFD-003017 /
arithmetic.
TDLOFD-003017
Indicates whether
to switch back to
the primary path
when the primary
path is restored.
The IPv6 SCTP link
switches to the
secondary path LBFD-003006 /
when the primary TDLBFD-003006
NO NO No
path cannot be LOFD-003017 /
reached. This TDLOFD-003017
parameter is used
to set whether an
IPv6 SCTP link
switches back to
the primary path
when the primary
path is restored.
Indicates the
number of
heartbeats that are
detected before
transmission
smoothly switches
back from the
associated
secondary path to
the primary path.
After the associated LBFD-003006 /
primary path is TDLBFD-003006
NO NO No
restored, LOFD-003017 /
smoothly switches
back from the
secondary path to
the primary path
when the number of
detected
successive
heartbeats reaches
this parameter
value.
LBFD-003006 /
TDLBFD-003006
of the IPv6 SCTP NO NO Yes
LOFD-003017 /
link.
TDLOFD-003017
Indicates the cause

LBFD-003006 /
of the operational
TDLBFD-003006
state of an IPv6 NO NO Yes
LOFD-003017 /
SCTP link from
TDLOFD-003017
available to
unavailable.
Indicates the last
time when the
LBFD-003006 /
TDLBFD-003006
an IPv6 SCTP link NO NO Yes
LOFD-003017 /
changes from
TDLOFD-003017
available to
unavailable.
Indicates the
LBFD-003006 /
number of TX
TDLBFD-003006
streams negotiated NO NO Yes
LOFD-003017 /
for an IPv6 SCTP
TDLOFD-003017
link.
Indicates the
LBFD-003006 /
number of RX
TDLBFD-003006
streams negotiated NO NO Yes
LOFD-003017 /
for an IPv6 SCTP
TDLOFD-003017
link.
working address TDLBFD-003006
NO NO Yes
flag of an IPv6 LOFD-003017 /
LBFD-003006 /
Indicates whether
TDLBFD-003006
the IPv6 SCTP link NO NO No
LOFD-003017 /
is blocked.
TDLOFD-003017
description TDLBFD-003006
NO NO No
information of an LOFD-003017 /
IPv6 SCTP link. TDLOFD-003017
Indicates the
source or
LBFD-003003 /
destination IP YES YES No
TDLBFD-003003
address used for
mapping the VLAN.
Indicates the
subnet mask of the
source or LBFD-003003 /
YES YES No
destination IP TDLBFD-003003
address used for
mapping the VLAN.
Indicates the VLAN LBFD-003003 /

NO YES No
ID in the VLAN tag. TDLBFD-003003
that is used to
control whether to LOFD-00301101 /
NO NO No
apply UL admission TDLOFD-00301101
control to a
resource group.

that is used to
control whether to LOFD-00301101 /
NO NO No
apply DL admission TDLOFD-00301101
control to a
resource group.
Indicates the
activity factor of the
service data with LOFD-00301101 /
QoS Class Indicator TDLOFD-00301101
(QCI) of 1. The LOFD-00301103 /
activity factor must TDLOFD-00301103
NO NO No
be set for the LOFD-003016 /
service with each TDLOFD-003016
QCI, because LOFD-001032 /
services of different TDLOFD-001032
QCIs experience
different loads.
LOFD-00301101 /
TDLOFD-00301101
activity factor of the TDLOFD-00301103
NO NO No
service data of QCI LOFD-003016 /
2. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
3. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
4. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
5. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
6. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
7. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
8. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
LOFD-00301101 /
TDLOFD-00301101
NO NO No
9. TDLOFD-003016
LOFD-001032 /
TDLOFD-001032
Indicates the UL
admission threshold
for handed-over
services. A large
NO NO No
parameter will result TDLOFD-00301101
in a high UL
admission success
rate of handed-over
services.
Indicates the DL
admission threshold
for handed-over
services. A large
NO NO No
in a high DL
admission success
rate of handed-over
services.
Indicates the UL
admission threshold
for new Gold-level
services. A large
NO NO No
in a high UL
admission success
rate of new Gold-
level services.
Indicates the DL
admission threshold
for new Gold-level
services. A large
NO NO No
in a high DL
admission success
rate of new Gold-
level services.
Indicates the UL
admission threshold
for new Silver-level
services. A large
NO NO No
in a high UL
admission success
rate of new Silver-
level services.
Indicates the DL
admission threshold
for new Silver-level
services. A large
NO NO No
in a high DL
admission success
rate of new Silver-
level services.
Indicates the UL
admission threshold
for new Copper-
level services. A
large value of this LOFD-00301101 /
NO NO No
parameter will TDLOFD-00301101
results in a high UL
admission success
rate of new Copper-
level services.
Indicates the DL
admission threshold
for new Copper-
level services. A
large value of this LOFD-00301101 /
NO NO No
in a high DL
admission success
rate of new Copper-
level services.
transport admission
threshold for the
Guaranteed the Bit
Rate (GBR) service.
LOFD-00301101 /
A large value of this NO NO No
TDLOFD-00301101
parameter will result
in a high UL
admission success
rate of GBR
services.
Indicates the DL
admission threshold
for the guaranteed
bit rate (GBR)
service. A large
LOFD-00301101 /
TDLOFD-00301101
parameter will result
in a high DL
admission success
rate of GBR
services.
that is used to
control whether to
enable the UL pre-
emption algorithm.
set to ON, the UL
pre-emption
algorithm is
enabled. In this
case, the service
that requests
admission may pre-
empt the resources
of admitted services
with lower priorities
when UL LOFD-00301101 /
NO NO No
bandwidth is
insufficient. If this
parameter is set to
OFF, the UL pre-
emption algorithm is
disabled. In this
case, services with
higher priorities that
request admission
cannot pre-empt
the resources of
admitted services
when UL
transmission
bandwidth is
insufficient.
that is used to
control whether to
enable the DL pre-
emption algorithm.
set to ON, the DL
pre-emption
algorithm is
enabled. In this
case, the service
that requests
admission can pre-
empt the resources
of admitted services
when DL LOFD-00301101 /
NO NO No
bandwidth is
insufficient. If this
parameter is set to
OFF, the DL pre-
emption algorithm is
disabled. In this
case, services with
higher priorities that
request admission
cannot pre-empt
the resources of
admitted services
when DL
transmission
bandwidth is
insufficient.
that is used to
control whether to
enable UL
overbooking
admission control. It
LOFD-00301101 /
is used to NO NO No
TDLOFD-00301101
determine the
admission
bandwidth of the
resource group and
facilitate admission
control.
that is used to
control whether to
enable DL
overbooking
admission control. It
LOFD-00301101 /
is used to NO NO No
TDLOFD-00301101
determine the
admission
bandwidth of the
resource group and
facilitate admission
control.

that is used to
control whether to
apply UL admission
control to a physical
port. If this
parameter is set to
LOFD-00301101 /
ON, UL admission NO NO No
TDLOFD-00301101
control is applied to
the physical port. If
this parameter is
set to OFF, UL
admission control is
not applied to the
physical port.
that is used to
control whether to
apply DL admission
control to a physical
port. If this
parameter is set to
LOFD-00301101 /
ON, DL admission NO NO No
TDLOFD-00301101
control is applied to
the physical port. If
this parameter is
set to OFF, DL
admission control is
not applied to the
physical port.
Indicates the
threshold for
triggering the UL
high load. If the
ratio of the UL
transport load to the
UL transport
bandwidth of the
BS keeps above
this threshold for a
period of
LOFD-001032 /
hysteresis, the UL NO NO No
TDLOFD-001032
transport load of the
BS enters the high-
load state. In UL
high-load state, the
BS sends a UL S1
TNL Load Indicator,
which is set to
HighLoad, to each
neighboring BS
through the X2
interface.
Indicates the
threshold for
triggering the DL
high load. If the
ratio of the DL
DL transport
bandwidth of the
BS keeps above
period of
LOFD-001032 /
hysteresis, the DL NO NO No
TDLOFD-001032
transport load of the
BS enters the high-
load state. In DL
high-load state, the
BS sends a DL S1
TNL Load Indicator,
which is set to
HighLoad, to each
neighboring BS
through the X2
interface.
Indicates the
threshold for
clearing the UL high
load. If the ratio of
the UL transport
load to the UL
transport bandwidth
of the BS keeps
below this threshold
for a period of
hysteresis, the UL LOFD-001032 /
NO NO No
transport load of the TDLOFD-001032
BS enters the
medium-load state.
In UL medium load
state, the BS sends
a UL S1 TNL Load
Indicator, which is
set to MediumLoad,
to each neighboring
BS through the X2
interface.
Indicates the
threshold for
clearing the DL high
load. If the ratio of
the transport load to
the transmission
bandwidth in DL of
the BS keeps below
period of time, the
LOFD-001032 /
DL transport load of NO NO No
TDLOFD-001032
the BS enters the
medium-load state.
In DL medium-load
state, the BS sends
a DL S1 TNL Load
Indicator, which is
set to MediumLoad,
to each neighboring
BS through the X2
interface.
Indicates the
threshold for
triggering the UL
medium load. If the
ratio of the UL
UL transport
bandwidth of the
BS is above this
threshold, the UL
LOFD-001032 /
transport load of the NO NO No
TDLOFD-001032
BS enters the
medium-load state.
In UL medium-load
state, the BS sends
a UL S1 TNL Load
Indicator, which is
set to MediumLoad,
to each neighboring
BS through the X2
interface.
Indicates the
threshold for
triggering the DL
medium load. If the
ratio of the DL
DL transport
bandwidth of the
BS is above this
threshold, the DL
LOFD-001032 /
TDLOFD-001032
BS enters the
medium-load state.
In DL medium-load
state, the BS sends
a DL S1 TNL Load
Indicator, which is
set to MediumLoad,
to each neighboring
BS through the X2
interface.
Indicates the
threshold for
clearing the UL
medium load. If the
ratio of the UL
UL transport
bandwidth of the
BS is below this
threshold, the UL
LOFD-001032 /
TDLOFD-001032
BS enters the low-
load state. In UL
low-load state, the
BS sends a UL S1
TNL Load Indicator,
which is set to
LowLoad, to each
neighboring BS
through the X2
interface.
Indicates the
threshold for
clearing the DL
medium load. If the
ratio of the DL
DL transport
bandwidth of the
BS is below this
threshold, the DL
LOFD-001032 /
TDLOFD-001032
BS enters the low-
load state. In DL
low-load state, the
BS sends a DL S1
TNL Load Indicator,
which is set to
LowLoad, to each
neighboring BS
through the X2
interface.
to enable the
function of clearing
faults on a
transmission link. If
this parameter is
set to ENABLE, a
BS attempts to
clear a fault by
means of automatic
reset when the BS
cannot be
maintained (OMCH
of the BS is
disconnected) and
service interruption
duration reaches 45
minutes. If the fault
fails to be cleared,
the BS attempts to NO NO No None
clear the fault again
in the same way
when the service
interruption duration
reaches 480
minutes. If the fault
fails to be cleared
after the two resets,
the BS stops
performing
automatic reset.
The service
interruption duration
at which the BS
automatically resets
has fixed values (45
minutes and 480
minutes) and is not
Indicates the UL
Over Load Control
(OLC) algorithm
switch. In the case
of enabled switch,
the bandwidth of
the services with
low priority would
LOFD-00301103 /
be released to NO NO No
TDLOFD-00301103
guarantee the QoS
of the services of
high priority when
the TX bandwidth
changes or during
the overload
caused by real-time
services.

for the DL OLC
algorithm. If this
parameter is set to
ON, bandwidth of
the services of a
low priority is
released to
LOFD-00301103 /
guarantee the QoS NO NO No
TDLOFD-00301103
of the services of a
high priority when
transport bandwidth
changes or
overload occurs
due to increased
load of non-flow
control services.
Indicates the
threshold for
triggering the UL
OLC. When the UL
bandwidth
occupancy reaches LOFD-00301103 /
NO NO No
the threshold, low- TDLOFD-00301103
priority services are
removed to
guarantee the
quality of high-
priority services.
Indicates the
threshold for
clearing the UL
OLC. When the UL
LOFD-00301103 /
bandwidth NO NO No
TDLOFD-00301103
occupancy is below
this threshold, user
services are no
longer removed.
Indicates the
number of released LOFD-00301103 /
NO NO No
services during an TDLOFD-00301103
OLC action period.
Indicates the
threshold for
triggering the DL
OLC. When the DL
bandwidth
occupancy reaches LOFD-00301103 /
NO NO No
the threshold, low- TDLOFD-00301103
priority services are
removed to
guarantee the
quality of high-
priority services.
Indicates the
threshold for
clearing the DL
OLC. When the DL
LOFD-00301103 /
bandwidth NO NO No
TDLOFD-00301103
occupancy is below
this threshold, user
services are no
longer removed.
Indicates the mode

of the ping filtering.
When the whitelist
is used, only the
network segments
or hosts specified NO NO No None
by the ping filter
can ping the NE.
When the blacklist
is used, the network
segments or hosts.
Indicates the
number of packets
discarded due to
NO NO Yes None
fragmentation
failures on the
transmitter.
Indicates the
number of received
NO NO Yes None
packets that have
been encrypted.
Indicates the
number of packets
that have been
NO NO Yes None
successfully
decrypted at the
receiver.
Indicates the
number of received
packets that fail the NO NO Yes None
ESP-based
decryption.
Indicates the
number of received
packets that fail the NO NO Yes None
AH-based
authentication.
Indicates the
number of received
packets that should NO NO Yes None
not have been
encrypted.
Indicates the total

number of packets
received by the
NO NO Yes None
decryption module
of the receiver at
the IP layer.
Indicates the total
number of packets
that fail decryption NO NO Yes None
at the IP layer of
the receiver.
Indicates the
number of received NO NO Yes None
IKE packets.
Indicates the
number of
encrypted packets
received by the IP NO NO Yes None
layer of the receiver
from invalid IP
addresses.
Indicates the total
number of packets
discarded at the IP
NO NO Yes None
due to replay
attacks.
Indicates the total

number of packets
discarded at the IP
NO NO Yes None
due to a lack of
inbound SA.
Indicates the total

number of packets
discarded because
the IP layer of the NO NO Yes None
receiver does not
support the AH
algorithm.
Indicates the total

number of packets
discarded because
the IP layer of the NO NO Yes None
receiver does not
support the ESP
algorithm.
Indicates the total

number of plain
packets received at NO NO Yes None
the IP layer of the
receiver.
Indicates the
number of packets
received at the IP
layer that comply NO NO Yes None
with ACL rules and
should have been
encrypted.
Indicates the
number of
transmitted packets
NO NO Yes None
that are
successfully
encrypted.
Indicates the
number of packets
that fail to be NO NO Yes None
encrypted at the
transmitter.
Indicates the total

number of received NO NO Yes None
packets.
Indicates the
number of packets
that need to be NO NO Yes None
encrypted at the
transmitter.
Indicates the
number of packets
discarded at the
NO NO Yes None
transmitter because
the outbound SAs
do not exist.
Indicates the
number of packets
discarded because
NO NO Yes None
the transmitter does
not support the AH
algorithm.
Indicates the
number of packets
discarded because
NO NO Yes None
the transmitter does
not support the
ESP algorithm.
Indicates the
number of packets
that fail the AH-
NO NO Yes None
based
authentication at
the transmitter.
Indicates the
number of
transmitted packets NO NO Yes None
that fail ESP
encryption.
Indicates the
number of packets
discarded due to
NO NO Yes None
transmitting
sequence number
overflow.
Indicates the
number of packets
that do not need to NO NO Yes None
be encrypted at the
transmitter.
Indicates the
number of
NO NO Yes None
transmitted IKE
packets.
Indicates the
number of the MRFD-231501
source cabinet YES NO No LOFD-003002 /
where the tunnel is TDLOFD-003002
configured.
Indicates the
source subrack YES NO No LOFD-003002 /
configured.
Indicates the
source slot where YES YES No LOFD-003002 /
the tunnel is TDLOFD-003002
configured.
MRFD-231501
Indicates the index
of the tunnel.
TDLOFD-003002
Indicates the
destination cabinet NO YES No LOFD-003002 /
located.
Indicates the
destination subrack NO YES No LOFD-003002 /
located.
Indicates the
destination slot NO YES No LOFD-003002 /
located.
Indicates the
MRFD-231501
number of bytes
NO NO Yes LOFD-003002 /
received through
TDLOFD-003002
the tunnel.

MRFD-231501
number of packets
received through a
TDLOFD-003002
tunnel.
MRFD-231501
number of bytes
sent through the
TDLOFD-003002
tunnel.

MRFD-231501
number of packets
sent through the
TDLOFD-003002
tunnel.
Indicates the VLAN

group that the
added VLAN
mapping belongs
to. Multiple VLAN
groups are used in LBFD-003003 /
YES YES No
the scenario in TDLBFD-003003
which telecom
operators share
transport resources
and use different
VLAN policies.

type. Traffic of
different types is
transmitted through
different VLANs.
High-priority OM
data includes the
data of NTP/SNTP,
remote
maintenance
channel switchover,
and TCP (excluding
LBFD-003003 /
that related to FTP). YES YES No
TDLBFD-003003
Low-priority OM
data includes the
data of the File
Transfer Protocol
(FTP) service.
Other data refers to
the data except the
user data,
signaling, high-
priority OM data,
and low-priority OM
data.
Indicates the DSCP LBFD-003003 /

YES NO No
priority of user data. TDLBFD-003003
Indicates the VLAN
LBFD-003003 /
ID that the service NO YES No
TDLBFD-003003
data belongs to.
Indicates the VLAN

priority. A greater
LBFD-003003 /
parameter value NO NO No
TDLBFD-003003
denotes a higher
priority.
Indicates the next

hop IP address LBFD-003003 /
YES YES No
used for mapping TDLBFD-003003
the VLAN.
Indicates the
subnet mask of the
LBFD-003003 /
next hop IP address YES NO No
TDLBFD-003003
used for mapping
the VLAN.
Indicates the VLAN
mode. When this
parameter is set to
SINGLEVLAN, the
configured VLAN ID
and VLAN priority
can be directly used
to label the VLAN
tag.
set to
VLANGROUP, the
next hop IP
addresses are
mapped to the
VLAN groups, and LBFD-003003 /
NO YES No
then mapped to the TDLBFD-003003
VLAN tags in the
VLAN groups
according to the
DSCPs of the IP
packets. In VLAN
group mode,
ensure that the
VLAN groups have
been configured by
running the ADD
VLANCLASS
command.
Otherwise, the
configuration does
not take effect.

NO YES No
ID in the VLAN tag. TDLBFD-003003

NO NO No
priority. TDLBFD-003003
NO YES No
group number. TDLBFD-003003
recommended that
the parameter be
set to DISABLE. In
this case, the
default VLAN
mapping is used.
The following
describes the
default mapping
between DSCPs
and priorities:
If the DSCP is
within the range
from 0 to 7, the
default priority is 0;
If the DSCP is
within the range
from 8 to 15, the
LBFD-003003 /
default priority is 1; NO NO No
TDLBFD-003003
If the DSCP is
within the range
from 16 to 23, the
If the DSCP is
within the range
from 24 to 31, the
If the DSCP is
within the range
from 32 to 39, the
If the DSCP is
within the range
from 40 to 47, the
If the DSCP is
within the range
Indicates the
maximum wait time
for an echo
response. If no
echo response is NO NO No None
received during the
period specified by
this parameter, the
timer has expired.
Indicates the
maximum number
of timeouts of the
echo response
waiting timer. If no
echo response is NO NO No None
received after the
number specified
by this parameter is
reached, the GTP-
U path in use fails.
Indicates the
Differentiated
Services Code
NO NO No None
Point (DSCP) of a
GTP-U control
packet.
Indicates whether
to enable static
detection in
compliance with
GPRS Tunneling
Protocol for User
Plane (GTP-U). If
this parameter is
set to ENABLE, the
GTP-U static check
NO NO No None
is enabled. In this
case, the ALM-
25886 IP Path Fault
alarm is reported if
a link bearing an IP
path is faulty. If this
parameter is set to
DISABLE, the GTP-
U static check is
disabled.
Enumeration
Feature Name Value Type GUI Value Range Unit
Number/Bit
Remote Electrical
Interval Type 0~35 N/A None
Tilt Control
Remote Electrical
Interval Type 0 N/A None
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical Character String

0~128 characters N/A None
Tilt Control Type
Remote Electrical
Interval Type 0~15 N/A degree
Tilt Control
Remote Electrical
Interval Type 30,65,90,360 N/A degree
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical INTELLIGENT, INTELLIGENT~1,

Enumeration Type None
Tilt Control DISTRIBUTED DISTRIBUTED~2
Remote Electrical SINGLE~1,

Enumeration Type SINGLE, DUAL None
Tilt Control DUAL~2
Remote Electrical
Tilt Control
FOURPORTS(Four
Remote Electrical Ports), FOURPORTS~0,
Tilt Control EIGHTPORTS(Eigh EIGHTPORTS~1
t Ports)
Remote Electrical
Interval Type 0~100 N/A 0.01
Tilt Control
Remote Electrical
Interval Type -180~180 N/A degree
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
None Interval Type 0~1048575 N/A None
Character String
None 1~64 characters N/A None
Type
DBS3900_LTE(DB
S3900 LTE),
BTS3900_LTE(BTS
DBS3900_LTE~1,
3900 LTE),
BTS3900_LTE~2,
BTS3900A_LTE(BT
None Enumeration Type BTS3900A_LTE~3, None
S3900A LTE),
BTS3900L_LTE~4,
BTS3900L_LTE(BT
BTS3900AL_LTE~5
S3900L LTE),
BTS3900AL_LTE(B
TS3900AL LTE)
Adaptive Power
Enumeration Type ON(ON), OFF(OFF) ON~0, OFF~1 None
Consumption
Adaptive Power
Compound Type 22:00:00~5:00:00 N/A None
Consumption
Adaptive Power
Consumption
-
None Interval Type 180000000~18000 N/A 1e-6 degree
0000
-
00
Character String
Type
Default~0,
Default, Normal, Normal~1,
None Enumeration Type Demo, Protected, Demo~2, None
Emergency Protected~3,
Emergency~4
Poweroff(Power Poweroff~0,
None Enumeration Type None
off), Normal Normal~1
Character String
Type
None Enumeration Type DEG, SEC DEG~0, SEC~1 None
Character String
None 0~16 characters N/A s
Type
Character String
Type
None Enumeration Type CPRI, TDL_IR CPRI~0, TDL_IR~1 None

smission Packet
Loss Rate),
Transmission_Dela
y(Transmission
Delay),
Transmission_Jitter(
Transmission Jitter),
Transmission_Pack
Packet_Loss_Rate(
et_Loss_Rate~0,
Packet Loss Rate),
Transmission_Dela
Cell_RRC_Connect
y~1,
_Succ_Rate(Cell
Transmission_Jitter
RRC Connect Succ
~2,
Rate),
Packet_Loss_Rate
Cell_ERAB_Setup_
~3,
Succ_Rate(Cell
Cell_RRC_Connect
ERAB Setup Succ
_Succ_Rate~4,
Rate),
Cell_ERAB_Setup_
Cell_Call_Drop_Rat
Succ_Rate~5,
e(Cell Call Drop
None Enumeration Type Cell_Call_Drop_Rat None
Rate), Intra-
e~6, Intra-
Frequency_HO_Su
Frequency_HO_Su
cc_Rate(Intra-
cc_Rate~7, Inter-
Frequency HO
Frequency_HO_Su
Succ Rate), Inter-
cc_Rate~8, LTE-
Frequency_HO_Su
CDMA_Handover_
cc_Rate(Inter
Succ_Rate~9, LTE-
Frequency HO
WCDMA_Handover
Succ Rate), LTE-
_Succ_Rate~10,
CDMA_Handover_
LTE-
Succ_Rate(LTE-
GERAN_Handover
CDMA Handover
_Succ_Rate~11
Succ Rate), LTE-
WCDMA_Handover
_Succ_Rate(LTE-
WCDMA Handover
Succ Rate), LTE-
GERAN_Handover
_Succ_Rate(LTE-
None Enumeration Type ON(ON), OFF(OFF) ON~0, OFF~1 None

15minutes(15minut
es),
15minutes~15,
30minutes(30minut
30minutes~30,
None Enumeration Type es), min
60minutes~60,
60minutes(60minut
1day~1440
es), 1day(1day
1440minutes)
None Interval Type 0~23 N/A h

-
0000
-
00
1T1R~0, 1T2R~1,
1T1R, 1T2R, 2T2R,
None Enumeration Type 2T2R~3, 2T4R~4, None
2T4R, 4T4R, 8T8R
4T4R~5, 8T8R~6
NormalMIMO(Norm
RRU Channel
al MIMO), NormalMIMO~0,
Cross Connection Enumeration Type None
AIDMIMO(mutual- AIDMIMO~1
Under MIMO
aid MIMO)
COMBTYPE_SING COMBTYPE_SING
LE_RRU, LE_RRU~0,
COMBTYPE_TWO COMBTYPE_TWO
_RRU, _RRU~1,
COMBTYPE_THRE COMBTYPE_THRE
E_RRU, E_RRU~2,
COMBTYPE_FOU COMBTYPE_FOU
R_RRU, R_RRU~3,
COMBTYPE_FIVE_ COMBTYPE_FIVE_
RRU, RRU~4,
COMBTYPE_SIX_ COMBTYPE_SIX_
RRU, RRU~5,
COMBTYPE_SEVE COMBTYPE_SEVE
N_RRU, N_RRU~6,
COMBTYPE_EIGH COMBTYPE_EIGH
T_RRU T_RRU~7
None Interval Type 4~5,60~254 N/A None

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
None Enumeration Type R2A~32, R2B~33, None
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
Character String
Type
None Interval Type -32767~32767 N/A m
None Interval Type 0~1800000 N/A m

None Interval Type 0~179 N/A degree

None Interval Type 0~100 N/A %
None Enumeration Type DEG, SEC DEG~0, SEC~1 None
Character String
Type
Character String
Type
None Enumeration Type FALSE, TRUE FALSE~0, TRUE~1 None

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113

R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
R0A~0, R0B~1,
R0C~2, R0D~3,
R0A, R0B, R0C,
R0E~4, R0F~5,
R0D, R0E, R0F,
R0G~6, R0H~7,
R0G, R0H, R1A,
R1A~16, R1B~17,
R1B, R2A, R2B,
R3A, R3B, R4A,
R3A~48, R3B~49,
R4B, R5A, R5B,
R4A~64, R4B~65,
R6A, R6B, R7A,
R5A~80, R5B~81,
R7B
R6A~96, R6B~97,
R7A~112, R7B~113
None Interval Type 0~500 N/A 0.1dBm

Normal~0,
None Enumeration Type Normal, NoLicense None
NoLicense~1
Character String
None 0~40 characters N/A 0.1MHz
Type
Character String
None 0~40 characters N/A 0.1MHz
Type
COMPATIBLE, COMPATIBLE~0,
HTTPS_ONLY, HTTPS_ONLY~1,
LOGIN_HTTPS_O LOGIN_HTTPS_O
NLY NLY~2
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type
Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Interval Type 4~5,60~254 N/A None
Tilt Control
Remote Electrical
Tilt Control
AISG1.1(AISG1.1), AISG1.1~1,
Remote Electrical AISG2.0(AISG2.0), AISG2.0~2,
Tilt Control 3GPP(3GPP), 3GPP~3,
UNKNOWN(NULL) UNKNOWN~255
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type

Tilt Control Type

Tilt Control Type

Tilt Control Type
SINGLE_RET(SIN
GLE_RET), SINGLE_RET~1,
Remote Electrical
Enumeration Type STMA(STMA), STMA~2, None
Tilt Control
MULTI_RET(MULTI MULTI_RET~17
_RET)
R0A(R0A),
R0B(R0B),
RET_PORT(RET_P R0A~0, R0B~1,
ORT), R0C(R0C), RET_PORT~2,
R0D(R0D), R0C~3, R0D~4,
R0E(R0E), R0E~5, R0F~6,
R0F(R0F), R0G~7, R0H~8,
R0G(R0G), NULL~65535
R0H(R0H),
NULL(NULL)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
R0A(R0A),
R0B(R0B),
R0C(R0C), R0A~0, R0B~1,
Remote Electrical R0D(R0D), R0C~2, R0D~3,
Tilt Control R0E(R0E), R0E~4, R0F~5,
R0F(R0F), R0G~6, R0H~7
R0G(R0G),
R0H(R0H)
Remote Electrical
Interval Type 0~50 N/A ns
Tilt Control
Remote Electrical
Interval Type 0~50 N/A ns
Tilt Control
Remote Electrical
Tilt Control
UER_SELF_DEFIN
E(UER_SELF_DEF
INE),
TMA12DB_ONLY_
UER_SELF_DEFIN
NON_AISG(TMA12
E~0,
DB_ONLY_NON_AI
TMA12DB_ONLY_
SG),
NON_AISG~1,
TMA24DB_ONLY_
TMA24DB_ONLY_
Remote Electrical NON_AISG(TMA24
Enumeration Type NON_AISG~2, None
Tilt Control DB_ONLY_NON_AI
RET_ONLY_COAXI
SG),
AL~3,
RET_ONLY_COAXI
TMA12DB_AISG~5
AL(RET_ONLY_CO
,
AXIAL),
TMA24DB_AISG~6
TMA12DB_AISG(T
MA12DB_AISG),
TMA24DB_AISG(T
MA24DB_AISG)
Remote Electrical
Interval Type 0~3500 N/A mA
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
ON(ON),
Remote Electrical ON~0, OFF~1,
Enumeration Type OFF(OFF), None
Tilt Control NULL~4294967295
NULL(NULL)
SINGLE_RET(SIN
Remote Electrical GLE_RET), SINGLE_RET~1,
Tilt Control MULTI_RET(MULTI MULTI_RET~17
_RET)
Remote Electrical SINGLE(SINGLE), SINGLE~1,
Tilt Control DUAL(DUAL) DUAL~2
REGULAR(REGUL
Remote Electrical AR), REGULAR~1,
Tilt Control DAISY_CHAIN(DAI DAISY_CHAIN~2
SY_CHAIN)
Remote Electrical
Tilt Control
RET(RET),
None Enumeration Type RET~0, VRET~1 None
VRET(Virtual RET)
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type
Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type

Tilt Control Type

Tilt Control Type

Tilt Control Type
SINGLE_RET(SIN
Remote Electrical
Tilt Control
_RET)
R0A(R0A),
R0B(R0B),
R0D(R0D), R0C~3, R0D~4,
R0E(R0E), R0E~5, R0F~6,
R0F(R0F), R0G~7, R0H~8,
R0H(R0H),
NULL(NULL)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Interval Type 0~255 N/A 0.1dBi
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Tilt Control Type
Remote Electrical
Interval Type -100~300 N/A 0.1degree
Tilt Control

Tilt Control Type
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
Remote Electrical BandV~5,
Enumeration Type BandV(BandV), None
Tilt Control BandVI~6,
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)

Tilt Control Type

Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
None Enumeration Type BandVI~6, None
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
None Interval Type 0~255 N/A 0.1dBi
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical RET_PORT(RET_P

Enumeration Type RET_PORT~2 None
Tilt Control ORT)
Remote Electrical
Tilt Control
UER_SELF_DEFIN
E(UER_SELF_DEF UER_SELF_DEFIN
Remote Electrical INE), E~0,
Tilt Control RET_ONLY_MULTI RET_ONLY_MULTI
CORE(RET_ONLY CORE~4
_MULTICORE)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
ON(ON),
Remote Electrical ON~0, OFF~1,
Enumeration Type OFF(OFF), None
Tilt Control NULL~4294967295
NULL(NULL)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
AVAILABLE(AVAILA
BLE),
UNAVAILABLE(UN AVAILABLE~0,
Remote Electrical AVAILABLE), UNAVAILABLE~1,
Tilt Control BREAKLINK(BREA BREAKLINK~2,
KLINK), RESERVED~3
RESERVED(RESE
RVED)
Remote Electrical
Tilt Control
Remote Electrical
Interval Type 0~62,255 N/A None
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
R0A(R0A),
R0B(R0B),
R0C(R0C), R0A~0, R0B~1,
R0F(R0F), R0G~6, R0H~7
R0G(R0G),
R0H(R0H)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
R0A(R0A),
R0B(R0B),
R0C(R0C), R0A~0, R0B~1,
R0F(R0F), R0G~6, R0H~7
R0G(R0G),
R0H(R0H)
Remote Electrical
Tilt Control
Remote Electrical
Interval Type 0~10 N/A 0.1degree
Tilt Control

Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type
Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control

Tilt Control Type

Tilt Control Type

Tilt Control Type

Tilt Control Type

Tilt Control Type
SINGLE_RET(SIN
Remote Electrical
Tilt Control
_RET)
R0A(R0A),
R0B(R0B),
R0D(R0D), R0C~3, R0D~4,
R0E(R0E), R0E~5, R0F~6,
R0F(R0F), R0G~7, R0H~8,
R0H(R0H),
NULL(NULL)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control

Tilt Control Type
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control

Tilt Control Type
Remote Electrical
Tilt Control

Tilt Control Type
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10
BandX(BandX)

Tilt Control Type

Tilt Control Type

Tilt Control Type
Remote Electrical
Interval Type 0~4294967295 N/A 0.25dB
Tilt Control
Remote Electrical
Tilt Control
UNSUPPORT(UNS
UPPORT),
SUPPORT_BYPAS UNSUPPORT~0,
S(SUPPORT_BYP SUPPORT_BYPAS
ASS), S~1,
None Enumeration Type SUPPORT_VSWR( SUPPORT_VSWR~ None
SUPPORT_VSWR) 2,
, VSWR/BYPASS~3,
VSWR/BYPASS(VS NULL~4294967295
WR/BYPASS),
NULL(NULL)
None Interval Type 0~255 N/A 0.25dB
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)
UNUSED(UNUSED
UNUSED~0,
), BandI(BandI),
BandI~1, BandII~2,
BandII(BandII),
BandIII~3,
BandIII(BandIII),
BandIV~4,
BandIV(BandIV),
BandV~5,
BandV(BandV),
BandVI(BandVI),
BandVII~7,
BandVII(BandVII),
BandVIII~8,
BandVIII(BandVIII),
BandIX~9,
BandIX(BandIX),
BandX~10,
BandX(BandX),
NULL~4294967295
NULL(NULL)

Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
NORMAL(NORMAL
NORMAL~0,
Remote Electrical ),
Enumeration Type BYPASS~1, None
Tilt Control BYPASS(BYPASS),
NULL~4294967295
NULL(NULL)
AVAILABLE(AVAILA
BLE),
UNAVAILABLE(UN AVAILABLE~0,
Remote Electrical AVAILABLE), UNAVAILABLE~1,
Tilt Control BREAKLINK(BREA BREAKLINK~2,
KLINK), RESERVED~3
RESERVED(RESE
RVED)
R0A(R0A),
R0B(R0B),
R0C(R0C), R0A~0, R0B~1,
R0F(R0F), R0G~6, R0H~7
R0G(R0G),
R0H(R0H)
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
Remote Electrical
Tilt Control
NORMAL(NORMAL
Remote Electrical NORMAL~0,
Enumeration Type ), None
Tilt Control BYPASS~1
BYPASS(BYPASS)
None Interval Type 0 N/A None
R0A(R0A),
R0B(R0B),
R1A(R1A),
R1B(R1B),
R0A~0, R0B~1,
R2A(R2A),
R1A~16, R1B~17,
R2B(R2B),
R2A~32, R2B~33,
R3A(R3A),
R3A~48, R3B~49,
R3B(R3B),
R4A~64, R4B~65,
None Enumeration Type R4A(R4A), None
R5A~80, R5B~81,
R4B(R4B),
R6A~96, R6B~97,
R5A(R5A),
R7A~112,
R5B(R5B),
R7B~113,
R6A(R6A),
NULL~255
R6B(R6B),
R7A(R7A),
R7B(R7B),
NULL(NULL)

Character String
Type
R0A(R0A),
R0B(R0B),
R1A(R1A),
R1B(R1B),
R0A~0, R0B~1,
R2A(R2A),
R1A~16, R1B~17,
R2B(R2B),
R2A~32, R2B~33,
R3A(R3A),
R3A~48, R3B~49,
R3B(R3B),
R4A~64, R4B~65,
R5A~80, R5B~81,
R4B(R4B),
R6A~96, R6B~97,
R5A(R5A),
R7A~112,
R5B(R5B),
R7B~113,
R6A(R6A),
NULL~255
R6B(R6B),
R7A(R7A),
R7B(R7B),
NULL(NULL)
R0A(R0A),
R0B(R0B),
R1A(R1A),
R1B(R1B),
R0A~0, R0B~1,
R2A(R2A),
R1A~16, R1B~17,
R2B(R2B),
R2A~32, R2B~33,
R3A(R3A),
R3A~48, R3B~49,
R3B(R3B),
R4A~64, R4B~65,
R5A~80, R5B~81,
R4B(R4B),
R6A~96, R6B~97,
R5A(R5A),
R7A~112,
R5B(R5B),
R7B~113,
R6A(R6A),
NULL~255
R6B(R6B),
R7A(R7A),
R7B(R7B),
NULL(NULL)
Character String
Type
NEGATIVE_45, NEGATIVE_45~0,
POSITIVE_45, POSITIVE_45~1,
HORIZONTAL, HORIZONTAL~2,
None Enumeration Type VERTICAL, LEFT, VERTICAL~3, None
RIGHT, LEFT~4, RIGHT~5,
POSITIVE_NEGATI POSITIVE_NEGATI
VE_45 VE_45~6

R0A(R0A),
R0B(R0B),
R1A(R1A),
R1B(R1B),
R0A~0, R0B~1,
R2A(R2A),
R1A~16, R1B~17,
R2B(R2B),
R2A~32, R2B~33,
R3A(R3A),
R3A~48, R3B~49,
R3B(R3B),
R4A~64, R4B~65,
R5A~80, R5B~81,
R4B(R4B),
R6A~96, R6B~97,
R5A(R5A),
R7A~112,
R5B(R5B),
R7B~113,
R6A(R6A),
NULL~255
R6B(R6B),
R7A(R7A),
R7B(R7B),
NULL(NULL)
VE_45 VE_45~6
None Interval Type -150~150,32767 N/A 0.1degree
None Interval Type -150~150,32767 N/A 0.1degree

R0A(R0A),
R0B(R0B),
R1A(R1A),
R1B(R1B),
R0A~0, R0B~1,
R2A(R2A),
R1A~16, R1B~17,
R2B(R2B),
R2A~32, R2B~33,
R3A(R3A),
R3A~48, R3B~49,
R3B(R3B),
R4A~64, R4B~65,
R5A~80, R5B~81,
R4B(R4B),
R6A~96, R6B~97,
R5A(R5A),
R7A~112,
R5B(R5B),
R7B~113,
R6A(R6A),
NULL~255
R6B(R6B),
R7A(R7A),
R7B(R7B),
NULL(NULL)
VE_45 VE_45~6
VE_45 VE_45~6
None Interval Type 0,1,2,4 N/A None

None Interval Type 0~4,8 N/A None
2000-01-01
None Compound Type 00:00:00~2038-12- N/A None
31 23:59:59
None Interval Type 0~4294967295 N/A packet

None Interval Type 0~65535 N/A per mill
None Interval Type 0~4294967295 N/A s

Character String
None 0~31 characters N/A packet
Type
DEACTIVATED(De
activated), DEACTIVATED~0,
ACTIVATED(Activat ACTIVATED~1
ed)
UNAVAILABLE(Una
vailable), UNAVAILABLE~0,
AVAILABLE(Availab AVAILABLE~1
le)

DEACTIVATED(De
ed)
UNAVAILABLE(Una
le)

UMTS(UMTS),
GSM(GSM), UMTS~0, GSM~1,
DEFAULT(DEFAUL DEFAULT~255
T)
DEACTIVATED(De
ed)
UNAVAILABLE(Una
le)

IN(Input),
None Enumeration Type IN~0, OUT~1 None
OUT(Output)

TWISTED-
TWISTED-PAIR~0,
None Enumeration Type PAIR(Twisted-Pair), None
COAXIAL~1
COAXIAL(Coaxial)
DEACTIVATED(De
ed)
UNAVAILABLE(Una
le)
None Interval Type 0~100000 N/A ns

RGPS CLOCK
TRANSMIT FROM
RRU TO BBU
THROUGH CPRI
USER_CONFIG(Us
er Config),
SEARCH_WITH_D USER_CONFIG~0,
URATION(Search SEARCH_WITH_D
with duration), URATION~1,
SEARCH_WITH_P SEARCH_WITH_P
RECISION(Search RECISION~2,
with precision), AUTO_SEARCH~3
AUTO_SEARCH(A
uto Search)
-
0000
-
00
None Interval Type -1000~10000 N/A m
None Interval Type 0~100000 N/A ns
None Interval Type 1~2880 N/A min

TWISTED-
TWISTED-PAIR~0,
None Enumeration Type PAIR(Twisted-Pair), None
COAXIAL~1
COAXIAL(Coaxial)
Character String
Type
Lock(Yes),
None Enumeration Type Lock~0, Unlock~1 None
Unlock(No)
Valid(Valid),
None Enumeration Type Valid~0, Invalid~1 None
Invalid(Invalid)
Valid(Valid),
Invalid(Invalid)
NotFixed(Not NotFixed~0,
Fixed), Fixed(Fixed) Fixed~1
Enabled(Enabled), Enabled~0,
Disabled(Disabled) Disabled~1
Valid(Valid),
Invalid(Invalid)
NOTEXIST(Inexiste
nt),
ANTENNASHORTE
D(Antenna
Shorted),
ANTENNAOPENE NOTEXIST~0,
D(Antenna ANTENNASHORTE
Opened), D~1,
SELF_CHECK_FAI ANTENNAOPENE
LURE(Self-check D~2,
Failure), SELF_CHECK_FAI
None Enumeration Type COMEXCEPTION( LURE~3, None
COM Port COMEXCEPTION~
Communication 4, NORMAL~5,
Fault), UNKNOWN~6,
NORMAL(Normal), USCUINVALID~7,
UNKNOWN(Unkno UNKNOWN_STAR
wn Exception), _CARD~8
USCUINVALID(US
CU Invalid),
UNKNOWN_STAR
_CARD(Unknown
Star Card)
M12M(M12M),
UT(UT), RT(RT),
JPS15L(JPS15L), M12M~0, UT~1,
K161(K161), RT~2, JPS15L~3,
GG16(GG16), K161~4, GG16~5,
JNS100(JNS100), JNS100~6,
RGPS(RGPS), RGPS~7,
CWAIN(CWAIN), CWAIN~8,
RTSMT(RTSMT), RTSMT~9,
UBLOX5(UBLOX5), UBLOX5~10,
BD7702(BD7702), BD7702~11,
NAVIOR(NAVIOR), NAVIOR~12,
PPSTOD(PPSTOD) PPSTOD~13,
, M1000(M1000), M1000~14,
TRGPS(TRGPS), TRGPS~15,
BD7702CMS(BD77 BD7702CMS~16,
02CMS), OEM4~17,
OEM4(OEM4), UNKNOWN~65535
UNKNOWN(Unkno
wn)

GPS(GPS),
GLONASS(GLONA
SS),
GPS/GLONASS(G
PS/GLONASS with
GPS~0,
GPS Prioritized),
GLONASS~1,
COMPASS(COMPA
GPS/GLONASS~2,
None Enumeration Type SS), None
COMPASS~3,
COMPASS/GPS(C
COMPASS/GPS~4,
OMPASS/GPS with
GPS/COMPASS~5
COMPASS
Prioritized),
GPS/COMPASS(G
PS/COMPASS with
GPS Prioritized)
DEACTIVATED(De
ed)

IEEE1588 V2 Clock
HW_DEFINED(Hua
Synchronization
Wei Defined HW_DEFINED~0,
Clock over IP Enumeration Type None
Protocol), PTP(PTP PTP~1
(Huawei
Protocol)
proprietary)

IEEE1588 V2 Clock
Synchronization
Clock over IP IP Address Type Valid IP address N/A None
(Huawei
proprietary)
IEEE1588 V2 Clock
Synchronization
(Huawei
proprietary)
IEEE1588 V2 Clock
Synchronization
E2E(E2E),
None Enumeration Type E2E~0, P2P~1 None
P2P(P2P)
None Enumeration Type OFF(OFF), ON(ON) OFF~0, ON~1 None
None Enumeration Type NO(NO), YES(YES) NO~0, YES~1 None
None Compound Type 14 characters N/A None

DEACTIVATED(De
ed)
UNAVAILABLE(Una
le)
UNICAST(Unicast),
IEEE1588 V2 Clock UNICAST~0,
Enumeration Type L2_MULTICAST(L2 None
Synchronization L2_MULTICAST~2
Multicast)
IEEE1588 V2 Clock
Interval Type -100000~100000 N/A ns
Synchronization
ONE_STEP(One
Step), ONE_STEP~0,
TWO_STEP(Two TWO_STEP~1
Step)
-
483647
1/16(1/16), 1/8(1/8), 1/16~0, 1/8~1,

1/4(1/4), 1/2(1/2), 1/4~2, 1/2~3,
None Enumeration Type Hz
1.0(1.0), 2.0(2.0), 1.0~4, 2.0~5,
4.0(4.0), 8.0(8.0) 4.0~6, 8.0~7
1/2(1/2), 1.0(1.0),
1/2~0, 1.0~1,
2.0(2.0), 4.0(4.0),
2.0~2, 4.0~3,
8.0(8.0), 16.0(16.0),
None Enumeration Type 8.0~4, 16.0~5, Hz
32.0(32.0),
32.0~6, 64.0~7,
64.0(64.0),
128.0~8
128.0(128.0)

1588V2(1588V2), 1588V2~0,
G.8265.1(G.8265.1) G.8265.1~1
IPV4(IPv4),
None Enumeration Type IPV4~0, IPV6~1 None
IPV6(IPv6)
None IP Address Type Valid IP address N/A None
IEEE1588 V2 Clock
Synchronization
(Huawei
proprietary)
DISABLE(DISABLE
DISABLE~0,
None Enumeration Type ), None
ENABLE~1
ENABLE(ENABLE)
DEACTIVATED(De
Synchronization
with Ethernet(ITU-T Enumeration Type None
G.8261)
ed)
UNAVAILABLE(Una
Synchronization
with Ethernet(ITU-T Enumeration Type None
G.8261)
le)
AVAILABLE(Availab
le),
UNAVAILABLE(Una AVAILABLE~0,
UNSUPPORT(Unsu UNSUPPORT~2,
pport), PARTAVAILABLE~3
PARTAVAILABLE(P
artial Available)
FORBID(Forbid),
FORBID~0,
None Enumeration Type ALLOW(Allow), None
ALLOW~1, NA~2
NA(N/A)
0(0), 1(1), 2(2), 0~0, 1~1, 2~2, 3~3,

3(3), 4(4), 5(5), 4~4, 5~5, 6~6, 7~7,
6(6), 7(7), 8(8), 8~8, 9~9, 10~10,
9(9), 10(10), 11(11), 11~11, 12~12,
12(12), 13(13), 13~13, 14~14,
14(14), 15(15), 15~15, 16~16,
16(16), 17(17), 17~17,
AUTO(AUTO) AUTO~65535
GPS(GPS Clock),
BITS(BITS Clock),
IPCLK(IP Clock),
SYNCETH(SyncEth
GPS~0, BITS~1,
Clock),
IPCLK~2,
LINECLK(Line
SYNCETH~3,
Clock), TOD(TOD
LINECLK~4,
Clock),
None Enumeration Type TOD~5, None
PEERCLK(Peer
PEERCLK~6,
Clock),
SYNCETH+IPCLK~
SYNCETH+IPCLK(
7,
SyncEth Clock+IP
GPS+SYNCETH~8
Clock),
GPS+SYNCETH(G
PS Clock+SyncEth
Clock)
Clock Source AUTO(Auto), AUTO~0,

Switching Manually Enumeration Type MANUAL(Manual), MANUAL~1, None
or Automatically FREE(Free) FREE~2
FREQ(FREQ),
None Enumeration Type FREQ~0, TIME~1 None
TIME(TIME)
NORMAL(Normal),
LOST(Lost),
UNAVAILABLE(Una
NORMAL~0,
vailable),
LOST~1,
FREDVAT(Frequen
UNAVAILABLE~2,
cy Deviation),
FREDVAT~3,
JITTER(Jitter),
None Enumeration Type JITTER~4, None
PHASEOUTSCOP
PHASEOUTSCOP
E(Phaseoutscope),
E~5,
UNKNOWN(Unkno
UNKNOWN~6,
wn),
DIFFSRC~7
DIFFSRC(Inconsist
ent Clock
References)
FREERUNNING(Fr
ee running),
FASTTRACKING(F FREERUNNING~0,
ast tracking), FASTTRACKING~1
None Enumeration Type LOCKED(Locked), , LOCKED~2, None
HOLDOVER(Holdo HOLDOVER~3,
ver), UNKNOWN~4
UNKNOWN(Unkno
wn)
GPS(GPS Clock),
BITS(BITS Clock),
IPCLK(IP Clock),
SYNCETH(SyncEth
GPS~0, BITS~1,
Clock),
IPCLK~2,
LINECLK(Line
SYNCETH~3,
Clock), TOD(TOD
LINECLK~4,
Clock),
None Enumeration Type TOD~5, None
PEERCLK(Peer
PEERCLK~6,
Clock),
SYNCETH+IPCLK~
SYNCETH+IPCLK(
7,
SyncEth Clock+IP
GPS+SYNCETH~8
Clock),
GPS+SYNCETH(G
PS Clock+SyncEth
Clock)

QL-PRC(QL-PRC),
QL-SSU-A(QL-
QL-PRC~2, QL-
SSU-A), QL-SSU-
SSU-A~4, QL-SSU-
B(QL-SSU-B), QL-
None Enumeration Type B~8, QL-EEC2~10, None
EEC2(QL-EEC2),
QL-EEC1~11, QL-
QL-EEC1(QL-
DNU~15
EEC1), QL-
DNU(QL-DNU)
None Enumeration Type LBBP(LBBP) LBBP~12290 None

FDD(Frequency
Division Duplex),
TDD(Time Division
FDD~0, TDD~1,
Duplex),
TDD_ENHANCE~3,
None Enumeration Type TDD_ENHANCE(S None
TDD_8T8R~4,
upport TDD BF),
TDD_TL~5
TDD_8T8R(TDD_8
T8R),
TDD_TL(TDD_TL)
BLOCKED(Blocked
), BLOCKED~0,
UNBLOCKED(Unbl UNBLOCKED~1
ocked)

IMMEDIATE(Immed IMMEDIATE~0,
iate), DELAY(Delay) DELAY~2
Alarm_0(Normal), Alarm_0~0,
Alarm_1(Warning), Alarm_1~1,
Alarm_2(Minor), Alarm_2~2,
Alarm_4(Major), Alarm_4~4,
Alarm_8(Critical), Alarm_8~8,
Alarm_15(Critical) Alarm_15~15
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
ication lost, In test),
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
None Enumeration Type Avail_c30(Power None
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
off, Fault, In test),
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
ed, Fault, In test),
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
None Enumeration Type UNKNOWN~254, None
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
SLAVE_CPU(Slave CPU~1, DSP~2,
CPU), SLAVE_CPU~3,
MDU_CPU(MDU_C MDU_CPU~4,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
None Interval Type 2147483648~2147 N/A degree Celsius
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
NCD(NCD), Master~0, NDD~1,
NDC(NDC), NCD~2, NDC~3,
NEC(NEC), NEC~4, EUL~5,
EUL(EUL), EDL~6, Slave~7
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBRACK(SUBRA SUBRACK~1,
None Enumeration Type CK), BOARD~2, None
BOARD(BOARD), SUBBOARD~3,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
None Enumeration Type Timeout~2, None
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
-
483647
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

None Enumeration Type NO(NO), YES(YES) NO~0, YES~1 None
GSM(GSM),
GSM~0, UMTS~1,
None Bit Field Type UMTS(UMTS), None
LTE~2
LTE(LTE)
WS_DISABLE(Wat
er-Immersed
WS_DISABLE~0,
None Bit Field Type Sensor Disabled), None
SS_DISABLE~1
SS_DISABLE(Smo
g Sensor Disabled)
CONNECTED(Con
CONNECTED~0,
nected),
None Enumeration Type DISCONNECTED~ None
DISCONNECTED(
1
Disconnected)
CONNECTED(Con
CONNECTED~0,
nected),
None Enumeration Type DISCONNECTED~ None
DISCONNECTED(
1
Disconnected)

LBR0(NULL),
LBR1(1.25),
LBR0~0, LBR1~1,
LBR2(2.5),
LBR2~2, LBR3~4,
None Enumeration Type LBR3(3.0), Gbit/s
LBR4~8, LBR5~16,
LBR4(4.9),
LBR6~32
LBR5(6.1),
LBR6(9.8)
NEGOTIATED(Neg
otiated),
NEGOTIATING(Ne
NEGOTIATED~0,
gotiating),
NEGOTIATING~1,
NOTREADY(Not
None Enumeration Type NOTREADY~2, None
ready),
TIMEOUT~3,
TIMEOUT(Timeout)
USERCONFIG~5
,
USERCONFIG(US
ERCONFIG)
LBR0(NULL),
LBR1(1.25),
LBR0~0, LBR1~1,
LBR2(2.5),
LBR2~2, LBR3~4,
LBR4~8, LBR5~16,
LBR4(4.9),
LBR6~32
LBR5(6.1),
LBR6(9.8)
NEGOTIATED(Neg
otiated),
NEGOTIATING(Ne
NEGOTIATED~0,
gotiating),
NEGOTIATING~1,
NOTREADY(Not
None Enumeration Type NOTREADY~2, None
ready),
TIMEOUT~3,
TIMEOUT(Timeout)
USERCONFIG~5
,
USERCONFIG(US
ERCONFIG)
HEAD(Head), HEAD~4294967294
TAIL(Tail) , TAIL~4294967295
LBR0(NULL),
LBR1(1.25),
LBR0~0, LBR1~1,
LBR2(2.5),
LBR2~2, LBR3~4,
LBR4~8, LBR5~16,
LBR4(4.9),
LBR6~32
LBR5(6.1),
LBR6(9.8)

None Interval Type 0~1,4~5,60~254 N/A None

614M(614M),
1.25G(1.25G),
2.5G(2.5G), 614M~0, 1.25G~1,
4.9G(4.9G), 2.5G~2, 4.9G~3,
None Enumeration Type 6.1G(6.1G), 6.1G~4, 9.8G~5, bit/s
9.8G(9.8G), UNKNOWN~254,
UNKNOWN(UNKN NULL~255
OWN),
NULL(NULL)
BLOCKED(Blocked
),
BLOCKED~0,
UNBLOCKED(Unbl
UNBLOCKED~1,
None Enumeration Type ocked), None
SHUTINGDOWN~2
SHUTINGDOWN(S
, INVALID~4
hutingdown),
INVALID(NULL)
INPOSITION(In
Position), INPOSITION~0,
None Enumeration Type NOTINPOSITION(N NOTINPOSITION~ None
ot In Position), 1, INVALID~255
INVALID(NULL)
Slave(Slave),
Slave~0, Master~1,
None Enumeration Type Master(Master), None
NULL~255
NULL(NULL)
SFP_OPTICAL(SF
P_OPTICAL),
ESFP_OPTICAL(E
SFP_OPTICAL~0,
SFP_OPTICAL),
ESFP_OPTICAL~1,
SFP_ELECTRIC(S
SFP_ELECTRIC~2,
FP_ELECTRIC),
None Enumeration Type SCSI_ELECTRIC~ None
SCSI_ELECTRIC(S
3, GE~4,
CSI_ELECTRIC),
UNKNOWN~254,
GE(GE),
NULL~255
UNKNOWN(UNKN
OWN),
NULL(NULL)

CPRI_MUX(CPRI
CPRI_MUX~0,
MUX),
NORMAL~253,
None Enumeration Type NORMAL(Normal), None
UNKNOWN~254,
UNKNOWN(Unkno
NULL~255
wn), NULL(NULL)
None Enumeration Type DC(DC), AC(AC) DC~0, AC~1 None
UMPT(UMPT), UMPT~1,
LMPT(LMPT) LMPT~12289
Unknown(Unknown
Unknown~0,
), NULL(NULL),
None Enumeration Type NULL~1, Active~2, None
Active(Active),
Standby~3
Standby(Standby)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
None Enumeration Type NULL(NULL) NULL~4294967295 W
None Enumeration Type NULL(NULL) NULL~4294967295 W

Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
DISABLE(Disable), DISABLE~0,
ENABLE(Enable) ENABLE~1
None Interval Type 0~1,4~5,60~254 N/A None

INPOSITION(In
Position), INPOSITION~0,
None Enumeration Type NOTINPOSITION(N NOTINPOSITION~ None
ot In Position), 1, INVALID~255
INVALID(NULL)
SFP(SFP),
ESFP(ESFP),
SFP~0, ESFP~1,
SFP_ELECTRIC(S
SFP_ELECTRIC~2,
FP_ELECTRIC),
QSFP~3,
None Enumeration Type QSFP(QSFP), None
EQSFP~4,
EQSFP(QSFP_ELE
UNKNOWN~42949
CTRIC),
67295
UNKNOWN(UNKN
OWN)
Character String
Type
SINGLEMODE(SIN
GLEMODE), SINGLEMODE~0,
MULTIMODE(MULT MULTIMODE~1,
IMODE), UNKNOWN~42949
UNKNOWN(UNKN 67295
OWN)
None Interval Type 0~65535 N/A nm
None Interval Type 0~255 N/A 100Mbit/s

None Interval Type 0~255 N/A km
None Interval Type 0~255 N/A 100m

None Interval Type -1280~1280 N/A 0.1 degree Celsius
None Interval Type 0~65535 N/A 100microvolt
None Interval Type 0~65535 N/A 2microampere
None Interval Type 0~65535 N/A 0.1microwatt
None Interval Type 0~65535 N/A 0.1microwatt

UIEB(UIEB),
None Enumeration Type UIEB~9, UTRPc~10 None
UTRPc(UTRPc)
Unknown(Unknown
Unknown~0,
), NULL(NULL),
None Enumeration Type NULL~1, Active~2, None
Active(Active),
Standby~3
Standby(Standby)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
Character String
Type

NORMAL(NORMAL
),
INSTALL(INSTALL),
EXPAND(EXPAND)
,
UPGRADE(UPGRA
DE),
NORMAL~0,
TESTING(TESTIN
INSTALL~1,
G),
EXPAND~2,
ExpandStatus1(Exp
UPGRADE~3,
andStatus1),
TESTING~4,
ExpandStatus2(Exp
ExpandStatus1~5,
andStatus2),
ExpandStatus2~6,
ExpandStatus3(Exp
ExpandStatus3~7,
None Enumeration Type andStatus3), None
ExpandStatus4~8,
ExpandStatus4(Exp
ExpandStatus5~9,
andStatus4),
ExpandStatus6~10,
ExpandStatus5(Exp
ExpandStatus7~11,
andStatus5),
ExpandStatus8~12,
ExpandStatus6(Exp
ExpandStatus9~13,
andStatus6),
ExpandStatus10~1
ExpandStatus7(Exp
4
andStatus7),
ExpandStatus8(Exp
andStatus8),
ExpandStatus9(Exp
andStatus9),
ExpandStatus10(Ex
pandStatus10)
2000-01-
01T00:00:00+00:00
None Compound Type N/A None
~2037-12-
31T23:59:59+00:00
2000-01-
01T00:00:00+00:00
~2037-12-
31T23:59:59+00:00
Character String
Type
NORMAL(NORMAL
),
INSTALL(INSTALL),
EXPAND(EXPAND)
,
UPGRADE(UPGRA
DE),
NORMAL~0,
TESTING(TESTIN
INSTALL~1,
G),
EXPAND~2,
ExpandStatus1(Exp
UPGRADE~3,
andStatus1),
TESTING~4,
ExpandStatus2(Exp
ExpandStatus1~5,
andStatus2),
ExpandStatus2~6,
ExpandStatus3(Exp
ExpandStatus3~7,
None Enumeration Type andStatus3), None
ExpandStatus4~8,
ExpandStatus4(Exp
ExpandStatus5~9,
andStatus4),
ExpandStatus6~10,
ExpandStatus5(Exp
ExpandStatus7~11,
andStatus5),
ExpandStatus8~12,
ExpandStatus6(Exp
ExpandStatus9~13,
andStatus6),
ExpandStatus10~1
ExpandStatus7(Exp
4
andStatus7),
ExpandStatus8(Exp
andStatus8),
ExpandStatus9(Exp
andStatus9),
ExpandStatus10(Ex
pandStatus10)
None Interval Type 390~480 N/A 0.1V

APM30(APM30),
TMC(TMC),
BBC(BBC), APM30~128,
PS4890(PS4890), TMC~129,
OMB(OMB), BBC~130,
RFC(RFC), PS4890~133,
BTS3900(BTS3900 OMB~134,
), RFC~135,
BTS3900L(BTS390 BTS3900~136,
0L), BTS3900L~137,
BTS3900AL(BTS39 BTS3900AL~138,
00AL), VIRTUAL~142,
VIRTUAL(Virtual TP48600A~154,
Cabinet), ILC29~155
TP48600A(TP4860
0A), ILC29(ILC29)
Character String
Type
Character String
Type

BBU3900(BBU3900
Subrack),
RFU(RFU
Subrack),
PMU(PMU
Subrack), BBU3900~128,
TCU(TCU RFU~129,
Subrack), PMU~130,
FMU(FMU TCU~131,
Subrack), FMU~132,
RRU(RRU RRU~134,
Subrack), EMU~137,
EMU(EMU PICO~147,
Subrack), CCU~148,
PICO(PICO UNKNOW~255
Subrack),
CCU(CCU
Subrack),
UNKNOW(Unknow
Subrack)
Character String
Type
AC220V(AC 220V),
DC-48V(DC -48V),
DC+28V(DC +28V), AC220V~0, DC-
DC+24V(DC +24V), 48V~1, DC+28V~2,
DC-48V-2(DC DC+24V~3, DC-
-48V), AC110V(AC 48V-2~4,
110V), RDC- AC110V~5, RDC-
48V(RDC -48V), 48V~6, NDC-48V~7
NDC-48V(NDC
-48V)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Interval Type -20~80 N/A degree Celsius
Monitoring
Environment
Monitoring
Environment
Interval Type 0~100 N/A %
Monitoring
Environment
Monitoring
48V_DISABLE(-48
Voltage Disabled),
RES0(Reserved
Sensor 0),
RES1(Reserved
48V_DISABLE~0,
Sensor 1),
RES0~1, RES1~2,
Environment RES2(Reserved
Bit Field Type RES2~3, None
Monitoring Sensor 2),
TS_DISABLE~4,
TS_DISABLE(Temp
HS_DISABLE~5
erature Sensor
Disabled),
HS_DISABLE(Humi
dity Sensor
Disabled)
WS_DISABLE(Wat
er -Immersed
Sensor Disabled),
SS_DISABLE(Smo
WS_DISABLE~0,
g Sensor Disabled),
Environment SS_DISABLE~1,
Bit Field Type IS_DISABLE(Infrar None
Monitoring IS_DISABLE~2,
ed Sensor
GS_DISABLE~3
Disabled),
GS_DISABLE(Gati
ng Sensor
Disabled)
-
Environment
Interval Type 2147483648~2147 N/A degree Celsius
Monitoring
483647
Environment
Monitoring
Environment Character String

1~7 characters N/A V
Monitoring Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
WS_DISABLE(Wat
er-Immersed
WS_DISABLE~0,
SS_DISABLE~1
SS_DISABLE(Smo
g Sensor Disabled)
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Interval Type 0~4294967295 N/A r/min
Monitoring
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
None Interval Type 8,14 N/A None

Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
WS_DISABLE(Wat
er-Immersed
WS_DISABLE~0,
SS_DISABLE~1
SS_DISABLE(Smo
g Sensor Disabled)
Character String
Type
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
None Interval Type 0~4294967295 N/A r/min
None Interval Type 0~4294967295 N/A r/min
None Interval Type 0~4294967295 N/A W

Character String
Type
Character String
Type
Character String
Type
dantherm(dantherm
), bw(b + w),
huawei(huawei),
air-sys(air-sys),
dantherm~0, bw~1,
senguang(senguan
huawei~2, air-
g),
sys~3,
viasystems(viasyste
senguang~4,
ms), rittal(rittal),
viasystems~5,
emerson(emerson),
rittal~6, emerson~7,
APW(APW),
APW~8, hytems~9,
hytems(hytems),
hontech~10,
hontech(hontech),
None Enumeration Type agisson~11, None
agisson(agisson),
pantair~12,
pantair(pantair),
Panasonic~13,
Panasonic(Panaso
Gore~14, Flex~15,
nic), Gore(Gore),
Vapel~16, AVC~17,
Flex(Flex),
JIAYI~18, Delta~19,
Vapel(Vapel),
EBM~20,
AVC(AVC),
Protechnic~21,
JIAYI(JIAYI),
Sanyo~22
Delta(Delta),
EBM(EBM),
Protechnic(Protech
nic), Sanyo(Sanyo)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
None Interval Type 8,14 N/A None
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
APM100(APM 100),
APM200(APM 200),
APM30(APM 30), APM100~0,
EPS4890(EPS4890 APM200~1,
), APM30~2,
EPS4815(EPS4815 EPS4890~3,
Environment
Enumeration Type ), EPS4815~4, None
Monitoring
SC48200(SC48200 SC48200~5,
), EPS48200~7,
EPS48200(EPS482 TP48300A~8,
00), ETP~10
TP48300A(TP4830
0A), ETP(ETP)
Environment
Interval Type 60~300 N/A V
Monitoring
Environment
Monitoring
Environment
Interval Type 350~556 N/A 0.1V
Monitoring
Environment
Monitoring
Environment DISABLE(Disable), DISABLE~0,
Monitoring ENABLE(Enable) ENABLE~1
Environment
Monitoring
Environment
Monitoring
Environment
Monitoring
BT1_DISABLE(Batt
ery Temperature
Sensor 1 Disabled),
AH_DISABLE(Cabi
net Humidity BT1_DISABLE~0,
Environment Sensor Disabled), AH_DISABLE~1,
Bit Field Type None
Monitoring AT1_DISABLE(Cabi AT1_DISABLE~2,
net Temperature BT2_DISABLE~3
Sensor 1 Disabled),
BT2_DISABLE(Batt
ery Temperature
Sensor 2 Disabled)
WS_DISABLE(Wat
er-Immersed
Sensor Disabled),
WS_DISABLE~0,
Environment SS_DISABLE(Smo
Bit Field Type SS_DISABLE~1, None
Monitoring g Sensor Disabled),
GS_DISABLE~2
GS_DISABLE(Gati
ng Sensor
Disabled)
-
Environment
Monitoring
483647

1~7 characters N/A V
Monitoring Type

1~7 characters N/A A
Monitoring Type
-
Environment
Monitoring
483647
Environment
Monitoring
PowerOn(Power
on),
LowVoltagePowerO
ff(Low voltage
PowerOn~0,
power off),
LowVoltagePowerO
MasterControlPowe
ff~1,
rOff(Master control
MasterControlPowe
Environment power off),
Enumeration Type rOff~2, None
Monitoring HighTemperaturePo
HighTemperaturePo
werOff(High
werOff~3,
temperature power
LowTemperaturePo
off),
werOff~4
LowTemperaturePo
werOff(Low
temperature power
off)
BoostCharging(Boo
st-Charging),
FloatCharging(Float
BoostCharging~0,
-Charging),
FloatCharging~1,
Environment ForceBoostChargin
Enumeration Type ForceBoostChargin None
Monitoring g(ForceBoost-
g~2, Discharging~3,
Charging),
Sleeping~4
Discharging(Discha
rging),
Sleeping(Sleeping)

1~7 characters N/A A
Monitoring Type
CurrentLimiting(Cur
CurrentLimiting~0,
Environment rent limiting),
Enumeration Type NoCurrentLimiting~ None
Monitoring NoCurrentLimiting(
1
No current limiting)
PowerOn(Power
on),
LowVoltagePowerO
ff(Low voltage PowerOn~0,
power off), LowVoltagePowerO
MasterControlPowe ff~1,
Environment rOff(Master control MasterControlPowe
Monitoring power off), rOff~2,
ManualPowerOff(M ManualPowerOff~3,
anual power off), HighTemperaturePo
HighTemperaturePo werOff~4
werOff(High
temperature power
off)
Environment
Monitoring
-
Environment
Monitoring
483647
CHARGE(Charging
),
CHARGE~0,
DISCHARGE(Disch
None Enumeration Type DISCHARGE~1, None
arging),
REC~2, END~3
REC(Recording),
END(Finished)
Character String
None 1~7 characters N/A A
Type
Character String
Type
-
483647
Character String
Type
Character String
Type
Character String
Type
LimiTed),
Kehua(Kehua
Communication
Power Co.,Ltd),
DeltaElectronics(De
lta Electronics
Power(Dong guan)
LTD.),
EltekEnergy(Eltek
Energy
Huawei~0,
Technology(Dong
Emerson~1,
Guan)Ltd.),
Holdluck-ZYT~2,
Switchtec(Hangzho
Power-One~3,
u Switchtec Power
Kehua~4,
Systems Co.,LTD.),
DeltaElectronics~5,
TycoElectronics(Tyc
EltekEnergy~6,
o Electronics
Switchtec~7,
(Shang hai)
TycoElectronics~8,
Co.,Ltd.),
None Enumeration Type ARTESYN~9, None
ARTESYN(Artesyn
CHROMA~10,
Technologies
LuckyValley~11,
Co.,Ltd.),
ACBEL~12,
CHROMA(Chroma
Zippy~13,
Electronics),
GuoyaoElectronics
LuckyValley(Lucky
~14, DPC~15,
Valley Technology
GoldPower~16,
Co.,Ltd),
SungrowPowerSup
ACBEL(Acbel
ply~17, Ecom~18
Electronic Co.,Ltd),
Zippy(Zippy
Technology corp.),
GuoyaoElectronics(
Shenzhen Guoyao
Electronics
Technology
Co.,LTD.),
DPC(Beijing
Dynamic Power
UNSUPPORTED(N
ot Supported), UNSUPPORTED~0
SUPPORTED(Supp , SUPPORTED~1
orted)
SUCCEEDED(Succ
eeded),
BRDNOTREADY(T
he board is
unavailable),
SUCCEEDED~0,
UNSUPPORTED(T
BRDNOTREADY~1
he PSU intelligent
,
None Enumeration Type shutdown is not None
UNSUPPORTED~2
supported by the
, BATNOTEXIST~3,
board),
INTERNALERR~4
BATNOTEXIST(The
battery does not
exist),
INTERNALERR(Int
ernal error)
UNSUPPORTED(N
ot Supported), UNSUPPORTED~0
SUPPORTED(Supp , SUPPORTED~1
orted)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

None Interval Type 1~1000 N/A 0.1kVA
Character String
None 1~7 characters N/A cm
Type
Character String
Type

INNER(Inner), INNER~0,
OUTER(Outer) OUTER~1
None Interval Type 30~240 N/A day

None Interval Type 5~5000 N/A Ah
None Interval Type 5~25 N/A 0.01

None Interval Type 0~500 N/A mV/degree Celsius

None Interval Type -20~20 N/A degree Celsius
VRLA_BAT(VRLA
VRLA_BAT~2,
None Enumeration Type Battery), LI_BAT(Li- None
LI_BAT~3
Ion Battery)



2000-01-01~2099-
12-31

None Interval Type 1~5000 N/A 0.01h





None Interval Type 170~220 N/A 0.01V/cell

NOAUTOTEST(No
Auto Test),
PERIOD(Period
NOAUTOTEST~0,
Auto Test),
PERIOD~1,
POWERCUT(Powe
None Enumeration Type POWERCUT~2, None
r Off Auto Test),
PERIODPOWERC
PERIODPOWERC
UT~3
UT(Period and
Power Off Auto
Test)

STANDARD(Standa
rd Test),
SIMPLE(Simple STANDARD~0,
Test), SIMPLE~1,
None Enumeration Type TIMER(Period TIMER~2, None
Test), PWROFF~3,
PWROFF(Power NONE~4
Cut Test),
NONE(None Test)
2000-01-01
None Compound Type 00:00:00~2038-12- N/A None
31 23:59:59
BelowEndVol(Lower
Than End Voltage),
OverTime(Test
Timeout),
BelowEndVol~0,
CurrRecover(Power
OverTime~1,
Resume Stop
None Enumeration Type CurrRecover~2, None
Power Drop Auto
ManualEnd~3,
Test),
AlmEnd~4
ManualEnd(Manual
Stop Test),
AlmEnd(Alarm Stop
Test)
None(No result),
Normal(Battery
normal), None~0, Normal~1,
PreAlm(Battery pre- PreAlm~2, Alm~3
alarm), Alm(Battery
alarm)
Character String
None 1~7 characters N/A h
Type
Character String
None 1~7 characters N/A V
Type
Character String
Type
-
483647

NORMAL(Normal),
COMMUNICATEFAI
LED(Communicatio NORMAL~0,
n failed), COMMUNICATEFAI
SHUTDOWN(Shut LED~1,
down), SHUTDOWN~2,
FAULT(Fault), FAULT~3,
PROTECT(Fault), PROTECT~4,
UNCONFIGURED( UNCONFIGURED~
Unconfigured), 5, ILLEGAL~6
ILLEGAL(Unconfigu
red)
Character String
Type
LimiTed),
Kehua(Kehua
Communication
Power Co.,Ltd),
DeltaElectronics(De
lta Electronics
Power(Dong guan)
LTD.),
EltekEnergy(Eltek
Energy
Huawei~0,
Technology(Dong
Emerson~1,
Guan)Ltd.),
Holdluck-ZYT~2,
Switchtec(Hangzho
Power-One~3,
u Switchtec Power
Kehua~4,
Systems Co.,LTD.),
DeltaElectronics~5,
TycoElectronics(Tyc
EltekEnergy~6,
o Electronics
Switchtec~7,
(Shang hai)
TycoElectronics~8,
Co.,Ltd.),
None Enumeration Type ARTESYN~9, None
ARTESYN(Artesyn
CHROMA~10,
Technologies
LuckyValley~11,
Co.,Ltd.),
ACBEL~12,
CHROMA(Chroma
Zippy~13,
Electronics),
GuoyaoElectronics
LuckyValley(Lucky
~14, DPC~15,
Valley Technology
GoldPower~16,
Co.,Ltd),
SungrowPowerSup
ACBEL(Acbel
ply~17, Ecom~18
Electronic Co.,Ltd),
Zippy(Zippy
Technology corp.),
GuoyaoElectronics(
Shenzhen Guoyao
Electronics
Technology
Co.,LTD.),
DPC(Beijing
Dynamic Power
Character String
Type
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

Monitoring Type
Environment
Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Monitoring
0~1,7~8,11~12,14~
None Interval Type N/A None
15,40~254
Environment
Monitoring
Environment
Monitoring
BOOL(Digital Port),
Environment
Enumeration Type VALUE(Analog BOOL~0, VALUE~1 None
Monitoring
Port)
HIGH(High
Environment
Enumeration Type Voltage), LOW(Low HIGH~0, LOW~1 None
Monitoring
Voltage)
Environment
Interval Type -99999~999999 N/A 0.01
Monitoring
Environment
Interval Type -99999~999999 N/A 0.01
Monitoring
VOLTAGE(Voltage
Environment Type), VOLTAGE~0,
Monitoring CURRENT(Current CURRENT~1
Type)
Environment
Interval Type -99999~999999 N/A 0.01
Monitoring
Environment
Interval Type -99999~999999 N/A 0.01
Monitoring
Environment
Interval Type 0~999999 N/A 0.01V or 0.01mA
Monitoring
Environment
Interval Type 0~999999 N/A 0.01V or 0.01mA
Monitoring
ALL(All Type),
None Enumeration Type ALL~0, SSL~1 None
SSL(Only SSL)
NONE(Verify
None Enumeration Type None), PEER(Verify NONE~0, PEER~1 None
Peer Certificate)

Character String
Type
None Enumeration Type MAAU(MAAU) MAAU~35 None
BLOCKED(Blocked
), BLOCKED~0,
ocked)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)

None Enumeration Type TRUNK(TRUNK) TRUNK~0 None

TD_SCDMA(TD_S
CDMA),
LTE_TDD(LTE_TD
D),
TDS_TDL(TDS_TD
TD_SCDMA~2,
L),
LTE_TDD~4,
LTE_FDD(LTE_FD
TDS_TDL~6,
D),
LTE_FDD~8,
WiMAX_LTE(WiMA
None Enumeration Type WiMAX_LTE~20, None
X_LTE),
CDMA_LTE~40,
CDMA_LTE(CDMA
GSM_LTE~72,
_LTE),
UMTS_ONLY~128,
GSM_LTE(GSM_LT
UMTS_LTE~136
E),
UMTS_ONLY(UMT
S_ONLY),
UMTS_LTE(UMTS_
LTE)
None Interval Type 0~4294967295 N/A 0.1MHz

Character String
None 0~31 characters N/A MHz
Type
Character String
Type
LO_TD(LO_TD),
TL(TL), LO(LO),
WO(WO), WL(WL),
LO_TD~4, TL~6,
C0(C0), CL(CL),
LO~8, WO~16,
CW(CW),
WL~20, C0~32,
CWL(CWL),
CL~40, CW~48,
GO(GO), GL(GL),
CWL~56, GO~64,
GW(GW),
GL~72, GW~80,
GWL(GWL),
GWL~88, GC~96,
GC(GC),
GCL~104,
GCL(GCL),
GCW~112,
GCW(GCW),
GCWL~120,
GCWL(GCWL),
UO~128, UL~136,
UO(UO), UL(UL),
UW~144,
None Enumeration Type UW(UW), None
UWL~152,
UWL(UWL),
UC~160, UCL~168,
UC(UC),
UCW~176,
UCL(UCL),
UCWL~184,
UCW(UCW),
GU~192, UGL~200,
UCWL(UCWL),
UGW~208,
GU(GU),
UGWL~216,
UGL(UGL),
UGC~224,
UGW(UGW),
UGCL~232,
UGWL(UGWL),
UGCW~240,
UGC(UGC),
UGCWL~248,
UGCL(UGCL),
NULL~255
UGCW(UGCW),
UGCWL(UGCWL),
NULL(Invalid)
CONNECTHEAD(A
ccess from chain
head or ring head),
CONNECTTAIL(Ac CONNECTHEAD~0
cess from ring tail), , CONNECTTAIL~1,
CONNECTBOTH(A CONNECTBOTH~2
None Enumeration Type ccess from both , None
ends of the ring), SEPERATEBYBRE
SEPERATEBYBRE AK~3,
AK(Seperated by LINKDOWN~4
break points),
LINKDOWN(Link
down)
Character String
Type
POW_IQ_MODE(P
OW_IQ_MODE),
POW_IQ_MODE~0
POW_MODE(POW
None Enumeration Type , POW_MODE~1, None
_MODE),
IQ_MODE~2
IQ_MODE(IQ_MOD
E)
HALFSECOND(HA
LFSECOND),
ONESECOND(ONE
HALFSECOND~5,
SECOND),
ONESECOND~10,
TWOSECOND(TW
TWOSECOND~20,
OSECOND),
None Enumeration Type THREESECOND~3 None
THREESECOND(T
0,
HREESECOND),
FOURSECOND~40
FOURSECOND(FO
, FIVESECOND~50
URSECOND),
FIVESECOND(FIV
ESECOND)

Character String
Type
SUCCESS(SUCCE
SS), SUCCESS~0,
FAILURE(FAILURE FAILURE~1,
), UNKNOWTYPE~25
UNKNOWTYPE(Un 5
know Type)
USERDEFINE(USE
RDEFINE), USERDEFINE~0,
T)
1.25G(1.25G),
2.5G(2.5G),
1.25G~1, 2.5G~2,
3.0G(3.0G),
None Enumeration Type 3.0G~4, 4.9G~8, bit/s
4.9G(4.9G),
6.1G~16, 9.8G~32
6.1G(6.1G),
9.8G(9.8G)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
BLOCKED(Blocked
), BLOCKED~0,
ocked)


TD_SCDMA(TD_S
CDMA),
LTE_TDD(LTE_TD
D),
TDS_TDL(TDS_TD
TD_SCDMA~2,
L),
LTE_TDD~4,
LTE_FDD(LTE_FD
TDS_TDL~6,
D),
LTE_FDD~8,
WiMAX_LTE(WiMA
X_LTE),
CDMA_LTE~40,
CDMA_LTE(CDMA
GSM_LTE~72,
_LTE),
UMTS_ONLY~128,
GSM_LTE(GSM_LT
UMTS_LTE~136
E),
UMTS_ONLY(UMT
S_ONLY),
UMTS_LTE(UMTS_
LTE)

Character String
Type
Character String
Type
LO_TD(LO_TD),
TL(TL), LO(LO),
WO(WO), WL(WL),
LO_TD~4, TL~6,
C0(C0), CL(CL),
LO~8, WO~16,
CW(CW),
WL~20, C0~32,
CWL(CWL),
CL~40, CW~48,
GO(GO), GL(GL),
CWL~56, GO~64,
GW(GW),
GL~72, GW~80,
GWL(GWL),
GWL~88, GC~96,
GC(GC),
GCL~104,
GCL(GCL),
GCW~112,
GCW(GCW),
GCWL~120,
GCWL(GCWL),
UO~128, UL~136,
UO(UO), UL(UL),
UW~144,
UWL~152,
UWL(UWL),
UC~160, UCL~168,
UC(UC),
UCW~176,
UCL(UCL),
UCWL~184,
UCW(UCW),
GU~192, UGL~200,
UCWL(UCWL),
UGW~208,
GU(GU),
UGWL~216,
UGL(UGL),
UGC~224,
UGW(UGW),
UGCL~232,
UGWL(UGWL),
UGCW~240,
UGC(UGC),
UGCWL~248,
UGCL(UGCL),
NULL~255
UGCW(UGCW),
UGCWL(UGCWL),
NULL(Invalid)
CONNECTHEAD(A
ccess from chain
head or ring head),
SEPERATEBYBRE AK~3,
break points),
LINKDOWN(Link
down)
Character String
Type
POW_IQ_MODE(P
OW_IQ_MODE),
POW_IQ_MODE~0
POW_MODE(POW
_MODE),
IQ_MODE~2
IQ_MODE(IQ_MOD
E)
HALFSECOND(HA
LFSECOND),
ONESECOND(ONE
HALFSECOND~5,
SECOND),
ONESECOND~10,
TWOSECOND(TW
TWOSECOND~20,
OSECOND),
THREESECOND(T
0,
HREESECOND),
FOURSECOND~40
FOURSECOND(FO
, FIVESECOND~50
URSECOND),
FIVESECOND(FIV
ESECOND)

Character String
Type
SUCCESS(SUCCE
SS), SUCCESS~0,
), UNKNOWTYPE~25
UNKNOWTYPE(Un 5
know Type)
USERDEFINE(USE
T)
1.25G(1.25G),
2.5G(2.5G),
1.25G~1, 2.5G~2,
3.0G(3.0G),
4.9G(4.9G),
6.1G~16, 9.8G~32
6.1G(6.1G),
9.8G(9.8G)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
MRFU(MRFU), MRFU~16,
LRFU(LRFU) LRFU~12304
BLOCKED(Blocked
), BLOCKED~0,
ocked)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)


TD_SCDMA(TD_S
CDMA),
LTE_TDD(LTE_TD
D),
TDS_TDL(TDS_TD
TD_SCDMA~2,
L),
LTE_TDD~4,
LTE_FDD(LTE_FD
TDS_TDL~6,
D),
LTE_FDD~8,
WiMAX_LTE(WiMA
X_LTE),
CDMA_LTE~40,
CDMA_LTE(CDMA
GSM_LTE~72,
_LTE),
UMTS_ONLY~128,
GSM_LTE(GSM_LT
UMTS_LTE~136
E),
UMTS_ONLY(UMT
S_ONLY),
UMTS_LTE(UMTS_
LTE)

Character String
Type
Character String
Type
LO_TD(LO_TD),
TL(TL), LO(LO),
WO(WO), WL(WL),
LO_TD~4, TL~6,
C0(C0), CL(CL),
LO~8, WO~16,
CW(CW),
WL~20, C0~32,
CWL(CWL),
CL~40, CW~48,
GO(GO), GL(GL),
CWL~56, GO~64,
GW(GW),
GL~72, GW~80,
GWL(GWL),
GWL~88, GC~96,
GC(GC),
GCL~104,
GCL(GCL),
GCW~112,
GCW(GCW),
GCWL~120,
GCWL(GCWL),
UO~128, UL~136,
UO(UO), UL(UL),
UW~144,
UWL~152,
UWL(UWL),
UC~160, UCL~168,
UC(UC),
UCW~176,
UCL(UCL),
UCWL~184,
UCW(UCW),
GU~192, UGL~200,
UCWL(UCWL),
UGW~208,
GU(GU),
UGWL~216,
UGL(UGL),
UGC~224,
UGW(UGW),
UGCL~232,
UGWL(UGWL),
UGCW~240,
UGC(UGC),
UGCWL~248,
UGCL(UGCL),
NULL~255
UGCW(UGCW),
UGCWL(UGCWL),
NULL(Invalid)
CONNECTHEAD(A
ccess from chain
head or ring head),
SEPERATEBYBRE AK~3,
break points),
LINKDOWN(Link
down)
Character String
Type
POW_IQ_MODE(P
OW_IQ_MODE),
POW_IQ_MODE~0
POW_MODE(POW
_MODE),
IQ_MODE~2
IQ_MODE(IQ_MOD
E)
HALFSECOND(HA
LFSECOND),
ONESECOND(ONE
HALFSECOND~5,
SECOND),
ONESECOND~10,
TWOSECOND(TW
TWOSECOND~20,
OSECOND),
THREESECOND(T
0,
HREESECOND),
FOURSECOND~40
FOURSECOND(FO
, FIVESECOND~50
URSECOND),
FIVESECOND(FIV
ESECOND)

Character String
Type
SUCCESS(SUCCE
SS), SUCCESS~0,
), UNKNOWTYPE~25
UNKNOWTYPE(Un 5
know Type)
USERDEFINE(USE
T)
1.25G(1.25G),
2.5G(2.5G),
1.25G~1, 2.5G~2,
3.0G(3.0G),
4.9G(4.9G),
6.1G~16, 9.8G~32
6.1G(6.1G),
9.8G(9.8G)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)
Character String
Type
MRRU(MRRU), MRRU~15,
None Enumeration Type PRRU(PRRU), PRRU~271, None
LRRU(LRRU) LRRU~12303
PIMOFFLINE(PIMO
None Enumeration Type PIMOFFLINE~0 None
FFLINE)
None Interval Type 5~20 N/A dB
IsInerefered(It is
Interfered), IsInerefered~0,
IsNotInterfered(It is IsNotInterfered~1
not interfered)
BLOCKED(Blocked
), BLOCKED~0,
ocked)
Avail_0~0,
Avail_801(Fault,
Avail_1~1,
Communication
Avail_20~32,
lost),
Avail_21~33,
Avail_820(Commun
Avail_500~1280,
Avail_501~1281,
Avail_821(Fault,
Avail_504~1284,
Communication
Avail_508~1288,
lost, In test),
Avail_509~1289,
Avail_c10(Power
Avail_520~1312,
off),
Avail_521~1313,
Avail_c11(Power
Avail_524~1316,
off, Fault),
Avail_528~1320,
Avail_c12(Uninstall
Avail_529~1321,
ed),
Avail_800~2048,
Avail_c13(Uninstall
Avail_801~2049,
ed, Fault),
Avail_820~2080,
Avail_c14(Unconfig
Avail_821~2081,
ured, Power off),
Avail_c10~3088,
Avail_c11~3089,
off,In test),
Avail_c12~3090,
Avail_c31(Power
Avail_c13~3091,
Avail_c14~3092,
Avail_c32(Uninstall
Avail_c30~3120,
ed,In test),
Avail_c31~3121,
Avail_c33(Uninstall
Avail_c32~3122,
Avail_c33~3123,
Avail_c34(Unconfig
Avail_c34~3124,
ured, Power off, In
Avail_d00~3328,
test),
Avail_d01~3329,
Avail_d00(Commun
Avail_d04~3332,
ication lost),
Avail_d08~3336,
Avail_d01(Starting
Avail_d09~3337,
up, Fault,
Avail_d20~3360,
Communication
Avail_d21~3361,
lost),
Avail_d24~3364,
Avail_d04(Unconfig
Avail_d28~3368,
ured,
Avail_d29~3369
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type UMPT(UMPT),
FAN(FAN),
UPEU(UPEU),
PMU(PMU),
UMPT~1, FAN~3,
PSU(PSU),
UPEU~4, PMU~5,
BAT(BAT),
PSU~6, BAT~7,
TCU(TCU),
TCU~8, EMU~10,
EMU(EMU),
UTRP~11,
UTRP(UTRP),
USCU~12,
USCU(USCU),
UEIU~13, FMU~14,
UEIU(UEIU),
MRRU~15,
FMU(FMU),
MRFU~16,
MRRU(MRRU),
RHUB~17,
MRFU(MRFU),
UBRI~20,
RHUB(RHUB),
MRXU~22,
UBRI(UBRI),
MTXU~23,
MRXU(MRXU),
UCIU~24, CCU~25,
MTXU(MTXU),
MAAU~35,
UCIU(UCIU),
CCU(CCU),
PRRU~271,
MAAU(MAAU),
GRRU~4111,
UNKNOWN(UNKN
GRFU~4112,
OWN),
GATM~4114,
PRRU(PRRU),
DRRU~4367,
GRRU(GRRU),
DRFU~4368,
GRFU(GRFU),
WRFU~8208,
GATM(GATM),
NGRU~8211,
DRRU(DRRU),
LMPT~12289,
DRFU(DRFU),
LBBP~12290,
WRFU(WRFU),
LRRU~12303,
NGRU(NGRU),
LRFU~12304,
LMPT(LMPT),
BRFU~16400,
LBBP(LBBP),
CRFU~20496,
LRRU(LRRU),
RRU~24591
LRFU(LRFU),
BRFU(BRFU),
CRFU(CRFU),
RRU(RRU)
CPU(CPU),
DSP(DSP),
CPU), SLAVE_CPU~3,
PU), MRU_CPU~5
MRU_CPU(MRU_C
PU)
-
483647
-
483647
Character String
Type
Master(Master),
NDD(NDD),
EDL(EDL),
Slave(Slave)
CABINET(CABINE
T), CABINET~0,
SUBBOARD(SUBB SFP~4
OARD), SFP(SFP)


TD_SCDMA(TD_S
CDMA),
LTE_TDD(LTE_TD
D),
TDS_TDL(TDS_TD
TD_SCDMA~2,
L),
LTE_TDD~4,
LTE_FDD(LTE_FD
TDS_TDL~6,
D),
LTE_FDD~8,
WiMAX_LTE(WiMA
X_LTE),
CDMA_LTE~40,
CDMA_LTE(CDMA
GSM_LTE~72,
_LTE),
UMTS_ONLY~128,
GSM_LTE(GSM_LT
UMTS_LTE~136
E),
UMTS_ONLY(UMT
S_ONLY),
UMTS_LTE(UMTS_
LTE)

Character String
Type
Character String
Type
LO_TD(LO_TD),
TL(TL), LO(LO),
WO(WO), WL(WL),
LO_TD~4, TL~6,
C0(C0), CL(CL),
LO~8, WO~16,
CW(CW),
WL~20, C0~32,
CWL(CWL),
CL~40, CW~48,
GO(GO), GL(GL),
CWL~56, GO~64,
GW(GW),
GL~72, GW~80,
GWL(GWL),
GWL~88, GC~96,
GC(GC),
GCL~104,
GCL(GCL),
GCW~112,
GCW(GCW),
GCWL~120,
GCWL(GCWL),
UO~128, UL~136,
UO(UO), UL(UL),
UW~144,
UWL~152,
UWL(UWL),
UC~160, UCL~168,
UC(UC),
UCW~176,
UCL(UCL),
UCWL~184,
UCW(UCW),
GU~192, UGL~200,
UCWL(UCWL),
UGW~208,
GU(GU),
UGWL~216,
UGL(UGL),
UGC~224,
UGW(UGW),
UGCL~232,
UGWL(UGWL),
UGCW~240,
UGC(UGC),
UGCWL~248,
UGCL(UGCL),
NULL~255
UGCW(UGCW),
UGCWL(UGCWL),
NULL(Invalid)
CONNECTHEAD(A
ccess from chain
head or ring head),
SEPERATEBYBRE AK~3,
break points),
LINKDOWN(Link
down)
Character String
Type
POW_IQ_MODE(P
OW_IQ_MODE),
POW_IQ_MODE~0
POW_MODE(POW
_MODE),
IQ_MODE~2
IQ_MODE(IQ_MOD
E)
HALFSECOND(HA
LFSECOND),
ONESECOND(ONE
HALFSECOND~5,
SECOND),
ONESECOND~10,
TWOSECOND(TW
TWOSECOND~20,
OSECOND),
THREESECOND(T
0,
HREESECOND),
FOURSECOND~40
FOURSECOND(FO
, FIVESECOND~50
URSECOND),
FIVESECOND(FIV
ESECOND)

Character String
Type
SUCCESS(SUCCE
SS), SUCCESS~0,
), UNKNOWTYPE~25
UNKNOWTYPE(Un 5
know Type)
USERDEFINE(USE
T)
1.25G(1.25G),
2.5G(2.5G),
1.25G~1, 2.5G~2,
3.0G(3.0G),
4.9G(4.9G),
6.1G~16, 9.8G~32
6.1G(6.1G),
9.8G(9.8G)
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Character String
Type
Normal(Normal),
Normal~0, Fault~1,
Fault(Fault),
Timeout(Timeout),
NULL~4294967295
NULL(NULL)

CHAIN(CHAIN),
RING(RING), CHAIN~0, RING~1,
LOADBALANCE(L LOADBALANCE~2
OADBALANCE)
COLD(COLD),
None Enumeration Type COLD~0, HOT~1 None
HOT(HOT)
LOCALPORT(local
port), LOCALPORT~0,
PEERPORT(peer PEERPORT~1
port)
1.25G(1.25),
2.5G(2.5),
1.25G~0, 2.5G~1,
4.9G(4.9),
None Enumeration Type 4.9G~3, 6.1G~4, Gbit/s
6.1G(6.1),
9.8G~5, AUTO~255
9.8G(9.8),
AUTO(Auto)


Character String
Type
Character String
Type



None Interval Type -100~10 N/A 0.1dB

Character String
Type
None Interval Type 0,500~65500 N/A 10mW

Character String
Type

Character String
Type
Normal(Normal),
Normal~0,
Unknown(Unknown
None Enumeration Type Unknown~1, None
),
Crossed~2
Crossed(Crossed)

123~5999,6100~65
None Interval Type N/A None
534
IPV4(IPv4),
None Enumeration Type IPV4~0, IPV6~1 None
IPV6(IPv6)
PLAIN(Plain),
PLAIN~0,
DES_S(DES_S),
DES_S~1,
None Enumeration Type DES_N(DES_N), None
DES_N~2,
DES_A(DES_A),
DES_A~3, MD5~4
MD5(MD5)
None Password Type 1~16 characters N/A None
Slaver(Slave),
None Enumeration Type Slaver~0, Master~1 None
Master(Master)
1100~4, GMT-
GMT-0300(GMT-
1000~8, GMT-
03:00), GMT-
0930~10, GMT-
0200(GMT-02:00),
0900~12, GMT-
GMT-0100(GMT-
0800~16, GMT-
01:00), GMT(GMT),
0700~20, GMT-
GMT+0100(GMT+0
0600~24, GMT-
1:00),
0500~28, GMT-
GMT+0200(GMT+0
0430~30, GMT-
2:00),
0400~32, GMT-
GMT+0300(GMT+0
0330~34, GMT-
3:00),
0300~36, GMT-
GMT+0330(GMT+0
0200~40, GMT-
3:30),
0100~44, GMT~48,
GMT+0400(GMT+0
GMT+0100~52,
4:00),
GMT+0200~56,
GMT+0430(GMT+0
GMT+0300~60,
4:30),
GMT+0330~62,
GMT+0500(GMT+0
GMT+0400~64,
None Enumeration Type 5:00), None
GMT+0430~66,
GMT+0530(GMT+0
GMT+0500~68,
5:30),
GMT+0530~70,
GMT+0545(GMT+0
GMT+0545~71,
5:45),
GMT+0600~72,
GMT+0600(GMT+0
GMT+0630~74,
6:00),
GMT+0700~76,
GMT+0630(GMT+0
GMT+0800~80,
6:30),
GMT+0845~83,
GMT+0700(GMT+0
GMT+0900~84,
7:00),
GMT+0930~86,
GMT+0800(GMT+0
GMT+1000~88,
8:00),
GMT+1030~90,
GMT+0845(GMT+0
GMT+1100~92,
8:45),
GMT+1130~94,
GMT+0900(GMT+0
GMT+1200~96,
9:00),
GMT+1245~99,
GMT+0930(GMT+0
GMT+1300~100,
9:30),
GMT+1400~104,
None Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None

DATE(Date mode),
WEEK(Week
DATE~0, WEEK~1,
None Enumeration Type mode), None
DATEWEEK~2
DATEWEEK(Date
and week mode)
JAN(January),
FEB(February),
MAR(March),
APR(April), JAN~1, FEB~2,
MAY(May), MAR~3, APR~4,
JUN(June), MAY~5, JUN~6,
JUL(July), JUL~7, AUG~8,
AUG(August), SEP~9, OCT~10,
SEP(September), NOV~11, DEC~12
OCT(October),
NOV(November),
DEC(December)

LAST(Last),
LAST~0, FIRST~1,
FIRST(First),
SECOND~2,
None Enumeration Type SECOND(Second), None
THIRD~3,
THIRD(Third),
FOURTH~4
FOURTH(Fourth)
MON(Monday),
TUE(Tuesday),
MON~1, TUE~2,
WED(Wednesday),
WED~3, THU~4,
None Enumeration Type THU(Thursday), None
FRI~5, SAT~6,
FRI(Friday),
SUN~7
SAT(Saturday),
SUN(Sunday)
None Compound Type 00:00:00~23:59:59 N/A None
DATE(Date mode),
WEEK(Week
DATE~0, WEEK~1,
None Enumeration Type mode), None
DATEWEEK~2
DATEWEEK(Date
and week mode)
JAN(January),
FEB(February),
MAR(March),
APR(April), JAN~1, FEB~2,
MAY(May), MAR~3, APR~4,
JUN(June), MAY~5, JUN~6,
JUL(July), JUL~7, AUG~8,
AUG(August), SEP~9, OCT~10,
SEP(September), NOV~11, DEC~12
OCT(October),
NOV(November),
DEC(December)
LAST(Last),
LAST~0, FIRST~1,
FIRST(First),
SECOND~2,
None Enumeration Type SECOND(Second), None
THIRD~3,
THIRD(Third),
FOURTH~4
FOURTH(Fourth)
MON(Monday),
TUE(Tuesday),
MON~1, TUE~2,
WED(Wednesday),
WED~3, THU~4,
None Enumeration Type THU(Thursday), None
FRI~5, SAT~6,
FRI(Friday),
SUN~7
SAT(Saturday),
SUN(Sunday)
None Interval Type -120~120 N/A min

None Interval Type -720~840 N/A min
2000-01-01~2033-
12-31
None Compound Type None N/A None
NTP(NTP),
NTP~0, GPS~1,
None Enumeration Type GPS(GPS), None
NONE~2
NONE(None)
Character String
Type
Auto(Auto),
Auto~0,
Plaintext(Plaintext),
None Enumeration Type Plaintext~1, None
Encrypted(SSL
Encrypted~2
Encrypted)
None Enumeration Type No(No), Yes(Yes) No~0, Yes~1 None
None Enumeration Type No(No), Yes(Yes) No~0, Yes~1 None

Service based inter-

RAT handover to
UTRAN
RAT handover to
GERAN
Service Based
Inter-frequency Interval Type 0~9 N/A None
Handover

QCI1(QCI 1),
QCI2(QCI 2),
QCI3(QCI 3), QCI1~1, QCI2~2,
None Enumeration Type QCI5(QCI 5), QCI5~5, QCI6~6, None
QCI7(QCI 7), QCI9~9
QCI8(QCI 8),
QCI9(QCI 9)

RAT handover to
UTRAN
RAT handover to
GERAN
Service Based
Handover

PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Inter-RAT Load
Sharing to UTRAN
UTRAN~0,
Inter-RAT Load UTRAN, GERAN,
Enumeration Type GERAN~1, None
Sharing to GERAN CDMA2000
CDMA2000~2
CS Fallback to
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
CS Fallback with
LAI to UTRAN
CS Fallback with
LAI to GERAN
Flash CS Fallback
to UTRAN
Flash CS Fallback
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Inter-RAT Load
Sharing to UTRAN UTRAN~0,
Inter-RAT Load UTRAN, GERAN, GERAN~1,
Sharing to GERAN CDMA2000, NULL CDMA2000~2,
CS Fallback to NULL~3
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
CS Fallback with
LAI to UTRAN
CS Fallback with
LAI to GERAN
Flash CS Fallback
to UTRAN
Flash CS Fallback
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Inter-RAT Load
Sharing to UTRAN UTRAN~0,
Inter-RAT Load UTRAN, GERAN, GERAN~1,
Sharing to GERAN CDMA2000, NULL CDMA2000~2,
CS Fallback to NULL~3
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
CS Fallback with
LAI to UTRAN
CS Fallback with
LAI to GERAN
Flash CS Fallback
to UTRAN
Flash CS Fallback
to GERAN
CS Fallback to
UTRAN
LoCation
Services(LCS)
CS Fallback to
GERAN
LoCation
Services(LCS)
CS Fallback to
CDMA2000 1xRTT
LoCation
Services(LCS)
Handover
Coverage Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000 Character String
3 characters N/A None
Intra-LTE Load Type
Balancing
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
UTRAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to UTRAN
Distance based
inter-RAT handover
to GERAN
Service Based
Handover
Coverage Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
Intra-LTE Load Type
Balancing
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
UTRAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to UTRAN
Distance based
inter-RAT handover
to GERAN
Service Based
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
Flexible User
Steering
Camp & Handover
Based on SPID
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN LTE, UTRAN, LTE~0, UTRAN~1,
Flexible User GERAN GERAN~2
Steering
Camp & Handover
Based on SPID
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN 0~45589,64436~65
Interval Type N/A None
Flexible User 535
Steering
Camp & Handover
Based on SPID
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN GSM_dcs1800, GSM_dcs1800~0,
Flexible User GSM_pcs1900 GSM_pcs1900~1
Steering
Camp & Handover
Based on SPID
Service Based
Handover
Service Based
Handover
Service Based
NO_HO, NO_HO~0,
Inter-frequency Enumeration Type None
PERMIT_HO PERMIT_HO~1
Handover
Service Based
0~45589,64436~65
Inter-frequency Interval Type N/A None
535
Handover

RAT handover to
UTRAN
RAT handover to
GERAN

RAT handover to
UTRAN
RAT handover to
GERAN

RAT handover to
NO_HO, NO_HO~0,
UTRAN
Enumeration Type PERMIT_HO, PERMIT_HO~1, None
MUST_HO MUST_HO~2
RAT handover to
GERAN
Intra-LTE Load
Balancing
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
Flexible User
Steering
Camp & Handover
Based on SPID
UL Pre-allocation
Based on SPID
DRX
FALSE(FALSE),
Flexible User Enumeration Type FALSE~0, TRUE~1 None
TRUE(TRUE)
Steering
Intra-LTE Load
Balancing
Inter-RAT Load
Sharing to UTRAN NOT_CFG(NOT_C NOT_CFG~0,
Inter-RAT Load FG), CFG(CFG) CFG~1
Sharing to GERAN
Flexible User
Steering
Intra-LTE Load
Balancing
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
Flexible User
Steering
Camp & Handover
Based on SPID
UL Pre-allocation
Based on SPID
Flexible User
Steering FALSE(FALSE),
Enumeration Type FALSE~0, TRUE~1 None
UL Pre-allocation TRUE(TRUE)
Based on SPID
Intra-LTE Load
Balancing FALSE(FALSE),
Flexible User TRUE(TRUE)
Steering
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load FALSE(FALSE),
Sharing to GERAN TRUE(TRUE)
Flexible User
Steering
Coverage Based
Inter-frequency
Handover
PS Inter-RAT
Mobility between E- FALSE(FALSE),
UTRAN and TRUE(TRUE)
UTRAN
SRVCC to UTRAN
Flexible User
Steering
Integrity Protection Interval Type 0,10~600 N/A s
Integrity Protection Interval Type 0,128~4294967295 N/A None

Integrity Protection Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
NULL(NULL
Algorithm),
Encryption: AES
Snow3G(SNOW 3G NULL~0,
Encryption: SNOW Enumeration Type None
Algorithm), Snow3G~1, AES~2
3G
AES(AES
Algorithm)
NULL(NULL
Algorithm),
Encryption: AES
3G
AES(AES
Algorithm)
NULL(NULL
Algorithm),
Encryption: AES
3G
AES(AES
Algorithm)
NULL(NULL
Algorithm),
Integrity Protection Enumeration Type None
AES(AES
Algorithm)
NULL(NULL
Algorithm),
AES(AES
Algorithm)
NULL(NULL
Algorithm),
AES(AES
Algorithm)
Mobility
Management
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Mobility
Management X2_OVER_M2000(
Coverage Based X2SonLink is set up
Intra-frequency over M2000), X2_OVER_M2000~
Handover X2_OVER_S1(X2S 0, X2_OVER_S1~1
Coverage Based onLink is set up
Inter-frequency over S1)
Handover
Basic Scheduling
Enhanced
Scheduling Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Physical Channel
Management
LCG_PROFILE_0~
Basic Scheduling
LCG_PROFILE_0, 0,
Enhanced Enumeration Type None
LCG_PROFILE_1 LCG_PROFILE_1~
Scheduling
1
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
RRC Connection
Management
None Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None

RObust Header
Compression Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
(ROHC)
U_MODE(Unidirecti
onal Mode),
O_MODE(Bi-
RObust Header U_MODE~1,
directional
Compression Enumeration Type O_MODE~2, None
Optimistic Mode),
(ROHC) R_MODE~3
R_MODE(Bi-
Directional Reliable
Mode)
Profile0x0001(Profil
e0x0001),
Profile0x0002(Profil Profile0x0001~0,
RObust Header
e0x0002), Profile0x0002~1,
Compression Bit Field Type None
Profile0x0003(Profil Profile0x0003~2,
(ROHC)
e0x0003), Profile0x0004~3
Profile0x0004(Profil
e0x0004)
RRC Connection
Interval Type 1~16 N/A s
Management
min5(5), min10(10),
min5~0, min10~1,
Mobility min20(20),
min20~2, min30~3,
Management min30(30),
Enumeration Type min60~4, min
Cell Selection and min60(60),
min120~5,
Re-selection min120(120),
min180~6
min180(180)
ms50(50),
Mobility ms50~0, ms100~1,
ms100(100),
Management ms150~2,
ms150(150),
Cell Selection and ms200~3,
Enumeration Type ms200(200), ms
Re-selection ms500~4,
ms500(500),
RRC Connection ms1000~5,
ms1000(1000),
Management ms2000~6
ms2000(2000)
ms100(100), ms100~0,
ms200(200), ms200~1,
Mobility
ms500(500), ms500~2,
Management
Enumeration Type ms1000(1000), ms1000~3, ms
Cell Selection and
ms2000(2000), ms2000~4,
Re-selection
ms4000(4000), ms4000~5,
ms8000(8000) ms8000~6
min5(5), min10(10),
min5~0, min10~1,
Mobility min20(20),
min20~2, min30~3,
Management min30(30),
Enumeration Type min60~4, min
Cell Selection and min60(60),
min120~5,
Re-selection min120(120),
min180~6
min180(180)
RRC Connection
Management
RRC Connection
Management
IPv4(IPv4 Address),
None Enumeration Type IPv4~0, IPv6~1 None
IPv6(IPv6 Address)


arameter0_bit10), ~6,
RsvdSwPara0_bit1 RsvdSwPara0_bit8
1(ReservedSwitchP ~7,
arameter0_bit11), RsvdSwPara0_bit9
RsvdSwPara0_bit1 ~8,
2(ReservedSwitchP RsvdSwPara0_bit1
arameter0_bit12), 0~9,
3(ReservedSwitchP 1~10,
RsvdSwPara0_bit1 2~11,
None Bit Field Type None











































Dynamic Downlink
Power Allocation
DB_6_P_A(-6 dB),
DB_4DOT77_P_A(- DB_6_P_A~0,
4.77 dB), DB_4DOT77_P_A~
DB_3_P_A(-3 dB), 1, DB_3_P_A~2,
Dynamic Downlink DB_1DOT77_P_A(- DB_1DOT77_P_A~
Enumeration Type dB
Power Allocation 1.77 dB), 3, DB0_P_A~4,
DB0_P_A(0 dB), DB1_P_A~5,
DB1_P_A(1 dB), DB2_P_A~6,
DB2_P_A(2 dB), DB3_P_A~7
DB3_P_A(3 dB)
DRX Interval Type 0~999 N/A per mill



DRX Interval Type 2~300 N/A 20ms
UU_DISABLE(Disa
Uplink Power ble), UU_DISABLE~0,
Control UU_ENABLE(Enabl UU_ENABLE~1
e)
-105,-90,-75,-60,-
Uplink Power 45,-30,-
Interval Type N/A 0.1dB
Control 15,0,15,30,45,60,75
,90,105,120
-30,-20,-
Uplink Power 10,0,10,20,30,40,50
Interval Type N/A 0.1dB
Control ,60,70,80,90,100,11
0,120
COEFF(UU_FC1_F
ILTER_COEFF),
UU_FC2_FILTER_
COEFF(UU_FC2_F
UU_FC0_FILTER_
ILTER_COEFF),
COEFF~0,
UU_FC3_FILTER_
UU_FC1_FILTER_
COEFF(UU_FC3_F
COEFF~1,
ILTER_COEFF),
UU_FC2_FILTER_
UU_FC4_FILTER_
COEFF~2,
COEFF(UU_FC4_F
UU_FC3_FILTER_
ILTER_COEFF),
COEFF~3,
UU_FC5_FILTER_
UU_FC4_FILTER_
COEFF(UU_FC5_F
COEFF~4,
ILTER_COEFF),
UU_FC5_FILTER_
UU_FC6_FILTER_
COEFF~5,
COEFF(UU_FC6_F
UU_FC6_FILTER_
ILTER_COEFF),
COEFF~6,
UU_FC7_FILTER_
Uplink Power UU_FC7_FILTER_
Enumeration Type COEFF(UU_FC7_F None
Control COEFF~7,
ILTER_COEFF),
UU_FC8_FILTER_
UU_FC8_FILTER_
COEFF~8,
COEFF(UU_FC8_F
UU_FC9_FILTER_
ILTER_COEFF),
COEFF~9,
UU_FC9_FILTER_
UU_FC11_FILTER_
COEFF(UU_FC9_F
COEFF~10,
ILTER_COEFF),
UU_FC13_FILTER_
UU_FC11_FILTER_
COEFF~11,
COEFF(UU_FC11_
UU_FC15_FILTER_
FILTER_COEFF),
COEFF~12,
UU_FC13_FILTER_
UU_FC17_FILTER_
COEFF(UU_FC13_
COEFF~13,
FILTER_COEFF),
UU_FC19_FILTER_
UU_FC15_FILTER_
COEFF~14
COEFF(UU_FC15_
FILTER_COEFF),
UU_FC17_FILTER_
COEFF(UU_FC17_
Distance based
Inter-RAT handover
to UTRAN
Distance based EUTRAN~0,
EUTRAN, GERAN,
Inter-RAT handover Bit Field Type GERAN~1, None
UTRAN
to GERAN UTRAN~2
Distance Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
Distance based
Inter-RAT handover Interval Type 1~1000 N/A 100m
to UTRAN
Distance based
Inter-RAT handover
to GERAN

DRX Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
PSF1(1 subframe),
PSF2(2 subframes),
PSF3(3 subframes),
PSF4(4 subframes),
PSF5(5 subframes),
PSF6(6 subframes),
PSF8(8 subframes),
PSF1~0, PSF2~1,
PSF10(10
PSF3~2, PSF4~3,
subframes),
PSF5~4, PSF6~5,
PSF20(20
PSF8~6, PSF10~7,
subframes),
PSF20~8,
PSF30(30
PSF30~9,
DRX Enumeration Type subframes), subframe
PSF40~10,
PSF40(40
PSF50~11,
subframes),
PSF60~12,
PSF50(50
PSF80~13,
subframes),
PSF100~14,
PSF60(60
PSF200~15
subframes),
PSF80(80
subframes),
PSF100(100
subframes),
PSF200(200
subframes)
PSF1(1 subframe),
PSF2(2 subframes),
PSF3(3 subframes),
PSF4(4 subframes),
PSF5(5 subframes),
PSF6(6 subframes),
PSF8(8 subframes),
PSF10(10
subframes),
PSF20(20
PSF1~0, PSF2~1,
subframes),
PSF3~2, PSF4~3,
PSF30(30
PSF5~4, PSF6~5,
subframes),
PSF8~6, PSF10~7,
PSF40(40
PSF20~8,
subframes),
PSF30~9,
PSF50(50
PSF40~10,
subframes),
PSF50~11,
PSF60(60
PSF60~12,
PSF80~13,
PSF80(80
PSF100~14,
subframes),
PSF200~15,
PSF100(100
PSF300~16,
subframes),
PSF500~17,
PSF200(200
PSF750~18,
subframes),
PSF1280~19,
PSF300(300
PSF1920~20,
subframes),
PSF2560~21
PSF500(500
subframes),
PSF750(750
subframes),
PSF1280(1280
subframes),
PSF1920(1920
subframes),
PSF2560(2560
subframes)
sf1(1 subframe),
sf2(2 subframes),
sf4(4 subframes), sf1~0, sf2~1, sf4~2,
DRX
sf6(6 subframes), sf6~3, sf8~4,
DL Asynchronous Enumeration Type subframe
sf8(8 subframes), sf16~5, sf24~6,
HARQ
sf16(16 subframes), sf33~7
sf24(24 subframes),
sf33(33 subframes)
SF10(10
subframes),
SF20(20
subframes),
SF32(32
subframes),
SF40(40
subframes),
SF64(64
subframes),
SF10~0, SF20~1,
SF80(80
SF32~2, SF40~3,
subframes),
SF64~4, SF80~5,
SF128(128
SF128~6,
subframes),
SF160~7,
SF160(160
SF256~8,
subframes),
DRX Enumeration Type SF320~9, subframe
SF256(256
SF512~10,
subframes),
SF640~11,
SF320(320
SF1024~12,
subframes),
SF1280~13,
SF512(512
SF2048~14,
subframes),
SF2560~15
SF640(640
subframes),
SF1024(1024
subframes),
SF1280(1280
subframes),
SF2048(2048
subframes),
SF2560(2560
subframes)
UU_DISABLE(Disa
ble), UU_DISABLE~0,
DRX Enumeration Type None
UU_ENABLE(Enabl UU_ENABLE~1
e)
SF2(2 subframes),
SF5(5 subframes),
SF8(8 subframes),
SF10(10
subframes),
SF16(16
subframes),
SF20(20
subframes),
SF32(32 SF2~0, SF5~1,
subframes), SF8~2, SF10~3,
SF40(40 SF16~4, SF20~5,
SF64(64 SF64~8, SF80~9,
DRX Enumeration Type subframes), SF128~10, subframe
SF80(80 SF160~11,
subframes), SF256~12,
SF128(128 SF320~13,
SF160(160 SF640~15
subframes),
SF256(256
subframes),
SF320(320
subframes),
SF512(512
subframes),
SF640(640
subframes)
DRX Interval Type 1~16 N/A None

PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
0ms~0, 40ms~1,
PS Inter-RAT 64ms~2, 80ms~3,
Mobility between E- 100ms~4,
UTRAN and 0ms, 40ms, 64ms, 128ms~5,
UTRAN 80ms, 100ms, 160ms~6,
PS Inter-RAT 128ms, 160ms, 256ms~7,
Mobility between E- 256ms, 320ms, 320ms~8,
Enumeration Type ms
UTRAN and 480ms, 512ms, 480ms~9,
GERAN 640ms, 1024ms, 512ms~10,
Mobility between E- 5120ms 1024ms~12,
UTRAN and 1280ms~13,
CDMA2000 2560ms~14,
5120ms~15
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
Interval Type -141~-43 N/A dBm
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
Interval Type -40~-6 N/A 0.5dB
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Interval Type 0~15 N/A dB
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
3GPP R8
Specifications
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
Interval Type -63~0 N/A 0.5dB
UTRAN and
CDMA2000
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
CDMA2000 640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
RRC Connection
Management
RRC Connection
Management
MS100_T301(100m
s),
MS200_T301(200m
s),
MS300_T301(300m MS100_T301~0,
s), MS200_T301~1,
MS400_T301(400m MS300_T301~2,
RRC Connection s), MS400_T301~3,
Enumeration Type ms
Management MS600_T301(600m MS600_T301~4,
s), MS1000_T301~5,
MS1000_T301(100 MS1500_T301~6,
0ms), MS2000_T301~7
MS1500_T301(150
0ms),
MS2000_T301(200
0ms)
MS0_T310(0ms),
MS50_T310(50ms),
MS100_T310(100m
MS0_T310~0,
s),
MS50_T310~1,
MS200_T310(200m
MS100_T310~2,
RRC Connection s),
Enumeration Type MS200_T310~3, ms
Management MS500_T310(500m
MS500_T310~4,
s),
MS1000_T310~5,
MS1000_T310(100
MS2000_T310~6
0ms),
MS2000_T310(200
0ms)
MS1000_T311(100
0ms),
MS3000_T311(300
0ms),
MS1000_T311~0,
MS5000_T311(500
MS3000_T311~1,
0ms),
MS5000_T311~2,
RRC Connection MS10000_T311(10
Management 000ms),
MS15000_T311~4,
MS15000_T311(15
MS20000_T311~5,
000ms),
MS30000_T311~6
MS20000_T311(20
000ms),
MS30000_T311(30
000ms)
n1(1), n2(2), n3(3), n1~0, n2~1, n3~2,

RRC Connection
Enumeration Type n4(4), n6(6), n8(8), n4~3, n6~4, n8~5, None
Management
n10(10), n20(20) n10~6, n20~7
n1(1), n2(2), n3(3), n1~0, n2~1, n3~2,

RRC Connection
Management
n8(8), n10(10) n8~6, n10~7
Enhanced
Scheduling
Dynamic
Scheduling
3GPP R8
Specifications
Coverage Based
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Coverage Based
Intra-frequency Interval Type 0~9 N/A None
Handover

RRC Connection NOT_CFG(NOT_C NOT_CFG~0,
Management FG), CFG(CFG) CFG~1
RRC Connection
Management
3GPP R8
Specifications
QCI1(QCI 1),
QCI2(QCI 2),
Enhanced
Scheduling
Enumeration Type QCI5(QCI 5), QCI5~5, QCI6~6, None
Dynamic
Scheduling
QCI7(QCI 7), QCI9~9
QCI8(QCI 8),
QCI9(QCI 9)
Coverage Based
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Coverage Based
Handover

Basic Scheduling ms5(SRI 5ms),
Enhanced ms10(SRI 10ms), ms5~0, ms10~1,
Scheduling Enumeration Type ms20(SRI 20ms), ms20~2, ms40~3, None
Physical Channel ms40(SRI 40ms), ms80~4
Management ms80(SRI 80ms)
RRC Connection NOT_CFG(NOT_C NOT_CFG~0,

Management FG), CFG(CFG) CFG~1
RRC Connection
Management
3GPP R8
Specifications
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
Enumeration Type ms
CDMA2000 640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Intra-LTE Load
Balancing
3GPP R8
Specifications
PS Inter-RAT
Mobility between E-
UTRAN and Interval Type 0~9 N/A None
GERAN
SRVCC to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
SRVCC to GERAN
RAT handover to
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and Interval Type -110~-48 N/A dBm
GERAN
SRVCC to GERAN
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
PS Inter-RAT 0ms, 40ms, 64ms, 128ms~5,
GERAN 256ms, 320ms, 320ms~8,
Enumeration Type ms
SRVCC to GERAN 480ms, 512ms, 480ms~9,
Service based inter- 640ms, 1024ms, 512ms~10,
RAT handover to 1280ms, 2560ms, 640ms~11,
GERAN 5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Intra-LTE Load Interval Type -110~-48 N/A dBm
Balancing
RAT handover to
GERAN
3GPP R8
Specifications
PS Inter-RAT
Mobility between E-
UTRAN and Interval Type 0~9 N/A None
UTRAN
SRVCC to UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and Interval Type -48~0 N/A 0.5dB
UTRAN
SRVCC to UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and Interval Type -120~-25 N/A dBm
UTRAN
SRVCC to UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
SRVCC to UTRAN
RAT handover to
UTRAN
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
PS Inter-RAT 0ms, 40ms, 64ms, 128ms~5,
UTRAN 256ms, 320ms, 320ms~8,
Enumeration Type ms
SRVCC to UTRAN 480ms, 512ms, 480ms~9,
Service based inter- 640ms, 1024ms, 512ms~10,
RAT handover to 1280ms, 2560ms, 640ms~11,
UTRAN 5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Intra-LTE Load Interval Type -48~0 N/A 0.5dB
Balancing
RAT handover to
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Intra-LTE Load Interval Type -120~-25 N/A dBm
Balancing
RAT handover to
UTRAN
3GPP R8
Specifications
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Coverage Based
Inter-frequency Interval Type 0~30 N/A 0.5dB
Handover
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
128ms, 160ms, 256ms~7,
Coverage Based
256ms, 320ms, 320ms~8,
Inter-frequency Enumeration Type ms
480ms, 512ms, 480ms~9,
Handover
640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
Coverage Based
Inter-frequency Interval Type -141~-43 N/A dBm
Handover
Coverage Based
Inter-frequency Interval Type -40~-6 N/A 0.5dB
Handover
Coverage Based
Handover
Coverage Based
Inter-frequency Interval Type -40~-6 N/A 0.5dB
Handover
Coverage Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover Interval Type 0~30 N/A 0.5dB
Intra-LTE Load
Balancing
Service Based
Inter-frequency
Handover
Coverage Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
Coverage Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
0ms~0, 40ms~1,
64ms~2, 80ms~3,
Coverage Based
100ms~4,
Inter-frequency
0ms, 40ms, 64ms, 128ms~5,
Handover
80ms, 100ms, 160ms~6,
Distance Based
128ms, 160ms, 256ms~7,
Inter-frequency
256ms, 320ms, 320ms~8,
Handover Enumeration Type ms
480ms, 512ms, 480ms~9,
Intra-LTE Load
640ms, 1024ms, 512ms~10,
Balancing
1280ms, 2560ms, 640ms~11,
Service Based
5120ms 1024ms~12,
Inter-frequency
1280ms~13,
Handover
2560ms~14,
5120ms~15
Intra-LTE Load
Balancing
Service Based Interval Type -141~-43 N/A dBm
Inter-frequency
Handover
Intra-LTE Load
Balancing
Service Based Interval Type -40~-6 N/A 0.5dB
Inter-frequency
Handover
None Interval Type -141~-43 N/A dBm
None Interval Type -40~-6 N/A 0.5dB

Coverage Based
Inter-frequency Interval Type -30~30 N/A 0.5dB
Handover
Coverage Based
Handover
Coverage Based
Handover
None Interval Type -140~-43 N/A dBm
None Interval Type -40~-6 N/A 0.5dB
3GPP R8
Specifications
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover Interval Type 0~30 N/A 0.5dB
Intra-LTE Load
Balancing
Coverage Based
Intra-frequency Interval Type -30~30 N/A 0.5dB
Handover
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
128ms, 160ms, 256ms~7,
Coverage Based
256ms, 320ms, 320ms~8,
Intra-frequency Enumeration Type ms
480ms, 512ms, 480ms~9,
Handover
640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
RAN Sharing with
Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier Character String
RAN Sharing with Type
Dedicated Carrier
CNOPERATOR_PR
RAN Sharing with IMARY(Primary CNOPERATOR_PR
Common Carrier Operator), IMARY~0,
RAN Sharing with CNOPERATOR_SE CNOPERATOR_SE
Dedicated Carrier CONDARY(Second CONDARY~1
ary Operator)
RAN Sharing with

Dedicated Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with
Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
Emergency Call Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Emergency Call Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Emergency Call Interval Type 1~15 N/A None

Emergency Call Interval Type 1~15 N/A None
INDEPENDENT(Ind
ependent Operator
Mode),
RAN Sharing with SHARED_FREQ(S INDEPENDENT~0,
Common Carrier hared Frequency SHARED_FREQ~1,
RAN Sharing with Sharing Mode), SEPARATED_FRE
Dedicated Carrier SEPARATED_FRE Q~2
Q(Separate
Frequency Sharing
Mode)
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier

S1-flex Interval Type 0~15 N/A None
S1-flex Interval Type 0~79 N/A None
S1-flex
RAN Sharing with
Common Carrier Interval Type 0~5 N/A None
RAN Sharing with
Dedicated Carrier
Release_R8(Releas
e 8),
Release_R8~0,
3GPP R8 Release_R9(Releas
Enumeration Type Release_R9~1, None
Specifications e 9),
Release_R10~2
Release_R10(Rele
ase 10)
FALSE(FALSE),
None Enumeration Type FALSE~0, TRUE~1 None
TRUE(TRUE)
Normal(Normal),
Normal~0,
None Enumeration Type Abnormal(Abnormal None
Abnormal~1
)
Normal(Normal), Normal~0,
None Enumeration Type Abnormal(Abnormal Abnormal~1, None
), Blocked(Blocked) Blocked~2
FALSE(FALSE),
FALSE~0, TRUE~1,
S1-flex Enumeration Type TRUE(TRUE), None
NULL~2
NULL(NULL)
Character String
Type
S1-flex
RAN Sharing with
Character String
Common Carrier 0~224 characters N/A None
Type
RAN Sharing with
Dedicated Carrier
Character String
Type
Null(Null),
LowerLinkFault(Low
er Layer Link Fault),
MmecImpact(Mmec
Impact),
SetupFail(Setup
Failure),
CfgErr(Configuratio Null~0,
n Error), LowerLinkFault~1,
LicRestrict(License MmecImpact~2,
Restriction), SetupFail~3,
None Enumeration Type PlmnDiff(The PLMN CfgErr~4, None
of the operator LicRestrict~5,
owning the S1 PlmnDiff~6,
interface is not TacNotCfg~7,
supported by the Undefine~255
MME),
TacNotCfg(The TAC
for the operator
owning the S1
interface is not
configured),
Undefine(Undefine)

DISABLE(disable), DISABLE~0,
ENABLE(enable) ENABLE~1
Self-configuration
Automatic Character String
Neighbour Relation Type
(ANR)
Self-configuration
Automatic Character String
Neighbour Relation Type
(ANR)
Self-configuration
Automatic
Neighbour Relation
(ANR)
X2_BLACK_LIST_T
Self-configuration YPE(X2 Black List X2_BLACK_LIST_T
Automatic Type), YPE~0,
Neighbour Relation X2_WHITE_LIST_T X2_WHITE_LIST_T
(ANR) YPE(X2 White List YPE~1
Type)
Mobility
Management
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
Release_R8(Releas
e 8),
Release_R8~0,
3GPP R8 Release_R9(Releas
Enumeration Type Release_R9~1, None
Specifications e 9),
Release_R10~2
Release_R10(Rele
ase 10)
FORBID_AUTO_R
MV(Forbid Auto FORBID_AUTO_R
Remove), MV~0,
PERMIT_AUTO_R PERMIT_AUTO_R
MV(Permit Auto MV~1
Remove)
Character String
Type
Character String
Type
Normal(Normal),
Normal~0,
None Enumeration Type Abnormal(Abnormal None
Abnormal~1
)
SCTP_LINK_FAUL
T(SCTP Link
Failure),
SETUP_FAILURE_ SCTP_LINK_FAUL
OCCUR(Setup T~0,
Failure), SETUP_FAILURE_
PEERIN_BLACK_L OCCUR~1,
IST(Peer eNodeB PEERIN_BLACK_L
None Enumeration Type Blacklisted), IST~2, None
STATE_NORMAL(N STATE_NORMAL~
ULL), 3,
SETUP_ONLY_ON SETUP_ONLY_ON
E_LINK_ALLOWED E_LINK_ALLOWED
(Only one interface ~4
allowed to be setup
between two logical
eNodeBs)

SF10(10
subframes),
SF20(20
subframes),
SF32(32
subframes),
SF40(40
subframes),
SF64(64
subframes),
SF10~0, SF20~1,
SF80(80
SF32~2, SF40~3,
subframes),
SF64~4, SF80~5,
SF128(128
SF128~6,
subframes),
SF160~7,
SF160(160
SF256~8,
subframes),
DRX Enumeration Type SF320~9, subframe
SF256(256
SF512~10,
subframes),
SF640~11,
SF320(320
SF1024~12,
subframes),
SF1280~13,
SF512(512
SF2048~14,
subframes),
SF2560~15
SF640(640
subframes),
SF1024(1024
subframes),
SF1280(1280
subframes),
SF2048(2048
subframes),
SF2560(2560
subframes)
PSF1(1 subframe),
PSF2(2 subframes),
PSF3(3 subframes),
PSF4(4 subframes),
PSF5(5 subframes),
PSF6(6 subframes),
PSF8(8 subframes),
PSF1~0, PSF2~1,
PSF10(10
PSF3~2, PSF4~3,
subframes),
PSF5~4, PSF6~5,
PSF20(20
PSF8~6, PSF10~7,
subframes),
PSF20~8,
PSF30(30
PSF30~9,
PSF40~10,
PSF40(40
PSF50~11,
subframes),
PSF60~12,
PSF50(50
PSF80~13,
subframes),
PSF100~14,
PSF60(60
PSF200~15
subframes),
PSF80(80
subframes),
PSF100(100
subframes),
PSF200(200
subframes)
PSF1(1 subframe),
PSF2(2 subframes),
PSF3(3 subframes),
PSF4(4 subframes),
PSF5(5 subframes),
PSF6(6 subframes),
PSF8(8 subframes),
PSF10(10
subframes),
PSF20(20
PSF1~0, PSF2~1,
subframes),
PSF3~2, PSF4~3,
PSF30(30
PSF5~4, PSF6~5,
subframes),
PSF8~6, PSF10~7,
PSF40(40
PSF20~8,
subframes),
PSF30~9,
PSF50(50
PSF40~10,
subframes),
PSF50~11,
PSF60(60
PSF60~12,
PSF80~13,
PSF80(80
PSF100~14,
subframes),
PSF200~15,
PSF100(100
PSF300~16,
subframes),
PSF500~17,
PSF200(200
PSF750~18,
subframes),
PSF1280~19,
PSF300(300
PSF1920~20,
subframes),
PSF2560~21
PSF500(500
subframes),
PSF750(750
subframes),
PSF1280(1280
subframes),
PSF1920(1920
subframes),
PSF2560(2560
subframes)
UU_DISABLE(Disa
ble), UU_DISABLE~0,
DRX Enumeration Type None
UU_ENABLE(Enabl UU_ENABLE~1
e)
SF2(2 subframes),
SF5(5 subframes),
SF8(8 subframes),
SF10(10
subframes),
SF16(16
subframes),
SF20(20
subframes),
SF32(32 SF2~0, SF5~1,
SF40(40 SF16~4, SF20~5,
SF64(64 SF64~8, SF80~9,
DRX Enumeration Type subframes), SF128~10, subframe
SF80(80 SF160~11,
SF128(128 SF320~13,
SF160(160 SF640~15
subframes),
SF256(256
subframes),
SF320(320
subframes),
SF512(512
subframes),
SF640(640
subframes)

SF128(128
subframes),
SF160(160
subframes),
SF256(256
SF320(320 SF160~7,
SF512(512 SF320~9,
DRX Enumeration Type subframe
SF640(640 SF640~11,
SF1024(1024 SF1280~13,
SF1280(1280 SF2560~15
subframes),
SF2048(2048
subframes),
SF2560(2560
subframes)
SF128(128
subframes),
SF160(160
subframes),
SF256(256
SF320(320 SF160~7,
SF512(512 SF320~9,
DRX Enumeration Type subframe
SF640(640 SF640~11,
SF1024(1024 SF1280~13,
SF1280(1280 SF2560~15
subframes),
SF2048(2048
subframes),
SF2560(2560
subframes)
Enhanced
Scheduling
Dynamic
Scheduling
IMSSignalling(IMS
Signalling),
Enhanced IMSSignalling~5,
LowDelay(Low
Scheduling LowDelay~7,
Enumeration Type Delay), None
Dynamic TCPorBuffStreamin
TCPorBuffStreamin
Scheduling g~9
g(TCP Based or
Buffered Streaming)
Enhanced
Scheduling
Dynamic
Scheduling Interval Type 1~1000 N/A 0.001
Enhanced
Transmission QoS
Management
Enhanced
Scheduling
Dynamic
Scheduling
MinGbrRate_0_KB( MinGbrRate_0_KB
0KB/s), ~0,
1KB/s), ~8000,
2KB/s), ~16000,
MinGbrRate_4KB(4 MinGbrRate_4KB~
KB/s), 32000,
8KB/s), ~64000,
Basic Scheduling
MinGbrRate_16_K MinGbrRate_16_K
Enhanced Enumeration Type KB/s
B(16KB/s), B~128000,
Scheduling
B(32KB/s), B~256000,
B(64KB/s), B~512000,
B(128KB/s), B~1024000,
B(256KB/s), B~2048000,
B(512KB/s) B~4096000
0KB/s), ~0,
1KB/s), ~8000,
2KB/s), ~16000,
MinGbrRate_4KB(4 MinGbrRate_4KB~
KB/s), 32000,
8KB/s), ~64000,
Basic Scheduling
B(16KB/s), B~128000,
Scheduling
B(32KB/s), B~256000,
B(64KB/s), B~512000,
B(128KB/s), B~1024000,
B(256KB/s), B~2048000,
B(512KB/s) B~4096000
Basic Scheduling
Enhanced Interval Type 0~10 N/A 0.1
Scheduling
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
SRVCC to UTRAN
SRVCC to GERAN
RAT handover to
UTRAN
Inter-RAT Load
Sharing to GERAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
GERAN
CS Fallback to
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
PBR_0_KBps(0KB/
s),
PBR_8_KBps(8KB/
s),
PBR_16_KBps(16K PBR_0_KBps~0,
B/s), PBR_8_KBps~1,
Basic Scheduling
B/s), PBR_32_KBps~3,
Scheduling
PBR_128_KBps(12 PBR_256_KBps~6,
8KB/s), PBR_INFINITY~7
PBR_256_KBps(25
6KB/s),
PBR_INFINITY(Infi
nity)
Basic Scheduling
Enhanced Interval Type 9~16 N/A None
Scheduling
Radio Bearer
Management
PAID_USER(Paid
Basic Scheduling
User), PAID_USER~0,
FREE_USER(Free FREE_USER~1
Scheduling
User)
Transport
Overbooking
Transport
Differentiated Flow
Control
Transport Resource
Overload Control
FLOW_CTRL(Flow
Transport Dynamic FLOW_CTRL~0,
Control),
Flow Control Enumeration Type NON_FLOW_CTRL None
NON_FLOW_CTRL
Different Transport ~1
(Non Flow Control)
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Enhanced
Transmission QoS
Management
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
SRVCC to UTRAN
SRVCC to GERAN
Intra-LTE Load
Balancing
RAT handover to
UTRAN
Inter-RAT Load
Sharing to GERAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
GERAN
CS Fallback to
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
SRVCC to UTRAN
PS Inter-RAT PS_HO~0,
PS_HO, SRVCC,
Mobility between E- Bit Field Type SRVCC~1, None
REDIRECTION
UTRAN and REDIRECTION~2
UTRAN
SRVCC to GERAN Bit Field Type SRVCC SRVCC~0 None

PS_HO~0,
PS Inter-RAT PS_HO,
NACC_HO~1,
Mobility between E- NACC_HO,
Bit Field Type CCO_HO~2, None
UTRAN and CCO_HO, SRVCC,
SRVCC~3,
GERAN REDIRECTION
REDIRECTION~4
PS Inter-RAT
Mobility between E- SRVCC(CDMA1XR
Bit Field Type SRVCC~0 None
UTRAN and TTHoSwitch)
CDMA2000
PS Inter-RAT
Mobility between E- OPT_HO, OPT_HO~0,
Bit Field Type None
UTRAN and NON_OPT_HO NON_OPT_HO~1
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
SRVCC to UTRAN
SRVCC to GERAN
Intra-LTE Load PERMIT_HO_ENU PERMIT_HO_ENU
Balancing M(Permit Ho), M~0,
Service based inter- FORBID_HO_ENU FORBID_HO_ENU
RAT handover to M(Forbid Ho) M~1
UTRAN
Inter-RAT Load
Sharing to GERAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
GERAN
CS Fallback to
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
PERMIT_FAST_AN
Automatic PERMIT_FAST_AN
R_MEAS_ENUM~0
Neighbour Relation R_MEAS_ENUM,
Enumeration Type , None
(ANR) FORBID_FAST_AN
FORBID_FAST_AN
Inter-RAT ANR R_MEAS_ENUM
R_MEAS_ENUM~1

Radio Bearer
Management
DiscardTimer_50(5 DiscardTimer_50~0
0 ms), ,
DiscardTimer_100( DiscardTimer_100~
100 ms), 1,
150 ms), 2,
Radio Bearer 300 ms), 3,
Enumeration Type ms
Management DiscardTimer_500( DiscardTimer_500~
500 ms), 4,
750 ms), 5,
DiscardTimer_1500 DiscardTimer_1500
(1500 ms), ~6,
DiscardTimer_Infinit DiscardTimer_Infinit
y(infinity) y~7
RlcMode_AM(Ackn
owledge Mode),
Radio Bearer RlcMode_AM~1,
Enumeration Type RlcMode_UM(Un- None
Management RlcMode_UM~2
acknowledge
Mode)
Maxretx_Threshold Maxretx_Threshold
_t1(1), _t1~0,
_t2(2), _t2~1,
_t3(3), _t3~2,
Radio Bearer _t4(4), _t4~3,
Management Maxretx_Threshold Maxretx_Threshold
_t6(6), _t6~4,
_t8(8), _t8~5,
_t16(16), _t16~6,
_t32(32) _t32~7
_t1(1), _t1~0,
_t2(2), _t2~1,
_t3(3), _t3~2,
Radio Bearer _t4(4), _t4~3,
Management Maxretx_Threshold Maxretx_Threshold
_t6(6), _t6~4,
_t8(8), _t8~5,
_t16(16), _t16~6,
_t32(32) _t32~7
PollByte_kb25(25
kBytes),
PollByte_kb50(50
kBytes),
PollByte_kb75(75
kBytes),
PollByte_kb25~0,
PollByte_kb100(10
PollByte_kb50~1,
0 kBytes),
PollByte_kb75~2,
PollByte_kb125(12
PollByte_kb100~3,
5 kBytes),
PollByte_kb125~4,
PollByte_kb250(25
PollByte_kb250~5,
0 kBytes),
PollByte_kb375~6,
PollByte_kb375(37
PollByte_kb500~7,
5 kBytes),
PollByte_kb750~8,
Radio Bearer PollByte_kb500(50
Enumeration Type PollByte_kb1000~9, byte
Management 0 kBytes),
PollByte_kb1250~1
PollByte_kb750(75
0,
0 kBytes),
PollByte_kb1500~1
PollByte_kb1000(1
1,
000 kBytes),
PollByte_kb2000~1
PollByte_kb1250(1
2,
250 kBytes),
PollByte_kb3000~1
PollByte_kb1500(1
3,
500 kBytes),
PollByte_infinity~14
PollByte_kb2000(2
000 kBytes),
PollByte_kb3000(3
000 kBytes),
PollByte_infinity(infi
nite kBytes)
PollByte_kb25(25
kBytes),
PollByte_kb50(50
kBytes),
PollByte_kb75(75
kBytes),
PollByte_kb25~0,
PollByte_kb100(10
PollByte_kb50~1,
0 kBytes),
PollByte_kb75~2,
PollByte_kb125(12
PollByte_kb100~3,
5 kBytes),
PollByte_kb125~4,
PollByte_kb250(25
PollByte_kb250~5,
0 kBytes),
PollByte_kb375~6,
PollByte_kb375(37
PollByte_kb500~7,
5 kBytes),
PollByte_kb750~8,
Radio Bearer PollByte_kb500(50
Enumeration Type PollByte_kb1000~9, byte
Management 0 kBytes),
PollByte_kb1250~1
PollByte_kb750(75
0,
0 kBytes),
PollByte_kb1500~1
PollByte_kb1000(1
1,
000 kBytes),
PollByte_kb2000~1
PollByte_kb1250(1
2,
250 kBytes),
PollByte_kb3000~1
PollByte_kb1500(1
3,
500 kBytes),
PollByte_infinity~14
PollByte_kb2000(2
000 kBytes),
PollByte_kb3000(3
000 kBytes),
PollByte_infinity(infi
nite kBytes)
PollPdu_p4(4
PDUs),
PollPdu_p8(8
PDUs),
PollPdu_p16(16 PollPdu_p4~0,
PDUs), PollPdu_p8~1,
Radio Bearer PDUs), PollPdu_p32~3,
Management PollPdu_p64(64 PollPdu_p64~4,
PDUs), PollPdu_Infinity~7
PollPdu_p256(256
PDUs),
PollPdu_Infinity(infi
nite PDUs)
PollPdu_p4(4
PDUs),
PollPdu_p8(8
PDUs),
Radio Bearer PDUs), PollPdu_p32~3,
Management PollPdu_p64(64 PollPdu_p64~4,
PDUs), PollPdu_Infinity~7
PollPdu_p256(256
PDUs),
PollPdu_Infinity(infi
nite PDUs)
Tpollretrans_m95(9
8,
5ms),
Tpollretrans_m100~
Tpollretrans_m100(
19,
100ms),
Tpollretrans_m105~
Tpollretrans_m105(
20,
105ms),
Tpollretrans_m110~
Tpollretrans_m110(
21,
110ms),
Tpollretrans_m115~
Tpollretrans_m115(
22,
115ms),
Tpollretrans_m120~
Tpollretrans_m120(
23,
120ms),
Tpollretrans_m125~
Tpollretrans_m125(
24,
125ms),
Tpollretrans_m130~
Tpollretrans_m130(
25,
130ms),
Tpollretrans_m135~
Tpollretrans_m135(
26,
135ms),
Tpollretrans_m140~
Radio Bearer Tpollretrans_m140(
Enumeration Type 27, ms
Management 140ms),
Tpollretrans_m145~
Tpollretrans_m145(
28,
145ms),
Tpollretrans_m150~
Tpollretrans_m150(
29,
150ms),
Tpollretrans_m155~
Tpollretrans_m155(
30,
155ms),
Tpollretrans_m160~
Tpollretrans_m160(
31,
160ms),
Tpollretrans_m165~
Tpollretrans_m165(
32,
165ms),
Tpollretrans_m170~
Tpollretrans_m170(
33,
170ms),
Tpollretrans_m175~
Tpollretrans_m175(
34,
175ms),
Tpollretrans_m180~
Tpollretrans_m180(
35,
180ms),
Tpollretrans_m185~
Tpollretrans_m185(
36,
185ms),
Tpollretrans_m95(9
8,
5ms),
Tpollretrans_m100~
Tpollretrans_m100(
19,
100ms),
Tpollretrans_m105~
Tpollretrans_m105(
20,
105ms),
Tpollretrans_m110~
Tpollretrans_m110(
21,
110ms),
Tpollretrans_m115~
Tpollretrans_m115(
22,
115ms),
Tpollretrans_m120~
Tpollretrans_m120(
23,
120ms),
Tpollretrans_m125~
Tpollretrans_m125(
24,
125ms),
Tpollretrans_m130~
Tpollretrans_m130(
25,
130ms),
Tpollretrans_m135~
Tpollretrans_m135(
26,
135ms),
Tpollretrans_m140~
Radio Bearer Tpollretrans_m140(
Enumeration Type 27, ms
Management 140ms),
Tpollretrans_m145~
Tpollretrans_m145(
28,
145ms),
Tpollretrans_m150~
Tpollretrans_m150(
29,
150ms),
Tpollretrans_m155~
Tpollretrans_m155(
30,
155ms),
Tpollretrans_m160~
Tpollretrans_m160(
31,
160ms),
Tpollretrans_m165~
Tpollretrans_m165(
32,
165ms),
Tpollretrans_m170~
Tpollretrans_m170(
33,
170ms),
Tpollretrans_m175~
Tpollretrans_m175(
34,
175ms),
Tpollretrans_m180~
Tpollretrans_m180(
35,
180ms),
Tpollretrans_m185~
Tpollretrans_m185(
36,
185ms),
0ms), Tstatprohibit_m95~
Tstatprohibit_m95(9 19,
5ms), Tstatprohibit_m100
Tstatprohibit_m100( ~20,
Tstatprohibit_m110( 22,
Radio Bearer 135ms), Tstatprohibit_m140
Enumeration Type ms
Management Tstatprohibit_m140( ~28,
Tstatprohibit_m95(9 19,
Radio Bearer 135ms), Tstatprohibit_m140
Enumeration Type ms
Management Tstatprohibit_m140( ~28,
Treordering_m30(3 ,
0ms), Treordering_m35~7
Treordering_m35(3 ,
Treordering_m40(4 ,
Treordering_m45(4 ,
Treordering_m50(5 0,
Radio Bearer Treordering_m75(7 5,
Enumeration Type ms
Management 5ms), Treordering_m80~1
5ms), Treordering_m100~
Treordering_m100( 20,
Treordering_m30(3 ,
Treordering_m35(3 ,
Treordering_m40(4 ,
Treordering_m45(4 ,
Enumeration Type ms
PdcpSnsize_7bits(7 PdcpSnsize_7bits~
Radio Bearer bits), 0,
Enumeration Type bit
Management PdcpSnsize_12bits( PdcpSnsize_12bits
12 bits) ~1
RlcSnSize_size5(5b
RlcSnSize_size5~0,
Radio Bearer its),
Enumeration Type RlcSnSize_size10~ bit
Management RlcSnSize_size10(1
1
0bits)
RlcSnSize_size5(5b
RlcSnSize_size5~0,
Radio Bearer its),
Enumeration Type RlcSnSize_size10~ bit
Management RlcSnSize_size10(1
1
0bits)
Treordering_m30(3 ,
Treordering_m35(3 ,
Treordering_m40(4 ,
Treordering_m45(4 ,
Enumeration Type ms
Treordering_m30(3 ,
Treordering_m35(3 ,
Treordering_m40(4 ,
Treordering_m45(4 ,
Enumeration Type ms
Radio Bearer FALSE(FALSE),

Management TRUE(TRUE)
QCI1(QCI 1),
QCI2(QCI 2),
Enhanced
Scheduling
Enumeration Type QCI5(QCI 5), QCI5~5, QCI6~6, None
Dynamic
Scheduling
QCI7(QCI 7), QCI9~9
QCI8(QCI 8),
QCI9(QCI 9)
Enhanced
Scheduling
Dynamic
Enhanced
Transmission QoS
Management
Enhanced
Scheduling
Dynamic
Scheduling
0KB/s), ~0,
1KB/s), ~8000,
2KB/s), ~16000,
Basic Scheduling MinGbrRate_4KB(4 MinGbrRate_4KB~
Enhanced KB/s), 32000,
Scheduling MinGbrRate_8_KB( MinGbrRate_8_KB
Basic Qos 8KB/s), ~64000,
Management MinGbrRate_16_K MinGbrRate_16_K
Enumeration Type KB/s
Dynamic B(16KB/s), B~128000,
Scheduling MinGbrRate_32_K MinGbrRate_32_K
Enhanced B(32KB/s), B~256000,
Transmission QoS MinGbrRate_64_K MinGbrRate_64_K
Management B(64KB/s), B~512000,
B(128KB/s), B~1024000,
B(256KB/s), B~2048000,
B(512KB/s) B~4096000
0KB/s), ~0,
1KB/s), ~8000,
2KB/s), ~16000,
Basic Scheduling MinGbrRate_4KB(4 MinGbrRate_4KB~
Enhanced KB/s), 32000,
Scheduling MinGbrRate_8_KB( MinGbrRate_8_KB
Basic Qos 8KB/s), ~64000,
Management MinGbrRate_16_K MinGbrRate_16_K
Enumeration Type KB/s
Dynamic B(16KB/s), B~128000,
Scheduling MinGbrRate_32_K MinGbrRate_32_K
Enhanced B(32KB/s), B~256000,
Transmission QoS MinGbrRate_64_K MinGbrRate_64_K
Management B(64KB/s), B~512000,
B(128KB/s), B~1024000,
B(256KB/s), B~2048000,
B(512KB/s) B~4096000
Basic Scheduling
Enhanced
Dynamic
Scheduling
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
SRVCC to UTRAN
SRVCC to GERAN
RAT handover to
UTRAN
Inter-RAT Load
Sharing to GERAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
GERAN
CS Fallback to
UTRAN
CS Fallback to
GERAN
CS Fallback to
CDMA2000 1xRTT
Basic Scheduling
Scheduling
PBR_0_KBps(0KB/
s),
PBR_8_KBps(8KB/
s),
B/s), PBR_8_KBps~1,
Basic Scheduling
Enhanced
Scheduling Enumeration Type KB/s
Dynamic
Scheduling
PBR_128_KBps(12 PBR_256_KBps~6,
8KB/s), PBR_INFINITY~7
PBR_256_KBps(25
6KB/s),
PBR_INFINITY(Infi
nity)
Basic Scheduling
Scheduling
Transport
Overbooking
Transport
Differentiated Flow
Control
Transport Resource FLOW_CTRL(Flow
FLOW_CTRL~0,
Overload Control Control),
Enumeration Type NON_FLOW_CTRL None
Transport Dynamic NON_FLOW_CTRL
~1
Flow Control (Non Flow Control)
Different Transport
Paths based on
QoS Grade
Intra-LTE Load
Balancing
CLASS_0(CLASS_
0),
CLASS_0~0,
Dynamic CLASS_1(CLASS_
Enumeration Type CLASS_1~1, None
Scheduling 1),
CLASS_2~2
CLASS_2(CLASS_
2)
NO_ADAPTIVE(NO
DL 2x2 MIMO
_ADAPTIVE),
DL 4x2 MIMO NO_ADAPTIVE~0,
TxD_BF_ADAPTIV
BEAMFORMING TxD_BF_ADAPTIV
E(TxD_BF_ADAPTI
AND MIMO Enumeration Type E~1, None
VE),
ADAPTIVE MIMO_BF_ADAPTI
MIMO_BF_ADAPTI
SWITCH (Test VE~2
VE(MIMO_BF_ADA
Feature)
PTIVE)
DL 2x2 MIMO
DL 4x2 MIMO TM2(TM2),
BEAMFORMING TM3(TM3), TM2~0, TM3~1,
AND MIMO Enumeration Type TM7(TM7), TM7~2, TM8~3, None
ADAPTIVE TM8(TM8), TM4~4
SWITCH (Test TM4(TM4)
Feature)
Basic Scheduling Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None

ms2(2ms),
ms2~2, ms5~5,
ms5(5ms),
ms10~10,
ms10(10ms),
ms20~20,
ms20(20ms),
ms32~32,
ms32(32ms),
Basic Scheduling Enumeration Type ms40~40, ms
ms40(40ms),
ms64~64,
ms64(64ms),
ms80~80,
ms80(80ms),
ms128~128,
ms128(128ms),
ms160~160
ms160(160ms)
NO_ADAPTIVE(NO
_ADAPTIVE),
OL_ADAPTIVE(OL NO_ADAPTIVE~0,
DL 2x2 MIMO _ADAPTIVE), OL_ADAPTIVE~1,
DL 4x2 MIMO CL_ADAPTIVE(CL_ CL_ADAPTIVE~2,
ADAPTIVE), OC_ADAPTIVE~3
OC_ADAPTIVE(OC
_ADAPTIVE)
TM2(TM2),
DL 2x2 MIMO TM3(TM3), TM2~0, TM3~1,
DL 4x2 MIMO TM4(TM4), TM4~2, TM6~3
TM6(TM6)
Basic Scheduling Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None

ms5(5ms),
ms10(10ms), ms5~1, ms10~2,
Basic Scheduling Enumeration Type ms
ms20(20ms), ms20~3, ms40~4
ms40(40ms)
QCI1(QCI 1),
QCI2(QCI 2),
None Enumeration Type QCI5(QCI 5), QCI5~5, QCI6~6, None
QCI7(QCI 7), QCI9~9
QCI8(QCI 8),
QCI9(QCI 9)
TPeriodBSRTimer_
sf5(5 subframes),
TPeriodBSRTimer_
sf10(10 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf5~0,
sf16(16 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf10~1,
sf20(20 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf16~2,
sf32(32 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf20~3,
sf40(40 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf32~4,
sf64(64 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf40~5,
sf80(80 subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf64~6,
sf128(128
TPeriodBSRTimer_
None Enumeration Type subframes), subframe
sf80~7,
TPeriodBSRTimer_
TPeriodBSRTimer_
sf160(160
sf128~8,
subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf160~9,
sf320(320
TPeriodBSRTimer_
subframes),
sf320~10,
TPeriodBSRTimer_
TPeriodBSRTimer_
sf640(640
sf640~11,
subframes),
TPeriodBSRTimer_
TPeriodBSRTimer_
sf1280~12,
sf1280(1280
TPeriodBSRTimer_
subframes),
sf2560~13,
TPeriodBSRTimer_
TPeriodBSRTimer_i
sf2560(2560
nfinity~14
subframes),
TPeriodBSRTimer_i
nfinity(infinity
subframes)
sf320(sf320),
sf320~0, sf640~1,
sf640(sf640),
sf1280~2,
sf1280(sf1280),
None Enumeration Type sf2560~3, subframe
sf2560(sf2560),
sf5120~4,
sf5120(sf5120),
sf10240~5
sf10240(sf10240)
Coverage Based
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000 GAP_PATTERN_T GAP_PATTERN_T
Intra-LTE Load YPE_1, YPE_1~1,
Balancing GAP_PATTERN_T GAP_PATTERN_T
LOFD-001044 / YPE_2 YPE_2~2
TDLOFD-
001044:Inter-RAT
Load Sharing to
UTRAN LOFD-
001045 / TDLOFD-
001045:Inter-RAT
Load Sharing to
GERAN
Distance based
inter-RAT handover
to UTRAN
Distance based
inter-RAT handover
to GERAN
Service Based
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency FC0~0, FC1~1,
Handover FC2~2, FC3~3,
Distance Based FC0, FC1, FC2, FC4~4, FC5~5,
Inter-frequency FC3, FC4, FC5, FC6~6, FC7~7,
Handover Enumeration Type FC6, FC7, FC8, FC8~8, FC9~9, None
Intra-LTE Load FC9, FC11, FC13, FC11~10,
Balancing FC15, FC17, FC19 FC13~11,
LBFD-00201805 / FC15~12,
TDLBFD- FC17~13, FC19~14
00201805:Service
Based Inter-
frequency
Handover
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency FC0~0, FC1~1,
Handover FC2~2, FC3~3,
Distance Based FC0, FC1, FC2, FC4~4, FC5~5,
Inter-frequency FC3, FC4, FC5, FC6~6, FC7~7,
Handover Enumeration Type FC6, FC7, FC8, FC8~8, FC9~9, None
Intra-LTE Load FC9, FC11, FC13, FC11~10,
Balancing FC15, FC17, FC19 FC13~11,
LBFD-00201805 / FC15~12,
TDLBFD- FC17~13, FC19~14
00201805:Service
Based Inter-
frequency
Handover
PS Inter-RAT
Mobility between E-
FC0~0, FC1~1,
UTRAN and
FC2~2, FC3~3,
GERAN
FC0, FC1, FC2, FC4~4, FC5~5,
Inter-RAT Load
FC3, FC4, FC5, FC6~6, FC7~7,
Sharing to GERAN
Enumeration Type FC6, FC7, FC8, FC8~8, FC9~9, None
FC9, FC11, FC13, FC11~10,
RAT handover to
FC15, FC17, FC19 FC13~11,
GERAN
FC15~12,
Distance based
FC17~13, FC19~14
inter-RAT handover
to GERAN
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Intra-LTE Load
NOT_CFG~0,
Balancing Enumeration Type NOT_CFG, CFG None
CFG~1
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
LOFD-001043 /
TDLOFD-
001043:Service
based inter-RAT
handover to
UTRAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to UTRAN
Distance based
inter-RAT handover
Inter-frequency
Handover
Distance Based
Inter-frequency
Handover
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Intra-LTE Load
Balancing Interval Type -141~-43 N/A dBm
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
LOFD-001043 /
TDLOFD-
001043:Service
based inter-RAT
handover to
UTRAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to UTRAN
Distance based
inter-RAT handover
High Speed Mobility

NOT_CFG~0,
Ultra High Speed Enumeration Type NOT_CFG, CFG None
CFG~1
Mobility
T_CRMAX_30S(30
s),
T_CRMAX_30S~0,
T_CRMAX_60S(60
T_CRMAX_60S~1,
s),
High Speed Mobility T_CRMAX_120S~2
T_CRMAX_120S(1
Ultra High Speed Enumeration Type , s
20s),
Mobility T_CRMAX_180S~3
T_CRMAX_180S(1
,
80s),
T_CRMAX_240S~4
T_CRMAX_240S(2
40s)
T_CRMAXHYST_3 T_CRMAXHYST_3
0S(30s), 0S~0,
0S(60s), 0S~1,
High Speed Mobility
Ultra High Speed Enumeration Type s
20S(120s), 20S~2,
Mobility
80S(180s), 80S~3,
40S(240s) 40S~4
High Speed Mobility Interval Type 1~16 N/A None
High Speed Mobility

Ultra High Speed Interval Type 1~16 N/A None
Mobility
TTT_SF_MEDIUM_ TTT_SF_MEDIUM_
0DOT25(0.25), 0DOT25~0,
0DOT50(0.5), 0DOT50~1,
High Speed Mobility Enumeration Type None
0DOT75(0.75), 0DOT75~2,
LDOT0(1) LDOT0~3
TTT_SF_HIGH_0D TTT_SF_HIGH_0D
OT25(0.25), OT25~0,
High Speed Mobility
OT50(0.5), OT50~1,
Ultra High Speed Enumeration Type None
Mobility
OT75(0.75), OT75~2,
TTT_SF_HIGH_LD TTT_SF_HIGH_LD
OT0(1) OT0~3
PS Inter-RAT
Mobility between E-
FC0~0, FC1~1,
UTRAN and
FC2~2, FC3~3,
UTRAN
FC0, FC1, FC2, FC4~4, FC5~5,
Inter-RAT Load
FC3, FC4, FC5, FC6~6, FC7~7,
Sharing to UTRAN
FC9, FC11, FC13, FC11~10,
RAT handover to
FC15, FC17, FC19 FC13~11,
UTRAN
FC15~12,
Distance based
FC17~13, FC19~14
inter-RAT handover
to UTRAN
PS Inter-RAT
Mobility between E-
FC0~0, FC1~1,
UTRAN and
FC2~2, FC3~3,
UTRAN
FC0, FC1, FC2, FC4~4, FC5~5,
Inter-RAT Load
FC3, FC4, FC5, FC6~6, FC7~7,
Sharing to UTRAN
FC9, FC11, FC13, FC11~10,
RAT handover to
FC15, FC17, FC19 FC13~11,
UTRAN
FC15~12,
Distance based
FC17~13, FC19~14
inter-RAT handover
to UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
SRVCC to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
SRVCC to UTRAN
RAT handover to
UTRAN
RAT handover to
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
SRVCC to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000 r1(1), r2(2), r4(4),
r1~0, r2~1, r4~2,
PS Inter-RAT r8(8), r16(16),
Enumeration Type r8~3, r16~4, r32~5, None
Mobility between E- r32(32), r64(64),
r64~6, Infinity~7
UTRAN and Infinity(Infinity)
UTRAN
SRVCC to UTRAN
RAT handover to
UTRAN
RAT handover to
GERAN
120ms~0,
240ms~1,
PS Inter-RAT 480ms~2,
GERAN 1024ms, 2048ms, 2048ms~5,
SRVCC to GERAN 5120ms, 10240ms, 5120ms~6,
Service based inter- 1min, 6min, 12min, 10240ms~7,
RAT handover to 30min, 60min 1min~8, 6min~9,
GERAN 12min~10,
30min~11,
60min~12
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN_RSCP, UTRAN_RSCP~0,
UTRAN
Enumeration Type UTRAN_ECN0, UTRAN_ECN0~1, None
SRVCC to UTRAN
UTRAN_BOTH UTRAN_BOTH~2
RAT handover to
UTRAN
120ms~0,
240ms~1,
PS Inter-RAT 480ms~2,
UTRAN 1024ms, 2048ms, 2048ms~5,
SRVCC to UTRAN 5120ms, 10240ms, 5120ms~6,
Service based inter- 1min, 6min, 12min, 10240ms~7,
RAT handover to 30min, 60min 1min~8, 6min~9,
UTRAN 12min~10,
30min~11,
60min~12
PILOT_STRENGTH
PS Inter-RAT PILOT_STRENGTH
~0,
Mobility between E- ,
Enumeration Type PILOT_PN_PHASE None
UTRAN and PILOT_PN_PHASE
_AND_STRENGTH
CDMA2000 _AND_STRENGTH
~1
120ms~0,
240ms~1,
480ms~2,
120ms, 240ms, 640ms~3,
UTRAN and 5120ms, 10240ms, 5120ms~6,
CDMA2000 1min, 6min, 12min, 10240ms~7,
30min, 60min 1min~8, 6min~9,
12min~10,
30min~11,
60min~12
PS Inter-RAT
Mobility between E- PILOT_STRENGTH
Enumeration Type PILOT_STRENGTH None
UTRAN and ~0
CDMA2000
120ms~0,
240ms~1,
480ms~2,
120ms, 240ms, 640ms~3,
UTRAN and 5120ms, 10240ms, 5120ms~6,
CDMA2000 1min, 6min, 12min, 10240ms~7,
12min~10,
30min~11,
60min~12
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
SRVCC to GERAN
PS Inter-RAT
Mobility between E- RSRP, RSRQ, RSRP~0, RSRQ~1,
UTRAN and BOTH BOTH~2
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
SRVCC to UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
SRVCC to GERAN
PS Inter-RAT
Mobility between E- EventB1(EventB1), EventB1~0,
UTRAN and EventB2(EventB2) EventB2~1
CDMA2000
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
SRVCC to UTRAN
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover r1(1), r2(2), r4(4),
r1~0, r2~1, r4~2,
Coverage Based r8(8), r16(16),
Inter-frequency r32(32), r64(64),
r64~6, Infinity~7
Handover Infinity(Infinity)
Intra-LTE Load
Balancing
Coverage Based
Intra-frequency Enumeration Type RSRP, RSRQ RSRP~0, RSRQ~1 None
Handover
Coverage Based SAME_AS_TRIG_
SAME_AS_TRIG_
Intra-frequency Enumeration Type QUAN(Same as None
QUAN~0, BOTH~1
Handover Trig Quan), BOTH
120ms~0,
240ms~1,
480ms~2,
120ms, 240ms, 640ms~3,
Coverage Based
480ms, 640ms, 1024ms~4,
Intra-frequency
1024ms, 2048ms, 2048ms~5,
Handover Enumeration Type None
5120ms, 10240ms, 5120ms~6,
Intra-LTE Load
1min, 6min, 12min, 10240ms~7,
Balancing
12min~10,
30min~11,
60min~12
Coverage Based
Inter-frequency SAME_AS_TRIG_
SAME_AS_TRIG_
Handover Enumeration Type QUAN(Same as None
QUAN~0, BOTH~1
Intra-LTE Load Trig Quan), BOTH
Balancing
120ms~0,
240ms~1,
480ms~2,
120ms, 240ms, 640ms~3,
Coverage Based
480ms, 640ms, 1024ms~4,
Inter-frequency
1024ms, 2048ms, 2048ms~5,
Handover Enumeration Type None
5120ms, 10240ms, 5120ms~6,
Intra-LTE Load
1min, 6min, 12min, 10240ms~7,
Balancing
12min~10,
30min~11,
60min~12
Coverage Based
RSRP, RSRQ, RSRP~0, RSRQ~1,
BOTH BOTH~2
Handover
Coverage Based
BOTH BOTH~2
Handover
Coverage Based
BOTH BOTH~2
Handover
3GPP R8
Specifications
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
128ms, 160ms, 256ms~7,
CS Fallback to 256ms, 320ms, 320ms~8,
Enumeration Type ms
UTRAN 480ms, 512ms, 480ms~9,
640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
128ms, 160ms, 256ms~7,
CS Fall Back to 256ms, 320ms, 320ms~8,
Enumeration Type ms
GERAN 480ms, 512ms, 480ms~9,
640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
128ms, 160ms, 256ms~7,
CS Fallback to 256ms, 320ms, 320ms~8,
Enumeration Type ms
CDMA2000 1xRTT 480ms, 512ms, 480ms~9,
640ms, 1024ms, 512ms~10,
1280ms, 2560ms, 640ms~11,
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
CS Fallback to
UTRAN
CS Fallback to
UTRAN
CS Fall Back to
GERAN
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
3GPP R8
NOT_CFG(Not
Specifications NOT_CFG~0,
Enumeration Type configure), None
Broadcast of CFG~1
CFG(Configure)
system information
BOOLEAN_FALSE( BOOLEAN_FALSE
False), ~0,
Emergency Call Enumeration Type None
BOOLEAN_TRUE( BOOLEAN_TRUE~
True) 1
3GPP R8
NOT_CFG(Not
Broadcast of CFG~1
CFG(Configure)
system information
P00(0%), P05(5%),
P10(10%),
P15(15%),
P20(20%),
P00~0, P05~1,
P25(25%),
P10~2, P15~3,
P30(30%),
3GPP R8 P20~4, P25~5,
P40(40%),
Specifications P30~6, P40~7,
Enumeration Type P50(50%), %
Broadcast of P50~8, P60~9,
P60(60%),
system information P70~10, P75~11,
P70(70%),
P80~12, P85~13,
P75(75%),
P90~14, P95~15
P80(80%),
P85(85%),
P90(90%),
P95(95%)
ACCESS_BARRIN
G_TIME_S4(4s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S4~0,
G_TIME_S8(8s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S8~1,
G_TIME_S16(16s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S16~2,
G_TIME_S32(32s),
3GPP R8 ACCESS_BARRIN
ACCESS_BARRIN
Specifications G_TIME_S32~3,
Enumeration Type G_TIME_S64(64s), s
Broadcast of ACCESS_BARRIN
ACCESS_BARRIN
system information G_TIME_S64~4,
G_TIME_S128(128
ACCESS_BARRIN
s),
G_TIME_S128~5,
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S256(256
G_TIME_S256~6,
s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S512~7
G_TIME_S512(512
s)
3GPP R8 BOOLEAN_FALSE( BOOLEAN_FALSE

Specifications False), ~0,
Broadcast of BOOLEAN_TRUE( BOOLEAN_TRUE~
system information True) 1


3GPP R8
NOT_CFG(Not
Broadcast of CFG~1
CFG(Configure)
system information
P00(0%), P05(5%),
P10(10%),
P15(15%),
P20(20%),
P00~0, P05~1,
P25(25%),
P10~2, P15~3,
P30(30%),
3GPP R8 P20~4, P25~5,
P40(40%),
Specifications P30~6, P40~7,
Enumeration Type P50(50%), %
Broadcast of P50~8, P60~9,
P60(60%),
system information P70~10, P75~11,
P70(70%),
P80~12, P85~13,
P75(75%),
P90~14, P95~15
P80(80%),
P85(85%),
P90(90%),
P95(95%)
ACCESS_BARRIN
G_TIME_S4(4s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S4~0,
G_TIME_S8(8s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S8~1,
G_TIME_S16(16s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S16~2,
G_TIME_S32(32s),
3GPP R8 ACCESS_BARRIN
ACCESS_BARRIN
Specifications G_TIME_S32~3,
Enumeration Type G_TIME_S64(64s), s
Broadcast of ACCESS_BARRIN
ACCESS_BARRIN
system information G_TIME_S64~4,
G_TIME_S128(128
ACCESS_BARRIN
s),
G_TIME_S128~5,
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S256(256
G_TIME_S256~6,
s),
ACCESS_BARRIN
ACCESS_BARRIN
G_TIME_S512~7
G_TIME_S512(512
s)


3GPP R8
Specifications
3GPP R8
Specifications
Broadcast of
CELL_BARRED(Ba
system information CELL_BARRED~0,
rred),
Cell Selection and Enumeration Type CELL_NOT_BARR None
CELL_NOT_BARR
Reselection ED~1
ED(Not Barred)
Cell Outage
Detection and
Compensation
3GPP R8
CELL_RESERVED(
Specifications CELL_RESERVED
Reserved),
Broadcast of ~0,
Enumeration Type CELL_NOT_RESE None
system information CELL_NOT_RESE
RVED(Not
Cell Selection and RVED~1
Reserved)
Re-selection
3GPP R8
Specifications
Broadcast of ALLOWED, ALLOWED~0,
system information NOT_ALLOWED NOT_ALLOWED~1
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of NORMAL_MODE(N
system information ormal mode), NORMAL_MODE~
Cell Selection and RR_MODE(Round 0, RR_MODE~1
Reselection Robin Mode)
RAN Sharing with
Common Carrier
3GPP R8
Specifications
Broadcast of
system information
Interval Type 1~720 N/A h
Cell Selection and
Reselection
RAN Sharing with
Common Carrier
3GPP R8
Specifications
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Reselection
RAN Sharing with
Common Carrier
3GPP R8 CELL_RESERVED
Specifications _FOR_OP(Reserve CELL_RESERVED
Broadcast of d), _FOR_OP~0,
system information CELL_NOT_RESE CELL_NOT_RESE
Cell Selection and RVED_FOR_OP(N RVED_FOR_OP~1
Re-selection ot Reserved)
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Reselection
RAN Sharing with
Common Carrier
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Reselection
RAN Sharing with
Common Carrier
3GPP R8
Specifications
DB1_Q_HYST(1dB)
,
DB2_Q_HYST(2dB)
,
DB0_Q_HYST~0,
DB3_Q_HYST(3dB)
DB1_Q_HYST~1,
,
DB2_Q_HYST~2,
DB4_Q_HYST(4dB)
DB3_Q_HYST~3,
,
DB4_Q_HYST~4,
DB5_Q_HYST(5dB)
DB5_Q_HYST~5,
,
DB6_Q_HYST~6,
DB6_Q_HYST(6dB)
DB8_Q_HYST~7,
3GPP R8 ,
DB10_Q_HYST~8,
Specifications DB8_Q_HYST(8dB)
DB12_Q_HYST~9,
Broadcast of ,
Enumeration Type DB14_Q_HYST~10 dB
system information DB10_Q_HYST(10
,
Cell Selection and dB),
DB16_Q_HYST~11
Re-selection DB12_Q_HYST(12
,
dB),
DB18_Q_HYST~12
DB14_Q_HYST(14
,
dB),
DB20_Q_HYST~13
DB16_Q_HYST(16
,
dB),
DB22_Q_HYST~14
DB18_Q_HYST(18
,
dB),
DB24_Q_HYST~15
DB20_Q_HYST(20
dB),
DB22_Q_HYST(22
dB),
3GPP R8
Specifications
NOT_CFG(Not
Broadcast of NOT_CFG~0,
system information CFG~1
CFG(Configure)
Cell Selection and
Re-selection
S30_T_EVALULATI S30_T_EVALULATI
ON(30s), ON~0,
3GPP R8 S60_T_EVALULATI S60_T_EVALULATI
Specifications ON(60s), ON~1,
Broadcast of S120_T_EVALULA S120_T_EVALULA
Enumeration Type s
system information TION(120s), TION~2,
Cell Selection and S180_T_EVALULA S180_T_EVALULA
Re-selection TION(180s), TION~3,
S240_T_EVALULA S240_T_EVALULA
TION(240s) TION~4
S30_T_HYST_NOR S30_T_HYST_NOR
MAL(30s), MAL~0,
3GPP R8 S60_T_HYST_NOR S60_T_HYST_NOR
Specifications MAL(60s), MAL~1,
Broadcast of S120_T_HYST_NO S120_T_HYST_NO
Enumeration Type s
system information RMAL(120s), RMAL~2,
Cell Selection and S180_T_HYST_NO S180_T_HYST_NO
Re-selection RMAL(180s), RMAL~3,
S240_T_HYST_NO S240_T_HYST_NO
RMAL(240s) RMAL~4
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
DB_6_Q_HYST_SF DB_6_Q_HYST_SF
3GPP R8 _MEDIUM(-6dB), _MEDIUM~0,
Specifications DB_4_Q_HYST_SF DB_4_Q_HYST_SF
Broadcast of _MEDIUM(-4dB), _MEDIUM~1,
Enumeration Type dB
system information DB_2_Q_HYST_SF DB_2_Q_HYST_SF
Cell Selection and _MEDIUM(-2dB), _MEDIUM~2,
Re-selection DB0_Q_HYST_SF_ DB0_Q_HYST_SF_
MEDIUM(0dB) MEDIUM~3
DB_6_Q_HYST_SF DB_6_Q_HYST_SF
3GPP R8 _HIGH(-6dB), _HIGH~0,
Specifications DB_4_Q_HYST_SF DB_4_Q_HYST_SF
Broadcast of _HIGH(-4dB), _HIGH~1,
Enumeration Type dB
system information DB_2_Q_HYST_SF DB_2_Q_HYST_SF
Cell Selection and _HIGH(-2dB), _HIGH~2,
Re-selection DB0_Q_HYST_SF_ DB0_Q_HYST_SF_
HIGH(0dB) HIGH~3
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
Interval Type 0~31 N/A 2dB
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Reselection
3GPP R8
Specifications
Broadcast of
Interval Type -70~-22 N/A 2dBm
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
Interval Type -30~33 N/A dBm
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8 MBW6(1.4M), MBW6~0,
Specifications MBW15(3M), MBW15~1,
Broadcast of MBW25(5M), MBW25~2,
Enumeration Type MHz
system information MBW50(10M), MBW50~3,
Cell Selection and MBW75(15M), MBW75~4,
Re-selection MBW100(20M) MBW100~5
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
T_RESEL_SF_0DO T_RESEL_SF_0DO
3GPP R8 T25(0.25), T25~0,
Specifications T_RESEL_SF_0DO T_RESEL_SF_0DO
Broadcast of T5(0.5), T5~1,
system information T_RESEL_SF_0DO T_RESEL_SF_0DO
Cell Selection and T75(0.75), T75~2,
Re-selection T_RESEL_SF_1DO T_RESEL_SF_1DO
T0(1.0) T0~3
3GPP R8 T25(0.25), T25~0,
T0(1.0) T0~3
3GPP R8
Specifications BitString00(00), BitString00~0,
Broadcast of BitString01(01), BitString01~1,
system information BitString10(10), BitString10~2,
Cell Selection and BitString11(11) BitString11~3
Re-selection
3GPP R8
Specifications BOOLEAN_FALSE( BOOLEAN_FALSE
Broadcast of False), ~0,
system information BOOLEAN_TRUE( BOOLEAN_TRUE~
Cell Selection and True) 1
Re-selection
Broadcast of
system information
Cell Selection and
Re-selection
Broadcast of
system information
Cell Selection and
Re-selection
Broadcast of
NOT_CFG(Not
system information NOT_CFG~0,
Cell Selection and CFG~1
CFG(Configure)
Re-selection
Broadcast of
system information
Cell Selection and
Re-selection
Broadcast of
NOT_CFG(Not
CFG(Configure)
Re-selection
Broadcast of
system information
Interval Type -34~-3 N/A dB
Cell Selection and
Re-selection
3GPP R8
Specifications
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8 T25(0.25), T25~0,
T0(1.0) T0~3
3GPP R8 T25(0.25), T25~0,
T0(1.0) T0~3
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
NOT_CFG(Not
CFG(Configure)
Reselection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of BOOLEAN_FALSE( BOOLEAN_FALSE
system information False), ~0,
Cell Selection and BOOLEAN_TRUE( BOOLEAN_TRUE~
Re-selection True) 1
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fallback to
CDMA2000 1xRTT
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of Character String
system information Type
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R8 T25(0.25), T25~0,
T0(1.0) T0~3
3GPP R8 T25(0.25), T25~0,
T0(1.0) T0~3
3GPP R9
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R9
Specifications
NOT_CFG(Not
CFG(Configure)
Cell Selection and
Re-selection
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R9
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
CS Fall Back to 1x
RTT
3GPP R8
Specifications
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
NOT_CFG(Not
CFG(Configure)
Re-selection
Mobility
Management
3GPP R8 T_RESEL_SF_0DO T_RESEL_SF_0DO
Specifications T25(0.25), T25~0,
Broadcast of T_RESEL_SF_0DO T_RESEL_SF_0DO
system information T5(0.5), T5~1,
Cell Selection and T_RESEL_SF_0DO T_RESEL_SF_0DO
Re-selection T75(0.75), T75~2,
Mobility T_RESEL_SF_1DO T_RESEL_SF_1DO
Management T0(1.0) T0~3

3GPP R8
Specifications
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
NOT_CFG(Not
CFG(Configure)
Re-selection
Mobility
Management

Reselection T75(0.75), T75~2,
3GPP R8
Specifications
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications
Broadcast of
system information
Cell Selection and
Re-selection
Broadcast of
system information
Cell Selection and
Re-selection
Broadcast of
NOT_CFG(Not
CFG(Configure)
Re-selection
Broadcast of
system information
Cell Selection and
Re-selection
3GPP R8
Specifications

RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
Specifications RF32~2, RF64~3,
Enumeration Type radio frames), None
Broadcast of RF128~4,
RF128(128 radio
system information RF256~5, RF512~6
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
RF8(8 radio
frames), RF16(16
radio frames),
RF32(32 radio
3GPP R8 RF8~0, RF16~1,
frames), RF64(64
RF128(128 radio
frames), RF256(256
radio frames),
RF512(512 radio
frames)
3GPP R8
Specifications
Broadcast of
system information
3GPP R8
Specifications MERGE~0,
Enumeration Type MERGE, DISCARD None
Broadcast of DISCARD~1
system information
3GPP R8
Specifications MERGE~0,
Enumeration Type MERGE, DISCARD None
Broadcast of DISCARD~1
system information
3GPP R8
Specifications
3GPP R8 AL0(0), AL04(0.4),
Specifications AL05(0.5), AL0~0, AL04~1,
Broadcast of AL06(0.6), AL05~2, AL06~3,
system information AL07(0.7), AL07~4, AL08~5,
Uplink Power AL08(0.8), AL09~6, AL1~7
Control AL09(0.9), AL1(1)
3GPP R8
Specifications
Broadcast of
system information
Uplink Power
Control
3GPP R8
Specifications
Broadcast of
system information
Uplink Power
Control
3GPP R8
Specifications
DELTAF_2(-2dB), DELTAF_2~0,
Broadcast of
Enumeration Type DELTAF0(0dB), DELTAF0~1, dB
system information
DELTAF2(2dB) DELTAF2~2
Uplink Power
Control
3GPP R8
Specifications
DELTAF1(1dB), DELTAF1~0,
Broadcast of
system information
Uplink Power
Control
3GPP R8
Specifications DELTAF_2(-2dB), DELTAF_2~0,
Broadcast of DELTAF0(0dB), DELTAF0~1,
Enumeration Type dB
system information DELTAF1(1dB), DELTAF1~2,
Uplink Power DELTAF2(2dB) DELTAF2~3
Control
3GPP R8
Specifications
Broadcast of
system information
Uplink Power
Control
3GPP R8
Specifications
Broadcast of
system information
Uplink Power
Control
3GPP R8
Specifications
Broadcast of
Interval Type -1~6 N/A 2dB
system information
Uplink Power
Control











3GPP R8
Specifications
SF500(500
subframes),
SF750(750
subframes),
SF500~0,
SF1280(1280
SF750~1,
subframes),
3GPP R8 SF1280~2,
SF1920(1920
Specifications SF1920~3,
Enumeration Type subframes), None
Broadcast of SF2560~4,
SF2560(2560
system information SF5120~5,
subframes),
SF10240~6,
SF5120(5120
INFINITY~7
subframes),
SF10240(10240
subframes),
INFINITY(Infinity)
3GPP R8
Specifications
MS100_T300(100m
s),
MS200_T300(200m
s),
MS300_T300(300m MS100_T300~0,
s), MS200_T300~1,
3GPP R8 MS400_T300(400m MS300_T300~2,
Specifications s), MS400_T300~3,
Enumeration Type ms
Broadcast of MS600_T300(600m MS600_T300~4,
system information s), MS1000_T300~5,
MS1000_T300(100 MS1500_T300~6,
0ms), MS2000_T300~7
MS1500_T300(150
0ms),
MS2000_T300(200
0ms)
MS100_T301(100m
s),
MS200_T301(200m
s),
MS300_T301(300m MS100_T301~0,
s), MS200_T301~1,
3GPP R8 MS400_T301(400m MS300_T301~2,
Specifications s), MS400_T301~3,
Enumeration Type ms
Broadcast of MS600_T301(600m MS600_T301~4,
system information s), MS1000_T301~5,
MS1000_T301(100 MS1500_T301~6,
0ms), MS2000_T301~7
MS1500_T301(150
0ms),
MS2000_T301(200
0ms)
MS0_T310(0ms),
MS50_T310(50ms),
MS100_T310(100m
MS0_T310~0,
s),
MS50_T310~1,
3GPP R8 MS200_T310(200m
MS100_T310~2,
Specifications s),
Broadcast of MS500_T310(500m
MS500_T310~4,
system information s),
MS1000_T310~5,
MS1000_T310(100
MS2000_T310~6
0ms),
MS2000_T310(200
0ms)
MS1000_T311(100
0ms),
MS3000_T311(300
0ms),
MS1000_T311~0,
MS5000_T311(500
MS3000_T311~1,
3GPP R8 0ms),
MS5000_T311~2,
Specifications MS10000_T311(10
Broadcast of 000ms),
MS15000_T311~4,
system information MS15000_T311(15
MS20000_T311~5,
000ms),
MS30000_T311~6
MS20000_T311(20
000ms),
MS30000_T311(30
000ms)
3GPP R8
n1(1), n2(2), n3(3), n1~0, n2~1, n3~2,
Specifications
Broadcast of
n8(8), n10(10) n8~6, n10~7
system information
3GPP R8
n1(1), n2(2), n3(3), n1~0, n2~1, n3~2,
Specifications
Broadcast of
n10(10), n20(20) n10~6, n20~7
system information
Character String
Type

True) 1
Broadcast of
NORMAL_CP(Nor
system information
mal), NORMAL_CP~0,
CP length Enumeration Type None
EXTENDED_CP(Ex EXTENDED_CP~1
Normal CP
tended)
Extended CP
NORMAL_CP(Nor
CP length
mal), NORMAL_CP~0,
Normal CP Enumeration Type None
EXTENDED_CP(Ex EXTENDED_CP~1
Extended CP
tended)
Broadcast of
system information
3GPP R9
Specifications
3GPP R10
Specifications
NOT_CFG(Not
CFG(Configure)
Broadcast of
system information
3GPP R9 18000~45589,6443
Specifications 6~65535
3GPP R10
Specifications
Broadcast of
system information
3GPP R9 0~45589,64436~65
Specifications 535
3GPP R10
Specifications
CELL_BW_N6(1.4
M),
CELL_BW_N15(3M
), CELL_BW_N6~0,
CELL_BW_N25(5M CELL_BW_N15~1,
Scalable Bandwidth
), CELL_BW_N25~2,
Broadcast of Enumeration Type None
CELL_BW_N50(10 CELL_BW_N50~3,
system information
M), CELL_BW_N75~4,
CELL_BW_N75(15 CELL_BW_N100~5
M),
CELL_BW_N100(2
0M)
CELL_BW_N6(1.4
M),
CELL_BW_N15(3M
), CELL_BW_N6~0,
CELL_BW_N25(5M CELL_BW_N15~1,
Scalable Bandwidth
), CELL_BW_N25~2,
Broadcast of Enumeration Type None
CELL_BW_N50(10 CELL_BW_N50~3,
system information
M), CELL_BW_N75~4,
CELL_BW_N75(15 CELL_BW_N100~5
M),
CELL_BW_N100(2
0M)
Broadcast of
system information
Broadcast of
system information
Broadcast of
system information
CELL_DEACTIVE(
Deactivated), CELL_DEACTIVE~
CELL_ACTIVE(Acti 0, CELL_ACTIVE~1
ve)
CELL_UNBLOCK(U CELL_UNBLOCK~
nblock), 0,
CELL_HIGH_BLOC CELL_HIGH_BLOC
K(High block), K~1,
CELL_MIDDLE_BL CELL_MIDDLE_BL
OCK(Middle block), OCK~2,
CELL_LOW_BLOC CELL_LOW_BLOC
K(Low block) K~3

Broadcast of CELL_FDD(FDD), CELL_FDD~0,
system information CELL_TDD(TDD) CELL_TDD~1
Broadcast of
system information
SA0(SA0),
uplink-downlink
SA1(SA1),
subframe SA0~0, SA1~1,
SA2(SA2),
configuration SA2~2, SA3~3,
Enumeration Type SA3(SA3), None
type1&2 SA4~4, SA5~5,
SA4(SA4),
uplink-downlink SA6~6
SA5(SA5),
subframe
SA6(SA6)
configuration type
0/5
Broadcast of
system information SSP0(SSP0),
uplink-downlink SSP1(SSP1),
special subframe SSP2(SSP2), SSP0~0, SSP1~1,
configuration type 7 SSP3(SSP3), SSP2~2, SSP3~3,
uplink-downlink Enumeration Type SSP4(SSP4), SSP4~4, SSP5~5, None
special subframe SSP5(SSP5), SSP6~6, SSP7~7,
configuration type 4 SSP6(SSP6), SSP8~8
uplink-downlink SSP7(SSP7),
special subframe SSP8(SSP8)
configuration type 5
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
dB0(0dB), dB-3~12, dB-2~13,
dB1(1dB), dB-1~14, dB0~15,
None Enumeration Type dB
dB2(2dB), dB1~16, dB2~17,
dB3(3dB), dB3~18, dB4~19,
dB4(4dB), dB5~20, dB6~21,
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
dB0(0dB), dB-3~12, dB-2~13,
dB1(1dB), dB-1~14, dB0~15,
None Enumeration Type dB
dB2(2dB), dB1~16, dB2~17,
dB3(3dB), dB3~18, dB4~19,
dB4(4dB), dB5~20, dB6~21,
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
Random Access
Procedure
LOW_SPEED(Low
speed cell flag),
HIGH_SPEED(High LOW_SPEED~0,
speed cell flag), HIGH_SPEED~1,
High Speed Mobility
ULTRA_HIGH_SPE ULTRA_HIGH_SPE
Ultra High Speed Enumeration Type None
ED(Ultra high ED~2,
Mobility
speed cell flag), EXTRA_HIGH_SPE
EXTRA_HIGH_SPE ED~3
ED(Extra high
speed cell flag)
Random Access
Procedure
Random Access
Interval Type 1~100000 N/A m
Procedure
Compact NOT_CFG(Not
NOT_CFG~0,
Bandwidth Enumeration Type configure), None
CFG~1
Scalable Bandwidth CFG(Configure)
Compact
48~50,96~100,146
Bandwidth Interval Type N/A 0.1MHz
~150,183~200
Scalable Bandwidth
Compact
48~50,96~100,146
Bandwidth Interval Type N/A 0.1MHz
~150,183~200
Scalable Bandwidth
NOT_CFG(Not
CFG(Configure)
Broadcast of
system information
3GPP R8
Specifications
NOT_CFG(Not
CFG(Configure)
Uplink Power
Control
3GPP R8
Specifications
Broadcast of
system information
Uplink Power
Control
False), ~0,
SFN Enumeration Type None
True) 1
SFN(SFN),
CELL_COMBINATI
SFN~0,
ON(Cell
CELL_COMBINATI
Combination),
ON~1,
TWO_RRU_COMBI
SFN Enumeration Type TWO_RRU_COMBI None
NATION(TWO RRU
NATION~2,
Combination),
DIGITAL_COMBINA
DIGITAL_COMBINA
TION~3
TION(Cell Digital
Combination)
NO_COMPRESSIO
N(No NO_COMPRESSIO
Compression), N~0,
NORMAL_COMPR NORMAL_COMPR
ESSION(Normal ESSION~1
Compression)
CELL_INST_UNIN
STALL(Uninstall),
CELL_INST_UEM_
CFGING(Inner CELL_INST_UNIN
software module STALL~0,
configuring), CELL_INST_UEM_
CELL_INST_RRU_ CFGING~1,
CFGING(RRU CELL_INST_RRU_
configuring), CFGING~2,
CELL_INST_BBI_C CELL_INST_BBI_C
FGING(BBI FGING~3,
configuring), CELL_INST_RECF
CELL_INST_RECF GING~4,
GING(Recfging), CELL_INST_DELE
CELL_INST_DELE TING~5,
TING(Deleting), CELL_INST_NORM
CELL_INST_NORM AL~6,
AL(Normal), CELL_INST_BARR
CELL_INST_BARR ED~7,
ED(Barred), CELL_INST_ALLO
CELL_INST_ALLO CATING_RES~8,
CATING_RES(Alloc CELL_INST_CRM_
ating resource), CFGING~9
CELL_INST_CRM_
CFGING(RRU
configuring)
C_BASEBAND_RE OURCE_ALLOC_F
SOURCE_ALLOC_ AIL~1973485748,
FAIL(Allocate CCEM_CELLBASI
baseband resource C_BASEBAND_RE
failed), SOURCE_ALLOC_
CCEM_CELLBASI FAIL~1973485749,
C_CARRIER_RES CCEM_CELLBASI
OURCE_CFG_FAIL C_CARRIER_RES
(Failed to config the OURCE_CFG_FAIL
cell's RRU carrier ~1973485752,
resource), CCEM_CELLBASI
CCEM_CELLBASI C_ERR_TDD_MIM
C_ERR_TDD_MIM O_NOT_SUPPORT
O_NOT_SUPPORT _8T8R~197348575
_8T8R(TDD MIMO 6,
cannot support CCEM_CELLBASI
8T8R), C_ERR_CR_UL_F
CCEM_CELLBASI REQ_ACT_FAIL~1
None Enumeration Type C_ERR_CR_UL_F 973485757, None
REQ_ACT_FAIL(Se CCEM_CELLBASI
t UL FREQ Failed), C_ERR_CR_DL_F
CCEM_CELLBASI REQ_ACT_FAIL~1
C_ERR_CR_DL_F 973485758,
REQ_ACT_FAIL(Se CCEM_CELLBASI
t DL FREQ Failed), C_ERR_CR_POW
CCEM_CELLBASI ER_ACT_FAIL~197
C_ERR_CR_POW 3485759,
ER_ACT_FAIL(Set CCEM_CELLBASI
Power Failed), C_ERR_CR_DL_F
CCEM_CELLBASI REQ_POWER_AC
C_ERR_CR_DL_F T_FAIL~197348576
REQ_POWER_AC 0,
T_FAIL(Set DL CCEM_CELLBASI
FREQ and Power C_ERR_SET_RRU
Failed), _FREQ_FAIL~1973
CCEM_CELLBASI 485761,
C_ERR_SET_RRU CCEM_CELLBASI
Character String
Type
(UnBlock Cell),
CELL_NO_OP~0,
CELL_SETUP_HE
CELL_SETUP_ACT
ALCHK(Cell
~1,
Healthy Check),
CELL_SETUP_UBL
CELL_SETUP_141
~2,
(141 Cell Setup),
CELL_SETUP_HE
CELL_SETUP_UL
ALCHK~3,
WIDESCAN(UL
CELL_SETUP_141
Wide Freq Scan
~4,
Cell Setup),
CELL_SETUP_UL
CELL_DEL_BLK_L
WIDESCAN~5,
OW(Block Cell
CELL_DEL_BLK_L
Low),
OW~26,
CELL_DEL_BLK_M
CELL_DEL_BLK_M
ID(Block Cell Mid),
ID~27,
CELL_DEL_BLK_H
CELL_DEL_BLK_H
IGH(Block Cell
IGH~28,
High),
CELL_DEL_NOUS
None Enumeration Type CELL_DEL_NOUS None
ER~29,
ER(Block Cell No
CELL_DEL_DEA~3
User),
0,
CELL_DEL_DEA(D
CELL_DEL_RMV~3
ea Cell),
1,
CELL_DEL_RMV(D
CELl_DEL_HEALC
elete Cell),
HK~32,
CELl_DEL_HEALC
CELL_DEL_UNHE
HK(Cell Healthy
AL~33,
Chk),
CELL_DEL_SETUP
CELL_DEL_UNHE
_FAIL~34,
AL(Cell UnHealthy),
CELL_DEL_141_D
CELL_DEL_SETUP
EL~35,
_FAIL(Cell Setup
CELL_DEL_ULWID
Fail),
ESCAN~36,
CELL_DEL_141_D
CELL_DEL_CELLN
EL(141 Cell Del),
OACCESSALM~11
CELL_DEL_ULWID
2
ESCAN(UL Wide
Character String
Type
(UnBlock Cell),
CELL_NO_OP~0,
CELL_SETUP_HE
CELL_SETUP_ACT
ALCHK(Cell
~1,
Healthy Check),
CELL_SETUP_UBL
CELL_SETUP_141
~2,
(141 Cell Setup),
CELL_SETUP_HE
CELL_SETUP_UL
ALCHK~3,
WIDESCAN(UL
CELL_SETUP_141
Wide Freq Scan
~4,
Cell Setup),
CELL_SETUP_UL
CELL_DEL_BLK_L
WIDESCAN~5,
OW(Block Cell
CELL_DEL_BLK_L
Low),
OW~26,
CELL_DEL_BLK_M
CELL_DEL_BLK_M
ID(Block Cell Mid),
ID~27,
CELL_DEL_BLK_H
CELL_DEL_BLK_H
IGH(Block Cell
IGH~28,
High),
CELL_DEL_NOUS
None Enumeration Type CELL_DEL_NOUS None
ER~29,
ER(Block Cell No
CELL_DEL_DEA~3
User),
0,
CELL_DEL_DEA(D
CELL_DEL_RMV~3
ea Cell),
1,
CELL_DEL_RMV(D
CELl_DEL_HEALC
elete Cell),
HK~32,
CELl_DEL_HEALC
CELL_DEL_UNHE
HK(Cell Healthy
AL~33,
Chk),
CELL_DEL_SETUP
CELL_DEL_UNHE
_FAIL~34,
AL(Cell UnHealthy),
CELL_DEL_141_D
CELL_DEL_SETUP
EL~35,
_FAIL(Cell Setup
CELL_DEL_ULWID
Fail),
ESCAN~36,
CELL_DEL_141_D
CELL_DEL_CELLN
EL(141 Cell Del),
OACCESSALM~11
CELL_DEL_ULWID
2
ESCAN(UL Wide
RFSHD(RF
Intelligent
Shutdown Mode),
CELL_PWRSAVE_
CELLSHD(Cell
Intelligent
Shutdown Mode),
CELL_PWRSAVE_ CELL_PWRSAVE_
LOWPWR_CELLU UNINSTALL~0,
SEDPWRRDU(Low CELL_PWRSAVE_
Power RFSHD~1,
Consumption CELL_PWRSAVE_
Mode-Cell Used CELLSHD~2,
Power Reduced), CELL_PWRSAVE_
CELL_PWRSAVE_ LOWPWR_CELLU
LOWPWR_RSPWR SEDPWRRDU~3,
RDU(Low Power CELL_PWRSAVE_
Consumption LOWPWR_RSPWR
None Enumeration Type Mode-Reference RDU~4, None
Signal Power CELL_PWRSAVE_
Reduced), LOWPWR_RFSHD
CELL_PWRSAVE_ ~5,
LOWPWR_RFSHD( CELL_PWRSAVE_
Low Power LOWPWR_CELLS
Consumption HD~6,
Mode-RF AUTO_PWROFF_
Shutdown), ONTIME~7,
CELL_PWRSAVE_ CELL_PWRSAVE_I
LOWPWR_CELLS NTERRAT_CELLS
HD(Low Power HD~8
Consumption
Mode-Cell
Shutdown),
AUTO_PWROFF_
ONTIME(Auto
Power Off On Time
Mode),
BBI_SLOT_0(0),
BBI_SLOT_0~0,
BBI_SLOT_1(1),
BBI_SLOT_1~1,
BBI_SLOT_2(2),
BBI_SLOT_2~2,
BBI_SLOT_3(3),
BBI_SLOT_3~3,
None Enumeration Type BBI_SLOT_4(4), None
BBI_SLOT_4~4,
BBI_SLOT_5(5),
BBI_SLOT_5~5,
BBI_SLOT_INVALI
BBI_SLOT_INVALI
D(Invalid Slot
D~65535
Number)
BASIC_TYPE(Basic
Type),
TWO_RRU_COMBI
NATION_TYPE(TW
O RRU
BASIC_TYPE~0,
Combination Type),
TWO_RRU_COMBI
SFN_TYPE(SFN
NATION_TYPE~2,
Type),
SFN_TYPE~3,
BF_TYPE(BF
BF_TYPE~4,
Type),
MIMO_HELP_TYP
MIMO_HELP_TYP
None Enumeration Type E~6, None
E(Mutual-Aid MIMO
CELL_COMBINATI
Type),
ON_TYPE~14,
CELL_COMBINATI
DIGITAL_COMBINA
ON_TYPE(Cell
TION_TYPE~15,
Combination Type),
INVALID_TYPE~25
DIGITAL_COMBINA
5
TION_TYPE(Cell
Digital Combination
Type),
INVALID_TYPE(Inv
alid Type)
UNINSTALL(Uninst
all), UNINSTALL~0,
None Enumeration Type SYMBOL_SHUTDO SYMBOL_SHUTDO None
WN(Symbol WN~1
shutdown)

Single Streaming
Beamforming
SINGLE_LAYER_B SINGLE_LAYER_B
BEAMFORMING
F(Single-Layer BF), F~0,
AND MIMO Enumeration Type None
DUAL_LAYER_BF( DUAL_LAYER_BF~
ADAPTIVE
Dual-Layer BF) 1
SWITCH (Test
Feature)
120ms~0,
240ms~1,
Downlink Static 480ms~2,
Inter-Cell 120ms, 240ms, 640ms~3,
Interference 480ms, 640ms, 1024ms~4,
Coordination 1024ms, 2048ms, 2048ms~5,
Enumeration Type ms
Downlink Dynamic 5120ms, 10240ms, 5120ms~6,
Inter-Cell 1min, 6min, 12min, 10240ms~7,
Interference 30min, 60min 1min~8, 6min~9,
Coordination 12min~10,
30min~11,
60min~12
Downlink Static
Inter-Cell
Interference
Coordination
Downlink Dynamic
Inter-Cell
Interference
Coordination
Downlink Static
Inter-Cell
Interference r1(1), r2(2), r4(4),
r1~0, r2~1, r4~2,
Coordination r8(8), r16(16),
Downlink Dynamic r32(32), r64(64),
r64~6, Infinity~7
Inter-Cell Infinity(Infinity)
Interference
Coordination
Downlink Static
Inter-Cell
Interference
SAME_AS_TRIG_
Coordination SAME_AS_TRIG_
Enumeration Type QUAN(Same as None
Downlink Dynamic QUAN~0, BOTH~1
Trig Quan), BOTH
Inter-Cell
Interference
Coordination
Downlink Static
Inter-Cell
Interference
Coordination
Enumeration Type RSRP, RSRQ RSRP~0, RSRQ~1 None
Downlink Dynamic
Inter-Cell
Interference
Coordination
Downlink Static
Inter-Cell
Interference
Coordination
Downlink Dynamic
Inter-Cell
Interference
Coordination
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
Downlink Static 0ms, 40ms, 64ms, 128ms~5,
Coordination 256ms, 320ms, 320ms~8,
Downlink Dynamic 480ms, 512ms, 480ms~9,
Coordination 5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
Downlink Static
Inter-Cell
Interference
Coordination
Downlink Dynamic
Inter-Cell
Interference
Coordination
Low Power
Consumption Mode
Low Power
Consumption Mode
Low Power
Consumption Mode
Low Power
Consumption Mode
Low Power
Consumption Mode
Low Power
Interval Type 0~1440 N/A min
Consumption Mode
Low Power
Consumption Mode
Low Power
Consumption Mode
Low Power
Consumption Mode
Low Power
Interval Type -10~0 N/A dB
Consumption Mode
Low Power
Consumption Mode

NOT_CFG(Not
Mobility Robust NOT_CFG~0,
Optimization(MRO) CFG~1
CFG(Configure)
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
dB0(0dB), dB-3~12, dB-2~13,
Mobility Robust dB1(1dB), dB-1~14, dB0~15,
Enumeration Type dB
Optimization(MRO) dB2(2dB), dB1~16, dB2~17,
dB3(3dB), dB3~18, dB4~19,
dB4(4dB), dB5~20, dB6~21,
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
dB0(0dB), dB-3~12, dB-2~13,
Mobility Robust dB1(1dB), dB-1~14, dB0~15,
Enumeration Type dB
Optimization(MRO) dB2(2dB), dB1~16, dB2~17,
dB3(3dB), dB3~18, dB4~19,
dB4(4dB), dB5~20, dB6~21,
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
3GPP R8
Specifications
Admission Control
Congestion Control
Basic Qos
Management
Admission Control
Congestion Control
Basic Qos
Management
3GPP R8
Specifications Interval Type 10~99 N/A %
Admission Control
3GPP R8
Admission Control
3GPP R8
Admission Control
3GPP R8
Admission Control
3GPP R8
Admission Control
3GPP R8
Admission Control
3GPP R8
Admission Control
3GPP R8
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Admission Control
3GPP R8
Admission Control
3GPP R8
Specifications Interval Type 1~15 N/A None
Congestion Control
3GPP R8
Congestion Control
3GPP R8
Specifications
Radio/transport Interval Type 1~15 N/A None
Resource Pre-
emption
3GPP R8
Specifications
Admission Control
Congestion Control
3GPP R8
Specifications
Admission Control
Congestion Control
3GPP R8
Specifications
Admission Control
Congestion Control
3GPP R8
Specifications
Admission Control
Congestion Control
3GPP R8
Specifications Interval Type 0~9000 N/A None
Admission Control
RF Channel
Intelligent Interval Type 0~17 N/A None
Shutdown
RF Channel
Intelligent Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Shutdown
RF Channel
Intelligent Compound Type 00:00:00~23:59:59 N/A None
Shutdown
RF Channel
Intelligent Compound Type 00:00:00~23:59:59 N/A None
Shutdown
RF Channel
Intelligent Interval Type 0~7 N/A dB
Shutdown

Intelligent Power-
Off of Carriers in Interval Type 0~17 N/A None
the Same Coverage
Intelligent Power-
Off of Carriers in Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
the Same Coverage
Intelligent Power-
Off of Carriers in Compound Type 00:00:00~23:59:59 N/A None
the Same Coverage
Intelligent Power-
Off of Carriers in Compound Type 00:00:00~23:59:59 N/A None
the Same Coverage
Intelligent Power-
Off of Carriers in Interval Type 0~100 N/A %
the Same Coverage
Intelligent Power-
the Same Coverage
Intelligent Power-
the Same Coverage
Intelligent Power-
the Same Coverage

120ms~0,
240ms~1,
480ms~2,
Uplink Static Inter-
120ms, 240ms, 640ms~3,
Cell Interference
480ms, 640ms, 1024ms~4,
Coordination
1024ms, 2048ms, 2048ms~5,
Uplink Dynamic Enumeration Type ms
5120ms, 10240ms, 5120ms~6,
Inter-Cell
1min, 6min, 12min, 10240ms~7,
Interference
Coordination
12min~10,
30min~11,
60min~12

Cell Interference
Coordination
Uplink Dynamic Interval Type 1~8 N/A None
Inter-Cell
Interference
Coordination
Cell Interference
r1(1), r2(2), r4(4),
Coordination r1~0, r2~1, r4~2,
r8(8), r16(16),
Uplink Dynamic Enumeration Type r8~3, r16~4, r32~5, None
r32(32), r64(64),
Inter-Cell r64~6, Infinity~7
Infinity(Infinity)
Interference
Coordination
Cell Interference
Coordination SAME_AS_TRIG_
SAME_AS_TRIG_
Uplink Dynamic Enumeration Type QUAN(Same as None
QUAN~0, BOTH~1
Inter-Cell Trig Quan), BOTH
Interference
Coordination
Cell Interference
Coordination
Uplink Dynamic Enumeration Type RSRP, RSRQ RSRP~0, RSRQ~1 None
Inter-Cell
Interference
Coordination

Cell Interference
Coordination
Uplink Dynamic Interval Type 0~30 N/A 0.5dB
Inter-Cell
Interference
Coordination
0ms~0, 40ms~1,
64ms~2, 80ms~3,
100ms~4,
0ms, 40ms, 64ms, 128ms~5,
80ms, 100ms, 160ms~6,
Cell Interference
128ms, 160ms, 256ms~7,
Coordination
256ms, 320ms, 320ms~8,
Uplink Dynamic Enumeration Type ms
480ms, 512ms, 480ms~9,
Inter-Cell
640ms, 1024ms, 512ms~10,
Interference
1280ms, 2560ms, 640ms~11,
Coordination
5120ms 1024ms~12,
1280ms~13,
2560ms~14,
5120ms~15
Cell Interference
Coordination
Uplink Dynamic Interval Type -30~30 N/A 0.5dB
Inter-Cell
Interference
Coordination

ULSCH_STRATEG
ULSCH_STRATEG
Y_EPF(EPF),
Y_EPF~0,
ULSCH_STRATEG
ULSCH_STRATEG
Basic Scheduling Y_MAX_CI(MAX_C
Y_MAX_CI~1,
Enhanced Enumeration Type I), None
ULSCH_STRATEG
Scheduling ULSCH_STRATEG
Y_PF~2,
Y_PF(PF),
ULSCH_STRATEG
ULSCH_STRATEG
Y_RR~3
Y_RR(RR)
ADAPTIVE_HARQ_
ADAPTIVE_HARQ_
SW_ON(On),
SW_ON~0,
ADAPTIVE_HARQ_
UL Synchronous ADAPTIVE_HARQ_
Enumeration Type SW_OFF(Off), None
HARQ SW_OFF~1,
ADAPTIVE_HARQ_
ADAPTIVE_HARQ_
SW_SEMI_ON(Se
SW_SEMI_ON~2
miOn)
AMC Interval Type 1~99 N/A 0.01
Dynamic
Scheduling
Dynamic
Interval Type 1~40 N/A ms
Scheduling
Dynamic
Interval Type 45~1500 N/A byte
Scheduling
HOPPING_OFF(Ho
pping off), HOPPING_OFF~0,
HOPPING_TYPE1( HOPPING_TYPE1~
Basic Scheduling Hopping Type 1), 1,
Enhanced Enumeration Type HOPPING_TYPE2( HOPPING_TYPE2~ None
Scheduling Hopping Type 2), 2,
HOPPING_TYPE2_ HOPPING_TYPE2_
RANDOM(Hopping RANDOM~3
Type 2 Random)
Dynamic
Scheduling
Admission Control
Congestion Control
Dynamic
Interval Type 16~15000 N/A bit
Scheduling
Dynamic
Scheduling











Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network
Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network
Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network
Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network
Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network
Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network
Intelligent Power-
Off of Carriers in
the Same Coverage
of UMTS Network

RachAdjSwitch(Rac
hAdjSwitch),
HoRaSwitch(HoRa
3GPP R8 RachAdjSwitch~0,
Switch),
Specifications HoRaSwitch~1,
UnsyncRaSwitch(U
Random Access Bit Field Type UnsyncRaSwitch~2 None
nsyncRaSwitch),
Procedure , MaksIdxSwitch~3,
MaksIdxSwitch(Mak
RACH Optimization BackOffSwitch~4
sIdxSwitch),
BackOffSwitch(Bac
kOffSwitch)
3GPP R8
SrsSubframeRecfS
Specifications SrsSubframeRecfS
Bit Field Type witch(SrsSubframe None
Physical Channel witch~0
RecfSwitch)
Management
3GPP R8
Specifications PucchSwitch(Pucch
Bit Field Type PucchSwitch~0 None
Physical Channel Switch)
Management
Active Queue
Bit Field Type AqmAlgoSwitch AqmAlgoSwitch~0 None
Management(AQM)
UL 2x2 MU-MIMO
CqiAdjAlgoSwitch~
CQI Adjustment CqiAdjAlgoSwitch,
Bit Field Type 0, None
Dynamic StepVarySwitch
StepVarySwitch~1
Scheduling
RRC Connection
Management
DynAdjVoltSwitch(D
Adaptive Power DynAdjVoltSwitch~
Bit Field Type ynamic Adjust None
Consumption 0
Voltage Switch)
DlSwitch(dlCacSwit
ch),
UlSwitch(ulCacSwit
ch),
DlPredictSwitch(dlC
DlSwitch~0,
acPredictSwitch),
UlSwitch~1,
3GPP R8 UlPredictSwitch(ulC
DlPredictSwitch~2,
Specifications acPredictSwitch),
UlPredictSwitch~3,
Admission Control GbrUsageSwitch(G
GbrUsageSwitch~4,
Congestion Control Bit Field Type brUsedPRbCheckS None
DlLdcSwitch~5,
Radio/transport witch),
UlLdcSwitch~6,
Resource Pre- DlLdcSwitch(dlLdcS
RelDrbSwitch~7,
emption witch),
PreemptionSwitch~
UlLdcSwitch(ulLdcS
8
witch),
RelDrbSwitch(LdcD
rbRelSwitch),
PreemptionSwitch(
PreemptionSwitch)
IntraFreqMlbSwitch(
IntraFreqMlbSwitch)
,
InterFreqMlbSwitch(
IntraFreqMlbSwitch
InterFreqMlbSwitch)
~0,
3GPP R8 ,
InterFreqMlbSwitch
Specifications UtranMlbSwitch(Utr
~1,
Intra-LTE Load anMlbSwitch),
UtranMlbSwitch~2,
Balancing GeranMlbSwitch(G
Bit Field Type GeranMlbSwitch~3, None
Inter-RAT Load eranMlbSwitch),
CdmaMlbSwitch~4,
Sharing to UTRAN CdmaMlbSwitch(Cd
IntraFreqIdleMlbSwi
Inter-RAT Load maMlbSwitch),
tch~5,
Sharing to GERAN IntraFreqIdleMlbSwi
UtranIdleMlbSwitch
tch(IntraFreqIdleMlb
~6
Switch),
UtranIdleMlbSwitch(
UtranIdleMLBSwitc
h)
Physical Channel
PdschSpsPcSwitch
Management PdschSpsPcSwitch,
~0,
Broadcast of PhichInnerLoopPcS
Bit Field Type PhichInnerLoopPcS None
system information witch,
witch~1,
Dynamic Downlink PdcchPcSwitch
PdcchPcSwitch~2
Power Allocation
CloseLoopSpsSwitc
CloseLoopSpsSwitc
h~0,
h,
InnerLoopPuschSwi
InnerLoopPuschSwi
tch~1,
tch,
Broadcast of PhSinrTarUpdateS
PhSinrTarUpdateS
system information witch~2,
Bit Field Type witch, None
Uplink Power InnerLoopPucchSwi
InnerLoopPucchSwi
Control tch~3,
tch,
OiSinrTarUpdateSw
OiSinrTarUpdateSw
itch~4,
itch,
PowerSavingSwitch
PowerSavingSwitch
~5
Single Streaming
Beamforming
Dual streaming
Beamforming
BEAMFORMING Bit Field Type BfSwitch BfSwitch~0 None
AND MIMO
ADAPTIVE
SWITCH (Test
Feature)
FreqSelSwitch(Freq
Basic Scheduling
SelSwitch),
Enhanced
ServiceDiffSwitch(S FreqSelSwitch~0,
Scheduling
erviceDiffSwitch), ServiceDiffSwitch~1
VoIP Semi-
Bit Field Type SpsSchSwitch(Sps , SpsSchSwitch~2, None
persistent
SchSwitch), MBSFNShutDownS
Scheduling
MBSFNShutDownS witch~3
Symbol Power
witch(MBSFNShutD
Saving
ownSwitch)
SpsSchSwitch(Sps
Basic Scheduling
SchSwitch),
Enhanced
SinrAdjustSwitch(Si
Scheduling
nrAdjustSwitch), SpsSchSwitch~0,
VoIP Semi-
PreAllocationSwitch SinrAdjustSwitch~1,
persistent
(PreAllocationSwitc PreAllocationSwitch
Scheduling
Bit Field Type h), ~2, None
UL 2x2 MU-MIMO
UlVmimoSwitch(UlV UlVmimoSwitch~3,
UL 2x4 MU-MIMO
mimoSwitch), TtiBundlingSwitch~
TTI Bundling
TtiBundlingSwitch(T 4, ImIcSwitch~5
800M Self-
tiBundlingSwitch),
interference
ImIcSwitch(ImIcSwit
Cancellation
ch)
RAN Sharing with

Common Carrier
Admission Control
Basic Scheduling
FreqPriorIFHOSwitc
h(FreqPriorIFHOSw FreqPriorIFHOSwitc
Intra-LTE Load itch), h~0,
Bit Field Type None
Balancing FreqPriorIFBlindHO FreqPriorIFBlindHO
Switch(FreqPriorIF Switch~1
BlindHOSwitch)
3GPP R8 MuBfSwitch(MuBfS
Bit Field Type MuBfSwitch~0 None
Specifications witch)
Distance Based
Inter-frequency
Handover
Distance based
Inter-RAT handover Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
to UTRAN
Distance based
Inter-RAT handover
to GERAN
ACBAR_SWITCH_
DYNAMIC(dynamic ACBAR_SWITCH_
3GPP R8 configuration), DYNAMIC~0,
Specifications ACBAR_SWITCH_ ACBAR_SWITCH_
Broadcast of STATIC(static STATIC~1,
system information configuration), ACBAR_SWITCH_
ACBAR_SWITCH_ DISABLE~2
DISABLE(Disable)
Intra-eNodeB UL DISABLE(Disable), DISABLE~0,

CoMP ENABLE(Enable) ENABLE~1
MODE1(DL band
division scheme
Downlink Static
No.1), MODE2(DL
Inter-Cell
band division
Interference MODE1~0,
scheme No.2),
Coordination MODE2~1,
Enumeration Type MODE3(DL band None
Downlink Dynamic MODE3~2,
division scheme
Inter-Cell INVALID~255
No.3),
Interference
INVALID(Invalid DL
Coordination
band division
scheme)
Dynamic Downlink
Power Allocation
Dynamic Downlink
Power Allocation
Dynamic Downlink
Power Allocation
PA_NEG6(-6dB),
PA_NEG4DOT77(-
Dynamic Downlink 4.77dB), PA_NEG6~0,
Power Allocation PA_NEG3(-3dB), PA_NEG4DOT77~1
Downlink Dynamic PA_NEG1DOT77(- , PA_NEG3~2,
Enumeration Type dB
Inter-Cell 1.77dB), PA_NEG1DOT77~3
Interference PA_0(0dB), , PA_0~4, PA_1~5,
Coordination PA_1(1dB), PA_2~6, PA_3~7
PA_2(2dB),
PA_3(3dB)
PA_NEG6(-6dB),
PA_NEG4DOT77(-
Dynamic Downlink 4.77dB), PA_NEG6~0,
Power Allocation PA_NEG3(-3dB), PA_NEG4DOT77~1
Downlink Dynamic PA_NEG1DOT77(- , PA_NEG3~2,
Enumeration Type dB
Inter-Cell 1.77dB), PA_NEG1DOT77~3
Interference PA_0(0dB), , PA_0~4, PA_1~5,
Coordination PA_1(1dB), PA_2~6, PA_3~7
PA_2(2dB),
PA_3(3dB)
Dynamic Downlink
Power Allocation
Dynamic Downlink
Power Allocation

DLSCH_PRI_TYPE DLSCH_PRI_TYPE
_EPF(EPF), _EPF~0,
Basic Scheduling
_PF(PF), _PF~1,
Scheduling
_MAX_CI(MAX C/I), _MAX_CI~2,
_RR(RR) _RR~3
Dynamic
Scheduling
Admission Control
Congestion Control
Dynamic
Scheduling
Dynamic
Scheduling
SW_MAX_SM_RA SW_MAX_SM_RA
NK_1(Rank1), NK_1~0,
DL 2x2 MIMO
DL 4x2 MIMO Enumeration Type None
NK_2(Rank2), NK_2~1,
DL 4X4 MIMO
NK_4(Rank4) NK_4~2
3GPP R8
Specifications
Intra-LTE Load
Balancing
3GPP R8
Specifications
Intra-LTE Load
Balancing
3GPP R8
Specifications
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
LOAD_EXCHANGE
3GPP R8 LOAD_EXCHANGE
_PERIOD_1S(1s),
Specifications _PERIOD_1S~0,
LOAD_EXCHANGE
Intra-LTE Load LOAD_EXCHANGE
_PERIOD_2S(2s),
Balancing _PERIOD_2S~1,
Enumeration Type LOAD_EXCHANGE s
Inter-RAT Load LOAD_EXCHANGE
_PERIOD_5S(5s),
Sharing to UTRAN _PERIOD_5S~2,
LOAD_EXCHANGE
Inter-RAT Load LOAD_EXCHANGE
_PERIOD_10S(10s
Sharing to GERAN _PERIOD_10S~3
)
3GPP R8
Specifications
Intra-LTE Load
Balancing
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
3GPP R8
Specifications
Intra-LTE Load
Balancing
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
3GPP R8
Specifications
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN
3GPP R8
Specifications
Inter-RAT Load
Sharing to UTRAN
Inter-RAT Load
Sharing to GERAN

3GPP R8
Specifications CONGREG_LV4, CONGREG_LV4~2,
Physical Channel CONGREG_LV8 CONGREG_LV8~3
Management
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
Physical Channel
Management

Physical Channel
Management
Sleeping Cell
Detection
Sleeping Cell
Detection
Sleeping Cell
Detection
Sleeping Cell
Detection
MODE1(UL band
division scheme
Uplink Static Inter- No.1), MODE2(UL
Cell Interference band division
MODE1~1,
Coordination scheme No.2),
MODE2~2,
Uplink Dynamic Enumeration Type MODE3(UL band None
MODE3~3,
Inter-Cell division scheme
INVALID~255
Interference No.3),
Coordination INVALID(Invalid UL
band division
scheme)
TM1(TM1),
TM2(TM2), TM1~0, TM2~1,
TM7(TM7), TM7~6, TM8~7
TM8(TM8)
None Interval Type 0~10000 N/A 0.01mW
None Interval Type 0~10000 N/A 0.01mW
3GPP R8
Specifications
MOD_PERIOD_CO MOD_PERIOD_CO
EFF_N2(2), EFF_N2~0,
Broadcast of EFF_N4(4), EFF_N4~1,
system information MOD_PERIOD_CO MOD_PERIOD_CO
EFF_N8(8), EFF_N8~2,
EFF_N16(16) EFF_N16~3
Physical Channel
Management
Broadcast of
system information
Dynamic Downlink
Power Allocation
Physical Channel
Management
Broadcast of
system information
Dynamic Downlink
Power Allocation
Physical Channel
Management
Broadcast of
system information
Dynamic Downlink
Power Allocation
Physical Channel
Management
Broadcast of
system information
Dynamic Downlink
Power Allocation
Physical Channel
Management
Broadcast of
system information Interval Type -3175~3175 N/A 0.005dB
Paging
Dynamic Downlink
Power Allocation
Physical Channel
Management
Broadcast of
system information
Random Access
Procedure
Dynamic Downlink
Power Allocation
LoCation Services
(LCS)

Physical Channel
Management
Broadcast of
Interval Type -600~500 N/A 0.1dBm
system information
Dynamic Downlink
Power Allocation
Physical Channel
Management
Broadcast of
system information
Dynamic Downlink
Power Allocation
3GPP R8
Specifications
DB0_PWR_RAMPI DB0_PWR_RAMPI
NG_STEP(0dB), NG_STEP~0,
3GPP R8 DB2_PWR_RAMPI DB2_PWR_RAMPI
Specifications NG_STEP(2dB), NG_STEP~1,
Enumeration Type dB
Uplink Power DB4_PWR_RAMPI DB4_PWR_RAMPI
Control NG_STEP(4dB), NG_STEP~2,
DB6_PWR_RAMPI DB6_PWR_RAMPI
NG_STEP(6dB) NG_STEP~3
DBM_120(-
120dBm),
DBM_118(-
118dBm),
DBM_116(-
116dBm),
DBM_120~0,
DBM_114(-
DBM_118~1,
114dBm),
DBM_116~2,
DBM_112(-
DBM_114~3,
112dBm),
DBM_112~4,
DBM_110(-
DBM_110~5,
110dBm),
3GPP R8 DBM_108~6,
DBM_108(-
Specifications DBM_106~7,
Enumeration Type 108dBm), dBm
Uplink Power DBM_104~8,
DBM_106(-
Control DBM_102~9,
106dBm),
DBM_100~10,
DBM_104(-
DBM_98~11,
104dBm),
DBM_96~12,
DBM_102(-
DBM_94~13,
102dBm),
DBM_92~14,
DBM_100(-
DBM_90~15
100dBm),
DBM_98(-98dBm),
DBM_96(-96dBm),
DBM_94(-94dBm),
DBM_92(-92dBm),
DBM_90(-90dBm)
B56_MSG_SIZE_G B56_MSG_SIZE_G
ROUPA(56bits), ROUPA~0,
3GPP R8 B144_MSG_SIZE_ B144_MSG_SIZE_
Specifications GROUPA(144bits), GROUPA~1,
Enumeration Type bit
Transport Channel B208_MSG_SIZE_ B208_MSG_SIZE_
Management GROUPA(208bits), GROUPA~2,
B256_MSG_SIZE_ B256_MSG_SIZE_
GROUPA(256bits) GROUPA~3
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
NOT_CFG(Not
Physical Channel CFG~1
CFG(Configure)
Management
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
SC0(0), SC1(1), SC0~0, SC1~1,
SC2(2), SC3(3), SC2~2, SC3~3,
SC4(4), SC5(5), SC4~4, SC5~5,
3GPP R8 SC6(6), SC7(7), SC6~6, SC7~7,
Specifications SC8(8), SC9(9), SC8~8, SC9~9,
Physical Channel SC10(10), SC10~10,
Management SC11(11), SC11~11,
SC12(12), SC12~12,
SC13(13), SC13~13,
SC14(14) SC14~14
Physical Channel BOOLEAN_TRUE( BOOLEAN_TRUE~
Management True) 1
Physical Channel BOOLEAN_TRUE( BOOLEAN_TRUE~
Management True) 1
ACCESS_FIRST(A
3GPP R8 ACCESS_FIRST~0
ccess First),
Specifications ,
Enumeration Type EXPERIENCE_FIR None
Physical Channel EXPERIENCE_FIR
ST(Experience
Management ST~1
First)
BW0(BW0),
BW1(BW1),
3GPP R8 BW2(BW2), BW0~0, BW1~1,
Specifications BW3(BW3), BW2~2, BW3~3,
Physical Channel BW4(BW4), BW4~4, BW5~5,
Management BW5(BW5), BW6~6, BW7~7
BW6(BW6),
BW7(BW7)

Physical Channel
Management NORMAL, NORMAL~0,
Broadcast of EXTENDED EXTENDED~1
system information
Physical Channel
ONE_SIXTH~0,
Management ONE_SIXTH, HALF,
Enumeration Type HALF~1, ONE~2, None
Broadcast of ONE, TWO
TWO~3
system information

rf32(32 radio
frames), rf64(64
Broadcast of
radio frames), rf32~0, rf64~1,
system information Enumeration Type None
rf128(128 radio rf128~2, rf256~3
Paging
frames), rf256(256
radio frames)
FOURT~0,
FOURT, TWOT,
TWOT~1, ONET~2,
ONET, HALFT,
HALFT~3,
QUARTERT,
Broadcast of QUARTERT~4,
ONE_EIGHTT,
system information Enumeration Type ONE_EIGHTT~5, None
ONE_SIXTEENTHT
Paging ONE_SIXTEENTHT
,
~6,
ONE_THIRTY_SEC
ONE_THIRTY_SEC
ONDT
ONDT~7

Physical Channel
Management
Broadcast of
system information
INTER_SUB_FRA
Physical Channel INTER_SUB_FRA
ME(Inter),
Management ME~0,
Enumeration Type INTRA_AND_INTE None
Broadcast of INTRA_AND_INTE
R_SUB_FRAME(Int
system information R_SUB_FRAME~1
er And Intra)
Physical Channel
Management
Interval Type 0~98 N/A RB
Broadcast of
system information
Physical Channel BOOLEAN_FALSE( BOOLEAN_FALSE
Management False), ~0,
Physical Channel
Management
Broadcast of
system information
Physical Channel BOOLEAN_FALSE( BOOLEAN_FALSE
Management False), ~0,
Physical Channel
Management
Broadcast of
system information
False), ~0,
UL 64QAM Enumeration Type None
True) 1
3GPP R8
Specifications
DS1_DELTA_SHIF DS1_DELTA_SHIF
3GPP R8 T(ds1), T~0,
Specifications DS2_DELTA_SHIF DS2_DELTA_SHIF
Physical Channel T(ds2), T~1,
Management DS3_DELTA_SHIF DS3_DELTA_SHIF
T(ds3) T~2
3GPP R8
Specifications
Physical Channel
Management
3GPP R8
Specifications
Physical Channel
Management
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier Character String
PS Inter-RAT Type
Mobility between E-
UTRAN and
CDMA2000
RAN Sharing with
Common Carrier
RAN Sharing with
PS Inter-RAT Type
Mobility between E-
UTRAN and
CDMA2000
RAN Sharing with

Common Carrier
RAN Sharing with
PS Inter-RAT Type
Mobility between E-
UTRAN and
CDMA2000

PS Inter-RAT
Mobility between E- Character String
UTRAN and Type
CDMA2000
PS Inter-RAT
PERMIT_HO_ENU PERMIT_HO_ENU
Mobility between E-
M(Permit Ho), M~0,
UTRAN and Enumeration Type None
FORBID_HO_ENU FORBID_HO_ENU
CDMA2000
M(Forbid Ho) M~1
Inter-RAT ANR
PERMIT_RMV_EN
Automatic UM(Permit ANR PERMIT_RMV_EN
Neighbour Relation Remove), UM~0,
(ANR) FORBID_RMV_EN FORBID_RMV_EN
Inter-RAT ANR UM(Forbid ANR UM~1
Remove)
Automatic
Neighbour Relation
(ANR) Interval Type 0~32 N/A None
Mobility
Management
Automatic BOOLEAN_FALSE( BOOLEAN_FALSE

Neighbour Relation False), ~0,
(ANR) BOOLEAN_TRUE( BOOLEAN_TRUE~
Inter-RAT ANR True) 1
Automatic
Neighbour Relation Character String
(ANR) Type
Inter-RAT ANR
Automatic
(ANR) Type
Inter-RAT ANR
PS Inter-RAT bc0~0, bc1~1,

Mobility between E- bc2~2, bc3~3,
bc0, bc1, bc2, bc3,
UTRAN and bc4~4, bc5~5,
bc4, bc5, bc6, bc7,
CDMA2000 bc6~6, bc7~7,
bc8, bc9, bc10,
Cell Selection and Enumeration Type bc8~8, bc9~9, None
bc11, bc12, bc13,
Reselection / Cell bc10~10, bc11~11,
bc14, bc15, bc16,
Selection and Re- bc12~12, bc13~13,
bc17
selection bc14~14, bc15~15,
Inter-RAT ANR bc16~16, bc17~17
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Cell Selection and Interval Type 0~2047 N/A None
Reselection / Cell
Selection and Re-
selection
Inter-RAT ANR
PS Inter-RAT
Mobility between E-
UTRAN and Interval Type -15~15 N/A dB
CDMA2000
Inter-RAT ANR
3GPP R8
Specifications
NOT_CFG(Not
PS Inter-RAT NOT_CFG~0,
Mobility between E- CFG~1
CFG(Configure)
UTRAN and
CDMA2000
3GPP R8
Specifications
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with
Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with
Common Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with

Dedicated Carrier
RAN Sharing with
Dedicated Carrier
RAN Sharing with

Dedicated Carrier
PS Inter-RAT
UTRAN and Type
CDMA2000
bc0~0, bc1~1,
bc0, bc1, bc2, bc3,
bc4, bc5, bc6, bc7,
bc8, bc9, bc10,
CDMA2000 Enumeration Type bc8~8, bc9~9, None
bc11, bc12, bc13,
Cell Selection and bc10~10, bc11~11,
bc14, bc15, bc16,
Reselection bc12~12, bc13~13,
bc17
Inter-RAT ANR bc14~14, bc15~15,
bc16~16, bc17~17
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000 Interval Type 0~2047 N/A None
Cell Selection and
Reselection
Inter-RAT ANR
3GPP R8
Specifications
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Cell Selection and
Reselection
PS Inter-RAT CDMA2000_HRPD(
Mobility between E- CDMA2000_HRPD) CDMA2000_HRPD
UTRAN and , ~0,
CDMA2000 CDMA2000_1XRTT CDMA2000_1XRTT
Cell Selection and (CDMA2000_1XRT ~1
Reselection T)
PS Inter-RAT
Mobility between E-
UTRAN and
Common Carrier
RAN Sharing with
Dedicated Carrier
PS Inter-RAT
Mobility between E-
UTRAN and
Common Carrier
RAN Sharing with
Dedicated Carrier
PS Inter-RAT
Mobility between E-
UTRAN and
Character String
CDMA2000 0~99 characters N/A None
Type
Cell Selection and
Reselection
Inter-RAT ANR

PS Inter-RAT
UTRAN and Type
CDMA2000
PS Inter-RAT
Mobility between E-
M(Permit Ho), M~0,
CDMA2000
M(Forbid Ho) M~1
Inter-RAT ANR
PERMIT_RMV_EN
Remove)
Automatic
Neighbour Relation
(ANR) Interval Type 0~32 N/A None
Mobility
Management

Automatic
(ANR) Type
Inter-RAT ANR
Automatic
(ANR) Type
Inter-RAT ANR

bc0, bc1, bc2, bc3,
bc4, bc5, bc6, bc7,
CDMA2000 bc6~6, bc7~7,
bc8, bc9, bc10,
Cell Selection and Enumeration Type bc8~8, bc9~9, None
bc11, bc12, bc13,
Reselection / Cell bc10~10, bc11~11,
bc14, bc15, bc16,
Selection and Re- bc12~12, bc13~13,
bc17
selection bc14~14, bc15~15,
Inter-RAT ANR bc16~16, bc17~17
PS Inter-RAT
Mobility between E-
UTRAN and
CDMA2000
Cell Selection and
Reselection / Cell
Selection and
Reselection
Cell Selection and

Reselection
Cell Selection and
Reselection
PS Inter-RAT
UTRAN and Type
GERAN
PS Inter-RAT
UTRAN and Type
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
NOT_CFG(Not
Mobility between E- NOT_CFG~0,
UTRAN and CFG~1
CFG(Configure)
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
SRVCC to GERAN
CS Fallback to
GERAN
GSM_dcs1800, GSM_dcs1800~0,
Service based inter- Enumeration Type None
GSM_pcs1900 GSM_pcs1900~1
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
Inter-RAT Load
Sharing to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load DTM_AVAILABLE~
DTM_AVAILABLE,
Sharing to GERAN 0,
Enumeration Type DTM_NOT_AVAILA None
Service based inter- DTM_NOT_AVAILA
BLE
RAT handover to BLE~1
GERAN
Distance based
inter-RAT handover
to GERAN
PS Inter-RAT
UTRAN and Type
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
False), ~0,
GERAN Enumeration Type None
True) 1
RAT handover to
GERAN

PS Inter-RAT
UTRAN and Type
GERAN
PS Inter-RAT
UTRAN and Type
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PERMIT_RMV_EN
Remove)
M(Permit Ho), M~0,
Inter-RAT ANR Enumeration Type None
M(Forbid Ho) M~1
Mobility
Management
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN

Automatic Neighbor
Character String
Relation (ANR) 0~99 characters N/A None
Type
Inter-RAT ANR
Automatic
(ANR) Type
Inter-RAT ANR
Flash CS Fallback
to GERAN
Flash CS Fallback Character String

to GERAN Type

to GERAN Type

PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN GSM, GPRS, GSM~0, GPRS~1,
Service based inter- EDGE EDGE~2
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Inter-RAT Load
Sharing to GERAN GSM_dcs1800, GSM_dcs1800~0,
Service based inter- GSM_pcs1900 GSM_pcs1900~1
RAT handover to
GERAN
Distance based
inter-RAT handover
to GERAN
Cell Selection and

NOT_CFG(Not
Reselection / Cell NOT_CFG~0,
Selection and Re- CFG~1
CFG(Configure)
selection
Cell Selection and
Reselection
NOT_CFG(Not
Cell Selection and NOT_CFG~0,
Reselection CFG~1
CFG(Configure)
Cell Selection and
Interval Type 0~39 N/A dBm
Reselection
Cell Selection and

Interval Type 0~45 N/A 2dBm
Reselection
Cell Selection and
Reselection
Cell Selection and
Reselection
PS Inter-RAT
Mobility between E-
GERAN
Inter-RAT ANR
Cell Selection and

Reselection / Cell
Selection and Re-
selection

Broadcast of
system information
PS Inter-RAT
Mobility between E-
UTRAN and
GERAN
Broadcast of
system information Interval Type 0~1023 N/A None
Inter-RAT ANR
Cell Selection and

Re-selection
Coverage Based Interval Type 0~503 N/A None
Intra-frequency
Handover
Cell Selection and

Re-selection
Character String
Coverage Based 0~99 characters N/A None
Type
Intra-frequency
Handover
n1(n1), n4(n4),
n8(n8), n12(n12),
n1~0, n4~1, n8~2,
n16(n16), n24(n24),
Cell Selection and n12~3, n16~4,
n32(n32), n48(n48),
Re-selection n24~5, n32~6,
n64(n64), n84(n84),
Coverage Based Enumeration Type n48~7, n64~8, None
n96(n96),
Intra-frequency n84~9, n96~10,
n128(n128),
Handover n128~11, n168~12,
n168(n168),
n252~13, n504~14
n252(n252),
n504(n504)
Coverage Based
Character String
Intra-frequency 3 characters N/A None
Type
Handover
Coverage Based
Character String
Intra-frequency 2~3 characters N/A None
Type
Handover
Coverage Based
Handover
Coverage Based
Handover
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
Coverage Based
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
Intra-frequency
dB0(0dB), dB-3~12, dB-2~13,
Handover
dB1(1dB), dB-1~14, dB0~15,
Mobility Robust Enumeration Type dB
dB2(2dB), dB1~16, dB2~17,
Optimization (MRO)
dB3(3dB), dB3~18, dB4~19,
Intra-LTE Load
dB4(4dB), dB5~20, dB6~21,
Balancing
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
dB0(0dB), dB-3~12, dB-2~13,
Cell Selection and dB1(1dB), dB-1~14, dB0~15,
Enumeration Type dB
Re-selection dB2(2dB), dB1~16, dB2~17,
dB3(3dB), dB3~18, dB4~19,
dB4(4dB), dB5~20, dB6~21,
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
Coverage Based
Intra-frequency
Handover
Automatic PERMIT_HO_ENU PERMIT_HO_ENU
Neighbour Relation M(Permit Ho), M~0,
(ANR) FORBID_HO_ENU FORBID_HO_ENU
Inter-RAT ANR M(Forbid Ho) M~1
Cell Outage
Detection and
Compensation
Automatic
PERMIT_RMV_EN
Neighbour Relation
UM(Permit ANR PERMIT_RMV_EN
(ANR)
Remove), UM~0,
Inter-RAT ANR Enumeration Type None
FORBID_RMV_EN FORBID_RMV_EN
Cell Outage
UM(Forbid ANR UM~1
Detection and
Remove)
Compensation
Automatic
False), ~0,
Neighbour Relation Enumeration Type None
(ANR)
True) 1
Coverage Based
Intra-frequency
Handover Character String
Automatic Type
Neighbour Relation
(ANR)
Coverage Based
Intra-frequency
Automatic Type
Neighbour Relation
(ANR)

3GPP R8
Specifications
Cell Selection and
0~45589,64436~65
Reselection Interval Type N/A None
535
Coverage Based
Inter-frequency
Handover
3GPP R8
Specifications
Cell Selection and NOT_CFG(Not
NOT_CFG~0,
Re-selection Enumeration Type configure), None
CFG~1
Coverage Based CFG(Configure)
Inter-frequency
Handover
3GPP R8
Specifications
Cell Selection and
18000~45589,6443
Reselection Interval Type N/A None
6~65535
Coverage Based
Inter-frequency
Handover
NOT_CFG(Not
Re-selection CFG~1
CFG(Configure)
Cell Selection and
Reselection
Cell Selection and

Re-selection
NOT_CFG(Not
Re-selection CFG~1
CFG(Configure)
0DOT25_ENUM(0.
25),
0DOT25_ENUM~0,
0DOT5_ENUM(0.5)
Cell Selection and 0DOT5_ENUM~1,
Re-selection 0DOT75_ENUM~2,
0DOT75_ENUM(0.
1DOT0_ENUM~3
75),
1DOT0_ENUM(1.0)
0DOT25_ENUM(0.
25),
0DOT25_ENUM~0,
0DOT5_ENUM(0.5)
Cell Selection and 0DOT5_ENUM~1,
Re-selection 0DOT75_ENUM~2,
0DOT75_ENUM(0.
1DOT0_ENUM~3
75),
1DOT0_ENUM(1.0)
3GPP R8
Specifications
Intra-LTE Load
Balancing
Coverage Based
MBW6(1.4M), MBW6~0,
Inter-frequency
MBW15(3M), MBW15~1,
Handover
MBW25(5M), MBW25~2,
Cell Selection and Enumeration Type MHz
MBW50(10M), MBW50~3,
Reselection
MBW75(15M), MBW75~4,
Distance Based
MBW100(20M) MBW100~5
Inter-frequency
Handover
Service Based
Inter-frequency
Handover
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
3GPP R8
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
Specifications
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
Intra-LTE Load
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
Balancing
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
Coverage Based
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
Inter-frequency
dB0(0dB), dB-3~12, dB-2~13,
Handover
dB1(1dB), dB-1~14, dB0~15,
Cell Selection and Enumeration Type dB
dB2(2dB), dB1~16, dB2~17,
Reselection
dB3(3dB), dB3~18, dB4~19,
Distance Based
dB4(4dB), dB5~20, dB6~21,
Inter-frequency
dB5(5dB), dB8~22, dB10~23,
Handover
dB6(6dB), dB12~24, dB14~25,
Service Based
dB8(8dB), dB16~26, dB18~27,
Inter-frequency
dB10(10dB), dB20~28, dB22~29,
Handover
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
Cell Selection and
Reselection
Cell Selection and

Reselection
Cell Selection and
Reselection
NOT_CFG(Not
Reselection CFG~1
CFG(Configure)
Cell Selection and
Reselection
Cell Selection and

BitString00(00), BitString00~0,
Re-selection
Coverage Based Enumeration Type None
Inter-frequency
BitString11(11) BitString11~3
Handover
Cell Selection and
Reselection
False), ~0,
Coverage Based Enumeration Type None
Inter-frequency
True) 1
Handover
Intra-LTE Load
Balancing
Coverage Based
Inter-frequency
Handover EventA3(EventA3), EventA3~0,
Distance Based Enumeration Type EventA4(EventA4), EventA4~1, None
Inter-frequency EventA5(EventA5) EventA5~2
Handover
Service Based
Inter-frequency
Handover
Cell Selection and
Reselection / Cell
Selection and Re-
selection
Cell Selection and
Reselection / Cell
Selection and Re-
selection
Cell Selection and

NOT_CFG(Not
CFG(Configure)
selection
Cell Selection and
Re-selection

Cell Selection and
Reselection
0~45589,64436~65
Coverage Based Interval Type N/A None
535
Inter-frequency
Handover
Cell Selection and

Re-selection
Coverage Based Interval Type 0~503 N/A None
Inter-frequency
Handover
Cell Selection and

Re-selection
Character String
Coverage Based 0~99 characters N/A None
Type
Inter-frequency
Handover
n1(n1), n4(n4),
n8(n8), n12(n12),
n1~0, n4~1, n8~2,
n16(n16), n24(n24),
Cell Selection and n12~3, n16~4,
n32(n32), n48(n48),
Re-selection n24~5, n32~6,
n64(n64), n84(n84),
Coverage Based Enumeration Type n48~7, n64~8, None
n96(n96),
Inter-frequency n84~9, n96~10,
n128(n128),
Handover n128~11, n168~12,
n168(n168),
n252~13, n504~14
n252(n252),
n504(n504)
Coverage Based
Character String
Inter-frequency 3 characters N/A None
Type
Handover
Coverage Based
Character String
Inter-frequency 2~3 characters N/A None
Type
Handover
Coverage Based
Handover
Coverage Based
Handover
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
Intra-LTE Load
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
Balancing
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
Mobility Robust
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
Optimization (MRO)
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
Coverage Based
dB0(0dB), dB-3~12, dB-2~13,
Inter-frequency
dB1(1dB), dB-1~14, dB0~15,
Handover Enumeration Type dB
dB2(2dB), dB1~16, dB2~17,
Distance Based
dB3(3dB), dB3~18, dB4~19,
Inter-frequency
dB4(4dB), dB5~20, dB6~21,
Handover
dB5(5dB), dB8~22, dB10~23,
Service Based
dB6(6dB), dB12~24, dB14~25,
Inter-frequency
dB8(8dB), dB16~26, dB18~27,
Handover
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
dB-24(-24dB), dB-
22(-22dB), dB-20(-
20dB), dB-18(-
18dB), dB-16(-
16dB), dB-14(-
14dB), dB-12(-
12dB), dB-10(- dB-24~0, dB-22~1,
10dB), dB-8(-8dB), dB-20~2, dB-18~3,
dB-6(-6dB), dB-5(- dB-16~4, dB-14~5,
5dB), dB-4(-4dB), dB-12~6, dB-10~7,
dB-3(-3dB), dB-2(- dB-8~8, dB-6~9,
2dB), dB-1(-1dB), dB-5~10, dB-4~11,
dB0(0dB), dB-3~12, dB-2~13,
Cell Selection and dB1(1dB), dB-1~14, dB0~15,
Enumeration Type dB
Re-selection dB2(2dB), dB1~16, dB2~17,
dB3(3dB), dB3~18, dB4~19,
dB4(4dB), dB5~20, dB6~21,
dB5(5dB), dB8~22, dB10~23,
dB6(6dB), dB12~24, dB14~25,
dB8(8dB), dB16~26, dB18~27,
dB10(10dB), dB20~28, dB22~29,
dB12(12dB), dB24~30
dB14(14dB),
dB16(16dB),
dB18(18dB),
dB20(20dB),
dB22(22dB),
dB24(24dB)
Coverage Based
Inter-frequency PERMIT_HO_ENU PERMIT_HO_ENU
Handover M(Permit Ho), M~0,
Automatic FORBID_HO_ENU FORBID_HO_ENU
Neighbour Relation M(Forbid Ho) M~1
(ANR)
PERMIT_RMV_EN
UM(Permit ANR PERMIT_RMV_EN
Automatic
Remove), UM~0,
FORBID_RMV_EN FORBID_RMV_EN
(ANR)
UM(Forbid ANR UM~1
Remove)
Intra-LTE Load
Balancing
Coverage Based
Inter-frequency
Handover
Selection and
Reselection Interval Type 0~32 N/A None
Distance Based
Inter-frequency
Handover
Service Based
Inter-frequency
Handover
Automatic
False), ~0,
(ANR)
True) 1
Coverage Based
Inter-frequency
Automatic Type
Neighbour Relation
(ANR)
Coverage Based
Inter-frequency
Automatic Type
Neighbour Relation
(ANR)
Coverage Based
Intra-frequency
Coverage Based Type
Inter-frequency
Handover
Coverage Based
Intra-frequency
Coverage Based Type
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover 0~45589,64436~65
Coverage Based 535
Inter-frequency
Handover
Coverage Based
Intra-frequency
NOT_CFG(Not
Handover NOT_CFG~0,
Coverage Based CFG~1
CFG(Configure)
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover 18000~45589,6443
Coverage Based 6~65535
Inter-frequency
Handover
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Cell Selection and
Reselection
Coverage Based
Intra-frequency
Handover
Coverage Based
Inter-frequency
Handover
Coverage Based
Intra-frequency
Coverage Based Type
Inter-frequency
Handover
Cell Selection and

Reselection / Cell
Selection and Re-
selection
Cell Selection and
Reselection
Cell Selection and

Reselection / Cell Character String
Selection and Re- Type
selection
Cell Selection and

selection
Cell Selection and
NOT_CFG(Not
CFG(Configure)
selection
Cell Selection and

Reselection / Cell
Selection and Re-
selection

PS Inter-RAT
UTRAN and Type
UTRAN
PS Inter-RAT
UTRAN and Type
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
M(Permit Ho), M~0,
UTRAN
M(Forbid Ho) M~1
Inter-RAT ANR
PERMIT_RMV_EN
Remove)
Mobility
Management

PS Inter-RAT
UTRAN and Type
UTRAN
PS Inter-RAT
UTRAN and Type
UTRAN
Flash CS Fallback
to UTRAN
Flash CS Fallback
to UTRAN

to UTRAN Type

to UTRAN Type
Cell Selection and

Reselection / Cell
Selection and Re-
selection
Cell Selection and
Reselection
Cell Selection and

selection
Cell Selection and
selection
Cell Selection and

NOT_CFG(Not
CFG(Configure)
selection
Cell Selection and
Reselection / Cell
Selection and Re-
selection

Broadcast of
System Information
PS Inter-RAT
Mobility between E- Interval Type 0~16383 N/A None
UTRAN and
UTRAN
Inter-RAT ANR
PS Inter-RAT
Mobility between E-
UTRAN and R99, HSDPA, R99~0, HSDPA~1,
UTRAN HSUPA, HSPA HSUPA~2, HSPA~3
Cell Selection and
Reselection
PS Inter-RAT
Mobility between E-
UTRAN_FDD, UTRAN_FDD~0,
UTRAN_TDD UTRAN_TDD~1
UTRAN
Inter-RAT ANR
PS Inter-RAT
Mobility between E-
NOT_CFG(Not
UTRAN and NOT_CFG~0,
UTRAN CFG~1
CFG(Configure)
Cell Selection and
Reselection
Broadcast of
System Information
PS Inter-RAT
Mobility between E- Interval Type 0~16383 N/A None
UTRAN and
UTRAN
Inter-RAT ANR
Cell Selection and

NOT_CFG(Not
CFG(Configure)
selection
Cell Selection and
Reselection
Broadcast of
System Information
Cell Selection and

Reselection
PS Inter-RAT
Mobility between E-
UTRAN
Inter-RAT ANR
Cell Selection and

Reselection / Cell
Interval Type -24~0 N/A dB
Selection and Re-
selection
Cell Selection and
Reselection / Cell
Selection and Re-
selection
Cell Selection and
Reselection
Cell Selection and
Reselection
Cell Selection and
Reselection / Cell
Selection and Re-
selection
Cell Selection and
Reselection / Cell
Selection and Re-
selection
PS Inter-RAT LOW_PRIORITY(L
LOW_PRIORITY~1
Mobility between E- ow Priority),
UTRAN and HIGH_PRIORITY(H
HIGH_PRIORITY~2
UTRAN igh Priority)
CS Fallback to
LOW_PRIORITY(L
UTRAN LOW_PRIORITY~1
ow Priority),
E-UTRAN to Enumeration Type , None
HIGH_PRIORITY(H
UTRAN CS/PS HIGH_PRIORITY~2
igh Priority)
Steering
PS Inter-RAT
UTRAN and Type
UTRAN
PS Inter-RAT
UTRAN and Type
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E- UTRAN_FDD, UTRAN_FDD~0,
UTRAN and UTRAN_TDD UTRAN_TDD~1
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
UTRAN
Distance based
inter-RAT handover
to UTRAN
PS Inter-RAT
NOT_CFG(Not
UTRAN and CFG~1
CFG(Configure)
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
NOT_CFG(Not
UTRAN and CFG~1
CFG(Configure)
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
UTRAN
Distance based
inter-RAT handover
to UTRAN
PS Inter-RAT
Mobility between E-
UTRAN and
UTRAN
Inter-RAT Load
Sharing to UTRAN
RAT handover to
UTRAN
Distance based
inter-RAT handover
to UTRAN
PS Inter-RAT
UTRAN and Type
UTRAN
PS Inter-RAT BOOLEAN_FALSE( BOOLEAN_FALSE

Mobility between E- False), ~0,
UTRAN and BOOLEAN_TRUE( BOOLEAN_TRUE~
UTRAN True) 1
Automatic
Neighbour Relation Interval Type 0~100 N/A %
(ANR)
Automatic
Neighbour Relation Interval Type 0~100 N/A %
(ANR)
Automatic
Neighbour Relation Interval Type 1~10000 N/A None
(ANR)
Automatic
Neighbour Relation Interval Type 1~10080 N/A min
(ANR)
Automatic r1(1), r2(2), r4(4),

r1~0, r2~1, r4~2,
Neighbour Relation r8(8), r16(16),
(ANR) r32(32), r64(64),
r64~6, Infinity~7
Inter-RAT ANR Infinity(Infinity)
120ms~0,
240ms~1,
480ms~2,
120ms, 240ms, 640ms~3,
Automatic 480ms, 640ms, 1024ms~4,
Neighbour Relation 1024ms, 2048ms, 2048ms~5,
(ANR) 5120ms, 10240ms, 5120ms~6,
Inter-RAT ANR 1min, 6min, 12min, 10240ms~7,
12min~10,
30min~11,
60min~12
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
(ANR)
Inter-RAT ANR Interval Type 1~200 N/A None
Automatic
(ANR)
Inter-RAT ANR Interval Type 1~10000 N/A None
Automatic FREE(FREE),
FREE~0,
Neighbour Relation Enumeration Type CONTROLLED(CO None
CONTROLLED~1
(ANR) NTROLLED)
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
Neighbour Relation Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
(ANR)
Automatic
Neighbour Relation Compound Type 00:00:00~23:59:59 N/A None
(ANR)
Automatic
Neighbour Relation Compound Type 00:00:00~23:59:59 N/A None
(ANR)
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
Automatic
Neighbour Relation
(ANR)
Inter-RAT ANR
True) 1
2000-01-
01T00:00:00.000-
Broadcast of
Compound Type 00:00~2099-12- N/A None
system information
31T23:59:59.000-
00:00
Broadcast of
Interval Type 1~365 N/A day
system information










witch(InterFreqCov
erHoSwitch),
UtranCsfbSwitch(Ut
ranCsfbSwitch),
GeranCsfbSwitch(G
IntraFreqCoverHoS
eranCsfbSwitch),
witch~0,
Cdma1xRttCsfbSwit
Coverage Based InterFreqCoverHoS
ch(Cdma20001xRtt
Intra-frequency witch~1,
CsfbSwitch),
Handover UtranCsfbSwitch~2,
UtranServiceHoSwit
Coverage Based GeranCsfbSwitch~3
ch(UtranServiceHo
Inter-frequency ,
Switch),
Handover Cdma1xRttCsfbSwit
GeranServiceHoSw
Service based inter- ch~4,
itch(GeranServiceH
RAT handover to UtranServiceHoSwit
oSwitch),
UTRAN ch~5,
CdmaHrpdServiceH
Service based inter- GeranServiceHoSw
oSwitch(Cdma2000
RAT handover to itch~6,
HrpdServiceHoSwit
GERAN CdmaHrpdServiceH
ch),
Service Based Bit Field Type oSwitch~7, None
Cdma1xRttService
Inter-frequency Cdma1xRttService
HoSwitch(Cdma200
Handover HoSwitch~8,
01xRttServiceHoSw
CS Fallback to UlQualityInterRATH
itch),
UTRAN oSwitch~9,
UlQualityInterRATH
CS Fallback to InterPlmnHoSwitch
oSwitch(UlQualityIn
GERAN ~10,
terRATHoSwitch),
CS Fallback to UtranFlashCsfbSwit
InterPlmnHoSwitch(
CDMA2000 1xRTT ch~11,
InterPlmnHoSwitch)
Flash CS Fallback GeranFlashCsfbSwi
,
to UTRAN tch~12,
UtranFlashCsfbSwit
Flash CS Fallback ServiceBasedInterF
ch(UtranFlashCsfb
to GERAN reqHoSwitch~13,
Switch),
UlQualityInterFreqH
GeranFlashCsfbSwi
oSwitch~14
tch(GeranFlashCsfb
Switch),
ServiceBasedInterF
reqHoSwitch(Servic
eBasedInterFreqHo
GeranVoipCapSwitc
h(GeranVoipCapSw
EutranVoipCapSwit
itch),
ch~0,
Cdma1xRttVoipCap
UtranVoipCapSwitc
Switch(Cdma1xRttV
h~1,
oipCapSwitch),
GeranVoipCapSwitc
UtranPsHoSwitch(U
h~2,
tranPsHoSwitch),
Cdma1xRttVoipCap
GeranPsHoSwitch(
Switch~3,
GeranPsHoSwitch),
UtranPsHoSwitch~
CdmaHrpdNonOtpi
4,
misedHoSwitch(Cd
PS Inter-RAT GeranPsHoSwitch~
maHrpdNonOtpimis
Mobility between E- 5,
edHoSwitch),
UTRAN and CdmaHrpdNonOtpi
CdmaHrpdOptimise
UTRAN misedHoSwitch~6,
dHoSwitch(CdmaHr
PS Inter-RAT CdmaHrpdOptimise
pdOptimisedHoSwit
Mobility between E- dHoSwitch~7,
ch),
UTRAN and GeranNaccSwitch~
Bit Field Type GeranNaccSwitch( None
GERAN 8,
GeranNaccSwitch),
PS Inter-RAT GeranCcoSwitch~9,
GeranCcoSwitch(G
Mobility between E- UtranSrvccSwitch~
eranCcoSwitch),
UTRAN and 10,
UtranSrvccSwitch(U
CDMA2000 GeranSrvccSwitch~
tranSrvccSwitch),
SRVCC to UTRAN 11,
GeranSrvccSwitch(
SRVCC to GERAN Cdma1xRttSrvccSw
GeranSrvccSwitch),
itch~12,
Cdma1xRttSrvccSw
UtranRedirectSwitc
itch(Cdma1xRttSrvc
h~13,
cSwitch),
GeranRedirectSwitc
UtranRedirectSwitc
h~14,
h(UtranRedirectSwit
CdmaHrpdRedirect
ch),
Switch~15,
GeranRedirectSwitc
Cdma1xRttRedirect
h(GeranRedirectSw
Switch~16,
itch),
BlindHoSwitch~17
CdmaHrpdRedirect
Switch(CdmaHrpdR
Downlink Static DlIcicSwitch_OFF_ DlIcicSwitch_OFF_
Inter-Cell ENUM, ENUM~0,
Interference DlIcicDynamicSwitc DlIcicDynamicSwitc
Coordination h_ON_ENUM, h_ON_ENUM~1,
Downlink Dynamic DlIcicStaticSwitch_ DlIcicStaticSwitch_
Inter-Cell ON_ENUM, ON_ENUM~2,
Interference DlIcicReuse3Switch DlIcicReuse3Switch
Coordination _ON_ENUM _ON_ENUM~3
IntraRatEventAnrS IntraRatEventAnrS
witch, witch~0,
IntraRatFastAnrSwit IntraRatFastAnrSwit
ch, ch~1,
IntraRatAnrAutoDel IntraRatAnrAutoDel
Switch, Switch~2,
UtranEventAnrSwitc UtranEventAnrSwitc
h, h~3,
GeranEventAnrSwit GeranEventAnrSwit
ch, ch~4,
Automatic UtranFastAnrSwitch UtranFastAnrSwitch
Neighbour Relation , ~5,
Bit Field Type None
(ANR) GeranFastAnrSwitc GeranFastAnrSwitc
Inter-RAT ANR h, h~6,
CdmaFastAnrSwitc CdmaFastAnrSwitc
h, h~7,
UtranAutoNrtDelete UtranAutoNrtDelete
Switch, Switch~8,
GeranAutoNrtDelet GeranAutoNrtDelet
eSwitch, eSwitch~9,
CdmaAutoNrtDelete CdmaAutoNrtDelete
Switch, Switch~10,
ExtendIntraRatAnrS ExtendIntraRatAnrS
witch witch~11
PS Inter-RAT
Mobility between E- LoadBasedSwitch~
LoadBasedSwitch,
UTRAand UTRAN 0,
GeranFlashRedirect
PS Inter-RAT GeranFlashRedirect
Bit Field Type Switch, None
Mobility between E- Switch~1,
UranFlashRedirect
UTRAand GERAN UranFlashRedirect
Switch
Cell Selection and Switch~2
Re-selection
IntraFreqMroSwitch
(IntraFreqMroAlgoS IntraFreqMroSwitch
witch), ~0,
Mobility Robust InterFreqMroSwitch InterFreqMroSwitch
Bit Field Type None
Optimization (MRO) (InterFreqMroAlgoS ~1,
witch), UtranMroSwitch~2,
UtranMroSwitch, GeranMroSwitch~3
GeranMroSwitch
3GPP R8
Specifications
Bit Field Type TpeAlgoSwitch TpeAlgoSwitch~0 None
TCP Proxy
Enhancer (TPE)

Cell Interference
Coordination UlIcicIntraSwitch(U
Uplink Dynamic Bit Field Type plink Intra-eNB ICIC UlIcicIntraSwitch~0 None
Inter-Cell switch)
Interference
Coordination
Cell Interference
OFF(Off),
Coordination
STATIC(Static), OFF~0, STATIC~1,
Uplink Dynamic Enumeration Type None
DYNAMIC(Dynamic DYNAMIC~2
Inter-Cell
)
Interference
Coordination
LoCation OtdoaSwitch(OTDO
Bit Field Type OtdoaSwitch~0 None
Services(LCS) A switch)
Enhanced UlUuFlowCtrlSwitch
UlUuFlowCtrlSwitch
Transmission QoS Bit Field Type (UU flow control None
~0
Management switch)
PCI Collision
Detection & Self- Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Optimization
SymbolShutdownS
Symbol Power SymbolShutdownS
Bit Field Type witch(Symbol None
Saving witch~0
shutdown switch)
UTRAN_RIM_SWIT
Flash CS Fallback CH(UTRAN RIM UTRAN_RIM_SWIT
to UTRAN Switch), CH~0,
Bit Field Type None
Flash CS Fallback GERAN_RIM_SWI GERAN_RIM_SWI
to GERAN TCH(GERAN RIM TCH~1
Switch)
NBSLTEPLMNRou
Automatic ndSwitch(NBSLTEP NBSLTEPLMNRou
Neighbour Relation LMNRoundSwitch), ndSwitch~0,
Bit Field Type None
(ANR) NBSLTERANSharin NBSLTERANSharin
Inter-RAT ANR gSwitch(NBSLTER gSwitch~1
ANSharingSwitch)
UtranFreqLayerMea
sSwitch(UtranFreqL UtranFreqLayerMea
E-UTRAN to
ayerMeasSwitch), sSwitch~0,
UTRAN CS/PS Bit Field Type None
UtranFreqLayerBlin UtranFreqLayerBlin
Steering
dSwitch(UtranFreqL dSwitch~1
ayerBlindSwitch)

RAN Sharing with

Common Carrier
SHARING(Sharing),
RAN Sharing with SHARING~0,
Enumeration Type DEDICATE(Dedicat None
Common Carrier DEDICATE~1
e)
RAN Sharing with

Common Carrier
RAN Sharing with
Common Carrier
RAN Sharing with

Common Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Common Carrier
RAN Sharing with

Common Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Common Carrier
RAN Sharing with

Common Carrier
RAN Sharing with

Common Carrier
RAN Sharing with
Common Carrier
RAN Sharing with

Common Carrier
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)
Mobility Robust
Optimization(MRO)

None Interval Type 0~50000 N/A ms
Radio Bearer
Management
Radio Bearer
Interval Type 0~4294967295 N/A bit/s
Management
Radio Bearer
Management
0~261120,275943~
None Interval Type N/A Ts
307200
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
TCP Proxy
Enhancer(TPE)
Self-configuration Interval Type 0~195 N/A None

SGW~0,
Self-configuration Enumeration Type SGW, X2eNodeB None
X2eNodeB~1
Self-configuration Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None

Self-configuration Enumeration Type IP(IP) IP~1 None

BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
E1_COVERBOARD
E1_COVERBOARD
(E1 Cover Board),
~3,
Self-configuration Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
k Board),
ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)

PPP(PPP Link),
MPGRP(Multi-link
PPP~6, MPGRP~8,
PPP Group),
ETH~9,
Self-configuration Enumeration Type ETH(Ethernet Port), None
ETHTRK~10,
ETHTRK(Ethernet
TUNNEL~15
Trunk),
TUNNEL(Tunnel)
Self-configuration Character String

Ipsec Type
Self-configuration
Ipsec
Ipsec Type
Self-configuration
Enumeration Type X2(X2), S1(S1) X2~0, S1~1 None
Ipsec
Self-configuration IKE_V1(IKE V1), IKE_V1~1,

Ipsec IKE_V2(IKE V2) IKE_V2~2
MAIN(Main Mode),
Self-configuration MAIN~2,
Enumeration Type AGGRESSIVE(Agg None
Ipsec AGGRESSIVE~4
ressive Mode)
Self-configuration
Password Type 0~127 characters N/A None
Ipsec
DISABLE(Disable),
Self-configuration DISABLE~0,
Enumeration Type PERIODIC(Periodic None
Ipsec PERIODIC~2
)
Self-configuration
Ipsec
Self-configuration
Ipsec
Self-configuration
Ipsec
DISABLE(Disable),
PFS_GROUP1(768
-bit Diffie-Hellman DISABLE~0,
Self-configuration
Enumeration Type Group), PFS_GROUP1~1, None
Ipsec
PFS_GROUP2(102 PFS_GROUP2~2
4-bit Diffie-Hellman
Group)
GLOBAL(Global
Self-configuration Configuration), GLOBAL~0,
Ipsec LOCAL(Local LOCAL~1
Configuration)
Self-configuration
Ipsec
Self-configuration 0,1843200~429496
Interval Type N/A KB
Ipsec 7295
Self-configuration
Ipsec
IPv4/IPv6 Dual
Character String
Stack 1~15 characters N/A None
Type
Self-configuration
IPv4/IPv6 Dual
Stack IP Address Type Valid IP address N/A None
Self-configuration
IPv4/IPv6 Dual
Stack DISABLE(Disable), DISABLE~0,
Self-configuration ENABLE(Enable) ENABLE~1
IPsec for IPv6
IPv4/IPv6 Dual
Stack Character String
Self-configuration Type
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack Interval Type 1024~65535 N/A None
Self-configuration
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
Release_R8(Releas
e 8),
IPv4/IPv6 Dual Release_R8~0,
Release_R9(Releas
Stack Enumeration Type Release_R9~1, None
e 9),
Self-configuration Release_R10~2
Release_R10(Rele
ase 10)

Self-configuration IP Address Type Valid IP address N/A None
Self-configuration DISABLE(Disable), DISABLE~0,

Ipsec ENABLE(Enable) ENABLE~1
Ipsec Type

Ipsec Type

Ipsec Type

Ipsec Type
Character String
Self-configuration 0~20 characters N/A None
Type

Release_R8(Releas
e 8),
Release_R8~0,
Release_R9(Releas
Self-configuration Enumeration Type Release_R9~1, None
e 9),
Release_R10~2
Release_R10(Rele
ase 10)
Character String
Type

Self-configuration
IP Address Type Valid IP address N/A None
Ipsec
Self-configuration Enumeration Type None
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
Stack Enumeration Type None
Self-configuration
IPv4/IPv6 Dual
Self-configuration
Character String
Type

Self-configuration
Ipsec

Self-configuration
Ipsec

Self-configuration Interval Type 10~59999 N/A ms


ALDER32(ALDER3 ALDER32~0,
2), CRC32(CRC32) CRC32~1
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Stack Interval Type 1000~60000 N/A ms
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
2), CRC32(CRC32) CRC32~1
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration


Ipsec Type

Ipsec Type

Ipsec Type

Ipsec Type

Ipsec Type

Ipsec Type

Ipsec Type

Ipsec Type
Character String
Type

IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
Character String
Type

Self-configuration
Ipsec
Character String
Type

Ipsec Type

Character String
Type


Self-configuration
Ipsec

Ipsec Type
Ipsec Type



Ipsec Type
Ipsec Type



2), CRC32(CRC32) CRC32~1


Self-configuration
Ipsec

Self-configuration
Ipsec


Self-configuration
Ipsec

Self-configuration
Ipsec

Self-configuration
Ipsec

Self-configuration
Ipsec
Character String
Self-configuration 0~0,3~3 characters N/A None
Type
Character String
Self-configuration 0~0,2~3 characters N/A None
Type
Character String
Type
Release_R8(Releas
e 8),
Release_R8~0,
Release_R9(Releas
Self-configuration Enumeration Type Release_R9~1, None
e 9),
Release_R10~2
Release_R10(Rele
ase 10)
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
2), CRC32(CRC32) CRC32~1
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Stack
Self-configuration
IPsec for IPv6
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Character String
Stack 0~0,3~3 characters N/A None
Type
Self-configuration
IPv4/IPv6 Dual
Character String
Stack 0~0,2~3 characters N/A None
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
IPv4/IPv6 Dual
Character String
Type
Self-configuration
IPv4/IPv6 Dual
Self-configuration
Release_R8(Releas
e 8),
IPv4/IPv6 Dual Release_R8~0,
Release_R9(Releas
Stack Enumeration Type Release_R9~1, None
e 9),
Self-configuration Release_R10~2
Release_R10(Rele
ase 10)
Public Key Character String

Infrastructure(PKI) Type

SHA1(SHA1), SHA1~0,
SHA256(SHA256) SHA256~2
DEFAULT_MODE(
DEFAULT_MODE), DEFAULT_MODE~
CFG_UPD_SIP(CF 0,
None Enumeration Type G_UPD_SIP), CFG_UPD_SIP~1, None
CFG_INIT_UPD_A CFG_INIT_UPD_A
DDR(CFG_INIT_U DDR~2
PD_ADDR)
Character String
Type

Public Key ESN(ESN), ESN~0, MAC~1,
Infrastructure(PKI) MAC(MAC), IP(IP) IP~2


0~0,2~2 characters N/A None



DATA_ENCIPHER
MENT(DATA_ENCI
PHERMENT), DATA_ENCIPHER
DIGITAL_SIGNATU MENT~0,
RE(DIGITAL_SIGN DIGITAL_SIGNATU
Public Key ATURE), RE~1,
Bit Field Type None
Infrastructure(PKI) KEY_AGREEMENT KEY_AGREEMENT
(KEY_AGREEMEN ~2,
T), KEY_ENCIPHERM
KEY_ENCIPHERM ENT~3
ENT(KEY_ENCIPH
ERMENT)
SHA1(SHA1),
Public Key SHA1~0, MD5~1,
Enumeration Type MD5(MD5), None
Infrastructure(PKI) SHA256~2
SHA256(SHA256)
KEYSIZE1024(KEY
Public Key SIZE1024), KEYSIZE1024~0,
Infrastructure(PKI) KEYSIZE2048(KEY KEYSIZE2048~1
SIZE2048)
Public Key
Infrastructure(PKI)





Public Key
Enumeration Type IKE(IKE), SSL(SSL) IKE~0, SSL~1 None
Infrastructure(PKI)






NORMALLY(NORM
ALLY),
NORMALLY~0,
Public Key ABNORMALITY(AB
Enumeration Type ABNORMALITY~1, None
Infrastructure(PKI) NORMALITY),
FILENOTEXIST~2
FILENOTEXIST(Fil
e not exist)
Public Key
Enumeration Type IKE(IKE), SSL(SSL) IKE~0, SSL~1 None
Infrastructure(PKI)




NORMALLY(NORM
ALLY),
NORMALLY~0,
FILENOTEXIST~2
FILENOTEXIST(Fil
e not exist)






NORMALLY(NORM
ALLY),
NORMALLY~0,
FILENOTEXIST~2
FILENOTEXIST(Fil
e not exist)

NORMAL(Normal),
CERTLOSS(Certific
ate Loss),
NORMAL~0,
CERTDAMAGE(Ce
CERTLOSS~1,
Public Key rtificate Damage),
Enumeration Type CERTDAMAGE~2, None
Infrastructure(PKI) UNKNOWFORMAT
UNKNOWFORMAT
(Unknow File
~3, FAILED~4
Format),
FAILED(Other failed
Reason)



Public Key
Infrastructure(PKI)

Public Key
Infrastructure(PKI)
Public Key
Infrastructure(PKI)

Public Key DISABLE(Disable), DISABLE~0,

Infrastructure(PKI) ENABLE(Enable) ENABLE~1
Public Key
Infrastructure(PKI)
Public Key
Infrastructure(PKI)
Public Key FTP(FTP),
Enumeration Type FTP~0, LDAP~1 None
Infrastructure(PKI) LDAP(LDAP)

Public Key DISABLE(Disable), DISABLE~0,

Infrastructure(PKI) ENABLE(Enable) ENABLE~1
Public Key
Infrastructure(PKI)
Public Key
Infrastructure(PKI)
Public Key PROXY(PROXY),
Enumeration Type PROXY~0, CMP~1 None
Infrastructure(PKI) CMP(CMP)
NOVERIFY(No
Verifying),
ALARM(Send an
NOVERIFY~0,
Public Key Alarm If Verifying
Enumeration Type ALARM~1, None
Infrastructure(PKI) CRL Failed),
DISCONNECT~2
DISCONNECT(Disc
onnect If Verifying
CRL Failed)
IPsec
Access Control List Interval Type 3000~4999 N/A None
(ACL)
IPsec
Character String
Access Control List 0~127 characters N/A None
Type
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Access Control List Type
(ACL)
IPsec
(ACL)
IPsec
(ACL)
IPsec
DENY(Deny), DENY~0,
Access Control List Enumeration Type None
PERMIT(Permit) PERMIT~1
(ACL)
IP(IP),
IPsec ICMP(ICMP), IP~0, ICMP~1,
Access Control List Enumeration Type TCP(TCP), TCP~6, UDP~17, None
(ACL) UDP(UDP), SCTP~132
SCTP(SCTP)
IPsec
Access Control List IP Address Type Valid IP address N/A None
(ACL)
IPsec
Wildcard Mask Valid wildcard of the
Access Control List N/A None
Type IP address
(ACL)
IPsec
Access Control List Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None
(ACL)
OP_LT(Less or
Equal),
OP_GT(Greater or OP_LT~1,
IPsec Equal), OP_GT~2,
Access Control List Enumeration Type OP_EQ(Equivalent) OP_EQ~3, None
(ACL) , OP_NEQ(Not OP_NEQ~4,
Equivalent), OP_RANGE~5
OP_RANGE(Range
)
IPsec
(ACL)
IPsec
(ACL)
IPsec
Access Control List IP Address Type Valid IP address N/A None
(ACL)
IPsec
Wildcard Mask Valid wildcard of the
Access Control List N/A None
Type IP address
(ACL)
IPsec
(ACL)
OP_LT(Less or
Equal),
IPsec Equal), OP_GT~2,
Access Control List Enumeration Type OP_EQ(Equivalent) OP_EQ~3, None
(ACL) , OP_NEQ(Not OP_NEQ~4,
OP_RANGE(Range
)
IPsec
(ACL)
IPsec
(ACL)
IPsec
(ACL)
IPsec
(ACL)
IPsec
(ACL)
OP_EQ(Equivalent)
IPsec
, OP_EQ~0,
Access Control List Enumeration Type None
OP_RANGE(Range OP_RANGE~1
(ACL)
)
IPsec
(ACL)
IPsec
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack DENY(Deny), DENY~0,
Access Control List PERMIT(Permit) PERMIT~1
(ACL)
IP6(IPv6),
IPv4/IPv6 Dual IP6~0, TCP~6,
TCP(TCP),
Stack UDP~17,
Enumeration Type UDP(UDP), None
Access Control List ICMP6~58,
ICMP6(ICMP6),
(ACL) SCTP~132
SCTP(SCTP)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None
Access Control List
(ACL)
OP_LT(Less or
Equal),
IPv4/IPv6 Dual
Equal), OP_GT~2,
Stack
Enumeration Type OP_EQ(Equivalent) OP_EQ~3, None
Access Control List
, OP_NEQ(Not OP_NEQ~4,
(ACL)
OP_RANGE(Range
)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
OP_LT(Less or
Equal),
IPv4/IPv6 Dual
Equal), OP_GT~2,
Stack
Enumeration Type OP_EQ(Equivalent) OP_EQ~3, None
Access Control List
, OP_NEQ(Not OP_NEQ~4,
(ACL)
OP_RANGE(Range
)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
IPv4/IPv6 Dual
Stack
Access Control List
(ACL)
Bidirectional
Forwarding Interval Type 0~7 N/A None
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Forwarding IP Address Type Valid IP address N/A None
Detection
Bidirectional
Forwarding IP Address Type Valid IP address N/A None
Detection
SINGLE_HOP(Singl
Bidirectional
e Hop), SINGLE_HOP~0,
Forwarding Enumeration Type None
MULTI_HOP(Multipl MULTI_HOP~1
Detection
e Hops)
Bidirectional
Forwarding Interval Type 10~1000 N/A ms
Detection
Bidirectional
Detection
Bidirectional
Detection
MAINTENANCE(M
Bidirectional
aintenance), MAINTENANCE~0,
Forwarding Enumeration Type None
RELIABILITY(Relia RELIABILITY~1
Detection
bility)
Bidirectional
Detection
Bidirectional
Forwarding Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None
Detection
ADMINDOWN(Adm
Bidirectional ADMINDOWN~0,
in Down),
Forwarding Enumeration Type DOWN~1, INIT~2, None
DOWN(Down),
Detection UP~3
INIT(Init), UP(Up)
Bidirectional ASYNCHRONOUS
ASYNCHRONOUS
Forwarding Enumeration Type _MODE(Asynchron None
_MODE~2
Detection ous Mode)
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
Bidirectional
Detection
NO_DIAGNOSTIC(
No Diagnostic),
CTRL_DECT_TIME
_EXPIRED(Control
Detection Time
Expired),
ECHO_FUNC_FAIL
ED(Echo Function
Failed), NO_DIAGNOSTIC~
NEIGHBOR_SIG_S 0,
ESSION_DOWN(N CTRL_DECT_TIME
eighbor Signaled _EXPIRED~1,
Session Down), ECHO_FUNC_FAIL
FORDWARDING_P ED~2,
LANE_RESET(For NEIGHBOR_SIG_S
warding Plane ESSION_DOWN~3,
Bidirectional Reset), FORDWARDING_P
Forwarding Enumeration Type PATH_DOWN(Path LANE_RESET~4, None
Detection Down), PATH_DOWN~5,
CONCATENATED_ CONCATENATED_
PATH_DOWN(Conc PATH_DOWN~6,
atenated Path ADMIN_DOWN~7,
Down), REVERSE_CONCA
ADMIN_DOWN(Ad TENTATED_PATH_
ministratively DOWN~8,
Down), PEER_ADMIN_DO
REVERSE_CONCA WN~9
TENTATED_PATH_
DOWN(Reverse
Concatenated Path
Down),
PEER_ADMIN_DO
WN(Peer
Administratively
Down)
Bidirectional DRAFT4(DRAFT4),
DRAFT4~0,
Forwarding Enumeration Type STANDARD(STAN None
STANDARD~1
Detection DARD)
Public Key DEFAULT(Default), DEFAULT~0,

Infrastructure(PKI) SPECIFIC(Specific) SPECIFIC~1
Public Key
Infrastructure(PKI)
Public Key
Infrastructure(PKI)
Public Key
Infrastructure(PKI)
Ethernet
Character String
OAM(IEEE 1~43 characters N/A None
Type
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
OAM(IEEE Interval Type 1~8191 N/A None
802.1ag)
Ethernet
OAM(IEEE IP Address Type Valid IP address N/A None
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
OAM(IEEE Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
10ms(10ms),
Ethernet 100ms(100ms), 10ms~2, 100ms~3,
OAM(IEEE Enumeration Type 1s(1s), 10s(10s), 1s~4, 10s~5, None
802.1ag) 1min(1min), 1min~6, 10min~7
10min(10min)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
OAM(IEEE Interval Type None N/A None
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
BASE_BOARD(Bas
Ethernet e Board), BASE_BOARD~0,
OAM(IEEE Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
802.1ag) D(Ethernet Cover D~5
Board)
Ethernet ETH(Ethernet Port),

OAM(IEEE Enumeration Type ETHTRK(Ethernet ETH~3, ETHTRK~4 None
802.1ag) Trunk)
Ethernet
802.1ag)
Ethernet
OAM(IEEE Enumeration Type None
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
Character String
Type
802.1ag)
Ethernet
802.1ag)
Ethernet
OAM(IEEE Compound Type 14 characters N/A None
802.1ag)
Ethernet
NORMAL(Normal), NORMAL~1,
FAULT(Fault) FAULT~2
802.1ag)
Ethernet
OAM(IEEE Compound Type 14 characters N/A None
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
802.1ag)
Ethernet
OAM(IEEE IP Address Type Valid IP address N/A None
802.1ag)
TCP(TCP Protocol),
Integrated Firewall Enumeration Type TCP~6, UDP~17 None
UDP(UDP Protocol)
22(22), 23(23), 22~22, 23~23,

67(67), 68(68), 67~67, 68~68,
80(80), 319(319), 80~80, 319~319,
320(320), 443(443), 320~320, 443~443,
500(500), 500~500,
1110(1110), 1110~1110,
1120(1120), 1120~1120,
2700(2700), 2700~2700,
3784(3784), 3784~3784,
4443(4443), 4443~4443,
Integrated Firewall Enumeration Type None
4500(4500), 4500~4500,
4784(4784), 4784~4784,
6000(6000), 6000~6000,
6001(6001), 6001~6001,
6006(6006), 6006~6006,
6007(6007), 6007~6007,
17185(17185), 17185~17185,
30023(30023), 30023~30023,
33003(33003), 33003~33003,
45300(45300) 45300~45300

BASE_BOARD(Bas
e Board), BASE_BOARD~0,
E1_COVERBOARD E1_COVERBOARD
None Enumeration Type (E1 Cover Board), ~3, None
ETH_COVERBOAR ETH_COVERBOAR
D(Ethernet Cover D~5
Board)
PPP(PPP Link),
MPGRP(Multi-link
PPP Group), PPP~0, MPGRP~2,
ETH(Ethernet Port), ETH~3,
ETHTRK(Ethernet ETHTRK~4,
Trunk), LOOPINT~6
LOOPINT(Loopbac
k Interface)
None Subnet Mask Type Valid Mask address N/A None

IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IP6_DAD_OK(Valid
IP6_DAD_OK~1,
),
IP6_DAD_TENTATI
IP6_DAD_TENTATI
VE~2,
IPv4/IPv6 Dual VE(Tentative),
Enumeration Type IP6_DAD_DUPLIC None
Stack IP6_DAD_DUPLIC
ATED~4,
ATED(Duplicate),
IP6_DAD_UNKNO
IP6_DAD_UNKNO
W~8
W(Unknown)
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
Chain Topology
Tree Topology IP Address Type Valid IP address N/A None
Self-configuration
IPPRECEDENCE(I
DiffServ QoS IPPRECEDENCE~
Enumeration Type P Precedence), None
Support 0, DSCP~1
DSCP(DSCP)
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS HQ(High Quality),

Enumeration Type HQ~0, LQ~1 None
Support LQ(Low Quality)
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support

DiffServ QoS
Support
DiffServ QoS
Support

BASE_BOARD(Bas
None Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
Board)
Access Control
based on 802.1x
Access Control EAP-TLS(EAP-TLS

Enumeration Type EAP-TLS~13 None
based on 802.1x authentic method)
Access Control
based on 802.1x
Access Control
based on 802.1x
NULL(NULL),
LIC_OFF(License
Off),
NOTIFY_FAIL(Notifi NULL~0,
cation LIC_OFF~1,
Access Control
Enumeration Type Authentication NOTIFY_FAIL~2, None
based on 802.1x
Failed), NO_CERT~3,
NO_CERT(Certifica PORT_DOWN~6
te Not Exist),
PORT_DOWN(Tran
sport Not Activated)
Access Control
based on 802.1x
UNAUTHENTICAT
ED(Unauthenticate
d), UNAUTHENTICAT
AUTHENTICATING ED~0,
(Authenticating), AUTHENTICATING
AUTHENTIC_SUC ~1,
Access Control CEED(Authenticate AUTHENTIC_SUC
based on 802.1x Succeed), CEED~2,
AUTHENTIC_FAIL( AUTHENTIC_FAIL~
Authenticate Fail), 3,
DHCP_AUTHENTI DHCP_AUTHENTI
CATING(DHCP CATING~4
Activation
Authenticating)
Access Control
based on 802.1x
Access Control
based on 802.1x
DiffServ QoS
Support
VLAN Support
(IEEE 802.1p/q)

ALLPORT(All
Ports), ALLPORT~0,
SINGLEPORT(Sing SINGLEPORT~1
le Port)
E1_UNBA(E1
Unbalance), E1_UNBA~0,
E1_BA(E1 E1_BA~1, T1~2
Balance), T1(T1)
E1_DOUBLE_FRA
ME(E1 Double
Frames),
E1_DOUBLE_FRA
E1_CRC4_MULTI_
ME~0,
FRAME(E1 CRC4
E1_CRC4_MULTI_
Multiple Frames),
FRAME~1,
None Enumeration Type T1_SUPER_FRAM None
T1_SUPER_FRAM
E(T1 Super
E~2,
Frames),
T1_EXTENDED_S
T1_EXTENDED_S
UPER_FRAME~3
UPER_FRAME(T1
Extended Super
Frames)
HDB3(E1 HDB3
Code), AMI(E1/T1
HDB3~0, AMI~1,
None Enumeration Type AMI Code), None
B8ZS~2
B8ZS(T1 B8ZS
Code)
MASTER(Master
Mode), MASTER~0,
SLAVE(Slave SLAVE~1
Mode)
OK(Available),
LOCAL_LOOP(Loc
al Loop),
REMOTE_LOOP(R
emote Loop),
PAYLOAD_LOOP(P OK~0,
ayload Loop), LOCAL_LOOP~1,
SINGLE_CH_LOO REMOTE_LOOP~2
P(Single Channel ,
Loop), LOS(Loss of PAYLOAD_LOOP~
Signal), AIS(Alarm 3,
Indication Signal), SINGLE_CH_LOO
None Enumeration Type LFA(Loss of Frame P~4, LOS~5, None
Alignment), AIS~6, LFA~7,
RA(Remote Alarm RA~8, LMFA~9,
Indication), SLIP~10,
LMFA(Loss of OTHERS~11,
Multiframe BACKUP~12,
Alignment), PHYSICAL_LOOP~
SLIP(Slip), 13
OTHERS(Other
Fault),
BACKUP(Backup),
PHYSICAL_LOOP(
Physical Loop)
EXECUTELINKTES
TFlAG_0(No Test), EXECUTELINKTES
EXECUTELINKTES TFlAG_0~0,
TFlAG_1(Offline EXECUTELINKTES
Test), TFlAG_1~1,
EXECUTELINKTES EXECUTELINKTES
TFlAG_2(Online TFlAG_2~2
Test)
BASE_BOARD(Bas
BASE_BOARD~0,
e Board),
None Enumeration Type E1_COVERBOARD None
E1_COVERBOARD
~3
(E1 Cover Board)
E1_UNBA(E1
Unbalance), E1_UNBA~0,
E1_BA(E1 E1_BA~1, T1~2,
Balance), T1(T1), UNKNOWN~42949
UNKNOWN(Unkno 67294
wn)
E1_DOUBLE_FRA
ME(E1 Double
Frames),
E1_CRC4_MULTI_
E1_DOUBLE_FRA
FRAME(E1 CRC4
ME~0,
Multiple Frames),
E1_CRC4_MULTI_
T1_SUPER_FRAM
FRAME~1,
E(T1 Super
T1_SUPER_FRAM
Frames),
E~2,
None Enumeration Type T1_EXTENDED_S None
T1_EXTENDED_S
UPER_FRAME(T1
UPER_FRAME~3,
Extended Super
E1_MODIFY_CRC4
Frames),
_MULTIFRAME~4,
E1_MODIFY_CRC4
UNKNOWN~42949
_MULTIFRAME(Mo
67294
dify CRC4 Multiple
Frames),
UNKNOWN(Unkno
wn)
HDB3(E1 HDB3
Code), AMI(E1/T1
HDB3~0, AMI~1,
AMI Code),
B8ZS~2,
None Enumeration Type B8ZS(T1 B8ZS None
UNKNOWN~42949
Code),
67294
UNKNOWN(Unkno
wn)
1E-3(1E-3), 1E-
1E-3~3, 1E-4~4,
None Enumeration Type 4(1E-4), 1E-5(1E- None
1E-5~5, 1E-6~6
5), 1E-6(1E-6)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
BASE_BOARD(Bas
Ethernet e Board), BASE_BOARD~0,
OAM(IEEE Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
802.3ah) D(Ethernet Cover D~5
Board)
Ethernet
OAM(IEEE Enumeration Type ETH(Ethernet Port) ETH~3 None
802.3ah)
Ethernet
802.3ah)
PASSIVE(Passive
Ethernet
Mode), PASSIVE~0,
ACTIVE(Active ACTIVE~1
802.3ah)
Mode)
Ethernet
10,20,50,100,200,5
OAM(IEEE Interval Type N/A ms
00,1000
802.3ah)
Ethernet
OAM(IEEE Interval Type 64~1518 N/A byte
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
OAM(IEEE Interval Type 1~60 N/A s
802.3ah)
Ethernet
802.3ah)
Ethernet
OAM(IEEE Interval Type 10~900 N/A s
802.3ah)
Ethernet
802.3ah)
OAM3AH_SESSIO
N_IDLE(Idle
Phase),
OAM3AH_SESSIO
OAM3AH_SESSIO
N_DISCOVER(Disc
N_IDLE~0,
over Phase),
OAM3AH_SESSIO
OAM3AH_SESSIO
N_DISCOVER~1,
Ethernet N_DETECT(Detect
OAM3AH_SESSIO
OAM(IEEE Enumeration Type Phase), None
N_DETECT~2,
802.3ah) OAM3AH_SESSIO
OAM3AH_SESSIO
N_LB_LOCAL(Loop
N_LB_LOCAL~3,
back Response
OAM3AH_SESSIO
Phase),
N_LB_REMOTE~4
OAM3AH_SESSIO
N_LB_REMOTE(Lo
opback Start
Phase)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
Ethernet
802.3ah)
BASE_BOARD(Bas
None Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
Board)

COPPER(Copper),
FIBER(Fiber), COPPER~0,
AUTO(Automatic FIBER~1, AUTO~2
Detection)
None Interval Type 46~1800 N/A byte

10M(10M),
100M(100M),
10M~0, 100M~1,
None Enumeration Type 1000M(1000M), None
1000M~2, AUTO~3
AUTO(Automatic
Negotiation)
FULL(Full Duplex),
None Enumeration Type AUTO(Automatic FULL~1, AUTO~2 None
Negotiation)
CLOSE(Close), CLOSE~0,
OPEN(Open) OPEN~1
None Compound Type 14 characters N/A None

UP(Up),
None Enumeration Type UP~0, DOWN~1 None
DOWN(Down)
NOLOOP(No
Loop), NOLOOP~0,
REMOTE(Remote REMOTE~1
Loopback)
None Interval Type 0~4294967295 N/A byte/s
None Interval Type 0~10 N/A byte/s
FORCE(Force),
FORCE~0,
None Enumeration Type AUTO(Automatic None
AUTO~1
Negotiation)
FORCE(Force),
FORCE~0,
None Enumeration Type AUTO(Automatic None
AUTO~1
Negotiation)
10M(10M),
100M(100M),
10M~0, 100M~1,
None Enumeration Type 1000M(1000M), None
1000M~2, AUTO~3
AUTO(Automatic
Negotiation)
HALF(Half Duplex),
FULL(Full Duplex), HALF~0, FULL~1,
AUTO(Automatic AUTO~2
Negotiation)
FORCE(Force),
AUTO(Automatic FORCE~0,
None Enumeration Type Negotiation), AUTO~1, None
UNKNOWN(Unkno UNKNOWN~2
wn)
10M(10M),
100M(100M),
1000M(1000M), 10M~0, 100M~1,
None Enumeration Type AUTO(Automatic 1000M~2, AUTO~3, None
Negotiation), UNKNOWN~4
UNKNOWN(Unkno
wn)
HALF(Half Duplex),
FULL(Full Duplex),
HALF~0, FULL~1,
AUTO(Automatic
None Enumeration Type AUTO~2, None
Negotiation),
UNKNOWN~3
UNKNOWN(Unkno
wn)
UP(Up),
DOWN(Down)
Ethernet Link
Aggregation(IEEE Interval Type 0~7 N/A None
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
DISABLE(Disable
Ethernet Link
LACP), DISABLE~0,
Aggregation(IEEE Enumeration Type None
ENABLE(Enable ENABLE~1
802.3ad)
LACP)
Ethernet Link
Aggregation(IEEE Enumeration Type None
802.3ad)
BASE_BOARD(Bas
Ethernet Link e Board), BASE_BOARD~0,
Aggregation(IEEE Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
802.3ad) D(Ethernet Cover D~5
Board)
Ethernet Link
Aggregation(IEEE Interval Type 46~1800 N/A byte
802.3ad)
Ethernet Link
UP(Up),
Aggregation(IEEE Enumeration Type UP~0, DOWN~1 None
DOWN(Down)
802.3ad)
Ethernet Link
Aggregation(IEEE Compound Type 14 characters N/A None
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
Character String
Aggregation(IEEE 0~7 characters N/A None
Type
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
Character String
Aggregation(IEEE 0~7 characters N/A None
Type
802.3ad)
Ethernet Link
Aggregation(IEEE Interval Type 0~4294967295 N/A packet
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
Aggregation(IEEE IP Address Type Valid IP address N/A None
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)
Ethernet Link
Aggregation(IEEE Enumeration Type NO(No), YES(Yes) NO~0, YES~1 None
802.3ad)
BASE_BOARD(Bas
Ethernet Link e Board), BASE_BOARD~0,
Aggregation(IEEE Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
802.3ad) D(Ethernet Cover D~5
Board)
Ethernet Link
UP(Up),
Aggregation(IEEE Enumeration Type UP~0, DOWN~1 None
DOWN(Down)
802.3ad)
Ethernet Link
802.3ad)
SHORT(Short
Ethernet Link Timeout), SHORT~0,
Aggregation(IEEE Enumeration Type LONG(Long LONG~1, None
802.3ad) Timeout), NULL~255
NULL(NULL)
SHORT(Short
Ethernet Link Timeout), SHORT~0,
Aggregation(IEEE Enumeration Type LONG(Long LONG~1, None
802.3ad) Timeout), NULL~255
NULL(NULL)
Ethernet Link
802.3ad)
Ethernet Link
802.3ad)

HQ(High Quality),
None Enumeration Type HQ~0, LQ~1 None
LQ(Low Quality)
ARP(ARP),
ICMP(ICMP), ARP~0, ICMP~1,
Integrated Firewall Enumeration Type TCP(TCP), TCP~2, SYN~3, None
SYN(SYN), UDP~4
UDP(UDP)
Integrated Firewall Interval Type 1~4096 N/A packet/s
Integrated Firewall Interval Type 0~4294967295 N/A None

Transport DISABLE(Disable), DISABLE~0,
Overbooking ENABLE(Enable) ENABLE~1
SINGLE_RATE(Sin
Enhanced
gle Rate), SINGLE_RATE~0,
Transmission QoS Enumeration Type None
DUAL_RATE(Dual DUAL_RATE~1
Management
Rate)
Enhanced
Transmission QoS Interval Type 0~1200 N/A s
Management

Character String
IPsec 0~31 characters N/A None
Type
IPsec Interval Type 0,20~28800 N/A s
IPsec Interval Type 0,60~28800 N/A s
IPsec Interval Type 0~63 N/A None

Character String
Type
IKE_V1(IKE V1), IKE_V1~1,

IPsec Enumeration Type None
IKE_V2(IKE V2) IKE_V2~2
MAIN(Main Mode),
MAIN~2,
IPsec Enumeration Type AGGRESSIVE(Agg None
AGGRESSIVE~4
ressive Mode)
IP(IP Identify),
IPsec Enumeration Type FQDN(Name IP~1, FQDN~2 None
Identify)
IPsec IP Address Type Valid IP address N/A None
Character String
Type
IPsec Password Type 0~127 characters N/A None
DISABLE(Disable),
DISABLE~0,
IPsec Enumeration Type PERIODIC(Periodic None
PERIODIC~2
)
IPsec Interval Type 10~3600 N/A s

IPsec IP Address Type Valid IP address N/A None

Character String
Type
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IKE_V1(IKE V1), IKE_V1~1,
IKE_V2(IKE V2) IKE_V2~2
IPsec for IPv6
IPv4/IPv6 Dual MAIN(Main Mode),
MAIN~2,
Stack Enumeration Type AGGRESSIVE(Agg None
AGGRESSIVE~4
IPsec for IPv6 ressive Mode)
IPv4/IPv6 Dual FQDN(Name

Stack Enumeration Type Identify), IPV6(IPv6 FQDN~2, IPV6~5 None
IPsec for IPv6 Identify)
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Character String
Type
IPsec for IPv6
IPv4/IPv6 Dual
Stack Password Type 0~127 characters N/A None
IPsec for IPv6
IPv4/IPv6 Dual DISABLE(Disable),

DISABLE~0,
Stack Enumeration Type PERIODIC(Periodic None
PERIODIC~2
IPsec for IPv6 )
IPv4/IPv6 Dual
Stack Interval Type 10~3600 N/A s
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
DES(DES),
DES~2, 3DES~3,
3DES(3DES),
AES128~11,
IPsec Enumeration Type AES128(AES128), None
AES192~12,
AES192(AES192),
AES256~13
AES256(AES256)
MD5(MD5),
SHA1(SHA1), MD5~4, SHA1~5,
AES_XCBC_96(AE AES_XCBC_96~6
S_XCBC_96)
PRE_SHARED_KE
Y(Pre-shared Key), PRE_SHARED_KE
IPsec Enumeration Type IKE_RSA_SIG(RSA Y~8, None
Digital Certificate IKE_RSA_SIG~9
Signature)
DH_GROUP1(768-
bit Diffie-Hellman
Group),
DH_GROUP2(1024
-bit Diffie-Hellman DH_GROUP1~6,
Group), DH_GROUP2~7,
DH_GROUP14(204 DH_GROUP14~14,
8-bit Diffie-Hellman DH_GROUP15~15
Group),
DH_GROUP15(307
Group)

HMAC_MD5(HMAC
_MD5),
HMAC_MD5~14,
HMAC_SHA1(HMA
IPsec Enumeration Type HMAC_SHA1~15, None
C_SHA1),
AES128_XCBC~18
AES128_XCBC(AE
S128_XCBC)
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
Subnet Mask Type Valid Mask address N/A None
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
Enumeration Type IP(IP) IP~1 None
side(eNodeB)
2G/3G and LTE Co-
transmission
BASE_BOARD(Bas
e Board),
IP-Based Multi- BASE_BOARD~0,
E1_COVERBOARD
mode Co- E1_COVERBOARD
(E1 Cover Board),
Transmission on BS ~3,
Enumeration Type BACK_BOARD(Bac None
side(eNodeB) BACK_BOARD~4,
k Board),
2G/3G and LTE Co- ETH_COVERBOAR
ETH_COVERBOAR
transmission D~5
D(Ethernet Cover
Board)
PPP(PPP Link),
IP-Based Multi-
MPGRP(Multi-link
mode Co- PPP~0, MPGRP~2,
PPP Group),
Transmission on BS ETH~3,
Enumeration Type ETH(Ethernet Port), None
side(eNodeB) ETHTRK~4,
ETHTRK(Ethernet
2G/3G and LTE Co- TUNNEL~8
Trunk),
transmission
TUNNEL(Tunnel)
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
PPP(PPP Link),
MPGRP(Multi-link
PPP Group), PPP~0, MPGRP~2,
ETH(Ethernet Port), ETH~3,
ETHTRK(Ethernet ETHTRK~4,
Trunk), LOOPINT~6
LOOPINT(Loopbac
k Interface)
Integrated Firewall Compound Type 14 characters N/A None
Integrated Firewall Compound Type 14 characters N/A None
IPV4(IPv4), IPV4~2048,
ARP(ARP), ARP~2054,
RARP(RARP), RARP~2101,
IPV6(IPv6), IPV6~34525,
802_1X(802.1X), 802_1X~34958,
LLDP(LLDP), LLDP~35020,
1588V2(1588V2), 1588V2~35063,
CFM(CFM), CFM~35074,
LACP(LACP), LACP~8915201,
3AH(3AH) 3AH~8915203
Integrated Firewall IP Address Type Valid IP address N/A None
ICMP(ICMP),
ICMP~1, TCP~6,
TCP(TCP),
Integrated Firewall Enumeration Type UDP~17, None
UDP(UDP),
SCTP~132
SCTP(SCTP)
Character String
Integrated Firewall 0~200 characters N/A None
Type
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual NORMAL(Normal), NORMAL~0,

Stack VLAN(Vlan) VLAN~1
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual BASE_BOARD(Bas

Enumeration Type BASE_BOARD~0 None
Stack e Board)
ETH(Ethernet Port),
TRUNK(Ethernet
IPv4/IPv6 Dual ETH~3, TRUNK~4,
Enumeration Type Trunk), None
Stack LOOPIF~6
LOOPIF(Loopback
Interface)
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual UP(UP),

Enumeration Type UP~1, DOWN~2 None
Stack DOWN(Down)
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual DISABLE(Disable), DISABLE~0,

Stack ENABLE(Enable) ENABLE~1
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack



PPP(PPP Link),
MPGRP(Multi-link
PPP~0, MPGRP~2,
PPP Group),
ETH~3,
None Enumeration Type ETH(Ethernet Port), None
ETHTRK~4,
ETHTRK(Ethernet
TUNNEL~8
Trunk),
TUNNEL(Tunnel)
QOS(QOS),
None Enumeration Type QOS~0, ANY~1 None
ANY(ANY)


HQ(High Quality),
LQ(Low Quality)
None Enumeration Type S1(S1), X2(X2) S1~0, X2~1 None
None Interval Type 0~4294967294 N/A Kbit/s

NORMAL(Normal),
NORMAL~0,
FAULT(Fault),
FAULT~1,
None Enumeration Type CHECK_DISABLE None
CHECK_DISABLE
D(IP Path Check
D~2
Disabled)
Character String
Type
BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
E1_COVERBOARD
E1_COVERBOARD
(E1 Cover Board),
~3,
None Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
k Board),
ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
S1 and X2 over ENABLE(Enable) ENABLE~1
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack QOS(QOS),
Enumeration Type QOS~0, ANY~1 None
S1 and X2 over ANY(ANY)
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
None Enumeration Type S1(S1), X2(X2) S1~0, X2~1 None

IPv4/IPv6 Dual
IPv6
IPv4/IPv6 Dual
Stack
Interval Type 0~4294967295 N/A Kbit/s
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
NORMAL(Normal),
IPv4/IPv6 Dual NORMAL~0,
FAULT(Fault),
Stack FAULT~1,
Enumeration Type CHECK_DISABLE None
S1 and X2 over CHECK_DISABLE
D(IP Path Check
IPv6 D~2
Disabled)
IPv4/IPv6 Dual
S1 and X2 over Type
IPv6

HQ(High Quality),
LQ(Low Quality)
IP Performance
Monitoring
IP Performance
Monitoring
IP Performance
Monitoring
IP Performance
Monitoring
IP Performance UP(Uplink),
Enumeration Type UP~1, BIDIR~2 None
Monitoring BIDIR(Bidirection)
IP Performance
Monitoring
IP Performance
Interval Type -10000~10000 N/A ms
Monitoring
IP Performance
Interval Type -10000~10000 N/A ms
Monitoring
IP Performance
Interval Type 0~1000 N/A per mill
Monitoring
IP Performance
Monitoring
IDLE(IDLE),
IDLE~0,
ACTING(ACTING),
ACTING~1,
IP Performance PMUP(IP PM UP),
Enumeration Type PMUP~2, None
Monitoring DEACTING(DEACT
DEACTING~3,
ING),
UNKNOWN~255
UNKNOWN(NULL)
IDLE(IDLE),
IDLE~0,
ACTING(ACTING),
ACTING~1,
IP Performance PMUP(IP PM UP),
Enumeration Type PMUP~2, None
Monitoring DEACTING(DEACT
DEACTING~3,
ING),
UNKNOWN~255
UNKNOWN(NULL)
FOUR_TUPLE(FO
IP Performance UR_TUPLE), FOUR_TUPLE~0,
Monitoring THREE_TUPLE(TH THREE_TUPLE~2
REE_TUPLE)
IP Performance
Monitoring
IP Performance
Monitoring
IP Performance
Monitoring
IP Performance
Monitoring
IP Performance
Monitoring

IPPMVER_V1(Versi
on 1.0), IPPMVER_V1~1,
IPPMVER_V2(Versi IPPMVER_V2~2
on 2.0)
BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
E1_COVERBOARD
E1_COVERBOARD
(E1 Cover Board),
~3,
None Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
k Board),
ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
PPP(PPP Link),
MPGRP(Multi-link PPP~0, MPGRP~2,
PPP Group), TUNNEL~8
TUNNEL(Tunnel)

NEXTHOP(Next
None Enumeration Type Hop), IF(Exit NEXTHOP~0, IF~1 None
Interface)


STATICHOST(Stati
c Host Route),
STATICGATEWAY(
STATICHOST~1,
Static Gateway
STATICGATEWAY~
None Enumeration Type Route), None
2, HOST~3,
HOST(Dynamic
GATEWAY~4
Host Route),
GATEWAY(Dynami
c Gateway Route)
Character String
Type
PPP(PPP Link),
MPGRP(Multi-link
PPP Group),
PPP~0, MPGRP~2,
ETH(Ethernet Port),
ETH~3,
ETHTRK(Ethernet
None Enumeration Type ETHTRK~4, None
Trunk),
LOOPINT~6, VI~7,
LOOPINT(Loopbac
TUNNEL~8
k Interface),
VI(Virtual Interface),
TUNNEL(Tunnel)

IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual NEXTHOP(Next

Enumeration Type NEXTHOP~0 None
Stack Hop)
IPADDR6_TYPE_G
LOBAL_UNICAST( IPADDR6_TYPE_G
Global Unicast LOBAL_UNICAST~
IPv4/IPv6 Dual
Enumeration Type Address), 0, None
Stack
IPADDR6_TYPE_LI IPADDR6_TYPE_LI
NK_LOCAL(Link NK_LOCAL~2
Local Address)
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
STATICHOST(Stati
c Host Route),
STATICGATEWAY(
STATICHOST~1,
Static Gateway
IPv4/IPv6 Dual STATICGATEWAY~
Enumeration Type Route), None
Stack 2, HOST~3,
HOST(Dynamic
GATEWAY~4
Host Route),
GATEWAY(Dynami
c Gateway Route)
IPv4/IPv6 Dual Character String

Stack Type
Ipsec Interval Type 0~7 N/A None

BASE_BOARD(Bas
IPsec Enumeration Type ETH_COVERBOAR ETH_COVERBOAR None
Board)
ETH(Ethernet Port),
IPsec Enumeration Type ETHTRK(Ethernet ETH~3, ETHTRK~4 None
Trunk)
Character String
Type
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Character String
Type
IPsec for IPv6
Character String
Type
Character String
Type

MASTER(Master
IPSec Policy), MASTER~0,
SLAVE(Slave IPSec SLAVE~1
Policy)
Character String
Type
Character String
Type
Character String
Type
DISABLE(Disable),
PFS_GROUP1(768
-bit Diffie-Hellman DISABLE~0,
IPsec Enumeration Type Group), PFS_GROUP1~1, None
PFS_GROUP2(102 PFS_GROUP2~2
Group)
GLOBAL(Global
Configuration), GLOBAL~0,
LOCAL(Local LOCAL~1
Configuration)
0,1843200~429496
IPsec Interval Type N/A KB
7295

WND_DISABLE(0), WND_DISABLE~0,
WND_32(32), WND_32~1,
WND_64(64), WND_64~2,
WND_128(128), WND_128~128,
IPsec Enumeration Type WND_256(256), WND_256~256, None
WND_512(512), WND_512~512,
WND_1024(1024), WND_1024~1024,
WND_2048(2048), WND_2048~2048,
WND_4096(4096) WND_4096~4096
IPv4/IPv6 Dual
Character String
Type
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPV4(IPv4),
Stack Enumeration Type IPV4~4, IPV6~6 None
IPV6(IPv6)
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
Character String
Type
IPsec for IPv6
IPv4/IPv6 Dual
Character String
Type
IPsec for IPv6
DISABLE(Disable),
PFS_GROUP1(768
IPv4/IPv6 Dual -bit Diffie-Hellman DISABLE~0,
Stack Enumeration Type Group), PFS_GROUP1~1, None
IPsec for IPv6 PFS_GROUP2(102 PFS_GROUP2~2
Group)
GLOBAL(Global
IPv4/IPv6 Dual
Configuration), GLOBAL~0,
LOCAL(Local LOCAL~1
IPsec for IPv6
Configuration)
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
0,1843200~429496
Stack Interval Type N/A KB
7295
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
IPv4/IPv6 Dual
IPsec for IPv6
Character String
Type
TUNNEL(Tunnel),
TUNNEL~0,
IPsec Enumeration Type TRANSPORT(Tran None
TRANSPORT~1
sport)
AH(AH Protocol),
ESP(ESP Protocol), AH~0, ESP~1,
AH_ESP(AH/ESP AH_ESP~2
Protocol)
MD5(MD5),
SHA1(SHA1), AES-
MD5~1, SHA1~2,
XCBC-MAC-
IPsec Enumeration Type AES-XCBC-MAC- None
96(AES-XCBC-
96~5, SHA256~12
MAC-96),
SHA256(SHA256)
NULL(NULL),
MD5(MD5),
NULL~0, MD5~1,
SHA1(SHA1), AES-
SHA1~2, AES-
IPsec Enumeration Type XCBC-MAC- None
XCBC-MAC-96~5,
96(AES-XCBC-
SHA256~12
MAC-96),
SHA256(SHA256)
NULL(NULL),
NULL~0, DES~1,
DES(DES),
3DES~2,
3DES(3DES),
IPsec Enumeration Type AES128~6, None
AES128(AES128),
AES192~7,
AES192(AES192),
AES256~8
AES256(AES256)
UP(Up),
DOWN(Down)


IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IP6_DAD_OK(Valid
IP6_DAD_OK~1,
),
IP6_DAD_TENTATI
IP6_DAD_TENTATI
VE~2,
IPv4/IPv6 Dual VE(Tentative),
Enumeration Type IP6_DAD_DUPLIC None
Stack IP6_DAD_DUPLIC
ATED~4,
ATED(Duplicate),
IP6_DAD_UNKNO
IP6_DAD_UNKNO
W~8
W(Unknown)
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
Transport
Overbooking
Transport Interval Type 0~7 N/A None
Differentiated Flow
Control
Transport
Overbooking
Differentiated Flow
Control
Transport
Overbooking
Differentiated Flow
Control
MPGRP(Multi-link
Transport
PPP Group),
Overbooking MPGRP~2, ETH~3,
ETH(Ethernet Port),
Transport Enumeration Type ETHTRK~4, None
ETHTRK(Ethernet
Differentiated Flow TUNNEL~8
Trunk),
Control
TUNNEL(Tunnel)
Transport
Overbooking
Differentiated Flow
Control
Transport
Overbooking
Transport Enumeration Type None
Differentiated Flow
Control
Transport
Overbooking
Transport Interval Type 32~1000000 N/A Kbit/s
Differentiated Flow
Control
Transport
Overbooking
Transport Interval Type 32~1000000 N/A Kbit
Differentiated Flow
Control
Transport
Overbooking
Transport Interval Type 0~1000000 N/A Kbit
Differentiated Flow
Control
BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
Transport E1_COVERBOARD
E1_COVERBOARD
Overbooking (E1 Cover Board),
~3,
Transport Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
Differentiated Flow k Board),
ETH_COVERBOAR
Control ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
Transport
Overbooking
Transport Interval Type 32~1000000 N/A Kbit/s
Differentiated Flow
Control
ML-PPP/MC-PPP Interval Type 0~7 N/A None

ML-PPP/MC-PPP Enumeration Type None
NONAUTH(No
Authentication),
PAP(PAP NONAUTH~0,
Authentication), PAP~1, CHAP~2
CHAP(CHAP
Authentication)
Character String
ML-PPP/MC-PPP 1~67 characters N/A None
Type
ML-PPP/MC-PPP Password Type 1~19 characters N/A None

ML-PPP/MC-PPP IP Address Type Valid IP address N/A None
ML-PPP/MC-PPP Subnet Mask Type Valid Mask address N/A None
LONG(Long), LONG~0,
SHORT(Short) SHORT~1
ML-PPP/MC-PPP Interval Type 128~1500 N/A byte

ML-PPP/MC-PPP Interval Type 1~1000 N/A ms
ML-PPP/MC-PPP Interval Type 4,8 N/A None
ML-PPP/MC-PPP Interval Type 0~1000 N/A per mill
ML-PPP/MC-PPP Interval Type 0~1000 N/A per mill
UP(Up),
ML-PPP/MC-PPP Enumeration Type UP~1, DOWN~2 None
DOWN(Down)
INITIAL(INITIAL),
STARTING(STARTI
NG),
CLOSED(CLOSED)
,
INITIAL~1,
STOPPED(STOPP
STARTING~2,
ED),
CLOSED~3,
CLOSING(CLOSIN
STOPPED~4,
G),
CLOSING~5,
ML-PPP/MC-PPP Enumeration Type STOPPING(STOPP None
STOPPING~6,
ING),
REQSENT~7,
REQSENT(REQSE
ACKRCVD~8,
NT),
ACKSENT~9,
ACKRCVD(ACKRC
OPENED~10
VD),
ACKSENT(ACKSE
NT),
OPENED(OPENED
)
INITIAL(INITIAL),
STARTING(STARTI
NG),
CLOSED(CLOSED)
,
INITIAL~1,
STOPPED(STOPP
STARTING~2,
ED),
CLOSED~3,
CLOSING(CLOSIN
STOPPED~4,
G),
CLOSING~5,
STOPPING~6,
ING),
REQSENT~7,
REQSENT(REQSE
ACKRCVD~8,
NT),
ACKSENT~9,
ACKRCVD(ACKRC
OPENED~10
VD),
ACKSENT(ACKSE
NT),
OPENED(OPENED
)
ML-PPP/MC-PPP Interval Type 0~4294967295 N/A packet
ML-PPP/MC-PPP Interval Type 0~4294967295 N/A byte/s
ML-PPP/MC-PPP Interval Type 0~4294967295 N/A byte/s
BASE_BOARD(Bas
BASE_BOARD~0,
e Board),
ML-PPP/MC-PPP Enumeration Type E1_COVERBOARD None
E1_COVERBOARD
~3
(E1 Cover Board)


TS1(Time Slot 1),
TS2(Time Slot 2),
TS3(Time Slot 3),
TS4(Time Slot 4),
TS1~0, TS2~1,
TS5(Time Slot 5),
TS3~2, TS4~3,
TS6(Time Slot 6),
TS5~4, TS6~5,
TS7(Time Slot 7),
TS7~6, TS8~7,
TS8(Time Slot 8),
TS9~8, TS10~9,
TS9(Time Slot 9),
TS11~10, TS12~11,
TS10(Time Slot10),
TS13~12,
TS11(Time Slot11),
TS14~13,
TS12(Time Slot12),
TS15~14,
TS13(Time Slot13),
TS16~15,
TS14(Time Slot14),
TS17~16,
TS15(Time Slot15),
TS18~17,
ML-PPP/MC-PPP Bit Field Type TS16(Time Slot16), None
TS19~18,
TS17(Time Slot17),
TS20~19,
TS18(Time Slot18),
TS21~20,
TS19(Time Slot19),
TS22~21,
TS20(Time Slot20),
TS23~22,
TS21(Time Slot21),
TS24~23,
TS22(Time Slot22),
TS25~24,
TS23(Time Slot23),
TS26~25,
TS24(Time Slot24),
TS27~26,
TS25(Time Slot25),
TS28~27,
TS26(Time Slot26),
TS29~28,
TS27(Time Slot27),
TS30~29, TS31~30
TS28(Time Slot28),
TS29(Time Slot29),
TS30(Time Slot30),
TS31(Time Slot31)
ML-PPP/MC-PPP Interval Type 1~65535 N/A ms
BASE_BOARD(Bas
BASE_BOARD~0,
e Board),
E1_COVERBOARD
~3
(E1 Cover Board)
BASE_BOARD(Bas
BASE_BOARD~0,
e Board),
E1_COVERBOARD
~3
(E1 Cover Board)
UP(Up),
ML-PPP/MC-PPP Enumeration Type UP~1, DOWN~2 None
DOWN(Down)
INITIAL(INITIAL),
STARTING(STARTI
NG),
CLOSED(CLOSED)
,
INITIAL~1,
STOPPED(STOPP
STARTING~2,
ED),
CLOSED~3,
CLOSING(CLOSIN
STOPPED~4,
G),
CLOSING~5,
STOPPING~6,
ING),
REQSENT~7,
REQSENT(REQSE
ACKRCVD~8,
NT),
ACKSENT~9,
ACKRCVD(ACKRC
OPENED~10
VD),
ACKSENT(ACKSE
NT),
OPENED(OPENED
)
BASE_BOARD(Bas
BASE_BOARD~0,
e Board),
E1_COVERBOARD
~3
(E1 Cover Board)

Centralized M2000 MASTER(Master), MASTER~0,

Management SLAVE(Slave) SLAVE~1
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Enumeration Type IPV4(IPV4) IPV4~1 None
Management
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
NEXTHOP(Next
Centralized M2000
Enumeration Type Hop), IF(Exit NEXTHOP~0, IF~1 None
Management
Interface)
PPP(PPP Link),
Centralized M2000 MPGRP(Multi-link PPP~0, MPGRP~2,
Management PPP Group), TUNNEL~8
TUNNEL(Tunnel)
Centralized M2000
Management
Centralized M2000
Management
Centralized M2000
Management
NORMAL(Normal),
ABNORMAL(Abnor NORMAL~0,
Centralized M2000
Enumeration Type mal), ABNORMAL~1, None
Management
wn)
Centralized M2000 INUSE(In Use), INUSE~0,

Management UNUSED(Unused) UNUSED~1
BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
BACK_BOARD(Bac
Centralized M2000 BACK_BOARD~4,
Enumeration Type k Board), None
Management ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
IPv4/IPv6 Dual
Stack
Centralized M2000
Management
IPv4/IPv6 Dual
Stack
Centralized M2000
Management
NORMAL(Normal),
IPv4/IPv6 Dual
ABNORMAL(Abnor NORMAL~0,
Stack
Enumeration Type mal), ABNORMAL~1, None
Centralized M2000
Management
wn)
ETH(Ethernet Port),
ETH~3,
ETHTRK(Ethernet
Integrated Firewall Enumeration Type ETHTRK~4, None
Trunk),
TUNNEL~8
TUNNEL(Tunnel)
PERMIT(Permit), PERMIT~0,
DENY(Deny) DENY~1
BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
BACK_BOARD(Bac
BACK_BOARD~4,
Integrated Firewall Enumeration Type k Board), None
ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
Integrated Firewall Interval Type 0~4294967295 N/A packet

Integrated Firewall Interval Type 0~4294967295 N/A byte


ADV_ACL(Only
Advanced ACL),
L2_ACL(Only Layer ADV_ACL~0,
Integrated Firewall Enumeration Type 2 ACL), L2_ACL~1, None
ADV_AND_L2(Adv ADV_AND_L2~2
anced ACL and
Layer 2 ACL)
Integrated Firewall Subnet Mask Type Valid Mask address N/A None
PASSIVE(Passive
IPv4/IPv6 Dual Mode), PASSIVE~0,
Stack ACTIVE(Active ACTIVE~1
Mode)
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Stack
IPv4/IPv6 Dual
Interval Type 5~60,65535 N/A min
Stack
IPv4/IPv6 Dual
Stack

BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
E1_COVERBOARD
E1_COVERBOARD
(E1 Cover Board),
~3,
Integrated Firewall Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
k Board),
ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
ETH(Ethernet Port),
Integrated Firewall Enumeration Type ETH~0, E1T1~1 None
E1T1(E1/T1 Port)
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
NONAUTH(No
Compression & Authentication),
Multiplexing over PAP(PAP NONAUTH~0,
E1/T1 Authentication), PAP~1, CHAP~2
PPP MUX CHAP(CHAP
Authentication)
Compression &
Multiplexing over Character String
E1/T1 Type
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
TS1(Time Slot 1),

TS2(Time Slot 2),
TS3(Time Slot 3),
TS4(Time Slot 4),
TS1~0, TS2~1,
TS5(Time Slot 5),
TS3~2, TS4~3,
TS6(Time Slot 6),
TS5~4, TS6~5,
TS7(Time Slot 7),
TS7~6, TS8~7,
TS8(Time Slot 8),
TS9~8, TS10~9,
TS9(Time Slot 9),
TS11~10, TS12~11,
TS10(Time Slot10),
TS13~12,
TS11(Time Slot11),
TS14~13,
TS12(Time Slot12),
TS15~14,
TS13(Time Slot13),
TS16~15,
TS14(Time Slot14),
Compression & TS17~16,
TS15(Time Slot15),
Multiplexing over TS18~17,
Bit Field Type TS16(Time Slot16), None
E1/T1 TS19~18,
TS17(Time Slot17),
PPP MUX TS20~19,
TS18(Time Slot18),
TS21~20,
TS19(Time Slot19),
TS22~21,
TS20(Time Slot20),
TS23~22,
TS21(Time Slot21),
TS24~23,
TS22(Time Slot22),
TS25~24,
TS23(Time Slot23),
TS26~25,
TS24(Time Slot24),
TS27~26,
TS25(Time Slot25),
TS28~27,
TS26(Time Slot26),
TS29~28,
TS27(Time Slot27),
TS30~29, TS31~30
TS28(Time Slot28),
TS29(Time Slot29),
TS30(Time Slot30),
TS31(Time Slot31)
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over DISABLE(Disable), DISABLE~0,
E1/T1 ENABLE(Enable) ENABLE~1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
PPP MUX
Compression &
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over UP(Up),
Enumeration Type UP~1, DOWN~2 None
E1/T1 DOWN(Down)
PPP MUX
INITIAL(INITIAL),
STARTING(STARTI
NG),
CLOSED(CLOSED)
,
INITIAL~1,
STOPPED(STOPP
STARTING~2,
ED),
CLOSED~3,
CLOSING(CLOSIN
Compression & STOPPED~4,
G),
Multiplexing over CLOSING~5,
Enumeration Type STOPPING(STOPP None
E1/T1 STOPPING~6,
ING),
PPP MUX REQSENT~7,
REQSENT(REQSE
ACKRCVD~8,
NT),
ACKSENT~9,
ACKRCVD(ACKRC
OPENED~10
VD),
ACKSENT(ACKSE
NT),
OPENED(OPENED
)
INITIAL(INITIAL),
STARTING(STARTI
NG),
CLOSED(CLOSED)
,
INITIAL~1,
STOPPED(STOPP
STARTING~2,
ED),
CLOSED~3,
CLOSING(CLOSIN
G),
E1/T1 STOPPING~6,
ING),
PPP MUX REQSENT~7,
REQSENT(REQSE
ACKRCVD~8,
NT),
ACKSENT~9,
ACKRCVD(ACKRC
OPENED~10
VD),
ACKSENT(ACKSE
NT),
OPENED(OPENED
)
INITIAL(INITIAL),
STARTING(STARTI
NG),
CLOSED(CLOSED)
,
INITIAL~1,
STOPPED(STOPP
STARTING~2,
ED),
CLOSED~3,
CLOSING(CLOSIN
G),
E1/T1 STOPPING~6,
ING),
PPP MUX REQSENT~7,
REQSENT(REQSE
ACKRCVD~8,
NT),
ACKSENT~9,
ACKRCVD(ACKRC
OPENED~10
VD),
ACKSENT(ACKSE
NT),
OPENED(OPENED
)
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
PPP MUX
Compression &
PPP MUX
Compression &
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
PPP MUX
Compression &
Multiplexing over
Interval Type 0~4294967295 N/A packet
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
Interval Type 0~4294967295 N/A byte/s
E1/T1
PPP MUX
Compression &
Multiplexing over
Interval Type 0~4294967295 N/A byte/s
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression & BASE_BOARD(Bas

BASE_BOARD~0,
Multiplexing over e Board),
Enumeration Type E1_COVERBOARD None
E1/T1 E1_COVERBOARD
~3
PPP MUX (E1 Cover Board)
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
Compression &
Multiplexing over
E1/T1
PPP MUX
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
DiffServ QoS
Support
Enhanced
Transmission QoS Interval Type 0~7 N/A None
Management
Enhanced
Management
Enhanced
Management
Enhanced
Transmission QoS Enumeration Type IP(IP) IP~1 None
Management
BASE_BOARD(Bas
e Board),
BASE_BOARD~0,
E1_COVERBOARD
E1_COVERBOARD
Enhanced (E1 Cover Board),
~3,
Transmission QoS Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
Management k Board),
ETH_COVERBOAR
ETH_COVERBOAR
D~5
D(Ethernet Cover
Board)
PPP(PPP Link),
MPGRP(Multi-link
PPP~6, MPGRP~8,
Enhanced PPP Group),
ETH~9,
Transmission QoS Enumeration Type ETH(Ethernet Port), None
ETHTRK~10,
Management ETHTRK(Ethernet
TUNNEL~15
Trunk),
TUNNEL(Tunnel)
Enhanced
Management
0~0, 1~1, 2~2, 3~3,
4~4, 5~5, 6~6, 7~7,
0, 1, 2, 3, 4, 5, 6, 7,
8~8, 9~9, 10~10,
8, 9, 10, 11, 12, 13,
11~11, 12~12,
None Enumeration Type 14, 15, None
13~13, 14~14,
DEFAULTPORT(De
15~15,
fault Port)
DEFAULTPORT~12
7
Enhanced
Transmission QoS Enumeration Type KBPS(Kbit/s) KBPS~0 None
Management
Enhanced
Management
Enhanced
Management
Enhanced
Transmission QoS Interval Type 64~1000000 N/A Kbit
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
SINGLE_RATE(Sin
Enhanced
gle Rate), SINGLE_RATE~0,
Transmission QoS Enumeration Type None
DUAL_RATE(Dual DUAL_RATE~1
Management
Rate)
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Management
Enhanced
Transmission QoS Interval Type 0~4294967295 N/A byte/s
Management
Transport
Overbooking
Transport
Differentiated Flow Interval Type 0~7 N/A None
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
BASE_BOARD(Bas
Transport e Board),
BASE_BOARD~0,
Overbooking E1_COVERBOARD
E1_COVERBOARD
Transport (E1 Cover Board),
~3,
Differentiated Flow Enumeration Type BACK_BOARD(Bac None
BACK_BOARD~4,
Control k Board),
ETH_COVERBOAR
Transport Resource ETH_COVERBOAR
D~5
Overload Control D(Ethernet Cover
Board)
Transport PPP(PPP Link),
Overbooking MPGRP(Multi-link
PPP~6, MPGRP~8,
Transport PPP Group),
ETH~9,
Differentiated Flow Enumeration Type ETH(Ethernet Port), None
ETHTRK~10,
Control ETHTRK(Ethernet
TUNNEL~15
Transport Resource Trunk),
Overload Control TUNNEL(Tunnel)
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
0~0, 1~1, 2~2, 3~3,
Transport
4~4, 5~5, 6~6, 7~7,
Overbooking 0, 1, 2, 3, 4, 5, 6, 7,
8~8, 9~9, 10~10,
Transport 8, 9, 10, 11, 12, 13,
11~11, 12~12,
Differentiated Flow Enumeration Type 14, 15, None
13~13, 14~14,
Control DEFAULTPORT(De
15~15,
Transport Resource fault Port)
DEFAULTPORT~12
Overload Control
7
Transport
Overbooking
Transport
Differentiated Flow Enumeration Type OFF(Off), ON(On) OFF~0, ON~1 None
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Differentiated Flow Interval Type 0~1000 N/A per mill
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Differentiated Flow Interval Type 0~10000 N/A ms
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Differentiated Flow Interval Type 64~1000000 N/A Kbit/s
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Differentiated Flow Enumeration Type None
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Differentiated Flow Enumeration Type None
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Control
Transport Resource
Overload Control
Transport
Overbooking
Transport
Differentiated Flow Interval Type 0~8192 N/A packet
Control
Transport Resource
Overload Control





2), CRC32(CRC32) CRC32~1
SCTP_STAT_DOW
N(Down), SCTP_STAT_DOW
SCTP_STAT_CON N~0,
None Enumeration Type GESTION(Congesti SCTP_STAT_CON None
on), GESTION~1,
SCTP_STAT_UP(U SCTP_STAT_UP~2
p)
SCTP_TRANSFER
_CAUSE_START(S
SCTP_TRANSFER
tart),
_CAUSE_START~0
SCTP_TRANSFER
,
_CAUSE_LINKDO
SCTP_TRANSFER
WN(Link Down),
_CAUSE_LINKDO
SCTP_TRANSFER
WN~1,
_CAUSE_PORTDI
SCTP_TRANSFER
SABLED(Port
_CAUSE_PORTDI
Disabled),
SABLED~2,
SCTP_TRANSFER
SCTP_TRANSFER
None Enumeration Type _CAUSE_INIT(Initia None
_CAUSE_INIT~3,
l),
SCTP_TRANSFER
SCTP_TRANSFER
_CAUSE_UNKNO
_CAUSE_UNKNO
WERROR~4,
WERROR(Unknow
SCTP_TRANSFER
n Error),
_CAUSE_NORMAL
SCTP_TRANSFER
~5,
_CAUSE_NORMAL
SCTP_TRANSFER
(Normal),
_CAUSE_USERDE
SCTP_TRANSFER
LETE~6
_CAUSE_USERDE
LETE(User Delete)
ACTIVE(Active
Path), ACTIVE~0,
STANDBY(Standby STANDBY~1
Path)
UNBLOCK(Unblock UNBLOCK~0,
), BLOCK(Block) BLOCK~1
Character String
Type
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack ALDER32(ALDER3 ALDER32~0,
S1 and X2 over 2), CRC32(CRC32) CRC32~1
IPv6
IPv4/IPv6 Dual
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
SCTP_STAT_DOW
N(Down), SCTP_STAT_DOW
IPv4/IPv6 Dual
SCTP_STAT_CON N~0,
Stack
Enumeration Type GESTION(Congesti SCTP_STAT_CON None
S1 and X2 over
on), GESTION~1,
IPv6
SCTP_STAT_UP(U SCTP_STAT_UP~2
p)
SCTP_TRANSFER
_CAUSE_START(S
SCTP_TRANSFER
tart),
_CAUSE_START~0
SCTP_TRANSFER
,
_CAUSE_LINKDO
SCTP_TRANSFER
WN(Link Down),
_CAUSE_LINKDO
SCTP_TRANSFER
WN~1,
_CAUSE_PORTDI
SCTP_TRANSFER
SABLED(Port
_CAUSE_PORTDI
Disabled),
IPv4/IPv6 Dual SABLED~2,
SCTP_TRANSFER
Stack SCTP_TRANSFER
Enumeration Type _CAUSE_INIT(Initia None
S1 and X2 over _CAUSE_INIT~3,
l),
IPv6 SCTP_TRANSFER
SCTP_TRANSFER
_CAUSE_UNKNO
_CAUSE_UNKNO
WERROR~4,
WERROR(Unknow
SCTP_TRANSFER
n Error),
_CAUSE_NORMAL
SCTP_TRANSFER
~5,
_CAUSE_NORMAL
SCTP_TRANSFER
(Normal),
_CAUSE_USERDE
SCTP_TRANSFER
LETE~6
_CAUSE_USERDE
LETE(User Delete)
IPv4/IPv6 Dual
Stack
Compound Type None N/A None
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual
Stack
S1 and X2 over
IPv6
IPv4/IPv6 Dual ACTIVE(Active

Stack Path), ACTIVE~0,
S1 and X2 over STANDBY(Standby STANDBY~1
IPv6 Path)
IPv4/IPv6 Dual
Stack UNBLOCK(Unblock UNBLOCK~0,
S1 and X2 over ), BLOCK(Block) BLOCK~1
IPv6
IPv4/IPv6 Dual
S1 and X2 over Type
IPv6
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport Resource
Overload Control
Different Transport Interval Type 0~100 N/A %
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport Resource
Overload Control
Paths based on
QoS Grade
Intra-LTE Load
Balancing
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Transport
Overbooking
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Intra-LTE Load
Balancing
Transport Resource
Overload Control
Transport Resource
Overload Control
Transport Resource
Overload Control
Transport Resource
Overload Control
Transport Resource
Overload Control
Transport Resource
Overload Control
Transport Resource
Overload Control
WHITELIST(Whiteli
st), WHITELIST~1,
BLACKLIST(Blackli BLACKLIST~2
st)



IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
IP-Based Multi-
mode Co-
Transmission on BS
side(eNodeB)
2G/3G and LTE Co-
transmission
VLAN Support
(IEEE 802.1p/q)
USERDATA(User
Data),
SIG(Signaling
Data),
OTHER(Other USERDATA~0,
VLAN Support Data), SIG~1, OTHER~3,
(IEEE 802.1p/q) OM_HIGH(High OM_HIGH~4,
Level Maintenance OM_LOW~5
Data),
OM_LOW(Low
Level Maintenance
Data)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
SINGLEVLAN(Singl
VLAN Support e VLAN), SINGLEVLAN~0,
(IEEE 802.1p/q) VLANGROUP(VLA VLANGROUP~1
N Group)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
VLAN Support
(IEEE 802.1p/q)
VLAN Support DISABLE(Disable), DISABLE~0,

(IEEE 802.1p/q) ENABLE(Enable) ENABLE~1

Actual Value Recommended Initial Value
Default Value Impact
Range Value Setting Source
Equipment
0~35 None None BFANT
Planning
Equipment
0 0 0 BFANT
Planning
Equipment
60~254 None None BFANT
Planning
Equipment
0 0 None BFANT
Planning
Equipment
0~128 characters NULL None BFANT
Planning
Equipment
0~15 0 None BFANT
Planning
Default/Recommen
30,65,90,360 30 None BFANT
ded Value
Default/Recommen
33~64 33 None BFANT
ded Value
INTELLIGENT,
INTELLIGENT None N/A BFANT
DISTRIBUTED
SINGLE, DUAL None None N/A BFANT
0~360 None None N/A BFANT
FOURPORTS, FOURPORTS(Four
None N/A BFANT
EIGHTPORTS Ports)
0~1, step:0.01 None None N/A BFANT
-180~180 None None N/A BFANT


Radio Planning
0~1048575 0 None eNodeB
(Internal planning)
Radio Planning
1~64 characters DBS3900 LTE None eNodeB
(Internal planning)
DBS3900_LTE,
BTS3900_LTE,
DBS3900_LTE(DB Equipment
BTS3900A_LTE, None eNodeB
S3900 LTE) Planning
BTS3900L_LTE,
BTS3900AL_LTE
ON, OFF OFF(OFF) None Engineering Design eNodeB
22:00:00~5:00:00 00:00:00 None Engineering Design eNodeB
23:00:00~6:00:00 06:00:00 None Engineering Design eNodeB
-180~180, step:1e- Radio Planning

0 None eNodeB
6 (Internal planning)
Radio Planning
-90~90, step:1e-6 0 None eNodeB
(Internal planning)
0~20 characters None None N/A eNodeB
Default, Normal,
Demo, Protected, None None N/A eNodeB
Emergency
Poweroff, Normal None None N/A eNodeB
Radio Planning
0~128 characters NULL None eNodeB
(Internal planning)
Equipment
DEG, SEC DEG None eNodeB
Planning
Radio Planning
0~16 characters 0:0:0 None eNodeB
(Internal planning)
Radio Planning
0~16 characters 0:0:0 None eNodeB
(Internal planning)
Equipment
CPRI, TDL_IR CPRI None eNodeB
Planning
Transmission_Pack
et_Loss_Rate,
Transmission_Delay
,
Transmission_Jitter,
Packet_Loss_Rate,
Cell_RRC_Connect
_Succ_Rate,
Cell_ERAB_Setup_
Succ_Rate,
Cell_Call_Drop_Rat Equipment
None None KPIALARM
e, Intra- Planning
Frequency_HO_Su
cc_Rate, Inter-
Frequency_HO_Su
cc_Rate, LTE-
CDMA_Handover_
Succ_Rate, LTE-
WCDMA_Handover
_Succ_Rate, LTE-
GERAN_Handover
_Succ_Rate
Default/Recommen
ON, OFF None OFF KPIALARM
ded Value
threshold is 10.
If the KPITYPE
parameter is set to
Transmission_Delay
, the recommended
threshold is 300.
If the KPITYPE
parameter is set to
the recommended
threshold is 100.
If the KPITYPE
parameter is set to
Packet_Loss_Rate,
the recommended
threshold is 5.
If the KPITYPE
parameter is set to
Cell_RRC_Connect Default/Recommen
0~4294967295 None KPIALARM
_Succ_Rate or ded Value
Cell_ERAB_Setup_
Succ_Rate, the
recommended
threshold is 90.
If the KPITYPE
parameter is set to
Intra-
Frequency_HO_Su
cc_Rate or Inter-
Frequency_HO_Su
cc_Rate, the
recommended
threshold is 85.
If the KPITYPE
parameter is set to
LTE-
CDMA_Handover_
Succ_Rate, LTE-
threshold is 5.
If the KPITYPE
parameter is set to
Transmission_Delay
, the recommended
threshold is 200.
If the KPITYPE
parameter is set to
the recommended
threshold is 50.
If the KPITYPE
parameter is set to
Packet_Loss_Rate,
the recommended
threshold is 1.
If the KPITYPE
parameter is set to
Cell_RRC_Connect Default/Recommen
0~4294967295 None KPIALARM
_Succ_Rate or ded Value
Cell_ERAB_Setup_
Succ_Rate, the
recommended
threshold is 95.
If the KPITYPE
parameter is set to
Intra-
Frequency_HO_Su
cc_Rate or Inter-
Frequency_HO_Su
cc_Rate, the
recommended
threshold is 90.
If the KPITYPE
parameter is set to
LTE-
CDMA_Handover_
Succ_Rate, LTE-
If the KPITYPE
parameter is set to
Transmission_Pack
et_Loss_Rate,
Transmission_Delay
,
or
Packet_Loss_Rate,
the recommended
value of this
parameter is 360.
If the KPITYPE
parameter is set to
Cell_RRC_Connect
_Succ_Rate,
Cell_ERAB_Setup_ Default/Recommen
0~4294967295 100 KPIALARM
Succ_Rate, ded Value
Cell_Call_Drop_Rat
e, Intra-
Frequency_HO_Su
cc_Rate, Inter-
Frequency_HO_Su
cc_Rate, LTE-
CDMA_Handover_
Succ_Rate, LTE-
WCDMA_Handover
_Succ_Rate, or
LTE-
GERAN_Handover
_Succ_Rate, the
recommended
value of this
parameter is 100.
15minutes,
60minutes(60minut Default/Recommen
30minutes, 60minutes KPIALARM
es) ded Value
60minutes, 1day
Default/Recommen
0~23 0 None KPIALARM
ded Value
Default/Recommen
1~3 1 1 KPIALARM
ded Value
Equipment
0~17 None None Sector
Planning
-180~180, step:1e- Radio Planning
None None Sector
Radio Planning
-90~90, step:1e-6 None None Sector
(Internal planning)
1T1R, 1T2R, 2T2R, Radio Planning

None None Sector
2T4R, 4T4R, 8T8R (Internal planning)
NormalMIMO, NormalMIMO(Norm Radio Planning
None Sector
AIDMIMO al MIMO) (Internal planning)
COMBTYPE_SING
LE_RRU,
COMBTYPE_TWO
_RRU,
COMBTYPE_THRE
E_RRU,
COMBTYPE_FOU
R_RRU, COMBTYPE_SING Radio Planning
None Sector
COMBTYPE_FIVE_ LE_RRU (Internal planning)
RRU,
COMBTYPE_SIX_
RRU,
COMBTYPE_SEVE
N_RRU,
COMBTYPE_EIGH
T_RRU
Equipment
Planning
Equipment
4~5,60~254 None None Sector
Planning
Equipment
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R1B, R2A, R2B, Equipment
None None Sector
R3A, R3B, R4A, Planning
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
4~5,60~254 60 None Sector
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
0~62 0 None N/A Sector
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~30 characters NULL None Sector
Planning
Radio Planning
-32767~32767 None None Sector
(Internal planning)
Radio Planning
0~1800000 3 None Sector
(Internal planning)
Radio Planning
0~1800000 3 None Sector
(Internal planning)
Radio Planning
0~179 0 None Sector
(Internal planning)
Radio Planning
0~990 3 None Sector
(Internal planning)
Radio Planning
0~100 0 None Sector
(Internal planning)
Radio Planning
DEG, SEC DEG None Sector
(Internal planning)
Radio Planning
0~16 characters 0:0:0 None Sector
(Internal planning)
Radio Planning
0~16 characters 0:0:0 None Sector
(Internal planning)
Radio Planning
FALSE, TRUE FALSE None Sector
(Internal planning)
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,
R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
Equipment
0~62 0 None Sector
Planning
Equipment
Planning
Equipment
0~8 0 None Sector
Planning
R0A, R0B, R0C,

R0D, R0E, R0F,
R0G, R0H, R1A,
R0A None Sector
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B
0~50, step:0.1 None None N/A Sector

Normal, NoLicense None None N/A Sector
0~40 characters None None N/A Sector

0~40 characters None None N/A Sector
COMPATIBLE,
HTTPS_ONLY, Equipment WEBLOGINPOLIC
HTTPS_ONLY None
LOGIN_HTTPS_O Planning Y
NLY
Equipment
0~35 None None ALD
Planning
0~2 characters None None N/A ALD

Equipment
0~49 characters NULL None ALD
Planning
Equipment
0~62 0 None ALD
Planning
Equipment
4~5,60~254 None None ALD
Planning
Equipment
0~8 None None ALD
Planning
AISG1.1, AISG2.0,
None None N/A ALD
3GPP, UNKNOWN
0~8 None None N/A ALD
Equipment
Planning
Equipment
Planning
SINGLE_RET,
None None N/A ALD
STMA, MULTI_RET
R0A, R0B,
RET_PORT, R0C,
None None N/A ALD
R0D, R0E, R0F,
R0G, R0H, NULL
Equipment
0~62 0 None AntennaPort
Planning
Equipment
4~5,60~254 None None AntennaPort
Planning
Equipment
0~8 None None AntennaPort
Planning
R0A, R0B, R0C,

Equipment
R0D, R0E, R0F, None None AntennaPort
Planning
R0G, R0H
Equipment
Planning
Equipment
Planning
Equipment
Planning
ON, OFF OFF(OFF) None Engineering Design AntennaPort

UER_SELF_DEFIN
E,
TMA12DB_ONLY_
NON_AISG,
UER_SELF_DEFIN
TMA24DB_ONLY_
E(UER_SELF_DEF None Engineering Design AntennaPort
NON_AISG,
INE)
RET_ONLY_COAXI
AL,
TMA12DB_AISG,
TMA24DB_AISG
0~3500 40 None Engineering Design AntennaPort


0~3500 None None N/A AntennaPort
ON, OFF, NULL None None N/A AntennaPort
SINGLE_RET, Equipment
None None RET
MULTI_RET Planning
Equipment
SINGLE, DUAL None None RET
Planning
REGULAR, Equipment
None None RET
DAISY_CHAIN Planning
Equipment
1~8 1 None RET
Planning
RET, VRET None None N/A RET
Equipment
0~35 None None RET
Planning
0~2 characters None None N/A RET

Equipment
0~49 characters NULL None RET
Planning
Equipment
0~62 0 None RET
Planning
Equipment
4~5,60~254 None None RET
Planning
Equipment
0~8 None None RET
Planning
AISG1.1, AISG2.0,
None None N/A RET
3GPP, UNKNOWN
0~8 None None N/A RET
Equipment
Planning
Equipment
Planning
SINGLE_RET,
None None N/A RET
STMA, MULTI_RET
R0A, R0B,
RET_PORT, R0C,
None None N/A RET
R0D, R0E, R0F,
R0G, R0H, NULL
Equipment
0~35 None None RetDeviceData
Planning
Equipment
1~8 None None RetDeviceData
Planning
Radio Planning
0~359 0 None RetDeviceData
(Internal planning)
Equipment
0~15 characters NULL None RetDeviceData
Planning
Equipment
Planning
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
0~25.5, step:0.1 0 None RetDeviceData
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Equipment
Planning
Radio Planning
-10~30, step:0.1 0 None RetDeviceData
(Internal planning)
Equipment
Planning
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV, UNUSED(UNUSED Default/Recommen
None RetDeviceData
BandVI, BandVII, ) ded Value
BandVIII, BandIX,
BandX
UNUSED, BandI,
BandII, BandIII,
None RetDeviceData
BandVIII, BandIX,
BandX
UNUSED, BandI,
BandII, BandIII,
None RetDeviceData
BandVIII, BandIX,
BandX
UNUSED, BandI,
BandII, BandIII,
None RetDeviceData
BandVIII, BandIX,
BandX
Equipment
Planning
Equipment
Planning
-180~180, step:0.1 None None N/A RetDeviceData
-180~180, step:0.1 None None N/A RetDeviceData

UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
None None N/A RetDeviceData
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
0~359 None None N/A RetDeviceData
0~25.5, step:0.1 None None N/A RetDeviceData
Equipment
0 None None RetPort
Planning
Equipment
60~254 None None RetPort
Planning
Equipment
0 None None RetPort
Planning
Equipment
RET_PORT None None RetPort
Planning
Equipment
ON, OFF OFF(OFF) None RetPort
Planning
UER_SELF_DEFIN
UER_SELF_DEFIN
E, Default/Recommen
E(UER_SELF_DEF None RetPort
RET_ONLY_MULTI ded Value
INE)
CORE
Default/Recommen
0~3500 40 None RetPort
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
0~3500 None None N/A RetPort
ON, OFF, NULL None None N/A RetPort
Equipment
0~35 None None RETSubunit
Planning
Equipment
1~8 None None RETSubunit
Planning
AVAILABLE,
UNAVAILABLE,
None None N/A RETSubunit
BREAKLINK,
RESERVED
-10~30, step:0.1 None None N/A RETSubunit
0~17 None None N/A RETSubunit
Equipment
0~62,255 255 None RETSubunit
Planning
Equipment
4~5,60~255 255 None RETSubunit
Planning
Equipment
Planning
R0A, R0B, R0C,

Equipment
R0D, R0E, R0F, R0A(R0A) None RETSubunit
Planning
R0G, R0H
Equipment
Planning
Equipment
4~5,60~255 255 None RETSubunit
Planning
Equipment
Planning
R0A, R0B, R0C,

Equipment
R0D, R0E, R0F, R0B(R0B) None RETSubunit
Planning
R0G, R0H
Radio Planning
-10~30, step:0.1 0 None RETSubunit
(Internal planning)
Default/Recommen
0~1, step:0.1 5 None RETSubunit
ded Value
0~49 characters NULL None Engineering Design RETSubunit
Equipment
1~2 None None TMA
Planning
Equipment
0~35 None None TMA
Planning
0~2 characters None None N/A TMA

Equipment
0~49 characters NULL None TMA
Planning
Equipment
0~62 0 None TMA
Planning
Equipment
4~5,60~254 None None TMA
Planning
Equipment
0~8 None None TMA
Planning
AISG1.1, AISG2.0,
None None N/A TMA
3GPP, UNKNOWN
0~8 None None N/A TMA
Equipment
Planning
Equipment
Planning
SINGLE_RET,
None None N/A TMA
STMA, MULTI_RET
R0A, R0B,
RET_PORT, R0C,
None None N/A TMA
R0D, R0E, R0F,
R0G, R0H, NULL
Equipment
0~35 None None TMADeviceData
Planning
Equipment
1~2 None None TMADeviceData
Planning
Default/Recommen
0~359 0 None TMADeviceData
ded Value
Equipment
0~32 characters NULL None TMADeviceData
Planning
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
0~25.5, step:0.1 0 None TMADeviceData
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Equipment
Planning
Default/Recommen
-10~30, step:0.1 0 None TMADeviceData
ded Value
Equipment
Planning
UNUSED, BandI,
BandII, BandIII,
None TMADeviceData
BandVIII, BandIX,
BandX
UNUSED, BandI,
BandII, BandIII,
None TMADeviceData
BandVIII, BandIX,
BandX
UNUSED, BandI,
BandII, BandIII,
None TMADeviceData
BandVIII, BandIX,
BandX
UNUSED, BandI,
BandII, BandIII,
None TMADeviceData
BandVIII, BandIX,
BandX
Equipment
Planning
Equipment
Planning
Equipment
Planning
0~1073741823.75,
None None N/A TMADeviceData
step:0.25
0~1073741823.75,
step:0.25
UNSUPPORT,
SUPPORT_BYPAS
S,
SUPPORT_VSWR,
VSWR/BYPASS,
NULL
0~63.75, step:0.25 None None N/A TMADeviceData
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
UNUSED, BandI,
BandII, BandIII,
BandIV, BandV,
BandVI, BandVII,
BandVIII, BandIX,
BandX, NULL
0~359 None None N/A TMADeviceData

0~65535 0 None N/A TMADeviceData
Equipment
0~35 None None TMASubunit
Planning
Equipment
1~2 None None TMASubunit
Planning
0~17 None None N/A TMASubunit
0~1073741823.75,
None None N/A TMASubunit
step:0.25
NORMAL,
BYPASS, NULL
AVAILABLE,
UNAVAILABLE,
BREAKLINK,
RESERVED
R0A, R0B, R0C,

Equipment
R0D, R0E, R0F, R0A(R0A) None TMASubunit
Planning
R0G, R0H
Equipment
0~62,255 255 None TMASubunit
Planning
Equipment
0~8,255 255 None TMASubunit
Planning
Equipment
4~5,60~255 255 None TMASubunit
Planning
Radio Planning
0~63.75, step:0.25 255 None TMASubunit
(Internal planning)
NORMAL(NORMAL Default/Recommen
NORMAL, BYPASS None TMASubunit
) ded Value
Equipment
0~62 None None VAntennaPort
Planning
Equipment
60~254 None None VAntennaPort
Planning
Equipment
0 None None VAntennaPort
Planning
R0A, R0B, R1A,

R1B, R2A, R2B,
R3A, R3B, R4A, Equipment
None None VAntennaPort
R4B, R5A, R5B, Planning
R6A, R6B, R7A,
R7B, NULL
Equipment
60~254 None None VRET
Planning
Equipment
0~62 None None VRET
Planning
Equipment
60~254 None None VRET
Planning
Equipment
0 None None VRET
Planning
Equipment
0~64 characters None None VRET
Planning
Equipment
8 8 None VRET
Planning
Equipment
0~62 None None VRETSubunit
Planning
R0A, R0B, R1A,

R1B, R2A, R2B,
R3A, R3B, R4A,
NULL(NULL) None Engineering Design VRETSubunit
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B, NULL
R0A, R0B, R1A,
R1B, R2A, R2B,
R3A, R3B, R4A,
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B, NULL
Equipment
0~64 characters None None VRETSubunit
Planning
Equipment
Planning
NEGATIVE_45,
POSITIVE_45,
HORIZONTAL,
POSITIVE_NEGATI Equipment
VERTICAL, LEFT, None VRETSubunit
VE_45 Planning
RIGHT,
POSITIVE_NEGATI
VE_45
Equipment
0 None None VRETSubunit
Planning
Equipment
Planning
Equipment
Planning
R0A, R0B, R1A,
R1B, R2A, R2B,
R3A, R3B, R4A,
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B, NULL
NEGATIVE_45,
POSITIVE_45,
HORIZONTAL,
VE_45 Planning
RIGHT,
POSITIVE_NEGATI
VE_45
-15~15,3276.7,
32767 None Engineering Design VRETSubunit
step:0.1
-15~15,3276.7,
32767 None Engineering Design VRETSubunit
step:0.1
R0A, R0B, R1A,
R1B, R2A, R2B,
R3A, R3B, R4A,
R4B, R5A, R5B,
R6A, R6B, R7A,
R7B, NULL
NEGATIVE_45,
POSITIVE_45,
HORIZONTAL,
VE_45 Planning
RIGHT,
POSITIVE_NEGATI
VE_45
NEGATIVE_45,
POSITIVE_45,
HORIZONTAL,
VE_45 Planning
RIGHT,
POSITIVE_NEGATI
VE_45
Equipment
0,1,2,4 0 None VRETSubunit
Planning
Equipment
0~255 None None CTRLLNK
Planning
Equipment
Planning
Equipment
Planning
Equipment
Planning
Equipment
Planning
Equipment
Planning
Equipment
Planning
Equipment
Planning
0~4,8 None None N/A CTRLLNK
2000-01-01
00:00:00~2038-12- None None N/A CTRLLNK
31 23:59:59
0~4294967295 None None N/A CTRLLNK


0~31 characters None None N/A CTRLLNK

Default/Recommen
0 0 0 BITS
ded Value
Default/Recommen
0~7 0 0 BITS
ded Value
Default/Recommen
0~1 0 0 BITS
ded Value
Default/Recommen
0~7 0 0 BITS
ded Value
DEACTIVATED,
None None N/A BITS
ACTIVATED
UNAVAILABLE,
None None N/A BITS
AVAILABLE
Default/Recommen
1~4 4 4 BITS
ded Value
Default/Recommen
0 0 0 LineClk
ded Value
Default/Recommen
0~7 0 0 LineClk
ded Value
Default/Recommen
0~1 0 0 LineClk
ded Value
Default/Recommen
0~7 6 4 LineClk
ded Value
Equipment
0~7 0 0 LineClk
Planning
DEACTIVATED,
None None N/A LineClk
ACTIVATED
UNAVAILABLE,
None None N/A LineClk
AVAILABLE
Default/Recommen
1~4 4 4 LineClk
ded Value
Default/Recommen
0 0 0 PeerClk
ded Value
UMTS, GSM, DEFAULT(DEFAUL Default/Recommen
None PeerClk
DEFAULT T) ded Value
DEACTIVATED,
None None N/A PeerClk
ACTIVATED
UNAVAILABLE,
None None N/A PeerClk
AVAILABLE
Equipment
0~1 0 0 TOD
Planning
Default/Recommen
IN, OUT IN(Input) IN(Input) TOD
ded Value
Default/Recommen
0~7 0 0 TOD
ded Value
Default/Recommen
0~1 0 0 TOD
ded Value
Default/Recommen
0~7 0 None TOD
ded Value
TWISTED-PAIR, TWISTED- Equipment
None TOD
COAXIAL PAIR(Twisted-Pair) Planning
Equipment
0~1000 0 None TOD
Planning
DEACTIVATED,
None None N/A TOD
ACTIVATED
UNAVAILABLE,
None None N/A TOD
AVAILABLE
0~100000 None 0 N/A TOD

Default/Recommen
1~4 4 4 TOD
ded Value
Equipment
0~17 0 0 GPS
Planning
Default/Recommen
0~7 0 0 GPS
ded Value
Default/Recommen
0~1,60~254 0 0 GPS
ded Value
Default/Recommen
0~7 7 None GPS
ded Value
USER_CONFIG,
SEARCH_WITH_D
URATION, AUTO_SEARCH(A Default/Recommen
None GPS
SEARCH_WITH_P uto Search) ded Value
RECISION,
AUTO_SEARCH
-180~180, step:1e- Equipment

0 None GPS
6 Planning
Equipment
-90~90, step:1e-6 0 None GPS
Planning
Equipment
-1000~10000 0 None GPS
Planning
Equipment
0~89 5 None GPS
Planning
0~100000 None 0 N/A GPS
Default/Recommen
1~2880 1 None GPS
ded Value
Default/Recommen
1~100 1 None GPS
ded Value
TWISTED-PAIR, Equipment
COAXIAL(Coaxial) None GPS
COAXIAL Planning
Equipment
0~1000 0 None GPS
Planning
1~63 characters None None N/A GPS
Lock, Unlock None None N/A GPS
Valid, Invalid None None N/A GPS
NotFixed, Fixed None None N/A GPS

Enabled, Disabled None None N/A GPS
0~100 None None N/A GPS
NOTEXIST,
ANTENNASHORTE
D,
ANTENNAOPENE
D,
SELF_CHECK_FAI
LURE, None None N/A GPS
COMEXCEPTION,
NORMAL,
UNKNOWN,
USCUINVALID,
UNKNOWN_STAR
_CARD
M12M, UT, RT,
JPS15L, K161,
GG16, JNS100,
RGPS, CWAIN,
RTSMT, UBLOX5,
None None N/A GPS
BD7702, NAVIOR,
PPSTOD, M1000,
TRGPS,
BD7702CMS,
OEM4, UNKNOWN

GPS, GLONASS,
GPS/GLONASS,
Equipment
COMPASS, GPS(GPS) GPS(GPS) GPS
Planning
COMPASS/GPS,
GPS/COMPASS
DEACTIVATED,
None None N/A GPS
ACTIVATED
Default/Recommen
1~4 4 4 GPS
ded Value
Equipment
0~1 0 0 IPCLKLNK
Planning
HW_DEFINED, Equipment
PTP(PTP Protocol) PTP(PTP) IPCLKLNK
PTP Planning
Equipment
0~7 0 0 IPCLKLNK
Planning
Equipment
0~1 0 0 IPCLKLNK
Planning
Equipment
0~7 7 None IPCLKLNK
Planning
Equipment
Valid IP address 0.0.0.0 None IPCLKLNK
Planning
Equipment
Valid IP address 0.0.0.0 None IPCLKLNK
Planning
Equipment
0~127 0 0 IPCLKLNK
Planning
Default/Recommen
E2E, P2P E2E(E2E) E2E(E2E) IPCLKLNK
ded Value
Default/Recommen
OFF, ON ON(ON) ON IPCLKLNK
ded Value
Default/Recommen
0~255 6 6 IPCLKLNK
ded Value
Default/Recommen
0~255 13 13 IPCLKLNK
ded Value
Default/Recommen
0~255 7 7 IPCLKLNK
ded Value
Default/Recommen
0~255 14 14 IPCLKLNK
ded Value
0~4294967295 None None N/A IPCLKLNK
Default/Recommen
NO, YES NO(NO) NO(NO) IPCLKLNK
ded Value
Default/Recommen
14 characters 0000-0000-0000 None IPCLKLNK
ded Value
DEACTIVATED,
None None N/A IPCLKLNK
ACTIVATED
UNAVAILABLE,
AVAILABLE
UNICAST, Default/Recommen
UNICAST(Unicast) UNICAST(Unicast) IPCLKLNK
L2_MULTICAST ded Value
Default/Recommen
-100000~100000 0 0 IPCLKLNK
ded Value
ONE_STEP,
TWO_STEP
-
483647
Default/Recommen
1~4 4 4 IPCLKLNK
ded Value
1/16, 1/8, 1/4, 1/2, Default/Recommen

1/2(1/2) None IPCLKLNK
1.0, 2.0, 4.0, 8.0 ded Value
1/2, 1.0, 2.0, 4.0,

Default/Recommen
8.0, 16.0, 32.0, 16.0(16.0) None IPCLKLNK
ded Value
64.0, 128.0
Default/Recommen
0~255 255 None IPCLKLNK
ded Value
Default/Recommen
1588V2, G.8265.1 1588V2(1588V2) None IPCLKLNK
ded Value
Default/Recommen
60~1000 300 None IPCLKLNK
ded Value
Default/Recommen
IPV4, IPV6 IPV4(IPv4) None IPCLKLNK
ded Value
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal IPCLKLNK
planning)
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal IPCLKLNK
planning)
Default/Recommen
0 0 0 SyncEth
ded Value
Default/Recommen
0~7 0 0 SyncEth
ded Value
Default/Recommen
0~1 0 0 SyncEth
ded Value
Default/Recommen
0~7 7 None SyncEth
ded Value
Equipment
0~5 0 0 SyncEth
Planning
DISABLE(DISABLE Equipment
DISABLE, ENABLE None SyncEth
) Planning
DEACTIVATED,
None None N/A SyncEth
ACTIVATED
UNAVAILABLE,
None None N/A SyncEth
AVAILABLE
Default/Recommen
1~4 4 4 SyncEth
ded Value
AVAILABLE,
UNAVAILABLE,
None None N/A Tasm
UNSUPPORT,
PARTAVAILABLE
FORBID, ALLOW,
None None N/A Tasm
NA
1~4 None None N/A Tasm
0, 1, 2, 3, 4, 5, 6, 7,
8, 9, 10, 11, 12, 13, Equipment
0(0) None Tasm
14, 15, 16, 17, Planning
AUTO
GPS, BITS, IPCLK,
SYNCETH,
LINECLK, TOD, Equipment
GPS(GPS Clock) GPS(GPS Clock) Tasm
PEERCLK, Planning
SYNCETH+IPCLK,
GPS+SYNCETH
AUTO, MANUAL, Default/Recommen

AUTO(Auto) AUTO(Auto) Tasm
FREE ded Value
Default/Recommen
FREQ, TIME FREQ(FREQ) None Tasm
ded Value
NORMAL, LOST,
UNAVAILABLE,
FREDVAT, JITTER,
None None N/A Tasm
PHASEOUTSCOP
E, UNKNOWN,
DIFFSRC
FREERUNNING,
FASTTRACKING,
LOCKED, None None N/A Tasm
HOLDOVER,
UNKNOWN
GPS, BITS, IPCLK,

SYNCETH,
LINECLK, TOD,
None None N/A Tasm
PEERCLK,
SYNCETH+IPCLK,
GPS+SYNCETH
0~7 None 0 N/A Tasm
0~1 None 0 N/A Tasm
0~7 None None N/A Tasm

QL-PRC, QL-SSU-
A, QL-SSU-B, QL- QL-SSU-B(QL- Default/Recommen
None Tasm
EEC2, QL-EEC1, SSU-B) ded Value
QL-DNU
Equipment
0~7 0 None BBP
Planning
Equipment
0~1 0 None BBP
Planning
Equipment
0~5 None None BBP
Planning
Equipment
LBBP LBBP(LBBP) LBBP(LBBP) BBP
Planning
FDD, TDD,
TDD_ENHANCE, FDD(Frequency FDD(Frequency Radio Planning
BBP
TDD_8T8R, Division Duplex) Division Duplex) (Internal planning)
TDD_TL
BLOCKED, UNBLOCKED(Unbl UNLOCKED(Unlock

Engineering Design BBP
UNBLOCKED ocked) ed)
0~4294967295 0 0 Engineering Design BBP

IMMEDIATE, IMMEDIATE(Immed IMMEDIATE(Immed
Engineering Design BBP
DELAY iate) iate)
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A BBP
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A BBP

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A BBP
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A BBP

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A BBP
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A BBP
CPU, DSP,
SLAVE_CPU,
None None N/A BBP
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A BBP
483647
-
2147483648~2147 None None N/A BBP
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A BBP
EDL, Slave
CABINET,
SUBRACK,
None None N/A BBP
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A BBP
Timeout, NULL
Equipment
0~7 0 None BbuFan
Planning
Equipment
0~1 0 None BbuFan
Planning
Equipment
16 None None BbuFan
Planning
-
2147483648~2147 None None N/A BbuFan
483647
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A BbuFan
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A BbuFan

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A BbuFan
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A BbuFan

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
MDU_CPU,
MRU_CPU
-
483647
-
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A BbuFan
EDL, Slave
CABINET,
SUBRACK,
BOARD,
SUBBOARD, SFP
Normal, Fault,
Timeout, NULL
Equipment
0~62 None None CCU
Planning
Radio Planning
15 15 15 CCU
(Internal planning)
Radio Planning
0 0 0 CCU
(Internal planning)
Equipment
0~62 0 None CCU
Planning
Equipment
0~1 0 None CCU
Planning
Equipment
0~1 0 0 CCU
Planning
Based on the Equipment

NO, YES YES(YES) CCU
physical connection Planning
Equipment
1~7 None None CCU
Planning
GSM:NO, Based on the Equipment

GSM, UMTS, LTE CCU
UMTS:NO, LTE:NO physical connection Planning
It is recommended
Water-Immersed that Water-
Sensor Immersed Sensor
WS_DISABLE, Equipment
Disabled:ON, Smog Disabled be set to CCU
SS_DISABLE Planning
Sensor ON, Smog Sensor
Disabled:ON Disabled be set to
ON.
CONNECTED,
None None N/A CCU
DISCONNECTED
CONNECTED,
None None N/A CCU
DISCONNECTED
0~4294967295 None None N/A CCU
Default/Recommen
0~249 0 None CPRILBR
ded Value
LBR0, LBR1, LBR2,
LBR3, LBR4, LBR5, None None N/A CPRILBR
LBR6
NEGOTIATED,
NEGOTIATING,
NOTREADY, None None N/A CPRILBR
TIMEOUT,
USERCONFIG
LBR0, LBR1, LBR2,

LBR6
NEGOTIATED,
NEGOTIATING,
NOTREADY, None None N/A CPRILBR
TIMEOUT,
USERCONFIG
0~62 None None N/A CPRILBR
HEAD, TAIL None None N/A CPRILBR

LBR0, LBR1, LBR2,
LBR6
Equipment
0~62 0 None CpriPort
Planning
Equipment
0~1,4~5,60~254 0 None CpriPort
Planning
Equipment
0~8 None None CpriPort
Planning
Equipment
0~5 None None CpriPort
Planning
614M, 1.25G, 2.5G,
4.9G, 6.1G, 9.8G, None None N/A CpriPort
UNKNOWN, NULL
BLOCKED,
UNBLOCKED,
None None N/A CpriPort
SHUTINGDOWN,
INVALID
INPOSITION,
NOTINPOSITION, None None N/A CpriPort
INVALID
Slave, Master,
NULL
SFP_OPTICAL,
ESFP_OPTICAL,
SFP_ELECTRIC,
SCSI_ELECTRIC,
GE, UNKNOWN,
NULL
0~4294967295 None None N/A CpriPort

CPRI_MUX,
NORMAL, None None N/A CpriPort
UNKNOWN, NULL
Equipment
DC, AC DC(DC) None ENERGYCON
Planning
Equipment
0~7 0 None MPT
Planning
Equipment
0~1 0 None MPT
Planning
Equipment
6~7 None None MPT
Planning
Equipment
UMPT, LMPT None None MPT
Planning
Unknown, NULL,
None None N/A MPT
Active, Standby
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A MPT
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A MPT

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A MPT
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A MPT

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A MPT
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A MPT
CPU, DSP,
SLAVE_CPU,
None None N/A MPT
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A MPT
483647
-
2147483648~2147 None None N/A MPT
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A MPT
EDL, Slave
CABINET,
SUBRACK,
None None N/A MPT
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A MPT
Timeout, NULL
Equipment
0~7 0 None PEU
Planning
Equipment
0~1 0 None PEU
Planning
Equipment
18~19 None None PEU
Planning
NULL None None N/A PEU
NULL None None N/A PEU

Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A PEU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A PEU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A PEU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A PEU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A PEU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A PEU
CPU, DSP,
SLAVE_CPU,
None None N/A PEU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A PEU
483647
-
2147483648~2147 None None N/A PEU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A PEU
EDL, Slave
CABINET,
SUBRACK,
None None N/A PEU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A PEU
Timeout, NULL
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Engineering Design PSUIS
Equipment
0~62 None None SFP
Planning
Equipment
0~1,4~5,60~254 None None SFP
Planning
Equipment
0~8 None None SFP
Planning
Equipment
0~8 None None SFP
Planning
INPOSITION,
NOTINPOSITION, None None N/A SFP
INVALID
SFP, ESFP,
SFP_ELECTRIC,
None None N/A SFP
QSFP, EQSFP,
UNKNOWN
0~15 characters None None N/A SFP
SINGLEMODE,
MULTIMODE, None None N/A SFP
UNKNOWN
0~65535 None None N/A SFP
0~25500, step:100 None None N/A SFP


-128~128, step:0.1 None None N/A SFP
0~6553500,
None None N/A SFP
step:100
0~6553.5, step:0.1 None None N/A SFP
0~6553.5, step:0.1 None None N/A SFP
Equipment
0~7 0 None TRP
Planning
Equipment
0~1 0 None TRP
Planning
Equipment
0~6 None None TRP
Planning
Equipment
UIEB, UTRPc None None TRP
Planning
Unknown, NULL,
None None N/A TRP
Active, Standby
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A TRP
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A TRP

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A TRP
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A TRP

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A TRP
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A TRP
CPU, DSP,
SLAVE_CPU,
None None N/A TRP
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A TRP
483647
-
2147483648~2147 None None N/A TRP
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A TRP
EDL, Slave
CABINET,
SUBRACK,
None None N/A TRP
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A TRP
Timeout, NULL
Equipment
0~7 None None UCIU
Planning
Equipment
0~1 None None UCIU
Planning
Equipment
0~7 None None UCIU
Planning
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A UCIU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A UCIU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A UCIU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A UCIU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A UCIU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A UCIU
CPU, DSP,
SLAVE_CPU,
None None N/A UCIU
MDU_CPU,
MRU_CPU
-
483647
-
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A UCIU
EDL, Slave
CABINET,
SUBRACK,
None None N/A UCIU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A UCIU
Timeout, NULL
Equipment
0~7 0 None UEIU
Planning
Equipment
0~1 0 None UEIU
Planning
Equipment
18~19 None None UEIU
Planning
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A UEIU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A UEIU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A UEIU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A UEIU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A UEIU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A UEIU
CPU, DSP,
SLAVE_CPU,
None None N/A UEIU
MDU_CPU,
MRU_CPU
-
483647
-
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A UEIU
EDL, Slave
CABINET,
SUBRACK,
None None N/A UEIU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A UEIU
Timeout, NULL
Equipment
0~7 0 None USCU
Planning
Equipment
0~1 0 None USCU
Planning
Equipment
0~5 None None USCU
Planning
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A USCU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A USCU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A USCU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A USCU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A USCU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A USCU
CPU, DSP,
SLAVE_CPU,
None None N/A USCU
MDU_CPU,
MRU_CPU
-
483647
-
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A USCU
EDL, Slave
CABINET,
SUBRACK,
None None N/A USCU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A USCU
Timeout, NULL
Equipment
0~64 characters NULL None Equipment
Planning
ON, OFF OFF(OFF) None Engineering Design Equipment

ON, OFF OFF(OFF) None Engineering Design Equipment
NORMAL,
INSTALL, EXPAND,
UPGRADE,
TESTING,
ExpandStatus1,
ExpandStatus2,
ExpandStatus3, NORMAL(NORMAL
None Engineering Design Equipment
ExpandStatus4, )
ExpandStatus5,
ExpandStatus6,
ExpandStatus7,
ExpandStatus8,
ExpandStatus9,
ExpandStatus10
2000-01-
01T00:00:00+00:00 2000-01-
~2037-12- 01T00:00:00+00:00
31T23:59:59+00:00
2000-01-
01T00:00:00+00:00 2037-12-
~2037-12- 31T23:59:59+00:00
31T23:59:59+00:00
0~255 characters None None Engineering Design Equipment
NORMAL,
INSTALL, EXPAND,
UPGRADE,
TESTING,
ExpandStatus1,
ExpandStatus2,
ExpandStatus3,
None None N/A Equipment
ExpandStatus4,
ExpandStatus5,
ExpandStatus6,
ExpandStatus7,
ExpandStatus8,
ExpandStatus9,
ExpandStatus10
Equipment
DISABLE, ENABLE DISABLE(Disable) None Equipment
Planning
Equipment
39.0~48.0, step:0.1 450 None Equipment
Planning
Equipment
39.0~60.0, step:0.1 455 None Equipment
Planning
Equipment
0~62 None None Cabinet
Planning
APM30, TMC, BBC,
PS4890, OMB,
RFC, BTS3900,
VIRTUAL(Virtual Equipment
BTS3900L, None Cabinet
Cabinet) Planning
BTS3900AL,
VIRTUAL,
TP48600A, ILC29
Equipment
0~79 characters NULL None Cabinet
Planning
0~31 characters None None N/A Cabinet

Equipment
0~62 None None Subrack
Planning
Equipment
0~254 None None Subrack
Planning
BBU3900, RFU,
PMU, TCU, FMU, Equipment
None None Subrack
RRU, EMU, PICO, Planning
CCU, UNKNOW
0~79 characters NULL None Engineering Design Subrack
AC220V, DC-48V,
DC+28V, DC+24V,
DC-48V-2, AC110V, None None N/A Subrack
RDC-48V, NDC-
48V
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A RU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A RU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A RU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A RU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A RU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A RU
CPU, DSP,
SLAVE_CPU,
None None N/A RU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A RU
483647
-
2147483648~2147 None None N/A RU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A RU
EDL, Slave
CABINET,
SUBRACK,
None None N/A RU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A RU
Timeout, NULL
Default/Recommen
0~62 0 0 EMU
ded Value
Default/Recommen
40~59 40 40 EMU
ded Value
Default/Recommen
0 0 0 EMU
ded Value
Default/Recommen
0~62 0 0 EMU
ded Value
Default/Recommen
0~254 0 0 EMU
ded Value
When the EMU is

connected to the
MON1 port on the
UPEU, set this
parameter to 1.
When the EMU is
connected to the
MON0 port on the
UPEU, set this Default/Recommen
0~7 None EMU
parameter to 0. ded Value
When the EMU is
connected to the
RRU, set this
parameter to
0.When the EMU is
connected to the
CCU, set this
parameter to 0~7.
Default/Recommen
1~30 2 2 EMU
ded Value
Default/Recommen
-20~80 0 0 EMU
ded Value
Default/Recommen
-20~80 50 50 EMU
ded Value
Default/Recommen
0~100 10 10 EMU
ded Value
Default/Recommen
0~100 80 80 EMU
ded Value
It is recommended
that -48 Voltage
-48 Voltage Disabled be set to
Disabled:OFF, OFF, Reserved
Reserved Sensor Sensor 0 be set to
48V_DISABLE, 0:ON, Reserved ON, Reserved
RES0, RES1, Sensor 1:ON, Sensor 1 be set to
Equipment
RES2, Reserved Sensor ON, Reserved EMU
Planning
TS_DISABLE, 2:ON, Temperature Sensor 2 be set to
HS_DISABLE Sensor ON, Temperature
Disabled:OFF, Sensor Disabled be
Humidity Sensor set to OFF, and
Disabled:OFF Humidity Sensor
Disabled be set to
OFF.
It is recommended
that Water-
Water -Immersed
Immersed Sensor
Sensor
Disabled be set to
Disabled:OFF,
WS_DISABLE, OFF, Smog Sensor
Smog Sensor
SS_DISABLE, Disabled be set to Equipment
Disabled:OFF, EMU
IS_DISABLE, OFF, Infrared Planning
Infrared Sensor
GS_DISABLE Sensor Disabled be
Disabled:ON,
set to ON, and
Gating Sensor
Gating Sensor
Disabled:OFF
Disabled be set to
OFF.
-
2147483648~2147 None None N/A EMU
483647
0~100 None None N/A EMU
0.0~100.0 None None N/A EMU

-999.99~9999.99 None None N/A EMU
-999.99~9999.99 None None N/A EMU
-999.99~9999.99 None None N/A EMU
-999.99~9999.99 None None N/A EMU
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A EMU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A EMU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A EMU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A EMU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A EMU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
None None N/A EMU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A EMU
483647
-
2147483648~2147 None None N/A EMU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A EMU
EDL, Slave
CABINET,
SUBRACK,
None None N/A EMU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A EMU
Timeout, NULL
Default/Recommen
0~62 0 0 FMU
ded Value
Default/Recommen
11~12 11 11 FMU
ded Value
Default/Recommen
0 0 0 FMU
ded Value
Default/Recommen
0~62 0 0 FMU
ded Value
Default/Recommen
0~254 0 0 FMU
ded Value
When the FMU is

connected to the
MON1 port on the
UPEU, set this
parameter to 1.
When the FMU is
connected to the
MON0 port on the
UPEU, set this
parameter to 0. Default/Recommen
0~7 None FMU
When the FMU is ded Value
connected to the
RRU, set this
parameter to 0.
When the FMU is
connected to the
CCU, set this
parameter to a
value within the
range of 0 to 7.
The FMUs of a
maximum of two
levels can be
connected to a bus.
The communication
address of the FMU
Default/Recommen
1~30 14 that is directly FMU
ded Value
connected to the
BBU is set to 14.
The communication
address of the
lower-level FMU is
set to 15.
Water-Immersed Water-Immersed
Sensor Sensor
WS_DISABLE, Default/Recommen
Disabled:ON, Smog Disabled:ON, Smog FMU
SS_DISABLE ded Value
Sensor Sensor
Disabled:ON Disabled:ON
0~100 None None N/A FMU
-127~127 None None N/A FMU
-127~127 None None N/A FMU
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Engineering Design FMU

0~65535 0 0(Default Mode) Engineering Design FMU
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A FMU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A FMU
Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A FMU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A FMU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A FMU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU

CPU, DSP,
SLAVE_CPU,
None None N/A FMU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A FMU
483647
-
2147483648~2147 None None N/A FMU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A FMU
EDL, Slave
CABINET,
SUBRACK,
None None N/A FMU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A FMU
Timeout, NULL
Default/Recommen
0~62 0 0 TCU
ded Value
Default/Recommen
8,14 8 8 TCU
ded Value
Default/Recommen
0~3 0 0 TCU
ded Value
Default/Recommen
0~62 0 0 TCU
ded Value
Default/Recommen
0~254 0 0 TCU
ded Value
When the TCU is

connected to the
MON1 port on the
UPEU, set this
parameter to 1.
When the TCU is
connected to the
MON0 port on the
UPEU, set this
0~7 None TCU
When the TCU is ded Value
connected to the
RRU, set this
parameter to 0.
When the TCU is
connected to the
CCU, set this
parameter to a
value within the
range of 0 to 7.
used for heat
dissipation be set to
6 or 7 and that of
the TCU used for
heating be set to 28
or 29.
If the manager unit
of the TCU is a
BBU and the TCU
is not configured in
a BBC, it is
recommended that
the communication
address of the TCU
used for heat
dissipation be set to
6 or 7 and that of
the TCU used for
Default/Recommen
1~30 7 heating be set to 28 TCU
ded Value
or 29. For the TCU
configured in a
BBC, if the
communication
address of the PMU
connected to the
BBC is 3, the
communication
address of the
level-1 TCU
connected to the
BBU is set to 23
and that of the
level-2 TCU is set
to 24. If the
communication
address of the PMU
connected to the
Default/Recommen
-40~10 -20 -20 TCU
ded Value
For the TCU in the

BBC, the
recommended
value is 50. For the Default/Recommen
20~80 68 TCU
TCU in another ded Value
cabinet, the
recommended
value is 68.
Water-Immersed Water-Immersed
Sensor Sensor
WS_DISABLE, Default/Recommen
Disabled:ON, Smog Disabled:ON, Smog TCU
SS_DISABLE ded Value
Sensor Sensor
Disabled:ON Disabled:ON
0~3 characters None None N/A TCU
-127~127 None None N/A TCU
0~4294967295 None None N/A TCU

dantherm, bw,
huawei, air-sys,
senguang,
viasystems, rittal,
emerson, APW,
hytems, hontech, None None N/A TCU
agisson, pantair,
Panasonic, Gore,
Flex, Vapel, AVC,
JIAYI, Delta, EBM,
Protechnic, Sanyo
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A TCU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A TCU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A TCU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A TCU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
None None N/A TCU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A TCU
483647
-
2147483648~2147 None None N/A TCU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A TCU
EDL, Slave
CABINET,
SUBRACK,
None None N/A TCU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A TCU
Timeout, NULL
Default/Recommen
0~62 0 0 HtCDPa
ded Value
Default/Recommen
8,14 8 8 HtCDPa
ded Value
Default/Recommen
0~3 0 0 HtCDPa
ded Value
Default/Recommen
-99~70 0 0 HtCDPa
ded Value
Default/Recommen
-99~70 40 40 HtCDPa
ded Value
Default/Recommen
-99~70 45 45 HtCDPa
ded Value
Default/Recommen
0~30 2 2 HtCDPa
ded Value
Default/Recommen
0~30 9 9 HtCDPa
ded Value
Default/Recommen
0~30 16 16 HtCDPa
ded Value
Default/Recommen
0~30 13 13 HtCDPa
ded Value
Default/Recommen
0~62 0 0 PMU
ded Value
Default/Recommen
7 7 7 PMU
ded Value
Default/Recommen
0 0 0 PMU
ded Value
Default/Recommen
0~62 0 0 PMU
ded Value
Default/Recommen
0~254 0 0 PMU
ded Value
When the PMU is

connected to the
MON1 port on the
UPEU, set this
parameter to 1.
When the PMU is
connected to the
MON0 port on the
UPEU, set this
0~7 None PMU
When the PMU is ded Value
connected to the
RRU, set this
parameter to 0.
When the PMU is
connected to the
CCU, set this
parameter to a
value within the
range of 0 to 7.
Default/Recommen
1~30 3 3 PMU
ded Value
APM100, APM200,
APM30, EPS4890,
EPS4815, Equipment
APM30(APM 30) APM30(APM 30) PMU
SC48200, Planning
EPS48200,
TP48300A, ETP
Default/Recommen
60~300 180 180 PMU
ded Value
Default/Recommen
60~300 280 280 PMU
ded Value
The recommended
value of this
parameter for the
SC48200 PMU is
470. The Default/Recommen
35.0~55.6, step:0.1 450 PMU
recommended ded Value
value of this
parameter for other
types of PMU is
450.
The recommended
value of this
parameter for the
SC48200 PMU is
58.0~60.0, step:0.1 580 PMU
value of this
parameter for other
types of PMU is
580.
The recommended
value of this
parameter for the
SC48200 PMU is
ENABLE(Enable). Default/Recommen
DISABLE, ENABLE DISABLE(Disable) PMU
The recommended ded Value
value of this
parameter for other
types of PMU is
DISABLE(Disable).
The recommended
value of this
parameter for the
SC48200 PMU is
35.0~55.6, step:0.1 440 PMU
value of this
parameter for other
types of PMU is
440.
Default/Recommen
-20~20 0 0 PMU
ded Value
Default/Recommen
35~80 50 50 PMU
ded Value
Default/Recommen
0~50 10 10 PMU
ded Value
Default/Recommen
50~100 80 80 PMU
ded Value
It is recommended
that Battery
Temperature
Sensor 1 Disabled
Battery be set to OFF for
Temperature PMUs in the
Sensor 1 APM30, PS4890,
Disabled:OFF, and SC48200 and
Cabinet Humidity ON for other PMUs,
Sensor Cabinet Humidity
BT1_DISABLE,
Disabled:ON, Sensor Disabled be
AH_DISABLE, Default/Recommen
Cabinet set to ON, Cabinet PMU
AT1_DISABLE, ded Value
Temperature Temperature
BT2_DISABLE
Sensor 1 Sensor 1 Disabled
Disabled:ON, be set to OFF for
Battery PMUs in the
Temperature APM100 and
Sensor 2 APM200 and ON
Disabled:ON for other PMUs,
and Battery
Temperature
Sensor 2 Disabled
be set to ON.
It is recommended
that Water-
Immersed Sensor
Water-Immersed Disabled be set to
Sensor ON, Smog Sensor
WS_DISABLE, Disabled:ON, Smog Disabled be set to
Default/Recommen
SS_DISABLE, Sensor ON, and Gating PMU
ded Value
GS_DISABLE Disabled:ON, Sensor Disabled be
Gating Sensor set to OFF for
Disabled:OFF PMUs in the
APM30, APM100,
and APM200 and
ON for other PMUs.
-
2147483648~2147 None None N/A PMU
483647
-100.0~100.0 None None N/A PMU
-
2147483648~2147 None None N/A PMU
483647
0~100 None None N/A PMU
PowerOn,
LowVoltagePowerO
ff,
MasterControlPowe
rOff, None None N/A PMU
HighTemperaturePo
werOff,
LowTemperaturePo
werOff
BoostCharging,
FloatCharging,
ForceBoostChargin None None N/A PMU
g, Discharging,
Sleeping
CurrentLimiting,
None None N/A PMU
NoCurrentLimiting
PowerOn,
LowVoltagePowerO
ff,
MasterControlPowe
None None N/A PMU
rOff,
ManualPowerOff,
HighTemperaturePo
werOff
-
2147483648~2147 None None N/A PMU
483647
CHARGE,
DISCHARGE, REC, None None N/A PMU
END
-
2147483648~2147 None None N/A PMU
483647
0~18 characters None None N/A PMU

Huawei, Emerson,
Holdluck-ZYT,
Power-One, Kehua,
DeltaElectronics,
EltekEnergy,
Switchtec,
TycoElectronics,
ARTESYN, None None N/A PMU
CHROMA,
LuckyValley,
ACBEL, Zippy,
GuoyaoElectronics,
DPC, GoldPower,
SungrowPowerSup
ply, Ecom
UNSUPPORTED,
None None N/A PMU
SUPPORTED
DISABLE, ENABLE None None N/A PMU

SUCCEEDED,
BRDNOTREADY,
UNSUPPORTED, None None N/A PMU
BATNOTEXIST,
INTERNALERR
UNSUPPORTED,
None None N/A PMU
SUPPORTED
DISABLE, ENABLE None None N/A PMU

Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A PMU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A PMU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A PMU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A PMU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
None None N/A PMU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A PMU
483647
-
2147483648~2147 None None N/A PMU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A PMU
EDL, Slave
CABINET,
SUBRACK,
None None N/A PMU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A PMU
Timeout, NULL
Default/Recommen
0~62 0 0 DieselGen
ded Value
Default/Recommen
7 7 7 DieselGen
ded Value
Default/Recommen
0 0 0 DieselGen
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) DieselGen
ded Value
Default/Recommen
0.1~100.0, step:0.1 125 125 DieselGen
ded Value
1~7 characters None None N/A DieselGen
-150.0~150.0 None None N/A DieselGen
0~4294967295 None None N/A DieselGen
Default/Recommen
0~62 0 0 Battery
ded Value
Default/Recommen
7 7 7 Battery
ded Value
Default/Recommen
0 0 0 Battery
ded Value
The battery
installation type of
the SC48200 PMU
is OUTER. The
Equipment
INNER, OUTER INNER(Inner) battery installation Battery
Planning
type of other types
of PMU should be
set based on the
actual situation.
Default/Recommen
30~240 60 60 Battery
ded Value
Default/Recommen
43.3~57.6, step:0.1 565 565 Battery
ded Value
Based on the PMU
type: The
recommended
value for the
APM30 is 30. The
recommended
value for the
APM100 is 100.
The recommended
value for the
5~5000 36 Engineering Design Battery
APM200 is 200.
The recommended
value for the
PS4890 is 30. The
recommended
value for the
EPS4815 is 65. The
recommended
value for the
SC48200 is 1000.
0.05~0.25, Default/Recommen
15 15 Battery
step:0.01 ded Value
Default/Recommen
43.2~57.5, step:0.1 535 535 Battery
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Battery
ded Value
The recommended
value of this
parameter for the
SC48200 PMU is
Default/Recommen
40~70 53 60. The Battery
ded Value
recommended
value of this
parameter for other
types of PMU is 53.
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Battery
ded Value
The recommended
value of this
parameter for the
SC48200 PMU is
35.0~55.6, step:0.1 430 Battery
value of this
parameter for other
types of PMU is
430.
Default/Recommen
0~500 80 80 Battery
ded Value
Default/Recommen
-20~20 -19 -19 Battery
ded Value
Default/Recommen
35~80 50 50 Battery
ded Value
1~2 1 1 Engineering Design Battery
VRLA_BAT(VRLA VRLA_BAT(VRLA
VRLA_BAT, LI_BAT Engineering Design Battery
Battery) Battery)
0~4294967295 None None N/A Battery



2000-01-01~2099-
None None N/A Battery
12-31
Based on the PMU
type: The
recommended
value for the
APM30 is 30. The
recommended
value for the
APM100 is 100.
The recommended
value for the
5~5000 36 Engineering Design Battery
APM200 is 200.
The recommended
value for the
PS4890 is 30. The
recommended
value for the
EPS4815 is 65. The
recommended
value for the
SC48200 is 1000.
Default/Recommen
0~62 0 0 BatCTPa
ded Value
Default/Recommen
7 7 7 BatCTPa
ded Value
Default/Recommen
0 0 0 BatCTPa
ded Value
1200 1200 BatCTPa
step:0.01 ded Value
600 600 BatCTPa
step:0.01 ded Value
300 300 BatCTPa
step:0.01 ded Value
150 150 BatCTPa
step:0.01 ded Value
100 100 BatCTPa
step:0.01 ded Value
70 70 BatCTPa
step:0.01 ded Value
50 50 BatCTPa
step:0.01 ded Value
40 40 BatCTPa
step:0.01 ded Value
30 30 BatCTPa
step:0.01 ded Value
25 25 BatCTPa
step:0.01 ded Value
Default/Recommen
80~100 80 80 BatCTPa
ded Value
190 190 BatCTPa
step:0.01 ded Value
Default/Recommen
1~50 24 24 BatCTPa
ded Value
Default/Recommen
1~100 10 10 BatCTPa
ded Value
Default/Recommen
1~240 60 60 BatCTPa
ded Value
Default/Recommen
40.0~54.0, step:0.1 450 450 BatCTPa
ded Value
NOAUTOTEST,
PERIOD,
POWERCUT(Powe POWERCUT(Powe Default/Recommen
POWERCUT, BatCTPa
r Off Auto Test) r Off Auto Test) ded Value
PERIODPOWERC
UT
Default/Recommen
30~240 120 120 BatCTPa
ded Value
Default/Recommen
1~60 14 14 BatCTPa
ded Value
STANDARD,
SIMPLE, TIMER, None None N/A BatCTPa
PWROFF, NONE
2000-01-01
00:00:00~2038-12- None None N/A BatCTPa
31 23:59:59
BelowEndVol,
OverTime,
CurrRecover, None None N/A BatCTPa
ManualEnd,
AlmEnd
None, Normal,
None None N/A BatCTPa
PreAlm, Alm
0~100 None None N/A BatCTPa
1~7 characters None None N/A BatCTPa
-100.00~100.00 None None N/A BatCTPa
-150.0~150.0 None None N/A BatCTPa
-
483647
Default/Recommen
0~62 0 0 PSU
ded Value
Default/Recommen
7 7 7 PSU
ded Value
Default/Recommen
1~7 1 None PSU
ded Value
NORMAL,
COMMUNICATEFAI
LED, SHUTDOWN,
None None N/A PSU
FAULT, PROTECT,
UNCONFIGURED,
ILLEGAL
0~18 characters None None N/A PSU

Huawei, Emerson,
Holdluck-ZYT,
Power-One, Kehua,
DeltaElectronics,
EltekEnergy,
Switchtec,
TycoElectronics,
ARTESYN, None None N/A PSU
CHROMA,
LuckyValley,
ACBEL, Zippy,
GuoyaoElectronics,
DPC, GoldPower,
SungrowPowerSup
ply, Ecom
0~4294967295 None None N/A PSU

Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A PSU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A PSU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A PSU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A PSU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
None None N/A PSU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A PSU
483647
-
2147483648~2147 None None N/A PSU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A PSU
EDL, Slave
CABINET,
SUBRACK,
None None N/A PSU
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A PSU
Timeout, NULL
0~62 0 0 Engineering Design OutPort
40~59 40 40 Engineering Design OutPort
0 0 0 Engineering Design OutPort
0~5 None None Engineering Design OutPort
0~50 characters NULL None Engineering Design OutPort

OFF, ON OFF(Off) OFF(Off) Engineering Design OutPort
0~62 None None Engineering Design AlmPort
0~1,7~8,11~12,14~
None None Engineering Design AlmPort
15,40~254
0~3,18~19 None None Engineering Design AlmPort
0~35 None None Engineering Design AlmPort
Equipment
OFF, ON OFF(Off) OFF(Off) AlmPort
Planning
Equipment
65033~65233 65033 65033 AlmPort
Planning
Equipment
BOOL, VALUE BOOL(Digital Port) BOOL(Digital Port) AlmPort
Planning
Equipment
HIGH, LOW LOW(Low Voltage) LOW(Low Voltage) AlmPort
Planning
-999.99~9999.99, Equipment
9900 9900 AlmPort
step:0.01 Planning
-999.99~9999.99, Equipment
100 100 AlmPort
step:0.01 Planning
VOLTAGE, VOLTAGE(Voltage VOLTAGE(Voltage Equipment

AlmPort
CURRENT Type) Type) Planning
-999.99~9999.99, Equipment
10000 10000 AlmPort
step:0.01 Planning
-999.99~9999.99, Equipment
0 0 AlmPort
step:0.01 Planning
0~9999.99, Equipment
100 100 AlmPort
step:0.01 Planning
0~9999.99, Equipment
0 0 AlmPort
step:0.01 Planning
Default/Recommen
ALL, SSL ALL(All Type) None SSL
ded Value
Default/Recommen
NONE, PEER NONE(Verify None) None SSL
ded Value
Equipment
0~62 None None AAU
Planning
Equipment
60~254 None None AAU
Planning
Equipment
0 None None AAU
Planning
Equipment
0~31 characters NULL None AAU
Planning
Equipment
MAAU None None AAU
Planning

Engineering Design AAU
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A AAU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A AAU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A AAU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A AAU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A AAU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A AAU
CPU, DSP,
SLAVE_CPU,
None None N/A AAU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A AAU
483647
-
2147483648~2147 None None N/A AAU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A AAU
EDL, Slave
CABINET,
SUBRACK,
None None N/A AAU
BOARD,
SUBBOARD, SFP
ON, OFF ON(ON) ON Engineering Design AAU
1.5~10, step:0.1 30 None Engineering Design AAU

1.5~3, step:0.1 20 None Engineering Design AAU
Equipment
0~7 None None AAU
Planning
Equipment
0~249 None None AAU
Planning
Equipment
TRUNK TRUNK(TRUNK) TRUNK AAU
Planning
TD_SCDMA,
LTE_TDD,
TDS_TDL,
LTE_FDD,
Equipment
WiMAX_LTE, None None AAU
Planning
CDMA_LTE,
GSM_LTE,
UMTS_ONLY,
UMTS_LTE
Equipment
0~8 None None AAU
Planning
Equipment
0~8 None None AAU
Planning
0~429496729.5,
None None N/A AAU
step:0.1
0~429496729.5,
None None N/A AAU
step:0.1
0~429496729.5,
None None N/A AAU
step:0.1
0~429496729.5,
None None N/A AAU
step:0.1
0~50, step:0.1 None None N/A AAU
0~6553.5, step:0.1 None None N/A AAU
-100~200 None None N/A AAU
-100~200 None None N/A AAU

LO_TD, TL, LO,
WO, WL, C0, CL,
CW, CWL, GO, GL,
GW, GWL, GC,
GCL, GCW, GCWL,
UO, UL, UW, UWL,
None None N/A AAU
UC, UCL, UCW,
UCWL, GU, UGL,
UGW, UGWL,
UGC, UGCL,
UGCW, UGCWL,
NULL
CONNECTHEAD,
CONNECTTAIL,
CONNECTBOTH, None None N/A AAU
SEPERATEBYBRE
AK, LINKDOWN
0~429496729.5,
None None N/A AAU
step:0.1
0~429496729.5,
None None N/A AAU
step:0.1

ON, OFF OFF(OFF) ON(ON) N/A AAU
1~60 1 1 N/A AAU
POW_IQ_MODE,
POW_IQ_MODE(P
POW_MODE, None N/A AAU
OW_IQ_MODE)
IQ_MODE
HALFSECOND,
ONESECOND,
TWOSECOND, HALFSECOND(HA
None N/A AAU
THREESECOND, LFSECOND)
FOURSECOND,
FIVESECOND
0~31 characters NULL None N/A AAU

SUCCESS,
SUCCESS(SUCCE
FAILURE, None N/A AAU
SS)
UNKNOWTYPE
USERDEFINE, DEFAULT(DEFAUL
None N/A AAU
DEFAULT T)
1.25G, 2.5G, 3.0G,

None None N/A AAU
4.9G, 6.1G, 9.8G
Normal, Fault,
None None N/A AAU
Timeout, NULL

Engineering Design RE
ON, OFF ON(ON) ON Engineering Design RE
1.5~10, step:0.1 30 None Engineering Design RE

1.5~3, step:0.1 20 None Engineering Design RE
Equipment
0~7 None None RE
Planning
Equipment
0~249 None None RE
Planning
Equipment
TRUNK TRUNK(TRUNK) TRUNK RE
Planning
TD_SCDMA,
LTE_TDD,
TDS_TDL,
LTE_FDD,
Equipment
WiMAX_LTE, None None RE
Planning
CDMA_LTE,
GSM_LTE,
UMTS_ONLY,
UMTS_LTE
Equipment
0~8 None None RE
Planning
Equipment
0~8 None None RE
Planning
0~4294967295 None None N/A RE
0~429496729.5,
None None N/A RE
step:0.1
0~429496729.5,
None None N/A RE
step:0.1
0~429496729.5,
None None N/A RE
step:0.1
0~429496729.5,
None None N/A RE
step:0.1
0~50, step:0.1 None None N/A RE
0~6553.5, step:0.1 None None N/A RE
-100~200 None None N/A RE
-100~200 None None N/A RE
0~24 characters None None N/A RE

LO_TD, TL, LO,
WO, WL, C0, CL,
CW, CWL, GO, GL,
GW, GWL, GC,
GCL, GCW, GCWL,
UO, UL, UW, UWL,
None None N/A RE
UC, UCL, UCW,
UCWL, GU, UGL,
UGW, UGWL,
UGC, UGCL,
UGCW, UGCWL,
NULL
CONNECTHEAD,
CONNECTTAIL,
CONNECTBOTH, None None N/A RE
SEPERATEBYBRE
AK, LINKDOWN
0~429496729.5,
None None N/A RE
step:0.1
0~429496729.5,
None None N/A RE
step:0.1

ON, OFF OFF(OFF) ON(ON) N/A RE
1~60 1 1 N/A RE
POW_IQ_MODE,
POW_IQ_MODE(P
POW_MODE, None N/A RE
OW_IQ_MODE)
IQ_MODE
HALFSECOND,
ONESECOND,
None N/A RE
FOURSECOND,
FIVESECOND
0~31 characters NULL None N/A RE

SUCCESS,
SUCCESS(SUCCE
FAILURE, None N/A RE
SS)
UNKNOWTYPE
None N/A RE
DEFAULT T)
1.25G, 2.5G, 3.0G,

None None N/A RE
4.9G, 6.1G, 9.8G
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A RE
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A RE

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A RE
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A RE
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
None None N/A RE
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A RE
483647
-
2147483648~2147 None None N/A RE
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A RE
EDL, Slave
CABINET,
SUBRACK,
None None N/A RE
BOARD,
SUBBOARD, SFP
Normal, Fault,
None None N/A RE
Timeout, NULL
0~62 0 None Engineering Design RFU
4~5 None None Engineering Design RFU
0~8 None None Engineering Design RFU
MRFU, LRFU None None Engineering Design RFU

Engineering Design RFU
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A RFU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A RFU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A RFU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A RFU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A RFU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
0~4294967295 None None N/A RFU
CPU, DSP,
SLAVE_CPU,
None None N/A RFU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A RFU
483647
-
2147483648~2147 None None N/A RFU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A RFU
EDL, Slave
CABINET,
SUBRACK,
None None N/A RFU
BOARD,
SUBBOARD, SFP
ON, OFF ON(ON) ON Engineering Design RFU
1.5~10, step:0.1 30 None Engineering Design RFU

1.5~3, step:0.1 20 None Engineering Design RFU
Equipment
0~7 None None RFU
Planning
Equipment
0~249 None None RFU
Planning
Equipment
TRUNK TRUNK(TRUNK) TRUNK RFU
Planning
TD_SCDMA,
LTE_TDD,
TDS_TDL,
LTE_FDD,
Equipment
WiMAX_LTE, None None RFU
Planning
CDMA_LTE,
GSM_LTE,
UMTS_ONLY,
UMTS_LTE
Equipment
0~8 None None RFU
Planning
Equipment
0~8 None None RFU
Planning
0~429496729.5,
None None N/A RFU
step:0.1
0~429496729.5,
None None N/A RFU
step:0.1
0~429496729.5,
None None N/A RFU
step:0.1
0~429496729.5,
None None N/A RFU
step:0.1
0~50, step:0.1 None None N/A RFU
0~6553.5, step:0.1 None None N/A RFU
-100~200 None None N/A RFU
-100~200 None None N/A RFU

LO_TD, TL, LO,
WO, WL, C0, CL,
CW, CWL, GO, GL,
GW, GWL, GC,
GCL, GCW, GCWL,
UO, UL, UW, UWL,
None None N/A RFU
UC, UCL, UCW,
UCWL, GU, UGL,
UGW, UGWL,
UGC, UGCL,
UGCW, UGCWL,
NULL
CONNECTHEAD,
CONNECTTAIL,
CONNECTBOTH, None None N/A RFU
SEPERATEBYBRE
AK, LINKDOWN
0~429496729.5,
None None N/A RFU
step:0.1
0~429496729.5,
None None N/A RFU
step:0.1

ON, OFF OFF(OFF) ON(ON) N/A RFU
1~60 1 1 N/A RFU
POW_IQ_MODE,
POW_IQ_MODE(P
POW_MODE, None N/A RFU
OW_IQ_MODE)
IQ_MODE
HALFSECOND,
ONESECOND,
None N/A RFU
FOURSECOND,
FIVESECOND
0~31 characters NULL None N/A RFU

SUCCESS,
SUCCESS(SUCCE
FAILURE, None N/A RFU
SS)
UNKNOWTYPE
None N/A RFU
DEFAULT T)
1.25G, 2.5G, 3.0G,

None None N/A RFU
4.9G, 6.1G, 9.8G
Normal, Fault,
None None N/A RFU
Timeout, NULL
0 0 None Engineering Design RRU
60~254 None None Engineering Design RRU
0 0 None Engineering Design RRU
0~31 characters NULL None Engineering Design RRU

MRRU, PRRU,
None None Engineering Design RRU
LRRU
PIMOFFLINE None None N/A RRU
120~300 None None N/A RRU
IsInerefered,
None None N/A RRU
IsNotInterfered

Engineering Design RRU
Alarm_0, Alarm_1,
Alarm_2, Alarm_3,
Alarm_4, Alarm_5,
Alarm_6, Alarm_7,
Alarm_8, Alarm_9,
Alarm_10, None None N/A RRU
Alarm_11,
Alarm_12,
Alarm_13,
Alarm_14,
Alarm_15
Enabled, Disabled None None N/A RRU

Avail_0, Avail_1,
Avail_20, Avail_21,
Avail_500,
Avail_501,
Avail_504,
Avail_508,
Avail_509,
Avail_520,
Avail_521,
Avail_524,
Avail_528,
Avail_529,
Avail_800,
Avail_801,
Avail_820,
Avail_821,
Avail_c10,
Avail_c11,
None None N/A RRU
Avail_c12,
Avail_c13,
Avail_c14,
Avail_c30,
Avail_c31,
Avail_c32,
Avail_c33,
Avail_c34,
Avail_d00,
Avail_d01,
Avail_d04,
Avail_d08,
Avail_d09,
Avail_d20,
Avail_d21,
Avail_d24,
Avail_d28,
Avail_d29
0~2047 characters None None N/A RRU

UMPT, FAN, UPEU,

PMU, PSU, BAT,
TCU, EMU, UTRP,
USCU, UEIU, FMU,
MRRU, MRFU,
RHUB, UBRI,
MRXU, MTXU,
UCIU, CCU, MAAU,
None None N/A RRU
UNKNOWN, PRRU,
GRRU, GRFU,
GATM, DRRU,
DRFU, WRFU,
NGRU, LMPT,
LBBP, LRRU,
LRFU, BRFU,
CRFU, RRU
CPU, DSP,
SLAVE_CPU,
None None N/A RRU
MDU_CPU,
MRU_CPU
-
2147483648~2147 None None N/A RRU
483647
-
2147483648~2147 None None N/A RRU
483647
Master, NDD, NCD,

NDC, NEC, EUL, None None N/A RRU
EDL, Slave
CABINET,
SUBRACK,
None None N/A RRU
BOARD,
SUBBOARD, SFP
ON, OFF ON(ON) ON Engineering Design RRU
1.5~10, step:0.1 30 None Engineering Design RRU

1.5~3, step:0.1 20 None Engineering Design RRU
Equipment
0~7 None None RRU
Planning
Equipment
0~249 None None RRU
Planning
Equipment
TRUNK TRUNK(TRUNK) TRUNK RRU
Planning
TD_SCDMA,
LTE_TDD,
TDS_TDL,
LTE_FDD,
Equipment
WiMAX_LTE, None None RRU
Planning
CDMA_LTE,
GSM_LTE,
UMTS_ONLY,
UMTS_LTE
Equipment
0~8 None None RRU
Planning
Equipment
0~8 None None RRU
Planning
0~429496729.5,
None None N/A RRU
step:0.1
0~429496729.5,
None None N/A RRU
step:0.1
0~429496729.5,
None None N/A RRU
step:0.1
0~429496729.5,
None None N/A RRU
step:0.1
0~50, step:0.1 None None N/A RRU
0~6553.5, step:0.1 None None N/A RRU
-100~200 None None N/A RRU
-100~200 None None N/A RRU

LO_TD, TL, LO,
WO, WL, C0, CL,
CW, CWL, GO, GL,
GW, GWL, GC,
GCL, GCW, GCWL,
UO, UL, UW, UWL,
None None N/A RRU
UC, UCL, UCW,
UCWL, GU, UGL,
UGW, UGWL,
UGC, UGCL,
UGCW, UGCWL,
NULL
CONNECTHEAD,
CONNECTTAIL,
CONNECTBOTH, None None N/A RRU
SEPERATEBYBRE
AK, LINKDOWN
0~429496729.5,
None None N/A RRU
step:0.1
0~429496729.5,
None None N/A RRU
step:0.1

ON, OFF OFF(OFF) ON(ON) N/A RRU
1~60 1 1 N/A RRU
POW_IQ_MODE,
POW_IQ_MODE(P
POW_MODE, None N/A RRU
OW_IQ_MODE)
IQ_MODE
HALFSECOND,
ONESECOND,
None N/A RRU
FOURSECOND,
FIVESECOND
0~31 characters NULL None N/A RRU

SUCCESS,
SUCCESS(SUCCE
FAILURE, None N/A RRU
SS)
UNKNOWTYPE
None N/A RRU
DEFAULT T)
1.25G, 2.5G, 3.0G,

None None N/A RRU
4.9G, 6.1G, 9.8G
Normal, Fault,
None None N/A RRU
Timeout, NULL
0~249 None None Engineering Design RRUCHAIN

CHAIN, RING,
None None Engineering Design RRUCHAIN
LOADBALANCE
COLD, HOT COLD(COLD) None Engineering Design RRUCHAIN
0~7 0 None Engineering Design RRUCHAIN
Equipment
0~8,255 255 None RRUCHAIN
Planning
Equipment
0~8,255 255 None RRUCHAIN
Planning
LOCALPORT, LOCALPORT(local
None Engineering Design RRUCHAIN
PEERPORT port)
1.25G, 2.5G, 4.9G,

AUTO(Auto) None Engineering Design RRUCHAIN
6.1G, 9.8G, AUTO
0~3 None None N/A RRUCHAIN
0~3 None None N/A RRUCHAIN
0~62 0 None Engineering Design RxBranch
4~5,60~254 None None Engineering Design RxBranch

0~8 0 None Engineering Design RxBranch
0~7 None None Engineering Design RxBranch
ON, OFF ON(ON) ON(ON) Engineering Design RxBranch
0~22, step:0.5 0 None Engineering Design RxBranch

ON, OFF None None N/A RxBranch
0~429496729.5,
None None N/A RxBranch
step:0.1
0~429496729.5,
step:0.1
0~31 None None N/A RxBranch

0~429496729.5,
step:0.1
0~429496729.5,
step:0.1
0~31 None None N/A RxBranch

0~62 None None Engineering Design TxBranch
4~5,60~254 None None Engineering Design TxBranch


ON, OFF ON(ON) ON(ON) Engineering Design TxBranch
1~25, step:0.01 None None N/A TxBranch

ON, OFF None None N/A TxBranch
-10~1, step:0.1 0 None N/A TxBranch
20~30 None None N/A TxBranch

0~63 characters None None N/A TxBranch
0,5000~655000,
None None N/A TxBranch
step:10
0,5000~655000,
step:10
0~429496729.5,
step:0.1
0~429496729.5,
step:0.1
0,5000~655000,
step:10
0~429496729.5,
step:0.1
0~429496729.5,
step:0.1
0~429496729.5,
step:0.1
0~429496729.5,
step:0.1
0~6553.5, step:0.1 None None N/A TxBranch
0~6553.5, step:0.1 None None N/A TxBranch
Normal, Unknown,
Crossed
Equipment
Valid IP address 0.0.0.0 None NtpCp
Planning
Equipment
1~525600 None 6 hours NtpCp
Planning
123~5999,6100~65 Equipment
123 None NtpCp
534 Planning
Default/Recommen
IPV4, IPV6 IPV4(IPv4) None NtpCp
ded Value
Equipment
Valid IP address 0:0:0:0:0:0:0:0 None NtpCp
Planning
PLAIN, DES_S,
Equipment
DES_N, DES_A, PLAIN(Plain) None NtpCp
Planning
MD5
Equipment
1~16 characters None None NtpCp
Planning
Equipment
1~4294967295 None None NtpCp
Planning
Slaver, Master Slaver(Slave) None Engineering Design NtpCp

GMT-1200, GMT-
1100, GMT-1000,
GMT-0930, GMT-
0900, GMT-0800,
GMT-0700, GMT-
0600, GMT-0500,
GMT-0430, GMT-
0400, GMT-0330,
GMT-0300, GMT-
0200, GMT-0100,
GMT, GMT+0100,
GMT+0200,
GMT+0300,
GMT+0330,
GMT+0400,
GMT+0430,
GMT+0500,
GMT+0800(GMT+0 Equipment
GMT+0530, None TZ
8:00) Planning
GMT+0545,
GMT+0600,
GMT+0630,
GMT+0700,
GMT+0800,
GMT+0845,
GMT+0900,
GMT+0930,
GMT+1000,
GMT+1030,
GMT+1100,
GMT+1130,
GMT+1200,
GMT+1245,
GMT+1300,
GMT+1400,
CUSTOM
Equipment
NO, YES NO(No) None TZ
Planning
DATE, WEEK, Equipment
DATE(Date mode) None TZ
DATEWEEK Planning
JAN, FEB, MAR,

APR, MAY, JUN, Equipment
JAN(January) None TZ
JUL, AUG, SEP, Planning
OCT, NOV, DEC
Equipment
1~31 1 None TZ
Planning
LAST, FIRST,
Equipment
SECOND, THIRD, FIRST(First) None TZ
Planning
FOURTH
MON, TUE, WED,

Equipment
THU, FRI, SAT, MON(Monday) None TZ
Planning
SUN
Equipment
00:00:00~23:59:59 00:00:00 None TZ
Planning
DATE, WEEK, Equipment

DATE(Date mode) None TZ
DATEWEEK Planning
JAN, FEB, MAR,

APR, MAY, JUN, Equipment
JAN(January) None TZ
JUL, AUG, SEP, Planning
OCT, NOV, DEC
Equipment
1~31 1 None TZ
Planning
LAST, FIRST,
Equipment
SECOND, THIRD, FIRST(First) None TZ
Planning
FOURTH
MON, TUE, WED,

Equipment
THU, FRI, SAT, MON(Monday) None TZ
Planning
SUN
Equipment
00:00:00~23:59:59 00:00:00 None TZ
Planning
Equipment
-120~120 0 None TZ
Planning
-720~840 0 None Engineering Design TZ
2000-01-01~2033-
None None N/A OmuCurTime
12-31
00:00:00~23:59:59 None None N/A OmuCurTime
None None None N/A OmuCurTime
Equipment
NTP, GPS, NONE NTP(NTP) None TimeSrc
Planning
0~30 characters None None N/A TimeSrc

Auto, Plaintext, Default/Recommen
Auto(Auto) None FTPCLT
Encrypted ded Value
Default/Recommen
No, Yes Yes(Yes) None FTPCLT
ded Value
Default/Recommen
No, Yes No(No) None FTPCLT
ded Value
Default/Recommen
Valid IP address 127.0.0.1 None FTPCLTPORT
ded Value
Default/Recommen
21~65535 21 None FTPCLTPORT
ded Value
Radio Planning CnOperatorExtende
0~5 None None
(Internal planning) dQci
CnOperatorExtende
10~254 None None Engineering Design
dQci
CnOperatorExtende
0~9 0 None Engineering Design
dQci
CnOperatorExtende
dQci
Radio Planning CnOperatorStandar

0~5 None None
(Internal planning) dQci
QCI1, QCI2, QCI3,
CnOperatorStandar
QCI4, QCI5, QCI6, None None Engineering Design
dQci
QCI7, QCI8, QCI9
CnOperatorStandar
dQci
CnOperatorStandar
dQci
CSFallBackBlindHo
Cfg
UTRAN, GERAN, Default/Recommen CSFallBackBlindHo
UTRAN UTRAN
CDMA2000 ded Value Cfg
GERAN GERAN
CDMA2000, NULL ded Value Cfg
CDMA2000 CDMA2000
CDMA2000, NULL ded Value Cfg
Default/Recommen CSFallBackBlindHo
OFF, ON OFF(Off) OFF(Off)
ded Value Cfg
ded Value Cfg
ded Value Cfg
Radio Planning
0~5 None None InterPlmnHoList
(Internal planning)
Radio Planning
000~999 None None (Negotiation with InterPlmnHoList
the peer)
Radio Planning
00~99,000~999 None None (Negotiation with InterPlmnHoList
the peer)
RatFreqPriorityGrou
p
LTE, UTRAN, Default/Recommen RatFreqPriorityGrou
None None
GERAN ded Value p
0~45589,64436~65 Radio Planning RatFreqPriorityGrou

None None
535 (Internal planning) p
Radio Planning RatFreqPriorityGrou

0~7 0 None
(Internal planning) p
GSM_dcs1800, RatFreqPriorityGrou
GSM_dcs1800 None Engineering Design
GSM_pcs1900 p
Radio Planning ServiceIfHoCfgGrou
0~5 None None
(Internal planning) p
ServiceIfHoCfgGrou
p
NO_HO, Default/Recommen ServiceIfHoCfgGrou

NO_HO None
PERMIT_HO ded Value p
0~45589,64436~65 Radio Planning ServiceIfHoCfgGrou
0 None
535 (Internal planning) p
Radio Planning ServiceIrHoCfgGro

0~5 None None
(Internal planning) up
ServiceIrHoCfgGro
up
NO_HO,
Default/Recommen ServiceIrHoCfgGro
PERMIT_HO, NO_HO None
ded Value up
MUST_HO
1~256 None None Engineering Design SpidCfg

Default/Recommen
FALSE, TRUE FALSE(FALSE) None SpidCfg
ded Value
NOT_CFG(NOT_C Radio Planning

NOT_CFG, CFG None SpidCfg
FG) (Internal planning)
Radio Planning
0~255 0 None SpidCfg
(Internal planning)
Default/Recommen
FALSE, TRUE TRUE(TRUE) None SpidCfg
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
FALSE, TRUE FALSE(FALSE) None SpidCfg
ded Value
Default/Recommen
0,10~600 0 0 CounterCheckPara
ded Value
Default/Recommen
0,128~4294967295 0 0 CounterCheckPara
ded Value
OFF, ON OFF(Off) OFF(Off) Engineering Design CounterCheckPara
NULL, Snow3G, AES(AES AES(AES

Engineering Design ENodeBCipherCap
AES Algorithm) Algorithm)
NULL, Snow3G, Snow3G(SNOW 3G Snow3G(SNOW 3G

NULL, Snow3G, NULL(NULL NULL(NULL

Default/Recommen ENodeBConnState
10~200 20 20
ded Value Timer
10~200 20 20
ded Value Timer
10~200 35 35
ded Value Timer
NULL, Snow3G, AES(AES AES(AES ENodeBIntegrityCa

Engineering Design
AES Algorithm) Algorithm) p
NULL, Snow3G, Snow3G(SNOW 3G Snow3G(SNOW 3G ENodeBIntegrityCa

Engineering Design
NULL, Snow3G, NULL(NULL NULL(NULL ENodeBIntegrityCa
Engineering Design
OFF, ON ON(On) ON(On) Engineering Design GlobalProcSwitch
X2_OVER_M2000(
X2_OVER_M2000,
X2SonLink is set up None Engineering Design GlobalProcSwitch
X2_OVER_S1
over M2000)

LCG_PROFILE_0,
LCG_PROFILE_0 LCG_PROFILE_0 Engineering Design GlobalProcSwitch
LCG_PROFILE_1
OFF, ON OFF(Off) OFF(Off) Engineering Design GlobalProcSwitch

OFF, ON OFF(Off) OFF(Off) Engineering Design GlobalProcSwitch

OFF, ON OFF(Off) OFF(Off) Engineering Design PdcpRohcPara
U_MODE,
U_MODE(Unidirecti U_MODE(Unidirecti
O_MODE, Engineering Design PdcpRohcPara
onal Mode) onal Mode)
R_MODE
Profile0x0001, Profile0x0001:on, Profile0x0001: on;
Engineering Design PdcpRohcPara
Profile0x0004 Profile0x0004:on Profile0x0004: on
Default/Recommen
1~16 4 4 RrcConnStateTimer
ded Value
min5, min10,
min20, min30, Default/Recommen
min10(10) min10(10) RrcConnStateTimer
min60, min120, ded Value
min180
ms50, ms100,
ms150, ms200, Default/Recommen
ms500(500) ms500(500) RrcConnStateTimer
ms500, ms1000, ded Value
ms2000
ms100, ms200,
ms500, ms1000, Default/Recommen
ms8000(8000) ms8000(8000) RrcConnStateTimer
ms2000, ms4000, ded Value
ms8000
min5, min10,
min20, min30, Default/Recommen
min120(120) min120(120) RrcConnStateTimer
min60, min120, ded Value
min180
Default/Recommen
ded Value
Default/Recommen
ded Value
0~255 None None N/A TceIpMapping
IPv4, IPv6 IPv4(IPv4 Address) None N/A TceIpMapping
Valid IP address 0.0.0.0 None N/A TceIpMapping

Valid IP address 0:0:0:0:0:0:0:0 None N/A TceIpMapping
Radio Planning eNBCellQciRsvdPa

0~17 None None
(Internal planning) ra
Radio Planning eNBCellQciRsvdPa

1~254 None None
(Internal planning) ra
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
ameter0_bit16:Off, eNBCellQciRsvdPa
RsvdSwPara0_bit1 None Engineering Design
ReservedSwitchPar ra
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
ameter1_bit16:Off, eNBCellQciRsvdPa
ReservedSwitchPar ra
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
eNBCellQciRsvdPa
RsvdSwPara2_bit1 None None Engineering Design
ra
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
eNBCellQciRsvdPa
ra
Radio Planning eNBCnOpQciRsvd

0~5 None None
(Internal planning) Para
Radio Planning eNBCnOpQciRsvd

1~254 None None
(Internal planning) Para
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
ameter0_bit16:Off, eNBCnOpQciRsvd
ReservedSwitchPar Para
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
ameter1_bit16:Off, eNBCnOpQciRsvd
ReservedSwitchPar Para
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
eNBCnOpQciRsvd
RsvdSwPara2_bit1 None None Engineering Design
Para
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
eNBCnOpQciRsvd
Para
Radio Planning
0~5 None None eNBCnOpRsvdPara
(Internal planning)
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
ameter0_bit16:Off,
RsvdSwPara0_bit1 None Engineering Design eNBCnOpRsvdPara
ReservedSwitchPar
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
ameter1_bit16:Off,
RsvdSwPara1_bit1 None Engineering Design eNBCnOpRsvdPara
ReservedSwitchPar
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
RsvdSwPara2_bit1 None None Engineering Design eNBCnOpRsvdPara
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
0~4294967295 0 None Engineering Design eNBCnOpRsvdPara










Radio Planning
1~254 None None eNBQciRsvdPara
(Internal planning)
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
ameter0_bit16:Off,
RsvdSwPara0_bit1 None Engineering Design eNBQciRsvdPara
ReservedSwitchPar
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
ameter1_bit16:Off,
RsvdSwPara1_bit1 None Engineering Design eNBQciRsvdPara
ReservedSwitchPar
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
RsvdSwPara2_bit1 None None Engineering Design eNBQciRsvdPara
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
0~4294967295 0 None Engineering Design eNBQciRsvdPara










Radio Planning
0~17 None None CellDlpcPdschPa
(Internal planning)
Default/Recommen
OFF, ON OFF(Off) OFF(Off) CellDlpcPdschPa
ded Value
DB_6_P_A,
DB_4DOT77_P_A,
Dual-antenna or
DB_3_P_A,
four-antenna:
DB_1DOT77_P_A, Default/Recommen
DB_3_P_A(-3 dB) DB_3_P_A(-3 dB) CellDlpcPdschPa
DB0_P_A, ded Value
Single-antenna:
DB1_P_A,
DB0_P_A(0 dB)
DB2_P_A,
DB3_P_A
Radio Planning
0~17 None None CellDrxPara
(Internal planning)
Default/Recommen
0~999 300 300 CellDrxPara
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
40~6000, step:20 30 30 CellDrxPara
ded Value
Radio Planning
0~17 None None CellUlpcDedic
(Internal planning)
UU_DISABLE, UU_DISABLE(Disa UU_DISABLE(Disa Default/Recommen

CellUlpcDedic
UU_ENABLE ble) ble) ded Value
Default/Recommen
-10.5~12, step:1.5 -30 -30 CellUlpcDedic
ded Value
Default/Recommen
-3~12 -30 -30 CellUlpcDedic
ded Value
UU_FC0_FILTER_
COEFF,
UU_FC1_FILTER_
COEFF,
UU_FC2_FILTER_
COEFF,
UU_FC3_FILTER_
COEFF,
UU_FC4_FILTER_
COEFF,
UU_FC5_FILTER_
COEFF,
UU_FC6_FILTER_
COEFF,
UU_FC6_FILTER_ UU_FC6_FILTER_
UU_FC7_FILTER_ Default/Recommen
COEFF(UU_FC6_F COEFF(UU_FC6_F CellUlpcDedic
COEFF, ded Value
ILTER_COEFF) ILTER_COEFF)
UU_FC8_FILTER_
COEFF,
UU_FC9_FILTER_
COEFF,
UU_FC11_FILTER_
COEFF,
UU_FC13_FILTER_
COEFF,
UU_FC15_FILTER_
COEFF,
UU_FC17_FILTER_
COEFF,
UU_FC19_FILTER_
COEFF
0~17 None None Engineering Design DistBasedHO
EUTRAN:On, EUTRAN:On,
EUTRAN, GERAN,
GERAN:Off, GERAN:Off, Engineering Design DistBasedHO
UTRAN
UTRAN:Off UTRAN:Off
100~100000 10 10 Engineering Design DistBasedHO
Radio Planning
0~17 None None DrxParaGroup
(Internal planning)
0~9 None None Engineering Design DrxParaGroup

QCI 1: ON(On)
QCI 2: OFF(Off)
QCI 3: OFF(Off)
QCI 4: ON(On)
OFF, ON OFF(Off) QCI 5: OFF(Off) Engineering Design DrxParaGroup
QCI 6: ON(On)
QCI 7: OFF(Off)
QCI 8: ON(On)
QCI 9: ON(On)
Configuration 4:
PSF4(4 subframes)
QCI 4-TDD-
Configuration 5:
PSF4(4 subframes)
QCI 4-TDD-
Configuration 6:
PSF2(2 subframes)
QCI 6-FDD: PSF2(2
subframes)
QCI 6-TDD-
Configuration 0:
PSF2(2 subframes)
QCI 6-TDD-
Configuration 1:
PSF2(2 subframes)
PSF1, PSF2, PSF3,
QCI 6-TDD-
PSF4, PSF5, PSF6,
Configuration 2:
PSF8, PSF10,
PSF4(4 subframes)
PSF20, PSF30, PSF2(2 subframes) Engineering Design DrxParaGroup
QCI 6-TDD-
PSF40, PSF50,
Configuration 3:
PSF60, PSF80,
PSF4(4 subframes)
PSF100, PSF200
QCI 6-TDD-
Configuration 4:
PSF4(4 subframes)
QCI 6-TDD-
Configuration 5:
PSF4(4 subframes)
QCI 6-TDD-
Configuration 6:
PSF2(2 subframes)
QCI 8-FDD: PSF2(2
subframes)
QCI 8-TDD-
Configuration 0:
PSF2(2 subframes)
QCI 8-TDD-
Configuration 1:
QCI 4-TDD-
Configuration 5:
PSF10(10
subframes)
QCI 4-TDD-
Configuration 6:
PSF4(4 subframes)
QCI 6-FDD: PSF3(3
subframes)
QCI 6-TDD-
Configuration 0:
PSF3(3 subframes)
QCI 6-TDD-
Configuration 1:
PSF1, PSF2, PSF3, PSF3(3 subframes)
PSF4, PSF5, PSF6, QCI 6-TDD-
PSF8, PSF10, Configuration 2:
PSF20, PSF30, PSF5(5 subframes)
PSF40, PSF50, QCI 6-TDD-
PSF3(3 subframes) Engineering Design DrxParaGroup
PSF300, PSF500, QCI 6-TDD-
PSF1920, PSF2560 PSF8(8 subframes)
QCI 6-TDD-
Configuration 5:
PSF10(10
subframes)
QCI 6-TDD-
Configuration 6:
PSF3(3 subframes)
QCI 8-FDD: PSF3(3
subframes)
QCI 8-TDD-
Configuration 0:
PSF3(3 subframes)
QCI 8-TDD-
Configuration 1:
QCI 1: sf8(8
subframes)
QCI 4: sf8(8
subframes)
sf1, sf2, sf4, sf6, QCI 6: sf8(8
sf8(8 subframes) Engineering Design DrxParaGroup
sf8, sf16, sf24, sf33 subframes)
QCI 8: sf8(8
subframes)
QCI 9: sf8(8
subframes)
QCI 1: SF20(20
subframes)
SF10, SF20, SF32,
QCI 4: SF20(20
SF40, SF64, SF80,
subframes)
SF128, SF160,
SF40(40 QCI 6: SF40(40
SF256, SF320, Engineering Design DrxParaGroup
subframes) subframes)
SF512, SF640,
QCI 8: SF40(40
SF1024, SF1280,
subframes)
SF2048, SF2560
QCI 9: SF40(40
subframes)
QCI 1:
UU_DISABLE(Disa
ble)
QCI 4:
UU_ENABLE(Enabl
e)
QCI 6:
UU_DISABLE, UU_ENABLE(Enabl
UU_ENABLE(Enabl Engineering Design DrxParaGroup
UU_ENABLE e)
e)
QCI 8:
UU_ENABLE(Enabl
e)
QCI 9:
UU_ENABLE(Enabl
e)
QCI 4: SF5(5
SF2, SF5, SF8,
subframes)
SF10, SF16, SF20,
QCI 6: SF5(5
SF32, SF40, SF64,
subframes)
SF80, SF128, SF5(5 subframes) Engineering Design DrxParaGroup
QCI 8: SF5(5
SF160, SF256,
subframes)
SF320, SF512,
QCI 9: SF5(5
SF640
subframes)
QCI 4: 2
QCI 6: 8
1~16 8 Engineering Design DrxParaGroup
QCI 8: 8
QCI 9: 8
InterRatHoCommGr
oup
InterRatHoCommGr
oup
Default/Recommen InterRatHoCommGr
0~15, step:0.5 2 None
ded Value oup
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Default/Recommen InterRatHoCommGr
640ms None
480ms, 512ms, ded Value oup
640ms, 1024ms,
1280ms, 2560ms,
5120ms
-141~-43 -111 None
ded Value oup
-20~-3, step:0.5 -20 None
ded Value oup
-141~-43 -115 None
ded Value oup
-20~-3, step:0.5 -24 None
ded Value oup
0~15 6 None
ded Value oup
InterRatHoCdma1x
RttGroup
InterRatHoCdma1x
RttGroup
Default/Recommen InterRatHoCdma1x
0~15, step:0.5 2 2
ded Value RttGroup
-31.5~0, step:0.5 -28 -28
ded Value RttGroup
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Default/Recommen InterRatHoCdma1x
640ms 640ms
480ms, 512ms, ded Value RttGroup
640ms, 1024ms,
1280ms, 2560ms,
5120ms
-31.5~0, step:0.5 -24 -24
ded Value RttGroup
RlfTimerConstGrou
p
RlfTimerConstGrou
p
MS100_T301,
MS200_T301,
MS300_T301,
MS400_T301, MS200_T301(200m MS200_T301(200m Default/Recommen RlfTimerConstGrou
MS600_T301, s) s) ded Value p
MS1000_T301,
MS1500_T301,
MS2000_T301
QCI1:MS200_T310
(200ms)
QCI2:MS1000_T31
0(1000ms)
QCI3:MS1000_T31
0(1000ms)
MS0_T310,
QCI4:MS1000_T31
MS50_T310,
0(1000ms)
MS100_T310,
MS1000_T310(100 QCI5:MS1000_T31 Default/Recommen RlfTimerConstGrou
MS200_T310,
0ms) 0(1000ms) ded Value p
MS500_T310,
QCI6:MS1000_T31
MS1000_T310,
0(1000ms)
MS2000_T310
QCI7:MS1000_T31
0(1000ms)
QCI8:MS1000_T31
0(1000ms)
QCI9:MS1000_T31
0(1000ms)
MS1000_T311,
MS3000_T311,
MS5000_T311,
MS10000_T311(10 MS10000_T311(10 Default/Recommen RlfTimerConstGrou
MS10000_T311,
000ms) 000ms) ded Value p
MS15000_T311,
MS20000_T311,
MS30000_T311
QCI1:n6(6)
QCI2:n10(10)
QCI3:n10(10)
QCI4:n10(10)
n1, n2, n3, n4, n6, Default/Recommen RlfTimerConstGrou
n10(10) QCI5:n10(10)
n8, n10, n20 ded Value p
QCI6:n10(10)
QCI7:n10(10)
QCI8:n10(10)
QCI9:n10(10)
QCI1:n5(5)
QCI2:n1(1)
QCI3:n1(1)
QCI4:n1(1)
n1, n2, n3, n4, n5, Default/Recommen RlfTimerConstGrou
n1(1) QCI5:n1(1)
n6, n8, n10 ded Value p
QCI6:n1(1)
QCI7:n1(1)
QCI8:n1(1)
QCI9:n1(1)
10~254 None None Engineering Design CellExtendedQci
0~17 None None Engineering Design CellExtendedQci
Default/Recommen
0~9 0 None CellExtendedQci
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
0~9 0 None Engineering Design CellExtendedQci

NOT_CFG(NOT_C
NOT_CFG, CFG None Engineering Design CellExtendedQci
FG)
Radio Planning
0~17 None None CellStandardQci
(Internal planning)
QCI1, QCI2, QCI3,

QCI4, QCI5, QCI6, None None Engineering Design CellStandardQci
QCI7, QCI8, QCI9
0~9 0 None Engineering Design CellStandardQci


ms5, ms10, ms20,
ms10(SRI 10ms) None Engineering Design CellStandardQci
ms40, ms80
NOT_CFG(NOT_C
NOT_CFG, CFG None Engineering Design CellStandardQci
FG)
InterRatHoCdmaHr
pdGroup
InterRatHoCdmaHr
pdGroup
Default/Recommen InterRatHoCdmaHr
0~15, step:0.5 2 2
ded Value pdGroup
-31.5~0, step:0.5 -14 -14
ded Value pdGroup
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Default/Recommen InterRatHoCdmaHr
640ms 640ms
480ms, 512ms, ded Value pdGroup
640ms, 1024ms,
1280ms, 2560ms,
5120ms
-31.5~0, step:0.5 -10 -10
ded Value pdGroup
InterRatHoGeranGr
oup
InterRatHoGeranGr
oup
Default/Recommen InterRatHoGeranGr
0~15, step:0.5 2 None
ded Value oup
-110~-48 -100 None
ded Value oup
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Default/Recommen InterRatHoGeranGr
640ms 640ms
480ms, 512ms, ded Value oup
640ms, 1024ms,
1280ms, 2560ms,
5120ms
-110~-48 -98 None
ded Value oup
InterRatHoUtranGro
up
InterRatHoUtranGro
up
Default/Recommen InterRatHoUtranGro
-24~0, step:0.5 -20 None
ded Value up
-120~-25 -103 None
ded Value up
0~15, step:0.5 2 None
ded Value up
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Default/Recommen InterRatHoUtranGro
640ms None
480ms, 512ms, ded Value up
640ms, 1024ms,
1280ms, 2560ms,
5120ms
-24~0, step:0.5 -18 None
ded Value up
-120~-25 -101 None
ded Value up
0~17 None None Engineering Design InterFreqHoGroup
0~9 None None Engineering Design InterFreqHoGroup
Default/Recommen
0~15, step:0.5 2 2 InterFreqHoGroup
ded Value
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Default/Recommen
640ms None InterFreqHoGroup
480ms, 512ms, ded Value
640ms, 1024ms,
1280ms, 2560ms,
5120ms
Default/Recommen
-141~-43 -105 None InterFreqHoGroup
ded Value
Default/Recommen
-20~-3, step:0.5 -20 None InterFreqHoGroup
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
0~15, step:0.5 2 2 InterFreqHoGroup
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
640ms None InterFreqHoGroup
640ms, 1024ms,
1280ms, 2560ms,
5120ms
Default/Recommen
-141~-43 -103 -103 InterFreqHoGroup
ded Value
Default/Recommen
-20~-3, step:0.5 -18 -18 InterFreqHoGroup
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
-15~15, step:0.5 2 2 InterFreqHoGroup
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
0~17 None None Engineering Design IntraFreqHoGroup

0~9 None None Engineering Design IntraFreqHoGroup
Default/Recommen
0~15, step:0.5 2 2 IntraFreqHoGroup
ded Value
Default/Recommen
-15~15, step:0.5 2 2 IntraFreqHoGroup
ded Value
0ms, 40ms, 64ms,

80ms, 100ms,
128ms, 160ms,
320ms 320ms IntraFreqHoGroup
640ms, 1024ms,
1280ms, 2560ms,
5120ms
Radio Planning
0~5 None None CnOperator
(Internal planning)
1~32 characters None None N/A CnOperator
CNOPERATOR_PR
IMARY, Radio Planning
None None CnOperator
CNOPERATOR_SE (Internal planning)
CONDARY
Radio Planning
000~999 None None CnOperator
(Internal planning)
Radio Planning
00~99,000~999 None None CnOperator
(Internal planning)
Radio Planning
0~65535 None None CnOperatorIpPath
(Internal planning)
Radio Planning
0~5 None None CnOperatorIpPath
(Internal planning)
Radio Planning
0~65535 None None CnOperatorTa
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
0~5 None None Emc
(Internal planning)
OFF, ON OFF(Off) None Engineering Design Emc
OFF, ON OFF(Off) None Engineering Design Emc
1~15 1 1 Engineering Design Emc

1~15 1 1 Engineering Design Emc
INDEPENDENT,
INDEPENDENT(Ind
SHARED_FREQ, Radio Planning ENodeBSharingMo
ependent Operator None
SEPARATED_FRE (Internal planning) de
Mode)
Q
Radio Planning LicenseSharingPoli

0~5 None None
(Internal planning) cy
LicenseSharingPoli
cy
1~300 1 None Engineering Design S1ReestTimer
1~300 300 None Engineering Design S1ReestTimer

Radio Planning
0~15 None None S1Interface
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
Release_R8, Radio Planning

Release_R8(Releas
Release_R9, None (Negotiation with S1Interface
e 8)
Release_R10 the peer)
FALSE, TRUE FALSE(FALSE) None N/A S1Interface
Normal, Abnormal None None N/A S1Interface
Normal, Abnormal,
None None N/A S1Interface
Blocked
FALSE, TRUE,
NULL
0~3600 None None N/A S1Interface
0~150 characters None None N/A S1Interface

0~255 None None N/A S1Interface
Null,
LowerLinkFault,
MmecImpact,
SetupFail, CfgErr,
LicRestrict,
PlmnDiff,
TacNotCfg,
Undefine
Radio Planning
0~15 None None MmeFeatureCfg
(Internal planning)
DISABLE, ENABLE DISABLE(disable) None Engineering Design MmeFeatureCfg
000~999 None None Engineering Design X2BlackWhiteList
00~99,000~999 None None Engineering Design X2BlackWhiteList
0~1048575 None None Engineering Design X2BlackWhiteList

X2_BLACK_LIST_T
X2_BLACK_LIST_T
YPE, Radio Planning
YPE(X2 Black List None X2BlackWhiteList
X2_WHITE_LIST_T (Internal planning)
Type)
YPE
Radio Planning
16~79 None None X2Interface
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
Release_R8,
Release_R10(Rele Radio Planning
Release_R9, None X2Interface
ase 10) (Internal planning)
Release_R10
FORBID_AUTO_R
FORBID_AUTO_R FORBID_AUTO_R
MV, Radio Planning
MV(Forbid Auto MV(Forbid Auto X2Interface
PERMIT_AUTO_R (Internal planning)
Remove) Remove)
MV
0~50 characters None None N/A X2Interface
0~50 characters None None N/A X2Interface
Normal, Abnormal None None N/A X2Interface

SCTP_LINK_FAULT
,
SETUP_FAILURE_
OCCUR,
PEERIN_BLACK_L None None N/A X2Interface
IST,
STATE_NORMAL,
SETUP_ONLY_ON
E_LINK_ALLOWED
OFF, ON OFF(Off) OFF(Off) Engineering Design Drx
Default/Recommen
OFF, ON ON(On) ON(On) Drx
ded Value
SF10, SF20, SF32,
SF40, SF64, SF80,
SF128, SF160,
SF10(10 SF10(10 Default/Recommen
SF256, SF320, Drx
subframes) subframes) ded Value
SF512, SF640,
SF1024, SF1280,
SF2048, SF2560
PSF4(4 subframes)
PSF2(2 subframes)
for TDD in
subframe
configuration 0
PSF2(2 subframes)
for TDD in
subframe
configuration 1
PSF3(3 subframes)
for TDD in
PSF1, PSF2, PSF3, subframe
PSF4, PSF5, PSF6, configuration 2
Default/Recommen
PSF20, PSF30, PSF4(4 subframes) for TDD in Drx
ded Value
PSF40, PSF50, subframe
PSF60, PSF80, configuration 3
PSF100, PSF200 PSF3(3 subframes)
for TDD in
subframe
configuration 4
PSF2(3 subframes)
for TDD in
subframe
configuration 5
PSF2(2 subframes)
for TDD in
subframe
configuration 6
PSF5(5 subframes)
for FDD
PSF3(3 subframes)
for TDD in
subframe
configuration 0
PSF3(3 subframes)
for TDD in
subframe
configuration 1
PSF1, PSF2, PSF3, PSF4(4 subframes)
PSF4, PSF5, PSF6, for TDD in
PSF40, PSF50, PSF3(3 subframes) Default/Recommen
PSF5(5 subframes) Drx
PSF60, PSF80, for TDD in ded Value
PSF1920, PSF2560 for TDD in
subframe
configuration 4
PSF4(4 subframes)
for TDD in
subframe
configuration 5
PSF3(3 subframes)
for TDD in
subframe
configuration 6
UU_DISABLE, UU_DISABLE(Disa UU_DISABLE(Disa Default/Recommen

Drx
UU_ENABLE ble) ble) ded Value
SF2, SF5, SF8,
SF10, SF16, SF20,
SF32, SF40, SF64,
SF80, SF128, Drx
SF160, SF256,
SF320, SF512,
SF640
Default/Recommen
1~16 1 1 Drx
ded Value
SF128, SF160,
SF256, SF320,
SF512, SF640, Drx
SF1024, SF1280,
SF2048, SF2560
SF128, SF160,
SF256, SF320,
SF512, SF640, Drx
SF1024, SF1280,
SF2048, SF2560
10~254 None None Engineering Design ExtendedQci

IMS signaling:
IMSSignalling(IMS
Signalling)
Low-delay service:
IMSSignalling, LowDelay(Low
TCPorBuffStreamin
LowDelay, Delay)
g(TCP Based or Engineering Design ExtendedQci
TCPorBuffStreamin TCP service or non-
Buffered Streaming)
g real-time streaming
service:
TCPorBuffStreamin
g(TCP Based or
Buffered Streaming)
IMS signaling: 1000

Low-delay service:
900
0.001~1, step:0.001 700 Engineering Design ExtendedQci
TCP service or non-
real-time streaming
service: 700
IMS signaling: 1000

Low-delay service:
900
0.001~1, step:0.001 700 Engineering Design ExtendedQci
TCP service or non-
real-time streaming
service: 700
MinGbrRate_0_KB,
MinGbrRate_1_KB,
MinGbrRate_2_KB,
MinGbrRate_4KB,
MinGbrRate_8_KB,
MinGbrRate_16_K
B,
MinGbrRate_32_K
MinGbrRate_1_KB( MinGbrRate_1_KB(
B, Engineering Design ExtendedQci
1KB/s) 1KB/s)
MinGbrRate_64_K
B,
MinGbrRate_128_K
B,
MinGbrRate_256_K
B,
MinGbrRate_512_K
B
MinGbrRate_0_KB,
MinGbrRate_1_KB,
MinGbrRate_2_KB,
MinGbrRate_4KB,
MinGbrRate_8_KB,
MinGbrRate_16_K
B,
MinGbrRate_32_K
B, Engineering Design ExtendedQci
1KB/s) 1KB/s)
MinGbrRate_64_K
B,
MinGbrRate_128_K
B,
MinGbrRate_256_K
B,
MinGbrRate_512_K
B
0~1, step:0.1 10 10 Engineering Design ExtendedQci
0~39 0 None Engineering Design ExtendedQci
PBR_0_KBps,
PBR_8_KBps,
PBR_16_KBps,
PBR_32_KBps, PBR_8_KBps(8KB/ PBR_8_KBps(8KB/
Engineering Design ExtendedQci
PBR_64_KBps, s) s)
PBR_128_KBps,
PBR_256_KBps,
PBR_INFINITY
9~16 11 11 Engineering Design ExtendedQci
0~39 5 None Engineering Design ExtendedQci
PAID_USER, PAID_USER(Paid PAID_USER(Paid

Engineering Design ExtendedQci
FREE_USER User) User)
FLOW_CTRL, FLOW_CTRL(Flow
None Engineering Design ExtendedQci
NON_FLOW_CTRL Control)
InterRatPolicyCfgGr
oup
PS_HO:On,
PS_HO, SRVCC, Default/Recommen InterRatPolicyCfgGr
SRVCC:Off, None
REDIRECTION ded Value oup
REDIRECTION:Off
Default/Recommen InterRatPolicyCfgGr
SRVCC SRVCC:On None
ded Value oup
PS_HO:On,
PS_HO,
NACC_HO:Off,
NACC_HO, Default/Recommen InterRatPolicyCfgGr
CCO_HO:Off, None
CCO_HO, SRVCC, ded Value oup
SRVCC:Off,
REDIRECTION
REDIRECTION:Off
CDMA1XRTTHoSw Default/Recommen InterRatPolicyCfgGr

SRVCC None
itch:On ded Value oup
OPT_HO, OPT_HO:On, Default/Recommen InterRatPolicyCfgGr
None
NON_OPT_HO NON_OPT_HO:Off ded Value oup
PERMIT_HO_ENU
M, PERMIT_HO_ENU Default/Recommen InterRatPolicyCfgGr
None
FORBID_HO_ENU M(Permit Ho) ded Value oup
M
PERMIT_FAST_AN
R_MEAS_ENUM, PERMIT_FAST_AN Default/Recommen InterRatPolicyCfgGr
None
FORBID_FAST_AN R_MEAS_ENUM ded Value oup
R_MEAS_ENUM
Default/Recommen
0~15 12 None PuschParam
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
0~39 None None Engineering Design RlcPdcpParaGroup

DiscardTimer_50,
DiscardTimer_100,
DiscardTimer_150,
DiscardTimer_300,
DiscardTimer_500, DiscardTimer_1500 Default/Recommen
None RlcPdcpParaGroup
DiscardTimer_750, (1500 ms) ded Value
DiscardTimer_1500
,
DiscardTimer_Infinit
y
RlcMode_AM, RlcMode_AM(Ackn Default/Recommen

RlcMode_UM owledge Mode) ded Value
Maxretx_Threshold
_t1,
Maxretx_Threshold
_t2,
Maxretx_Threshold
_t3,
Maxretx_Threshold
_t4, Maxretx_Threshold Default/Recommen
Maxretx_Threshold _t8(8) ded Value
_t6,
Maxretx_Threshold
_t8,
Maxretx_Threshold
_t16,
Maxretx_Threshold
_t32
Maxretx_Threshold
_t1,
Maxretx_Threshold
_t2,
Maxretx_Threshold
_t3,
Maxretx_Threshold
_t4, Maxretx_Threshold Default/Recommen
Maxretx_Threshold _t8(8) ded Value
_t6,
Maxretx_Threshold
_t8,
Maxretx_Threshold
_t16,
Maxretx_Threshold
_t32
PollByte_kb25,
PollByte_kb50,
PollByte_kb75,
PollByte_kb100,
PollByte_kb125,
PollByte_kb250,
PollByte_kb375,
PollByte_kb25(25 Default/Recommen
PollByte_kb500, None RlcPdcpParaGroup
kBytes) ded Value
PollByte_kb750,
PollByte_kb1000,
PollByte_kb1250,
PollByte_kb1500,
PollByte_kb2000,
PollByte_kb3000,
PollByte_infinity
PollByte_kb25,
PollByte_kb50,
PollByte_kb75,
PollByte_kb100,
PollByte_kb125,
PollByte_kb250,
PollByte_kb375,
PollByte_kb25(25 Default/Recommen
PollByte_kb500, None RlcPdcpParaGroup
kBytes) ded Value
PollByte_kb750,
PollByte_kb1000,
PollByte_kb1250,
PollByte_kb1500,
PollByte_kb2000,
PollByte_kb3000,
PollByte_infinity
PollPdu_p4,
PollPdu_p8,
PollPdu_p16,
PollPdu_p32, PollPdu_p32(32 Default/Recommen
PollPdu_p64, PDUs) ded Value
PollPdu_p128,
PollPdu_p256,
PollPdu_Infinity
PollPdu_p4,
PollPdu_p8,
PollPdu_p16,
PollPdu_p32, PollPdu_p32(32 Default/Recommen
PollPdu_p64, PDUs) ded Value
PollPdu_p128,
PollPdu_p256,
PollPdu_Infinity
Tpollretrans_m50,
Tpollretrans_m55,
Tpollretrans_m60,
Tpollretrans_m65,
Tpollretrans_m70,
Tpollretrans_m75,
Tpollretrans_m80,
Tpollretrans_m85,
Tpollretrans_m90,
Tpollretrans_m95,
Tpollretrans_m100,
Tpollretrans_m105,
Tpollretrans_m110,
Tpollretrans_m115,
Tpollretrans_m120,
Tpollretrans_m125,
Tpollretrans_m130,
Tpollretrans_m135,
Tpollretrans_m40(4 Default/Recommen
Tpollretrans_m140, None RlcPdcpParaGroup
0ms) ded Value
Tpollretrans_m145,
Tpollretrans_m150,
Tpollretrans_m155,
Tpollretrans_m160,
Tpollretrans_m165,
Tpollretrans_m170,
Tpollretrans_m175,
Tpollretrans_m180,
Tpollretrans_m185,
Tpollretrans_m190,
Tpollretrans_m195,
Tpollretrans_m200,
Tpollretrans_m205,
Tpollretrans_m210,
Tpollretrans_m215,
Tpollretrans_m220,
Tpollretrans_m225,
Tpollretrans_m230,
Tpollretrans_m50,
Tpollretrans_m55,
Tpollretrans_m60,
Tpollretrans_m65,
Tpollretrans_m70,
Tpollretrans_m75,
Tpollretrans_m80,
Tpollretrans_m85,
Tpollretrans_m90,
Tpollretrans_m95,
Tpollretrans_m100,
Tpollretrans_m105,
Tpollretrans_m110,
Tpollretrans_m115,
Tpollretrans_m120,
Tpollretrans_m125,
Tpollretrans_m130,
Tpollretrans_m135,
Tpollretrans_m50(5 Default/Recommen
Tpollretrans_m140, None RlcPdcpParaGroup
0ms) ded Value
Tpollretrans_m145,
Tpollretrans_m150,
Tpollretrans_m155,
Tpollretrans_m160,
Tpollretrans_m165,
Tpollretrans_m170,
Tpollretrans_m175,
Tpollretrans_m180,
Tpollretrans_m185,
Tpollretrans_m190,
Tpollretrans_m195,
Tpollretrans_m200,
Tpollretrans_m205,
Tpollretrans_m210,
Tpollretrans_m215,
Tpollretrans_m220,
Tpollretrans_m225,
Tpollretrans_m230,
Tstatprohibit_m45,
Tstatprohibit_m50,
Tstatprohibit_m55,
Tstatprohibit_m60,
Tstatprohibit_m65,
Tstatprohibit_m70,
Tstatprohibit_m75,
Tstatprohibit_m80,
Tstatprohibit_m85,
Tstatprohibit_m90,
Tstatprohibit_m95,
Tstatprohibit_m100,
Tstatprohibit_m105,
Tstatprohibit_m110,
Tstatprohibit_m115,
Tstatprohibit_m120,
Tstatprohibit_m125,
Tstatprohibit_m130,
Tstatprohibit_m135, Tstatprohibit_m50(5 Default/Recommen
Tstatprohibit_m140, 0ms) ded Value
Tstatprohibit_m145,
Tstatprohibit_m150,
Tstatprohibit_m155,
Tstatprohibit_m160,
Tstatprohibit_m165,
Tstatprohibit_m170,
Tstatprohibit_m175,
Tstatprohibit_m180,
Tstatprohibit_m185,
Tstatprohibit_m190,
Tstatprohibit_m195,
Tstatprohibit_m200,
Tstatprohibit_m205,
Tstatprohibit_m210,
Tstatprohibit_m215,
Tstatprohibit_m220,
Tstatprohibit_m225,
Tstatprohibit_m230,
Tstatprohibit_m45,
Tstatprohibit_m50,
Tstatprohibit_m55,
Tstatprohibit_m60,
Tstatprohibit_m65,
Tstatprohibit_m70,
Tstatprohibit_m75,
Tstatprohibit_m80,
Tstatprohibit_m85,
Tstatprohibit_m90,
Tstatprohibit_m95,
Tstatprohibit_m100,
Tstatprohibit_m105,
Tstatprohibit_m110,
Tstatprohibit_m115,
Tstatprohibit_m120,
Tstatprohibit_m125,
Tstatprohibit_m130,
Tstatprohibit_m135, Tstatprohibit_m40(4 Default/Recommen
Tstatprohibit_m140, 0ms) ded Value
Tstatprohibit_m145,
Tstatprohibit_m150,
Tstatprohibit_m155,
Tstatprohibit_m160,
Tstatprohibit_m165,
Tstatprohibit_m170,
Tstatprohibit_m175,
Tstatprohibit_m180,
Tstatprohibit_m185,
Tstatprohibit_m190,
Tstatprohibit_m195,
Tstatprohibit_m200,
Tstatprohibit_m205,
Tstatprohibit_m210,
Tstatprohibit_m215,
Tstatprohibit_m220,
Tstatprohibit_m225,
Tstatprohibit_m230,
Treordering_m0,
Treordering_m5,
Treordering_m10,
Treordering_m15,
Treordering_m20,
Treordering_m25,
Treordering_m30,
Treordering_m35,
Treordering_m40,
Treordering_m45,
Treordering_m50,
Treordering_m55,
Treordering_m60,
Treordering_m65,
Treordering_m70,
Treordering_m50(5 Default/Recommen
Treordering_m75, None RlcPdcpParaGroup
0ms) ded Value
Treordering_m80,
Treordering_m85,
Treordering_m90,
Treordering_m95,
Treordering_m100,
Treordering_m110,
Treordering_m120,
Treordering_m130,
Treordering_m140,
Treordering_m150,
Treordering_m160,
Treordering_m170,
Treordering_m180,
Treordering_m190,
Treordering_m200
Treordering_m0,
Treordering_m5,
Treordering_m10,
Treordering_m15,
Treordering_m20,
Treordering_m25,
Treordering_m30,
Treordering_m35,
Treordering_m40,
Treordering_m45,
Treordering_m50,
Treordering_m55,
Treordering_m60,
Treordering_m65,
Treordering_m70,
0ms) ded Value
Treordering_m80,
Treordering_m85,
Treordering_m90,
Treordering_m95,
Treordering_m100,
Treordering_m110,
Treordering_m120,
Treordering_m130,
Treordering_m140,
Treordering_m150,
Treordering_m160,
Treordering_m170,
Treordering_m180,
Treordering_m190,
Treordering_m200
PdcpSnsize_7bits, PdcpSnsize_12bits( Default/Recommen

PdcpSnsize_12bits 12 bits) ded Value
RlcSnSize_size5, RlcSnSize_size10(1 Default/Recommen
RlcSnSize_size10 0bits) ded Value
RlcSnSize_size5, RlcSnSize_size10(1 Default/Recommen

RlcSnSize_size10 0bits) ded Value
Treordering_m0,
Treordering_m5,
Treordering_m10,
Treordering_m15,
Treordering_m20,
Treordering_m25,
Treordering_m30,
Treordering_m35,
Treordering_m40,
Treordering_m45,
Treordering_m50,
Treordering_m55,
Treordering_m60,
Treordering_m65,
Treordering_m70,
0ms) ded Value
Treordering_m80,
Treordering_m85,
Treordering_m90,
Treordering_m95,
Treordering_m100,
Treordering_m110,
Treordering_m120,
Treordering_m130,
Treordering_m140,
Treordering_m150,
Treordering_m160,
Treordering_m170,
Treordering_m180,
Treordering_m190,
Treordering_m200
Treordering_m0,
Treordering_m5,
Treordering_m10,
Treordering_m15,
Treordering_m20,
Treordering_m25,
Treordering_m30,
Treordering_m35,
Treordering_m40,
Treordering_m45,
Treordering_m50,
Treordering_m55,
Treordering_m60,
Treordering_m65,
Treordering_m70,
0ms) ded Value
Treordering_m80,
Treordering_m85,
Treordering_m90,
Treordering_m95,
Treordering_m100,
Treordering_m110,
Treordering_m120,
Treordering_m130,
Treordering_m140,
Treordering_m150,
Treordering_m160,
Treordering_m170,
Treordering_m180,
Treordering_m190,
Treordering_m200
Default/Recommen
FALSE, TRUE TRUE(TRUE) TRUE(TRUE) RlcPdcpParaGroup
ded Value
QCI1, QCI2, QCI3,
QCI4, QCI5, QCI6, None None Engineering Design StandardQci
QCI7, QCI8, QCI9
QCI6: 1000
QCI7: 900
0.001~1, step:0.001 700 Engineering Design StandardQci
QCI8: 800
QCI9: 700
QCI6: 1000
QCI7: 900
0.001~1, step:0.001 700 Engineering Design StandardQci
QCI8: 800
QCI9: 700
MinGbrRate_0_KB,
MinGbrRate_1_KB,
MinGbrRate_2_KB,
MinGbrRate_4KB,
MinGbrRate_8_KB,
MinGbrRate_16_K
B,
MinGbrRate_32_K
B, Engineering Design StandardQci
1KB/s) 1KB/s)
MinGbrRate_64_K
B,
MinGbrRate_128_K
B,
MinGbrRate_256_K
B,
MinGbrRate_512_K
B
MinGbrRate_0_KB,
MinGbrRate_1_KB,
MinGbrRate_2_KB,
MinGbrRate_4KB,
MinGbrRate_8_KB,
MinGbrRate_16_K
B,
MinGbrRate_32_K
B, Engineering Design StandardQci
1KB/s) 1KB/s)
MinGbrRate_64_K
B,
MinGbrRate_128_K
B,
MinGbrRate_256_K
B,
MinGbrRate_512_K
B
0~1, step:0.1 10 10 Engineering Design StandardQci
0~39 0 None Engineering Design StandardQci
0~39 0 None Engineering Design StandardQci
PBR_0_KBps,
PBR_8_KBps,
PBR_16_KBps,
PBR_32_KBps, PBR_8_KBps(8KB/ PBR_8_KBps(8KB/
Engineering Design StandardQci
PBR_64_KBps, s) s)
PBR_128_KBps,
PBR_256_KBps,
PBR_INFINITY
QCI 6: 9
QCI 7: 10
9~16 11 Engineering Design StandardQci
QCI 8: 11
QCI 9: 12
FLOW_CTRL, FLOW_CTRL(Flow
None Engineering Design StandardQci
NON_FLOW_CTRL Control)
CLASS_0,
CLASS_1(CLASS_ CLASS_1(CLASS_ Default/Recommen
CLASS_1, AlgoDefaultPara
1) 1) ded Value
CLASS_2
NO_ADAPTIVE,
TxD_BF_ADAPTIV MIMO_BF_ADAPTI MIMO_BF_ADAPTI
BfMimoAdaptivePar
E, VE(MIMO_BF_ADA VE(MIMO_BF_ADA Engineering Design
aCfg
MIMO_BF_ADAPTI PTIVE) PTIVE)
VE
TM2, TM3, TM7, BfMimoAdaptivePar
TM3(TM3) TM3(TM3) Engineering Design
TM8, TM4 aCfg
OFF, ON ON(On) ON(On) Engineering Design CqiAdaptiveCfg

ms2, ms5, ms10,
ms20, ms32, ms40,
ms40(40ms) ms40(40ms) Engineering Design CqiAdaptiveCfg
ms64, ms80,
ms128, ms160
NO_ADAPTIVE,
OL_ADAPTIVE, OL_ADAPTIVE(OL OL_ADAPTIVE(OL MimoAdaptivePara
Engineering Design
CL_ADAPTIVE, _ADAPTIVE) _ADAPTIVE) Cfg
OC_ADAPTIVE
TM2, TM3, TM4, MimoAdaptivePara
TM3(TM3) TM3(TM3) Engineering Design
TM6 Cfg
OFF, ON ON(On) ON(On) Engineering Design SrsAdaptiveCfg

ms5, ms10, ms20,
ms40(40ms) ms40(40ms) Engineering Design SrsAdaptiveCfg
ms40
QCI1, QCI2, QCI3,

QCI4, QCI5, QCI6, None None Engineering Design TypDrbBsr
QCI7, QCI8, QCI9
TPeriodBSRTimer_
sf5,
TPeriodBSRTimer_
sf10,
TPeriodBSRTimer_
sf16,
TPeriodBSRTimer_
sf20,
TPeriodBSRTimer_
sf32,
TPeriodBSRTimer_
sf40,
TPeriodBSRTimer_
sf64,
TPeriodBSRTimer_ TPeriodBSRTimer_ Default/Recommen
None TypDrbBsr
sf80, sf10(10 subframes) ded Value
TPeriodBSRTimer_
sf128,
TPeriodBSRTimer_
sf160,
TPeriodBSRTimer_
sf320,
TPeriodBSRTimer_
sf640,
TPeriodBSRTimer_
sf1280,
TPeriodBSRTimer_
sf2560,
TPeriodBSRTimer_i
nfinity
sf320, sf640,
Default/Recommen
sf1280, sf2560, sf320(sf320) None TypDrbBsr
ded Value
sf5120, sf10240
GAP_PATTERN_T
YPE_1, GAP_PATTERN_T GAP_PATTERN_T Default/Recommen
HoMeasComm
GAP_PATTERN_T YPE_1 YPE_1 ded Value
YPE_2
FC0, FC1, FC2,

FC3, FC4, FC5,
Default/Recommen
FC6, FC7, FC8, FC6 FC6 HoMeasComm
ded Value
FC9, FC11, FC13,
FC15, FC17, FC19
FC0, FC1, FC2,
FC3, FC4, FC5,
Default/Recommen
ded Value
FC9, FC11, FC13,
FC15, FC17, FC19
FC0, FC1, FC2,

FC3, FC4, FC5,
Default/Recommen
ded Value
FC9, FC11, FC13,
FC15, FC17, FC19
Default/Recommen
NOT_CFG, CFG NOT_CFG NOT_CFG HoMeasComm
ded Value
Default/Recommen
-141~-43 -44 -44 HoMeasComm
ded Value
Default/Recommen
NOT_CFG, CFG NOT_CFG NOT_CFG HoMeasComm
ded Value
T_CRMAX_30S,
T_CRMAX_60S,
T_CRMAX_60S(60 T_CRMAX_60S(60 Default/Recommen
T_CRMAX_120S, HoMeasComm
s) s) ded Value
T_CRMAX_180S,
T_CRMAX_240S
T_CRMAXHYST_3
0S,
T_CRMAXHYST_6
0S,
T_CRMAXHYST_1 T_CRMAXHYST_6 T_CRMAXHYST_6 Default/Recommen
HoMeasComm
20S, 0S(60s) 0S(60s) ded Value
T_CRMAXHYST_1
80S,
T_CRMAXHYST_2
40S
Default/Recommen
1~16 4 4 HoMeasComm
ded Value
Default/Recommen
1~16 8 8 HoMeasComm
ded Value
TTT_SF_MEDIUM_
0DOT25,
TTT_SF_MEDIUM_
0DOT50, TTT_SF_MEDIUM_ TTT_SF_MEDIUM_ Default/Recommen
HoMeasComm
TTT_SF_MEDIUM_ LDOT0(1) LDOT0(1) ded Value
0DOT75,
TTT_SF_MEDIUM_
LDOT0
TTT_SF_HIGH_0D
OT25,
TTT_SF_HIGH_0D
OT50, TTT_SF_HIGH_0D TTT_SF_HIGH_0D Default/Recommen
HoMeasComm
TTT_SF_HIGH_0D OT75(0.75) OT75(0.75) ded Value
OT75,
TTT_SF_HIGH_LD
OT0
FC0, FC1, FC2,

FC3, FC4, FC5,
Default/Recommen
ded Value
FC9, FC11, FC13,
FC15, FC17, FC19
FC0, FC1, FC2,

FC3, FC4, FC5,
Default/Recommen
ded Value
FC9, FC11, FC13,
FC15, FC17, FC19
Default/Recommen
1~8 4 4 InterRatHoComm
ded Value
r1, r2, r4, r8, r16, Default/Recommen

Infinity(Infinity) infinity(Infinity) InterRatHoComm
r32, r64, Infinity ded Value
120ms, 240ms,
480ms, 640ms,
480ms 480ms InterRatHoComm
1min, 6min, 12min,
30min, 60min
UTRAN_RSCP,
Default/Recommen
UTRAN_ECN0, UTRAN_RSCP UTRAN_RSCP InterRatHoComm
ded Value
UTRAN_BOTH
120ms, 240ms,
480ms, 640ms,
1min, 6min, 12min,
30min, 60min
PILOT_STRENGTH
, Default/Recommen
PILOT_STRENGTH PILOT_STRENGTH InterRatHoComm
PILOT_PN_PHASE ded Value
_AND_STRENGTH
120ms, 240ms,
480ms, 640ms,
1min, 6min, 12min,
30min, 60min
Default/Recommen
PILOT_STRENGTH PILOT_STRENGTH PILOT_STRENGTH InterRatHoComm
ded Value
120ms, 240ms,
480ms, 640ms,
1024ms, 2048ms,
480ms 480ms Engineering Design InterRatHoComm
5120ms, 10240ms,
1min, 6min, 12min,
30min, 60min
RSRP, RSRQ, Default/Recommen

RSRP RSRP InterRatHoComm
BOTH ded Value
Default/Recommen
EventB1, EventB2 EventB1(EventB1) EventB1(EventB1) InterRatHoComm
ded Value
Default/Recommen
1~8 4 4 IntraRatHoComm
ded Value

Infinity(Infinity) infinity(Infinity) IntraRatHoComm
Default/Recommen
RSRP, RSRQ RSRP RSRP IntraRatHoComm
ded Value
SAME_AS_TRIG_ SAME_AS_TRIG_
SAME_AS_TRIG_ Default/Recommen
QUAN(Same as QUAN(Same as IntraRatHoComm
QUAN, BOTH ded Value
Trig Quan) Trig Quan)
120ms, 240ms,
480ms, 640ms,
240ms 240ms IntraRatHoComm
1min, 6min, 12min,
30min, 60min
QUAN(Same as QUAN(Same as IntraRatHoComm
120ms, 240ms,
480ms, 640ms,
240ms 240ms IntraRatHoComm
1min, 6min, 12min,
30min, 60min
RSRP RSRP IntraRatHoComm
BOTH ded Value

BOTH ded Value

BOTH ded Value
Radio Planning
0~17 None None CSFallBackHo
(Internal planning)
0ms, 40ms, 64ms,

80ms, 100ms,
128ms, 160ms,
256ms, 320ms, Radio Planning
40ms 40ms CSFallBackHo
480ms, 512ms, (Internal planning)
640ms, 1024ms,
1280ms, 2560ms,
5120ms
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
640ms, 1024ms,
1280ms, 2560ms,
5120ms
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
640ms, 1024ms,
1280ms, 2560ms,
5120ms
Radio Planning
-120~-25 -106 -106 CSFallBackHo
(Internal planning)
Radio Planning
-24~0, step:0.5 -13 -13 CSFallBackHo
(Internal planning)
Radio Planning
-110~-48 -103 -103 CSFallBackHo
(Internal planning)
Default/Recommen
-31.5~0, step:0.5 -34 -34 CSFallBackHo
ded Value
Radio Planning
0~17 None None CellAcBar
(Internal planning)
NOT_CFG(Not NOT_CFG(Not
NOT_CFG, CFG Engineering Design CellAcBar
configure) configure)
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE(

Engineering Design CellAcBar
BOOLEAN_TRUE False) False)
P00, P05, P10,

P15, P20, P25,
Default/Recommen
P30, P40, P50, P95(95%) P95(95%) CellAcBar
ded Value
P60, P70, P75,
P80, P85, P90, P95
ACCESS_BARRIN
G_TIME_S4,
ACCESS_BARRIN
G_TIME_S8,
ACCESS_BARRIN
G_TIME_S16,
ACCESS_BARRIN
G_TIME_S32, ACCESS_BARRIN ACCESS_BARRIN Default/Recommen
CellAcBar
ACCESS_BARRIN G_TIME_S4(4s) G_TIME_S4(4s) ded Value
G_TIME_S64,
ACCESS_BARRIN
G_TIME_S128,
ACCESS_BARRIN
G_TIME_S256,
ACCESS_BARRIN
G_TIME_S512
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( Default/Recommen

CellAcBar
BOOLEAN_TRUE False) False) ded Value
CellAcBar

CellAcBar
CellAcBar

CellAcBar
P00, P05, P10,
P15, P20, P25,
Default/Recommen
P30, P40, P50, P95(95%) P95(95%) CellAcBar
ded Value
P60, P70, P75,
P80, P85, P90, P95
ACCESS_BARRIN
G_TIME_S4,
ACCESS_BARRIN
G_TIME_S8,
ACCESS_BARRIN
G_TIME_S16,
ACCESS_BARRIN
G_TIME_S32, ACCESS_BARRIN ACCESS_BARRIN Default/Recommen
CellAcBar
ACCESS_BARRIN G_TIME_S4(4s) G_TIME_S4(4s) ded Value
G_TIME_S64,
ACCESS_BARRIN
G_TIME_S128,
ACCESS_BARRIN
G_TIME_S256,
ACCESS_BARRIN
G_TIME_S512
CellAcBar

CellAcBar
CellAcBar

CellAcBar
CellAcBar
Radio Planning
0~17 None None CellAccess
(Internal planning)
CELL_BARRED,
CELL_NOT_BARR CELL_NOT_BARR Default/Recommen
CELL_NOT_BARR CellAccess
ED(Not Barred) ED(Not Barred) ded Value
ED
CELL_RESERVED, CELL_NOT_RESE CELL_NOT_RESE
Default/Recommen
CELL_NOT_RESE RVED(Not RVED(Not CellAccess
ded Value
RVED Reserved) Reserved)
ALLOWED, Default/Recommen
ALLOWED ALLOWED CellAccess
NOT_ALLOWED ded Value
NORMAL_MODE, NORMAL_MODE(N NORMAL_MODE(N Default/Recommen
CellAccess
RR_MODE ormal mode) ormal mode) ded Value
Default/Recommen
1~720 1 1 CellAccess
ded Value
Radio Planning
0~17 None None CellOp
(Internal planning)
Radio Planning
0~65535 None None CellOp
(Internal planning)
CELL_RESERVED
CELL_NOT_RESE CELL_NOT_RESE
_FOR_OP, Default/Recommen
RVED_FOR_OP(N RVED_FOR_OP(N CellOp
CELL_NOT_RESE ded Value
ot Reserved) ot Reserved)
RVED_FOR_OP
Default/Recommen
1~100 16 16 CellOp
ded Value
Default/Recommen
1~100 16 16 CellOp
ded Value
0~3 None None N/A CellOp
Radio Planning
0~17 None None CellResel
(Internal planning)
DB0_Q_HYST,
DB1_Q_HYST,
DB2_Q_HYST,
DB3_Q_HYST,
DB4_Q_HYST,
DB5_Q_HYST,
DB6_Q_HYST,
DB8_Q_HYST, Default/Recommen
DB4_Q_HYST(4dB) DB4_Q_HYST(4dB) CellResel
DB10_Q_HYST, ded Value
DB12_Q_HYST,
DB14_Q_HYST,
DB16_Q_HYST,
DB18_Q_HYST,
DB20_Q_HYST,
DB22_Q_HYST,
DB24_Q_HYST
NOT_CFG, CFG CFG(Configure) CFG(Configure) Engineering Design CellResel

S30_T_EVALULATI
ON,
S60_T_EVALULATI
ON,
S120_T_EVALULA S60_T_EVALULATI S60_T_EVALULATI Default/Recommen
CellResel
TION, ON(60s) ON(60s) ded Value
S180_T_EVALULA
TION,
S240_T_EVALULA
TION
S30_T_HYST_NOR
MAL,
S60_T_HYST_NOR
MAL,
S120_T_HYST_NO S30_T_HYST_NOR S30_T_HYST_NOR Default/Recommen
CellResel
RMAL, MAL(30s) MAL(30s) ded Value
S180_T_HYST_NO
RMAL,
S240_T_HYST_NO
RMAL
Default/Recommen
1~16 4 4 CellResel
ded Value
Default/Recommen
1~16 8 8 CellResel
ded Value
DB_6_Q_HYST_SF
_MEDIUM,
DB_4_Q_HYST_SF
_MEDIUM, DB0_Q_HYST_SF_ DB0_Q_HYST_SF_ Default/Recommen
CellResel
DB_2_Q_HYST_SF MEDIUM(0dB) MEDIUM(0dB) ded Value
_MEDIUM,
DB0_Q_HYST_SF_
MEDIUM
DB_6_Q_HYST_SF
_HIGH,
DB_4_Q_HYST_SF
_HIGH, DB0_Q_HYST_SF_ DB0_Q_HYST_SF_ Default/Recommen
CellResel
DB_2_Q_HYST_SF HIGH(0dB) HIGH(0dB) ded Value
_HIGH,
DB0_Q_HYST_SF_
HIGH

Default/Recommen
0~62, step:2 10 10 CellResel
ded Value
Default/Recommen
ded Value
Default/Recommen
0~7 7 7 CellResel
ded Value
Default/Recommen
-140~-44, step:2 -64 -64 CellResel
ded Value
NOT_CFG, CFG Engineering Design CellResel
Default/Recommen
-30~33 23 23 CellResel
ded Value
Default/Recommen
ded Value
MBW6, MBW15,
DL bandwidth of the Radio Planning
MBW25, MBW50, MBW6(1.4M) CellResel
serving cell (Internal planning)
MBW75, MBW100
Default/Recommen
0~7 1 1 CellResel
ded Value
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
T5, T_RESEL_SF_1DO T_RESEL_SF_1DO Default/Recommen
CellResel
T_RESEL_SF_0DO T0(1.0) T0(1.0) ded Value
T75,
T_RESEL_SF_1DO
T0
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
CellResel
T75,
T_RESEL_SF_1DO
T0
BitString00,
BitString01, Default/Recommen
BitString01(01) BitString01(01) CellResel
BitString10, ded Value
BitString11

Engineering Design CellResel
Default/Recommen
0~31 5 5 CellResel
ded Value
Default/Recommen
0~31 4 4 CellResel
ded Value
Default/Recommen
0~31 0 0 CellResel
ded Value
Default/Recommen
-34~-3 -18 -18 CellResel
ded Value
Radio Planning CellReselCdma200

0~17 None None
(Internal planning) 0
NOT_CFG(Not NOT_CFG(Not CellReselCdma200

NOT_CFG, CFG Engineering Design
configure) configure) 0
BOOLEAN_FALSE, BOOLEAN_TRUE( BOOLEAN_TRUE( CellReselCdma200
Engineering Design
BOOLEAN_TRUE True) True) 0

CellReselCdma200
0~15 1 1 Engineering Design
0

BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( CellReselCdma200
Engineering Design
BOOLEAN_TRUE False) False) 0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
T5, T_RESEL_SF_0DO T_RESEL_SF_0DO Default/Recommen CellReselCdma200
T_RESEL_SF_0DO T75(0.75) T75(0.75) ded Value 0
T75,
T_RESEL_SF_1DO
T0
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
T75,
T_RESEL_SF_1DO
T0

CellReselCdma200
0
CellReselCdma200
0

Engineering Design
Engineering Design

Engineering Design
Engineering Design

Engineering Design
Engineering Design

Engineering Design
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0

CellReselCdma200
0~6 characters NULL None Engineering Design
0

CellReselCdma200
0

T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
T75,
T_RESEL_SF_1DO
T0
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
T75,
T_RESEL_SF_1DO
T0

CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
CellReselCdma200
0
Radio Planning
0~17 None None CellReselGeran
(Internal planning)
Default/Recommen
0~7 1 1 CellReselGeran
ded Value
NOT_CFG, CFG Engineering Design CellReselGeran
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
CellReselGeran
T75,
T_RESEL_SF_1DO
T0
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
CellReselGeran
T75,
T_RESEL_SF_1DO
T0
Radio Planning
0~17 None None CellReselUtran
(Internal planning)
Default/Recommen
0~7 1 1 CellReselUtran
ded Value
NOT_CFG, CFG Engineering Design CellReselUtran
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
CellReselUtran
T75,
T_RESEL_SF_1DO
T0
T_RESEL_SF_0DO
T25,
T_RESEL_SF_0DO
CellReselUtran
T75,
T_RESEL_SF_1DO
T0
Radio Planning
0~17 None None CellSel
(Internal planning)
Default/Recommen
-140~-44, step:2 -64 -64 CellSel
ded Value
Default/Recommen
0~16, step:2 0 0 CellSel
ded Value
Default/Recommen
-34~-3 -18 -18 CellSel
ded Value
NOT_CFG(Not NOT_CFG(Not Default/Recommen

NOT_CFG, CFG CellSel
configure) configure) ded Value
1~8 1 None Engineering Design CellSel

Radio Planning
0~17 None None CellSiMap
(Internal planning)
BOOLEAN_FALSE, BOOLEAN_TRUE( BOOLEAN_TRUE(

Engineering Design CellSiMap
BOOLEAN_TRUE True) True)
RF8, RF16, RF32,

RF16(16 radio RF16(16 radio Default/Recommen
RF64, RF128, CellSiMap
frames) frames) ded Value
RF256, RF512
RF8, RF16, RF32,
RF256, RF512
RF8, RF16, RF32,

RF256, RF512
RF8, RF16, RF32,

RF256, RF512
RF8, RF16, RF32,
RF256, RF512
RF8, RF16, RF32,

RF256, RF512
RF8, RF16, RF32,

RF256, RF512
RF8, RF16, RF32,
RF256, RF512
RF8, RF16, RF32,

RF256, RF512
Default/Recommen
1~300 6 6 CellSiMap
ded Value
Default/Recommen
MERGE, DISCARD DISCARD DISCARD CellSiMap
ded Value
Default/Recommen
MERGE, DISCARD DISCARD DISCARD CellSiMap
ded Value
Radio Planning
0~17 None None CellUlpcComm
(Internal planning)
AL0, AL04, AL05,
Default/Recommen
AL06, AL07, AL08, AL07(0.7) AL07(0.7) CellUlpcComm
ded Value
AL09, AL1
Default/Recommen
-127~-96 -105 -105 CellUlpcComm
ded Value
Default/Recommen
-126~24 -67 -67 CellUlpcComm
ded Value
DELTAF_2,
Default/Recommen
DELTAF0, DELTAF0(0dB) DELTAF0(0dB) CellUlpcComm
ded Value
DELTAF2
DELTAF1,
Default/Recommen
ded Value
DELTAF5
DELTAF_2,
DELTAF0, Default/Recommen
DELTAF1(1dB) DELTAF1(1dB) CellUlpcComm
DELTAF1, ded Value
DELTAF2
DELTAF_2,
Default/Recommen
ded Value
DELTAF2
DELTAF_2,
Default/Recommen
ded Value
DELTAF2
Default/Recommen
-2~12, step:2 4 4 CellUlpcComm
ded Value
Radio Planning eNBCellOpRsvdPar

0~17 None None
(Internal planning) a
Radio Planning eNBCellOpRsvdPar
0~65535 None None
(Internal planning) a
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
ameter0_bit16:Off, Default/Recommen eNBCellOpRsvdPar
RsvdSwPara0_bit1 None
ReservedSwitchPar ded Value a
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
ameter1_bit16:Off, Default/Recommen eNBCellOpRsvdPar
RsvdSwPara1_bit1 None
ReservedSwitchPar ded Value a
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
Default/Recommen eNBCellOpRsvdPar
RsvdSwPara2_bit1 None None
ded Value a
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
0~4294967295 0 None
ded Value a
0~4294967295 0 None
ded Value a
0~4294967295 0 None
ded Value a
0~4294967295 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~65535 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
0~255 0 None
ded Value a
TimeAlignmentTime
0~17 None None N/A
r
If the long DRX

cycle length is
SF500, SF750, required to be
SF1280, SF1920, SF1920(1920 greater than or TimeAlignmentTime
N/A
SF2560, SF5120, subframes) equal to 80 ms, it is r
SF10240, INFINITY recommended that
this parameter be
set to SF2560.
Radio Planning
0~17 None None UeTimerConst
(Internal planning)
MS100_T300,
MS200_T300,
MS300_T300,
MS400_T300, MS200_T300(200m MS200_T300(200m Default/Recommen
UeTimerConst
MS600_T300, s) s) ded Value
MS1000_T300,
MS1500_T300,
MS2000_T300
MS100_T301,
MS200_T301,
MS300_T301,
MS400_T301, MS200_T301(200m MS200_T301(200m Default/Recommen
UeTimerConst
MS600_T301, s) s) ded Value
MS1000_T301,
MS1500_T301,
MS2000_T301
MS0_T310,
MS50_T310,
MS100_T310,
MS1000_T310(100 MS1000_T310(100 Default/Recommen
MS200_T310, UeTimerConst
0ms) 0ms) ded Value
MS500_T310,
MS1000_T310,
MS2000_T310
MS1000_T311,
MS3000_T311,
MS5000_T311,
MS10000_T311(10 MS10000_T311(10 Default/Recommen
MS10000_T311, UeTimerConst
000ms) 000ms) ded Value
MS15000_T311,
MS20000_T311,
MS30000_T311
n1, n2, n3, n4, n5, Default/Recommen
n1(1) n1(1) UeTimerConst
n6, n8, n10 ded Value
n1, n2, n3, n4, n6, Default/Recommen

n10(10) n10(10) UeTimerConst
n8, n10, n20 ded Value
Radio Planning
0~17 None None Cell
(Internal planning)
Radio Planning
1~99 characters None None Cell
(Internal planning)
Radio Planning
0~17 None None Cell
(Internal planning)
Engineering Design Cell
NORMAL_CP, NORMAL_CP(Nor NORMAL_CP(Nor Radio Planning

Cell
EXTENDED_CP mal) mal) (Internal planning)
NORMAL_CP, NORMAL_CP(Nor NORMAL_CP(Nor Radio Planning
Cell
EXTENDED_CP mal) mal) (Internal planning)
Radio Planning
1~43,61~64 None None Cell
(Internal planning)
NOT_CFG, CFG Cell
18000~45589,6443 Radio Planning

18000 None Cell
6~65535 (Internal planning)
0~45589,64436~65 Radio Planning

None None Cell
CELL_BW_N6,
CELL_BW_N15,
CELL_BW_N25, Radio Planning
None None Cell
CELL_BW_N50, (Internal planning)
CELL_BW_N75,
CELL_BW_N100
CELL_BW_N6,
CELL_BW_N15,
CELL_BW_N25, Radio Planning
None None Cell
CELL_BW_N50, (Internal planning)
CELL_BW_N75,
CELL_BW_N100
Radio Planning
0~255 None None Cell
(Internal planning)
Radio Planning
0~503 None None Cell
(Internal planning)
Default/Recommen
1~32 1 1 Cell
ded Value
CELL_DEACTIVE, CELL_DEACTIVE( CELL_DEACTIVE( Default/Recommen

Cell
CELL_ACTIVE Deactivated) Deactivated) ded Value
CELL_UNBLOCK,
CELL_HIGH_BLOC
K,
CELL_UNBLOCK(U CELL_UNBLOCK(U
CELL_MIDDLE_BL Engineering Design Cell
nblock) nblock)
OCK,
CELL_LOW_BLOC
K
Default/Recommen
1~1440 60 60 Cell
ded Value
CELL_FDD, Radio Planning
None None Cell
CELL_TDD (Internal planning)
SA0, SA1, SA2,
Radio Planning
SA3, SA4, SA5, SA0(SA0) None Cell
(Internal planning)
SA6
SSP0, SSP1,
SSP2, SSP3, Radio Planning
SSP0(SSP0) None Cell
SSP4, SSP5, (Internal planning)
SSP6, SSP7, SSP8
dB-24, dB-22, dB-
20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
dB-1, dB0, dB1, dB0(0dB) dB0(0dB) Engineering Design Cell
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
dB-24, dB-22, dB-

20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
dB-1, dB0, dB1, dB0(0dB) dB0(0dB) Engineering Design Cell
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
on the network
plan. The tool for
configuring Zadoff-
Chu (ZC) root
sequences is
recommended.
During manual
configuration, the
following rules
apply:
1. If two
neighboring cells
use the same or
overlapping time-
frequency
resources for the
physical random
access channel
Radio Planning
0~837 None (PRACH), they Cell
(Internal planning)
must have different
values of this
parameter.
Note: When
manually
configuring root ZC
sequences, ensure
that both the first
logical root
sequence and each
subsequent logical
root sequence are
within the specified
value range. For
details about how to
calculate the
number of ZC root
sequences required
LOW_SPEED,
HIGH_SPEED,
ULTRA_HIGH_SPE LOW_SPEED(Low LOW_SPEED(Low
Engineering Design Cell
ED, speed cell flag) speed cell flag)
EXTRA_HIGH_SPE
ED
Preamble format 0 Default/Recommen
0~4 0 Cell
is applicable. ded Value
Radio Planning
1~100000 10000 10000 Cell
(Internal planning)
NOT_CFG(Not NOT_CFG(Not Radio Planning
NOT_CFG, CFG Cell
configure) configure) (Internal planning)
4.8~5.0,9.6~10.0,1
Radio Planning
4.6~15.0,18.3~20.0 98 98 Cell
(Internal planning)
, step:0.1
4.8~5.0,9.6~10.0,1
Radio Planning
4.6~15.0,18.3~20.0 98 98 Cell
(Internal planning)
, step:0.1

NOT_CFG, CFG Cell
Radio Planning
0~16777215 0 None Cell
(Internal planning)
NOT_CFG(Not
NOT_CFG, CFG None N/A Cell
configure)
-30~36 23 23 N/A Cell

BOOLEAN_FALSE, BOOLEAN_FALSE( Radio Planning
None Cell
BOOLEAN_TRUE False) (Internal planning)
SFN,
CELL_COMBINATI
ON,
Radio Planning
TWO_RRU_COMBI SFN(SFN) None Cell
(Internal planning)
NATION,
DIGITAL_COMBINA
TION
NO_COMPRESSIO
N, NO_COMPRESSIO Radio Planning
None Cell
NORMAL_COMPR N(No Compression) (Internal planning)
ESSION
CELL_INST_UNIN
STALL,
CELL_INST_UEM_
CFGING,
CELL_INST_RRU_
CFGING,
CELL_INST_BBI_C
FGING,
CELL_INST_RECF
GING,
None None N/A Cell
CELL_INST_DELE
TING,
CELL_INST_NORM
AL,
CELL_INST_BARR
ED,
CELL_INST_ALLO
CATING_RES,
CELL_INST_CRM_
CFGING
RT_BY_RRU,
CCEM_CELLBASI
C_CARRIER_RES
OURCE_ALLOC_F
AIL,
CCEM_CELLBASI
C_BASEBAND_RE
SOURCE_ALLOC_
FAIL,
CCEM_CELLBASI
C_CARRIER_RES
OURCE_CFG_FAIL
,
CCEM_CELLBASI
C_ERR_TDD_MIM
O_NOT_SUPPORT
_8T8R,
CCEM_CELLBASI
C_ERR_CR_UL_F None None N/A Cell
REQ_ACT_FAIL,
CCEM_CELLBASI
C_ERR_CR_DL_F
REQ_ACT_FAIL,
CCEM_CELLBASI
C_ERR_CR_POW
ER_ACT_FAIL,
CCEM_CELLBASI
C_ERR_CR_DL_F
REQ_POWER_AC
T_FAIL,
CCEM_CELLBASI
C_ERR_SET_RRU
_FREQ_FAIL,
CCEM_CELLBASI
C_ERR_CPRI_BW
_NOT_ENOUGH,
CCEM_CELLBASI
0~32 characters None None N/A Cell

CELL_NO_OP,
CELL_SETUP_ACT
,
CELL_SETUP_UBL
,
CELL_SETUP_HE
ALCHK,
CELL_SETUP_141,
CELL_SETUP_UL
WIDESCAN,
CELL_DEL_BLK_L
OW,
CELL_DEL_BLK_M
ID,
CELL_DEL_BLK_H
IGH,
None None N/A Cell
CELL_DEL_NOUS
ER,
CELL_DEL_DEA,
CELL_DEL_RMV,
CELl_DEL_HEALC
HK,
CELL_DEL_UNHE
AL,
CELL_DEL_SETUP
_FAIL,
CELL_DEL_141_D
EL,
CELL_DEL_ULWID
ESCAN,
CELL_DEL_CELLN
OACCESSALM
0~32 characters None None N/A Cell

CELL_NO_OP,
CELL_SETUP_ACT
,
CELL_SETUP_UBL
,
CELL_SETUP_HE
ALCHK,
CELL_SETUP_141,
CELL_SETUP_UL
WIDESCAN,
CELL_DEL_BLK_L
OW,
CELL_DEL_BLK_M
ID,
CELL_DEL_BLK_H
IGH,
None None N/A Cell
CELL_DEL_NOUS
ER,
CELL_DEL_DEA,
CELL_DEL_RMV,
CELl_DEL_HEALC
HK,
CELL_DEL_UNHE
AL,
CELL_DEL_SETUP
_FAIL,
CELL_DEL_141_D
EL,
CELL_DEL_ULWID
ESCAN,
CELL_DEL_CELLN
OACCESSALM
CELL_PWRSAVE_
UNINSTALL,
CELL_PWRSAVE_
RFSHD,
CELL_PWRSAVE_
CELLSHD,
CELL_PWRSAVE_
LOWPWR_CELLU
SEDPWRRDU,
CELL_PWRSAVE_
LOWPWR_RSPWR
None None N/A Cell
RDU,
CELL_PWRSAVE_
LOWPWR_RFSHD,
CELL_PWRSAVE_
LOWPWR_CELLS
HD,
AUTO_PWROFF_
ONTIME,
CELL_PWRSAVE_I
NTERRAT_CELLS
HD
BBI_SLOT_0,
BBI_SLOT_1,
BBI_SLOT_2,
BBI_SLOT_3,
None None N/A Cell
BBI_SLOT_4,
BBI_SLOT_5,
BBI_SLOT_INVALI
D
BASIC_TYPE,
TWO_RRU_COMBI
NATION_TYPE,
SFN_TYPE,
BF_TYPE,
MIMO_HELP_TYP
None None N/A Cell
E,
CELL_COMBINATI
ON_TYPE,
DIGITAL_COMBINA
TION_TYPE,
INVALID_TYPE
0~62 None None N/A Cell
UNINSTALL,
SYMBOL_SHUTDO None None N/A Cell
WN

Radio Planning
0~17 None None CellBf
(Internal planning)
SINGLE_LAYER_B
SINGLE_LAYER_B
F, None Engineering Design CellBf
F(Single-Layer BF)
DUAL_LAYER_BF
Radio Planning
0~17 None None CellDLIcicMcPara
(Internal planning)
120ms, 240ms,
480ms, 640ms,
5120ms 5120ms CellDLIcicMcPara
1min, 6min, 12min,
30min, 60min
Default/Recommen
1~8 8 8 CellDLIcicMcPara
ded Value
Infinity(Infinity) Infinity(Infinity) CellDLIcicMcPara
QUAN(Same as QUAN(Same as CellDLIcicMcPara
Default/Recommen
RSRP, RSRQ RSRP RSRP CellDLIcicMcPara
ded Value
Default/Recommen
0~15, step:0.5 4 4 CellDLIcicMcPara
ded Value
0ms, 40ms, 64ms,

80ms, 100ms,
128ms, 160ms,
640ms 640ms CellDLIcicMcPara
640ms, 1024ms,
1280ms, 2560ms,
5120ms
Default/Recommen
-15~15, step:0.5 -13 -13 CellDLIcicMcPara
ded Value
Radio Planning
0~17 None None CellLowPower
(Internal planning)
OFF, ON OFF(Off) OFF(Off) Engineering Design CellLowPower

Default/Recommen
OFF, ON OFF(Off) OFF(Off) CellLowPower
ded Value
Default/Recommen
00:00:00~23:59:59 00:00:00 00:00:00 CellLowPower
ded Value
Default/Recommen
00:00:00~23:59:59 06:00:00 06:00:00 CellLowPower
ded Value
Default/Recommen
0~1440 120 120 CellLowPower
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
-10~0 -1 -1 CellLowPower
ded Value
Default/Recommen
ded Value
Radio Planning
0~17 None None CellMro
(Internal planning)
NOT_CFG(Not
NOT_CFG, CFG None Engineering Design CellMro
configure)
dB-24, dB-22, dB-
20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
dB-1, dB0, dB1, dB24(24dB) None Engineering Design CellMro
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
dB-24, dB-22, dB-

20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
dB-1, dB0, dB1, dB-24(-24dB) None Engineering Design CellMro
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
Radio Planning
0~17 None None CellRacThd
(Internal planning)
1~15 5 5 Engineering Design CellRacThd





Set the parameter
based on actual
service
requirements. The
recommended
values are
described as
follows:
FDD:
For a cell with a 5
MHz bandwidth, a
value in the range
of 0 to 3000 is
recommended;
0~9000 3000 For a cell with a 10 Engineering Design CellRacThd
MHz bandwidth, a
value in the range
of 0 to 3000 is
recommended;
For a cell with a 15
MHz bandwidth, a
value in the range
of 0 to 6000 is
recommended;
For a cell with a 20
MHz bandwidth, a
value in the range
of 0 to 6000 is
recommended;
Radio Planning
0~17 None None CellRfShutdown
(Internal planning)
OFF, ON OFF(Off) OFF(Off) Engineering Design CellRfShutdown
Default/Recommen
00:00:00~23:59:59 00:00:00 00:00:00 CellRfShutdown
ded Value
Default/Recommen
00:00:00~23:59:59 06:00:00 06:00:00 CellRfShutdown
ded Value
0~7 3 3 Engineering Design CellRfShutdown
Radio Planning
0~17 None None CellRicAlgo
(Internal planning)
The value OFF is

recommended if
there is no remote
interference to the
cell.
OFF, ON OFF(Off) Engineering Design CellRicAlgo
The value ON is
recommended if
there is remote
interference to the
cell.
The value 0 is
recommended if
there is no remote
interference to the
cell.
0~2 0 Engineering Design CellRicAlgo
The value 1 is
recommended if
there is remote
interference to the
cell.
Radio Planning
OFF, ON OFF(Off) OFF(Off) CellRicAlgo
(Internal planning)
Radio Planning
0~17 None None CellShutdown
(Internal planning)
OFF, ON OFF(Off) OFF(Off) Engineering Design CellShutdown

Default/Recommen
00:00:00~23:59:59 00:00:00 00:00:00 CellShutdown
ded Value
Default/Recommen
00:00:00~23:59:59 06:00:00 06:00:00 CellShutdown
ded Value
Default/Recommen
0~100 20 20 CellShutdown
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Radio Planning
0~17 None None CellULIcicMcPara
(Internal planning)
120ms, 240ms,
480ms, 640ms,
5120ms 5120ms CellULIcicMcPara
1min, 6min, 12min,
30min, 60min
Default/Recommen
1~8 8 8 CellULIcicMcPara
ded Value
Infinity(Infinity) Infinity(Infinity) CellULIcicMcPara
QUAN(Same as QUAN(Same as CellULIcicMcPara
Default/Recommen
RSRP, RSRQ RSRP RSRP CellULIcicMcPara
ded Value
Default/Recommen
0~15, step:0.5 4 4 CellULIcicMcPara
ded Value
0ms, 40ms, 64ms,
80ms, 100ms,
128ms, 160ms,
640ms 640ms CellULIcicMcPara
640ms, 1024ms,
1280ms, 2560ms,
5120ms
Default/Recommen
-15~15, step:0.5 -10 -10 CellULIcicMcPara
ded Value
Radio Planning
0~17 None None CellUlschAlgo
(Internal planning)
Scenario A: The
EPF policy is
recommended on
live networks.
Scenario B: The
MAX C/I policy is
recommended
when the operator
or Huawei desires
to verify the system
performance in
maximum
capacities.
ULSCH_STRATEG Scenario C: The PF
Y_EPF, policy is
ULSCH_STRATEG recommended
Y_MAX_CI, ULSCH_STRATEG when the operator Default/Recommen
CellUlschAlgo
ULSCH_STRATEG Y_EPF(EPF) or Huawei desires ded Value
Y_PF, to verify the system
ULSCH_STRATEG performance in
Y_RR scenarios where
the capacity,
coverage, and
fairness reach a
tradeoff.
Scenario D: The RR
policy is
recommended
when the operator
or Huawei desires
to verify that each
UE has an equal
opportunity to be
scheduled.
ADAPTIVE_HARQ_
SW_ON,
ADAPTIVE_HARQ_ ADAPTIVE_HARQ_
ADAPTIVE_HARQ_
SW_SEMI_ON(Se SW_SEMI_ON(Se Engineering Design CellUlschAlgo
SW_OFF,
miOn) miOn)
ADAPTIVE_HARQ_
SW_SEMI_ON
10 10 CellUlschAlgo
step:0.01 ded Value
Default/Recommen
0~100 50 50 CellUlschAlgo
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
HOPPING_OFF,
HOPPING_TYPE1,
HOPPING_OFF(Ho HOPPING_OFF(Ho Default/Recommen
HOPPING_TYPE2, CellUlschAlgo
pping off) pping off) ded Value
HOPPING_TYPE2_
RANDOM
Default/Recommen
ded Value
Default/Recommen
ded Value
Scenario A: The
recommended
value is 3 if the cell
serves a large
number of cell
center users Default/Recommen
2~3 2 CellUlschAlgo
(CCUs). ded Value
Scenario B: The
recommended
value is 2 in
commercial
networks.
Radio Planning
0~17 None None eNBCellRsvdPara
(Internal planning)
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
ameter0_bit16:Off, Default/Recommen
RsvdSwPara0_bit1 None eNBCellRsvdPara
ReservedSwitchPar ded Value
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
RsvdSwPara1_bit1 None eNBCellRsvdPara
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
Default/Recommen
RsvdSwPara2_bit1 None None eNBCellRsvdPara
ded Value
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
Default/Recommen
0~4294967295 0 None eNBCellRsvdPara
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Radio Planning InterRatCellShutdo

0~17 None None
(Internal planning) wn
InterRatCellShutdo
OFF, ON OFF(Off) None Engineering Design
wn
Default/Recommen InterRatCellShutdo
00:00:00~23:59:59 03:00:00 None
ded Value wn
00:00:00~23:59:59 05:00:00 None
ded Value wn
0~5000 20 None
ded Value wn
0~100 10 None
ded Value wn
0~100 10 None
ded Value wn
Radio Planning
0~17 None None CellAlgoSwitch
(Internal planning)
RachAdjSwitch:Off, RachAdjSwitch:Off
RachAdjSwitch,
HoRaSwitch:On, HoRaSwitch:On
HoRaSwitch,
UnsyncRaSwitch:O UnsyncRaSwitch:O
UnsyncRaSwitch, Engineering Design CellAlgoSwitch
n, n
MaksIdxSwitch,
MaksIdxSwitch:Off, MaksIdxSwitch:Off
BackOffSwitch
BackOffSwitch:Off BackOffSwitch:Off
SrsSubframeRecfS SrsSubframeRecfS SrsSubframeRecfS
Engineering Design CellAlgoSwitch
witch witch:On witch:On
In ultra-high-speed
scenarios, the
recommended
value of
PucchSwitch is
PucchSwitch PucchSwitch:On Engineering Design CellAlgoSwitch
OFF.
In other scenarios,
the recommended
value of
PucchSwitch is ON.
AqmAlgoSwitch AqmAlgoSwitch:Off AqmAlgoSwitch:Off Engineering Design CellAlgoSwitch
CqiAdjAlgoSwitch:O CqiAdjAlgoSwitch:O
CqiAdjAlgoSwitch,
n, n Engineering Design CellAlgoSwitch
StepVarySwitch
StepVarySwitch:Off StepVarySwitch:Off
OFF, ON OFF(Off) OFF(Off) Engineering Design CellAlgoSwitch
Dynamic Adjust Dynamic Adjust

DynAdjVoltSwitch Engineering Design CellAlgoSwitch
Voltage Switch:Off Voltage Switch:Off
dlCacSwitch:Off,
ulCacSwitch:Off,
DlSwitch:Off
dlCacPredictSwitch:
UlSwitch:Off
DlSwitch, UlSwitch, Off,
DlPredictSwitch:Off
DlPredictSwitch, ulCacPredictSwitch:
UlPredictSwitch:Off
UlPredictSwitch, Off,
GbrUsageSwitch:Of
GbrUsageSwitch, GbrUsedPRbCheck
f Engineering Design CellAlgoSwitch
DlLdcSwitch, Switch:Off,
DlLdcSwitch:Off
UlLdcSwitch, dlLdcSwitch:Off,
UlLdcSwitch:Off
RelDrbSwitch, ulLdcSwitch:Off,
RelDrbSwitch:Off
PreemptionSwitch LdcDrbRelSwitch:O
PreemptionSwitch:
ff,
Off
PreemptionSwitch:
Off
cell loads (that is,
the load difference
between cells is
lower than the
related threshold).
It is recommended
that the
InterFreqMlbSwitch
be set to ON when
the load in the cell
is heavy (that is, the
average load in the
cell exceeds the
IntraFreqMlbSwitch:
Off,
balancing
InterFreqMlbSwitch:
IntraFreqMlbSwitch, threshold) and
Off,
InterFreqMlbSwitch, there is an
UtranMlbSwitch:Off,
UtranMlbSwitch, imbalance in the
GeranMlbSwitch:Off
GeranMlbSwitch, load between cells
, Engineering Design CellAlgoSwitch
CdmaMlbSwitch, (that is, the load
CdmaMlbSwitch:Off
IntraFreqIdleMlbSwi difference between
,
tch, cells exceeds the
IntraFreqIdleMlbSwi
UtranIdleMlbSwitch related threshold).
tch:Off,
It is recommended
UtranIdleMLBSwitc
that
h:Off
UtranMlbSwitch,
GeranMlbSwitch
and
CdmaMlbSwitch be
all set to OFF when
the cell load is light
in an early stage of
network
deployment (that is,
the average cell
load is lower than
70%).
It is recommended
PdschSpsPcSwitch: PdschSpsPcSwitch:
PdschSpsPcSwitch,
Off, Off
PhichInnerLoopPcS
PhichInnerLoopPcS PhichInnerLoopPcS Engineering Design CellAlgoSwitch
witch,
witch:Off, witch:Off
PdcchPcSwitch
PdcchPcSwitch:On PdcchPcSwitch:On
CloseLoopSpsSwitc CloseLoopSpsSwitc
CloseLoopSpsSwitc
h:Off, h:Off
h,
InnerLoopPuschSwi InnerLoopPuschSwi
InnerLoopPuschSwi
tch:On, tch:On
tch,
PhSinrTarUpdateS PhSinrTarUpdateS
PhSinrTarUpdateS
witch:Off, witch:Off
witch, Engineering Design CellAlgoSwitch
InnerLoopPucchSwi InnerLoopPucchSwi
InnerLoopPucchSwi
tch:On, tch:On
tch,
OiSinrTarUpdateSw OiSinrTarUpdateSw
OiSinrTarUpdateSw
itch:Off, itch:Off
itch,
PowerSavingSwitch PowerSavingSwitch
PowerSavingSwitch
:Off :Off
BfSwitch BfSwitch:Off BfSwitch:Off Engineering Design CellAlgoSwitch

FreqSelSwitch:Off, FreqSelSwitch:Off
FreqSelSwitch,
ServiceDiffSwitch:O ServiceDiffSwitch:O
ServiceDiffSwitch,
ff, ff
SpsSchSwitch, Engineering Design CellAlgoSwitch
SpsSchSwitch:Off, SpsSchSwitch:Off
MBSFNShutDownS
MBSFNShutDownS MBSFNShutDownS
witch
witch:Off witch:Off
SpsSchSwitch:Off, SpsSchSwitch:Off
SpsSchSwitch, SinrAdjustSwitch:O SinrAdjustSwitch:O
SinrAdjustSwitch, n, n
PreAllocationSwitch PreAllocationSwitch PreAllocationSwitch
Engineering Design CellAlgoSwitch
, UlVmimoSwitch, :On, :On
TtiBundlingSwitch, UlVmimoSwitch:Off, UlVmimoSwitch:Off
ImIcSwitch TtiBundlingSwitch: TtiBundlingSwitch:
Off, ImIcSwitch:Off Off
Default/Recommen
OFF, ON OFF(Off) OFF(Off) CellAlgoSwitch
ded Value
FreqPriorIFHOSwitc FreqPriorIFHOSwitc FreqPriorIFHOSwitc
h, h:Off, h:Off Default/Recommen
CellAlgoSwitch
FreqPriorIFBlindHO FreqPriorIFBlindHO FreqPriorIFBlindHO ded Value
Switch Switch:On Switch:On
Default/Recommen
MuBfSwitch MuBfSwitch:Off MuBfSwitch:Off CellAlgoSwitch
ded Value
Default/Recommen
OFF, ON OFF(Off) OFF(Off) CellAlgoSwitch
ded Value
ACBAR_SWITCH_
DYNAMIC,
ACBAR_SWITCH_ ACBAR_SWITCH_
ACBAR_SWITCH_
STATIC(static STATIC(static Engineering Design CellAlgoSwitch
STATIC,
configuration) configuration)
ACBAR_SWITCH_
DISABLE
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Engineering Design CellAlgoSwitch

DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Engineering Design CellAlgoSwitch
Radio Planning
0~17 None None CellDlIcic
(Internal planning)
not set to
INVALID(Invalid DL
band division
scheme), it is
recommended that
this parameter be
set to a different
value from those of
it is impossible for
INVALID(Invalid DL
MODE1, MODE2, neighboring cells to
band division Engineering Design CellDlIcic
MODE3, INVALID use mutually
scheme)
different band
modes, it is
recommended that
this parameter be
set to the same
value as that of a
neighboring cell
that has the
weakest
interference with
the current cell.
Radio Planning
0~17 None None CellDlpcPdcch
(Internal planning)
Default/Recommen
-15~15, step:0.1 -30 -30 CellDlpcPdcch
ded Value
Radio Planning
0~17 None None CellDlpcPdsch
(Internal planning)
PA_NEG6,
PA_NEG4DOT77,
PA_NEG3, Default/Recommen
PA_NEG6(-6dB) PA_NEG6(-6dB) CellDlpcPdsch
PA_NEG1DOT77, ded Value
PA_0, PA_1, PA_2,
PA_3
PA_NEG6,
PA_NEG4DOT77,
PA_NEG3, PA_NEG1DOT77(- PA_NEG1DOT77(- Default/Recommen
CellDlpcPdsch
PA_NEG1DOT77, 1.77dB) 1.77dB) ded Value
PA_0, PA_1, PA_2,
PA_3
Radio Planning
0~17 None None CellDlpcPhich
(Internal planning)
Default/Recommen
-15~15, step:0.1 0 0 CellDlpcPhich
ded Value
Radio Planning
0~17 None None CellDlschAlgo
(Internal planning)
DLSCH_PRI_TYPE
_EPF,
DLSCH_PRI_TYPE
_PF, DLSCH_PRI_TYPE DLSCH_PRI_TYPE
Engineering Design CellDlschAlgo
DLSCH_PRI_TYPE _EPF(EPF) _EPF(EPF)
_MAX_CI,
DLSCH_PRI_TYPE
_RR
0~100 0 0 Engineering Design CellDlschAlgo
0~1, step:0.01 1 1 Engineering Design CellDlschAlgo
0~1, step:0.01 10 10 Engineering Design CellDlschAlgo

SW_MAX_SM_RA
NK_1,
None Engineering Design CellDlschAlgo
NK_2, NK_2(Rank2)
SW_MAX_SM_RA
NK_4
Radio Planning
0~17 None None CellMLB
(Internal planning)
1~100 60 60 Engineering Design CellMLB


LOAD_EXCHANGE
_PERIOD_1S,
LOAD_EXCHANGE
_PERIOD_2S, LOAD_EXCHANGE LOAD_EXCHANGE Default/Recommen
CellMLB
LOAD_EXCHANGE _PERIOD_5S(5s) _PERIOD_5S(5s) ded Value
_PERIOD_5S,
LOAD_EXCHANGE
_PERIOD_10S
Default/Recommen
0~50 8 8 CellMLB
ded Value
Default/Recommen
1~50 15 15 CellMLB
ded Value
Radio Planning
0~17 None None CellPdcchAlgo
(Internal planning)
CONGREG_LV4,
CONGREG_LV4 CONGREG_LV4 Engineering Design CellPdcchAlgo
CONGREG_LV8
OFF, ON ON(On) ON(On) Engineering Design CellPdcchAlgo

If the switch for
dynamic adjustment
to the number of
OFDM symbols
occupied by the
PDCCH is turned
on, set this
parameter to 1. If
1~4 1 Engineering Design CellPdcchAlgo
the switch for
dynamic adjustment
to the number of
OFDM symbols
occupied by the
PDCCH is turned
off, set this
parameter to 3.
0~100 0 0 Engineering Design CellPdcchAlgo

In non-ultra-high-
speed scenarios
where the eNodeB
operates in FDD
mode, the
OFF, ON ON(On) Engineering Design CellPdcchAlgo
recommended
value is ON. In
other scenarios, the
recommended
value is OFF.
CCE usage within
each TTI. If the
value of this
parameter is
relatively small, the
PDCCH has
insufficient CCE
resources, which
will affect the
access success
rate of cell edge
UEs (CEUs),
handover success
rate, CCE
assignment
success rate for DL
scheduling, and
especially that for
UL scheduling.
1~100 100 Engineering Design CellPdcchAlgo
Therefore, at least
24 available CCEs
are required within
each TTI.
If multi-user MIMO
(MU-MIMO) and
multi-user
beamforming
(MUBF) are
enabled, you are
advised not to apply
restrictions on the
CCE usage within
each TTI. The
purpose is to
ensure successful
CCE assignment for
paired UEs and
maintain the MU-
OFF, ON ON(On) ON(On) Engineering Design CellPdcchAlgo
Radio Planning
0~17 None None CellPucchAlgo
(Internal planning)
bandwidths of 5
MHz and 10 MHz,
and 20 for
bandwidths of 15
MHz and 20 MHz.
If a competition test
on the access delay
or handover delay
is to be conducted
with UL
preallocation
disabled, set this
parameter to a
value greater than
1.
It is recommended
that the default
value of the
Default/Recommen
0~50 10 parameter be CellPucchAlgo
ded Value
retained. If
adjustments are
mandatory, avoid
setting this
parameter to an
excessively large
value as it may lead
to incorrect
decisions on the
load status of SRI
resources.
A value smaller
than or equal to 20
is recommended if
the cell bandwidth
is below 10 MHz. A
value smaller than
or equal to 40 is
Radio Planning CellNoAccessAlmP

0~17 None None
(Internal planning) ara
Default/Recommen CellNoAccessAlmP
00:00:00~23:59:59 00:00:00 00:00:00
ded Value ara
00:00:00~23:59:59 00:00:00 00:00:00
ded Value ara
0~72 0 0
ded Value ara
Radio Planning
0~17 None None CellUlIcic
(Internal planning)
not set to
INVALID(Invalid UL
band division
scheme), it is
recommended that
this parameter be
set to a different
value from those of
it is impossible for
INVALID(Invalid UL
MODE1, MODE2, neighboring cells to
band division Engineering Design CellUlIcic
MODE3, INVALID use mutually
scheme)
different band
modes, it is
recommended that
this parameter be
set to the same
value as that of a
neighboring cell
that has the
weakest
interference with
the current cell.
Radio Planning
0~17 None None CellSimuLoad
(Internal planning)
Default/Recommen
0~9 4 4 CellSimuLoad
ded Value
TM1, TM2, TM7, Default/Recommen

TM2(TM2) TM2(TM2) CellSimuLoad
TM8 ded Value
0~100 None None N/A CellSimuLoad
0~100, step:0.01 None None N/A CellSimuLoad
0~100, step:0.01 None None N/A CellSimuLoad
Radio Planning
0~17 None None BcchCfg
(Internal planning)
MOD_PERIOD_CO
EFF_N2,
MOD_PERIOD_CO
EFF_N4, MOD_PERIOD_CO MOD_PERIOD_CO Default/Recommen
BcchCfg
MOD_PERIOD_CO EFF_N2(2) EFF_N2(2) ded Value
EFF_N8,
MOD_PERIOD_CO
EFF_N16
Radio Planning
0~17 None None CellChPwrCfg
(Internal planning)
The recommended
-15.875~15.875, Default/Recommen
-600 value is -600 for all CellChPwrCfg
step:0.005 ded Value
FDD cells.
-600 in normal
-600 scenarios and peak CellChPwrCfg
rate tests.
In common
scenarios, the
recommended
value is -600 for the
cell bandwidth of
-15.875~15.875, 1.4, 3, or 5 MHz, Default/Recommen
0 CellChPwrCfg
step:0.005 and 0 for the cell ded Value
bandwidth of 10,
15, or 20 MHz. In
peak rate tests, the
recommended
value is -600.
-600 in normal
scenarios and peak
-15.875~15.875, rate tests, or 0 in Default/Recommen
-600 CellChPwrCfg
step:0.005 the tests on the ded Value
maximum cell
radius.
0 0 CellChPwrCfg
0 0 CellChPwrCfg
0 0 CellChPwrCfg
Radio Planning
0~17 None None PDSCHCfg
(Internal planning)
Default/Recommen
-60~50, step:0.1 182 None PDSCHCfg
ded Value
Single-antenna: 0; Default/Recommen
0~3 1 PDSCHCfg
double-antenna: 1 ded Value
Radio Planning
0~17 None None RACHCfg
(Internal planning)
DB0_PWR_RAMPI
NG_STEP,
DB2_PWR_RAMPI
NG_STEP, DB2_PWR_RAMPI DB2_PWR_RAMPI Default/Recommen
RACHCfg
DB4_PWR_RAMPI NG_STEP(2dB) NG_STEP(2dB) ded Value
NG_STEP,
DB6_PWR_RAMPI
NG_STEP
DBM_120,
DBM_118,
DBM_116,
DBM_114,
DBM_112,
DBM_110,
DBM_108, DBM_104(- DBM_104(- Default/Recommen
RACHCfg
DBM_106, 104dBm) 104dBm) ded Value
DBM_104,
DBM_102,
DBM_100,
DBM_98, DBM_96,
DBM_94, DBM_92,
DBM_90
B56_MSG_SIZE_G
ROUPA,
B144_MSG_SIZE_
GROUPA, B56_MSG_SIZE_G B56_MSG_SIZE_G Default/Recommen
RACHCfg
B208_MSG_SIZE_ ROUPA(56bits) ROUPA(56bits) ded Value
GROUPA,
B256_MSG_SIZE_
GROUPA
0~94 6 None Engineering Design RACHCfg

NOT_CFG, CFG RACHCfg
BTS3202E LTE:
If a cell is
configured with the
speed flag of
LOW_SPEED,
preamble format of
0, and bandwidth of
15 MHz or 20 MHz,
this parameter can
be set to 15 or a
value in the range
of 0 to 8.
0~63 3 Engineering Design RACHCfg
If a cell is
configured with the
speed flag of
LOW_SPEED,
preamble format of
0, and bandwidth of
smaller than or
equal to 10 MHz,
this parameter can
be set to 15 or a
value in the range
of 0 to 5.
Radio Planning
0~17 None None SRSCfg
(Internal planning)
SC0, SC1, SC2,
SC3, SC4, SC5, The value SC3(3) is
SC6, SC7, SC8, SC3(3) recommended for Engineering Design SRSCfg
SC9, SC10, SC11, FDD cells.
SC12, SC13, SC14
BOOLEAN_FALSE, BOOLEAN_TRUE( BOOLEAN_TRUE( Default/Recommen
SRSCfg
BOOLEAN_TRUE True) True) ded Value
It is recommended
that this parameter
be set to
BOOLEAN_TRUE(
True) if any of the
is met: (1) The
BOOLEAN_FALSE, BOOLEAN_TRUE( Default/Recommen
MimoAdaptiveSwitc SRSCfg
BOOLEAN_TRUE True) ded Value
h parameter is set
to OC_ADAPTIVE;
(2) UlVmimoSwitch
under the
UlSchSwitch
parameter is turned
on.
ACCESS_FIRST,
ACCESS_FIRST(A ACCESS_FIRST(A
EXPERIENCE_FIR Engineering Design SRSCfg
ccess First) ccess First)
ST
BW0, BW1, BW2,

BW3, BW4, BW5, None None N/A SRSCfg
BW6, BW7
Radio Planning
0~17 None None PHICHCfg
(Internal planning)
NORMAL, Default/Recommen
NORMAL NORMAL PHICHCfg
EXTENDED ded Value
ONE_SIXTH, HALF, Default/Recommen

ONE ONE PHICHCfg
ONE, TWO ded Value
Radio Planning
0~17 None None PCCHCfg
(Internal planning)
rf32, rf64, rf128, rf128(128 radio rf128(128 radio Default/Recommen
PCCHCfg
rf256 frames) frames) ded Value
FOURT, TWOT,
ONET, HALFT,
QUARTERT,
ONE_EIGHTT, Default/Recommen
ONET ONET PCCHCfg
ONE_SIXTEENTHT ded Value
,
ONE_THIRTY_SEC
ONDT
Radio Planning
0~17 None None PUSCHCfg
(Internal planning)
are set to
HOPPING_TYPE2
and
INTER_SUB_FRA
ME, respectively,
the recommended
value of this
parameter is 4.
If UlHoppingType
and HoppingMode
are set to
HOPPING_TYPE2
and
INTRA_AND_INTE
R_SUB_FRAME,
respectively, the
recommended
value of this
parameter is 1. Default/Recommen
1~4 4 PUSCHCfg
If UlHoppingType ded Value
and HoppingMode
are set to
HOPPING_TYPE2_
RANDOM and
INTER_SUB_FRA
ME, respectively,
the recommended
value of this
parameter is 4.
If UlHoppingType
and HoppingMode
are set to
HOPPING_TYPE2_
RANDOM and
INTRA_AND_INTE
R_SUB_FRAME,
respectively, the
recommended
INTER_SUB_FRA
ME, INTER_SUB_FRA INTER_SUB_FRA Default/Recommen
PUSCHCfg
INTRA_AND_INTE ME(Inter) ME(Inter) ded Value
R_SUB_FRAME
In FDD cells with
the normal CP
length, if DeltaShift
is set to
DS1_DELTA_SHIFT
, the recommended
values of this
parameter are 7,
10, 11, and 11,
corresponding to
cell bandwidths in
ascending order; if
DeltaShift is set to
DS2_DELTA_SHIFT
, the recommended Default/Recommen
0~98 22 PUSCHCfg
values of this ded Value
parameter are 8,
12, 13, and 14,
corresponding to
cell bandwidths in
ascending order; if
DeltaShift is set to
DS3_DELTA_SHIFT
, the recommended
values of this
parameter are 9,
16, 17, and 19,
corresponding to
cell bandwidths in
ascending order.
Engineering Design PUSCHCfg
0~29 0 0 Engineering Design PUSCHCfg
Default/Recommen
0~7 0 0 PUSCHCfg
ded Value
BOOLEAN_FALSE, BOOLEAN_TRUE( BOOLEAN_TRUE(
BOOLEAN_TRUE True) True)
Radio Planning
0~17 None None PUCCHCfg
(Internal planning)
Set this parameter

DS1_DELTA_SHIFT to
, DS2_DELTA_SHIF
DS2_DELTA_SHIFT DS1_DELTA_SHIF T for a cell Default/Recommen
PUCCHCfg
, T(ds1) configured with the ded Value
DS3_DELTA_SHIF BTS3202E LTE and
T the normal cyclic
prefix (CP).
0~100 6 6 Engineering Design PUCCHCfg

0~20 1 1 Engineering Design PUCCHCfg
Radio Planning Cdma2000External

6~32 characters None None
(Internal planning) CellPlmn
000~999 None None

00~99,000~999 None None
Radio Planning Cdma2000HrpdNce

0~17 None None
(Internal planning) ll
Radio Planning Cdma2000HrpdNce
(Internal planning) ll
PERMIT_HO_ENU
M, PERMIT_HO_ENU PERMIT_HO_ENU Radio Planning Cdma2000HrpdNce
FORBID_HO_ENU M(Permit Ho) M(Permit Ho) (Internal planning) ll
M
PERMIT_RMV_EN
PERMIT_RMV_EN PERMIT_RMV_EN
UM, Radio Planning Cdma2000HrpdNce
UM(Permit ANR UM(Permit ANR
FORBID_RMV_EN (Internal planning) ll
Remove) Remove)
UM
Cdma2000HrpdNce
ll
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( Cdma2000HrpdNce

Engineering Design
BOOLEAN_TRUE False) False) ll
Cdma2000HrpdNce
ll
Cdma2000HrpdNce
ll
Radio Planning
0~17 None None Cdma2000Nfreq
(Internal planning)
bc0, bc1, bc2, bc3,

bc4, bc5, bc6, bc7,
bc8, bc9, bc10, Radio Planning
None None Cdma2000Nfreq
bc11, bc12, bc13, (Internal planning)
bc14, bc15, bc16,
bc17
Radio Planning
0~2047 None None Cdma2000Nfreq
(Internal planning)
-15~15 0 0 Engineering Design Cdma2000Nfreq
NOT_CFG, CFG Engineering Design Cdma2000Nfreq
0~15 0 None Engineering Design Cdma2000Nfreq

Radio Planning EutranExternalCell
000~999 None None
(Internal planning) Plmn

00~99,000~999 None None

0~1048575 None None
0~255 None None

000~999 None None
00~99,000~999 None None
Radio Planning GeranExternalCellP

0~65535 None None
(Internal planning) lmn

1~65533,65535 None None

000~999 None None
00~99,000~999 None None

000~999 None None

00~99,000~999 None None
Radio Planning UtranExternalCellPl
0~268435455 None None
(Internal planning) mn

000~999 None None

00~99,000~999 None None
000~999 None None

00~99,000~999 None None
(Internal planning) Cell
bc0, bc1, bc2, bc3,

bc4, bc5, bc6, bc7,
bc8, bc9, bc10, Radio Planning Cdma2000External
None None
bc11, bc12, bc13, (Internal planning) Cell
bc14, bc15, bc16,
bc17

0~2047 None None
0~511 None None
CDMA2000_HRPD, CDMA2000_HRPD( CDMA2000_HRPD( Radio Planning Cdma2000External

CDMA2000_1XRTT CDMA2000_HRPD) CDMA2000_HRPD) (Internal planning) Cell

000~999 None None

00~99,000~999 None None
Cdma2000External
Cell
Radio Planning Cdma20001XRTTN

0~17 None None
(Internal planning) cell
Radio Planning Cdma20001XRTTN
(Internal planning) cell
PERMIT_HO_ENU
M, PERMIT_HO_ENU PERMIT_HO_ENU Radio Planning Cdma20001XRTTN
FORBID_HO_ENU M(Permit Ho) M(Permit Ho) (Internal planning) cell
M
PERMIT_RMV_EN
UM, Radio Planning Cdma20001XRTTN
FORBID_RMV_EN (Internal planning) cell
Remove) Remove)
UM
Cdma20001XRTTN
cell
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( Cdma20001XRTTN

Engineering Design
BOOLEAN_TRUE False) False) cell
Cdma20001XRTTN
cell
Cdma20001XRTTN
cell
Radio Planning Cdma2000BandCla

0~17 None None
(Internal planning) ss
bc0, bc1, bc2, bc3,

bc4, bc5, bc6, bc7,
bc8, bc9, bc10, Radio Planning Cdma2000BandCla
None None
bc11, bc12, bc13, (Internal planning) ss
bc14, bc15, bc16,
bc17
0~7 1 1

0~63 22 22
0~63 22 22
Radio Planning
000~999 None None GeranExternalCell
(Internal planning)
Radio Planning
00~99,000~999 None None GeranExternalCell
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
1~65533,65535 None None GeranExternalCell
(Internal planning)

NOT_CFG, CFG GeranExternalCell
Radio Planning
0~255 0 None GeranExternalCell
(Internal planning)
GSM_dcs1800, Radio Planning

None None GeranExternalCell
GSM_pcs1900 (Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
DTM_AVAILABLE,
DTM_NOT_AVAILA DTM_NOT_AVAILA Radio Planning
DTM_NOT_AVAILA GeranExternalCell
BLE BLE (Internal planning)
BLE
0~99 characters NULL None Engineering Design GeranExternalCell
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( Radio Planning

GeranExternalCell
BOOLEAN_TRUE False) False) (Internal planning)
Radio Planning
0~17 None None GeranNcell
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
00~99,000~999 None None GeranNcell
(Internal planning)
Radio Planning
1~65533,65535 None None GeranNcell
(Internal planning)
Radio Planning
(Internal planning)
PERMIT_RMV_EN
UM,
UM(Permit ANR UM(Permit ANR Engineering Design GeranNcell
FORBID_RMV_EN
Remove) Remove)
UM
PERMIT_HO_ENU
M, PERMIT_HO_ENU PERMIT_HO_ENU
Engineering Design GeranNcell
FORBID_HO_ENU M(Permit Ho) M(Permit Ho)
M
0~32 0 0 Engineering Design GeranNcell

GeranNcell
0~99 characters NULL None Engineering Design GeranNcell

0~99 characters NULL None Engineering Design GeranNcell
0~1048575 None None N/A GeranNcell
0~32 characters None None N/A GeranNcell
0~32 characters None None N/A GeranNcell
Radio Planning
0~17 None None GeranNfreqGroup
(Internal planning)
Radio Planning
(Internal planning)
GSM, GPRS, Radio Planning

None None GeranNfreqGroup
EDGE (Internal planning)
Radio Planning
(Internal planning)
GSM_dcs1800, Radio Planning
None None GeranNfreqGroup
GSM_pcs1900 (Internal planning)
NOT_CFG, CFG Engineering Design GeranNfreqGroup
0~7 1 1 Engineering Design GeranNfreqGroup

NOT_CFG, CFG GeranNfreqGroup
0~39 0 None Engineering Design GeranNfreqGroup
Default/Recommen
-115~-25, step:2 0 0 GeranNfreqGroup
ded Value
Default/Recommen
0~62, step:2 7 7 GeranNfreqGroup
ded Value
Default/Recommen
0~62, step:2 7 7 GeranNfreqGroup
ded Value
Default/Recommen
-15~15 0 0 GeranNfreqGroup
ded Value
Default/Recommen
0~255 255 255 GeranNfreqGroup
ded Value
Radio Planning GeranNfreqGroupA

0~17 None None
(Internal planning) rfcn
0~31 None None

0~1023 None None
0~17 None None Engineering Design IntraFreqBlkCell
0~503 None None Engineering Design IntraFreqBlkCell
0~99 characters NULL None Engineering Design IntraFreqBlkCell

n1, n4, n8, n12,
n16, n24, n32, n48,
n64, n84, n96, n1(n1) None Engineering Design IntraFreqBlkCell
n128, n168, n252,
n504
Radio Planning EutranIntraFreqNC

0~17 None None
(Internal planning) ell

000~999 None None

00~99,000~999 None None
0~1048575 None None

0~255 None None
dB-24, dB-22, dB-
20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
Default/Recommen EutranIntraFreqNC
dB-1, dB0, dB1, dB0(0dB) dB0(0dB)
ded Value ell
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
dB-24, dB-22, dB-

20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
Default/Recommen EutranIntraFreqNC
ded Value ell
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
PERMIT_HO_ENU
M, PERMIT_HO_ENU PERMIT_HO_ENU Radio Planning EutranIntraFreqNC
FORBID_HO_ENU M(Permit Ho) M(Permit Ho) (Internal planning) ell
M
PERMIT_RMV_EN
UM, Radio Planning EutranIntraFreqNC
FORBID_RMV_EN (Internal planning) ell
Remove) Remove)
UM
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( Default/Recommen EutranIntraFreqNC

BOOLEAN_TRUE False) False) ded Value ell
EutranIntraFreqNC
ell
EutranIntraFreqNC
ell
Radio Planning
0~17 None None EutranInterNFreq
(Internal planning)
None None EutranInterNFreq

NOT_CFG, CFG EutranInterNFreq
18000 None EutranInterNFreq

Radio Planning
0~7 1 1 EutranInterNFreq
(Internal planning)
Default/Recommen
ded Value
0DOT25_ENUM,
0DOT5_ENUM, 0DOT25_ENUM(0.
None Engineering Design EutranInterNFreq
0DOT75_ENUM, 25)
1DOT0_ENUM
0DOT25_ENUM,
0DOT5_ENUM, 0DOT25_ENUM(0.
None Engineering Design EutranInterNFreq
0DOT75_ENUM, 25)
1DOT0_ENUM
MBW6, MBW15,
MBW25, MBW50, None None Engineering Design EutranInterNFreq
MBW75, MBW100
dB-24, dB-22, dB-

20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
Default/Recommen
dB-1, dB0, dB1, dB1(1dB) dB1(1dB) EutranInterNFreq
ded Value
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
Default/Recommen
0~62, step:2 11 11 EutranInterNFreq
ded Value
Default/Recommen
0~62, step:2 11 11 EutranInterNFreq
ded Value
Default/Recommen
-140~-44, step:2 -64 -64 EutranInterNFreq
ded Value

Default/Recommen
-30~33 23 23 EutranInterNFreq
ded Value
BitString00,
BitString01, Default/Recommen
BitString01(01) BitString01(01) EutranInterNFreq
BitString10, ded Value
BitString11
EutranInterNFreq
If the neighboring
E-UTRAN
frequency and the
serving frequency
are in the same
frequency band, the
value EventA3 is
EventA3, EventA4, recommended.
EventA4(EventA4) Engineering Design EutranInterNFreq
EventA5 If the neighboring
E-UTRAN
frequency and the
serving frequency
are in different
frequency bands,
the value EventA4
is recommended.
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
NOT_CFG, CFG Engineering Design EutranInterNFreq
Radio Planning
-34~-3 -18 -18 EutranInterNFreq
(Internal planning)
0~17 None None Engineering Design InterFreqBlkCell

0~45589,64436~65
None None Engineering Design InterFreqBlkCell
535
0~503 None None Engineering Design InterFreqBlkCell
0~99 characters NULL None Engineering Design InterFreqBlkCell

n1, n4, n8, n12,
n16, n24, n32, n48,
n64, n84, n96, n1(n1) None Engineering Design InterFreqBlkCell
n128, n168, n252,
n504
Radio Planning EutranInterFreqNC

0~17 None None

000~999 None None

00~99,000~999 None None
0~1048575 None None

0~255 None None
dB-24, dB-22, dB-
20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
Default/Recommen EutranInterFreqNC
ded Value ell
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
dB-24, dB-22, dB-

20, dB-18, dB-16,
dB-14, dB-12, dB-
10, dB-8, dB-6, dB-
5, dB-4, dB-3, dB-2,
Default/Recommen EutranInterFreqNC
ded Value ell
dB2, dB3, dB4,
dB5, dB6, dB8,
dB10, dB12, dB14,
dB16, dB18, dB20,
dB22, dB24
PERMIT_HO_ENU
M, PERMIT_HO_ENU PERMIT_HO_ENU Radio Planning EutranInterFreqNC
FORBID_HO_ENU M(Permit Ho) M(Permit Ho) (Internal planning) ell
M
PERMIT_RMV_EN
UM, Radio Planning EutranInterFreqNC
FORBID_RMV_EN (Internal planning) ell
Remove) Remove)
UM

0~32 0 0
BOOLEAN_FALSE, BOOLEAN_FALSE( BOOLEAN_FALSE( Default/Recommen EutranInterFreqNC
BOOLEAN_TRUE False) False) ded Value ell
EutranInterFreqNC
ell
EutranInterFreqNC
ell
Radio Planning
000~999 None None EutranExternalCell
(Internal planning)
Radio Planning
00~99,000~999 None None EutranExternalCell
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)

None None EutranExternalCell
NOT_CFG, CFG EutranExternalCell

18000 None EutranExternalCell
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
0~99 characters NULL None Engineering Design EutranExternalCell
Radio Planning
0~17 None None GeranRanShare
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
00~99,000~999 None None GeranRanShare
(Internal planning)
NOT_CFG, CFG GeranRanShare
Radio Planning
0~7 0 0 GeranRanShare
(Internal planning)
Radio Planning
0~17 None None UtranNCell
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
00~99,000~999 None None UtranNCell
(Internal planning)
Radio Planning
(Internal planning)
PERMIT_HO_ENU
M, PERMIT_HO_ENU PERMIT_HO_ENU Radio Planning
UtranNCell
FORBID_HO_ENU M(Permit Ho) M(Permit Ho) (Internal planning)
M
PERMIT_RMV_EN
UM, Radio Planning
UM(Permit ANR UM(Permit ANR UtranNCell
FORBID_RMV_EN (Internal planning)
Remove) Remove)
UM
Radio Planning
0~32 0 0 UtranNCell
(Internal planning)

UtranNCell
0~99 characters NULL None Engineering Design UtranNCell
0~99 characters NULL None Engineering Design UtranNCell
0~1048575 None None N/A UtranNCell

0~4095 None None N/A UtranNCell
0~32 characters None None N/A UtranNCell
0~32 characters None None N/A UtranNCell
Radio Planning
0~17 None None UtranRanShare
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
00~99,000~999 None None UtranRanShare
(Internal planning)

NOT_CFG, CFG UtranRanShare
Radio Planning
0~7 0 0 UtranRanShare
(Internal planning)
Radio Planning
0~17 None None UtranNFreq
(Internal planning)
Radio Planning
0~16383 None None UtranNFreq
(Internal planning)
R99, HSDPA,
HSUPA HSUPA Engineering Design UtranNFreq
HSUPA, HSPA
UTRAN_FDD, Radio Planning

UTRAN_FDD UTRAN_FDD UtranNFreq
UTRAN_TDD (Internal planning)
NOT_CFG, CFG UtranNFreq
Radio Planning
0~16383 0 None UtranNFreq
(Internal planning)

NOT_CFG, CFG UtranNFreq
Radio Planning
0~7 1 1 UtranNFreq
(Internal planning)
Default/Recommen
-50~33 33 33 UtranNFreq
ded Value
Default/Recommen
-15~15 0 0 UtranNFreq
ded Value
Default/Recommen
-24~0 -22 -22 UtranNFreq
ded Value
Default/Recommen
-119~-25, step:2 -58 -58 UtranNFreq
ded Value
Default/Recommen
0~62, step:2 6 6 UtranNFreq
ded Value
Default/Recommen
0~62, step:2 6 6 UtranNFreq
ded Value
Default/Recommen
0~31 0 0 UtranNFreq
ded Value
Default/Recommen
0~31 0 0 UtranNFreq
ded Value
LOW_PRIORITY, HIGH_PRIORITY(H HIGH_PRIORITY(H
Engineering Design UtranNFreq
HIGH_PRIORITY igh Priority) igh Priority)
LOW_PRIORITY, HIGH_PRIORITY(H HIGH_PRIORITY(H
Engineering Design UtranNFreq
HIGH_PRIORITY igh Priority) igh Priority)
Radio Planning
000~999 None None UtranExternalCell
(Internal planning)
Radio Planning
00~99,000~999 None None UtranExternalCell
(Internal planning)
Radio Planning
(Internal planning)
UTRAN_FDD,
UTRAN_FDD UTRAN_FDD Engineering Design UtranExternalCell
UTRAN_TDD
Radio Planning
(Internal planning)
NOT_CFG, CFG UtranExternalCell
Radio Planning
0~16383 0 None UtranExternalCell
(Internal planning)
Radio Planning
(Internal planning)

NOT_CFG, CFG UtranExternalCell
Radio Planning
0~255 0 None UtranExternalCell
(Internal planning)
Radio Planning
(Internal planning)
Radio Planning
1~65533,65535 None None UtranExternalCell
(Internal planning)
0~99 characters NULL None Engineering Design UtranExternalCell

UtranExternalCell
0~100 80 80 Engineering Design ANR

r1, r2, r4, r8, r16,

r64(64) r64(64) Engineering Design ANR
r32, r64, Infinity
120ms, 240ms,
480ms, 640ms,
1024ms, 2048ms,
5120ms 5120ms Engineering Design ANR
5120ms, 10240ms,
1min, 6min, 12min,
30min, 60min
-130~-70 -102 -102 Engineering Design ANR


FREE,
FREE(FREE) FREE(FREE) Engineering Design ANR
CONTROLLED

OFF, ON OFF(Off) OFF(Off) Engineering Design ANR
Default/Recommen
00:00:00~23:59:59 14:00:00 14:00:00 ANR
ded Value
Default/Recommen
00:00:00~23:59:59 15:00:00 15:00:00 ANR
ded Value
-31.5~0, step:0.5 -30 -30 Engineering Design ANR

-31.5~0, step:0.5 -16 -16 Engineering Design ANR
BOOLEAN_FALSE, BOOLEAN_FALSE(
None Engineering Design CellIdPrdUpt
BOOLEAN_TRUE False)
2000-01-
01T00:00:00.000- 2000-01-
00:00~2099-12- 01T00:00:00.000- None Engineering Design CellIdPrdUpt
31T23:59:59.000- 00:00
00:00
1~365 1 None Engineering Design CellIdPrdUpt

Radio Planning
0~1048575 None None eNBRsvdPara
(Internal planning)
ameter0_bit7:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
0,
ameter0_bit8:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
1,
ameter0_bit9:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
2,
ameter0_bit10:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
3,
ameter0_bit11:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
4,
ameter0_bit12:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
5,
ameter0_bit13:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
6,
ameter0_bit14:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
7,
ameter0_bit15:Off,
RsvdSwPara0_bit1
ReservedSwitchPar
8,
RsvdSwPara0_bit1 None eNBRsvdPara
9,
ameter0_bit17:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
0,
ameter0_bit18:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
1,
ameter0_bit19:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
2,
ameter0_bit20:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
3,
ameter0_bit21:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
4,
ameter0_bit22:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
5,
ameter0_bit23:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
6,
ameter0_bit24:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
7,
ameter0_bit25:Off,
RsvdSwPara0_bit2
ReservedSwitchPar
ameter1_bit7:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
0,
ameter1_bit8:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
1,
ameter1_bit9:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
2,
ameter1_bit10:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
3,
ameter1_bit11:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
4,
ameter1_bit12:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
5,
ameter1_bit13:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
6,
ameter1_bit14:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
7,
ameter1_bit15:Off,
RsvdSwPara1_bit1
ReservedSwitchPar
8,
RsvdSwPara1_bit1 None eNBRsvdPara
9,
ameter1_bit17:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
0,
ameter1_bit18:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
1,
ameter1_bit19:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
2,
ameter1_bit20:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
3,
ameter1_bit21:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
4,
ameter1_bit22:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
5,
ameter1_bit23:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
6,
ameter1_bit24:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
7,
ameter1_bit25:Off,
RsvdSwPara1_bit2
ReservedSwitchPar
RsvdSwPara2_bit1
0,
RsvdSwPara2_bit1
1,
RsvdSwPara2_bit1
2,
RsvdSwPara2_bit1
3,
RsvdSwPara2_bit1
4,
RsvdSwPara2_bit1
5,
RsvdSwPara2_bit1
6,
RsvdSwPara2_bit1
7,
RsvdSwPara2_bit1
8,
Default/Recommen
RsvdSwPara2_bit1 None None eNBRsvdPara
ded Value
9,
RsvdSwPara2_bit2
0,
RsvdSwPara2_bit2
1,
RsvdSwPara2_bit2
2,
RsvdSwPara2_bit2
3,
RsvdSwPara2_bit2
4,
RsvdSwPara2_bit2
5,
RsvdSwPara2_bit2
6,
RsvdSwPara2_bit2
7,
RsvdSwPara2_bit2
Default/Recommen
0~4294967295 0 None eNBRsvdPara
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
IntraFreqCoverHoS IntraFreqCoverHoS
witch:On, witch:On
IntraFreqCoverHoS
InterFreqCoverHoS InterFreqCoverHoS
witch,
witch:On, witch:On
InterFreqCoverHoS
UtranCsfbSwitch:Of UtranCsfbSwitch:Of
witch,
f, f
UtranCsfbSwitch,
GeranCsfbSwitch:O GeranCsfbSwitch:O
GeranCsfbSwitch,
ff, ff
Cdma1xRttCsfbSwit
Cdma20001xRttCsf Cdma1xRttCsfbSwit
ch,
bSwitch:Off, ch:Off
UtranServiceHoSwit
UtranServiceHoSwit UtranServiceHoSwit
ch,
ch:Off, ch:Off
GeranServiceHoSw
GeranServiceHoSw GeranServiceHoSw
itch,
itch:Off, itch:Off
CdmaHrpdServiceH
Cdma2000HrpdSer Cdma2000HrpdSer
oSwitch, Engineering Design ENodeBAlgoSwitch
viceHoSwitch:Off, viceHoSwitch:Off
Cdma1xRttService
Cdma20001xRttSer Cdma20001xRttSer
HoSwitch,
viceHoSwitch:Off, viceHoSwitch:Off
UlQualityInterRATH
UlQualityInterRATH UlQualityInterRATH
oSwitch,
oSwitch:Off, oSwitch:Off
InterPlmnHoSwitch,
InterPlmnHoSwitch: InterPlmnHoSwitch:
UtranFlashCsfbSwit
Off, Off
ch,
UtranFlashCsfbSwit UtranFlashCsfbSwit
GeranFlashCsfbSwi
ch:Off, ch:Off
tch,
GeranFlashCsfbSwi GeranFlashCsfbSwi
ServiceBasedInterF
tch:Off, tch:Off
reqHoSwitch,
ServiceBasedInterF ServiceBasedInterF
UlQualityInterFreqH
reqHoSwitch:Off, reqHoSwitch:Off
oSwitch
UlQualityInterFreqH UlQualityInterFreqH
oSwitch:Off oSwitch:Off
EutranVoipCapSwit EutranVoipCapSwit
ch:On, ch:On
UtranVoipCapSwitc UtranVoipCapSwitc
EutranVoipCapSwit h:Off, h:Off
ch, GeranVoipCapSwitc GeranVoipCapSwitc
UtranVoipCapSwitc h:Off, h:Off
h, Cdma1xRttVoipCap Cdma1xRttVoipCap
GeranVoipCapSwitc Switch:Off, Switch:Off
h, UtranPsHoSwitch:O UtranPsHoSwitch:O
Cdma1xRttVoipCap ff, ff
Switch, GeranPsHoSwitch: GeranPsHoSwitch:
UtranPsHoSwitch, Off, Off
GeranPsHoSwitch, CdmaHrpdNonOtpi CdmaHrpdNonOtpi
CdmaHrpdNonOtpi misedHoSwitch:Off, misedHoSwitch:Off
misedHoSwitch, CdmaHrpdOptimise CdmaHrpdOptimise
CdmaHrpdOptimise dHoSwitch:Off, dHoSwitch:Off
dHoSwitch, GeranNaccSwitch: GeranNaccSwitch:
GeranNaccSwitch, Off, Off Engineering Design ENodeBAlgoSwitch
GeranCcoSwitch, GeranCcoSwitch:Of GeranCcoSwitch:Of
UtranSrvccSwitch, f, f
GeranSrvccSwitch, UtranSrvccSwitch:O UtranSrvccSwitch:O
Cdma1xRttSrvccSw ff, ff
itch, GeranSrvccSwitch: GeranSrvccSwitch:
UtranRedirectSwitc Off, Off
h, Cdma1xRttSrvccSw Cdma1xRttSrvccSw
GeranRedirectSwitc itch:Off, itch:Off
h, UtranRedirectSwitc UtranRedirectSwitc
CdmaHrpdRedirect h:Off, h:Off
Switch, GeranRedirectSwitc GeranRedirectSwitc
Cdma1xRttRedirect h:Off, h:Off
Switch, CdmaHrpdRedirect CdmaHrpdRedirect
BlindHoSwitch Switch:Off, Switch:Off
Cdma1xRttRedirect Cdma1xRttRedirect
Switch:Off, Switch:Off
BlindHoSwitch:Off BlindHoSwitch:Off
DlIcicSwitch_OFF_
ENUM,
DlIcicDynamicSwitc
h_ON_ENUM, DlIcicSwitch_OFF_ DlIcicSwitch_OFF_
Engineering Design ENodeBAlgoSwitch
DlIcicStaticSwitch_ ENUM ENUM
ON_ENUM,
DlIcicReuse3Switch
_ON_ENUM
IntraRatEventAnrS IntraRatEventAnrS IntraRatEventAnrS
witch, witch:Off, witch: Off
IntraRatFastAnrSwit IntraRatFastAnrSwit IntraRatFastAnrSwit
ch, ch:Off, ch: Off
IntraRatAnrAutoDel IntraRatAnrAutoDel IntraRatAnrAutoDel
Switch, Switch:On, Switch: On
UtranEventAnrSwitc UtranEventAnrSwitc UtranEventAnrSwitc
h, h:Off, h: Off
GeranEventAnrSwit GeranEventAnrSwit GeranEventAnrSwit
ch, ch:Off, ch: Off
UtranFastAnrSwitch UtranFastAnrSwitch UtranFastAnrSwitch
, :Off, : Off
GeranFastAnrSwitc GeranFastAnrSwitc GeranFastAnrSwitc
h, h:Off, h: Off
CdmaFastAnrSwitc CdmaFastAnrSwitc CdmaFastAnrSwitc
h, h:Off, h: Off
UtranAutoNrtDelete UtranAutoNrtDelete UtranAutoNrtDelete
GeranAutoNrtDelet GeranAutoNrtDelet GeranAutoNrtDelet
eSwitch, eSwitch:On, eSwitch: On
CdmaAutoNrtDelete CdmaAutoNrtDelete CdmaAutoNrtDelete
ExtendIntraRatAnrS ExtendIntraRatAnrS ExtendIntraRatAnrS
witch witch:Off witch:Off
LoadBasedSwitch: LoadBasedSwitch:
LoadBasedSwitch,
Off, Off
GeranFlashRedirect
GeranFlashRedirect GeranFlashRedirect
Switch, Engineering Design ENodeBAlgoSwitch
Switch:Off, Switch:Off
UranFlashRedirect
UranFlashRedirect UranFlashRedirect
Switch
Switch:Off Switch:Off
IntraFreqMroAlgoS
IntraFreqMroAlgoS
witch:Off,
IntraFreqMroSwitch witch:Off
InterFreqMroAlgoS
, InterFreqMroAlgoS
witch:Off,
InterFreqMroSwitch witch:Off Engineering Design ENodeBAlgoSwitch
UtranMroSwitch:Off
, UtranMroSwitch, UtranMroSwitch:Off
,
GeranMroSwitch GeranMroSwitch:Of
GeranMroSwitch:Of
f
f
TpeAlgoSwitch TpeAlgoSwitch:Off TpeAlgoSwitch:Off Engineering Design ENodeBAlgoSwitch
Uplink Intra-eNB Uplink Intra-eNB

UlIcicIntraSwitch Engineering Design ENodeBAlgoSwitch
ICIC switch:Off ICIC switch:Off
OFF, STATIC,
OFF(Off) OFF(Off) Engineering Design ENodeBAlgoSwitch
DYNAMIC
Default/Recommen
OtdoaSwitch OTDOA switch:Off OTDOA switch:Off ENodeBAlgoSwitch
ded Value
UU flow control UU flow control
UlUuFlowCtrlSwitch Engineering Design ENodeBAlgoSwitch
switch:Off switch:Off
Default/Recommen
OFF, ON OFF(Off) OFF(Off) ENodeBAlgoSwitch
ded Value
SymbolShutdownS Symbol shutdown Symbol shutdown
witch switch:Off switch: Off
UTRAN_RIM_SWIT UTRAN RIM
UTRAN RIM
CH, Switch:Off
Switch:Off, GERAN Engineering Design ENodeBAlgoSwitch
GERAN_RIM_SWI GERAN RIM
RIM Switch:Off
TCH Switch:Off
NBSLTEPLMNRou NBSLTEPLMNRou NBSLTEPLMNRou
ndSwitch, ndSwitch:Off, ndSwitch:Off
NBSLTERANSharin NBSLTERANSharin NBSLTERANSharin
gSwitch gSwitch:Off gSwitch:Off
UtranFreqLayerMea UtranFreqLayerMea UtranFreqLayerMea
sSwitch, sSwitch:Off, sSwitch:Off
UtranFreqLayerBlin UtranFreqLayerBlin UtranFreqLayerBlin
dSwitch dSwitch:Off dSwitch:Off
Default/Recommen
1~65535 5 5 LICENSEALMTHD
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
1~100 25 25 Engineering Design LicRatio

SHARING,
SHARING(Sharing) SHARING(Sharing) Engineering Design LicRatio
DEDICATE




Default/Recommen
1~70000 1440 1440 MRO
ded Value
Default/Recommen
0~100 99 99 MRO
ded Value
Default/Recommen
0~10000 1000 1000 MRO
ded Value
Default/Recommen
1~60 1 1 MRO
ded Value
Default/Recommen
0~100 5 5 MRO
ded Value
Default/Recommen
0~100 60 60 MRO
ded Value
Default/Recommen
-140~-44 -116 -116 MRO
ded Value
Default/Recommen
-140~-44 -116 -116 MRO
ded Value
0~9 None None Engineering Design SimuLoad
Default/Recommen
0~100 50 50 SimuLoad
ded Value
Default/Recommen
0~100 50 50 SimuLoad
ded Value
Default/Recommen
0~50000 500 500 SimuLoad
ded Value
Default/Recommen
0~50000 5000 5000 SimuLoad
ded Value
Default/Recommen
OFF, ON OFF(Off) OFF(Off) SimuLoad
ded Value
OFF, ON OFF(Off) 0 Engineering Design TcpAckCtrlAlgo

0~4294967295 0 0 Engineering Design TcpAckCtrlAlgo
1~255 1 1 Engineering Design TcpAckCtrlAlgo
0~261120,275943~ Default/Recommen
0 0 TddFrameOffset
307200 ded Value
0~20 3 3 Engineering Design TpeAlgo

Transport
0~195 None None Planning(Internal NODETORSCGRP
planning)
Transport
SGW, X2eNodeB None None Planning(Internal NODETORSCGRP
planning)
Transport
NO, YES None None Planning(Internal NODETORSCGRP
planning)
This parameter
must be set to the
ID of an S-GW or
neighboring
eNodeB. If the peer
device is an S-GW,
set this parameter Transport
0~127 0 to a value in the Planning(Internal NODETORSCGRP
range of 0 to 127. If planning)
the peer device is a
neighboring
eNodeB, set this
parameter to a
value in the range
of 16 to 79.
Default/Recommen
0~7 0 0 NODETORSCGRP
ded Value
Default/Recommen
0~1 0 0 NODETORSCGRP
ded Value
Default/Recommen
0~7 None None NODETORSCGRP
ded Value
Transport
IP None None Planning(Internal NODETORSCGRP
planning)
Transport
0~15 None None Planning(Internal NODETORSCGRP
planning)
BASE_BOARD,
E1_COVERBOARD Transport
, BACK_BOARD, None None Planning(Internal NODETORSCGRP
ETH_COVERBOAR planning)
D
Transport
0~15 0 0 Planning(Internal NODETORSCGRP
planning)
Transport
PPP, MPGRP, ETH,
None None Planning(Internal NODETORSCGRP
ETHTRK, TUNNEL
planning)
Transport
1~15 characters None None Planning(Internal SonSecPara
planning)
Transport
1~99 None None Planning(Internal SonSecPara
planning)
Transport
planning)
Transport
X2, S1 X2(X2) None Planning(Internal SonSecPara
planning)
Transport
IKE_V1, IKE_V2 IKE_V2(IKE V2) IKE_V2(IKE V2) Planning(Internal SonSecPara
planning)
Transport
MAIN,
MAIN(Main Mode) MAIN(Main Mode) Planning(Internal SonSecPara
AGGRESSIVE
planning)
Transport
planning)
Transport
DISABLE, PERIODIC(Periodic
PERIODIC Planning(Internal SonSecPara
PERIODIC )
planning)
Default/Recommen
10~3600 10 None SonSecPara
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
DISABLE, Transport
PFS_GROUP1, DISABLE(Disable) DISABLE Planning(Internal SonSecPara
PFS_GROUP2 planning)
Transport
LOCAL(Local
GLOBAL, LOCAL None Planning(Internal SonSecPara
Configuration)
planning)
Default/Recommen
30~604800 3600 3600 SonSecPara
ded Value
0,1843200~429496 Default/Recommen
69120000 None SonSecPara
7295 ded Value
Transport
0~5 None None Planning(Internal SonSecPara
planning)
Transport
1~15 characters None None Planning(Internal MME6
planning)
Transport
Valid IP address None None Planning(Negotiatio MME6
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio MME6
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
0~15 characters NULL None Planning(Negotiatio MME6
n with the peer)
Transport
n with the peer)
This parameter is
Transport
not required if
Valid IP address 0:0:0:0:0:0:0:0 Planning(Negotiatio MME6
SCTP multi-homing
n with the peer)
is not supported.
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio MME6
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
1024~65535 None None Planning(Negotiatio MME6
n with the peer)
Transport
0~20 characters NULL None Planning(Internal MME6
planning)
Transport
0~5 0 None Planning(Negotiatio MME6
n with the peer)
Release_R8, Transport
Release_R8(Releas
Release_R9, None Planning(Negotiatio MME6
e 8)
Release_R10 n with the peer)
Transport
0~15 None None Planning(Internal MME
planning)
Transport
Valid IP address None None Planning(Negotiatio MME
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio MME
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
0~15 characters NULL None Planning(Negotiatio MME
n with the peer)
Transport
n with the peer)
This parameter is
Transport
required only if
Valid IP address 0.0.0.0 Planning(Negotiatio MME
SCTP multihoming
n with the peer)
is supported.
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio MME
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
1024~65535 None None Planning(Negotiatio MME
n with the peer)
Transport
0~20 characters NULL None Planning(Internal MME
planning)
Transport
0~5 0 None Planning(Negotiatio MME
n with the peer)
Release_R8(Releas
Release_R9, None Planning(Negotiatio MME
e 8)
Default/Recommen
0~7 0 0 S1ServIP
ded Value
Default/Recommen
0~1 0 0 S1ServIP
ded Value
Default/Recommen
0~7 None 7 S1ServIP
ded Value
Transport
1~15 characters None None Planning(Internal S1ServIP
planning)
Transport
Valid IP address None None Planning(Internal S1ServIP
planning)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Internal S1ServIP
manually
planning)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
Valid IP address 0.0.0.0 None Planning(Internal S1ServIP
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal S1ServIP
planning)
Transport
0~5 0 None Planning(Internal S1ServIP
planning)
Transport
1~15 characters None None Planning(Internal S1ServIP6
planning)
Default/Recommen
0~7 0 0 S1ServIP6
ded Value
Default/Recommen
0~1 0 0 S1ServIP6
ded Value
Default/Recommen
0~7 None 7 S1ServIP6
ded Value
Transport
Valid IP address None None Planning(Internal S1ServIP6
planning)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Internal S1ServIP6
manually
planning)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal S1ServIP6
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal S1ServIP6
planning)
Transport
0~5 0 None Planning(Internal S1ServIP6
planning)
Default/Recommen
0~7 0 0 S1SigIP
ded Value
Default/Recommen
0~1 0 0 S1SigIP
ded Value
Default/Recommen
0~7 None 7 S1SigIP
ded Value
Transport
1~15 characters None None Planning(Internal S1SigIP
planning)
Transport
Valid IP address None None Planning(Internal S1SigIP
planning)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Internal S1SigIP
manually
planning)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
Valid IP address 0.0.0.0 None Planning(Internal S1SigIP
planning)
The value 0.0.0.0 is
Transport
recommended if
Valid IP address 0.0.0.0 Planning(Internal S1SigIP
SCTP multihoming
planning)
is not supported.
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Internal S1SigIP
manually
planning)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
Valid IP address 0.0.0.0 None Planning(Internal S1SigIP
planning)
Transport
1024~65535 None None Planning(Internal S1SigIP
planning)
Default/Recommen
10~59999 1000 1000 S1SigIP
ded Value
Default/Recommen
11~60000 3000 3000 S1SigIP
ded Value
Default/Recommen
10~59999 1000 1000 S1SigIP
ded Value
Default/Recommen
1~99 12 12 S1SigIP
ded Value
Default/Recommen
1~99 25 25 S1SigIP
ded Value
Default/Recommen
1000~60000 5000 5000 S1SigIP
ded Value
Default/Recommen
2~254 10 10 S1SigIP
ded Value
Default/Recommen
1~253 5 5 S1SigIP
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) S1SigIP
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) S1SigIP
ded Value
Default/Recommen
ALDER32, CRC32 CRC32(CRC32) CRC32(CRC32) S1SigIP
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) S1SigIP
ded Value
Default/Recommen
1~254 10 10 S1SigIP
ded Value
Default/Recommen
10~500 200 200 S1SigIP
ded Value
Transport
0~5 0 None Planning(Internal S1SigIP
planning)
Transport
1~15 characters None None Planning(Internal S1SigIP6
planning)
Default/Recommen
0~7 0 0 S1SigIP6
ded Value
Default/Recommen
0~1 0 0 S1SigIP6
ded Value
Default/Recommen
0~7 None 7 S1SigIP6
ded Value
Transport
Valid IP address None None Planning(Internal S1SigIP6
planning)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Internal S1SigIP6
manually
planning)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal S1SigIP6
planning)
This parameter is
Transport
not required if
Valid IP address 0:0:0:0:0:0:0:0 Planning(Internal S1SigIP6
SCTP multi-homing
planning)
is not supported.
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Internal S1SigIP6
manually
planning)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal S1SigIP6
planning)
Transport
1024~65535 None None Planning(Internal S1SigIP6
planning)
Default/Recommen
1000~60000 1000 1000 S1SigIP6
ded Value
Default/Recommen
1000~60000 3000 3000 S1SigIP6
ded Value
Default/Recommen
1000~60000 1000 1000 S1SigIP6
ded Value
Default/Recommen
1~99 12 12 S1SigIP6
ded Value
Default/Recommen
1~99 25 25 S1SigIP6
ded Value
Default/Recommen
1000~60000 5000 5000 S1SigIP6
ded Value
Default/Recommen
2~254 10 10 S1SigIP6
ded Value
Default/Recommen
1~253 5 5 S1SigIP6
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) S1SigIP6
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) S1SigIP6
ded Value
Default/Recommen
ALDER32, CRC32 CRC32(CRC32) CRC32(CRC32) S1SigIP6
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) S1SigIP6
ded Value
Default/Recommen
1~254 10 10 S1SigIP6
ded Value
Transport
0~5 0 None Planning(Internal S1SigIP6
planning)
Transport
0~127 None None Planning(Internal SGW
planning)
Transport
Valid IP address None None Planning(Negotiatio SGW
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio SGW
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
0~15 characters NULL None Planning(Negotiatio SGW
n with the peer)
Transport
n with the peer)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio SGW
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
0~20 characters NULL None Planning(Internal SGW
planning)
Transport
0~5 0 None Planning(Negotiatio SGW
n with the peer)
Transport
1~15 characters None None Planning(Internal SGW6
planning)
Transport
Valid IP address None None Planning(Negotiatio SGW6
n with the peer)
The value DISABLE
is recommended if
the network does
not support IPv6
IPsec or an IPv6
IPsec tunnel has Transport
DISABLE, ENABLE DISABLE(Disable) already been Planning(Negotiatio SGW6
configured to n with the peer)
protect the IPv6
path set up using
the first service
IPv6 address of the
S-GW.
Transport
0~15 characters NULL None Planning(Negotiatio SGW6
n with the peer)
Transport
n with the peer)
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Negotiatio SGW6
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio SGW6
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
If the networking
mode does not
support IPSec or
IPSec tunnels are
Transport
to be set up by
manually
n with the peer)
configuring IPSec
MOs, this
parameter must be
set to DISABLE.
Transport
n with the peer)
Transport
n with the peer)
Transport
0~20 characters NULL None Planning(Internal SGW6
planning)
Transport
0~5 0 None Planning(Negotiatio SGW6
n with the peer)
Default/Recommen
0~7 0 0 X2ServIP
ded Value
Default/Recommen
0~1 0 0 X2ServIP
ded Value
Default/Recommen
0~7 None 7 X2ServIP
ded Value
Transport
1~15 characters None None Planning(Internal X2ServIP
planning)
Transport
Valid IP address None None Planning(Internal X2ServIP
planning)
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
Transport
has already been
DISABLE, ENABLE DISABLE(Disable) Planning(Internal X2ServIP
configured to
planning)
protect the SCTP
link set up using the
X2 service IP
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal X2ServIP
planning)
Transport
Valid IP address 0.0.0.0 0.0.0.0 Planning(Internal X2ServIP
planning)
Transport
0~15 characters NULL None Planning(Internal X2ServIP
planning)
Transport
0~15 characters NULL None Planning(Internal X2ServIP
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal X2ServIP
planning)
Transport
0~5 0 None Planning(Internal X2ServIP
planning)
Default/Recommen
0~7 0 0 X2SigIP
ded Value
Default/Recommen
0~1 0 0 X2SigIP
ded Value
Default/Recommen
0~7 None 7 X2SigIP
ded Value
Transport
1~15 characters None None Planning(Internal X2SigIP
planning)
Transport
Valid IP address None None Planning(Internal X2SigIP
planning)
The value DISABLE
is recommended if
the network does
not support IPSec
or an IPSec tunnel
Transport
has already been
DISABLE, ENABLE DISABLE(Disable) Planning(Internal X2SigIP
configured to
planning)
protect the SCTP
first X2 signaling IP
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal X2SigIP
planning)
Transport
Valid IP address 0.0.0.0 0.0.0.0 Planning(Internal X2SigIP
planning)
Transport
0~15 characters NULL None Planning(Internal X2SigIP
planning)
Transport
planning)
The value 0.0.0.0 is

Transport
recommended if
Valid IP address 0.0.0.0 Planning(Internal X2SigIP
SCTP multihoming
planning)
is not supported.
The value DISABLE
is recommended if
the network does
not support IPSec
or an IPSec tunnel
has already been Transport
DISABLE, ENABLE DISABLE(Disable) configured to Planning(Internal X2SigIP
protect the SCTP planning)
second X2
signaling IP
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal X2SigIP
planning)
Transport
Valid IP address 0.0.0.0 None Planning(Internal X2SigIP
planning)
Transport
planning)
Transport
planning)
Default/Recommen
1024~65535 36422 36422 X2SigIP
ded Value
Default/Recommen
10~59999 1000 1000 X2SigIP
ded Value
Default/Recommen
11~60000 3000 3000 X2SigIP
ded Value
Default/Recommen
10~59999 1000 1000 X2SigIP
ded Value
Default/Recommen
1~99 12 12 X2SigIP
ded Value
Default/Recommen
1~99 25 25 X2SigIP
ded Value
Default/Recommen
1000~60000 5000 5000 X2SigIP
ded Value
Default/Recommen
2~254 10 10 X2SigIP
ded Value
Default/Recommen
1~253 5 5 X2SigIP
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) X2SigIP
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) X2SigIP
ded Value
Default/Recommen
ALDER32, CRC32 CRC32(CRC32) CRC32(CRC32) X2SigIP
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) X2SigIP
ded Value
Default/Recommen
1~254 10 10 X2SigIP
ded Value
Default/Recommen
10~500 200 200 X2SigIP
ded Value
Transport
0~5 0 None Planning(Internal X2SigIP
planning)
Transport
16~79 None None Planning(Internal X2eNodeB
planning)
Transport
Valid IP address None None Planning(Negotiatio X2eNodeB
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
DISABLE, ENABLE DISABLE(Disable) configured to Planning(Negotiatio X2eNodeB
protect the SCTP n with the peer)
first signaling IP
address of the
neighboring
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Negotiatio X2eNodeB
n with the peer)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio X2eNodeB
n with the peer)
This parameter is
Transport
required only if
Valid IP address 0.0.0.0 Planning(Negotiatio X2eNodeB
SCTP multihoming
n with the peer)
is supported.
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
second signaling IP
address of the
neighboring
eNodeB.
Transport
n with the peer)
Transport
n with the peer)
Default/Recommen
1024~65535 36422 36422 X2eNodeB
ded Value
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
protect the IP path n with the peer)
set up using the
first service IP
address of the
neighboring
eNodeB.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
set up using the
second service IP
address of the
neighboring
eNodeB.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
set up using the
third service IP
address of the
neighboring
eNodeB.
Transport
n with the peer)
Transport
Same as the default
value
n with the peer)
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPSec
or an IPSec tunnel
set up using the
fourth service IP
address of the
neighboring
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) None Planning(Negotiatio X2eNodeB
n with the peer)
Transport
Same as the default
value
n with the peer)
Transport
This parameter is
000~999 460 Planning(Negotiatio X2eNodeB
set as required.
n with the peer)
Transport
This parameter is
00~99,000~999 20 Planning(Negotiatio X2eNodeB
set as required.
n with the peer)
Set this parameter

Transport
to the ID of the
0~1048575 0 Planning(Negotiatio X2eNodeB
neighboring
n with the peer)
eNodeB.
Transport
0~20 characters NULL None Planning(Internal X2eNodeB
planning)
Transport
0~5 0 None Planning(Negotiatio X2eNodeB
n with the peer)
Release_R10(Rele
Release_R9, None Planning(Negotiatio X2eNodeB
ase 10)
Transport
1~15 characters None None Planning(Internal X2ServIP6
planning)
Default/Recommen
0~7 0 0 X2ServIP6
ded Value
Default/Recommen
0~1 0 0 X2ServIP6
ded Value
Default/Recommen
0~7 None 7 X2ServIP6
ded Value
Transport
Valid IP address None None Planning(Internal X2ServIP6
planning)
The value DISABLE

is recommended if
the network does
not support IPv6
IPSec or an IPv6
IPSec tunnel has Transport
DISABLE, ENABLE DISABLE(Disable) already been Planning(Internal X2ServIP6
configured to planning)
protect the IPv6
path set up using
the X2 service IPv6
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal X2ServIP6
planning)
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal X2ServIP6
planning)
Transport
0~15 characters NULL None Planning(Internal X2ServIP6
planning)
Transport
0~15 characters NULL None Planning(Internal X2ServIP6
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal X2ServIP6
planning)
Transport
0~5 0 None Planning(Internal X2ServIP6
planning)
Transport
1~15 characters None None Planning(Internal X2SigIP6
planning)
Default/Recommen
0~7 0 0 X2SigIP6
ded Value
Default/Recommen
0~1 0 0 X2SigIP6
ded Value
Default/Recommen
0~7 None None X2SigIP6
ded Value
Transport
Valid IP address None None Planning(Internal X2SigIP6
planning)
The value DISABLE
is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
Transport
tunnel has already
DISABLE, ENABLE DISABLE(Disable) Planning(Internal X2SigIP6
been configured to
planning)
protect the SCTP
first X2 signaling
IPv6 address of the
local eNodeB.
The value DISABLE

is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
tunnel has already Transport
DISABLE, ENABLE DISABLE(Disable) been configured to Planning(Internal X2SigIP6
protect the IPv6 planning)
SCTP link set up
using the first X2
signaling IPv6
eNodeB.
Transport
Valid IP address 0:0:0:0:0:0:0:0 0.0.0.0 Planning(Internal X2SigIP6
planning)
Transport
0~15 characters NULL None Planning(Internal X2SigIP6
planning)
Transport
planning)
This parameter is
Transport
required only if
Valid IP address 0:0:0:0:0:0:0:0 Planning(Internal X2SigIP6
SCTP multihoming
planning)
is supported.
The value DISABLE
is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
protect the SCTP planning)
second X2
signaling IPv6
eNodeB.
The value DISABLE

is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
protect the IPv6 planning)
SCTP link set up
using the second
X2 signaling IPv6
eNodeB.
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Internal X2SigIP6
planning)
Transport
planning)
Transport
planning)
Default/Recommen
1024~65535 36422 36422 X2SigIP6
ded Value
Default/Recommen
1000~60000 1000 1000 X2SigIP6
ded Value
Default/Recommen
1000~60000 3000 3000 X2SigIP6
ded Value
Default/Recommen
1000~60000 1000 1000 X2SigIP6
ded Value
Default/Recommen
1~99 12 12 X2SigIP6
ded Value
Default/Recommen
1~99 25 25 X2SigIP6
ded Value
Default/Recommen
1000~60000 5000 5000 X2SigIP6
ded Value
Default/Recommen
2~254 10 10 X2SigIP6
ded Value
Default/Recommen
1~253 5 5 X2SigIP6
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) X2SigIP6
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) X2SigIP6
ded Value
Default/Recommen
ALDER32, CRC32 CRC32(CRC32) CRC32(CRC32) X2SigIP6
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) X2SigIP6
ded Value
Default/Recommen
1~254 10 10 X2SigIP6
ded Value
Transport
0~5 0 None Planning(Internal X2SigIP6
planning)
Transport
1~15 characters None None Planning(Internal X2eNodeB6
planning)
Transport
Valid IP address None None Planning(Negotiatio X2eNodeB6
n with the peer)
The value DISABLE

is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
DISABLE, ENABLE DISABLE(Disable) been configured to Planning(Negotiatio X2eNodeB6
address of the
neighboring IPv6
eNodeB.
The value DISABLE
is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
address of the
neighboring IPv6
eNodeB.
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Negotiatio X2eNodeB6
n with the peer)
This parameter is
Transport
required only if
Valid IP address 0:0:0:0:0:0:0:0 Planning(Negotiatio X2eNodeB6
SCTP multihoming
n with the peer)
is supported.
The value DISABLE

is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
second signaling
IPv6 address of the
neighboring IPv6
eNodeB.
The value DISABLE
is recommended if
IPv6 IPSec is not
used in the network
or an IPv6 IPSec
second signaling
IPv6 address of the
neighboring IPv6
eNodeB.
Transport
n with the peer)
Default/Recommen
1024~65535 36422 36422 X2eNodeB6
ded Value
Transport
n with the peer)
The value DISABLE
is recommended if
the network does
not support IPv6
IPSec or an IPv6
IPSec tunnel has
Transport
already been
DISABLE, ENABLE DISABLE(Disable) Planning(Negotiatio X2eNodeB6
configured to
n with the peer)
protect the IPv6
path set up using
the first service
IPv6 address of the
neighboring IPv6
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Negotiatio X2eNodeB6
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPv6
IPSec or an IPv6
IPSec tunnel has
Transport
already been
configured to
n with the peer)
protect the IPv6
path set up using
the second service
IPv6 address of the
neighboring IPv6
eNodeB.
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPv6
IPSec or an IPv6
IPSec tunnel has
Transport
already been
configured to
n with the peer)
protect the IPv6
path set up using
the third service
IPv6 address of the
neighboring IPv6
eNodeB.
Transport
n with the peer)
Transport
Same as the default
value
n with the peer)
Transport
n with the peer)
The value DISABLE

is recommended if
the network does
not support IPv6
IPSec or an IPv6
IPSec tunnel has
Transport
already been
configured to
n with the peer)
protect the IPv6
path set up using
the fourth service
IPv6 address of the
neighboring IPv6
eNodeB.
Transport
DISABLE, ENABLE DISABLE(Disable) None Planning(Negotiatio X2eNodeB6
n with the peer)
Transport
Same as the default
value
n with the peer)
Transport
This parameter is
000~999 460 Planning(Negotiatio X2eNodeB6
set as required.
n with the peer)
Transport
00~99,000~999 20 None Planning(Negotiatio X2eNodeB6
n with the peer)
Set this parameter Transport

0~1048575 0 to the ID of the peer Planning(Negotiatio X2eNodeB6
eNodeB. n with the peer)
Transport
0~20 characters NULL None Planning(Internal X2eNodeB6
planning)
Transport
0~5 0 None Planning(Negotiatio X2eNodeB6
n with the peer)
Release_R10(Rele
Release_R9, None Planning(Negotiatio X2eNodeB6
ase 10)
Transport
1~127 characters None None Planning(Internal CA
planning)
Transport
planning)
Transport
SHA1, SHA256 SHA1(SHA1) SHA1(SHA1) Planning(Internal CA
planning)
DEFAULT_MODE,
Transport
CFG_UPD_SIP, DEFAULT_MODE(
None Planning(Internal CA
CFG_INIT_UPD_A DEFAULT_MODE)
planning)
DDR
Transport
Valid IP address 0.0.0.0 None Planning(Internal CA
planning)
Transport
planning)
Transport
Valid IP address None None Planning(Internal CA
planning)
Transport
ESN, MAC, IP ESN(ESN) ESN(ESN) Planning(Internal CERTREQ
planning)
Transport
0~32 characters NULL None Planning(Internal CERTREQ
planning)
Transport
0~0,2~2 characters NULL None Planning(Internal CERTREQ
planning)
Transport
planning)
Transport
planning)
Transport
planning)
Transport
planning)
DATA_ENCIPHER DATA_ENCIPHER DATA_ENCIPHER

MENT, MENT:1, MENT:1,
DIGITAL_SIGNATU DIGITAL_SIGNATU DIGITAL_SIGNATU
Transport
RE, RE:1, RE:1,
Planning(Internal CERTREQ
KEY_AGREEMENT KEY_AGREEMENT KEY_AGREEMENT
planning)
, :1, :1,
KEY_ENCIPHERM KEY_ENCIPHERM KEY_ENCIPHERM
ENT ENT:1 ENT:1
Transport
SHA1, MD5,
SHA1(SHA1) SHA1(SHA1) Planning(Internal CERTREQ
SHA256
planning)
Transport
KEYSIZE1024, KEYSIZE2048(KEY KEYSIZE2048(KEY
Planning(Internal CERTREQ
KEYSIZE2048 SIZE2048) SIZE2048)
planning)
Transport
planning)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio CERTREQ
n with the peer)
Transport
1~64 characters None None Planning(Internal CERTMK
planning)
0~128 characters None None N/A CERTMK

Transport
IKE, SSL None None Planning(Internal APPCERT
planning)
Transport
1~64 characters None None Planning(Internal APPCERT
planning)
0~128 characters None None N/A APPCERT

Transport
0~15 characters NULL None Planning(Internal APPCERT
planning)
NORMALLY,
ABNORMALITY, None None N/A APPCERT
FILENOTEXIST
IKE, SSL None None N/A APPCERT
Transport
1~64 characters None None Planning(Internal CROSSCERT
planning)
0~128 characters None None N/A CROSSCERT

NORMALLY,
ABNORMALITY, None None N/A CROSSCERT
FILENOTEXIST
Transport
1~64 characters None None Planning(Internal TRUSTCERT
planning)
0~128 characters None None N/A TRUSTCERT
NORMALLY,
ABNORMALITY, None None N/A TRUSTCERT
FILENOTEXIST

Transport
1~64 characters None None Planning(Internal CRL
planning)
NORMAL,
CERTLOSS,
CERTDAMAGE, None None N/A CRL
UNKNOWFORMAT,
FAILED
0~128 characters None None N/A CRL
Transport
Valid IP address None None Planning(Internal CRLTSK
planning)
Transport
0~255 characters NULL None Planning(Internal CRLTSK
planning)
Transport
planning)
Transport
0~65535 389 389 Planning(Internal CRLTSK
planning)
Transport
1~64 characters None None Planning(Internal CRLTSK
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal CRLTSK
planning)
Transport
8~240 24 24 Planning(Internal CRLTSK
planning)
Transport
0~3 None None Planning(Internal CRLTSK
planning)
Transport
FTP, LDAP FTP(FTP) FTP(FTP) Planning(Internal CRLTSK
planning)
Transport
planning)
Transport
Valid IP address 0.0.0.0 None Planning(Internal CRLTSK
planning)
Transport
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Planning(Internal CERTCHKTSK
planning)
Default/Recommen
1~15 7 7 CERTCHKTSK
ded Value
Default/Recommen
7~180 30 30 CERTCHKTSK
ded Value
Transport
PROXY, CMP PROXY(PROXY) PROXY(PROXY) Planning(Internal CERTCHKTSK
planning)
NOVERIFY, Transport
NOVERIFY(No NOVERIFY(No
ALARM, Planning(Internal CRLPOLICY
Verifying) Verifying)
DISCONNECT planning)
Transport
3000~4999 None None Planning(Internal ACL
planning)
Transport
0~127 characters None None Planning(Internal ACL
planning)
Transport
3000~3999 None None Planning(Internal ACL6
planning)
Transport
0~127 characters None None Planning(Internal ACL6
planning)
Transport
3000~4999 None None Planning(Internal ACLRULE
planning)
Transport
planning)
Transport
DENY, PERMIT PERMIT(Permit) PERMIT(Permit) Planning(Internal ACLRULE
planning)
Transport
IP, ICMP, TCP,
None None Planning(Internal ACLRULE
UDP, SCTP
planning)
Transport
Valid IP address None None Planning(Negotiatio ACLRULE
n with the peer)
Transport
Valid wildcard of the
None None Planning(Negotiatio ACLRULE
IP address
n with the peer)
Transport
NO, YES None None Planning(Negotiatio ACLRULE
n with the peer)
OP_LT, OP_GT, Transport
OP_EQ, OP_NEQ, None None Planning(Internal ACLRULE
OP_RANGE planning)
Transport
planning)
Transport
planning)
Transport
Valid IP address None None Planning(Negotiatio ACLRULE
n with the peer)
Transport
Valid wildcard of the
None None Planning(Negotiatio ACLRULE
IP address
n with the peer)
Transport
NO, YES None None Planning(Negotiatio ACLRULE
n with the peer)
OP_EQ, OP_NEQ, None None Planning(Internal ACLRULE
OP_RANGE planning)
Transport
planning)
Transport
planning)
Transport
NO, YES NO(No) NO(No) Planning(Negotiatio ACLRULE
n with the peer)
Transport
planning)
Transport
NO, YES NO(No) NO(No) Planning(Negotiatio ACLRULE
n with the peer)
Transport
OP_EQ,
None None Planning(Internal ACLRULE
OP_RANGE
planning)
Transport
planning)
Transport
planning)
Transport
3000~3999 None None Planning(Internal ACLRULE6
planning)
Transport
planning)
Transport
DENY, PERMIT PERMIT(Permit) PERMIT(Permit) Planning(Internal ACLRULE6
planning)
Transport
IP6, TCP, UDP,
None None Planning(Internal ACLRULE6
ICMP6, SCTP
planning)
Transport
Valid IP address None None Planning(Negotiatio ACLRULE6
n with the peer)
Transport
0~128 None None Planning(Negotiatio ACLRULE6
n with the peer)
Transport
NO, YES None None Planning(Negotiatio ACLRULE6
n with the peer)
OP_EQ, OP_NEQ, None None Planning(Negotiatio ACLRULE6
OP_RANGE n with the peer)
Transport
n with the peer)
Transport
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio ACLRULE6
n with the peer)
Transport
n with the peer)
Transport
NO, YES None None Planning(Negotiatio ACLRULE6
n with the peer)
OP_EQ, OP_NEQ, None None Planning(Internal ACLRULE6
OP_RANGE planning)
Transport
planning)
Transport
planning)
Transport
NO, YES NO(No) NO(No) Planning(Negotiatio ACLRULE6
n with the peer)
Transport
planning)
Default/Recommen
0~7 0 0 BFDSESSION
ded Value
Default/Recommen
0~1 0 0 BFDSESSION
ded Value
Transport
0~7 None None Planning(Internal BFDSESSION
planning)
Transport
0~95 None None Planning(Internal BFDSESSION
planning)
Transport
Valid IP address None None Planning(Negotiatio BFDSESSION
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio BFDSESSION
n with the peer)
Transport
SINGLE_HOP,
None None Planning(Internal BFDSESSION
MULTI_HOP
planning)
Default/Recommen
10~1000 100 100 BFDSESSION
ded Value
Default/Recommen
10~1000 100 100 BFDSESSION
ded Value
Default/Recommen
3~10 3 3 BFDSESSION
ded Value
MAINTENANCE, RELIABILITY(Relia RELIABILITY(Relia Default/Recommen
BFDSESSION
RELIABILITY bility) bility) ded Value
Default/Recommen
0~63 48 48 BFDSESSION
ded Value
NO, YES NO(No) NO(No) N/A BFDSESSION
ADMINDOWN,
None None N/A BFDSESSION
DOWN, INIT, UP
ASYNCHRONOUS
_MODE
10~1000 None None N/A BFDSESSION


NO_DIAGNOSTIC,
CTRL_DECT_TIME
_EXPIRED,
ECHO_FUNC_FAIL
ED,
NEIGHBOR_SIG_S
ESSION_DOWN,
FORDWARDING_P
LANE_RESET,
PATH_DOWN,
CONCATENATED_
PATH_DOWN,
ADMIN_DOWN,
REVERSE_CONCA
TENTATED_PATH_
DOWN,
PEER_ADMIN_DO
WN
Transport
DRAFT4,
DRAFT4(DRAFT4) DRAFT4(DRAFT4) Planning(Internal BFDSESSION
STANDARD
planning)
DEFAULT, Default/Recommen
DEFAULT(Default) None CERTDEPLOY
SPECIFIC ded Value
Default/Recommen
0~7 0 None CERTDEPLOY
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Digits 0 to 9 and
Transport
letters a to z and A
1~43 characters None Planning(Internal CFMBNDIP
to Z are
planning)
recommended.
Digits 0 to 9 and
Transport
1~43 characters None Planning(Internal CFMBNDIP
to Z are
planning)
recommended.
Transport
1~8191 None None Planning(Negotiatio CFMBNDIP
n with the peer)
Transport
Valid IP address None None Planning(Internal CFMBNDIP
planning)
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMMA
recommended for
planning)
the MDNAME value
of a CFM MA.
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMMA
recommended for
planning)
the MANAME value
of a CFM MA.
Default/Recommen
0~7 0 0 CFMMA
ded Value
Default/Recommen
0~1 0 0 CFMMA
ded Value
Transport
0~7 None None Planning(Internal CFMMA
planning)
Transport
NO, YES YES(Yes) YES(Yes) Planning(Internal CFMMA
planning)
Transport
1~4094 1 None Planning(Internal CFMMA
planning)
Transport
0~7 0 0 Planning(Internal CFMMA
planning)
10ms, 100ms, 1s, Default/Recommen

1s(1s) 1s(1s) CFMMA
10s, 1min, 10min ded Value
0~32 None None N/A CFMMA
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMMD
recommended for
planning)
the MDNAME value
of a CFM MD.
Default/Recommen
0~7 0 0 CFMMD
ded Value
0~4294967295 None None N/A CFMMD
None None None N/A CFMMD
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMMEP
recommended for
planning)
the MDNAME value
of a CFM MEP.
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMMEP
recommended for
planning)
the MANAME value
of a CFM MEP.
Transport
1~8191 None None Planning(Internal CFMMEP
planning)
Default/Recommen
0~7 0 0 CFMMEP
ded Value
Default/Recommen
0~1 0 0 CFMMEP
ded Value
Transport
planning)
BASE_BOARD, Transport
ETH_COVERBOAR None None Planning(Internal CFMMEP
D planning)
Transport
ETH, ETHTRK None None Planning(Internal CFMMEP
planning)
Transport
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal CFMMEP
planning)
NO, YES YES(Yes) YES(Yes) N/A CFMMEP

1~4094 None None N/A CFMMEP
0~7 0 0 N/A CFMMEP
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMRMEP
recommended for
planning)
the MDNAME value
of a CFM RMEP.
Digits 0 to 9 and
Transport
to Z are
1~43 characters None Planning(Internal CFMRMEP
recommended for
planning)
the MANAME value
of a CFM RMEP.
Transport
1~8191 None None Planning(Negotiatio CFMRMEP
n with the peer)
Transport
14 characters 0000-0000-0000 None Planning(Internal CFMRMEP
planning)
NORMAL, FAULT None None N/A CFMRMEP
14 characters None None N/A CFMRMEP
NO, YES NO(No) NO(No) N/A CFMRMEP
0~4294967295 None None N/A CFMRMEP

Valid IP address None None N/A CFMRMEP
Transport
TCP, UDP None None Planning(Internal DBGSVR
planning)
22, 23, 67, 68, 80,

319, 320, 443, 500,
1110, 1120, 2700,
Transport
3784, 4443, 4500,
None None Planning(Internal DBGSVR
4784, 6000, 6001,
planning)
6006, 6007, 17185,
30023, 33003,
45300
Transport
DISABLE, ENABLE None None Planning(Internal DBGSVR
planning)
Default/Recommen
0~7 0 0 DEVIP
ded Value
Default/Recommen
0~1 0 0 DEVIP
ded Value
Transport
0~7 None None Planning(Internal DEVIP
planning)
BASE_BOARD,
, None None Planning(Internal DEVIP
D
Transport
PPP, MPGRP, ETH,
None None Planning(Internal DEVIP
ETHTRK, LOOPINT
planning)
Transport
0~15 None None Planning(Internal DEVIP
planning)
Transport
Valid IP address None None Planning(Internal DEVIP
planning)
Transport
Valid Mask address None None Planning(Internal DEVIP
planning)
Transport
1~65535 None None Planning(Internal DEVIP6
planning)
Transport
Valid IP address None None Planning(Internal DEVIP6
planning)
Transport
1~128 None None Planning(Internal DEVIP6
planning)
IP6_DAD_OK,
IP6_DAD_TENTATI
VE,
IP6_DAD_DUPLIC None None N/A DEVIP6
ATED,
IP6_DAD_UNKNO
W
0~4294967295 None None N/A DEVIP6

0~4294967295 None None N/A DEVIP6
Transport
DHCPRELAYSWIT
DISABLE, ENABLE DISABLE(Disable) ENABLE(ENABLE) Planning(Internal
CH
planning)
Transport
Valid IP address None None Planning(Internal DHCPSVRIP
planning)
Transport
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Planning(Negotiatio DHCPSW
n with the peer)
IPPRECEDENCE, Default/Recommen
DSCP(DSCP) DSCP(DSCP) DIFPRI
DSCP ded Value
Default/Recommen
0~63 46 46 DIFPRI
ded Value
Default/Recommen
0~63 46 46 DIFPRI
ded Value
Default/Recommen
0~63 14 14 DIFPRI
ded Value
Default/Recommen
0~63 46 46 DIFPRI
ded Value
Default/Recommen
0~63 46 46 DIFPRI
ded Value
Default/Recommen
HQ, LQ HQ(High Quality) HQ(High Quality) DIFPRI
ded Value
Default/Recommen
0~100 100 100 DIFPRI
ded Value
Default/Recommen
0~1000 0 0 DIFPRI
ded Value
Default/Recommen
0~63 26 26 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 100 100 DIFPRI
ded Value
Default/Recommen
0~1000 0 0 DIFPRI
ded Value
Default/Recommen
0~63 34 34 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 100 100 DIFPRI
ded Value
Default/Recommen
0~1000 0 0 DIFPRI
ded Value
Default/Recommen
0~63 26 26 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 100 100 DIFPRI
ded Value
Default/Recommen
0~1000 0 0 DIFPRI
ded Value
Default/Recommen
0~63 46 46 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 100 100 DIFPRI
ded Value
Default/Recommen
0~1000 0 0 DIFPRI
ded Value
Default/Recommen
0~63 18 18 DIFPRI
ded Value
Default/Recommen
HQ, LQ LQ(Low Quality) LQ(Low Quality) DIFPRI
ded Value
Default/Recommen
0~100 30 30 DIFPRI
ded Value
Default/Recommen
0~1000 100 100 DIFPRI
ded Value
Default/Recommen
0~63 18 18 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 30 30 DIFPRI
ded Value
Default/Recommen
0~1000 100 100 DIFPRI
ded Value
Default/Recommen
0~63 10 10 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 30 30 DIFPRI
ded Value
Default/Recommen
0~1000 100 100 DIFPRI
ded Value
Default/Recommen
0~63 0 0 DIFPRI
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 30 30 DIFPRI
ded Value
Default/Recommen
0~1000 100 100 DIFPRI
ded Value
OFF, ON ON(On) ON(On) Engineering Design DLITFCALG

OFF, ON ON(On) ON(On) Engineering Design DLITFCALG
Default/Recommen
0~7 0 None DOT1X
ded Value
Default/Recommen
0~1 0 None DOT1X
ded Value
Transport
0~7 None None Planning(Internal DOT1X
planning)
ETH_COVERBOAR None None Planning(Internal DOT1X
D planning)
Transport
0~5 None None Planning(Internal DOT1X
planning)
Transport
EAP-TLS(EAP-TLS EAP-TLS(EAP-TLS
EAP-TLS Planning(Internal DOT1X
authentic method) authentic method)
planning)
0~4294967295 None None N/A DOT1X
NULL, LIC_OFF,
NOTIFY_FAIL,
None None N/A DOT1X
NO_CERT,
PORT_DOWN

UNAUTHENTICAT
ED,
AUTHENTICATING
,
AUTHENTIC_SUC None None N/A DOT1X
CEED,
AUTHENTIC_FAIL,
DHCP_AUTHENTI
CATING
Transport
0~63 None 0 Planning(Internal DSCPMAP
planning)
Transport
0~7 None 0 Planning(Internal DSCPMAP
planning)
Default/Recommen
0~7 0 0 E1T1
ded Value
Default/Recommen
0~1 0 0 E1T1
ded Value
Transport
0~7 None None Planning(Internal E1T1
planning)
Transport
0~7,255 255 None Planning(Internal E1T1
planning)
Transport
ALLPORT,
ALLPORT(All Ports) ALLPORT(All Ports) Planning(Internal E1T1
SINGLEPORT
planning)
Transport
E1_UNBA, E1_BA, E1_UNBA(E1 E1_UNBA(E1
Planning(Internal E1T1
T1 Unbalance) Unbalance)
planning)
E1_DOUBLE_FRA
ME,
E1_CRC4_MULTI_
E1_CRC4_MULTI_ Transport
FRAME,
None FRAME(E1 CRC4 Planning(Internal E1T1
T1_SUPER_FRAM
Multiple Frames) planning)
E,
T1_EXTENDED_S
UPER_FRAME
If an E1/T1 port is
carried over IP, the Transport
HDB3, AMI, B8ZS None AMI line coding Planning(Internal E1T1
mode is not planning)
recommended.
SLAVE(Slave SLAVE(Slave Default/Recommen
MASTER, SLAVE E1T1
Mode) Mode) ded Value
OK, LOCAL_LOOP,
REMOTE_LOOP,
PAYLOAD_LOOP,
SINGLE_CH_LOOP
, LOS, AIS, LFA, None None N/A E1T1
RA, LMFA, SLIP,
OTHERS,
BACKUP,
PHYSICAL_LOOP
EXECUTELINKTES
TFlAG_0,
EXECUTELINKTES
None None N/A E1T1
TFlAG_1,
EXECUTELINKTES
TFlAG_2
NO, YES None None N/A E1T1
0~720 None None N/A E1T1
Transport
BASE_BOARD,
None None Planning(Internal E1T1
E1_COVERBOARD
planning)
E1_UNBA, E1_BA,
None None N/A E1T1
T1, UNKNOWN
E1_DOUBLE_FRA
ME,
E1_CRC4_MULTI_
FRAME,
T1_SUPER_FRAM
E, None None N/A E1T1
T1_EXTENDED_S
UPER_FRAME,
E1_MODIFY_CRC4
_MULTIFRAME,
UNKNOWN
HDB3, AMI, B8ZS,

None None N/A E1T1
UNKNOWN
1E-3, 1E-4, 1E-5, Default/Recommen

1E-5(1E-5) 1E-5(1E-5) E1T1BER
1E-6 ded Value
Default/Recommen
0~7 0 0 ETHOAM3AH
ded Value
Default/Recommen
0~1 0 0 ETHOAM3AH
ded Value
Transport
0~7 None None Planning(Internal ETHOAM3AH
planning)
ETH_COVERBOAR None None Planning(Internal ETHOAM3AH
D planning)
Transport
ETH None None Planning(Internal ETHOAM3AH
planning)
Transport
0~5 None None Planning(Internal ETHOAM3AH
planning)
ACTIVE(Active ACTIVE(Active Default/Recommen

PASSIVE, ACTIVE ETHOAM3AH
10,20,50,100,200,5 Default/Recommen
1000 1000 ETHOAM3AH
00,1000 ded Value
Default/Recommen
64~1518 128 128 ETHOAM3AH
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) ETHOAM3AH
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) ETHOAM3AH
ded Value
Default/Recommen
1~60 1 1 ETHOAM3AH
ded Value
Default/Recommen
1~65535 1 1 ETHOAM3AH
ded Value
Default/Recommen
10~900 60 60 ETHOAM3AH
ded Value
Default/Recommen
1~900 1 1 ETHOAM3AH
ded Value
OAM3AH_SESSIO
N_IDLE,
OAM3AH_SESSIO
N_DISCOVER,
OAM3AH_SESSIO
None None N/A ETHOAM3AH
N_DETECT,
OAM3AH_SESSIO
N_LB_LOCAL,
OAM3AH_SESSIO
N_LB_REMOTE
0~4294967295 None None N/A ETHOAM3AH


Default/Recommen
0~7 0 0 ETHPORT
ded Value
Default/Recommen
0~1 0 0 ETHPORT
ded Value
Transport
0~7 None None Planning(Internal ETHPORT
planning)
ETH_COVERBOAR None None Planning(Internal ETHPORT
D planning)
Transport
0~5 None None Planning(Internal ETHPORT
planning)
If an optical fiber is
used for
transmission, set
this parameter to
Transport
COPPER, FIBER, FIBER.
None Planning(Internal ETHPORT
AUTO If an electrical cable
planning)
is used for
transmission, set
this parameter to
COPPER.
Default/Recommen
46~1800 1500 1500 ETHPORT
ded Value
10M, 100M, 1000M, AUTO(Automatic AUTO(Automatic Default/Recommen
ETHPORT
AUTO Negotiation) Negotiation) ded Value
AUTO(Automatic Default/Recommen
FULL, AUTO FULL(Full Duplex) ETHPORT
Negotiation) ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) ETHPORT
ded Value
Default/Recommen
CLOSE, OPEN OPEN(Open) OPEN(Open) ETHPORT
ded Value
Default/Recommen
0~100 10 10 ETHPORT
ded Value
Default/Recommen
0~100 8 8 ETHPORT
ded Value
14 characters None None N/A ETHPORT

UP, DOWN None None N/A ETHPORT
NOLOOP,
None None N/A ETHPORT
REMOTE
NO, YES None None N/A ETHPORT
DISABLE, ENABLE None None N/A ETHPORT
0~4294967295 None None N/A ETHPORT
Valid IP address None None N/A ETHPORT
FORCE, AUTO None None N/A ETHPORT

FORCE, AUTO None None N/A ETHPORT
10M, 100M, 1000M,

AUTO
HALF, FULL, AUTO None None N/A ETHPORT
FORCE, AUTO,
UNKNOWN
10M, 100M, 1000M,

AUTO, UNKNOWN
HALF, FULL,
AUTO, UNKNOWN
UP, DOWN None None N/A ETHPORT
Default/Recommen
0~7 0 0 ETHTRK
ded Value
Default/Recommen
0~1 0 0 ETHTRK
ded Value
Transport
0~7 None None Planning(Internal ETHTRK
planning)
Default/Recommen
0~2 0 0 ETHTRK
ded Value
ENABLE(Enable ENABLE(Enable Default/Recommen

DISABLE, ENABLE ETHTRK
LACP) LACP) ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) ETHTRK
ded Value
ETH_COVERBOAR None None Planning(Internal ETHTRK
D planning)
Default/Recommen
46~1800 1500 1500 ETHTRK
ded Value
UP, DOWN None None N/A ETHTRK
14 characters None None N/A ETHTRK

14 characters None None N/A ETHTRK
0~2 None None N/A ETHTRK
0~7 characters None None N/A ETHTRK
0~7 characters None None N/A ETHTRK

Valid IP address None None N/A ETHTRK
Default/Recommen
0~7 0 0 ETHTRKLNK
ded Value
Default/Recommen
0~1 0 0 ETHTRKLNK
ded Value
Transport
0~7 None None Planning(Internal ETHTRKLNK
planning)
Transport
0~2 0 0 Planning(Internal ETHTRKLNK
planning)
Transport
0~5 None None Planning(Internal ETHTRKLNK
planning)
Default/Recommen
0~255 255 255 ETHTRKLNK
ded Value
Transport
NO, YES None None Planning(Internal ETHTRKLNK
planning)
ETH_COVERBOAR None None Planning(Internal ETHTRKLNK
D planning)
UP, DOWN None None N/A ETHTRKLNK

14 characters None None N/A ETHTRKLNK
SHORT, LONG,
None None N/A ETHTRKLNK
NULL
SHORT, LONG,
None None N/A ETHTRKLNK
NULL
0~4294967295 None None N/A ETHTRKLNK
0~4294967295 None None N/A ETHTRKLNK
Transport
10~254 None None Planning(Internal EXTUDT
planning)
Transport
0~39 None None Planning(Internal EXTUDT
planning)
Transport
0~39 None None Planning(Internal EXTUDTPARAGRP
planning)
Transport
planning)
Transport
0~100 0 None Planning(Internal EXTUDTPARAGRP
planning)
Transport
HQ, LQ None None Planning(Internal EXTUDTPARAGRP
planning)
Transport
planning)
Transport
planning)
Transport
ARP, ICMP, TCP,
None None Planning(Internal FLOODDEFEND
SYN, UDP
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) None Planning(Internal FLOODDEFEND
planning)
If FLDTYPE is set
to ARP or SYN, the
recommended
value is 64. If
FLDTYPE is set to
Transport
ICMP, the
1~4096 None Planning(Internal FLOODDEFEND
recommended
planning)
value is 128. If
FLDTYPE is set to
TCP or UDP, the
recommended
value is 2048.
Transport
DISABLE, ENABLE DISABLE(Disable) None Planning(Internal FLOODDEFEND
planning)
If FLDTYPE is set
to ARP or SYN, the
recommended
value is 32. If
FLDTYPE is set to
Transport
ICMP, the
1~4096 None Planning(Internal FLOODDEFEND
recommended
planning)
value is 64. If
FLDTYPE is set to
TCP or UDP, the
recommended
value is 1024.
0~4294967295 None None N/A FLOODDEFEND
0~4294967295 None None N/A FLOODDEFEND

DISABLE, ENABLE DISABLE(Disable) None Engineering Design GTRANSPARA
SINGLE_RATE, SINGLE_RATE(Sin
None Engineering Design GTRANSPARA
DUAL_RATE gle Rate)
0~1200 30 None Engineering Design GTRANSPARA
5~20 20 20 Engineering Design GTRANSPARA

Transport
0~31 characters NULL None Planning(Negotiatio IKECFG
n with the peer)
Default/Recommen
0,20~28800 0 0 IKECFG
ded Value
Default/Recommen
0,60~28800 0 0 IKECFG
ded Value
Transport
0~63 48 None Planning(Internal IKECFG
planning)
0~7 0 None N/A IKECFG
0~1 None None N/A IKECFG
0~7 None None N/A IKECFG

Transport
1~15 characters None None Planning(Internal IKEPEER
planning)
Transport
1~99 None None Planning(Internal IKEPEER
planning)
Transport
IKE_V1, IKE_V2 IKE_V2(IKE V2) IKE_V2(IKE_V2) Planning(Internal IKEPEER
planning)
Transport
MAIN,
MAIN(Main Mode) MAIN(Main Mode) Planning(Internal IKEPEER
AGGRESSIVE
planning)
Transport
IP, FQDN None None Planning(Internal IKEPEER
planning)
Transport
Valid IP address None None Planning(Negotiatio IKEPEER
n with the peer)
Transport
planning)
Transport
planning)
Transport
DISABLE, PERIODIC(Periodic PERIODIC(Periodic
Planning(Internal IKEPEER
PERIODIC ) )
planning)
Default/Recommen
10~3600 10 10 IKEPEER
ded Value
Default/Recommen
3~30 5 5 IKEPEER
ded Value
Default/Recommen
3~10 5 5 IKEPEER
ded Value
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio IKEPEER
n with the peer)
0~7 0 None N/A IKEPEER

Transport
1~15 characters None None Planning(Internal IKEPEER6
planning)
Transport
1~99 None None Planning(Internal IKEPEER6
planning)
Transport
IKE_V1, IKE_V2 IKE_V2(IKE V2) IKE_V2(IKE V2) Planning(Internal IKEPEER6
planning)
Transport
MAIN,
MAIN(Main Mode) MAIN(Main Mode) Planning(Negotiatio IKEPEER6
AGGRESSIVE
n with the peer)
Transport
FQDN, IPV6 None None Planning(Internal IKEPEER6
planning)
Transport
Valid IP address None None Planning(Negotiatio IKEPEER6
n with the peer)
Transport
planning)
Transport
planning)
Transport
DISABLE, PERIODIC(Periodic PERIODIC(Periodic
Planning(Internal IKEPEER6
PERIODIC ) )
planning)
Default/Recommen
10~3600 10 10 IKEPEER6
ded Value
Default/Recommen
3~30 5 5 IKEPEER6
ded Value
Default/Recommen
3~10 5 5 IKEPEER6
ded Value
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Negotiatio IKEPEER6
n with the peer)
0~7 0 None N/A IKEPEER6

Transport
1~99 None None Planning(Internal IKEPROPOSAL
planning)
DES, 3DES, Transport

AES128, AES192, AES128(AES128) AES128(AES128) Planning(Internal IKEPROPOSAL
AES256 planning)
Transport
MD5, SHA1,
SHA1(SHA1) SHA1(SHA1) Planning(Internal IKEPROPOSAL
AES_XCBC_96
planning)
Transport
PRE_SHARED_KE PRE_SHARED_KE PRE_SHARED_KE
Planning(Internal IKEPROPOSAL
Y, IKE_RSA_SIG Y(Pre-shared Key) Y(Pre-shared Key)
planning)
DH_GROUP1,
DH_GROUP2(1024 DH_GROUP2(1024 Transport
DH_GROUP2,
-bit Diffie-Hellman -bit Diffie-Hellman Planning(Internal IKEPROPOSAL
DH_GROUP14,
Group) Group) planning)
DH_GROUP15
Default/Recommen
60~604800 86400 86400 IKEPROPOSAL
ded Value
HMAC_MD5,
HMAC_SHA1(HMA HMAC_SHA1(HMA Default/Recommen
HMAC_SHA1, IKEPROPOSAL
C_SHA1) C_SHA1) ded Value
AES128_XCBC
0~7 0 None N/A IKEPROPOSAL
Default/Recommen
0~7 0 0 IP2RSCGRP
ded Value
Default/Recommen
0~1 0 0 IP2RSCGRP
ded Value
Transport
0~7 None None Planning(Internal IP2RSCGRP
planning)
Transport
0~15 0 0 Planning(Internal IP2RSCGRP
planning)
Transport
Valid IP address None None Planning(Negotiatio IP2RSCGRP
n with the peer)
Transport
Valid Mask address None None Planning(Internal IP2RSCGRP
planning)
Transport
IP IP(IP) None Planning(Internal IP2RSCGRP
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal IP2RSCGRP
D
Transport
PPP, MPGRP, ETH,
None None Planning(Internal IP2RSCGRP
ETHTRK, TUNNEL
planning)
Transport
0~15 0 0 Planning(Internal IP2RSCGRP
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) None Planning(Internal IPGUARD
planning)
Default/Recommen
10~1000 120 None IPGUARD
ded Value
Transport
planning)
Transport
planning)
Default/Recommen
ded Value
Transport
planning)
Default/Recommen
ded Value
PPP, MPGRP, ETH,

None None N/A IPGUARD
ETHTRK, LOOPINT
0~15 None None N/A IPGUARD
14 characters None None N/A IPGUARD
14 characters None None N/A IPGUARD
IPV4, ARP, RARP,

IPV6, 802_1X,
LLDP, 1588V2,
CFM, LACP, 3AH
Valid IP address None None N/A IPGUARD
Valid IP address None None N/A IPGUARD
ICMP, TCP, UDP,

SCTP
0~200 characters None None N/A IPGUARD
Transport
1~65535 None None Planning(Internal IPITF6
planning)
Transport
NORMAL, VLAN NORMAL(Normal) NORMAL(Normal) Planning(Internal IPITF6
planning)
Default/Recommen
0~7 0 0 IPITF6
ded Value
Default/Recommen
0~1 0 0 IPITF6
ded Value
Transport
planning)
Transport
BASE_BOARD None None Planning(Internal IPITF6
planning)
Transport
ETH, TRUNK,
None None Planning(Internal IPITF6
LOOPIF
planning)
Transport
planning)
Transport
planning)
Default/Recommen
1280~1800 1500 None IPITF6
ded Value
UP, DOWN None None N/A IPITF6
Valid IP address None None N/A IPITF6
0~8 None None N/A IPITF6
DISABLE, ENABLE None None N/A IPITF6

Transport
0~65535 None None Planning(Internal IPPATH
planning)
Default/Recommen
0~7 0 0 IPPATH
ded Value
Default/Recommen
0~1 0 0 IPPATH
ded Value
Transport
planning)
Transport
PPP, MPGRP, ETH,
None None Planning(Internal IPPATH
ETHTRK, TUNNEL
planning)
Transport
0~15 0 0 Planning(Internal IPPATH
planning)
It is recommended
that IP Path be set
to QOS in a
Multiple Spanning
Tree Protocol Default/Recommen
QOS, ANY ANY(ANY) IPPATH
(MSTP) network. In ded Value
other scenarios, it is
recommended that
this parameter is
set to ANY.
Transport
planning)
Transport
Valid IP address None None Planning(Negotiatio IPPATH
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio IPPATH
n with the peer)
If the IP path
belongs to the S1
interface, this
parameter is set 0. Transport
0~79 None If the IP path Planning(Internal IPPATH
belongs to the X2 planning)
interface, this
parameter is set
from 16 to 79.
Default/Recommen
HQ, LQ HQ(High Quality) HQ(High Quality) IPPATH
ded Value
Transport
S1, X2 None S1(S1) Planning(Internal IPPATH
planning)
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) IPPATH
ded Value
0~4294967294 None None N/A IPPATH

NORMAL, FAULT,
CHECK_DISABLE None None N/A IPPATH
D
Transport
planning)
Transport
0~47 characters NULL None Planning(Internal IPPATH
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal IPPATH
D
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) IPPATH
ded Value
Transport
0~65535 None None Planning(Internal IPPATH6
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal IPPATH6
planning)
Transport
0~15 None 0 Planning(Internal IPPATH6
planning)
Transport
planning)
Transport
QOS, ANY None None Planning(Internal IPPATH6
planning)
Transport
planning)
Transport
Valid IP address None None Planning(Negotiatio IPPATH6
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio IPPATH6
n with the peer)
If the IPv6 path

belongs to the S1
interface, this
parameter is set 0. Transport
0~79 None If the IPv6 path Planning(Internal IPPATH6
belongs to the X2 planning)
interface, this
parameter is set
from 16 to 79.
Transport
S1, X2 None None Planning(Internal IPPATH6
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal IPPATH6
planning)
0~4294967295 None None N/A IPPATH6
NORMAL, FAULT,
CHECK_DISABLE None None N/A IPPATH6
D
Transport
0~47 characters NULL None Planning(Internal IPPATH6
planning)
Transport
Valid IP address None None Planning(Negotiatio IPPATHRT
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio IPPATHRT
n with the peer)
Transport
HQ, LQ None None Planning(Internal IPPATHRT
planning)
Transport
Valid IP address None None Planning(Internal IPPATHRT
planning)
Transport
0~65535 None None Planning(Internal IPPMSESSION
planning)
Transport
Valid IP address None None Planning(Negotiatio IPPMSESSION
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio IPPMSESSION
n with the peer)
Transport
planning)
Transport
UP, BIDIR UP(Uplink) UP(Uplink) Planning(Internal IPPMSESSION
planning)
0~10000 None None N/A IPPMSESSION

-10000~10000 None None N/A IPPMSESSION
-10000~10000 None None N/A IPPMSESSION
IDLE, ACTING,
PMUP, DEACTING, None None N/A IPPMSESSION
UNKNOWN
IDLE, ACTING,
PMUP, DEACTING, None None N/A IPPMSESSION
UNKNOWN
FOUR_TUPLE, FOUR_TUPLE(FO FOUR_TUPLE(FO Default/Recommen

IPPMSESSION
THREE_TUPLE UR_TUPLE) UR_TUPLE) ded Value
Default/Recommen
NO, YES NO(No) NO(No) IPPMSESSION
ded Value
Transport
planning)
NO, YES None None N/A IPPMSESSION
None None None N/A IPPMSESSION
NO, YES None None N/A IPPMSESSION

None None None N/A IPPMSESSION
IPPMVER_V1,
None None N/A IPPMSESSION
IPPMVER_V2
Default/Recommen
0~7 0 0 IPRT
ded Value
Default/Recommen
0~1 0 0 IPRT
ded Value
Transport
0~7 None None Planning(Internal IPRT
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal IPRT
D
Transport
PPP, MPGRP,
PPP(PPP Link) None Planning(Internal IPRT
TUNNEL
planning)
Transport
0~15 0 0 Planning(Internal IPRT
planning)
Transport
NEXTHOP, IF None None Planning(Internal IPRT
planning)
Transport
Valid IP address None None Planning(Negotiatio IPRT
n with the peer)
Transport
Valid Mask address None None Planning(Internal IPRT
planning)
Transport
Valid IP address 0 None Planning(Internal IPRT
planning)
Transport
1~255 60 60 Planning(Internal IPRT
planning)
STATICHOST,
STATICGATEWAY, None None N/A IPRT
HOST, GATEWAY
Transport
0~47 characters NULL None Planning(Internal IPRT
planning)
PPP, MPGRP, ETH,

ETHTRK,
None None N/A IPRT
LOOPINT, VI,
TUNNEL
0~32 None None N/A IPRT

Transport
Valid IP address None None Planning(Negotiatio IPRT6
n with the peer)
Transport
0~128 None None Planning(Internal IPRT6
planning)
Transport
NEXTHOP(Next NEXTHOP(Next
NEXTHOP Planning(Internal IPRT6
Hop) Hop)
planning)
IPADDR6_TYPE_G
Transport
LOBAL_UNICAST,
None None Planning(Internal IPRT6
IPADDR6_TYPE_LI
planning)
NK_LOCAL
Transport
Valid IP address None None Planning(Internal IPRT6
planning)
Transport
1~65535 1 None Planning(Internal IPRT6
planning)
Transport
1~255 60 60 Planning(Internal IPRT6
planning)
STATICHOST,
STATICGATEWAY, None None N/A IPRT6
HOST, GATEWAY
Transport
0~47 characters NULL None Planning(Internal IPRT6
planning)
Default/Recommen
0~7 0 0 IPSECBIND
ded Value
Default/Recommen
0~1 0 0 IPSECBIND
ded Value
Transport
0~7 None None Planning(Internal IPSECBIND
planning)
ETH_COVERBOAR None None Planning(Internal IPSECBIND
D planning)
Transport
ETH, ETHTRK None None Planning(Internal IPSECBIND
planning)
Transport
0~5 None None Planning(Internal IPSECBIND
planning)
Transport
1~15 characters None None Planning(Internal IPSECBIND
planning)
Transport
1~65535 None None Planning(Internal IPSECBIND6
planning)
Transport
1~15 characters None None Planning(Internal IPSECBIND6
planning)
Transport
0~49 None None Planning(Internal IPSECDTNL
planning)
Transport
1~15 characters None None Planning(Internal IPSECDTNL
planning)
Transport
planning)
Transport
1~15 characters None None Planning(Internal IPSECDTNL
planning)
Transport
planning)
Transport
planning)
Transport
planning)
MASTER, SLAVE None None N/A IPSECDTNL
Transport
1~15 characters None None Planning(Internal IPSECPOLICY
planning)
Transport
1~10000 None None Planning(Internal IPSECPOLICY
planning)
Transport
3000~3999 None None Planning(Internal IPSECPOLICY
planning)
Transport
planning)
Transport
planning)
DISABLE, Transport
PFS_GROUP1, DISABLE(Disable) DISABLE(Disable) Planning(Internal IPSECPOLICY
Transport
LOCAL(Local LOCAL(Local
GLOBAL, LOCAL Planning(Internal IPSECPOLICY
Configuration) Configuration)
planning)
Default/Recommen
30~604800 3600 3600 IPSECPOLICY
ded Value
69120000 69120000 IPSECPOLICY
7295 ded Value
0~7 0 None N/A IPSECPOLICY

WND_DISABLE,
WND_32, WND_64,
WND_128,
WND_256, Default/Recommen
WND_DISABLE(0) None IPSECPOLICY
WND_512, ded Value
WND_1024,
WND_2048,
WND_4096
Transport
1~15 characters None None Planning(Internal IPSECPOLICY6
planning)
Transport
1~10000 None None Planning(Internal IPSECPOLICY6
planning)
Transport
IPV4, IPV6 None None Planning(Internal IPSECPOLICY6
planning)
Transport
planning)
Transport
planning)
Transport
planning)
Transport
planning)
DISABLE, Transport
PFS_GROUP1, DISABLE(Disable) DISABLE(Disable) Planning(Internal IPSECPOLICY6
Transport
LOCAL(Local LOCAL(Local
GLOBAL, LOCAL Planning(Internal IPSECPOLICY6
Configuration) Configuration)
planning)
Default/Recommen
30~604800 3600 3600 IPSECPOLICY6
ded Value
69120000 69120000 IPSECPOLICY6
7295 ded Value
0~7 0 None N/A IPSECPOLICY6

Transport
1~15 characters None None Planning(Internal IPSECPROPOSAL
planning)
TUNNEL, Default/Recommen
TUNNEL(Tunnel) TUNNEL(Tunnel) IPSECPROPOSAL
TRANSPORT ded Value
Transport
AH, ESP, AH_ESP ESP(ESP Protocol) ESP(ESP Protocol) Planning(Internal IPSECPROPOSAL
planning)
MD5, SHA1, AES- Transport
XCBC-MAC-96, SHA1(SHA1) SHA1(SHA1) Planning(Internal IPSECPROPOSAL
SHA256 planning)
NULL, MD5, SHA1, Transport

AES-XCBC-MAC- SHA1(SHA1) SHA1(SHA1) Planning(Internal IPSECPROPOSAL
96, SHA256 planning)
NULL, DES, 3DES, Transport
AES128, AES192, AES128(AES128) AES128(AES128) Planning(Internal IPSECPROPOSAL
AES256 planning)
0~7 0 None N/A IPSECPROPOSAL
DISABLE, ENABLE None None N/A LOCALETHPORT
UP, DOWN None None N/A LOCALETHPORT
0~4294967295 None None N/A LOCALETHPORT

Planned IP address
Transport
for local
Valid IP address 192.168.0.49 Planning(Internal LOCALIP
maintenance on a
planning)
board
Planned subnet
Transport
mask of the local
Valid Mask address 255.255.255.0 Planning(Internal LOCALIP
maintenance
planning)
channel on a board
Transport
FE80:0:0:0:2315:E6
Valid IP address None Planning(Internal LOCALIP6
2F:526:4623
planning)
Transport
1~128 64 None Planning(Internal LOCALIP6
planning)
IP6_DAD_OK,
IP6_DAD_TENTATI
VE,
IP6_DAD_DUPLIC None None N/A LOCALIP6
ATED,
IP6_DAD_UNKNO
W
0~4294967295 None None N/A LOCALIP6
0~4294967295 None None N/A LOCALIP6

Default/Recommen
0~7 0 0 LR
ded Value
Default/Recommen
0~1 0 0 LR
ded Value
Transport
0~7 None None Planning(Internal LR
planning)
Transport
MPGRP, ETH,
None None Planning(Internal LR
ETHTRK, TUNNEL
planning)
Transport
planning)
Transport
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Planning(Internal LR
planning)
Transport
planning)
Transport
planning)
Transport
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal LR
D
The recommended
value for this
parameter is 31744
if PT is set to Transport
32~1000000 None MPGRP. Planning(Internal LR
The recommended planning)
value is 540000 if
PT is set to ETH or
ETHTRK.
Default/Recommen
0~7 0 0 MPGRP
ded Value
Default/Recommen
0~1 0 0 MPGRP
ded Value
Transport
0~7 None None Planning(Internal MPGRP
planning)
Transport
0~3 None None Planning(Internal MPGRP
planning)
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) MPGRP
ded Value
NONAUTH, PAP, PAP(PAP PAP(PAP Default/Recommen

MPGRP
CHAP Authentication) Authentication) ded Value
Transport
1~67 characters None None Planning(Internal MPGRP
planning)
Transport
1~19 characters None None Planning(Internal MPGRP
planning)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio MPGRP
n with the peer)
Transport
Valid Mask address 0.0.0.0 None Planning(Negotiatio MPGRP
n with the peer)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio MPGRP
n with the peer)
Default/Recommen
LONG, SHORT LONG(Long) LONG(Long) MPGRP
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) MPGRP
ded Value
Default/Recommen
128~1500 256 256 MPGRP
ded Value
Default/Recommen
1~512 192 192 MPGRP
ded Value
Default/Recommen
3~1500 1500 1500 MPGRP
ded Value
Default/Recommen
1~1000 10 10 MPGRP
ded Value
Default/Recommen
4,8 8 None MPGRP
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) MPGRP
ded Value
Default/Recommen
0~1000 100 100 MPGRP
ded Value
Default/Recommen
0~1000 50 50 MPGRP
ded Value
UP, DOWN None None N/A MPGRP

INITIAL,
STARTING,
CLOSED,
STOPPED,
CLOSING,
None None N/A MPGRP
STOPPING,
REQSENT,
ACKRCVD,
ACKSENT,
OPENED
INITIAL,
STARTING,
CLOSED,
STOPPED,
CLOSING,
None None N/A MPGRP
STOPPING,
REQSENT,
ACKRCVD,
ACKSENT,
OPENED
Valid IP address None None N/A MPGRP
DISABLE, ENABLE None None N/A MPGRP
128~1500 None None N/A MPGRP

Transport
BASE_BOARD,
None None Planning(Internal MPGRP
E1_COVERBOARD
planning)

Default/Recommen
0~7 0 0 MPLNK
ded Value
Default/Recommen
0~1 0 0 MPLNK
ded Value
Transport
0~7 None None Planning(Internal MPLNK
planning)
Transport
0~15 0 0 Planning(Internal MPLNK
planning)
Default/Recommen
0~3 0 0 MPLNK
ded Value
Default/Recommen
0~1 0 0 MPLNK
ded Value
Transport
0~7 None None Planning(Internal MPLNK
planning)
Default/Recommen
0~7 0 0 MPLNK
ded Value
TS1, TS2, TS3,
TS4, TS5, TS6,
TS7, TS8, TS9,
TS10, TS11, TS12,
TS13, TS14, TS15, Transport
TS16, TS17, TS18, None None Planning(Internal MPLNK
TS19, TS20, TS21, planning)
TS22, TS23, TS24,
TS25, TS26, TS27,
TS28, TS29, TS30,
TS31
Default/Recommen
128~1500 1500 1500 MPLNK
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) MPLNK
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) MPLNK
ded Value
Default/Recommen
1~65535 3000 3000 MPLNK
ded Value
Transport
BASE_BOARD,
None None Planning(Internal MPLNK
E1_COVERBOARD
planning)
If SBT is set to
BASE_BOARD or
BACK_BOARD,
you are advised to
set MPGRPSBT to
BASE_BOARD.
BASE_BOARD, Default/Recommen
None If SBT is set to MPLNK
E1_COVERBOARD ded Value
E1_COVERBOARD
, you are advised to
set to MPGRPSBT
to
E1_COVERBOARD
.
UP, DOWN None None N/A MPLNK

INITIAL,
STARTING,
CLOSED,
STOPPED,
CLOSING,
None None N/A MPLNK
STOPPING,
REQSENT,
ACKRCVD,
ACKSENT,
OPENED
128~1500 None None N/A MPLNK
DISABLE, ENABLE None None N/A MPLNK
DISABLE, ENABLE None None N/A MPLNK
Transport
BASE_BOARD,
None None Planning(Internal MPLNK
E1_COVERBOARD
planning)

Transport
MASTER, SLAVE None None Planning(Internal OMCH
planning)
Transport
Valid IP address None None Planning(Negotiatio OMCH
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
Transport
n with the peer)
Default/Recommen
0~7 0 0 OMCH
ded Value
Default/Recommen
0~1 0 0 OMCH
ded Value
Transport
0~7 None None Planning(Internal OMCH
planning)
Transport
IPV4 IPV4(IPV4) None Planning(Internal OMCH
planning)
Transport
NO, YES NO(No) NO(No) Planning(Internal OMCH
planning)
Transport
n with the peer)
Transport
n with the peer)
Transport
NEXTHOP(Next
NEXTHOP, IF None Planning(Internal OMCH
Hop)
planning)
Transport
PPP, MPGRP,
None None Planning(Internal OMCH
TUNNEL
planning)
Transport
0~14 None None Planning(Internal OMCH
planning)
Transport
1~255 60 60 Planning(Internal OMCH
planning)
Transport
Valid IP address None None Planning(Internal OMCH
planning)
NORMAL,
ABNORMAL, None None N/A OMCH
UNKNOWN
INUSE, UNUSED None None N/A OMCH
BASE_BOARD,
Transport
BACK_BOARD,
None None Planning(Internal OMCH
ETH_COVERBOAR
planning)
D
Transport
Valid IP address None None Planning(Negotiatio OMCH6
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio OMCH6
n with the peer)
NORMAL,
ABNORMAL, None None N/A OMCH6
UNKNOWN
Default/Recommen
0~7 0 0 PACKETFILTER
ded Value
Default/Recommen
0~1 0 0 PACKETFILTER
ded Value
Transport
0~7 None None Planning(Internal PACKETFILTER
planning)
Transport
ETH, ETHTRK,
None None Planning(Internal PACKETFILTER
TUNNEL
planning)
Transport
planning)
Transport
planning)
Default/Recommen
PERMIT, DENY PERMIT(Permit) PERMIT(Permit) PACKETFILTER
ded Value
BASE_BOARD,
Transport
BACK_BOARD,
None None Planning(Internal PACKETFILTER
ETH_COVERBOAR
planning)
D
0~4294967295 None None N/A PACKETFILTER


Transport
planning)
ADV_ACL, Transport
ADV_ACL(Only
L2_ACL, None Planning(Internal PACKETFILTER
Advanced ACL)
ADV_AND_L2 planning)
Transport
Valid IP address None None Planning(Internal PINGFILTER
planning)
Transport
Valid Mask address None None Planning(Internal PINGFILTER
planning)
PASSIVE(Passive PASSIVE(Passive Default/Recommen

PASSIVE, ACTIVE PMTUCFG
Default/Recommen
49152~65535 52889 52889 PMTUCFG
ded Value
Default/Recommen
500~5000 5000 5000 PMTUCFG
ded Value
Default/Recommen
5~60,65535 65535 65535 PMTUCFG
ded Value
Default/Recommen
0~63 63 63 PMTUCFG
ded Value
Default/Recommen
0~7 0 0 PORTSECURITY
ded Value
Default/Recommen
0~1 0 0 PORTSECURITY
ded Value
Transport
0~7 None None Planning(Internal PORTSECURITY
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal PORTSECURITY
D
Transport
ETH, E1T1 ETH(Ethernet Port) ETH(Ethernet Port) Planning(Internal PORTSECURITY
planning)
Transport
0~7 None None Planning(Internal PORTSECURITY
planning)
Transport
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Planning(Internal PORTSECURITY
planning)
Default/Recommen
0~7 0 0 PPPLNK
ded Value
Default/Recommen
0~1 0 0 PPPLNK
ded Value
Transport
0~7 None None Planning(Internal PPPLNK
planning)
Transport
planning)
Transport
planning)
NONAUTH, PAP, PAP(PAP PAP(PAP Default/Recommen

PPPLNK
CHAP Authentication) Authentication) ded Value
Transport
1~67 characters None None Planning(Internal PPPLNK
planning)
Transport
1~19 characters None None Planning(Internal PPPLNK
planning)
TS1, TS2, TS3,

TS4, TS5, TS6,
TS7, TS8, TS9,
TS10, TS11, TS12,
TS13, TS14, TS15, Transport
TS16, TS17, TS18, None None Planning(Internal PPPLNK
TS19, TS20, TS21, planning)
TS22, TS23, TS24,
TS25, TS26, TS27,
TS28, TS29, TS30,
TS31
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio PPPLNK
n with the peer)
Transport
Valid Mask address 0.0.0.0 None Planning(Negotiatio PPPLNK
n with the peer)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio PPPLNK
n with the peer)
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) PPPLNK
ded Value
Default/Recommen
1~512 192 192 PPPLNK
ded Value
Default/Recommen
3~1500 1500 1500 PPPLNK
ded Value
Default/Recommen
1~1000 10 10 PPPLNK
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) PPPLNK
ded Value
Default/Recommen
128~1500 1500 1500 PPPLNK
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
1~65535 3000 3000 PPPLNK
ded Value
UP, DOWN None None N/A PPPLNK
INITIAL,
STARTING,
CLOSED,
STOPPED,
CLOSING,
None None N/A PPPLNK
STOPPING,
REQSENT,
ACKRCVD,
ACKSENT,
OPENED
INITIAL,
STARTING,
CLOSED,
STOPPED,
CLOSING,
STOPPING,
REQSENT,
ACKRCVD,
ACKSENT,
OPENED
INITIAL,
STARTING,
CLOSED,
STOPPED,
CLOSING,
STOPPING,
REQSENT,
ACKRCVD,
ACKSENT,
OPENED
Valid IP address None None N/A PPPLNK
DISABLE, ENABLE None None N/A PPPLNK
128~1500 None None N/A PPPLNK

Default/Recommen
1~1000 10 10 PPPLNK
ded Value
Default/Recommen
1~1000 6 6 PPPLNK
ded Value
Transport
BASE_BOARD,
None None Planning(Internal PPPLNK
E1_COVERBOARD
planning)

Default/Recommen
0~63 46 46 PRI2QUE
ded Value
Default/Recommen
0~63 34 34 PRI2QUE
ded Value
Default/Recommen
0~63 26 26 PRI2QUE
ded Value
Default/Recommen
0~63 18 18 PRI2QUE
ded Value
Default/Recommen
0~63 10 10 PRI2QUE
ded Value
Default/Recommen
0~63 0 0 PRI2QUE
ded Value
Default/Recommen
0~63 0 0 PRI2QUE
ded Value
Default/Recommen
0~7 0 0 RSCGRP
ded Value
Default/Recommen
0~1 0 0 RSCGRP
ded Value
Transport
0~7 None None Planning(Internal RSCGRP
planning)
Transport
IP None None Planning(Internal RSCGRP
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal RSCGRP
D
Transport
PPP, MPGRP, ETH,
None None Planning(Internal RSCGRP
ETHTRK, TUNNEL
planning)
Transport
0~15 0 0 Planning(Internal RSCGRP
planning)
0, 1, 2, 3, 4, 5, 6, 7,
Transport
8, 9, 10, 11, 12, 13,
None None Planning(Internal RSCGRP
14, 15,
planning)
DEFAULTPORT
Transport
KBPS KBPS(Kbit/s) None Planning(Internal RSCGRP
planning)
Transport
planning)
Transport
planning)
The recommended Transport
64~1000000 64 value is twice the Planning(Internal RSCGRP
TX bandwidth. planning)
The recommended Transport
64~1000000 64 value is twice the Planning(Internal RSCGRP
TX bandwidth. planning)
Transport
0~3 0 0 Planning(Internal RSCGRP
planning)
Default/Recommen
1~100 100 100 RSCGRP
ded Value
Transport
planning)
Transport
planning)
Transport
planning)
Transport
planning)
Transport
planning)
0~4294967295 None None N/A RSCGRP

SINGLE_RATE,
None None N/A RSCGRP
DUAL_RATE

0~4294967295 0 None N/A RSCGRP
Default/Recommen
0~7 0 0 RSCGRPALG
ded Value
Default/Recommen
0~1 0 0 RSCGRPALG
ded Value
Transport
0~7 None None Planning(Internal RSCGRPALG
planning)
BASE_BOARD,
, BACK_BOARD, None None Planning(Internal RSCGRPALG
D
Transport
PPP, MPGRP, ETH,
None None Planning(Internal RSCGRPALG
ETHTRK, TUNNEL
planning)
Transport
0~15 0 0 Planning(Internal RSCGRPALG
planning)
0, 1, 2, 3, 4, 5, 6, 7,
Transport
8, 9, 10, 11, 12, 13,
None None Planning(Internal RSCGRPALG
14, 15,
planning)
DEFAULTPORT
OFF, ON OFF(Off) OFF(Off) Engineering Design RSCGRPALG

0~1000 30 30 Engineering Design RSCGRPALG


DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Engineering Design RSCGRPALG

DISABLE, ENABLE DISABLE(Disable) DISABLE(Disable) Engineering Design RSCGRPALG



Transport
0~79 None None Planning(Internal SCTPLNK
planning)
Default/Recommen
0~7 0 0 SCTPLNK
ded Value
Default/Recommen
0~1 0 0 SCTPLNK
ded Value
Transport
0~7 None None Planning(Internal SCTPLNK
planning)
Default/Recommen
1~34 17 17 SCTPLNK
ded Value
Transport
Valid IP address None None Planning(Negotiatio SCTPLNK
n with the peer)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio SCTPLNK
n with the peer)
Transport
1024~65535 None None Planning(Negotiatio SCTPLNK
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio SCTPLNK
n with the peer)
Transport
Valid IP address 0.0.0.0 None Planning(Negotiatio SCTPLNK
n with the peer)
Transport
1024~65535 None None Planning(Negotiatio SCTPLNK
n with the peer)
Default/Recommen
10~59999 1000 1000 SCTPLNK
ded Value
Default/Recommen
11~60000 3000 3000 SCTPLNK
ded Value
Default/Recommen
10~59999 1000 1000 SCTPLNK
ded Value
12 12 SCTPLNK
step:0.01 ded Value
25 25 SCTPLNK
step:0.01 ded Value
Default/Recommen
1000~60000 5000 5000 SCTPLNK
ded Value
Default/Recommen
2~254 10 10 SCTPLNK
ded Value
Default/Recommen
1~253 5 5 SCTPLNK
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) None SCTPLNK
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) None SCTPLNK
ded Value
Default/Recommen
ALDER32, CRC32 CRC32(CRC32) None SCTPLNK
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) SCTPLNK
ded Value
Default/Recommen
1~254 10 10 SCTPLNK
ded Value
SCTP_STAT_DOW
N,
SCTP_STAT_CON None None N/A SCTPLNK
GESTION,
SCTP_STAT_UP
SCTP_TRANSFER
_CAUSE_START,
SCTP_TRANSFER
_CAUSE_LINKDO
WN,
SCTP_TRANSFER
_CAUSE_PORTDI
SABLED,
SCTP_TRANSFER
_CAUSE_INIT, None None N/A SCTPLNK
SCTP_TRANSFER
_CAUSE_UNKNO
WERROR,
SCTP_TRANSFER
_CAUSE_NORMAL
,
SCTP_TRANSFER
_CAUSE_USERDE
LETE
None None None N/A SCTPLNK
0~34 None None N/A SCTPLNK
0~34 None None N/A SCTPLNK
ACTIVE, STANDBY None None N/A SCTPLNK
UNBLOCK(Unblock UNBLOCK(Unblock Default/Recommen

UNBLOCK, BLOCK SCTPLNK
) ) ded Value
Default/Recommen
10~500 200 200 SCTPLNK
ded Value
Default/Recommen
0~47 characters NULL None SCTPLNK
ded Value
Transport
0~79 None None Planning(Internal SCTPLNK6
planning)
Default/Recommen
1~34 17 17 SCTPLNK6
ded Value
Transport
Valid IP address None None Planning(Negotiatio SCTPLNK6
n with the peer)
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Negotiatio SCTPLNK6
n with the peer)
Transport
1024~65535 None None Planning(Negotiatio SCTPLNK6
n with the peer)
Transport
Valid IP address None None Planning(Negotiatio SCTPLNK6
n with the peer)
Transport
Valid IP address 0:0:0:0:0:0:0:0 None Planning(Negotiatio SCTPLNK6
n with the peer)
Transport
1024~65535 None None Planning(Negotiatio SCTPLNK6
n with the peer)
Default/Recommen
1000~60000 1000 1000 SCTPLNK6
ded Value
Default/Recommen
1000~60000 3000 3000 SCTPLNK6
ded Value
Default/Recommen
1000~60000 1000 1000 SCTPLNK6
ded Value
12 12 SCTPLNK6
step:0.01 ded Value
25 25 SCTPLNK6
step:0.01 ded Value
Default/Recommen
1000~60000 5000 5000 SCTPLNK6
ded Value
Default/Recommen
2~254 10 10 SCTPLNK6
ded Value
Default/Recommen
1~253 5 5 SCTPLNK6
ded Value
Default/Recommen
ALDER32, CRC32 CRC32(CRC32) None SCTPLNK6
ded Value
Default/Recommen
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) SCTPLNK6
ded Value
Default/Recommen
1~254 10 10 SCTPLNK6
ded Value
SCTP_STAT_DOW
N,
SCTP_STAT_CON None None N/A SCTPLNK6
GESTION,
SCTP_STAT_UP
SCTP_TRANSFER
_CAUSE_START,
SCTP_TRANSFER
_CAUSE_LINKDO
WN,
SCTP_TRANSFER
_CAUSE_PORTDI
SABLED,
SCTP_TRANSFER
_CAUSE_INIT, None None N/A SCTPLNK6
SCTP_TRANSFER
_CAUSE_UNKNO
WERROR,
SCTP_TRANSFER
_CAUSE_NORMAL
,
SCTP_TRANSFER
_CAUSE_USERDE
LETE
None None None N/A SCTPLNK6
0~34 None None N/A SCTPLNK6
0~34 None None N/A SCTPLNK6
ACTIVE, STANDBY None None N/A SCTPLNK6
UNBLOCK(Unblock UNBLOCK(Unblock Default/Recommen

UNBLOCK, BLOCK SCTPLNK6
) ) ded Value
Transport
0~47 characters NULL None Planning(Internal SCTPLNK6
planning)
Transport
Valid IP address None None Planning(Internal SUBNETVLAN
planning)
Transport
Valid Mask address None 255.255.255.255 Planning(Internal SUBNETVLAN
planning)
Transport
1~4094 None None Planning(Internal SUBNETVLAN
planning)
Default/Recommen
OFF, ON ON(On) ON(On) TACALG
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 100 100 TACALG
ded Value
Default/Recommen
0~100 100 100 TACALG
ded Value
Default/Recommen
0~100 100 100 TACALG
ded Value
Default/Recommen
0~100 100 100 TACALG
ded Value
Default/Recommen
0~100 0 0 TACALG
ded Value
Default/Recommen
0~100 0 0 TACALG
ded Value
Default/Recommen
0~100 0 0 TACALG
ded Value
Default/Recommen
0~100 0 0 TACALG
ded Value
Default/Recommen
0~100 0 0 TACALG
ded Value
Default/Recommen
0~100 90 90 TACALG
ded Value
Default/Recommen
0~100 90 90 TACALG
ded Value
Default/Recommen
0~100 85 85 TACALG
ded Value
Default/Recommen
0~100 85 85 TACALG
ded Value
Default/Recommen
0~100 85 85 TACALG
ded Value
Default/Recommen
0~100 85 85 TACALG
ded Value
Default/Recommen
0~100 85 85 TACALG
ded Value
Default/Recommen
0~100 85 85 TACALG
ded Value
Default/Recommen
0~100 100 100 TACALG
ded Value
Default/Recommen
0~100 100 100 TACALG
ded Value
Default/Recommen
OFF, ON OFF(Off) OFF(Off) TACALG
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
ded Value
Default/Recommen
0~100 70 70 TLDRALG
ded Value
Default/Recommen
0~100 70 70 TLDRALG
ded Value
Default/Recommen
0~100 65 65 TLDRALG
ded Value
Default/Recommen
0~100 65 65 TLDRALG
ded Value
Default/Recommen
0~100 50 50 TLDRALG
ded Value
Default/Recommen
0~100 50 50 TLDRALG
ded Value
Default/Recommen
0~100 45 45 TLDRALG
ded Value
Default/Recommen
0~100 45 45 TLDRALG
ded Value
Transport
DISABLE, ENABLE ENABLE(Enable) ENABLE(Enable) Planning(Internal TLFRSWITCH
planning)
Default/Recommen
OFF, ON ON(On) ON(On) TOLCALG
ded Value
Default/Recommen
OFF, ON ON(On) ON(On) TOLCALG
ded Value
Default/Recommen
0~100 95 95 TOLCALG
ded Value
Default/Recommen
0~100 90 90 TOLCALG
ded Value
Default/Recommen
0~100 5 5 TOLCALG
ded Value
Default/Recommen
0~100 95 95 TOLCALG
ded Value
Default/Recommen
0~100 90 90 TOLCALG
ded Value
Transport
WHITELIST, WHITELIST(Whiteli WHITELIST(Whiteli
Planning(Internal TRANSPORT
BLACKLIST st) st)
planning)
0~4294967295 None None N/A TRANSPORT



Transport
0~7 0 None Planning(Internal TUNNEL
planning)
Transport
0~1 0 None Planning(Internal TUNNEL
planning)
Transport
0~7 None None Planning(Internal TUNNEL
planning)
Transport
planning)
Transport
planning)
Transport
planning)
Transport
planning)
0~4294967295 None None N/A TUNNEL

Transport
0~3 None None Planning(Internal VLANCLASS
planning)
USERDATA, SIG,
Transport
OTHER,
None None Planning(Internal VLANCLASS
OM_HIGH,
planning)
OM_LOW
It is recommended
that the value of
this parameter be Transport
0~63 0 consistent with the Planning(Internal VLANCLASS
implementation of planning)
the differentiated
service.
Transport
1~4094 None None Planning(Internal VLANCLASS
planning)
Transport
0~7 0 0 Planning(Internal VLANCLASS
planning)
Transport
Valid IP address None None Planning(Internal VLANMAP
planning)
Transport
Valid Mask address 255.255.255.255 None Planning(Internal VLANMAP
planning)
Transport
SINGLEVLAN,
None None Planning(Internal VLANMAP
VLANGROUP
planning)
Transport
1~4094 None None Planning(Internal VLANMAP
planning)
Transport
0~7 0 0 Planning(Internal VLANMAP
planning)
Transport
0~3 None None Planning(Internal VLANMAP
planning)
Transport
DISABLE, ENABLE ENABLE(Enable) DISABLE(Disable) Planning(Internal VLANMAP
planning)
Default/Recommen
5000~60000 5000 5000 GTPU
ded Value
Default/Recommen
3~6 3 3 GTPU
ded Value
Default/Recommen
0~63 63 63 GTPU
ded Value
Default/Recommen
DISABLE, ENABLE DISABLE(Disable) None GTPU
ded Value
Service
Parameter Interruption
Access Interrupted After Interruption Scope
Relationship Duration (min)
Modification
None Read Only N/A N/A N/A
No (And no impact
None Read & Write on the UE in idle N/A N/A
mode)
No (And no impact
mode)
No (And no impact
mode)
None Read & Write Yes Cells <1
The parameter is
used only when the No (And no impact
PROTOCOL Read & Write on the UE in idle N/A N/A
parameter is set to mode)
TDL_IR.



If some cells of an
eNodeB are
neighboring cells of
each other, the
neighbor
relationships with
these cells must be
removed manually
before the Read & Write Yes eNodeB <3
eNodeB is
modified. The
eNodeB must be
reset after the
modification so that
the parameter can
take effect.
slashes (/),
backslashes(\),
pipes (|), double
quotation marks ("),
commas (,),
semicolons (;),
equal signs (=),
single quotation
marks ('), three plus
signs (+++), two or
more consecutive
spaces, and two or
more consecutive
percentage signs
(%).
Due to the
limitations defined
in the S1 interface No (And no impact
protocol (For Read & Write on the UE in idle N/A N/A
details, see 3GPP mode)
TS 36.413), the
value of NAME can
contain only the
following valid
characters: upper-
case letters (A to Z),
lower-case letters
(a to z), digits (0 to
9), single blank ( ),
apostrophe ('), left
brackets ((), right
brackets ()), one or
two plus sign (+),
hyphens (-), full
stops (.), and
American Standard
Code for
None Read & Write Yes eNodeB <3
When the automatic

power control
the services of a
None Read & Write Yes eNodeB cell are interrupted
from the automatic
power-off time to
the next automatic
power-on time.
POWERONTIME When the automatic

must be an hour power control
later than switch is turned on,
POWEROFFTIME. the services of a
POWEROFFTIME Read & Write Yes eNodeB cell are interrupted
must range from from the automatic
22:00:00 to power-off time to
05:00:00 of the next the next automatic
day. power-on time.
POWERONTIME
must range from
23:00:00 to
06:00:00 of the next No (And no impact
day. Read & Write on the UE in idle N/A N/A
POWERONTIME mode)
must be an hour
later than
POWEROFFTIME.
LONGITUDE is
No (And no impact
valid only when
Read & Write on the UE in idle N/A N/A
GCDF is set to
mode)
DEG.
LATITUDE is valid No (And no impact
only when GCDF is Read & Write on the UE in idle N/A N/A
set to DEG. mode)

No (And no impact
mode)
LONGITUDE and
LATITUDE are valid
only when this
GCDF is set to
DEG.
No (And no impact
LONGITUDESECF
ORMAT and
mode)
LONGITUDESECF
ORMAT are valid
only when this
GCDF is set to
SEC.
LATITUDESECFO
RMAT is valid and
must be specified if
GCDF is set to
SEC.
If GCDF is set to
SEC, this
LATITUDESECFO
RMAT must be
specified in the
format of
dd:mm:ss.ssss. dd
No (And no impact
indicates the
degree ranging
mode)
from -90 to +90,
mm indicates the
minute ranging from
0 to 59, and ss.ssss
indicates the
second ranging
from 0 to 59.9999.
The value range of
this parameter is
from
-90:00:00.0000 to
+90:00:00.0000.
LONGITUDESECF
ORMAT is valid and
must be specified if
GCDF is set to
SEC.
If GCDF is set to
SEC, this
LONGITUDESECF
ORMAT must be
specified in the
format of
ddd:mm:ss.ssss.
No (And no impact
ddd indicates the
degree ranging
mode)
from -180 to +180,
mm indicates the
minute ranging from
indicates the
second ranging
from 0 to 59.9999.
The value range of
this parameter is
from
-180:00:00.0000 to
+180:00:00.0000.
None Read & Write Yes eNodeB <3

No (And no impact
mode)
percentages.
If KPITYPE is set to
Cell_Call_Drop_Rat
e, the threshold is
set to a value in the
range of 0 to 100 in
percentages.
Intra-
Frequency_HO_Su
cc_Rate, the
threshold is set to a
value in the range
of 0 to 100 in
percentages.
Inter-
Frequency_HO_Su
No (And no impact
cc_Rate, the
mode)
value in the range
of 0 to 100 in
percentages.
LTE-
CDMA_Handover_
Succ_Rate, the
value in the range
of 0 to 100 in
percentages.
LTE-
WCDMA_Handover
_Succ_Rate, the
value in the range
of 0 to 100 in
percentages.
Cell_Call_Drop_Rat
e, the threshold is
set to a value in the
range of 0 to 100 in
percentages.
Intra-
Frequency_HO_Su
cc_Rate, the
value in the range
of 0 to 100 in
percentages.
Inter-
Frequency_HO_Su
No (And no impact
cc_Rate, the
mode)
value in the range
of 0 to 100 in
percentages.
LTE-
CDMA_Handover_
Succ_Rate, the
value in the range
of 0 to 100 in
percentages.
LTE-
WCDMA_Handover
_Succ_Rate, the
value in the range
of 0 to 100 in
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

This LATITUDE is
No (And no impact
valid only when
GCDF is set to
mode)
DEG.
This LONGITUDE
No (And no impact
is valid only when
GCDF is set to
mode)
DEG.
R0F, and R0H

ports; R0C, R0D,
R0G, and R0H
ports. the RRUs
where the antenna
ports are located
must have the
same cabinet
numbers, subrack
numbers, and slot
numbers.
The antenna ports
used by a
consolidation sector
must be located on
two RRUs or RFUs.
In TDD mode, when
a normal MIMO
sector is used, Read & Write Yes Cells 1
2T2R sectors are
set up on the RRUs
with four TX
channels and four
RX channels, and
the channels must
be in the different
polarization
direction. That is,
the antenna ports
used by the sectors
in this case must be
one of the following
combinations: R0A
and R0B ports;
R0C and R0D
ports. Meanwhile,
the RRUs where
sector is a
consolidation
sector.
In TDD mode, only
2T2R supports
consolidation
sectors. In FDD
mode, only 2T2R,
2T4R, or 4T4R
supports
consolidation
sectors.
The consolidated
RRUs or RFUs
must be set up on
the first level of two
chains on an LBBP,
namely that PS or
PS must be set to 0 Read & Write Yes Cells 1
and AT must be set
to LOCALPORT.
When the SECM is
set to mutual-aid
MIMO, the ANTM
must be set to
2T2R.
When the SECM is
set to mutual-aid
MIMO, All RRU or
RFU MOs that
correspond the
AntennaPort MOs
used by the Sector
MOs are on the
single-level of a
chain, namely that
PS in the RRU or
by a sector in two-
RRU combination
mode, and antenna
ports on three
RRUs are used by
a sector in three-
RRU combination
mode.
In multi-RRU
combination mode,
multiple RRUs can
be combined to
form a cell. The
transmitter
transmits the
downlink signals of
the cell on each
RRU. The receiver No (And no impact
combines the uplink Read & Write on the UE in idle N/A N/A
signals of the cell mode)
from multiple RRUs
or selectively
demodulates them.
Multi-RRU
combination can
increase cell
coverage radius
and reduce UE
handovers.
However, it also
reduces network
capacity.
If a sector is a
normal MIMO
sector, the
combination mode
of the sector is not






No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
LONGITUDE and
LATITUDE are valid
only when this
GCDF is set to
DEG.
No (And no impact
ANTLATITUDESEC
FORMAT and
mode)
ANTLONGITUDES
ECFORMAT are
valid only when this
GCDF is set to
SEC.
This
ANTLATITUDESEC
FORMAT must be
specified if GCDF is
set to SEC.
If GCDF is set to
SEC, this
ANTLATITUDESEC
FORMAT must be
specified in the
format of
dd:mm:ss.ssss. dd
No (And no impact
indicates the
degree ranging
mode)
from -90 to +90,
mm indicates the
minute ranging from
indicates the
second ranging
from 0 to 59.9999.
The value range of
this parameter is
from
-90:00:00.0000 to
+90:00:00.0000.
This
ANTLONGITUDES
ECFORMAT must
be specified if
GCDF is set to
SEC.
If GCDF is set to
SEC, this
ANTLONGITUDES
ECFORMAT must
be specified in the
format of
ddd:mm:ss.ssss. No (And no impact
ddd indicates the Read & Write on the UE in idle N/A N/A
degree ranging mode)
from -180 to +180,
mm indicates the
minute ranging from
indicates the
second ranging
from 0 to 59.9999.
The value range of
this parameter is
from
-180:00:00.0000 to
+180:00:00.0000.
No (And no impact
mode)




No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
When CTRLCN in
the ALD MO is set
to 0, the value
range of CTRLSRN
is 4 to 5, or 60 to No (And no impact
254. When the Read & Write on the UE in idle N/A N/A
value range of mode)
CTRLCN in the
ALD MO is 1 to 62,
CTRLSRN is set to
4 or 5.
When CTRLSRN in
the ALD MO is set
to 4 or 5, the value
of CTRLSN ranges
from 0 to 8 if TYPE
in the Cabinet MO
where the ALD MO
is located is set to
No (And no impact
BTS3900AL. The
value of CTRLSN
mode)
ranges from 0 to 5 if
TYPE is not set to
BTS3900AL. When
the value of
CTRLSRN in the
ALD MO ranges
from 60 to 254,
CTRLSN is set to 0.
No (And no impact
mode)
No (And no impact
mode)

When CN in the
AntennaPort MO is
set to 0, the value
range of SRN is 4
to 5 or 60 to 254.
When the value of
Read Only N/A N/A N/A
CN in the
AntennaPort MO
ranges from 1 to
62, the value of
SRN is set to 4 or
5.
When SRN in the

AntennaPort MO is
set to 4 or 5, the
value of SN ranges
from 0 to 8 if TYPE
of the Cabinet MO
where the
AntennaPort MO is
located is set to
BTS3900AL. The
value of CTRLSN
TYPE is not set to
BTS3900AL. When
the value of SRN in
the AntennaPort
MO ranges from 60
to 254, SN is set 0.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the same RRU

MO, PWRSWITCH
in the RetPort MO No (And no impact
and PWRSWITCH Read & Write on the UE in idle N/A N/A
in the AntennaPort mode)
cannot be set to ON
at the same time.
No (And no impact
mode)
In an AntennaPort
MO, if
PWRSWITCH is set No (And no impact
to ON, the value of Read & Write on the UE in idle N/A N/A
UOTHD must be mode)
smaller than
UCTHD.
In an AntennaPort
MO, if
PWRSWITCH is set
to ON, the value of
UOTHD must be
smaller than
No (And no impact
UCTHD.
In an AntennaPort
mode)
MO, if
PWRSWITCH is set
to ON, the value of
UCTHD must be
smaller than
OCTHD.
In an AntennaPort
MO, if
PWRSWITCH is set No (And no impact
to ON, the value of Read & Write on the UE in idle N/A N/A
OCTHD must be mode)
smaller than
OOTHD.
In an AntennaPort
MO, if
PWRSWITCH is set
to ON, the value of
OCTHD must be
smaller than
No (And no impact
OOTHD.
In an AntennaPort
mode)
MO, if
PWRSWITCH is set
to ON, the value of
UCTHD must be
smaller than
OCTHD.
No (And no impact
mode)
When
POLARTYPE and
RETTYPE in a RET
are set to SINGLE
and SINGLE_RET, No (And no impact
respectively, only Read & Write on the UE in idle N/A N/A
one of CONNCN1 mode)
and CONNCN2 in
the RETSubunit
MO needs to be
configured.
The SCENARIO
should be
configured on the
basis of actual
physical connection
and meet the
following
conditions: 1. When
SCENARIO is set
No (And no impact
to REGULAR, one
RRU can control
mode)
one RET; 2. When
SCENARIO is set
to DAISY_CHAIN or
SECTOR_SPLITTI
NG or
2G_EXTENSION,
one RRU can
control more than
one RET.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
When CTRLCN in
the ALD MO is set
to 0, the value
range of CTRLSRN
CTRLCN in the
ALD MO is 1 to 62,
CTRLSRN is set to
4 or 5.
When CTRLSRN in
the ALD MO is set
of CTRLSN ranges
from 0 to 8 if TYPE
in the Cabinet MO
where the ALD MO
No (And no impact
BTS3900AL. The
value of CTRLSN
mode)
TYPE is not set to
BTS3900AL. When
the value of
CTRLSRN in the
ALD MO ranges
from 60 to 254,
CTRLSN is set to 0.
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED, BAND2 No (And no impact
cannot be set to Read & Write on the UE in idle N/A N/A
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
RetDeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
No (And no impact
mode)
No (And no impact
mode)



In the same RRU

MO, PWRSWITCH
in the RetPort MO No (And no impact
and PWRSWITCH Read & Write on the UE in idle N/A N/A
in the AntennaPort mode)
cannot be set to ON
at the same time.
No (And no impact
mode)
In a RetPort MO, if
PWRSWITCH is set
No (And no impact
to ON, the value of
UOTHD must be
mode)
smaller than
UCTHD.
In a RetPort MO, if
PWRSWITCH is set
to ON, the value of
UOTHD must be
smaller than
No (And no impact
UCTHD.
In a RetPort MO, if
mode)
PWRSWITCH is set
to ON, the value of
UCTHD must be
smaller than
OCTHD.
In a RetPort MO, if
PWRSWITCH is set
No (And no impact
to ON, the value of
OCTHD must be
mode)
smaller than the
value of OOTHD.
In a RetPort MO, if
PWRSWITCH is set
to ON, the value of
OCTHD must be
smaller than the
No (And no impact
value of OOTHD.
In a RetPort MO, if
mode)
PWRSWITCH is set
to ON, the value of
UCTHD must be
smaller than
OCTHD.

Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
When CONNCN1 in
a RETSubunit MO
is set to a value
other than 255,
CONNSRN1 and
CONNSN1 must all
be set to a value
other than 255.
Similarly, when
CONNCN2 in a
RETSubunit MO is
set to a value other No (And no impact
than 255, Read & Write on the UE in idle N/A N/A
CONNSRN2 and mode)
CONNSN2 must all
be set to a value
other than 255.
In a RETSubunit
MO, the
combination of
CONNCN1,
CONNSRN1,
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
When CONNCN1 in
a RETSubunit MO
is set to a value
other than 255,
CONNSRN1 and
CONNSN1 must all
be set to a value
other than 255.
Similarly, when
CONNCN2 in a
RETSubunit MO is
CONNSRN2 and mode)
CONNSN2 must all
be set to a value
other than 255.
In a RETSubunit
MO, the
combination of
CONNCN1,
CONNSRN1,
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
When CONNCN1 in
a RETSubunit MO
is set to a value
other than 255,
CONNSRN1 and
CONNSN1 must all
be set to a value
other than 255.
Similarly, when
CONNCN2 in a
RETSubunit MO is
CONNSRN2 and mode)
CONNSN2 must all
be set to a value
other than 255.
In a RETSubunit
MO, the
combination of
CONNCN1,
CONNSRN1,
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
In a RETSubunit
MO, the
combination of
No (And no impact
CONNCN1,
CONNSRN1,
mode)
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
When CONNCN1 in
a RETSubunit MO
is set to a value
other than 255,
CONNSRN1 and
CONNSN1 must all
be set to a value
other than 255.
Similarly, when
CONNCN2 in a
RETSubunit MO is
CONNSRN2 and mode)
CONNSN2 must all
be set to a value
other than 255.
In a RETSubunit
MO, the
combination of
CONNCN1,
CONNSRN1,
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
When CONNCN1 in
a RETSubunit MO
is set to a value
other than 255,
CONNSRN1 and
CONNSN1 must all
be set to a value
other than 255.
Similarly, when
CONNCN2 in a
RETSubunit MO is
CONNSRN2 and mode)
CONNSN2 must all
be set to a value
other than 255.
In a RETSubunit
MO, the
combination of
CONNCN1,
CONNSRN1,
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
When CONNCN1 in
a RETSubunit MO
is set to a value
other than 255,
CONNSRN1 and
CONNSN1 must all
be set to a value
other than 255.
Similarly, when
CONNCN2 in a
RETSubunit MO is
CONNSRN2 and mode)
CONNSN2 must all
be set to a value
other than 255.
In a RETSubunit
MO, the
combination of
CONNCN1,
CONNSRN1,
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
Only one
RETSubunit MO
can be configured
on an AntennaPort
MO.
In a RETSubunit
MO, the
combination of
No (And no impact
CONNCN1,
CONNSRN1,
mode)
CONNSN1, and
CONNPN1 cannot
be the same as the
combination of
CONNCN2,
CONNSRN2,
CONNSN2, and
CONNPN2.
No (And no impact
mode)
No (And no impact
mode)
The value of
No (And no impact
SUBNAME must be
unique in
mode)
RETSubunit MOs.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
When CTRLCN in
the ALD MO is set
to 0, the value
range of CTRLSRN
CTRLCN in the
ALD MO is 1 to 62,
CTRLSRN is set to
4 or 5.
When CTRLSRN in
the ALD MO is set
of CTRLSN ranges
from 0 to 8 if TYPE
in the Cabinet MO
where the ALD MO
No (And no impact
BTS3900AL. The
value of CTRLSN
mode)
TYPE is not set to
BTS3900AL. When
the value of
CTRLSRN in the
ALD MO ranges
from 60 to 254,
CTRLSN is set to 0.
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
MO, if BAND1 is
not set to UNUSED,
BAND1 cannot be
the same as
BAND2, BAND3, or
BAND4. The same
rule applies to
BAND2, BAND3,
and BAND4.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND3
cannot be set to
UNUSED. When
BAND3 is not set to
UNUSED. When mode)
BAND2 is not set to
UNUSED, BAND1
cannot be set to
UNUSED.
In a
TMADeviceData
MO, when BAND4
is not set to
UNUSED, BAND4
must be greater
than BAND3. When
BAND3 is not set to
UNUSED, BAND3
must be greater
than BAND2. When
BAND2 is not set to
UNUSED, BAND2
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

The four frequency

bands supported by
the TMA must differ
from each other.
The four frequency

bands supported by
the TMA must differ
from each other.
The four frequency

bands supported by
the TMA must differ
from each other.
The four frequency
bands supported by
the TMA must differ
from each other.

If RXMINFB or
RXMAXFB in the
TMADeviceData
MO is set, Read Only N/A N/A N/A
RXMINFB must be
smaller than
RXMAXFB.
If TXMINFB or
TXMAXFB in the
TMADeviceData
TXMINFB must be
smaller than
TXMAXFB.
If TXMINFB or
TXMAXFB in the
TMADeviceData
TXMINFB must be
smaller than
TXMAXFB.
If RXMINFB or
RXMAXFB in the
TMADeviceData
RXMINFB must be
smaller than
RXMAXFB.

In a TMASubunit
MO, a unique
combination of
No (And no impact
CONNCN,
CONNSRN,
mode)
CONNSN, and
CONNPN is
necessary.
In a TMASubunit
MO, a unique
combination of
No (And no impact
CONNCN,
CONNSRN,
mode)
CONNSN, and
CONNPN is
necessary.
In a TMASubunit
MO, a unique
combination of
No (And no impact
CONNCN,
CONNSRN,
mode)
CONNSN, and
CONNPN is
necessary.
In a TMASubunit
MO, a unique
combination of
No (And no impact
CONNCN,
CONNSRN,
mode)
CONNSN, and
CONNPN is
necessary.
No (And no impact
mode)
No (And no impact
mode)

The following
parameters cannot
be set to the same
value:
No (And no impact
DEVICENAME in
the RET MO,
mode)
DEVICENAME in
the TMA MO,and
DEVICENAME in
the VRET MO.
No (And no impact
mode)
If
CONNPN1,CONNP
N2,CONNPN3 and
CONNPN4 in a
VRETSubunit MO
are not set to No (And no impact
NULL, they must be Read & Write on the UE in idle N/A N/A
different. mode)
Only one
VRETSubunit MO
can be connected
to a VAntennaPort
MO.
If
CONNPN1,CONNP
N2,CONNPN3 and
CONNPN4 in a
VRETSubunit MO
different. mode)
Only one
VRETSubunit MO
can be connected
to a VAntennaPort
MO.
The value of
SUBNAME must be No (And no impact
unique in Read & Write on the UE in idle N/A N/A
VRETSubunit mode)
MOs.
No (And no impact
mode)

If
CONNPN1,CONNP
N2,CONNPN3 and
CONNPN4 in a
VRETSubunit MO
different. mode)
Only one
VRETSubunit MO
can be connected
to a VAntennaPort
MO.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If
CONNPN1,CONNP
N2,CONNPN3 and
CONNPN4 in a
VRETSubunit MO
different. mode)
Only one
VRETSubunit MO
can be connected
to a VAntennaPort
MO.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)



None Read & Write Yes BS Less than 3 minute
No (And no impact
mode)

No (And no impact
mode)


If MODE and
CLKSRC in the
Tasm MO are set to
MANUAL and TOD,
respectively, TYPE
of the
corresponding TOD Read & Write Yes BS Less than 3 minute
MO must be set to
IN.
In a TOD MO, when
SN is set to 6 or 7,
TYPE cannot be set
to OUT.
When two TOD

MOs have the value
6 or 7 for SN, SN in
one TOD MO must
be set to 6 and SN
in the other TOD
MO must be set to
7.
When SN in two
TOD MOs both are
greater than or
equal to 0 and
smaller than or
equal to 5, the Read & Write Yes BS Less than 3 minute
values of SN in the
two MOs must be
the same.
The values of SN in
two TOD MOs must
both be greater
than or equal to 0
and smaller than or
equal to 5, or
greater than or
equal to 6 and
smaller than or
equal to 7.
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
When a GPS MO is
configured on a
BBU subrack, GN Read Only N/A N/A N/A
must be set to 0 or
1.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)



No (And no impact
mode)
No (And no impact
mode)
The values of CNM

are both set to
L2_MULTICAST.
When two
IPCLKLNK MOs
are configured, the
combination of
ANNFREQ and
SYNCFREQ in the
two MOs must be
the same when the
are met: 1. The
values of ICPT are
both set to PTP; 2.
The values of CNM
are both set to
UNICAST; 3. The
values of Read & Write Yes BS Less than 3 minute
PROFILETYPE are
both set to
G.8265.1.
When two
IPCLKLNK MOs
are configured and
the values of ICPT
are both set to PTP,
the combination of
CN, SRN, SN,
CNM, DM, CMPST,
and DELAYTYPE
must be the same
in the two
IPCLKLNK MOs.
When two
IPCLKLNK MOs
are configured, the

not set to
L2_MULTICAST
and IPMODE is set
to IPV4.
When two
IPCLKLNK MOs
are configured, the
values of CIP in the
two MOs must be
the same when the
are met: 1. ICPT is
set to PTP and
CNM is not set to
L2_MULTICAST in
the two MOs; 2.
IPMODE is set to
IPV4 in the two
MOs.
Read & Write Yes BS Less than 3 minute
In the IPCLKLNK
MO, if CNM is not
set to
L2_MULTICAST
and IPMODE is set
to IPV4, CIP cannot
be set to 0.0.0.0,
255.255.255.255,
127.x.x.x, or 0.x.x.x,
and should be one
of CLASS A,
CLASS B, CLASS
C.
In the IPCLKLNK
MO, SIP and CIP
must be set to
different values
when CNM is not
set to
MO, SIP is valid
only when CNM is
not set to
L2_MULTICAST
and IPMODE is set
to IPV4.
In an IPCLKLNK
MO, SIP cannot be
set to 0.0.0.0,
255.255.255.255,
127.x.x.x, or 0.x.x.x,
and should be one
of CLASS A,
CLASS B, CLASS
C, when the
are met: 1. CNM is
not set to
L2_MULTICAST; 2. Read & Write Yes BS Less than 3 minute
IPMODE is set to
IPV4.
When two
IPCLKLNK MOs
are configured on
the same board, the
values of SIP in the
two MOs must be
different when the
are met: 1. ICPT is
set to PTP and
CNM is not set to
L2_MULTICAST
and IPMODE is set
to IPV4 in the two
MOs; 2. ICPT is set
to HW_DEFINED in
The DM is valid
only when ICPT in
the IPCLKLNK MO
is set to PTP.
When ICPT in the
IPCLKLNK MO is
set to
HW_DEFINED,
CMPST and
DELAYTYPE in the
No (And no impact
IPCLKLNK MO
cannot be
mode)
configured.
The DELAYTYPE is
valid only when
ICPT in the
IPCLKLNK MO is
set to PTP.
When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to OFF,
the BMC algorithm
is disabled, and the
settings of
CLASS0, CLASS1,
CLASS2, and
CLASS3 do not
take effect. When
CLASSIDENTIFY
in the IPCLKLNK No (And no impact
MO is set to ON, Read & Write on the UE in idle N/A N/A
the BMC algorithm mode)
is enabled. If there
are multiple clock
servers at different
clock quality levels,
the server that
meets the
customer's
requirements to the
most extent is
selected in
descending order of
priority.
When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to OFF,
the BMC algorithm
setting of CLASS0
does not take
effect. When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to ON,
the BMC algorithm
are multiple clock
No (And no impact
mode)
the server that
meets the
customer's
requirements to the
most extent is
selected in
descending order of
priority.
The values of any
two parameters
among CLASS0,
CLASS1, CLASS2,
and CLASS3 in an
IPCLKLNK must be
different.
When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to OFF,
the BMC algorithm
setting of CLASS1
does not take
effect. When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to ON,
the BMC algorithm
are multiple clock
No (And no impact
mode)
the server that
meets the
customer's
requirements to the
most extent is
selected in
descending order of
priority.
The values of any
two parameters
among CLASS0,
CLASS1, CLASS2,
and CLASS3 in an
IPCLKLNK must be
different.
When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to OFF,
the BMC algorithm
setting of CLASS2
does not take
effect. When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to ON,
the BMC algorithm
are multiple clock
No (And no impact
mode)
the server that
meets the
customer's
requirements to the
most extent is
selected in
descending order of
priority.
The values of any
two parameters
among CLASS0,
CLASS1, CLASS2,
and CLASS3 in an
IPCLKLNK must be
different.
When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to OFF,
the BMC algorithm
setting of CLASS3
does not take
effect. When
CLASSIDENTIFY
in the IPCLKLNK
MO is set to ON,
the BMC algorithm
are multiple clock
No (And no impact
mode)
the server that
meets the
customer's
requirements to the
most extent is
selected in
descending order of
priority.
The values of any
two parameters
among CLASS0,
CLASS1, CLASS2,
and CLASS3 in an
IPCLKLNK must be
different.
In the IPCLKLNK
MO, the
MACMODE is valid No (And no impact
only when ICPT is Read & Write on the UE in idle N/A N/A
set to PTP and mode)
CNM is set to
L2_MULTICAST.
In the IPCLKLNK
MO, the CLKMAC
is valid only when
No (And no impact
ICPT is set to PTP,
CNM is set to
mode)
L2_MULTICAST,
and MACMODE is
set to YES.
The CNM is valid

only when ICPT in
the IPCLKLNK MO
is set to PTP.
When ICPT in the

IPCLKLNK MO is
set to
HW_DEFINED,
CMPST and
DELAYTYPE in the No (And no impact
IPCLKLNK MO Read & Write on the UE in idle N/A N/A
cannot be mode)
configured.
The CMPST is valid
only when ICPT in
the IPCLKLNK MO
is set to PTP.

When two
IPCLKLNK MOs
are configured, the
No (And no impact
values of PRI must
be the same if the
mode)
values of ICPT are
both set to PTP in
the two MOs.
In the IPCLKLNK
MO, ANNFREQ is
valid only when No (And no impact
CNM is set to Read & Write on the UE in idle N/A N/A
UNICAST and mode)
PROFILETYPE is
set to G.8265.1.
In the IPCLKLNK
MO, SYNCFREQ is
UNICAST and mode)
PROFILETYPE is
set to G.8265.1.
In the IPCLKLNK
MO, MASTERPRIO
is valid only when No (And no impact
UNICAST and mode)
PROFILETYPE is
set to G.8265.1.
CNM is set to
UNICAST.
If PROFILETYPE in
the IPCLKLNK MO
is set to G.8265.1,
CLKSYNCMODE in
the Tasm MO must
be set to FREQ.
When two
IPCLKLNK MOs
are configured, the
values of
NEGDURATION in
the two MOs must
be the same when
the following
conditions are met:
1. The values of
No (And no impact
ICPT are both set
to PTP; 2. The
mode)
values of CNM are
both set to
UNICAST; 3. The
values of
PROFILETYPE are
both set to
G.8265.1.
When two
IPCLKLNK MOs
are configured, the
values of
PROFILETYPE in
the two MOs must
be the same when
the following
conditions are met:
1. The values of
ICPT are both set
NEGDURATION is
valid only when
CNM is set to
UNICAST and
PROFILETYPE is
set to G.8265.1.
When two
IPCLKLNK MOs
are configured, the
values of
NEGDURATION in
the two MOs must
be the same when
the following
conditions are met:
1. The values of
ICPT are both set
to PTP; 2. The
No (And no impact
values of CNM are
both set to
mode)
UNICAST; 3. The
values of
PROFILETYPE are
both set to
G.8265.1.
When two
IPCLKLNK MOs
are configured, the
values of
PROFILETYPE in
the two MOs must
be the same when
the following
conditions are met:
1. The values of
ICPT are both set
to PTP; 2. The
values of CNM are
If two IPCLKLNK
MOs are
configured, the two
MOs must have the
same IPMODE
value.
If IPMODE in the
IPCLKLNK MO is
set to IPV6,
CLKSYNCMODE in
the Tasm MO must
be set to FREQ.
In the IPCLKLNK
MO, CIPV6 is valid
only when CNM is
not set to
L2_MULTICAST
and IPMODE is set
to IPV6.
In the IPCLKLNK
MO, SIPV6 and
CIPV6 must be set
to different values
when ICPT is set to
PTP and CNM is
not set to
L2_MULTICAST
and IPMODE is set
to IPV6. Read & Write Yes BS Less than 3 minute
When two
IPCLKLNK MOs
are configured, the
values of CIPV6 in
the two MOs must
be the same when
the following
conditions are met:
1. ICPT is set to
PTP and CNM is
not set to
L2_MULTICAST in
the two MOs; 2.
IPMODE is set to
IPV6 in the two
MOs.
In the IPCLKLNK
MO, SIPV6 is valid
only when CNM is
not set to
L2_MULTICAST
and IPMODE is set
to IPV6.
When two
IPCLKLNK MOs
are configured on
the same board, the
values of SIPV6 in Read & Write Yes BS Less than 3 minute
the two MOs must
be different when
the following
conditions are met:
1. ICPT is set to
PTP and CNM is
not set to
L2_MULTICAST; 2.
IPMODE is set to
IPV6 in the two
MOs.
When a MPT MO is
configured in the
slot corresponding
to the SN in the
SyncEth MO, PN is
set to 0 or 1. When
a TRP MO is Read & Write Yes BS Less than 3 minute
configured in the
slot corresponding
to the SN in the
SyncEth, the value
of PN ranges from
0 to 5.
No (And no impact
mode)
No (And no impact
mode)

The SRCNO is valid

only when the clock
source specified by
the CLKSRC in the No (And no impact
Tasm MO supports Read & Write on the UE in idle N/A N/A
more than one mode)
clock link and the
value of MODE is
set to MANUAL.
The CLKSRC is
valid only when
MODE in the Tasm
MO is set to
MANUAL.
If MODE and
No (And no impact
CLKSRC in the
Tasm MO are set to
mode)
MANUAL and TOD,
respectively, TYPE
of the
corresponding TOD
MO must be set to
IN.
When MODE is set

to MANUAL and
CLKSRC is set to
SYNCETH+IPCLK
or GPS+SYNCETH,
the value of MODE
can be changed to
AUTO only in the
following methods:
1. Change the
value of MODE
from MANUAL to
FREE, and then to
No (And no impact
AUTO; 2. Change
the value of
mode)
CLKSRC to other
values, and then
change the value of
MODE to AUTO.
If MODE and
CLKSRC in the
Tasm MO are set to
MANUAL and TOD,
respectively, TYPE
of the
corresponding TOD
MO must be set to
IN.
If PROFILETYPE in
the IPCLKLNK MO
is set to G.8265.1,
CLKSYNCMODE in
the Tasm MO must Services of the cells
be set to FREQ. recover after the
Read & Write Yes Cells
If IPMODE in the reference clock is
IPCLKLNK MO is locked again.
set to IPV6,
CLKSYNCMODE in
the Tasm MO must
be set to FREQ.


Services are
interrupted until the
None Read & Write Yes BS
reference clock is
qualified.
When AT in the
RRUCHAIN MO is
set to PEERPORT,
the board specified
by HSN must have
not been
configured.
When AT in the
RRUCHAIN MO is
set to PEERPORT,
if HSN equal to 2,
the BBP with the
value of SN equal
to 3 must have
been configured; if
HSN equal to 3, the
BBP with the value
of SN equal to 2
must have been
configured.

In the RRUCHAIN
MO, when TT is set
to RING or The services
LOADBALANCE, carried on the
WM in the BBP MO baseband
corresponding to processing board
HCN, HSRN, and Read & Write Yes and the services Less than 1 minute
HSN must be the carried on RF
same as the WM in modules connected
the BBP MO to the baseband
corresponding to processing board
TCN, TSRN, and
TSN.
No (And no impact
mode)
No (And no impact
mode)
Less than 2
None Read & Write Yes The operated board
minutes









No (And no impact
mode)
No (And no impact
mode)
MPN in the CCU

No (And no impact
MOs under the
same manager unit
mode)
must be the same.
No (And no impact
mode)
CCN in the CCU

No (And no impact
MOs under the
same manager unit
mode)
must be unique.
In the CCU MO, CS No (And no impact

is valid only when Read & Write on the UE in idle N/A N/A
DCF is set to YES. mode)
No (And no impact
mode)



CN, SRN and SN in

the CpriPort must
meet the following
conditions: 1. when
CN is set to 0, SRN
must be set to 0~1,
4~5 or 60~254; 2.
when CN is set to
1~7, SRN must be
set to 0~1, 4~5; 3.
when CN is set to
8~62, SRN must be
set to 4~5; 4. when
SRN is set to 0~1,
SN must be set to
0~7; 5. when SRN
is set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
6. when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
7. when SRN is set
to 60~254, SN must
be set to 0.
CN, SRN and SN in
the CpriPort must
meet the following
conditions: 1. when
CN is set to 0, SRN
must be set to 0~1,
4~5 or 60~254; 2.
when CN is set to
1~7, SRN must be
set to 0~1, 4~5; 3.
when CN is set to
8~62, SRN must be
set to 4~5; 4. when
SRN is set to 0~1,
SN must be set to
0~7; 5. when SRN
is set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
6. when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
7. when SRN is set
to 60~254, SN must
be set to 0.
CN, SRN and SN in
the CpriPort must
meet the following
conditions: 1. when
CN is set to 0, SRN
must be set to 0~1,
4~5 or 60~254; 2.
when CN is set to
1~7, SRN must be
set to 0~1, 4~5; 3.
when CN is set to
8~62, SRN must be
set to 4~5; 4. when
SRN is set to 0~1,
SN must be set to
0~7; 5. when SRN
is set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
6. when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
7. when SRN is set
to 60~254, SN must
be set to 0.



No (And no impact
mode)










No (And no impact
mode)





No (And no impact
mode)



















No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
ET in the
No (And no impact
Equipment MO
must be later than
mode)
ST.
ET in the
No (And no impact
Equipment MO
must be later than
mode)
ST.
No (And no impact
mode)
No (And no impact
mode)
In the Equipment
MO, the value of
No (And no impact
DVAH must be
smaller than or
mode)
equal to the value
of DVAL minus 5.
In the Equipment
MO, the value of
No (And no impact
DVAH must be
smaller than or
mode)
equal to the value
of DVAL minus 5.

when TYPE in the
Cabinet MO is set
to one of the
following values:
RFC, BTS3900,
BTS3900L,
VIRTUAL,
BTS3900AL, and
ILC29.
TYPE in the
Subrack MO can
be set to RFU only
when TYPE in the
Cabinet MO is set
to one of the
following values:
RFC, BTS3900,
BTS3900L,
No (And no impact
VIRTUAL, and
BTS3900AL.
mode)
TYPE in the
Subrack MO can
be set to BBU3900
only when TYPE in
the Cabinet MO is
set to one of the
following values:
APM30, TMC,
OMB, BTS3900,
BTS3900L,
BTS3900AL,
PS4890,
TP48600A,
VIRTUAL, and
ILC29.
SRN in the BBU
subrack MO must
be set to 0 when
No (And no impact
mode)

When the value of
CN ranges from 0
to 7 and SRN is set
to 0 or 1, TYPE in
the Subrack MO
can be set to
BBU3900. When
the value of CN
ranges from 0 to 62
and SRN is set to 4 Read Only N/A N/A N/A
or 5, TYPE in the
Subrack MO must
be set to RFU.
In a Subrack MO,
when TYPE is set
to BBU3900, the
value of CN must
be smaller than or
equal to 7.
SRN in the BBU

subrack MO must
be set to 0 when
TYPE in the
Cabinet MO is set
to OMB.
In a Subrack MO,
when TYPE is set
to BBU3900, SRN
must be set to 0 or
1.
In a Subrack MO,
when TYPE is set
to RFU, SRN must
be set to 4 or 5.
In a Subrack MO,
when TYPE is set
to TCU, SRN must
be set to 8 or 14.
In a Subrack MO,
when TYPE is set
to FMU, SRN must
be set to 11 or 12.
In a Subrack MO,
when TYPE is set
to EMU, the value
of SRN must range
from 40 to 59.
In a Subrack MO,
when TYPE is set
to PMU, SRN must
be set to 7.
Cabinet MO is set
to one of the
following values:
RFC, BTS3900,
BTS3900L,
VIRTUAL,
BTS3900AL, and
ILC29.
TYPE in the
Subrack MO can
be set to RFU only
when TYPE in the
Cabinet MO is set
to one of the
following values:
RFC, BTS3900,
BTS3900L,
VIRTUAL, and
BTS3900AL.
TYPE in the
Subrack MO can
be set to BBU3900
only when TYPE in
the Cabinet MO is
set to one of the
following values:
APM30, TMC,
OMB, BTS3900,
BTS3900L,
BTS3900AL,
PS4890,
TP48600A,
VIRTUAL, and
ILC29.
In a Subrack MO,
when TYPE is set
to RFU, SRN must
be set to 4 or 5.
No (And no impact
mode)






No (And no impact
mode)
The manager unit

of an EMU MO
must be one of the
following: 1. A
Subrack MO with
the value of SRN No (And no impact
smaller than or Read & Write on the UE in idle N/A N/A
equal to 1; 2. A mode)
RRU MO with the
value of SRN
ranging from 60 to
254; 3. A CCU MO
with SRN set to 15.
In an EMU MO,
when MSRN is set
to 15, the value of
MPN must be
smaller than or
equal to 7. When
the value of MSRN
is greater than or No (And no impact
equal to 60, the Read & Write on the UE in idle N/A N/A
value of MPN must mode)
be equal to 0.
When the value of
MSRN is smaller
than or equal to 1,
the value of MPN
must be smaller
than or equal to 1.
No (And no impact
mode)
In an EMU MO, the

value of TUTHD
No (And no impact
minus the value of
TLTHD must be
mode)
greater than or
equal to 3.
In an EMU MO, the

value of TUTHD
No (And no impact
minus the value of
TLTHD must be
mode)
greater than or
equal to 3.
In an EMU MO, the
value of HUTHD
No (And no impact
minus the value of
HLTHD must be
mode)
greater than or
equal to 5.
In an EMU MO, the

value of HUTHD
No (And no impact
minus the value of
HLTHD must be
mode)
greater than or
equal to 5.
No (And no impact
mode)
No (And no impact
mode)






No (And no impact
mode)
The manager unit

of a FMU MO must
be one of the
following: 1. A
Subrack MO with
RRU MO with the
value of SRN
ranging from 60 to
254; 3. A CCU MO
with SRN set to 15.
In a FMU MO, when

MSRN is set to 15,
the value of MPN
must be smaller
than or equal to 7.
When the value of
MSRN is greater
No (And no impact
than or equal to 60,
the value of MPN
mode)
must be equal to 0.
When the value of
MSRN is smaller
than or equal to 1,
the value of MPN
must be smaller
than or equal to 1.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)




SRN in a TCU MO
can be set to 14
only when TYPE in
the Cabinet MO Read Only N/A N/A N/A
where the TCU MO
VIRTUAL.
SN in the TCU MO
must be set to 0
when TYPE in a
Cabinet MO where
the TCU MO is
located is set to
VIRTUAL, APM30,
TMC, or OMB.
SN in the TCU MO Read Only N/A N/A N/A
must be set to a
value smaller than
3 when TYPE in a
Cabinet MO where
the TCU MO is
located is set to
BBC or
BTS3900AL.
No (And no impact
mode)
The manager unit

of a TCU MO must
be one of the
following: 1. A
Subrack MO with
RRU MO with the
value of SRN
ranging from 60 to
254; 3. A CCU MO
with SRN set to 15.
In a TCU MO, when

MSRN is set to 15,
the value of MPN
must be smaller
than or equal to 7.
When the value of
MSRN is greater
No (And no impact
than or equal to 60,
the value of MPN
mode)
must be equal to 0.
When the value of
MSRN is smaller
than or equal to 1,
the value of MPN
must be smaller
than or equal to 1.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)






In the HtCDPa MO,

No (And no impact
the value of HTCP
must be greater
mode)
than LTCP.
In the HtCDPa MO,
No (And no impact
the value of HTCP
must be greater
mode)
than LTCP.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
The manager unit
of a PMU MO must
be one of the
following: 1. A
Subrack MO with
RRU MO with the
value of SRN
ranging from 60 to
254; 3. A CCU MO
with SRN set to 15.
In a PMU MO,
when MSRN is set
to 15, the value of
MPN must be
smaller than or
equal to 7. When
the value of MSRN
is greater than or No (And no impact
equal to 60, the Read & Write on the UE in idle N/A N/A
value of MPN must mode)
be equal to 0.
When the value of
MSRN is smaller
than or equal to 1,
the value of MPN
must be smaller
than or equal to 1.
No (And no impact
mode)
MO of the Battery
MO is set to
SC48200, BCV in
the Battery MO
must be greater
value of FCV plus
22.
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, TCC in
the Battery MO
must be smaller
than or equal to
100.
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, TUTHD
in the Battery MO
must be greater
than or equal to 35
and smaller than or
equal to 60.
When PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200 and
HTSDF in the
Battery MO is set
to ENABLE, SDT in
the Battery MO
must be greater
than or equal to 45
In a PMU MO,
when PTYPE is not
No (And no impact
set to SC48200, the
value of ACVLTHD
mode)
must be smaller
than ACVUTHD.
In a PMU MO,
when PTYPE is not
No (And no impact
set to SC48200, the
value of ACVLTHD
mode)
must be smaller
than ACVUTHD.
FCV in the Battery
MO corresponding
to the PMU MO
must be greater
than DCVLTHD in
the PMU MO plus
20.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than DCVLTHD in
the PMU under the
following
conditions: 1. LSDF
in the PMU MO is
set to DISABLE; 2.
LVSDF in the
No (And no impact
Battery MO
corresponding to
mode)
the PMU MO is set
to ENABLE; 3.
PTYPE in the PMU
MO is set to a value
other than
SC48200.
In a PMU MO,
when PTYPE is set
to SC48200, the
value of DCVLTHD
must be greater
than or equal to 460
and smaller than or
equal to 500, and
the value of
DCVUTHD must be
greater than or
equal to 580 and
In a PMU MO,
when PTYPE is set
to SC48200, BCV
in the Battery MO
corresponding to
the PMU MO must
be smaller than or
equal to DCVUTHD
in the PMU MO
minus 15.
In a PMU MO,
when PTYPE is set
to a value other
than SC48200,
BCV in the Battery
MO corresponding
to the PMU MO No (And no impact
must be smaller Read & Write on the UE in idle N/A N/A
than DCVUTHD in mode)
the PMU MO minus
10.
In a PMU MO,
when PTYPE is set
to SC48200, the
value of DCVLTHD
must be greater
and smaller than or
equal to 500, and
the value of
DCVUTHD must be
greater than or
equal to 580 and
smaller than or
equal to 600.
PTYPE in the PMU
MO is set to
SC48200; 2. LSDF
in the PMU MO is
set to ENABLE; 3.
LVSDF in the
Battery MO
corresponding to
the PMU MO is also
set to ENABLE.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than DCVLTHD in
the PMU under the
following
conditions: 1. LSDF
No (And no impact
in the PMU MO is
set to DISABLE; 2.
mode)
LVSDF in the
Battery MO
corresponding to
the PMU MO is set
to ENABLE; 3.
PTYPE in the PMU
other than
SC48200.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than LSDV in the
PMU under the
following
conditions: 1. LSDF
in the PMU MO is
corresponding to
the PMU MO is also
set to ENABLE.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than LSDV in the
PMU under the
following
conditions: 1. LSDF
in the PMU MO is
set to ENABLE; 2.
LVSDF in the
Battery MO
corresponding to
the PMU MO is set
to ENABLE; 3.
No (And no impact
PTYPE in the PMU
mode)
other than
SC48200.
In a PMU MO,
when PTYPE and
LSDF are set to
SC48200 and
ENABLE,
respectively, the
value of LSDV must
be greater than or
equal to 455 and
smaller than or
equal to 485.
In a PMU MO,
when the values of
PTYPE and LSDF
are set to SC48200
and ENABLE,
No (And no impact
mode)
No (And no impact
mode)
In a PMU MO,
No (And no impact
AHLTHD must be
smaller than
mode)
AHUTHD.
In a PMU MO,
No (And no impact
AHLTHD must be
smaller than
mode)
AHUTHD.
No (And no impact
mode)
No (And no impact
mode)










No (And no impact
mode)
No (And no impact
mode)

If PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200,
INSTALLTYPE in
the Battery MO
must be set to No (And no impact
INNER or OUTER. Read & Write on the UE in idle N/A N/A
If PTYPE in the mode)
upper-level PMU
MO of the Battery
MO is set to
SC48200,
INSTALLTYPE in
the Battery MO
must be set to
OUTER.
No (And no impact
mode)
to a value other
than SC48200,
BCV in the Battery
MO corresponding
to the PMU MO
must be smaller
than DCVUTHD in
the PMU MO minus
10.
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, BCV in
the Battery MO
must be greater
and smaller than or No (And no impact
equal to 575. Read & Write on the UE in idle N/A N/A
upper-level PMU
MO of the Battery
MO is set to
SC48200, BCV in
the Battery MO
must be greater
value of FCV plus
22.
If PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200, BCV in
the Battery MO
must be greater
in the Battery MO
is 1, BC1 in the
Battery MO must
be greater than or
equal to 5 and
smaller than or
equal to 5000; If
PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200, and BN
in the Battery MO
is 2, BC1 and BC2
in the Battery MO
must be greater
than or equal to 5
No (And no impact
and smaller than or
equal to 5000.
mode)
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, and BN
in the Battery MO
is 1, BC1 in the
Battery MO must
be greater than or
equal to 50 and
smaller than or
equal to 5000; If
PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, and BN
in the Battery MO
No (And no impact
mode)
when PTYPE is set
to a value other
than SC48200,
FCV in the Battery
MO corresponding
to the PMU MO
must be greater
than DCVLTHD in
the PMU MO plus
20.
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, FCV in
the Battery MO
must be greater
than or equal to 520 No (And no impact
and smaller than or Read & Write on the UE in idle N/A N/A
equal to 563. mode)
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, BCV in
the Battery MO
must be greater
value of FCV plus
22.
If PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200, FCV in
the Battery MO
When PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200 and
HTSDF in the No (And no impact
Battery MO is set Read & Write on the UE in idle N/A N/A
to ENABLE, SDT in mode)
the Battery MO
must be greater
than or equal to 45
and smaller than or
equal to 70.
of SDT is from 40 to
70.
The SDT is valid
only when HTSDF
in the Battery MO
is set to ENABLE.
SDT in the Battery
MO must be greater
than TUTHD.
If PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200, SDT in
the Battery MO
must be greater
than or equal to 40 No (And no impact
and smaller than or Read & Write on the UE in idle N/A N/A
equal to 70. mode)
When PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200 and
HTSDF in the
Battery MO is set
to ENABLE, SDT in
the Battery MO
must be greater
than or equal to 45
and smaller than or
equal to 70.
When PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
the PMU MO is also
set to ENABLE.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than DCVLTHD in
the PMU under the
following
conditions: 1. LSDF
in the PMU MO is
set to DISABLE; 2.
LVSDF in the
Battery MO
corresponding to
the PMU MO is set
to ENABLE; 3.
PTYPE in the PMU
No (And no impact
other than
mode)
SC48200.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than LSDV in the
PMU under the
following
conditions: 1. LSDF
in the PMU MO is
set to ENABLE; 2.
LVSDF in the
Battery MO
corresponding to
the PMU MO is set
to ENABLE; 3.
PTYPE in the PMU
in the PMU MO is
set to DISABLE; 2.
LVSDF in the
Battery MO
corresponding to
the PMU MO is set
to ENABLE; 3.
PTYPE in the PMU
other than
SC48200.
SDV in the Battery
MO corresponding
to the PMU MO
must be smaller
than LSDV in the
PMU under the
following
No (And no impact
conditions: 1. LSDF
in the PMU MO is
mode)
set to ENABLE; 2.
LVSDF in the
Battery MO
corresponding to
the PMU MO is set
to ENABLE; 3.
PTYPE in the PMU
other than
SC48200.
When PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200 and
LVSDF in the
Battery MO is set
If
toPTYPE
ENABLE,in the
SDV in
upper-level PMU
MO of the Battery
other than
SC48200, TCC in
the Battery MO
must be smaller
than or equal to No (And no impact
500. Read & Write on the UE in idle N/A N/A
upper-level PMU
MO of the Battery
MO is set to
SC48200, TCC in
the Battery MO
must be smaller
than or equal to
100.
No (And no impact
mode)
Battery MO must
be greater than
TLTHD,and be
smaller than SDT.
If PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200, TUTHD
in the Battery MO
must be greater
than or equal to 35
and smaller than or
equal to 80.
If PTYPE in the
upper-level PMU
MO of the Battery No (And no impact
MO is set to Read & Write on the UE in idle N/A N/A
SC48200, TUTHD mode)
in the Battery MO
must be greater
than or equal to 35
and smaller than or
equal to 60.
When PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200 and
HTSDF in the
Battery MO is set
to ENABLE, SDT
must be greater
than or equal to
TUTHD in the
Battery MO plus
The BN is valid only
when BTYPE in the
Battery MO is set
No (And no impact
to LI_BAT.
Except the
mode)
TP48300A type
PMU, the Battery
BN must be 1.
No (And no impact
mode)




in the Battery MO
is 1, BC1 in the
Battery MO must
be greater than or
equal to 5 and
smaller than or
equal to 5000; If
PTYPE in the
upper-level PMU
MO of the Battery
other than
SC48200, and BN
in the Battery MO
is 2, BC1 and BC2
in the Battery MO
must be greater
than or equal to 5
No (And no impact
and smaller than or
equal to 5000.
mode)
If PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, and BN
in the Battery MO
is 1, BC1 in the
Battery MO must
be greater than or
equal to 50 and
smaller than or
equal to 5000; If
PTYPE in the
upper-level PMU
MO of the Battery
MO is set to
SC48200, and BN
in the Battery MO

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In a BatCTPa MO,
when ATMODE is
set to PERIOD or
No (And no impact
PERIODPOWERC
UT, the value of
mode)
TDSTM must be
greater than the
value of DDSTM.
In a BatCTPa MO,
when ATMODE is
set to PERIOD or
No (And no impact
PERIODPOWERC
UT, the value of
mode)
TDSTM must be
greater than the
value of DDSTM.


EPS48200, SN in
the lower-level PSU
MO must be greater
than or equal to 1
and smaller than or
equal to 4.
If PTYPE in the
PMU MO is set to
TP48300A, SN in
the lower-level PSU
MO must be greater
than or equal to 1
and smaller than or
equal to 6.
If PTYPE in the
PMU MO is set to
ETP, SN in the
lower-level PSU
MO must be greater Read Only N/A N/A N/A
than or equal to 1
and smaller than or
equal to 7.
If PTYPE in the
PMU MO is set to
APM30, SN in the
lower-level PSU
MO must be greater
than or equal to 1
and smaller than or
equal to 5.
If PTYPE in the
PMU MO is not set
to any of the
following values,
SN in the lower-
level PSU MO must
be greater than or






No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
an EMU MO, and
the value of SRN in
this EMU MO
ranges from 40 to
59; 2. The value of
PN ranges from 0
to 31; 3. SW is set
to ON.In the
AlmPort MO, PT
must be set to
BOOL when all the
are met: 1. The
device
corresponding to
the AlmPort MO is
not an EMU MO; 2.
SW is set to ON.
In the AlmPort MO, Read Only N/A N/A N/A
PT must be set to
VALUE when all the
are met: 1. The
device
corresponding to
the AlmPort MO is
an EMU MO, and
the value of SRN in
this EMU MO
ranges from 40 to
59; 2. The value of
PN ranges from 32
to 35; 3. SW is set
to ON.
In the AlmPort MO,
when SW is set to
ON and PT is to
The AVOL is valid

No (And no impact
only when PT in the
AlmPort MO is set
mode)
to BOOL.
The UL is valid only
when PT in the
AlmPort MO is set
to VALUE.
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of UL must No (And no impact
be greater than the Read & Write on the UE in idle N/A N/A
value of LL. mode)
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of SMUL
must be greater
value of UL.
The LL is valid only
when PT in the
AlmPort MO is set
to VALUE.
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of UL must No (And no impact
be greater than the Read & Write on the UE in idle N/A N/A
value of LL. mode)
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of SMLL must
be smaller than or
equal to the value
of LL.
In the AlmPort MO,

No (And no impact
the ST is valid only
when PT is set to
mode)
VALUE.
The SMUL is valid
only when PT in the
AlmPort MO is set
to VALUE.
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of SMUL
No (And no impact
must be greater
than the value of
mode)
SMLL.
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of SMUL
must be greater
value of UL.
The SMLL is valid

only when PT in the
AlmPort MO is set
to VALUE.
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of SMUL
No (And no impact
must be greater
than the value of
mode)
SMLL.
In the AlmPort MO,
when the values of
SW and PT are set
to ON and VALUE,
respectively, the
value of SMLL must
be smaller than or
equal to the value
of LL.
The SOUL is valid

only when PT in the
AlmPort MO is set
to VALUE.
In the AlmPort MO,
when the values of No (And no impact
SW and PT are set Read & Write on the UE in idle N/A N/A
to ON and VALUE, mode)
respectively, the
value of SOUL
must be greater
than the value of
SOLL.
The SOLL is valid
only when PT in the
AlmPort MO is set
to VALUE.
In the AlmPort MO,
when the values of No (And no impact
SW and PT are set Read & Write on the UE in idle N/A N/A
to ON and VALUE, mode)
respectively, the
value of SOUL
must be greater
than the value of
SOLL.
No (And no impact
mode)
No (And no impact
mode)
Each AAU MO
must have a unique
combination of CN,
SRN, and SN
among all MOs as
follows: RRU, AAU.
Each AAU MO
must have a unique
combination of CN,
SRN, and SN
among all MOs as
follows: RRU, AAU.
Each AAU MO
must have a unique
combination of CN,
SRN, and SN
among all MOs as
follows: RRU, AAU.
No (And no impact
mode)
No (And no impact
mode)
The cells carried on

Till unblocking is
None Read & Write Yes the RRU or RFU is
performed.
unavailable.




No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
RRU MO or RFU
MO cannot be
removed when one
of the following
conditions is met: 1.
BRKPOS1 is set to
255; 2. BRKPOS1
and BRKPOS2 are
not set to the same
value, and PS in
the RRU MO or PS
in the RFU MO is
smaller than
BRKPOS1 or is
greater than or
equal to
BRKPOS2; 3.
BRKPOS1 and
BRKPOS2 are set
to the same value.
When TT in the
RRUCHAIN MO
where the RRU MO
or RFU MO is
located is set to
CHAIN,and AT is
set to
LOCALPORT,and
TP in the RRU MO
or TP in the RFU
MO is set to
TRUNK, the RRU
MO or RFU MO
cannot be removed
when one of the
following two
BRKPOS1 is set to
None Read & Write Yes Cell <1

Until the execution
Services carried by of the MOD RRU
None Read & Write Yes
the RRU or RFU command is
successful
No (And no impact
mode)
No (And no impact
mode)






Till unblocking is
performed.
unavailable.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
RRU MO or RFU
MO cannot be
removed when one
of the following
BRKPOS1 is set to
255; 2. BRKPOS1
and BRKPOS2 are
not set to the same
value, and PS in
the RRU MO or PS
in the RFU MO is
smaller than
BRKPOS1 or is
greater than or
equal to
BRKPOS2; 3.
BRKPOS1 and
BRKPOS2 are set
to the same value.
When TT in the
RRUCHAIN MO
where the RRU MO
or RFU MO is
located is set to
CHAIN,and AT is
set to
LOCALPORT,and
TP in the RRU MO
or TP in the RFU
MO is set to
TRUNK, the RRU
MO or RFU MO
cannot be removed
when one of the
following two
BRKPOS1 is set to

Until the execution
successful
No (And no impact
mode)
No (And no impact
mode)








When the value of

SN in the RFU MO
is greater than 5,
TYPE in the
corresponding
Cabinet MO must
be set to
BTS3900AL.

None Read & Write Yes the RRU are <1
unavailable.
Till unblocking is
performed.
unavailable.




No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
RRU MO or RFU
MO cannot be
removed when one
of the following
BRKPOS1 is set to
255; 2. BRKPOS1
and BRKPOS2 are
not set to the same
value, and PS in
the RRU MO or PS
in the RFU MO is
smaller than
BRKPOS1 or is
greater than or
equal to
BRKPOS2; 3.
BRKPOS1 and
BRKPOS2 are set
to the same value.
When TT in the
RRUCHAIN MO
where the RRU MO
or RFU MO is
located is set to
CHAIN,and AT is
set to
LOCALPORT,and
TP in the RRU MO
or TP in the RFU
MO is set to
TRUNK, the RRU
MO or RFU MO
cannot be removed
when one of the
following two
BRKPOS1 is set to

Until the execution
successful
No (And no impact
mode)
No (And no impact
mode)





Each RRU MO
must have a unique
combination of CN,
SRN, and SN
among all RRU
MOs.
Each RRU MO
must have a unique
combination of CN,
SRN, and SN
among all RRU
MOs.
Each RRU MO
must have a unique
combination of CN,
SRN, and SN
among all RRU
MOs.
No (And no impact
mode)
The RRU MO
needs to be reset
after the RT of this
RRU MO is
changed.
In the RRU MO, RT
must be set to
Read & Write Yes the RRU are <1
MRRU or LRRU
unavailable.
when RS is set to
LTE_TDD.
In the RRU MO, RT
must be set to
MRRU when RS is
set to WiMAX_LTE.

Till unblocking is
performed.
unavailable.




No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
RRU MO or RFU
MO cannot be
removed when one
of the following
BRKPOS1 is set to
255; 2. BRKPOS1
and BRKPOS2 are
not set to the same
value, and PS in
the RRU MO or PS
in the RFU MO is
smaller than
BRKPOS1 or is
greater than or
equal to
BRKPOS2; 3.
BRKPOS1 and
BRKPOS2 are set
to the same value.
When TT in the
RRUCHAIN MO
where the RRU MO
or RFU MO is
located is set to
CHAIN,and AT is
set to
LOCALPORT,and
TP in the RRU MO
or TP in the RFU
MO is set to
TRUNK, the RRU
MO or RFU MO
cannot be removed
when one of the
following two
BRKPOS1 is set to

Until the execution
successful
No (And no impact
mode)
No (And no impact
mode)






RRUCHAIN MO are
changed.
In the RRUCHAIN
MO, when TT is set
to RING and this
value needs to be
changed,
BRKPOS2 must be
the same as the
total number of
MOs configured on
the trunk of the
RRU chain or ring.
In the RRUCHAIN
MO, when TT is
changed,
BRKPOS1 must be After the command
set to 0. The cells carried by takes effect, the
In the RRUCHAIN the RRUs on the cells carried by the
Read & Write Yes
MO, when TT is set RRU chain/ring are RRUs on the RRU
to RING or unavailable. chain/ring become
LOADBALANCE, available.
WM in the BBP MO
corresponding to
HCN, HSRN, and
HSN must be the
same as the WM in
the BBP MO
corresponding to
TCN, TSRN, and
TSN.
When RT in the
RFU MO is set to
LRFU, TT in the
RRUCHAIN MO
corresponding to
RCN cannot be set
to LOADBALANCE.
When TT in the
RRUCHAIN MO is
After the command
set to CHAIN, BM
The cells carried by takes effect, the
must be set to
the RRUs on the cells carried by the
COLD. When TT in Read & Write Yes
RRU chain/ring are RRUs on the RRU
the RRUCHAIN MO
unavailable. chain/ring become
is set to RING, BM
available.
can be set to COLD
or HOT.
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available; 2. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
After the command
the CpriPort MO
specified by the
combination of Read & Write Yes
TCN, TSRN, TSN,
and TPN must be
available.
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available.
In the RRUCHAIN
MO, when TT is set
to RING and BM is
set to HOT, the
combination of
HCN, HSRN, and
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available; 2. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
After the command
the CpriPort MO
specified by the
combination of Read & Write Yes
TCN, TSRN, TSN,
and TPN must be
available.
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available.
In the RRUCHAIN
MO, when TT is set
to RING and BM is
set to HOT, the
combination of
HCN, HSRN, and
A RRUCHAIN MO
must meet the
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available; 2. When
TT in the
RRUCHAIN MO is
After the command
set to RING or
LOADBALANCE,
the CpriPort MO Read & Write Yes
specified by the
combination of
available.
TCN, TSRN, TSN,
and TPN must be
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available.
In the RRUCHAIN
MO, HSN must be
set to 2 or 3 if AT is
set to PEERPORT.
LOADBALANCE,
the combination of
HCN, HSRN, HSN,
and HPN cannot be
the same as the
combination of
TCN, TSRN, TSN,
and TPN.
A RRUCHAIN MO
must meet the
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO After the command
specified by the The cells carried by takes effect, the
combination of the RRUs on the cells carried by the
Read & Write Yes
HCN, HSRN, HSN, RRU chain/ring are RRUs on the RRU
and HPN must be unavailable. chain/ring become
available; 2. When available.
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
TCN, TSRN, TSN,
and TPN must be
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
A RRUCHAIN MO
must meet the
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available; 2. When
TT in the
RRUCHAIN MO is
After the command
set to RING or
LOADBALANCE,
specified by the
combination of
available.
TCN, TSRN, TSN,
and TPN must be
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available.
In the RRUCHAIN
MO, when TT is set
to RING and BM is
set to HOT, the
A RRUCHAIN MO
must meet the
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available; 2. When
TT in the
RRUCHAIN MO is
After the command
set to RING or
LOADBALANCE,
specified by the
combination of
available.
TCN, TSRN, TSN,
and TPN must be
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available.
In the RRUCHAIN
MO, when TT is set
to RING and BM is
set to HOT, the
the same as the
combination of
TCN, TSRN, TSN,
and TPN.
A RRUCHAIN MO
must meet the
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
After the command
and HPN must be
available; 2. When
TT in the Read & Write Yes
RRUCHAIN MO is
set to RING or
available.
LOADBALANCE,
the CpriPort MO
specified by the
combination of
TCN, TSRN, TSN,
and TPN must be
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
specified by the
combination of
HCN, HSRN, HSN,
and HPN must be
available.
MO, when TT is set
to RING or
LOADBALANCE,
the combination of
HCN, HSRN, HSN,
and HPN cannot be
the same as the
combination of
TCN, TSRN, TSN,
and TPN.
A RRUCHAIN MO
must meet the
following
conditions: 1. When
TT in the
RRUCHAIN MO is
set to RING or After the command
LOADBALANCE, The cells carried by takes effect, the
the CpriPort MO the RRUs on the cells carried by the
Read & Write Yes
specified by the RRU chain/ring are RRUs on the RRU
combination of unavailable. chain/ring become
HCN, HSRN, HSN, available.
and HPN must be
available; 2. When
TT in the
RRUCHAIN MO is
set to RING or
LOADBALANCE,
the CpriPort MO
specified by the
combination of
TCN, TSRN, TSN,
and TPN must be
available; 3. When
TT in the
RRUCHAIN MO is
set to CHAIN, the
CpriPort MO
MO, when TT is not
set to CHAIN and
BRKPOS1 is not
set to 255,
BRKPOS2 cannot
be set to 255.
In the RRUCHAIN
MO, when TT is not
set to CHAIN and
BRKPOS1 is set to
255, BRKPOS2
must be set to 255.
In the RRUCHAIN
MO, when TT is not The cells carried by
set to CHAIN, the RRUs behind
BRKPOS1 must be the breakpoint on
The cells carried by
smaller than or the RRU chain
the RRUs on the
equal to become
RRU chain/ring
BRKPOS2. unavailable. The
Read & Write Yes become available
If BRKPOS1 or cells carried by the
after the
BRKPOS2 in the RRUs between
breakpoints are
RRUCHAIN MO is breakpoints 1 and 2
removed.
not set to 255, the on the RRU ring
values of become
BRKPOS1 and unavailable.
BRKPOS2 must be
smaller than or
equal to the total
number of RRU and
RFU MOs on the
trunk of the RRU
chain or ring.
In a RRUCHAIN
MO, when AT is set
to PEERPORT,
BRKPOS1 must be
set to
255,BRKPOS2
set to 255.
In the RRUCHAIN
MO, when TT is not
set to CHAIN and
BRKPOS1 is not
set to 255,
BRKPOS2 cannot
be set to 255.
In the RRUCHAIN
MO, when TT is not
set to CHAIN and
BRKPOS1 is set to
255, BRKPOS2
must be set to 255.
In the RRUCHAIN
MO, when TT is not The cells carried by
The cells carried by
set to CHAIN, the RRUs on the
the RRUs between
BRKPOS1 must be RRU chain/ring
the breakpoints 1
smaller than or Read & Write Yes become available
and 2 on the RRU
equal to after the
ring are
BRKPOS2. breakpoints are
unavailable.
If BRKPOS1 or removed.
BRKPOS2 in the
RRUCHAIN MO is
not set to 255, the
values of
BRKPOS1 and
BRKPOS2 must be
smaller than or
equal to the total
number of RRU and
RFU MOs on the
trunk of the RRU
chain or ring.
In a RRUCHAIN
MO, when AT is set
to PEERPORT,
set to PEERPORT.
When AT in the
RRUCHAIN is set
to PEERPORT, the
RS in the RRU on
this RRUCHAIN
must be set to
LTE_FDD or
UMTS_ONLY, or
UMTS_LTE, and
the RT in the RRU
on this RRUCHAIN
must be set to
MRRU or PRRU.
In a RRUCHAIN
MO, when AT is set
to PEERPORT, CR After the command
must be set to The cells carried by takes effect, the
AUTO. the RRUs on the cells carried by the
Read & Write Yes
When AT in the RRU chain/ring are RRUs on the RRU
RRUCHAIN MO is unavailable. chain/ring become
set to PEERPORT, available.
the board specified
by HSN must have
not been
configured.
When AT in the
RRUCHAIN MO is
set to PEERPORT,
if HSN equal to 2,
the BBP with the
value of SN equal
to 3 must have
been configured; if
HSN equal to 3, the
BBP with the value
of SN equal to 2
must have been
Services are
restored
Cells carried on the immediately after
RRU chain. the RRU finishes
negotiating this rate
with the BBU.
CN,SRN and SN in
the RxBranch must
meet the following
conditions: 1.when
CN is set to 0, SRN
must be set to 4~5
or 60~254; 2.when
CN is set to 1~62,
SRN must be set to
4~5; 3.when SRN is
set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
4.when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
5.when SRN is set
to 60~254, SN must
be set to 0.
CN,SRN and SN in
the RxBranch must
meet the following
conditions: 1.when
CN is set to 0, SRN
must be set to 4~5
or 60~254; 2.when
CN is set to 1~62,
SRN must be set to
4~5; 3.when SRN is
set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
4.when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
5.when SRN is set
to 60~254, SN must
be set to 0.
CN,SRN and SN in
the RxBranch must
meet the following
conditions: 1.when
CN is set to 0, SRN
must be set to 4~5
or 60~254; 2.when
CN is set to 1~62,
SRN must be set to
4~5; 3.when SRN is
set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
4.when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
5.when SRN is set
to 60~254, SN must
be set to 0.
Services on the When the logical

None Read & Write Yes channel are switch of RX
affected. channel is ON
When the TMA MO

is not used, ATTEN
in the RxBranch
MO is set to 0.
When the 12dB
TMA MO is used, No (And no impact
the value of ATTEN Read & Write on the UE in idle N/A N/A
ranges from 4 dB to mode)
11 dB. When the
24dB TMA MO is
used, the value of
ATTEN ranges from
11 dB to 22 dB.


CN, SRN and SN in
the TxBranch must
meet the following
conditions: 1.when
CN is set to 0, SRN
must be set to 4~5
or 60~254; 2.when
CN is set to 1~62,
SRN must be set to
4~5; 3.when SRN is
set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
4.when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
5.when SRN is set
to 60~254, SN must
be set to 0.
CN, SRN and SN in

the TxBranch must
meet the following
conditions: 1.when
CN is set to 0, SRN
must be set to 4~5
or 60~254; 2.when
CN is set to 1~62,
SRN must be set to
4~5; 3.when SRN is
set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
4.when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
5.when SRN is set
to 60~254, SN must
be set to 0.
CN, SRN and SN in
the TxBranch must
meet the following
conditions: 1.when
CN is set to 0, SRN
must be set to 4~5
or 60~254; 2.when
CN is set to 1~62,
SRN must be set to
4~5; 3.when SRN is
set to 4~5 and
TYPE in the
Cabinet is equal to
BTS3900AL, SN
must be set to 0~8;
4.when SRN is set
to 4~5 and TYPE in
the Cabinet is not
equal to
BTS3900AL, SN
must be set to 0~5;
5.when SRN is set
to 60~254, SN must
be set to 0.

Services carried on
Less than 2
None Read & Write Yes the specified TX
minutes
channel




This parameter is
valid only when
MODE in the
NtpCp MO is IPV4.
No (And no impact
mode)
No (And no impact
mode)
This parameter is
valid only when
MODE in the
NtpCp MO is IPV6.
No (And no impact
mode)
This parameter is
AUTHMODE is set Read & Write on the UE in idle N/A N/A
to a value other mode)
than PLAIN.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
This parameter is
No (And no impact
valid only when
DST in the TZ MO
mode)
is set to YES.
When DST in the

TZ MO is set to
YES, SMONTH
should not be equal
to EMONTH. No (And no impact
This parameter is Read & Write on the UE in idle N/A N/A
valid only when mode)
DST in the TZ MO
is set to YES and
SM is DATEWEEK,
DATE, or WEEK.
When DST in the

TZ MO is set to
YES and SM is
DATEWEEK, SDAY
plus 6 should not
be beyond the end
of the month
specified by
SMONTH.
When DST in the
No (And no impact
TZ MO is set to
YES and SM is
mode)
DATE, if SMONTH
is FEB, then SDAY
should not be
greater than 28.
This parameter is
valid only when
DST in the TZ MO
is set to YES and
SM is DATEWEEK
or DATE.
This parameter is
DST in the TZ MO Read & Write on the UE in idle N/A N/A
is set to YES and mode)
SM is WEEK.
This parameter is
valid only when
No (And no impact
DST in the TZ MO
is set to YES and
mode)
SM is DATEWEEK
or WEEK.
This parameter is
No (And no impact
valid only when
DST in the TZ MO
mode)
is set to YES.
This parameter is
No (And no impact
valid only when
DST in the TZ MO
mode)
is set to YES.
This parameter is
valid only when
DST in the TZ MO
is set to YES and
EM is DATEWEEK,
No (And no impact
DATE, or WEEK.
When DST in the
mode)
TZ MO is set to
YES, SMONTH and
EMONTH are not
allowed to be
identical.
When DST in the
TZ MO is set to
YES and EM is
DATEWEEK, EDAY
plus 6 should not
be beyond the end
of the month
specified by
EMONTH.
This parameter is
No (And no impact
valid only when
DST in the TZ MO
mode)
is set to YES and
EM is DATEWEEK
or DATE.
When DST in the
TZ MO is set to
YES and EM is
DATE, if EMONTH
is FEB, then EDAY
should not be
greater than 28.
This parameter is
DST in the TZ MO Read & Write on the UE in idle N/A N/A
is set to YES and mode)
EM is WEEK.
This parameter is
valid only when
No (And no impact
DST in the TZ MO
is set to YES and
mode)
EM is DATEWEEK
or WEEK.
This parameter is
No (And no impact
valid only when
DST in the TZ MO
mode)
is set to YES.
This parameter is
No (And no impact
valid only when
DST in the TZ MO
mode)
is set to YES.
This parameter is
ZONET in the TZ Read & Write on the UE in idle N/A N/A
MO is set to mode)
CUSTOM.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
FTPCLTPORT MO,
SERVERIP cannot
be set to 255.x.x.x.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)

In the
CSFallBackBlindH
oCfg MO,
InterRatHighestPri
must be different
from
InterRatLowestPri. No (And no impact
In the Read & Write on the UE in idle N/A N/A
CSFallBackBlindH mode)
oCfg MO,
InterRatHighestPri
must be different
from
InterRatSecondPri
.
In the
CSFallBackBlindH
oCfg MO,
InterRatHighestPri
must be different
from
InterRatSecondPri
No (And no impact
.
In the
mode)
CSFallBackBlindH
oCfg MO,
InterRatLowestPri
must be set to
NULL if
InterRatSecondPri
is set to NULL.
In the
CSFallBackBlindH
oCfg MO,
InterRatHighestPri
must be different
from
InterRatLowestPri.
In the
CSFallBackBlindH
oCfg MO,
InterRatLowestPri
must be set to No (And no impact
NULL if Read & Write on the UE in idle N/A N/A
InterRatSecondPri mode)
is set to NULL.
In the
CSFallBackBlindH
oCfg MO,
InterRatSecondPri
must be different
from
InterRatLowestPri
if
InterRatSecondPri
is not set to NULL.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)


In the same
RAT/frequency
priority group
specified by
No (And no impact
RatFreqPriorityGr
oupId, frequencies
mode)
used for different
RATs must be
assigned different
priorities.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
ENodeBCipherCap
MO, the
PrimaryCipherAlg
o, No (And no impact
SecondCipherAlg Read & Write on the UE in idle N/A N/A
o, and mode)
ThirdCipherAlgo
parameters must be
set to different
values.
In the
ENodeBCipherCap
MO, the
PrimaryCipherAlg
o, and mode)
ThirdCipherAlgo
parameters must be
set to different
values.
In the
ENodeBCipherCap
MO, the
PrimaryCipherAlg
o, and mode)
ThirdCipherAlgo
parameters must be
set to different
values.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
ENodeBIntegrityC
ap MO, the
PrimaryIntegrityAl
go, No (And no impact
SecondIntegrityAl Read & Write on the UE in idle N/A N/A
go, and mode)
ThirdIntegrityAlgo
parameters must be
set to different
values.
In the
ENodeBIntegrityC
ap MO, the
PrimaryIntegrityAl
go, and mode)
ThirdIntegrityAlgo
parameters must be
set to different
values.
In the
ENodeBIntegrityC
ap MO, the
PrimaryIntegrityAl
go, and mode)
ThirdIntegrityAlgo
parameters must be
set to different
values.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
Profiles in a
PdcpRohcPara
MO supports four
No (And no impact
profiles:
Profile0x0001,
mode)
Profile0x0002,
Profile0x0003, and
Profile0x0004.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
This parameter
must be set for
using a fixed
PDSCH power if
PdschSpsPcSwitch
under the No (And no impact
DlPcAlgoSwitch Read & Write on the UE in idle N/A N/A
parameter is turned mode)
off and the
DlIcicSwitch
parameter is set to
DlIcicSwitch_OFF_
ENUM.
In a CellDrxPara
MO, the value of
No (And no impact
FddEnterDrxThd
must be less than
mode)
the value of
FddExitDrxThd.
In a CellDrxPara
MO, the value of
No (And no impact
FddEnterDrxThd
must be less than
mode)
the value of
FddExitDrxThd.
In a CellDrxPara
MO, the value of
No (And no impact
TddEnterDrxThdUl
must be smaller
mode)
than that of
TddExitDrxThdUl.
In a CellDrxPara
MO, the value of
No (And no impact
TddEnterDrxThdUl
must be less than
mode)
the value of
TddExitDrxThdUl.
In a CellDrxPara
MO, the value of
No (And no impact
TddEnterDrxThdDl
must be less than
mode)
the value of
TddExitDrxThdDl.
In a CellDrxPara
MO, the value of
No (And no impact
TddEnterDrxThdDl
must be smaller
mode)
than that of
TddExitDrxThdDl.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
In a DrxParaGroup
MO, the value of
OnDurationTimer
cannot be greater
than the value of
LongDrxCycle. If
SupportShortDrx
is set to
No (And no impact
UU_ENABLE, the
value of
mode)
OnDurationTimer
cannot be greater
than the value of
ShortDrxCycle.
This parameter is
invalid when
EnterDrxSwitch is
set to OFF.
This parameter is
No (And no impact
invalid when
EnterDrxSwitch is
mode)
set to OFF.
This parameter is
No (And no impact
invalid when
EnterDrxSwitch is
mode)
set to OFF.
This parameter is
invalid when
EnterDrxSwitch is
set to OFF.
No (And no impact
In a DrxParaGroup
MO, the value of
mode)
OnDurationTimer
cannot be greater
than the value of
LongDrxCycle.
This parameter is
No (And no impact
invalid when
EnterDrxSwitch is
mode)
set to OFF.
This parameter is
invalid when
EnterDrxSwitch is
set to OFF.
In a DrxParaGroup
MO, the value of
OnDurationTimer
cannot be greater
than the value of
No (And no impact
ShortDrxCycle if
SupportShortDrx
mode)
is set to
UU_ENABLE.
If the ShortDrxCycle
parameter is set,
the value of
LongDrxCycle must
be an integer
multiple of
ShortDrxCycle.
This parameter is
No (And no impact
invalid when
EnterDrxSwitch is
mode)
set to OFF.
No (And no impact
mode)
No (And no impact
mode)
In an
InterRatHoComm
Group MO, the
value of
No (And no impact
InterRatHoA1ThdR
srp must be greater
mode)
value of
InterRatHoA2ThdR
srp.
In an
InterRatHoComm
Group MO, the
value of
No (And no impact
InterRatHoA1ThdR
srq must be greater
mode)
value of
InterRatHoA2ThdR
srq.
In an
InterRatHoComm
Group MO, the
value of
No (And no impact
InterRatHoA1ThdR
srp must be greater
mode)
value of
InterRatHoA2ThdR
srp.
In an
InterRatHoComm
Group MO, the
value of
No (And no impact
InterRatHoA1ThdR
srq must be greater
mode)
value of
InterRatHoA2ThdR
srq.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If coverage-based
handover is
enabled and the
threshold specified
higher than the
associated
threshold for
coverage-based
No (And no impact
inter-RAT handover,
coverage-based
mode)
handover takes
precedence over
both load- and
service-based
handovers. In this
case, load- and
service-based
handovers will not
occur.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If coverage-based
handover is
enabled and the
threshold specified
higher than the
associated
threshold for
coverage-based
No (And no impact
inter-RAT handover,
coverage-based
mode)
handover takes
precedence over
both load- and
service-based
handovers. In this
case, load- and
service-based
handovers will not
occur.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If the threshold
specified through
this parameter is
higher than the
associated
threshold for the
coverage-based
inter-RAT handover
and the coverage-
based handover is No (And no impact
enabled, the Read & Write on the UE in idle N/A N/A
coverage-based mode)
handover takes
precedence over
both the load- and
service-based
handovers. In this
case, the load- and
service-based
handovers would
not occur.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If coverage-based
handover is
enabled and the
threshold specified
higher than the
associated
threshold for
coverage-based
No (And no impact
inter-RAT handover,
coverage-based
mode)
handover takes
precedence over
both load- and
service-based
handovers. In this
case, load- and
service-based
handovers will not
occur.
If coverage-based
handover is
enabled and the
threshold specified
higher than the
associated
threshold for
coverage-based
No (And no impact
inter-RAT handover,
coverage-based
mode)
handover takes
precedence over
both load- and
service-based
handovers. In this
case, load- and
service-based
handovers will not
occur.
No (And no impact
mode)
No (And no impact
mode)
In an
InterFreqHoGroup
MO, the value of
InterFreqHoA1Thd
No (And no impact
Rsrp must be
greater than or
mode)
equal to the value
of
InterFreqHoA2Thd
Rsrp.
In an
InterFreqHoGroup
MO, the value of
InterFreqHoA1Thd
No (And no impact
Rsrq must be
greater than or
mode)
equal to the value
of
InterFreqHoA2Thd
Rsrq.
1. The value of
InterFreqHoA2Thd
Rsrp must be
smaller than that of
InterFreqHoA1Thd
Rsrp.
No (And no impact
2. In an
InterFreqHoGroup
mode)
MO, the value of
InterFreqHoA1Thd
Rsrp must be larger
than or equal to
InterFreqHoA2Thd
Rsrp.
1. The value of
InterFreqHoA2Thd
Rsrq must be
smaller than that of
InterFreqHoA1Thd
Rsrq.
No (And no impact
2. In an
InterFreqHoGroup
mode)
MO, the value of
InterFreqHoA1Thd
Rsrq must be larger
than or equal to
InterFreqHoA2Thd
Rsrq.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an
InterFreqHoGroup
MO, the value of
A3InterFreqHoA1T
No (And no impact
hdRsrp must be
greater than or
mode)
equal to the value
of
A3InterFreqHoA2T
hdRsrp.
In an
InterFreqHoGroup
MO, the value of
A3InterFreqHoA1T
No (And no impact
hdRsrp must be
greater than or
mode)
equal to the value
of
A3InterFreqHoA2T
hdRsrp.
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
The value of
CnOperatorName No (And no impact
in each Read & Write on the UE in idle N/A N/A
CnOperator MO mode)
must be unique.
CnOperatorType
can be set to
CNOPERATOR_PR Read & Write Yes eNodeB 3
IMARY in only one
CnOperator MO.
Mcc in each
CnOperator MO
must be numeric.
The combination of
Read & Write Yes eNodeB 3
Mcc and Mnc in
each CnOperator
MO must be
unique.
Mnc in each
CnOperator MO Read & Write Yes eNodeB 3
must be numeric.
No (And no impact
mode)
The combination of
CnOperatorId and
Tac in each Read & Write Yes Cell 0.1
CnOperatorTa MO
must be unique.
The combination of
CnOperatorId and
Tac in each Read & Write Yes Cell 0.1
CnOperatorTa MO
must be unique.
No (And no impact
mode)
This parameter is
No (And no impact
valid when
EmcEnable is set to
mode)
ON.
This parameter is
No (And no impact
valid when
EmcEnable is set to
mode)
ON.
This parameter is
No (And no impact
valid when
EmcEnable is set to
mode)
ON.
None Read & Write Yes eNodeB 3
The sum of
MaxUserNumRate
No (And no impact
in all
LicenseSharingPo
mode)
licy MOs cannot
exceed 100.
In the
S1ReestTimer MO,
the value of No (And no impact
S1ReestMinTimer Read & Write on the UE in idle N/A N/A
must be less than mode)
or equal to that of
S1ReestMaxTimer.
In the
S1ReestTimer MO,
the value of No (And no impact
S1ReestMinTimer Read & Write on the UE in idle N/A N/A
must be less than mode)
or equal to that of
S1ReestMaxTimer.
The S1SctpLinkId
value in each
Read & Write Yes Cell 0.1
S1Interface MO
must be unique.
None Read & Write Yes Cell 0.1
No (And no impact
mode)
No (After an S1
interface is blocked,
None Read & Write UEs in idle mode N/A N/A
cannot access the
network.)


No (And no impact
mode)
Mcc in an
X2BlackWhiteList
MO consists of
digits only.
Mnc in an
X2BlackWhiteList
MO consists of
digits only.

No (And no impact
mode)
The X2SctpLinkId
value in each
Read & Write Yes eNodeB 0.1
X2Interface MO
must be unique.
None Read & Write Yes eNodeB 0.1
None Read & Write Yes eNodeB 0.1

No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
In the Drx MO, the
value of
OnDurationTimerS No (And no impact
pecial cannot be Read & Write on the UE in idle N/A N/A
greater than that of mode)
LongDrxCycleSpe
cial.
In the Drx MO, the
value of
OnDurationTimerS
pecial cannot be
greater than that of
LongDrxCycleSpe
cial.
In the Drx MO, the
No (And no impact
value of
OnDurationTimerS
mode)
pecial cannot be
greater than the
value of
ShortDrxCycleSpe
cial if
SupportShortDrxS
pecial is set to
UU_ENABLE.
No (And no impact
mode)
No (And no impact
mode)
In the Drx MO, the
value of
OnDurationTimerS
pecial cannot be
greater than the
value of
ShortDrxCycleSpe
cial if
SupportShortDrxS
No (And no impact
pecial is set to
UU_ENABLE.
mode)
In the Drx MO, the
value of
LongDrxCycle
must be an integer
multiple of
ShortDrxCycle if
SupportShortDrxS
pecial is set to
UU_ENABLE.
This parameter is
available when No (And no impact
SupportShortDrxSp Read & Write on the UE in idle N/A N/A
ecial is set to mode)
UU_ENABLE.
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
set to
REDIRECTION for No (And no impact
a bearer with a QCI Read & Write on the UE in idle N/A N/A
of 1, call drop mode)
occurs during a
redirection.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_UM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_UM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_UM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_UM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_UM.
This parameter is
No (And no impact
valid when RlcMode
is set to
mode)
RlcMode_AM.
This parameter is No (And no impact

valid only for QCIs Read & Write on the UE in idle N/A N/A
6 to 9. mode)

6 to 9. mode)
6 to 9. mode)
6 to 9. mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
This parameter is
No (And no impact
valid only for QCIs
2 to 4 and QCIs 6
mode)
to 9.
6 to 9. mode)

5 to 9. mode)
No (And no impact
mode)
This parameter is
valid only when the No (And no impact
beamforming Read & Write on the UE in idle N/A N/A
algorithm is mode)
enabled.
This parameter is
BfMimoAdaptiveSwi Read & Write on the UE in idle N/A N/A
tch is set to mode)
NO_ADAPTIVE.
No (And no impact
mode)
No (And no impact
mode)
This parameter is
valid only when the No (And no impact
beamforming Read & Write on the UE in idle N/A N/A
algorithm is mode)
disabled.
This parameter is
MimoAdaptiveSwitc Read & Write on the UE in idle N/A N/A
h is set to mode)
NO_ADAPTIVE.
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
This parameter is
No (And no impact
available when
SMeasureInd is set
mode)
to CFG.
No (And no impact
mode)
This parameter is
No (And no impact
available when
SpeedDepParaInd
mode)
is set to CFG.
This parameter is
No (And no impact
available when
SpeedDepParaInd
mode)
is set to CFG.
In the
HoMeasComm
MO, if
SpeedDepParaInd
No (And no impact
is set to CFG,
NcrHighConnMod
mode)
e must be greater
than
NcrMediumConnM
ode.
In the
HoMeasComm
MO, if
SpeedDepParaInd
No (And no impact
is set to CFG,
NcrHighConnMod
mode)
e must be greater
than
NcrMediumConnM
ode.
This parameter is
No (And no impact
available when
SpeedDepParaInd
mode)
is set to CFG.
This parameter is
No (And no impact
available when
SpeedDepParaInd
mode)
is set to CFG.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (For the UE in
idle mode, this
parameter is used
with other
None Read & Write N/A N/A
parameters related
to cell access
barring to control
the UE accesses.)
AcBarringForEmerg No (Modifications
ency is optional, on this parameter
depending on the will affect the
Read & Write N/A N/A
setting of emergency call that
AcBarringInfoCfgIn is made by the UE
d. in idle mode.)
No (The access
request of the
AcBarringForMoDat mobile-originated
aCfgInd is optional, call initiated by a
depending on the UE in idle mode is
setting of accepted or
AcBarringInfoCfgIn rejected according
d. to the
corresponding
barring status.)
No (For the UE in
idle mode, the
AcBarringFactorFor source call
Call is optional, accesses are
depending on the allowed only when
setting of the random number
AcBarringForMoDat generated by the
aCfgInd. UE is smaller than
the access
probability factor.)
AcBarTimeForCall
is optional,
No (And no impact
depending on the
setting of
mode)
AcBarringForMoDat
aCfgInd.
No (For the UE in
AC11BarforCall is idle mode, if this
optional, depending parameter is set to
on the setting of Read & Write BOOLEAN_TRUE, N/A N/A
AcBarringForMoDat UEs of access class
aCfgInd. 11 are not allowed
to initiate calls.)
No (For the UE in
idle mode, if this
AC12BarforCall is parameter is set to
optional, depending BOOLEAN_TRUE,
on the setting of Read & Write the mobile- N/A N/A
AcBarringForMoDat originated calls
aCfgInd. initiated by UEs of
access class 12 are
not allowed.)
No (For the UE in
idle mode, if this
access class 13 are
not allowed.)
No (For the UE in
idle mode, if this
access class 14 are
not allowed.)
No (For the UE in
idle mode, if this
access class 15 are
not allowed.)
No (The access
request of the
AcBarringForMoSig
signaling initiated
CfgInd is optional,
by a UE in idle
depending on the
Read & Write mode is accepted N/A N/A
setting of
or rejected
AcBarringInfoCfgIn
according to the
d.
corresponding
barring status.)
No (The signaling
initiated by a UE in
AcBarringFactorFor
idle mode is
Sig is optional,
granted access only
depending on the
Read & Write when the random N/A N/A
setting of
number generated
AcBarringForMoSig
by the UE is smaller
CfgInd.
than the access
probability factor.)
AcBarTimeForSig is
optional, depending No (And no impact
on the setting of Read & Write on the UE in idle N/A N/A
AcBarringForMoSig mode)
CfgInd.
No (For the UE in
idle mode, if this
AC11BarForSig is
parameter is set to
optional, depending
BOOLEAN_TRUE,
on the setting of Read & Write N/A N/A
the signaling
AcBarringForMoSig
access initiated by
CfgInd.
UEs of access class
11 are not allowed.)
No (For the UE in
idle mode, if this
AC12BarForSig is
parameter is set to
optional, depending
BOOLEAN_TRUE,
the signaling
AcBarringForMoSig
access initiated by
CfgInd.
UEs of access class
No (For the UE in
idle mode, if this
AC13BarForSig is
parameter is set to
optional, depending
BOOLEAN_TRUE,
the signaling
AcBarringForMoSig
access initiated by
CfgInd.
UEs of access class
No (For the UE in
idle mode, if this
AC14BarForSig is
parameter is set to
optional, depending
BOOLEAN_TRUE,
the signaling
AcBarringForMoSig
access initiated by
CfgInd.
UEs of access class
No (For the UE in
idle mode, if this
AC15BarForSig is
parameter is set to
optional, depending
BOOLEAN_TRUE,
the signaling
AcBarringForMoSig
access initiated by
CfgInd.
UEs of access class
No (Modifications
on this parameter
None Read & Write will affect the cell on N/A N/A
which the UE in idle
mode camps.)
No (And no impact
mode)
No (Modifications
on this parameter
None Read & Write will affect the cell on N/A N/A
which the UE in idle
mode camps.)
No (And no impact
mode)
No (And no impact
mode)


The sum of
OpUlRbUsedRatio
in all CellOp MOs Read & Write Yes Cell 0.1
of the same cell
cannot exceed 100.
The sum of
OpDlRbUsedRatio
in all CellOp MOs Read & Write Yes Cell 0.1
of the same cell
cannot exceed 100.

No (Modifications
on this parameter
None Read & Write would affect cell N/A N/A
reselection of the
UE in idle mode.)
If
SpeedDepReselCfg
Ind is set to CFG,
the following
parameters must be
set: TEvaluation,
THystNormal,
NCellChangeMediu
m,
NCellChangeHigh,
QHystSfMedium
No (Modifications
and QHystSfHigh.
on this parameter
If
Read & Write would affect cell N/A N/A
SpeedDepReselCfg
reselection of the
Ind is set to
UE in idle mode.)
NOT_CFG, the
following
parameters do not
need to be set:
TEvaluation,
THystNormal,
NCellChangeMediu
m,
NCellChangeHigh,
QHystSfMedium
and QHystSfHigh.
This parameter is
optional, depending
on the setting of
SpeedDepReselCfg
Ind.
If
No (Modifications
SpeedDepReselCfg
on this parameter
Ind is set to CFG,
TEvaluation must
reselection of the
be set.
UE in idle mode.)
If
SpeedDepReselCfg
Ind is set to
NOT_CFG,
TEvaluation does
not need to be set.
This parameter is
optional, depending
on the setting of
SpeedDepReselCfg
Ind.
If
No (Modifications
SpeedDepReselCfg
on this parameter
Ind is set to CFG,
THystNormal must
reselection of the
be set.
UE in idle mode.)
If
SpeedDepReselCfg
Ind is set to
NOT_CFG,
THystNormal does
not need to be set.
In the CellResel
MO, if
SpeedDepReselCf No (Modifications
gInd is set to CFG, on this parameter
NCellChangeHigh Read & Write would affect cell N/A N/A
must be greater reselection of the
than UE in idle mode.)
NCellChangeMedi
um.
In the CellResel
MO, if
SpeedDepReselCf No (Modifications
NCellChangeHigh Read & Write would affect cell N/A N/A
must be greater reselection of the
than UE in idle mode.)
NCellChangeMedi
um.
This parameter is
optional, depending
on the setting of
SpeedDepReselCfg
Ind.
If
SpeedDepReselCfg No (Modifications
Ind is set to CFG, on this parameter
QHystSfMedium Read & Write would affect cell N/A N/A
must be set. reselection of the
If UE in idle mode.)
SpeedDepReselCfg
Ind is set to
NOT_CFG,
QHystSfMedium
does not need to be
set.
This parameter is
optional, depending
on the setting of
SpeedDepReselCfg
Ind.
If
No (Modifications
SpeedDepReselCfg
on this parameter
Ind is set to CFG,
QHystSfHigh must
reselection of the
be set.
UE in idle mode.)
If
SpeedDepReselCfg
Ind is set to
NOT_CFG,
QHystSfHigh does
not need to be set.
If
SNonIntraSearchCf
gInd is set to CFG,
SNonIntraSearch
No (Modifications
must be set.
on this parameter
If
SNonIntraSearchCf
reselection of the
gInd is set to
UE in idle mode.)
NOT_CFG,
SNonIntraSearch
does not need to be
set.
This parameter is
optional, depending
on the setting of
SNonIntraSearchCf
gInd.
If
SNonIntraSearchCf No (Modifications
SNonIntraSearch Read & Write would affect cell N/A N/A
needs to be set. reselection of the
SNonIntraSearchCf
gInd is set to
NOT_CFG,
SNonIntraSearch
does not need to be
set.
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
None Read & Write will affect cell N/A N/A
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
If PMaxCfgInd is
set to CFG, PMax No (Modifications
must be set. on this parameter
If PMaxCfgInd is Read & Write would affect cell N/A N/A
set to NOT_CFG, reselection of the
PMax does not UE in idle mode.)
need to be set.
This parameter is
optional, depending
on the setting of
PMaxCfgInd. No (Modifications
If PMaxCfgInd is on this parameter
set to CFG, PMax Read & Write would affect cell N/A N/A
If PMaxCfgInd is UE in idle mode.)
set to NOT_CFG,
PMax does not
need to be set.
If
SIntraSearchCfgInd
is set to CFG,
No (Modifications
SIntraSearch must
on this parameter
be set.
If
reselection of the
SIntraSearchCfgInd
UE in idle mode.)
is set to NOT_CFG,
SIntraSearch does
not need to be set.
This parameter is
optional, depending
on the setting of
SIntraSearchCfgInd
.
If No (Modifications
SIntraSearchCfgInd on this parameter
is set to CFG, Read & Write would affect cell N/A N/A
SIntraSearch needs reselection of the
to be set. UE in idle mode.)
If
SIntraSearchCfgInd
is set to NOT_CFG,
SIntraSearch does
not need to be set.
If
MeasBandWidthCfg
Ind is set to CFG,
MeasBandWidth
No (Modifications
must be set.
on this parameter
If
MeasBandWidthCfg
reselection of the
Ind is set to
UE in idle mode.)
NOT_CFG,
MeasBandWidth
does not need to be
set.
This parameter is
optional, depending
on the setting of
MeasBandWidthCfg
Ind.
If
MeasBandWidthCfg No (Modifications
MeasBandWidth Read & Write would affect cell N/A N/A
MeasBandWidthCfg
Ind is set to
NOT_CFG,
MeasBandWidth
does not need to be
set.
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
If
SpeedStateSfCfgIn
d is set to CFG, the
following
parameters must be
set:
TReselEutranSfMe
dium and
TReselEutranSfHig No (Modifications
h. on this parameter
If Read & Write would affect cell N/A N/A
SpeedStateSfCfgIn reselection of the
d is set to UE in idle mode.)
NOT_CFG, the
following
parameters do not
need to be set:
TReselEutranSfMe
dium and
TReselEutranSfHig
h.
This parameter is
optional, depending
on the setting of
SpeedStateSfCfgIn
d.
If
SpeedStateSfCfgIn No (Modifications
d is set to CFG, on this parameter
TReselEutranSfMe Read & Write would affect cell N/A N/A
dium must be set. reselection of the
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselEutranSfMe
dium does not need
to be set.
This parameter is
optional, depending
SpeedStateSfCfgIn
d parameter.
If
TReselEutranSfHig Read & Write would affect cell N/A N/A
h must be set. reselection of the
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselEutranSfHig
h does not need to
be set.
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
If
ThrshServLowQCfg
Ind is set to CFG,
this parameter must No (Modifications
be set. on this parameter
ThrshServLowQCfg reselection of the
Ind is set to UE in idle mode.)
NOT_CFG, this
parameter does not
need to be set
This parameter is
optional, depending
on the setting of
ThrshServLowQCfg
Ind.
If
No (Modifications
ThrshServLowQCfg
on this parameter
Ind is set to CFG,
this parameter must
reselection of the
be set.
UE in idle mode.)
If
ThrshServLowQCfg
Ind is set to
NOT_CFG, this
parameter does not
need to be set
If QQualMinCfgInd
is set to CFG, this
No (Modifications
parameter must be
on this parameter
set.
If QQualMinCfgInd
reselection of the
is set to NOT_CFG,
UE in idle mode.)
this parameter does
not need to be set.
This parameter is
optional, depending
on the setting of
QQualMinCfgInd.
No (Modifications
If QQualMinCfgInd
on this parameter
is set to CFG, this
parameter must be
reselection of the
set.
UE in idle mode.)
If QQualMinCfgInd
is set to NOT_CFG,
this parameter does
not need to be set.
If SysTimeCfgInd is
set to CFG,
CdmaEutraSyn No (Modifications
must be set. on this parameter
If SysTimeCfgInd is Read & Write would affect cell N/A N/A
set to NOT_CFG, reselection of the
CdmaEutraSyn UE in idle mode.)
does not need to be
set.
This parameter is
optional, depending
on the setting of
SysTimeCfgInd.
If SysTimeCfgInd is No (Modifications
set to CFG, on this parameter
CdmaEutraSyn Read & Write would affect cell N/A N/A
If SysTimeCfgInd is UE in idle mode.)
set to NOT_CFG,
CdmaEutraSyn
does not need to be
set.
If
SearchWndSizeCfg
Ind is set to CFG,
SearchWndSize
No (Modifications
must be set.
on this parameter
If
SearchWndSizeCfg
reselection of the
Ind is set to
UE in idle mode.)
NOT_CFG,
SearchWndSize
does not need to be
set.
This parameter is
optional, depending
on the setting of
SearchWndSizeCfg
Ind.
If
SearchWndSizeCfg No (Modifications
SearchWndSize Read & Write would affect cell N/A N/A
SearchWndSizeCfg
Ind is set to
NOT_CFG,
SearchWndSize
does not need to be
set.
If HrpdParamCfgInd
is set to CFG, the
following
parameters must be
set:
HrpdPreRegistAllow
ed,
HrpdSecondPreRe
gistZoneId0Ind, and
No (Modifications
HrpdCellReselectP
on this parameter
aramCfgInd.
If HrpdParamCfgInd
reselection of the
is set to NOT_CFG,
UE in idle mode.)
the following
parameters do not
need to be set:
HrpdPreRegistAllow
ed,
HrpdSecondPreRe
gistZoneId0Ind, and
HrpdCellReselectP
aramCfgInd.
1. This parameter is
optional, depending
on the setting of
HrpdParamCfgInd.
If HrpdParamCfgInd
is set to CFG,
HrpdCellReselectP
aramCfgInd must
be set.
If HrpdParamCfgInd
is set to NOT_CFG,
HrpdCellReselectP
aramCfgInd does
not need to be set.
2 If
HrpdCellReselectP
No (Modifications
aramCfgInd is set
on this parameter
to CFG, the
following
reselection of the
parameters must be
UE in idle mode.)
set:
TreselectionHrpd
and
SpeedStateSfCfgIn
d.
If
HrpdCellReselectP
aramCfgInd is set
to NOT_CFG, the
following
parameters do not
need to be set:
TreselectionHrpd
and
SpeedStateSfCfgIn
d.
1. If
HrpdPreRegistAllow
ed is set to
BOOLEAN_TRUE,
HrpdPreRegistZone
Id must be set.
If
HrpdPreRegistAllow
ed is set to
BOOLEAN_FALSE,
HrpdPreRegistZone
No (Modifications
Id does not need to
on this parameter
be set.
reselection of the
optional, depending
UE in idle mode.)
on the setting of
HrpdParamCfgInd.
If HrpdParamCfgInd
is set to CFG,
HrpdPreRegistAllow
ed must be set.
If HrpdParamCfgInd
is set to NOT_CFG,
HrpdPreRegistAllow
ed does not need to
be set.
This parameter is
optional, depending
on the setting of
HrpdPreRegistAllow
ed.
If
HrpdPreRegistAllow
No (Modifications
ed is set to
on this parameter
BOOLEAN_TRUE,
HrpdPreRegistZone
reselection of the
Id must be set.
UE in idle mode.)
If
HrpdPreRegistAllow
ed is set to
BOOLEAN_FALSE,
HrpdPreRegistZone
Id does not need to
be set.
optional, depending
on the setting of
HrpdParamCfgInd.
If HrpdParamCfgInd
is set to CFG,
HprdSecondPreRe
gistZoneId0Ind
must be set.
If HrpdParamCfgInd
is set to NOT_CFG,
HprdSecondPreRe
gistZoneId0Ind
does not need to be
set.
2. If
HrpdSecondPreRe No (Modifications
gistZoneId0Ind is on this parameter
set to CFG, the Read & Write would affect cell N/A N/A
following reselection of the
parameters must be UE in idle mode.)
set:
HrpSecondPreRegi
stZoneId0 and
HrpdSecondPreRe
gistZoneId1Ind.
If
HrpdSecondPreRe
gistZoneId0Ind is
set to NOT_CFG,
the following
parameters do not
need to be set:
HrpdSecondPreRe
gistZoneId0 and
HrpdSecondPreRe
gistZoneId1Ind.
optional, depending
on the setting of
HprdSecondPreRe
gistZoneId0Ind.
If
HprdSecondPreRe
gistZoneId0Ind is No (Modifications
HprdSecondPreRe Read & Write would affect cell N/A N/A
gistZoneId0 must reselection of the
be set. UE in idle mode.)
If
HprdSecondPreRe
gistZoneId0Ind is
set to NOT_CFG,
HprdSecondPreRe
gistZoneId0 does
not need to be set.
optional, depending
on the setting of
HrpdSecondPreRe
gistZoneId0Ind.
If
HrpdSecondPreRe
gistZoneId0Ind is
set to CFG,
HrpdSecondPreRe
gistZoneId1Ind
must be set.
If
HrpdSecondPreRe
gistZoneId0Ind is
No (Modifications
set to NOT_CFG,
on this parameter
HrpdSecondPreRe
gistZoneId1Ind
reselection of the
does not need to be
UE in idle mode.)
set.
2. If
HrpdSecondPreRe
gistZoneId1Ind is
set to CFG,
HrpdSecondPreRe
gistZoneId1 must
be set.
If
HrpdSecondPreRe
gistZoneId1Ind is
set to NOT_CFG,
HrpdSecondPreRe
gistZoneId1 does
not need to be set.
This parameter is
optional, depending
on the setting of
HprdSecondPreRe
gistZoneId1Ind.
If
HprdSecondPreRe
gistZoneId1Ind is No (Modifications
HprdSecondPreRe Read & Write would affect cell N/A N/A
gistZoneId1 must reselection of the
be set. UE in idle mode.)
If
HprdSecondPreRe
gistZoneId1Ind is
set to NOT_CFG,
HprdSecondPreRe
gistZoneId1 does
not need to be set.
This parameter is
optional, depending
on the setting of
HrpdCellReselectP
aramCfgInd.
If
HrpdCellReselectP
No (Modifications
aramCfgInd is set
on this parameter
to CFG,
TreselectionHrpd
reselection of the
must be set.
UE in idle mode.)
If
HrpdCellReselectP
aramCfgInd is set
to NOT_CFG,
TreselectionHrpd
does not need to be
set.
optional, depending
on the setting of
HrpdCellReselectP
aramCfgInd.
If
HrpdCellReselectP
aramCfgInd is set
to CFG,
SpeedStateSfCfgIn
d must be set.
If
HrpdCellReselectP
aramCfgInd is set
to NOT_CFG,
SpeedStateSfCfgIn
d does not need to
be set. No (Modifications
2 If on this parameter
SpeedStateSfCfgIn Read & Write would affect cell N/A N/A
d is set to CFG, the reselection of the
following UE in idle mode.)
parameters must be
set:
TReselCdmaHrpdSf
Medium and
TReselCdmaHrpdSf
High.
If
SpeedStateSfCfgIn
d is set to
NOT_CFG, the
following
parameters do not
need to be set:
TReselCdmaHrpdSf
Medium and
TReselCdmaHrpdSf
This parameter is
optional, depending
on the setting of
SpeedStateSfCfgIn
d.
If
TReselCdmaHprdSf Read & Write would affect cell N/A N/A
High must be set. reselection of the
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselCdmaHprdSf
High does not need
to be set.
This parameter is
optional, depending
on the setting of
SpeedStateSfCfgIn
d.
If
SpeedStateSfCfgIn
No (Modifications
d is set to CFG,
on this parameter
TReselCdmaHrpdSf
Medium must be
reselection of the
set.
UE in idle mode.)
If
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselCdmaHrpdSf
Medium does not
need to be set.
If Cdma1XrttCfgInd
is set to CFG, the
following
parameters must be
set:
Cdma1XrttCsfbReg
CfgInd,
Cdma1XrttLongCod
eStateCfgInd, and
No (Modifications
Cdma1XrttCellRese
on this parameter
lCfgInd.
If Cdma1XrttCfgInd
reselection of the
is set to NOT_CFG,
UE in idle mode.)
the following
parameters do not
need to be set:
Cdma1XrttCsfbReg
CfgInd,
Cdma1XrttLongCod
eStateCfgInd, and
Cdma1XrttCellRese
lCfgInd.
MultiSidInd,
Cdma1XrttCsfbReg
MultiNidInd,
Cdma1XrttCsfbReg
HomeRegInd,
Cdma1XrttCsfbReg
ForeignSidRegInd,
Cdma1XrttCsfbReg
ForeignNidRegInd,
Cdma1XrttCsfbReg
ParamRegInd,
Cdma1XrttCsfbReg
PowerUpRegInd,
Cdma1XrttCsfbReg
RegPeriod,
Cdma1XrttCsfbReg
RegZone, No (Modifications
Cdma1XrttCsfbReg on this parameter
TotalZone, Read & Write will affect cell N/A N/A
Cdma1XrttCsfbReg reselection of the
ZoneTimer, UE in idle mode.)
Cdma1XrttCsfbPwr
DownRegInd, and
Cdma1XrttCsfbAcB
arCfgInd.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG, the
preceding
parameters do not
need to be set.
2.
Cdma1XrttCsfbReg
CfgInd is optional,
depending on the
setting of
This parameter is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Cdma1XrttCsfbReg
reselection of the
Sid must be set.
UE in idle mode.)
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
Sid does not need
to be set.
This parameter is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Cdma1XrttCsfbReg
reselection of the
Nid must be set.
UE in idle mode.)
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
Nid does not need
to be set.
Cdma1XrttCsfbReg
MultiSidInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Cdma1XrttCsfbReg
reselection of the
MultiSidInd must be
UE in idle mode.)
set.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
MultiSidInd does
not need to be set.
Cdma1XrttCsfbReg
MultiNidInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Cdma1XrttCsfbReg
reselection of the
MultiNidInd must be
UE in idle mode.)
set.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
MultiNidInd does
not need to be set.
Cdma1XrttCsfbReg
HomeRegInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Cdma1XrttCsfbReg
reselection of the
HomeRegInd must
UE in idle mode.)
be set.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
HomeRegInd does
not need to be set.
Cdma1XrttCsfbReg
FrgnSidRegInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
CfgInd is set to No (Modifications
CFG, on this parameter
Cdma1XrttCsfbReg Read & Write would affect cell N/A N/A
FrgnSidRegInd reselection of the
must be set. UE in idle mode.)
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
FrgnSidRegInd
does not need to be
set.
Cdma1XrttCsfbReg
FrgnNidRegInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
FrgnNidRegInd reselection of the
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
FrgnNidRegInd
does not need to be
set.
Cdma1XrttCsfbReg
ParamRegInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Cdma1XrttCsfbReg
reselection of the
ParamRegInd must
UE in idle mode.)
be set.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
ParamRegInd does
not need to be set.
Cdma1XrttCsfbReg
PowerUpRegInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
PowerUpRegInd reselection of the
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
PowerUpRegInd
does not need to be
set.
This parameter is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
RegPeriod must be reselection of the
set. UE in idle mode.)
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
RegPeriod does not
need to be set.
This parameter is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
RegZone must be reselection of the
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
RegZone does not
need to be set.
This parameter is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
TotalZone must be reselection of the
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
TotalZone does not
need to be set.
This parameter is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
ZoneTimer must be reselection of the
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
Cdma1XrttCsfbReg
ZoneTimer does not
need to be set.
1. If
Cdma1XrttLongCod
eStateCfgInd is set
to CFG,
Cdma1XrttLongCod
eState must be set.
If
Cdma1XrttLongCod
eStateCfgInd is set
to NOT_CFG,
Cdma1XrttLongCod
eState does not
need to be set. No (Modifications
2. on this parameter
Cdma1XrttLongCod Read & Write would affect cell N/A N/A
eStateCfgInd is reselection of the
optional, depending UE in idle mode.)
on the setting of
Cdma1XrttCfgInd.
If Cdma1XrttCfgInd
is set to CFG,
Cdma1XrttLongCod
eStateCfgInd must
be set.
If Cdma1XrttCfgInd
is set to NOT_CFG,
Cdma1XrttLongCod
eStateCfgInd does
not need to be set.
This parameter is
optional, depending
on the setting of
Cdma1XrttLongCod
eStateCfgInd.
If
Cdma1XrttLongCod
No (Modifications
eStateCfgInd is set
on this parameter
to CFG,
Cdma1XrttLongCod
reselection of the
eState must be set.
UE in idle mode.)
If
Cdma1XrttLongCod
eStateCfgInd is set
to NOT_CFG,
Cdma1XrttLongCod
eState does not
need to be set.
1.
Cdma1XrttCellRese
lCfgInd is optional,
depending on the
setting of
Cdma1XrttCfgInd.
If Cdma1XrttCfgInd
is set to CFG,
Cdma1XrttCellRese
lCfgInd must be set.
If Cdma1XrttCfgInd
is set to NOT_CFG,
Cdma1XrttCellRese
lCfgInd does not
need to be set.
2. If
No (Modifications
Cdma1XrttCellRese
on this parameter
lCfgInd is set to
CFG, the following
reselection of the
parameters must be
UE in idle mode.)
set:
Cdma1XrttTreselect
ion and
Cdma1XrttSpeedSt
ateCfgInd.
If
Cdma1XrttCellRese
lCfgInd is set to
NOT_CFG, the
following
parameters do not
need to be set:
Cdma1XrttTreselect
ion and
Cdma1XrttSpeedSt
ateCfgInd.
This parameter is
optional, depending
on the setting of
Cdma1XrttCellRese
lCfgInd.
If
Cdma1XrttCellRese
No (Modifications
lCfgInd is set to
on this parameter
CFG,
Cdma1XrttTreselect
reselection of the
ion must be set.
UE in idle mode.)
If
Cdma1XrttCellRese
lCfgInd is set to
NOT_CFG,
Cdma1XrttTreselect
ion does not need
to be set.
Cdma1XrttSpeedSt
ateCfgInd is
optional, depending
on the setting of
Cdma1XrttCellRese
lCfgInd.
If
Cdma1XrttCellRese
lCfgInd is set to
CFG,
Cdma1XrttSpeedSt
ateCfgInd must be
set.
If
Cdma1XrttCellRese
lCfgInd is set to
NOT_CFG,
No (Modifications
Cdma1XrttSpeedSt
on this parameter
ateCfgInd does not
need to be set.
reselection of the
2. If
UE in idle mode.)
Cdma1XrttSpeedSt
ateCfgInd is set to
CFG, the following
parameters must be
set:
Cdma1XrttSfMediu
m and
Cdma1XrttSfHigh.
If
Cdma1XrttSpeedSt
ateCfgInd is set to
NOT_CFG, the
following
parameters do not
need to be set:
Cdma1XrttSfMediu
m and
This parameter is
optional, depending
on the setting of
Cdma1XrttSpeedSt
ateCfgInd.
If
Cdma1XrttSpeedSt
No (Modifications
ateCfgInd is set to
on this parameter
CFG,
Cdma1XrttSfMediu
reselection of the
m must be set.
UE in idle mode.)
If
Cdma1XrttSpeedSt
ateCfgInd is set to
NOT_CFG,
Cdma1XrttSfMediu
m does not need to
be set.
This parameter is
optional. Whether
to set this
parameter is
determined by the
parameter
Cdma1XrttSpeedSt
ateCfgInd.
When No (Modifications
Cdma1XrttSpeedSt on this parameter
ateCfgInd is set to Read & Write would affect cell N/A N/A
CFG, reselection of the
Cdma1XrttSfHigh UE in idle mode.)
needs to be set.
When
Cdma1XrttSpeedSt
ateCfgInd is set to
NOT_CFG,
Cdma1XrttSfHigh
does not need to be
set.
CsfbRegPwrDownR
egCfgInd is
optional, depending
on the setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
No (Modifications
CfgInd is set to
on this parameter
CFG,
Read & Write will affect cell N/A N/A
CsfbRegPwrDownR
reselection of the
egCfgInd needs to
UE in idle mode.)
be set.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
CsfbRegPwrDownR
egCfgInd does not
need to be set.
is optional,
depending on the
setting of
Cdma1XrttCsfbReg
CfgInd.
If
Cdma1XrttCsfbReg
CfgInd is set to
CFG,
CsfbAcBarCfgInd
needs to be set.
If
Cdma1XrttCsfbReg
CfgInd is set to
NOT_CFG,
CsfbAcBarCfgInd
does not need to be
No (Modifications
set.
on this parameter
2. If
CsfbAcBarCfgInd is
reselection of the
set to CFG, the
UE in idle mode.)
following
parameters need to
be set:
CsfbAcBar0to9,
CsfbAcBar10,
CsfbAcBar11,
CsfbAcBar12,
CsfbAcBar13,
CsfbAcBar14,
CsfbAcBar15,
CsfbAcBarMsg,
CsfbAcBarReg, and
CsfbAcBarEmg.
If CsfbAcBarCfgInd
is set to NOT_CFG,
the preceding
parameters do not
CsfbAcBar0to9 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
If CsfbAcBarCfgInd No (Modifications
is set to CFG, on this parameter
CsfbAcBar0to9 Read & Write will affect cell N/A N/A
If CsfbAcBarCfgInd UE in idle mode.)
is set to NOT_CFG,
CsfbAcBar0to9
does not need to be
set.
CsfbAcBar10 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
No (Modifications
If CsfbAcBarCfgInd
on this parameter
is set to CFG,
CsfbAcBar10 needs
reselection of the
to be set.
UE in idle mode.)
If CsfbAcBarCfgInd
is set to NOT_CFG,
CsfbAcBar10 does
not need to be set.
CsfbAcBar11 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
No (Modifications
If CsfbAcBarCfgInd
on this parameter
is set to CFG,
CsfbAcBar11 needs
reselection of the
to be set.
UE in idle mode.)
If CsfbAcBarCfgInd
is set to NOT_CFG,
CsfbAcBar11 does
not need to be set.
CsfbAcBar12 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
No (Modifications
If CsfbAcBarCfgInd
on this parameter
is set to CFG,
CsfbAcBar12 needs
reselection of the
to be set.
UE in idle mode.)
If CsfbAcBarCfgInd
is set to NOT_CFG,
CsfbAcBar12 does
not need to be set.
CsfbAcBar13 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
No (Modifications
If CsfbAcBarCfgInd
on this parameter
is set to CFG,
CsfbAcBar13 needs
reselection of the
to be set.
UE in idle mode.)
If CsfbAcBarCfgInd
is set to NOT_CFG,
CsfbAcBar13 does
not need to be set.
CsfbAcBar14 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
No (Modifications
If CsfbAcBarCfgInd
on this parameter
is set to CFG,
CsfbAcBar14 needs
reselection of the
to be set.
UE in idle mode.)
If CsfbAcBarCfgInd
is set to NOT_CFG,
CsfbAcBar14 does
not need to be set.
CsfbAcBar15 is
optional, depending
on the setting of
CsfbAcBarCfgInd.
No (Modifications
If CsfbAcBarCfgInd
on this parameter
is set to CFG,
CsfbAcBar15 needs
reselection of the
to be set.
UE in idle mode.)
If CsfbAcBarCfgInd
is set to NOT_CFG,
CsfbAcBar15 does
not need to be set.
CsfbAcBarMsg is
optional, depending
on the setting of
CsfbAcBarCfgInd.
CsfbAcBarMsg Read & Write will affect cell N/A N/A
is set to NOT_CFG,
CsfbAcBarMsg
does not need to be
set.
CsfbAcBarReg is
optional, depending
on the setting of
CsfbAcBarCfgInd.
CsfbAcBarReg Read & Write will affect cell N/A N/A
is set to NOT_CFG,
CsfbAcBarReg
does not need to be
set.
CsfbAcBarEmg is
optional, depending
on the setting of
CsfbAcBarCfgInd.
CsfbAcBarEmg Read & Write will affect cell N/A N/A
is set to NOT_CFG,
CsfbAcBarEmg
does not need to be
set.

No (Modifications
on this parameter
reselection of the
UE in idle mode.)
If
SpeedStateSfCfgIn
following
parameters must be
set:
TReselGeranSfMed
ium and
TReselGeranSfHigh No (Modifications
. on this parameter
NOT_CFG, the
following
parameters do not
need to be set:
TReselGeranSfMed
ium and
TReselGeranSfHigh
.
This parameter is
optional, depending
on the setting of
SpeedStateSfCfgIn
d.
If
TReselGeranSfMed Read & Write would affect cell N/A N/A
ium must be set. reselection of the
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselGeranSfMed
ium does not need
to be set.
This parameter is
optional, depending
on the setting of
SpeedStateSfCfgIn
d.
If
TReselGeranSfHigh Read & Write would affect cell N/A N/A
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselGeranSfHigh
does not need to be
set.

No (Modifications
on this parameter
reselection of the
UE in idle mode.)
If
SpeedStateSfCfgIn
following
parameters must be
set:
TReselUtranSfMedi
um and No (Modifications
TReselUtranSfHigh. on this parameter
NOT_CFG, the
following
parameters do not
need to be set:
TReselUtranSfMedi
um and
TReselUtranSfHigh.
This parameter is
optional, depending
SpeedStateSfCfgIn
d parameter.
If
TReselUtranSfMedi Read & Write would affect cell N/A N/A
um must be set. reselection of the
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselUtranSfMedi
um does not need
to be set.
This parameter is
optional, depending
SpeedStateSfCfgIn
d parameter.
If
TReselUtranSfHigh Read & Write would affect cell N/A N/A
SpeedStateSfCfgIn
d is set to
NOT_CFG,
TReselUtranSfHigh
does not need to be
set.

No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
selection of the UE
in idle mode.)
set to CFG, the No (Modifications
offset is required. If on this parameter
this parameter is Read & Write would affect cell N/A N/A
set to NOT_CFG, selection of the UE
the offset does not in idle mode.)
need to be set.
This parameter is
optional, depending
on the setting of
QQualMinOffsetCfg
Ind.
If
No (Modifications
QQualMinOffsetCfg
on this parameter
Ind is set to CFG,
this parameter must
selection of the UE
be set.
in idle mode.)
If
QQualMinOffsetCfg
Ind is set to
NOT_CFG, this
parameter does not
need to be set.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the Cell MO, the

value of CellName
is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters:double
No (And no impact
commas (,),
mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three plus
signs (+++), two or
more consecutive
spaces, and two or
more consecutive
percentage signs
(%).

CsgInd in a Cell
MO must be set to Read & Write Yes Cell 0.1
BOOLEAN_FALSE.
to SSP4, SSP5,
SSP6, or SSP7;
(2) If
UlCyclicPrefix and
DlCyclicPrefix are
both set to
EXTENDED_CP,
SpecialSubframeP
atterns can be set
to SSP3, SSP4,
SSP5, or SSP6;
(3) If
UlCyclicPrefix is
set to
EXTENDED_CP
and DlCyclicPrefix
is set to
NORMAL_CP,
SpecialSubframeP Read & Write Yes Cell 0.1
atterns can be set
to SSP4, SSP5,
SSP6, or SSP7;
(4) If
UlCyclicPrefix is
set to NORMAL_CP
and DlCyclicPrefix
is set to
EXTENDED_CP,
SpecialSubframeP
atterns can be set
to SSP3, SSP4,
SSP5, or SSP6.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
5M, UlCyclicPrefix
to SSP4, SSP5,
SSP6, or SSP7;
(2) If
UlCyclicPrefix and
DlCyclicPrefix are
both set to
EXTENDED_CP,
SpecialSubframeP
atterns can be set
to SSP3, SSP4,
SSP5, or SSP6;
(3) If
UlCyclicPrefix is
set to
EXTENDED_CP
and DlCyclicPrefix
is set to
NORMAL_CP,
SpecialSubframeP Read & Write Yes Cell 0.1
atterns can be set
to SSP4, SSP5,
SSP6, or SSP7;
(4) If
UlCyclicPrefix is
set to NORMAL_CP
and DlCyclicPrefix
is set to
EXTENDED_CP,
SpecialSubframeP
atterns can be set
to SSP3, SSP4,
SSP5, or SSP6.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
5M, UlCyclicPrefix
In a Cell MO,
DlEarfcn must be
set based on the
setting of
FreqBand. For
details, see 3GPP
TS 36.104.
In a Cell MO,
UlEarfcn must be
set based on the
setting of
FreqBand. For
details, see 3GPP
TS 36.104.
In a Cell MO, if
FddTddInd is set to
TDD and
UlEarfcnCfgInd is
set to CFG, Read & Write Yes Cell 0.1
DlEarfcn and
UlEarfcn must be
set to the same
value.
In a Cell MO, if
FddTddInd is set to
TDD and
UlEarfcnCfgInd is
set to CFG,
DlEarfcn and
UlEarfcn must be
set to the same
value.
In a Cell MO,
UlEarfcn must be
set based on the
setting of
FreqBand. For
details, see 3GPP
TS 36.104.
In a Cell MO,
DlEarfcn must be
set based on the
setting of
FreqBand. For
details, see 3GPP
TS 36.104.
In a Cell MO, if
FddTddInd is set to
TDD and
UlEarfcnCfgInd is
set to CFG,
DlEarfcn and
UlEarfcn must be
set to the same
value.
dWidth must be set
to a value in the
range of 48 to 50;
If UlBandWidth is
set to
CELL_BW_N50,
CustomizedULBan
dWidth must be set
to a value in the
range of 96 to 100;
If UlBandWidth is
set to
CELL_BW_N75,
CustomizedULBan
dWidth must be set
to a value in the
range of 146 to
150;
If UlBandWidth is Read & Write Yes Cell 0.1
set to
CELL_BW_N100,
CustomizedULBan
dWidth must be set
to a value in the
range of 183 to
200.
When the
HighSpeedFlag in
Cell MO is not
EXTRA_HIGH_SPE
ED, DlBandWidth
and UlBandWidth
must be set to the
same value in each
Cell MO.
If MultiRruCellFlag
in a Cell MO is set
5M,
HighSpeedFlag is
not be
ULTRA_HIGH_SPE
ED.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
5M,
MultiRruCellFlag
must be set
BOOLEAN_FALSE.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
5M, UlCyclicPrefix
and DlCyclicPrefix
must be set
NORMAL_CP.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
5M,
CPRICompression
must be set
NO_COMPRESSIO
N.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
CELL_BW_N50 or
CELL_BW_N100,
CPRICompression
can be set to
CellId must have a

unique value in
each Cell MO Read & Write Yes Cell 0.1
under the same
eNodeB.
In a Cell MO, if
CustomizedBand
WidthCfgInd is set
to CFG and
CustomizedDLBan
dWidth is set to a
value in the range
of 183 to 192,
PhyCellId must be
set to a value in Read & Write Yes Cell 0.1
ranges: 8 to 41, 74
to 78, 108 to 110,
139 to 141, 158 to
175, 208 to 241,
270 to 274, 335 to
341, 358 to 371,
408 to 437, and 466
to 470.
No (And no impact
mode)
Until the cell is

None Read & Write Yes Cell
activated
Until the cell is
None Read & Write Yes Cell
unblocked
This parameter
needs to be No (And no impact
specified only when Read & Write on the UE in idle N/A N/A
the middle priority mode)
block is performed
PreambleFmt and
SubframeAssignm
ent:
(1) If PreambleFmt
is set to 0,
SubframeAssignm
ent can be set to
SA0, SA1, SA2,
SA3, or SA5;
(2) If PreambleFmt
is set to 1,
SubframeAssignm
ent can be set to
SA0, SA1, or SA3;
(3) If PreambleFmt
is set to 2,
SubframeAssignm
ent can be set to
SA0, SA1, or SA3;
(4) If PreambleFmt
is set to 3,
SubframeAssignm
ent can be set to
SA0 or SA3;
(5) If PreambleFmt
is set to 4,
SubframeAssignm
ent can be set to
SA0, SA1, SA2,
SA3, or SA5.
If MultiRruCellFlag
in a Cell MO is set
to
BOOLEAN_TRUE
and
MultiRruCellMode
in a Cell MO is set
to SFN, FddTddInd
SA0, SA1, SA2,
SA3, or SA5 if
FddTddInd is set to
TDD.
In a Cell MO, if
FddTddInd is set to
TDD, the following
requirements must
be met during the
setting of
PreambleFmt and
SubframeAssignm
ent:
(1) If PreambleFmt
is set to 0,
SubframeAssignm
ent can be set to
SA0, SA1, SA2,
SA3, or SA5; Read & Write Yes Cell 0.1
(2) If PreambleFmt
is set to 1,
SubframeAssignm
ent can be set to
SA0, SA1, or SA3;
(3) If PreambleFmt
is set to 2,
SubframeAssignm
ent can be set to
SA0, SA1, or SA3;
(4) If PreambleFmt
is set to 3,
SubframeAssignm
ent can be set to
SA0 or SA3;
(5) If PreambleFmt
is set to 4,
SubframeAssignm
(1) If
UlCyclicPrefix and
DlCyclicPrefix are
both set to
NORMAL_CP,
SpecialSubframeP
atterns can be set
to SSP4, SSP5,
SSP6, or SSP7;
(2) If
UlCyclicPrefix and
DlCyclicPrefix are
both set to
EXTENDED_CP,
SpecialSubframeP
atterns can be set
to SSP3, SSP4,
SSP5, or SSP6;
(3) If Read & Write Yes Cell 0.1
UlCyclicPrefix is
set to
EXTENDED_CP
and DlCyclicPrefix
is set to
NORMAL_CP,
SpecialSubframeP
atterns can be set
to SSP4, SSP5,
SSP6, or SSP7;
(4) If
UlCyclicPrefix is
set to NORMAL_CP
and DlCyclicPrefix
is set to
EXTENDED_CP,
SpecialSubframeP
atterns can be set
No (And no impact
mode)
No (And no impact
mode)
of 42 to 797;
(5) 2600 <
CellRadius <=
3500:
RootSequenceIdx
can be set to a
value in the range
of 52 to 786;
(6) 3500 <
CellRadius <=
4300:
RootSequenceIdx
can be set to a
value in the range
of 64 to 779;
(7) 4300 <
CellRadius <=
5500:
RootSequenceIdx
can be set to a
value in the range
of 76 to 765;
(8) 5500 <
CellRadius <=
6800:
RootSequenceIdx
can be set to a
value in the range
of 90 to 747;
(9) 6800 <
CellRadius <=
8600:
RootSequenceIdx
can be set to a
value in the range
of 116 to 731;
(10) 8600 <
CellRadius <=
CellRadius <=
5500:
RootSequenceIdx
can be set to a
value in the range
of 76 to 765;
(8) 5500 <
CellRadius <=
6800:
RootSequenceIdx
can be set to a
value in the range
of 90 to 747;
(9) 6800 <
CellRadius <=
8600:
RootSequenceIdx
can be set to a
value in the range
of 116 to 731;
(10) 8600 <
CellRadius <=
10600:
RootSequenceIdx
can be set to a
value in the range
of 136 to 706;
(11) 10600 <
CellRadius <=
13200:
RootSequenceIdx
can be set to a
value in the range
of 168 to 676;
(12) 13200 <
CellRadius <=
17200:
RootSequenceIdx
HIGH_SPEED or
ULTRA_HIGH_SPE
ED, the following
requirements must
be met during the
setting of
CellRadius and
RootSequenceIdx:
(1) 1 <= CellRadius
<= 1000:
RootSequenceIdx
can be set to a
value in the range
of 24 to 815;
(2) 1000 <
CellRadius <=
1500:
RootSequenceIdx
can be set to a
value in the range
of 30 to 811;
(3). 1500 <
CellRadius <=
2000:
RootSequenceIdx
can be set to a
value in the range
of 36 to 804;
(4) 2000 <
CellRadius <=
2600:
RootSequenceIdx
can be set to a
value in the range
of 42 to 797;
(5) 2600 <
CellRadius <=
3500:
2600:
RootSequenceIdx
can be set to a
value in the range
of 42 to 797;
(5) 2600 <
CellRadius <=
3500:
RootSequenceIdx
can be set to a
value in the range
of 52 to 786;
(6) 3500 <
CellRadius <=
4300:
RootSequenceIdx
can be set to a
value in the range
of 64 to 779; Read & Write Yes Cell 0.1
(7) 4300 <
CellRadius <=
5500:
RootSequenceIdx
can be set to a
value in the range
of 76 to 765;
(8) 5500 <
CellRadius <=
6800:
RootSequenceIdx
can be set to a
value in the range
of 90 to 747;
(9) 6800 <
CellRadius <=
8600:
RootSequenceIdx
to CFG:
If UlBandWidth is
set to
CELL_BW_N25,
CustomizedULBan
dWidth must be set
to a value in the
range of 48 to 50;
If UlBandWidth is
set to
CELL_BW_N50,
CustomizedULBan
dWidth must be set
to a value in the
range of 96 to 100;
If UlBandWidth is
set to
CELL_BW_N75,
CustomizedULBan
dWidth must be set
to a value in the
range of 146 to
150;
If UlBandWidth is
set to
CELL_BW_N100,
CustomizedULBan
dWidth must be set
to a value in the
range of 183 to
200.
In a Cell MO, when
CustomizedBand
WidthCfgInd is set
to CFG:
If DlBandWidth is
set to
CELL_BW_N25,
to CFG:
If UlBandWidth is
set to
CELL_BW_N25,
CustomizedULBan
dWidth must be set
to a value in the
range of 48 to 50;
If UlBandWidth is
set to
CELL_BW_N50,
CustomizedULBan
dWidth must be set
to a value in the
range of 96 to 100;
If UlBandWidth is
set to
CELL_BW_N75,
CustomizedULBan
dWidth must be set
to a value in the
range of 146 to
150;
If UlBandWidth is
set to
CELL_BW_N100,
CustomizedULBan
dWidth must be set
to a value in the
range of 183 to
200.
In a Cell MO, if
CustomizedBand
WidthCfgInd is set
to CFG,
CustomizedULBan
dWidth and
CustomizedDLBan
In a Cell MO, if
CustomizedBand
WidthCfgInd is set
to CFG and
CustomizedDLBan
dWidth is set to a
value in the range
of 183 to 192,
PhyCellId must be
set to a value in
ranges: 8 to 41, 74
to 78, 108 to 110,
139 to 141, 158 to
175, 208 to 241, Read & Write Yes Cell 0.1
270 to 274, 335 to
341, 358 to 371,
408 to 437, and 466
to 470.
In a Cell MO, if
CustomizedBand
WidthCfgInd is set
to CFG,
CustomizedULBan
dWidth and
CustomizedDLBan
dWidth cannot both
be set to 50, 100,
150, or 200.
If
EmergencyAreaIdC
fgInd is set to CFG,
EmergencyAreaId
must be set.
No (And no impact
If
EmergencyAreaIdC
mode)
fgInd is set to
NOT_CFG,
EmergencyAreaId
does not need to be
set.
EmergencyAreaId
is optional,
depending on the
setting of
EmergencyAreaIdC
fgInd.
If
EmergencyAreaIdC
No (And no impact
fgInd is set to CFG,
EmergencyAreaId
mode)
must be set.
If
EmergencyAreaIdC
fgInd is set to
NOT_CFG,
EmergencyAreaId
does not need to be
set.
If
UePowerMaxCfgInd
is set to CFG,
No (Modifications
UePowerMax must
on this parameter
be set.
If
reselection of the
UePowerMaxCfgInd
UE in idle mode.)
is set to NOT_CFG,
UePowerMax does
not need to be set.
When the
HighSpeedFlag in
Cell MO is
EXTRA_HIGH_SPE
ED, the range of
No (Modifications
the UePowerMax is
on this parameter
-27~36.
When the
reselection of the
HighSpeedFlag in
UE in idle mode.)
Cell MO is not
EXTRA_HIGH_SPE
ED, the range of
the UePowerMax is
-30~33.
ON, respectively,
FddTddInd must
be set to TDD.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
5M,
MultiRruCellFlag
must be set
BOOLEAN_FALSE.
If MultiRruCellFlag
in a Cell MO is set
to
BOOLEAN_TRUE
and
MultiRruCellMode
in a Cell MO is set
to
DIGITAL_COMBINA
TION, FddTddInd
in Cell MO must be
set to FDD.
If MultiRruCellFlag
in a Cell MO is set
to
BOOLEAN_TRUE
and
MultiRruCellMode
in a Cell MO is set
to
DIGITAL_COMBINA
TION,
DlCyclicPrefix and
UlCyclicPrefix in
Cell MO must be
set to
NORMAL_CP.
are set to
BOOLEAN_TRUE
and
CELL_COMBINATI
ON, respectively,
FddTddInd must
be set to TDD.
If MultiRruCellFlag
in a Cell MO is set
to
BOOLEAN_TRUE
and
MultiRruCellMode
in a Cell MO is set
to
DIGITAL_COMBINA
TION, FddTddInd
in Cell MO must be
set to FDD.
If MultiRruCellFlag
in a Cell MO is set
to
BOOLEAN_TRUE
and
MultiRruCellMode
in a Cell MO is set
to
DIGITAL_COMBINA
TION,
DlCyclicPrefix and
UlCyclicPrefix in
Cell MO must be
set to
NORMAL_CP.
If MultiRruCellFlag
in a Cell MO is set
to
BOOLEAN_TRUE
5M,
CPRICompression
must be set
NO_COMPRESSIO
N.
In the Cell MO, if
FddTddInd is TDD
Model and
DlBandWidth is
CELL_BW_N50 or
CELL_BW_N100,
CPRICompression
can be set to
NO_COMPRESSIO
N or
NORMAL_COMPR
ESSION, if
DlBandWidth is
other values,
CPRICompression
must be set
NO_COMPRESSIO
N.
In the Cell MO, if
FddTddInd is FDD
Model and
DlBandWidth is
CELL_BW_N50,
CELL_BW_N75 or
CELL_BW_N100,
CPRICompression
can be set to
NO_COMPRESSIO
N or
NORMAL_COMPR
ESSION, if
DlBandWidth is
other values,




No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

In the CellMro MO,
if
CioAdjLimitCfgInd
No (And no impact
is set to CFG,
CioAdjLowerLimit
mode)
must be smaller
than
CioAdjUpperLimit.
In the CellMro MO,
if
CioAdjLimitCfgInd
No (And no impact
is set to CFG,
CioAdjLowerLimit
mode)
must be smaller
than
CioAdjUpperLimit.
In the CellMro MO,

if
CioAdjLimitCfgInd
No (And no impact
is set to CFG,
CioAdjLowerLimit
mode)
must be smaller
than
CioAdjUpperLimit.

In the CellRacThd
MO,
GoldServiceArpTh No (And no impact
d must be smaller Read & Write on the UE in idle N/A N/A
than mode)
SilverServiceArpT
hd.
In the CellRacThd
MO,
GoldServiceArpTh No (And no impact
d must be smaller Read & Write on the UE in idle N/A N/A
than mode)
SilverServiceArpT
hd.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci1HoThd must
be smaller than or No (And no impact
In the CellRacThd mode)
MO, the sum of
Qci1CongThd and
CongRelOffset
must be smaller
than Qci1HoThd.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci2HoThd must
MO, the sum of
Qci2CongThd and
CongRelOffset
must be smaller
than Qci2HoThd.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci3HoThd must
MO, the sum of
Qci3CongThd and
CongRelOffset
must be smaller
than Qci3HoThd.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci4HoThd must
MO, the sum of
Qci4CongThd and
CongRelOffset
must be smaller
than Qci4HoThd.
In the CellRacThd
MO,
NewGoldServiceO
No (And no impact
ffset must be
smaller than or
mode)
equal to
NewSilverService
Offset.
In the CellRacThd
MO,
NewGoldServiceO
ffset must be
smaller than or
equal to
NewSilverService
No (And no impact
Offset.
In the CellRacThd
mode)
MO,
NewSilverService
Offset must be
smaller than or
equal to
NewCopperServic
eOffset.
In the CellRacThd
MO,
NewSilverService
Offset must be
smaller than or
equal to
NewCopperServic
eOffset.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci1HoThd must
be smaller than or
equal to 100.
In the CellRacThd
MO, the sum of
No (And no impact
NewCopperServic
eOffset and
mode)
Qci2HoThd must
be smaller than or
equal to 100.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci3HoThd must
be smaller than or
equal to 100.
In the CellRacThd
MO, the sum of
NewCopperServic
eOffset and
Qci4HoThd must
be smaller than or
equal to 100.
In the CellRacThd
MO, the sum of
No (And no impact
Qci1CongThd and
CongRelOffset
mode)
must be smaller
than Qci1HoThd.
In the CellRacThd
MO, the sum of
Qci2CongThd and
CongRelOffset
must be smaller
than Qci2HoThd.
No (And no impact
In the CellRacThd
MO, the sum of
mode)
Qci2CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO, the sum of
Qci3CongThd and
CongRelOffset
must be smaller
than Qci3HoThd.
No (And no impact
In the CellRacThd
MO, the sum of
mode)
Qci3CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO, the sum of
Qci4CongThd and
CongRelOffset
must be smaller
than Qci4HoThd.
No (And no impact
In the CellRacThd
MO, the sum of
mode)
Qci4CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO,
GoldGbrCongProp
No (And no impact
ortion must be
greater than or
mode)
equal to
SilverGbrCongPro
portion.
In the CellRacThd
MO,
GoldGbrCongProp
ortion must be
greater than or
equal to
SilverGbrCongPro
No (And no impact
portion.
In the CellRacThd
mode)
MO,
SilverGbrCongPro
portion must be
greater than or
equal to
CopperGbrCongPr
oportion.
In the CellRacThd
MO,
SilverGbrCongPro
portion must be
greater than or
equal to
CopperGbrCongPr
oportion.
In the CellRacThd
MO, the sum of
Qci2CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
No (And no impact
oportion.
In the CellRacThd
mode)
MO, the sum of
Qci3CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO, the sum of
Qci4CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO,
GbrRbUsedHighT No (And no impact
hd must be greater Read & Write on the UE in idle N/A N/A
than or equal to mode)
GbrRbUsedLowTh
d.
In the CellRacThd
MO,
GbrRbUsedHighT No (And no impact
hd must be greater Read & Write on the UE in idle N/A N/A
GbrRbUsedLowTh
d.
No (And no impact
mode)
than Qci1HoThd.
In the CellRacThd
MO, the sum of
Qci2CongThd and
CongRelOffset
must be smaller
than Qci2HoThd.
In the CellRacThd
MO, the sum of
Qci3CongThd and
CongRelOffset
must be smaller
than Qci3HoThd.
In the CellRacThd
MO, the sum of
Qci4CongThd and
CongRelOffset
must be smaller
No (And no impact
than Qci4HoThd.
In the CellRacThd
mode)
MO, the sum of
Qci2CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO, the sum of
Qci3CongThd and
CongRelOffset
must be smaller
than
CopperGbrCongPr
oportion.
In the CellRacThd
MO, the sum of
Qci4CongThd and
No (And no impact
mode)
In the CellRacThd
No (And no impact
MO, UlRbHighThd
must be greater
mode)
than UlRbLowThd.
In the CellRacThd
No (And no impact
MO, DlRbHighThd
must be greater
mode)
than DlRbLowThd.
In the CellRacThd
No (And no impact
MO, UlRbHighThd
must be greater
mode)
than UlRbLowThd.
In the CellRacThd
No (And no impact
MO, DlRbHighThd
must be greater
mode)
than DlRbLowThd.
No (And no impact
mode)
PresenceAntennaP No (And no impact

ort1 must be set as Read & Write on the UE in idle N/A N/A
required. mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
CellShutdown MO,
the sum of No (And no impact
DlPrbThd and Read & Write on the UE in idle N/A N/A
DlPrbOffset must mode)
be smaller than or
equal to 100.
In the
CellShutdown MO,
DlPrbThd and Read & Write on the UE in idle N/A N/A
DlPrbOffset must mode)
be smaller than or
equal to 100.
In the
CellShutdown MO,
UlPrbThd and Read & Write on the UE in idle N/A N/A
UlPrbOffset must mode)
be smaller than or
equal to 100.
In the
CellShutdown MO,
UlPrbThd and Read & Write on the UE in idle N/A N/A
UlPrbOffset must mode)
be smaller than or
equal to 100.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
UlBandWidth in
the Cell MO, B the
even number that
HoppingOffset in
the PUSCHCFG
MO is rounded up
to, and C the
difference between
A and B. If
UlHoppingType in
the CellUlschAlgo
MO is set to
HOPPING_TYPE1,
C must be greater
than UlBandWidth
in the Cell MO
modulo 2. If
UlHoppingType in
the CellUlschAlgo
MO is set to
HOPPING_TYPE2
or
HOPPING_TYPE2_
RANDOM, C
modulo Nsb in the
PUSCHCfg MO
must be greater
than 0.
2. If the switch for
uplink ICIC in the
frequency domain
is turned on,
UlHoppingType in
the CellUlschAlgo
MO does not take
effect. In this
situation, the
default value
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

If
PrachConfigIndexC
fgInd in the
RACHCfg MO is set
to NOT_CFG and
RachAdjSwitch is
No (And no impact
turned on, the
RACH resources in
mode)
the cell can be
adaptively adjusted
based on the
access type and the
number of access
attempts.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
In the
CellDlschAlgo MO,
No (And no impact
OtherServiceWeig
ht must be greater
mode)
than or equal to
BtServiceWeight.
In the
CellDlschAlgo MO,
No (And no impact
OtherServiceWeig
ht must be greater
mode)
than or equal to
BtServiceWeight.
No (And no impact
mode)
In the CellMLB MO,

the sum of
IntraFreqMlbThd No (And no impact
and LoadOffset Read & Write on the UE in idle N/A N/A
must be smaller mode)
than or equal to
100.
In the CellMLB MO,
the sum of
InterFreqMlbThd No (And no impact
than or equal to
100.
In the CellMLB MO,

the sum of
InterRatMlbThd No (And no impact
than or equal to
100.
No (And no impact
mode)
In the CellMLB MO,

the sum of
InterFreqMlbThd
and LoadOffset
must be smaller
than or equal to
100.
In the CellMLB MO,
the sum of
InterRatMlbThd No (And no impact
than or equal to
100.
In the CellMLB MO,
the sum of
IntraFreqMlbThd
and LoadOffset
must be smaller
than or equal to
100.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)

In the
CellNoAccessAlm
Para MO, if
NoAccessStartDet
ectTime is different
from
NoAccessStopDet
ectTime, No (And no impact
NoAccessDetectTi Read & Write on the UE in idle N/A N/A
mer must be mode)
smaller than the
time difference
between
NoAccessStartDet
ectTime and
NoAccessStopDet
ectTime.
In the
CellNoAccessAlm
Para MO, if
NoAccessStartDet
from
NoAccessStopDet
mer must be mode)
smaller than the
time difference
between
NoAccessStartDet
ectTime and
NoAccessStopDet
ectTime.
In the
CellNoAccessAlm
Para MO, if
NoAccessStartDet
from
NoAccessStopDet
mer must be mode)
smaller than the
time difference
between
NoAccessStartDet
ectTime and
NoAccessStopDet
ectTime.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
This parameter
must be properly
set so that two
conditions are met:
(1) The PRACH
RBs are strictly
confined in the cell
bandwidth; (2) The
PRACH RBs and
PUCCH RBs do not
overlap. This
parameter is valid
only if
PucchAlgoSwitch in
the CellAlgoSwitch
MO is turned off.
If RachAdjSwitch in
the CellAlgoSwitch
MO is turned on
and this parameter
is set to CFG, this
parameter takes
precedence over
RachAdjSwitch.
The setting of this
parameter takes
effect only if
PrachConfigIndexC
fgInd is set to CFG. Read & Write Yes Cell 0.1
Otherwise, the
parameter setting
does not take
effect.




Let A be the value
of UlBandWidth in
the Cell MO, B the
even number that
HoppingOffset in
the PUSCHCFG
MO is rounded up
to, and C the
difference between
A and B. If
UlHoppingType in
the CellUlschAlgo
MO is set to
HOPPING_TYPE1,
C must be greater Read & Write Yes Cell 0.1
than UlBandWidth
in the Cell MO
modulo 2. If
UlHoppingType in
the CellUlschAlgo
MO is set to
HOPPING_TYPE2
or
HOPPING_TYPE2_
RANDOM, C
modulo Nsb in the
PUSCHCfg MO
must be greater
than 0.

Let A be the value
of UlBandWidth in
the Cell MO, B the
even number that
HoppingOffset in
the PUSCHCFG
MO is rounded up
to, and C the
difference between
A and B. If
UlHoppingType in
the CellUlschAlgo
MO is set to
HOPPING_TYPE1,
C must be greater Read & Write Yes Cell 0.1
than UlBandWidth
in the Cell MO
modulo 2. If
UlHoppingType in
the CellUlschAlgo
MO is set to
HOPPING_TYPE2
or
HOPPING_TYPE2_
RANDOM, C
modulo Nsb in the
PUSCHCfg MO
must be greater
than 0.
No (And no impact
mode)
No (And no impact
mode)
This parameter can

be set only if
PucchAlgoSwitch in
the CellAlgoSwitch
MO is turned off. Read & Write Yes Cell 0.1
Otherwise, the
parameter setting
does not take
effect.
This parameter can
be set only if
PucchAlgoSwitch in
the CellAlgoSwitch
MO is turned off. Read & Write Yes Cell 0.1
Otherwise, the
parameter setting
does not take
effect.
CellGlobalId in a
Cdma2000Externa
lCellPlmn MO can
only be set to a
hexadecimal
number.
ShareMcc in a
Cdma2000Externa
lCellPlmn MO Read Only N/A N/A N/A
consists of digits
only.
ShareMnc in a
Cdma2000Externa
lCellPlmn MO Read Only N/A N/A N/A
consists of digits
only.

CellGlobalId in a
Cdma2000HrpdNc
ell MO consists of Read Only N/A N/A N/A
16 digits or 32 hex
numbers.
No (And no impact
mode)
No (And no impact
mode)
In each
Cdma2000HrpdNc
ell MO of a local
No (And no impact
cell,
BlindHoPriority
mode)
must have a unique
value if it is not set
to 0.
In the
Cdma2000HrpdNc
ell MO, the value of
LocalCellName is
a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters:double No (And no impact
quotation marks ("), Read & Write on the UE in idle N/A N/A
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
In the
Cdma2000HrpdNc
NeighbourCellNa
me is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
A maximum of 16
Cdma2000Nfreq
MOs with the same
combination of Read Only N/A N/A N/A
LocalCellId and
BandClass can be
configured.
A maximum of 16
Cdma2000Nfreq
MOs with the same
combination of Read Only N/A N/A N/A
LocalCellId and
BandClass can be
configured.

No (And no impact
mode)
No (And no impact
mode)
If
SearchWindowSize
No (And no impact
CfgInd is set to
CFG,
mode)
SearchWindowSize
must be set.
Mcc in an
EutranExternalCell
Plmn MO consists
of digits only.
In an
EutranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
different from that of
ShareMnc and
ShareMcc.
In an
EutranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
Mnc in an
EutranExternalCell
Plmn MO consists
of digits only.

In an
EutranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
ShareMcc in an
EutranExternalCell
Plmn MO consists
of digits only.
In an
EutranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
ShareMnc in an
EutranExternalCell
Plmn MO consists
of digits only.
In a
GeranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
Mcc in a
GeranExternalCell
Plmn MO consists
of digits only.
In a
GeranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
Mnc in a
GeranExternalCell
Plmn MO consists
of digits only.
In a
GeranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
ShareMcc in a
GeranExternalCell
Plmn MO consists
of digits only.
In a
GeranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
ShareMnc in a
GeranExternalCell
Plmn MO consists
of digits only.
Mcc in a
UtranExternalCell
Plmn MO consists
of digits only.
In a
UtranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
In a
UtranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
Mnc in a
UtranExternalCell
Plmn MO consists
of digits only.
In a
UtranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
ShareMcc in a
UtranExternalCell
Plmn MO consists
of digits only.
In a
UtranExternalCell
Plmn MO, the
combination of Mnc
and Mcc must be
ShareMnc and
ShareMcc.
ShareMnc in a
UtranExternalCell
Plmn MO consists
of digits only.
Cdma2000Externa
lCell MO, if
Cdma2000Type is
set to
CDMA2000_HRPD,
CellGlobalId must
be set to a value of
16 digits or 32
hexadecimal digits.
In a
Cdma2000Externa
lCell MO, if
Cdma2000Type is
set to
CDMA2000_HRPD,
CellGlobalId is set
to a 32
hexadecimal-digit
value, and the 16 Read Only N/A N/A N/A
hexadecimal digits
from right to left are
all set to 0, the
remaining 16
hexadecimal digits
same digits as the
16 decimal-digit
value specified by
CellGlobalId in any
existing
Cdma2000Externa
lCell MO. In a
Cdma2000Externa
lCell MO, if
Cdma2000Type is
set to
CDMA2000_1XRTT
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
Mcc in a
No (And no impact
Cdma2000Externa
lCell MO consists
mode)
of digits only.
Mnc in a
No (And no impact
Cdma2000Externa
lCell MO consists
mode)
of digits only.
In the
Cdma2000Externa
lCell MO, the value
of CellName is a
string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).

In a
Cdma20001XRTTN
cell MO,
CellGlobalId must
be set to a value of
6 digits or 12
hexadecimal digits. Read Only N/A N/A N/A
Note that when
CellGlobalId is set
to a value of 12
hexadecimal digits,
the 48th bit cannot
be 1.
No (And no impact
mode)
No (And no impact
mode)
In each
Cdma20001XRTTN
cell MO of a local
No (And no impact
cell,
BlindHoPriority
mode)
must have a unique
to 0.
In the
Cdma20001XRTTN
cell MO, the value
of LocalCellName
is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
In the
Cdma20001XRTTN
cell MO, the value
of
NeighbourCellNa
me is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
No (And no impact
characters:double
mode)
commas (,),
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).

The greater the
parameter, the
greater the
possibility for the
UE to camp in this No (And no impact
cell. The smaller the Read & Write on the UE in idle N/A N/A
parameter is, the mode)
smaller the
possibility for the
UE to camp in this
cell.
No (And no impact
mode)
No (And no impact
mode)
Mcc in a
GeranExternalCell
MO consists of
digits only.
Mnc in a
GeranExternalCell
MO consists of
digits only.
When RacCfgInd is
set to CFG, Rac
must be set. No (And no impact
When RacCfgInd is Read & Write on the UE in idle N/A N/A
set to NOT_CFG, mode)
Rac does not need
to be set.
When RacCfgInd is
set to CFG, Rac
must be set. No (And no impact
When RacCfgInd is Read & Write on the UE in idle N/A N/A
set to NOT_CFG, mode)
Rac does not need
to be set.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
GeranExternalCell
MO, the value of
CellName is a
string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
No (And no impact
mode)

Mcc in a
GeranNcell MO
consists of digits
only.
Mnc in a
GeranNcell MO
consists of digits
only.
No (And no impact
mode)
No (And no impact
mode)
In each GeranNcell
MO of a local cell,
No (And no impact
BlindHoPriority
must have a unique
mode)
to 0.
In the GeranNcell
MO, the value of
LocalCellName is
a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters:double
No (And no impact
commas (,),
mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
In the GeranNcell
MO, the value of
NeighbourCellNa
me is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters:double
No (And no impact
commas (,),
mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If
CellReselPriorityCfg No (And no impact
Ind is set to CFG, Read & Write on the UE in idle N/A N/A
CellReselPriority mode)
must be set.
If
PmaxGeranCfgInd
is set to CFG,
PmaxGeran must
No (And no impact
be set.
If
mode)
PmaxGeranCfgInd
is set to NOT_CFG,
PmaxGeran does
not need to be set.
If
PmaxGeranCfgInd
is set to CFG,
PmaxGeran must
No (And no impact
be set.
If
mode)
PmaxGeranCfgInd
is set to NOT_CFG,
PmaxGeran does
not need to be set.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

The sum of the

value of
PhyCellIdRange(n
1 is 1,N4 is 4, N8 is
8,and so on) and
the value of Read Only N/A N/A N/A
PhyCellId must be
smaller than 504 in
the
IntraFreqBlkCell
MO.
No (And no impact
mode)
The sum of the
value of
PhyCellIdRange(n
1 is 1,N4 is 4, N8 is
8,and so on) and No (And no impact
the value of Read & Write on the UE in idle N/A N/A
PhyCellId must be mode)
smaller than 504 in
the
IntraFreqBlkCell
MO.
Mcc in an
EutranIntraFreqNC
ell MO consists of
digits only.
Mnc in an
EutranIntraFreqNC
ell MO consists of
digits only.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
EutranIntraFreqNC
LocalCellName is
a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
In the
EutranIntraFreqNC
NeighbourCellNa
me is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters: double No (And no impact
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).

DlEarfcn in an
EutranInterNFreq
MO must be a valid
frequency.
No (And no impact
mode)
UlEarfcn in an
No (And no impact
EutranInterNFreq
MO must be a valid
mode)
frequency.
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
CellReselPriorityCfg on this parameter
Ind is set to CFG, Read & Write will affect cell N/A N/A
CellReselPriority reselection of the
No (And no impact
mode)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
SpeedDependSPCf on this parameter
gInd is set to CFG, Read & Write would affect cell N/A N/A
TReselEutranSfMe reselection of the
dium must be set. UE in idle mode.)
SpeedDependSPCf on this parameter
gInd is set to CFG, Read & Write would affect cell N/A N/A
TReselEutranSfHig reselection of the
h must be set. UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
A larger value of
this parameter
leads to a lower
probability of a cell
meeting criteria S
and becoming a
suitable cell for cell
No (Modifications
selection. A smaller
on this parameter
value of this
parameter leads to
reselection of the
UE in idle mode.)
Set this parameter
properly so that the
selected cell can
provide signals that
meet the quality
requirement of
basic services.
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
If PmaxCfgInd is on this parameter
set to CFG, Pmax Read & Write would affect cell N/A N/A
UE in idle mode.)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
No (Modifications
on this parameter
reselection of the
UE in idle mode.)
If QqualMinCfgInd
is set to CFG, this
No (Modifications
parameter must be
on this parameter
set.
If QqualMinCfgInd
reselection of the
is set to NOT_CFG,
UE in idle mode.)
this parameter does
not need to be set.
No (Modifications
on this parameter
reselection of the
UE in idle mode.)

DlEarfcn in an
InterFreqBlkCell
MO must be a valid
frequency.
The sum of the

value of
PhyCellIdRange(n
1 is 1,N4 is 4, N8 is
8,and so on) and
the value of Read Only N/A N/A N/A
PhyCellId must be
smaller than 504 in
the
InterFreqBlkCell
MO.
No (And no impact
mode)
The sum of the
value of
PhyCellIdRange(n
1 is 1,N4 is 4, N8 is
8,and so on) and No (And no impact
the value of Read & Write on the UE in idle N/A N/A
PhyCellId must be mode)
smaller than 504 in
the
InterFreqBlkCell
MO.
Mcc in an
EutranInterFreqNC
ell MO consists of
digits only.
Mnc in an
EutranInterFreqNC
ell MO consists of
digits only.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In each
EutranInterFreqNC
ell MO of a local
No (And no impact
cell,
BlindHoPriority
mode)
must have a unique
to 0.
In the
EutranInterFreqNC
LocalCellName is
a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
In the
EutranInterFreqNC
NeighbourCellNa
me is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
Mcc in an
EutranExternalCell
MO consists of
digits only.
Mnc in an
EutranExternalCell
MO consists of
digits only.

DlEarfcn in an
No (And no impact
EutranExternalCell
MO must be a valid
mode)
frequency.
No (And no impact
mode)
UlEarfcn in an
No (And no impact
EutranExternalCell
MO must be a valid
mode)
frequency.
No (And no impact
mode)
No (And no impact
mode)
In the
EutranExternalCell
MO, the value of
CellName is a
string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).


No (And no impact
mode)
This parameter is
CellReselPriorityCfg mode)
Ind.

Mcc in a
UtranNCell MO
consists of digits
only.
Mnc in a
UtranNCell MO
consists of digits
only.

No (And no impact
mode)
No (And no impact
mode)
In each UtranNCell
MO of a local cell,
No (And no impact
BlindHoPriority
must have a unique
mode)
to 0.

In the UtranNCell
MO, the value of
LocalCellName is
a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters:double
No (And no impact
commas (,),
mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
In the UtranNCell
MO, the value of
NeighbourCellNa
me is a string of a
maximum of 99
characters. The
null characters or
contain any of the
following
characters:double
No (And no impact
commas (,),
mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).



No (And no impact
mode)
This parameter is
CellReselPriorityCfg mode)
Ind.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
1. If
UtranUlArfcnCfgInd
is set to CFG,
UtranUlArfcn must
No (And no impact
be set.
2. The DL UARFCN
mode)
and UL UARFCN
must be in the
same frequency
band.
No (And no impact
mode)
If
CellReselPriorityCfg No (And no impact
Ind is set to CFG, Read & Write on the UE in idle N/A N/A
CellReselPriority mode)
must be set.
No (And no impact
mode)
No (And no impact
mode)
Qqualmin must be
set if No (And no impact
UtranFddTddType Read & Write on the UE in idle N/A N/A
is set to mode)
UTRAN_FDD.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
ThreshXHighQ
must be set if No (And no impact
is set to mode)
UTRAN_FDD.
ThreshXLowQ must
be set if No (And no impact
is set to mode)
UTRAN_FDD.
No (And no impact
mode)
No (And no impact
mode)
Mcc in a
UtranExternalCell
MO consists of
digits only.
Mnc in a
UtranExternalCell
MO consists of
digits only.
In a
UtranExternalCell
MO, The most
significant 12 bits of Read Only N/A N/A N/A
UtranCellId must
be the same to
RncId.
In a
UtranExternalCell
MO,
PScrambCode No (And no impact
cannot exceed 127 Read & Write on the UE in idle N/A N/A
if mode)
UtranFddTddType
is set to
UTRAN_TDD.
In all
UtranExternalCell
MOs of a local cell,
the combination of
No (And no impact
UtranDlArfcn and
PScrambCode
mode)
must be unique in
each
UtranExternalCell
MO.
When
UtranUlArfcnCfgInd
is set to CFG,
UtranUlArfcn must
be set. No (And no impact
If Read & Write on the UE in idle N/A N/A
UtranUlArfcnCfgInd mode)
is set to NOT_CFG,
UtranUlArfcn does
not need to be
configured.
No (And no impact
mode)
In a
UtranExternalCell
MO, The most No (And no impact
significant 12 bits of Read & Write on the UE in idle N/A N/A
UtranCellId must mode)
be the same to
RncId.
No (And no impact
mode)
If RacCfgInd is set
No (And no impact
to CFG, this
parameter must be
mode)
set.
In all
UtranExternalCell
MOs of a local cell,
the combination of
UtranDlArfcn and
PScrambCode
must be unique in
each
UtranExternalCell No (And no impact
MO. Read & Write on the UE in idle N/A N/A
In a mode)
UtranExternalCell
MO,
PScrambCode
cannot exceed 127
if
UtranFddTddType
is set to
UTRAN_TDD.
No (And no impact
mode)
In the
UtranExternalCell
MO, the value of
CellName is a
string of a
maximum of 99
characters. The
null characters or
contain any of the
following
commas (,), mode)
semicolons (;),
equal signs (=),
single quotation
marks ('), three
consecutive plus
signs (+++), two or
more consecutive
blanks, and two or
more consecutive
percentage signs
(%).
No (And no impact
mode)
In the ANR MO,
AddCellThd must No (And no impact
be greater than or Read & Write on the UE in idle N/A N/A
equal to mode)
DelCellThd.
In the ANR MO,
AddCellThd must No (And no impact
be greater than or Read & Write on the UE in idle N/A N/A
equal to mode)
DelCellThd.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
Cells configured
with punctured RBs
and non-standard
bandwidths support No (And no impact
only static ICIC. If Read & Write on the UE in idle N/A N/A
adaptive DL ICIC is mode)
enabled, static and
dynamic DL ICIC do
not take effect.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
If adaptive UL ICIC
is enabled, static No (And no impact
and dynamic UL Read & Write on the UE in idle N/A N/A
ICIC do not take mode)
effect.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the LicRatio MO,
No (And no impact
RTHD must be
smaller than or
mode)
equal to OTHD.
No (And no impact
mode)
In the LicRatio MO,

No (And no impact
RTHD must be
smaller than or
mode)
equal to OTHD.
No (And no impact
mode)
No (And no impact
mode)
In the LicRatio MO,

the sum of
Operator1TrfRatio,
Operator2TrfRatio,
Operator3TrfRatio,
Operator4TrfRatio,
Operator5TrfRatio
and
No (And no impact
Operator6TrfRatio
must be smaller
mode)
than or equal to
100.
In the LicRatio MO,
Operator1TrfShari
ngRatio must be
smaller than or
equal to
Operator1TrfRatio.
In the LicRatio MO,
the sum of
Operator1TrfRatio,
Operator2TrfRatio,
Operator3TrfRatio,
Operator4TrfRatio,
Operator5TrfRatio
and
Operator6TrfRatio No (And no impact
100.
In the LicRatio MO,
Operator2TrfShari
ngRatio must be
smaller than or
equal to
Operator2TrfRatio.
In the LicRatio MO,
the sum of
Operator1TrfRatio,
Operator2TrfRatio,
Operator3TrfRatio,
Operator4TrfRatio,
Operator5TrfRatio
and
100.
In the LicRatio MO,
Operator3TrfShari
ngRatio must be
smaller than or
equal to
Operator3TrfRatio.
In the LicRatio MO,
the sum of
Operator1TrfRatio,
Operator2TrfRatio,
Operator3TrfRatio,
Operator4TrfRatio,
Operator5TrfRatio
and
100.
In the LicRatio MO,
Operator4TrfShari
ngRatio must be
smaller than or
equal to
Operator4TrfRatio.
In the LicRatio MO,
the sum of
Operator1TrfRatio,
Operator2TrfRatio,
Operator3TrfRatio,
Operator4TrfRatio,
Operator5TrfRatio
and
100.
In the LicRatio MO,
Operator5TrfShari
ngRatio must be
smaller than or
equal to
Operator5TrfRatio.
In the LicRatio MO,
the sum of
Operator1TrfRatio,
Operator2TrfRatio,
Operator3TrfRatio,
Operator4TrfRatio,
Operator5TrfRatio
and
100.
In the LicRatio MO,
Operator6TrfShari
ngRatio must be
smaller than or
equal to
Operator6TrfRatio.
In the LicRatio MO,

Operator1TrfShari
No (And no impact
ngRatio must be
smaller than or
mode)
equal to
Operator1TrfRatio.
In the LicRatio MO,
Operator2TrfShari No (And no impact

ngRatio must be Read & Write on the UE in idle N/A N/A
smaller than or mode)
equal to
Operator2TrfRatio.
In the LicRatio MO,

equal to
Operator3TrfRatio.
In the LicRatio MO,

equal to
Operator4TrfRatio.
In the LicRatio MO,

equal to
Operator5TrfRatio.
In the LicRatio MO,

equal to
Operator6TrfRatio.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
OBJTORSCGROU
PID in an
NODETORSCGRP
MO must be
different from that in
any other
NODETORSCGRP
MO.
If ISALLMATCH in
an
NodeToRscGroup
MO is YES,
S1X2FLAG,
CABINETNO,
SUBRACKNO,
SLOTNO, SBT, PT
in this MO must be
any other
configured
NodeToRscGroup
MO with
ISALLMATCH set
to YES. Less than one
Read & Write Yes NE
If ISALLMATCH in minute
an
NodeToRscGroup
MO is NO,
S1X2FLAG,ENDP
OINTID,CABINETN
O,SUBRACKNO,S
LOTNO,SBT,PT in
this MO must be
any other
configured
NodeToRscGroup
MO with
ISALLMATCH set
to NO.
Less than one

None Read & Write Yes NE
minute
In a
NODETORSCGRP
MO, ENDPOINTID
is valid only when
ISALLMATCH is
set to NO.
In a
NODETORSCGRP
MO, if S1X2FLAG
is set to SGW,
ENDPOINTID must Less than one
Read & Write Yes NE
be set to a value in minute
the range of 0 to
127.
In a
NODETORSCGRP
MO, if S1X2FLAG
is set to X2eNodeB,
ENDPOINTID must
be set to a value in
the range of 16 to
79.
Less than one

minute
Less than one

minute
Less than one

minute
Less than one

minute
Before adding an
NodeToRscGroup
MO, ensure that the Less than one
Read & Write Yes NE
associated minute
RSCGRP MO has
been configured.
In an
NodeToRscGroup
MO, this parameter
can be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SLOTNO is set
to a value within the
Less than one
range of 0 to 5. Read & Write Yes NE
minute
In an
NodeToRscGroup
MO, this parameter
can be set to
BASE_BOARD,
BACK_BOARD or
ETH_COVERBOAR
D if SLOTNO is set
to 6 or 7.
Less than one

minute
In an
NodeToRscGroup
MO, this parameter
can be set
toPPP,MPGRP,ETH
or ETHTRK if SBT
is set to
BASE_BOARD.
In an
NodeToRscGroup
MO, this parameter
can be set to
TUNNEL if SBT is
set to
BACK_BOARD.
Less than one
In an Read & Write Yes NE
minute
NodeToRscGroup
MO, this parameter
can be set to PPP
or MPGRP if SBT is
set to
E1_COVERBOARD
.
In an
NodeToRscGroup
MO, this parameter
can be set to ETH
or ETHTRK if SBT
is set to
ETH_COVERBOAR
D.
SONSECPARANA
ME in an
SonSecPara MO No (And no impact
must be different Read Only on the UE in idle N/A N/A
from that in any mode)
other SonSecPara
MO.
PROPID in an
SONSECPARA MO
must be the same
as PROPID in a
No (And no impact
configured
IKEPROPOSAL
mode)
MO.
PROPID in an
SONSECPARA MO
cannot be empty.
PROPNAME in an
SONSECPARA MO
cannot be empty.
PROPNAME in an
No (And no impact
SONSECPARA MO
must be the same
mode)
as PROPNAME in
a configured
IPSECPROPOSAL
MO.
Only one S1
SONSECPARA
object can be
configured for each
No (And no impact
operator.
Only one X2
mode)
SONSECPARA
object can be
configured for each
operator.
If AUTHALG in an
IKEPROPOSAL
MO is set to
AES_XCBC_96, No (And no impact
IKEVERSION in the Read & Write on the UE in idle N/A N/A
associated mode)
SONSECPARA MO
cannot be set to
IKE_V1.
In an SonSecPara
MO, this parameter No (And no impact
IKEVERSION is set mode)
to IKE_V1.
If AUTHMETH in
the IKEPROPOSAL
MO associated with
an SONSECPARA No (And no impact
MO is set to Read & Write on the UE in idle N/A N/A
PRE_SHARED_KE mode)
Y, PKEY in the
SONSECPARA MO
cannot be empty.
No (And no impact
mode)
In an SonSecPara
DPD is set to mode)
PERIODIC.
No (And no impact
mode)
In an SonSecPara
DPD is set to mode)
PERIODIC.
No (And no impact
mode)
No (And no impact
mode)
In an SonSecPara
LTCFG is set to mode)
LOCAL.
In an SonSecPara
LTCFG is set to mode)
LOCAL.
CNOPERATORID
in an
SONSECPARA MO No (And no impact
must be the same Read & Write on the UE in idle N/A N/A
as CnOperatorId in mode)
a configured
CnOperator MO.
MMEID in an MME6
MO must be
different from that in Read Only N/A N/A N/A
any other MME6
MO.
SIGIP1 in an MME6
MO must be
different from IPV6
in any configured
DEVIP6 MO.
SIGIP1 in an MME6
MO must be set to
a global unicast
address.
SIGIP1 in an MME6
MO must be Read & Write Yes NE Less than 1 minute
different from
SIGIP1 and SIGIP2
in any configured
X2ENODEB6 MO.
SIGIP1 in an MME6
MO must be
different from
SIGIP1 and SIGIP2
in any configured
MME6 MO.
None Read & Write Yes NE Less than 1 minute
If SIGIP1SECFLAG
in an MME6 MO is
set to ENABLE,
IKEPEERNM1 in
this MO must be Read & Write Yes NE Less than 1 minute
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If SIGIP1SECFLAG
in an MME6 MO is
set to ENABLE,
IPSECPROPNM1
in this MO must be
Read & Write Yes NE Less than 1 minute
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
SIGIP2 in an MME6
MO must be
different from IPV6
in any configured
DEVIP6 MO.
In an MME6 MO, if
SIGIP2 is not
0:0:0:0:0:0:0:0, it
must be different
from SIGIP1.
If SIGIP2 in an
MME6 MO is not
0:0:0:0:0:0:0:0, it
must be different
from SIGIP1 and
SIGIP2 in any other
configured MME6
MO.
If SIGIP2 in an
MME6 MO is not
0:0:0:0:0:0:0:0, it
must be set to a
global unicast
address.
If SIGIP2 in an
MME6 MO is not
0:0:0:0:0:0:0:0, it
must be different
from SIGIP1 and
SIGIP2 in any other
configured
X2ENODEB6 MO.
If SIGIP2SECFLAG
in an MME6 MO is
set to ENABLE,
IKEPEERNM2 in
this MO must be Read & Write Yes NE Less than 1 minute
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If SIGIP2SECFLAG
in an MME6 MO is
set to ENABLE,
IPSECPROPNM2
in this MO must be
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.

No (And no impact
mode)
CNOPERATORID
in an MME6 MO
must be the same
as CnOperatorId in
a configured
CnOperator MO.
Less than one

minute
MMEID in an MME
MO must be
any other MME MO.
FIRSTSIGIP in an
MME MO must be
different from IP in
any configured
DEVIP MO.
FIRSTSIGIP in an
MME MO must be
different from
FIRSTSIGIP and
SECSIGIP in any
other configured
MME MO.
FIRSTSIGIP in an
Less than one
MME MO must be Read & Write Yes NE
minute
different from
FIRSTSIGIP and
SECSIGIP in any
configured
X2ENODEB MO.
FIRSTSIGIP in an
MME MO must be a
valid IP address of
Class A, B, or C. In
addition, this IP
address cannot be
set to 127.x.x.x or
0.x.x.x.
Less than one

minute
If
FIRSTIPSECFLAG
in an MME MO is
set to ENABLE,
FIRSTIKEPEERNM Less than one
Read & Write Yes NE
in this MO must be minute
the same as
PEERNAME in a
configured
IKEPEER MO.
If
FIRSTIPSECFLAG
in an MME MO is
set to ENABLE,
FIRSTIPSECPROP
Less than one
NM in this MO must Read & Write Yes NE
minute
be the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
SECSIGIP in an
MME MO must be
any configured
DEVIP MO.
If SECSIGIP in an
MME MO is not
0.0.0.0, it must be
set to a valid IP
address of Class A,
B, or C. In addition,
this IP address
cannot be set to
127.x.x.x or 0.x.x.x.
In an MME MO, if
SECSIGIP is not
0.0.0.0, it must be
Less than one
different from Read & Write Yes NE
minute
FIRSTSIGIP.
If SECSIGIP in an
MME MO is not
0.0.0.0, it must be
different from
FIRSTSIGIP or
SECSIGIP in any
other configured
MME MO.
If SECSIGIP in an
MME MO is not
0.0.0.0, it must be
different from
FIRSTSIGIP or
SECSIGIP in any
configured
X2ENODEB MO.
Less than one

minute
If SECIPSECFLAG
in an MME MO is
set to ENABLE,
SECIKEPEERNM
Less than one
in this MO must be Read & Write Yes NE
minute
the same as
PEERNAME in a
configured
IKEPEER MO.
If SECIPSECFLAG
in an MME MO is
set to ENABLE,
SECIPSECPROPN
M in this MO must Less than one
Read & Write Yes NE
be the same as minute
PROPNAME in a
configured
IPSECPROPOSAL
MO.
Less than one

minute
Less than one

minute
CNOPERATORID
in an MME MO
must be the same Less than one
Read & Write Yes NE
as CnOperatorId in minute
a configured
CnOperator MO.
Less than one
minute
Less than one

minute
Less than one

minute
Less than one

minute
S1SERVIPID in an
S1ServIP MO must
be different from Read Only N/A N/A N/A
that in any other
S1ServIP MO.
configured, the
eNodeB must be
configured with an
IP route that can
reach the SERVIP1
in the SGW MO or
with a DEVIP MO
that is on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPINT.
If PT in the DEVIP
MO associated with
S1SERVIP in an
S1SERVIP MO is
set to LOOPINT,
and SERVIP2 in an Less than one
Read & Write Yes NE
SGW MO is not minute
0.0.0.0, the eNodeB
must be configured
with an IP route that
can reach this
SERVIP2 or with a
DEVIP MO that is
on the same
network segment
as this SERVIP2
and has PT set to a
value other than
LOOPINT.
If PT in the DEVIP
MO associated with
S1SERVIP in an
S1SERVIP MO is
set to LOOPINT,
and SERVIP3 in an
Less than one

minute
configured DEVIP
MO.
If IKEIP in an
S1SERVIP MO is
valid, it must be a
valid IP address of
addition, this IP
address cannot be
set to 127.x.x.x or
0.x.x.x.
If IKEIP in an
S1SERVIP MO is
valid, it must be the
same as IP in a
configured DEVIP
MO with PT set to
ETH or ETHTRK.
If IKEIP in an Less than one
Read & Write Yes NE
S1SERVIP MO is minute
valid and PT in the
DEVIP MO
associated with
S1SERVIP is not
set to LOOPINT, PN
in the DEVIP MO
associated with this
IKEIP must be the
same as that in the
DEVIP MO
S1SERVIP.
If IKEIP in an
S1SERVIP MO is
valid, CN, SRN, and
SN in the
S1SERVIP MO
must be the same
Less than one
minute
CNOPERATORID
in an S1SERVIP
MO must be the
same as Read & Write Yes eNodeB Less than 1 minute
CnOperatorId in a
configured
CnOperator MO.
S1ServIP6ID in an
S1ServIP6 MO
must be different
from that in any
other S1ServIP6
MO.

configured with an
IPv6 route that can
reach SERVIP1 in
the SGW6 MO or
with a DEVIP6 MO
that is on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPIF.
If PT in the IPITF6
MO associated with
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
SERVIP2 in an
SGW6 MO is not
0:0:0:0:0:0:0:0, the Read & Write Yes BS Less than 1 minute
eNodeB must be
configured with an
IPv6 route that can
reach this SERVIP2
or with a DEVIP6
MO that is on the
same network
segment as this
SERVIP2 and has
PT set to a value
other than LOOPIF.
If PT in the IPITF6
MO associated with
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
SERVIP3 in an
SGW6 MO is not
same as IPV6 in a
configured DEVIP6
MO.
In an S1SERVIP6
MO, if SERVIKEIP
is not "::", it must be
a global unicast
address.
If SERVIKEIP in an
S1SERVIP6 MO is
valid, CN, SRN, and
SN in the
S1SERVIP6 MO
must be the same
as those in the
IPITF6 MO
SERVIKEIP.
If SERVIKEIP in an
S1SERVIP6 MO is
same as IPV6 in a
configured DEVIP6
MO whose
associated IPITF6
MO has PT set to
ETH or TRUNK.
If SERVIKEIP in an
S1SERVIP6 MO is
valid and PT in the
IPITF6 MO
associated with
SERVIP is not set
to LOOPINT, PN in
the IPITF6 MO
SERVIKEIP must
be the same as that
CNOPERATORID
in an S1SERVIP6
MO must be the
same as Read & Write Yes BS Less than 1 minute
CnOperatorId in a
configured
CnOperator MO.
Less than one

minute
Less than one

minute
Less than one

minute
S1SIGIPID in an
S1SigIP MO must
that in any other
S1SigIP MO.
LOCIP in an
S1SIGIP MO must
be the same as IP
in a configured
DEVIP MO.
If LOCIP in an
S1SIGIP MO is
valid, it must be a
valid IP address of
addition, this IP Less than one
Read & Write Yes NE
address cannot be minute
set to 127.x.x.x or
0.x.x.x.
CN, SRN, and SN
in the DEVIP MO
associated with
LOCIP in an
S1SigIP MO must
be the same as
those in the same
S1SigIP MO.
Less than one

minute
configured DEVIP
MO.
If LOCIKEIP in an
S1SIGIP MO is
valid, it must be a
valid IP address of
addition, this IP
address cannot be
set to 127.x.x.x or
0.x.x.x.
If LOCIKEIP in an
S1SIGIP MO is
valid and PT in the
DEVIP MO
associated with
LOCIP is not set to
LOOPINT, PN in the
Less than one
DEVIP MO Read & Write Yes NE
minute
LOCIKEIP must be
the same as that in
the DEVIP
LOCIP.
If LOCIKEIP in an
S1SIGIP MO is
same as IP in a
configured DEVIP
MO with PT set to
ETH or ETHTRK.
If LOCIKEIP in an
S1SIGIP MO is
valid, CN, SRN, and
SN in the S1SIGIP
MO must be the
If SECLOCIP in an
S1SIGIP MO is not
0.0.0.0, it must be
the same as IP in a
configured DEVIP
MO.
If SECLOCIP in an
S1SIGIP MO is not
0.0.0.0, it must be
different from
LOCIP.
If SECLOCIP in an
S1SIGIP MO is
valid, it must be a Less than one
Read & Write Yes NE
valid IP address of minute
addition, this IP
address cannot be
set to 127.x.x.x or
0.x.x.x.
CN, SRN, and SN
in an S1SIGIP MO
must be the same
as those in the
DEVIP MO
associated with
SECLOCIP in the
S1SIGIP MO.
Less than one

minute
configured DEVIP
MO.
If SECLOCIKEIP in
an S1SIGIP MO is
valid, it must be a
valid IP address of
addition, this IP
address cannot be
set to 127.x.x.x or
0.x.x.x.
If SECLOCIKEIP in
an S1SIGIP MO is
valid and PT in the
DEVIP MO
associated with
SECLOCIP is not
set to LOOPINT, PN
in the DEVIP MO Less than one
Read & Write Yes NE
associated with this minute
SECLOCIKEIP
must be the same
as that in the
DEVIP associated
with this
SECLOCIP.
If SECLOCIKEIP in
an S1SIGIP MO is
same as IP in a
configured DEVIP
MO with PT set to
ETH or ETHTRK.
If SECLOCIKEIP in
an S1SIGIP MO is
valid, CN, SRN, and
SN in the S1SIGIP
MO must be the
Less than one

minute
Less than one
minute
In an S1SIGIP MO,
Less than one
RTOMIN must be Read & Write Yes NE
minute
less than RTOMAX.
In an S1SIGIP MO,
RTOINIT must be
greater than or Less than one
Read & Write Yes NE
equal to RTOMIN minute
and less than
RTOMAX.
Less than one

minute
Less than one
minute
Less than one

minute
MAXASSOCRETR
must be greater Less than one
Read & Write Yes NE
than minute
MAXPATHRETR.
MaxPathRetr must
Less than one
be less than Read & Write Yes NE
minute
MaxAssocRetr.
Less than one

minute
Less than one

minute
Less than one

minute
Less than one
minute
In an S1SigIP MO,
this parameter is
valid only when Less than one
Read & Write Yes NE
SWITCHBACKFLA minute
G is set to
ENABLE.
Less than one

minute
CNOPERATORID
in an S1SERVIP
MO must be the
same as
CnOperatorId in a
Read & Write Yes eNodeB Less than 1 minute
configured
CnOperator MO.
Only one S1SIGIP
can be configured
for each operator.
S1SIGIP6ID in an
S1SigIP6 MO must
that in any other
S1SigIP6 MO.
SIGIP1 in an
S1SIGIP6 MO must
be the same as
IPV6 in a
configured DEVIP6
MO.
CN, SRN, and SN
in an S1SIGIP6 MO
Read & Write Yes NE
as those in the minute
IPITF6 MO
associated with
SIGIP1 in the
S1SIGIP6 MO.
If SIGIP1 in an
S1SIGIP6 MO must
be set to a global
unicast address.
same as IPV6 in a
configured DEVIP6
MO.
If SIGIKEIP in an
S1SIGIP6 MO is
valid, CN, SRN, and
SN in the S1SIGIP6
MO must be the
same as those in
the IPITF6 MO
SIGIKEIP.
If SIGIKEIP in an
S1SIGIP6 MO is
valid, it must be set
to a global unicast
address.
If SIGIKEIP in an
S1SIGIP6 MO is
valid, PT in the
IPITF6 MO
SIGIKEIP must be
set to ETH or
TRUNK.
If SIGIKEIP in an
S1SIGIP6 MO is
valid and PT in the
IPITF6 MO
associated with
SIGIP1 is not set to
LOOPINT, PN in the
IPITF6 MO
SIGIKEIP must be
the same as that in
the IPITF6
If SIGIP2 in an
S1SIGIP6 MO is
not 0:0:0:0:0:0:0:0,
it must be the same
as IPV6 in a
configured DEVIP6
MO.
In an S1SIGIP6
MO, SIGIP2 must
be different from
SIGIP1.
If SIGIP2 in an
S1SIGIP6 MO is
to a global unicast
address.
CN,SRN, and SN in
the IPITF6 MO
associated with
SIGIP2 in an
S1SigIP6 MO must
be the same as
those in the same
S1SigIP6MO.

same as IPV6 in a
configured DEVIP6
MO.
If SIGIKEIP2 in an
S1SIGIP6 MO is
valid, CN, SRN, and
SN in the S1SIGIP6
MO must be the
same as those in
the IPITF6 MO
SIGIKEIP2.
If SIGIKEIP2 in an
S1SIGIP6 MO is
to a global unicast
address.
If SIGIKEIP2 in an
S1SIGIP6 MO is
valid, PT in the
IPITF6 MO
SIGIKEIP2 must be
set to ETH or
TRUNK.
If SIGIKEIP2 in an
S1SIGIP6 MO is
valid and PT in the
IPITF6 MO
associated with
LOOPINT, PN in the
IPITF6 MO
SIGIKEIP2 must be
the same as that in
the IPITF6

In an S1SIGIP6
MO, RTOMIN must
be less than
RTOMAX.
In an S1SIGIP6
MO, RTOINIT must
be greater than or
equal to RTOMIN
and less than
RTOMAX.

In an S1SIGIP6
MO,
MAXASSOCRETR
must be greater
than
MAXPATHRETR.
MaxPathRetr must
be less than Read & Write Yes NE Less than 1 minute
MaxAssocRetr.

This parameter is
valid only when
SWITCHBACKFLA
G in the S1SigIP
MO is set to
ENABLE.
CNOPERATORID
in an S1SIGIP6 MO
must be the same
as CnOperatorId in
Less than one
a configured Read & Write Yes NE
minute
CnOperator MO.
Only one S1SIGIP6
can be configured
for each operator.
SGWID in an SGW
MO must be
any other SGW
MO.
set to LOOPINT,
and an SGW MO is
configured, the
eNodeB must be
configured with an
IP route that can
reach the SERVIP1
in the SGW MO or
with a DEVIP MO
that is on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPINT.
In an SGW MO,
SERVIP1 must be
different from
SERVIP2, Less than one
Read & Write Yes NE
SERVIP3, and minute
SERVIP4.
SERVIP1 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW MO.
SERVIP1 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured
Less than one
minute
If
SERVIP1IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP1IKEPEER Less than one
Read & Write Yes NE
NM in this MO must minute
be the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP1IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP1IPSECPR
Less than one
OPNM in this MO Read & Write Yes NE
minute
must be the same
as PROPNAME in
a configured
IPSECPROPOSAL
MO.
set to LOOPINT,
and SERVIP2 in an
SGW MO is not
0.0.0.0, the eNodeB
must be configured
can reach this
SERVIP2 or with a
DEVIP MO that is
on the same
network segment
as this SERVIP2
and has PT set to a
value other than
LOOPINT.
In an SGW MO,
SERVIP2 must be
different from
Read & Write Yes NE
SERVIP3, and minute
SERVIP4.
SERVIP2 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW MO.
SERVIP2 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured
Less than one
minute
If
SERVIP2IPSECFL
AG in an SGW MO
is set to ENABLE,
Read & Write Yes NE
be the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP2IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP2IPSECPR
Less than one
minute
must be the same
as PROPNAME in
a configured
IPSECPROPOSAL
MO.
set to LOOPINT,
and SERVIP3 in an
SGW MO is not
0.0.0.0, the eNodeB
must be configured
can reach this
SERVIP3 or with a
DEVIP MO that is
on the same
network segment
as this SERVIP3
and has PT set to a
value other than
LOOPINT.
In an SGW MO,
SERVIP3 must be
different from
Read & Write Yes NE
SERVIP2, and minute
SERVIP4.
SERVIP3 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW MO.
SERVIP3 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured
Less than one
minute
If
SERVIP3IPSECFL
AG in an SGW MO
is set to ENABLE,
Read & Write Yes NE
be the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP3IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP3IPSECPR
Less than one
minute
must be the same
as PROPNAME in
a configured
IPSECPROPOSAL
MO.
set to LOOPINT,
and SERVIP4 in an
SGW MO is not
0.0.0.0, the eNodeB
must be configured
can reach this
SERVIP4 or with a
DEVIP MO that is
on the same
network segment
as this SERVIP4
and has PT set to a
value other than
LOOPINT.
In an SGW MO,
SERVIP4 must be
different from
Read & Write Yes NE
SERVIP2, and minute
SERVIP3.
SERVIP4 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW MO.
SERVIP4 in an
SGW MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured
Less than one
minute
If
SERVIP4IPSECFL
AG in an SGW MO
is set to ENABLE,
Read & Write Yes NE
be the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP4IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP4IPSECPR
Less than one
minute
must be the same
as PROPNAME in
a configured
IPSECPROPOSAL
MO.
Less than one

minute
CNOPERATORID
in an SGW MO
Read & Write Yes NE
as CnOperatorId in minute
a configured
CnOperator MO.
SGWID in an
SGW6 MO must be
any other SGW6
MO.
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
an SGW6 MO is
configured, the
eNodeB must be
configured with an
IPv6 route that can
reach SERVIP1 in
the SGW6 MO or
with a DEVIP6 MO
that is on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPIF.
SERVIP1 in an
SGW6 MO must be
set to a global
unicast address.
In an SGW6 MO,
SERVIP1 must be
different from
SERVIP2,
SERVIP3, and
SERVIP4.
SERVIP1 in an
SGW6 MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW6 MO.
SERVIP1 in an
SGW6 MO must be
If
SERVIP1IPSECFL
AG in an SGW6
MO is set to
ENABLE,
Less than one
IKEPEERNM1 in Read & Write Yes NE
minute
this MO must be
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If
SERVIP2IPSECFL
AG in an SGW6
MO is set to
ENABLE,
IPSECPROPNM1 Less than one
Read & Write Yes NE
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
SERVIP2 in an
SGW6 MO is not
0:0:0:0:0:0:0:0, the
eNodeB must be
configured with an
IPv6 route that can
reach this SERVIP2
or with a DEVIP6
MO that is on the
same network
segment as this
SERVIP2 and has
PT set to a value
other than LOOPIF.
In an SGW6 MO,
SERVIP2 must be
different from
SERVIP1,
SERVIP3, and
SERVIP4.
SERVIP2 in an
SGW6 MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW6 MO.
SERVIP2 in an
SGW6 MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
If
SERVIP2IPSECFL
AG in an SGW6
MO is set to
ENABLE,
IKEPEERNM2 in Read & Write Yes NE Less than 1 minute
this MO must be
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If
SERVIP2IPSECFL
AG in an SGW6
MO is set to
ENABLE,
Read & Write Yes NE
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
SERVIP3 in an
SGW6 MO is not
0:0:0:0:0:0:0:0, the
eNodeB must be
configured with an
IPv6 route that can
reach this SERVIP3
or with a DEVIP6
MO that is on the
same network
segment as this
SERVIP3 and has
PT set to a value
other than LOOPIF.
In an SGW6 MO,
SERVIP3 must be
different from
SERVIP1,
SERVIP2, and
SERVIP4.
SERVIP3 in an
SGW6 MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW6 MO.
SERVIP3 in an
SGW6 MO must be
set to a global
unicast address.
SERVIP3 in an
SGW6 MO must be
If
SERVIP3IPSECFL
AG in an SGW6
MO is set to
ENABLE,
this MO must be
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If
SERVIP4IPSECFL
AG in an SGW6
MO is set to
ENABLE,
Read & Write Yes NE
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
SERVIP4 in an
SGW6 MO is not
0:0:0:0:0:0:0:0, the
eNodeB must be
configured with an
IPv6 route that can
reach this SERVIP4
or with a DEVIP6
MO that is on the
same network
segment as this
SERVIP4 and has
PT set to a value
other than LOOPIF.
In an SGW6 MO,
SERVIP4 must be
different from
SERVIP1,
SERVIP2, and
SERVIP3.
SERVIP4 in an
SGW6 MO must be
set to a global
unicast address.
SERVIP4 in an
SGW6 MO must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
other configured
SGW6 MO.
SERVIP4 in an
SGW6 MO must be
If
SERVIP4IPSECFL
AG in an SGW6
MO is set to
ENABLE,
this MO must be
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If
SERVIP4IPSECFL
AG in an SGW6
MO is set to
ENABLE,
Read & Write Yes NE
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
Less than one

minute
CNOPERATORID
in an SGW6 MO
must be the same
as CnOperatorId in
a configured
CnOperator MO.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
X2SERVIPID in an
X2ServIP MO must
that in any other
X2ServIP MO.
that is on the same
network segment
as this SERVIP2
and has PT set to a
value other than
LOOPINT.
If PT in the DEVIP
MO associated with
X2SERVIP in an
X2SERVIP MO is
set to LOOPINT,
and SERVIP3 in an
X2ENODEB MO is
not 0.0.0.0, the
local eNodeB must
be configured with
an IP route that can
reach this SERVIP3 No (And no impact
or with a DEVIP MO Read & Write on the UE in idle N/A N/A
that is on the same mode)
network segment
as this SERVIP3
and has PT set to a
value other than
LOOPINT.
If PT in the DEVIP
MO associated with
X2SERVIP in an
X2SERVIP MO is
set to LOOPINT,
and SERVIP4 in an
X2ENODEB MO is
not 0.0.0.0, the
local eNodeB must
be configured with
reach this SERVIP4
No (And no impact
mode)
In an X2ServIP
IPSECFLAG is set mode)
to ENABLE.
configured DEVIP
MO.
If LOCIKEIP in an
X2SERVIP MO is
same as IP in a
configured DEVIP
MO with PT set to
ETH or ETHTRK.
If LOCIKEIP in an
X2SERVIP MO is
valid and PT in the
DEVIP MO
associated with
X2SERVIP is not
set to LOOPINT, PN
in the DEVIP MO
No (And no impact
LOCIKEIP must be
the same as that
mode)
PN in the DEVIP
MO associated with
this X2SERVIP.
If LOCIKEIP in an
X2SERVIP MO is
valid, CN, SRN, and
SN in the
X2SERVIP MO
must be the same
as those in the
DEVIP MO
LOCIKEIP.
If LOCIKEIP in an
X2SERVIP MO is
valid, it must be a
valid IP address of
If IKEPEERNM in
an X2SERVIP MO
is valid, it must be No (And no impact
the same as Read & Write on the UE in idle N/A N/A
PEERNAME in a mode)
configured
IKEPEER MO.
If IPSECPROPNM
in an X2SERVIP
MO is valid, it must
No (And no impact
be the same as
PROPNAME in a
mode)
configured
IPSECPROPOSAL
MO.
No (And no impact
mode)
CNOPERATORID
in an X2SERVIP
MO must be the No (And no impact
same as Read & Write on the UE in idle N/A N/A
CnOperatorId in a mode)
configured
CnOperator MO.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
X2SIGIPID in an
X2SigIP MO must
that in any other
X2SigIP MO.
LOCIP in an
X2SIGIP MO must
be the same as IP
in a configured
DEVIP MO.
If LOCIP in an
X2SIGIP MO is
to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
CN, SRN, and SN
in an X2SIGIP MO
must be the same
as those in the
DEVIP MO No (And no impact
associated with Read & Write on the UE in idle N/A N/A
LOCIP in the mode)
X2SIGIP MO.
If
ENodeBSharingM
ode in the
ENodeBSharingM
ode MO is set to
SEPARATED_FRE
Q, LOCIP in an
X2SIGIP MO
cannot be the same
as LOCIP or
SECLOCIP in
another X2SIGIP
MO with the same
LOCPORT but a
different
CNOPERATORID.
No (And no impact
mode)
In an X2SigIP MO,
this parameter is No (And no impact
valid only when Read & Write on the UE in idle N/A N/A
to ENABLE.
MO.
If IKEIP in an
X2SIGIP MO is
to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
If IKEIP in an
X2SIGIP MO is
valid and PT in the
DEVIP MO
associated with
LOCIP is not set to
LOOPINT, PN in the
DEVIP MO
associated with this No (And no impact
IKEIP must be the Read & Write on the UE in idle N/A N/A
same as that in the mode)
DEVIP MO
LOCIP.
If IKEIP in an
X2SIGIP MO is
valid, PT in the
DEVIP MO
IKEIP can only be
set to ETH or
ETHTRK.
If IKEIP in an
X2SIGIP MO is
valid, the
combination of CN,
SRN, and SN in the
X2SIGIP MO must
If IKEPEERNM in
an X2SIGIP MO is
valid, it must be the No (And no impact
PEERNAME in a mode)
configured
IKEPEER MO.
If IPSECPROPNM
in an X2SIGIP MO
is valid, it must be
No (And no impact
the same as
PROPNAME in a
mode)
configured
IPSECPROPOSAL
MO.
configured DEVIP
MO.
If SECLOCIP in an
X2SIGIP MO is not
0.0.0.0, it must be
set to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
If SECLOCIP in an
X2SIGIP MO is not
0.0.0.0, it must be
different from
LOCIP.
If SECLOCIP in an
X2SIGIP MO is not
0.0.0.0, CN, SRN, No (And no impact
and SN in the Read & Write on the UE in idle N/A N/A
X2SIGIP MO must mode)
be the same as
those in the DEVIP
MO associated with
this SECLOCIP.
If
ENodeBSharingM
ode in the
ENodeBSharingM
ode MO is set to
SEPARATED_FRE
Q, SECLOCIP in an
X2SIGIP MO
cannot be the same
as LOCIP or
SECLOCIP in
another configured
X2SIGIP MO with
No (And no impact
mode)
In an X2SigIP MO,
SECIPSECFLAG is mode)
set to ENABLE.
configured DEVIP
MO.
If SECLOCIKEIP in
an X2SIGIP MO is
to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
If SECLOCIKEIP in
an X2SIGIP MO is
valid, CN, SRN, and
SN in the X2SIGIP
MO must be the
same as those in
the DEVIP MO
No (And no impact
SECLOCIKEIP.
If SECLOCIKEIP in
mode)
an X2SIGIP MO is
valid and PT in the
DEVIP MO
associated with
SECLOCIP is not
set to LOOPINT, PN
in the DEVIP MO
SECLOCIKEIP
must be the same
as that in the
DEVIP MO
SECLOCIP.
If SECLOCIKEIP in
an X2SIGIP MO is
valid, PT in the
DEVIP MO
If SECIKEPEERNM
in an X2SIGIP MO
PEERNAME in a mode)
configured
IKEPEER MO.
If
SECIPSECPROPN
M in an X2SIGIP
MO is valid, it must No (And no impact
be the same as Read & Write on the UE in idle N/A N/A
PROPNAME in a mode)
configured
IPSECPROPOSAL
MO.
If the
ENodeBSharingM
ode parameter in
the
ENodeBSharingM
ode MO is set to
SHARED_FREQ,
No (And no impact
LOCIP and
SECLOCIP in an
mode)
X2SIGIP MO must
be the same as or
different from those,
respectively, in
another X2SIGIP
MO with the same
value of LOCPORT.
No (And no impact
mode)
In an X2SIGIP MO,
No (And no impact
RTOMAX must be
greater than
mode)
RTOMIN.
In an X2SIGIP MO,
RTOINIT must be
No (And no impact
greater than or
equal to RTOMIN
mode)
and less than
RTOMAX.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an X2SIGIP MO,
MAXASSOCRETR No (And no impact
must be greater Read & Write on the UE in idle N/A N/A
than mode)
MAXPATHRETR.
In an X2SigIP MO,
No (And no impact
MaxPathRetr must
be smaller than
mode)
MaxAssocRetr.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
SWITCHBACKHB
NUM is valid only
No (And no impact
when
SWITCHBACKFLA
mode)
G is set to
ENABLE.
SWITCHBACKHB
NUM is valid only
No (And no impact
when
SWITCHBACKFLA
mode)
G is set to
ENABLE.
No (And no impact
mode)
CNOPERATORID
in an X2SIGIP MO
must be the same
as CnOperatorId in
a configured Read & Write Yes eNodeB Less than 1 minute
CnOperator MO.
Only one X2SIGIP
can be configured
for each operator.
X2ENODEBID in an
X2eNodeB MO
must be different
from that in any
other X2eNodeB
MO.
FIRSTSIGIP in an
X2ENODEB MO
must be different
from IP in any
configured DEVIP
MO.
FIRSTSIGIP in an
X2ENODEB MO
cannot be the same
as FIRSTSIGIP or
SECSIGIP in any
other configured
X2ENODEB MO
owned by the same
No (And no impact
operator.
FIRSTSIGIP in an
mode)
X2ENODEB MO
must be different
from FIRSTSIGIP
and SECSIGIP in
any configured
MME MO.
FIRSTSIGIP in an
X2ENODEB MO
must be set to a
valid IP address of
addition, it cannot
be set to 127.x.x.x
or 0.x.x.x.
No (And no impact
mode)
In an X2eNodeB
FIRSTIPSECFLAG mode)
is set to ENABLE.
If FIRSTIKEIP in an
X2ENODEB MO is
valid, it must be
any configured
DEVIP MO.
No (And no impact
If FIRSTIKEIP in an
X2ENODEB MO is
mode)
valid, it must be a
valid IP address of
addition, it cannot
be set to 127.x.x.x
or 0.x.x.x.
If SECSIGIP in an
X2ENODEB MO is
not 0.0.0.0, it must
be different from IP
in any configured
DEVIP MO.
If SECSIGIP in an
X2ENODEB MO is
be set to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
In an X2ENODEB
MO, if SECSIGIP is
be different from No (And no impact
FIRSTSIGIP. Read & Write on the UE in idle N/A N/A
If SECSIGIP in an mode)
X2ENODEB MO is
valid, it cannot be
the same as
FIRSTSIGIP or
SECSIGIP in any
other configured
X2ENODEB MO
owned by the same
operator.
If SECSIGIP in an
X2ENODEB MO is
be different from
FIRSTSIGIP and
SECSIGIP in any
other configured
MME MO.
No (And no impact
mode)
In an X2eNodeB
SECIPSECFLAG is mode)
set to ENABLE.
If SECIKEIP in an
X2ENODEB MO is
valid, it must be
any configured
DEVIP MO.
No (And no impact
If SECIKEIP in an
X2ENODEB MO is
mode)
to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
FIRSTSIGIP and
SECSIGIP in an
X2ENODEB MO
must be both the
same as or both
No (And no impact
different from those
in another
mode)
X2ENODEB MO
with the same
APPPORT but a
different
CNOPERATORID.
not 0.0.0.0, the
local eNodeB must
be configured with
reach this SERVIP1
or with a DEVIP MO
that is on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPINT.
If SERVIP1 in an
X2ENODEB MO is
address of Class A,
B, or C. In addition, No (And no impact
this IP address Read & Write on the UE in idle N/A N/A
cannot be set to mode)
127.x.x.x or 0.x.x.x.
If SERVIP1 In an
X2ENODEB MO is
be different from
SERVIP2,
SERVIP3, and
SERVIP4.
If SERVIP1 in an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW
No (And no impact
mode)
In an X2eNodeB
MO, this parameter
No (And no impact
is valid only when
SERVIP1IPSECFL
mode)
AG is set to
ENABLE.
If SERVIP1IKEIP in
an X2ENODEB MO
any configured
DEVIP MO.
No (And no impact
If SERVIP1IKEIP in
an X2ENODEB MO
mode)
set to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
not 0.0.0.0, the
local eNodeB must
be configured with
reach this SERVIP2
or with a DEVIP MO
that is on the same
network segment
as this SERVIP2
and has PT set to a
value other than
LOOPINT.
If SERVIP2 in an
X2ENODEB MO is
address of Class A,
127.x.x.x or 0.x.x.x.
If SERVIP2 In an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP3, and
SERVIP4.
If SERVIP2 in an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW
No (And no impact
mode)
In an X2eNodeB
MO, this parameter
No (And no impact
is valid only when
SERVIP2IPSECFL
mode)
AG is set to
ENABLE.
If SERVIP2IKEIP in
an X2ENODEB MO
any configured
DEVIP MO.
No (And no impact
If SERVIP2IKEIP in
an X2ENODEB MO
mode)
set to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
not 0.0.0.0, the
local eNodeB must
be configured with
reach this SERVIP3
or with a DEVIP MO
that is on the same
network segment
as this SERVIP3
and has PT set to a
value other than
LOOPINT.
If SERVIP3 in an
X2ENODEB MO is
address of Class A,
127.x.x.x or 0.x.x.x.
If SERVIP3 In an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP2, and
SERVIP4.
If SERVIP3 in an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW
No (And no impact
mode)
In an X2eNodeB
MO, this parameter
No (And no impact
is valid only when
SERVIP3IPSECFL
mode)
AG is set to
ENABLE.
If SERVIP3IKEIP in
an X2ENODEB MO
any configured
DEVIP MO.
No (And no impact
If SERVIP3IKEIP in
an X2ENODEB MO
mode)
set to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
not 0.0.0.0, the
local eNodeB must
be configured with
reach this SERVIP4
or with a DEVIP MO
that is on the same
network segment
as this SERVIP4
and has PT set to a
value other than
LOOPINT.
If SERVIP4 in an
X2ENODEB MO is
address of Class A,
127.x.x.x or 0.x.x.x.
If SERVIP4 In an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP2, and
SERVIP3.
If SERVIP4 in an
X2ENODEB MO is
be different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW
No (And no impact
mode)
In an X2eNodeB
MO, this parameter
No (And no impact
is valid only when
SERVIP4IPSECFL
mode)
AG is set to
ENABLE.
If SERVIP4IKEIP in
an X2ENODEB MO
any configured
DEVIP MO.
No (And no impact
If SERVIP4IKEIP in
an X2ENODEB MO
mode)
set to a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
If MCC in an
X2ENODEB MO is No (And no impact
valid, its value must Read & Write on the UE in idle N/A N/A
consist of three mode)
digits.
If MNC in an
X2ENODEB MO is No (And no impact
consist of two to mode)
three digits.
No (And no impact
mode)
No (And no impact
mode)
CNOPERATORID
in an X2ENODEB
configured
CnOperator MO.
No (And no impact
mode)
X2ServIP6ID in an
X2ServIP6 MO
must be different
from that in any
other X2ServIP6
MO.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
with an IPv6 route
that can reach this
SERVIP2 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP2
and has PT set to a
value other than
LOOPIF.
If PT in the IPITF6
MO associated with
SERVIP in an
X2SERVIP6 MO is
set to LOOPIF, and
SERVIP3 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
No (And no impact
the local eNodeB
must be configured
mode)
with an IPv6 route
that can reach this
SERVIP3 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP3
and has PT set to a
value other than
LOOPIF.
If PT in the IPITF6
MO associated with
SERVIP in an
X2SERVIP6 MO is
set to LOOPIF, and
SERVIP4 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
No (And no impact
mode)
In an X2eNodeB
to ENABLE.

same as IPV6 in a
configured DEVIP6
MO.
If SERVIKEIP in an
X2SERVIP6 MO is
valid, CN, SRN, and
SN in the
X2SERVIP6 MO
must be the same
as those in the
IPITF6 MO
SERVIKEIP.
If SERVIKEIP in an
X2SERVIP6 MO is
to a global unicast
No (And no impact
address.
If SERVIKEIP in an
mode)
X2SERVIP6 MO is
same as IP in a
configured DEVIP
MO with PT set to
ETH or TRUNK.
If SERVIKEIP in an
X2SERVIP6 MO is
valid and PT in the
IPITF6 MO
associated with
SERVIP is not set
to LOOPINT, PN in
the IPITF6 MO
SERVIKEIP must
be the same as that
in the IPITF6 MO
If IKEPEERNM in
an X2SERVIP6 MO
PEERNAME in a mode)
configured
IKEPEER6 MO.
If IPSECPROPNM
in an X2SERVIP6
No (And no impact
be the same as
PROPNAME in a
mode)
configured
IPSECPROPOSAL
MO.
No (And no impact
mode)
CNOPERATORID
in an X2SERVIP6
configured
CnOperator MO.
X2SIGIP6ID in an
X2SigIP6 MO must
that in any other
X2SigIP6 MO.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
SIGIP1 in an
X2SIGIP6 MO must
be the same as
IPV6 in a
configured DEVIP6
MO.
CN, SRN, and SN
in an X2SIGIP6 MO
must be the same
as those in the
IPITF6 MO
associated with
SIGIP1 in the
X2SIGIP6 MO.
If
ENodeBSharingM
No (And no impact
ode in the
ENodeBSharingM
mode)
ode MO is set to
SEPARATED_FRE
Q, SIGIP1 in an
X2SIGIP6 MO
cannot be the same
as SIGIP1 or
SIGIP2 in another
X2SIGIP6 MO with
the same
LOCPORT but a
different
CNOPERATORID.
SIGIP1 in an
X2SIGIP6 MO must
be a global unicast
address.
No (And no impact
mode)
In an X2SIGIP6
SIGIP1SECFLAG mode)
is set to ENABLE.
same as IPV6 in a
configured DEVIP6
MO.
If SIGIKEIP1 in an
X2SIGIP6 MO is
valid, CN, SRN, and
SN in the X2SIGIP6
MO must be the
same as those in
the IPITF6 MO
SIGIKEIP1.
If SIGIKEIP1 in an
X2SIGIP6 MO is
valid, it must be a
global unicast
address.
No (And no impact
If SIGIKEIP1 in an
X2SIGIP6 MO is
mode)
valid, PT in the
IPITF6 MO
SIGIKEIP1 must be
set to ETH or
TRUNK.
If SIGIKEIP1 in an
X2SERVIP6 MO is
valid and PT in the
IPITF6 MO
associated with
LOOPINT, PN in the
IPITF6 MO
SIGIKEIP1 must be
the same as that in
the IPITF6 MO
If IKEPEERNM1 in
an X2SIGIP6 MO is
PEERNAME in a mode)
configured
IKEPEER6 MO.
If IPSECPROPNM1
in an X2SIGIP6 MO
No (And no impact
the same as
PROPNAME in a
mode)
configured
IPSECPROPOSAL
MO.
be the same as
IPV6 in a
configured DEVIP6
MO.
If SIGIP2 in an
X2SIGIP6 MO is
not 0::0, CN, SRN,
and SN in the
X2SIGIP6 MO must
be the same as
those in the IPITF6
MO associated with
this SIGIP2.
If
ENodeBSharingM
ode in the
ENodeBSharingM
ode MO is set to No (And no impact
SEPARATED_FRE Read & Write on the UE in idle N/A N/A
Q, SIGIP2 in an mode)
X2SIGIP6 MO
cannot be the same
as SIGIP1 or
SIGIP2 in another
X2SIGIP6 MO with
the same
LOCPORT but a
different
CNOPERATORID.
If SIGIP2 in an
X2SIGIP6 MO is
not 0::0, it must be
a global unicast
address.
In an X2SIGIP6
MO, if SIGIP2 is not
0::0, it must be
No (And no impact
mode)
In an X2SIGIP6
SIGIP2SECFLAG mode)
is set to ENABLE.
same as IPV6 in a
configured DEVIP6
MO.
If SIGIKEIP2 in an
X2SIGIP6 MO is
valid, CN, SRN, and
SN in the X2SIGIP6
MO must be the
same as those in
the IPITF6 MO
SIGIKEIP2.
If SIGIKEIP2 in an
X2SIGIP6 MO is
valid, it must be a
global unicast
address.
No (And no impact
If SIGIKEIP2 in an
X2SIGIP6 MO is
mode)
valid, PT in the
IPITF6 MO
SIGIKEIP2 must be
set to ETH or
TRUNK.
If SIGIKEIP2 in an
X2SERVIP6 MO is
valid and PT in the
IPITF6 MO
associated with
LOOPINT, PN in the
IPITF6 MO
SIGIKEIP2 must be
the same as that in
the IPITF6 MO
If IKEPEERNM2 in
an X2SIGIP6 MO is
PEERNAME in a mode)
configured
IKEPEER6 MO.
If IPSECPROPNM2
in an X2SIGIP6 MO
No (And no impact
the same as
PROPNAME in a
mode)
configured
IPSECPROPOSAL
MO.
If the
ENodeBSharingM
ode parameter in
the
ENodeBSharingM
ode MO is set to
SHARED_FREQ,
No (And no impact
SIGIP1 and SIGIP2
in an X2SIGIP6 MO
mode)
must be the same
as or different from
those, respectively,
in another
X2SIGIP6 MO with
the same value of
LOCPORT.
No (And no impact
mode)
In an X2SIGIP6
No (And no impact
MO, RTOMAX must
be greater than
mode)
RTOMIN.
In an X2SIGIP6
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and less than
RTOMAX.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an X2SIGIP6
MO,
No (And no impact
MAXASSOCRETR
must be greater
mode)
than
MAXPATHRETR.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
SWITCHBACKHBN
UM is valid only
No (And no impact
when
SWITCHBACKFLA
mode)
G is set to
ENABLE.
CNOPERATORID
in an X2SIGIP6 MO
must be the same
as CnOperatorId in No (And no impact
a configured Read & Write on the UE in idle N/A N/A
CnOperator MO. mode)
Only one X2SIGIP6
can be configured
for each operator.
X2ENODEBID in an
X2eNodeB6 MO
must be different
from that in any
other X2eNodeB6
MO.
SIGIP1 in an
X2ENODEB6 MO
must be different
from IPV6 in any
configured DEVIP6
MO.
SIGIP1 in an
X2ENODEB6 MO
must be set to a
global unicast
address.
SIGIP1 in an
X2ENODEB6 MO No (And no impact
must be different Read & Write on the UE in idle N/A N/A
from SIGIP1 and mode)
SIGIP2 in any
configured MME6
MO.
SIGIP1 in an
X2ENODEB6 MO
cannot be the same
as SIGIP1 or
SIGIP2 in any other
configured
X2ENODEB6 MO
owned by the same
operator.
No (And no impact
mode)
In an X2ENODEB6
SIGIP1SECFLAG mode)
is set to ENABLE.
If SIGIKEIP1 in an
X2ENODEB6 MO is
valid, it must be
different from IPV6
in any configured No (And no impact
DEVIP6 MO. Read & Write on the UE in idle N/A N/A
If SIGIKEIP1 in an mode)
X2ENODEB6 MO is
to a global unicast
address.
If SIGIP2 in an
X2ENODEB6 MO is
valid, it must be
different from IPV6
in any configured
DEVIP6 MO.
If SIGIP2 in an
X2ENODEB6 MO is
to a global unicast
address.
If SIGIP2 in an
X2ENODEB6 MO is
valid, it must be
different from
SIGIP1 and SIGIP2 No (And no impact
in any configured Read & Write on the UE in idle N/A N/A
MME6 MO. mode)
In an X2ENODEB6
MO, if SIGIP2 is
valid, it must be
different from
SIGIP1.
If SIGIP2 in an
X2ENODEB6 MO is
valid, it cannot be
the same as
SIGIP1 or SIGIP2
in any other
configured
X2ENODEB6 MO
owned by the same
operator.
No (And no impact
mode)
In an X2ENODEB6
SIGIP2SECFLAG mode)
is set to ENABLE.
If SIGIKEIP2 in an
X2ENODEB6 MO is
valid, it must be
different from IPV6
in any configured No (And no impact
DEVIP6 MO. Read & Write on the UE in idle N/A N/A
If SIGIKEIP2 in an mode)
X2ENODEB6 MO is
to a global unicast
address.
SIGIP1 and SIGIP2
in an X2ENODEB6
MO must be the
same as or different
No (And no impact
from those,
respectively, in
mode)
another
X2ENODEB6 MO
with the same value
of LOCPORT.
SERVIP1 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
the local eNodeB
must be configured
with an IPv6 route
that can reach this
SERVIP1 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPIF.
If SERVIP1 in an
X2ENODEB6 MO is
valid, it must be set No (And no impact
to a global unicast Read & Write on the UE in idle N/A N/A
address. mode)
In an X2ENODEB6
MO, SERVIP1 must
be different from
SERVIP2,
SERVIP3, and
SERVIP4.
If SERVIP1 in an
X2ENODEB6 MO is
valid, it must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW6
MO.
If SERVIP1 in an
No (And no impact
mode)
In an X2ENODEB6
MO, this parameter
No (And no impact
is valid only when
SERVIP1IPSECFL
mode)
AG is set to
ENABLE.
If SERVIKEIP1 in
an X2ENODEB6
be different from
IPV6 in any
No (And no impact
configured DEVIP6
MO.
mode)
If SERVIKEIP1 in
an X2ENODEB6
be set to a global
unicast address.
SERVIP2 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
the local eNodeB
must be configured
with an IPv6 route
that can reach this
SERVIP2 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP2
and has PT set to a
value other than
LOOPIF.
If SERVIP2 in an
X2ENODEB6 MO is
address. mode)
In an X2ENODEB6
MO, SERVIP2 must
be different from
SERVIP1,
SERVIP3, and
SERVIP4.
If SERVIP2 in an
X2ENODEB6 MO is
valid, it must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW6
MO.
If SERVIP2 in an
No (And no impact
mode)
In an X2ENODEB6
MO, this parameter
No (And no impact
is valid only when
SERVIP2IPSECFL
mode)
AG is set to
ENABLE.
If SERVIKEIP2 in
an X2ENODEB6
be different from
IPV6 in any
No (And no impact
configured DEVIP6
MO.
mode)
If SERVIKEIP2 in
an X2ENODEB6
be set to a global
unicast address.
SERVIP3 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
the local eNodeB
must be configured
with an IPv6 route
that can reach this
SERVIP3 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP3
and has PT set to a
value other than
LOOPIF.
If SERVIP3 in an
X2ENODEB6 MO is
address. mode)
In an X2ENODEB6
MO, SERVIP3 must
be different from
SERVIP1,
SERVIP2, and
SERVIP4.
If SERVIP3 in an
X2ENODEB6 MO is
valid, it must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW6
MO.
If SERVIP3 in an
No (And no impact
mode)
In an X2ENODEB6
MO, this parameter
No (And no impact
is valid only when
SERVIP3IPSECFL
mode)
AG is set to
ENABLE.
If SERVIKEIP3 in
an X2ENODEB6
be different from
IPV6 in any
No (And no impact
configured DEVIP6
MO.
mode)
If SERVIKEIP3 in
an X2ENODEB6
be set to a global
unicast address.
SERVIP4 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
the local eNodeB
must be configured
with an IPv6 route
that can reach this
SERVIP4 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP4
and has PT set to a
value other than
LOOPIF.
If SERVIP4 in an
X2ENODEB6 MO is
address. mode)
In an X2ENODEB6
MO, SERVIP4 must
be different from
SERVIP1,
SERVIP2, and
SERVIP3.
If SERVIP4 in an
X2ENODEB6 MO is
valid, it must be
different from
SERVIP1,
SERVIP2,
SERVIP3, and
SERVIP4 in any
configured SGW6
MO.
If SERVIP4 in an
No (And no impact
mode)
In an X2ENODEB6
MO, this parameter
No (And no impact
is valid only when
SERVIP4IPSECFL
mode)
AG is set to
ENABLE.
If SERVIKEIP4 in
an X2ENODEB6
be different from
IPV6 in any
No (And no impact
configured DEVIP6
MO.
mode)
If SERVIKEIP4 in
an X2ENODEB6
be set to a global
unicast address.
If MCC in an
X2ENODEB6 MO is No (And no impact
consist of three mode)
digits.
If MNC in an
X2ENODEB6 MO is No (And no impact
consist of two to mode)
three digits.
No (And no impact
mode)
No (And no impact
mode)
CNOPERATORID
in an X2ENODEB6
configured
CnOperator MO.
No (And no impact
mode)
URL in a CA MO
must begin with http
or https, the IP
No (And no impact
address must be a
valid IP address,
mode)
and the port
number must range
from 1 to 65535.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
USERADDINFO in
a CERTREQ MO
must contain only
No (And no impact
printable ASCII
characters (the
mode)
ASCII value within
the range of 32 to
127).
COUNTRY in a
CERTREQ MO
must contain only
the following
printable ASCII
No (And no impact
characters: A~Z a~z
' ( ) + , - . / 0~9 :
mode)
= ?.
The string length of
COUNTRY in a
CERTREQ MO
must be 0 or 2.
ORG in a
CERTREQ MO
must contain only
No (And no impact
printable ASCII
characters (the
mode)
ASCII value within
the range of 32 to
127).
ORGUNIT in a
CERTREQ MO
must contain only
No (And no impact
printable ASCII
characters (the
mode)
ASCII value within
the range of 32 to
127).
STATEPROVINCE
NAME in a
CERTREQ MO
must contain only No (And no impact
printable ASCII Read & Write on the UE in idle N/A N/A
characters (the mode)
ASCII value within
the range of 32 to
127).
LOCALITY in a
CERTREQ MO
must contain only
No (And no impact
printable ASCII
characters (the
mode)
ASCII value within
the range of 32 to
127).
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
LOCALNAME in a
CERTREQ MO
must contain only
No (And no impact
printable ASCII
characters (the
mode)
ASCII value within
the range of 32 to
127).
LOCALIP in a
CERTREQ MO
must be a valid IP
address of class A,
No (And no impact
it cannot be set to
mode)
the reserved IP
addresses 127.x.x.x
or 0.x.x.x but can
be set to 0.0.0.0.
The CERTMK MO
with APPCERT set
to appcert.pem
defines a certificate
configured on a BS
before delivery.
There is only one
such MO on a BS
and this MO cannot
be added or
removed.
APPCERT in a Read Only N/A N/A N/A
CERTMK MO can
contain only ASCII
characters. The
name must not
contain spaces or
the following
characters: \ / : * ? "
< > |.
APPCERT in a
CERTMK MO is
case insensitive.

On a BS, there is
only one activated
device certificate for Read Only N/A N/A N/A
each application
type.
APPCERT in an
APPCERT MO can
contain only ASCII
characters. The No (And no impact
name must not Read & Write on the UE in idle N/A N/A
contain spaces or mode)
the following
< > |.

No (And no impact
mode)
CERTNAME in a
CROSSCERT MO
can contain only
ASCII characters.
The name must not
contain spaces or
the following
< > |.
CERTNAME in a
CROSSCERT MO
is case insensitive.

On a BS, there is
only one
TRUSTCERT MO
with CERTNAME
set to caroot.pem.
CERTNAME in a
TRUSTCERT MO
can contain only
ASCII characters. Read Only N/A N/A N/A
The name must not
contain spaces or
the following
< > |.
CERTNAME in a
TRUSTCERT MO is
case insensitive.

CERTNAME in a
CRL MO can
contain only ASCII
characters. The
name must not
contain spaces or
the following
< > |.
CERTNAME in a
CRL MO is case
insensitive.
IP in a CRLTSK
MO must be set to
a valid IP address
of class A, B, or C.
In addition, It
cannot be set to
127.x.x.x or 0.x.x.x
(including 0.0.0.0).

This parameter is
valid only when
CRLGETMETHOD
in the same
CRLTSK MO is set
to LDAP.
Each CRLTSK MO
must have a unique
FILENAME and
FILENAME in a
CRLTSK MO is
case insensitive.
FILENAME in a
CRLTSK MO can Read Only N/A N/A N/A
contain only ASCII
characters. The
name must not
contain spaces or
the following
< > |.

This parameter is
valid only when
CRLGETMETHOD
in the same
CRLTSK MO is set
to LDAP.
SIP must be a valid

IP address of class
A, B, or C. In
addition, it cannot
be set to the
reserved IP
addresses 0.x.x.x
or 127.x.x.x, but
can be set to
0.0.0.0.
No (And no impact
mode)
In a CERTCHKTSK
No (And no impact
MO, PERIOD must
be smaller than
mode)
ALMRNG.
In a CERTCHKTSK
No (And no impact
MO, PERIOD must
be smaller than
mode)
ALMRNG.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

This parameter is
valid only when
ACLID in the
ACLRULE MO is
within the range of
3000 to 3999.
Services are
parameter is
correctly set.
Services are
parameter is
correctly set.
In an ACLRULE
MO, MFRG and
SMPT must not be
both set to YES.
In the ACLRULE Read Only N/A N/A N/A
MO, this parameter
is valid only when
PT is set to TCP,
UDP, or SCTP.
In the ACLRULE
MO, this parameter
is valid only when Read Only N/A N/A N/A
SMPT is set to
YES.
In an ACLRULE
MO, if SOP is set to
OP_RANGE, SPT1
must be smaller
than or equal to
SPT2. Read Only N/A N/A N/A
In the ACLRULE
MO, this parameter
is valid only when
SMPT is set to
YES.
In an ACLRULE
OP_RANGE, SPT1
must be smaller
than or equal to
SPT2.
In the ACLRULE
MO, this parameter
is valid only when
SMPT is set to YES
and SOP is set to
OP_RANGE.
Services are
parameter is
correctly set.
Services are
parameter is
correctly set.
In an ACLRULE
MO, MFRG and
DMPT must not be
both set to YES.
In the ACLRULE Read Only N/A N/A N/A
MO, this parameter
is valid only when
PT is set to TCP,
UDP, or SCTP.
In the ACLRULE
MO, this parameter
DMPT is set to
YES.
In an ACLRULE
MO, if DOP is set to
OP_RANGE, DPT1
must be smaller
than or equal to
DPT2. Read Only N/A N/A N/A
In the ACLRULE
MO, this parameter
is valid only when
DMPT is set to
YES.
In an ACLRULE
OP_RANGE, DPT1
must be smaller
than or equal to
DPT2. Read Only N/A N/A N/A
In the ACLRULE
MO, this parameter
is valid only when
DOP is set to
OP_RANGE.
In the ACLRULE
MO, this parameter
MDSCP is set to
YES.
In an ACLRULE
MO, MFRG and
SMPT must not be
both set to YES.
In an ACLRULE
MO, MFRG and
DMPT must not be Read Only N/A N/A N/A
both set to YES.
In the ACLRULE
MO, this parameter
is valid only when
PT is set to a valid
value.
This parameter is
valid only when Services are
ACLID in the interrupted until the
Read & Write Yes BS
ACLRULE MO is parameter is
within the range of correctly set.
4000 to 4999.
If ACLID ranges
from 4000 to 4999
Services are
and VLANIDOP is
set to OP_RANGE, Read & Write Yes BS
parameter is
VLANID1 must be
correctly set.
smaller than
VLANID2.
If ACLID ranges
from 4000 to 4999
Services are
and VLANIDOP is
set to OP_RANGE, Read & Write Yes BS
parameter is
VLANID1 must be
correctly set.
smaller than
VLANID2.

Services are
parameter is
correctly set.
Services are
parameter is
correctly set.
In an ACLRULE6
MO, this parameter
is valid when PT is Read Only N/A N/A N/A
set to TCP, UDP, or
SCTP.
In an ACLRULE6
MO, this parameter
is valid when PT is
set to TCP, UDP, or
SCTP and SMPT is
set to YES.
In an ACLRULE6
OP_RANGE, SPT1
must be smaller
than SPT2.
In an ACLRULE6 Read Only N/A N/A N/A
MO, this parameter
is valid when PT is
set to TCP, UDP, or
SCTP and SMPT is
set to YES.
In an ACLRULE6
OP_RANGE, SPT1
must be smaller
than SPT2.
In an ACLRULE6
MO, this parameter
is valid when PT is
set to TCP, UDP, or
SCTP, SMPT is set
to YES, and SOP is
set to OP_RANGE.
Services are
parameter is
correctly set.
Services are
parameter is
correctly set.
In an ACLRULE6
MO, this parameter
is valid when PT is Read Only N/A N/A N/A
set to TCP, UDP, or
SCTP.
In an ACLRULE6
MO, this parameter
is valid when PT is
set to TCP, UDP, or
SCTP and DMPT is
set to YES.
In an ACLRULE6
OP_RANGE, DPT1
must be smaller
than DPT2,
respectively.
In an ACLRULE6
MO, this parameter
is valid when PT is
set to TCP, UDP, or
SCTP and DMPT is
set to YES.
In an ACLRULE6
OP_RANGE, DPT1
must be smaller
than DPT2,
respectively.
In an ACLRULE6 Read Only N/A N/A N/A
MO, this parameter
is valid when PT is
set to TCP, UDP, or
SCTP, DMPT is set
to YES, and DOP is
set to OP_RANGE.
In an ACLRULE6
MO, this parameter
is valid when Read Only N/A N/A N/A
MDSCP is set to
YES.

SRCIP in a
BFDSESSION MO
must be a valid IP
address of class A,
it cannot be set to
SRCIP must be
different from
DSTIP in a
BFDSESSION MO.
DSTIP in a
BFDSESSION MO
must be a valid IP
address of class A,
it cannot be set to
SRCIP must be
different from
DSTIP in a
BFDSESSION MO.
In the
BFDSESSION MO,
if SRCIP is set to a
logical IP address,
HT cannot be set to
SINGLE_HOP.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)


No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the CFMBNDIP
MO, the total length
of MANAME and Read Only N/A N/A N/A
MDNAME cannot
exceed 44 bytes.
MANAME in a
CFMBNDIP MO
can contain only
ASCII characters.
The name cannot
be null characters
or contain the
following Read Only N/A N/A N/A
characters: ', ", !, ?,
<, >, and \.
In the CFMBNDIP
of MANAME and
MDNAME cannot
exceed 44 bytes.

In the CFMMA MO,

the total length of
MANAME and Read Only N/A N/A N/A
MDNAME cannot
exceed 44 bytes.
MANAME in a
CFMMA MO can
contain only ASCII
characters. The
name cannot be
null characters or
contain the
<, >, and \.
In the CFMMA MO,
the total length of
MANAME and
MDNAME cannot
exceed 44 bytes.
In the CFMMA MO,

this parameter is
valid only when Read Only N/A N/A N/A
BNDVLAN is set to
YES.
In the CFMMA MO,
BNDVLAN is set to mode)
YES.
No (And no impact
mode)

MDNAME in a
CFMMD MO can
contain only ASCII
characters. The
name cannot be
null characters or
contain the
following
<, >, and \.
In the CFMMEP
MDNAME cannot
exceed 44 bytes.
In the CFMMEP
of MANAME and
MDNAME cannot
exceed 44 bytes.
MANAME in a
CFMMEP MO can
contain only ASCII Read Only N/A N/A N/A
characters. The
name cannot be
null characters or
contain the
following
<, >, and \.

In a CFMMEP MO,
this parameter must
be set to
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In a CFMMEP MO,
this parameter can
be set to
BASE_BOARD or
ETH_COVERBOAR
D if SN is set to 6 or
7.
In the CFMMEP
MO, if PT is set to
ETH and SBT is set
to
ETH_COVERBOAR
D, the value range
from 0 to 5.
In the CFMMEP
MO, if PT is set to
ETH and SBT is set
to BASE_BOARD,
this parameter can
be set to 0 or 1.
In the CFMMEP Read Only N/A N/A N/A
MO, if PT is set to
ETHTRK and SBT
is set to
BASE_BOARD, this
parameter can be
set to 0 or 1.
In the CFMMEP
MO, if PT is set to
ETHTRK and SBT
is set to
ETH_COVERBOAR
D, the value range
from 0 to 2.

In the CFMRMEP
MDNAME cannot
exceed 44 bytes.
MANAME in a
CFMRMEP MO can
contain only ASCII
characters. The
name cannot be
null characters or
contain the
<, >, and \.
In the CFMRMEP
of MANAME and
MDNAME cannot
exceed 44 bytes.
RMEPID in the
CFMRMEP MO
must be unique in
the CFM MA.
MAC in the
CFMRMEP MO is
expressed in the
format of XXXX-
XXXX-XXXX. It
broadcast MAC
address (FFFF- Read Only N/A N/A N/A
FFFF-FFFF). It also
cannot be set to a
multicast MAC
address, which the
first bit in the
Destination
Adddress field is 1.

In a DBGSVR MO,
if SERVICETYPE is
set to TCP, this
parameter can be
set to any of the
following values:
22, 23, 80, 443,
1110, 1120, 2700,
4443, 6000, 6001,
6006, 6007 and
30023. Read Only N/A N/A N/A
In a DBGSVR MO,
if SERVICETYPE is
set to UDP, this
parameter can be
set to any of the
following values:
67, 68, 319, 320,
500, 3784, 4500,
4784, 17185,
33003, and 45300.
No (And no impact
mode)

In a DEVIP MO,
this parameter can
be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In a DEVIP MO,
this parameter can
be set to
BASE_BOARD or
ETH_COVERBOAR
7.
In a DEVIP MO,
this parameter can
be set to PPP,
MPGRP, ETH,
ETHTRK, or
LOOPINT if SBT is
set to
BASE_BOARD.
In a DEVIP MO,
this parameter can
be set to ETH,
ETHTRK, or
LOOPINT if SBT is
set to
ETH_COVERBOAR
D.
In a DEVIP MO,
this parameter can
be set to PPP,
MPGRP, or
LOOPINT if SBT is
set to
E1_COVERBOARD
.
BASE_BOARD and
PT is set to ETH.
In a DEVIP MO,
this parameter can
be set to 0 or 1 if
SBT is set to
BASE_BOARD and
PT is set to
ETHTRK.
In a DEVIP MO,
this parameter can
be set to 0 or 15 if
PT is set to PPP.
In a DEVIP MO,
this parameter can
be set to 0 or 3 if
PT is set to
MPGRP.
In a DEVIP MO,
this parameter can
be set to a value
within the range of
0 to 5 if SBT is set
to
ETH_COVERBOAR
D and PT is set to
ETH.
In a DEVIP MO,
this parameter can
be set to a value
within the range of
to
ETH_COVERBOAR
D and PT is set to
ETHTRK.
In a DEVIP MO,
this parameter can
MO.
If IKEIP in an
S1SERVIP MO is
same as IP in a
configured DEVIP
MO.
LOCIP in an
S1SIGIP MO must
be the same as IP
in a configured
DEVIP MO.
If LOCIKEIP in an
S1SIGIP MO is
same as IP in a
configured DEVIP
MO.
If SECLOCIKEIP in Read Only N/A N/A N/A
an S1SIGIP MO is
same as IP in a
configured DEVIP
MO.
If PT in the DEVIP
MO associated with
S1SERVIP in an
S1SERVIP MO is
set to LOOPINT,
and an SGW MO is
configured, the
eNodeB must be
configured with an
IP route that can
reach the SERVIP1
in the SGW MO or
with a DEVIP MO
In a DEVIP MO, if
PT is not set to
LOOPINT, MASK
cannot be set to all
1s.
In the binary value
into which MASK in
the DEVIP MO is
converted, 0 is not
No (And no impact
allowed to precede
1.
mode)
In the logical
operation result of
IP and MASK in a
DEVIP MO, neither
the network ID nor
host ID can be all
0s or 1s after being
converted into a
binary value.
If SIGIKEIP2 in an
S1SIGIP6 MO is
same as IPV6 in a
configured DEVIP6
MO.
If SERVIKEIP in an
X2SERVIP6 MO is
same as IPV6 in a
configured DEVIP6
MO.
SIGIP1 in an
X2SIGIP6 MO must
be the same as
IPV6 in a
configured DEVIP6
MO.
SIGIP2 in an Read Only N/A N/A N/A
X2SIGIP6 MO must
be the same as
IPV6 in a
configured DEVIP6
MO.
If SIGIKEIP1 in an
X2SIGIP6 MO is
same as IPV6 in a
configured DEVIP6
MO.
If PT in the IPITF6
MO associated with
SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
an SGW6 MO is
configured, the
In a DEVIP6 MO, if
IPV6 is set to the
local address of a
link, PFXLEN must
be greater than or
equal to 10.

No (And no impact
mode)
DHCPSVRIP in a
DHCPSVRIP MO
must be a valid IP
address of class A, Read Only N/A N/A N/A
it cannot be 0.x.x.x
or 127.x.x.x.
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

the value range of
this parameter is
from 0 to 63 if
PRIRULE is set to Services are
DSCP. interrupted until the
Read & Write Yes BS
In the DIFPRI MO, parameter is
the value range of correctly set.
this parameter is
from 0 to 7 if
PRIRULE is set to
IPPRECEDENCE.
In a DIFPRI MO,
OMLOWPRI must
be smaller than or
equal to
OMHIGHPRI.
In the DIFPRI MO,
if PRIRULE is set to
Services are
DSCP, the value
range of this Read & Write Yes BS
parameter is
parameter is from 0
correctly set.
to 63.
In the DIFPRI MO,
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
In a DIFPRI MO,
OMLOWPRI must
be smaller than or
equal to
OMHIGHPRI.
In the DIFPRI MO,
Services are
DSCP, the value
range of this Read & Write Yes BS
parameter is
parameter is from 0
correctly set.
to 63.
In the DIFPRI MO,
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
In the DIFPRI MO,

DSCP, the value
range of this
parameter is from 0 Services are
to 63. interrupted until the
Read & Write Yes BS
if PRIRULE is set to correctly set.
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the DIFPRI MO,

DSCP, the value
range of this
Read & Write Yes BS
IPPRECEDENCE,
the value range of
this parameter is
from 0 to 7.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

In the DOT1X MO,
if SBT is set to
BASE_BOARD, this
parameter can be
set to 0 or 1.
In the DOT1X MO, Read Only N/A N/A N/A
if SBT is set to
ETH_COVERBOAR
D, the value range
from 0 to 5.
In a DOT1X MO,
No (And no impact
AM must be set to
EAP-TLS if ACT is
mode)
set to ACTIVE.

No (And no impact
mode)

In the E1T1 MO,

this parameter is
valid only when PS Read Only N/A N/A N/A
is set to
SINGLEPORT.
No (And no impact
mode)
In the E1T1 MO,

this parameter is
valid only when PS
is set to ALLPORT.
FRAME.
In an E1T1 MO, if
PS and
WORKMODE are
set to ALLPORT
and T1,
respectively,
FRAME can be set
to
T1_SUPER_FRAM
E or
T1_EXTENDED_S
UPER_FRAME.
If WORKMODE in
an all-port E1T1
MO is set to
E1_UNBA or
E1_BA, FRAME
can be set to
E1_DOUBLE_FRA
ME or
E1_CRC4_MULTI_
FRAME in each
single-port E1T1
MO. If
WORKMODE in an
all-port E1T1 MO is
set to T1, FRAME
can be set to
T1_SUPER_FRAM
E or
T1_EXTENDED_S
UPER_FRAME in
each single-port
E1T1 MO. If no all-
port E1T1 MO is
configured, the
default value of
ALLPORT and
WORKMODE is set
to E1_UNBA or
E1_BA, LNCODE
can be set to AMI or
HDB3.
In an E1T1 MO, if
PS and
WORKMODE are
set to ALLPORT
and T1,
respectively,
LNCODE can be
set to AMI or B8ZS.
If WORKMODE in
an all-port E1T1
MO is set to
E1_UNBA or
E1_BA, LNCODE Read & Write Yes BS Less than 1 minute
HDB3 in each
single-port E1T1
MO. If
WORKMODE in an
all-port E1T1 MO is
set to T1, LNCODE
B8ZS in each
single-port E1T1
MO. If no all-port
E1T1 MO is
configured, the
default value of
WORKMODE in
each single-port
E1T1 MO is
E1_UNBA, and
When adding an
E1T1 MO, this
parameter can be
set to
E1_COVERBOARD
if SN is set to a
value within the
range of 0 to 5.
When adding an
E1T1 MO, this
parameter can be
set to
BASE_BOARD if
SN is set to 6 or 7.
No (And no impact
mode)

In an ETHOAM3AH
MO, this parameter
must be set to
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In an ETHOAM3AH
MO, this parameter
can be set to
BASE_BOARD or
ETH_COVERBOAR
7.
In the
ETHOAM3AH MO,
this parameter can
be set to 0 or 1 if
SBT is set to
BASE_BOARD.
In the
ETHOAM3AH MO, Read Only N/A N/A N/A
this parameter can
be set to a value
within the range of
to
ETH_COVERBOAR
D.


In an ETHOAM3AH
MO,
ERRFRMSCDEVT
PRD must be
greater than or
equal to
ERRFRMSCDEVTT
HD.
In an ETHOAM3AH
MO,
ERRFRMSCDEVT
PRD must be
greater than or
equal to
ERRFRMSCDEVTT
HD.


In the ETHPORT
MO, if SN is within
the range from 0 to
5, this parameter
must be set to
ETH_COVERBOAR
D.
In the ETHPORT
MO, if SN is set to 6
or 7, this parameter
can be set to
BASE_BOARD or
ETH_COVERBOAR
D.
In the ETHPORT
MO, this parameter
can be set to 0 or 1
if SBT is set to
BASE_BOARD.
In the ETHPORT
MO, this parameter Read Only N/A N/A N/A
can be set to a
value within the
range of 0 to 5 if
SBT is set to
ETH_COVERBOAR
D.
In the ETHPORT
MO, if SBT is set to
BASE_BOARD, this
parameter can be
set to COPPER,
FIBER or AUTO. Less than 10
Read & Write Yes BS
In the ETHPORT minutes
MO, if SBT is set to
ETH_COVERBOAR
D, this parameter
can be set to
COPPER or FIBER.
Services are
parameter is
correctly set.
ETH_COVERBOAR
D and COPPER,
respectively, this
parameter can be
set to 10M, 100M,
1000M, or AUTO.
In the ETHPORT
MO, if SBT and PA
are set to
ETH_COVERBOAR
D and FIBER,
respectively, this
parameter can be
set to 100M,
1000M, or AUTO.
In the ETHPORT
MO, if SBT and PA
are set to
All the services
BASE_BOARD and Read & Write Yes Less than 1 minute
carried on the port
COPPER,
respectively, this
parameter can be
set to 10M, 100M,
or AUTO.
In the ETHPORT
MO, if SBT and PA
are set to
BASE_BOARD and
FIBER,
respectively, this
parameter can be
set to 100M,
1000M, or AUTO.
In the ETHPORT
MO, if SBT and PA
are set to
BASE_BOARD and
In the ETHPORT
MO, if SPEED is set
to AUTO, this
parameter must be
AUTO.
All the services
In the ETHPORT Read & Write Yes Less than 1 minute
carried on the port
MO, if SPEED is set
to 10M, 100M, or
1000M, this
parameter must be
FULL.
Services are
parameter is
correctly set.
No (And no impact
mode)
In an ETHPORT
No (And no impact
MO, FERAT must
be greater than or
mode)
equal to FERDT.
In an ETHPORT
No (And no impact
MO, FERAT must
be greater than or
mode)
equal to FERDT.



All services over the

None Read & Write Yes member ports of Less than 1 minute
the Ethernet trunk
No (And no impact
mode)
In an ETHTRK MO,
this parameter must
be set to
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In an ETHTRK MO,
this parameter can
be set to
BASE_BOARD or
ETH_COVERBOAR
7.
All services carried
None Read & Write Yes on the members of Less than 1 minute
the Ethernet trunk



In an ETHTRKLNK
MO, this parameter
can be set to a
value within the
range of 0 to 5 if
SBT is set to
ETH_COVERBOAR Read Only N/A N/A N/A
D.
In an ETHTRKLNK
MO, this parameter
if SBT is set to
BASE_BOARD.
In an ETHTRKLNK
MO, this parameter
must be set to
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In an ETHTRKLNK
MO, this parameter
can be set to
BASE_BOARD or
ETH_COVERBOAR
7.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the
FLOODDEFEND
MO, this parameter
is valid only when
DFDSW is set to
ENABLE.
In the
FLOODDEFEND
MO, if FLDTYPE is
set to ARP,
DFDTHD ranges
from 1 to 512. No (And no impact
FLOODDEFEND mode)
MO, if FLDTYPE is
set to ICMP or
SYN, DFDTHD
ranges from 1 to
1024.
In the
FLOODDEFEND
MO, if FLDTYPE is
set to TCP or UDP,
DFDTHD ranges
from 1 to 4096.
No (And no impact
mode)
In the
FLOODDEFEND
MO, this parameter
is valid only when
ALMSW is set to
ENABLE.
In the
FLOODDEFEND
MO, if FLDTYPE is
set to ARP,
ALMTHD ranges
from 1 to 512. No (And no impact
FLOODDEFEND mode)
MO, if FLDTYPE is
set to ICMP or
SYN, ALMTHD
ranges from 1 to
1024.
In the
FLOODDEFEND
MO, if FLDTYPE is
set to TCP or UDP,
ALMTHD ranges
from 1 to 4096.

No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
Services are
parameter is
correctly set.

PEERNAME in a
configured
IKEPEER MO.
If IKEPEERNM in
an X2SERVIP MO
the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP1IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP1IKEPEER
NM in this MO must
be the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP2IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP2IKEPEER
NM in this MO must
be the same as
PEERNAME in a
configured
IKEPEER MO.
If
SERVIP3IPSECFL
AG in an SGW MO
is set to ENABLE,
SERVIP3IKEPEER
NM in this MO must
be the same as
PEERNAME in a
If AUTHALG in an
IKEPROPOSAL
MO is set to
AES_XCBC_96,
IKEVERSION in the Read & Write Yes BS Less than 1 minute
associated
IKEPEER MO
cannot be set to
IKE_V1.
In the IKEPEER
MO, this parameter
is valid only when Read & Write Yes BS Less than 1 minute
IKEVERSION is set
to IKE_V1.
REMOTEIP in an
IKEPEER MO must
be a valid IP
address of class A, Read & Write Yes BS Less than 1 minute
it cannot be set to
0.x.x.x or 127.x.x.x.

In the IKEPEER
MO, this parameter
DPD is set to
PERIODIC.
In the IKEPEER
MO, this parameter
DPD is set to
PERIODIC.
In the IKEPEER
MO, this parameter
DPD is set to
PERIODIC.

configured
IKEPEER6 MO.
If IKEPEERNM2 in
an X2SIGIP6 MO is
same as
PEERNAME in a
configured
IKEPEER6 MO.
If IKEPEERNM in
an X2SERVIP6 MO
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If
SERVIP1IPSECFL
AG in an SGW6 Read Only N/A N/A N/A
MO is set to
ENABLE,
IKEPEERNM1 in
this MO must be
the same as
PEERNAME in a
configured
IKEPEER6 MO.
If
SERVIP2IPSECFL
AG in an SGW6
MO is set to
ENABLE,
IKEPEERNM2 in
this MO must be
the same as
PEERNAME in a
configured
No (And no impact
mode)
If AUTHALG in an
IKEPROPOSAL
MO is set to
associated mode)
IKEPEER6 MO
cannot be set to
IKE_V1.
In an IKEPEER6
IKEVERSION is set mode)
to IKE_V1.
No (And no impact
mode)
In an IKEPEER6
MO, REMOTEIP No (And no impact
must be set to a Read & Write on the UE in idle N/A N/A
global unicast mode)
address.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an IKEPEER6
DPD is set to mode)
PERIODIC.
In an IKEPEER6
DPD is set to mode)
PERIODIC.
In an IKEPEER6
DPD is set to mode)
PERIODIC.
In an IKEPEER6
MO, LOCALIP No (And no impact
must be set to a Read & Write on the UE in idle N/A N/A
global unicast mode)
address.

PROPID in an
SONSECPARA MO
must be the same
as PROPID in a
configured
IKEPROPOSAL
MO.
If AUTHMETH in
the IKEPROPOSAL
MO associated with
an SONSECPARA
MO is set to
PRE_SHARED_KE
Y, PKEY in the
SONSECPARA MO
cannot be empty.
No (And no impact
mode)
If AUTHALG in an
IKEPROPOSAL
MO is set to
associated mode)
SONSECPARA MO
cannot be set to
IKE_V1.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

DSTIP in an
IP2RSCGRP MO
must be a valid IP
address of class A,
it cannot be set to
0.x.x.x or 127.x.x.x.
In an IP2RSCGRP
MO, the logic AND
result of DSTIP and
DSTMASK must be
the same as
DSTIP. That is,
DSTIP must be set
to a network IP
address.
In an IP2RSCGRP
MO, the logic AND
result of DSTIP and
DSTMASK must be
the same as
DSTIP. That is,
DSTIP must be set
to a network IP
address. Read Only N/A N/A N/A
In the binary value
into which
DSTMASK in an
IP2RSCGRP MO is
converted, 0 cannot
precede 1, but the
value can be
255.255.255.255.
In an IP2RSCGRP
MO, this parameter
can be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5. Read Only N/A N/A N/A
In an IP2RSCGRP
MO, this parameter
can be set to
BASE_BOARD,
BACK_BOARD or
ETH_COVERBOAR
7.
In an IP2RSCGRP
MO, this parameter
can be set to PPP
or MPGRP if SBT is
set to
E1_COVERBOARD
.
In an IP2RSCGRP
MO, this parameter
can be set to ETH
or ETHTRK if SBT
is set to
ETH_COVERBOAR
D. Read Only N/A N/A N/A
In an IP2RSCGRP
MO, this parameter
can be set to PPP,
MPGRP, ETH, or
ETHTRK if SBT is
set to
BASE_BOARD.
In an IP2RSCGRP
MO, this parameter
must be set to
TUNNEL if SBT is
set to
BACK_BOARD.
range of 0 to 15 if
PT is set to PPP.
In an IP2RSCGRP
MO, this parameter
can be set to a
value within the
range of 0 to 3 if PT
is set to MPGRP.
In an IP2RSCGRP
MO, this parameter
can be set to a
value within the
range of 0 to 5 if
SBT is set to
ETH_COVERBOAR
D and PT is set to
ETH.
In an IP2RSCGRP
MO, this parameter
can be set to a
value within the
range of 0 to 2 if
SBT is set to
ETH_COVERBOAR
D and PT is set to
ETHTRK.
In an IP2RSCGRP
MO, this parameter
if SBT is set to
BASE_BOARD and
PT is set to ETH or
ETHTRK.
In an IP2RSCGRP
MO, this parameter
can be set to a
value within the
range of 0 to 14 if
No (And no impact
mode)
This parameter is
ARPSPOOFCHKS Read & Write on the UE in idle N/A N/A
W is set to mode)
ENABLE.
No (And no impact
mode)
No (And no impact
mode)
This parameter is
INVALIDPKTCHKS Read & Write on the UE in idle N/A N/A
W is set to mode)
ENABLE.
No (And no impact
mode)
This parameter is
IPSECREPLAYCH Read & Write on the UE in idle N/A N/A
KSW is set to mode)
ENABLE.

If PT in an IPITF6
MO is set to
LOOPIF, the Read Only N/A N/A N/A
ITFTYPE cannot be
set to VLAN.
In the IPITF6 MO, if

SN is set to 6 or 7,
this parameter can Read Only N/A N/A N/A
be set to
BASE_BOARD.
If PT in an IPITF6
MO is set to
LOOPIF, the Read Only N/A N/A N/A
ITFTYPE cannot be
set to VLAN.
In the IPITF6 MO,
this parameter can
be set to 0 or 1 if
PT is set to ETH or
TRUNK and SBT is
set to
BASE_BOARD.
In the IPITF6 MO, Read Only N/A N/A N/A
this parameter can
be set to a value
within the range of
0 to 2 if PT is set to
LOOPIF and SBT is
set to
BASE_BOARD.
In the IPITF6 MO,

this parameter is
ITFTYPE is set to
VLAN.


In an IPPATH MO,
if LOCALIP is set to
0.0.0.0, PT must be
set to PPP or
MPGRP.
In an IPPATH MO,
this parameter can
be set to PPP,
MPGRP, ETH, or
ETHTRK if SBT is
set to
BASE_BOARD.
In an IPPATH MO,
this parameter can
be set to PPP or
MPGRP if SBT is Read & Write Yes BS Less than 1 minute
set to
E1_COVERBOARD
.
In an IPPATH MO,
this parameter can
be set to ETH or
ETHTRK if SBT is
set to
ETH_COVERBOAR
D.
In an IPPATH MO,
this parameter must
be set to TUNNEL if
SBT is set to
BACK_BOARD.
0 to 15 if PT is set
to PPP.
In an IPPATH MO,
this parameter can
be set to a value
within the range of
0 to 3 if PT is set to
MPGRP.
In an IPPATH MO,
this parameter can
be set to a value
within the range of
to
ETH_COVERBOAR
D and PT is set to
ETH.
In an IPPATH MO,
this parameter can Read & Write Yes BS Less than 1 minute
be set to a value
within the range of
to
ETH_COVERBOAR
D and PT is set to
ETHTRK.
In an IPPATH MO,
this parameter can
be set to 0 or 1 if
SBT is set to
BASE_BOARD and
PT is set to ETH or
ETHTRK.
In an IPPATH MO,
this parameter can
be set to a value
within the range of
No (And no impact
mode)
In the IPPATH MO,

Services are
this parameter is
valid only when Read & Write Yes BS
parameter is
PATHTYPE is set to
correctly set.
QOS.
LOCALIP in an
IPPATH MO must
be an IP address of
class A, B, or C. In
addition, it cannot
be set to 127.x.x.x
or 0.x.x.x (including
0.0.0.0).
In an IPPATH MO, Read & Write Yes BS Less than 1 minute
LOCALIP must be
different from
PEERIP.
In an IPPATH MO,
if LOCALIP is set to
0.0.0.0, PT must be
set to PPP or
MPGRP.
PEERIP in an
IPPATH MO must
be an IP address of
addition, it cannot
be set to 127.x.x.x Read & Write Yes BS Less than 1 minute
or 0.x.x.x.
In an IPPATH MO,
LOCALIP must be
different from
PEERIP.

No (And no impact
mode)
Service are
Interface S1 and interrupted until the
services in the cell path check is
disabled.

In the IPPATH MO,

this parameter is
valid only when Read & Write Yes BS Less than 1 minute
JNRSCGRP is set
to ENABLE.
No (And no impact
mode)
In an IPPATH MO,
this parameter can
be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In an IPPATH MO,
this parameter can
be set to
BASE_BOARD or
ETH_COVERBOAR
7.

In an IPPATH6 MO,
LOCALIP6 must be
set to a global
unicast address.
In an IPPATH6 MO,
LOCALIP6 and
PEERIP6 cannot be
the same.
In an IPPATH6 MO,
PEERIP6 must be
set to a global
unicast address.
In an IPPATH6 MO,
LOCALIP6 and
PEERIP6 cannot be
the same.

No (And no impact
mode)
No (And no impact
mode)
SRCIP in an
IPPATHRT MO
must be a valid IP
address of class A,
it cannot be set to Read Only N/A N/A N/A
0.x.x.x or 127.x.x.x.
In an IPPATHRT
MO, SRCIP must
be different from
DSTIP.
DSTIP in an
IPPATHRT MO
must be a valid IP
address of class A,
it cannot be set to Read Only N/A N/A N/A
0.x.x.x or 127.x.x.x.
In an IPPATHRT
MO, SRCIP must
be different from
DSTIP.
NEXTHOPIP in an
IPPATHRT MO
must be a valid IP
it cannot be set to
0.x.x.x or 127.x.x.x.
In an
IPPMSESSION
MO, if BINDPATH is
set to NO,
LOCALIP must be
a valid IP address
of class A, B, or C.
In addition, it
cannot be set to Read Only N/A N/A N/A
0.x.x.x or 127.x.x.x.
In an
IPPMSESSION
MO, if BINDPATH is
set to NO,
LOCALIP must be
different from
PEERIP.
In an
IPPMSESSION
MO, if BINDPATH is
set to NO, PEERIP
must be a valid IP
address of class A,
it cannot be set to
0.x.x.x or 127.x.x.x Read Only N/A N/A N/A
In an
IPPMSESSION
MO, if BINDPATH is
set to NO,
LOCALIP must be
different from
PEERIP.
In the
IPPMSESSION
MO, this parameter
is valid only when
BINDPATH is set to
NO.
This parameter is
valid only when
IppmUpActState in Read Only N/A N/A N/A
an IPPMSESSION
MO is set to PMUP.
This parameter is
valid only when
IppmDownActStat
e in an
IPPMSESSION MO
is set to PMUP.
This parameter is
valid only when
IppmDownActStat
e in an
IPPMSESSION MO
is set to PMUP.
This parameter is
valid only when
IppmDownActStat
e in an
IPPMSESSION MO
is set to PMUP.
This parameter is
valid only when
IppmUpActState in Read Only N/A N/A N/A
an IPPMSESSION
MO is set to PMUP.

In the
IPPMSESSION
MO, this parameter
is valid only when
BINDPATH is set to
YES.

In an IPRT MO, this

parameter can be
set to
BACK_BOARD,
E1_COVERBOARD
, or
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In an IPRT MO, this
parameter can be
set to
BASE_BOARD,
BACK_BOARD, or
ETH_COVERBOAR
7.
In an IPRT MO, this
parameter can be
set to PPP or
MPGRP if SBT is
set to
BASE_BOARD or
E1_COVERBOARD
and RTTYPE is set
to IF.
In an IPRT MO, this
parameter must be
set to TUNNEL if
SBT is set to
BACK_BOARD and
RTTYPE is set to
IF.
In an IPRT MO, this

parameter can be
set to a value within
the range of 0 to 15
if RTTYPE is set to
IF and IFT is set to
PPP.
In an IPRT MO, this
parameter can be
the range of 0 to 3 if Read Only N/A N/A N/A
RTTYPE is set to IF
and IFT is set to
MPGRP.
In an IPRT MO, this
parameter can be
if RTTYPE is set to
IF and IFT is set to
TUNNEL.
In an IPRT MO, this
parameter must be
set to NEXTHOP if
SBT is set to
ETH_COVERBOAR
D.
In an IPRT MO, this
parameter must be
set to IF if SBT is
set to
E1_COVERBOARD
.
In an IPRT MO, this
parameter can be
set to NEXTHOP or
IF if SBT is set to
BASE_BOARD.
In an IPRT MO, this
parameter must be
set to If if SBT is
set to
BACK_BOARD.
If PT in the DEVIP
MO associated with
S1SERVIP in an
S1SERVIP MO is
set to LOOPINT,
and SERVIP4 in an
SGW MO is not
0.0.0.0, the eNodeB
must be configured
can reach this
SERVIP4 or with a
DEVIP MO that is
on the same
network segment
as this SERVIP4
and has PT set to a
value other than
LOOPINT.
If PT in the DEVIP
MO associated with
X2SERVIP in an
X2SERVIP MO is
set to LOOPINT,
and SERVIP1 in an
X2ENODEB MO is
not 0.0.0.0, the
local eNodeB must
be configured with
reach this SERVIP1
or with a DEVIP MO
that is on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPINT.
In the binary value
converted from
DSTMASK in an
IPRT MO, 0 is not
allowed to precede
1. DSTMASK can
be set to 0.0.0.0 or
255.255.255.255.
If one of DSTMASK
and DSTIP in an
IPRT MO is set to Read Only N/A N/A N/A
0.0.0.0, the other
must be set to
0.0.0.0, too.
The result of DSTIP
AND DSTMASK in
an IPRT MO must
be equal to DSTIP.
That is, DSTIP must
be set to a network
IP address.
NEXTHOP in an
IPRT MO must be a
valid IP address of
addition, it cannot
be set to 127.x.x.x,
0.x.x.x, or Read Only N/A N/A N/A
255.255.255.255.
In the IPRT MO,
this parameter is
valid only when
RTTYPE is set to
NEXTHOP.

No (And no impact
mode)

SERVIP in an
S1SERVIP6 MO is
set to LOOPIF, and
SERVIP4 in an
SGW6 MO is not
0:0:0:0:0:0:0:0, the
eNodeB must be
configured with an
IPv6 route that can
reach this SERVIP4
or with a DEVIP6
MO that is on the
same network
segment as this
SERVIP4 and has
PT set to a value
other than LOOPIF.
If PT in the IPITF6
MO associated with
SERVIP in an
X2SERVIP6 MO is
set to LOOPIF, and
SERVIP1 in an
X2ENODEB6 MO is
not 0:0:0:0:0:0:0:0,
the local eNodeB
must be configured
with an IPv6 route
that can reach this
SERVIP1 or with a
DEVIP6 MO that is
on the same
network segment
as this SERVIP1
and has PT set to a
value other than
LOOPIF.
If PT in the IPITF6
In an IPRT6 MO,
DSTIP and
PFXLEN must be Read Only N/A N/A N/A
both 0 or a value
other than 0.

In an IPRT6 MO,
NEXTHOPIP must
match Read Only N/A N/A N/A
NEXTHOPIP6TYPE
.

No (And no impact
mode)

In the IPSECBIND
MO, if SN is within
the range from 0 to
5, this parameter
must be set to
ETH_COVERBOAR
D.
In the IPSECBIND
MO, if SN is set to 6
or 7, this parameter
can be set to
BASE_BOARD or
ETH_COVERBOAR
D.
In the IPSECBIND
MO, this parameter
SBT is set to
BASE_BOARD.
In an IPSECBIND
MO, this parameter
if SBT is set to
BASE_BOARD and
PT is set to ETH or
ETHTRK.
In an IPSECBIND
MO, this parameter
can be set to a
value within the
range of 0 to 5 if
SBT is set to Read Only N/A N/A N/A
ETH_COVERBOAR
D and PT is set to
ETH.
In an IPSECBIND
MO, this parameter
can be set to a
value within the
range of 0 to 2 if
SBT is set to
ETH_COVERBOAR
D and PT is set to
ETHTRK.

In an IPSECDTNL
MO, the
combination of
No (And no impact
MSPGN and
MSPSN must be
mode)
SSPGN and
SSPSN.
In an IPSECDTNL
MO, the
combination of
No (And no impact
MSPGN and
MSPSN must be
mode)
SSPGN and
SSPSN.
In an IPSECDTNL
MO, the
combination of
No (And no impact
MSPGN and
MSPSN must be
mode)
SSPGN and
SSPSN.
In an IPSECDTNL
MO, the
combination of
No (And no impact
MSPGN and
MSPSN must be
mode)
SSPGN and
SSPSN.
No (And no impact
mode)
No (And no impact
mode)
SPGN in an
IPSECPOLICY MO Read Only N/A N/A N/A
is case insensitive.


In the
IPSECPOLICY MO,
this parameter is
valid only when
LTCFG is set to
LOCAL.
In the
IPSECPOLICY MO,
this parameter is
valid only when
LTCFG is set to
LOCAL.

No (And no impact
mode)
SPGN in an
IPSECPOLICY6
MO is case
insensitive.
No (And no impact
mode)
In an
IPSECPOLICY6
No (And no impact
MO, this parameter
is valid only when
mode)
ACLTYPE is set to
IPV4.
In an
IPSECPOLICY6
No (And no impact
MO, this parameter
is valid only when
mode)
ACLTYPE is set to
IPV6.
No (And no impact
mode)

No (And no impact
mode)
No (And no impact
mode)
In an
IPSECPOLICY6
No (And no impact
MO, this parameter
is valid only when
mode)
LTCFG is set to
LOCAL.
In an
IPSECPOLICY6
No (And no impact
MO, this parameter
is valid only when
mode)
LTCFG is set to
LOCAL.

be the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
If IPSECPROPNM
in an X2SERVIP
be the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
PROPNAME in an
SONSECPARA MO
must be the same
as PROPNAME in
a configured Read Only N/A N/A N/A
IPSECPROPOSAL
MO.
If SIGIP1SECFLAG
in an MME6 MO is
set to ENABLE,
IPSECPROPNM1
in this MO must be
the same as
PROPNAME in a
configured
IPSECPROPOSAL
MO.
If SIGIP2SECFLAG
in an MME6 MO is
set to ENABLE,
IPSECPROPNM2
in this MO must be
the same as
No (And no impact
mode)
In the
IPSECPROPOSAL
MO, TRANMODE is
set to ESP or No (And no impact
AH_ESP, Read & Write on the UE in idle N/A N/A
ESPAUTHALG and mode)
ESPENCALG
cannot be both set
to NULL.
In the
IPSECPROPOSAL
No (And no impact
MO, this parameter
is valid only when
mode)
TRANMODE is set
to AH or AH_ESP.
In an
IPSECPROPOSAL
MO, if TRANMODE
is set to ESP or
AH_ESP,
ESPAUTHALG and
ESPENCALG No (And no impact
cannot be both set Read & Write on the UE in idle N/A N/A
to NULL. mode)
In the
IPSECPROPOSAL
MO, this parameter
is valid only when
TRANMODE is set
to ESP or AH_ESP.
In an
IPSECPROPOSAL
MO, if TRANMODE
is set to ESP or
AH_ESP,
ESPAUTHALG and
ESPENCALG No (And no impact
cannot be both set Read & Write on the UE in idle N/A N/A
to NULL. mode)
In the
IPSECPROPOSAL
MO, this parameter
is valid only when
TRANMODE is set
to ESP or AH_ESP.

IP in the LOCALIP
MO must be set to
a valid IP address
of Class A, B, or C.
In addition, it
cannot be 127.x.x.x
No (And no impact
or 0.x.x.x.
In a LOCALIP MO,
mode)
neither the network
ID nor the host ID
can be all 0s or 1s
in the logical
operation result of
IP and MASK.
In the binary value

converted from
MASK in the
LOCALIP MO, 0 is
not allowed to
precede 1. MASK
cannot be 0.0.0.0 or No (And no impact
255.255.255.255. Read & Write on the UE in idle N/A N/A
In a LOCALIP MO, mode)
neither the network
ID nor the host ID
can be all 0s or 1s
in the logical
operation result of
IP and MASK.
In a LOCALIP6
MO, IP6 must be a
link-local address
No (And no impact
whose prefix is
greater than or
mode)
equal to 10, or be a
global unicast
address.
In a LOCALIP6
MO, if IP6 is set to
No (And no impact
the local address of
a link, PFXLEN
mode)
must be greater
than or equal to 10.

In the LR MO, if
SBT is set to
E1_COVERBOARD
, this parameter
must be set to
MPGRP.
In the LR MO, if
SBT is set to
ETH_COVERBOAR
D, this parameter
can be set to ETH
or ETHTRK. Read Only N/A N/A N/A
In the LR MO, if
SBT is set to
BASE_BOARD, this
parameter can be
set to MPGRP, ETH
or ETHTRK.
In the LR MO, if
SBT is set to
BACK_BOARD, this
parameter must be
set to TUNNEL.
In the LR MO, this
parameter can be
the range of 0 to 3 if
PT is set to
MPGRP.
In an LR MO, this
parameter can be
if PT is set to
TUNNEL.
In the LR MO, this
parameter can be
PT is set to ETH
and SBT is set to
ETH_COVERBOAR
D.
In the LR MO, this
parameter can be
PT is set to
ETHTRK and SBT
is set to
ETH_COVERBOAR
D.
In the LR MO, this
parameter can be
set to 0 or 1 if PT is
set to ETH or
ETHTRK and SBT
is set to
BASE_BOARD.
No (And no impact
mode)
In the LR MO, this
parameter can be
the range of 32 to
31744 if PT is set to
MPGRP.
In the LR MO, this
parameter can be
the range of 32 to
360000 if PT is set
to TUNNEL.
In the LR MO, this
parameter can be No (And no impact
set to a value within Read & Write on the UE in idle N/A N/A
the range of 32 to mode)
1000000 if PT is set
to ETH or ETHTRK
and SBT is set to
ETH_COVERBOAR
D.
In the LR MO, this
parameter can be
the range of 32 to
360000 if PT is set
to ETH or ETHTRK
and SBT is set to
BASE_BOARD.
In the LR MO, this
parameter can be
the range of 32 to
155000 if PT is set
to MPGRP.
In the LR MO, this
parameter can be
the range of 32 to
300000 if PT is set
to TUNNEL.
In the LR MO, this
to ETH or ETHTRK
and SBT is set to
ETH_COVERBOAR
D.
In the LR MO, this
parameter can be
the range of 32 to
300000 if PT is set
to ETH or ETHTRK
and SBT is set to
BASE_BOARD.
In the LR MO, this
parameter can be
the range of 0 to
155000 if PT is set
to MPGRP.
In the LR MO, this
parameter can be
the range of 0 to
300000 if PT is set
to TUNNEL.
In the LR MO, this
to ETH or ETHTRK
and SBT is set to
ETH_COVERBOAR
D.
In the LR MO, this
parameter can be
the range of 0 to
300000 if PT is set
to ETH or ETHTRK
and SBT is set to
BASE_BOARD.
In an LR MO, this
parameter can be
set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SN is set to a
value within the
In an LR MO, this
parameter can be
set to
BASE_BOARD,
BACK_BOARD, or
ETH_COVERBOAR
7.
In the LR MO, this
parameter can be
the range of 32 to
31744 if PT is set to
MPGRP.
In the LR MO, this
parameter can be
the range of 32 to
540000 if PT is set
to TUNNEL.
In the LR MO, this
to ETH or ETHTRK
and SBT is set to
ETH_COVERBOAR
D.
In the LR MO, this
parameter can be
the range of 32 to
540000 if PT is set
to ETH or ETHTRK
and SBT is set to
BASE_BOARD.
In the MPGRP MO,

this parameter can
be set to a value
within the range of
to BASE_BOARD.
In the MPGRP MO,

this parameter is
AUTH is set to PAP
or CHAP.
In the MPGRP MO,
this parameter is
AUTH is set to PAP
or CHAP.
LOCALIP in an
MPGRP MO must
be a valid IP
address of class A,
it cannot be set to
the reserved IP
addresses 0.x.x.x
or 127.x.x.x but can
be set to 0.0.0.0.
In the MPGRP MO,
IPMASK cannot be
all 0s if LOCALIP is
not all 0s.
In an MPGRP MO,
neither the network
ID nor the host ID
can be all 0s or 1s
in the logical
operation result of
LOCALIP and
IPMASK.
In an MPGRP MO,
LOCALIP must be
different from
PEERIP.
In the MPGRP MO,
IPMASK must be
all 0s.
IPMASK in the
MPGRP MO must
be valid, that is, 0 is
not allowed to
precede 1. In
addition, it can be
set to 0.0.0.0 or
255.255.255.255.
In the MPGRP MO,
IPMASK cannot be
not all 0s.
In an MPGRP MO,
neither the network
ID nor the host ID
can be all 0s or 1s
in the logical
operation result of
LOCALIP and
IPMASK.
In an MPGRP MO,
LOCALIP must be
different from
PEERIP.
In the MPGRP MO,
IPMASK must be
all 0s.
PEERIP in an
MPGRP MO must
be a valid IP
address of class A,
it cannot be set to
the reserved IP
addresses 0.x.x.x
be set to 0.0.0.0.
In the MPGRP MO,

this parameter is
MCPPP is set to
ENABLE.

In the MPGRP MO,

MAXMFLEN must
be larger than
MAXSFLEN and
the minimum
difference is 2. Read Only N/A N/A N/A
In the MPGRP MO,
this parameter is
valid only when
MUXCP is set to
ENABLE.
In the MPGRP MO,

MAXMFLEN must
be larger than
MAXSFLEN and
the minimum
In the MPGRP MO,
this parameter is
valid only when
MUXCP is set to
ENABLE.
In the MPGRP MO,
this parameter is
MUXCP is set to
ENABLE.
In the MPGRP MO,

if MCPPP is set to
ENABLE and MHO
is set to LONG, this
parameter can be
set to 4 or 8.
In the MPGRP MO,
if MCPPP is set to
ENABLE and MHO
is set to SHORT,
this parameter must
be set to 4.
In the MPGRP MO,

MPDAAT must be
greater than or
equal to MPDADT.
In the MPGRP MO,

MPDAAT must be
greater than or
equal to MPDADT.


In the MPGRP MO,

if the value of SN is
within the range
from 0 to 5, this
parameter must be
set to
E1_COVERBOARD Read Only N/A N/A N/A
.
In the MPGRP MO,
if SN is set to 6 or
7, this parameter
must be set to
BASE_BOARD.

In an MPLNK MO,
SRN must be the Read Only N/A N/A N/A
same as E1T1SRN.
In the MPLNK MO,

this parameter is
valid only when SN Read Only N/A N/A N/A
and SBT are both
set to valid values.
In the MPLNK MO,
this parameter is
and SBT are both
In an MPLNK MO,
SRN must be the Read Only N/A N/A N/A
same as E1T1SRN.
In the MPLNK MO,

this parameter is
and SBT are both
In the MPLNK MO,

this parameter is
valid only when SN,
SBT, E1T1SN, and
E1T1SBT are all
In the E1T1 MO, if
WORKMODE is set
to E1_BA or
E1_UNBA, TSN
must be set to a
value other than
TS0; if
WORKMODE is set
to T1, TSN must be
the range of TS1 to
TS24, Other
timeslots are not
used.

In an MPLNK MO,
if E1T1SN is the
same as SN,
E1T1SBT must be
the same as SBT.
In the MPLNK MO,
this parameter must
be set to
E1_COVERBOARD
within the range of
0 to 5.
In the MPLNK MO,
this parameter must
be set to
BASE_BOARD if
the value of SN is 6
or 7.
In the MPLNK MO,

this parameter is
and SBT are both

In an MPLNK MO,
if E1T1SN is the
same as SN,
E1T1SBT must be
the same as SBT.
In the MPLNK MO, Read Only N/A N/A N/A
this parameter is
valid only when SN,
SBT, E1T1SN are
all set to valid
values.

IP in the OMCH MO
must be a valid IP
address of Class A,
B, or C, and cannot
be set to 127.X.X.X
or 0.X.X.X.
In an OMCH MO, if
MASK is set to a
value other than
255.255.255.255,
neither the network
ID nor the host ID
can be all 0s or all
No (And no impact
1s in the logical
operation result of
mode)
IP and MASK.
In an OMCH MO, IP
must be different
from PEERIP.
In an OMCH MO,
NEXTHOP must be
different from IP.
In an OMCH MO, if
BEAR and BRT are
set to IPV4 and
YES, respectively,
DSTIP must be
different from IP.
MASK in an OMCH
MO must be set to
a valid mask (0 is
not allowed to
precede 1). In an
OMCH MO, this
parameter can be
set to
255.255.255.255
when BEAR is set No (And no impact
to IPV4. Read & Write on the UE in idle N/A N/A
In an OMCH MO, if mode)
MASK is set to a
value other than
255.255.255.255,
neither the network
ID nor the host ID
1s in the logical
operation result of
IP and MASK.
PEERIP in the
OMCH MO must be
a valid IP address
of Class A, B, or C,
and cannot be set
to 127.X.X.X or
0.X.X.X.
In an OMCH MO, if
PEERMASK is not
set to No (And no impact
255.255.255.255, Read & Write on the UE in idle N/A N/A
neither the network mode)
ID nor the host ID
1s in the logical
operation result of
PEERIP and
PEERMASK.
In an OMCH MO, IP
must be different
from PEERIP.
PEERMASK in an
OMCH MO must be
set to a valid mask
(0 is not allowed to
precede 1). In an
OMCH MO, this
parameter can be
set to
255.255.255.255
when BEAR is set
No (And no impact
to IPV4.
In an OMCH MO, if
mode)
PEERMASK is not
set to
255.255.255.255,
neither the network
ID nor the host ID
1s in the logical
operation result of
PEERIP and
PEERMASK.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the OMCH MO,
this parameter is
BEAR is set to Read & Write on the UE in idle N/A N/A
IPV4, and SN and mode)
SBT are set to valid
values.
valid IP address of
addition, it cannot
be set to the
reserved IP
addresses 127.x.x.x
or 0.x.x.x but can
be set to 0.0.0.0.
In an OMCH MO, if
BRT is set to YES
and one of DSTIP
and DSTMASK is
set to 0.0.0.0, the
other must be set to
0.0.0.0.
In an OMCH MO, if
BRT is set to YES,
the logical AND No (And no impact
operation result Read & Write on the UE in idle N/A N/A
between DSTIP mode)
and DSTMASK in
the OMCH MO
must be equal to
DSTIP. That is,
DSTIP in the
OMCH MO must be
set to a network IP
address.
In an OMCH MO, if
BEAR and BRT are
set to IPV4 and
YES, respectively,
DSTIP must be
different from IP.
In the OMCH MO,
this parameter is
valid only when
In the OMCH MO,

this parameter is
No (And no impact
valid only when
BEAR is set to
mode)
IPV4 and BRT is
set to YES.
In an OMCH MO,
this parameter must
be set to NEXTHOP
if SBT and BRT are
set to
ETH_COVERBOAR
D and YES,
respectively.
In an OMCH MO,
this parameter can No (And no impact
be set to NEXTHOP Read & Write on the UE in idle N/A N/A
or IF if SBT and mode)
BRT are set to
BASE_BOAR and
YES, respectively.
In an OMCH MO,
this parameter must
be set to IF if SBT
and BRT are set to
BACK_BOAR and
YES, respectively.
In an OMCH MO,
this parameter can
be set to PPP or
MPGRP if SBT is
set to
BASE_BOARD,
BRT is set to YES, No (And no impact
and RT is set to IF. Read & Write on the UE in idle N/A N/A
In an OMCH MO, mode)
this parameter must
be set to TUNNEL if
SBT is set to
BACK_BOARD,
BRT is set to YES,
and RT is set to IF.
In an OMCH MO,
this parameter can
be set to a value
within the range of
0 to 15 if IFT is set
to PPP.
In an OMCH MO,
this parameter can
No (And no impact
be set to a value
within the range of
mode)
0 to 3 if IFT is set to
MPGRP.
In an OMCH MO,
this parameter can
be set to a value
within the range of
0 to 14 if IFT is set
to TUNNEL.
In the OMCH MO,
No (And no impact
this parameter is
valid only when
mode)
BRT is set to YES.
In an OMCH MO,
NEXTHOP must be
different from IP. No (And no impact
In the OMCH MO, Read & Write on the UE in idle N/A N/A
this parameter is mode)
valid only when RT
is set to NEXTHOP.
In an OMCH MO,
this parameter must
be set to
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5. No (And no impact
In an OMCH MO, Read & Write on the UE in idle N/A N/A
this parameter can mode)
be set to
BASE_BOARD,
BACK_BOARD or
ETH_COVERBOAR
7.
In an OMCH6 MO,
LOCALIP6 must be
set to a global
unicast address.
In the OMCH6 MO,
LOCALIP6 cannot
be the same as
PEERIP6.
In an OMCH6 MO,
PEERIP6 must be
set to a global
No (And no impact
unicast address.
In the OMCH6 MO,
mode)
LOCALIP6 cannot
be the same as
PEERIP6.

In a
PACKETFILTER
MO, this parameter
can be set to any
value within the
range of 0 to 5 if
SBT is set to
ETH_COVERBOAR
D and PT is set to
ETH.
In a
PACKETFILTER
MO, this parameter
can be set to any
value within the
range of 0 to 2 if
SBT is set to
ETH_COVERBOAR
D and PT is set to
ETHTRK.
In a
PACKETFILTER
MO, this parameter
if SBT is set to
BASE_BOARD and
PT is set to ETH or
ETHTRK.
In a
PACKETFILTER
MO, this parameter
can be set to any
value within the
range of 0 to 14 if
SBT is set to
BACK_BOARD and
PT is set to
TUNNEL.
This parameter is
valid only when FM
is set to ADV_ACL
or ADV_AND_L2.

In a
PACKETFILTER
MO, this parameter
must be set to
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In a Read Only N/A N/A N/A
PACKETFILTER
MO, this parameter
can be set to
BASE_BOARD,
ETH_COVERBOAR
D, or
BACK_BOARD if


This parameter is
valid only when FM
is set to L2_ACL or
ADV_AND_L2.
IP in a
PINGFILTER MO
must be a valid IP
it cannot be set to
0.x.x.x or 127.x.x.x.
In the binary value

into which MASK in
a PINGFILTER MO
is converted, 0
cannot precede 1.
In addition, MASK
can be
255.255.255.255,
but cannot be
0.0.0.0.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

In a
PORTSECURITY
MO, this parameter
can be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SN is set to a
value within the
range of 0 to 5.
In a
PORTSECURITY
MO, this parameter
can be set to
BASE_BOARD or
ETH_COVERBOAR
7.
In a
PORTSECURITY
MO, this parameter
can be set to ETH
or E1T1 if SBT is
set to
BASE_BOARD.
In a
PORTSECURITY
MO, this parameter
must be set to
E1T1 if SBT is set
to
E1_COVERBOARD
.
In a
PORTSECURITY
MO, this parameter
must be set to ETH
if SBT is set to
ETH_COVERBOAR
D.
In the
PORTSECURITY
MO, this parameter
if SBT is set to
BASE_BOARD and
PT is set to ETH.
In the
PORTSECURITY
MO, this parameter
can be set to a
value within the
range of 0 to 3 if
SBT is set to
BASE_BOARD and
PT is set to E1T1.
In the
PORTSECURITY
MO, this parameter
can be set to a
value within the
range of 0 to 7 if
SBT is set to
E1_COVERBOARD
and PT is set to
E1T1.
In the
PORTSECURITY
MO, this parameter
can be set to a
value within the
range of 0 to 5 if
SBT is set to
ETH_COVERBOAR
D and PT is set to
ETH.
No (And no impact
mode)

In the PPPLNK
MO, this parameter
is valid only when
SN and SBT are
both set to valid
values.
In the PPPLNK
MO, this parameter
is valid only when
SN and SBT are
both set to valid
values.
In the PPPLNK
MO, this parameter
AUTH is set to PAP
or CHAP.
In the PPPLNK
MO, this parameter
AUTH is set to PAP
or CHAP.
In the E1T1 MO, if

WORKMODE is set
to E1_BA or
E1_UNBA, TSN
must be set to a
value other than
TS0; if
WORKMODE is set
to T1, TSN must be
the range of TS1 to
TS24, Other
timeslots are not
used.
LOCALIP in a
PPPLNK MO must
be a valid IP
address of class A,
it cannot be set to
the reserved IP
addresses 0.x.x.x
be set to 0.0.0.0.
In the PPPLNK
MO, IPMASK
cannot be set to
0.0.0.0 if LOCALIP
is not set to 0.0.0.0.
In the PPPLNK
MO, IPMASK must
be set to 0.0.0.0 if
LOCALIP is set to
0.0.0.0.
In the logical
operation result of
LOCALIP and
IPMASK in a
PPPLNK MO,
neither the network
ID nor host ID can
be all 0s or 1s after
being converted
into a binary value.
In a PPPLNK MO,
LOCALIP must be
different from
PEERIP.
IPMASK in the
PPPLNK MO must
be valid, that is, 0 is
not allowed to
precede 1. In
addition, it can be
set to 0.0.0.0 or
255.255.255.255.
In the PPPLNK
MO, IPMASK
cannot be set to
0.0.0.0 if LOCALIP
is not set to 0.0.0.0.
In the PPPLNK
MO, IPMASK must
be set to 0.0.0.0 if
LOCALIP is set to
0.0.0.0.
In the logical
operation result of
LOCALIP and
IPMASK in a
PPPLNK MO,
neither the network
ID nor host ID can
be all 0s or 1s after
being converted
into a binary value.
In a PPPLNK MO,
LOCALIP must be
different from
PEERIP.
PEERIP in a
PPPLNK MO must
be a valid IP
address of class A,
it can be set to Read Only N/A N/A N/A
0.0.0.0, but cannot
be set to the
reserved IP
addresses 0.x.x.x
or 127.x.x.x.
In the PPPLNK
MO, MAXMFLEN
must be larger than
MAXSFLEN and
the minimum
In the PPPLNK
MO, this parameter
is valid only when
MUXCP is set to
ENABLE.
In the PPPLNK
MO, MAXMFLEN
must be larger than
MAXSFLEN and
the minimum
difference is 2.
In the PPPLNK
MO, MRU must be
greater than or
equal to
MAXMFLEN.
In the PPPLNK
MO, this parameter
is valid only when
MUXCP is set to
ENABLE.
In the PPPLNK
MO, this parameter
MUXCP is set to
ENABLE.
In the PPPLNK
MO, MRU must be
greater than or Read Only N/A N/A N/A
equal to
MAXMFLEN.



In the PPPLNK
MO, FFDPHOLD
must be smaller
than FFAPHOLD.
In the PPPLNK
MO, FFDPHOLD
must be smaller
than FFAPHOLD.
In the PPPLINK
MO, this parameter
must be set to
E1_COVERBOARD
within the range of
0 to 5.
In the PPPLINK
MO, this parameter
must be set to
BASE_BOARD if

In a PRI2QUE MO,
No (And no impact
PRI0 must be
greater than or
mode)
equal to PRI1.
In a PRI2QUE MO,
PRI0 must be
greater than or
No (And no impact
equal to PRI1.
In a PRI2QUE MO,
mode)
PRI1 must be
greater than or
equal to PRI2.
In a PRI2QUE MO,
PRI1 must be
greater than or
No (And no impact
equal to PRI2.
In a PRI2QUE MO,
mode)
PRI2 must be
greater than or
equal to PRI3.
In a PRI2QUE MO,
PRI2 must be
greater than or
No (And no impact
equal to PRI3.
In a PRI2QUE MO,
mode)
PRI3 must be
greater than or
equal to PRI4.
In a PRI2QUE MO,
PRI3 must be
greater than or
No (And no impact
equal to PRI4.
In a PRI2QUE MO,
mode)
PRI4 must be
greater than or
equal to PRI5.
In a PRI2QUE MO,
PRI4 must be
greater than or
No (And no impact
equal to PRI5.
In a PRI2QUE MO,
mode)
PRI5 must be
greater than or
equal to PRI6.
In a PRI2QUE MO,
No (And no impact
PRI5 must be
greater than or
mode)
equal to PRI6.

In an RSCGRP MO,
this parameter can
be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D if SN is set to a
value within the
In an RSCGRP MO,
this parameter can
be set to
BASE_BOARD,
BACK_BOARD or
ETH_COVERBOAR
7.
In an RSCGRP MO,
this parameter can
be set to PPP,
MPGRP, ETH, or
ETHTRK if SBT is
set to
BASE_BOARD.
In an RSCGRP MO,
this parameter can
be set to TUNNEL if
SBT is set to
BACK_BOARD.
In an RSCGRP MO,
this parameter can
be set to PPP or
MPGRP if SBT is
set to
E1_COVERBOARD
.
In an RSCGRP MO,
this parameter can
be set to ETH or
ETHTRK if SBT is
set to
ETH_COVERBOAR
D.
this parameter can
be set to a value
within the range of
0 to 15 if PT is set
to PPP.
In an RSCGRP MO,
this parameter can
be set to a value
within the range of
to
ETH_COVERBOAR
D and PT is set to
ETH.
In an RSCGRP MO,
this parameter can
be set to a value
within the range of
to
ETH_COVERBOAR
D and PT is set to
ETHTRK.
In an RSCGRP MO,
this parameter can
be set to a value
within the range of
to BASE_BOARD
and PT is set to
ETH.
In an RSCGRP MO,
this parameter can
be set to a value
within the range of
to BASE_BOARD
and PT is set to
Before adding an
NodeToRscGroup
MO, ensure that the
associated
RSCGRP MO has
been configured.
In the RSCGRP
must be set to Read & Write on the UE in idle N/A N/A
KBPS if BEAR is mode)
set to IP.
equal to TXBW.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 1000000 if PT
is set to TUNNEL.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 1000000 if PT
is set to ETH or
ETHTRK.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of No (And no impact
32 to 150000 if SBT Read & Write on the UE in idle N/A N/A
is set to mode)
E1_COVERBOARD
and PT is set to
PPP or MPGRP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 1984 if SBT is
set to
BASE_BOARD and
PT is set to PPP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 31744 if SBT
is set to
this parameter can
be set to any value
within the range of
32 to 1000000 if PT
is set to TUNNEL.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 1000000 if PT
is set to ETH or
ETHTRK.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 540000 if SBT
is set to No (And no impact
E1_COVERBOARD Read & Write on the UE in idle N/A N/A
and PT is set to mode)
PPP or MPGRP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
set to
BASE_BOARD and
PT is set to PPP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
32 to 31744 if SBT
is set to
BASE_BOARD and
PT is set to
equal to TXCIR.
In an RSCGRP MO,
TXPBS must be
greater than or
equal to TXCBS.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
64 to 1000000 if PT
is set to TUNNEL.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
64 to 1000000 if PT
is set to ETH or
ETHTRK. No (And no impact
In an RSCGRP MO, Read & Write on the UE in idle N/A N/A
this parameter can mode)
be set to any value
within the range of
64 to 200000 if SBT
is set to
E1_COVERBOARD
and PT is set to
PPP or MPGRP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
set to
BASE_BOARD and
PT is set to PPP.
In an RSCGRP MO,
this parameter can
this parameter can
be set to any value
within the range of
64 to 1000000 if PT
is set to TUNNEL.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
64 to 1000000 if PT
is set to ETH or
ETHTRK.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
64 to 450000 if SBT
is set to No (And no impact
E1_COVERBOARD Read & Write on the UE in idle N/A N/A
and PT is set to mode)
PPP or MPGRP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
set to
BASE_BOARD and
PT is set to PPP.
In an RSCGRP MO,
this parameter can
be set to any value
within the range of
64 to 63488 if SBT
is set to
BASE_BOARD and
PT is set to
In the RSCGRP
MO, this parameter
is valid only when
BEAR is set to IP.
In the RSCGRP
No (And no impact
MO, this parameter
is valid only when
mode)
BEAR is set to IP.
In an RSCGRP MO,
TXCBS must be
greater than or
No (And no impact
equal to TXCIR.
In an RSCGRP MO,
mode)
TXPIR must be
greater than or
equal to TXCIR.
In an RSCGRP MO,
No (And no impact
RXPIR must be
greater than or
mode)
equal to RXCIR.
In an RSCGRP MO,
TXPBS must be
greater than or
No (And no impact
equal to TXPIR.
In an RSCGRP MO,
mode)
TXPIR must be
greater than or
equal to TXCIR.
In an RSCGRP MO,
No (And no impact
RXPIR must be
greater than or
mode)
equal to RXCIR.
In an RSCGRP MO,
TXPBS must be
greater than or
No (And no impact
equal to TXPIR.
In an RSCGRP MO,
mode)
TXPBS must be
greater than or
equal to TXCBS.


In the
RSCGRPALG MO,
if SN is within the
range from 0 to 5,
this parameter can
be set to
E1_COVERBOARD
or
ETH_COVERBOAR
D. Read Only N/A N/A N/A
In the
RSCGRPALG MO,
if SN is set to 6 or
7, this parameter
can be set to
BASE_BOARD,
BACK_BOARD, or
ETH_COVERBOAR
D.
In the
RSCGRPALG MO,
if SBT is set to
BASE_BOARD, this
parameter can be
set to PPP,
MPGRP, ETH, or
ETHTRK.
In the
RSCGRPALG MO,
if SBT is set to
BACK_BOARD, this
parameter can be
set to TUNNEL.
In the
RSCGRPALG MO,
if SBT is set to
E1_COVERBOARD
, this parameter can
be set to PPP or
MPGRP.
In the
RSCGRPALG MO,
if SBT is set to
ETH_COVERBOAR
D, this parameter
can be set to ETH
or ETHTRK.
if PT is set to
MPGRP, the value
range of this
parameter is from 0
to 3.
In the
RSCGRPALG MO,
if SBT is set to
BASE_BOARD and
PT is set to ETH,
this parameter can
be set to 0 or 1.
In the
RSCGRPALG MO,
if SBT is set to
ETH_COVERBOAR
D and PT is set to
ETH, the value
range of this Read Only N/A N/A N/A
parameter is from 0
to 5.
In the
RSCGRPALG MO,
if SBT is set to
BASE_BOARD and
PT is set to
ETHTRK, this
parameter can be
set to 0 or 1.
In the
RSCGRPALG MO,
if SBT is set to
ETH_COVERBOAR
D and PT is set to
ETHTRK, the value
range of this
parameter is from 0
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an RSCGRPALG
No (And no impact
MO, CCTTH must
be smaller than
mode)
CTTH.
In an RSCGRPALG
No (And no impact
MO, CCTTH must
be smaller than
mode)
CTTH.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
The LOCIP
parameter in the
SCTPLNK MO
must be a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
In an SCTPLNK
MO, LOCIP,
SECLOCIP,
PEERIP, and
SECPEERIP must
be mutually
different with the IP
address of 0.0.0.0
being excluded.
That is, SECLOCIP
and SECPEERIP
can be both set to
0.0.0.0, while
neither LOCIP nor
PEERIP can be set
to 0.0.0.0.
SECLOCIP in the
SCTPLNK MO
must be a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x,
but can be set to
0.0.0.0.
In an SCTPLNK
MO, LOCIP,
SECLOCIP,
PEERIP, and Read & Write Yes BS Less than 1 minute
SECPEERIP must
be mutually
address of 0.0.0.0
being excluded.
That is, SECLOCIP
and SECPEERIP
can be both set to
0.0.0.0, while
neither LOCIP nor
PEERIP can be set
to 0.0.0.0.
PEERIP in the
SCTPLNK MO
must be a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x.
In an SCTPLNK
MO, LOCIP,
SECLOCIP,
PEERIP, and
SECPEERIP must Read & Write Yes BS Less than 1 minute
be mutually
address of 0.0.0.0
being excluded.
That is, SECLOCIP
and SECPEERIP
can be both set to
0.0.0.0, while
neither LOCIP nor
PEERIP can be set
to 0.0.0.0.
SECPEERIP in the
SCTPLNK MO
must be a valid IP
address of Class A,
it cannot be set to
127.x.x.x or 0.x.x.x,
but can be set to
0.0.0.0.
In an SCTPLNK
MO, LOCIP,
SECLOCIP,
PEERIP, and Read & Write Yes BS Less than 1 minute
SECPEERIP must
be mutually
address of 0.0.0.0
being excluded.
That is, SECLOCIP
and SECPEERIP
can be both set to
0.0.0.0, while
neither LOCIP nor
PEERIP can be set
to 0.0.0.0.
In an SCTPLNK
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and smaller than
RTOMAX.
In an SCTPLNK
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and smaller than
RTOMAX.
In an SCTPLNK
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and smaller than
RTOMAX.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an SCTPLNK
MO, No (And no impact
MAXASSOCRETR Read & Write on the UE in idle N/A N/A
must be larger than mode)
MAXPATHRETR.
In an SCTPLNK
MAXPATHRETR.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In the SCTPLNK
AUTOSWITCH is mode)
set to ENABLE.


No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an SCTPLNK6
MO, LOCIP,
SECLOCIP,
PEERIP, and
SECPEERIP must
be mutually
address of 0 being Read & Write Yes BS Less than 1 minute
excluded. That is,
SECLOCIP and
SECPEERIP can
be both set to 0,
while neither LOCIP
nor PEERIP can be
set to 0.
In an SCTPLNK6
MO, LOCIP,
SECLOCIP,
PEERIP, and
SECPEERIP must
be mutually
address of 0 being Read & Write Yes BS Less than 1 minute
excluded. That is,
SECLOCIP and
SECPEERIP can
be both set to 0,
while neither LOCIP
nor PEERIP can be
set to 0.
In an SCTPLNK6
MO, LOCIP,
SECLOCIP,
PEERIP, and
SECPEERIP must
be mutually
address of 0 being
excluded. That is,
SECLOCIP and Read & Write Yes BS Less than 1 minute
SECPEERIP can
be both set to 0,
while neither LOCIP
nor PEERIP can be
set to 0.
In an SCTPLNK6
MO, PEERIP must
be set to a global
unicast address.
In an SCTPLNK6
MO, LOCIP,
SECLOCIP,
PEERIP, and
SECPEERIP must
be mutually
address of 0 being
excluded. That is,
SECLOCIP and
SECPEERIP can
be both set to 0,
while neither LOCIP
nor PEERIP can be
set to 0.
In an SCTPLNK6
MO, SECPEERIP
must be set to a
global unicast
address.
In an SCTPLNK6
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and smaller than
RTOMAX.
In an SCTPLNK6
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and smaller than
RTOMAX.
In an SCTPLNK6
MO, RTOINIT must
No (And no impact
be greater than or
equal to RTOMIN
mode)
and smaller than
RTOMAX.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In an SCTPLNK6
MAXPATHRETR.
In an SCTPLNK6
MAXPATHRETR.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)

No (And no impact
mode)
IP in the
SUBNETVLAN MO
must be a valid IP
It cannot be set to
127.x.x.x or 0.x.x.x.
MASK in the
SUBNETVLAN MO Read Only N/A N/A N/A
must be all 1s.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In a TACALG MO,
TRMULHOCACTH
No (And no impact
must be greater
than or equal to
mode)
TRMULGOLDCAC
TH.
In a TACALG MO,
TRMDLHOCACTH
No (And no impact
must be greater
than or equal to
mode)
TRMDLGOLDCAC
TH.
In a TACALG MO,
TRMULHOCACTH
must be greater
than or equal to
TRMULGOLDCAC
No (And no impact
TH.
In a TACALG MO,
mode)
TRMULGOLDCAC
TH must be greater
than or equal to
TRMULSILVERCA
CTH.
In a TACALG MO,
TRMDLHOCACTH
must be greater
than or equal to
TRMDLGOLDCAC
No (And no impact
TH.
In a TACALG MO,
mode)
TRMDLGOLDCAC
TH must be greater
than or equal to
TRMDLSILVERCA
CTH.
In a TACALG MO,
TRMULGOLDCAC
TH must be greater
than or equal to
TRMULSILVERCA
CTH. No (And no impact
In a TACALG MO, Read & Write on the UE in idle N/A N/A
TRMULSILVERCA mode)
CTH must be
greater than or
equal to
TRMULBRONZEC
ACTH.
In a TACALG MO,
TRMDLGOLDCAC
TH must be greater
than or equal to
TRMDLSILVERCA
CTH. No (And no impact
In a TACALG MO, Read & Write on the UE in idle N/A N/A
TRMDLSILVERCA mode)
CTH must be
greater than or
equal to
TRMDLBRONZEC
ACTH.
In a TACALG MO,
TRMULSILVERCA
CTH must be No (And no impact
greater than or Read & Write on the UE in idle N/A N/A
equal to mode)
TRMULBRONZEC
ACTH.
In a TACALG MO,
TRMDLSILVERCA
CTH must be No (And no impact
greater than or Read & Write on the UE in idle N/A N/A
equal to mode)
TRMDLBRONZEC
ACTH.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
In a TLDRALG MO,
TRMULLDRTRGT
No (And no impact
H must be greater
than
mode)
TRMULLDRCLRTH
.
In a TLDRALG MO,
TRMDLLDRTRGT
No (And no impact
H must be greater
than
mode)
TRMDLLDRCLRTH
.
In a TLDRALG MO,
TRMULLDRTRGT
H must be greater
than
TRMULLDRCLRTH
No (And no impact
.
In a TLDRALG MO,
mode)
TRMULLDRCLRTH
must be greater
than
TRMULMLDTRGT
H.
In a TLDRALG MO,
TRMDLLDRTRGT
H must be greater
than
TRMDLLDRCLRTH
No (And no impact
.
In a TLDRALG MO,
mode)
TRMDLLDRCLRTH
must be greater
than
TRMDLMLDTRGT
H.
In a TLDRALG MO,
TRMULLDRCLRTH
must be greater
than
TRMULMLDTRGT
No (And no impact
H.
In a TLDRALG MO,
mode)
TRMULMLDTRGT
H must be greater
than
TRMULMLDCLRT
H.
In a TLDRALG MO,
TRMDLLDRCLRTH
must be greater
than
TRMDLMLDTRGT
No (And no impact
H.
In a TLDRALG MO,
mode)
TRMDLMLDTRGT
H must be greater
than
TRMDLMLDCLRT
H.
In a TLDRALG MO,
TRMULMLDTRGT
No (And no impact
H must be greater
than
mode)
TRMULMLDCLRT
H.
In a TLDRALG MO,
TRMDLMLDTRGT
No (And no impact
H must be greater
than
mode)
TRMDLMLDCLRT
H.
No (And no impact
mode)
When
TRMULOLCSWITC
H in the TOLCALG
MO is set to ON,
the QoS of high-
priority services can
be ensured in the
case of transport
overload in the No (And no impact
uplink. When Read & Write on the UE in idle N/A N/A
TRMULOLCSWITC mode)
H in the TOLCALG
MO is set to OFF,
the QoS of high-
priority services
cannot be ensured
in the case of
transport overload
in the uplink.
If
TRMDLOLCSWITC
H in the TOLCALG
MO is set to ON,
the qualities of
high-priority
services are
ensured. If
No (And no impact
TRMDLOLCSWITC
H in the TOLCALG
mode)
MO is set to OFF,
the qualities of
high-priority
services may
deteriorate in the
case of transport
overload in the
downlink.
In a TOLCALG MO,
TRMULOLCTRIGT
H must be greater
than
TRMULOLCRELTH
No (And no impact
.
In the TOLCALG
mode)
MO,
TRMULOLCTRIGT
H is valid only when
TRMULOLCSWITC
H is set to ON.
In a TOLCALG MO,
TRMULOLCTRIGT
H must be greater
than
TRMULOLCRELTH No (And no impact
. Read & Write on the UE in idle N/A N/A
In the TOLCALG mode)
MO, this parameter
is valid only when
TRMULOLCSWITC
H is set to ON.
No (And no impact
mode)
In a TOLCALG MO,
TRMDLOLCTRIGT
H must be greater
than
TRMDLOLCRELTH No (And no impact
. Read & Write on the UE in idle N/A N/A
In the TOLCALG mode)
MO, this parameter
is valid only when
TRMDLOLCSWITC
H is set to ON.
In a TOLCALG MO,
TRMDLOLCTRIGT
H must be greater
than
TRMDLOLCRELTH
No (And no impact
.
In the TOLCALG
mode)
MO,
TRMDLOLCRELTH
is valid only when
TRMDLOLCSWITC
H is set to ON.
No (And no impact
mode)



Each TUNNEL MO
must have a unique
combination of
SCN, DCN, SSRN,
DSRN, SSN, and
DSN.
Each TUNNEL MO
must have a unique
combination of
SCN, DCN, SSRN,
DSRN, SSN, and
DSN.
Each TUNNEL MO
must have a unique
combination of
SCN, DCN, SSRN,
DSRN, SSN, and
DSN.
Each TUNNEL MO
must have a unique Services are
combination of interrupted until the
Read & Write Yes BS
SCN, DCN, SSRN, parameter is
DSRN, SSN, and correctly set.
DSN.
Each TUNNEL MO
Read & Write Yes BS
DSN.
Each TUNNEL MO
Read & Write Yes BS
DSN.

In the VLANCLASS
MO, this parameter
TRAFFIC is set to
USERDATA.
No (And no impact
mode)
No (And no impact
mode)
In a VLANMAP
MO, NEXTHOPIP
must be a valid IP
it cannot be set to
0.x.x.x or 127.x.x.x.
In the binary value

into which MASK in
a VLANMAP MO is
converted, 0 cannot
precede 1. In
addition, MASK can
be
255.255.255.255, Read Only N/A N/A N/A
but cannot be
0.0.0.0.
In a VLANMAP
MO, the logical
AND result of
NEXTHOPIP and
MASK cannot be 0.
This parameter
must be set to a No (And no impact
valid value when Read & Write on the UE in idle N/A N/A
the VLANMAP MO mode)
is being modified.
In the VLANMAP
VLANMODE is set mode)
to SINGLEVLAN.
In the VLANMAP
MO, this parameter
is valid only when
VLANMODE is set
to SINGLEVLAN.
valid when the Read & Write on the UE in idle N/A N/A
VLANMAP MO is mode)
being modified and
SETPRIO is
changed from
DISABLE to
ENABLE.
In the VLANMAP
MO, this parameter
is valid only when
VLANMODE is set
to VLANGROUP.
valid when the Read & Write on the UE in idle N/A N/A
VLANMAP MO is mode)
being modified and
VLANMODE is
changed from
SINGLEVLAN to
VLANGROUP.
In the VLANMAP
VLANMODE is set mode)
to SINGLEVLAN.
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
No (And no impact
mode)
Impact on Radio
Validation of Introduced in
Caution Network Attribute
Modification Version...
Performance
N/A N/A None V100R001C00 Equipment
The parameter
modification has no
None None V100R004C00 Equipment
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
None N/A None V100R001C00 Equipment



The BS should be
reset to validate the
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification takes
None effect after the cell None V100R001C00 Equipment
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification has no
impact on the
equipment.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.


The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.


The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.



The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
This parameter
must be consistent
with the network
plan. Otherwise, the
call drop rate
The parameter
increases and the
modification has no
None access success V100R003C00 Equipment
impact on the
rate decreases for
equipment.
users at the
coverage edge, and
the interference on
neighboring cells
increases.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.




The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
This parameter
must be consistent
with the network
The parameter plan. Otherwise, the
modification has no call drop rate
None V100R003C00 Equipment
impact on the increases and the
equipment. access success
rate decreases for
users at the
coverage edge.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.



The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The modification of
priorities will affect
The parameter
the selection order
modification has no
if the clock source None V100R001C01 Equipment
impact on the
is selected
equipment.
system.

The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The modification of
The parameter
the selection order
modification has no
when the clock None V100R001C01 Equipment
impact on the
source is selected
equipment.
system.

The BS should be
parameter
modification.

Only the TOD clock The BS should be
of input type can reset to validate the
serve as a clock parameter
source. modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The clock accuracy

is affected if there is
an excessively
The parameter
large difference
modification has no
(about 20 m) None V100R001C01 Equipment
impact on the
between the value
equipment.
of this parameter
and the actual
feeder length.

The modification of
The parameter
the selection order
modification has no
impact on the
source is selected
equipment.
system.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
This parameter
The parameter must be consistent
modification has no with the network
impact on the plan. Otherwise, the
equipment. location precision
decreases.
This parameter
The parameter must be consistent
modification has no with the network
impact on the plan. Otherwise, the
equipment. location precision
decreases.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The feeder delay

should be
calculated
according to the
actual length of the
feeder. Typically,
3.8 ns delay is
generated when
data passes one
meter feeder. For
an LTE TDD cell
whose radius is less
None N/A V100R001C01 Equipment
than 3 km, the
delay must be less
then 3 us; for an
LTE TDD cell
whose radius is
greater than 3 km,
the delay must be
less than 5 us.
Otherwise, the
service
performance is
affected.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The clock accuracy

is affected if there is
an excessively
The parameter
large difference (no
modification has no
less than 20 m) None V100R002C00 Equipment
impact on the
between the value
equipment.
of this parameter
and the actual
feeder length.



The parameter
modification has no
impact on the
equipment.
When the clock

source is selected
The parameter
modification has no
system, the None V100R001C01 Equipment
impact on the
modification of
equipment.
the selection order.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The parameter
The BS should be
should be
consistent with None V100R001C01 Equipment
parameter
modification.
server domain.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.

The modification of
The parameter
the selection order
modification has no
impact on the
source is selected
equipment.
system.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The modification of
The parameter
the selection order
modification has no
impact on the
source is selected
equipment.
system.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.


The parameter
modification has no
impact on the
equipment.

The parameter
modification takes
None effect after the None V100R003C00 Equipment
board is
automatically reset.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.









The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.







The parameter
modification has no
impact on the
equipment.










The parameter
modification has no
impact on the
equipment.





The parameter
modification has no
impact on the
equipment.



















The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The start time

should be earlier
than the end time. If The parameter
the start time is not modification has no
specified, the impact on the
default start time, equipment.
namely 2000-01-01
00:00:00, is used.
The end time
should be later than
the start time. If the The parameter
end time is not modification has no
specified, the impact on the
default end time, equipment.
namely 2037-12-31
23:59:59, is used.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.


The parameter
modification has no
impact on the
equipment.






If the manager is
The parameter
not specified, the
modification has no
EMU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the manager is
The parameter
not specified, the
modification has no
EMU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the actual
connection is The parameter
inconsistent with modification has no
the configuration, impact on the
the EMU cannot be equipment.
maintained.
The communication
address of the EMU
The parameter
is usually 2. If it is
modification has no
not 2, set it None V100R001C00 Equipment
impact on the
according to the
equipment.
physical DIP switch
settings.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.






If the manager is
The parameter
not specified, the
modification has no
FMU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the manager is
The parameter
not specified, the
modification has no
FMU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
The parameter
modification has no
impact on the
equipment.
The communication
address of the FMU
not 14, set it The parameter
according to the modification has no
settings of physical impact on the
DIP switch. equipment.
Otherwise, the
communication with
the FMU fails.
The parameter
modification has no
impact on the
equipment.
The FMU cannot be

The parameter
operated or
modification has no
maintained if no None V100R003C00 Equipment
impact on the
manager is
equipment.
specified.
The parameter
modification has no
impact on the
equipment.





If the manager is
The parameter
not specified, the
modification has no
TCU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the manager is
The parameter
not specified, the
modification has no
TCU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the actual
connection is
The parameter
inconsistent with
modification has no
the data None V100R001C00 Equipment
impact on the
configuration, the
equipment.
TCU cannot be
maintained.
The communication
address of the TCU
The parameter
modification has no
not 7, set it None V100R001C00 Equipment
impact on the
according to the
equipment.
physical DIP switch
settings.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.






The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
If the manager is
The parameter
not specified, the
modification has no
PMU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the manager is
The parameter
not specified, the
modification has no
PMU cannot be None V100R001C00 Equipment
impact on the
operated or
equipment.
maintained.
If the actual
connection is
The parameter
inconsistent with
modification has no
the data None V100R001C00 Equipment
impact on the
configuration, the
equipment.
PMU cannot be
maintained.
The communication
address must be
consistent with the The parameter
DIP switch settings modification has no
on the PMU. impact on the
Otherwise, the equipment.
communication
fails.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.










The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The INSTALLTYPE
The parameter
of the SC48200
modification has no
PMU is set to None V100R001C00 Equipment
impact on the
OUTER only. Do
equipment.
not modify it.
The battery of the
The parameter
SC48200 PMU is
modification has no
not related to this None V100R001C00 Equipment
impact on the
parameter. Do not
equipment.
modify it.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.




The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.








The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.




The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.





The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.








The parameter
modification takes
is automatically
reset.
The parameter
modification has no
impact on the
equipment.




The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.





The parameter
modification has no
impact on the
equipment.
The parameter
modification takes
is automatically
reset.
The parameter
modification has no
impact on the
equipment.




The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.






The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
modified, the cells
carried by the
RRUs behind the
breakpoint on the
The parameter
RRU chain become
modification has no
unavailable. The None V100R003C00 Equipment
impact on the
cells carried by the
equipment.
RRUs between
breakpoints 1 and 2
on the RRU ring
become
unavailable.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.




The parameter
modification has no
impact on the
equipment.





The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
None N/A None V100R003C00 Radio
The parameter
modification has no
None None V100R003C00 Radio
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.


The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A bearer of QCI 5
carries IMS
signaling that is
generally
transmitted together
with service data. It
is recommended
that the
ServiceIfHoCfgGrou
p MO has the same
configuration for
QCI 5 and the QCI
of the co-
The parameter transmitted service
modification has no data.
None V100R005C00 Radio
impact on the It is also
equipment. recommended that
QCIs of default
bearers be
configured to
prohibit handovers.
If QCIs of default
bearers are
configured to allow
handovers, the UE
is immediately
handed over to the
target frequency
after accessing the
network.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
If the values of
CounterCheckTimer
and
CounterCheckCoun
tNum are too small,
the counter check
procedures are
performed too
frequently, which
The parameter
wastes radio
modification has no
None interface resources. V100R001C01 Radio
impact on the
If the values are too
equipment.
large, the counter
check procedure
fails to be initiated
during a long time,
which results in the
failure to check the
HFN on the UE side
and that on the
eNodeB side.
If the values of
CounterCheckTimer
and
CounterCheckCoun
tNum are too small,
the counter check
procedures are
performed too
frequently, which
The parameter
wastes radio
modification has no
None interface resources. V100R001C01 Radio
impact on the
If the values are too
equipment.
large, the counter
check procedure
fails to be initiated
during a long time,
which causes the
failure to check the
HFN on the UE side
and that on the
eNodeB side.
to ON, a DRB is
released when the
counter check
detects an
The parameter unexpected result
modification has no in the DRB. If this
impact on the switch is set to OFF,
equipment. a DRB is not
released even if the
counter check
detects an
unexpected result
in the DRB.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The setting of this
parameter has an
impact on how long
the eNodeB will
wait for a response
message from the
MME. If this
parameter is set to
an extremely small
value, the eNodeB
waits for a period
shorter than the
transmission time
required by a
response message
The parameter
from the MME. If
modification has no
None this parameter is V100R005C00 Radio
impact on the
set to an extremely
equipment.
large value, the
eNodeB continues
waiting for a
response message
from the MME when
it cannot receive
the response
message due to a
fault. As a result,
resources are
wasted. To prevent
this problem, you
are advised to
retain the default
value.
The setting of this
parameter has an
impact on how long
the eNodeB will
wait for a response
message over the
X2 interface from a
peer eNodeB. If this
parameter is set to
an extremely small
value, the eNodeB
waits for a period
shorter than the
transmission time
required by a
response message
The parameter
from the peer
modification has no
None eNodeB. If this V100R005C00 Radio
impact on the
parameter is set to
equipment.
an extremely large
value, the eNodeB
continues waiting
for a response
message from the
peer eNodeB when
it cannot receive
the response
message due to a
fault. As a result,
resources are
wasted. To prevent
this problem, you
are advised to
retain the default
value.
The setting of this
parameter has an
impact on how long
the eNodeB will
wait for a response
message from a
UE. If this
parameter is set to
an extremely small
value, the eNodeB
waits for a period
shorter than the
transmission time
required by a
The parameter response message
modification has no from the UE. If this
impact on the parameter is set to
equipment. an extremely large
value, the eNodeB
continues waiting
for a response
message from the
UE when it cannot
receive the
response message
due to a fault. As a
result, resources
are wasted. To
prevent this
problem, you are
advised to retain
the default value.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
None none V100R004C00 Radio
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter If SRI adaptation is

modification has no enabled, the SRI
impact on the load in a cell is
equipment. increased.
set to
LCG_PROFILE_1,
non-GBR services
are classified into
high- and low-
The parameter
priority non-GBR
modification has no
None services. QoS of V100R003C00 Radio
impact on the
high-priority non-
equipment.
GBR services is
better ensured, but
there is a risk of
failure to maintain
QoS of low-priority
non-GBR services.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
ROHC helps reduce
header overhead.
The parameter The reduction is
modification has no especially
impact on the significant for
equipment. services with small
data packets, such
as VoIP services.
Packet transmission
The parameter
reliability and the
modification has no
None network link V100R001C01 Radio
impact on the
overhead are
equipment.
affected.
The parameter
The support for
modification has no
None different protocols is V100R001C01 Radio
impact on the
affected.
equipment.
set to a small value,
the eNodeB rejects
access of the UE
again for the same
The parameter
reason. If this
modification has no
None parameter is set to V100R001C00 Radio
impact on the
a large value, the
equipment.
UE cannot access
the network for a
long period of time,
which affects user
experience.
After T320 expires,

the dedicated
priorities indicated
in the
RRCConnectionRel
ease message
become invalid, and
the absolute
in the system
information take
effect. As the
absolute priorities in
the system
The parameter
information are
modification has no
None optional, frequency V100R002C00 Radio
impact on the
prioritization can be
equipment.
better guaranteed
during cell
reselection if the
are used. If the
value of this
parameter is too
large, cell
reselection
parameters cannot
be updated in time
at the UE when
priority values
change.
If the UE does not
complete an intra-
RAT handover
before this timer
The parameter expires, the UE
modification has no reverts back to the
impact on the associated
equipment. configuration and
initiates an RRC
connection
reestablishment
procedure.
If the UE does not

complete an inter-
RAT handover to
GERAN before this
The parameter timer expires, the
modification has no UE reverts back to
impact on the the associated
equipment. configuration and
initiates an RRC
connection re-
establishment
procedure.
After T320 expires,
the dedicated
in the
RRCConnectionRel
ease message
become invalid, and
the absolute
in the system
information take
effect. As the
absolute priorities in
the system
The parameter
information are
modification has no
None optional, frequency V100R002C00 Radio
impact on the
prioritization can be
equipment.
better guaranteed
during cell
reselection if the
are used. If the
value of this
parameter is too
large, cell
reselection
parameters cannot
be updated in time
at the UE when
priority values
change.
0, the RRC
connection for a UE
not performing
services will be
released when this
timer expires. If this
timer is set to a
small value, the
RRC connection for
a UE not
performing services
will be released
shortly after the UE
stops performing
services, resulting
in frequent RRC
connection
The parameter
requests from the
modification has no
None UE. If this timer is V100R001C00 Radio
impact on the
set to a large value,
equipment.
the RRC
connection for a UE
not performing
services may not be
released in a timely
manner after the
UE stops
performing
services, resulting
in waste of radio
resources. If this
timer is set to 0, the
RRC connection for
a UE not
performing services
will not be released,
also resulting in
a UE cannot enter
an out-of-
synchronization
state in a timely
manner. As a result,
the UE
unnecessarily
occupies PUCCH
and SRS resources
and the UE power
consumption
The parameter increases. If this
modification has no parameter is set to
impact on the a small value, there
equipment. is a probability that
the UE enters an
out-of-
synchronization
state when it should
not. As a result, the
number of random
access times for
maintaining uplink
synchronization
increases and more
resources for
random access are
used.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
If this switch is on,

The parameter
the PA is adjusted.
modification has no
None If this switch is off, V100R002C00 Radio
impact on the
the PA is not
equipment.
adjusted.
If the RS power is
fixed, setting this
parameter to a
large value
increases the
power and MCS of
all users in the cell,
The parameter but results in power
modification has no limitation. The
impact on the power limitation
equipment. reduces the UE
throughput. Setting
this parameter to a
small value
decreases the
power and MCS
and reduces the
cell throughput.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
None N/A none V100R001C01 Radio
When Ks is equal to
0, the transmit
power can be
adjusted according
to only closed-loop
TPC commands.
When Ks is equal to
1.25, the transmit
The parameter
power can be
modification has no
None adjusted by means V100R001C01 Radio
impact on the
of selecting different
equipment.
MCSs during
scheduling. This
helps the UE to
quickly adapt to
changes in channel
conditions and
increases the cell
throughput.
parameter is too
small, the transmit
power of the SRS is
too low, so that the
uplink timing
requirement is not
met and the SINR
of data channels
cannot be
measured
accurately. Thus,
The parameter
the network
modification has no
None performance V100R001C01 Radio
impact on the
deteriorates. If the
equipment.
value of this
parameter is too
large, the transmit
power of the SRS is
excessively high,
which increases the
interference to
other channels and
neighboring cells
and thus reduces
the throughput of
the entire network.

parameter is too
small, the transmit
power of the SRS is
too low, so that the
uplink timing
requirement is not
met and the SINR
of data channels
cannot be
measured
accurately. Thus,
The parameter
the network
modification has no
None performance V100R001C01 Radio
impact on the
deteriorates. If the
equipment.
value of this
parameter is too
large, the transmit
power of the SRS is
excessively high,
which increases the
interference to
other channels and
neighboring cells
and thus reduces
the throughput of
the entire network.
A greater value of
this parameter
indicates a smaller
impact of the
previous RSRP
value on the filtered
value and a greater
impact of the RSRP
value measured
The parameter
this time on the
modification has no
None filtered value. A V100R001C01 Radio
impact on the
equipment.
parameter indicates
a greater impact of
the previous RSRP
value on the filtered
value and a smaller
impact of the RSRP
value measured
this time on the
filtered value.
The parameter
modification has no
impact on the
equipment.
An appropriate
value of this
parameter
effectively reduces
the probability of
cross-cell
handovers and
The parameter therefore increases
modification has no the handover
impact on the success rate. A
equipment. smaller value of this
of distance-based
handovers. A larger
value of this

DRX introduces
extra delay to
scheduling.
Therefore, if a UE
with a service
whose QCI is
mapped to a high
requirement for the
delay is allowed to
enter the DRX
The parameter state, the QoS
modification has no satisfaction rate
impact on the decreases because
equipment. of the increase in
the delay of the
service. If a UE with
a service whose
QCI is mapped to a
low requirement for
the delay is not
allowed to enter the
DRX state, it is not
power-saving for
the UE.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
the UE enters
Sleep Time before
receiving the
retransmitted data,
resulting in failures
to correctly receive
The parameter
the retransmitted
modification has no
None data. If this V100R003C00 Radio
impact on the
parameter is set to
equipment.
a large value, the
UE keeps waiting
even when
retransmitted data
is lost. That is, the
UE stays active,
which is not power-
saving.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The entering
condition of event
A1 is as follows: Ms
- Hys > Thresh. The
of event A2 is as
follows: Ms + Hys <
Thresh. Ms is the
measurement value
of the serving cell,
The parameter
Hys is the
modification has no
None hysteresis for event V100R003C00 Radio
impact on the
A1 or A2 contained
equipment.
in the measurement
configuration, and
Thresh is the
threshold for the
particular event. A
larger value of Hys
results in a lower
probability of
triggering event A1
or A2.
The time-to-trigger
helps reduce the
number of inter-
RAT measurements
and prevent
unnecessary inter-
RAT
The parameter
measurements. The
modification has no
None larger the value of V100R003C00 Radio
impact on the
this parameter, the
equipment.
smaller the average
number of inter-
RAT
measurements, and
the higher the
probability of call
drops.
The entering
condition of event
- Hys > Thresh. A
larger value of
Thresh results in a
The parameter
modification has no
None triggering event A1 V100R003C00 Radio
impact on the
and therefore a
equipment.
stopping inter-RAT
measurements. A
smaller value of
Thresh leads to a
higher probability.
The entering
condition of event
- Hys > Thresh.
Thresh is the
threshold for this
event. A larger
The parameter value of Thresh
modification has no results in a lower
impact on the probability of
equipment. triggering event A1
and therefore a
stopping inter-RAT
measurements. A
smaller value of
Thresh leads to a
higher probability.
The entering
condition of event
+ Hys < Thresh.
Thresh is the
threshold for this
event. A larger
modification has no results in a higher
and therefore a
starting inter-RAT
measurements. A
smaller value of
Thresh leads to a
lower probability.
The entering
condition of event
+ Hys < Thresh.
Thresh is the
threshold for this
event. A larger
modification has no results in a higher
and therefore a
starting inter-RAT
measurements. A
smaller value of
Thresh leads to a
lower probability.
The parameter
modification has no
impact on the
equipment.

The entering
condition of event
B1 is as follows: Mn
+ Ofn - Hys >
Thresh.
Mn is the
measurement value
of the neighboring
cell. Ofn is the
frequency-specific
offset of the
neighboring cell.
Thresh is the
threshold for event
B1. Hys is the
The parameter
B1.
modification has no
None A larger value of V100R003C00 Radio
impact on the
Hys results in a
equipment.
triggering event B1
and hence causes
a lower probability
of handover. A large
value may affect
user experience. A
smaller value of
Hys leads to a
triggering event B1.
A small value may
cause handover
decision errors and
ping-pong
handovers.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
None handover to the V100R003C00 Radio
impact on the
CDMA2000 1xRTT
equipment.
cell, and a smaller
value leads to a
higher probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
CDMA2000 1xRTT
equipment.
cell, and a smaller
value leads to a
higher probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
CDMA2000 1xRTT
equipment.
cell, and a smaller
value leads to a
higher probability.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A larger value of
this parameter
results in a longer
average SRI period
for UEs in a cell
and a larger
capacity of SRI
The parameter users in the cell, but
modification has no it also lead to a
impact on the longer average
equipment. delay of uplink
scheduling for UEs
in the cell. A smaller
value of this
a smaller capacity
of SRI users in a
cell.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

+ Ofn - Hys >
Thresh.
Mn is the
measurement value
of the neighboring
cell. Ofn is the
frequency-specific
offset of the
neighboring cell.
Thresh is the
threshold for this
event. Hys is the
hysteresis for this
event, which is
used to prevent
frequent triggering
The parameter
of event evaluation
modification has no
None caused by radio V100R003C00 Radio
impact on the
signal fluctuation or
equipment.
fading.
A larger value of
Hys results in a
triggering event B1
and hence causes
a lower probability
value may affect
user experience. A
smaller value of
Hys leads to a
A small value may
cause handover
decision errors and
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
CDMA2000 HRPD
equipment.
cell, and a smaller
value leads to a
higher probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
CDMA2000 HRPD
equipment.
cell, and a smaller
value leads to a
higher probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
CDMA2000 HRPD
equipment.
cell, and a smaller
value leads to a
higher probability.

The entering
condition of event
+ Ofn - Hys >
Thresh.
Mn is the
measurement value
of the neighboring
cell. Ofn is the
frequency-specific
offset of the
neighboring cell.
Thresh is the
threshold for event
B1. Hys is the
The parameter
B1.
modification has no
impact on the
Hys results in a
equipment.
triggering event B1
and therefore a
handover. A large
value may affect
user experience. A
smaller value of
Hys leads to a
A small value may
cause handover
decision errors and
ping-pong
handovers.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
GERAN cell, and a
equipment.
smaller value leads
to a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
GERAN cell, and a
equipment.
smaller value leads
to a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
GERAN cell, and a
equipment.
smaller value leads
to a higher
probability.

A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN cell, and a
equipment.
smaller value leads
to a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN cell, and a
equipment.
smaller value leads
to a higher
probability.
The entering
condition of event
+ Ofn - Hys >
Thresh.
Mn is the
measurement value
of the neighboring
cell. Ofn is the
frequency-specific
offset of the
neighboring cell.
Thresh is the
threshold for event
B1. Hys is the
The parameter
B1.
modification has no
impact on the
Hys results in a
equipment.
triggering event B1
and therefore a
handover. A large
value may affect
user experience. A
smaller value of
Hys leads to a
A small value may
cause handover
decision errors and
ping-pong
handovers.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN cell, and a
equipment.
smaller value leads
to a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN cell, and a
equipment.
smaller value leads
to a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN cell, and a
equipment.
smaller value leads
to a higher
probability.
The triggering
condition of event
- Hys > Thresh.
The triggering
condition of event
+ Hys < Thresh.
Ms is the
measurement value
The parameter of the serving cell,
modification has no Hys is the
impact on the hysteresis for event
equipment. A1 or A2 contained
in the measurement
configuration, and
Thresh is the
threshold for the
particular event. A
larger value of Hys
results in a lower
probability of
triggering event A1
or A2.
The time-to-trigger
helps reduce the
number of inter-
frequency
measurements and
prevent
unnecessary inter-
The parameter frequency
modification has no measurements. The
impact on the larger the value of
equipment. this parameter, the
smaller the average
number of inter-
frequency
measurements, and
the higher the
probability of call
drops.
The entering
condition of event
- Hys > Thresh.
Thresh is the
threshold for the
event. A larger
value of Thresh
The parameter
results in a lower
modification has no
None probability of V100R003C00 Radio
impact on the
triggering event A1
equipment.
and hence causes
a lower probability
of stopping inter-
frequency
measurements. A
smaller value of
Thresh leads to a
higher probability.
The entering
condition of event
- Hys > Thresh.
Thresh is the
threshold for the
event. A larger
value of Thresh
The parameter
results in a lower
modification has no
impact on the
triggering event A1
equipment.
and hence causes
a lower probability
of stopping inter-
frequency
measurements. A
smaller value of
Thresh leads to a
higher probability.
The entering
condition of event
+ Hys < Thresh.
Thresh is the
threshold for the
event. A smaller
value of Thresh
The parameter
results in a lower
modification has no
impact on the
triggering event A2
equipment.
and hence causes
a lower probability
of starting inter-
frequency
measurements. A
larger value of
Thresh leads to a
higher probability.
The entering
condition of event
+ Hys < Thresh.
Thresh is the
threshold for the
event. A smaller
value of Thresh
The parameter
results in a lower
modification has no
impact on the
triggering event A2
equipment.
and hence causes
a lower probability
of starting inter-
frequency
measurements. A
larger value of
Thresh leads to a
higher probability.
A larger value of
this parameter
results in a lower
probability of
triggering event A4
and hence causes
a lower probability
The parameter
value may affect
modification has no
None user experience. A V100R003C00 Radio
impact on the
equipment.
parameter leads to
of triggering event
A4. A small value
may cause
handover decision
errors and ping-
pong handovers.
A larger value of
this parameter
results in a lower
probability of
triggering event A4
and hence causes
a lower probability
The parameter
value may affect
modification has no
impact on the
equipment.
parameter leads to
of triggering event
A4. A small value
may cause
handover decision
errors and ping-
pong handovers.
A larger value of
this parameter
results in a lower
probability of
triggering event A4
and hence causes
a lower probability
The parameter
value may affect
modification has no
impact on the
equipment.
parameter leads to
of triggering event
A4. A small value
may cause
handover decision
errors and ping-
pong handovers.
A larger value of
this parameter
results in a lower
probability of
handover to an
The parameter inter-frequency cell,
modification has no a smaller average
impact on the number of
equipment. handovers, and a
higher call drop
rate. A smaller
value of this
parameter leads to
A larger value of
this parameter
results in a lower
probability of
triggering event A4
and hence causes
a lower probability
The parameter
value may affect
modification has no
impact on the
equipment.
parameter leads to
of triggering event
A4. A small value
may cause
handover decision
errors and ping-
pong handovers.
A larger value of
this parameter
results in a lower
probability of
triggering event A4
and hence causes
a lower probability
The parameter
value may affect
modification has no
impact on the
equipment.
parameter leads to
of triggering event
A4. A small value
may cause
handover decision
errors and ping-
pong handovers.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A larger value of
this parameter
results in a lower
probability of
triggering event A3
and therefore a
The parameter
modification has no
None handover. A smaller V100R003C00 Radio
impact on the
value of this
equipment.
parameter leads to
of triggering event
A3 and therefore a
handover.
The entering
condition of event
- Hys > Thresh.
Thresh is the
threshold for the
event. A large value
The parameter of Thresh results in
modification has no a low probability of
impact on the triggering event A1
equipment. and hence causes
stopping inter-
frequency
measurements. A
small value of
Thresh leads to a
high probability.
The entering
condition of event
+ Hys < Thresh.
Thresh is the
threshold for the
event. A small value
The parameter of Thresh results in
modification has no a low probability of
impact on the triggering event A2
equipment. and hence causes
starting inter-
frequency
measurements. A
large value of
Thresh leads to a
high probability.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

A larger value of
this parameter
results in a lower
probability of
triggering event A3
and hence causes
a lower probability
The parameter
value may affect
modification has no
impact on the
equipment.
parameter leads to
of triggering event
A3. A small value
may cause
handover decision
errors and ping-
pong handovers.
A positive value of
this parameter
results in a
relatively low
probability of
triggering event A3
and therefore a
relatively low
The parameter
probability of
modification has no
None handover. A V100R003C00 Radio
impact on the
negative value of
equipment.
this parameter
leads to a relatively
high probability of
triggering event A3
and therefore a
relatively high
probability of
handover.
This parameter
helps reduce the
average number of
handovers and the
number of
unexpected
handovers, and
The parameter hence prevents
modification has no unnecessary
impact on the handovers. A larger
equipment. value of this
a smaller average
number of
handovers, but it
also leads to a
higher risk of call
drops.
The parameter
modification has no
impact on the
equipment.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The parameter
modification takes
None effect after the cell None V100R003C00 Radio
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
If the ARP value of

The parameter a bearer is the
modification has no same as the value
impact on the of this parameter,
equipment. the UE throughput
will be limited.
If the ARP value of
The parameter a bearer is the
modification has no same as the value
impact on the of this parameter,
equipment. the UE throughput
will be limited.
The BS should be
parameter
modification.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The link should be

reestablished after
the parameter
modification.
The link should be

reestablished after
the parameter
modification.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.


The parameter
modification has no
impact on the
equipment.

The parameter
modification has no
impact on the
equipment.
The link should be

reestablished after
the parameter
modification.
The link should be

reestablished after
the parameter
modification.
The link should be

reestablished after
the parameter
modification.
This parameter has
an impact on
The parameter
automatic removal
modification has no
None of the X2 interface V100R001C01 Radio
impact on the
in a situation where
equipment.
the peer eNodeB is
removed.

set to ON, the UE
may enter the DRX
The parameter
state, saving UE
modification has no
None power. If this V100R001C01 Radio
impact on the
parameter is set to
equipment.
OFF, the UE
consumes relatively
much power.
This parameter has

The parameter little impact on the
modification has no radio network
impact on the performance. Short
equipment. DRX cycles reduce
the traffic delay.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

IMS signaling and
low-delay services
are prioritized
during scheduling
but consume many
resources to ensure
The parameter their QoS.
modification has no Therefore, it is
impact on the recommended that
equipment. this parameter not
be set to
IMSSignalling or
LowDelay for TCP
services and non-
real-time streaming
services.
This parameter has

an impact on the
The parameter
throughput and the
modification has no
None QoS differentiation V100R001C00 Radio
impact on the
service. Its value is
equipment.
subject to the
operator's policy.
This parameter has

an impact on the
The parameter
throughput and the
modification has no
impact on the
equipment.
subject to the
operator's policy.
a large uplink
transmission
bandwidth is
reserved for non-
GBR services and a
large Min_GBR
(minimum
guaranteed bit rate)
of non-GBR
services can be
guaranteed.
However, when the
transmission
bandwidth is
limited, the number
The parameter
of admitted non-
modification has no
None GBR services is V100R002C00 Radio
impact on the
small.
equipment.
a small uplink
transmission
bandwidth is
reserved for non-
GBR services and a
small Min-GBR of
non-GBR services
can be guaranteed.
However, when the
transmission
bandwidth is
limited, the number
of admitted non-
GBR services is
large.
the Min_GBR
(minimum
of high-priority non-
GBR services can
be guaranteed but
the Min_GBR of
low-priority non-
GBR services
The parameter
cannot be
modification has no
None guaranteed when V100R002C00 Radio
impact on the
resources are
equipment.
insufficient.
there is an impact
on the response
time of non-GBR
services when
resources are
insufficient and
there are higher-
priority services.
This parameter
affects the pre-
allocation
probability of its
The parameter corresponding type
modification has no of service and
impact on the therefore affects the
equipment. service delay. The
delay has a
negative correlation
with the pre-
allocation weight.
The parameter
modification has no
impact on the
equipment.
set to
PBR_0_KBps,
there is a risk that
the corresponding
services will never
be scheduled. If this
The parameter
parameter is set to
modification has no
None PBR_INFINITY and V100R003C00 Radio
impact on the
the corresponding
equipment.
traffic volume is
high, there is a risk
that the services
with QCIs indicating
lower priorities than
this QCI will never
be scheduled.
Services with
The parameter
relatively high
modification has no
None priorities are V100R005C00 Radio
impact on the
scheduled
equipment.
preferentially.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
set to
The parameter
REDIRECTION for
modification has no
None a bearer with a QCI V100R003C00 Radio
impact on the
of 1, call drop
equipment.
occurs during a
redirection.
The parameter
modification has no
impact on the
equipment.
set to
The parameter
REDIRECTION for
modification has no
None a bearer with a QCI V100R003C00 Radio
impact on the
of 1, call drop
equipment.
occurs during a
redirection.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

a long delay of
services and a
failure to meet the
The parameter
QCI requirement. A
modification has no
None small value of this V100R003C00 Radio
impact on the
parameter leads to
equipment.
a severe case of
PDCP data
discarding and
therefore low
throughput.
The parameter
modification has no
impact on the
equipment.
leads to a higher
interference
resistance
capability, but a
larger number of
retransmissions
results in a longer
delay and lower
throughput. Set this
parameter to a
small value for
services with a high
requirement for the
delay and to a large
value for services
with a low
requirement for the
The parameter delay. RRC
modification has no connection re-
impact on the establishment has a
equipment. great impact on
Acknowledged
Mode (AM)
services, such as
packet-loss-
sensitive and delay-
insensitive TCP
services, because
packets in the
buffer are discarded
upon the re-
establishment.
Therefore, a large
value of this
parameter is
recommended,
reducing the
probability of RRC
leads to a higher
interference
resistance
capability, but a
larger number of
retransmissions
results in a longer
delay and lower
throughput. Set this
parameter to a
small value for
services with a high
requirement for the
delay and to a large
value for services
with a low
requirement for the
The parameter delay. RRC
modification has no connection re-
impact on the establishment has a
equipment. great impact on
Acknowledged
Mode (AM)
services, such as
packet-loss-
sensitive and delay-
insensitive TCP
services, because
packets in the
buffer are discarded
upon the re-
establishment.
Therefore, a large
value of this
parameter is
recommended,
reducing the
probability of RRC
To prevent buffer
overflow caused by
an excessively long
queue, the
transmitter sends
status reports
based on the data
The parameter volume of
modification has no transmitted PDUs. A
impact on the small value of this
equipment. parameter results in
a low frequency of
sending polling
PDUs. A large value
leads to high buffer
occupancy and a
slow speed of send
window movement.
To prevent buffer
overflow caused by
an excessively long
queue, the
transmitter sends
status reports
based on the data
The parameter volume of
modification has no transmitted PDUs. A
impact on the small value of this
equipment. parameter results in
a low frequency of
sending polling
PDUs. A large value
leads to high buffer
occupancy and a
slow speed of send
window movement.
To prevent the send
window from
changing to 0, the
transmitter initiates
status reporting
based on the
number of PDUs. A
small value (smaller
than or equal to
PollPdu_p16) of
this parameter
results in a high
frequency of
sending polling
The parameter PDUs, a short
modification has no round-trip time for
impact on the RLC packets, and a
equipment. high speed of send
window movement.
If the send window
is not 0, however, a
small value does
not increase the
transmission speed;
instead, it leads to
an excessive
number of status
reports. A large
value of this
a low speed of send
window movement.
To prevent the send
window from
changing to 0, the
transmitter initiates
status reporting
based on the
number of PDUs. A
small value (smaller
than or equal to
PollPdu_p16) of
this parameter
results in a high
frequency of
sending polling
The parameter PDUs, a short
modification has no round-trip time for
impact on the RLC packets, and a
equipment. high speed of send
window movement.
If the send window
is not 0, however, a
small value does
not increase the
transmission speed;
instead, it leads to
an excessive
number of status
reports. A large
value of this
a low speed of send
window movement.
too many polling
PDUs are sent. In
addition, the
number of ARQ
retransmissions
reaches its
The parameter
maximum due to
modification has no
None consecutive PDU V100R003C00 Radio
impact on the
retransmissions,
equipment.
and therefore the
RRC connection is
re-established. If
this parameter is
status reports
cannot be sent in
time.
too many polling
PDUs are sent. In
addition, the
number of ARQ
retransmissions
reaches its
The parameter
maximum due to
modification has no
None consecutive PDU V100R003C00 Radio
impact on the
retransmissions,
equipment.
and therefore the
RRC connection is
re-established. If
this parameter is
status reports
cannot be sent in
time.
This parameter has
an impact on status
reporting in AM. A
low frequency of
status reporting
leads to a low
frequency of status
report scheduling
but a high
probability that the
send window
changes to 0 at the
transmitter, thereby
reducing the
transmission rate. A
high frequency of
The parameter
status reporting
modification has no
None leads to a high V100R003C00 Radio
impact on the
probability of timely
equipment.
acknowledgment to
data in the send
window and
therefore a high
probability of rate
guarantee.
However, a high
frequency of status
reporting results in
a high probability of
status report
scheduling and
repeated
transmissions,
thereby wasting
resources.
This parameter has
an impact on status
reporting in AM. A
low frequency of
status reporting
leads to a low
frequency of status
report scheduling
but a high
probability that the
send window
changes to 0 at the
transmitter, thereby
reducing the
transmission rate. A
high frequency of
The parameter
status reporting
modification has no
None leads to a high V100R003C00 Radio
impact on the
probability of timely
equipment.
acknowledgment to
data in the send
window and
therefore a high
probability of rate
guarantee.
However, a high
frequency of status
reporting results in
a high probability of
status report
scheduling and
repeated
transmissions,
thereby wasting
resources.
A small value of this
useless HARQ
retransmissions
from the transmitter
and repeated status
reports from the
receiver, thereby
wasting resources.
The parameter
parameter leads to
modification has no
None a long delay for the V100R003C00 Radio
impact on the
receiver to
equipment.
determine an out-
of-order packet
transmission failure
and therefore a
long delay for
sending status
reports, thereby
delaying services
and reducing the
throughput.
useless HARQ
retransmissions
and repeated status
reports from the
receiver, thereby
wasting resources.
The parameter
parameter leads to
modification has no
None a long delay for the V100R003C00 Radio
impact on the
receiver to
equipment.
determine an out-
of-order packet
transmission failure
and therefore a
long delay for
sending status
reports, thereby
delaying services
and reducing the
throughput.
The PDCP
sequence number
size must be large
enough to prevent
Hyper Frame
Number (HFN)
The parameter
mismatch caused
modification has no
None by loss of a large V100R003C00 Radio
impact on the
number of packets.
equipment.
However, a longer
PDCP sequence
number results in
more PDCP header
overhead and lower
payload throughput.
The sequence
number size
specified by this
parameter must be
large enough to
The parameter
prevent sequence
modification has no
None number ambiguity V100R003C00 Radio
impact on the
caused by HARQ
equipment.
retransmissions.
However, a large
size results in a
heavy RLC header
load.
The sequence
number size
specified by this
parameter must be
large enough to
The parameter
prevent sequence
modification has no
None number ambiguity V100R003C00 Radio
impact on the
caused by HARQ
equipment.
retransmissions.
However, a large
size results in a
heavy RLC header
load.
useless HARQ
retransmissions
and a large number
of lost packets. A
The parameter large value of this
modification has no parameter leads to
impact on the a long delay for the
equipment. receiver to
determine an out-
of-order packet
transmission failure,
thereby delaying
services and
reducing the
throughput.
useless HARQ
retransmissions
and a large number
of lost packets. A
The parameter large value of this
modification has no parameter leads to
impact on the a long delay for the
equipment. receiver to
determine an out-
of-order packet
transmission failure,
thereby delaying
services and
reducing the
throughput.
set to FALSE, the
target eNodeB will
transmit all data
The parameter forwarded by the
modification has no source eNodeB.
impact on the Part of the data
equipment. may already be
transmitted to UEs,
thereby wasting
resources on the air
interface.
This parameter has

an impact on the
The parameter
throughput and the
modification has no
impact on the
equipment.
subject to the
operator's policy.
This parameter has

an impact on the
The parameter
throughput and the
modification has no
impact on the
equipment.
subject to the
operator's policy.
a large uplink
transmission
bandwidth is
reserved for non-
GBR services and a
large Min_GBR
(minimum
of non-GBR
services can be
guaranteed.
However, when the
transmission
bandwidth is
limited, the number
The parameter
of admitted non-
modification has no
None GBR services is V100R003C00 Radio
impact on the
small.
equipment.
a small uplink
transmission
bandwidth is
reserved for non-
GBR services and a
small Min-GBR of
non-GBR services
can be guaranteed.
However, when the
transmission
bandwidth is
limited, the number
of admitted non-
GBR services is
large.
the Min_GBR
(minimum
of high-priority non-
GBR services can
be guaranteed but
the Min_GBR of
low-priority non-
GBR services
The parameter
cannot be
modification has no
None guaranteed when V100R003C00 Radio
impact on the
resources are
equipment.
insufficient.
there is an impact
on the response
time of non-GBR
services when
resources are
insufficient and
there are higher-
priority services.
This parameter
affects the pre-
allocation
probability of its
The parameter corresponding type
modification has no of service and
impact on the therefore affects the
equipment. service delay. The
delay has a
negative correlation
with the pre-
allocation weight.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
set to
PBR_0_KBps,
there is a risk that
the corresponding
services will never
be scheduled. If this
The parameter
parameter is set to
modification has no
None PBR_INFINITY and V100R003C00 Radio
impact on the
the corresponding
equipment.
traffic volume is
high, there is a risk
that the services
with QCIs indicating
lower priorities than
this QCI will never
be scheduled.
Services with
The parameter
relatively high
modification has no
None priorities are V100R003C00 Radio
impact on the
preferentially
equipment.
scheduled.
The parameter
modification has no
impact on the
equipment.
This parameter and

other associated
factors have an
impact on the CQI
reporting mode and
The parameter
reporting
modification has no
None parameters, and V100R003C00 Radio
impact on the
therefore affect the
equipment.
feedback overhead
in the uplink and
throughput or
coverage in the
downlink.
The setting of this
parameter
determines the
transmission modes
The parameter that apply to UEs
modification has no served by a multi-
impact on the antenna eNodeB
equipment. and therefore
affects performance
such as the
throughput and
coverage.
The setting of this
parameter
determines the
transmission modes
affects performance
such as the
throughput and
coverage.
The setting of this

parameter
determines the
The parameter
modification has no
None CQI reporting V100R005C00 Radio
impact on the
period, affecting the
equipment.
UE throughput and
number of UEs
supported by a cell.
When
CqiPeriodAdaptive
is set to OFF, the
setting of this
parameter
determines the CQI
The parameter period. A smaller
modification has no value of this
impact on the parameter results in
equipment. high UE throughput
but fewer UEs that
can participate in
CQI reporting. A
The setting of this
parameter
determines the
transmission modes
affects performance
such as the
throughput and
coverage.
The setting of this
parameter
determines the
transmission modes
affects performance
such as the
throughput and
coverage.
This parameter
affects the
configuration of
The parameter
SRS periods for
modification has no
None UEs and therefore V100R005C00 Radio
impact on the
affects the UE
equipment.
throughput and
number of UEs
supported by a cell.
When
SrsPeriodAdaptive
is set to OFF, the
setting of this
parameter
determines the
The parameter
SRS period. A
modification has no
None smaller value of this V100R005C00 Radio
impact on the
equipment.
fewer UEs that can
participate in SRS
reporting. A larger
value of this

The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A decrease in the
value of this
parameter indicates
a decrease in the
number of
candidate cells for
each handover. In
The parameter
this case, the
modification has no
None success rate of the V100R001C00 Radio
impact on the
handover triggered
equipment.
by each
measurement
report is decreased,
but the required
amount of radio
interface resource
is reduced.
When the value is

increased, the
number of reports
increases and the
handover success
The parameter
rate rises. An
modification has no
None excessively large V100R001C00 Radio
impact on the
number of reports,
equipment.
however, results in
excessive signaling
and hence causes
a waste of radio
interface resources.
A smaller value of
this parameter
results in a larger
number of reports
and greater
consumption of
radio interface
resources. A larger
value of this
The parameter
parameter leads to
modification has no
None a longer delay of V100R001C00 Radio
impact on the
handover retries
equipment.
and hence a lower
handover success
rate. In the early
stage of LTE
deployment, this
parameter should
be set to a small
value to ensure
timely handovers.
The parameter
modification has no
impact on the
equipment.
A smaller value of
this parameter
results in a larger
number of reports,
greater
consumption of
radio interface
The parameter
resources and a
modification has no
None higher handover V100R001C00 Radio
impact on the
success rate. A
equipment.
parameter leads to
a longer delay of
handover retries
and thus a lower
handover success
rate.
The parameter
modification has no
impact on the
equipment.
A smaller value of
this parameter
results in a larger
number of reports
and greater
consumption of
radio interface
resources. A larger
value of this
The parameter
parameter leads to
modification has no
impact on the
handover retries
equipment.
and hence a lower
handover success
rate. In the early
stage of LTE
deployment, this
parameter should
be set to a small
value to ensure
timely handovers.
The parameter
modification has no
impact on the
equipment.
A smaller value of
this parameter
results in a larger
number of reports
and greater
consumption of
radio interface
resources. A larger
value of this
The parameter
parameter leads to
modification has no
impact on the
handover retries
equipment.
and hence a lower
handover success
rate. In the early
stage of LTE
deployment, this
parameter should
be set to a small
value to ensure
timely handovers.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A decrease in the
value of this
parameter indicates
a decrease in the
number of
candidate cells for
each handover. In
The parameter
this case, the
modification has no
None success rate of the V100R001C00 Radio
impact on the
handover triggered
equipment.
by each
measurement
report is decreased,
but the required
amount of radio
interface resource
is reduced.
When the value is

increased, the
number of reports
increases and the
handover success
The parameter
rate rises. An
modification has no
None excessively large V100R001C00 Radio
impact on the
number of reports,
equipment.
however, results in
excessive signaling
and hence causes
a waste of radio
interface resources.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A smaller value of
this parameter
results in a larger
number of reports,
greater
consumption of
radio interface
The parameter
resources and a
modification has no
impact on the
success rate. A
equipment.
parameter leads to
a longer delay of
handover retries
and therefore a
lower handover
success rate.
set to BOTH, both
measured RSRP
and RSRQ values
are reported. In this
situation, a
handover is
triggered only when
both the measured
values meet the
corresponding
conditions,
The parameter
preventing
modification has no
None unnecessary V100R001C00 Radio
impact on the
handovers.
equipment.
set to
SAME_AS_TRIG_
QUAN, the
measurement
quantity included in
the measurement
report for event A4
is the same as the
evaluation for the
related event A2.
A smaller value of
this parameter
results in a larger
number of reports,
greater
consumption of
radio interface
The parameter
resources and a
modification has no
impact on the
success rate. A
equipment.
parameter leads to
a longer delay of
handover retries
and thus a lower
handover success
rate.
set to BOTH, the
eNodeB sends UEs
two measurement
configurations for
events A1 and A2:
one based on
RSRP, and the
The parameter other based on
modification has no RSRQ. When the
impact on the triggering condition
equipment. specified by either
configuration for
event A1 or A2 is
fulfilled, the
corresponding
event is reported
and inter-frequency
measurements are
stopped or started.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN cell, and a
equipment.
smaller value
results in a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
GERAN cell, and a
equipment.
smaller value
results in a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
None handover to V100R002C00 Radio
impact on the
CDMA2000, and a
equipment.
smaller value
results in a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN, and a
equipment.
smaller value
results in a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
UTRAN, and a
equipment.
smaller value
results in a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
GERAN cell, and a
equipment.
smaller value
results in a higher
probability.
A larger value of
this parameter
results in a lower
The parameter
probability of
modification has no
impact on the
CDMA2000, and a
equipment.
smaller value
results in a higher
probability.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
aCfgInd in SIB2 is
set to CFG, the UE
draws a random
number 'rand' that
is uniformly
distributed in the
range [0,1). If rand
is smaller than the
value of this
parameter, the UE
considers access to
the cell as allowed.
That is, an RRC
connection can be
set up for the
mobile-originated
call. If this
The parameter
parameter is set to
modification has no
None a large value, the V100R001C00 Radio
impact on the
probability of
equipment.
allowing access to
the cell is high,
which may lead to a
high cell load. If this
parameter is set to
a small value, the
probability of
allowing access to
the cell is low, in
which situation UEs
may fail to access
the cell even when
the cell load is
relatively light.This
valid for access
classes 0 to 9, but
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
aCfgInd or
AcBarringForMoSig
CfgInd in SIB2 is
set to CFG, the UE
draws a random
number 'rand' that
is uniformly
distributed in the
range [0,1). If rand
is smaller than the
value of this
parameter, the UE
considers access to
the cell as allowed.
That is, the RRC
connection can be
set up for the
The parameter signaling. If this
modification has no parameter is set to
impact on the a large value, the
equipment. probability of
allowing access to
the cell is high,
which may lead to a
high cell load. If this
parameter is set to
a small value, the
probability of
allowing access to
the cell is low, in
which situation UEs
may fail to access
the cell even when
the cell load is
relatively light.This
valid for access
classes 0 to 9, but
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.
The parameter
modification takes
is automatically
reset.

With other cell
reselection
parameters
unchanged, a larger
value of this
parameter indicates
a lower probability
of reselection to an
The parameter intra-frequency or
modification has no same-priority
impact on the neighboring cell,
equipment. leading to an
increased service
drop rate. A smaller
value of this
parameter indicates
a higher probability,
leading to a larger
number of pingpong
cell reselections.
The parameter
modification has no
impact on the
equipment.
A larger value of
this parameter
leads to a lower
probability of the
UE entering the
The parameter high-mobility or
modification has no medium-mobility
impact on the state and a smaller
equipment. impact of the
mobility status on
cell reselection. A
parameter leads to
A larger value of
this parameter
leads to a lower
probability of the
UE entering the
The parameter normal mobility
modification has no state, a lower
equipment. adjustment of
reselection-related
parameters, and a
smaller impact of
UE speed variation
on cell reselection.
A larger value of
this parameter
indicates a lower
probability of a UE
entering the
medium mobility
state. In this case,
The parameter
the reselection-
modification has no
None related parameters V100R001C00 Radio
impact on the
are not adjusted
equipment.
and cell
reselections are
more difficult to
trigger. A smaller
value of this
parameter leads to
A larger value of
this parameter
indicates a lower
probability of a UE
entering the high
mobility state. In
The parameter this case,
modification has no reselection-related
impact on the parameters are not
equipment. adjusted and cell
reselections are
more difficult to
trigger. A smaller
value of this
parameter leads to
A smaller value of
this parameter
results in a greater
impact of the UE
The parameter mobility state on the
modification has no hysteresis for cell
impact on the reselection, that is,
equipment. results in a higher
probability of cell
value leads to a
smaller impact.
A smaller value of
this parameter
impact of the UE
modification has no hysteresis for cell
impact on the reselection, that is,
equipment. results in a higher
probability of cell
value leads to a
smaller impact.
The parameter
modification has no
impact on the
equipment.
With other
conditions
unchanged, a larger
value of this
parameter leads to
The parameter
modification has no
None of triggering inter- V100R001C00 Radio
impact on the
frequency or inter-
equipment.
RAT
measurements, and
a smaller value
indicates a lower
probability.
A smaller value of
this parameter
The parameter indicates a lower
modification has no frequency of the
impact on the reselection to a low
equipment. priority inter-
frequency/inter-RAT
cell.
A larger value of
this parameter
indicates a higher
probability of a UE
The parameter
camping on the
modification has no
None cells assigned with V100R001C00 Radio
impact on the
the same frequency
equipment.
as the serving one,
and a smaller value
indicates a lower
probability.
The greater the
parameter, the
more difficult for the
cell to meet the S
criterion, the more
difficult for the cell
to become Suitable
Cell. The difficulty
level of the cell
selection is
increased. The
The parameter smaller the
modification has no parameter, the
impact on the easier for the cell to
equipment. meet the S
criterion, the easier
for the cell to
become Suitable
Cell. The difficulty
level of the cell
selection is
decreased. The
selected cell should
provide the signal
quality for the basic
services.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
With other
conditions
unchanged, a larger
value of this
The parameter parameter indicates
modification has no a higher probability
impact on the of triggering intra-
equipment. frequency
measurements, and
a smaller value
indicates a lower
probability.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
When this value is

increased, the
selection of the
The parameter
intra-frequency cell
modification has no
None becomes more V100R001C00 Radio
impact on the
difficult. When the
equipment.
value is decreased,
the selection
becomes easier.
The parameter
modification has no
impact on the
equipment.
A smaller value of
this parameter
impact of the UE
modification has no cell reselection
impact on the duration within E-
equipment. UTRAN, that is,
results in a shorter
duration. A larger
value leads to a
smaller impact.
A smaller value of
this parameter
impact of the UE
mobility state on the
The parameter actual value of the
modification has no timer for cell
impact on the reselection within E-
equipment. UTRAN, that is,
results in a higher
probability of cell
value leads to a
smaller impact.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
With other
conditions
unchanged, a larger
value of this
The parameter parameter indicates
modification has no a higher probability
impact on the of triggering intra-
equipment. frequency
measurements, and
a smaller value
indicates a lower
probability.
With other
conditions
unchanged, a larger
value of this
parameter leads to
The parameter
modification has no
None of triggering inter- V100R004C00 Radio
impact on the
frequency or inter-
equipment.
RAT
measurements, and
a smaller value
indicates a lower
probability.
The parameter
modification has no
impact on the
equipment.
With other
conditions
unchanged, a
parameter leads to
The parameter a lower probability
modification has no of reselection to an
impact on the inter-frequency or
equipment. inter-RAT cell on
lower-priority
frequencies, and a
parameter leads to
The parameter
modification has no
impact on the
equipment.
With other
conditions
unchanged, a
smaller parameter
value for a cell
leads to lower
probabilities of the
cell meeting criteria
S and becoming a
The parameter suitable cell for
modification has no selection, and a
impact on the larger parameter
equipment. value for a cell
leads to higher
probabilities. Set
this parameter
properly so that the
selected cell can
provide signals that
meet the quality
requirement of
basic services.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
When other
conditions remain
unchanged, an
increase in the
value of this
The parameter parameter results in
modification has no a decrease in the
equipment. reselection to the
neighboring cell,
and a decrease in
the value results in
an increase in the
probability.
The parameter
modification has no
impact on the
equipment.
A smaller value of
this parameter
impact of the UE
modification has no duration of cell
impact on the reselection to
equipment. CDMA2000 HRPD,
that is, results in a
shorter duration. A
larger value leads
to a smaller impact.
A smaller value of
this parameter
impact of the UE
modification has no duration of cell
impact on the reselection to
equipment. CDMA2000 HRPD,
that is, results in a
shorter duration. A
larger value leads
to a smaller impact.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.
The parameter
modification has no
impact on the
equipment.

Parameter Reference

Caricato da

Informazioni sul documento

Copyright

Formati disponibili

Condividi questo documento

Condividi o incorpora il documento

Opzioni di condivisione

Hai trovato utile questo documento?

Questo contenuto è inappropriato?

Copyright:

Formati disponibili

Parameter Reference

Caricato da

Copyright:

Formati disponibili

eNodeB

HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2012. All rights reserved.

Huawei Technologies Co., Ltd.

Huawei and the customer. All or part of the

ade in the preparation of this document to

Parameter Attribute Description

Service Interrupted After Modification

Parameter values recommended for different scenarios.

Product version in which the parameter is introduced.

nges, see the release notes.

parameter value comes from the radio network

es from the equipment plan.

e, to use this parameter, you need to set related

e equipment needs to be restarted after the

BFANT POLARMODE Polar Mode eNodeB DSP BFANT

BFANT AntPortNum Number of Port eNodeB DSP BFANT

AUTOPOWEROFF Auto power control MOD ENODEB

eNodeB LicenseState LicenseState eNodeB DSP ENODEB

Geo-coordinate MOD ENODEB

LATITUDESECFOR Latitude with MOD ENODEB

DETECTBEGINTIM MOD KPIALARM

DETECTPERIODN MOD KPIALARM

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the

Slot No. of the RRU ADD SECTOR

Cabinet No. of the

Subrack No. of the